Samsung | SAMSUNG WB30F | Samsung SMART CAMERA WB30F User Manual

USER
MANUAL
WB30F/WB31F/WB32F
Click a topic
This user manual includes detailed usage instructions for
your camera. Please read this manual thoroughly.
Basic troubleshooting
Quick reference
Contents
Basic functions
Extended functions
Shooting options
Playback/Editing
Wireless network
Settings
Appendixes
Index
Health and safety information
Always comply with the following precautions and usage tips to avoid dangerous situations and ensure peak performance of your camera.
Prevent damage to subjects’ eyesight.
Do not use the flash in close proximity (closer than 1 m/3 ft) to people or animals.
If you use the flash too close to your subject’s eyes, you can cause temporary or
permanent eyesight damage.
Warning—situations that could cause injury to yourself or others
Do not disassemble or attempt to repair your camera.
This may result in electric shock or damage to the camera.
Keep your camera away from small children and pets.
Keep your camera and all accessories out of the reach of small children and animals.
Small parts may cause choking or serious injury if swallowed. Moving parts and
accessories may present physical dangers as well.
Do not use your camera near flammable or explosive gases and liquids.
This may cause a fire or explosion.
Do not insert flammable materials into the camera or store these materials
near the camera.
This may cause a fire or electric shock.
Do not expose the camera to direct sunlight or high temperatures for an
extended period of time.
Prolonged exposure to sunlight or extreme temperatures can cause permanent
damage to your camera’s internal components.
Do not handle your camera with wet hands.
This may result in electric shock.
1
Health and safety information
Avoid covering the camera or charger with blankets or clothes.
The camera may overheat, which may distort the camera or cause a fire.
Avoid interference with pacemakers.
Maintain the distance between this camera and all pacemakers to avoid potential
interference, as recommended by the manufacturer and research groups. If you
have any reason to suspect that your camera is interfering with a pacemaker
or other medical device, turn off the camera immediately and contact the
manufacturer of the pacemaker or medical device for guidance.
Do not handle the power supply cord or go near the charger during a
thunderstorm.
This may result in electric shock.
If liquid or foreign objects enter your camera, immediately disconnect all
power sources, such as the battery or charger, and then contact a Samsung
service center.
Comply with any regulations that restrict the use of a camera in a certain area.
• Avoid interference with other electronic devices.
• Turn off the camera when in an aircraft. Your camera can cause interference with
aircraft equipment. Follow all airline regulations and turn off your camera when
directed by airline personnel.
• Turn off the camera near medical equipment. Your camera can interfere with
medical equipment in hospitals or health care facilities. Follow all regulations,
posted warnings, and directions from medical personnel.
2
Health and safety information
Caution—situations that could cause damage to your camera or other
equipment
Use the battery only for its intended purpose.
Misusing the battery may cause a fire or electric shock.
Remove the batteries from your camera when storing it for an extended period
of time.
Installed batteries may leak or corrode over time and cause serious damage to your
camera.
Do not touch the flash while it fires.
The flash is very hot when fired and may burn your skin.
When you use the AC charger, turn off the camera before you disconnect the
power to the AC charger.
Failing to do so may result in fire or electric shock.
Use only authentic, manufacturer-recommended, Lithium-ion replacement
batteries. Do not damage or heat the battery.
Inauthentic, damaged, or heated batteries may cause a fire or personal injury.
Disconnect the charger from the wall socket when not in use.
Failing to do so may result in fire or electric shock.
Use only Samsung-approved batteries, chargers, cables and accessories.
• Using unauthorized batteries, chargers, cables or accessories can cause batteries
to explode, damage your camera, or cause injury.
• Samsung is not responsible for damage or injuries caused by unapproved
batteries, chargers, cables or accessories.
Do not use a damaged power supply cord, plug, or loose outlet when you
charge batteries.
This may cause a fire or electric shock.
Do not allow the AC charger to come in contact with the +/- terminals on the
battery.
This may cause a fire or electric shock.
3
Health and safety information
Do not drop or subject the camera to strong impacts.
Doing so may damage the screen or external or internal components.
You must plug the small end of the USB cable into your camera.
If the cable is reversed, it may damage your files. The manufacturer is not
responsible for any loss of data.
Exercise caution when you connect cables or adapters and install batteries and
memory cards.
If you force the connectors, improperly connect cables, or improperly install
batteries and memory cards, you can damage ports, connectors, and accessories.
Avoid interference with other electronic devices.
Your camera emits radio frequency (RF) signals that may interfere with unshielded
or improperly shielded electronic equipment, such as pacemakers, hearing aids,
medical devices, and other electronic devices in homes or vehicles. Consult the
manufacturers of your electronic devices to solve any interference problems you
experience. To prevent unwanted interference, use only Samsung-approved devices
or accessories.
Keep cards with magnetic strips away from the camera case.
Information stored on the card may be damaged or erased.
Never use a damaged charger, battery, or memory card.
This may result in electric shock or camera malfunction or cause a fire.
Use your camera in the normal position.
Avoid contact with your camera’s internal antenna.
Do not place the camera in or near magnetic fields.
Doing so may cause the camera to malfunction.
Data transference and your responsibilities
Do not use the camera if the screen is damaged.
If the glass or acrylic parts are broken, visit a Samsung Electronics Service Center to
have the camera repaired.
• Data transferred via WLAN can be hacked, so avoid transferring sensitive data in
public areas or on open networks.
• The camera manufacturer is not liable for any data transfers that infringe on
copyrights, trademarks, intellectual property laws, or public decency ordinances.
Check that the camera is operating properly before use.
The manufacturer takes no responsibility for any loss of files or damage that may
result from camera malfunction or improper use.
4
Outline of the User Manual
Copyright information
• Microsoft Windows and the Windows logo are registered trademarks of the
Microsoft Corporation.
• Mac and Apple App Store are registered trademarks of the Apple
Corporation.
• Google Play Store is a registered trademark of Google, Inc.
• microSD™, microSDHC™, and microSDXC™ are registered trademarks of the
SD Association.
• Wi-Fi®, the Wi-Fi CERTIFIED logo, and the Wi-Fi logo are registered
trademarks of the Wi-Fi Alliance.
• Trademarks and trade names used in this manual are the property of their
respective owners.
Basic functions 18
Learn about your camera’s layout, icons, and basic functions for
shooting.
Extended functions 42
Learn how to capture a photo and record a video by selecting a
mode.
Shooting options 57
Learn how to set the options in Shooting mode.
Playback/Editing 78
Learn how to play back photos or videos, and edit photos. Also, learn
how to connect your camera to your computer or TV.
• Camera specifications or contents of this manual may be changed
without prior notice due to an upgrade of the camera's functions.
• We recommend using your camera within the country where you
purchased it.
• Use this camera responsibly and adhere to all laws and regulations
concerning its use.
• You are not allowed to reuse or distribute any part of this manual
without prior permission.
Wireless network 101
Learn how to connect to wireless local area networks (WLANs) and
use functions.
Settings 121
Refer to options to configure your camera’s settings.
Appendixes Get information about error messages, specifications, and
maintenance.
5
127
Icons used in this manual
Icon
Subject, background, and composition
• Subject: The main object in a scene, such as a person, animal, or still life
• Background: The objects around the subject
• Composition: The combination of a subject and background
Function
Additional information
Safety warnings and precautions
[]
()
→
*
Background
Camera buttons. For example, [Shutter] represents the shutter button.
Page number of related information
The order of options or menus you must select to perform a step; for
example: Select Face Detection → Normal (represents Select Face
Detection, and then select Normal).
Annotation
Subject
Expressions used in this manual
Exposure (Brightness)
The amount of light that enters your camera determines the exposure. You can alter
the exposure by changing the shutter speed, aperture value, or ISO sensitivity.
By altering the exposure, your photos will be darker or lighter.
Pressing the shutter
• Half-press [Shutter]: Press the shutter halfway down
• Press [Shutter]: Press the shutter all the way down
 Normal exposure
Half-press [Shutter]
Composition
Press [Shutter]
6
 Overexposure (too bright)
Special features of your camera
Using the DIRECT LINK button
Setting a DIRECT LINK button option
You can select a Wi-Fi function to launch when you press the DIRECT LINK button.
1 Access Settings.
2 Access the DIRECT LINK button option.
3 Select a Wi-Fi feature from the list.
Press the DIRECT LINK button to activate the Wi-Fi function that you have
designated.
7
Special
features of your camera

Using AutoShare
When you capture a photo with your camera, the photo is saved to the smart phone automatically. The camera connects to a smart phone wirelessly.
1 Install Samsung SMART CAMERA
4 Select the camera from the list and
App on the smart phone.
connect the smart phone to the
camera.
• If a pop-up message appears on your
camera, allow the smart phone to
connect to your camera.
2 Turn on the AutoShare feature.
5 Capture a photo.
• The captured photo is saved to the camera, and then transferred to the
smart phone.
3 Launch Samsung SMART CAMERA
App on the smart phone.
8
Special
features of your camera

Using MobileLink
You can send files easily from your camera to a smart phone. The camera connects wirelessly to smart phones that support the MobileLink feature.
1 Install Samsung SMART CAMERA
4 Select the camera from the list and
App on the smart phone.
connect the smart phone to the
camera.
• If a pop-up message appears on your
camera, allow the smart phone to
connect to your camera.
2 Access the MobileLink mode.
5 On the smart phone or camera,
• If a pop-up message appears, select an
option.
select files to transfer from the
camera.
3 Launch Samsung SMART CAMERA
6 On the smart phone, touch the copy
App on the smart phone.
button or on the camera, select
Share.
9
Special
features of your camera

Using Remote Viewfinder
You can remotely control your camera from a smart phone. The camera connects to a smart phone wirelessly. Use the smart phone as a remote shutter release with the Remote
Viewfinder feature. The captured photo will appear on the smart phone.
1 Install Samsung SMART CAMERA
4 Select the camera from the list and
App on the smart phone.
connect the smart phone to the
camera.
• If a pop-up message appears on your
camera, allow the smart phone to
connect to your camera.
5 Touch and hold
2 Access the Remote Viewfinder
to focus, and
then release it to capture a photo.
mode.
3 Launch Samsung SMART CAMERA
App on the smart phone.
6 Touch the thumbnail to view the
photo.
 10
Special
features of your camera

1 Select the macro option (
Shooting samples – Macro
You can capture close up shots of small subjects, such as flowers or insects.
2 Capture a photo.
The example image may differ from the actual photo that you capture.
 11
).
Basic troubleshooting
Learn to solve common problems by setting shooting options.
The subject’s eyes
appear red.
Red eye occurs when the subject's eyes reflect light from the camera flash.
• Set the flash option to
Red-eye or
Red-eye Fix. (p. 61)
• If the photo has already been captured, select
Red-eye Fix in the edit menu. (p. 91)
Photos have dust spots.
If dust particles are present in the air, you may capture them in photos when you use the flash.
• Turn off the flash or avoid capturing photos in a dusty place.
• Set ISO sensitivity options. (p. 63)
Photos are blurred.
Blurring can occur if you capture photos in low light conditions or hold the camera incorrectly.
Use the OIS function or half-press [Shutter] to ensure the subject is in focus. (p. 40)
Photos are blurred when
shooting at night.
As the camera tries to let in more light, the shutter speed slows. This can make it difficult to hold the camera steady long
enough to capture a clear photo and may result in camera shake.
• Select Night Shot mode. (p. 51)
• Turn on the flash. (p. 61)
• Set ISO sensitivity options. (p. 63)
• Use a tripod to prevent your camera from shaking.
When the light source is behind the subject or when there is a high contrast between light and dark areas, the subject may
appear too dark.
• Avoid shooting toward the sun.
• Select Backlight in Scene mode. (p. 47)
Fill in. (p. 61)
• Set the flash option to
• Adjust the exposure. (p. 69)
• Set the Auto Contrast Balance (ACB) option. (p. 70)
• Set the metering option to
Spot if a subject is in the center of the frame. (p. 70)
Subjects come out
too dark because of
backlighting.
 12
Quick reference
Capturing photos of people
• Beauty Shot mode  50
• Red-eye/Red-eye Fix (to prevent or correct red-eye)
 61
• Face Detection  67
Capturing photos at night or in the dark
•
•
•
•
Scene mode > Sunset, Dawn  47
Night Shot mode  51
Flash options  61
ISO sensitivity (to adjust the sensitivity to light)  63
Adjusting the exposure (brightness)
• ISO sensitivity (to adjust the sensitivity to light)  63
• EV (to adjust exposure)  69
• ACB (to compensate for subjects against bright
backgrounds)  70
• Metering  70
• AEB (to capture 3 photos of the same scene with
different exposures)  73
Capturing photos of scenery
• Scene mode > Landscape  47
• Live Panorama mode  48
Capturing action photos
• Continuous, Motion Capture  73
Capturing photos of text, insects, or
flowers
• Scene mode > Text  47
• Close-up Shot mode  51
• Macro  64
Applying effects to photos
•
•
•
•
•
Magic Frame mode  52
Photo Filter mode  52
Split Shot mode  54
Motion Photo mode  55
Image Adjust (to adjust Sharpness, Contrast, or
Saturation)  74
 13
Applying effects to videos
• Movie Filter mode  53
Reducing camera shake
• Optical Image Stabilization (OIS)  39
•
•
•
•
•
•
•
•
•
•
•
•
•
Viewing files as thumbnails  80
Viewing files by category  81
Deleting all files on the memory  83
Viewing files as a slide show  85
Viewing files on a TV  92
Connecting your camera to a computer  93
Sending photos or videos via email  112
Using photo or video sharing websites  115
Adjusting sound and volume  123
Adjusting the brightness of the display  124
Changing the display language  125
Setting the date and time  125
Before contacting a service center  139
Contents
Basic functions . .............................................................................................................. 18
Extended functions ...................................................................................................... 42
Unpacking . .................................................................................................................. 19
Using Basic modes .................................................................................................... 43
Camera layout ............................................................................................................ 20
Using the Smart Auto mode . ................................................................................
Using the Program mode . .....................................................................................
Using the Smart Movie mode ...............................................................................
Using the Movie mode .........................................................................................
Using the Scene mode ...........................................................................................
Using the Live Panorama mode . ..........................................................................
Using the DIRECT LINK button .............................................................................. 22
Inserting the battery and memory card .......................................................... 23
Charging the battery and turning on your camera ...................................... 24
Charging the battery .............................................................................................. 24
Turning on your camera ......................................................................................... 24
43
44
45
46
47
48
Using Scene modes .................................................................................................. 50
Performing the initial setup ................................................................................. 25
Using the Beauty Shot mode ................................................................................
Using the Night Shot mode . .................................................................................
Using the Close-up Shot mode . ...........................................................................
Using the Magic Frame mode ...............................................................................
Using the Photo Filter mode ................................................................................
Using the Movie Filter mode ................................................................................
Using the Split Shot mode .....................................................................................
Using the Motion Photo mode .............................................................................
Learning icons ............................................................................................................ 27
Using the Home screen ........................................................................................... 28
Accessing the Home screen .................................................................................. 28
Icons on the Home screen ..................................................................................... 29
Setting Wallpaper .................................................................................................... 31
Selecting options or menus .................................................................................. 32
Setting the display and sound ............................................................................. 34
Setting the display type ......................................................................................... 34
Setting the sound . .................................................................................................. 35
Capturing photos ...................................................................................................... 36
Zooming ................................................................................................................... 37
Reducing camera shake (OIS) . .............................................................................. 39
Tips for getting a clearer photo ........................................................................... 40
 14
50
51
51
52
52
53
54
55

Contents
Shooting options . ......................................................................................................... 57
Using Face Detection ............................................................................................... 67
Detecting faces ........................................................................................................
Capturing a smile shot . .........................................................................................
Detecting eye blinking ..........................................................................................
Tips for detecting faces ..........................................................................................
Selecting a resolution and quality ...................................................................... 58
Selecting a resolution ............................................................................................. 58
Selecting a photo quality ....................................................................................... 59
Using the timer . ......................................................................................................... 60
67
67
68
68
Adjusting brightness and color ........................................................................... 69
Shooting in the dark ................................................................................................ 61
Adjusting the exposure manually (EV) ................................................................
Compensating for backlighting (ACB) .................................................................
Changing the metering option . ...........................................................................
Selecting a White Balance setting ........................................................................
Preventing red-eye . ................................................................................................ 61
Setting a flash option ............................................................................................. 61
Adjusting the ISO sensitivity . ................................................................................ 63
Changing the camera’s focus ................................................................................ 64
69
70
70
71
Using burst modes . .................................................................................................. 73
Using macro ............................................................................................................. 64
Using auto focus ...................................................................................................... 64
Adjusting the focus area ........................................................................................ 65
Adjusting images ...................................................................................................... 74
Reducing the sound of the zoom ........................................................................ 75
Available shooting options by shooting mode . ............................................ 76
 15
Contents
Playback/Editing . .......................................................................................................... 78
Wireless network ......................................................................................................... 101
Viewing photos or videos in Playback mode .................................................. 79
Connecting to a WLAN and configuring network settings ...................... 102
Starting Playback mode ......................................................................................... 79
Viewing photos . ...................................................................................................... 83
Playing a video . ....................................................................................................... 86
Connecting to a WLAN .........................................................................................
Using the login browser .......................................................................................
Network connection tips .....................................................................................
Entering text . .........................................................................................................
Editing a photo . ......................................................................................................... 88
Resizing photos .......................................................................................................
Rotating a photo .....................................................................................................
Applying Smart Filter effects .................................................................................
Adjusting your photos . ..........................................................................................
102
103
104
105
Saving files to a smart phone automatically ................................................. 106
88
88
89
90
Sending photos or videos to a smart phone . ............................................... 107
Using a smart phone as a remote shutter release . ..................................... 108
Using Auto Backup to send photos or videos . ............................................ 110
Viewing files on a TV ................................................................................................ 92
Installing the program for Auto Backup on your PC . ...................................... 110
Sending photos or videos to a PC ...................................................................... 110
Transferring files to the computer ...................................................................... 93
Transferring files to your Windows OS computer .............................................. 93
Transferring files to your Mac OS computer ...................................................... 94
Sending photos or videos via email ................................................................. 112
Changing email settings ...................................................................................... 112
Sending photos or videos via email ................................................................... 114
Using programs on a computer ........................................................................... 95
Installing i-Launcher ............................................................................................... 95
Using i-Launcher ..................................................................................................... 96
Using photo or video sharing websites .......................................................... 115
Accessing a website .............................................................................................. 115
Uploading photos or videos . .............................................................................. 115
Using AllShare Play to send files . ...................................................................... 117
Uploading photos to online storage . ................................................................ 117
Viewing photos or videos on devices that support AllShare Play . ............... 118
Sending photos using Wi-Fi Direct ................................................................... 120
 16
Contents
Settings ............................................................................................................................ 121
Settings menu .......................................................................................................... 122
Accessing the settings menu ..............................................................................
Sound ......................................................................................................................
Display . ...................................................................................................................
Connectivity ...........................................................................................................
General . ..................................................................................................................
122
123
123
124
125
Appendixes .................................................................................................................... 127
Error messages ......................................................................................................... 128
Camera maintenance . ........................................................................................... 130
Cleaning your camera ..........................................................................................
Using or storing the camera ................................................................................
About memory cards . ..........................................................................................
About the battery . ................................................................................................
130
131
132
135
Before contacting a service center ................................................................... 139
Camera specifications . .......................................................................................... 142
Glossary ...................................................................................................................... 146
Index ............................................................................................................................ 151
 17
Basic functions
Learn about your camera’s layout, icons, and basic functions for shooting.
Unpacking … ……………………………………… 19
Camera layout … …………………………………… 20
Selecting options or menus … …………………… 32
Setting the display and sound … ………………… 34
Using the DIRECT LINK button … ………………… 22
Setting the display type …………………………… 34
Setting the sound … ……………………………… 35
Inserting the battery and memory card ………… 23
Charging the battery and turning on
your camera ………………………………………… 24
Charging the battery ……………………………… 24
Turning on your camera … ……………………… 24
Performing the initial setup … …………………… 25
Learning icons ……………………………………… 27
Using the Home screen … ………………………… 28
Accessing the Home screen … …………………… 28
Icons on the Home screen ………………………… 29
Setting Wallpaper … ……………………………… 31
Capturing photos … ……………………………… 36
Zooming … ……………………………………… 37
Reducing camera shake (OIS) … ………………… 39
Tips for getting a clearer photo …………………… 40
Unpacking
The following items are included in your product box.
Optional accessories
Camera
Rechargeable battery
AC adapter/USB cable
Camera case
A/V cable
Battery charger
Memory card/Memory card adapter
Strap
Quick Start Guide
• The illustrations may differ slightly from the items shipped with your product.
• The items included in the box may differ depending on the model.
• You can purchase optional accessories at a retailer or a Samsung service center.
Samsung is not responsible for any problems caused by using unauthorized
accessories.
Basic functions 19
Camera layout
Before you start, familiarize yourself with your camera’s parts and their functions.
Power button
Microphone
Shutter button
Speaker
Flash
Internal antenna*
* Avoid contact with the internal antenna while using
the wireless network.
AF-assist light/Timer lamp
Lens
Tripod mount
USB and A/V port
Accepts USB cable and A/V cable
Battery chamber cover
Insert a memory card and battery
Basic functions 20
Camera layout
Zoom button
• In Shooting mode: Zoom in or out
• In Playback mode: Zoom in on part of a photo or
view files as thumbnails, or adjust the volume
Attaching the strap
Status lamp
• Blinking: When the camera is saving a photo
or video, being read by a computer, when the
image is out of focus, or there is a problem
charging the battery, when the camera is
connecting to WLAN or sending a photo
• Steady: When the camera is connected to a
computer, charging the battery, or when the
image is in focus
Button
Description
Display
Buttons
(See the table below)
Button
Start a preset Wi-Fi function. (p. 22)
Description
Basic functions
Change the display option.
Access the Home screen. (p. 28)
Change the macro option.
Change the flash option.
Change the timer option.
Access options or menus.
Enter Playback mode.
Delete files in Playback mode.
Confirm the highlighted option or menu.
Basic functions 21
Other functions
Move up
Move down
Move left
Move right
Camera layout
Using the DIRECT LINK button
You can turn on the Wi-Fi feature conveniently with [ ].
Press [ ] to activate the Wi-Fi function that you have designated.
Press [ ] again to return to the previous mode.
Setting a DIRECT LINK button option
You can select a Wi-Fi function to launch when you press [
].
1 On the Home screen, scroll to <Basic>.
2 Select .
3 Select General → DIRECT LINK (Wi-Fi Button).
4 Select a Wi-Fi feature. (p. 126)
Basic functions 22
Inserting the battery and memory card
Learn how to insert the battery and an optional memory card into the camera.
Removing the battery and memory card
Slide the lock down to release the
battery.
Battery lock
Rechargeable battery
Insert a memory card with the gold-colored
contacts facing up.
Memory card
Push the card gently until it disengages from
the camera, and then pull it out of the slot.
Memory card
Insert the battery with the Samsung logo
facing up.
You can use the internal memory for temporary storage if a memory card is not
inserted.
Rechargeable battery
Basic functions 23
Charging the battery and turning on your camera
Charging the battery
Turning on your camera
Before you use the camera for the first time, you must charge the battery. Plug the
small end of the USB cable into your camera, and then plug the other end of the
USB cable into the AC adapter.
Press [ ] to turn your camera on or off.
• The initial setup screen appears when you turn on
the camera for the first time. (p. 25)
Turning on your camera in Playback mode
Status lamp
• Red light on: Charging
• Red light off: Fully charged
• Red light blinking: Error
Press [ ]. The camera turns on and immediately
accesses Playback mode.
Use only the AC adapter and USB cable supplied with your camera. If you use
another AC adapter (such as SAC-48), the camera battery may not charge or work
properly.
Basic functions 24
Performing the initial setup
When you turn on your camera for the first time, the initial setup screen appears. Follow the steps below to configure the camera’s basic settings. The language is preset for the
country or region where the camera is sold. You can change the language as desired.
1 Press [
2 Press [
] to select Time Zone, and then press [
] or [
] to select Home, and then press [
/
5 Press [
].
].
/
] to select a time zone, and then press [
] or [
].
Date/Time Set
• When you travel to another country, select Visit, and then select a new time
zone.
3 Press [
] to select Date/Time Set, and then press [
Year Month Day Hour Min
DST
].
Time Zone : Home
Cancel
Set
• The screen may differ depending on the language selected.
London
Cancel
4 Press [
Set
].
6 Press [
7 Press [
/
then press [
Basic functions 25
] to select an item.
/
] to set the date, time, and daylight-saving time, and
].
Performing the initial setup
8 Press [
9 Press [
10 Press [
11 Press [
12 Press [
] to select Date Type, and then press [
/
] or [
].
] to select a date type, and then press [
].
] to select Time Type, and then press [
/
] or [
].
] to select a time type, and then press [
].
] to finish the initial setup.
Basic functions 26
Learning icons
The icons the camera displays on the screen change according to the mode you select or the options you set. If you change a shooting option, the corresponding icon will blink
briefly in yellow.
1
2 Shooting option (right)
Icon
Description
Intelli zoom on
2
Continuous auto focus activated
Photo resolution
Video resolution
Metering
Frame rate (per second)
3
1 Shooting options (left)
Icon
Flash
Sound Alive on
Description
Optical Image Stabilization (OIS)
Shooting mode
Focus Option
Exposure value adjusted
ISO sensitivity
Image adjustment (sharpness, contrast,
and saturation)
White balance
Timer
3 Shooting information
Icon
Description
Current date
Current time
Available number of photos
Memory card inserted
•
•
•
•
: Fully charged
: Partially charged
: Empty (Recharge)
: Charging (Connected with the
charger)
Aperture value
Shutter speed
Available recording time
Auto focus frame
Camera shake
Zoom indicator
Photo resolution when the
Intelli zoom is on
Face detection
Face tone
Zoom ratio
Burst option
AutoShare On
Basic functions 27
Using the Home screen
You can select a shooting mode or access the settings menu by selecting the icons on the Home screen.
Accessing the Home screen
In Shooting or Playback mode, press [
mode.
No.
]. Press [
] again to return to the previous
1
2
1
Album
Basic
Smart Auto Program
Scene
Back
Live
Panorama
Wi-Fi
Smart
Movie
Movie
2
Settings
Page Move
Basic functions 28
Description
Current Home screen
• Rotate [Zoom] to the left or right to switch to another Home screen.
• Press [
] to scroll to the Home screen name, and then press [ / ]
to switch to another Home screen.
• Press [ / ] repeatedly to switch to another Home screen.
Mode icons
• Press [
/ / / ] to scroll to a desired mode, and then press [ ]
to access the mode.
Using the Home screen
Icons on the Home screen
<Wi-Fi>
Icon
<Basic>
Icon
Description
Smart Auto: Capture a photo with a scene mode selected
automatically by the camera. (p. 43)
Program: Capture a photo with settings you have adjusted manually.
(p. 44)
Smart Movie: Record a video with a scene mode selected
automatically by the camera. (p. 45)
Movie: Record a video. (p. 46)
Scene: Capture a photo with options that are preset for a specific scene.
(p. 47)
Live Panorama: Capture and combine a series of photos to create a
panoramic image. (p. 48)
Settings: Adjust settings to match your preferences. (p. 122)
Basic functions 29
Description
MobileLink: Send photos or videos to a smart phone. (p. 107)
Remote Viewfinder: Use a smart phone as a remote shutter release
and see a preview on your smart phone of an image from your camera.
(p. 108)
Auto Backup: Send photos or videos that you captured with the
camera to a PC wirelessly. (p. 110)
Email: Send photos or videos stored on the camera via email. (p. 112)
SNS & Cloud: Upload photos or videos to file sharing websites. (p. 115)
AllShare Play: Upload photos to AllShare Play online storage or view
files on other AllShare Play supported devices. (p. 117)
Using the Home screen
<Album>
<Scene>
Icon
Icon
Description
Description
Beauty Shot: Capture a portrait with options to hide facial
imperfections. (p. 50)
Album: View files as thumbnails. (p. 80)
Night Shot: Capture a night scene by adjusting shutter speed. (p. 51)
Photo Editor: Edit photos with various effects. (p. 88)
Close-up Shot: Capture close-up photos of subjects. (p. 51)
Magic Frame: Capture a photo with various frame effects. (p. 52)
Photo Filter: Capture a photo with various filter effects. (p. 52)
Movie Filter: Record a video with various filter effects. (p. 53)
Split Shot: Capture several photos and arrange them with preset
layouts. (p. 54)
Motion Photo: Capture and combine a series of photos, and then
select an area to be animated to create a GIF animation. (p. 55)
Basic functions 30
Using the Home screen
5 Scroll to the desired wallpaper, and then press [
Setting Wallpaper
Set wallpaper for the Home screen with the desired image.
1 On the Home screen, scroll to <Basic>.
2 Select .
3 Select Display → Wallpapers.
4 Select an option.
Option
Wallpaper Gallery
Album
].
• If you select a photo you have captured, you can set a specified area as
wallpaper. Rotate [Zoom] to the left or right to reduce or enlarge the area.
/ / / ] to move the area.
Press [
6 Press [
] to save.
• If you select a photo you have captured, press [
], and then select Yes.
You can also set the photo you are viewing as wallpaper by pressing [
and then selecting Set Wallpaper in Playback mode.
Description
Select the desired wallpaper from the default gallery.
Set a photo you have captured as a wallpaper.
Basic functions 31
],
Selecting options or menus
To select an option or a menu, press [
], and then press [
1 In Shooting or Playback mode, press [
2 Scroll to an option or a menu.
• To move up or down, press [
] or [
• To move left or right, press [ ] or [ ].
3 Press [
].
/ / / ] or [
].
Going back to the previous menu
Press [
].
] to go back to the previous menu.
Half-press [Shutter] to return to Shooting mode.
] to confirm the highlighted option or menu.
Basic functions 32
Selecting options or menus
For example, to select a White Balance option in Program mode:
4 Press [
1 On the Home screen, scroll to <Basic>.
2 Select .
].
3 Press [
/
AutoShare
EV
White Balance
ISO
AutoShare
Flash
EV
Focus
White Balance
Exit
ISO
5 Press [
Flash
] to select White Balance, and then press [
/
Select
] to select a White Balance option.
Focus
Exit
Select
White Balance : Daylight
Back
6 Press [
Basic functions 33
Select
] to save your settings.
] or [
].
Setting the display and sound
Learn how to change the basic display information and sound settings.
Setting the display type
Setting the option display view
You can select a display type for the Shooting or Playback mode. Each type displays
different shooting or playback information. See the table below.
You can hide or show the option display appearing in some modes.
Press [ ] repeatedly.
• Hide the option display.
• Show the option display.
Landscape
Press [
Option display
] repeatedly to change the display type.
Panel off
▲ For example, in Scene mode
Mode
Display type
Shooting
• Hide all information about shooting options.
• Show all information about shooting options.
Playback
• Hide all information about the current file.
• Hide all information about the current file except basic information.
• Show all information about the current file.
Basic functions 34
Setting the display and sound
Setting the sound
Turn the sound your camera emits when you perform functions on or off.
1 On the Home screen, scroll to <Basic>.
2 Select .
3 Select Sound → Beep Sound.
4 Select an option.
Option
Off
On
Description
The camera does not emit any sounds.
The camera emits sounds.
Basic functions 35
Capturing photos
Learn how to capture photos easily and quickly in Smart Auto mode.
1 On the Home screen, scroll to <Basic>.
2 Select .
3 Align your subject in the frame.
4 Half-press [Shutter] to focus.
• A green frame means the subject is in focus.
• A red frame means the subject is out of focus.
5 Press [Shutter] to capture a photo.
6 Press [ ] to view the captured photo.
• To delete the photo, press [
7 Press [
], and then select Yes.
] to return to Shooting mode.
See page 40 for tips to get clearer photos.
Basic functions 36
Capturing photos
Zooming
Digital zoom
You can capture close-up photos by adjusting the zoom.
The Digital zoom is supported by default in Shooting mode. If you zoom in on
a subject in Shooting mode and the zoom indicator is in the digital range, your
camera is using the Digital zoom. By using both the 10X Optical zoom and 5X
Digital zoom, you can zoom in up to 50 times.
Optical range
Zoom indicator
Digital range
• The Digital zoom is not available with the Tracking AF option.
• If you capture a photo with the Digital zoom, the photo quality may be lower
than normal.
Zoom ratio
Zoom out
Zoom in
When you rotate the zoom button, the zoom ratio shown on the screen may
change inconsistently.
Basic functions 37
Capturing photos
Intelli zoom
Setting Intelli zoom
If the zoom indicator is in the Intelli range, your camera is using the Intelli zoom.
Photo resolution varies according to the zoom ratio if you use the Intelli zoom. By
using both the Optical zoom and Intelli zoom, you can zoom in up to 20 times.
Photo resolution
when the Intelli
zoom is on
Optical range
1 In Shooting mode, press [
2 Select Intelli Zoom.
3 Select an option.
Icon
].
Description
Off: The Intelli zoom is deactivated.
Zoom indicator
On: The Intelli zoom is activated.
Intelli range
• Intelli zoom is not available with the Text option in SCN mode and the Tracking AF
option.
• The Intelli zoom helps you capture a photo with less quality deterioration than
the Digital zoom. However, the photo quality may be lower than when you use
the Optical zoom.
• The Intelli zoom is available only when you set a 4:3 resolution ratio. If you set
another resolution ratio with Intelli zoom on, the Intelli zoom will be turned off
automatically.
• The Intelli zoom is always on in Smart Auto mode.
Basic functions 38
Capturing photos
Reducing camera shake (OIS)
• OIS may not function properly when:
-- you move your camera to follow a moving subject
-- you use the Digital zoom
-- there is too much camera shake
-- the shutter speed is slow (for example, when you capture night scenes)
-- the battery is low
-- you capture a close-up shot
• If you use the OIS function with a tripod, your images may be blurred by the
vibration of the OIS sensor. Deactivate the OIS function when you use a tripod.
• If the camera is hit or dropped, the display will be blurry. If this occurs, turn off
the camera, and then turn it on again.
Reduce camera shake optically in Shooting mode.
 Before correction
 After correction
1 In Shooting mode, press [
2 Select OIS.
3 Select an option.
Icon
].
Description
Off: OIS is deactivated.
On: OIS is activated.
Basic functions 39
Tips for getting a clearer photo
   Holding your camera correctly
   Reducing camera shake
Ensure nothing is blocking the lens,
flash, or microphone.
Set the Optical Image Stabilization option to reduce camera
shake optically. (p. 39)
   When
   Half-pressing the shutter button
is displayed
Half-press [Shutter] and adjust the focus. The camera
adjusts the focus and exposure automatically.
Camera shake
The camera sets the aperture value and shutter
speed automatically.
Focus frame
• Press [Shutter] to capture the photo if the
focus frame appears in green.
When you shoot in the dark, avoid setting the flash option to Slow Sync or Off.
The aperture remains open longer and it may be harder to hold the camera steady
long enough to capture a clear photo.
• Use a tripod or set the flash option to Fill in. (p. 61)
• Set ISO sensitivity options. (p. 63)
• Change the composition and half-press
[Shutter] again if the focus frame appears in red.
Basic functions 40
   Preventing your subject from being out of focus
It may be difficult to get your subject in focus when:
-- there is little contrast between the subject and background (for example,
when your subject is wearing clothing that is similar in color to the
background)
-- the light source behind the subject is too bright
-- the subject is shiny or reflective
-- the subject includes horizontal patterns, such as blinds
-- the subject is not positioned in the center of the frame
• When you capture photos in low light
Turn on the flash.
(p. 61)
• When subjects are moving rapidly
Use the Continuous
or Motion Capture
function. (p. 73)
Using the focus lock
Half-press [Shutter] to focus. When the subject is in focus, you can
reposition the frame to change the composition. When you are ready,
press [Shutter] to capture your photo.
Basic functions 41
Extended functions
Learn how to capture a photo and record a video by selecting a mode.
Using Basic modes … ……………………………… 43
Using the Smart Auto mode ………………………
Using the Program mode … ………………………
Using the Smart Movie mode … …………………
Using the Movie mode ……………………………
Using the Scene mode … …………………………
Using the Live Panorama mode … ………………
43
44
45
46
47
48
Using Scene modes ………………………………… 50
Using the Beauty Shot mode … …………………
Using the Night Shot mode … ……………………
Using the Close-up Shot mode ……………………
Using the Magic Frame mode … …………………
Using the Photo Filter mode ………………………
Using the Movie Filter mode … …………………
Using the Split Shot mode …………………………
Using the Motion Photo mode ……………………
50
51
51
52
52
53
54
55
Using Basic modes
Capture photos or record videos using basic modes. You can also use the Scene mode and the Live Panorama mode.
Using the Smart Auto mode
Icon
Description
In Smart Auto mode, your camera automatically chooses the appropriate camera
settings based on the type of scene it detects. The Smart Auto mode is helpful if you
are not familiar with the camera settings for various scenes.
Portraits at night
1 On the Home screen, scroll to <Basic>.
2 Select .
3 Align your subject in the frame.
Portraits with backlighting
Landscapes with backlighting
Portraits
Close-up photos of objects
• The camera automatically selects a scene. An appropriate scene icon appears
at the top left of the screen. The icons are listed below.
Close-up photos of text
Sunsets
Blue skies
Forested areas
Close-up photos of colorful subjects
Camera is stabilized or on a tripod (when shooting in the dark)
Actively moving subjects
Fireworks (when using a tripod)
Icon
Indoors, dark
Description
Partially lit
Landscapes
Close-up with spot lighting
Scenes with bright white backgrounds
Portraits with spot lighting
Landscapes at night
Extended functions 43
Using Basic modes
4 Half-press [Shutter] to focus.
5 Press [Shutter] to capture the photo.
Using the Program mode
In Program mode, you can set most options, except the shutter speed and aperture
value, which the camera sets automatically.
• If the camera does not recognize an appropriate scene mode, it uses the default
settings for the Smart Auto mode.
• Even if it detects a face, the camera may not select a portrait mode depending
on the subject's position or lighting.
• The camera may not select the correct scene depending on the shooting
conditions, such as camera shake, lighting, or distance to the subject.
• Even if you use a tripod, the camera may not detect the
mode if the subject
is moving.
• The camera consumes more battery power, because it changes settings often to
select appropriate scenes.
1 On the Home screen, scroll to <Basic>.
2 Select .
3 Set the desired options.
• For a list of options, refer to "Shooting options". (p. 57)
4 Align your subject in the frame, and then half-press [Shutter] to
focus.
5 Press [Shutter] to capture the photo.
Extended functions 44
Using Basic modes
Using the Smart Movie mode
Icon
Description
In Smart Movie mode, your camera automatically chooses the appropriate camera
settings based on the scene it has detected. This mode is available only when you
insert a memory card into the camera.
Landscapes
1 On the Home screen, scroll to <Basic>.
2 Select .
3 Align your subject in the frame.
Blue skies
Sunsets
Forested areas
• The camera automatically selects a scene. An appropriate scene icon will
appear at the top left of the screen.
4 Press [Shutter] to start recording.
5 Press [Shutter] again to stop recording.
• If the camera does not recognize an appropriate scene mode, it uses the default
settings for Smart Movie mode.
• The camera may not select the correct scene depending on the shooting
conditions, such as camera shake, lighting, and distance to the subject.
Extended functions 45
Using Basic modes
Using the Movie mode
In Movie mode, you can customize settings to record HD videos (1280x720) of up
to 20 minutes in length. The camera saves recorded videos as MP4 (H.264) files. This
mode is available only when you insert a memory card into the camera.
• H.264 (MPEG-4 part10/AVC) is a high-compression video format established by
the international standards organizations ISO-IEC and ITU-T.
• If you use memory cards with slow write speeds, the camera may not save
videos properly. Video recordings may be corrupted or fail to play back
correctly.
• Memory cards with slow writing speeds will not support high-resolution videos.
To record high-resolution videos, use memory cards with faster write speeds.
• If you activate the Image Stabilization function while recording a video, the
camera may record the operating sound of the Image Stabilization function.
• If you use the zoom function when recording a video, the camera may record
the noise of the zoom operating. To decrease zoom noise, use the Sound Alive
function. (p. 75)
•
(Continuous AF): Use this function to shoot by changing composition
while automatically focusing on the center area.
1 On the Home screen, scroll to <Basic>.
2 Select .
3 Set desired options.
• For a list of options, refer to "Shooting options". (p. 57)
4 Press [Shutter] to start recording.
• While recording a video, press [ ] once to cancel the continuous auto
focus function and once again to activate the function.
5 Press [Shutter] again to stop recording.
Extended functions 46
Using Basic modes
Using the Scene mode
Pause recording
The camera allows you to temporarily pause a video while recording. With this
function, you can record separate scenes as a single video.
In Scene mode, you can capture a photo with options that are preset for a specific
scene.
1 On the Home screen, scroll to <Basic>.
2 Select .
3 Select a scene.
OK : Pause
• Press [
• Press [
: Continuous AF Off
] to pause while recording.
] to resume.
Landscape
Panel off
Extended functions 47
Using Basic modes
Option
Using the Live Panorama mode
Description
Landscape
Capture still-life scenes and landscapes.
Capture scenes at sunset, with natural-looking reds and
Sunset
yellows.
Dawn
Capture scenes at sunrise.
Backlight
Capture backlit subjects.
Reduce underexposure of subjects caused by sunlight
Beach & Snow
reflected from sand or snow.
Text
Clearly capture text from printed or electronic documents.
4
Align your subject in the frame, and then half-press [Shutter] to
focus.
5 Press [Shutter] to capture the photo.
In Live Panorama mode, you can capture a wide panoramic scene in a single
photo. Capture and combine a series of photos to create a panoramic image.
 Shooting example
1 On the Home screen, scroll to <Basic>.
2 Select .
3 Align your subject in the frame, and then half-press [Shutter] to
focus.
• Align the camera with the far left or the far right, or very top or bottom, of the
scene you want to capture.
4 Press and hold [Shutter] to start shooting.
Extended functions 48
Using Basic modes
5 With [Shutter] pressed, slowly move the camera in the direction
that will let it capture the rest of the panorama.
• Arrows toward the direction of motion are displayed, and the entire
shooting image is displayed in the preview box.
• When the viewfinder is aligned with the next scene, the camera captures
the next photo automatically.
6 When you are finished, release [Shutter].
• When you have captured all the necessary shots, the camera combines
them into one panoramic photo.
Extended functions 49
• For best results when capturing panoramic photos, avoid the following:
-- moving the camera too quickly or too slowly
-- moving the camera too little to capture the next image
-- moving the camera at irregular speeds
-- shaking the camera
-- shooting in dark places
-- capturing moving subjects nearby
-- shooting conditions where the brightness or color of light is changing
• Photos taken are automatically saved, and shooting is stopped under the
following conditions:
-- if you change the shooting direction while shooting
-- if you move the camera too rapidly
-- if you don't move the camera
• Selecting Live Panorama mode will disable the digital and optical zoom
functions. If you select Live Panorama mode while the lens is zoomed in, the
camera automatically zooms out to the default position.
• Some shooting options are not available.
• The camera may stop shooting due to the shooting composition or movement
within the scene.
• Your camera may not capture the last scene in its entirety if you stop moving
the camera exactly where you want the scene to end. To capture the entire
scene, move your camera slightly beyond the point where you want the scene
to end.
Using Scene modes
Capture a photo or record a video by selecting appropriate modes for various scenes or effects.
6 Press [
Using the Beauty Shot mode
In Beauty Shot mode, you can capture a portrait with options to hide facial
imperfections.
/
1 On the Home screen, scroll to <Scene>.
2 Select .
3 Press [ / ] to adjust Face Retouch.
Face Tone : 2
• For example, increase the face retouch setting to hide more imperfections.
Cancel
Face Retouch : 2
Panel off
] to adjust Face Tone.
• For example, increase the face tone setting to make skin appear lighter.
Set
7 Press [ ] to save the setting.
8 Align your subject in the frame, and then half-press [Shutter] to
focus.
9 Press [Shutter] to capture the photo.
].
4 Press [
5 Select Face Tone.
Extended functions 50
Using Scene modes
Using the Night Shot mode
Using the Close-up Shot mode
In Night Shot mode, you can use a slow shutter speed to extend the time the
shutter stays open. Increase the aperture value to prevent overexposure.
In Close-up Shot mode, you can capture close-up photos of subjects, such as
flowers or insects.
1 On the Home screen, scroll to <Scene>.
2 Select .
3 Press [ / ] to adjust the shutter speed.
1 On the Home screen, scroll to <Scene>.
2 Select .
3 Align your subject in the frame, and then half-press [Shutter] to
focus.
Shutter Speed : Auto
Panel off
4 Align your subject in the frame, and then half-press [Shutter] to
focus.
5 Press [Shutter] to capture the photo.
4 Press [Shutter] to capture the photo.
Use a tripod to prevent blurry photos.
Extended functions 51
Using Scene modes
Using the Magic Frame mode
Using the Photo Filter mode
In Magic Frame mode, you can apply various frame effects to your photos. The
shape and the feel of the photos will change according to the frame you select.
Apply various filter effects to your photos to create unique images.
1 On the Home screen, scroll to <Scene>.
2 Select .
3 Select a desired frame.
Miniature
Vignetting
4 Align your subject in the frame, and then half-press [Shutter] to
Fish-eye
Sketch
5 Press [Shutter] to capture the photo.
1 On the Home screen, scroll to <Scene>.
2 Select .
Wall Art
Panel off
focus.
In Magic Frame mode, the resolution is automatically set to
.
Extended functions 52
Using Scene modes
3 Select an effect.
Option
Miniature
Vignetting
Ink Painting
Oil Painting
Cartoon
Cross Filter
Sketch
Soft Focus
Fish-eye
Old Film
Half Tone Dot
Classic
Retro
Zooming Shot
4 Align your subject in the frame, and then half-press [Shutter] to
Description
Apply a tilt-shift effect to make the subject appear in
miniature.
Apply the retro-looking colors, high contrast, and strong
vignette effect of Lomo cameras.
Apply a watercolor painting effect.
Apply an oil painting effect.
Apply a cartoon painting effect.
Add lines that radiate outward from bright objects to
imitate the visual effect of a cross filter.
Apply a pen sketch effect.
Hide facial imperfections or apply dreamy effects.
Blacken the edges of the frame and distort objects to
imitate the visual effect of a fisheye lens.
Apply a vintage film effect.
Apply a halftone effect.
Apply a black and white effect.
Apply a sepia tone effect.
Blur the edges of a photo to emphasize the subjects in
the center.
focus.
5 Press [Shutter] to capture a photo.
• Depending on the option you select, the resolution may change to
or
smaller automatically.
] and then select Open
• To apply filter effects to saved photos, press [
Image → an image.
Using the Movie Filter mode
Apply various filter effects to your videos to create unique images. This mode is
available only when you insert a memory card into the camera.
1 On the Home screen, scroll to <Scene>.
2 Select .
3 Select an effect.
Option
Miniature
Vignetting
Half Tone Dot
Extended functions 53
Description
Apply a tilt-shift effect to make the subject appear in
miniature.
Apply the retro-looking colors, high contrast, and strong
vignette effect of Lomo cameras.
Apply a halftone effect.
Using Scene modes
Option
Description
Using the Split Shot mode
Sketch
Apply a pen sketch effect.
Blacken the edges of the frame and distort objects to
imitate the visual effect of a fisheye lens.
Apply a black and white effect.
Apply a sepia tone effect.
Create a vivid look with sharp contrast and strong color.
Make scenes clean and clear.
Apply a soft brown tone.
Create a cold and monotone effect.
In Split Shot mode, you can capture several photos and arrange them with
preset layouts.
Fish-eye
Classic
Retro
Palette Effect 1
Palette Effect 2
Palette Effect 3
Palette Effect 4
4 Press [Shutter] to start recording.
5 Press [Shutter] again to stop recording.
1 On the Home screen, scroll to <Scene>.
2 Select .
3 Select a split style.
• To adjust the sharpness of the dividing line, press [
], and then
select Line Blur → a value.
], and then
• To apply a Smart Filter effect to part of the shot, press [
select Smart Filter → an option. You can apply different Smart Filter effects
to each part of the shot.
• If you select Miniature, playback speed will increase.
• If you select Miniature, you cannot record sound in the video.
• Depending on the option you select, the recording resolution may change to
or smaller automatically.
Panel off
Extended functions 54
Using Scene modes
4 Align your subject in the frame, and then half-press [Shutter] to
focus.
5 Press [Shutter] to capture a photo.
• Repeat steps 4 and 5 to capture the rest of the photos.
• To recapture a photo, press [ ].
The resolution is set to
or smaller.
Using the Motion Photo mode
In Motion Photo mode, you can capture and combine a series of photos, and then
select an area to be animated to create a GIF animation. This mode is available only
when you insert a memory card into the camera.
1 On the Home screen, scroll to <Scene>.
2 Select .
3 Align your subject in the frame, and then half-press [Shutter] to
focus.
4 Press [Shutter] to capture the photo.
• The camera captures multiple photos while the status lamp is blinking.
5 Press [
/
/ /
] to scroll to an area to be animated.
• To recapture a photo, press [
Extended functions 55
].
Using Scene modes
6 Rotate [Zoom] to the left or right to reduce or enlarge the area.
Frame Size
Cancel
7 Press [
Save
] to save the photo.
• The resolution is automatically set to
.
• Use a tripod to prevent your camera from shaking.
• It may take longer to save files.
Extended functions 56
Shooting options
Learn how to set the options in Shooting mode.
Selecting a resolution and quality … …………… 58
Selecting a resolution … ………………………… 58
Selecting a photo quality … ……………………… 59
Using the timer … ………………………………… 60
Shooting in the dark … …………………………… 61
Preventing red-eye … …………………………… 61
Setting a flash option …………………………… 61
Adjusting the ISO sensitivity ……………………… 63
Changing the camera’s focus ……………………… 64
Using macro … …………………………………… 64
Using auto focus … ……………………………… 64
Adjusting the focus area … ……………………… 65
Using Face Detection … …………………………… 67
Detecting faces … …………………………………
Capturing a smile shot … …………………………
Detecting eye blinking ……………………………
Tips for detecting faces ……………………………
67
67
68
68
Adjusting brightness and color …………………… 69
Adjusting the exposure manually (EV) ……………
Compensating for backlighting (ACB) … …………
Changing the metering option ……………………
Selecting a White Balance setting …………………
69
70
70
71
Using burst modes … ………………………………
Adjusting images …………………………………
Reducing the sound of the zoom …………………
Available shooting options by shooting mode ……
73
74
75
76
Selecting a resolution and quality
Learn how to change the image resolution and quality settings.
Selecting a resolution
Setting the video resolution
As you increase the resolution, your photo or video will include more pixels, so it
can be printed on larger paper or displayed on a larger screen. When you use a high
resolution, the file size will also increase.
Setting the photo resolution
1 In Shooting mode, press [
2 Select Photo Size.
3 Select an option.
Icon
1 In Shooting mode, press [
2 Select Movie Size.
3 Select an option.
Icon
].
].
Description
1280 X 720: HD files to play back on an HDTV.
640 X 480: SD files to play back on an analog TV.
320 X 240: Post on a web page.
Description
For Sharing: Post on a website using the wireless network
(30 seconds maximum).
4608 X 3456: Print on A1 paper.
4608 X 3072: Print on A1 paper in wide ratio (3:2).
4608 X 2592 : Print on A1 paper in panorama ratio (16:9) or play
back on an HDTV.
3648 X 2736: Print on A2 paper.
2592 X 1944: Print on A4 paper.
1984 X 1488: Print on A5 paper.
1920 X 1080: Print on A5 paper in panorama ratio (16:9) or play
back on an HDTV.
1024 X 768: Attach to an email.
Shooting options 58
Selecting a resolution and quality
Selecting a photo quality
Set a photo quality setting. Higher image quality settings will result in larger file
sizes. The camera compresses and saves the photos you capture in the JPEG format.
1 In Shooting mode, press [
2 Select Quality.
3 Select an option.
Icon
].
Description
Super Fine: Capture photos in super high quality.
Fine: Capture photos in high quality.
Normal: Capture photos in normal quality.
Shooting options 59
Using the timer
Learn how to set the timer to delay shooting.
1 In Shooting mode, press [
3 Press [Shutter] to start the timer.
].
• The AF-assist light/timer lamp blinks. The camera will automatically capture a
photo after the specified time has elapsed.
Timer
• Press [Shutter] or [ ] to cancel the timer.
• Depending on the Face Detection options you selected, the timer function may
not be available.
• Timer options are not available if you set burst options.
• In some modes, you can also set the timer option by pressing [
], and
then selecting Timer.
Off
10 Sec
2 Sec
Double
Exit
Select
2 Select an option.
Icon
Description
Off: The timer is not active.
10 Sec: Capture a photo after a 10-second delay.
2 Sec: Capture a photo after a 2-second delay.
Double: Capture one photo after a 10-second delay and another
photo after a 2-second delay.
Available options may differ depending on the shooting conditions.
Shooting options 60
Shooting in the dark
Learn how to capture photos at night or in low light conditions.
Preventing red-eye
Setting a flash option
When the flash fires when you capture a photo of a person in the dark, a red glow
may appear in the person’s eyes. To prevent this, select Red-eye or Red-eye Fix.
Refer to flash options in “Setting a flash option.”
Use the flash when you capture photos in the dark or when you need more light in
your photos.
1 In Shooting mode, press [
].
Flash
 Before correction
Off
Auto
Red-eye
Fill in
Slow Sync
Red-eye Fix
 After correction
Exit
Select
2 Select an option.
Icon
Shooting options 61
Description
Off:
• The flash will not fire.
• The camera will display the shake warning
when you are
shooting in low light.
Auto: The camera will select a proper flash setting for the scene it
detects in Smart Auto mode.
Auto: The flash will fire automatically when the subject or
background is dark.
Shooting in the dark
Icon
Description
Red-eye:
• The flash will fire twice when the subject or background is dark to
reduce the red-eye effect.
• There is an interval between the 2 bursts of the flash. Do not move
until the flash fires a second time.
Fill in:
• The flash always fires.
• The camera automatically adjusts light intensity.
Slow Sync:
• The flash fires and the shutter stays open longer.
• This option is recommended when you want to capture more
ambient light to reveal more details in the background.
• Use a tripod to prevent your photos from blurring.
• The camera will display the shake warning
when you are
shooting in low light.
Red-eye Fix:
• The flash fires twice when the subject or background is dark. The
camera corrects red-eyes through its advanced software analysis.
• There is an interval between the 2 bursts of the flash. Do not move
until the flash fires a second time.
Available options may differ depending on the shooting conditions.
Shooting options 62
• Flash options are not available if you set burst options or select Blink Detection.
• Make sure that your subjects are within the recommended distance from the
flash. (p. 143)
• If light from the flash is reflected or there is a substantial amount of dust in the
air, tiny spots may appear in your photo.
• In some modes, you can also set the flash option by pressing [
], and
then selecting Flash.
Shooting in the dark
Adjusting the ISO sensitivity
The ISO sensitivity is the measure of a film’s sensitivity to light as defined by the
International Organization for Standardization (ISO). The higher ISO sensitivity you
select, the more sensitive to light your camera becomes. Use a higher ISO sensitivity
to capture better photos and reduce camera shake when not using the flash.
1 In Shooting mode, press [
2 Select ISO.
3 Select an option.
].
• Select
to use an appropriate ISO sensitivity based on the brightness of
the subject and lighting.
Higher ISO sensitivities may result in more image noise.
Shooting options 63
Changing the camera’s focus
Learn how to adjust the camera’s focus to suit the subject and the shooting conditions.
Using macro
Using auto focus
Use macro to capture close-up photos of subjects, such as flowers or insects.
(Refer to "Using auto focus".)
To capture sharp photos, select the appropriate focus option according to your
distance from the subject.
1 In Shooting mode, press [
Focus
Normal (AF)
Macro
Exit
• Try to hold the camera firmly to prevent blurry photos.
• Turn off the flash if the distance to the subject is less than 15.7 in. (40 cm).
Shooting options 64
Select
].
Changing the camera’s focus
2 Select an option.
Icon
Adjusting the focus area
Description
Normal (AF): Focus on a subject farther than 31 in. (80 cm) away.
Farther than 98 in. (250 cm) away when you use the zoom.
Macro: Focus on a subject that is 2-31 in. (5-80 cm) from the camera.
51-98 in. (130-250 cm) when you use the zoom.
Auto Macro:
• Focus on a subject farther than 2 in. (5 cm) away. Farther than
51 in. (130 cm) away when you use the zoom.
• Auto Macro is set automatically in some modes. You cannot set it
manually.
You can get clearer photos by selecting an appropriate focus area according to your
subject's location in the scene.
1 In Shooting mode, press [
2 Select Focus Area.
3 Select an option.
Icon
Description
Center AF: Focus on the center of the frame (suitable when subjects
are located at or near the center).
Multi AF: Focus on one or more of 9 possible areas.
Available options may differ depending on the shooting conditions.
In some modes, you can also set the focus option by pressing [
selecting Focus.
].
Tracking AF: Focus on and track the subject. (p. 66)
], and then
Available shooting options may differ depending on the shooting mode.
Shooting options 65
Changing the camera’s focus
Using tracking auto focus
Tracking AF allows you to track and automatically focus on your subject, even when
you are moving.
].
1 In Shooting mode, press [
2 Select Focus Area → Tracking AF.
3 Focus on the subject you want to track, and then press [
].
• A focus frame appears on the subject and follows the subject as you move
the camera.
Tracking AF
• The white frame means that your camera is tracking the subject.
• When you half-press [Shutter], the green frame means that your subject is in
focus.
• The red frame means that your camera failed to focus.
4 Press [Shutter] to capture the photo.
Shooting options 66
• If you do not select a focus area, the focus frame will appear in the center of the
screen.
• Tracking a subject may fail when:
-- the subject is too small
-- the subject moves excessively
-- the subject is backlit or you are shooting in a dark place
-- colors or patterns on the subject and the background are the same
-- the subject includes horizontal patterns, such as blinds
-- the camera shakes excessively
• When tracking fails, the feature will be reset.
• If the camera fails to track the subject, you must reselect the subject to track.
• If the camera fails to focus, the focus frame will change to red and the focus will
be reset.
• If you use this function, you cannot set Face Detection options, Timer options,
Burst options, and Intelli zoom.
Using Face Detection
If you use Face Detection options, your camera can automatically detect a human face. When you focus on a human face, the camera adjusts the exposure automatically. Use
Blink Detection to detect closed eyes or Smile Shot to capture a smiling face.
Detecting faces
Capturing a smile shot
Your camera automatically detects up to 10 human faces in one scene.
The camera automatically releases the shutter when it detects a smiling face.
].
1 In Shooting mode, press [
2 Select Face Detection → Normal.
].
1 In Shooting mode, press [
2 Select Face Detection → Smile Shot.
3 Compose your shot.
• The camera automatically releases the shutter when it detects a smiling face.
The face nearest the camera or nearest
the center of the scene appears in a
white focus frame and the rest of the
faces appear in gray focus frames.
The closer you are to the subjects, the quicker your camera will detect faces.
When your subject smiles
broadly, your camera can detect
the smile more easily.
Shooting options 67
Using Face Detection
Detecting eye blinking
Tips for detecting faces
If your camera detects closed eyes, it will automatically capture 2 photos in
succession.
• When your camera detects a face, it tracks the detected face automatically.
• Face Detection may not be effective when:
-- the subject is far from the camera (The focus frame will appear orange for Smile
Shot and Blink Detection.)
-- it is too bright or too dark
-- the subject is not facing the camera
-- the subject is wearing sunglasses or a mask
-- the subject’s facial expression changes drastically
-- the subject is backlit or the lighting conditions are unstable
• When you set Face Detection options, the AF area is automatically set to Multi AF.
• Depending on the Face Detection options you selected, some Shooting options
may not be available.
• Depending on the shooting options you selected, Face Detection options may
not be available.
].
1 In Shooting mode, press [
2 Select Face Detection → Blink Detection.
Shooting options 68
Adjusting brightness and color
Learn how to adjust the brightness and color for better image quality.
Adjusting the exposure manually (EV)
Depending on the intensity of the ambient light, your photos may be too bright or
dark. In these cases, you can adjust the exposure to get a better photo.
3 Press [
/
] to adjust the exposure.
• The photo will be brighter as the exposure value increases.
EV : 0
Cancel
 Darker (-)
 Neutral (0)
1 In Shooting mode, press [
2 Select EV.
 Brighter (+)
4 Press [
].
Set
] to save your settings.
• Once you adjust the exposure, the setting will be stored automatically. You
may need to change the exposure value later to avoid overexposure or
underexposure.
• If you cannot decide on an appropriate exposure, select the AEB (Auto
Exposure Bracket) option. The camera will capture 3 consecutive photos, each
with a different exposure: normal, underexposed, and overexposed. (p. 73)
Shooting options 69
Adjusting brightness and color
Compensating for backlighting (ACB)
Changing the metering option
When the light source is behind your subject or there is high contrast between your
subject and the background, your subject is likely to appear dark in the photo. In
this case, set the Auto Contrast Balance (ACB) option.
The metering mode refers to the way in which a camera measures the quantity
of light. The brightness and lighting of your photos will vary depending on the
metering mode you select.
1 In Shooting mode, press [
2 Select Metering.
3 Select an option.
Icon
▲ Without ACB
▲ With ACB
1 In Shooting mode, press [
2 Select ACB.
3 Select an option.
Icon
].
Description
Off: ACB (Auto Contrast Balance) is deactivated.
On: ACB (Auto Contrast Balance) is activated.
• The ACB feature is always on in Smart Auto mode.
• The ACB feature is not available when you set Burst options.
Shooting options 70
].
Description
Multi:
• Your camera divides the frame into several areas, and then
measures the light intensity of each area.
• Suitable for general photos.
Spot:
• Your camera measures only the light intensity at the very center of
the frame.
• If a subject is not in the center of the frame, your photo may be
improperly exposed.
• Suitable for a subject with backlighting.
Center-weighted:
• Your camera averages the meter reading of the entire frame with
emphasis placed on the center.
• Suitable for photos with subjects in the center of the frame.
Adjusting brightness and color
Selecting a White Balance setting
The color of your photo depends on the type and quality of the light source. If you
want the color of your photo to be realistic, select a White Balance setting that
is appropriate for the lighting conditions, such as Auto WB, Daylight, Cloudy, or
Tungsten.
1 In Shooting mode, press [
2 Select White Balance.
3 Select an option.
Icon
].
Description
Auto WB: Automatically set the White Balance based on the lighting
conditions.
Daylight: For outdoor photos on a sunny day.
Cloudy: For outdoor photos on a cloudy day or in shadows.
Fluorescent_H: For shooting under a daylight fluorescent or 3-way
fluorescent light.
Auto WB
Daylight
Fluorescent_L: For shooting under white fluorescent light.
Tungsten: For shooting indoor photos under incandescent bulbs or
halogen lamps.
Custom Set: To use White Balance settings that you define. (p. 72)
Cloudy
Tungsten
Shooting options 71
Adjusting brightness and color
Defining your own White Balance
You can customize the White Balance by capturing a photo of a white surface, such
as a piece of paper, under the lighting conditions in which you intend to capture a
photo. The White Balance feature will help you to match the colors in your photo
with the actual scene.
].
1 In Shooting mode, press [
2 Select White Balance → Custom Set.
3 Aim the lens at a piece of white paper, and then press [Shutter].
Shooting options 72
Using burst modes
It can be difficult to capture photos of fast-moving subjects or capture natural facial expressions and gestures of your subjects in photos. Also, it can be difficult to adjust the
exposure correctly and select a proper light source. In these cases, select one of the burst modes.
Icon
1 In Shooting mode, press [
2 Select Drive.
3 Select an option.
Icon
Description
AEB:
• Capture 3 consecutive photos, each with a different exposure:
normal, underexposed, and overexposed.
• It may take longer to capture the photo. Use a tripod for best
results.
4 Align your subject in the frame, and then half-press [Shutter] to
].
focus.
5 Press and hold [Shutter].
• While you are pressing [Shutter], the camera captures photos
continuously
Description
Single: Capture a single photo. (Single is not a burst option.)
Continuous:
• While you are pressing [Shutter], the camera continuously
captures photos.
• The maximum number of photos depends on the capacity of your
memory card.
Motion Capture: While you are pressing [Shutter], the camera
photos (5 photos per second; maximum of 30
captures
photos).
Shooting options 73
• Available options may differ depending on the shooting conditions.
• When you select Motion Capture, your camera will set the resolution to
and set the ISO sensitivity to Auto.
• Depending on the Face Detection options you selected, some Shooting options
may not be available.
• It may take longer to save the photos depending on the memory card capacity
and performance.
Adjusting images
Adjust the sharpness, contrast, or saturation of your photos.
1 In Shooting mode, press [
2 Select Image Adjust.
3 Select an option.
].
4 Press [
/
Sharpness
–
• Sharpness
• Contrast
• Saturation
+
Contrast
–
Image Adjust
Sharpness
+
Saturation
–
Contrast
Saturation
Cancel
+
Set
5 Press [
] to adjust each value.
Description
Soften the edges on your photos (suitable for editing the
photos on your computer).
Sharpen the edges to improve the clarity of your photos.
(This may also increase the noise in your photos.)
Description
Decrease the color and brightness.
Increase the color and brightness.
Description
Decrease the saturation.
Increase the saturation.
] to save your settings.
Select 0 if you do not want to apply any effects (suitable for printing).
Shooting options 74
Reducing the sound of the zoom
When you use the zoom while recording videos, the camera can record the sound of the zoom. Use the Sound Alive function to reduce the zoom noise.
1 In Shooting mode, press [
2 Select Voice.
3 Select an option.
Icon
].
Description
Sound Alive On: Turn on the Sound Alive function to reduce the
zoom noise.
Sound Alive Off: Turn off the Sound Alive function. The camera can
record the zoom noise.
Mute: Do not record sounds.
• Do not block the microphone when you use the Sound Alive function.
• Recordings made with Sound Alive may differ from actual sounds.
Shooting options 75
Available shooting options by shooting mode
For details about shooting options, refer to "Shooting options". (p. 57)
Resolution
Smart Auto
Program
Smart Movie
Movie
Scene
Live Panorama
Beauty Shot
O
O
O
O
O
-
O
Quality
-
O
-
-
O
-
O
Timer
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
-
O
O
O
O
Flash
ISO sensitivity
Macro
Focus area
Face detection
EV
ACB
Metering
White balance
Drive
Image adjust
Sound Alive
Digital zoom
Intelli zoom
OIS
O: The option is available. Some options may be limited or may not be changeable.
-: The option is not available.
Shooting options 76
Available shooting options by shooting mode
Night Shot
Close-up Shot
Magic Frame
Photo Filter
Movie Filter
Split Shot
Motion Photo
Resolution
O
O
-
O
O
O
-
Quality
O
O
O
O
-
O
-
Timer
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
Flash
ISO sensitivity
Macro
Focus area
Face detection
EV
ACB
Metering
White balance
Drive
Image adjust
Sound Alive
Digital zoom
Intelli zoom
OIS
O: The option is available. Some options may be limited or may not be changeable.
-: The option is not available.
Shooting options 77
Playback/Editing
Learn how to play back photos or videos, and edit photos. Also, learn how to connect your camera to your
computer or TV.
Viewing photos or videos in Playback mode … … 79
Transferring files to the computer … …………… 93
Starting Playback mode … ……………………… 79
Viewing photos … ………………………………… 83
Playing a video … ………………………………… 86
Transferring files to your Windows OS
computer … ……………………………………… 93
Transferring files to your Mac OS computer ……… 94
Editing a photo … ………………………………… 88
Using programs on a computer … ……………… 95
Resizing photos ……………………………………
Rotating a photo … ………………………………
Applying Smart Filter effects ………………………
Adjusting your photos … …………………………
88
88
89
90
Viewing files on a TV … …………………………… 92
Installing i-Launcher … …………………………… 95
Using i-Launcher … ……………………………… 96
Viewing photos or videos in Playback mode
Learn how to play back photos or videos and how to manage files.
Starting Playback mode
Photo file information
View photos or play videos stored in your camera.
1 Press [
].
2 Press [
/
Memory in use
• The most recent file will be displayed.
• If the camera is off, it will turn on and display the most recent file.
] to scroll through files.
• Press and hold [ /
File Information
] to scroll through files quickly.
• If you want to view files stored in the internal memory, remove your memory
card.
• You may not be able to edit or play back files that were captured with other
cameras, due to unsupported sizes (image size, etc) or codecs. Use a computer
or another device to edit or play back these files.
• Photos or videos captured in portrait orientation do not rotate automatically
and are displayed in landscape orientation by the camera and other devices.
Album/Zoom In
Icon
Description
Current file/Total files
Folder name-File name
GIF file
Protected file
To display file information on the screen, press [
Playback/Editing 79
].
Viewing photos or videos in Playback mode
Video file information
Viewing files as thumbnails
Scan thumbnails of files.
In Playback mode, rotate [Zoom] to the left to view thumbnails
(12 at a time). Rotate [Zoom] to the left once more to display more
thumbnails (24 at a time). Rotate [Zoom] to the right to return to
the previous view.
File Information
Album
Play
Icon
Capture
Description
Current file/Total files
Folder name-File name
Current playback time
Menu
Video length
• You can also view files as thumbnails by scrolling to <Album> on the Home
.
screen, and then selecting
Protected file
To display file information on the screen, press [
].
Press [
Playback/Editing 80
/ / / ] to scroll through files.
Viewing photos or videos in Playback mode
Viewing files by category
View files by category, such as date or file type.
1 In Playback mode, rotate [Zoom] to the left.
• You can also view files as thumbnails by scrolling to <Album> on the Home
.
screen, and then selecting
2 Press [
3 Scroll to a desired list, and then press [ ] to open the list.
4 Scroll to a desired file, and then press [ ] to view the file.
] to return to
5 Rotate [Zoom] to the left, and then press [
the previous view.
• If you change the category, it may take some time for the camera to reorganize
files depending on the number of files.
• If you delete a category classified by Date or File Type, all files in the category
will be deleted.
], and then select Filter → a category.
Filter
All
Date
File Type
Back
Icon
Select
Description
All: View files normally.
Date: View files by the date they were saved.
File Type: View files by the file type.
Playback/Editing 81
Viewing photos or videos in Playback mode
Deleting multiple files
You can select multiple files, and then delete them at once.
Protecting a file
Protect a file from accidental deletion.
1 In Playback mode, press [
1 In Playback mode, select a file to protect.
], and then select Protect → On.
2 Press [
3 Repeat steps 1 and 2 to protect additional files.
2 When the pop-up message appears, select Multiple Delete.
3 Scroll to each file you want to delete, and then press [ ].
You cannot resize, delete, or rotate a protected file.
• Press [
Deleting files
Deleting a single file
You can select one file, and then delete it.
You can also delete files in Playback mode by pressing [
selecting Delete → Delete → Yes.
] again to cancel your selection.
4 Press [ ].
5 When the pop-up message appears, select Yes.
Select files to delete in Playback mode.
1 In Playback mode, select a file, and then press [
2 When the pop-up message appears, select Yes.
].
• When in thumbnails view, press [
], select Delete → Select, and then
skip to step 3, or press [ ], select Select, and then skip to step 3.
].
], and then
Playback/Editing 82
Viewing photos or videos in Playback mode
Viewing photos
Deleting all files
You can select all files, and then delete them at once.
1
In Playback mode, press [
Enlarge part of a photo or view photos as a slide show.
].
• When in thumbnails view, press [
], select Delete → Delete All, and
then skip to step 3, or press [ ], select Delete All, and then skip to step 3.
Enlarging a photo
2 Select Delete → Delete All.
3 When the pop-up message appears, select Yes.
In Playback mode, rotate [Zoom] to the right to enlarge a portion of
the photo. Rotate [Zoom] to the left to zoom out.
• All unprotected files are deleted.
Copying files to a memory card
Enlarged area
Copy files from the internal memory to a memory card.
1 In Playback mode, press [
2 Select Copy to Card.
].
Crop
Playback/Editing 83
Viewing photos or videos in Playback mode
To
Viewing panoramic photos
Description
View photos captured in Live Panorama mode.
Move the enlarged area
Press [
Trim the enlarged photo
Press [ ], and then select Yes. (The trimmed photo
will be saved as a new file. The original photo is
retained in its original form.)
/ / / ].
When you view photos that were captured by another camera, the zoom ratio
may differ.
1 In Playback mode, press [
photo.
/
] to scroll to a desired panoramic
• The entire panoramic photo appears on the screen.
2 Press [
].
• The camera automatically scrolls through the photo from left to right for a
horizontal panoramic photo and from top to bottom for a vertical panoramic
photo. The camera then switches to Playback mode.
• While playing back a panoramic photo, press [ ] to pause or resume.
• After you have paused the playback of a panoramic photo, press
/ / / ] to move the photo horizontally or vertically, depending on
[
the direction you moved when capturing the photo.
3 Press [
] to return to Playback mode.
The camera automatically scrolls through the panoramic photo only if the longest
side of the photo is two or more times longer than the shortest side.
Playback/Editing 84
Viewing photos or videos in Playback mode
Viewing animated photos
* Default
Option
Music
View animated GIF files repeatedly that were captured in Motion Photo mode.
1 In Playback mode, press [
2 Press [ ].
/
] to scroll to a desired GIF file.
Effect
• The GIF file plays back repeatedly.
3 Press [
] to return to Playback mode.
Playing a slide show
Apply effects and audio to a slide show of your photos. The slide show function
does not work for videos and GIF files.
1 In Playback mode, press [
2 Select Slide Show Options.
3 Select a slide show effect option.
] to pause the slide show.
] again to resume the slide show.
• Press [ ], and then press [ / ] to stop the slide show and return to Playback
mode.
• Rotate [Zoom] to the left or right to adjust the volume level.
• Skip to step 4 to start a slide show with no effects.
* Default
Option
Description
Play Mode Set whether or not to repeat the slide show. (One Play*, Repeat)
Interval
Set background audio.
• Set a scene change effect between photos. (Off, Calm*, Shine,
Relax, Lively, Sweet)
• Select Off to cancel effects.
• When you use the Effect option, the interval between photos
will be set to 1 second.
].
4 Press [
5 Select Start Slide Show.
6 View the slide show.
• Press [
• Press [
].
Description
• Set the interval between photos. (1 sec*, 3 sec, 5 sec, 10 sec)
• You must set the Effect option to Off to set the interval.
Playback/Editing 85
Viewing photos or videos in Playback mode
Playing a video
To
Description
In Playback mode, you can view a video, and then capture or trim parts of the
playing video. You can save the captured or trimmed segments as new files.
Scan backward
Press [ ]. Each time you press [ ], you change the scan
speed in this order: 2X, 4X, 8X.
Pause or resume
playback
Press [
Scan forward
Press [ ]. Each time you press [ ], you change the
scan speed in this order: 2X, 4X, 8X.
Adjust the volume
level
Rotate [Zoom] to the left or right.
1 In Playback mode, select a video, and then press [
2 View the video.
].
Current playback time/
Video length
].
When playing a movie, you can begin using features such a scanning backward,
scanning forward, or pausing after the video has run for 2 seconds.
Pause
Stop
Playback/Editing 86
Viewing photos or videos in Playback mode
Trimming a video
Capturing an image from video
].
1 In Playback mode, select a video, and then press [
2 Select Trim Movie.
3 Press [ ] to start playing the video.
4 Press [ ] → [ ] at the point where you want the trimming to
1 While viewing a video, press [
capture an image.
2 Press [
] at the point where you want to
].
• The resolution of the captured image will be the same as the original video.
• The captured image is saved as a new file.
begin.
5 Press [ ] to resume playing the video.
6 Press [ ] → [ ] at the point where you want the trimming to end.
7 Press [ ] to trim.
8 When the pop-up message appears, select Yes.
• The original video should be at least 10 seconds long.
• The camera will save the edited video as a new file and leave the original video
intact.
Playback/Editing 87
Editing a photo
Learn how to edit photos.
• The camera will save edited photos as new files.
• When you edit photos, the camera will automatically convert them to a lower resolution. Photos that you rotate manually are not automatically converted to a lower resolution.
• Photos captured in some modes cannot be edited.
Resizing photos
Rotating a photo
Change the size of a photo and save it as a new file.
1 In Playback mode, select a photo, and then press [
2 Select Resize.
3 Select an option.
].
Resize
2592 X 1944
1 On the Home screen, scroll to <Album>.
2 Select .
3 Rotate [Zoom] to the left, and then select a photo.
4 Select Rotate → an option.
5 Press [ ] to save.
1984 X 1488
1024 X 768
Rotate : Right 90˚
Back
Select
Cancel
Available resize options differ depending on the original size of the photo.
Save
• The camera will overwrite the original file.
], and then select Rotate to rotate a photo.
• In Playback mode, press [
Playback/Editing 88
Editing a photo
Applying Smart Filter effects
Option
Apply special effects to your photos.
Ink Painting
1 On the Home screen, scroll to <Album>.
2 Select .
3 Rotate [Zoom] to the left, and then select a photo.
4 Select Smart Filter → an option.
Oil Painting
Apply a watercolor painting effect.
Apply an oil painting effect.
Apply a cartoon painting effect.
Cartoon
Add lines that radiate outward from bright objects to imitate
Cross Filter
the visual effect of a cross filter.
Apply a pen sketch effect.
Sketch
Hide facial imperfections or apply dreamy effects.
Soft Focus
Blacken the edges of the frame and distort objects to imitate
Fish-eye
the visual effect of a fisheye lens.
Apply a vintage film effect.
Old Film
Half Tone Dot Apply a halftone effect.
Apply a black and white effect.
Classic
Apply a sepia tone effect.
Retro
Blur the edges of a photo to emphasize the subjects in the
Zooming Shot
center.
Smart Filter : Normal
Back
Set
Option
Description
Normal
No effect
Apply a tilt-shift effect to make the subject appear in
miniature. (The top and bottom of the image will be unclear.)
Apply the retro-looking colors, high contrast, and strong
vignette effect of Lomo cameras.
Miniature
Vignetting
Description
5 Press [
Playback/Editing 89
] to save.
Editing a photo
Adjusting your photos
Learn how to adjust the brightness, contrast, or saturation or how to correct the
red-eye effect. If the center of a photo is dark, you can adjust it to be brighter.
The camera will save an edited photo as a new file, but may convert it to a lower
resolution.
• You can adjust brightness, contrast, and saturation and apply Smart Filter
effects at the same time.
• You cannot apply the ACB, Face Retouch, and Red-eye Fix effects at the same
time.
Adjusting brightness, contrast, or saturation
1 On the Home screen, scroll to <Album>.
2 Select .
3 Rotate [Zoom] to the left, and then select a photo.
4 Select an adjusting option.
Icon
5 Press [
6 Press [
7 Press [
/
] to adjust the option.
].
] to save.
Adjusting dark subjects (ACB)
1 On the Home screen, scroll to <Album>.
2 Select .
3 Rotate [Zoom] to the left, and then select a photo.
4 Select ACB.
5 Press [ ] to save.
Description
Brightness
Contrast
Saturation
Playback/Editing 90
Editing a photo
Retouching faces
1 On the Home screen, scroll to <Album>.
2 Select .
3 Rotate [Zoom] to the left, and then select a photo.
4 Select Face Retouch.
5 Press [ / ] to adjust the option.
• As the number increases, the skin tone becomes brighter and smoother.
6 Press [
] to save.
Removing red-eye
1 On the Home screen, scroll to <Album>.
2 Select .
3 Rotate [Zoom] to the left, and then select a photo.
4 Select Red-eye Fix.
5 Press [ ] to save.
Playback/Editing 91
Viewing files on a TV
Play back photos or videos by connecting your camera to a TV with the A/V cable.
1 On the Home screen, scroll to <Basic>.
2 Select .
3 Select Connectivity → Video Out.
4 Select the video signal output for your country or region. (p. 124)
5 Turn off your camera and TV.
6 Connect your camera to your TV with the A/V cable.
Audio
7 Turn on your TV, and then select the A/V video source with the
TV remote control.
8 Turn on your camera.
• The camera automatically enters into Playback mode when you connect
it to a TV.
9 View photos or play videos using the camera buttons.
Video
Playback/Editing 92
• Depending on the TV model, you may see some digital noise or part of an
image may not appear.
• Images may not be centered on the TV screen depending on your TV settings.
Transferring files to the computer
Connect the camera to a computer to transfer files from the camera's memory card to the computer.
6 Turn on the camera.
Transferring files to your Windows OS computer
• The computer recognizes the camera automatically.
Connect the camera to your computer as a removable disk.
7 On your computer, select My Computer → Removable Disk →
Your computer must be running Windows XP, Windows Vista, Windows 7, or
Windows 8 for you to connect the camera as a removable disk.
DCIM → 100PHOTO.
8 Drag or save files to your computer.
1 On the Home screen, scroll to <Basic>.
2 Select .
3 Select Connectivity → i-Launcher → Off.
4 Turn off the camera.
5 Connect the camera to your computer with the USB cable.
Disconnecting the camera (for Windows XP)
With Windows Vista, Windows 7 and Windows 8, the methods for disconnecting
the camera are similar.
You must plug the small end of the USB cable into your camera. If the cable
is reversed, it may damage your files. The manufacturer is not responsible for
any loss of data.
1 If the status lamp on your camera is blinking, wait until it stops.
2 Click on the tool bar at the bottom right of your computer
screen.
3 Click the pop-up message.
4 Click the message box that indicates the camera can be removed
safely.
5 Remove the USB cable.
Playback/Editing 93
Transferring files to the computer
Transferring files to your Mac OS computer
When you connect the camera to your Mac OS computer, the computer will
automatically recognize the device. You can transfer files directly from the
camera to the computer without installing any programs.
Mac OS 10.5 or later is supported.
3 Turn on the camera.
• The computer recognizes the camera automatically and displays a
removable disk icon.
4 Open the removable disk.
5 Drag or save files to your computer.
1 Turn off the camera.
2 Connect your camera to your Mac OS computer with the USB
cable.
You must plug the small end of the USB cable into your camera. If the cable
is reversed, it may damage your files. The manufacturer is not responsible for
any loss of data.
Playback/Editing 94
Using programs on a computer
i-Launcher allows you to play back files with Multimedia Viewer and provides links so that you can download useful programs.
6 Turn on the camera.
7 When the pop-up window prompts you to install i-Launcher,
Installing i-Launcher
1 On the Home screen, scroll to <Basic>.
2 Select .
3 Select Connectivity → i-Launcher → On.
4 Turn off the camera.
5 Connect the camera to your computer with the USB cable.
select Yes.
• If a pop-up window prompting you to run iLinker.exe appears, run it first.
• When you connect the camera to a computer with i-Launcher installed,
the program will launch automatically.
8 Follow the on-screen instructions to complete the installation.
• An i-Launcher shortcut will appear on the computer.
You must plug the small end of the USB cable into your camera. If the cable
is reversed, it may damage your files. The manufacturer is not responsible for
any loss of data.
Playback/Editing 95
• Before installing the program, ensure that the PC is connected to a network.
• To install i-Launcher on your Mac OS computer, click Devices → i-Launcher →
Mac → iLinker.
Using programs on a computer
Available programs when using i-Launcher
Windows OS Requirements
Option
Description
Item
Multimedia Viewer
You can view files with Multimedia Viewer.
You can update the firmware of your camera.
i-Launcher provides a link for downloading the PC
Auto Backup program when you connect the camera
to a computer. You can send photos or videos that you
captured with the camera to a PC wirelessly.
Firmware Upgrade
PC Auto Backup
If you use a Mac OS computer, only Firmware Upgrade and PC Auto Backup are
available.
CPU
RAM
OS*
Minimum 512 MB RAM (1 GB or more recommended)
Windows XP SP2, Windows Vista, Windows 7, or Windows 8
Hard disk
capacity
250 MB or more (1 GB and above recommended)
Others
• 1024 X 768 pixels, 16-bit color display compatible monitor
(1280 X 1024 pixels, 32-bit color display recommended)
• USB 2.0 port
• nVIDIA Geforce 7600GT or higher/
ATI X1600 series or higher
• Microsoft DirectX 9.0c or higher
Using i-Launcher
i-Launcher allows you to play back files with Multimedia Viewer and provides a
link to download the PC Auto Backup program.
Requirements
Intel Pentium®4, 3.2 GHz or higher/
AMD Athlon™ FX D2.6 GHz or higher
*A 32-bit version of i-Launcher will be installed—even on 64-bit editions of Windows XP,
Windows Vista, Windows 7, and Windows 8.
• The requirements are recommendation only. i-Launcher may not work properly
even when the computer meets the requirements, depending on the condition
of your computer.
• If your computer does not meet the requirements, videos may not play
correctly.
The manufacturer is not responsible for any damage that results from using
unqualified computers such as a computer you assembled yourself.
Playback/Editing 96
Using programs on a computer
Mac OS requirements
Item
OS
Requirements
Mac OS 10.5 or higher (except PowerPC)
RAM
Minimum 256 MB RAM (512 MB or more recommended)
Hard disk
capacity
Minimum 110 MB
Others
USB 2.0 port
Opening i-Launcher
On your computer, select Start → All Programs → Samsung → i-Launcher →
Samsung i-Launcher. On your Mac, click Applications → Samsung → i-Launcher.
Playback/Editing 97
Using programs on a computer
Using Multimedia Viewer
Multimedia Viewer allows you to play back files. From the Samsung i-Launcher screen, click Multimedia Viewer.
• Multimedia Viewer supports the following formats:
-- Videos: MP4 (Video: H.264, Audio: AAC), WMV (WMV 7/8/9), AVI (MJPEG)
-- Photos: JPG, GIF, BMP, PNG, TIFF, MPO
• Files that have been recorded with other manufacturers’ devices may not play back smoothly.
Viewing photos
1
2
3
!
0
9 8
7
6
5 4
Playback/Editing 98
No.
1
2
3
4
5
6
7
8
9
0
!
Description
File name
Enlarged area
Histogram
Open the selected file.
Histogram button
Rotate to the left/ Rotate to the right.
Move to the previous file/ Move to the next file.
Fit the photo to the screen.
View the photo in its original size.
Zoom in/Zoom out
Switches between 2D and 3D mode.
Using programs on a computer
Viewing videos
1
No.
1
2
3
4
5
6
7
8
2
8
7 6 5 4
3
Playback/Editing 99
Description
File name
Adjust the volume.
Open the selected file.
Move to the next file.
Stop
Pause
Move to the previous file.
Progress bar
Using programs on a computer
Updating the firmware
From the Samsung i-Launcher screen, click Firmware Upgrade.
Downloading the PC Auto Backup program
From the Samsung i-Launcher screen, click PC Auto Backup. For information about
installing the PC Auto Backup program, refer to page 110.
Playback/Editing 100
Wireless network
Learn how to connect to wireless local area networks (WLANs) and use functions.
Connecting to a WLAN and configuring
network settings …………………………………… 102
Connecting to a WLAN … ………………………… 102
Using the login browser … ……………………… 103
Network connection tips … ……………………… 104
Entering text … …………………………………… 105
Saving files to a smart phone automatically … …
Sending photos or videos to a smart phone … …
Using a smart phone as a remote shutter
release … ……………………………………………
Using Auto Backup to send photos or videos ……
Sending photos or videos via email ……………… 112
Changing email settings … ……………………… 112
Sending photos or videos via email … …………… 114
Using photo or video sharing websites … ……… 115
Accessing a website … …………………………… 115
Uploading photos or videos ……………………… 115
106
Using AllShare Play to send files … ……………… 117
107
Uploading photos to online storage ……………… 117
Viewing photos or videos on devices that
support AllShare Play … ………………………… 118
108
110
Installing the program for Auto Backup on
your PC … ………………………………………… 110
Sending photos or videos to a PC ………………… 110
Sending photos using Wi-Fi Direct … …………… 120
Connecting to a WLAN and configuring network settings
Learn to connect via an access point (AP) when you are in a range of a WLAN. You can also configure network settings.
Connecting to a WLAN
Icon
1 On the Home screen, scroll to <Wi-Fi>.
2 Select , , , or .
], and then select Wi-Fi Setting.
3 Press [
Secured AP
WPS AP
Signal strength
• In some modes, follow the on-screen instructions until the Wi-Fi Setting
screen appears.
• The camera automatically searches for available AP devices.
Press [
] to open network setting options.
• When you select a secured AP, a pop-up window appears. Enter the
required passwords to connect to the WLAN. For information about
entering text, refer to "Entering text". (p. 105)
• When a login page appears, refer to "Using the login browser". (p. 103)
• When you select an unsecured AP, the camera will connect to the WLAN.
• If you select a WPS profile supported AP, select → WPS PIN connection,
and then enter a PIN on the AP device. You can also connect to a WPS
profile supported AP by selecting → WPS button connection on the
camera, and then pushing the WPS button on the AP device.
4 Select an AP.
Wi-Fi Setting
Refresh
Samsung 1
Samsung 2
Samsung 3
Samsung 4
Back
Description
Ad hoc AP
Manual
• Select Refresh to refresh connectable APs.
• Select Add wireless network to add an AP manually. Your AP name must
be in English to add the AP manually.
Wireless network 102
Connecting to a WLAN and configuring network settings
Using the login browser
Setting network options
1 In the Wi-Fi Setting screen, move to an AP, and then press [
2 Select each option, and then enter the required information.
Option
].
Description
Network Password
Enter the network password.
IP Setting
Set the IP address automatically or manually.
You can enter your login information via the login browser when connecting to
some APs, sharing sites, or cloud servers.
Button/Icon
Description
[
[
Move to an item or scroll the page.
Select an item.
Access the following options:
• Previous Page: Move to the previous page.
• Next Page: Move to the next page.
• Reload: Reload the page.
• Stop: Stop loading the page.
• Exit: Close the login browser.
Close the login browser.
/ / / ]
]
[
Manually setting the IP address
1 In the Wi-Fi Setting screen, move to an AP, and then press [
2 Select IP Setting → Manual.
3 Select each option, and then enter the required information.
Option
Description
IP
Enter the static IP address.
Subnet Mask
Enter the subnet mask.
Gateway
Enter the gateway.
Enter the DNS address.
DNS Server
].
[ ]
]
• You may not be able to select some items depending on the page you
connected to. This does not indicate a malfunction.
• The login browser may not close automatically after you log into some pages.
In this case, close the login browser by pressing [ ], and then proceed with the
desired operation.
• It may take longer to load the login page due to the page size or network speed.
If this occurs, wait until the login information input window appears.
Wireless network 103
Connecting to a WLAN and configuring network settings
Network connection tips
• You must insert a memory card to use the Wi-Fi features.
• The quality of the network connection will be determined by the AP.
• The further the distance between your camera and the AP, the longer it will take
to connect to the network.
• If a nearby device is using the same radio frequency signal as your camera, it may
interrupt your connection.
• If your AP name is not in English, the camera may not be able to locate the device
or the name may appear incorrectly.
• For network settings or a password, contact your network administrator or
network service provider.
• If a WLAN requires authentication from the service provider, you may not be able
to connect to it. To connect the WLAN, contact your network service provider.
• Depending on the encryption type, the number of digits in the password may
differ.
• A WLAN connection may not be possible in all surroundings.
• The camera may display a WLAN enabled printer on the AP List. You cannot
connect to a network via a printer.
• You cannot connect your camera to a network and a TV simultaneously.
• Connecting to a network may incur additional charges. Costs will vary based on
the conditions of your contract.
• If you cannot connect to a WLAN, try another AP from the available AP list.
• A login page may appear when you select free WLANs provided by some
network service providers. Enter your ID and password to connect to the WLAN.
For information about registering or the service, contact the network service
providers.
• Be cautious when you enter personal information for an AP connection. Do not
enter any payment or credit card information on your camera. The manufacturer
is not liable for any problem caused by entering such information.
• Available network connections may differ by country.
• The WLAN feature of your camera must comply with radio transmission laws in
your region. To ensure compliance, use the WLAN feature only in the country
where you purchased the camera.
• The process for adjusting network settings may differ, depending on network
conditions.
• Do not access a network that you are not authorized to use.
• Before you connect to a network, ensure your battery is fully charged.
• You cannot upload or send files captured in some modes.
• Files that you transfer to another device may not be supported by the device. In
this case, use a computer to playback the files.
Wireless network 104
Connecting to a WLAN and configuring network settings
Entering text
Icon
Description
Learn how to enter text. The icons in the table below let you move the cursor,
/ / / ] to move to a desired key, and then press
change the case, etc. Press [
[ ] to enter the key.
Switch between Symbol mode and ABC mode.
Enter a space.
Done
Save the displayed text.
View the entering text guide.
• You can use only the English alphabets in some modes, regardless of the display
language.
• To move to Done directly, press [ ].
• You can enter up to 64 characters.
• The screen may differ depending on the input mode.
Done
Cancel
Icon
Backspace
Description
Delete the last letter.
Move the cursor.
In ABC mode, change the case.
Enter ".com".
Wireless network 105
Saving files to a smart phone automatically
The camera connects to a smart phone that supports the AutoShare feature via a WLAN. When you capture a photo with your camera, the photo is saved to the smart phone
automatically.
• The AutoShare feature is supported by Galaxy series smart phones or Galaxy Tab models with the Android 2.2 OS or higher or iOS devices with the iOS 4.3 or higher. Before using this
feature, check the device’s firmware and update it if needed.
• You should install the Samsung SMART CAMERA App on your phone or device before using this feature. You can download the application from Samsung Apps, Google Play Store, or
Apple App Store. The Samsung SMART CAMERA App is compatible with Samsung camera models manufactured in 2013 or later.
• If you set this function, the setting is maintained even when you change the Shooting mode.
• This feature may not be supported in some modes.
1 On the camera, in Shooting mode, press [
2 On the camera, select AutoShare → On.
5 On the camera, allow the smart phone to connect to your
].
camera.
• If the pop-up message that prompts you to download the application
appears, select Next.
3 On the smart phone, turn on the Samsung SMART CAMERA App.
• For iOS devices, turn on the Wi-Fi feature before turning on the
application.
4
Select the camera from the list and connect the smart phone to
the camera.
• The smart phone can connect to only one camera at a time.
• If the smart phone has been connected to your camera before, it is
connected automatically.
• An icon that shows the connection status ( ) will appear on the
camera’s screen.
6 On the camera, capture a photo.
• The captured photo is saved to the camera, and then transferred to the
smart phone.
• If you recorded a video, it is saved only to the camera.
• A GIF file captured in the motion capture mode is not saved on the smart
phone.
Wireless network 106
Sending photos or videos to a smart phone
The camera connects to a smart phone that supports the MobileLink feature via a WLAN. You can easily send photos or videos to your smart phone.
• The MobileLink feature is supported by Galaxy series smart phones or Galaxy Tab models with the Android 2.2 OS or higher or iOS devices with the iOS 4.3 or higher. Before using this
feature, check the device’s firmware and update it if needed.
• You should install the Samsung SMART CAMERA App on your phone or device before using this feature. You can download the application from Samsung Apps, Google Play Store, or
Apple App Store. The Samsung SMART CAMERA App is compatible with Samsung camera models manufactured in 2013 or later.
• When there are no files in the camera memory, you cannot use this feature.
• If you select files from the smart phone, you can view up to 1,000 recent files and send up to 150 files at a time. If you select files from the camera, you can view files that were
selected from the camera and the maximum number of files that can be send varies depending on the storage space of the smart phone.
1 On the camera’s Home screen, scroll to <Wi-Fi>.
2 On the camera, select .
5 Select the camera from the list and connect the smart phone to
the camera.
• The smart phone can connect to only one camera at a time.
• If the pop-up message that prompts you to download the application
appears, select Next.
6 On the camera, allow the smart phone to connect to your
camera.
3 On the camera, select a sending option.
• If you select Select Files from Smartphone, you can use your smart
phone to view and share files stored on the camera.
• If you select Select Files from Camera, you can select files to send from
the camera.
4
On the smart phone, turn on the Samsung SMART CAMERA App.
• For iOS devices, turn on the Wi-Fi feature before turning on the
application.
• If the smart phone has been connected to your camera before, it is
connected automatically.
7 On the smart phone or camera, select files to transfer from the
camera.
8 On the smart phone, touch the copy button or on the camera,
select Share.
• The camera will send the files.
Wireless network 107
Using a smart phone as a remote shutter release
The camera connects to a smart phone via a WLAN. Use the smart phone as a remote shutter release with the Remote Viewfinder feature. The captured photo will display on the
smart phone.
• The Remote Viewfinder feature is supported by Galaxy series smart phones or Galaxy Tab models with the Android 2.2 OS or higher or iOS devices with the iOS 4.3 or higher. Before
using this feature, check the device’s firmware and update it if needed.
• You should install the Samsung SMART CAMERA App on your phone or device before using this feature. You can download the application from Samsung Apps, Google Play Store, or
Apple App Store. The Samsung SMART CAMERA App is compatible with Samsung camera models manufactured in 2013 or later.
1 On the camera’s Home screen, scroll to <Wi-Fi>.
2 On the camera, select .
6 On the smart phone, set the following shooting options.
Icon
• If the pop-up message that prompts you to download the application
appears, select Next.
Flash option
Timer option
3 On the smart phone, turn on the Samsung SMART CAMERA App.
Photo size
• For iOS devices, turn on the Wi-Fi feature before turning on the
application.
Saving location
4 Select the camera from the list and connect the smart phone to
Zoom ratio
the camera.
• The smart phone can connect to only one camera at a time.
5 On the camera, allow the smart phone to connect to your
camera.
• If the smart phone has been connected to your camera before, it is
connected automatically.
Description
• While using this feature, some buttons are not available on your camera.
• The zoom button and the shutter button on your smart phone will not
function when using this feature.
and
photo sizes only.
• Remote Viewfinder mode supports the
Wireless network 108
Using a smart phone as a remote shutter release
7 On the smart phone, touch and hold
to focus.
• The focus is automatically set to Multi AF.
8 Release
to capture the photo.
• The photo will be resized to 640 X 360 when it is stored to the smart
phone.
• When you use this feature, the ideal distance between the camera and the
smart phone may vary, depending on your surroundings.
• The smart phone must be within 7 m of the camera to use this feature.
• It will take some time to capture the photo after you release
on the smart
phone.
• The Remote Viewfinder function will deactivate when:
-- there is an incoming call on the smart phone
-- either the camera or the smart phone turn off
-- the memory is full
-- either device loses its connection to the WLAN
-- the Wi-Fi connection is poor or unstable
Wireless network 109
Using Auto Backup to send photos or videos
You can send photos or videos that you captured with the camera to a PC wirelessly.
Installing the program for Auto Backup on your PC
Sending photos or videos to a PC
1 Install i-Launcher on the PC. (p. 95)
2 Connect the camera to the PC with the USB cable.
3 When the Auto Backup program icon appears, click it.
1 On the Home screen, scroll to <Wi-Fi>.
2 Select .
• The Auto Backup program is installed on the PC and the information
about the PC will be stored to the camera. Follow the on-screen
instructions to complete the installation.
• You can also store the information about the PC to the camera by
connecting the PC and the camera via Wi-Fi.
4 Remove the USB cable.
Before installing the program, ensure that the PC is connected to a network.
• If the the pop-up message that prompts you to download the application
appears, select Next.
• You must configure the backup PC information to use the Auto Backup
feature. For more details, refer to “Installing the program for Auto Backup on
your PC”. (p. 110) If the Auto Backup program is installed on your PC, save the
PC information via USB cable or Wi-Fi connection.
• The camera will automatically attempt to connect to a WLAN via the most
recently connected AP device.
• If the camera has not previously been connected to a WLAN, it will search for
available AP devices. (p. 102)
Wireless network 110
Using Auto Backup to send photos or videos
3 Select a backup PC.
• If you have performed a backup before, skip to step 4.
4 Select OK.
• To cancel sending, select Cancel.
• You cannot select individual files to backup. This function backs up only
new files on the camera.
• The backup's progress will be shown on the PC monitor.
• When the transfer is completed, the camera will turn off automatically in
approximately 30 seconds. Select Cancel to return to the previous screen
and prevent the camera from turning off automatically.
• To turn off your PC automatically after the transfer is complete, press
], and then select Shut down PC after backup → On.
[
• To change the backup PC, select Change PC.
Wireless network 111
• When you connect the camera to the WLAN, select the AP that is connected to
the PC.
• The camera will search for available access points even if you are connecting to
the same access point again.
• If you turn off the camera or remove the battery while sending files, the file
transfer will be interrupted.
• While you are using this feature, the shutter control is disabled on your camera.
• You can connect only one camera to the PC at a time for sending files.
• The backup may be canceled due to network conditions.
• Photos or videos can be sent to a PC one time only. Files cannot be sent again
even if you reconnect your camera to another PC.
• When there are no files in the camera memory, you cannot use this feature.
• You must turn off Windows Firewall and any other firewalls before using this
feature.
• You can send up to 1,000 recent files.
• On the PC software, the server name must be entered in the Latin alphabet and
can contain no more than 48 characters.
• When multiple file types are created at once, only the image files (JPG) will be
sent to the PC with this feature.
Sending photos or videos via email
You can change settings in the email menu and send photos or videos stored on the camera via email.
Changing email settings
In the email menu, you can change settings for storing your information. You can
also set or change the email password. For information about entering text, refer to
"Entering text". (p. 105)
5 Select the Name box, enter your name, and then select Done.
Sender Setting
Name
Storing your information
Email
1 On the Home screen, scroll to <Wi-Fi>.
2 Select .
Save
• The camera will automatically attempt to connect to a WLAN via the most
recently connected AP device.
• If the camera has not previously been connected to a WLAN, it will search for
available AP devices. (p. 102)
].
3 Press [
4 Select Sender Setting.
Reset
Back
6 Select the Email box, enter your email address, and then select
Done.
7 Select Save to save your changes.
• To delete your information, select Reset.
Wireless network 112
Sending photos or videos via email
Setting an email password
Changing the email password
1 On the Home screen, scroll to <Wi-Fi>.
2 Select .
1 On the Home screen, scroll to <Wi-Fi>.
2 Select .
].
3 Press [
4 Select Setting Password → On.
].
3 Press [
4 Select Change Password.
5 Enter your current 4-digit password.
6 Enter a new 4-digit password.
7 Enter the new password again.
8 When the pop-up appears, select OK.
• The camera will automatically attempt to connect to a WLAN via the most
recently connected AP device.
• If the camera has not previously been connected to a WLAN, it will search for
available AP devices. (p. 102)
• To deactivate the password, select Off.
5
When the pop-up appears, select OK.
• The pop-up disappears automatically even if you do not select OK.
6 Enter a 4-digit password.
7 Enter the password again.
8 When the pop-up appears, select OK.
• The camera will automatically attempt to connect to a WLAN via the most
recently connected AP device.
• If the camera has not previously been connected to a WLAN, it will search for
available AP devices. (p. 102)
If you lost your password, you can reset it by selecting Reset on the password
setting screen. When you reset the information, the previously saved user’s setting
information, email address, and recently sent email list will be deleted.
Wireless network 113
Sending photos or videos via email
Sending photos or videos via email
You can send photos or videos stored on the camera via email. For information
about entering text, refer to "Entering text". (p. 105)
1 On the Home screen, scroll to <Wi-Fi>.
2 Select .
6 Scroll to files to send, and then press [
].
• You can select up to 20 files. The total size must be 7 MB or less.
7 Select Next.
8 Select the Comment box, enter your comments, and then select
Done.
• The camera will automatically attempt to connect to a WLAN via the most
recently connected AP device.
• If the camera has not previously been connected to a WLAN, it will search for
available AP devices. (p. 102)
9 Select Send.
• The camera will send the email.
3 Select the Sender box, enter your email address, and then select
Done.
• If you have previously saved your information, it will be inserted
automatically. (p. 112)
• To use an address from the list of previous senders, select → an
address.
4 Select the Receiver box, enter an email address, and then select
Done.
• To use an address from the list of previous recipients, select → an
address.
• Select to add additional recipients. You can input up to 30 recipients.
• Select to delete an address from the list.
5 Select Next.
Wireless network 114
• Even if a photo appears to have transferred successfully, errors with the
recipient’s email account may cause the photo to be rejected or recognized as
spam.
• You may not be able to send an email if no network connection is available or if
your email account settings are incorrect.
• You cannot send an email if the file size exceeds the limit. The maximum
photo resolution you can send is 2M and the longest video you can upload is
30 seconds at
resolution or a video recorded using . If the selected
photo resolution is higher than 2M, it will be automatically resized to a lower
resolution.
• If you cannot send an email because of firewall or user authentication settings,
contact your network administrator or network service provider.
• When there are no files in the camera memory, you cannot use this feature.
• You can also send an email in Playback mode by pressing [
], and then
selecting Share(Wi-Fi) → Email.
Using photo or video sharing websites
Upload your photos or videos to file sharing websites. Available websites will be displayed on your camera. To upload files to some websites, you must visit the website and
register before connecting your camera.
Accessing a website
Uploading photos or videos
1 On the Home screen, scroll to <Wi-Fi>.
2 Select .
3 Select a website.
1 Access the website with your camera.
2 Scroll to the files you want to upload, and then press [
• If the pop-up message that prompts you to create an account appears, select
OK.
• The camera will automatically attempt to connect to a WLAN via the most
recently connected AP device.
• If the camera has not previously been connected to a WLAN, it will search for
available AP devices. (p. 102)
].
• You can select up to 20 files. The total size must be 10 MB or less.
(On some websites, the total size or number of files may vary.)
3 Select Upload.
• If you connected to Facebook, select Upload → Upload.
• On some websites, you can enter your comments by selecting the
Comment box. For information about entering text, refer to “Entering
text”. (p. 105)
4 Enter your ID and password to log in.
• For information about entering text, refer to "Entering text". (p. 105)
• To select an ID from the list, select → an ID.
• If you have previously logged in to the website, you may be logged in
automatically.
You must have an existing account on the file sharing website to use this feature.
Wireless network 115
Using photo or video sharing websites
• You can set an upload folder for Facebook by pressing [
], and then
selecting Upload Folder (Facebook) on the website's list screen.
• You cannot upload files if the file size exceeds the limit. The maximum photo
resolution you can upload is 2M, and the longest video you can upload is
30 seconds at
resolution or a video recorded using . If the selected
photo resolution is higher than 2M, it will be automatically resized to a lower
resolution. (On some websites, the maximum photo resolution may vary.)
• The method of uploading photos or videos may differ depending on the
selected website.
• If you cannot access a website because of firewall or user authentication
settings, contact your network administrator or network service provider.
• Uploaded photos or videos may be automatically titled with the date they were
captured.
• The speed of your internet connection may affect how quickly photos upload or
web pages open.
• When there are no files in the camera memory, you cannot use this feature.
• You can also upload photos or videos to file sharing websites in Playback mode
by pressing [
], and then selecting Share(Wi-Fi) → a desired website.
• You cannot upload videos to some websites.
Wireless network 116
Using AllShare Play to send files
You can upload files from your camera to AllShare Play online storage or view files on a AllShare Play device connected to the same AP.
3 Enter your ID and password, and then select Login → OK.
Uploading photos to online storage
1 On the Home screen, scroll to <Wi-Fi>.
2 Select → Web storage.
• If the guide message appears, press [ ].
• The camera will automatically attempt to connect to a WLAN via the most
recently connected AP device.
• If the camera has not previously been connected to a WLAN, it will search
for available AP devices. (p. 102)
• To change the size for uploaded photos, press [
], and then select
Upload Image Size.
• If you have registered more than one web storage, you can select from the list
], and then selecting Change Web storage.
by pressing [
• For information about entering text, refer to "Entering text". (p. 105)
• To select an ID from the list, select → an ID.
• If you have previously logged in to the website, you may be logged in
automatically.
To use this feature, you must create an AllShare Play account and an account
with an affiliated online storage service using your PC. After finishing creating
accounts, add your online storage account to AllShare Play.
4 Scroll to the files you want to upload, and then press [
5 Select Upload.
Wireless network 117
•
•
•
•
•
].
If you have registered more than one web storage, select a web storage first.
You cannot upload video files to AllShare Play online storage.
When there are no files in the camera memory, you cannot use this feature.
You can upload up to 20 files.
You can also upload photos in Playback mode by pressing [
], and then
selecting Share(Wi-Fi) → AllShare Play.
Using AllShare Play to send files
Viewing photos or videos on devices that support AllShare Play
1 On the Home screen, scroll to <Wi-Fi>.
2 Select → Nearby Devices.
• If the guide message appears, press [ ].
• The camera will automatically attempt to connect to a WLAN via the most
recently connected AP device.
• If the camera has not previously been connected to a WLAN, it will search for
available AP devices. (p. 102)
• You can set to allow only selected devices or all devices to connect by
], and then selecting DLNA Access Control on the screen.
pressing [
• A sharing file list is created. Wait until other devices can find your camera.
6 On the AllShare Play device, browse the shared photos or videos.
• For information about searching for the camera and browsing the photos
or videos on the AllShare Play device, refer to the device's user manual.
• Videos may not play smoothly depending on the type of AllShare Play
device or the network condition. If this happens, re-record the video in
or smaller quality and play it again. If videos do not play smoothly
on your device over the wireless connection, try connecting the camera
to the device with an A/V cable.
3 Connect the AllShare Play device to a network, and then turn on
the AllShare Play feature.
• Refer to your device's user manual for more information.
4 On the camera, allow the AllShare Play device to connect to your
camera.
5 On the AllShare Play device, select a camera to connect.
AP
▲ A camera is connected to a TV that supports AllShare Play via WLAN.
Wireless network 118
Using AllShare Play to send files
• You can share up to 1,000 recent files.
• On an AllShare Play device, you can view only photos or videos captured with
your camera.
• The range of the wireless connection between your camera and an AllShare
Play device may vary depending on the specifications of the AP.
• If the camera is connected to 2 AllShare Play devices, playback may be slower.
• Photos or videos will be shared in their original sizes.
• You can use this feature only with devices that support AllShare Play.
• Shared photos or videos will not be stored on the AllShare Play device, but they
can be stored in the camera to meet the device's specifications.
• Transferring photos or videos to the AllShare Play device may take some time
depending on the network connection, the number of files to be shared, or the
sizes of the files.
• If you power off the camera abnormally while viewing photos or videos on
an AllShare Play device (for example, by removing the battery), the device
considers the camera to still be connected.
• The order of photos or videos on the camera may be different than on the
AllShare Play device.
Wireless network 119
• Depending on the number of photos or videos you want to share, it may
take some time to load your photos or videos and complete the initial set-up
process.
• While viewing photos or videos on the AllShare Play device, continuously using
the device's remote or performing additional operations on the device may
prevent this feature from working properly.
• If you reorder or sort files on the camera while viewing them on an AllShare Play
device, you must repeat the initial set-up process to update the list of files on
the device.
• When there are no files in the camera memory, you cannot use this feature.
• We recommend you use a network cable to connect your AllShare Play device
to your AP. This will minimize any video ‘Stuttering’ you may experience when
streaming content.
• To view files on an AllShare Play device using the Nearby devices feature,
enable multicast mode on your AP.
Sending photos using Wi-Fi Direct
When the camera connects via a WLAN to a device that supports the Wi-Fi Direct function, you can send photos to the device. This feature may not be supported on some
devices.
1 On the device, turn on the Wi-Fi Direct option.
2 On the camera, in Playback mode, scroll to a photo.
], and then select Share(Wi-Fi) → Wi-Fi Direct.
3 Press [
5 On the device, allow the camera to connect to the device.
• The photo will be sent to the device.
• When in the single image view, you can send only one photo at a time.
• When in the thumbnails view, you can select multiple photos by scrolling
to thumbnails, and then pressing [ ]. Select Next when you are finished
selecting photos.
4 Select the device from the camera’s list of Wi-Fi Direct devices.
• Ensure that the device's Wi-Fi Direct option is turned on.
• You can also select your camera from the device's list of Wi-Fi Direct
devices.
Wireless network 120
• You can send up to 20 files at a time.
• When there are no photos in the camera memory, you cannot use this feature.
• If you cannot connect to a Wi-Fi Direct device, update the device with the latest
firmware. This feature may not be supported on some devices.
Settings
Refer to options to configure your camera’s settings.
Settings menu ……………………………………………………… 122
Accessing the settings menu … ………………………………
Sound ……………………………………………………………
Display … ………………………………………………………
Connectivity … …………………………………………………
General … ………………………………………………………
122
123
123
124
125
Settings menu
Learn to configure your camera's settings.
Accessing the settings menu
4 Select an item.
1 On the Home screen, scroll to <Basic>.
2 Select .
3 Select a menu.
Sound
Volume
Beep Sound
Shutter Sound
Settings
Start Sound
Sound
AF Sound
Display
Connectivity
General
Medium
On
Sound 1
Off
On
Back
Select
5 Select an option.
Volume
Off
Icon
Low
Description
Medium
Sound: Set various camera sounds and the volume. (p. 123)
High
Display: Customize the display settings. (p. 123)
Connectivity: Set the connection options. (p. 124)
General: Change the settings for the camera system such as
memory format and default file name. (p. 125)
Back
6 Press [
Settings 122
Select
] to return to the previous screen.
Settings menu
Sound
Display
* Default
Item
Description
Volume
Set the volume of all sounds. (Off, Low, Medium*, High)
Set the sound the camera emits when you press the buttons or
switch modes on or off. (Off, On*)
Set the sound the camera emits when you press the shutter
button. (Off, Sound 1*, Sound 2, Sound 3)
Set the sound the camera emits when you turn on your camera.
(Off*, Star Flight, Laser Show, Cloud)
Set the sound the camera emits when you half-press the shutter
button on or off. (Off, On*)
Beep Sound
Shutter
Sound
Start Sound
AF Sound
* Default
Item
Description
Start Image
Set a start image to display when the camera turns on.
• Off*: Display no start image.
• Logo: Display a default image stored in the internal memory.
• User Image: Select User Image from the photos you captured
in the memory.
• The camera will save only one User Image in the internal
memory at a time.
• If you select a new photo as a User Image or reset your
camera, the camera will delete the current image.
Wallpapers
Guide Line
Date/Time
Display
Help Guide
Display
Settings 123
Set wallpaper for the Home screen with the desired image.
(Wallpaper Gallery, Album)
Select a guide to help you compose a scene. (Off*, 3 X 3, 2 X 2,
Cross, Diagonal)
Set whether or not to display the date and time on the camera's
display. (Off*, On)
Display a brief description of an option or menu. (Off, On*)
Settings menu
* Default
Item
Display
Brightness
Quick View
Description
Connectivity
* Default
Adjust the brightness of the screen. (Auto*, Dark, Normal,
Bright)
Item
Normal is fixed in Playback mode even if you have selected
Auto.
Video Out
Set whether or not to review a captured image before returning
to the Shooting mode. (Off, On*)
This feature does not work in some modes.
Power Save
i-Launcher
If you perform no operations for 30 seconds, the camera
automatically switches to Power save mode. (Off*, On)
In Power save mode, press any button other than [
using the camera.
] to resume
Settings 124
Description
Set the video signal output for your region.
• NTSC: USA, Canada, Japan, Korea, Taiwan, Mexico, etc
• PAL (supports only BDGHI): Australia, Austria, Belgium, China,
Denmark, England, Finland, France, Germany, Italy, Kuwait,
Malaysia, Netherlands, New Zealand, Norway, Singapore, Spain,
Sweden, Switzerland, Thailand, etc
Set i-Launcher to launch automatically when you connect your
camera to your computer. (Off, On*)
Settings menu
General
* Default
* Default
Item
Description
Network
Information
View the Mac address and network certification number of
your camera.
Set a language for the display text.
Set the time zone for your location. When you travel to
another country, select Visit, and then select the appropriate
time zone. (Home*, Visit)
Set the date and time.
Set a date format. (YYYY/MM/DD, MM/DD/YYYY,
DD/MM/YYYY)
Language
Time Zone
Date/Time Set
Date Type
Item
Specify how to name files.
• Reset: Set the file number to start from 0001 when you
insert a new memory card, format a memory card, or
delete all files.
• Series*: Set the file number to resume from the previous
file number when you insert a new memory card, format a
memory card, or delete all files.
File No.
The default date type may differ depending on the
language selected.
Set the time format. (12 Hr, 24 Hr)
Time Type
Description
The default time type may differ depending on the
language selected.
Settings 125
• The default name of the first folder is 100PHOTO and the
default name of the first file is SAM_0001.
• The file number increases by one, from SAM_0001 to
SAM_9999, each time you capture a photo or record a
video.
• The folder number increases by one, from 100PHOTO to
999PHOTO, each time a folder is full.
• The maximum number of files that can be stored in one
folder is 9,999.
• The camera defines file names according to the Design
rule for Camera File system (DCF) standard. If you
intentionally change file names, the camera may not play
back the files.
Settings menu
* Default
Item
Imprint
Item
Set whether or not to display the date and time on captured
photos. (Off*, Date, Date & Time)
AF Lamp
• The date and time will be displayed on the bottom right
corner of the photo.
• Some printer models may not print the date and time
properly.
• The photo will not display the date and time if:
-- you select Text in Scene mode
-- you select Live Panorama, Motion Photo mode
Set the camera to automatically turn off when you perform
no operations for a specified period.
(Off, 1 min, 3 min*, 5 min, 10 min)
Auto Power Off
DIRECT LINK
(Wi-Fi Button)
* Default
Description
• Your settings will not change when you replace the
battery.
• The camera will not automatically turn off when the
camera is connected to a computer or WLAN, and when
you are playing a slide show or videos.
Format
Description
Set a light to automatically turn on in dark places to help you
focus. (Off, On*)
Format the memory. Formatting will delete all files, including
protected files. (Yes, No)
Errors can occur if you use a memory card formatted by
another brand of camera, a memory card reader, or a
computer. Please format memory cards in the camera
before using them to capture photos.
Reset
Reset menus and shooting options. Date and time, language,
and video output settings will not be reset. (Yes, No)
Open Source
Licenses
Show the Open source licenses information.
Start a preset Wi-Fi function by pressing [ ].
(AutoShare*, MobileLink, Remote Viewfinder,
Auto Backup, Email, SNS & Cloud, AllShare Play)
Settings 126
Appendixes
Get information about error messages, specifications, and maintenance.
Error messages ……………………………………………………… 128
Camera maintenance ……………………………………………… 130
Cleaning your camera … ………………………………………
Using or storing the camera … …………………………………
About memory cards ……………………………………………
About the battery … ……………………………………………
130
131
132
135
Before contacting a service center … …………………………… 139
Camera specifications ……………………………………………… 142
Glossary … ………………………………………………………… 146
Index ………………………………………………………………… 151
Error messages
When the following error messages appear, try these remedies.
Error message
Card Error
Card not supported.
Connection failed.
DCF Full Error
Suggested remedies
• Turn off your camera, and then turn it on again.
• Remove your memory card, and then insert it again.
• Format your memory card.
The inserted memory card is not supported by your
camera. Insert a microSD, microSDHC, or microSDXC
memory card.
• The camera cannot connect to the network using the
selected access point. Select another AP and try again.
• The camera has failed to connect to the other devices.
Try connecting again.
File names do not match the DCF standard. Transfer the
files from the memory card to your computer and format
the card. Then, open the Settings menu and select File
No. → Reset. (p. 125)
Error message
Suggested remedies
Device disconnected.
Network connection disconnected while transferring
photos. Reselect a device that supports AllShare Play.
File Error
Delete the damaged file or contact a service center.
File system not
supported.
Initialization failed.
Password Incorrect
Low Battery
Appendixes 128
Your camera does not support the FAT file structure of
the inserted memory card. Format the memory card on
the camera.
The camera has failed to locate a device that supports
AllShare Play. Turn on devices on the network that
support AllShare Play.
The password for transferring files to another camera is
wrong. Enter the correct password.
Insert a charged battery or recharge the battery.
Error messages
Error message
Suggested remedies
Memory Full
Delete unnecessary files or insert a new memory card.
Capture photos or insert a memory card that contains
some photos.
Network connection disconnected while transferring
photos. Try restarting the AllShare Play feature.
• The camera has failed to send a photo to the other
camera. Try sending again.
• The camera has failed to send an email or transfer a
photo to a device that supports AllShare Play. Check
the network connection and try again.
No Image File
Photo transfer failed.
Transfer failed.
Appendixes 129
Camera maintenance
Cleaning your camera
Camera body
Wipe gently with a soft, dry cloth.
Camera lens and display
Use a blower brush to remove dust and wipe the lens gently with a soft cloth. If any
dust remains, apply lens cleaning liquid to a piece of lens cleaning paper and wipe
gently.
• Never use benzene, thinners, or alcohol to clean the device. These solutions can
damage the camera or cause it to malfunction.
• Do not press on the lens cover or use a blower brush on the lens cover.
Appendixes 130
Camera maintenance
Using or storing the camera
Storing for extended period of time
Inappropriate places to use or store the camera
• Avoid exposing the camera to very cold or very hot temperatures.
• Avoid using your camera in areas with extremely high humidity, or where the
humidity changes drastically.
• Avoid exposing the camera to direct sunlight and storing it in hot, poorlyventilated areas, such as in a car during summer time.
• Protect your camera and the display from impact, rough handling, and excessive
vibration to avoid serious damage.
• Avoid using or storing your camera in dusty, dirty, humid, or poorly-ventilated
areas to prevent damage to moving parts and internal components.
• Do not use your camera near fuels, combustibles, or flammable chemicals. Do
not store or carry flammable liquids, gases, or explosive materials in the same
compartment as the camera or its accessories.
• Do not store the camera where there are mothballs.
Using on beaches or shores
• Protect your camera from sand and dirt when you use it on beaches or in similar
areas.
• Your camera is not waterproof. Do not handle the battery, adapter, or memory
card with wet hands. Operating the camera with wet hands may cause damage to
your camera.
• When you store the camera for an extended period, place it in a sealed container
with an absorbent material, such as silica gel.
• Over time, unused batteries will discharge and must be recharged before use.
• You must reset the date and time when you turn the camera on after the camera
and battery have been separated for a prolonged period.
Using the camera with caution in humid environments
When you transfer the camera from a cold environment to a warm one,
condensation can form on the lens or internal components of the camera. In this
situation, turn off the camera and wait for at least 1 hour. If condensation forms
on the memory card, remove the memory card from the camera and wait until all
moisture has evaporated before reinserting it.
Other cautions
• Do not swing your camera by the strap. This may cause injury to yourself or others
or damage to your camera.
• Do not paint your camera, as paint can clog moving parts and prevent proper
operation.
• Turn off the camera when not using it.
Appendixes 131
Camera maintenance
• Your camera contains delicate parts. Avoid impacts to the camera.
• Protect the display from external force by keeping it in the case when not in
use. Protect the camera from scratches by keeping it away from sand, sharp
implements, or loose change.
• Do not use the camera if the screen is cracked or broken. Broken glass or acrylic
could cause injury to your hands and face. Take the camera to a Samsung service
center to have it repaired.
• Never place cameras, batteries, chargers, or accessories near, on, or in heating
devices, such as microwave ovens, stoves, or radiators. These devices may be
deformed and can overheat and cause a fire or explosion.
• Do not expose the lens to direct sunlight, as this may discolor the image sensor or
cause it to malfunction.
• Protect the lens from fingerprints and scratches. Clean the lens with a soft, clean,
debris-free lens cloth.
• The camera may turn off if struck or dropped. This is to protect the memory card.
Turn on the camera to use it again.
• While you use the camera, it may heat up. This is normal and should not affect
your camera’s lifespan or performance.
• When you use the camera in low temperatures, it may take some time to turn on,
the color of the display may be changed temporarily, or after-images may appear.
These conditions are not malfunctions and they will correct themselves when the
camera is returned to milder temperatures.
• Paint or metal on the outside of the camera may cause allergies, itchy skin,
eczema, or swelling for people with sensitive skin. If you experience any of these
symptoms, stop using the camera immediately and consult a doctor.
• Do not insert foreign objects into any of your camera’s compartments, slots, or
access points. Damage due to improper use may not be covered by your warranty.
• Do not allow unqualified personnel to service the camera or attempt to service
the camera yourself. Any damage that results from unqualified service is not
covered by your warranty.
About memory cards
Supported memory cards
Your camera supports microSD (Secure Digital), microSDHC (Secure Digital High
Capacity), or microSDXC (Secure Digital eXtended Capacity) memory cards.
Memory card adapter
Memory card
To read data with a PC or memory card reader, insert the memory card into a
memory card adapter.
Appendixes 132
Camera maintenance
Video
Memory card capacity
The memory capacity may differ depending on the scenes you shoot or shooting
conditions. These capacities are based on a 2 GB microSD card:
Size
1280 X 720
Photo
Size
Super Fine
Fine
Normal
218
430
637
244
481
711
287
564
832
340
666
979
634
1222
1768
1000
1887
2678
1322
2448
3419
2495
4336
5750
640 X 480
320 X 240
For Sharing
30fps
Approx. 26' 20"
Approx. 46' 55"
Approx. 261' 11"
Approx. 261' 11"
• The figures above are measured without using the zoom function.
• Available recording time may vary if you use the zoom.
• Several videos were recorded in succession to determine the total recording time.
Appendixes 133
Camera maintenance
Cautions when using memory cards
• Avoid exposing memory cards to very cold or very hot temperatures (below
0 °C/32 °F or above 40 °C/104 °F). Extreme temperatures can cause memory cards
to malfunction.
• Insert a memory card in the correct direction. Inserting a memory card in the
wrong direction may damage your camera and memory card.
• Do not use memory cards that have been formatted by other cameras or by a
computer. Reformat the memory card with your camera.
• Turn off the camera before you insert or remove the memory card.
• Do not remove the memory card or turn off your camera while the lamp is
blinking, as this may damage your data.
• When the lifespan of a memory card has expired, you cannot store any more
photos on the card. Use a new memory card.
• Do not bend, drop, or subject memory cards to heavy impact or pressure.
• Avoid using or storing memory cards near strong magnetic fields.
• Avoid using or keeping memory cards in areas with high temperatures, high
humidity, or corrosive substances.
• Prevent memory cards from making contact with liquids, dirt, or foreign
substances. If dirty, wipe the memory card clean with a soft cloth before you
insert the memory card into your camera.
• Do not allow liquids, dirt, or foreign substances to come in contact with memory
cards or the memory card slot. Doing so may cause memory cards or the camera
to malfunction.
• When you carry a memory card, use a case to protect the card from electrostatic
discharges.
• Transfer important data to other media, such as a hard disk, CD, or DVD.
• When you use the camera for an extended period, the memory card may become
warm. This is normal and does not indicate a malfunction.
Appendixes 134
The manufacturer is not responsible for any loss of data.
Camera maintenance
About the battery
Battery life
Use only Samsung-approved batteries.
Average shooting time/
Number of photos
Battery specifications
Specification
Description
Model
BP70A
Lithium-ion battery
700 mAh
3.7 V
Type
Cell capacity
Voltage
Charging time* (when the camera is
switched off)
Test conditions
(when the battery is fully charged)
Photos
Approximately
120 min/
Approximately
240 photos
The battery life was measured under the
following conditions: in Program mode, in
resolution, Fine quality, OIS on.
darkness,
1. Set the flash option to Fill in, take a single shot,
and zoom in or out.
2. Set the flash option to Off, take a single shot,
and zoom in or out.
3. Perform steps 1 and 2, waiting 30 seconds
between each step. Repeat the process for
5 minutes, and then turn off the camera for
1 minute.
4. Repeat steps 1 to 3.
Videos
Approximately
100 min
Record videos at
Approximately 150 min
* Charging the battery by connecting it to a computer may take longer.
resolution and 30 FPS.
• The figures above are measured by Samsung’s standards. Your results may differ, depending
on your actual usage.
• Several videos were recorded in succession to determine the total recording time.
• When using network functions, the battery will be depleted more quickly.
Appendixes 135
Camera maintenance
Low battery message
Cautions about using the battery
Protect batteries, chargers, and memory cards from damage
Prevent batteries from making contact with metal objects, as this can create a
connection between the + and – terminals of your battery and lead to temporary or
permanent battery damage and may cause a fire or electric shock.
When the battery has fully discharged, the battery icon will turn red and the
"Low Battery" message will appear.
Notes about using the battery
• Avoid exposing batteries to very cold or very hot temperatures (below 0 °C/32 °F
or above 40 °C/104 °F). Extreme temperatures can reduce the charging capacity of
your batteries.
• When you use the camera for an extended period, the area around the battery
chamber may become warm. This does not affect the normal use of the camera.
• Do not pull the power supply cord to disconnect the plug from the power outlet,
as this may cause a fire or electric shock.
• In temperatures below 0 °C/32 °F, battery capacity and battery life may decrease.
• Battery capacity may decrease in low temperatures, but will return to normal in
milder temperatures.
• Remove the batteries from your camera when storing it for an extended period.
Installed batteries may leak or corrode over time and cause serious damage
to your camera. Storing the camera for extended periods with the battery
installed causes the battery to discharge. You may not be able to recharge a fully
discharged battery.
• When you do not use the camera for an extended period (3 months or more),
check the battery and recharge it regularly. If you let the battery discharge
continually, its capacity and life may decrease, which can lead to a malfunction,
fire, or explosion.
Notes about charging the battery
• If the status lamp is off, make sure that the battery is inserted correctly.
• If the camera is on while charging, the battery may not fully charge. Turn off the
camera before charging the battery.
• Do not use your camera when you are charging the battery. This may cause a fire
or electric shock.
• Do not pull the power supply cord to disconnect the plug from the power outlet,
as this may cause a fire or electric shock.
• Let the battery charge for at least 10 minutes before turning on the camera.
• If you connect the camera to an external power source when the battery is
depleted, using high energy-consuming functions will cause the camera to turn
off. To use the camera normally, recharge the battery.
Appendixes 136
Camera maintenance
• If you reconnect the power cable when the battery is fully charged, the status
lamp turns on for approximately 30 minutes.
• Using the flash or recording videos depletes the battery quickly. Charge the
battery until the red status lamp turns off.
• If the status lamp blinks in red, reconnect the cable, or remove the battery and
insert it again.
• If you charge the battery when the cable is overheated or the temperature is too
high, the status lamp may blink in red. Charging will start when the battery cools
down.
• Overcharging batteries may shorten battery life. After charging is finished,
disconnect the cable from your camera.
• Do not bend or place heavy objects on the AC cable. Doing so may damage the
cable.
Handle and dispose of batteries and chargers with care
• Never dispose of batteries in a fire. Follow all local regulations when you dispose
of used batteries.
• Never place batteries or cameras on or in heating devices, such as microwave
ovens, stoves, or radiators. Batteries may explode when they are overheated.
Notes about charging with a computer connected
• Use only the provided USB cable.
• The battery may not charge when:
-- you use a USB hub
-- other USB devices are connected to your computer
-- you connect the cable to the port on the front side of your computer
-- the USB port of your computer does not support the power output standard
(5 V, 500 mA)
Appendixes 137
Camera maintenance
Personal injury or death can occur if the battery is handled
carelessly or improperly. For your safety, follow these instructions
for proper battery handling:
• The battery can ignite or explode if not handled properly.
If you notice any deformities, cracks, or other abnormalities in the
battery, immediately discontinue use of the battery and contact a
service center.
• Use only authentic, manufacturer-recommend battery chargers and
adapters and charge the battery only by the methods described in this
user manual.
• Do not place the battery near heating devices or expose it to
excessively warm environments, such as the inside of an enclosed car
in the summertime.
• Do not place the battery in a microwave oven.
• Avoid storing or using the battery in hot, humid places, such as spas or
shower enclosures.
• Do not rest the camera on flammable surfaces, such as bedding,
carpets, or electric blankets for a prolonged period.
• When the camera is switched on, do not leave it in any confined space
for a prolonged period.
• Do not allow battery terminals to come in contact with metallic
objects, such as necklaces, coins, keys, or watches.
• Use only authentic, manufacturer-recommended, Lithium-ion
replacement batteries.
Appendixes 138
• Do not disassemble the battery or puncture it with any sharp object.
• Avoid exposing the battery to high pressure or crushing forces.
• Avoid exposing the battery to major impacts, such as dropping it from
high places.
• Do not expose the battery to temperatures of 60 °C (140 °F) or above.
• Do not allow the battery to come in contact with moisture or liquids.
• Do not expose the battery to sources of excessive heat such as
sunshine, fire or the like.
Disposal guidelines
• Dispose of the battery with care.
• Do not dispose of the battery in a fire.
• Disposal regulations may differ by country or region.Dispose of the
battery in accordance with all local and federal regulations.
Guidelines for charging the battery
Charge the battery only by the methods described in this user manual.
The battery can ignite or explode if not charged properly.
Before contacting a service center
If you are having trouble with your camera, try these troubleshooting procedures before you contact a service center. If you have attempted the suggested remedy and are still
having problems with your device, contact your local dealer or service center.
When you leave your camera at a service center, be sure to also leave the other components that may have contributed to the malfunction, such as the memory card and battery.
Situation
Cannot turn on the camera
The power turns off suddenly
The camera is losing battery
power quickly
Suggested remedies
• Ensure that the battery is inserted.
• Ensure that the battery is inserted correctly.
(p. 23)
• Charge the battery.
• Charge the battery.
• Your camera may be in Auto Power Off mode.
(p. 126)
• The camera may turn off to prevent the
memory card from being damaged due to an
impact. Turn on your camera again.
• The battery may lose power more quickly in
low temperatures (below 0 °C/32 °F). Keep the
battery warm by putting it into your pocket.
• Using the flash or recording videos depletes the
battery quickly. Recharge if needed.
• Batteries are consumable parts that must be
replaced over time. Get a new battery if the
battery life is diminishing quickly.
Situation
Cannot capture photos
The camera freezes
The camera heats up
The flash does not work
The flash fires unexpectedly
Appendixes 139
Suggested remedies
• There is no space on the memory card. Delete
unnecessary files or insert a new card.
• Format the memory card.
• The memory card is defective. Get a new
memory card.
• Make sure that the camera is switched on.
• Charge the battery.
• Make sure that the battery is inserted correctly.
Remove the battery and insert it again.
While you use the camera, it may heat up. This
is normal and should not affect your camera’s
lifespan or performance.
• The flash option may be set to Off. (p. 61)
• You cannot use the flash in some modes.
The flash may fire due to static electricity. The
camera is not malfunctioning.
Before contacting a service center
Situation
Suggested remedies
Situation
The date and time are
incorrect
Set the date and time in the display settings.
(p. 125)
The display or buttons do not
work
Remove the battery, and then insert it again.
• Make sure that the focus option you set is
suitable for close-up shots. (p. 64)
• Make sure that the lens is clean. If not, clean the
The photo is blurry
lens. (p. 130)
• Make sure that the subject is within range of
the flash. (p. 143)
An incorrect White Balance can create unrealistic
The colors in the photo do not
color. Select the proper White Balance option to
match the actual scene
suit the light source. (p. 71)
Your photo is overexposed.
• Turn off the flash. (p. 61)
The photo is too bright
• Adjust the ISO sensitivity. (p. 63)
• Adjust the exposure value. (p. 69)
Your photo is underexposed.
• Turn on the flash. (p. 61)
The photo is too dark
• Adjust the ISO sensitivity. (p. 63)
• Adjust the exposure value. (p. 69)
If you use your camera at very low temperatures,
it may cause the camera screen to malfunction
or discolor. For better performance of your
camera screen, use your camera in moderate
temperatures.
• Turn off your camera, and then turn it on again.
• Remove your memory card, and then insert it
again.
The memory card has an error
• Format your memory card.
See “Cautions when using memory cards” for
more detail. (p. 134)
If you change the name of a file, your camera may
not play the file (the name of the file should meet
Cannot play back files
the DCF standard). If you encounter this situation,
play back the files on your computer.
The camera display responds
poorly
Appendixes 140
Suggested remedies
Before contacting a service center
Situation
The TV does not display your
photos
Your computer does not
recognize your camera
Your computer disconnects
the camera while transferring
files
Your computer cannot play
videos
Suggested remedies
Situation
• Make sure that the camera is correctly
connected to the TV with the A/V cable.
• Make sure that your memory card contains
photos.
• Make sure that the USB cable is connected
correctly.
• Make sure that your camera is switched on.
• Make sure that you are using a supported
operating system.
The file transmission may be interrupted by static
electricity. Disconnect the USB cable and connect
it again.
Videos may not play on some video player
programs. To play video files captured with your
camera, use the Multimedia Viewer program that
you can install with the i-Launcher program on
your computer.
i-Launcher is not functioning
properly
Your TV or computer
cannot display photos and
videos that are stored on a
microSDXC memory card.
Your computer does not
recognize a microSDXC
memory card.
Appendixes 141
Suggested remedies
• End i-Launcher and restart the program.
• Make sure that i-Launcher is set to On in the
settings menu. (p. 124)
• Depending on your computer's specifications
and environment, the program may not launch
automatically. In this case, click Start →
All Programs → Samsung → i-Launcher →
Samsung i-Launcher on your Windows
computer. (For Windows 8, open Start screen,
and then select All apps → Samsung
i-Launcher.) Or, click Applications →
Samsung → i-Launcher on your Mac OS
computer.
microSDXC memory cards use the exFAT file
system. Ensure that the external device is
compatible with the exFAT file system before
connecting the camera to the device.
microSDXC memory cards use the exFAT file
system. To use microSDXC memory cards on a
Windows XP computer, download and update
the exFAT file system driver from the Microsoft
website.
Camera specifications
Image sensor
Type
1/2.3" (Approximately 7.73 mm) CCD
Effective pixels
Approximately 16.2 mega-pixels
Total pixels
Lens
Approximately 16.6 mega-pixels
Normal (AF)
Range
Wide (W)
31 in. (80 cm)infinity
Macro
2-31 in. (5-80 cm)
Auto Macro
2 in. (5 cm) -infinity
Tele (T)
98 in. (250 cm)infinity
51-98 in.
(130-250 cm)
51 in. (130 cm)infinity
Focal length
Samsung Lens f = 4.3–43.0 mm
(35 mm film equivalent: 24–240 mm)
F-stop range
F3.1(W)–F6.3(T)
Zoom
• Still image mode: 1.0–10.0X
(Optical zoom X Digital zoom: 50.0X,
Optical zoom X Intelli zoom: 20.0X)
• Playback mode: 1.0–14.4X (depending on image size)
• Smart Auto: 1/8–1/2,000 sec.
• Program: 1–1/2,000 sec.
• Night: 16–1/2,000 sec.
• Fireworks: 2 sec.
Exposure
Type
TFT LCD
Control
Program AE
Feature
Focusing
3.0" (75.0 mm) 230K
Metering
Multi, Spot, Center-weighted, Face Detection
Compensation
±2EV (1/3 EV Step)
ISO equivalent
Auto, ISO 80, ISO 100, ISO 200, ISO 400, ISO 800, ISO 1600,
ISO 3200
Display
Type
TTL auto focus (Center AF, Multi AF, Tracking AF,
Face Detection AF), Video continuous auto focus
Shutter speed
Appendixes 142
Camera specifications
Flash
Shooting
Mode
Auto, Red-eye, Fill in, Slow Sync, Off, Red-eye Fix
Range
• Wide: 7.87-129.92 in. (0.2-3.3 m) (ISO Auto)
• Tele: 19.69-62.99 in. (0.5-1.6 m) (ISO Auto)
Recharging time
Approximately 4 sec.
Shake reduction
Photos
• Modes: Smart Auto (Portrait, Night Portrait, Backlight
Portrait, Night, Backlight, Landscape, White, Natural Green,
Blue Sky, Sunset, Macro, Macro text, Macro Color, Tripod,
Action, Fireworks, Candle, Spotlight, Spotlight (Macro),
Spotlight (Portrait)), Program, Scene (Landscape, Sunset,
Dawn, Backlight, Beach & Snow, Text), Live Panorama,
Beauty Shot, Night Shot, Close-up Shot, Magic Frame,
Photo Filter, Split Shot, Motion Photo
• Burst: Single, Continuous, Motion Capture, AEB
• Timer: Off, 10 Sec, 2 Sec, Double (10 Sec, 2 Sec)
Videos
• Modes: Smart Scene Detection (Landscape, Blue Sky,
Natural Green, Sunset), Movie Filter
• Format: MP4 (H.264) (Max recording time: 20 min)
• Size: 1280 X 720, 640 X 480, 320 X 240, 240 Web
• Frame Rate: 30 fps
• Sound Alive: Sound Alive On, Sound Alive Off, Mute
• Video editing (embedded): Pause during recording
• Timer: Off, 10 Sec
Optical Image Stabilization (OIS)
Effect
Photo Shooting
mode
• Photo Filter (Smart Filter): Miniature, Vignetting, Ink Painting,
Oil Painting, Cartoon, Cross Filter, Sketch, Soft Focus, Fish-eye,
Old Film, Half Tone Dot, Classic, Retro, Zooming Shot
• Image Adjust: Sharpness, Contrast, Saturation
Video Shooting
mode
Movie Filter (Smart Filter): Miniature, Vignetting, Half Tone Dot,
Sketch, Fish-eye, Classic, Retro, Palette Effect 1, Palette Effect 2,
Palette Effect 3, Palette Effect 4
White Balance
Auto WB, Daylight, Cloudy, Fluorescent_H, Fluorescent_L, Tungsten, Custom Set
Date Imprinting
Date & Time, Date, Off
Appendixes 143
Camera specifications
Playback
Photos
Videos
• Type: Single image, Thumbnails, Multi Slide Show with Music
and Effect
• Edit: Resize, Rotate, Smart Filter, Crop
• Effect: Brightness, Contrast, Saturation, ACB, Face Retouch,
Red-eye Fix, Smart Filter (Normal, Miniature, Vignetting,
Ink Painting, Oil Painting, Cartoon, Cross Filter, Sketch,
Soft Focus, Fish-eye, Old Film, Half Tone Dot, Classic, Retro,
Zooming Shot)
File format
Icon
Size
4608 X 3456
4608 X 3072
4608 X 2592
Image size
3648 X 2736
2592 X 1944
Edit: Still image capture, Time trimming
1984 X 1488
Storage
Media
• Still Image: JPEG (DCF), EXIF 2.21, GIF
• Movie Clip: MP4 (Video: MPEG-4.AVC/H.264, Audio: AAC)
• Internal memory: Approximately 9.5 MB
• External memory (Optional):
microSD card (2 GB guaranteed),
microSDHC card (up to 32 GB guaranteed),
microSDXC card (up to 64 GB guaranteed)
Internal memory capacity may not match these specifications.
Appendixes 144
1920 X 1080
1024 X 768
Camera specifications
Wireless network
Dimensions (W X H X D)
MobileLink, Remote Viewfinder, Auto Backup, Email, SNS & Cloud, AllShare Play,
AutoShare, Wi-Fi Direct, S/W Upgrade Notifier
Interface
3.86 X 2.28 X 0.65 in. (98.0 X 57.9 X 16.5 mm) (without protrusions)
Weight
4.62 oz (131 g) (without battery and memory card)
Digital output
connector
USB 2.0
Audio input/
output
Internal speaker (Mono), Microphone (Mono)
Operating Humidity
Video output
A/V: NTSC, PAL (selectable)
5–85 %
DC power input
connector
5.0 V
i-Launcher
Operating Temperature
0–40 °C (32-104 °F)
Power source
Software
Specifications may change without notice to improve performance.
Rechargeable
battery
Lithium-ion battery (BP70A, 700 mAh)
Connector type
Micro USB (5 pin)
The power source may differ depending on your region.
Appendixes 145
Glossary
ACB (Auto Contrast Balance)
This feature automatically improves the contrast of your images when the subject is
backlit or when there is a high contrast between your subject and the background.
Composition
Composition in photography means arranging objects in a photo. Usually, abiding
by the rule of thirds leads to a good composition.
AEB (Auto Exposure Bracket)
This feature automatically captures several images at different exposures to help
you capture a properly-exposed image.
DCF (Design rule for Camera File system)
A specification to define a file format and file system for digital cameras created by
the Japan Electronics and Information Technology Industries Association (JEITA).
AF (Auto Focus)
A system that automatically focuses the camera lens on the subject. Your camera
uses the contrast to focus automatically.
Depth of field
The distance between the nearest and farthest points that can be acceptably
focused in a photograph. Depth of field varies with lens aperture, focal length, and
distance from the camera to the subject. Selecting a smaller aperture, for example,
will increase the depth of field and blur the background of a composition.
Aperture
The aperture controls the amount of light that reaches the camera’s sensor.
Camera shake (Blur)
If the camera is moved while the shutter is open, the entire image may appear
blurred. This occurs more often when the shutter speed is slow. Prevent camera
shake by raising the sensitivity, using the flash, or using a faster shutter speed.
Alternately, use a tripod, the DIS or OIS function to stabilize the camera.
Digital zoom
A feature that artificially increases the amount of zoom available with a zoom lens
(Optical zoom). When using the Digital zoom, the image quality will deteriorate as
the magnification increases.
Appendixes 146
Glossary
EV (Exposure Value)
All the combinations of the camera’s shutter speed and lens aperture that result in
the same exposure.
EV Compensation
This feature allows you to quickly adjust the exposure value measured by the
camera, in limited increments, to improve the exposure of your photos. Set the EV
compensation to -1.0 EV to adjust the value one step darker and 1.0 EV to one step
brighter.
Exif (Exchangeable Image File Format)
A specification to define an image file format for digital cameras created by the
Japan Electronic Industries Development Association (JEIDA).
Exposure
The amount of light allowed to reach the camera’s sensor. Exposure is controlled by
a combination of the shutter speed, the aperture value, and ISO sensitivity.
Flash
A speed light that helps to create adequate exposure in low-light conditions.
Focal length
The distance from the middle of the lens to its focal point (in millimeters). Longer
focal lengths result in narrower angles of view and the subject is magnified. Shorter
focal lengths result in wider angles of view.
H.264/MPEG-4
A high-compression video format established by international standard
organizations ISO-IEC and ITU-T and developed by the Joint Video Team (JVT). This
codec is capable of providing good video quality at low bit rates.
Image sensor
The physical part of a digital camera that contains a photosite for each pixel in
the image. Each photosite records the brightness of the light that strikes it during
an exposure. Common sensor types are CCD (Charge-coupled Device) and CMOS
(Complementary Metal Oxide Semiconductor).
Appendixes 147
Glossary
ISO sensitivity
The sensitivity of the camera to light, based on the equivalent film speed used in
a film camera. At higher ISO sensitivity settings, the camera uses a higher shutter
speed, which can reduce blur caused by camera shake and low light. However,
images with high sensitivity are more susceptible to noise.
JPEG (Joint Photographic Experts Group)
A lossy method of compression for digital images. JPEG images are compressed to
reduce their overall file size with minimal deterioration of the image resolution.
LCD (Liquid Crystal Display)
A visual display commonly used in consumer electronics. This display needs a
separate backlight, such as CCFL or LED, to reproduce colors.
Macro
This feature allows you to capture close-up photos of very small objects. When
using the macro feature, the camera can maintain a sharp focus on small objects at
a near life-size ratio (1:1).
Metering
The metering refers to the way in which the camera measures the quantity of light
to set the exposure.
MJPEG (Motion JPEG)
A video format which is compressed as a JPEG image.
Noise
Misinterpreted pixels in a digital image that may appear as misplaced or random,
bright pixels. Noise usually occurs when photos are shot with a high sensitivity or
when a sensitivity is automatically set in a dark place.
OIS (Optical Image Stabilization)
This feature compensates in real-time for shaking and vibrating while shooting.
There is no image degradation compared to Digital Image Stabilization feature.
Optical zoom
This is a general zoom which can enlarge images with a lens and does not degrade
the quality of images.
Appendixes 148
Glossary
Quality
An expression of the rate of compression used in a digital image. Higher quality
images have a lower rate of compression, which usually results in a larger file size.
Resolution
The number of pixels present in a digital image. High resolution images contain
more pixels and typically show more detail than low resolution images.
White balance (color balance)
An adjustment of the intensities of colors (typically the primary colors red, green,
and blue), in an image. The goal of adjusting the white balance, or color balance, is
to correctly render the colors in an image.
Shutter speed
Shutter speed refers to the amount of time it takes to open and close the shutter,
and it is an important factor in the brightness of a photo, as it controls the amount
of light which passes through the aperture before it reaches the image sensor. A
fast shutter speed allows less time to let light in and the photo becomes darker and
more easily freezes subjects in motion.
Vignetting
A reduction of an image’s brightness or saturation at the periphery (outer edges)
compared to the center of the image. Vignetting can draw interest to subjects
positioned in the center of an image.
Appendixes 149
Correct disposal of batteries in this product
(Applicable in countries with separate collection systems)
Correct Disposal of This Product
Waste Electrical & Electronic Equipment)
(Applicable in countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and
its electronic accessories (e.g. charger, headset, USB cable) should not be disposed
of with other household waste at the end of their working life. To prevent possible
harm to the environment or human health from uncontrolled waste disposal, please
separate these items from other types of waste and recycle them responsibly to
promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this
product, or their local government office, for details of where and how they can take
these items for environmentally safe recycling.
This marking on the battery, manual or packaging indicates that the batteries in
this product should not be disposed of with other household waste at the end of
their working life. Where marked, the chemical symbols Hg, Cd or Pb indicate that
the battery contains mercury, cadmium or lead above the reference levels in EC
Directive 2006/66. If batteries are not properly disposed of, these substances can
cause harm to human health or the environment.
To protect natural resources and to promote material reuse, please separate
batteries from other types of waste and recycle them through your local, free
battery return system.
Business users should contact their supplier and check the terms and conditions
of the purchase contract. This product and its electronic accessories should not be
mixed with other commercial wastes for disposal.
PlanetFirst represents Samsung Electronics' commitment to
sustainable development and social responsibility through ecodriven business and management activities.
Appendixes 150
Index
A
B
AF-assist light
Battery
Location 20
Settings 126
AF Sound 123
AllShare Play 117
Auto Backup 110
Auto Contrast Balance (ACB)
Playback mode 90
Shooting mode 70
Auto Exposure Bracket (AEB) 73
AutoShare 106
A/V port 20
C
D
CAF (Continuous AF) 46
Date/Time Set 125
Camera maintenance 130
Deleting files 82
Camera specifications 142
Digital zoom 37
Beauty Shot mode 50
Capturing an image from video 87
DIRECT LINK button 22
Blink Detection 68
Charging 24
Disconnecting the camera 93
Brightness
Cleaning
Display brightness 124
Caution 136
Charging 24
Inserting 23
Playback mode 90
Shooting mode 69
Burst modes
Auto Exposure Bracket (AEB) 73
Continuous 73
Motion Capture 73
Camera body 130
Display 130
Lens 130
Close-up Shot mode 51
Connecting to your Mac
computer 94
Contrast
Playback mode 90
Shooting mode 74
Display type 34
E
Editing photos 88
Editing videos
Capturing 87
Trimming 87
Enlarging 83
Error messages 128
Exposure 69
Appendixes 151
Index
F
H
Imprint 126
Face Detection 67
Half-press shutter 40
Intelli zoom 38
Flash
Home screen 28
ISO sensitivity 63
I
L
Motion Capture 73
Icons
Language settings 125
Motion Photo mode 55
Live Panorama mode 48
Movie Filter mode 53
Auto 61
Fill in 62
Off 61
Red-eye 62
Red-eye Fix 62
Slow Sync 62
Focus area
Center AF 65
Multi AF 65
Tracking AF 65
Formatting 126
Playback mode 79
Shooting mode 27
Image Adjustment
ACB 90
Brightness
Playback mode 90
Shooting mode 69
Contrast
G
Playback mode 90
Shooting mode 74
Red-eye 91
Guide Line 123
Saturation
Playback mode 90
Shooting mode 74
Sharpness 74
Center-weighted 70
Multi 70
Spot 70
MobileLink 107
Movie mode 46
M
Macro
Auto Macro 65
Macro 65
N
Night Shot mode 51
Magic Frame mode 52
O
Memory card
Optical Image Stabilization (OIS) 39
Caution 134
Insert 23
Menu button 21
Metering
Appendixes 152
Optional accessories 19
Index
P
Remote Viewfinder 108
Sharpness 74
Start Image 123
Photo Filter mode 52
Reset 126
Shooting portraits
Status lamp 21
Playback button 21
Resolution
Playback mode 88
Shooting mode 58
Playback mode 79
Power button 20
Retouching faces
Power save mode 124
Program mode 44
Protecting files 82
Q
Quick view 124
R
Red-eye
Playback mode 91
Shooting mode 61
Playback mode 91
Shooting mode 50
Rotating 88
S
Saturation
Playback mode 90
Shooting mode 74
Scene mode 47
Service center 139
Settings 125
Blink Detection 68
Face Detection 67
Smile Shot 67
Shutter button 20
Slide show 85
Smart Auto mode 43
Smart Filter
Photo shooting mode 52
Playback mode 89
Video recording mode 53
Smart Movie mode 45
Smile Shot 67
Sound settings 35
Split Shot mode 54
Appendixes 153
T
Thumbnails 80
Timer
Shooting mode 60
Timer lamp 20
Time settings 25
Time zone settings 25, 125
Tracking AF 66
Transferring files
Auto Backup 110
Email 112
Mac 94
Windows 93
Tripod mount 20
Index
U
W
Unpacking 19
Website
Accessing 115
Uploading photos or videos 115
USB port 20
V
White Balance 71
Video
Wireless network 102
Playback mode 86
Shooting mode 46
Video out 124
Viewing files
Animated photos 85
Category 81
Panoramic photos 84
Slide show 85
Thumbnails 80
TV 92
Z
Zoom
Using the zoom 37
Zoom button 21
Zoom sound settings 75
Appendixes 154
Please refer to the warranty that came with your product or
visit our website, www.samsung.com, for after-sales service or inquiries.
Download PDF

advertising