Samsung | HG28EC690AB | Samsung HG28EC690AB Installation Guide

LED TV
Installation manual
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service, please
register your product at
www.samsung.com/register
Model
Serial No.
Figures and illustrations in this User Manual are provided for reference only and may differ from actual product
appearance. Product design and specifications may be changed without notice.
Instruction
This TV is provided with interactive functionality through a set-back box (SBB/STB) connected to the TV, and with other TVs in a
computer-controlled system for hotels and other hospitality businesses.
Interactive: When the TV is powered-up initially, it sends a command to identify the SBB/STB; if identified, theTV switches to
ONLINE mode and full control is through the SBB/STB.
If the TV is in ONLINE mode, it stops receiving IR(Samsung remote) commands and acts according to interface protocol.
Stand-Alone: If SBB/STB is not identified, the TV should be switched to STAND-ALONE mode with restricted operation.
Operational Modes
When this TV (in Hotel mode) is operated with a SBB/STB, it is in one of two states :
• ONLINE or STAND-ALONE. In the STAND-ALONE state, the TV will act as a Hotel TV, but without active communication.
This is to prevent guests from trying to cheat the system by disconnecting the SBB/STB.
Hotel TV
Hotel Mode On
SBB/STB Online if
one success within
10 attempts
Stand-alone
Mode
SBB/STB
Online-10
consecutive
fails
Power
ON
SBB/STB
StatusAttempt
every 2secs
Online Mode
Poll Rate 20/sec
To set the details for Stand-alone or interactive mode, refer to pages 22-25(Setting the hotel option data : Stand-alone
mode and Interactive mode)
• Some operations may be restricted to prevents guests from "cheating" the TV system.
• No main menu(Interactive mode) or Channel Menu, Plug & Play in Main Menu (Stand-Alone mode)
• Limited Volume and Panel key lock or unlock
Still image warning
Avoid displaying still images (like jpeg picture files) or still image element (like TV Program logo, panorama or 4:3 image format,
stock or news bar at screen bottom etc.) on the screen. Constant displaying of still picture can cause uneven wear of screen
phosphor, which will affect image quality. To reduce risk of this effect, please follow below recommendations:
• Avoid displaying the same TV channel for long periods.
• Always try do display any image on full screen, use TV set picture format menu for best possible match.
• Reduce brightness and contrast values to minimum required to achieve desired picture quality, exceeded values may speed
up the burnout process.
• Frequently use all TV features designed to reduce image retention and screen burnout. Refer to the relevant user manual
section for details.
Securing the Installation Space
Keep required distances between the product and other objects (e.g. walls) to ensure proper ventilation.
Failing to do so may result in fire or a problem with the product due to an increase in the internal temperature.
✎✎ When using a stand or wall-mount, use parts provided by Samsung Electronics only.
• Using parts provided by another manufacturer may result in a problem with the product or injuries due to the product falling.
✎✎ The appearance may differ, depending on the product.
Installation with a stand.
Installation with a wall-mount.
10 cm
10 cm
10 cm
10 cm
10 cm
10 cm
10 cm
Contents
yy Operational Modes................................................................................................................................................ 2
yy Still image warning................................................................................................................................................ 2
yy Securing the Installation Space............................................................................................................................. 2
yy Accessories.......................................................................................................................................................... 4
yy Installing the LED TV Stand................................................................................................................................... 5
yy Assembling the swivel (32 inch TVs or larger)........................................................................................................ 7
yy Viewing the Connection Panel............................................................................................................................... 9
yy TV Controller....................................................................................................................................................... 12
yy Viewing the Remote Control................................................................................................................................ 13
yy Connecting the TV with SBB............................................................................................................................... 14
yy Connecting the Bathroom Speakers.................................................................................................................... 16
yy Connecting the MediaHub HD............................................................................................................................. 18
yy Connecting the RJP (Remote Jack Pack)............................................................................................................ 19
yy Connecting to a COMMON INTERFACE slot (Your TV viewing Card Slot)............................................................ 21
yy Setting the Hotel Option Data.............................................................................................................................. 22
yy Installing the Wall Mount...................................................................................................................................... 60
yy Securing the TV to the Wall................................................................................................................................. 61
yy Anti-theft Kensington Lock.................................................................................................................................. 61
yy Specifications...................................................................................................................................................... 62
yy Dimensions......................................................................................................................................................... 63
English
3
ENGLISH
yy Instruction............................................................................................................................................................. 2
Accessories
✎✎ Please make sure the following items are included with your LED TV. If any items are missing, contact your dealer.
✎✎ The items’ colour and shapes may vary depending on the model.
•
•
•
•
Remote Control & Batteries (AAA x 2)
Quick Set up Guide
CI Card Adapter
Hotel Mount Kit
• Power Cord / Data Cable
• Owner’s Instructions
Safety Guide (Not available in all locations)
• Cable Holder
✎✎ The stand and stand screw may not be included, depending on the model.
✎✎ The Data Cable may not be included, depending on the SI Vendor.
Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its electronic
accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste
at the end of their working life. To prevent possible harm to the environment or human health from
uncontrolled waste disposal, please separate these items from other types of waste and recycle them
responsibly to promote the sustainable reuse of material resources. Household users should contact either
the retailer where they purchased this product, or their local government office, for details of where and
how they can take these items for environmentally safe recycling. Business users should contact their
supplier and check the terms and conditions of the purchase contract. This product and its electronic
accessories should not be mixed with other commercial wastes for disposal.
Correct disposal of batteries in this product
(Applicable in the European Union and other European countries with separate battery return
systems.)
This marking on the battery, manual or packaging indicates that the batteries in this product should not
be disposed of with other household waste at the end of their working life. Where marked, the chemical
symbols Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the reference
levels in EC Directive 2006/66. If batteries are not properly disposed of, these substances can cause harm
to human health or the environment. To protect natural resources and to promote material reuse, please
separate batteries from other types of waste and recycle them through your local, free battery return
system.
4
English
Installing the LED TV Stand
The 32” and larger LED TVs have swivel stands. You can set these stands so that the TVs swivel 20 degrees left and
right or 90 degrees left and right.
Stand Components
When installing the stand, use the provided components and parts.
A
1 EA
B 1 EA
C
28" ~ 32"
x7 (M4 X L12)
32"
D
28"
32" ~ 55"
28"
• Stand
40" ~ 55"
x8 (M4 X L12)
40" ~ 55"
• Guide Stand
• Screws
HG28EC690
1
x4
C
2
(M4 X L12)
1-1
B
1-2
A
2-1
2-2
2-3
1-3
✎✎ Place a soft cloth over the table to protect the TV, and then place the TV
on the cloth screen-side down.
✎✎ Insert the Stand Guide into the slot on the bottom of the TV.
✎✎ Slide and assemble it to the end line in the direction of arrow.
3
Tight the bottom of the screw first, and stow the upper side
of screw last.
When the declination happened, try reassemble it
category.
2
✎✎ Make sure to assembling stand guide attached on the TV.
x3
C
4
(M4 X L12)
3-1
3-2
✎✎ Progress the assembly of screw in the manual’s order.
English
5
HG32EC690 / HG40EC690 / HG48EC690 / HG55EC690
x4
C
1
2
(M4 X L12)
1-1
B
A
1-2
2-1
1-3
3
2-2
2-3
✎✎ Place a soft cloth over the table to protect the TV, and then place
the TV on the cloth screen-side down.
✎✎ Insert the Stand Guide into the slot on the bottom of the TV.
✎✎ Slide and assemble it to the end line in the direction of arrow.
3-1
Tight the bottom of the screw first, and stow the upper side of screw last.
C 32"
x3 (M4 X L12)
3-2
D 40" ~ 55"
x4 (M4 X L12)
✎✎ Progress the assembly of screw in
the manual’s order.
4
When the declination happened, try reassemble it
2
category.
✎✎ Make sure to assembling stand guide attached on the TV.
✎✎NOTE
yy Make sure to distinguish between the front and back of each component when assembling them.
yy Make sure that at least two persons lift and move the TV.
6
English
Assembling the swivel (32 inch TVs or larger)
]] WARNING: If you configure the TV to swivel, you must attach it securely to the floor, a desk, a dresser top, etc. as
described in the installation instructions.
The 32” and larger LED TVs have swivel stands. You can configure these stands so that the TVs swivel 20 degrees left and
right, 60 degrees left and right, or 90 degrees left and right using the BRACKET HOLDER SWIVEL.
¦¦ 20° Swivel
To configure the TV so that it swivels 20° left and right, insert the prong on the bottom of the stand through the curved hole
in the Bracket Holder Swivel marked 20°. Then, fix the Bracket Holder Swivel to the stand using the three supplied screws as
shown below.
¦¦ 60° Swivel
To configure the TV so that it swivels 60° left and right, insert the prong on the bottom of the stand through the curved hole
in the Bracket Holder Swivel marked 60°. Then, fix the Bracket Holder Swivel to the stand using the three supplied screws as
shown below.
¦¦ 90° Swivel
To configure the TV so that it swivels 90° left and right, remove the Bracket Holder Swivel, and then screw the three supplied
screws into the stand as shown below.
English
7
¦¦ Hotel Mount Kit
Bolt + Nut
Short Bolt (2EA)
Long Bolt (2EA)
Nut (2EA)
Washer (2EA)
Top
Bottom
[
8
English
Affix the stand to a flat surface such as a
dresser top, desk top, or entertainment center as
shown.
WARNING: To prevent injury, you must attach this TV securely to the floor, a table, a dresser top, etc. with
the Hotel Mount Kit as described in these instructions.
$
Viewing the Connection Panel
HG28EC690**
1
$
2
3
#
3
5
@
6
!
7
0
8
4
9
HG32EC690**
HG40EC690**
HG48EC690**
HG55EC690**
#
1
$
2
@
!
0
3
#
3
5
@
6
!
7
0
8
4
9
9
✎✎ Whenever you connect an external device to your TV, make sure that power on the unit is turned off.
✎✎ When connecting an external device, match the colour of the connection terminal to the cable.
English
9
1AV IN
–– Connect audio cables to "R-AUDIO-L" on your TV and the other ends to corresponding audio out jacks on an
A/V device.
–– Connect RCA audio cables (optional) to "R - AUDIO - L" on the rear of the TV set and the other ends to
corresponding audio out jacks on the external device.
–– When connecting to AV IN, the color of the AV IN [Y/VIDEO] jack (Green) does not match the color of the video
cable (Yellow).
2USB (5V 0.5A)
USB (HDD/1.0A) / CLONING
–– Connector for software upgrades and Media Play, etc.
–– Service connection.
3HDMI IN 1, 2(DVI), 3(ARC): Connects to the HDMI jack of a device with an HDMI output.
✎✎ No sound connection is needed for an HDMI-HDMI connection. HDMI connections carry both audio and video.
✎✎ Use the HDMI IN 2(DVI) jack for a DVI connection to an external device. Use a DVI to HDMI cable or DVI-HDMI
adapter (DVI to HDMI) for the video connection and the PC/DVI AUDIO IN jacks for audio.
4ANT IN (SATELLITE), (AIR/CABLE)
–– To view television channels correctly, the TV must receive a signal from one of the following sources:
–– An outdoor antenna / A cable television system
5HEADPHONE JACK: Headphones may be connected to the headphone jack on your TV. While the headphones are
connected, the sound from the built-in speakers is disabled.
6HP-ID: Connect the cable to HP-ID and Headphone Jack simultaneously and connect it to separated Headphone
Box. See page 17. When connecting Headphone to Headphone Box, it works same as Headphone function.
Display Modes
You can also select one of the standard resolutions listed in the Resolution column. The TV will automatically adjust to
the resolution you choose.
After connecting a computer to the TV, set the screen resolution for the TV on the computer. The optimal resolution is
1920 x 1080 @ 60 Hz. If it is set to any other than in the table below, the TV may display nothing. Set the resolution
properly, referring to the user guide of the computer or its graphic card.
The resolutions in the table are recommended.
✎✎ Optimal resolution is 1366 X 768 @ 60 Hz.
10
Mode
Resolution
Horizontal Frequency
(KHz)
Vertical Frequency
(Hz)
Pixel Clock Frequency
(MHz)
Sync Polarity
(H / V)
IBM
640 x 350
720 x 400
31.469
31.469
70.086
70.087
25.175
28.322
+/-/+
MAC
640 x 480
832 x 624
35.000
49.726
66.667
74.551
30.240
57.284
-/-/-
VESA CVT
720 x 576
1280 x 720
35.910
56.456
59.950
74.777
32.750
95.750
-/+
-/+
VESA DMT
640 x 480
640 x 480
640 x 480
800 x 600
800 x 600
800 x 600
1024 x 768
1024 x 768
1024 x 768
1280 x 720
1366 x 768
31.469
37.500
37.861
37.879
46.875
48.077
48.363
56.476
60.023
45.000
47.712
59.940
75.000
72.809
60.317
75.000
72.188
60.004
70.069
75.029
60.000
60.015
25.175
31.500
31.500
40.000
49.500
50.000
65.000
75.000
78.750
74.250
85.500
-/-/-/+/+
+/+
+/+
-/-/+/+
+/+
+/+
VESA GTF
1280 x 720
52.500
70.000
89.040
-/+
English
✎✎ Optimal resolution is 1920 X 1080 @ 60 Hz.
Mode
Resolution
Horizontal Frequency
(KHz)
Vertical Frequency
(Hz)
Pixel Clock Frequency
(MHz)
Sync Polarity
(H / V)
IBM
720 x 400
31.469
70.087
28.322
-/+
MAC
640 x 480
832 x 624
1152 x 870
35.000
49.726
68.681
66.667
74.551
75.062
30.240
57.284
100.000
-/-/-/-
VESA DMT
640 x 480
640 x 480
640 x 480
800 x 600
800 x 600
800 x 600
1024 x 768
1024 x 768
1024 x 768
1152 x 864
1280 x 1024
1280 x 1024
1280 x 720
1280 x 800
1280 x 960
1366 x 768
1440 x 900
1600 x 900RB
1680 x 1050
1920 x 1080
31.469
37.861
37.500
37.879
48.077
46.875
48.363
56.476
60.023
67.500
63.981
79.976
45.000
49.702
60.000
47.712
55.935
60.000
65.290
67.500
59.940
72.809
75.000
60.317
72.188
75.000
60.004
70.069
75.029
75.000
60.020
75.025
60.000
59.810
60.000
60.015
59.887
60.000
59.954
60.000
25.175
31.500
31.500
40.000
50.000
49.500
65.000
75.000
78.750
108.000
108.000
135.000
74.250
83.500
108.000
85.500
106.500
108.000
146.250
148.500
-/-/-/+/+
+/+
+/+
-/-/+/+
+/+
+/+
+/+
+/+
-/+
+/+
+/+
-/+
+/+
-/+
+/+
✎✎ When using an HDMI/DVI cable connection, you must use the HDMI IN 2 (DVI) jack.
✎✎ The interlace mode is not supported.
✎✎ The set might operate abnormally if a non-standard video format is selected.
✎✎ Separate and Composite modes are supported. SOG is not supported.
7RJP: This port is an RJP (Remote Jack Pack) communication port that enables connecting different devices to
additional modules to improve device use and convenience.
8PC/ DVI AUDIO IN: Connects to the audio input jacks on an Amplifier/Home Theater.
9VOL-CTRL: Used to control the volume of the Bathroom speaker. Connect the Bathroom Wall Box and the
VOLCTRL port.
0VARIABLE AUDIO OUT: Used for the audio output to the Bathroom speaker. Connect the Bathroom Wall Box and
the Variable port (RCA).
!CLOCK: Set the time after connecting the cable of the External Clock to Clock jack. You can use the External Clock
Display function.
@DATA
–– Used to support data communication between the TV and the SBB.
–– Connects using RJ-12 TV type plugs.
#PC IN: Connect to the video output jack on your computer.
$LAN: Connect to a wired LAN using CAT 7 cable.
English
11
TV Controller
TV Controller is a multi directional button that helps navigate without using the remote control.
✎✎ Some functions which require a PIN code may not be available.
✎✎ The product colour and shape may vary, depending on the model.
✎✎ Exits the menu when pressing the controller for more than 1 second.
✎✎ When selecting the function by moving the controller to the up/down/left/right directions, do not press the controller.
If the controller is used first, you cannot operate it to move the up/down/left/right directions.
Function menu
TV Controller
The image is drawn by facing
the front side of the TV.
Remote control sensor
Power on
Turn the TV on by pressing the controller in standby mode.
Adjusting the volume
Adjust the volume by moving the controller from side to side when the power is
on.
Selecting a channel
Select a channel by moving the controller up and down when the power is on.
Using the function menu
Press the controller when the power is on and the function menu appears. If you
press it again, the function menu screen disappears.
Using the Menu
Selects the MENU(m) by moving the controller in the function menu screen. The
OSD(On Screen Display) of your TV’s feature appears.
Selecting the Source
Selects the Source(s) by moving the controller in the function menu screen.
The Source list screen appears.
Selecting the SMART
HUB ( ™ )
With the Function menu visible, select SMART HUB (™) by moving the Controller
upwards. The SMART HUB main screen appears. Select an application by
moving the Controller, and then pressing the Controller.
Power Off
Selects the Power Off(P) to turn the TV off by moving the controller in the
function menu screen.
✎✎ To close the Menu, SMART HUB, or Source, press the Controller for more than 1 second.
Standby mode
Do not leave your TV in standby mode for long periods of time a small amount of electric power is still consumed even
when the power button is such as when on holiday. off. It is best to unplug the power cord.
12
English
Viewing the Remote Control
✎✎ This remote control has Braille points on the Power, Channel, and Volume buttons and can be used by visually
impaired persons.
Turns the TV on and off.
Display and select available video sources.
Have direct access to channels
Alternately selects Teletext, Double or Mix.
GUIDE
TTX/MIX
Electronic Programme Guide (EPG) display.
Cut off the sound temporarily.
Adjust the volume.
Change channels.
CH LIST
Switch to the HOME Screen.
Display channel list on the screen.
HOME
Display the main on-screen menu.
CONTENT
CLOCK
Quickly select frequently used functions.
Return to the previous menu.
Exit the menu.
A
ALARM
Use these buttons in the Contents
Home.
Press to display information on the TV
screen.
CLOCK: When you press INFO key
in standby mode, TV screen displays
the time.
Select on-screen menu items and
change menu values.
Buttons in the Channel list, Contents
Home menu, etc.
View the Contents Home.
B
C
SUBT.
D
ALARM: Enter the hour you want the TV
to turn on.
W: Turns the 3D image on or off. ( Not
available )
SUBT.: Displays digital subtitles.
' : Stop.
English
13
Installing batteries (Battery size: AAA)
X
Y
Z
✎✎ NOTE
• Use the remote control within 7m of the TV.
• Bright light may affect the performance of the remote control. Avoid using nearby special fluorescent light or neon
signs.
• The colour and shape may vary depending on the model.
• Remote control button 'HOME' & '3D' are not supported. When pressing these buttons, the TV unit does not
respond.
Connecting the TV with SBB
TV Rear Panel
ETH MODEM
Data Cable
1. Connect the DATA jack of the TV to the [ETH MODEM] jack of the STB (SBB) with the Data cable.
✎✎ Use data communication.
14
English
¦¦ List of Vendors and Compatible Data Cables Supplied with the TV
• Confirm that you are using the correct data cable for your vendor. Refer to the code label on the data cables.
English
15
Connecting the Bathroom Speakers
You can connect the Bathroom Speakers using the following method.
¦¦ Connecting through the Variable Output (available without an external amplifier)
TV Rear Panel
1
Speaker
2
VOL+
VOL+
VOLVOL-
Volume Control Box
1. Connect the VARIABLE AUDIO OUT port of the TV to the Bathroom Wall Speakers of the hotel.
Speaker +
Speaker -
N/C
2. Connect the VOL-CTRL jack of the TV to the Volume Control Box Switch port on the Bathroom Wall of the hotel.
✎✎ The maximum speaker output is 4W, 8Ω.
✎✎ The VARIABLE AUDIO OUT port supports MONO sound out only.
• Installing the Volume Control
–– If you configure the Volume Control Box as shown in the figure, you can control the volume of the bathroom
speakers.
–– The jack that connects the Volume Control Box to the TV is a 3.5mm normal Phone jack.
–– Volume Control Box switch is a Tact switch.
✎✎ Setting the Sub AMP Mode
–– 0: Turns the Sub AMP function off (PWM off).
–– 1: Determines the Sub volume according to the main volume control. the sub volume is determined according to
the Power On Volume, the Min Volume, and the Max Volume values of Hotel Mode.
–– 2: Determines the volume according to the bathroom control panel setting.
• Variable Output Port Specifications
–– Speaker Wire: Use speaker cable no more than 82 feet (25m) in length.
Volume Control Box
VOL +
1
3
2
VOL - UP
GND
VOL - DOWN
( White 1 ) ( Black /Red 2 ) ( Shield Wire 3 )
16
English
VOL -
¦¦ Audio Loop In
An additional Headphone Box can be installed on a bed or business desk for added convenience. The installation
procedures are given below.
• Detailed Drawing of the Headphone Box.
TV Rear Panel
HEADPHON BOX
Headphone Box
Shield wire
TV Headphones jack
Red Wire (Audio-R)
Whitewire (Audio-L)
Red wire + White wire
Shield Wire
TV HP-ID jack
<Headphone Box>
English
17
Connecting the MediaHub HD
Output to any external source connected to MediaHub HD on the hotel desk.
MediaHub HD Rear
HDMI
USB
TV Rear Panel
RS/232
1 RS-232 Data Cable
2 HDMI cable
1. Connect the RJP port of the TV and the RS/232 port of the MediaHub HD.
2. Connect the HDMI IN 1, 2(DVI) or 3 (ARC) port of the TV and the HDMI port of the MediaHub HD.
• MediaHub HD
–– The MediaHub HD is a hardware module that has different Audio Video inputs (A/V, Audio, PC, HDMI and USB)
and corresponding outputs. The corresponding output sources connect from MediaHub to the TV. MediaHub
communicates with the TV via RS232. Hot Plug & Play is a function that allows hotel guests to connect an
external source to the MediaHub. MediaHub communicates with the TV by sending messages regarding Active/
Inactive sources. The TV switches to the Active external source.
–– You have to connect the HDMI of the MediaHub to the HDMI IN 2(DVI) port of the TV.
–– When the TV is on, connect the TV and the RJP within 10 seconds.
• Special features
–– PIP
–– Auto Detection
18
English
Connecting the RJP (Remote Jack Pack)
Output to any external source connected to RJP on the hotel desk.
RJP Rear
USB
HDMI
5
VIDEO AUDIO AUDIO/PC
RS/232
TV Rear Panel
3 Video Cable
2 Audio Cable
4 HDMI cable
1 D-sub / PC Audio cable
1. Connect the PC IN / PC/DVI AUDIO IN port of the TV to the PC/AUDIO port of the RJP.
2. Connect the AV IN [VIDEO]/[L-AUDIO-R] port of the TV to the VIDEO port of the RJP.
3. Connect the AV IN [VIDEO] port of the TV to the VIDEO port of the RJP.
4. Connect the HDMI IN 1, 2(DVI) or 3 (ARC) port of the TV and the HDMI port of the RJP.
5. Connect the RJP port of the TV and the RS/232 port of the RJP.
✎✎ The RJP (Remote Jack Pack) compatible with this Samsung TV is TeleAdapt TA-7610, TA-7650 (HD) and TA7660 (HD Plus).
• RJP (Remote Jack Pack): RJP stands for Remote Jack Pack. The RJP is a hardware module that has different Audio
Video inputs (A/V, Audio, PC and HDMI) and corresponding outputs. The corresponding output sources are connected from RJP to TV. The RJP communicates with the TV via RS232. Hot Plug & Play is a function that allows hotel
guests to connect an external source to the RJP. The RJP communicates with the TV by sending messages regarding
Active/Inactive sources. The TV will switch to the Active external source according to the priority set by the User.
✎✎ You can select HDMI IN 1, 2(DVI) or 3(ARC) and AV IN for connecting RJP.
✎✎ When the TV is on, connect the TV and the RJP within 10 seconds.
English
19
• The RJP can be returned to the factory default settings by pressing the A/V and HDMI buttons simultaneously for 10
seconds. All LEDs blink 5 times to acknowledge that this has been finished.
• The RJP will automatically turn off any LEDs after 5 minutes to avoid unnecessary light pollution in the hotel room.
The LEDs that were turned off will turn on again if the guest touches any of the buttons and the 5 minute timer will
restart. If the guest then touches another source button, the TV will change to the selected source and the corresponding LED will be lit.
• After an RJP Reset or a TV Power OFF/ON, it takes approx. 10 seconds to establish communications between the
TV and the RJP.
• The following table shows the approximate time in seconds to switch from the TV to the input source, based on the
priority.
✎✎ Scenario 1: When no inputs are connected.
Source
To Connect
AV
PC
HDMI
2 Sec
0.7 Sec
3.9 Sec
✎✎ Scenario 2: When two or more inputs are connected and an Input source is disconnected and then reconnected.
Source
Disconnect
To Connect
Total
AV
PC
HDMI
4.5 Sec
0.7 Sec
3.9 Sec
2 Sec
0.7 Sec
3.9 Sec
6.5 Sec
1.4 Sec
7.8 Sec
✎✎ E.g. If the RJP has all its live sources AV, PC and HDMI connected, AV is viewed as the highest priority. If the RJP
is in HDMI mode, and a guest removes and reconnects the AV, the minimum time required to switch to the AV is
6.5 seconds.
• To connect audio (Ipod or Mp3), Music mode should be ON and Jack Ident detect should be OFF.
• A/V, PC and HDMI input sources are supported.
20
English
Connecting to a COMMON INTERFACE slot (Your TV viewing Card Slot)
✎✎ Scenario 1: When no inputs are connected.
Attaching the CI Card Adapter
Attach the adapter as shown side.
✎✎ To install the CI CARD Adapter, please remove the sticker attached to the TV.
To connect the CI CARD Adapter, follow these steps.
✎✎ We recommend attaching the adapter before installing the wall mount, or
inserting the “CI or CI+ CARD”.
1. Insert the CI CARD Adapter into the two holes on the product 1.
✎✎ Please find two holes on the rear of the TV, beside the COMMON
INTERFACE port.
TV Rear
2. Connect the CI CARD Adapter into the COMMON INTERFACE port on
the product 2.
3. Insert the “CI or CI+ CARD”.
We recommend that you insert the CI card before you mount the TV on a wall. It may be difficult to insert after mounting. Insert the
card after attaching the CI Card Adapter on TV. It is difficult to attach the module if you insert the card before attaching.
Using the “CI or CI+ CARD”
To watch paid channels, the “CI or CI+ CARD” must be inserted.
• If you don’t insert the “CI or CI+ CARD”, some channels will display the message “Scrambled Signal”.
• The pairing information containing a telephone number, the “CI or CI+ CARD”
ID the Host ID and other information will be displayed in about 2~3 minutes. If
an error message is displayed, please contact your service provider.
• When the configuration of channel information has finished, the message “Updating Completed” is displayed, indicating the channel list is updated.
✎✎ NOTE
• You must obtain a “CI or CI+ CARD” from a local cable service provider.
• When removing the “CI or CI+ CARD”, carefully pull it out with your hands since dropping the “CI or CI+ CARD”
may cause damage to it.
• Insert the “CI or CI+ CARD” in the direction marked on the card.
• The location of the COMMON INTERFACE slot may be different depending on the model.
• “CI or CI+ CARD” is not supported in some countries and regions; check with your authorized dealer.
• If you have any problems, please contact a service provider.
• Insert the “CI or CI+ CARD” that supports the current aerial settings. The screen will be distorted or will not be
seen.
English
21
Setting the Hotel Option Data
To Enter: Press the MUTE → 1 → 1 → 9 → ENTERE buttons in order. (From the Hospitality mode, the Standalone mode is set.)
To Exit from this menu : power off and turn on again.
✎✎ Depending on Model and Region, some menus do not exist on the TV set.
Category
Hospitality
Mode
SI Vendor
Power On
Hotel TV Function
Item
initial value
Select Hospitality mode.
Standalone • Interactive mode : TV works with an SI STB or SBB.
• Stand-alone mode : TV works alone, without an SI STB or SBB.
• Interactive mode : Samsung / OCC / MTI / Nstreams / Enseo / Cardinal / Guestek
SI Vendor
OFF
/ Seachange / MDC / Innvne
• Standalone mode : Smoovie
Set the default values that will be applied when the TV is turned on.
• User Defined : Lets you set Power On Channel and Channel Type manually. See
Power On Channel
Last Saved
Power On Channel and Channel Type below.
• Last Saved : If you select this item, when the TV is turned on, it displays the channel it was displaying when it was turned off.
Power On Channel Num
1
When the TV is turned on, it switches automatically to this channel.
Select channel band : AIR (analog air band), DTV (digital air band), CATV (analog cable
Power On Channel Type
ATV
band), CDTV (digital cable band)
• User Defined : Lets you set the Power On Volume manually. See Power On
Volume below.
Power On Volume
Last Saved
• Last Saved : When the TV is turned on, it returns to the volume that had been set when the
power had been turned off.
Power On Volume Num
10
The TV turns on with this Volume Level in Stand Alone Hospitality mode.
Min Volume
0
The minimum Volume Level the user can set in Stand Alone Hospitality mode.
Max Volume
100
The maximum Volume Level the user can set in Stand Alone Hospitality mode.
Power on Source
TV
Select the input source the TV displays when turns on.
Determines the TV's state when power returns after a power failure or after you have
unplugged the TV and then plugged it in again.
• LAST OPTION : Returns to its last Power state. If it was in Stand-by, it returns to
Power On Option
Last Option
Stand-by. If it was on, it turns on.
• Power On : When the power returns, the TV turns on.
• Standby : When the power returns, the TV enters the Standby mode.
Gives you direct, immediate access to some of the Channel menu functions on the
Channel Setup
user Channel menu such as Auto Program, Antenna selection, etc.
The Channel Editor lets you edit the channels stored in the TV's memory. Using
Channel Editor you can:
• Change the channel numbers and names, and sort the channels in your desired
channel number order.
Channel Editor
• Apply the video mute to channels you select. The video mute blanks out the video from
a channel and outputs only the sound while displaying a speaker icon on the screen.
The Channel Editor also lets you view information about each channel easily, without your
having to display each channel directly.
Hospitality Mode
This Feature enables showing/browsing all antenna type (Air/Cable or Satellite)
channels at the same time.
• On: When ON, guests can access the complete Channel Map irrespective of the selected antenna type. The Channel list will also populate Air as well Cable type channels.
• Off: When OFF, guest can access the Channel Map corresponding to the selected
antenna type [AIR/CABLE or Satellite] only. The Channel list/Editor will only show
the selected antenna type channels.
• On : Check the DTV Programme channel number. (the TV channel editor is inaccessible)
• Off: Do not check the DTV Programme channel number.
(the DTV channel editor is accessible, but additional channel Programme number
update is not supported)
When there is a mismatch between the data in the channel map and the transmitted data
, the TV autotunes the channels to restore the data/parameters in the channel map.
• ON: When Channel Rescan Message is ON, The OSD showing that the channels
are being rescanned will be displayed to Hotel Guests.
• OFF: A Hotel Admin can turn the Channel Rescan Message OFF, if the rescan
message OSD should not to be displayed to Hotel Guests.
Mixed Channel Map
ON
Dynamic SI
OFF
Channel Rescan
Message
ON
Pan Euro MHEG
OFF
• OFF: If Pan EURO MHEG is set to Off, MHEG runs according to the existing product specifications.
• ON: If Pan EURO MHEG is set to On, MHEG is ON regardless of the product
specifications or region.
Mychannel
Genre Editor
OFF
...
Enable or disable the Mychannel feature.
Edith the genre for channels. (Available when Mychannel is On)
Channel
22
Description
English
Category
Channel
Hotel TV Function
Item
initial value
Subtitle Auto On
OFF
Picture Menu Lock
OFF
Menu Display
ON
Panel Button Lock
Unlock
Home Menu Display
ON
Menu OSD
Home Menu Editor
Home Menu Auto Start
ON
Clock Type
OFF
Local Time
Manual
Music Mode AV
OFF
Music Mode PC
OFF
Music Mode Backlight
OFF
Priority AV
1
Priority PC
2
Priority HDMI
3
Clock
Music
Mode
Remote
Jack Pack
External
Source
AV Option
AV
HDMI Option
HDMI 1
USB Pop-up Screen
Default
Description
This function turns the function On/Off that automatically turns on the subtitles in a specific
country.
This function is supported for Hotel TVs that are ready to receive DVB broadcasts that
is heading to Europe.
This function is related to France’s subtitle specification. The rest of the countries’ subtitles
function according to the appropriate country specifications regardless of the Subtitle Auto On
function.
• On: When the Subtitle Auto On function is ON, it follows France’s subtitle specifications.
• Off: When the Subtitle Auto On function is OFF, it does not follow France’s subtitle
specifications.
Enable or disable the Picture Menu.
• On : Main Menu display.
• Off : Main Menu No display.
Turning the front panel (local key) operations on/off.
• Unlock : Unlocks all panel keys.
• Lock : Locks all panel keys.
• OnlyPower : Locks all panel keys except the Power panel key.
• Menu/Source : Locks the Menu and Source panel keys.
OFF : The Home Menu is not displayed.
ON : The Home Menu is displayed.
Edit Home Menu
ON : The Home Menu is Auto Start.
OFF : The Home Menu is not Auto Start.
OFF : No clock option of Factory menu shall work. Only Main menu.
SW Clock : SW clock shall work only.
Select the method to update the clock data.
• Manual: Use clock data from DVB channel or manual clock setting When the TV is
in the stand-alone mode.
• Time Channel: Use clock data from the selected Channel type and Channel num.
To get music output from an mp3/audio player through an AV Input Source. When on, you can
hear sound from the player through the TV even there is no video signal. The TV’s backlight,
however, remains on. And add a video signal,it works normally.
To get music output from an mp3/audio player through a PC Input Source. When on, you
can hear sound from the player through the TV even there is no video signal. The TV’s
backlight, however, remains on. And add a video signal,it works normally.
Backlight On/Off option in Music mode to save energy
If the jack priority is set, the corresponding source is automatically set when a jack is inserted
according to the jack priority
If the jack priority is set, the corresponding source is automatically set when a jack is inserted
according to the jack priority.
If the jack priority is set, the corresponding source is automatically set when a jack is inserted
according to the jack priority.
Select RJP AV Source (Source selection depends on Model).
Select which HDMI source of the TV is connected to the RJP jack. (HDMI1/HDMI2/HDMI3)
When USB is connected to the TV,
• Default : a Popup window appears.
• Automatic : This Enters the USB content menu automatically.
• Disable : Neither the pop-up window nor the menu appears.
External Source Banner
ON
Users can set External Source Banner to On or Off.
• ON : When TV power is On or the Mode changes, the TV will displays the external source
banner.
• OFF : When TV power is On or the Mode changes, the TV does not display the external
source banner.
Auto Source
OFF
• OFF : Auto Source is Off.
• ON : When an external source is connected to the TV, the TV will auto-ident and switch
the input source.
• PC : Auto Ident PC Input only.
Anynet+ Return Source
Power On Select the return TV source after stopping an Anynet+(HDMI-CEC) connection. (This
Src
fuction is especially useful for the Guestlink RJP.)
English
23
Category
Hotel TV Function
Item
initial value
Sub AMP Mode
2
Sub AMP Volume
6
Energy Saving
Off
Welcome Message
OFF
Bathroom
Speaker
Eco
Solution
Edit Welcome Message
Hospitality Logo
OFF
Hospitality Logo DL
...
Logo Display Time
Clone TV to USB
...
Clone USB to TV
Downloads the Hospitality logo.
Hospitality logo file requirements:
• BMP or AVI files only.
• Max file size : BMP - 960 X 540. AVI - 30MB.
• The file can only be named samsung.bmp or samsung.avi.
Set the logo display time (3/5/7 Seconds).
Clone the current TV option values to a USB memory device.
When Setting Auto Initialize is set to On, and the power is turned off and on or the Master
Power is turned off and on, the data is restored to the cloned values. If there is no cloned
value, even when the Setting Auto Initialize is set to On, it will be ignored and the operation
will be the same as that whenSetting Auto Initialize is set to Off
Setting Auto Initialize
OFF
REACH Server Update Time
REACH Update Immediate
1hour
OFF
Standby REACH Server will be operated, according to time setting
Make TV operate REACH Server after 1 minute in Stand-by mode.
REACH Server Channel
87
Set the default channel for REACH Server
• None : After Auto Scan, Operate REACH Server
• Channel value : Operate REACH Server at the channel selected
REACH Server Version
0000
Display REACH Server version of TV
REACH Server Group ID
REACH
Background TV Sound
TICKER
All
...
OFF
OFF
Provided REACH Server ID for operating SIRCH on a specific set.
Set whether to use REACH function.
Background TV Sound On and Off
Ticker On and Off
AppLite
…
• On : The Applite content is displayed.
• Off : The Applite content is not displayed.
Room Number Setting
…
• Setting Room Number.
Network Setup
SmartHub Model Setting
SmartHub Setting
24
Turns the Hospitality logo feature On or Off, if On, when the TV isturned on, the Logo is
displayed, before the signal from the initial source, for the amount of time set in "Logo
Display Time"
Clone the saved TV option values in a USB memory device to the TV.
Cloning
Network
Determines the Sub AMP operation mode.
• 0: Turns the Sub AMP function off (PWM off).
• 1: Determines the Sub volume according to the main volume control.
That is, the sub volume is determined according to the Power On Volume, the Min
Volume, and the Max
• 2: Determines the volume according to the bathroom control panel setting.
Sub AMP Volume level at power on initial condition.
Adjusts the brightness of the TV to recduce power consumption.
• Off: Turns off the energy saving function.
• Low: Sets the TV to low energy saving mode.
• Medium: Sets the TV to medium energy saving mode.
• High: Sets the TV to high energy saving mode.
displays on Welcome Message.
Edit the Welcome Message.
Logo/
Message
REACH
Solution
Description
English
Set an IP address to establish an Internet connection.
Set SmartHub Model.
Set up SmartHub.
Category
Hotel TV Function
Item
initial value
Widget Mode
ON
Solution Type
Vendor
Server
Server URL Setting
Widget
Solution
Widget Mode ON/OFF.
Select type of solution (Vender Server/ SINC Server).
Set server URL.
License Server IP Setting
Set server IP.
IPTV Mode
ON
IPTV mode On/Off.
Virtual Standby
OFF
Virtual Standby mode On/Off.
When Virtual Standby is On, TV power consumption will be 9.5W to 17.4W
(Depending on the size of the TV screen).
Instant On
OFF
Setup booting mode.
Room Num Setting
Self Diagnosis
for TV
SERVICE
Description
Self Diagnosis for HTV
SW Upgrade
Service Pattern
OFF
Sound Bar Out
OFF
TV Reset
Set Room Number.
Enter Self Diagnosis Menu.
• Picture Test: Use to check for picture problems. If the problem appears in the test
picture, select Yes and follow the directions on the screen.
• Sound Test: Use the built-in melody sound to check for sound problems. If the
problem occurs during the test, select Yes and follow the directions on the screen.
HD Function Check Menu On Executing Item Below OSD is displayed ProIdiom DTV
Channel Key Loss : Ok/Failure (Hotel US) STB SI Vendor
Setting : SI Name Ok/Failure
Bathroom AMP : Ok/Failure (Hotel EU)
RTC : Ok/Failure (Hotel EU)
PC Audio Test : Ok/Failure
PC Self Test : Ok/Failure
SW USB Update function
Same function with SVC Service Pattern
ON: TV speaker sound will be mute. Sound will come out through HDMI.
You must connect the Sound Bar to hear the sound.
OFF: Sound will come out through TV speakers normally.
Returns all settings on the TV to their factory defaults.
English
25
¦¦ Welcome Message
The welcome message is used to display custom messages on the TV every time TV is turned on by a Guest in Hotel room.
–– Welcome message settings are found in the Hotel Option Menu.
–– Welcome message should be ON in order to display the message on power-on.
Hospitality Mode
Standalone
Widget Solution
OFF
SI Vendor
Service
Power On
Channel
Menu OSD
Clock
Welcome Message
Music Mode
External Source
ON
Edit Welcome Message
r
Remote Jack Pack
Hospitality Logo
Bathroom Speaker
OFF
Hospitality Logo DL
...
Logo Display Time
...
Eco Solution
Logo/Message
Cloning
REACH Solution
Network
–– A welcome message can be up to 25 characters and it can be edited by changing the text in the Hotel Service
menu.
–– The following is the list of characters supported by Welcome message:
✎✎ Capital letters, from A-Z
–– Welcome message can be edited by using the navigation, colour & enter key on the Remote in the “Edit
Welcome Message” OSD.
Edit Welcome Message
W
E
L
C
O
M
E
_
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
Move
Enter
A
Move to left
B
Move to Right
C
Leave Black
D
Done
Return
–– The Welcome message and hotel logo cannot both be active at the same time.
26
English
¦¦ Hotel Logo
The Hospitality Logo function displays the Hotel's picture image when the TV is initially powered on.
–– Hospitality Logo settings are the Hospitality mode menus.
–– The Logo Download and Logo Display Menu items are enabled when you turn the Hospitality Logo option on.
–– If there is a logo image stored in memory and the Hospitality Logo option is on, the Hospitality logo is displayed
when the TV is turned on.
–– The Hospitality logo is not displayed when the Hospitality found Logo option is off, even if the logo image has
been loaded into the TV.
Hospitality Mode
SI Vendor
Standalone
OFF
Widget Solution
Service
Power On
Channel
Menu OSD
Clock
Welcome Message
Music Mode
Edit Welcome Message
Remote Jack Pack
External Source
Bathroom Speaker
r
Hospitality Logo
OFF
BMP
Hospitality Logo DL
Logo Display Time
5 Second
Eco Solution
Logo/Message
Cloning
REACH Solution
Network
• Hospitality Logo
–– This option lets you choose whether the Hospitality Logo image is displayed or not.
–– Initial value is OFF.
–– Can be set to OFF or ON.
–– When set to ON, the Logo Download and Logo Time Display menu items become accessible.
yy Hospitality Logo DL
––
––
––
––
––
––
This option lets you download the logo image to the TV’s memory from a USB device.
A wait message appears while the image is being copied to the TV.
A "completed" message appears when the copy operation finishes successfully.
The word "failed" appears if the copy operation was unsuccessful.
No USB appears if no USB device is connected.
No File appears if there is no file to copy on the USB device or or the file is in the wrong format must be a BMP
file. If No File appears and there is a logo file on the USB device, check the file format.
• Logo File Format
–– The TV supports only BMP and AVI format.
–– The file name must be samsung.bmp or samsung.avi.
–– The maximum resolution of the BMP format is 960 x 540.
–– The maximum file size for AVI format is 30MB.
–– The TV does not change the size or scale of the image.
English
27
¦¦ USB Cloning
USB Cloning is used to download user-configured settings (Picture, Sound, Input, Channel, Setup, and Hotel Setup)
from one TV set and upload them to other TV sets.
All the user-defined settings from the TV (Master Set) can be copied to the USB device.
• Cloning from TV to USB: This copies stored data from the TV set to the USB
device.
1.Insert a USB drive into the USB port on the rear of the TV.
2.Enter the Interactive menu by pressing buttons in order.
• MUTE → 1 → 1 → 9 → ENTER
3.Press the ▲ or ▼ button to select “Clone TV to USB”, then press the ENTER button.
Logo/Message
4.When the message “Clone TV to USB” is displayed, press the ENTER button.
Cloning
5.You can verify USB cloning behavior.
• In Progress: during copying data to USB.
• Completed: copy was finished successfully.
• Failed: copy was not finished successfully.
• No USB: USB is not connected.
d
Clone TV to USB
Clone USB to TV
Setting Auto Initialize
• Cloning from USB to TV: This to downloads the stored data in the USB device to TV set.
Logo/Message
1.Insert a USB drive into the USB port on the rear of the TV.
2.Enter the Interactive menu by pressing buttons in order: MUTE → 1 → 1 → 9 →
ENTER
3.Press the ▲ or ▼ button to select “Clone USB to TV”, then press the ENTER button.
4.When the message “Clone USB to TV” is displayed, then press the ENTER button.
OFF
Cloning
d
Clone TV to USB
Clone USB to TV
Setting Auto Initialize
OFF
5.You can Make sure USB cloning behavior.
• In Progress: copying data to TV.
• Completed: copy finished successfully.
• Failed: copy did not finish successfully.
• No USB: USB is not connected.
• No File: there is no file to copy on the USB.
✎✎ Activate copying from USB to TV by pressing ENTER key for 5 seconds.
✎✎ The Hotel TV product family does not support the CLONE function between models that supports the satellite /
T2 operation and models that do not.
For fast, instant cloning during installation,
insert a USB drive with master settings from the first TV and press the Enter key for 5 seconds.
Pre-condition for cloning (check point)
–– Cloning should be done between same model (same version).
–– Before cloning, all displays should be updated at the latest version (same version).
28
English
¦¦ Setting Auto Initialize
When you clone settings from one TV to another, you clone both the guest side menu and hotel side menu settings:
Picture, Sound, Input, Channel, Setup, and Hotel Setup). This lets you set nearly all of the menu values on your
hospitality TVs to the same, standard settings. If you allow guests access to the guest side menus, for example the
Picture menu, they can change the settings in those menus so they are no longer standard. If you set the Setting Auto
Initialize function to on, the TV automatically restores (initializes) any guest-side menu values to the cloned, standard
values when the TV is turned off and then turned on again. Note that Setting Auto Initialize works on cloned guest side
menu values only. Settings which have not been cloned are ignored.
The table below lists the settings that are restored to their cloned values when you set the Setting Auto Initialize function to on.
Menu
Menu Item
Menu
Picture Mode
Picture
Backlight
Contrast
Brightness
Sharpness
Colour
Tint (G/R)
Apply Picture Mode
Picture Size
Picture Size
Zoom/Position
4:3 Screen Size
Auto Adjustment
PC Screen Adjustment
Coarse
Fine
Position
Image Reset
PIP
Advanced Settings
Dynamic Contrast
Black Tone
Flesh Tone
RGB Only Mode
Colour Space
White Balance
10p White Balance
Gamma
Expert Pattern
Motion Lighting
Picture Options
Colour Tone
Digital Clean View
MPEG Noise Filter
HDMI Black Level
Film Mode
Auto Motion Plus
Picture Off
Picture Mode Memory
Reset Picture
Menu Item
Sound
Sound Mode
Sound Effect
Virtual Surround
Dialog Clarity
Equaliser
Speaker Settings
Additional Settings
DTV Audio Level
Audio Format
Audio Delay
Dolby Digital Comp
Auto Volume
Reset Sound
System
Accessibility
Audio Description
Subtitle
Menu Transparency
High Contrast
Focus Zoom
Menu Language
Smart Touch Control Settings
Touch Sensitivity
Onscreen Remote Size
Voice Control
Language
Use TV Voice
Recognise Voice Gender
Notifications
Device Manager
Keyboard Settings
Mouse Settings
Time
Clock
Sleep Timer
Wake-up Timer
Eco Solution
Energy Saving
Eco Sensor
No Signal Power Off
Auto Power Off
Smart Security
Auto Protection Time
Change PIN
General
Game Mode
BD Wise
Sound Feedback
Boot Logo
Instant On
Anynet+(HDMI-CEC)
DivX® Video On Demand
English
29
¦¦ Plug & Play
Hotel Plug & Play automatically performs Hotel mode selection, Country Setup, Clock Setup and Picture mode Setup.
–– Hotel Plug & Play is available only one time when power is first turned ON.
–– This is available after first setting up the TV and transferring Clone TV data to a USB drive.
–– To use next TV, you only need to exit Hotel Plug & Play, connect the USB, then Clone the USB to TV.
–– Depending on model and region, some menus may not exist.
Local Set
Local Set
If you select
Change
Change Local Set if Located in North America, Latin America and Europe.
In other regions, Please press SKIP button move to the next step.
When Local Set is changed, TV will turn off automatically to apply it.
Skip
The TV is automatically
turned off and on
Next
EU
E
Change
If you change the country
of the Current Location
Warning! TV might not function if Local Set is not correctly configured.
Current Localset : EU
Countries List
Bulgaria, Croatia, Czech, Estonia, Greece, Hungary, Latvia, Lithuania,
Romania, Serbia, Slovakia, Slovenia, EU-Others
If you select Skip
E
E
TV Setup Complete!
Easy Set Up
Your TV is now ready to use.
If you select this, Easy
setup will be started.
There are Essential
Details, Channel Scan,
Clock and Terms in Easy
setup.
Interactive
(Hotel Menu)
Standalone Setup
c
Previous
Next
(Continue Setup)
Standalone Only
(End Setup)
OK
If you select
Standalone Setup
E
E
Clock
Select your Language
You can adjust your time to set DST, Time Zone and clock
mode
Select your language to start the on screen setup.
Clock Mode
c
English
Previous
Eesti
Press the udlr buttons
to move the highlight.
Press the enter button to
select.
Suomi
Next
Fraçais
Set current date and time
Auto
Date
-- / -- / ----
Time
-- : --
Time Zone
Auto
DST
Off
Deutsch
Next
-- : --
The Language Setting will be applied to Main Menu and not Plug and Play.
Select your language
E
E
Auto Tuning
Essential Details
This is basic setup to use your Smart TV.
Previous
Country
Bulgaria
Picture Mode
Standard
Auto Tuning completed.
Please Select your country
Previous
Next
Digital
- TV
- Radio
- Data/Other
0
0
0
0
Analogue
0
Next
Change settings
Scan Again
E
Auto Tuning
Auto Tuning
Auto Tuning
How do you get your broadcast signal?
To receive channels, configure the options belows then
select Scan.
Auto tuning is finding channels for you...
c
Previous
E
E
Both
Terrestrial/Cable
Satellite
Select Both to scan for both
Terrestrial or Cable channels and
Satellite channels.
Next
Aerial
Previous
Channel Type
Scan
30
English
E
Terrestrial
Digital & Analogue
Channel
Select the connected aerial that
you want to use to get channels.
Next
Previous
7
2%
Digital
- TV
- Radio
- Data/Other
0
0
0
0
Analogue
0
Next
Stop
• Plug & Play OSD
–– Initial Highlight: Interactive
–– If Standalone Only button is selected, Standalone hotel mode is set by default and “Standalone mode is set”
OSD is displayed for 3 seconds.
–– TV enters into RF mode automatically after displaying “Standalone mode is set” OSD for 3 seconds.
–– When Interactive mode is selected, the Interactive Setup Menu appears. Press the power off button to exit from
the Interactive menu.
–– When Standalone Plug & Play mode is selected, the “Select Menu Language” OSD is displayed.
• Select Menu Language OSD
–– When Standalone Plug & Play is selected from “Easy Set Up” OSD, “Select Menu Language” OSD is displayed.
–– Initial Highlight : English
–– Display time: OSD timeout and operation are the same as Samsung's consumer TV models.
–– If the ENTER button is pressed, “Select Area” OSD is displayed.
• Select Country
–– Initial Highlight: United Kingdom.
–– The Country OSD is displayed and the area can be selected.
• Clock setting OSD
–– Display time: 30 seconds.
–– The Clock Set item OSD is displayed
–– If ENTER button is pressed after setting the clock or in Auto, Picture Mode OSD is displayed.
• Auto Search Mode OSD
–– If skip option is selected, this goes to Clock setting OSD.
–– If the ENTER button is pressed, auto searching of channels is performed.
–– The OSD Display time, from the time that Auto Store is started to the time that Auto Sort is completed, is 30
seconds.
• Picture Mode OSD
–– Initial Highlight: Standard.
–– The Picture Mode OSD is displayed and the Dynamic or a Standard Picture mode can be selected.
–– After selecting the picture mode and the TV enters Standalone Setup Menu OSD, press power off to exit.
English
31
¦¦ Multi Code Remocon
Multi Code Remocon is a special transmitter which is designed to control each TV with one remote.
This is useful where there is more than one TV in a location, such as in a hospital the set ID number is displayed in the
source osd. It is possible to support up to 9 different remote key transmissions for multiple codes.
Each TV has an initial code of "0".
–– The ID code can be set and reset in Analog TV mode or PC mode. (not available in TTX channel or DTV channel.
–– ID code can be from 0 to 9.
–– Press the MUTE button and the RETURN button simultaneously for more than 7 seconds and then select the
number button to set the code.
–– Set ID OSD appears.
–– The following words appear: “Remote control code is set to 0. If you want to change Remote control code,
enter the chosen digit.” X is the digit number.
✎✎ This OSD displays until Exit is pressed.
Remote control code is set to 0. If you want
to change the Remote control code, enter the
chosen digit.
–– For example, TV and Remote will be set to ID code #1 if the user presses #1.
–– The following words appear: “Remote control code is changed to 1” At this point, the TV can be controlled only
by the remote with the same ID code as the TV.
–– TV, the following words will be displayed. “ TV ID x”(x is the TV’s ID)
–– To reset the ID code, press the MUTE button and the EXIT button simultaneously for more than 7 seconds.
When you stop pressing the buttons, the ID code for both the TV and Remote are reset to “0”. “Remote
control code is set to 0.” appears.
32
English
¦¦ CH Bank Editor (Smoovie TV Only)
Channel Bank Editor edits channels, with 3 different Bank Options.
Depending on the Bank card, there are specific channels Hotel customers can enjoy.
Setting the CH Bank Editor under Stand-alone Mode
1.Enter the Hotel Standalone menu by “MUTE+1+1+9+Enter”
2.Please select SI vendor : “Smoovie”
3.find the new menu option, “Channel Bank Editor”
4.Enter the “Channel Bank Editor”
Hospitality Mode
Standalone
SI Vendor
OFF
REACH Sever
Network
d
SI Vendor
Smoovie
d
Channel
d
Channel Bank Editor
<Depending on model and region, some menu items may not exist>
5.Edit the channel bank like below example.
a. BANK1 (Free channel): Select the channel that will be used when remote doesn’t have any card.
b. BANK2 (Family Card - Green): Select the channel that will be used when remote has a GREEN CARD.
c. BANK3 (Adult Card - Red): Select the channel that will be used when remote has a RED CARD.
Channel Bank Edit
Registered
Bank1 (4)
Bank2 (6)
BBC1
c
c
c
3
24ore.tv
c
c
c
4
C3
c
c
5
BBC World
c
c
6
C5
c
c
7
Coming Soom
c
c
8
S2
9
S2
1
1futech
2
Bank3 (36)
c
c
c
n Move
E Select/Deselect
R Return
References of using SMOOVIE Remote Controller
1.If you select SMOOVIE as the SI vendor, you should use the SMOOVIE Remote Controller.
2.With the Numeric keys of the remote controller, users can select only the Bank1 channel.
To change the channel using the Green or Red Card, please use channel up/down keys.
3.For the Channel guide or the Channel list, users can see only Bank1 channel list.
English
33
¦¦ Channel Editor
Channel Editor edits channel number a and name.
–– Use Channel Editor to sort the channels as user-desired channel numbers.
Hospitality Mode
Standalone
SI Vendor
OFF
Widget Solution
Service
Power On
Channel
Menu OSD
Clock
Music Mode
r
Remote Jack Pack
External Source
Channel Editor
Bathroom Speaker
Eco Solution
Logo/Message
Cloning
REACH Solution
Network
<Depending on model and region, some menu items may not exist>
Simple Steps for channel Editor under Stand-alone Mode
Step
Broad Outline
1
Operate ‘Channel Auto Store’ in Hotel Option Menu
2
Enter ‘Channel Editor’ in Hotel Option Menu
3
Compile a table related to the final channel lists you want to have
4
Rearrange channels with the TOOLS Button based on the table you compiled
5
Press the EXIT or RETURN Button to exit.
<please refer to the following details>
Smoovie On sequence
Smovie TV used (Air/ Cable )
Mixed Channel Map On (Air and Cable both used)
Step
If the tv starts with Hotel P&P
Only Air or Cable used
Only Air or Cable used
If P&P already done
If the tv starts with Hotel P&P
If P&P already done
1
Do the P&P, except channel
store
Enter Hotel menu
Do the P&P all (Air or Cable
auto tune)
Enter Hotel menu
2
After P&P TV shows hotel menu
Setup Mixed Channel Map On
After P&P TV will show hotel
menu
- ATV or ADTV for Air
Select channel type
3
Setup Mixed Channel Map On
TV power off & on
- ATV or ADTV for Air
4
Make TV power off & on
Enter Hotel menu
5
Enter Hotel menu
Select smoovie TV in Hotel
menu
- CATV or CDTV for cable
Select smoovie TV in Hotel
menu
Select Channel Setup
6
Select smoovie TV in Hotel
menu
Select Channel Setup
7
Select "Air + Cable" to auto tune
Setup CH Bank Editor
Select "Air + Cable" to auto tune
Setup CH Bank Editor
After power off & on, user can
use TV
9
Setup CH Bank Editor
After power off & on, user can
use TV
10
After power off & on, user can
use TV
8
34
Select Channel Setup
(can be skipped)
Select "Air" or "Cable" to auto
tune (can be skipped)
English
Select channel type
- CATV or CDTV for cable
Select smoovie TV in Hotel
menu
Select Channel Setup
Select "Air" or "Cable" to auto
tune
setup CH Bank Editor
After power off & on, user can
use TV
Smovie TV used( Satellite )
Step
1
2
3
4
5
6
7
8
9
10
Mixed Channel Map On (Satellite and Air or Cable both usedused)
Only Satellite used
If the tv starts with Hotel P&P
If P&P already done
If the tv starts with Hotel P&P
Do the P&P except channel store
Enter Hotel menu
Do P&P all: Air or Cable auto
tune)
After P&P TV will show hotel
menu
If P&P already done
Enter Hotel menu
Select channel type
Setup Mixed Channel Map On
after P&P TV shows hotel menu
- ATV or ADTV for Air
- CATV or CDTV for cable
Select channel type
- ATV or ADTV for Air
Select smoovie TV in Hotel menu
- CATV or CDTV for cable
Make TV power off & on
Enter Hotel menu
Select smoovie TV in Hotel menu
Select Channel Setup
Select Channel Setup (can be
Enter Hotel menu
Select smoovie TV in Hotel menu
Select Satellite to auto tune
skipped)
Select Satellite to auto tune (can
Setup CH Bank Editor
Select smoovie TV in Hotel menu
Select Channel Setup
be skipped)
After power off & on, user can
Select Channel Setup
Select Satellite to auto tune
Setup CH Bank Editor
use TV
After power off & on, user can
Select Satellite to auto tune
Setup CH Bank Editor
use TV
After power off & on, user can
Setup CH Bank Editor
use TV
After power off & on, user can
use TV
Setup Mixed Channel Map On
Make TV power off & on
Channel List
You can view channel information, All, TV, Radio, Data/Other, Analogue or Favourites 1-5.
✎✎ When you press the CH LIST button on the remote control, Channel List screen displays immediately.
Contents Home
Channel List
Guide
AllShare Play
Schedule Manager
Source
R Return
* The displayed image may differ depending on the model.
•
•
•
•
•
•
All: Shows all currently available channels.
TV: Shows all currently available TV channels.
Radio: Shows all currently available radio channels.
Data/Other: Shows all currently available MHP or other channels.
Analogue: Shows all currently available analogue channels.
Favourites 1-5: Shows all favourite channels.
✎✎ If you want to view added favourite channels press the CH LIST button and use the L (Ch. Mode) button to
move between Favourites 1-5.
✎✎ Using the control buttons with the Channel List.
• T (Tools): Displays the option menu.
• L (Ch. Mode / Channel): Move to the All, TV, Radio, Data/Other, Analogue or Favourites 1-5.
• When you select the Programme View in T (Tools) menu, you can move to other channels using L
(Channel) button.
• E (Watch / Information): Watches the channel you selected. / Displays details of the selected programme.
• k (Page): Move to the next or previous page.
English
35
How to use Schedule Viewing in Channel List
(digital channels only)
When you set the Schedule Viewing in Channel List, you can only set the programme in Programme View.
1. Press the CH LIST button, then select a desired digital channel.
2. Press the TOOLS button, and then select Programme View. The programme list for that channel appears.
3. Press the ▲ / ▼ buttons to select the desired programme, then press the ENTERE (Information) or INFO button.
4. Select Schedule Viewing, then press the ENTERE button when done.
✎✎ If you want to cancel Schedule Viewing, follow steps 1 through 3. Select Cancel schedule.
Using Option Menu t
Set each channel using the Channel List menu options (Programme View, Edit Favourites, Lock/Unlock, Edit
Channel Name, Edit Channel Number, Delete, Information, Sort, Edit Mode).
Option menu items may differ depending on the channel status.
1. Select a channel and press the TOOLS button.
2. Select a function and change its settings.
• Programme View: Displays the programme when a digital channel is selected.
• Edit Favourites: Set channels you watch frequently as favourites. Add or delete the selected channel in Favourites
1-5.
1.Select the Edit Favourites, then press the ENTERE button.
•
•
•
•
•
•
•
2.Press the ENTERE button to select Favourites 1-5, then press the OK button.
✎✎ One favourite channel can be added to several favourites among Favourites 1-5.
Lock/Unlock: Lock a channel so that the channel cannot be selected and viewed.
✎✎ This function is available only when the Channel Lock is set to On.
✎✎ The PIN input screen appears. Enter your 4-digit PIN. Change the PIN using the Change PIN option.
Edit Channel Name (analogue channels only): Assign your own channel name.
Edit Channel Number (digital channels only): Edit the number by pressing the number buttons.
✎✎ Some areas may not be able to support Edit Channel Name and Edit Channel Number.
Delete: You can delete a channel to display the channels you want.
Information: Displays details of the selected programme.
Sort: Changes the list ordered by channel number or channel name.
Edit Mode: Select desired channels and edit them.
Using Option Menu t
Set each channel using the menu options (Edit Favourites, Lock/Unlock, Delete, Deselect, Select All).
1. Press the TOOLS button in Channel List screen, then select the Edit Mode. A check box appears to the left of the
channel.
2. Press the ▲/▼ buttons to select the desired channel, then press the ENTERE button. The (c) mark indicates the
channel you’ve selected.
✎✎ You can select more than one channel.
✎✎ Press the ENTERE again to deselect the channel.
3. Press the TOOLS button, then select a function and change its settings.
• Edit Favourites: Set the selected channels you watch frequently as favourites.
✎✎ The Edit Favourites screen has five groups (Favourites 1, Favourites 2, etc.). You can add a favourite channel
to any one of the groups. Press the ▲/▼ buttons to select a group.
• Lock/Unlock: Lock a channel so that the channel cannot be selected and viewed.
✎✎ This function is available only when the Channel Lock is set to On.
✎✎ The PIN input screen appears. Enter your 4-digit PIN. Change the PIN using the Change PIN option.
• Delete: You can delete a channel to display the channels you want.
• Deselect: Deselect the selected channels.
• Select All: Select all the channels in the channel list.
36
English
¦¦ My Channel
Determines the country and genre for the channels provided by the hotel, and if the user selects a country and genre,
shows the corresponding channels.
• You must select the country first, or you can not set a genre.
• If you select the genre without adding any channels, the channel list displays all of the available channels.
• My Channel works in Standalone mode only.
• SI Vendor in Standalone mode: This does not work if Smoovie is selected.
• This is in the Hotel Options in Hotel Menu > Service Mode and can be turned on or off.
• The option only works when it is set to On.
• Channel Composition [Genre Mode]
Standard
Hotel
Category
Ch. Mode
Genre
All (Default)
News
Radio
Entertainment
Sport
Hotel
2
1
3
Current status : Austria/Sports
Antenna Mode Activation
Air/Cable
Satellite
O
O
O
O
O
O
O
O
O
O
O
O
Provide genre channel mode by each country that
master has managed in factory mode.
My Channel
4
Country
6
Description
5
Genre
All Country
All
Austria
News
Belgium (Dutch)
Radio
Belgium (French)
Entertainment
Czech
Sports
France
Germany
▼
Hotel
7
(Blue)Keep Previous (U/D/L/R)Move (En)Enter 8
* For the number of items to be displayed in the list, refer to the design document.
Key Guide
Button
Action
Nav. Help
BLUE
Returns to the screen. (Genre setup: Last Country & Genre)
Keep Previous
ENTER
Selects an item.
Enter
Ch. Up/Down
Move the highlight by page.
(No Guide)
UP/DOWN
Navigates the each country, genre list. (in a circular manner.)
RIGHT
Selects the highlighted item, and then move the highlight to Genre section.
RETURN
Returns to the screen. (Genre setup: Last Country & Genre)
(No Guide)
EXIT
Returns to the screen. (Genre setup: Last Country & Genre)
(No Guide)
Move
English
37
✎✎ Notes
• This section describes the layout of the Front UI that appears when the TV is turned on. (Factory Mode > Genre
Mode: Enable)
• The genre is a sub-list for each country.
• The broadcast screen that was being displayed the last memorial channel.
–– If user want to keep the previous country & genre channel map, press the ‘BLUE’, RETURN, and EXIT remotecontrol key to close the Front UI.
✎✎ Etc.
• Default Highlight : Last Memory items (Country, Genre)
• Timeout (60 sec)
Elements
No
Name
Description
1
Background Screen
Displays the last memorized channel that appears when TV is turned on.
2
Function Title
This is name of the function.
3
Current Status
Display current settings the Country/Genre.
4
Country Items
5
Genre Items
The item for the country list is displayed.
Displays the last selected country.
The item for the genre list is displayed.
Displays available genre items by each country that master managed in factory mode. (always
provide ‘All’ item)
Displays the last selected genre.
6
Highlight
If the item title is too long to be displayed within the area, Auto Text Sliding works.
7
Indicator
This is displayed when there is a previous or next page.
8
Nav. Help
The key guide is right-aligned.
38
English
Highlight Interaction [Country Items]
• This page is only to indicate possible interactions. It may not be exactly identical to actual screens.
✎✎ Notes
• Users can navigate the items in each country & genre list by pressing the up or down remote control keys.
• Circular navigation is supported.
1
My Channel
My Channel
Current status : All Country/Sports
Current status : All Country/Sports
Country
Genre
▲
DOWN x 4
Country
Genre
▲
All Country
All
All Country
All
Austria
News
Austria
News
Belgium (Dutch)
Radio
Belgium (Dutch)
Radio
Belgium (French)
Entertainment
Belgium (French)
Entertainment
Czech
Sports
Czech
Sports
France
Hotel
France
Hotel
UP x 4
Germany
Germany
▼
▼
DOWN x 4
UP x 4
My Channel
Current status : All Country/Sports
Country
Genre
▲
All Country
All
Austria
News
Belgium (Dutch)
Radio
Belgium (French)
Entertainment
Czech
Sports
France
Hotel
Germany
▼
DOWN
UP
DOWN
UP
My Channel
Current status : All Country/Sports
Country
Genre
▲
Austria
All
Belgium (Dutch)
News
Belgium (French)
Radio
Czech
Entertainment
France
Sports
Germany
Hotel
Hungary
▼
DOWN x N
UP x N
END
My Channel
My Channel
Current status : All Country/Sports
Country
Current status : All Country/Sports
Genre
▲
Country
Genre
▲
Slovakia
All
Slovakia
All
Spain
News
Spain
News
Switzerland
Radio
Switzerland
Radio
United Kingdom
Entertainment
United Kingdom
Entertainment
Eastern Europe
Sports
Eastern Europe
Sports
Other
Hotel
Other
Hotel
▼
▼
English
39
Highlight Interaction [Default Genre]
• This page is only to indicate possible interactions. It may not be exactly identical to actual screens.
My Channel
My Channel
Current status : All Country/Sports
Country
Current status : All Country/Sports
Genre
▲
All Country
All
Austria
News
Country
ENTER / RIGHT
Genre
▲
All Country
All
Austria
News
Belgium (Dutch)
Radio
Belgium (Dutch)
Radio
Belgium (French)
Entertainment
Belgium (French)
Entertainment
Czech
Sports
Czech
Sports
France
Hotel
France
Hotel
LEFT
Germany
Germany
▼
▼
Navigation Help Area
Navigation Help Area
• The current selection of the country is high-lighted.
• Default High-light: The current selection of the genre.
My Channel
My Channel
Current status : All Country/Sports
Country
Current status : All Country/Sports
Genre
Country
▲
All Country
All
Austria
News
ENTER / RIGHT
All Country
All
Austria
News
Belgium (Dutch)
Radio
Belgium (Dutch)
Radio
Belgium (French)
Entertainment
Belgium (French)
Entertainment
Czech
Sports
Czech
Sports
France
Hotel
France
Hotel
LEFT
Germany
Germany
▼
▼
Navigation Help Area
• Seems source error, it should be read as "The other
item of the county is high-lighted.". Please verify. (ex.
France)
40
Genre
▲
English
Navigation Help Area
• Default Highlight : All
Mode Change Interaction 1 (1/2)
• This page is only to indicate possible interactions. It may not be exactly identical to actual screens.
My Channel
My Channel
Current status : All Country/Sports
Country
Current status : All Country/Sports
Genre
Country
▲
Genre
▲
All Country
All
Austria
News
DOWN
All Country
All
Austria
News
Belgium (Dutch)
Radio
Belgium (Dutch)
Radio
Belgium (French)
Entertainment
Belgium (French)
Entertainment
Czech
Sports
Czech
Sports
France
Hotel
France
Hotel
LEFT
Germany
Germany
▼
▼
Navigation Help Area
Navigation Help Area
• Current Genre Mode : All Country / Sports
ENTER / RIGHT
My Channel
My Channel
Current status : All Country/Sports
Country
Current status : All Country/Sports
Genre
Country
▲
ENTER
Genre
▲
All Country
All
Austria
News
UP
All Country
All
Austria
News
Belgium (Dutch)
Radio
Belgium (Dutch)
Radio
Belgium (French)
Entertainment
Belgium (French)
Entertainment
Czech
Sports
Czech
Sports
France
Hotel
France
Hotel
DOWN
Germany
Germany
▼
▼
Navigation Help Area
Navigation Help Area
• If the country is selected, highlight moves to
genre menu automatically.
ENTER / RIGHT
6
English
41
Mode Change Interaction 1 (2/2)
• This page is only to indicate possible interactions. It may not be exactly identical to actual screens.
1
5
6
My Channel
Current status : All Country/Sports
ENTER
Country
1
Info
Genre
▲
Genre Mode change to Austria/News.
OK
All Country
All
Austria
News
Belgium (Dutch)
Radio
Belgium (French)
Entertainment
Czech
Sports
France
Hotel
Germany
▼
Navigation Help Area
• The genre mode change complete message is displayed.
• Timeout(5 sec.)
ENTER / RETURN / Timeout
Current Status : Austria / News
42
English
• Pressing the left key from the genre to country menu
highlights an existing selected country item.
Mode Change Interaction 2 (1/2)
• This page is only to indicate possible interactions. It may not be exactly identical to actual screens.
1
My Channel
My Channel
Current status : All Country/Sports
Country
Current status : All Country/Sports
Genre
▲
All Country
All
Austria
News
Country
DOWN
Genre
▲
All Country
All
Austria
News
Belgium (Dutch)
Radio
Belgium (Dutch)
Radio
Belgium (French)
Entertainment
Belgium (French)
Entertainment
Czech
Sports
Czech
Sports
France
Hotel
France
Hotel
UP x 5
Germany
Germany
▼
▼
Navigation Help Area
Navigation Help Area
• Current Genre Mode : All Country / Sports
ENTER / RIGHT
My Channel
Current status : All Country/Sports
Country
101
Info
Genre
▲
Genre Mode change to Austria/News.
OK
BLUE
/
RETURN
/
EXIT
All Country
All
Austria
News
Belgium (Dutch)
Radio
Belgium (French)
Entertainment
Czech
Sports
France
Hotel
Germany
▼
Navigation Help Area
5
ENTER
/
RETURN
/
Timeout
• If the country is selected, highlight moves to
genre menu automatically.
Current Status : Austria / News
• Current Genre Mode : All Country / Sports
English
43
Power On Scenario [Last Memory]
• This page is only to indicate possible interactions. It may not be exactly identical to actual screens.
1
Current Status : Austria / News
POWER
Power Off
• Current Genre Mode : Austria / News
POWER
My Channel
Current status : All Country/Sports
Country
Genre
▲
All Country
All
Austria
News
Belgium (Dutch)
Radio
Belgium (French)
Entertainment
Czech
Sports
France
Hotel
Germany
▼
Navigation Help Area
• Current Genre Mode : Austria / News
44
English
Genre Editor: This configures the genres of each of the hotel TV channels.
• This can be used through the Hotel Menu (Factory).
• Supported genres include News, Radio, Entertainment, Sports and Hotel.
• More than one genre can be selected for each channel at the same time.
Country Editor (Channel Editor): This is the editor that configures the country for each of the hotel TV channels.
• Supported countries (20 countries): Austria, Belgium, China, Denmark, Finland, France, Germany, Greece, Italy,
Japan, Netherlands, Norway, Portugal, Russia, Korea, Spain, Sweden, Turkey, USA
• If more than one channel is set to a country, the country is registered as a category and users can view the channels
by country.
• More than one country can be set to a channel. If the user selects a category, only the channels corresponding to the
country are displayed in the channel list.
• If any channel for which the country is set is selected from the channel list, the Edit Countries item is added to the
Tools. Otherwise, the Add to Countries item is added to the Tools.
• * If the corresponding function is executed, a country for the selected channel can be set or canceled.
• Front UI
• Provides the screen where the user can select a country or genre when the user turns the power on.
Left Frame Layout
Key Guide
Button
Action
Nav. Help
ENTER
Selects or enters the corresponding Channel Browser area.
(No Guide)
RETURN
Selects or enters the corresponding Channel Browser area.
Return
UP/DOWN
Moves the highlight up or down.
(No Guide)
RIGHT
Moves the highlight to the Channel Browser area.
(No Guide)
INFO
Shows the Category Info.
(No Guide)
TOOLS
Shows the utility function menus.
Tools
EXIT
Cancels and returns to the previous step (Factory Mode).
(No Guide)
✎✎ Notes
• This is a component of the Left Frame (Country Categories).
✎✎ Etc.
• Default Highlight: ‘The currently selected country’
English
45
Elements
No
Name
Description
• When the user enters this screen, the currently selected default item is highlighted.
• The Country Icon + Category Name are provided. (If the highlight is in the Main Frame, only the
icon is displayed.)
• Moving the highlight
–– Pressing the up or down button moves the highlight.
–– If the items cannot be displayed on one page, up and down indicators are provided.
–– Once the highlight is moved to a category, the channel list corresponding to the
corresponding category is loaded to the Main Frame.
1
Left Frame [Country Categories]
Standard
Hotel
Category
Ch. Mode
Original Tuned
Country
Antenna Mode Activation
Air/Cable
Satellite
Registered
O
O
All Country
O
O
Country 1
O
O
Country 2
O
O
.
O
O
Description
• Lists all the channels registered by the Auto
Tune operation.
• Provides the list of channels and sources
specified in the Registered Channels list.
• All Country is the sum of all channels registered to each country. (This is only provided
to end users.)
Tools [Registered/Countries Categories]
• Channel Manager > Channel Category > Tools > Info
• The items are displayed without ‘Channel’.
• If the Registered/Country item in the Left Frame is
highlighted, you can enable the corresponding window
by pressing the ‘INFO’ remote control key.
• All countries are displayed.
• navigate country items by pressing the up or down key.
Indicators are provided.
46
English
✎✎ Notes
• This is a definition of the Tools menu in the Left Frame Category.
• Only the Info item for each Register/Country is provided.
Elements
Category
Tools menu
Descriptions
Registered, Country
Information
Registered Channels. The number of channels of each country.
• The items are displayed without ‘Channel’.
Error Cases
✎✎ Notes
• This is the message for when there are no saved channels in the Registered Channels list.
Elements
No
1
Name
Message
Description
• When entering the browser, if the Registered channels item is empty,
a popup message is displayed which enables users to switch to the
Auto Store (Program) menu.
• When both the time and the channel are not configured, and a user
enters the Channel Manager, a message that allows the user to
switch to the Auto Tuning (Auto Program) operation is displayed in
the same way as above.
• This is the message when the time is not configured.
–– If the time is not configured, the message is displayed in Factory Mode before entering the Channel Manager.
English
47
✎✎ Notes
• This is the component for when there are no channels registered to the country category.
Elements
No
Description
Description
The message is displayed when the currently selected country does not contain any items.
Main Frame [Channel Browser]
48
English
Key Guide
Button
Action
Nav. Help
CH UP/DOWN
Moves the page.
Page
ENTER
Selects or enters the corresponding Channel Browser area.
Select
RETURN
Returns to the previous step (Factory Mode).
Return
UP/DOWN
Moves the highlight up or down.
(No Guide)
RIGHT
Moves the highlight to the Channel Browser area.
(No Guide)
INFO
Shows the Category Info.
(No Guide)
TOOLS
Shows the utility function menus.
Tools
EXIT
Cancels and returns to the previous step (Factory Mode).
(No Guide)
✎✎ Notes
• This is a component of the Main Frame (Channel Browser).
• The initial highlight is on the channel before entering Factory Mode or the external input.
Elements
No
Name
1
Main Frame
2
Scroll Bar
3
Navigation Help Area
• This is displayed whenever a user enters the Channel Manager. (If a user exits and
then reenters the Channel Manager, it is displayed again.)
• This disappears when the timeout (5 sec.) is reached or a user presses a key.
4
Navigation Help Area
• The currently configured country information and the RED buttons are left-aligned.
They are displayed and navigated by group graphically. The key guide is right-aligned.
Description
• Shows the channel or the source list of the currently selected category.
• Shows the position of the current page amongst the total amount of pages.
English
49
Channel Common Elements [+ Icon-method]
Channel list representation rules
Standard
Item
Construction
Digital channels
• Check Box + Status Icon + Digital Channel Number + Channel Name
• Channel number representation format: ###-### (The channel number is
represented by ‘-’.)
Analog channels
• Check Box + Analog Icon + Analog Channel Number + Channel Name
• Channel number representation format: ### (‘-’ is not used to represent analog
channel numbers.)
Digital channels
• Check Box + Status Icon + Digital Channel Number + Channel Name
• Channel number representation format: ### (For the maximum length of the
channel number, follow the regional specifications.)
Analog channels
• Check Box + Analog Icon + Analog Channel Number + Channel Name
• Channel number representation format: ### (For the maximum length of the
channel number, follow the regional specifications.)
ATSC
DVB (CHEM)
Channel list icon representation rules
Item
Example
Dynamic SI
Icon
Channels deleted by
Dynamic SI
Channels added by
Dynamic SI
Analog Channel Icon
Priority
NNNNNNNN CH. NAME
• Channels that have been deleted by the Dynamic
SI but not by the user.
1
NNNNNNNN CH. NAME
• Channels that have been added by the Dynamic
SI but not by the user.
2
• The analog channel icon is displayed.
3
• A channel that is an input source.
4
• Represents the live channels from the antennas. The Air, Cable or Satellite antenna icons are
displayed with the lowest priority.
5
NNNNNNNN CH. NAME (The
edited channel name.)
Source Channel Icon
Antenna Icon
NNNNNNNN CH. NAME
Air
NNNNNNNN CH. NAME
Cable
NNNNNNNN CH. NAME
Satellite
NNNNNNNN CH. NAME
Scrambled Channel Icon
NNNNNNNN CH. NAME
Video Mute
NNNNNNNN CH. NAME
50
English
• The scrambled channel icon. This appears for the
Satellite antenna.
• A screen-muted channel. Audio and channel
information is provided.
-
Add to Countries / Edit Countries (1/2)
• Channel Manager > Browser > Tools > Add to Countries
Key Guide
Button
Action
Nav. Help
ENTER
Selects the highlighted item.
Enter
RETURN
Cancels and returns to the previous screen (Tools).
Return
UP/DOWN
Moves the highlight over country items.
Move
LEFT/RIGHT
Moves the highlight.
Move
INFO
N/R
N/R
TOOLS
Closes the current window and displays the ‘Tools’ menu.
(No Guide)
EXIT
Cancels and returns to the previous step (Factory Mode).
(No Guide)
✎✎ Note
• This is the definition of Add to Countries.
• The highlighted channel or more than one selected channel is added to the Country category.
✎✎ Etc.
• Timeout (60 sec)
English
51
Elements
No
Name
Add to Countries
1
Window
2
Description
• If there are no channels that have been registered to the country list in
the selected channels, “Add to Countries” is displayed as the title.
• A check box is displayed depending on whether the country that was
selected when entering the screen is registered or not.
Guide
• The number of the selected channel or the channel name.
3
Selection Info
4
Complete Message
5
Selection Mark
- The channel name is displayed when one channel has been
selected: Selected channel: NNNN-NNN ABC
- The number of selected channels is displayed when more than one
channel has been selected: Selected Channels : N
• The message is displayed after the completion of the operation. (This
message is always displayed if the OK button is selected.)
• How to identify the meaning of multiple channel selection marks
• When all of the items have been registered.
• When only part of the items have been registered.
• When none of the items have been registered.
Add to Countries / Edit Countries (2/2)
• Channel Manager > Browser > Tools > Add to Countries
Key Guide
Button
Action
Nav. Help
ENTER
Selects the highlighted item.
Enter
RETURN
Cancels and returns to the previous screen (Tools).
Return
UP/DOWN
Moves the highlight over country items.
Move
LEFT/RIGHT
Moves the highlight.
Move
INFO
N/R
N/R
TOOLS
Closes the current window and displays the ‘Tools’ menu.
(No Guide)
EXIT
Cancels and returns to the previous step (Factory Mode).
(No Guide)
52
English
✎✎ Notes
• This is the definition for Edit Countries.
• The highlighted channel item or more than one selected channel item is added or deleted from the Country
category.
• Timeout (60 sec)
Elements
No
Name
1
Add to Countries
2
Guide
3
Complete Message
Description
• If there is a registered channel among the selected channels, Edit Countries is displayed as the title.
• A check box is displayed depending on whether the selected country is
registered or not.
• The message is displayed after the completion of the operation. (This
message is always displayed if the OK button is selected.)
Edit Channel Number [Swap Type]
• Channel Manager > Browser > Tools > Edit Channel Number
Key Guide
Button
Action
Nav. Help
ENTER
Applies the changes and closes the window.
Enter
RETURN
Cancels and returns to the previous screen (Tools).
Return
U/D
Changes the channel number of the selected channel.
Adjust
0~9
Enters a digit.
Number
INFO
N/R
N/R
TOOLS
Closes the current window and displays the ‘Tools’ menu.
(No Guide)
EXIT
Cancels and returns to the previous step (Factory Mode).
(No Guide)
✎✎ Notes
• This is the function that changes the channel number. (Swap Type)
• Channel numbers can be changed in all the channel lists and changes are applied to all the channels.
• If the new channel number has not been allocated to another channel, the channel number is updated to the new
channel number and the list is sorted again in ascending order of channel number.
• If the new channel number has already been allocated to another channel, follow the Hotel specifications.
✎✎ Etc. Vertical circulation is supported.
English
53
Elements
No
1
Name
Edit Channel
Number Window
Description
• Both the numeric keys and the Up/Down keys are supported.
–– Selected Channel: Shows the currently selected channel name.
–– Number: Shows the new channel number.
(The currently allocated channel name is also displayed.)
–– Name: Shows the currently allocated channel name. (If there are no
channels, it is displayed as “(Empty)”.) : If there is a channel but it
does not have a name, the name is represented as “-----”.
2
Warning
Message
• If an already allocated channel is selected
–– If the new channel number has already been allocated to another
channel, the confirmation message pops up. (Refer to the figure
below.)
–– If the user wants to change the channel number to one that has
already been allocated to another channel, the channel numbers are
swapped and saved.
Edit the Channel Number [External Input] (3/3)
• Channel Manager > Browser > Tools > Edit Channel Number
54
English
Key Guide
Button
Action
Nav. Help
RED
If a user presses the button, the channel number is initialized.
Reset
ENTER
Applies the changes and closes the window.
Enter
RETURN
Cancels or returns to the previous screen (Tools).
Return
U/D
Changes the channel number of the selected channel.
Adjust
0~9T
Enters a digit.
Number
INFO
N/R
N/R
TOOLS
Closes the current window and displays the ‘Tools’ menu.
(No Guide)
EXIT
Cancels and returns to the previous step (Factory Mode).
(No Guide)
✎✎ Notes
• This function allocates an external input source to a channel number. (The changes are applied to all the
channels.)
• If the new channel number has already been allocated to another channel, follow the Hotel specifications.
✎✎ Etc.
• Default Highlight: Channel number area.
• Vertical circulation is supported.
• Timeout (60 sec)
Elements
No
Name
Description
• The channel number area.
–– Both the numeric keys and the Up/Down keys are supported.
–– If no value is allocated, as many ‘-’ are displayed as the number of digits.
1
Channel Number Area
▲
-▼
▲
→
1
▲
→
▼
2
Source Name
• External input name
–– Items that cannot be configured are disabled.
3
Nav. Help Area
• If a user presses the red button, the channel number is initialized.
15
▼
English
55
Edit Channel Name
• Channel Manager > Browser > Tools > Edit Channel Name
Key Guide
Button
Action
GREEN
Nav. Help
Saves the changes and returns to the Channel Manager.
Done
ENTER
Saves the channel name and moves the cursor to the next field.
Enter
RETURN
Cancels and returns to the previous screen (Tools).
Return
U/D/L/R
Navigates on the keyboard.
Move
0~9
Enters a digit.
(No Guide)
INFO
N/R
N/R
TOOLS
Closes the current window and displays the ‘Tools’ menu.
(No Guide)
EXIT
Cancels and returns to the previous step (Factory Mode).
(No Guide)
✎✎ Notes
• This is the definition of the keypad that is used for the Edit Channel Name function.
✎✎ Etc.
• Timeout (60 sec)
Elements
No
Name
1
Channel Name Edit Window
2
Channel Name
3
Keyboard
56
English
Description
• The cursor and the character that are currently being entered are in the same colour as
the highlight.
• When the maximum number of characters is reached, the cursor disappears.
• For a detailed scenario, refer to the keypad design document.
Tools [Edit Mode]
Edit Mode
Content Highlight (when the number of the checked item is 0 or 1)
When there is more than one checked item.
Add to Countries
Edit Countries (when an already-registered item is checked.)
Channel Name Edit
Edit Channel Number
Video Mute
Channel Copy (Astra HD +)
Reorder (Satellite)
Select All
Deselect All (this is only displayed when 1 or more items are
selected)
Add to Countries
Edit Countries (when an already-registered item is checked.)
Video Mute
Reorder (Satellite)
Select All
Deselect All
Delete
Delete
✎✎ Notes
• The position of the popup menu: The Tools menu for an item in the left column of the Channel List → This is
displayed on the right. The Tools menu for an item in the right column of the Channel List → This is displayed on
the left.
• If a user presses the Tools button when the highlighted item is not selected, the item is automatically marked as
selected.
• For detailed specifications of each function, refer to the NEO Channel Manager.
English
57
CH Banner [when a channel number is allocated to an external input]
✎✎ Notes
• The TV channel banner specifications are applied.
• When there is an unsupported item or there is no corresponding information, the item values are not displayed.
• The channel name is represented as the ‘external input name’.
Elements
No
Name
1
External Input Name
Description
The Channel List provides access to functions related to GenreTV.
• Country Mode
• Changes the genre mode.
¦¦ Mixed Channel Map
Mixed Channel Map is a function to mix Air, Cable and Satellite channels.
[ Except for Aus, Singapore, NZ models ]
–– Mixed channel Map should be ON in order to mix Air, Cable and Satellite channels.
–– Use Channel Editor to sort the channels after turning on 'Mixed channel Map' in Hotel Option Menu.
58
English
¦¦ Sound Bar
• Samsung Sound-Bars and Hospitality TV
–– Use Samsung Sound-Bars and hospitality TVs support the ARC feature in HDMI. If you connect a compatible
Samsung Sound-Bar to a compatible Samsung hospitality TV using a single HDMI cable, guests can listen to
theTV’s sound through the Sound-Bar.
–– Models supporting the ARC function are listed below:
• Sound-Bars: HW-F350/F450/F550
• Setting the Sound-Bars to Hotel Mode.
1. Set the following Hotel menu options:
––
––
––
––
Hotel option > External Device > Sound Bar Out = On.
Hotel option > Power On > Power On Volume EN = User Defined.
Hotel option > Power On > Power On Volume > Set greater than 0.
Hotel option > Power On > Max Volume > Set greater than 0.
2.Connect an HDMI cable from the HDMI OUT jack on the back of Sound-Bar to the HDMI3 port (supporting ARC)
on the hospitality TV.
3.After the Sound-Bar is connected to the hospitality TV, when the TV turns on, the Sound-Bar automatically
detects the TV, and then automatically switches to Hotel Mode.
Sound Bar Hotel mode functional characteristics:
•
•
•
•
•
Power On/Off is synchronized with the TV
HDMI_CEC defaults to On
Functions through the “HDMI OUT” port only
Disables the “Input mode” key on the VFD to prevent unexpected audio-source changes.
Acquires adjustable Power On and Max Volume settings from the TV’s Hotel option menu. The Sound-Bar’s
Power On Volume and Max Volume values, however, are ½ of the Power On Volume and Max Volume settings in
the TV’s Hotel option menu.
Example: If the TV’s Power On Volume=20 and Max Volume=90, then the Sound Bar’s Power On Volume=10 and
Max Volume=45.
*This function may differ depending on the model.
¦¦ Security mode
Design Specifications
• This is to restrict some functions such as TTX and external source (HDMI, USB) input in specific facilities such as
a correctional facility.
• The Security menu is password-protected. Access to the Security menu is denied without the password.
• Security Setting
–– The Security Setting can be set to ON or OFF.
–– The default is OFF.
–– Security Setting: If set to On, external source (HDMI, USB) input and the TTX function will be disabled.
• Password Setting
–– This allows users to change the password.
–– Users must input the current password, a new password, and confirmation of the new password.
• Password Reset
–– This is to reset the password.
–– The default password is "00000000".
–– Password Reset is visible only in the Factory menu by using the key combination of Info and Factory.
It is not visible using the key combination of MUTE + 1 + 1 + 9 + ENTER.
• Security Setting: If set to On, the SIRCH function is not available.
• Factory Reset will not reset the Security Setting.
English
59
Installing the Wall Mount
The wall mount kit (sold separately) allows you to mount the TV on the wall. For detailed information on installing the wall
mount, see the instructions provided with the wall mount. Contact a technician for assistance when installing the wall
mount bracket. We do not advise you to do it yourself.
Samsung Electronics is not responsible for any damage to the product or injury to yourself or others if you select to
install the TV on your own.
Wall Mount Kit Specifications (VESA)
✎✎ The Wall mount kit is not supplied but sold separately.
Install your wall mount on a solid wall, perpendicular to the floor. When attaching to other building materials, please
contact your nearest dealer. If installing on a ceiling or slanted wall, it may fall and result in severe personal injury.
✎✎ NOTE
• Standard dimensions for wall mount kits are shown in the table below.
• When purchasing our wall mount kit, a detailed installation manual and all parts necessary for assembly are
provided.
• Do not use screws that do not comply with VESA standard screw specifications.
• Do not use screws longer than the standard dimensions, as they may cause damage to the inside of the TV set.
• For wall mounts that do not comply with the VESA standard screw specifications, the length of the screws may
differ depending on their specifications.
• Do not fasten the screws too tightly. This may... damage the product or cause the product to fall, leading to
personal injury. Samsung is not liable for these kinds of accidents.
• Samsung is not liable for product damage or personal injury when a non-VESA or non-specified wall mount is
used or the consumer fails to follow the product installation instructions.
• Do not exceed a 15 degrees tilt when mounting this TV.
inches
VESA Spec. (A * B)
Standard Screw
28
100 X 100
M4
32~40
200 X 200
Quantity
4
M8
48~55
400 X 400
Do not install your Wall Mount Kit while your TV is turned on. It may result in personal injury due to electric shock.
60
English
Securing the TV to the Wall
[
Caution: Pulling, pushing, or climbing onto the TV may cause the TV to fall. In particular, ensure that your children do not hang over or
destabilize the TV; doing so may cause the TV to tip over, resulting in serious injuries or death. Follow all safety precautions provided on
the included Safety Flyer. For added stability, install the anti-fall device for safety purposes, as follows.
To avoid the TV from falling
1. Put the screws into the clamps and firmly fasten them onto the wall. Confirm that the screws have been firmly
installed onto the wall.
✎✎ You may need additional material, such as an anchor, depending on the type of wall.
✎✎ Since the necessary clamps, screws, and string are not supplied, please purchase these additionally.
2. Remove the screws from the centre back of the TV, put the screws into the clamps, and then fasten the screws onto
the TV again.
✎✎ Screws may not be supplied with the product. In this case, please purchase the screws of the following specifications.
3. Connect the clamps fixed onto the TV and the clamps fixed onto the wall with a strong string and then tie the string
tightly.
✎✎ NOTE
• Install the TV near to the wall so that it does not fall backwards.
• It is safe to connect the string so that the clamps fixed on the wall are equal to or lower than the clamps fixed on
the TV.
• Untie the string before moving the TV.
4. Verify that all connections are properly secured. Periodically check connections for any sign of fatigue for failure. If you
have any doubt about the security of your connections, contact a professional installer.
Anti-theft Kensington Lock
The Kensington Lock is not supplied by Samsung. It is a device used to
physically fix the system when using it in a public place. The appearance
and locking method may differ from the illustration, depending on the
manufacturer. Refer to the manual provided with the Kensington Lock for
additional information on proper use.
1
To lock the product, follow these steps:
Please find the “K” icon on the rear of the TV. A kensington slot is beside the
“K” icon.
<Optional>
1. Wrap the Kensington lock cable around a large, stationary object such as
desk or chair.
2. Slide the end of the cable with the lock attached through the looped end of the Kensington lock cable.
3. Insert the locking device into the Kensington slot on the product (1).
4. Lock the lock.
✎✎ These are general instructions. For exact instructions, see the User manual supplied with the locking device.
✎✎ The locking device has to be purchased separately.
✎✎ The location of the Kensington Lock may be different depending on the model.
English
61
Specifications
Environmental Considerations
Operating Temperature
Operating Humidity
Storage Temperature
Storage Humidity
10°C to 40°C (50°F to 104°F)
10% to 80%, non-condensing
-20°C to 45°C (-4°F to 113°F)
5% to 95%, non-condensing
Model Name
HG28EC690
Display Resolution
1366 x 768
Stand Swivel (Left / Right)
Screen Size (Diagonal)
Sound (Output)
Dimensions (WxDxH)
Body
With stand
Weight
Without Stand
With Stand
Model Name
0˚
20˚ / 60˚ / 90˚
28 inches
32 inches
5W x 2
643.4 x 62.9 x 396.5 mm
643.4 x 163.4 x 435.1 mm
721.4 x 64.9 x 428.5 mm
721.4 x 192.6 x 465.6 mm
906.6 x 65.1 x 532.9 mm
906.6 x 226.5 x 577.6 mm
3.7 kg
4.1 kg
5.0 kg
6.4 kg
7.8 kg
10.7 kg
HG48EC690
HG55EC690
1920 x 1080
20˚ / 60˚ / 90˚
48 inches
Sound (Output)
Weight
Without Stand
With Stand
40 inches
10W x 2
Stand Swivel (Left / Right)
Dimensions (WxDxH)
Body
With stand
HG40EC690
1920 x 1080
Display Resolution
Screen Size (Diagonal)
HG32EC690
55 inches
10W x 2
1075.1 x 65.5 x 627.6 mm
1075.1 x 226.5 x 673.5 mm
1230.6 x 64.0 x 718.4 mm
1230.6 x 226.5 x 762.8 mm
11.1 kg
14.0 kg
15.7 kg
18.6 kg
✎✎Design and specifications are subject to change without prior notice.
✎✎For power supply and power consumption information, refer to the label attached to the product.
62
English
Dimensions
▪▪ Front view / Side view
HG28EC690
7
1
2
1
7
3
5
6
3
5
6
2
4
8
(Unit: mm)
HG28EC690
1
643.4
2
609.5
4
3
347.0
4
311.4
5
396.5
6
435.1
8
7
62.9
8
163.4
7
1
HG32EC690 / HG40EC690 / HG48EC690 / HG55EC690
7
1
2
2
3
5
6
3
5
6
8
4
8
4
(Unit: mm)
HG32EC690
1
721.4
2
700.4
3
394.8
4
450.8
5
428.5
6
465.6
7
49.1
8
192.6
HG40EC690
906.6
887.6
500.2
556.5
532.9
577.6
49.3
226.5
HG48EC690
1075.1
1056.1
594.9
556.5
527.6
673.5
49.7
226.5
HG55EC690
1230.6
1209.6
680.4
556.5
718.4
762.8
64.0
226.5
English
63
▪▪ Jack panel detail / Rear view
HG28EC690
(Unit: mm)
HG28EC690
1
2
3
4
5
6
7
8
100
100
271.7
140.5
147.3
78.7
113.5
392.4
HG32EC690 / HG40EC690 / HG48EC690 / HG55EC690
5
6
8
7
(Unit: mm)
1
2
3
4
5
6
7
8
HG32EC690
200
200
242.6
95.9
176.5
114.2
110.5
477.7
HG40EC690
200
200
284.7
124.0
195.4
156.3
196.9
620.8
HG48EC690
400
400
305.9
73.6
262.8
177.5
223.3
768.0
HG55EC690
400
400
356.8
150.2
336.0
228.2
238.1
872.8
64
English
▪▪ Base Stand detail
HG28EC690 / HG32EC690
(Unit: mm)
311.4
163.4
122.5
HG40EC690 / HG48EC690 / HG55EC690
(Unit: mm)
67
135
R9.5
R3.8
9.5
556.5
149.5
NOTE: All drawings are not necessarily to scale. Some dimensions are subject to change without prior notice. Refer to the
dimensions prior to performing installation of your TV. Not responsible for typographical or printed errors.
English
65
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care centre.
Country
AUSTRIA
BELGIUM
Customer Care Centre
0800 - SAMSUNG (0800 - 7267864)
02-201-24-18
BOSNIA
BULGARIA
CROATIA
051 331 999
07001 33 11 , sharing cost
062 726 786
CZECH
800 - SAMSUNG (800-726786)
www.samsung.com/cz/support
Samsung Electronics Czech and Slovak, s.r.o. V Parku 2343/24, 148 00 - Praha 4
DENMARK
FINLAND
FRANCE
GERMANY
70 70 19 70
030-6227 515
01 48 63 00 00
0180 6 SAMSUNG bzw.
0180 6 7267864*
[HHP] 0180 6 M SAMSUNG bzw.
(*0,20 €/Anruf aus dem dt. Festnetz, aus dem Mobilfunk
max. 0,60 €/Anruf)
8009 4000 only from landline, toll free
80111-SAMSUNG (80111 726 7864) only from land line
(+30) 210 6897691 from mobile and land line
0680SAMSUNG (0680-726-786)
0680PREMIUM (0680-773-648)
800-SAMSUNG (726-7864)
[HHP] 800.Msamsung (800.67267864)
261 03 710
020 405 888
080 697 267
090 726 786
0900-SAMSUNG (0900-7267864) (€ 0,10/Min)
815 56480
0 801-172-678* lub +48 22 607-93-33 **
[HHP] 0 801-672-678* lub +48 22 607-93-33**
*(całkowity koszt połączenia jak za 1 impuls według taryfy
operatora)
** (koszt połączenia według taryfy operatora)
808 20 7267
08008 SAMSUNG (08008 726 7864)
TOLL FREE No.
011 321 6899
CYPRUS
GREECE
HUNGARY
ITALIA
LUXEMBURG
MONTENEGRO
SLOVENIA
NETHERLANDS
NORWAY
POLAND
PORTUGAL
ROMANIA
SERBIA
SLOVAKIA
SPAIN
Web Site
www.samsung.com/at/support
www.samsung.com/be/support (Dutch)
www.samsung.com/be_fr/support (French)
www.samsung.com/support
www.samsung.com/bg/support
www.samsung.com/hr/support
www.samsung.com/dk/support
www.samsung.com/fi/support
www.samsung.com/fr/support
www.samsung.com/de/support
www.samsung.com/gr/support
http://www.samsung.com/hu/support
www.samsung.com/it/support
www.samsung.com/support
www.samsung.com/support
www.samsung.com/si/support
www.samsung.com/nl/support
www.samsung.com/no/support
www.samsung.com/pl/support
www.samsung.com/pt/support
www.samsung.com/ro/support
www.samsung.com/rs/support
www.samsung.com/sk/support
www.samsung.com/es/support
SWEDEN
SWITZERLAND
0800 - SAMSUNG (0800-726 786)
0034902172678
[HHP] 0034902167267
0771 726 7864 (SAMSUNG)
0848 726 78 64 (0848-SAMSUNG)
U.K
EIRE
LITHUANIA
LATVIA
ESTONIA
TURKEY
0330 SAMSUNG (7267864)
0818 717100
8-800-77777
8000-7267
800-7267
444 77 11
www.samsung.com/uk/support
www.samsung.com/ie/support
www.samsung.com/lt/support
www.samsung.com/lv/support
www.samsung.com/ee/support
www.samsung.com/tr/support
© 2014 Samsung Electronics Co., Ltd. All rights reserved.
www.samsung.com/se/support
www.samsung.com/ch/support (German)
www.samsung.com/ch_fr/support (French)
Download PDF