Samsung | PS43F4000AR | Samsung PS43F4000AR User Manual

Important Safety Instructions
Getting Started
Warning! Important Safety Instructions
user manual
(Please read the safety instructions below before installing and using the product.)
If you have any questions or comments relating to Samsung products,
please contact the SAMSUNG customer care centre.
For India Only
This marking on the product, accessories or literature indicates
that the product and its electronic accessories should not be
disposed of with other household waste at the end of their
working life. To prevent possible harm to the environment
or human health from uncontrolled waste disposal, please
separate these items from other types of waste and recycle
them responsibly to promote the sustainable reuse of material
1300 362 603
0800 SAMSUNG (0800 726 786)
(852) 3698 4698
1800 3000 8282
1800 266 8282
0800-112-8888 (Toll Free)
(021) 56997777
1-800-10-7267864 [PLDT]
1-800-8-7267864 [Globe landline
and Mobile]
02-4222111 [Other landline]
1 800 588 889
0800 100 100
0800-Samsung (72678)
• Theslotsandopeningsinthecabinetandinthebackorbottomareprovidedfornecessaryventilation.Toensurereliableoperationofthisapparatus,
• Donotplacethisapparatusnearoroveraradiatororheatregister,orwhereitisexposedtodirectsunlight.
• Donotplaceavesselcontainingwater(vasesetc.)onthisapparatus,asthiscanresultinariskoffireorelectricshock.
• Donotexposethisapparatustorainorplaceitnearwater(nearabathtub,washbowl,kitchensink,orlaundrytub,inawetbasement,orneara
• Makesuretopulloutthepowercordfromtheoutletbeforecleaning.
• Thisapparatususebatteries.Inyourcommunity,theremightberegulationsthatrequireyoutodisposeofthesebatteriesproperlytoprotectthe
• Donotoverloadwalloutlets,extensioncords,oradaptorsbeyondtheircapacity,sincethiscanresultinfireorelectricshock.
• Power-supplycordsshouldberoutedsothattheyarenotlikelytobewalkedonorpinchedbyitemsplaceduponoragainstthem.Payparticular
• Toprotectthisapparatusfromalightningstorm,orwhenitisleftunattendedandunusedforlongperiodsoftime,unplugitfromthewalloutletand
• BeforeconnectingtheACpowercordtotheDCadaptoroutlet,makesurethevoltagedesignationoftheDCadaptorcorrespondstothelocal
• Neverinsertanythingmetallicintotheopenpartsofthisapparatus.Doingsomaycreateadangerofelectricshock.
• Toavoidelectricshock,nevertouchtheinsideofthisapparatus.Onlyaqualifiedtechnicianshouldopenthisapparatus.
• Makesuretoplugthepowercordinuntilitisfirmlyinserted.Pullontheplug,notthecord,whenremovingthepowercordfromtheoutlet.Donot
• Ifthisappratusdoesnotoperatenormally-inparticular,ifthereareanyunusualsoundsorsmellscomingfromit-unplugitimmediatelyandcontact
• BesuretopullthepowerplugoutoftheoutletiftheTVistoremainunusedorifyouaretoleavethehouseforanextendedperiodoftime(especially
• Besuretocontactanauthorizedservicecenter,wheninstallingyoursetinalocationwithheavydust,highorlowtemperatures,highhumidity,
• Useonlyaproperlygroundedplugandreceptacle.
• Toturnofftheapparatuscompletely,youmustpullthepowerplugoutofthewallsocket.Consequently,thepowerplugshouldbereadilyaccessible
• Donotallowchildrentohangontotheproduct.
• Storetheaccessories(batteries,etc.)inalocationsafelyoutofthereachofchildren.
• Donotinstalltheproductinanunstablelocationsuchasashakyself,aslantedfloor,oralocationexposedtovibration.
• Donotdroporimpartashocktotheproduct.Iftheproductisdamaged,disconnectthepowercordandcontactaservicecenter.
• Tocleantheproduct,unplugthepowercordfromthepoweroutletandwipetheproductusingasoft,drycloth.Donotuseanychemicalssuch
• Donotexposetheapparatustodrippingorsplashing.
• Donotdisposeofbatteriesinafire.
• Donotshortcircuit,disassemble,oroverheatthebatteries.
• notshortcircuit,disassemble,oroverheatthebatteries.
• Thereisadangerofexplosionifyoureplacethebatterieswiththewrongtypeofbattery.Replaceonlywiththesameorequivalenttype.
Edit Channel
Broadcasting Menu
This remote control has Braille points on the Power, Channel, and Volume buttons and can be used by visually impaired persons.
You can edit or delete channels.
1. Go to Edit Channel screen.
2. Press the ▲/▼ buttons to select the desired channel, then press
the ENTERE button. The (c) mark indicates the channel you’ve
✎ You can select more than one channel.
✎ Press the ENTERE again to deselect the channel.
❑ Memorizing channels
Auto Tuning
Displays and selects the available video
Turns the TV on and off.
(depending on the country)
Automatically allocated programme numbers may not correspond to
actual or desired programme numbers. If a channel is locked, the PIN
input window appears.
Using the coloured and function buttons with the Edit Channel
❑ Using the Channel menu
Press to directly access to channels.
Channel List
Alternately select Teletext ON, Double, Mix or OFF.
Returns to the previous channel.
Cuts off the sound temporarily.
Adjusts the volume.
Changes channels.
Displays the main on-screen menu.
Displays the channel list on the screen.
Views the Media Play.
Quickly select frequently used functions.
Selects the HDMI mode directly.
Displays information on the TV screen.
Selects the on-screen menu items and changes the
values seen on the menu.
Returns to the previous menu.
Exit the menu.
P.MODE: Selects the picture mode.
P.SIZE: Selects the picture size.
: Sports Mode on or off.
Use these buttons according to the direction
on screen.
Use these buttons in a specific feature.
Installing batteries (Battery size: AAA)
The Channel List contains the channels your TV displays when you press
the channel button. You can view channel information, All or Favourites
1-5. Press ►(Mode) button to change the channel mode.
✎ When you press the CH LIST button on the remote control, Channel
List screen will be displayed at once.
Channel Mode
■ Edit Favourites: Set channels you watch frequently as favourites.
✎ For detailed information about using Edit Favourites, refer to “Edit
■ Favourites 1-5: Shows all favourite channels, arranged in up to five
groups. Each group has a separate screen.
✎ The TV displays Favourites 1-5 only if you have added favourites
using Edit Favourites.
■ All: Shows all currently available channels.
Schedule Manager
You can set a desired channel to be displayed automatically at the
intended time. In addition, you can view, modify or delete a channel you
have reserved to watch.
✎ You must set the current time first using the Time → Clock Set
function in the System menu to use this function.
1. Press the Schedule on the Schedule Manager screen. The Schedule
Viewing menu appears.
2. Press the ▲/▼/◄/► buttons to set each option menu.
■ Channel: Select the desired channel.
■ Repeat: Select Once, Manual, Sat~Sun, Mon~Fri or Everyday to
set at your convenience. If you select Manual, you can set the day you
✎ The (c) mark indicates the day you’ve selected.
■ Date: You can set the desired date.
✎ It is available when you select Once in Repeat.
■ Start Time: You can set the start time you want.
✎ If you want to edit or cancel a reserved schedule, select the reserved
schedule on Schedule Manager. Then press the ENTERE button
and select the Edit or Delete.
■ a Red (Change Number): Changes channel order on the channel list.
− E (Done): Completes changing the channel order.
■ b Green (Lock / Unlock): Lock a channel so that the channel cannot
be selected and viewed. / Unlock the channel that you locked.
✎ This function is available only when the Channel Lock is set to On.
✎ The PIN input screen appears. Enter your 4-digit PIN. Change the PIN
using the Change PIN option.
■ { Yellow (Delete): Deletes a channel from the channel list.
■ } Blue (Select All / Deselect All): Selects or deselects all channels
at once.
(Go To): Goes to channel directly by pressing numbers (0~9).
■ k (Page): Move to previous or next page.
■ T (Tools): Displays the option menu. The option menu items that
appear may differ depending on the channel status and type.
− Category: Changes the channel mode to All, Recently Viewed,
Most Viewed. The selected channel mode is displayed.
− Edit Favourites: Go to Edit Favourites screen directly.
− Rename channel: Assign a name of up to five characters to a
channel. For example, Food, Golf, etc. This makes it easier to find and
select the channel.
− Channel Info: Display details of the selected channel.
− Information: Display details of the selected programme.
Edit Favourites t
You can add, edit or delete favourite channels.
1. Go to Edit Favourites screen.
2. Press the ▲/▼ buttons to select the desired channel, and then press
ENTERE button.
3. Choose a specific favourite list among Favourites 1-5 using b
(Change Fav.) button, and then press the { (Add) button. The
selected channel has been added in Favourites 1-5.
✎ One favourite channel can be added in several of favourites among
Favourites 1-5.
[PF4000-AR]BN68-04871J-01ENG.indd 1
Selecting the Menu
Power off
R s
Function menu
TV Side Panel
Selecting a Source
TV Controller
The image is drawn by
facing the front side of
the TV.
Remote control sensor
Exits the menu when pressing the controller more than 1 second.
When selecting the function by moving the controller to the up/down/left/right directions, be sure not to press the controller. If you press it first, you
cannot operate it to move the up/down/left/right directions.
Setup (Initial Setup)
When you turn the TV on for the first time, a sequence of on-screen prompts will assist in configuring basic settings. Press the POWER button. Set the
initial setup following instructions that the TV guides.
Connecting the power cord and aerial. (refer to ‘Connections’)
VHF/UHF Aerial
Power Input
TV Rear Panel
The side panel may differ
depending on the model.
The PDP device may interfere with an amateur radio or AM radio.
When using two-way radio mobile and portable units or amateur
radio or AM radio near by your TV, this may cause the TV to
Audio connection
Amplifier / Home Theater
How to use Edit Name
Changing the Input Source
Edit Name lets you associate a device name to an input source. To
access Edit Name, press the TOOLS button in Source List. Name the
device connected to the input jacks to make your input source selection
Source List
Use to select TV or other external input sources such as DVD / Blu-ray
players / cable box / STB satellite receiver connected to the TV.
1. Press the SOURCE button.
2. Select a desired external input source.
■ TV / HDMI1 / HDMI2 / AV / Component
✎ You can only choose external devices that are connected to the TV.
In the Source, connected inputs are highlighted.
Using the coloured and function buttons with the Edit Favourites
■ a Red (Category / Change order)
− Category: Changes the channel mode to All, Recently Viewed,
Most Viewed. The selected channel mode is displayed.
− Change order: Changes the favourite channel order.
E (Done): Completes changing the channel order.
■ b Green (Change Fav.): Changes favourite list among Favourites 1-5.
■ { Yellow (Add / Delete)
− Add: Adds selected channels to Favourites 1-5.
− Delete: Deletes the favourite channel from Favourites 1-5.
■ } Blue (Select All / Deselect All) : Selects or deselects all channels
at once.
(Go To): Goes to channel directly by pressing numbers (0~9).
■ k (Page): Move to previous or next page.
■ T (Tools): Displays the option menu. The option menu items that
appear may differ depending on the channel status and type.
− Copy to favourites: Copy the selected favourite channel in
Favourites 1-5. You can add from other favourite list.
− Rename Favourites: Assign your own favourite channel name.
− Edit Channel: Go to Edit Channel screen directly.
− Information: Display details of the selected programme.
You can see detailed information about the selected external device.
Picture Menu
❑ Changing the Preset Picture Mode
Picture Mode t
Select your preferred picture type.
■ Dynamic: Suitable for a bright room.
■ Standard: Suitable for a normal environment.
■ Movie: Suitable for watching movies in a dark room.
Picture Options
You can watch the TV tuner and one external video source
simultaneously. PIP (Picture-in-Picture) does not function in the same
✎ If you turn the TV off while watching in PIP mode, the PIP window
will disappear.
✎ You may notice that the picture in the PIP window becomes slightly
unnatural when you use the main screen to view a game or karaoke.
■ Colour Tone
✎ Warm1 or Warm2 will be deactivated when the picture mode is
✎ Settings can be adjusted and stored for each external device
connected to an input on the TV.
■ Digital Clean View: If the broadcast signal received by your TV is
weak, you can activate the Digital Clean View feature to reduce any
static and ghosting that may appear on the screen.
✎ When the signal is weak, try other options until the best picture
is displayed.
Auto Visualisation: When changing analogue channels, displays
signal strength.
✎ Only available for analogue channels.
✎ When the INFO button is pressed, the signal strength bar is
✎ When bar is green, you are receiving the best possible signal.
■ MPEG Noise Filter: Reduces MPEG noise to provide improved
picture quality.
■ HDMI Black Level: Selects the black level on the screen to adjust the
screen depth.
■ Film Mode: Sets the TV to automatically sense and process film
signals from all sources and adjust the picture for optimum quality.
✎ Available in TV mode and external input mode which supports SD
(480i / 576i) and HD (1080i).
✎ If the screen does not seem natural, change its option to Off /
Auto1 / Auto2 in Film Mode.
■ Analog Clean View: Reduces diagonal noise in picture caused by the
crosstalk of signals.
PIP Settings
❑ Adjusting Picture Settings
Cell Light / Contrast / Brightness / Sharpness /
Colour / Tint (G/R)
Your television has several setting options for picture quality control.
✎ In analogue TV, AV modes of the PAL system, the Tint (G/R) function
is not available.
✎ Settings can be adjusted and stored for each external device
connected to the TV.
✎ Lowering picture brightness reduces power consumption.
❑ Other Features
Picture Size
Channel Settings
Set the various picture options such as picture size and aspect ratio.
✎ The available items may differ depending on the selected mode.
✎ Depending on the input source, the picture size options may vary.
■ Picture Size t: Your cable box/satellite receiver may have its
own set of screen sizes as well. However, we highly recommend you
use 16:9 mode most of the time.
− 16:9: Sets the picture to 16:9 wide mode.
− Wide Zoom: Magnifies the picture size more than 4:3.
✎ Adjusts the Position by using ▲, ▼ buttons.
− Zoom: Magnifies the 16:9 wide pictures vertically to fit the screen size.
✎ Adjusts the Zoom or Position by using ▲, ▼ button.
− 4:3: Sets the picture to basic (4:3) mode.
✎ Do not watch in 4:3 format for a long time. Traces of borders
displayed on the left, right and centre of the screen may cause
image retention (screen burn) which are not covered by the
− Screen Fit: Displays the full image without any cut-off when HDMI
(720p / 1080i / 1080p) or Component (1080i / 1080p) signals are
■ Zoom/Position: Adjust the picture size and position. It is only available
in Zoom.
■ Position: Adjust the picture position. It is only available in Screen Fit or
Wide Zoom.
✎ The available items may differ depending on the selected mode.
✎ Settings can be adjusted and stored for each external device
connected to an input on the TV.
✎ If you use the Screen Fit function with HDMI 720p input, 1 line will be
cut at the top, bottom, left and right as in the overscan function.
■ Area
(depending on the country)
You can change the desired area.
■ Manual Tuning
Scans for a channel manually and stores in the TV.
✎ If a channel is locked, the PIN input window appears.
✎ According to the channel source, Manual Tuning may be supported.
1. Press the New button.
2. Set the Programme, Colour System, Sound System, Channel and
3. Press the Store button. When scanning has finished, a channel is
updated in the channel list.
✎ Channel mode
− P (programme mode): When tuning is complete, the broadcasting
stations in your area have been assigned to the position numbers
from P0 to P99. You can select a channel by entering the position
number in this mode.
− C (aerial channel mode) / S or Z (cable channel mode) (depending
on the country): These two modes allow you to select a channel
by entering the assigned number for each aerial broadcasting
station or cable channel.
■ Fine Tune
If the signal is weak or distorted, fine tune the channel manually.
✎ Fine tuned channels are marked with an asterisk “*”.
✎ To reset the fine-tuning, select Reset.
■ Transfer Channel List
(depending on the country)
Imports or exports the channel map. You should connect a USB storage to
use this function.
✎ The PIN number input screen appears. Enter your 4 digit PIN number.
✎ Supported file systems are FAT and exFAT.
Input Source
Main picture
Sub picture
Component, HDMI
PIP: Activate or deactivate the PIP function.
Source: Select the source for the sub-screen.
Channel: Select the channel for the sub-screen.
Size: Select a size for the sub-picture.
Position: Select a position for the sub-picture.
Sound Select: You can choose the desired sound (Main / Sub) in
PIP mode.
❑ Changing the Picture Options
Advanced Settings
(available in Standard / Movie mode)
You can adjust the detailed setting for the screen including colour and
■ Dynamic Contrast: Adjust the screen contrast.
■ Black Tone: Select the black level to adjust the screen depth.
■ Flesh Tone: Adjust the flesh tone colour.
■ RGB Only Mode: Displays the Red, Green and Blue colour for
making fine adjustments to the hue and saturation.
■ Colour Space: Adjust the range of colours available to create the
■ White Balance: Adjust the colour temperature for a more natural
picture. R-Offset / G-Offset / B-Offset: Adjust each colour’s (red,
green, blue) darkness.
R-Offset / G-Offset / B-Offset: Adjust each colour’s (red, green,
blue) brightness.
R-Gain / G-Gain / B-Gain: Adjust each colour’s (red, green, blue)
Reset: Resets the White Balance to its default settings.
■ Gamma: Adjust the primary colour intensity.
■ Motion Lighting: Reduce power consumption by brightness control
adapted motion.
✎ Only available in Standard mode.
✎ When changing a setting value of Cell Light, Brightness or
Contrast, Motion Lighting will be set to Off.
Picture Off
The screen is turned off but the sound remains on. Press any button
except volume button to turn on the screen.
Reset Picture
Resets your current picture mode to its default settings.
Sound Menu
❑ Changing the Preset Sound Mode
Sound Mode
Standard: Selects the normal sound mode.
Music: Emphasizes music over voices.
Movie: Provides the best sound for movies.
Clear Voice: Emphasizes voices over other sounds.
Amplify: Increase the intensity of high-frequency sound to allow a
better listening experience for the hearing impaired.
Picture Size
Component(480i, 480p, 576i,
576p, 720p)
16:9, Wide Zoom, Zoom, 4:3
Component(1080i, 1080p)
HDMI(720p, 1080i, 1080p)
16:9, Wide Zoom, Zoom, 4:3, Screen Fit
16:9, Wide Zoom, Zoom, 4:3
16:9, Wide Zoom, Zoom, 4:3, Screen Fit
Lock channels in Channel menu to prevent unauthorized users, such as
children, from watching unsuitable programme.
✎ Available only when the Source is set to TV.
• Use the remote control within 23 feet from TV.
• Bright light may affect the performance of the remote control. Avoid using nearby special fluorescent light or neon signs.
• The Colour and shape may vary depending on the model.
Blu-ray player / DVD
Channel Lock
Component connection
The TV’s Controller, a small joy stick like button on the rear left side of the TV, lets you control the TV without the remote control.
- English -2-
Remote Control
AV connection
Selecting the Media Play
© 2013 Samsung Electronics Co., Ltd. All rights reserved.
HDMI connection
Set-top Box / Blu-ray players
TV Controller (Panel Key)
Web Site
Customer Care Centre
For personal and non-commercial use only.
Usage is subject to following the guidelines in the User Manual and
may not be available in all regions.
For more information on safe disposal and recycling visit our website or contact our Helpline numbers - 18002668282,
 Coaxial (RF)
 Screen Image retention
Do not display a still image (such as on a video game) on the plasma display panel
for more than several minutes as it can cause screen image retention. This image
retention is also known as “screen burn”. To avoid such image retention, reduce the
degree of brightness and contrast of the screen when displaying a still image.
 Heat on the top of the Plasma TV
The top side of the product may be hot after long periods of use as heat dissipates
from the panel through the vent hole in the upper part of the product.
This is normal and does not indicate any defect or operation failure of the product.
However, children should be prevented from touching the upper part of the product.
 The product is making a “cracking” noise.
A “cracking” noise may occur when the product contracts or expands due to a
change in the surrounding environment such as temperature or humidity. This is
normal and not a defect of the unit.
 Cell Defects
The PDP uses a panel consisting of 2,360,000(HD-level) to 6,221,000(FHD-level)
pixels which require sophisticated technology to produce. However, there may be
a few bright or dark pixels on the screen. These pixels will have no impact on the
performance of the product.
 Avoid operating the TV at temperatures below 41°F (5°C)
 A still image displayed too long may cause permanent damage to the PDP
Watching the Plasma TV in 4:3 format for a long period of time
may leave traces of borders displayed on the left, right and
centre of the screen caused by the difference of light emission
on the screen. Playing a DVD or a game console may cause
similar effects to the screen.
Damages caused by the above effect are not covered by the
 After-images on the Screen.
Displaying still images from Video games for longer than a certain period of time may
produce partial after-images.
To prevent this effect, reduce the “brightness” and “contrast” when displaying still
images for a long time.
 Warranty
Warranty does not cover any damage caused by image retention.
Burn-in is not covered by the warranty.
Input Cables (Sold Separately)
 Power Cord
 Composite (AV)
 Component
User Instructions
 Remote Control & Batteries (AAA x 2)
 Owner’s Instructions
 Warranty Card / Regulatory Guide (Not available in some locations)
 For better picture and audio quality, connect to a digital device using an HDMI
 For set-top box connection using HDMI cable, we highly recommend you to
connect the HDMI IN 1(STB) port.
 The picture may not display normally (if at all) or the audio may not work if an
 The TV model is not allowed for PC connection (distortion or incorrect picture
external device that uses an older version of HDMI mode is connected to the TV. If
displaying can appear).
such a problem occurs, ask the manufacturer of the external device about the HDMI
version and, if out of date, request an upgrade.
 Be sure to purchase a certified HDMI cable. Otherwise, the picture may not display
or a connection error may occur.
Plasma TV
Figures and illustrations in this User Manual are provided for reference only and
may differ from actual product appearance. Product design and specifications
may be changed without notice.
❑ Adjusting Sound Settings
Sleep Timer t
Sound Effect
Automatically shuts off the TV after a preset period of time. (30, 60, 90,
120, 150 and 180 minutes)
✎ Use the ▲/▼ buttons to select a period of time, and then press
ENTERE. To cancel the Sleep Timer, select Off.
(standard sound mode only)
■ DTS TruSurround: This function provides a virtual 5.1 channel
surround sound experience through a pair of speakers using HRTF
(Head Related Transfer Function) technology.
■ DTS TruDialog: This function allows you to increase the intensity of
a voice over background music or sound effects so that dialogue can
be heard more clearly.
■ Equaliser: Use Equaliser to customize sound setting for each
− Balance: Adjusts the balance between the right and left speaker.
− 100Hz / 300Hz / 1kHz / 3kHz / 10kHz: (Bandwidth Adjustment)
Adjusts the level of specific bandwidth frequencies.
− Reset: Resets the equaliser to its default settings.
On Timer / Off Timer
Speaker Settings
■ Auto Volume: To equalize the volume level on each channel, set to
Night: This mode provides an improved sound experience compared
to Normal mode, making almost no noise. It is useful at night.
✎ To use the volume control on the source device connected to the
TV, set Auto Volume to Off on the TV. Otherwise, a change to the
volume control of the source device may not be applied.
Reset Sound
Reset all sound settings to the factory defaults.
❑ Selecting the Sound Mode t
When you set to Dual I-II, the current sound mode is displayed on the
A2 Stereo
NICAM Stereo
Audio Type
Dual I-II
Stereo ↔ Mono
Dual I ↔ Dual II
Stereo ↔ Mono
Mono → Dual I
 Dual II 
Automatic change
Dual I
Automatic change
Dual I
If the stereo signal is weak and an automatic switching, occurs, then
switch to the mono.
Only activated in stereo sound signal.
Only available when the Source is set to TV.
System Menu
❑ Executing initial setup
Configure the channels and the time when setting up the TV for the first
time or when resetting the unit.
✎ Execute the initial setup following instructions that the TV guides.
✎ Enter your 4-digit PIN, the default of which is 0-0-0-0.
■ On Timer: You can set up three separate On Timer configurations.
(On Timer 1, On Timer 2, On Timer 3)
Setup: Select Off, Once, Everyday, Mon~Fri, Mon~Sat, Sat~Sun or
Manual to set at your convenience. If you select Manual, you can set
up the day you want to activate the timer.
✎ The c mark indicates the day you’ve selected.
Time: Set the hour and minute.
Volume: Set the desired volume level.
Source: To select the source of the content that will play when the TV
turns on. You can:
- Select TV and have the TV display a specific air or cable channel.
- Select USB and have the TV play back photo or audio files from a
USB device.
- Select a source on your TV that you have connected a set-top box
to, and have the TV display a channel from the set-top box.
✎ The USB device must be connected to your TV before you can
select USB.
✎ If you select a source other than TV or USB, you must:
 Have a cable or satellite set-top box attached to that source.
 Set the set-top box to the channel you want to watch when the
TV goes on.
 Leave the set-top box turned on.
✎ When you select a source other than TV Channel options will
Channel: (when the Source is set to TV) Select the desired channel.
Music / Photo: (when the Source is set to USB) Select a folder in the
USB device containing music or photo files to be played when the TV
is turned on automatically.
- If there is no music file on the USB device or the folder containing
a music file is not selected, the timer function does not operate
- When there is only one photo file in the USB device, the slide show
will not play.
- If a folder name is too long, the folder cannot be selected.
- Each USB you use is assigned its own folder. When using more
than one of the same type of USB, make sure the folders assigned
to each USB have different names.
- It is recommended that you use a USB memory stick and a multi
card reader when using On Timer.
- The On Timer function may not work with USB devices with a builtin battery, MP3 players, or PMPs made by some manufacturers
because these devices take a long time to be recognised.
■ Off Timer: You can set up three separate Off Timer configurations.
(Off Timer 1, Off Timer 2, Off Timer 3)
Setup: Select Off, Once, Everyday, Mon~Fri, Mon~Sat, Sat~Sun or
Manual to set at your convenience. If you select Manual, you can set
up the day you want to activate the timer.
✎ The c mark indicates the day you’ve selected.
Time: Set the hour and minute.
❑ Setting the Time
The current time will appear every time you press the INFO button.
■ Clock Set: Set the Date and Time.
✎ You can set the Date and Time directly by pressing the number
buttons on the remote control.
Menu Language
Change PIN
Set the menu language.
Eco Solution
■ Energy Saving: This adjusts the brightness of the TV in order to
reduce power consumption.
■ No Signal Power Off: To avoid unnecessary energy consumption, set
how long you want the TV to remain on if it’s not receiving a signal.
■ Auto Power Off: The TV will be automatically turned off when no user
operation is received for 4 hours.
✎ If the Auto Power Off option is set to Off, the TV will stay on even
if no operations are performed on the TV.
Screen Burn Protection
To reduce the possibility of screen burn, this unit is equipped with Pixel
Shift screen burn prevention technology. Pixel Shift moves the picture
slightly on the screen. Auto Protection Time function setting allows you
to programme the time between movement of the picture in minutes.
Your TV also has the following additional screen burn protection
■ Pixel Shift: Using this function, you can set the TV to move pixels
minutely on the PDP screen in a horizontal or vertical direction to
minimize after images on the screen.
✎ Available Pixel Shift Settings and Optimum Settings
Time (minute)
1~4 min
4 min
The wall mount kit (sold separately) allows you to mount the TV on
the wall. For detailed information on installing the wall mount, see the
instructions provided with the wall mount. Contact a technician for
assistance when installing the wall mount bracket. We do not advice you
to do it yourself.
Samsung Electronics is not responsible for any damage to the product
or injury to yourself or others if you select to install the TV on your own.
Wall Mount Kit Specifications (VESA)
Wall mount kit is not supplied but sold separately.
Install your wall mount on a solid wall perpendicular to the floor. When
attaching to other building materials, please contact your nearest dealer.
If installed on a ceiling or slanted wall, it may fall and result in severe
personal injury.
 Standard dimensions for wall mount kits are shown in the table below.
 When purchasing our wall mount kit, a detailed installation manual and all
parts necessary for assembly are provided.
 Do not use screws that do not comply with the VESA standard screw
 Do not use screws longer than the standard dimension, as they may cause
damage to the inside of the TV set.
 For wall mounts that do not comply with the VESA standard screw
specifications, the length of the screws may differ depending on their
Do not fasten the screws too strongly, this may damage the product or cause
the product to fall, leading to personal injury. Samsung is not liable for these
kinds of accidents.
Samsung is not liable for product damage or personal injury when a non-VESA
or non-specified wall mount is used or the consumer fails to follow the product
installation instructions.
Do not exceed 15 degrees tilt when mounting this TV.
VESA Spec. (A * B)
400 X 400
Standard Screw
Do not install your Wall Mount
Kit while your TV is turned on. It
may result in personal injury due
to electric shock.
Securing the Installation Space
Keep the required distances between the product and other objects (e.g. walls) to
ensure proper ventilation.
Failing to do so may result in fire or a problem with the product due to an increase in
the internal temperature of the product.
When using a stand or wall-mount, use parts provided by Samsung
Electronics only.
If you use parts provided by another manufacturer, it may result in a problem
with the product or an injury due to the product falling.
The appearance may differ depending on the product.
Be careful when you contact the TV because some parts can be somewhat
Caution: Pulling, pushing, or climbing onto the TV may cause the
TV to fall. In particular, ensure that your children do not hang over or
destabilize the TV; doing so may cause the TV to tip over, resulting in
serious injuries or death. Follow all safety precautions provided on the
included Safety Flyer. For added stability, install the anti-fall device for
safety purposes, as follows.
To avoid the TV from falling
1. Put the screws into the clamps and firmly fasten them onto the wall.
Confirm that the screws have been firmly installed onto the wall.
✎ You may need additional material such as an anchor depending
on the type of wall.
✎ Since the necessary clamps, screws, and string are not supplied,
please purchase these additionally.
2. Remove the screws from the centre back of the TV, put the screws
into the clamps, and then fasten the screws onto the TV again.
✎ Screws may not be supplied with the product. In this case, please
purchase the screws of the following specifications.
3. Connect the clamps fixed onto the TV and the clamps fixed onto the
wall with a strong string and then tie the string tightly.
✎ Install the TV near to the wall so that it does not fall backwards.
✎ It is safe to connect the string so that the clamps fixed on the wall
are equal to or lower than the clamps fixed on the TV.
✎ Untie the string before moving the TV.
4. Verify all connections are properly secured. Periodically check
connections for any sign of fatigue for failure. If you have any doubt
about the security of your connections, contact a professional
Anti-theft Kensington Lock
The Kensington Lock is not supplied by Samsung. It is a device used to
physically fix the system when using it in a public place. The appearance
and locking method may differ from the illustration depending on the
manufacturer. Refer to the manual provided with the Kensington Lock for
additional information on proper use.
✎ Please find a “K” icon on the rear of the TV. The Kensington slot is
beside the “K” icon.
✎ The position and colour may differ depending on the model.
To lock the product, follow these steps:
1. Wrap the Kensington lock cable around a large, stationary object
such as desk or chair.
2. Slide the end of the cable with the lock attached through the looped
end of the Kensington lock cable.
3. Insert the locking device into the Kensington slot on the product.
4. Lock the lock.
✎ These are general instructions. For exact instructions, see the User
manual supplied with the locking device.
✎ The locking device has to be purchased separately.
Installation with a stand.
Installation with a wall-mount.
10 cm
10 cm
10 cm
10 cm
10 cm
10 cm
Application Menu
❑ Using the Source List
Source List
✎ When you press the SOURCE button, Source screen will be
displayed at once.
You can only choose external devices that are connected to the TV.
In Source, connected inputs are highlighted.
For the detailed information, refer to “Changing the Input Source”.
Connecting a USB Device
1. Turn on your TV.
2. Connect a USB device containing photo, music and movie files to the
USB port on the side of the TV.
3. When USB is connected to the TV, popup window appears. You can
select the Photos, Videos or Music directly.
✎ It might not work properly with unlicenced multimedia files.
✎ Need-to-Know List before using Media Play
■ Game Mode: When connecting to a game console such as
PlayStation™ or Xbox™, you can enjoy a more realistic gaming
experience by selecting game mode.
✎ Precautions and limitations for game mode
 To disconnect the game console and connect another external
device, set Game Mode to Off in the setup menu.
 If you display the TV menu in Game Mode, the screen shakes
✎ Game Mode is not available in TV mode.
✎ After connecting the game console, set Game Mode to On.
Unfortunately, you may notice reduced picture quality.
✎ If Game Mode is On:
 Picture Mode is set to Standard and Sound Mode is set to
 MTP (Media Transfer Protocol) is not supported.
 Supported file systems are FAT and exFAT.
 Certain types of USB Digital camera and audio devices may not be compatible
with this TV.
 Media Play only supports sequential jpeg format.
 Media Play only supports USB Mass Storage Class (MSC) devices. MSC is a
Mass Storage Class Bulk-Only Transport device. Examples of MSC are Thumb
drives, Flash Card Readers (USB HUB are not supported). Devices should be
connected directly to the TV’s USB port.
Before connecting your device to the TV, please back up your files to prevent
them from damage or loss of data. SAMSUNG is not responsible for any data
file damage or data loss.
The HDD (Hard Disk Drive) connected to USB is not supported.
Do not disconnect the USB device while it is loading.
The higher the resolution of the image, the longer it takes to display on the
The maximum supported JPEG resolution is 15360 x 8640 pixels.
For unsupported or corrupted files, the “Not Supported File Format” message
is displayed.
The scene search and thumbnail functions are not supported in the Videos.
MP3 files with DRM that have been downloaded from a non-free site cannot
be played. Digital Rights Management (DRM) is a technology that supports
the creation, distribution and management of the content in an integrated and
comprehensive way, including the protection of the rights and interests of the
content providers, the prevention of the illegal copying of contents, as well as
managing billings and settlements.
PTP connection mode is fully available only with digital cameras. When
connecting a smartphone or tablet to the TV using PTP mode, it may not be
slide show.
Background Music
/ Mini Player
over 4000, the files and folders may not appear and some folders may not be
Disconnecting a USB Device
1. Press the SOURCE button.
2. Select a desired USB device, and then press the TOOLS button. The
Tools menu appears.
3. Select Disconnect USB Device, and then wait until the selected USB
device is disconnected. You can remove a USB device from the TV.
✎ To remove a USB device from the TV, we recommend use Disconnect
USB Device function.
Enjoy photos, music and movie files saved on a USB Mass Storage Class
(MSC) device.
1. Press the MEDIA.P button.
2. Press ◄/► button to select desired menu (Photos, Videos, Music),
then press the ENTERE button.
3. Press ◄/► button to select desired device, then press the ENTERE
button again.
4. Press the ▲/▼/◄/► button to select the desired file in the list, then
press the ENTERE button or ∂ (Play) button.
15360 X 8640
4096 X 4096
15360 X 8640
The MPO type file does not support Zoom, Rotate and Slide Show
Effect functions.
■ Videos
Repeat Mode
Picture Size
During playing a file, press the ▲/▼/◄/► button to select the desired
✎ When the option menu is not displayed, press the TOOLS button or
ENTERE button.
✎ You can also use ∂/∑/∫/π/µ buttons on the remote control
during playback.
✎ If you press the INFO button during playback, you can view the
playback information.
Playback menu
Previous / Next
Start Slide Show / Stop
Slide Show
Play / Pause
Previous / Next
Rewind / Fast forward
Search Titles: You can choose the other file
Search Time Bar: You can search the video
using ◄ and ► button at one minute interval or
entering the number directly.
It may not be supported depending on the
input source.
You can play movie files repeatedly.
You can adjust the picture size to your
Subtitle Settings: You can play the video with
subtitles. This function only works if the subtitles
are the same file name as the video.
Picture Mode / Sound Mode: You can adjust
the picture or sound setting.
Audio Language: You can change the audio
language if the video has more than one
Information: You can see detailed information
about the played file.
If video time information is unknown, play time and progress bar are
not displayed.
In this mode, you can enjoy movie clips contained on a Game, but you
cannot play the Game itself.
Solutions and Explanations
Picture Quality
First of all, please perform the Picture Test and confirm that your TV is properly displaying test image.
(go to MENU - Support - Self Diagnosis - Picture Test)
If the test image is properly displayed, the poor picture may caused by the source or signal.
 If you have an analogue cable/set top box, upgrade to a digital set top box. Use HDMI or Component cables to deliver
SD (Standard definition) picture quality.
 Cable/Satellite subscribers: Try digital stations from the channel line up.
 Aerial connection: Try digital stations after performing Auto tuning.
 Adjust the Cable/Set top box video output resolution to 480p.
 Make sure you are watching the TV at the minimum recommended distance based on the size and definition of the
 If you’re using a component connection, make sure the component cables are connected to the correct jacks. Incorrect
or loose connections may cause colour problems or a blank screen.
There is poor colour or brightness.
 Adjust the Picture options in the TV menu. (go to Picture Mode / Colour / Brightness / Sharpness)
 Adjust Energy Saving option in the TV menu. (go to MENU - System - Eco Solution - Energy Saving)
 Try resetting the picture to view the default picture settings. (go to MENU - Picture - Reset Picture)
There is a dotted line on the edge of the screen.
 If the picture size is set to Screen Fit, change it to 16:9.
 Change cable/satellite box resolution.
The picture is black and white.
When changing channels, the picture freezes or is
distorted or delayed.
Solutions and Explanations
Aerial (Air/Cable) Connection
The TV is not receiving all channels.
 Make sure the Aerial cable is connected securely.
 Please try Setup (Initial setup) to add available channels to the channel list. Go to MENU - System - Setup (Initial setup)
and wait for all available channels to be stored.
 Verify the Aerial is positioned correctly.
The picture is distorted: macro block error small
block, dots, pixelization
 Compression of video contents may cause picture distortion, especially on fast moving pictures such as sports and
action movies.
 A low signal can cause picture distortion. This is not a TV issue.
 HD channels will have black bars on either side of the screen when displaying up scaled SD (4:3) contents.
 Black bars on the top and bottom will appear during movies that have aspect ratios different from your TV.
 Adjust the picture size options on your external device or TV to full screen.
Plasma TV is making humming noise.
 Plasma TVs typically make a soft humming sound. This is normal. It’s caused by the electrical charges that are used to
create the images on the screen.
 If the humming sound is loud, you may have set the brightness on the TV too high. Try setting the brightness lower.
 You can also have loud humming if the back of your Plasma TV is too close to a wall or other hard surface. Also try
rerouting your connection cables.
 Improper installation of wall mount can create excessive noise.
Image Retention (Burn In) Issue.
 To minimize the possibility of screen burn, this unit is equipped with Pixel Shift screen burn reduction technology. Pixel
Shift lets you set the picture so it moves slightly up and down (Vertical Line) and side to side (Horizontal Dot). The
regular, slight movement of the picture reduces screen burn in.
The remote control does not work.
 Replace the remote control batteries with the poles (+/–) in the right direction.
 Clean the sensor’s transmission window on the remote.
 Try pointing the remote directly at the TV from 5~6 feet away.
 If you are using an AV composite input, connect the video cable (yellow) to the Green jack of component input 1 on the
The cable/set top box remote control doesn’t turn
the TV on or off, or adjust the volume.
 Programme the Cable/Set top box remote control to operate the TV. Refer to the Cable/Set top box user manual for the
 If connected with a cable box, please try to reset the cable box. Reconnect the AC cord and wait until the cable box
reboots. It may take up to 20 minutes.
 Set the output resolution of the cable box to 480p.
A “Mode Not Supported” message appears.
 Check the supported resolution of the TV, and adjust the external device’s output resolution accordingly.
There is a plastic smell from the TV.
 This smell is normal and will dissipate over time.
TV is tilted to the right or left side.
 Remove the stand base from the TV and reassemble it.
There are difficulties assembling the stand base.
 Make sure the TV is placed on a flat surface. If you can not remove the screws from the TV, please use a magnetized
screw driver.
The Broadcasting menu is grey out (unavailable).
 The Broadcasting menu is only available when the TV source is selected.
Your settings are lost after 30 minutes or every
time the TV is turned off.
 If the TV is in the Store Demo mode, it will reset audio and picture settings every 30 minutes. If you want to change the
settings from Store Demo mode to Home Use, press the SOURCE button to select TV mode, and go to MENU →
Support → Use Mode.
 Check the cable connections. Make sure a video cable is not connected to an audio input.
 For aerial or cable connections, check the signal strength. Low signal level may cause sound distortion.
You have intermittent loss of audio or video.
 Check the cable connections and reconnect them.
 Loss of audio or video can be caused by using overly rigid or thick cables. Make sure the cables are flexible enough for
long term use. If mounting the TV to the wall, we recommend using cables with 90 degree connectors.
 Make sure the AC power cord is securely plugged in to the wall outlet and the TV.
 Make sure the wall outlet is working.
 Try pressing the POWER button on the TV to make sure the problem is not the remote. If the TV turns on, refer to “The
remote control does not work” below.
You see small particles when you look closely at
the edge of the frame of the TV.
 This is part of the product’s design and is not a defect.
The PIP menu is not available.
 PIP functionality is only available when you are using a HDMI or components source.
The TV turns off automatically.
 Ensure the Sleep Timer is set to Off in the Time menu.
 Make sure the AC power cord is plugged in securely to the wall outlet and the TV.
 When watching TV from an aerial or cable connection, the TV will turn off after 10 ~ 15 minutes if there is no signal.
You turned the TV off 45 minutes ago, and it
turned on again.
 It is normal. The TV operates the OTA (Over The Aerial) function itself to upgrade firmware downloaded whilst your
watching TV.
There are recurrent picture/sound issues.
 Check and change the signal/source.
You can not play 3D videos in some of the BD
 Take out the disk from player and put it again, or restart the BD player.
 To prevent this, use felt pads on any surface of the TV that comes in direct contact with furniture.
There is no picture/video.
 Check cable connections (remove and reconnect all cables connected to the TV and external devices).
 Set your external device’s (Cable/Set top Box, DVD, Blu-ray etc) video outputs to match the connections to the TV input.
For example, if an external device’s output is HDMI, it should be connected to an HDMI input on the TV.
 Make sure your connected devices are powered on.
 Be sure to select the TV’s correct source by pressing the SOURCE button on the remote control.
 Reboot the connected device by reconnecting the device’s power cable.
A reaction may occur between the rubber cushion
pads on the base stand and the top finish of
some furniture.
The message “This file may not be playable
properly.” appears.
 This may appear because of high bit rate of content. Content generally will play but could experience some playability
First of all, please perform the Sound Test to confirm that your TV audio is properly operating.
(go to MENU - Support - Self Diagnosis - Sound Test)
If the audio is ok, the sound problem may be caused by the source or signal.
There is no sound or the sound is too low at
maximum volume.
 Please check the volume of the device (Cable/Sat Box, DVD, Blu-ray etc) connected to your TV.
The picture is good but there is no sound.
 If you are using an external device, make sure the audio cables are connected to the correct audio input jacks on the TV.
 If you are using an external device, check the device’s audio output option (ex. you may need to change your cable box’s
audio option to HDMI when you have a HDMI connected to your TV).
 Reboot the connected device by reconnecting the device’s power cable.
The speakers are making an inappropriate noise.
No Picture, No Video
The TV will not turn on.
*.avi / *.mkv
*.asf /
*.mp4 /
*.vro /
/ *.ts
*.tp / *.trp
*.mov / *.flv
*.vob / *.svi
- 14-
rate (fps)
Bit rate
1920 x 1080
H.264 BP/
Motion JPEG
DTS (Core)
G.711(ALaw, μ-Law)
1920 x 1080
Videos/Music/Photos Play Option menus
When playing a file, select the Options.
640 x 480
Window Media
Video v9
.sub or .txt
SubStation Alpha
SubStation Alpha
MPEG-4 Timed
Text Format
Text Format
Text Format
Text Format
You can play music files repeatedly.
You can play the music randomly.
Sound Mode
You can adjust the sound setting.
Only displays the files with supported music file extension. Other file
extensions are not displayed, even if they are saved on the same
USB device.
✎ If the sound is abnormal when playing music files, adjust the
Equaliser in the Sound menu. (An over-modulated music file may
cause a sound problem.)
 Supported Music Formats
File Extension
MPEG1 Audio
Layer 3
*.m4a / *.mpa /
Supports up to 2ch.
Supports up to 2ch.
WMA 10 Pro supports up to 5.1 channel
and M2 profile. (WMA lossless audio is not
Format the USB device.
for PDP 4100 series
Delete the files in the USB device.
The Software Update menu lets you upgrade your TV’s software to the
latest version.
Current version: This is the software version already installed in the TV.
✎ When software is upgraded, video and audio settings you have
made will return to their default settings. We advise you to write
down your settings so that you can easily reset them after the
■ Update now
By USB: Insert a USB drive containing the firmware upgrade file,
downloaded from “” into the TV.
✎ Please be careful not to disconnect the power or remove the USB
drive until upgrades are complete. The TV will be turned off and
on automatically after completing the firmware upgrade.
Use Mode
Select the Use Mode suitable for your place. We strongly recommend
you select Home Use.
■ Home Use: Home Use is the default setting.
■ Store Demo: Store Demo is for retail environments only. If you select
Store Demo, some functions will not work, and the picture settings
will be reset every 30 minutes.
View this information when your TV does not work properly or when you
want to upgrade the software. You can find information regarding our call
centres, and how to download products and software.
Device Format
for PDP 4100 series
Contact Samsung
*.mid / *.midi
Software Update
■ Music
Set the encoding language if the
text you want to view does not
appear correctly.
Self Diagnosis
MPEG-4 timed text
Micro DVD
SubStation Alpha
SubStation Alpha
■ Picture Test: Use to check for picture problems. If the problem
continues to occur, check the colour pattern.
■ Sound Test: Use the built-in melody sound to check for sound
■ Reset: Reset all settings to the factory defaults.
✎ The PIN input screen appears before the setup screen.
✎ Enter your 4-digit PIN. Change the PIN using the Change PIN
 Supported Subtitle Formats
File extension
Support Menu
 WMA 10 Pro supports up to 5.1
channel and M2 profile.
 WMA lossless audio is not supported.
 Vorbis supports up to 2ch.
 DD+ supports up to 5.1 channel.
(depending on the country)
This mode provides optimised condition for watching sports games.
✎ When the sports mode is on, the picture and sound modes are set
to Stadium automatically.
✎ If you turn the TV off while watching Sports Mode, the Sports
Mode will be disable.
Audio decoder
Copy the files to the other USB
Sports Mode
 Video content will not play, or not play correctly, if there is an error in the
content or the container.
 Sound or video may not work if the contents have a standard bit rate/frame
rate above the compatible Frame/sec listed in the table.
 If the Index Table is in error, the Seek (Jump) function is not supported.
 Some USB/digital camera devices may not be compatible with the player.
 The menu can be displayed late if the video is over 10Mbps(bit rate).
Video decoder
for PDP 4100 series
❑ Using the Sports Mode
Other Restrictions
 Supports up to H.264, Level 4.1 (FMO/
ASO/RS are not supported.)
 frame rate :
- Below 1280 x 720: 60 frame max
- Above 1280 x 720: 30 frame max
 VC1 AP L4 is not supported.
 GMC 2 or higher is not supported.
type 0 and type 1
- 12 -
Storage and Maintenance
✎ If you remove the attached sticker on the TV screen, clean the residues and then watch TV.
Clean the product with a soft cloth
dampened with in a small amount of
water. Do not use a flammable liquid
(e.g. benzene, thinners) or a cleaning
Do not spray water directly onto the
product. Any liquid that goes into the
product may cause a failure, fire, or electric
You can keep your TV as optimum condition upgrading the latest firmware on web site ( → Support) by USB.
- 15 -
For DTS patents, see
Manufactured under license from DTS Licensing Limited.
DTS, the Symbol, & DTS and the Symbol together
are registered trademarks and DTS Studio Sound is a
trademark of DTS, Inc. © DTS, Inc. All Rights Reserved.
DivX Certified® to play DivX® video up to HD 1080p,
including premium content.
ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, LLC, a
subsidiary of Rovi Corporation. This is an official DivX Certified® device that plays
DivX video. Visit divx. com for more information and software tools to convert your
files into DivX videos. ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified®
device must be registered in order to play purchased DivX Video-on-Demand
(VOD) movies. To obtain your registration code, locate the DivX VOD section in your
device setup menu. Go to vod. for more information on how to complete
your registration. Covered by one or more of the following U.S. patents : 7,295,673;
7,460,668; 7,515,710; 7,519,274 DivX®, DivX Certified® and associated logos are
trademarks of Rovi Corporation or its subsidiaries and are used under license.
The terms HDMI and HDMI High-Definition Multimedia
Interface, and the HDMI Logo are trademarks or
registered trademarks of HDMI Licensing LLC in the
United States and other countries.
Open Source License Notice
In the case of using open source software, Open Source Licenses are available on
the product menu. Open Source License Notice is written only English.
Manufactured under license from Dolby Laboratories.
Dolby and the double-D symbol are trademarks of Dolby
For DTS patents, see
Manufactured under license from DTS Licensing Limited.
DTS, the Symbol, & DTS and the Symbol together are
registered trademarks, and DTS Premium Sound is a
trademark of DTS, Inc. © DTS, Inc. All Rights Reserved.
Environmental Considerations
Operating Temperature
Operating Humidity
Storage Temperature
Storage Humidity
Model Name
Display Resolution
Screen Size
Dimensions (W x H x D)
With stand
Without Stand
With Stand
- 13 -
Media Play - Additional Functions
Video Codec
The picture will not display in full screen.
 Compression of video contents may cause picture distortion especially in fast moving pictures such as sports and action
 Low signal level or bad quality can cause picture distortion. This is not a TV issue.
 Mobile phones used close to the TV (cca up to 1m) may cause noise in picture on analogue and digital TV.
Colour is wrong or missing.
Sound Quality
- 11 -
10 cm
[PF4000-AR]BN68-04871J-01ENG.indd 2
*.jpg / *.jpeg
Playing the Photos / Videos / Music
You can set background music when watching
a slide show. / You can control simple playback
Picture Mode / Sound Mode: You can adjust
the picture or sound setting.
Information: You can see detailed information
about the played file.
File Extension
1. Press the ▲ button to select Options at the top of each main screen
and select Play Selected.
2. Select the desired files.
✎ The check box appears to the left of the selected files.
✎ Press ENTERE button again to deselect the file.
3. Press the ▲ button to select Play.
✎ You can select or deselect all files pressing the Select All /
Deselect All.
You can rotate images in full screen mode.
During the slide show, all files in the file list will be displayed in order.
When you press the ∂ (Play) button (or ▲ button → Options →
Slide Show) in the file list, slide show will be started immediately.
✎ During the slide show, you can adjust the slide show speed using π
(REW) or µ (FF) button.
 Supported Photo Formats
Playing the selected files
You can zoom into images in full screen mode.
Using the Media Play
The picture is distorted: macroblock error, small
block, dots, pixelization
Slideshow Settings You can set the Speed and Effects during the
 If a file deleted from the PC is still found when Media Play is run, use the “Empty
the Recycle Bin” function on the PC to permanently delete the file.
 If the number of files and folders saved on a USB storage device is approximately
If the TV seems to have a problem, first try this list of possible problems and solutions. If none of these troubleshooting tips apply, visit “
com”, then click on Support, or call Samsung customer service centre.
The TV image does not look as good as it did in
the store.
* When setting the Background Music to Mini Player in Photos, these
buttons appear.
Shows the registration code authorized for the TV. If you connect to
the DivX web site and register with 10-digit registration code, you can
download the VOD activation file.
Once you play it using Videos, the registration is completed.
✎ For more information on DivX® VOD, visit
 Supported Video Formats
Setting menu
■ Photos
device is corrupted or a file in the list is not played, connect the USB device to
the PC, format the device and check the connection.
DivX® Video On Demand
- 10 -
Securing the TV to the Wall
Installing the Wall Mount
Change your password required to set up the TV.
✎ The PIN input screen appears before the setup screen.
✎ Enter your 4-digit PIN. Change the PIN using the Change PIN
❑ Using the Media Play
The Pixel Shift value may differ depending on the monitor size
(inches) and mode.
✎ This function is not available in the Screen Fit mode.
■ Auto Protection Time: If the screen displays a still image for a certain
period of time you define, the TV activates the screen saver to prevent
the formation of burnt in ghost images on the screen.
■ Scrolling: This function removes after-images on the screen by
illuminating all the pixels on the PDP according to a pattern. Use
this function when there are after images or symbols on the screen,
especially when you displayed a still image on the screen for a long
✎ The after-image removal function has to be executed for a long
time (approximately 1 hour) to effectively remove after-images on
the screen. If the after-image is not removed after you apply the
function, repeat the function again.
✎ Press any key on the remote control to cancel this feature.
■ Side Grey: When you watch TV with the screen ratio set to 4:3, using
the Side Grey function can prevent damage to the edges of the
screen by adjusting the white balance on the extreme left and right
Other Information
 A USB device that requires high power (more than 500mA or 5V) may not be
 If the TV has been no input during time set in Auto Protection Time, the screen
saver will run.
 The power-saving mode of some external hard disk drives may be released
automatically when connected to the TV.
 If a USB extension cable is used, the USB device may not be recognised or the
files on the device may not be read.
 If a USB device connected to the TV is not recognised, the list of files on the
■ Panel Lock: Lock or unlock all the keys on the panel.
■ Boot Logo: Display Samsung logo when the TV is turned on.
❑ Other Features
10 to 40 (50 to 104 )
10% to 80%, non-condensing
-20 to 45 (-4 to 113 )
5% to 95%, non-condensing
852 X 480
109 cm
1024 X 480
129 cm
10W X 2
10W x 2
100.7 X 61.6 X 5.5 (cm)
100.7 X 67.0 X 26.1 (cm)
118.5 x 70.2 x 5.5 (cm)
118.5 x 75.6 x 26.1 (cm)
13.6 kg
14.8 kg
17.6 kg
18.8 kg
Design and specifications are subject to change without prior notice.
For information about the power required and more about power consumption, refer to the label attached to the product.
- 16 -
Download PDF