Samsung | PS50A450P1 | Samsung PS42A450P1 User Manual

Contact SAMSUNG WORLD-WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG
customer care centre.
Country
AUSTRALIA
CHINA
HONG KONG
INDIA
INDONESIA
JAPAN
MALAYSIA
New zealand
PHILIPPINES
SINGAPORE
SOUTH AFRICA
TAIWAN
THAILAND
TURKEY
U.A.E
VIETNAM
Customer Care Centre 
1300 362 603
800-810-5858
010-6475 1880
3698-4698
3030 8282
1800 110011
0800-112-8888
0120-327-527
1800-88-9999
0800SAMSUNG(726-7864)
1800-10-SAMSUNG(726-7864)
1800-SAMSUNG(726-7864)
0860-SAMSUNG(726-7864 )
0800-329-999
1800-29-3232
02-689-3232
444 77 11
800-SAMSUNG (726-7864)
8000-4726
1 800 588 889
Web Site
www.samsung.com
www.samsung.com
www.samsung.com/hk
www.samsung.com
www.samsung.com
www.samsung.com/jp
www.samsung.com/my
www.samsung.com/nz
www.samsung.com/ph
www.samsung.com
www.samsung.com
www.samsung.com/tw
Plasma TV
user manual
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service, please
register your product at
www.samsung.com/global/register
Model
Serial No.
BN68-01445A-00
책1.indb 1
2008-03-17 오후 4:21:06
User Instructions
 Screen Image retention
Do not display a still image (such as on a video game or when hooking up a PC to this PDP) on the
plasma monitor panel for more than 2 hours as it can cause screen image retention. This image
retention is also known as “screen burn”. To avoid such image retention, reduce the degree of
brightness and contrast of the screen when displaying a still image.
 Height
The PDP can normally operate only under 2000m in height. It might abnormally function at a place
over 2000m in height so do not install and operate there.
 Heat on the top of the PDP TV
The top side of the product may be hot after long period of use as heat dissipates from the panel
through the vent hole in the upper part of the product. This is normal and does not indicate any defect
or operation failure of the product. However, children should be prevented from touching the upper
part of the product.
 The product is making a ‘cracking’ noise.
A ‘cracking’ noise may occur when the product contracts or expands due to a change of surrounding
environment such as temperature or humidity. This is normal and not a defect of the unit.
 Cell Defects
The PDP uses a panel consisting of 1,230,000(SD-level) to 3,150,000(HD-level) pixels which require
sophisticated technology to produce. However, there may be few bright or dark pixels on the screen.
These pixels will have no impact on the performance of the product.
 Avoid operating the TV at temperatures below 5°C(41°F)
 A still image displayed too long may cause permanent damage to the PDP Panel.
Watching the PDP TV in 4:3 format for a long period of time may leave traces
of borders displayed on the left, right and centre of the screen caused by the
difference of light emission on the screen. Playing a DVD or a game console
may cause similar effect to the screen. Damages caused by the above effect are
not covered by the Warranty.
 Afterimage on the Screen.
Displaying still images from Video games and PC for longer than a certain period of time may
produce partial afterimages. To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when
displaying still images.
 Warranty
- Warranty does not cover any damage caused by image retention.
- Burn-in is not covered by the warranty.
 Installation
Be sure to contact an authorized service centre, when installing your set in a location with heavy
dust, high or low temperatures, high humidity, chemical substance and where it operates continually
such as the airport, the train station etc. Failure to do so may cause a serious damage to your set.
© 2008 Samsung Electronics Co., Ltd. All rights reserved.
English - 책1.indb 2
2008-03-17 오후 4:21:06
General Information
PC Display
 User Instructions.............................................. 2
 Checking Parts................................................. 4
 Using the Stand-Base...................................... 4
 Control Panel .................................................. 5
 Connection Panel............................................. 6
 Viewing the Remote Control ........................... 8
 Setting up Your PC Software
(Based on Windows XP)................................ 30
 Input Mode (PC)............................................. 31
 Setting the PC................................................ 32
About Anynet+
 Switching Your Television On and Off.............. 9
 Viewing the Menus........................................... 9
 Plug & Play Feature....................................... 10
 Using the TOOLS Button............................... 11
 Viewing External Signal Sources................... 12
 Editing Device Names.................................... 13
 What is Anynet+? . ........................................ 33
 Connecting Anynet+ Devices......................... 33
 Setting Up Anynet+........................................ 34
 Scanning and Switching between Anynet+
Devices.......................................................... 34
 Recording....................................................... 35
 Listening through a Receiver......................... 36
 Check Points before Requesting Service...... 36
Channel Control
Appendix
Operation
 Storing Channels Automatically..................... 13
 Storing Channels Manually............................ 14
 Adding / Locking Channels............................ 15
 Sorting the Stored Channels.......................... 16
 Assigning Names to Channels....................... 16
 Fine Tuning Channel Reception..................... 17
English
Contents
 Teletext Feature (depending on the model)... 37
 Wall Mount Kit Specifications (VESA)............ 39
 Wall- mount adjustment (Sold separately)..... 40
 How to assemble the Stand-Base
(depending on the model).............................. 41
 Troubleshooting............................................. 42
 Specifications................................................. 43
Picture Control
 Changing the Picture Standard...................... 17
 Customizing the Picture Settings................... 18
 Configuring Detailed Settings on the Picture18
 Picture Options.............................................. 20
 Resetting the Picture Settings to the Factory
Defaults.......................................................... 24
Sound Control
 Sound Features............................................. 24
 Selecting the Sound Mode
(depending on the model).............................. 26
 Connecting Headphones (Sold separately)... 26
Function Description
 Time Features................................................ 27
 Language / Light Effect / Melody /
Entertainment / Energy Saving...................... 28
 Viewing the Picture in Picture (PIP)............... 29
☛
➢
Important
Note
Symbols
Press
English - 책1.indb 3
2008-03-17 오후 4:21:06
Checking Parts
Owner’s Instructions
Remote Control/
AAA Batteries
Power Cord
Cloth-Clean
Warranty Card/
Registration Card/
Safety Guide Manual
(Not available in all locations)
Cover-Bottom /
Screws (2ea)
(Refer to page 41)
Ferrite Core for
Power Cord
Ferrite Core for
Headphone
(Not available in all locations)
Sold Separately
S-Video Cable
Antenna Cable
Component Cables
Audio Cables
PC Cable
PC Audio Cable
HDMI Cable
HDMI/DVI Cable
Video Cable
Core (Power Cord, Headphone)
➢ Ferrite
The ferrite cores are used to shield the cables from interference.
When connecting a cable, open the ferrite core and clip it around the cable near
the plug.
Using the Stand-Base
or more people should carry
➢  Two
the PDP. Never lay the PDP on the
floor because of possible damage
to the screen. Always keep the
PDP upright.
 The PDP can rotate 20 degrees in
right and left directions.
-20° ~ 20°
English - 책1.indb 4
2008-03-17 오후 4:21:09
Control Panel
Front Panel
➢ The product colour and shape may vary depending on the model.
1 SOURCE
Toggles between all the available
input sources (TV, AV1, AV2, S-Video,
Component1, Component2, PC, HDMI1,
HDMI2, HDMI3).
➢ In the on-screen menu, use this button
as you would use the ENTER button on
the remote control.
2 MENU
Press to see an on-screen menu of your
TV’s features.
3 + VOL –
Press to increase or decrease the volume.
In the on-screen menu, use the + VOL
– buttons as you would use the ◄ and ►
buttons on the remote control.
4
CH
Press to change channels.
In the on-screen menu, use the
CH
buttons as you would use the ▲ and ▼
buttons on the remote control.
5 Power Indicator
6
Blinks and turns off when the power is on and
lights up in stand-by mode.
POWER
Press to turn the TV on and off.
7 Remote Control Sensor
Aim the remote control towards this spot on
the TV.
8 Speakers
English - 책1.indb 5
2008-03-17 오후 4:21:10
Connection Panel
Side Panel
1
2
or
3
➢ The product colour and shape may vary depending on the model.
you connect an audio or video system to your set, ensure that all elements are
☛  Whenever
switched off.
 When connecting an external device, match the colour of the connection terminal to the cable.
1 HDMI IN 3
Connect to the HDMI jack of a device with
HDMI output.
2 AV IN 2(S-VIDEO or VIDEO / AUDIO R/L)
Video (S-Video or Video) and Audio inputs for
external devices, such as a camcorder or VCR.
3 Headphones jack
You can connect a set of headphones if you
wish to watch a television programme without
disturbing the other people in the room.
Prolonged use of headphones at a high
volume may damage your hearing.
➢
Continued...
English - 책1.indb 6
2008-03-17 오후 4:21:11
Rear Panel
1
or
Cable Television
Network
9
2
4
or
8
7
6
3
5
➢ The product colour and shape may vary depending on the model.
☛  Whenever you connect an audio or video system to your set, ensure that all elements are switched off.
 When connecting an external device, match the colour of the connection terminal to the cable.
1 ANT IN
75Ω Coaxial connector for Aerial/Cable Network.
2 SERVICE
− Connector for service.
− Connect the serial jack between the
electro-motion wall mount bracket and your
TV when you want to adjust the TV viewing
angle using your remote control.
3 Connecting external Audio Devices
Connect RCA audio signals from the TV to an
external source, such as Audio equipment.
43D SYNC OUT
Connect to 3D IR Emitter
5 COMPONENT IN 1, COMPONENT IN 2
Audio (AUDIO L/R) and video (Y/PB/PR) inputs
for Component.
6 PC IN(PC) / AUDIO
Connect to the video and audio output jack on your PC.
7 AV IN 1(VIDEO / AUDIO R/L)
Connect RCA cable to an appropriate external
A/V device such as VCR, DVD or Camcorder.
8 HDMI IN 1, 2
- No additional Audio connection is needed for an
HDMI to HDMI connection.
- When using an HDMI/DVI cable connection, you
must use the HDMI IN 2 jack.
is HDMI?
➢ What
- “High Definition Multimedia interface” allows
the transmission of high definition digital
video data and multiple channels of digital
audio.
- The HDMI/DVI terminal supports DVI
connection to an extended device with
the appropriate cable (not supplied). The
difference between HDMI and DVI is that the
HDMI device is smaller in size, has the HDCP
(High Bandwidth Digital Copy Protection)
coding feature installed, and supports multi
- channel digital audio.
DVI IN (HDMI 2) AUDIO R/L
DVI audio outputs for external devices.
9 POWER IN
Connect the supplied power cord.
Supported modes for HDMI/DVI and Component
480i
480p
576i
576p
720p
1080i
HDMI/DVI 50Hz
X
X
X
O
O
O
HDMI/DVI 60Hz
X
O
X
X
O
O
Component
O
O
O
O
O
O
English - 책1.indb 7
2008-03-17 오후 4:21:15
Viewing the Remote Control
1 POWER button
(turns the TV on and off)
2 Selects the TV mode directly
3 Number buttons for direct
channel access
4 One/Two-digit channel
selection
5 Temporary sound switch-off
6
Volume increase
Volume decrease
7 Channel control button
(Refer to page 15)
8 Use to quickly select
frequently used functions.
9 Control the cursor in the
menu
0 Use to see information on
the current broadcast
# Press to select the optional
display and sound modes for
sports, cinema and games.
$ VCR/DVD Function (Rewind,
Stop, Play/Pause, Fast/
Forward)
% Available source selection
^ Previous channel
&
Next channel
Previous channel
* Displays the main on-screen
menu
( TruSurround XT mode
button
) Returns to the previous
menu
a Exit the on-screen menu
b Picture size selection
c DMA (Digital Media Adapter)
Use this when connecting
a Samsung DMA device
through an HDMI interface
and switching to DMA mode.
For more information on the
operating procedures, refer
to the user manual of the
DMA.
T his button is available when
“Anynet+ (HDMI-CEC)” is
“On”. (Refer to page 34)
d Selects the HDMI mode
directly.
e Picture effect selection
(Refer to page 17)
➢
Teletext Functions
(Refer to page 37)
2 Exit from the teletext display
(depending on the model)
7 Teletext store
8 Teletext size
0 Teletext reveal
! Fastext topic selection
@ Teletext display/mix both
teletext information and the
normal broadcast
% Teletext mode selection
(LIST/FLOF)
^ Teletext sub page
& P :Teletext next page
P :Teletext previous page
* Teletext index
) Teletext hold
a Teletext cancel
Continued...
English - 책1.indb 8
2008-03-17 오후 4:21:16
Installing Batteries in the Remote Control
1
2
3
Lift the cover at the back of the remote control upward as
shown in the figure.
Install two AAA size batteries.
Make sure to match the “+” and “–” ends of the
batteries with the diagram inside the compartment.
Do not mix battery types, i.e. alkaline and manganese.
Close the cover as shown in the figure.
Remove the batteries and store them in a cool and dry
place if you won’t be using the remote control for a long
time. The remote control can be used up to about 23 feet from the TV.
➢
➢
remote control doesn’t work! Check the following:
➢If1.the
Is the TV power on?
2. Are the plus and minus ends of the batteries reversed?
3. Are the batteries drained?
4. Is there a power cut, or is the power cord unplugged?
5. Is there a special fluorescent light or a neon sign nearby?
Switching Your Television On and Off
The mains lead is attached to the rear of the television.
1
2
Plug the mains lead into an appropriate socket.
The main voltage is indicated on the rear of the television and the frequency is 50 or 60Hz.
Press the (Power) button (On/Off) on the front of the television or press the POWER button on
the remote control to switch the television on. The channel that you were watching last is re-selected
automatically. If you have not yet stored any channels, no clear picture appears. Refer to “Storing
Channels Automatically” on page 13 or “Storing Channels Manually” on page 14.
If the television is initially powered on, several basic customer settings proceed automatically.
Refer to “Plug & Play Feature” on pages 10~11.
To switch the television off, press the (Power) button (On/Off) on the front of the television or press
the POWER button on the remote control.
To switch the TV on, press the (Power) button (On/Off) on the front of the TV or press the POWER
button or number buttons on the remote control.
➢
➢
3
4
Viewing the Menus
1
2
3
4
5
Press the MENU button.
The main menu is displayed on the screen.
Its left side has five icons: Picture, Sound, Channel, Setup,
and Input.
Press the ▲ or ▼ button to select one of the icons.
Press the ENTER button to access the icon’s sub-menu.
Press the ▲ or ▼ button to move to items in the menu.
Press the ENTER button to enter items in the menu.
Press the ▲/▼/◄/► button to change the selected items.
Press the RETURN button to return to the previous menu.
Press the EXIT button to exit from the menu.
TV
Picture
Mode
:Standard 
Cell Light 7
Contrast95
Brightness 45
Sharpness 50
Colour
50
Tint
G 50
R 50
Detailed Settings

Picture Options

Reset
:OK

Move
Enter
Exit
English - 책1.indb 9
2008-03-17 오후 4:21:17
Plug & Play Feature
When the television is initially powered on, several basic
customer settings proceed automatically and subsequently.
The following settings are available.
1
2
3
If the television is in standby mode, press the POWER button
on the remote control. The message Start Plug & Play. is
displayed. Press the ENTER button. Language menu is
displayed.
Select the appropriate language by pressing the ▲ or ▼
button. Press the ENTER button. The message Select Home
Use nwhen installing this TV in your home. is displayed.
Press the ◄ or ► button to select Store Demo or Home Use,
then press the ENTER button. The message to check the
connected status of the antenna is displayed.
➢The default selection is Home Use.
recommend setting the TV to Home Use mode for
We
the best picture in your home environment.
Demo mode is only intended for use in retail
Store
environments.
unit is accidentally set to Store Demo mode and
Ifyouthewant
to return to Home Use (Standard): Press the
4
5
6
Volume button. When the volume OSD is displayed,
press and hold the MENU button for 5 seconds.
Make sure that the antenna is connected to the TV.
Press the ENTER button. Area menu is displayed.
Select your country or area by pressing the ▲ or ▼ button,
then press the ENTER button. Auto Store menu is displayed.
Press the ENTER button to start search the channels.
The channel search will start and end automatically. After
all the available channels are stored, Clock Set menu is
automatically displayed. Press the ENTER button.
To stop the search before it has finished, press the
ENTER button with Stop selected.
Press the ◄ or ► button to select Month, Day, Year, Hour,
Minute or am/pm. Set these by pressing the ▲ or ▼ button.
You can set the Month, Day, Year, Hour, and Minute
directly by pressing the numeric buttons on the remote
control.
Press the ENTER button to confirm your setting.
The message Enjoy your viewing is displayed.
When you have finished, press the ENTER button.
Even if the ENTER button is not pressed, the message will
automatically disappear after several seconds.
Plug & Play
Start Plug & Play.
OK
Plug & Play
English
Language
Français
Move
Plug & Play
Store Demo
Move
➢
Home Use
Enter
Plug & Play
Check antenna input.
OK
Enter
Skip
Plug & Play
Asia/W.Europe
CIS/E.Europe
China
Hong Kong/UK
Area
▼
Move
Enter
➢
8
Enter
Select Home Use
when installing this TV in your home.
➢
7
Enter
Skip
Plug & Play
P 1
C --
40 MHz
0 %
Start
Enter
Skip
Plug & Play
Clock Set
Month Day
▼
--
▼
--
Move
Year
----
Hour
Minute am/pm
-- --
Adjust am
Enter
Enjoy your viewing
OK
Continued...
English - 10
책1.indb 10
2008-03-17 오후 4:21:19
If you want to reset this feature …
1
2
3
TV
Setup
Plug & Play
Language
:English
Time Light Effect
:In Watching TV
Wall-mount Adjustment
Melody
:Off
Entertainment
:Off
Energy Saving
:Off
PIP
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Setup, then press the
ENTER button.
Press the ENTER button again to select Plug & Play.
The message Start Plug & Play. is displayed.
Move
Enter









Return
Using the TOOLS Button
You can use the TOOLS button to select your frequently used functions quickly and easily.
The “TOOLS” menu changes depending on which external input mode you are viewing.
1
2
3
Press the TOOLS button.
The TOOLS menu will appear.
Press the ▲ or ▼ button to select a menu, then press the
ENTER button.
Press the ▲/▼/◄/►/ENTER buttons to display, change, or
use the selected items.
For a more detailed description of each function, refer to the
corresponding page.
TOOLS
Anynet+ (HDMI-CEC)
Picture Mode
:
Sound Mode
:
Sleep Timer
:
SRS TS XT
:
Energy Saving
:
Dual I-II
:
Move
Enter
Standard
Custom
Off
Off
Off
Mono
Exit
• Anynet+(HDMI-CEC), see page 34
• Picture Mode, see page 17
• Sound Mode, see page 24
• Sleep Timer, see page 27
• SRS TS XT, see page 25
• Energy Saving, see page 28
• Dual I-II, see page 26
English - 11
책1.indb 11
2008-03-17 오후 4:21:20
Viewing External Signal Sources
You can switch between viewing signals from connected
equipment, such as a VCR, DVD, Set-Top Box, and the TV
source (broadcast or cable).
1
2
3
4
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Input, then press the
ENTER button.
Press the ENTER button again to select Source List.
Press the ▲ or ▼ button to select the signal source, then
press the ENTER button.
Available signal sources: TV, AV1, AV2, S-Video,
Component1, Component2, PC, HDMI1, HDMI2, HDMI3
You can choose only those external devices that are
connected to the TV.
TV
Input
Source List
:TV
Edit Name
Anynet+ (HDMI-CEC)
Move
TV


Enter
Return
Source List
TV
AV1
AV2
S-Video Component1
Component2
PC
HDMI1
HDMI2
HDMI3
➢
Move
:−−−−
:−−−−
:−−−−
:−−−−
:−−−−
:−−−−
:−−−−
:−−−−
:−−−−
Enter
Return
can select these options simply by pressing the SOURCE
➢You
button on the remote control.
watch television programme again, press the TV button and
➢To
select the channel number required.
can also watch HDMI mode simply by pressing the HDMI
➢You
button on the remote control.
English - 12
책1.indb 12
2008-03-17 오후 4:21:21
Editing Device Names
You can give a name to the external source.
1
2
3
4
5
6
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Input, then press the
ENTER button.
Press the ▲ or ▼ button to select Edit Name, then press the
ENTER button.
Press the ▲ or ▼ button to select the external source to be
edited, then press the ENTER button.
Select the required device by pressing ▲ or ▼, then press the
ENTER button.
Available device names: VCR, DVD, Cable STB, Satellite
STB, PVR STB, AV Receiver, Game, Camcorder, PC, TV,
IPTV, Blu-Ray, HD DVD, DMA
Press the EXIT button to exit.
Input
TV
Source List
:TV
Edit Name
Anynet+ (HDMI-CEC)
Move
Enter
TV



Return
Edit Name
AV1
AV2
S-Video
Component1
Component2
PC
HDMI1
HDMI2
HDMI3
:−−−− −−−−
:−−−− VCR
:−−−− DVD
:−−−−
Cable STB
:−−−−
Satellite STB
:−−−−
PVR STB
:−−−−
AV Receiver
:−−−− Game
:−−−− ▼
Move
Enter
Return
Storing Channels Automatically
You can scan for the frequency ranges available to you
(availability depends on your country).
Automatically allocated programme numbers may not
correspond to actual or desired programme numbers.
However you can sort numbers manually and clear any
channels you do not wish to watch.
1
2
3
4
5
6
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Channel, then press the
ENTER button.
Press the ENTER button to select Area.
Select your area by pressing the ▲ or ▼ button, then press the
ENTER button.
Press the ▲ or ▼ button to select Auto Store, then press the
ENTER button.
Press the ENTER button again to start the search.
The search will end automatically.
To stop the search before it has finished, press the
RETURN or the ENTER button.
➢
TV
Channel
Area
:Asia/W.Europe
Auto Store
Manual Store
Channel Manager
Sort
Name
Fine Tune
Move
Enter
TV







Return
Channel
Area
:Asia/W.Europe
Asia/W.Europe
Auto Store CIS/E.Europe
Manual Store
China
Channel Manager Hong Kong/UK
Sort Australia
Name NZL/Indonesia
Fine Tune South Africa
America
Move
Enter
Return
Auto Store
P 1
C --
40 MHz
0 %
Start
Enter
Return
English - 13
책1.indb 13
2008-03-17 오후 4:21:22
Storing Channels Manually
You can store television channels, including those received via
cable networks.
When storing channels manually, you can choose:
Whether or not to store each of the channels found.
The programme number of each stored channel which you wish
to identify.
1
2
3
4
5
6
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Channel, then press the
ENTER button.
Press the ▲ or ▼ button to select Manual Store, then press
the ENTER button.
Select the required option by pressing the ▲ or ▼ button, then
press the ENTER button.
When you are satisfied with your setting, press the ENTER
button.
Press the EXIT button to exit.
TV
Channel
Area
:Asia/W.Europe
Auto Store
Manual Store
Channel Manager
Sort
Name
Fine Tune
TV
Move
Enter







Return
Manual Store
Programme
Colour System
Sound System
Channel
Search
Store
:P 1
:Auto
:BG
:C
2
: 48
MHz
:?


Programme (Programme number to be assigned to a channel)
Move
Enter
Return
− Press the ▲ or ▼ button until you find the correct number.
You can also select the channel number directly by pressing the numeric buttons (0~9) on the
remote control.
Colour System: Auto/PAL/SECAM/NTSC 4.43/NTSC 3.58
− Press the ▲ or ▼ button to select the required colour standard.
Sound System: BG/DK/I/M
− Press the ▲ or ▼ button to select the required sound standard.
Channel (When you know the number of the channel to be stored)
− Press the ▲ or ▼ button to select C (Air channel) or S (Cable channel).
− Press the ► button, then press the ▲ or ▼ button to select the required number.
You can also select the channel number directly by pressing the numeric buttons (0~9) on the
remote control.
If there is abnormal sound or no sound, re-select the sound standard required.
Search (When you do not know the channel numbers)
− Press the ▲ or ▼ button to start the search.
− The tuner scans the frequency range until the first channel or the channel that you selected is
received on the screen.
Store (When you store the channel and associated programme number)
− Set to OK by pressing the ENTER button.
➢
➢
➢
mode
☛Channel
 P (Programme mode): When completing tuning, the broadcasting stations in your area have
been assigned to position numbers from P00 to P99. You can select a channel by entering the
position number in this mode.
 C (Air channel mode): You can select a channel by entering the assigned number to each air
broadcasting station in this mode.
 S (Cable channel mode): You can select a channel by entering the assigned number for each
cable channel in this mode.
English - 14
책1.indb 14
2008-03-17 오후 4:21:23
Adding / Locking Channels
Using the Channel Manager, you can conveniently add or lock
channels.
1
2
3
TV
Channel
Area
:Asia/W.Europe
Auto Store
Manual Store
Channel Manager
Sort
Name
Fine Tune
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Channel, then press the
ENTER button.
Press the ▲ or ▼ button to select Channel Manager, then
press the ENTER button.
Adding channels
Using the Channel List, you can add channels.
4 Press the ENTER button again to select Channel List.
5 Move to the ( ) field by pressing the ▲/▼/◄/► buttons,
select a channel to be added, and press the ENTER button to
add the channel.
If you press the ENTER button again, the ( ) symbol next
to the channel disappears and the channel is not added.
Move
TV
Enter







Return
Channel Manager
Channel List
Child Lock
:Off


➢
Locking channels
This feature allows you to prevent unauthorized users, such as
children, from watching unsuitable programmes by muting out
video and audio.
6 Press the ▲ or ▼ button to select Child Lock, then press the
ENTER button.
7 Select On by pressing the ▲ or ▼ buttons, then press the
ENTER button.
8 Press the ▲ or ▼ button to select Channel List, then press
the ENTER button.
9 Move to the ( ) field by pressing the ▲/▼/◄/► buttons,
select a channel to be locked, and press the ENTER button.
If you press the ENTER button again, the ( ) symbol
next to the channel disappears and the channel lock is
canceled.
A blue screen is displayed when Child Lock is activated.
10 Press the EXIT button to exit.
➢
Enter
Return
Channel List
P 1 C4
1/10
Prog.
0
1
2
3
4
5
6
7
8
9
TV
▲
C -C2
C 83
C 80
C7
C 89
C 90
C 11
C 12
C 13
Add
Move
Page
▼
Lock
Enter
Return
Channel Manager
Channel List
Child Lock
:Off
➢
can select these options simply by pressing the CH LIST
➢You
button on the remote control.
Move
Move
Enter
Off
On
Return
English - 15
책1.indb 15
2008-03-17 오후 4:21:25
Sorting the Stored Channels
1
2
3
4
5
6
Channel
Area
:Asia/W.Europe
Auto Store
Manual Store
Channel Manager
Sort
Name
Fine Tune
Move
Enter
TV







Return
Sort
Prog.
Ch.
0
C−−
C2
C83
C80
C7
C8
C9
C10
C11
C15
1
2
3
4
5
6
7
8
9
Move
Name

7
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Channel, then press the
ENTER button.
Press the ▲ or ▼ button to select Sort, then press the
ENTER button.
Select the channel that you wish to move by pressing the
▲ or ▼ button, then press the ENTER button.
Select the number of the programme to which the channel is to
be moved by pressing the ▲ or ▼ button.
Press the ENTER button. The channel is moved to its new
position and all other channels are shifted accordingly.
Repeat steps 4 to 5 until you have moved all the channels to
the required programme numbers.
Press the EXIT button to exit.
TV

This operation allows you to change the programme numbers
of the stored channels.
This operation may be necessary after using the auto store.
---------------------
---------------------
Enter

Return
Assigning Names to Channels
1
2
3
4
5
6
Channel
Area
:Asia/W.Europe
Auto Store
Manual Store
Channel Manager
Sort
Name
Fine Tune
Move
Enter
TV







Return
Name
Prog.
Ch.
0
C−−
C2
C83
C80
C7
A
C8
C9
C10
C11
C15
1
2
3
4
5
6
7
8
9

7
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Channel, then press the
ENTER button.
Press the ▲ or ▼ button to select Name, then press the
ENTER button.
Press the ▲ or ▼ button to select the channel to be assigned
to a new name, then press the ENTER button.
Press the ▲ or ▼ button to select a letter, a number, or a
symbol (Results in this sequence: A~Z, 0~9, +, -, *, /, blank).
Move on to the previous or next letter by pressing the ◄ or ►
button, then press the ENTER button.
Repeat steps 4 to 5 for each channel to be assigned to a new
name.
Press the EXIT button to exit.
TV

Channel names will be assigned automatically when channel
information is broadcast. These names can be changed,
allowing you to assign new names.
Move
Name
---------------------
---------------------
Adjust
Return
English - 16
책1.indb 16
2008-03-17 오후 4:21:26
Fine Tuning Channel Reception
If the reception is clear, you do not have to fine tune the
channel, as this is done automatically during the search and
store operation.
If the signal is weak or distorted, you may have to fine tune the
channel manually.
1
2
3
4
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Channel, then press the
ENTER button.
Press the ▲ or ▼ button to select Fine Tune, then press the
ENTER button.
To obtain a sharp, and clear picture and good sound quality,
press the ◄ or ► button until you reach the optimal setting.
Press the ENTER button.
Press the INFO button. Fine Tune Store will change the
colour of the Channel OSD (On Screen Display) from white
to red and add the “ * ” mark.
To reset the fine tuning to 0, select Reset by pressing the
▲ or ▼ button. Press the ENTER button.
Press the EXIT button to exit.
TV
Channel
Area
:Asia/W.Europe
Auto Store
Manual Store
Channel Manager
Sort
Name
Fine Tune
Move
Enter







Return
Fine Tune
P 1*
+2
➢
Reset
Adjust
Save
Return
➢
5
P 1*
Mono
Picture
Sound
SRS TS XT
−− : −− am
:Standard
:Custom
:Off
Changing the Picture Standard
You can select the type of picture which best corresponds to
your viewing requirements.
1
2
3
4
5
Press the MENU button to display the menu.
Press the ENTER button to select Picture.
Press the ENTER button again to select Mode.
Select the required mode by pressing the ▲ or ▼ button,
then press the ENTER button.
Available modes: Dynamic, Standard, Movie
The settings values may vary depending on the input
source.
Press the EXIT button to exit.
➢
TV
Picture
Mode
:Standard 
Cell Light 7
Contrast95
Brightness 45
Sharpness 50
Colour
50
Tint
G 50
R 50
Detailed Settings 
Picture Options 
Reset
:OK 
Enter
Return
Picture
Mode
:Standard
Dynamic
Cell Light Standard 7
Contrast95
Movie
Brightness 45
Sharpness 50
Colour
50
Tint
G 50
R 50
Detailed Settings
Picture Options
Reset
:OK
Dynamic for viewing the TV during the day or
➢  Choose
when there is bright light in the room.
 Choose Standard for general TV watching mode.
 Choose Movie when viewing the movie.
➢
Move
TV
Move
Enter
Return
You can select these options simply by pressing the P.MODE
button on the remote control.
Easy Setting
1
Press the TOOLS button on the remote control.
2
Press the ▲ or ▼ button to select Picture Mode.
3
Press the ◄ or ► button to select the required option.
TOOLS
Anynet+ (HDMI-CEC)
Picture Mode
◄
Sound Mode
:
Sleep Timer
:
SRS TS XT
:
Energy Saving
:
Dual I-II
:
Move
Adjust
Standard
Custom
Off
Off
Off
Mono
►
Exit
English - 17
책1.indb 17
2008-03-17 오후 4:21:27
Customizing the Picture Settings
Your television has several setting options that allow you to
control the picture quality.
1
2
3
4
5
6
7
Press the MENU button to display the menu.
Press the ENTER button to select Picture.
Press the ENTER button again to select Mode.
Select the required mode by pressing the ▲ or ▼ button,
then press the ENTER button.
Available modes: Dynamic, Standard, Movie
Select the required option by pressing the ▲ or ▼ button,
then press the ENTER button.
When you are satisfied with your setting, press the ENTER
button.
Press the EXIT button to exit.
TV
Picture
Mode
:Standard 
Cell Light 7
Contrast95
Brightness 45
Sharpness 50
Colour
50
Tint
G 50
R 50
Detailed Settings 
Picture Options 
Reset
:OK 
Move
Enter
Return
Cell Light7
Move
Adjust
Return
Cell Light - Contrast – Brightness – Sharpness – Colour – Tint
In TV, AV, S-Video modes of the PAL system, you cannot use the Tint Function.
In PC mode, you can only make changes to Cell Light, Contrast, and Brightness.
Press the ◄ or ► button until you reach the optimal setting.
➢
➢
Configuring Detailed Settings on the Picture
You can set detail picture settings.
1
2
3
4
5
6
➢
➢
TV
Press the MENU button to display the menu.
Press the ENTER button to select Picture.
Press the ▲ or ▼ button to select Detailed Settings, then
press the ENTER button.
Select the required option by pressing the ▲ or ▼ button, then
press the ENTER button.
Available options: Black Adjust, Dynamic Contrast,
Gamma, Colour Space, White Balance, Flesh Tone, Edge
Enhancement.
When you are satisfied with your setting, press the ENTER
button.
Press the EXIT button to exit.
When the picture mode is set to Movie or Standard, Detailed
Settings can be selected.
In PC mode, you can only make changes to Dynamic
Contrast, Gamma and White Balance from among the
Detailed Settings items.
Picture
Mode
:Standard 
Cell Light 7
Contrast95
Brightness 45
Sharpness 50
Colour
50
Tint
G 50
R 50
Detailed Settings 
Picture Options 
Reset
:OK 
TV
Move
Enter
Return
Detailed Settings
Black Adjust
:Off
Dynamic Contrast :Medium
Gamma
: 0
Colour Space
:Native
White Balance
Flesh Tone
: 0
Edge Enhancement:Off
Move
Enter







Return
Continued...
English - 18
책1.indb 18
2008-03-17 오후 4:21:29
Black Adjust: Off/Low/Medium/High
You can directly select the black level on the screen to adjust the screen depth.
Dynamic Contrast: Off/Low/Medium/High
You can adjust the screen contrast so that the optimal contrast is provided.
Gamma: -3 ~ +3
You can adjust the middle brightness of pictures.
Press the ◄ or ► button until you reach the optimal setting.
Colour Space: Auto/Native/Custom
Colour space is a colour matrix composed of red, green and blue colours.
Select your favorite colour space to experience the most natural colour.
− Auto: Auto Colour Space automatically adjusts to the most natural colour tone based on program
sources.
− Native: Native Colour Space offers deep and rich colour tone.
− Custom: Adjusts the colour range to suit your preference. (see “Customizing the Colour Space”)
Customizing the Colour Space
Colour: Red/Green/Blue/Yellow/Cyan/Magenta
Adjusts the Colour range to suit your preference.
Colour is available when Colour Space is set to Custom.
Press the ▲ or ▼ button to select Red, Green, Blue, Yellow, Cyan or Magenta.
Press the ENTER button.
− Red/Green/Blue: In Colour, you can adjust the RGB values for the selected colour.
Press the ▲ or ▼ button to select Red, Green or Blue to change it. Press the ENTER button.
Press the ◄ or ► button to decrease or increase the value of a particular item.
Press the ENTER button.
− Reset: Resets the colour space to the default values.
White Balance: R-Offset/G-Offset/B-Offset/R-Gain/G-Gain/B-Gain/Reset
You can adjust the colour temperature for more natural picture colours.
R-Offset/G-Offset/B-Offset/R-Gain/G-Gain/B-Gain: Changing the adjustment value will refresh the
adjusted screen.
Select the required option by pressing the ▲ or ▼ button, then press the ENTER button.
Press the ◄ or ► button until you reach the optimal setting.
Reset: The previously adjusted white balance will be reset to the factory defaults.
Flesh Tone:-15~+15
You can emphasize the pink tone in the picture.
Press the ◄ or ► button until you reach the optimal setting.
Changing the adjustment value will refresh the adjusted screen.
➢
Edge Enhancement: Off/On
You can emphasize object boundaries.
English - 19
책1.indb 19
2008-03-17 오후 4:21:29
Picture Options
You can set detailed picture settings.
1
2
3
4
5
6
➢
TV
Press the MENU button to display the menu.
Press the ENTER button to select Picture.
Press the ▲ or ▼ button to select Picture Options, then press
the ENTER button.
Select the required option by pressing the ▲ or ▼ button, then
press the ENTER button.
When you are satisfied with your setting, press the ENTER
button.
Press the EXIT button to exit.
In PC mode, you can only make changes to the Colour Tone,
Size and Screen Burn Protection from among the items in
Picture Options.
Colour Tone: Cool2/Cool1/Normal/Warm1/Warm2
When the picture mode is set to Dynamic or Standard,
Warm1 and Warm2 cannot be selected.
Picture
Mode
:Standard 
Cell Light 7
Contrast95
Brightness 45
Sharpness 50
Colour
50
Tint
G 50
R 50
Detailed Settings 
Picture Options 
Reset
:OK 
TV
Move
Enter
Return
Picture Options
Colour Tone
:Normal
Size
:16:9
Digital NR
:Auto
Real 100Hz Demo :Off
DNle
:Off
HDMI Black Level :Normal
Blue only mode :Off Screen Burn Protection
3D Effect
➢
Move
Enter









Return
Size: 16 : 9/Wide Zoom/Zoom/4 : 3/Just Scan
TV
Picture Options
You can select the picture size which best corresponds to
Colour Tone
:Normal

your viewing requirements.
Size
:16:9

− 16 : 9: Sets the picture to 16:9 wide mode.
Digital NR
:Auto

− Wide Zoom: Magnify the size of the picture more than 4:3.
Real 100Hz Demo :Off

DNle
:On

Move the screen up/down using the ▲ or ▼ button after
HDMI Black Level :Normal

selecting the by pressing the ► or ENTER button.
Blue only mode :Off 
− Zoom: Magnify the size of the picture vertically on screen.
Screen Burn Protection

3D Effect

− 4 : 3: Sets the picture to 4:3 normal mode.
− Just Scan: Use the function to see the full image without
Move
Enter
Return
any cutoff when HDMI (720p/1080i), Component (1080i)
signals are input.
TV
Size
After selecting “Just Scan” in HDMI (1080i) or
16 : 9
Wide
Zoom
Component (1080i) mode:
Zoom
Select by pressing the ◄ or ►button. Use the ▲, ▼, ◄
4:3
Just Scan
or ► button to move the picture.
Reset: Press the ◄ or ► button to select “Reset”, then
press the ENTER button. You can initialize the setting.
With the HDMI Just Scan picture size, depending on
the AV devices, the screen may be cut off or a specific
Move
Enter
Return
appears on the screen.
For an HDMI (1080p) connection of 24, 25, 30, 50,
and 60 Hz, and for a Component (1080p) connection of
50 and 60Hz, only the input source is supported.
You can change the picture size simply by pressing the
P.SIZE button on the remote control.
Depending on the input source, the picture size options
may vary.
The items available may differ depending on the selected mode.
Settings can be adjusted and stored for each external device you have connected to an input of
the TV.
In PC Mode, only “16:9” and “4:3” mode can be adjusted.
➢
➢
➢
➢
➢
➢
➢
Positioning and Sizing the screen using Zoom
− Resizing the screen using the Zoom enables the positioning and sizing of the screen to up/down
direction using the ▲ or ▼ button as well as the screen size.
− Move the screen up/down using the ▲ or ▼ button after selecting the by pressing the ◄ or ►
button.
− Resize the screen vertically using the ▲ or ▼ button after selecting the by pressing the ◄ or ►
button.
Continued...
English - 20
책1.indb 20
2008-03-17 오후 4:21:30
Digital NR: Off/Low/Medium/High/Auto
If the signal received by the television is weak, you can activate this feature to reduce any static and
ghosting that may appear on the screen.
This function is not available in PC mode.
➢
Real 100Hz Demo : Off/On
You can get a clear distinction between "Real 100Hz" and 50Hz, especially when watching sports.
Therefore, when seeing a paused or static image, you will not be able to distinguish between "Real
100Hz" and 50Hz.
DNIe: Off/Demo/On
This TV includes the DNIe function so as to provide a high visual quality. If you set DNIe to on, you
can view the screen with the DNIe feature activated. If you set the DNIe to Demo, you can view the
applied DNIe and normal pictures on the screen, for demonstration purposes. Using this function, you
can view the difference in the visual quality.
DNIeTM (Digital Natural Image engine)
This feature brings you more detailed image with 3D noise reduction, detail enhancement,
contrast enhancement and white enhancement. New image compensation Algorithm gives
brighter, clearer, more detailed image to you. DNIeTM technology will fit every signal into your
eyes.
This function is not available in PC mode.
DNIe is only available in Dynamic mode.
➢
➢
➢
HDMI Black Level: Normal/Low
Using this function, you can adjust the image quality when the screen burn (appearance of black
level, low contrast, low colour, etc.) is encountered by the HDMI input for RGB limited range (16 to
235).
This function is active only when the external input connects to HDMI(RGB signals).
➢
Blue Only Mode: Off/On
This function is for AV device measurement experts. This function displays the blue signal only by
removing the red and green signals from the video signal so as to provide a Blue Filter effect that
is used to adjust the Color and Tint of video equipment such as DVD players, Home Theaters, etc.
Using this function, you can adjust the Color and Tint to preferred values appropriate to the signal
level of each video device using the Red/Green/Blue/Cyan/Magenta/Yellow Color Bar Patterns,
without using an additional Blue Filter.
Blue Only Mode is available when the picture mode is set to Movie or Standard.
➢
Screen Burn Protection: Pixel Shift/White/Scrolling/Side Gray
To reduce the possibility of screen burn, this unit is equipped with screen burn prevention technology.
This technology enables you to set picture movement up/down (Vertical Line) and side to side
(Horizontal Dot). The Time setting allows you to program the time between movement of the picture
in minutes.
− Pixel Shift: Using this function, you can minutely move
TV
Screen Burn Protection
pixels on the PDP in horizontal or vertical direction to
Pixel Shift

minimize after image on the screen.
White 
Scrolling 
− Set Pixel Shift to On by pressing the ▲ or ▼ button,
Side Gray
:Dark

then press the ENTER button.
− Select the required option by pressing the ▲ or ▼
button, then press the ENTER button.
Available options: Horizontal Dot, Vertical Line,
Time
Move
Enter
Return
Optimum condition for pixel shift;
➢
PC
TV/AV/S-Video/
Component/HDMI
Horizontal Dot
1
2
Vertical Line
1
2
Time (minute)
2
2 min
➢
➢
The Pixel Shift value may differ depending on the
monitor size (inches) and mode.
This function is not available in the Just Scan mode.
English - 21
책1.indb 21
TV
Pixel Shift
Pixel Shift
Horizontal Dot
Vertical Line
Time
Move
:On
:2
:2
:2 min
Enter




Return
Continued...
2008-03-17 오후 4:21:31
−
−
−
➢
➢
➢
White: This function helps remove after images on the screen by changing the colour of pixels
to white. Use this function when there are remaining after images or symbols on the screen
especially when you displayed a still image on the screen for a long time.
Scrolling: This function helps remove after images on the screen by moving all the pixels on the
PDP according to a pattern. Use this function when there are remaining after images or symbols
on the screen especially when you displayed a still image on the screen for a long time.
Side Gray: When you watch TV with the screen ratio of 4:3, the screen is prevented from any
damage by adjusting the white balance on both extreme left and right sides.
Dark: When you set the screen ratio to 4:3, it darkens the left and right sides.
Light: When you set the screen ratio to 4:3, it brightens the left and right sides.
To remove after images on the screen, use either White or Scrolling function.
Although both of the two functions remove after images on the screen, Scrolling is more
effective.
The after image removal function has to be executed for a long time (approximately 1 hour) to
effectively remove after images on the screen. If after image is not improved after the execution
of the function, repeat the function again.
Press any button on the remote control to cancel this feature.
D Effect: Mode/Format
You can enjoy 3D movies and games on your TV. The 3D effects function enables you to view 3D
images using special 3D glasses.
Connections
D Glasses
(Not supplied)
TV Rear Panel
D IR Emitter
(Not supplied)
PC
.5 mm Stereo plug to RCA Cable (Not supplied)
HDMI/DVI Cable (Not supplied)
➢ The appearance of the 3D glasses (including Emitter) may differ depending on the model of your glasses.
1
4
Connect a HDMI/DVI cable between the HDMI IN 2 jack on the TV and the PC output jack on your
computer.
Connect a 3.5mm Stereo/2RCA cable between the DVI IN (HDMI 2) [R-AUDIO-L] jack on the TV and
the Audio Out jack of the sound card on your computer.
Connect the Emitter to the 3D SYNC OUT port on the rear panel of the TV.
Turn the TV on and set the source of the TV to HDMI2.
Continued...
English - 책1.indb 22
2008-03-17 오후 4:21:33
 For more information on the 3D glasses (including the Emitter), refer to the user manual of your 3D glasses.
 Adjust the PC resolution










- PS42A450 : 1024 x 768@60Hz
- PS50A450 : 1024 x 768@60Hz
1360 x 768@60Hz
The 3D IR Emitter communicates with the 3D glasses.
Therefore, the 3D IR Emitter should be located near the 3D glasses.
It is activated when the HDMI or DVI input signal is RGB, and DVI Sound is supported.
When the power is turned on or off, the mode changes to the default (Off) and the Format is saved.
The 3D Effect is turned on or off regardless of the Picture Mode.
When 3D Effect is on, only the Contrast, Brightness, 3D Effect, and Reset picture menus are
activated.
To use the 3D Effect function, a graphics card supporting 3D or 3D software is required.
The 3D glasses and the Emitter must be manufacturer by the same company.
If you play a game or watch TV while wearing the 3D glasses for long periods of time, you may
experience eyestrain or a headache.
3D glasses (including the Emitter) not manufactured by Samsung may not be supported.
If you find the screen flickering while the 3D function is used, change the environmental lighting
darker or turn off the fluorescent lamp to watch the screen for its best condition.
Changing the Mode
Provides the function to turn on the 3D Effect. You can choose
between Mode1 and Mode2. To achieve the 3D Effect, the 3D
glasses shutter back and forth from the left to right and vice versa
(left/right sync).
1 Connect the TV, PC and 3D IR Emitter as shown in the figure.
2 Press the SOURCE button to select HDMI2 .
3 Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Picture, then press the
ENTER button.
4 Press the ▲ or ▼ button to select Picture Options then press
the ENTER button.
Press the ▲ or ▼ button to select 3D Effect then press the
ENTER button.
5 Press the ▲ or ▼ button to select Mode, then press the
ENTER button.
Press the ▲ or ▼ button to select Off, Mode1 or Mode2 then
press the ENTER button.
• Off : Turns the 3D Effect function off.
• Mode1 : Mode 1 operates with right sync first.
• Mode2 : Mode 2 operates with left sync first.
TV
Picture
Mode
:Standard 
Cell Light 7
Contrast95
Brightness 45
Sharpness 50
Colour
50
Tint
G 50
R 50
Detailed Settings 
Picture Options 
Reset
:OK 
TV
Checker Board
If the output format of your graphic card or 3D software
is Checkerboard, select this input format.
Horizontal
If the output format of your graphic card or 3D software
is Horizontal interleaved, select this input format.
Vertical
If the output format of your graphic card or 3D software
is Vertical interleaved, select this input format.
Enter
Return
Picture Options
Colour Tone
:Normal
Size
:16:9
Digital NR
:Auto
Real 100Hz Demo :Off
DNle
:On
HDMI Black Level :Normal
Blue only mode :Off Screen Burn Protection
3D Effect
Move
TV
Enter









Return
3D Effect
Mode
Format
 If the 3D effect is not working properly, it means the Mode and
3D glasses may not be syncing properly. To put them in sync,
switch to the other mode.
Changing the Format
Select the optimal input format to match your graphic cards or 3D
software.
See the descriptions for Steps 1 to 4 above.
5 Press the ▲ or ▼ button to select Format, then press the
ENTER button.
6 Press the ▲ or ▼ button to select Checker Board, Horizontal
or Vertical then press the ENTER button.
Move
Move
TV
:Mode Off
1
ModeBoard
1
:Checker
Mode 2
Enter
Return
3D Effect
Mode
Format
Move
:Mode 1
:Checker
Board
Checker Board
Horizontal
Vertical
Enter
Return
English - 23
책1.indb 23
2008-03-17 오후 4:21:35
Resetting the Picture Settings to the Factory Defaults
You can set detailed picture settings.
1
2
3
4
TV
Press the MENU button to display the menu.
Press the ENTER button to select Picture.
Press the ▲ or ▼ button to select Reset, then press the
ENTER button.
Press the ▲ or ▼ button to select OK or Cancel then press
the ENTER button.
Picture
Mode
:Standard
Cell Light 7
Contrast95
Brightness 45
Sharpness 50
Colour
50
Tint
G 50
R 50
Detailed Settings
Picture Options
Reset
:OK OK
Cancel
Move
Enter
Return
➢Each mode can be reset.
Sound Features
1
2
3
4
5
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Sound, then press the
ENTER button.
Select the required option by pressing the ▲ or ▼ button, then
press the ENTER button.
Available options: Mode, Equalizer, SRS TS XT, Auto Volume,
TV Speaker, Sound Select
When you are satisfied with your setting, press the ENTER
button.
Press the EXIT button to exit.
Mode: Standard/Music/Movie/Speech/Custom
You can select the type of special sound effect to be used
when watching a given broadcast.
 Choose Standard for the TV standard factory
settings.
 Choose Music when watching the music videos or
concerts.
 Choose Movie when watching movies.
 Choose Speech when watching a show that is
mostly dialog(i.e., news).
 Choose Custom to recall your personalized settings.
Easy Setting
1 Press the TOOLS button on the remote control.
2 Press the ▲ or ▼ button to select Sound Mode.
3 Press the ◄ or ► button to select the required option.
➢ TV
Sound
Mode
:Custom
Equalizer
SRS TS XT
:Off
Auto Volume
:Off
TV Speaker:
:On
Sound Select
:Main
Move
Enter
TV






Return
Equalizer
R
L
Balance
Move
+
+
0
0
-
-
100Hz 300Hz 1kHz 3kHz 10kHz
Adjust
TOOLS
Anynet+ (HDMI-CEC)
Picture Mode
:
Sound Mode
◄
Sleep Timer
:
SRS TS XT
:
Energy Saving
:
Dual I-II
:
Return
Standard
Custom
Off
Off
Off
Mono
►
Equalizer: Balance/100Hz/300Hz/1kHz/3kHz/10kHz
The television has several settings which allow you to control
the sound quality.
Move
Adjust
Exit
 R/L Sound Balance Adjustment:
To adjust the sound balance of the R/L speakers.
 Bandwidth Adjustment(100Hz, 300Hz, 1kHz, 3kHz, 10kHz) : To adjust the level of different
bandwidth frequencies.
If you make any changes to these settings, the sound standard is automatically switched to
Custom.
➢ ➢
Continued...
English - 24
책1.indb 24
2008-03-17 오후 4:21:36
SRS TS XT: Off/On
TruSurround XT is a patented SRS technology that solves the problem of playing 5.1 multichannel
content over two speakers. TruSurround delivers a compelling, virtual surround sound experience
through any two-speaker playback system, including internal television speakers. It is fully compatible
with all multichannel formats.
TruSurround XT, SRS and
Symbol are trademarks of SRS Labs, Inc.
TruSurround XT technology is incorporated under license from SRS Labs, Inc.
can select these options simply by pressing the SRS
➢You
button on the remote control.
Easy Setting
1 Press the TOOLS button on the remote control.
2 Press the ▲ or ▼ button to select SRS TS XT.
3 Press the ◄ or ► button to select Off or On.
TOOLS
Anynet+ (HDMI-CEC)
Picture Mode
:
Sound Mode
:
Sleep Timer
:
SRS TS XT
◄
Energy Saving
:
Dual I-II
:
Move
Adjust
Standard
Custom
Off
Off
Off
Mono
►
Auto Volume: Off/On
Each broadcasting station has its own signal conditions, and
so it is not easy to adjust the volume every time the channel is
Exit
changed. This feature lets you automatically adjust the volume
of the desired channel by lowering the sound output when the modulation signal is high or by raising
the sound output when the modulation signal is low.
TV Speaker: Off/On
If you want to hear the sound through separate speakers, cancel the internal amplifier.
The , and MUTE buttons do not operate when the TV Speaker is set to Off.
When TV Speaker is set to Off, you can operate only Sound Select (in PIP mode) in Sound
menu.
➢
➢
Sound Select: Main/Sub
When the PIP feature is activated, you can listen to the sound of the sub (PIP) picture.
− Main: Used to listen to the sound of the main picture.
− Sub: Used to listen to the sound of the sub picture.
English - 25
책1.indb 25
2008-03-17 오후 4:21:37
Selecting the Sound Mode (depending on the model)
The DUAL I-II button displays/controls the processing and output of the audio signal. When power
is switched on, the mode is automatically preset to either “DUAL-I” or “Stereo”, depending on the
current transmission.
TOOLS
Anynet+ (HDMI-CEC)
Picture Mode
:
Sound Mode
:
Sleep Timer
:
SRS TS XT
:
Energy Saving
:
Dual I-II
◄
Easy Setting
1 Press the TOOLS button on the remote control.
2 Press the ▲ or ▼ button to select Dual I-II.
3 Press the ◄ or ► button to select the required option.
Move
Type of broadcast
Regular broadcast
(Standard audio)
NICAM
Stereo
A2
Stereo
►
Exit
Adjust
On-screen indication
Mono (Normal use)
Regular + NICAM Mono
NICAM
Mono
(Normal)
NICAM Stereo
NICAM
Stereo
Mono
(Normal)
NICAM DUAL-I/II
Standard
Custom
Off
Off
Off
Mono
NICAM
DUAL-1
Regular broadcast
(Standard audio)
Bilingual or DUAL-I/II
DUAL I
Stereo
Stereo
NICAM
DUAL-2
Mono
(Normal)
Mono (Normal use)
DUAL II
Mono
(Forced mono)
➢  If the receiving conditions deteriorate, listening will be easier if the mode is set to Mono.
 If the stereo signal is weak and automatic switching occurs, switch to Mono.
Connecting Headphones (Sold separately)
You can connect a set of headphones to your set if you wish to watch a TV program without
disturbing other people in the room.
➢ When you insert the head set jack into the corresponding
TV Side Panel
port, you can operate only “Auto Volume” in Sound menu.
➢Prolonged use of headphones at a high volume may
damage your hearing.
➢You will not hear sound from the speakers when you
connect headphones to the TV.
➢The headphone volume and TV volume are adjusted
separately.
English - 26
책1.indb 26
2008-03-17 오후 4:21:37
Time Features
1
2
3
4
5
6
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Setup, then press the
ENTER button.
Press the ▲ or ▼ button to select Time, then press the
ENTER button.
Select the required option by pressing the ▲ or ▼ button,
then press the ENTER button.
Available options: Clock Set, Sleep Timer, Timer1, Timer2,
Timer3
When you are satisfied with your setting, press the
ENTER button.
Press the EXIT button to exit.
TV
Setup
Plug & Play
Language
:English
Time Light Effect
:In Watching TV
Wall-mount Adjustment
Melody
:Off
Entertainment
:Off
Energy Saving
:Off
PIP
TV
Move
Enter









Return
Time
Clock Set
Sleep Timer
Timer1
Timer2
Timer3
:−− : −− am
:Off
:Off
:Off
:Off





Clock Set
You can set the television clock so that the current time is
displayed when pressing the INFO button on the remote
control. You must also set the time if you wish to use the
automatic on or off timers.
Move
Enter
Return
− Press the ◄ or ► button to select Month, Day, Year, Hour,
Minute, or am/pm.
Set these by pressing the ▲ or ▼ button.
You can set the Month, Day, Year, Hour, and Minute
directly by pressing the numeric buttons on the remote
control.
In the event of a power interruption or the set being turned
off at the supply, the settings for the Clock will be lost.
Sleep Timer
You can select a time period of between 30 and 180 minutes after which the television automatically
switches to standby mode.
− Select the preset time interval (Off, 30, 60, 90, 120, 150, 180) for staying on by pressing the ▲ or
▼ button.
TOOLS
Easy Setting
Anynet+ (HDMI-CEC)
1 Press the TOOLS button on the remote control.
Picture Mode
: Standard
2Press the ▲ or ▼ button to select Sleep Timer.
Sound Mode
: Custom
Sleep
Timer
◄
Off
►
3Press the ◄ or ► button to select the minute, then press SRS TS XT
: Off
the ENTER button.
Energy Saving
: Off
Dual I-II
: Mono
Timer1 / Timer2 / Timer3
Move
Exit
Adjust
You can set the On/Off timers so that the television will switch
on or off automatically at the time you select.
TV
Timer 1
You must set the clock first.
On Time
− Press the ◄ or ► button to select the required item below.
:
12
00
am
Off
Press the ▲ or ▼ button to adjust to the setting satisfied.
Off Time
:
12
00
am
Off
On Timer : Select hour, minute, am/pm, and Off/On.
Repeat
(To activate timer with the setting satisfied, set to On.)
Once
Off Timer : Select hour, minute, am/pm, and Off/On.
Volume
Programme
(To activate timer with the setting satisfied, set to On.)
10
01
Repeat : Select Once, Everyday, Mon ~ Fri, Mon ~ Sat, or
Move
Adjust
Return
Sat ~ Sun.
Volume : Select the required volume level.
Programme : Select the required channel.
➢
➢
☛
➢You can set the hour, and minute directly by pressing the number buttons on the remote control.
Power Off
☛Auto
When you set the timer “On”, the TV will eventually turn off, if no controls are operated for 3 hours
after the TV was turned on by timer. This function is only available in timer “On” mode and prevents
overheating, which may occur if a TV is on for too long time.
English - 27
책1.indb 27
2008-03-17 오후 4:21:38
Language / Light Effect / Melody / Entertainment /
Energy Saving
1
2
3
4
5
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Setup, then press the
ENTER button.
Select the required option by pressing the ▲ or ▼ button, then
press the ENTER button.
When you are satisfied with your setting, press the ENTER
button.
Press the EXIT button to exit.
TV
Setup
Plug & Play
Language
:English
Time Light Effect
:In Watching TV
Wall-mount Adjustment
Melody
:Off
Entertainment
:Off
Energy Saving
:Off
PIP









Move
Enter
Return
Language
It is variable depending on the model. When you start using
the television for the first time, you must select the language which will be used for displaying menus
and indications.
Light Effect: Off/ In Standby/In Watching TV/Always
You can turn on/off the blue LED on the front of TV according to the situation. Use it for saving power
or when the LED dazzles your eyes.
- Off: The blue LED is always off.
- In Standby: The blue LED lights while in Standby mode and it turns off when your TV is turned on.
- In Watching TV: The blue LED lights when watching TV and it turns off when your TV is turned off.
- Always: The blue LED always lights.
➢Set the Light Effect to Off to reduce the power consumption.
Melody: Off/Low/Medium/High
The TV power on/off melody sound can be adjusted.
When the Melody does not play
When no sound is output from the TV because the MUTE button has been pressed.
When no sound is output from the TV because the
(Volume) button has been pressed.
When the TV is turned off by Sleep Timer function.
➢
➢
➢
➢
Entertainment: Off/Sports/Cinema/Game
Entertainment mode enables you to select the optimal display and sound for sports, cinema and
games.
− Off: Switches the Entertainment function off.
− Sports: Provides the optimal picture and sound quality for sports.
− Cinema: Provides the optimal picture and sound quality for movie watching.
You can experience a richer picture and enhanced sound.
− Game: Provides the optimal picture and sound quality for games. This mode accelerates the
playing speed when using an external game console connected to the TV.
If you set any of the three Entertainment modes to On, the settings will be locked and can not
be adjusted. If you want to make Picture and Sound mode adjustments, the Entertainment mode
must be turned off.
The Entertainment settings are saved for each input source.
➢
➢
Energy Saving: Off/Low/Medium/High
This feature adjusts the screen brightness depending on the surrounding lighting conditions.
- Off: Switches off the Energy Saving mode.
- Low: Operates in standard mode regardless of the surrounding illumination.
- Medium: Enters medium power saving mode regardless of the surrounding illumination.
- High: Enters maximum power saving mode regardless of the surrounding illumination.
Easy Setting
1 Press the TOOLS button on the remote control.
2 Press the ▲ or ▼ button to select Energy Saving.
3 Press the ◄ or ► button to select the required option.
TOOLS
Anynet+ (HDMI-CEC)
Picture Mode
:
Sound Mode
:
Sleep Timer
:
SRS TS XT
:
Energy Saving
◄
Dual I-II
:
Move
Adjust
Standard
Custom
Off
Off
Off
Mono
►
Exit
English - 28
책1.indb 28
2008-03-17 오후 4:21:39
Viewing the Picture in Picture (PIP)
You can display a sub picture within the main picture. In this
way you can watch TV program or monitor the video input
from any connected devices.
1
2
3
4
5
6
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Setup, then press the
ENTER button.
Press the ▲ or ▼ button to select PIP, then press the
ENTER button.
Select the required option by pressing the ▲ or ▼ button, then
press the ENTER button.
Available options: PIP(Off/On), Source, Size, Position,
Programme
When you are satisfied with your setting, press the ENTER
button.
Press the EXIT button to exit.
PIP: Off/On
You can activate or deactivate the PIP function.
Main picture
Component1, 2
HDMI1, 2, 3
PC
TV
Setup
Plug & Play
Language
:English
Time Light Effect
:In Watching TV
Wall-mount Adjustment
Melody
:Off
Entertainment
:Off
Energy Saving
:Off
PIP
Move
TV
Enter









Return
PIP
PIP
Source
Size
Position
Programme
Move
:On
:TV
:
:
:P 1
Enter





Return
Sub picture
TV, AV1, AV2
Source: TV/AV1/AV2
You can select a source of the sub-picture.
You can select these options simply by pressing the SOURCE button on the remote control.
Size:
/
/
You can select a size of the sub-picture.
If main picture is in PC and Component mode, Size is not available.
Position:
/
/
/
You can select a position of the sub-picture.
Programme
You can select a channel of the sub-picture only when the Source is set to TV.
➢
➢
English - 29
책1.indb 29
2008-03-17 오후 4:21:40
Setting up Your PC Software (Based on Windows XP)
The Windows display-settings for a typical computer are shown below. But the actual screens
on your PC will probably be different, depending upon your particular version of Windows and
your particular video card. But even if your actual screens look different, the same, basic set-up
information will apply in almost all cases. (If not, contact your computer manufacturer or Samsung
Dealer.)
1
2
3
4
5
Right click the mouse on the Windows Desktop, then click on
Properties.
The Display Properties will be displayed.
Click on Settings tab, then set the Display Mode with
reference to the Display Modes Table. You do not need to
change the Colours settings.
Click on Advanced. A new settings dialog box will be
displayed.
Click on the Monitor tab, then set the Screen refresh rate
with reference to the Display Modes Table. Set the Vertical
Frequency and Horizontal Frequency individually if you can do
so instead of setting the Screen refresh rate.
Click on OK to close the window, then Click on OK button to
the Display Properties window. Automatic re-booting may commence at this moment.
English - 30
책1.indb 30
2008-03-17 오후 4:21:40
Input Mode (PC)
Both screen position and size will vary depending on the type of PC monitor and its resolution.
The table below shows all of the display modes that are supported:
D-Sub Input
Mode
Resolution
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
Pixel Clock
Frequency
(MHz)
Sync
Polarity
(H/V)
PS42A450
PS50A450
IBM
640 x 350
720 x 400
31.469
31.469
70.086
70.087
25.175
28.322
+/-/+
✔
✔
✔
✔
VESA
640 x 480
640 x 480
640 x 480
800 x 600
800 x 600
800 x 600
1024 x 768
1024 x 768
1024 x 768
1360 x 768
31.469
37.861
37.500
37.879
48.077
46.875
48.363
56.476
60.023
47.712
59.940
72.809
75.000
60.317
72.188
75.000
60.004
70.069
75.029
60.015
25.175
31.500
31.500
40.000
50.000
49.500
65.000
75.000
78.750
85.500
-/-/-/+/+
+/+
+/+
-/-/+/+
+/+
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
PS42A450
PS50A450
✔
✔
✔
✔
✔
✔
✔
HDMI/DVI Input
Mode
Resolution
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
Pixel Clock
Frequency
(MHz)
Sync
Polarity
(H/V)
VESA
640 x 480
800 x 600
1024 x 768
1360 x 768
31.469
37.879
48.363
47.712
59.940
60.317
60.004
60.015
25.175
40.000
65.000
85.500
-/+/+
-/+/+
When using an HDMI/DVI cable connection, you must use the HDMI IN 2 jack.
The interlace mode is not supported.
The set might operate abnormally if a non-standard video format is selected.
Separate and Composite modes are supported. SOG is not supported.
For the PS42A450, PC text quality is optimum in VESA mode (1024 x 768@60Hz).
For the PS50A450, PC text quality is optimum in VESA mode (1360 x 768@60Hz).
English - 31
책1.indb 31
2008-03-17 오후 4:21:40
Setting the PC
➢ Preset to the PC mode by pressing the SOURCE button.
1
2
3
4
5
TV
Press the MENU button to display the menu.
Press the ENTER button to select Picture.
Select the required option by pressing the ▲ or ▼ button, then
press the ENTER button.
Available options: Auto Adjustment, Screen Adjustment,
Reset
When you are satisfied with your setting, press the ENTER
button.
Press the EXIT button to exit.
Auto Adjustment
Auto adjustment allows the PC screen to self-adjust to the
incoming PC video signal.
The values of fine, coarse and position are adjusted
automatically.
Easy Setting
1 Press the TOOLS button on the remote control.
2 Press the ▲ or ▼ button to select Auto Adjustment, then
press the ENTER button.
Screen Adjustment: Coarse/Fine/Position/Image Reset
− Coarse/Fine
The purpose of picture quality adjustment is to remove or
reduce picture noise.
If the noise is not removed by Fine-tuning alone, then adjust
the frequency as best as possible (coarse) and Fine-tune
again.
After the noise has been reduced, re-adjust the picture so
that it is aligned on the center of screen.
1 Press the ▲ or ▼ button to select Coarse or Fine, then
press the ENTER button.
2 Press the ◄ or ► button to adjust the screen quality,
vertical stripes may appear or the picture may be blurry.
Press the ENTER button.
− Position
Adjust the PC’s screen positioning if it does not fit the TV
screen.
1 Adjust the position by pressing the ▲/▼/◄/► button.
2 Press the ENTER button.
− Image Reset
You can replace all image settings with the factory default
values.
Picture
Mode
:Standard

Cell Light 7
Contrast95
Brightness45
Sharpness 50
Auto Adjustment

Screen Adjustment

Detailed Settings


Picture Options
Reset
: OK

Move
Enter
Return
Auto Adjustment in Progress
Please wait.
TOOLS
Anynet+ (HDMI-CEC)
Picture Mode
:
Sound Mode
:
Sleep Timer
:
SRS TS XT
:
Energy Saving
:
PIP
Auto Adjustment
Standard
Custom
Off
Off
Off
Enter
Move
TV
Exit
Screen Adjustment
Coarse
50
Fine63
Position

Image Reset

Move
TV
Enter
Return
Position
Move
Enter
Return
Image Reset is completed.
English - 32
책1.indb 32
2008-03-17 오후 4:21:41
What is Anynet+?
Anynet+ is an AV network system that enables an easy-to-use AV interface for users by controlling
all connected AV devices through the Anynet+ menu when Samsung Electronics AV devices are
connected.
Connecting Anynet+ Devices
The Anynet+ system supports AV devices supporting Anynet+ only.
Check if there is an Anynet+ mark on the AV device to be connected to the TV.
To directly connect to TV
TV
Anynet+ Device 1 Anynet+ Device 2 Anynet+ Device 3
HDMI Cable
HDMI Cable
Connect the [HDMI IN 1],
[HDMI IN 2] or [HDMI IN 3]
jack on the TV and the HDMI
OUT jack of the corresponding
Anynet+ device using the HDMI
cable.
HDMI Cable
To connect to Home Theater
TV
Anynet+ Device 1
HDMI Cable
Anynet+ Device 2
HDMI Cable
Anynet+ Device 3
Home Theater
HDMI Cable
1Connect the [HDMI IN 1],
[HDMI IN 2] or [HDMI IN 3]
jack on the TV and the
HDMI OUT jack of the
corresponding Anynet+
device using the HDMI cable.
2Connect the HDMI IN jack
of the home theater and
the HDMI OUT jack of the
corresponding Anynet+
device using the HDMI
cable.
HDMI Cable
➢Connect only one receiver.
can connect an Anynet+ device using the HDMI Cable. Some HDMI cables may not support
➢You
Anynet+ functions.
➢Anynet+ works when the AV device supporting Anynet+ is in the Standby or On status.
➢Anynet+ supports up to 8 AV devices in total.
English - 33
책1.indb 33
2008-03-17 오후 4:21:43
Setting Up Anynet+
The following settings are to use Anynet+ functions.
1
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Input, then press the
ENTER button.
2 Press the ▲ or ▼ button to select Anynet+ (HDMI-CEC),
then press the ENTER button.
3 Press the ▲ or ▼ button to select Setup, then press the
ENTER button.
4 Press the ▲ or ▼ button to select Anynet+ (HDMI-CEC),
then press the ENTER button.
5 Press the ▲ or ▼ button to select On, then press the
ENTER button.
The Anynet+ (HDMI-CEC) function is enabled.
If you select Off, Anynet+ (HDMI-CEC) is disabled.
Turning an Anynet+ Device Off Automatically when the TV is
Turned Off
➢
➢
5
P 1
View TV
Using the Anynet+ Function
4
TV
Select Device

Record

Menu on Device

Device Operation

Receiver

:Off
Setup
Move
Return

Enter
Setup
Anynet+ (HDMI-CEC)
: Off
Auto Turn Off : Off
Off
On
Searching Connections
Move
Enter
Return
Press the ▲ or ▼ button to select Auto Turn Off, then press
Setup
the ENTER button.
Anynet+
(HDMI-CEC)
: On
Press the ▲ or ▼ button to select Yes, then press the
ENTER button.
Auto Turn Off : Off
No
The Auto turn off function is enabled.
Searching Connections
If you select No, the Auto turn off function is canceled.
Yes
Press the EXIT button to exit.
Move
Enter
Return
The Select Device setting of the TV remote control is to be set
to TV to use the Anynet+ function.
If you set Auto Turn Off to Yes, connected external devices are also turned off when the TV is turned
off. However, if the device is recording, it may not be turned off.
When the Anynet+ (HDMI-CEC) function is disabled, all the Anynet+ related operations are deactivated.
➢
➢
➢
➢
➢
Scanning and Switching between Anynet+ Devices
1
2
3
4
5
➢
➢
➢
➢
➢
Press the MENU button to display the menu.
TV
P 1
Press the ▲ or ▼ button to select Input, then press the
View TV
ENTER button.
DVDR1
Select Device

DVDR2
Press the ▲ or ▼ button to select Anynet+ (HDMI-CEC),
DVD1
Record

then press the ENTER button.
DVD2
Menu on Device

Press the ▲ or ▼ button to select Select Device, then press
Device Operation

the ENTER button.
Receiver :Off

Press the ▲ or ▼ button to select to a particular device and
Setup

press the ENTER button. It is switched to the selected device.
Move
Enter
If you cannot find a device you want, press the ▲ or ▼ button
Return
to select Searching Connections, then press the ENTER
button.
Setup
The meassage Configuring Anynet+ connection is
Anynet+ (HDMI-CEC)
: On

displayed. When searching devices completes, the connected
devices are listed in the Anynet+ menu.
Auto Turn Off : Yes

Switching to the selected devices may take up to 2 minutes.
Searching Connections 
You cannot cancel the operation during the switching
operation.
Move
Enter
Return
The time required to scan for devices is determined by the
number of connected devices.
When the device scan is complete, the number of found devices is not displayed.
Although the TV automatically scans devices when it is turned on using the POWER button, devices
connected when the TV is on or under a specific circumstance are not displayed in the device list.
Therefore select Searching Connections menu to search devices.
If you have selected external input mode by pressing the SOURCE button, you cannot use the
Anynet+ function. Make sure to switch to an Anynet+ device by using the TOOLS button.
English - 34
책1.indb 34
Continued...
2008-03-17 오후 4:21:43
Anynet+ Menu
The Anynet+ menu changes depending on the type and status of the Anynet+ devices connected
to the TV.
Anynet+ Menu
View TV
Select Device
Record
Menu on Device
Device Operation
Receiver
Setup
Description
Switches from Anynet+ to TV broadcast mode.
Your TV connects to the corresponding device.
Starts a recording. (This menu works only for a device supporting
recording.)
Shows the menu of the connected device.
Example. When a DVD Recorder is connected, the DVD Recorder’s
title menu appears.
Shows the play control menu of the connected device.
Example. When a DVD Recorder is connected, the play control
menu of the DVD Recorder appears.
Sound is output through the receiver.
You can set the environment for using Anynet+.
TV Remote Control Buttons Available in Anynet+ Mode
Device Type
Anynet+ Device
Operating Status
After switching to the
device, when the menu of
the corresponding device is
displayed on the screen.
Available Buttons
Numeric buttons
▲/▼/◄/►/ENTER buttons
Colour buttons
EXIT button
After switching to the device,
while playing a file
(Backward search)
(Forward search)
(Stop)
W.LINK
/
(Play/Pause)
Device with built-in Tuner
After switching to the device,
when you are watching a TV
W.LINK
program
Audio Device
When Receiver is activated
W.LINK
W.LINK
P
W.LINK
/
button
W.LINK

/
button
MUTE button
W.LINK
W.LINK
Anynet+ function only works when the remote control is set to TV.
➢The
button works only while in the recordable state.
➢The
cannot control Anynet+ devices using the buttons on the side of the TV. You can control Anynet+
➢You
devices only using the TV remote control.
TV remote control may not work under certain conditions. In this case, re-select the Anynet+
➢The
device.
Anynet+ functions don’t operate for the products from other manufacturers.
➢The
mode, the colour buttons may not work properly.
➢InTheAnynet+
,
operations may differ depending on the device.
➢
W.LINK
W.LINK
Recording
W.LINK
W.LINK
You can make a recording of a TV program using a recorder.
Press the
button.
Recording begins. (Only when
the Anynet+ enabled recording device is connected.)
W.LINK
The current TV program is recorded in the Watching TV status. If you are watching video from
another device, the video from the device is recorded.
You can also record the source streams by selecting Record after pressing the TOOLS button.
Before recording, check whether the antenna jack is properly connected to the recording device.
For the antenna connection to the recording device, refer to its user manual.
➢
➢
➢
English - 35
책1.indb 35
2008-03-17 오후 4:21:44
Listening through a Receiver
You can listen to sound through a receiver instead of the TV speaker.
1
2
3
4
➢
➢
➢
➢
Press the MENU button to display the menu.
TV
P 1
Press the ▲ or ▼ button to select Input, then press the ENTER button.
View TV
Press the ▲ or ▼ button to select Anynet+ (HDMI-CEC), then press the

Select Device
ENTER button.
Record


Menu on Device
Press the ▲ or ▼ button to select Receiver, then press the ENTER button.
Device Operation

Press the ◄ or ► button to select to On, then press the ENTER button.
Receiver :On

Now you can listen to sound through the receiver.
Setup

Press the EXIT button to exit.
Move
Enter
When the receiver is set to On, you can listen to the TV sound through the
Return
2-channel receiver.
If the receiver is exclusively for a home theater only (supporting audio only),
it may not appear in the device list.
In case of a content with copyright problem, listening through the receiver may not properly operate.
When listening through the receiver, there are restrictions for using the PIP and audio-related menu.
Check Points before Requesting Service
Symptom
Anynet+ does not work.
I want to start Anynet+.
I want to exit Anynet+.
The Connecting to Anynet+
device… message appears
on the screen.
The Anynet+ device does
not play.
The connected device is not
displayed.
The TV program cannot be
recorded.
Solution
■ Check if the device is an Anynet+ device. The Anynet+ system
supports Anynet+ devices only.
■ Connect only one receiver.
■ Check if the Anynet+ device power cord is properly connected.
■ Check the Anynet+ device’s Video/Audio/HDMI Cable connections.
■ Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+
setup menu.
■ Check whether the TV remote control is in TV mode.
■ Check whether it is Anynet+ exclusive remote control.
■ Anynet+ doesn’t work at a certain condition. (Searching channels)
■ When connecting or removing the HDMI cable, please make sure
to search devices again or restart your TV.
■ Check if the Anynet+ Function of Anynet+ device is set on.
■ Check if the Anynet+ device is properly connected to the TV and check
if the Anynet+ (HDMI-CEC) is set to On in the Anynet+ Setup menu.
■ Press the TV button on the TV remote control to switch to TV. Then
press the TOOLS button to show the Anynet+ menu and select a
menu you want.
■ Select View TV in Anynet+ menu.
■ Press the SOURCE button on the TV remote control and select a
device other than Anynet+ devices.
■ Press any of P, CH LIST, PRE-CH, and such to change to the
TV mode. (Note that the channel button operates only when a
tuner-embedded Anynet+ device is not connected.)
■ You cannot use the remote control when you are configuring
Anynet+ or switching to a view mode.
■ Use the remote control when the Anynet+ setting or switching to
view mode is complete.
You cannot use the play function when an auto channel scan is in
progress. Stop the currently running function.
■ Check whether or not the device supports Anynet+ functions.
■ Check whether or not the HDMI Cable is properly connected.
■ Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+
setup menu.
■ Search Anynet+ devices again.
■ You can connect an Anynet+ device using the HDMI Cable only.
Some HDMI cables may not support Anynet+ functions.
Check whether the antenna jack on the recording device is properly
connected.
English - 36
책1.indb 36
2008-03-17 오후 4:21:45
Teletext Feature (depending on the model)
Most television stations provide written information services
via teletext. The index page of the teletext service gives you
information on how to use the service. In addition, you can select
various options to suit your requirements by using the remote
control buttons.
teletext information to be displayed correctly, channel reception
☛For
must be stable. Otherwise, information may be missing or some
pages may not be displayed.
1 TV
Exit from the teletext display (depending on the model)
2
(store)
Used to store the teletext pages.
3
(size)
Press to display the double-size letters in the upper half of the
screen. For lower half of the screen, press it again.
To display normal screen, press it once again.
4
(reveal)
Used to display the hidden text (answers to quiz games, for
example). To display normal screen, press it again.
5 Coloured buttons (red/green/yellow/blue)
If the FASTEXT system is used by a broadcasting company, the
different topics covered on a teletext page are colour-coded and
can be selected by pressing the coloured buttons. Press one of
them corresponding to the required. The page is displayed with
other coloured information that can be selected in the same way.
To display the previous or next page, press the corresponding
coloured button.
6
(teletext on/mix)
Press to activate teletext mode after selecting the channel providing
the teletext service. Press it twice to overlap the teletext with the
current broadcasting screen.
7
(mode)
Press to select the teletext mode (LIST/FLOF).
If you press it in the LIST mode, it switches into the List save mode.
In the List save mode, you can save teletext page into list using the
(store) button.
8
(sub-page)
Used to display the available sub-page.
9
(page up)
Used to display the next teletext page.
0
(page down)
Used to display the previous teletext page.
!
(index)
Used to display the index (contents) page at any time while you are viewing teletext.
@
(hold)
Used to hold the display on a given page if the selected page is
linked with several secondary pages
which follow on automatically. To resume, press it again.
#
(cancel)
Used to display the broadcast when searching for a page.
can change teletext pages by pressing the numeric buttons on
➢ You
the remote control.
Continued...
English - 37
책1.indb 37
2008-03-17 오후 4:21:47
The teletext pages are organized according to six categories:
Part
A
B
C
D
E
F
Contents
Selected page number.
Broadcasting channel identity.
Current page number or search indications.
Date and time.
Text.
Status information.
FASTEXT information.
information is often divided between several pages
➢ Teletext
displayed in sequence, which can be accessed by:
Entering the page number
Selecting a title in a list
Selecting a coloured heading (FASTEXT system)
➢ Press the TV button to exit from the teletext display.
English - 38
책1.indb 38
2008-03-17 오후 4:21:48
Wall Mount Kit Specifications (VESA)
Install your wall mount on a solid wall perpendicular to the floor.
When attaching to other building materials, please contact your nearest dealer.
If installed on a ceiling or slanted wall, it may fall and result in severe personal injury.
Product Family
inch
VESA Spec. (A * B)
Standard Screw
23 ~ 26
200 * 100
M4
32 ~ 40
200 * 200
M6
46 ~ 52
400 * 400
600 * 400
57
700 * 400
(No VESA)
LCD-TV
PDP-TV
➢
➢
➢
➢
➢
➢
➢
➢
Quantity
4
M8
57 ~ 70
800 * 400
80 ~
1400 * 800
42 ~ 58
400 * 400
600 * 400
63
676 * 407
(No VESA)
63 ~ 70
800 * 400
4
80 ~
1400 * 800
4
4
M8
6
We provided the standard dimensions for wall mount kits as shown in the table above.
When purchasing our wall mount kit, a detailed installation manual and all parts necessary for
assembly are provided.
Do not use screws longer than the standard dimension, as they may cause damage to the inside of
the TV set.
For wall mounts that do not comply with the VESA standard screw specifications, the length of the
screws may differ depending on their specifications.
Do not use screws that do not comply with the VESA standard screw specifications.
Do not use fasten the screws too strongly, this may damage the product or cause the product to fall,
leading to personal injury. Samsung is not liable for these kinds of accidents.
Samsung is not liable for product damage or personal injury when a non-VESA or non-specified wall
mount is used or the consumer fails to follow the product installation instructions.
Our 57” and 63” models do not comply with VESA Specifications. Therefore, you should use our
dedicated wall mount kit for this model.
Do not exceed 15 degrees tilt when mounting this TV.
Do not install your Wall Mount Kit while your TV is turned on.
It may result in personal injury due to electric shock.
English - 39
책1.indb 39
2008-03-17 오후 4:21:48
Wall- mount adjustment (Sold separately)
Once the auto wall mount is installed, the position of your TV can be easily adjusted.
Rear Panel
Auto Wall-Mount
Serial Cable(1P to 1P)(Not supplied)
Entering the menu
1
Press the ▲, ▼, ◄ or ► button on your remote control.
➢ The Wall Mount Adjustment screen is displayed.
➢ If the Wall Mount Adjustment screen is not displayed when
clicking on a direction button while watching your TV, use
the menu to display that screen.
• Press the MENU button to display the menu. Press the
▲ or ▼ button to select Setup, then press the ENTER
button.
• Press the ▲ or ▼ button to select Wall-Mount
Adjustment, then press the ENTER button.
TV
Setup
Plug & Play
Language
:English
Time Light Effect
:In Watching TV
Wall-mount Adjustment Melody
:Off
Entertainment
:Off
Energy Saving
:Off
PIP
Move
Enter
Return
2
Wall-Mount Adjustment
5
►
4
►
►
3
►
Remembering the Position
Adjust to the desired position using the ▲, ▼, ◄, ► buttons.
➢ If you press an arrow button when no OSD is displayed on
the TV screen, the Adjustment screen appears.
➢ Press the INFO button to reset. Press the ◄ or ► button
to select Yes, then press the ENTER button. The position
is initialized to the default setting.
Press the blue button.
Press the ▲ and ▼ buttons to select a save mode from either
Position1, Position2 or Position3 in order to save the
current position.
➢ To not save the current position, press the RETURN
button.
➢ When selecting a save mode, you cannot use the Colour
buttons.
Press the ENTER button to save.
➢ When Position1 is selected, the message Current
position saved as Position1 is displayed.
Press the ENTER button.
➢ The saved Position appears on the left side of the OSD.









Position
Adjust
1
Save
2
3
Center
Save
Select a mode to Save.
Position 1
Position 2
Position 3
MOVE
Enter
Return
Continued...
English - 40
책1.indb 40
2008-03-17 오후 4:21:50
Moving to the remembered position
Complete Step 1 of Entering the menu.
Wall-Mount Adjustment
Pressing a Colour (Red, Green, Yellow) button moves the auto wall
Position 1
mount to the saved position.
➢ You can move the wall mount to one of the 3 pre-set positions
by pressing the Red (Position 1), Green (Position 2) or Yellow
(Position 3) buttons.
➢ If you adjust the positon after moving to a pre-set position, the
Position
1
2
3
position display will disappear.
Adjust
Save
Center
For installation, refer to the Installation Manual provided with the wall
mount.
For product installation and the installation and moving of the wall mount, make sure to consult a specialized
installation company.
This installation manual is to be used when attaching the wall mount to a wall. When attaching to other building
materials, please contact your nearest dealer.
The auto wall mount will not work when Anynet+ is operating.
42 inches model is not compatible with the older wall mount model (WMN5090A).
►
1
2
►
►
►
➢
➢
➢
➢
➢
How to assemble the Stand-Base (depending on the model)
Using the screws for securing the stand base and the monitor, firmly
attach the monitor to the stand base.
(The exterior of the set may be different from the picture.)
Warning
Firmly secure the stand to the TV before
moving it, as the stand may fall and could
cause serious injury.
Two or more people should carry
the TV. Never lay the TV on the floor
because of possible damage to the
screen.
Always store the TV upright.
In case of installing your
TV on the wall, close the
cover (1) on the stand-base
connection part using two
screws for hiding.
➢
English - 41
책1.indb 41
2008-03-17 오후 4:21:52
Troubleshooting
Before contacting the Samsung after-sales service, perform the following simple checks.
If you cannot solve the problem using the instructions below, note the model and serial number of
the television and contact your local dealer.
No sound or picture
 Check that the mains lead has been connected to a wall socket.
 Check that you have pressed the (Power) button (On/Off) on the front panel or press the POWER
button on the remote control.
 Check the picture contrast and brightness settings.
 Check the volume.
 Check if TV Speaker is set to Off.
Normal picture but no sound
 Check the volume.
 Check whether the volume MUTE button on the remote control has been pressed.
No picture or black and white picture
 Adjust the colour settings.
 Check that the broadcast system selected is correct.
Sound and picture interference
 Try to identify the electrical appliance that is affecting the television, then move it further away.
 Plug the television into a different main socket.
Blurred or snowy picture, distorted sound
 Check the direction, location and connections of your aerial.
This interference often occurs due to the use of an indoor aerial.
Remote control malfunctions
 Replace the remote control batteries.
 Clean the upper edge of the remote control (transmission window).
 Check that the “+” and “–” ends of the batteries are inserted correctly.
 Check that the batteries are drained.
Screen is black and power indicator light blinks steadily
 On your computer check; Power, Signal Cable.
 The TV is using its power management system.
 Move the computer’s mouse or press any key on the keyboard.
 On your equipment check (STB, DVD, etc) ; Power, Signal Cable.
 The TV is using its power management system.
 Press the Source button on the panel or remote control.
 Turn the TV off and on.
The damaged picture appears in the corner of the screen.
 If Just Scan is selected in some external devices, the damaged picture may appear in the corner of
the screen. This symptom is caused by external devices, not TV.
The “Resets all settings to the default values” message appears.
 This appears when you press and hold the EXIT button for a while. The product settings are reset to
the factory defaults.
English - 42
책1.indb 42
2008-03-17 오후 4:21:52
Specifications
The descriptions and characteristics in this booklet are given for information purposes only and
are subject to modification without notice.
Model Name
PS42A450
PS50A450
Screen Size (Diagonal)
PC Resolution
42 inch
50 inch
1024 x 768 @ 60 Hz
1360 x 768 @ 60 Hz
Sound (Output)
Dimension (WxHxD)
Body
With stand
Weight
Body
With stand
Environmental Considerations
Operating Temperature
Operating Humidity
Storage Temperature
Storage Humidity
10W x 2
1055 x 668 x 94 mm
1055 x 725 x 316 mm
1231 x 756 x 95 mm
1231 x 813 x 316 mm
27 kg
31 kg
35 kg
37 kg
10 °C to 40 °C (50 °F to 104 °F)
10% to 80%, non-condensing
-20 °C to 45 °C (-4 °F to 113 °F)
5% to 95%, non-condensing
➢ This device is a Class B digital apparatus.
Design and specifications are subject to change without prior notice.
For the power supply and Power Consumption, refer to the label attached to the product.
English - 43
책1.indb 43
2008-03-17 오후 4:21:53
This page is intentionally
left blank.
책1.indb 44
2008-03-17 오후 4:21:53
Download PDF

advertising