Samsung | SP-62T8HC | Samsung SP-62T8HC User Manual

COLOUR
TELEVISION
SP42W4/42W5
SP43J9/43T6/43T7/43T8/43W6
SP47Q7/47W1/47W3
SP48T6
SP52Q7
SP54J9/54T6/54T7/54T8
SP55W3/55W9
SP62J9/62T6/62T8
SP65W3
Owner’s Instructions
Before operating the unit,
please read this manual thoroughly,
and retain it for future reference.
ON-SCREEN MENUS
PICTURE IN PICTURE
TELETEXT
Important Warranty Information Regarding Television
Format Viewing
ENG
Standard screen format televisions (4:3, the aspect ratio of the screen width to height) are
primarily designed to view standard format full-motion video. The images displayed on them
should primarily be in the standard 4:3 ratio format and constantly moving. Displaying stationary
graphics and images on screen, such as the dark top and bottom letterbox bars (wide screen
pictures), should be limited to no more than 15% of the total television viewing per week.
Wide screen format televisions (16:9, the aspect ratio of the screen width to height) are
primarily designed to view wide screen format full-motion video. The images displayed on them
should primarily be in the wide screen 16:9 ratio format, or expanded to fill the screen if your
model offers this feature, and constantly moving. Displaying stationary graphics and images on
screen, such as the dark side-bars on non-expanded standard format television video and
programming, should be limited to no more than 15% of the total television viewing per week.
Additionally, viewing other stationary images and text such as stock market reports, video
game displays, station logos, web sites or computer graphics and patterns, should be limited as
described above for all televisions. Displaying any stationary images that exceed the above
guidelines can cause uneven aging of picture tubes (CRTs) that leave subtle, but permanent
burned-in ghost images in the television picture. To avoid this, vary the programming and
images, and primarily display full screen moving images, not stationary patterns or dark bars.
On television models that offer picture sizing features, use these controls to view the different
formats as a full screen picture.
B
e careful in the selection and duration of television formats used for viewing. Uneven CRT
aging as a result of format selection and use, as well as other burned-in images, is not covered by
your Samsung limited warranty.
2
Safety Instructions
ENG
◆ Do not expose the television to extreme temperature conditions or to extreme humidity conditions.
◆ Do not expose the television to direct sunlight and other sources of heat.
◆ Do not expose the television to any liquids.
◆ Never put objects of any kind into the television, and do not place a water-containing vessel on the
television.
◆ During a storm conditions (especially when there is lightning) unplug the television from the mains
socket and aerial.
◆ Do not step on or twist the power cord.
◆ Do not overload wall outlets or extension cords as this can result in a risk of fire or electric shock.
◆ Please use a soft and dry cloth (not containing volatile matter) when you clean the TV.
◆ If the television is broken, do not try to repair it yourself. Contact qualified service personnel.
◆ If the remote control is not used for a long period of time, remove the batteries and store it in a
cool, dry place.
◆ Do not drop the remote control.
☛
Displaying any stationary images that exceed the long time, it can cause uneven aging of
picture tubes that leave subtle, but permanent burned-in ghost images in the television
picture. To avoid this, vary the programming and images, and primarily display full
screen moving images, not stationary patterns or dark bars.
This device is not for use in industrial environments.
Caution
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO PREVENT ELECTRICAL SHOCK,
DO NOT REMOVE REAR COVER, NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
WARNING: TO PREVENT DAMAGE WHICH MAY RESULT
IN FIRE OR SHOCK HAZARD. DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
The lightning flash and arrow head
within the triangle is a warning sign
alerting you of “dangerous voltage”
inside the product.
The exclamation point within the
triangle is a warning sign alerting
you of important instructions
accompanying the product.
☛
The main voltage is indicated on the
rear of the TV set and the frequency is
50 or 60Hz.
3
ENG
Contents (continued)
◆ FOREWORD
■
■
■
Important Warranty Information Regarding Television Format Viewing ........
Safety Instructions .........................................................................................
Caution ..........................................................................................................
2
3
3
◆ CONNECTING AND PREPARING YOUR TELEVISION
■
■
■
■
■
■
■
■
■
■
■
■
■
Control Panels ............................................................................................... 6~7
Using a Display Deck ....................................................................................
8
Connection Panels ........................................................................................
9
Infrared Remote Control ................................................................................
10
Inserting the Batteries in the Remote Control................................................
11
Connecting to an Aerial or Cable Television Network ...................................
11
Switching Your Television On and Off...........................................................
12
Placing Your Television in Standby Mode .....................................................
12
Becoming Familiar with the Remote Control .................................................
13
Plug and Play Feature ................................................................................... 14~15
Viewing the Demonstration............................................................................
16
Choosing Your Language..............................................................................
16
Adjusting Convergence .................................................................................
17
◆ SETTING THE CHANNELS
■
■
■
■
■
Storing Channels Automatically.....................................................................
18
Sorting the Stored Channels .........................................................................
19
Storing Channels Manually............................................................................ 20~21
Skipping Unwanted Channels .......................................................................
22
Fine Tuning Channel Reception ....................................................................
23
◆ USING YOUR TELEVISION (continued)
■
■
■
■
■
■
Freezing the Current Picture .........................................................................
Changing the Picture Standard .....................................................................
Adjusting the Picture Settings........................................................................
Setting the Blue Screen Mode.......................................................................
Extra Picture Settings ....................................................................................
- SCAN MODE
- DIGITAL NR
- LNA (Low Noise Amplifier)
Selecting the Picture Size (depending on the model)....................................
Symbols
Press
4
☛
Important
➢
Note
24
24
25
25
26
27
ENG
Contents
◆ USING YOUR TELEVISION
■
■
■
■
■
■
■
■
■
Changing the Sound Standard ......................................................................
28
Adjusting the Sound Settings ........................................................................
29
Setting the Dolby Pro Logic (depending on the model) .................................
30
Extra Sound Settings.....................................................................................
31
- AUTO VOLUME
- MELODY
- VIRTUAL DOLBY
Selecting the Sound Mode (depending on the model) ..................................
32
Setting the Sleep Timer .................................................................................
33
Setting and Displaying the Current Time.......................................................
34
Switching the Television On and Off Automatically .......................................
35
Viewing the Picture In Picture (PIP) .............................................................. 36~37
◆ USING THE TELETEXT FEATURE
■
■
■
■
■
Teletext Feature ............................................................................................
Displaying the Teletext Information ...............................................................
Selecting Display Options..............................................................................
Selecting a Teletext Page..............................................................................
Storing Teletext Pages ..................................................................................
38
38
39
40
41
◆ ADDITIONAL INFORMATION ON CONNECTIONS
■
■
■
■
■
■
■
Connecting to the External Input/Outputs......................................................
Connecting to the DVD Input.........................................................................
Connecting to the Audio Output ....................................................................
Connecting to the RCA Input.........................................................................
Connecting to the S-Video Input....................................................................
Connecting Additional Speakers ...................................................................
Viewing Pictures From External Sources ......................................................
42
43
43
44
44
45
45
◆ RECOMMENDATIONS FOR USE
■
■
■
Programming the Remote Control for Other Components ............................
- TV Remote Control Codes .........................................................................
- VCR Remote Control Codes ......................................................................
- Cable Box (CATV) Remote Control Codes ................................................
- DVD Remote Control Codes ......................................................................
SCART Connector Wiring (AV1) ...................................................................
Troubleshooting: Before Contacting Service Personnel................................
5
46
47
48
49
49
50
51
Control Panels (depending on the model)
➢
ENG
The actual configuration on your television may be different,
depending on your model.
( a ) Input Source Selection
(f)
( b ) Menu Display
( g ) Temporary Sound Switch Off
( c ) Previous Channel
( h ) Remote Control Sensor
( d ) Next Channel
(i)
Power On/Off
( e ) Volume Decrease
(j)
Standby & Timer Indicator
6
Volume Increase
Control Panels (depending on the model)
➢
The actual configuration on your television may be different,
depending on your model.
ENG
( a ) Input Source Selection
(f)
( b ) Menu Display
( g ) Temporary Sound Switch Off
( c ) Previous Channel
( h ) Remote Control Sensor
( d ) Next Channel
(i)
Power On/Off
( e ) Volume Decrease
(j)
Standby & Timer Indicator
Volume Increase
7
Using a Display Deck (depending on the model)
ENG
You can display a VCR or DVD Player, etc. by using the display
deck.
SP47W3/55W3/65W3
SP47W3/55W3/65W3
1
Press the symbol “
2
Hold the center of the door and lift it up in the direction of arrow till
a ‘ttok’ sound sounds.
3
After placing a component you have in the display deck, hold the
center of the door and pull it down.
4
Shut the door by pressing the symbol “
” at the center of the display deck.
”.
SP54T8/55W9/62T8
SP54T8/55W9/62T8
1
Hold the center of the door and lift it up in the direction of arrow.
2
After placing a component you have in the display deck, hold the
center of the door and pull it down.
➣
8
You should display only the component that is within
126mm high. When displaying a component in the
display deck, please space it out 30mm from the front,
20mm from either end.
Connection Panels (depending on the model)
➢
The actual configuration on your TV may be different, depending on
your model.
Front of the TV
ENG
Side of the TV
a
Video Input
Perfect Focus
S-Video Input
Audio Inputs
Center Speaker Connectors (Option)
Rear of the TV
Rear Speaker Connectors
75Ω Coaxial Connector for Aerial
or Cable Network
Audio/Video Monitor Outputs
S-Video Input
RCA Audio/Video Inputs
Audio Outputs
SCART Audio/Video Input/Output
DVD Inputs
9
Infrared Remote Control
ENG
Power
TELEVISION STANDBY
TV
VCR
Cable
DVD
SET
MAKE THE REMOTE CONTROL
WORKS FOR TV, VCR, CABLE,
DVD PLAYER
REMOTE CONTROL SETUP
NUMERIC BUTTONS FOR
DIRECT ACCESS
(CHANNEL/TELETEXT PAGE)
ONE, TWO, OR THREE-DIGIT
CHANNEL SELECTION
(DEPENDING ON THE MODEL)/
TELETEXT STORE (OPTION)
TV
Surround
S.STD
P.STD
S.Mode
TUNER/CABLE NETWORK SELECTION
FASTEXT TOPIC SELECTION
SOUND MODE SELECTION
SURROUND ON/OFF DIRECTLY
PICTURE EFFECT SELECTION
SOUND EFFECT SELECTION
NEXT CHANNEL/
TELETEXT NEXT PAGE
VOLUME INCREASE
Mute
Still
VOL
TEMPORARY SOUND SWITCH OFF
P
PICTURE FREEZE
PREVIOUS CHANNEL/
TELETEXT PREVIOUS PAGE
VOLUME DECREASE
Menu
Video
EXTERNAL INPUT SELECTION/
TELETEXT MODE (LIST/FLOF)
SELECTION (OPTION)
MENU DISPLAY/
PROGRAMME SELECTION BY NAME
CONTROL THE CURSOR IN THE
ON-SCREEN MENU
CHANGE CONFIRMATION
ON-SCREEN MENUS DISPLAY/
TELETEXT REVEAL
Display
P.Size
NOT AVAILABLE
TELETEXT DISPLAY/
MIX BOTH TELETEXT INFORMATION
AND THE NORMAL BROADCAST
VCR/DVD FUNCTIONS;
- STOP
- REWIND
- PLAY/PAUSE
- FAST FORWARD
TELETEXT SUB-PAGE
PICTURE SIZE/TELETEXT SIZE
AUTOMATIC SWITCH-OFF
Text/Mix
Info.
Sleep Perfect Focus
PIP
ON
Scan
Swap
Locate
AUTOMATIC ADJUST THE
CONVERGENCE
PIP FUNCTIONS;
- PIP ON/OFF
- CHANNEL SCAN
- INTERCHANGE THE MAIN AND
SUB PICTURE
- LOCATION SELECTION
TELETEXT PAGE HOLD
TELETEXT CANCEL
➢
10
The performance of the
remote control may be
affected by bright light.
Inserting the Batteries in the Remote Control
ENG
You must insert or replace the batteries in the remote control when
you:
◆ Purchase the television
◆ Find that the remote control is no longer operating
correctly
1
Remove the cover on the rear of the remote control by pressing
the symbol downwards and then pulling firmly to remove it.
2
Insert two R03, UM4, “AA” 1.5V or equivalent batteries taking care
to respect the polarities:
◆ + on the battery against + on the remote control
◆ - on the battery against - on the remote control
3
Replace the cover by aligning it with the base of the remote
control and pressing it back into place.
Connecting to an Aerial or Cable Television Network
To view television channels correctly, a signal must be received by
the set from one of the following sources:
◆ An outdoor aerial
◆ A cable television network
◆ A satellite network
1
In the first three cases, connect the aerial or network input cable to
the 75Ω coaxial socket on the rear of the television.
2
If you are using an indoor aerial, you may need to turn it when
tuning your television until you obtain a picture that is both sharp
and clear.
For further details, refer to:
◆ “Storing Channels Automatically” on page 18
◆ “Storing Channels Manually” on page 20
Rear of the TV
or
Cable Television
Network
11
Switching Your Television On and Off
ENG
The mains lead is attached to the rear of your television.
1
Plug the mains lead into an appropriate socket.
2
Press the POWER ( I ) button on the front of the television.
Power
TV
VCR
Cable
DVD
SET
main voltage is indicated on the rear of the television
➣ The
and the frequency is 50 or 60Hz.
Result:
3
The Standby indicator on the front of the television
lights up.
Press the Power ( ) button on the remote control to switch the
television on.
Result:
The programme that you were watching last is reselected automatically.
you have not yet stored any channels, No clear picture
➣ Ifappears.
Refer to “Storing Channels Automatically” on page
18 or “Storing Channels Manually” on page 20.
4
To switch your television off, press the POWER ( I ) button again.
Placing Your Television in Standby Mode
Your television can be placed in Standby mode, in order to reduce
the power consumption.
The Standby mode can be useful when you wish to interrupt
viewing temporarily (during a meal, for example).
Power
TV
VCR
Cable
DVD
SET
1
Press the Power ( ) button on the remote control.
Result:
2
To switch the television back on, simply press the Power ( )
button again.
☛
12
The screen is turned off and the Standby indicator on
the front of the television lights up in red.
Do not leave your television in Standby mode for long
periods of time (when you are away on holiday, for
example). Turn your television off by pressing the
POWER ( I ) button on the front of the television.
It is best to unplug the set from the mains and aerial.
Becoming Familiar with the Remote Control
ENG
The remote control is used mainly to:
◆ Change channels and adjust the volume
◆ Set up the television using the on-screen menu system
Power
The following table presents the most frequently used buttons and
their functions.
Button
Viewing Function
TV
VCR
Cable
DVD
SET
Menu Function
Used to display the next stored channel.
P
Used to display the previous stored channel.
to
-/--/---
Used to display the corresponding channels.
Used to select a channel numbered ten or over.
Press this button, and enter the two or three-digit channel
number (depending on the model).
TV
Surround
P.STD
S.STD
Mute
+
VOL
-
Used to increase the volume.
Mute
Used to switch the sound off temporarily.
To turn the sound back on, press this button again, or
VOL- or VOL+ button.
Menu
Used to display the
on-screen menu system.
▲
➛❿
▼
TV
Still
VOL
Used to decrease the volume.
S.Mode
P
Menu
Video
➣
-
Used to return to the previous
menu or normal viewing.
Used to...
◆ Display a submenu
containing selections for
the current menu option.
◆ Increase/reduce a menu
option value.
-
Used to confirm your choice.
Used to switch the
television on when it is
in Standby mode.
Used to exit from the menu
system and return to normal
viewing directly.
Display
P.Size
Text/Mix
Info.
Sleep Perfect Focus
PIP
ON
Scan
Swap
13
Locate
Plug and Play Feature
ENG
When the television is initially powered on, three basic customer
settings proceed automatically and subsequently: setting the
language, channel and clock.
PLUG & PLAY
1
ANT. INPUT : CHECK
SELECT
Result:
EXIT
AUTO STORE
AREA
SEARCH
If the television is in Standby mode, press the POWER ( ) button
on the remote control.
2
: ASIA W/EUROPE
: -/+
Select the appropriate language by pressing the ▼ or ▲ button.
Press the MENU button to enter the language.
Result:
➣
SELECT
ADJUST
EXIT
3
The message PLUG & PLAY is displayed. It flickers for
a little while and then LANGUAGE menu is automatically
displayed.
The message ANT. INPUT : CHECK is displayed.
If any language is not selected on the Language menu, the
Language menu will disappear about 30 seconds later.
Make sure that the antenna is connected to the TV.
Press the ➛ or ❿button.
Result:
The AUTO STORE menu is displayed with AREA is
selected.
TIME
CLOCK
TIMER
: -- : -- AM
: OFF
4
Select your country by pressing the ➛ or ❿ button.
To search the channels, select SEARCH by pressing the ▼ or ▲
button, and then press the ➛ or ❿ button.
Press the MENU button to stop the search.
Result:
SELECT
ADJUST
➣
EXIT
5
6
Refer to “Storing Channels Automatically” on page 18.
Press the ➛ or ❿ button to move to the hour or minute.
Set the hour or minute by pressing the ▼ or ▲ button.
➣
ENJOY YOUR WATCHING
Refer to “Setting and Displaying the Current Time” on page
34.
When you have finished, press the MENU button.
Result:
14
The TIME menu is displayed with CLOCK is selected.
The message ENJOY YOUR WATCHING is displayed,
and then the channel which has been stored will be
activated.
Plug and Play Feature
ENG
If you want to reset this feature...
FUNCTION
1
Press the MENU button.
Result:
2
The main menu is displayed.
Press the ▼ or ▲ button to select FUNCTION.
Result:
The options available in the FUNCTION group are
displayed.
3
Press the
4
Press the ▼ or ▲ button to select PLUG & PLAY. Press the
button.
Result:
LANGUAGE
TIME
: ENGLISH
CONVERGENCE
BLUE SCREEN
PLUG & PLAY
DEMONSTRATION
SELECT
ENTER
button.
This feature starts with the message PLUG & PLAY is
displayed.
15
√
√
: ON
√
√
EXIT
Viewing the Demonstration
ENG
Menu
To become familiar with the various menus provided by your
television, you can view the inbuilt demonstration.
Video
1
Press the MENU button.
Result:
2
Display
Press the ▼ or ▲ button to select FUNCTION.
P.Size
Result:
FUNCTION
LANGUAGE
TIME
: ENGLISH
√
√
: ON
CONVERGENCE
BLUE SCREEN
PLUG & PLAY
DEMONSTRATION
SELECT
The main menu is displayed.
3
Press the
4
Press the ▼ or ▲ button to select DEMONSTRATION. Press the
button.
Result:
√
√
ENTER
The options available in the FUNCTION group are
displayed.
➣
EXIT
button.
Each of the menu options is displayed in turn.
When you wish to exit from the demonstration, press the TV
button on the remote control.
Choosing Your Language
FUNCTION
LANGUAGE
TIME
: ENGLISH
CONVERGENCE
BLUE SCREEN
PLUG & PLAY
DEMONSTRATION
SELECT
When you start using your television for the first time, you must
select the language which will be used for displaying menus and
indications.
ADJUST
√
√
: ON
1
Press the MENU button.
Result:
√
√
EXIT
2
Press the ▼ or ▲ button to select FUNCTION.
Result:
3
Press the
Result:
4
Press the
Result:
5
16
The main menu is displayed.
The options available in the FUNCTION group are
displayed.
button.
The LANGUAGE is selected.
button again.
The languages available are listed.
Press the ▼ or ▲ button to select the appropriate language.
Adjusting Convergence
ENG
If the color appears spread out or “smeared” on the screen, the
convergence probably needs alignment. Be sure to use the remote
control for the convergence adjustments. (The Convergence
Adjustment can not be made by using the control buttons on the
front panel.)
1
Press the MENU button.
The main menu is displayed.
Result:
2
Press the ▼ or ▲ button to select FUNCTION.
The options available in the FUNCTION group are
Result:
displayed.
3
Press the
FUNCTION
LANGUAGE
TIME
CONVERGENCE
BLUE SCREEN
PLUG & PLAY
DEMONSTRATION
SELECT
: ENGLISH
√
√
: ON
√
√
ENTER
button.
4
Press the ▼ or ▲ button to select CONVERGENCE. Press the
button.
The options available in the CONVERGENCE group are
Result:
displayed with RED is selected.
5
Press the
button again.
A crosshair pattern is appeared.
Result:
6
Adjust convergence by using your remote control.
EXIT
CONVERGENCE
MANUAL CONVERGENCE
RED
√
BLUE
√
PERFECT FOCUS
√
SELECT
◆ Use the ▼/▲/➛/❿ buttons to all directions for select the
position.
ENTER
EXIT
PLEASE USE REMOTE CONTROL
RED
◆ Press the “0” button to select red or blue convergence.
◆ To move the line so that it is superimposed on the horizontal
or vertical center-line, use the volume up/down (VOL +/-) and
channel up/down (P
/
) buttons (i.e., make a signal
horizontal or vertical line that is as white as possible).
POSITION
0:R/B
UP/DOWN
L/R
EXIT
◆ Press the MENU button to exit.
CONVERGENCE
You can adjust convergence automatically for the optimum in the
factory.
7
Select PERFECT FOCUS in the FUNCTION group, then press the
button.
Perform Perfect Focus in the following sequence:
Result:
green ➞ red ➞ blue.
After the cursor flickers for one second, the perfect
focus feature ends.
➣
➣
MANUAL CONVERGENCE
RED
√
BLUE
√
PERFECT FOCUS
√
SELECT
ENTER
EXIT
You can also adjust simply by pressing the Perfect Focus
button.
◆ When the size of the sub picture is selected to the “12
PIP” or “3 PIP” mode, the Perfect Focus feature does
not work.
◆ If any error happens during Perfect Focus, then
perform Perfect Focus once again.
◆ If you can not make adjustments after Perfect Focus,
then make manual adjustments. Still you can not
make adjustments, contact your Service Center.
PERFECT FOCUS
PROGRESS : 1%
EXIT
Text/Mix
Info.
Sleep Perfect Focus
PIP
ON
Scan
Swap
17
Locate
Storing Channels Automatically
ENG
You can scan for the frequency ranges available to you (and
availability depends on your country). Automatically allocated
programme numbers may not correspond to actual or desired
programme numbers. However you can sort numbers manually and
clear any channels you do not wish to watch.
CHANNEL
√
√
√
√
√
AUTO STORE
MANUAL STORE
ADD/ERASE
FINE TUNE
SORT
SELECT
ENTER
1
Press the MENU button.
Result:
EXIT
2
Press the ▼ or ▲ button to select CHANNEL.
Result:
AUTO STORE
AREA
SEARCH
: ASIA W/EUROPE
: -/+
3
Press the
Result:
4
SELECT
ADJUST
SELECT
P 8 C-426 MHz
button again.
The options available in the AUTO STORE group are
displayed with AREA is selected.
Press the ▼ or ▲ button to select Search.
7
Press the ➛ or ❿ button to start the search.
EXIT
Result:
➢
22%
The horizontal bar is displayed, and then channels are
stored in an order which reflects their positions in the
frequency range. Finally, the search will end
automatically.
To stop the search before it has finished, press the MENU
button.
When searching and storing are complete, the SORT menu is
displayed.
◆ To sort the stored channels into the desired numerical order,
go to Step 6 of the “Sorting the Stored Channels” procedure
on page 19.
EXIT
◆ To exit from the channel store function without sorting the
channels, press the MENU button repeatedly until the menus
disappear.
SORT
SELECT
The AUTO STORE is selected.
6
8
FROM
TO
STORE
button.
Select your country by pressing the ➛ or ❿ button.
The countries are displayed in the following order:
ASIA W/EUROPE - CIS E/EUROPE - CHINA - HONGKONG/UK AUSTRALIA - NZ/INDONESIA - SOUTH AFRICA - AMERICA.
: ASIA W/EUROPE
: -/+
ADJUST
The options available in the CHANNEL group are
displayed.
5
AUTO STORE
AREA
SEARCH
Press the
Result:
EXIT
The main menu is displayed.
: P 1
: P--: ?
ADJUST
18
9
EXIT
When the channels have been stored, you can:
◆
◆
◆
◆
◆
Sort them in the order required (refer to page 19)
Assign a name to the stored channels (refer to page 20)
Clear a channel (refer to page 22)
Fine tune channel reception if necessary (refer to page 23)
Activate the Digital Noise Reduction feature (refer to page 26)
Sorting the Stored Channels
ENG
This operation allows you to change the programme numbers of
stored channels. This operation may be necessary after using auto
store. You can delete the channels you do not want to keep.
1
Press the MENU button.
Result:
2
3
4
Press the
6
7
SELECT
ENTER
EXIT
button.
SORT
button.
The options available in the SORT group are displayed
with FROM is selected.
Select the channel number that you wish to change by pressing
the ➛ or ❿ button repeatedly.
FROM
TO
STORE
SELECT
: P 1
: P--: ?
ADJUST
Press the ▼ or ▲ button to select TO. Select the new channel
number which you wish to identify by pressing the ➛ or ❿button
repeatedly.
Press the ▼ or ▲ button to select STORE. Select OK to confirm the
exchange of channel numbers by pressing the ➛ or ❿button.
Result:
8
√
√
√
√
√
The options available in the CHANNEL group are
displayed.
Press the ▼ or ▲ button to select SORT. Press the
Result:
5
The main menu is displayed.
Press the ▼ or ▲ button to select CHANNEL.
Result:
CHANNEL
AUTO STORE
MANUAL STORE
ADD/ERASE
FINE TUNE
SORT
EXIT
SORT
FROM
TO
STORE
: P
: P
: ?
1
3
The selected channel is exchanged with the one
previously stored to the chosen number.
For all the channels to move to the required channel numbers,
repeat steps 5 to 7 after selecting the FROM by pressing the ▼ or
▲ button.
SELECT
ADJUST
EXIT
SORT
FROM
TO
STORE
SELECT
: P 3
: P 1
: OK
ADJUST
19
EXIT
Storing Channels Manually
ENG
You can store the television channels, including those received via
cable networks.
CHANNEL
SELECT
When storing channels manually, you can choose:
√
√
√
√
√
AUTO STORE
MANUAL STORE
ADD/ERASE
FINE TUNE
SORT
ENTER
◆ Whether or not to store each of the channels found
◆ The programme number of each stored channel which
you wish to identify
EXIT
1
Press the MENU button.
Result:
MANUAL STORE
COLOUR SYSTEM
SOUND SYSTEM
SEARCH
CHANNEL
PROG.NO.
STORE
SELECT
:
:
:
:
:
:
ADJUST
AUTO
BG
105MHZ
C 6
P 3
?
EXIT
2
Press the ▼ or ▲ button to select CHANNEL.
Result:
Press the
4
Press the ▼ or ▲ button to select MANUAL STORE. Press the
button.
Result:
SELECT
ADJUST
:
:
:
:
:
:
AUTO
BG
105MHZ
C 6
P 3
?
5
button.
The options available in the MANUAL STORE group are
displayed with COLOUR SYSTEM is selected.
Indicate the broadcasting standard required by pressing the ➛ or
❿ button repeatedly.
Result:
The colour standards are displayed in the following
order:
AUTO - PAL - SECAM - NT4.43 - NT3.58.
EXIT
6
Press the ▼ or ▲ button to select SOUND SYSTEM. Select the
sound standard required by pressing the ➛ or ❿ button
repeatedly.
Result:
20
The options available in the CHANNEL group are
displayed.
3
MANUAL STORE
COLOUR SYSTEM
SOUND SYSTEM
SEARCH
CHANNEL
PROG.NO.
STORE
The main menu is displayed.
The sound standards are displayed in the following
order:
BG - DK - I - M.
Storing Channels Manually (continued)
ENG
7
If you know the number of the channel to be stored, see the
following steps.
◆ Press the t or ▲ button to select CHANNEL.
◆ Press the ❿ button.
◆ Press the ▼ or ▲ button to select C (Air channel) or S (Cable
channel).
◆ Press the ❿button.
◆ Press the ▼ or ▲ button to select indicate the required
number.
➣
8
If you do not know the channel numbers, select SEARCH by
pressing the ▼ or ▲ button. Press the ➛ or ❿ button to start the
search.
Result:
9
If no sound or abnormal sound, re-select the sound
standard required.
The tuner scans the frequency range until the first
channel or the channel that you selected is received
on your screen.
To assign a programme number to a channel, select PROG.NO. by
pressing the ▼ or ▲ button. Press the ➛ or ❿ button to find the
correct number.
10
To store the channel and associated programme number, select
STORE by pressing the ▼ or ▲ button. Press the ➛ or ❿ button to
select OK.
11
Repeat Steps 7 to 10 for each channel to be stored.
☛
MANUAL STORE
COLOUR SYSTEM
: AUTO
SOUND SYSTEM
SEARCH
CHANNEL
PROG.NO.
STORE
:
:
:
:
:
SELECT
◆ C (Real channel mode): You can select a channel by
entering the assigned number to each air broadcasting station
in this mode.
EXIT
MANUAL STORE
COLOUR SYSTEM
SOUND SYSTEM
SEARCH
CHANNEL
PROG.NO.
STORE
SELECT
:
:
:
:
:
:
SEARCH
AUTO
BG
105MHZ
C 6
P 3
?
EXIT
MANUAL STORE
COLOUR SYSTEM
SOUND SYSTEM
SEARCH
CHANNEL
PROG.NO.
STORE
SELECT
:
:
:
:
:
:
ADJUST
AUTO
BG
105MHZ
C 6
P 3
?
EXIT
MANUAL STORE
Channel mode
◆ P (Programme mode): When completing tuning, the
broadcasting stations in your area have been assigned to
position numbers from P00 to max P99. You can select a
channel by entering the position number in this mode.
ADJUST
BG
105MHZ
C 6
P 3
?
COLOUR SYSTEM
SOUND SYSTEM
SEARCH
CHANNEL
PROG.NO.
STORE
SELECT
ADJUST
◆ S (Cable channel mode): You can select a channel by
entering the assigned number for each cable channel in this
mode.
21
:
:
:
:
:
:
AUTO
BG
105MHZ
C 6
P 3
OK
EXIT
Skipping Unwanted Channels
ENG
You can exclude the channels you chosen from the channels you
scanned. When you scan through the stored channels, those you
have chosen to skip are not displayed.
CHANNEL
√
√
√
√
√
AUTO STORE
MANUAL STORE
ADD/ERASE
FINE TUNE
SORT
All of the channels that you do not specifically choose to skip are
displayed during scanning.
1
SELECT
ENTER
Press the MENU button.
EXIT
Result:
2
1
2
3
4
:
:
:
:
SELECT
ADDED
ADDED
ADDED
ADDED
ADJUST
SELECT
1
2
3
4
:
:
:
:
Press the
4
Press the ▼ or ▲ button to select ADD/ERASE. Press the
button.
EXIT
ERASED
ADDED
ADDED
ADDED
ADJUST
22
EXIT
The options available in the CHANNEL group are
displayed.
3
Result:
button.
The stored channels are displayed.
5
Press the ▼ or ▲ button to select the channel to add or erase.
If necessary, select ADDED or ERASED by pressing the ➛ or ❿
button.
6
Repeat Step 6 for each channel to be added or erased.
ADD/ERASE
P
P
P
P
Press the ▼ or ▲ button to select CHANNEL.
Result:
ADD/ERASE
P
P
P
P
The main menu is displayed.
Fine Tuning Channel Reception
ENG
If the reception is clear, you do not have to fine tune the channel,
as this is done automatically during the search and store operation.
If the signal is weak or distorted, you may have to fine tune the
channel manually.
1
Press the MENU button.
Result:
2
Press the ▼ or ▲ button to select CHANNEL.
Result:
3
4
The main menu is displayed.
Press the
SELECT
EXIT
FINE TUNE
TUNE
STORE
ERASE
: -/+
: ?
: ?
The options available in the FINE TUNE group are
displayed with TUNE is selected.
ADJUST
EXIT
To obtain a sharp and clear picture and good sound quality, press
the ➛ or ❿ button.
Result:
6
ENTER
button.
SELECT
5
√
√
√
√
√
The options available in the CHANNEL group are
displayed.
Press the ▼ or ▲ button to select FINE TUNE. Press the
button.
Result:
CHANNEL
AUTO STORE
MANUAL STORE
ADD/ERASE
FINE TUNE
SORT
The horizontal bar is displayed. Move the horizontal
bar’s cursor left or right by pressing the ➛ or ❿
button.
FINE TUNE
To memorise adjusted picture or sound, select STORE by pressing
the ▼ or ▲ button. Press the ➛ or ❿ button.
Result:
OK is displayed.
FINE TUNE
7
To erase adjusted picture or sound, select ERASE by pressing the
▼ or ▲ button. Press the ➛ or ❿ button.
Result:
OK is displayed.
TUNE
STORE
ERASE
SELECT
: -/+
: OK
: ?
ADJUST
EXIT
FINE TUNE
TUNE
STORE
ERASE
SELECT
: -/+
: ?
: OK
ADJUST
23
EXIT
Freezing the Current Picture
ENG
You can freeze the picture when watching a television programme
simply by pressing the “STILL” button.
Mute
➣
Still
VOL
P
Menu
To return to normal viewing, press this button again.
Video
Changing the Picture Standard
You can select the type of picture which best corresponds to your
viewing requirements.
PICTURE
MODE
œ
ADJUST
SCAN MODE
DIGITAL NR
LNA
√
DYNAMIC
√
: AUTO
: OFF
: OFF
1
Result:
2
SELECT
ADJUST
Press the MENU button.
Press the
3
PICTURE
œ
MODE
SELECT
STANDARD
√
ADJUST
P.STD
S.STD
Mute
Result:
P
24
The following picture effects are available:
DYNAMIC - STANDARD - MOVIE - CUSTOM.
EXIT
S.Mode
Still
VOL
The MODE is selected.
Select the required picture effect by pressing the ➛ or ❿ button
repeatedly.
√
: AUTO
: OFF
: OFF
TV
Surround
button.
EXIT
Result:
ADJUST
SCAN MODE
DIGITAL NR
LNA
The options available in the PICTURE group are
displayed.
➣
You can also set these options simply by pressing the
P.STD (Picture Standard) button.
Adjusting the Picture Settings
ENG
Your television has several settings which allow you to control
picture quality.
PICTURE
œ
MODE
1
Press the MENU button.
The options available in the PICTURE group are
Result:
displayed.
2
Press the
3
Press the ▼ or ▲ button to select ADJUST. Press the
The options available in the ADJUST group are
displayed with COLOUR TONE is selected.
Press the ➛ or ❿ button to select the option (COOL2, COOL1,
NORMAL, WARM1, WARM2).
5
Press the ▼ or ▲ button to select the option (CONTRAST,
BRIGHTNESS, SHARPNESS, COLOUR or TINT-NTSC only) to be
adjusted. Press the ➛ or ❿ button.
➣
ADJUST
EXIT
button.
4
Result:
√
: AUTO
: OFF
: OFF
button.
SELECT
Result:
√
DYNAMIC
ADJUST
SCAN MODE
DIGITAL NR
LNA
ADJUST
COLOUR TONE
CONTRAST
BRIGHTNESS
SHARPNESS
COLOUR
SELECT
: NORMAL
: 100
: 50
: 75
: 55
ADJUST
EXIT
The horizontal bar is displayed. Move the horizontal
bar’s cursor left or right by pressing the ➛ or ❿
button.
If you make any changes to these settings, the picture
standard is automatically switched to CUSTOM.
Setting the Blue Screen Mode
If no signal is being received or the signal is very weak, a blue
screen automatically replaces the noisy picture background.
If you wish to continue viewing the poor picture, you must set the
“BLUE SCREEN” mode to “OFF”.
1
2
Press the MENU button.
The main menu is displayed.
Result:
Press the ▼ or ▲ button to select FUNCTION.
The options available in the FUNCTION group are
Result:
displayed.
3
Press the
4
Press the ▼ or ▲ button to select BLUE SCREEN.
5
Select the required option (ON or OFF) by pressing the ➛ or ❿
button.
FUNCTION
LANGUAGE
TIME
: ENGLISH
CONVERGENCE
BLUE SCREEN
PLUG & PLAY
DEMONSTRATION
SELECT
ADJUST
button.
25
√
√
: ON
√
√
EXIT
Extra Picture Settings
ENG
◆ SCAN MODE
You will normally find that scan mode is best set to AUTO to
reduce any slight picture flicker. However, it is possible that
some occasional broadcasts (NTSC-M) may benefit by
changing the scan mode. AUTO, NATURAL, DIGITAL and
PROG. (Progressive) modes are available.
PICTURE
MODE
œ
ADJUST
SCAN MODE
DIGITAL NR
LNA
√
DYNAMIC
√
: AUTO
: OFF
: OFF
◆ DIGITAL NR
SELECT
ADJUST
If the signal received by your television is weak, you can
activate this feature to reduce any static and ghosting that
may appear on the screen.
EXIT
PICTURE
œ
MODE
SELECT
◆ LNA
√
DYNAMIC
This feature is very useful in the situation that the TV is used
in a weak signal and amplifies the TV signal in the weak
signal area, but not noise.
√
: AUTO
: ON
: OFF
ADJUST
SCAN MODE
DIGITAL NR
LNA
ADJUST
EXIT
1
Press the MENU button.
Result:
The options available in the PICTURE group are
displayed.
PICTURE
MODE
œ
ADJUST
SCAN MODE
DIGITAL NR
LNA
SELECT
ADJUST
26
√
DYNAMIC
√
: AUTO
: OFF
: ON
EXIT
2
Press the
3
Select the required option (SCAN MODE, DIGITAL NR, or LNA) by
pressing the ▼ or ▲ button.
4
Press the ➛ or ❿ button to change the setting.
button.
◆ SCAN MODE : AUTO, NATURAL, DIGITAL, PROG.(Progressive)
◆ DIGITAL NR : OFF or ON (activating)
◆ LNA : OFF or ON (activating)
Selecting the Picture Size (depending on the model)
ENG
You can select the picture size which best corresponds to your
viewing requirements simply by pressing the “P.Size” button.
Display
Depending on the model, the following picture sizes are available.
➣
Text/Mix
P.Size
Info.
Sleep Perfect Focus
The picture size can not be changed in the PIP mode.
Wide
Sets to 16:9 wide mode.
Panorama
Use this mode for the wide aspect ratio of a panoramic picture.
DVD
Magnifies the picture size and moves the magnified picture up. You can also move the picture
pressing the ▼ or ▲ button.
Zoom
Magnifies the picture size. You can also move the picture pressing the ▼ or ▲ button.
Normal
Sets to 4:3 normal mode.
Cinema
Automatically expanding the broadcasting signal to appropriate picture. The margins appear
grayed.
It is possible to be a little difference to perform a gray letterbox by the specification of the
DVD or Video cassette.
➣
Wide (16:9) Model
Wide
Panorama
DVD
Cinema
Normal (4:3)
DVD
Zoom
Zoom
Normal (4:3) Model
Normal
Cinema
27
Changing the Sound Standard
ENG
You can select the type of special sound effect to be used when
watching a given broadcast.
SOUND
MODE
CUSTOM
œ
EQUALIZER
√
AUTO VOLUME
: OFF
MELODY
: ON
VIRTUAL SURROUND
: OFF
SELECT
ADJUST
√
1
Result:
2
EXIT
SELECT
√
STANDARD
EQUALIZER
AUTO VOLUME
MELODY
VIRTUAL SURROUND
√
: OFF
: ON
: OFF
ADJUST
P.STD
S.STD
Mute
S.Mode
Still
VOL
P
28
4
The options available in the SOUND group are
displayed.
button.
The MODE is selected.
Select the required sound effect by pressing the ➛ or ❿ button
repeatedly.
Result:
The following sound effects are available:
CUSTOM - STANDARD - MUSIC - SPEECH - MOVIE.
EXIT
TV
Surround
Press the
Result:
SOUND
œ
The main menu is displayed.
Press the ▼ or ▲ button to select SOUND.
Result:
3
MODE
Press the MENU button.
➣
You can also set these options simply by pressing the
S.STD (Sound Standard) button.
Adjusting the Sound Settings
ENG
The sound settings can be adjusted to suit your personal preferences.
SOUND
1
Press the MENU button.
Result:
2
The main menu is displayed.
Press the ▼ or ▲ button to select SOUND.
Result:
The options available in the SOUND group are
displayed.
3
Press the
4
Press the ▼ or ▲ button to select EQUALIZER. Press the
button.
CUSTOM
MODE
œ
EQUALIZER
√
AUTO VOLUME
: OFF
MELODY
: ON
VIRTUAL SURROUND
: OFF
SELECT
ENTER
EXIT
button.
EQUALIZER
R
Result:
5
The options available in the EQUALIZER group are
displayed.
L
Select the option to be adjusted by pressing the ➛ or ❿ button.
Press the ▼ or ▲ button to reach the required setting.
100 300
ADJUST
➣
MOVE
If you make any changes to these settings, the sound
standard is automatically switched to CUSTOM.
29
1K
3K
10K
EXIT
√
Setting the Dolby Pro Logic (depending on the model)
ENG
You can enjoy Dolby Pro Logic surround effect fully with only
surround speakers are connected to TV.
Rear of the TV
This allows various modes for the main, center and rear speakers to
be selected.
Surround Mode
Input Signal
Main
Option
SOUND
MODE
œ
√
: OFF
: ON
EQUALIZER
AUTO VOLUME
MELODY
DOLBY PRO LOGIC
SELECT
√
CUSTOM
ENTER
SELECT
œ
Stereo
Mono
✔
PHANTOM
Stereo
Mono
✔
✔
WIDE
Stereo
Mono
✔
OFF
Stereo
Mono
✔
✔
√
ADJUST
EXIT
✔
✔
✔
✔
✔
✔ ; Sound
1
Press the MENU button.
The main menu is displayed.
Result:
2
Press the ▼ or ▲ button to select SOUND.
The options available in the SOUND group are
Result:
displayed.
3
Press the
4
Press the ▼ or ▲ button to select DOLBY PRO LOGIC. Press the
button.
The options available in the DOLBY PRO LOGIC group
Result:
are displayed with the MODE selected.
5
Select the required mode (OFF, NORMAL, PHANTOM, WIDE) by
pressing the ➛ or ❿ button repeatedly.
EXIT
OFF
✔
✔
Rear
➢
√
DOLBY PRO LOGIC
MODE
NORMAL
Speakers
Centre
button.
DOLBY PRO LOGIC
NORMAL
MODE
œ
CENTER
: 0
REAR
: 0
DELAY
: 20 ms
TEST TONE : OFF
CONNECT SPEAKER
SELECT
ADJUST
√
The following Dolby settings can be adjusted to suit your personal
preferences.
◆ Volume of the centre and rear speakers
◆ Prologic delay time for the rear speakers (between
15 and 30 ms)
EXIT
◆ Activation/deactivation of the test tone to simulate the
volume on each speaker
DOLBY PRO LOGIC
NORMAL
MODE
œ
CENTER
: 0
REAR
: 0
DELAY
: 20 ms
TEST TONE : OFF
CONNECT SPEAKER
SELECT
ADJUST
30
√
5
EXIT
To...
Press the...
Change a setting
▼ or ▲ button.
Change the option
➛ or ❿ button.
Extra Sound Settings
ENG
◆ AUTO VOLUME
Each broadcasting station has its own signal conditions, and
so it is not easy for you to adjust the volume every time the
channel is changed. This feature lets you automatically adjust
the volume of the desired channel by lowering the sound
output when the modulation signal is high or by raising the
sound output when the modulation signal is low.
◆ MELODY
SOUND
CUSTOM
MODE
œ
EQUALIZER
√
AUTO VOLUME
: ON
MELODY
: ON
VIRTUAL SURROUND
: OFF
SELECT
ADJUST
√
EXIT
You can hear clear melody sound when the television is
powered on or off.
◆ VIRTUAL SURROUND (Option)
This feature converts a monaural sound signal into two
identical left and right channels. Once the VIRTUAL DOLBY
is set to ON or OFF, the setting applies to the sound effects
such as STANDARD, MUSIC, MOVIE, and SPEECH.
SOUND
CUSTOM
MODE
œ
EQUALIZER
√
AUTO VOLUME
: OFF
MELODY
: ON
VIRTUAL SURROUND
: OFF
SELECT
1
EXIT
Press the MENU button.
Result:
2
ADJUST
√
The main menu is displayed.
Press the ▼ or ▲ button to select SOUND.
Result:
The options available in the SOUND group are
displayed.
3
Press the
4
Select the required option (AUTO VOLUME, MELODY, or VIRTUAL
SURROUND) by pressing the ▼ or ▲ button.
5
To activate each feature, select ON by pressing the ➛ or ❿
button.
SOUND
MODE
CUSTOM
œ
EQUALIZER
√
AUTO VOLUME
: OFF
MELODY
: ON
VIRTUAL SURROUND
: ON
button.
SELECT
➣
ADJUST
Manufactured under license from Dolby Laboratories.
“Dolby’ and the double-D symbol
are trademarks
of Dolby Laboratories.
31
EXIT
√
Selecting the Sound Mode (depending on the model)
ENG
TV
P.STD
S.STD
Mute
S.Mode
Still
On-screen indication
Regular broadcast
(Standard audio)
MONO (Normal use)
Regular +
NICAM Mono
MONO ↔ MONO
NICAM
(Normal)
NICAM Stereo
STEREO ↔ MONO
NICAM
(Normal)
NICAM Dual-I/II
Dual-I → Dual-II → MONO
NICAM NICAM (Normal)
→
NICAM
Stereo
Type of broadcast
A2
Stereo
Regular broadcast
(Standard audio)
MONO (Normal use)
Bilingual or Dual-I/II
DUAL-I ↔ DUAL-II
Stereo
➣
→
Surround
The “S.Mode” button displays/controls the processing and output
of the audio signal. When power is switched on, the mode is
automatically preset to either “Dual-I ” or “Stereo”, depending on
the current transmission.
STEREO ↔ MONO
(Forced mono)
◆ If the receiving conditions deteriorate, listening will be
easier if the mode is set to the MONO.
◆ If the stereo signal is weak and an automatic switching
occurs, then switch to the MONO.
◆ When receiving a mono sound in the AV mode, connect
to the “AUDIO-L” input connector on the panel (front or
side). If the mono sound comes out only from left
speaker, press the S.Mode button.
32
Setting the Sleep Timer
ENG
You can select a time period of between 30 and 180 minutes after
the television automatically switches to Standby mode by pressing
the “SLEEP” button.
Display
1
Press the Sleep button on the remote control.
Result:
2
If the sleep timer is not yet set, OFF is displayed.
If the sleep timer is already set, the screen displays
the remaining time and then before the television will
be placed in standby mode.
Text/Mix
Info.
Sleep Perfect Focus
PIP
ON
Scan
Swap
Press the Sleep button repeatedly and cycle through the preset
time intervals (30, 60, 90, 120, 150, 180).
Result:
3
P.Size
The television automatically switches to standby mode
when the timer reaches 0.
To cancel the sleep timer feature, press the Sleep button
repeatedly and select OFF.
33
Locate
Setting and Displaying the Current Time
ENG
FUNCTION
LANGUAGE
TIME
➣
: ENGLISH
√
√
: ON
CONVERGENCE
BLUE SCREEN
PLUG & PLAY
DEMONSTRATION
SELECT
You can set the television’s clock so that the current time is displayed
by pressing the “DISPLAY” button. You must also set the time if you
wish to use the automatic on or off timers.
√
√
ENTER
1
When pressing the POWER ( I ) button on the front of the
television, the clock setting will be reset.
Press the MENU button.
EXIT
Result:
2
SELECT
: -- : -- AM
: OFF
ADJUST
Press the
4
Press the ▼ or ▲ button to select TIME. Press the
Result:
EXIT
: 11 : 18 AM
: OFF
ADJUST
EXIT
The options available in the FUNCTION group are
displayed.
3
button.
Press the ➛ or ❿button to move to the hour or minute.
Set the hour or minute by pressing the ▼ or ▲ button.
6
When you have finished, press the TV button to exit.
7
To...
Text/Mix
P.Size
Info.
Sleep Perfect Focus
34
Press the “DISPLAY” button...
display the channel information
Once.
display the current time
Twice.
remove the display
Display
button.
The options available in the TIME group are displayed
with Clock is selected.
5
TIME
CLOCK
TIMER
SELECT
Press the ▼ or ▲ button to select FUNCTION.
Result:
TIME
CLOCK
TIMER
The main menu is displayed.
Three times.
Switching the Television On and Off Automatically
ENG
You can set the On/Off timers so that the television will:
◆ Switch on automatically and tune to the channel of your
choice at the time you select
◆ Switch off automatically at the time you select
➣
1
The first step is to set the television’s clock (refer to
“Setting and Displaying the Current Time” on the
previous page). If you have not yet set the clock,
the message SET THE CLOCK FIRST is displayed.
√
√
: ON
CONVERGENCE
BLUE SCREEN
PLUG & PLAY
DEMONSTRATION
SELECT
√
√
ENTER
EXIT
TIME
The main menu is displayed.
CLOCK
TIMER
: 11 : 19 AM
: OFF
Press the ▼ or ▲ button to select FUNCTION.
Result:
The options available in the FUNCTION group are
displayed.
3
Press the
4
Press the ▼ or ▲ button to select TIME. Press the
Result:
ADJUST
6
Press the ➛ or ❿ button to set ON
TIME
CLOCK
TIMER
ON TIME
OFF TIME
:
:
:
:
11 : 19 AM
ON
-- : -- AM
-- : -- AM
The ON TIME and OFF TIME are displayed.
Press the ▼ or ▲ button to select ON TIME. Set the time at which
you wish the television to be switched on automatically.
SELECT
ADJUST
◆ Press the ➛ or ❿ button to move to the hour or minute.
Set the hour or minute by pressing the ▼ or ▲ button.
8
Press the ▼ or ▲ button to select OFF TIME. In the same above,
set the time at which you wish the television to be switched off
automatically.
➣
EXIT
button.
The options available in the TIME group are displayed.
Press the ▼ or ▲ button to select TIMER.
Result:
SELECT
button.
5
7
: ENGLISH
Press the MENU button.
Result:
2
FUNCTION
LANGUAGE
TIME
◆ When leave the television in Standby mode...
- During Timer Off, the LED (Stand-by & Timer indicator)
lights up Green.
- During Timer On, the LED lights up Orange.
◆ When switching the television On during Timer On,
the LED lights up Red.
EXIT
TIME
CLOCK
TIMER
ON TIME
OFF TIME
SELECT
:
:
:
:
11 : 19 AM
ON
06 : 00 AM
-- : -- AM
ADJUST
EXIT
TIME
CLOCK
TIMER
ON TIME
OFF TIME
SELECT
:
:
:
:
11 : 19 AM
ON
06 : 00 AM
23 : 30 AM
ADJUST
35
EXIT
Viewing the Picture In Picture (PIP)
ENG
You can display a sub picture within the main picture of TV program
or external A/V devices such as VCR or DVD. In this way you can
watch TV program or monitor the video input from any connected
devices while watching TV or other video input.
PIP
PIP
: OFF
1
Press the MENU button.
Result:
SELECT
ADJUST
EXIT
2
Press the ▼ or ▲ button to select PIP. Press the
3
Press the ➛ or ❿ button again to set ON.
Result:
PIP
PIP
SOURCE
PROG.NO.
SIZE
:
:
:
:
ON
TV
P 1
LARGE
4
ADJUST
EXIT
5
SELECT
:
:
:
:
ON
TV
P 1
LARGE
ADJUST
EXIT
SELECT
:
:
:
:
ON
TV
P 1
LARGE
ADJUST
EXIT
PIP
PIP
SOURCE
PROG.NO.
SIZE
SELECT
:
:
:
:
ADJUST
36
ON
TV
P 1
LARGE
EXIT
The sources are displayed in the following order:
TV - AV1 - AV2 - AV3 - AV4 - S-VHS1 - S-VHS2.
When the source of the sub picture (SELECT) is set to TV,
you can select the channel of sub picture.
Press the ▼ or ▲ button to select SIZE. Select a size of the sub
picture by pressing the ➛ or ❿ button.
The sizes are displayed in the following order
Result:
(depending on the model):
◆ LARGE - SMALL - MULTI - 3 PIP.
◆ DOUBLE - LARGE - SMALL - MULTI - 3 PIP.
➣◆
PIP
PIP
SOURCE
PROG.NO.
SIZE
6
The options available in the PIP group are displayed.
Press the ▼ or ▲ button to select PROG.NO.. If you watching TV
program, select the channel that you want to view through the
sub picture by pressing the ➛ or ❿ button.
➣
PIP
PIP
SOURCE
PROG.NO.
SIZE
button.
Press the ▼ or ▲ button to select SELECT. Find a source of the
sub picture by pressing the ➛ or ❿ button.
Result:
SELECT
The main menu is displayed.
MULTI : You can view up to 12 memorized channels on
the sub picture spontaneously.
◆ On the MULTI or 3 PIP mode, it is impossible to execute
swap and locate.
Viewing the Picture In Picture (PIP)
ENG
☛
Easy functions of remote control
Buttons
Feature
PIP ON
Used to activate or deactivate the PIP function
directly.
Scan
Used to scan every memorized channel in order.
To stop scanning, press it again.
Swap
Used to interchange the main picture and the
sub picture.
the main picture is in the Video mode
➣ When
and the sub picture is in the TV mode, you
Display
P.Size
Text/Mix
Info.
Sleep Perfect Focus
PIP
ON
Scan
Swap
might not hear the sound of main picture
when pressing the Swap button after
changing the sub picture channel. At this
time, reselect the channel of main picture.
Locate
Used to move the sub picture counterclockwise.
37
Locate
Teletext Feature
ENG
Most television channels provide written information services via
teletext. Information provided includes:
◆ Television programme times
◆ News bulletins and weather forecasts
◆ Sports results
◆ Travel information
This information is divided into numbered pages (see diagram).
Part
Contents
A
Selected page number.
B
Broadcasting channel identity.
C
Current page number or search indications.
D
Date and time.
E
Text.
F
Status information.
FASTEXT information.
➣
Teletext information is often divided between several
pages displayed in sequence, which can be accessed by:
◆ Entering the page number
◆ Selecting a title in a list
◆ Selecting a coloured heading (FASTEXT system)
Displaying the Teletext Information
You can display Teletext information at any time on your television.
Teletext information to be displayed correctly,
☛ For
channel reception must be stable; otherwise:
TV
Surround
P.STD
S.STD
◆ Information may be missing
S.Mode
◆ Some pages may not be displayed
Mute
VOL
Still
1
Select the channel providing the Teletext service using the P
or P
button.
Video
2
Press the Text/Mix button to activate the teletext mode.
The contents page is displayed. It can be redisplayed
Result:
at any time by pressing the
(index) button.
3
If you wish to display the actual broadcast at the same time as
the teletext page, press the Text/Mix button again.
4
Press the “
P
Menu
Text/Mix
Info.
Sleep Perfect Focus
PIP
ON
Scan
Swap
38
Locate
TV” button again to exit from the teletext display.
Selecting Display Options
ENG
When you have displayed a Teletext page, you can select various
options to suit your requirements.
To display...
Press the...
◆ Both teletext information and
the normal broadcast
Text/Mix twice
Surround
P.STD
S.STD
Mute
Still
VOL
P
Menu
◆ Hidden text
(answers to quiz games, for example)
(reveal)
◆ The normal screen
(reveal) again
◆ A secondary page,
by entering its 4-digit number
(sub-page)
◆ The broadcast when searching for a page
(cancel)
◆ The next page
(page up)
◆ The previous page
(page down)
◆ Double-size letters in the:
• Upper half of the screen
• Lower half of the screen
(size)
• Once
• Twice
◆ Normal screen
• Three times
S.Mode
Video
Display
P.Size
Text/Mix
Info.
Sleep Perfect Focus
PIP
ON
Scan
Swap
39
Locate
Selecting a Teletext Page
ENG
You can enter the page number directly by pressing the numeric
buttons on the remote control.
1
Enter the three-digit page number given in the content by
pressing the corresponding numeric buttons.
Result:
TV
Surround
P.STD
S.STD
Mute
S.Mode
Still
VOL
2
If the FASTEXT system is used by the broadcasting company,
the different topics covered on a Teletext page are colour-coded
and can be selected by pressing the coloured buttons on the
remote control.
Press the coloured button corresponding to the topic that you wish
to select; the available topics are given on the status line.
Result:
The page is displayed with other colored information
that can be selected in the same way.
3
To display the previous or next page, press the corresponding
coloured button.
4
To display the subpage, see the following steps.
P
Menu
Video
Text/Mix
Info.
Sleep Perfect Focus
PIP
ON
Scan
Swap
Locate
The current page counter is incremented and the
page is then displayed. If the selected page is linked
with several secondary pages, the secondary pages
are displayed in sequence. To freeze the display on a
given page, press the
(hold). Press the it again to
resume.
◆ Press the
(sub-page) button.
Result:
The available subpages appear.
◆ Enter its 4-digit number by numeric button.
40
Storing Teletext Pages
ENG
You can store up to four teletext pages to display them later at
leisure.
1
Select the LIST mode using the
Result:
➣
button.
Four 3-digit numbers are displayed in different
colours.
The
button is used to switch between the LIST and
FLOF modes.
TV
Surround
2
Press the coloured button corresponding to the page that will be
replaced.
3
Enter the new page number using the numeric buttons.
4
Repeat steps 2 and 3 for each page to be stored, using a
different coloured button each time.
5
Press the
P.STD
S.STD
Mute
S.Mode
Still
VOL
P
Menu
Video
(store) button until the corresponding blocks blink.
41
Connecting to the External Input/Outputs
ENG
Rear of the TV
VIDEO
L - AUDIO - R
MONITOR
OUT
VCR
I AV3
N
P
U
T AV2
②
Decoder /
Video game device
①
③
Video disc player
AV1(RGB IN)
or
Satellite receiver
or
➃
➢
AV1 is used for the equipment with an RGB output,
such as video game devices or video disc players.
① This end can be fitted with:
◆ A SCART connector
◆ An S-Video connector and two audio RCA connectors (L+R); AV2
◆ Three RCA connectors (VIDEO + AUDIO-L and R)
② If you have a second VCR and wish to copy cassette tape, connect the source VCR to AV2 and the
target VCR to AV3 so that you can redirect the signal from AV2 to AV3.
③ If you have a decoder, connect the decoder to the VCR and the VCR to the television.
➃ When you wish to record a programme, connect the receiver to AV2 and the VCR to AV3 so that you can
redirect the signal from AV2 to AV3.
☛
Whenever you connect an audio or video system to your
television, ensure that all elements are switched off.
Refer to the documentation supplied with your equipment
for detailed connection instructions and associated safety
precautions.
42
Connecting to the DVD Input
ENG
➢
The DVD RCA connectors are used for equipment with a DVD output.
Rear of the TV
DVD
Y
Pb
DVD
Pr
A L
U
D
I
O R
Connecting to the Audio Output
➢
The AUDIO OUT RCA connectors are used for equipment, such as an
audio system (to take full advantage of the Surround sound effect).
Rear of the TV
Audio system
A
U
L
D
I
O
R O
U
T
43
Connecting to the RCA Input (depending on the model)
ENG
➢
The RCA (VIDEO + AUDIO-L and R) connectors are used for the equipment, such as camcorders,
video disc players, and some video game devices.
Front of the TV
Camcorder
Video game device
Side of the TV
Video disc player
Connecting to the S-Video Input (depending on the model)
Front of the TV
➢
The S-VIDEO and RCA (AUDIO-L+R) connectors are
used for equipment with an S-Video output, such as a
camcorder or VCR.
Side of the TV
①
and
Camcorder
VCR
Rear of the TV
S-VIDEO1
① To play pictures and sound, both the S-VIDEO and RCA
connectors must be used.
44
Connecting Additional Speakers (depending on the model)
ENG
To take advantage of the surround sound system,
connect additional speakers.
Rear of the TV
The speaker terminals are located on the rear of
the television:
◆ Two for the left-hand surround speaker
(marked L)
◆ Two for the right-hand surround speaker
(marked R)
◆ Two for the center speaker (marked C) ;
Option
➢
To improve the quality of the sound, connect the:
◆ Red wire to the red terminal
◆ Black wire to the black terminal
Viewing Pictures From External Sources
Once you have connected up your various audio and video systems,
you can view different sources by selecting the appropriate input.
TV
Surround
1
Check that all the necessary connections have been made.
2
Switch your television on, then press the VIDEO button
repeatedly.
Result:
➣
➣
The input sources are displayed in the following
order:
TV - AV1 - AV2 - AV3 - AV4 - S-VHS1 - S-VHS2 - DVD.
P.STD
S.STD
Mute
S.Mode
Still
VOL
P
Menu
Video
Depending on the source selected, the pictures may appear
automatically.
To watch television programmes again, press the TV
button and select the number of the channel required.
45
Programming the Remote Control for Other Components
ENG
This TV’s remote control can operate almost any VCR, Cable box,
or DVD, in addition to controlling the TV.
➣
Power
TV
VCR
Cable
DVD
The remote control might not be compatible with the TV
manufactured by another company.
SET
1
Turn off your VCR, Cable box, or DVD.
2
Press the appropriate button among the component selection
buttons to activate another component (TV, VCR, Cable, DVD).
Example: If you want to program the remote control to operate
your VCR, press the VCR button on the remote
control.
3
Press the SET button.
4
Use the numeric buttons to enter the code by manufacturer. Each
code must be three digits long.
Example: To enter the code “6”, press 0, 0, and 6.
To enter the code “76”, press 0, 7, and 6.
➣
5
Press the Power ( ) button on the remote control. The
component you select should turn on. If it turns on, your remote
control is now set correctly.
➣
6
See the remote control code tables to find the appropriate
code for your particular component. If more than one code
is listed, try each one separately until you find the one that
works.
If it does not turn on, repeat steps above, but try one of the
other codes listed for the brand of particular yours. If no
other codes are listed, try each code, “000” through “089”
for VCR/DVD and “000” through “077” for Cable box.
Once your remote control is set up, press the SELECT button any
time you want to use the remote to operate your Cable box, VCR
or DVD.
➣
◆ When your remote control is in the VCR, Cable, or DVD
mode, the volume buttons still control your TV’s volume.
◆ When your remote control is in the TV or Cable mode,
the VCR or DVD control buttons (PLAY, PAUSE, etc.)
still operate your VCR or DVD.
46
Programming the Remote Control for Other Components
ENG
TV Remote Control Codes
A-Mark
Admiral
Akai
Anam
Aoc
88, 37, 90
MTC
26, 15, 6, 49, 93, 20, 8, 75
55
NEC
25, 75, 20, 8, 6, 5, 1, 1
20, 6
Nikei
50
Onking
50
Onwa
50
37, 47, 64, 41, 50
6, 37, 20, 56
Bell & Howell
67
Optonica
Broksonic
68
Panasonic
Candle
6, 12, 20, 46, 50
Penney
69
64, 72, 58, 82
61, 6, 49, 66, 18, 90, 50, 77, 25
45
Philco
1, 8, 88, 61, 6, 90, 50, 12, 98, 92, 100, 82, 20
Citizen
20, 46, 6, 50, 12, 90, 45, 9, 10
Philips
88, 1, 61, 6, 90, 12, 98, 92, 82, 20, 5, 57
Classic
50
Pioneer
65, 26
6
Portland
88, 6, 90
Centrion
Concerto
Contec
Coronado
Craig
Croslex
Crown
Curtis-Mathes
CXC
Daewoo
50, 78, 83, 81
Proton
1, 31, 6, 90, 77, 78
88, 90
Quasar
72, 58
7, 49, 50
Radio Shack
30
RCA
50
Realistic
1, 6, 20, 90, 17, 31
50
88, 1, 93, 31, 32, 33, 38, 52, 2, 3, 92, 34,
Sampo
Samsung
Sanyo
50, 92, 25, 90
61, 6, 71, 66, 87, 20, 90, 1, 62
8, 49, 50, 25
1, 20, 90, 6, 19, 26, 49
88, 0, 61, 28, 44, 29, 81, 48, 49, 90, 92, 51
89, 80, 62, 78, 13, 14
46, 50, 35, 36, 4, 5, 6, 8
Scott
1, 50, 19, 90, 6
Daytron
1, 6, 20
Sears
88, 61, 6, 8, 90, 91, 89, 80, 15, 19
Dynasty
50
Sharp
88, 90, 85, 24, 25, 69
Emerson
88, 1, 90, 50, 83, 19, 30, 81, 20, 6, 25, 55,
23, 36
Fisher
8, 80, 61, 15, 125
Funai
50, 19, 69, 6
General Electric
Goldstar
1, 61, 72, 50, 58, 17, 18, 6, 49, 19, 90
88, 27, 1, 37, 10, 11, 42, 90, 39, 40, 92, 99
Signature
Soundesign
Sylvania
Symphonic
88, 6, 90, 71, 77, 70, 21, 22, 23, 25
82
Tatung
82
Techwood
JVC
91, 92, 17, 20
60, 16, 128, 129
Kloss
92
KMC
88, 90, 13
KTV
88, 90, 50, 61, 20
1, 50, 12, 6, 19
37
SSS
Infinity
JC Penney
77, 74
Spectricon
Hitachi
JBL
84, 6, 114
Sony
Teknika
6, 50
1, 61, 6, 12, 98, 92, 20, 100, 82
2, 6, 90, 12, 20
72, 69
6, 59
88, 46, 6, 90, 50, 12, 19, 94, 84
Telefunken
96, 97
Telerent
84
TMK
1, 6, 90
47
Programming the Remote Control for Other Components
ENG
VCR Remote Control Codes
Admiral
15, 88
Aiwa
24
Akai
26, 31, 32
Audio Dynamics
Bell & Howell
Broksonic
22, 25
Multitech
NEC
Optimus
11
Panasonic
19
Pentax
16, 18 ,22, 54, 55, 61
Candle
MTC
Pentex Research+
16, 24
16, 24, 40, 41
11, 23, 25, 39, 55, 70, 73
15
17, 62, 84, 86
14, 44
55
Canon
17, 62
Philco
17, 38, 62, 65
Citizen
16, 18, 22, 54, 55, 61
Philips
17
Colortyme
Craig
Curtis-Mathes
Daewoo
DB
23
Pioneer
14, 25, 42, 59
16, 21
Portland
53, 54, 61
9, 16, 17, 23, 24, 55, 62, 73, 76
Proscan
9
3, 4, 5, 6, 7, 8, 22, 54, 85
Quartz
11
23, 25
Quasar
17, 53
Dimensia
9
Dynatech
24
RCA
36
Samsung
Electrohome
Emerson
Fisher
Funai
General Electric
17, 18, 19, 22, 24, 29, 32, 36, 43, 50, 51,
Sansui
56, 58, 66, 71, 74, 76, 77, 79
Sanyo
Harman Kardon
Instant Replay
JC Penney
Sears
11, 14, 18, 21, 27, 28, 44, 52, 57
Sharp
15, 36, 48, 54
Shintom
26, 35, 40, 64
23
17
11, 14, 16, 17, 23, 25, 39, 44, 60, 62
82
KLH
1, 2, 7
LG
11, 21
24
11, 23, 25, 39, 55
Kenwood
25
9, 16, 17, 41, 62
11, 17, 23, 25, 39, 55
JCL
0, 16, 22, 31, 41, 51
22, 50, 58, 77
14, 24, 44, 45
Hitachi
9, 14, 16, 17, 37, 44, 46, 63, 78
Scott
18, 23, 55, 69
Goldstar
11, 15, 17, 18, 21, 24, 28, 36, 52, 62
11, 21, 27, 28, 52, 57, 67
16
Go Video
Radio Shack/Realistic
Signature
Sony
Sylvania
Symphonic
Tandy
Tatung
Teac
Technics
Teknika
24
26, 35, 47
17, 24, 38, 62, 65
24
11, 24
39
24, 39, 78
17
17, 18, 24, 30
Lloyd
24
TMK
Logik
40
Toshiba
14, 22, 28, 57, 58
LXI
24
Toshiko
18
Magnavox
17, 38, 62, 65
11, 17, 23, 25, 38, 39, 55, 70
Marantz
48
Totevision
76
16,18
Programming the Remote Control for Other Components
ENG
Cable Box (CATV) Remote Control Codes
Anvision
15, 16
Pioneer
Cable Star
15, 16
Randtek
26, 28, 52
15, 16
DaeHan
5
RCA
8, 35, 74
DaeRyung
3
Regal
11, 20, 21
Dongkuk
4
Regency
Eagle
Eastern International
General Instrument
GI
Hamlim
15, 16
SAEWOO
7
20
Samsung
0, 11, 30, 52, 71, 72
54
Signature
54
Spruce
35
Starcom
54
12, 13, 23, 31, 32, 33, 38, 44, 75, 76, 77
11, 12, 20, 21, 42, 56
Hitachi
45, 51, 54
Jerrold
12, 13, 23, 31, 32, 33, 38, 44, 54, 70, 73
LG
Macom
Magnavox
Nawoo
10, 41
6
45, 51
15, 16, 27, 29, 34, 36, 37, 40, 41, 48, 49
1
Stargate2000
66
Sylvania
19, 67
TaePyungYang
2
Texscan
Tocom
19, 67
25, 29, 57, 58, 63
Unika
39, 40, 49
NSC
17
Universal
59, 60
Oak
24, 46
Viewstar
15, 16, 27, 29, 34, 36, 37, 40, 41, 48, 49
Osk Sigma
24
Panasonic
11, 35, 47, 69
Philips
Warner Amex
Zenith
52
22, 50, 65, 69
15, 16, 27, 29, 34, 36, 37, 40, 41, 48, 49
DVD Remote Control Codes
Philips
7
ProScan
8
Sony
4
RCA
8
Samsung
0
Toshiba
2
Panasonic
6
Sharp
5
LG
1
CurtisMathes
9
JVC
3
49
SCART Connector Wiring (AV1)
ENG
If you wish to connect other equipment via the SCART connectors on your television, contact your
dealer or a qualified technician to wire the A/V cable as illustrated below.
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
50
Signal
Audio output R
Audio input R
Audio output L
Audio chassis return
Video chassis return (RGB blue)
Audio input L
RGB blue input
Switching voltage
Video chassis return (RGB green)
RGB green input
Video chassis return (RGB red)
RGB red input
Blanking signal (RGB switching)
Video chassis return
Blanking signal ground
Video output
Video input
Screening/chassis return
Troubleshooting: Before Contacting Service Personnel
ENG
Before contacting Samsung after-sales service, perform the following simple checks.
If you cannot solve the problem using the instructions below, note the model and serial number of the
television and contact your local dealer.
No sound or picture
◆ Check that the mains lead has been connected to a wall socket.
◆ Check that you have pressed the POWER ( I ) button and the
Power ( ) button.
◆ Check the picture contrast and brightness settings.
◆ Check the volume.
Normal picture but no sound
◆ Check the volume.
◆ Check whether the volume Mute button on the remote control has
been pressed.
No picture or black and white picture
◆ Adjust the colour settings.
◆ Check that the broadcast system selected is correct.
Sound and picture interference
◆ Try to identify the electrical appliance that is affecting the television,
then move it further away.
◆ Plug your television into a different mains socket.
Blurred or snowy picture,
distorted sound
◆ Check the direction, location and connections of your aerial.
This interference is often occurs to the use of an indoor aerial.
Remote control malfunctions
◆ Replace the remote control batteries.
◆ Clean the upper edge of the remote control (transmission window).
◆ Check the battery terminals.
51
- AFTER SALES SERVICE
- Do not hesitate to contact your retailer or service agent
if a change in the performance of your product indicates
that a faulty condition may be present.
ELECTRONICS
BP68-00027B-00 (ENG)
Download PDF