Samsung | PS50B650S1R | Samsung PS50B650S1R User Manual

Plasma TV
user manual
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service, please register
your product at
www.samsung.com/register
Model
BN68-01939A-Eng.indd 1
Serial No.
2009-04-15 오후 2:54:30
User Instructions

Screen Image retention
Do not display a still image (such as on a video game or when hooking up a PC to this PDP) on the plasma monitor panel for more
than 2 hours as it can cause screen image retention. This image retention is also known as “screen burn”. To avoid such image
retention, reduce the degree of brightness and contrast of the screen when displaying a still image.

Height
The PDP can normally operate only under 2000m in height. It might abnormally function at a place over 2000m in height so do not
install and operate there.

Heat on the top of the PDP TV
The top side of the product may be hot after long period of use as heat dissipates from the panel through the vent hole in the upper
part of the product. This is normal and does not indicate any defect or operation failure of the product. However, children should be
prevented from touching the upper part of the product.

The product is making a ‘cracking’ noise.
A ‘cracking’ noise may occur when the product contracts or expands due to a change of surrounding environment such as
temperature or humidity. This is normal and not a defect of the unit.

Cell Defects
The PDP uses a panel consisting of 2,360,000(HD-level) to 6,221,000(FHD-level)pixels which require sophisticated technology to
produce. However, there may be few bright or dark pixels on the screen. These pixels will have no impact on the performance of
the product.

Avoid operating the TV at temperatures below 5°C(41°F)

A still image displayed too long may cause permanent damage to the PDP Panel.
Watching the PDP TV in 4:3 format for a long period of time may leave traces of borders displayed on the left,
right and centre of the screen caused by the difference of light emission on the screen. Playing a DVD or a
game console may cause similar effect to the screen. Damages caused by the above effect are not covered by
the Warranty.

Afterimage on the Screen.
Displaying still images from Video games and PC for longer than a certain period of time may produce partial afterimages.
To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when displaying still images.

Warranty
- Warranty does not cover any damage caused by image retention.
- Burn-in is not covered by the warranty.

Installation
Be sure to contact an authorized service centre, when installing your set in a location with heavy dust, high or low temperatures,
high humidity, chemical substance and where it operates continually such as the airport, the train station etc. Failure to do so may
cause a serious damage to your set.
Without producing harmful VOC (Volatile Organic Compounds),
Samsung’s Eco-friendly “Crystal Design” expresses colour gradation thanks to our dual injection technology.
Contact SAMSUNG WORLDWIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG
customer care centre. (See back cover for more informations.)
© 2009 Samsung Electronics Co., Ltd. All rights reserved.
English - BN68-01939A-Eng.indd 2
2009-04-15 오후 2:54:31
Contents
Connecting and Preparing Your TV
Media Play-DLNA
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
Checking Parts........................................................................... 4
Using the Stand-Base ............................................................... 4
Assembling the Cables............................................................... 4
Viewing the Control Panel.......................................................... 5
Viewing the Connection Panel................................................... 7
Remote Control.......................................................................... 9
Installing Batteries in the Remote Control................................ 10
Using the Remote Control Backlight Buttons........................... 10
Switching On and Off............................................................... 10
Placing Your Television in Standby Mode................................. 10
Viewing the Display.................................................................. 11
Viewing the Menus................................................................... 11
Using the TOOLS Button.......................................................... 11
Plug & Play Feature................................................................. 12
Channel Control
■ Storing Channels . .................................................................. 13
■ Managing Channels................................................................. 14
Picture Control
■
■
■
■
Changing the Picture Settings.................................................. 16
Viewing the Picture in Picture (PIP)......................................... 19
Setting up the TV with your PC................................................ 19
PC Display................................................................................ 20
Sound Control
■ Changing the Sound Setting.................................................... 21
■ Selecting the Sound Mode....................................................... 22
Function Description
■
■
■
■
Configuring the Setup Menu..................................................... 23
Setting the Time....................................................................... 24
Source List / Edit Name............................................................ 24
Supported Program.................................................................. 25
Media Play
■
■
■
■
■
■
■
■
■
■
Connecting a USB Device........................................................ 26
Using the Media Play Function................................................. 27
Using and Sorting Photo List.................................................... 28
Viewing a Photo or Slide Show ............................................... 29
Using and Sorting the Music List.............................................. 31
Playing a Music ....................................................................... 32
Using and Sorting the Movie List.............................................. 33
Playing a Movie File ................................................................ 34
Picture / Music Settings Using Media Play............................... 36
Using the Setup Menu.............................................................. 36
Symbol
Press
Setting the DLNA Network........................................................ 37
Installing the DLNA Application................................................ 37
Using the DLNA Application..................................................... 39
Using the DLNA Function......................................................... 42
Content Library
■ Activating the Content Library.................................................. 43
■ Using the Content Library......................................................... 44
Network............................................................................45
■ Network Connection................................................................. 45
■ Network Setup.......................................................................... 48
Internet@TV
■
■
■
■
■
Getting Started with Internet@TV............................................ 51
Setting up Internet@TV............................................................ 51
Using the Internet@TV service................................................ 52
Troubleshooting for internet@TV............................................. 53
Help Website............................................................................ 53
Home Network Centre
■
■
■
■
Home Network Centre.............................................................. 54
Setting Up the Home Network Centre...................................... 55
Using the Message Function.................................................... 56
Using the Media Function......................................................... 57
About Anynet+
■
■
■
■
■
■
Connecting Anynet+ Devices................................................... 58
Setting Up Anynet+ ................................................................. 59
Scanning and Switching between Anynet+ Devices................ 59
Recording................................................................................. 60
Listening through a Receiver (Home theater).......................... 61
Troubleshooting for Anynet+ ................................................... 61
Recommendations for Use
■
■
■
■
■
■
■
■
Teletext Feature........................................................................ 62
Wall Mount Kit Specifications (VESA)...................................... 63
Preparing before installing Wall- Mount on the wall................. 64
How to attach the Stand-Base.................................................. 64
Securing the TV to the Wall...................................................... 65
Securing the Installation Space................................................ 65
Troubleshooting........................................................................ 66
Specifications........................................................................... 67
N
O
T
Note
One-Touch Button
TOOLS
English - BN68-01939A-Eng.indd 3
2009-04-15 오후 2:54:31
Connecting and Preparing Your TV
Checking Parts
Owner’s
Instructions
Remote Control/
AAA Batteries (2ea)
Power Cord
Holder-Ring (4ea)
(Refer to page 64)
Cover-Bottom / Screws (2ea)
PS58B680/PS63B680 only
Cover-Bottom
PS50B650 only
Warranty Card/
Safety Guide Manual
(Not available in all locations)
Screw (4ea)
(PS50B650 only)
Holder-Wire
Cable
Cloth-Clean
Program CD
Ferrite Core for Ferrite Core for
Power Cord
Headphone
(Not available in all locations)
N Ferrite Core (Power Cord, Headphone)
The ferrite cores are used to shield the cables from interference.
When connecting a cable, open the ferrite core and clip it around the cable near the plug.
Using the Stand-Base
N Two or more people should carry the PDP. Never lay the PDP on the floor
because of possible damage to the screen. Always keep the PDP upright.
N The PDP can rotate 20 degrees in right and left directions.
-20° ~ 20°
Assembling the Cables
Enclose the cables in the Holder-Wire Cable so that the cables are not visible through the transparent
stand.
English - BN68-01939A-Eng.indd 4
2009-04-15 오후 2:54:32
Viewing the Control Panel
PS50B650
Front Panel buttons
N The product colour and shape may vary depending on the model.
1 SOURCE
Toggles between all the available input sources
(TV, AV1, AV2, Component1, Component2, PC, HDMI1,
HDMI2/DVI, HDMI3, HDMI4).
N In the on-screen menu, use this button as you would use
the ENTERE button on the remote control.
2 MENU
Press to see an on-screen menu of your TV’s features.
3 + VOL Press to increase or decrease the volume. In the on-screen
menu, use the + VOL - buttons as you would use the
◄ and ► buttons on the remote control.
Touch each button to
operate.
4 < CH >
Press to change channels. In the on-screen menu, use the
< CH > buttons as you would use the ▲ and ▼ buttons on
the remote control.
5 POWER INDICATOR
Lights up when the power is on.
(POWER)
Press to turn the TV on and off.
7 REMOTE CONTROL SENSOR
Aim the remote�������������������������������������
�������������������������������������������
control towards this spot on the TV.
8 SPEAKERS
6
Continued...
English - BN68-01939A-Eng.indd 5
2009-04-15 오후 2:54:32
PS58B680/PS63B680
N The product colour and shape may vary depending on the model.
1 SOURCE
Toggles between all the available input sources
(TV, AV1, AV2, Component1, Component2, PC, HDMI1,
HDMI2/DVI, HDMI3, HDMI4, USB, DLNA).
N In the on-screen menu, use this button as you would use
the ENTERE button on the remote control.
2 MENU
Press to see an on-screen menu of your TV’s features.
3 + VOL Press to increase or decrease the volume. In the on-screen
menu, use the + VOL - buttons as you would use the
◄ and ► buttons on the remote control.
Front Panel buttons
Touch each button to operate.
4 < CH >
Press to change channels. In the on-screen menu, use the
< CH > buttons as you would use the ▲ and ▼ buttons on
the remote control.
5 POWER INDICATOR
Blinks and turns off when the power is on and lights up in
stand-by mode.
6 REMOTE CONTROL SENSOR
Aim the remote control towards this spot on the TV.
7 SPEAKERS
8 (POWER)
Touch the silver sensor below the (P) mark to turn the TV on
and off.
English - BN68-01939A-Eng.indd 6
2009-04-15 오후 2:54:33
Viewing the Connection Panel
TV Rear Panel
1
0
or
2
Cable Television
Network
or
3
4
5
6
7
9
8
N Whenever you connect an audio or video system to your set, ensure that all elements are switched off.
N When connecting an external device, match the colour of the connection terminal to the cable.
1 LAN
Connect a LAN cable to this port to connect to the Network
(SAMSUNG's Internet@TV Service).
2 POWER IN
Connect the supplied power cord.
3 AV IN 1(VIDEO / AUDIO R/L)
Video and audio inputs for external devices, such as a
camcorder or VCR.
4 PC IN(PC) / AUDIO
Connect to the video and audio output jack on your PC.
9 HDMI IN 1, 2, 3
- No additional Audio connection is needed for an HDMI to
HDMI connection.
- Whenusing an HDMI/DVI cable connection, you must use
the HDMI IN 2 jack.
N What is HDMI?
- “High Definition Multimedia interface” allows the
transmission of high definition digital video data and
multiple channels of digital audio.
- The HDMI/DVI terminal supports DVI connection to
an extended device with the appropriate cable (not
supplied). The difference between HDMI and DVI is
that the HDMI device is smaller in size, has the HDCP
(High Bandwidth Digital Copy Protection) coding feature
installed, and supports multi - channel digital audio.
5 COMPONENT IN 1, 2
Audio (AUDIO R/L) and video (Y/PB/PR) inputs for
Component.
6 HEADPHONES JACK
You can connect a set of headphones if you wish to watch a
television programme without disturbing the other people in
the room.
N Prolonged use of headphones at a high volume may
damage your hearing
7 SERVICE
Connector for service.
8 AUDIO OUT(AUDIO R/L)
Connect RCA audio signals from the TV to an external source,
such as Audio equipment.
DVI AUDIO IN
DVI audio outputs for external devices.
0 ANT IN
75Ω Coaxial connector for Aerial/Cable Network.
Supported modes for HDMI/DVI and Component
HDMI/DVI 50Hz
HDMI/DVI 60Hz
Component
480i
X
X
O
480p
X
O
O
576i
X
X
O
576p
O
X
O
720p 1080i 1080p
O
O
O
O
O
O
O
O
O
Continued...
English - BN68-01939A-Eng.indd 7
2009-04-15 오후 2:54:34
TV Side Panel
2
1
3
N The product colour and shape may vary depending on the model.
1 USB 1(HDD), USB 2
Connect a USB mass storage device to view photo files
(JPEG), play audio files (MP3) and movie files.
You can connect to SAMSUNG’s network wirelessly.
2 HDMI IN 4
Connect to the HDMI jack of a device with HDMI output.
3 AV IN 2
Video and audio inputs for external devices, such as a
camcorder or VCR.
English - BN68-01939A-Eng.indd 8
2009-04-15 오후 2:54:35
Remote Control
You can use the remote control up to a distance of about 23 feet from the TV.
N The performance of the remote control may be affected by bright light.
1 POWER button
(turns the TV on and off)
2 Selects the TV mode directly.
3 Number buttons for direct channel
access
4 Use to select on-screen menu items
5 Temporary sound switch-off
Volume increase
Volume decrease
7 Available source selection
8 Channel control button
9 Use to quickly select frequently used
functions.
0 Control the cursor in the menu
! This function enables you to view
Internet@TV.
@ Use these buttons in the Media Play,
etc.
$ Use to see information on the current
broadcast
% Use these buttons in the Anynet+ and
Media Play.
^ Press to backlight the buttons on the
remote. This function is convenient
for using at night or when the room is
dark. (Using the remote control with
the ON/OFF( ) light button set to On
will reduce the battery usage time.)
& Previous channel
6
d This function enables you to view
Content Library.
e Sound mode selection
f Picture size selection
Teletext Functions
2 Exit from the teletext display
(depending on the model)
7 Teletext mode selection (LIST/FLOF)
8 Teletext store
9 Teletext size
@ Fastext topic selection
# Teletext display/mix both
teletext information and the normal
broadcast
$ Teletext reveal
& Teletext sub page
:Teletext next page
* P
P
:Teletext previous page
( Teletext index
a Teletext hold
b Teletext cancel
Next channel
Previous channel
( Displays the main on-screen menu
) Press to switch to your favorite
channels.
a Returns to the previous menu
b Exit the on-screen menu
c This function enables you to view and
play photo, music and movie files from
an external device.
(Refer to pages 28 (Photo), 31(Music),
and 33(Movie))
*
English - BN68-01939A-Eng.indd 9
2009-04-15 오후 2:54:35
Installing Batteries in the Remote Control
1. Lift the cover at the back of the remote control upward as shown in the figure.
2. Install two AAA size batteries.
N Make sure to match the ‘+’ and ‘–’ ends of the batteries with the diagram inside
the compartment.
N Using the remote control with the ON/OFF(
the battery usage time.
) light button set to On will reduce
3. Close the cover.
N Remove the batteries and store them in a cool, dry place if you won’t be using the
remote control for a long time.
N If the remote control doesn’t work, check the following
1. Is the TV power on?
2. Are the plus and minus ends of the batteries reversed?
3. Are the batteries drained?
4. Is there a power outage or is the power cord unplugged?
5. Is there a special fluorescent light or neon sign nearby?
Using the Remote Control Backlight Buttons
Use this feature in dark surroundings and when you are unable to see the remote control buttons clearly.
1. Press the ON/OFF( ) light button
N When ON, the button backlight is turned on for a moment.
N Pressing a remote control button when the remote control is on turns the button backlight on for a moment.
Switching On and Off
The mains lead is attached to the rear of your set.
1. Plug the mains lead into an appropriate socket.
N The standby indicator lights up on your set.
2. Press the POWERP button on your set.
N You also can press the POWERP button or the TV button on the remote control to turn the TV on.
The programme that you were watching last is reselected automatically.
3. Press the numeric button (0~9) or channel up / down (< / >) button on the remote control or < CH > button on your set.
N When you switch the set on for the very first time, you will be asked to choose language in which the menus are to be displayed.
4. To switch your set off, press the POWERP button again.
Placing Your Television in Standby Mode
Your set can be placed in standby mode in order to reduce the power consumption. The standby mode can be useful when you wish to
interrupt viewing temporarily (during a meal, for example).
1. Press the POWERP button on the remote control.
N The screen is turned off and a red standby indicator appears on your set.
2. To switch your set back on, simply press the POWERP, numeric buttons (0~9), TV button or channel up / down (< / >) button
again.
N Do not leave your set in standby mode for long periods of time (when you are away on holiday, for example). It is best to unplug
the set from the mains and aerial.
English - 10
BN68-01939A-Eng.indd 10
2009-04-15 오후 2:54:36
Viewing the Display
The display identifies the current channel and the status of certain audio-video settings.
1. Press the INFO button on the remote control. The TV will display the channel, the type of
sound, and the status of certain picture and sound settings.
1 : 49 Thu 1 Jan
ATV
13-1
N Press the INFO button once more or wait approximately 10 seconds and it disappears
automatically.
Viewing the Menus
N The on-screen menus disappear from the screen after about one minute.
Picture
1. With the power on, press the MENU button. The main menu appears on the screen.
The menu’s left side has icons: Picture, Sound, Channel, Setup, Input, Application,
Support.
2. Press the ▲ or ▼ button to select one of the icons. Then press the ENTERE button
to access the icon’s sub-menu.
3. Press the EXIT button to exit.
Mode
:Standard
Cell Light
:4
Contrast
: 95
Brightness
: 45
Sharpness
: 50
Colour
: 50
Tint (G/R)
: G50/R50
Advanced Settings
Using the TOOLS Button
You can use the TOOLS button to select your frequently used functions quickly and easily. The Tools menu changes depending on
which external input mode you are viewing.
1. Press the TOOLS button. The Tools menu will appear.
2. Press the ▲ or ▼ button to select a menu, then press the ENTERE button.
3. Press the ▲ / ▼ / ◄ / ► / ENTERE buttons to display, change, or use the selected
items. For a more detailed description of each function, refer to the corresponding page.
• Anynet+ (HDMI-CEC), see page 59
• Picture Size, see page 17
• Picture Mode, see page 16
• Sound Mode, see page 21
• Sleep Timer, see page 24
• SRS TS HD, see page 21
• Energy Saving, see page 23
• Dual I II, see page 22
• Add to Favourite (or Delete from Favourite), see page 14
• PIP, see page 19
• Auto Adjustment, see page 19
Tools
Anynet+ (HDMI-CEC)
Picture Size :
16:9
Picture Mode :
Standard
Sound Mode :
Custom
Sleep Timer :
Off
SRS TS HD
:
Off
Energy Saving :
Off
Dual I II
:
Mono
Add to Favourite
U Move
E Enter
e Exit
English - 11
BN68-01939A-Eng.indd 11
2009-04-15 오후 2:54:36
Plug & Play Feature
When the TV is initially powered on, basic settings proceed automatically and subsequently.
N The Screen Saver is activated if there is no remote control key input for longer than 1 minute while Plug & Play is running.
N The Screen Saver is activated if there is no operating signal for longer than 15 minutes.
1. Press the POWER button on the remote control. Language menu is displayed.
2. Press the ENTERE button. Select the appropriate language by pressing the ▲
or ▼ button. Press the ENTERE button. The message Select ‘Home Use’ when
installing this TV in your home. is displayed.
3. Press the ◄ or ► button to select Store Demo or Home Use, then the ENTERE
button.
Plug & Play
Select the OSD Language.
Language
: English
►
E Enter
N We recommend setting the TV to Home Use mode for the best picture in your home environment.
N Store Demo mode is only intended for use in retail environments.
N If the unit is accidentally set to Store Demo mode and you want to return to Home Use (Standard): Press the Volume button on
the TV. When the volume OSD is displayed, press and hold the MENU button on the TV for 5 seconds.
4. Make sure that the antenna is connected to the TV. Press the ENTERE button. Area menu is displayed.
5. Press the ENTERE button.Select your country or area by pressing the ▲ or ▼ button, then press the ENTERE button. Auto
Store menu is displayed.
N To stop the search before it has finished, press the ENTERE button with Stop selected.
6. The channel search will start end automatically. After all the available channels are stored, the message Set current date and time
is displayed. Press the ENTERE button.
7. Press the ◄ or ► button to select Day, Month, Year, Hour, or Minute. Set these by pressing the ▲ or ▼ button.
N You can set the Day, Month, Year, Hour, and Minute directly by pressing the numeric buttons on the remote control.
8. The brief instruction on How to get the best performance from your new HDTV is displayed. Press the ENTERE button.
N You can change previous or next page by pressing the ◄ or ► button.
N This menu is available HD Connection Guide in the Support menu.
9. The message Enjoy your TV. is displayed.
N If you want to view the TV immediately, select the Watch TV.
N If you want to view the See Product Guide, press the ENTERE button.
If you want to reset this feature...
N If you want to change PIN number, refer to page 23.
N The Plug & Play feature is only available in the TV mode.
Setup
1. Press the MENU button to display the menu. Press the ▲ or ▼ button to select Setup,
then press the ENTERE button.
2. Press the ENTERE button again to select Plug & Play.
3. Enter your 4 digit PIN number. The default PIN number of a new TV set is ‘0-0-0-0’.
Plug & Play
Language
►
: English
Time
Game Mode
: Off
BD Wise
: Off
Network Type
: Cable
Network Setup
Child Lock
: On
English - 12
BN68-01939A-Eng.indd 12
2009-04-15 오후 2:54:36
Channel Control
Storing Channels
❑ Area
Channel
You can change the desired area.
❑ Auto Store
Scans for all channels with active broadcast stations (and availability depends on your
country) and stores them in the TV's memory.
N If you want to stop Auto Store, press the ENTERE button.
The Stop Auto Store? message will be displayed.
Select Yes by pressing the ◄ or ► button, then press the ENTEREbutton.
Area
: Asia/Europe
►
Auto Store
Manual Store
Channel List
Channel Mode : Added Ch.
Fine Tune
❑ Manual Store
Scans for a channel manually and stores it in the TV’s memory.
• Programme (Programme number to be assigned to a channel): Sets the programme number using the ▲, ▼ or number (0~9)
buttons.
• Colour System → Auto / PAL / SECAM / NTSC4.43 / NTSC 3.58: Sets the colour system value using the ▲ or ▼ button.
• Sound System → BG / DK / I / M: Sets the sound system value using the ▲ or ▼ button.
• Channel (When you know the number of the channel to be stored): Press the ▲ or ▼ button to select C (Air channel) or
S (Cable channel). Press the ► button, then press the ▲, ▼ or number (0~9) buttons to select the required number.
N You can also select the channel number directly by pressing the number (0~9) buttons.
N If there is abnormal sound or no sound, reselect the sound standard required.
• Search (When you do not know the channel numbers): Press the ▲ or ▼ button to start the search. The tuner scans the
frequency range until the first channel or the channel that you selected is received on the screen.
• Store (When you store the channel and associated programme number): Set to OK by pressing the ENTERE button.
N Channel mode
- C (Air channel mode): You can select a channel by entering the assigned number to each air broadcasting station in this
mode.
- S (Cable channel mode): You can select a channel by entering the assigned number for each cable channel in this mode.
❑ Channel Mode
When the press the P
/
button, channels will be switched within the selected channel list.
• Added Ch.: Channels will be switched within the memorized channel list.
• Favourite Ch.: Channels will be switched within the favourite channel list.
❑ Fine Tune
If the reception is clear, you do not have to fine tune the channel, as this is done automatically during the search and store
operation. If the signal is weak or distorted, you may have to fine tune the channel manually.
N Fine tuned channels that have been saved are marked with an asterisk *.
N If you do not store the fine-tuned channel in memory, adjustments are not saved.
N To reset the fine-tuning, select Reset by pressing the ▼ button and then press the ENTERE button.
English - 13
BN68-01939A-Eng.indd 13
2009-04-15 오후 2:54:37
Managing Channels
❑ Channel List
Auto Store
Manual Store
Channel
Using this menu, you can Add / Delete or set Favourite channels and use the programme
guide for digital broadcasts.
Channel List
Channel Mode N Select a channel in the All Channels, Added Channels, Favourites, or Programmed
: Added Ch.
Fine Tune
All Channels
screen by pressing the ▲ / ▼ buttons, and pressing the ENTERE button. Then you
can watch the selected channel.
• All Channels: Shows
���������������������������������������
all currently available channels.
• Added Channels: Shows
�������������������������
all added channels.
• Favourites: Shows
�����������������������������
all favourite channels.
• Programmed: Shows
��������������������������������������
all current reserved programmes.
N Using the Colour buttons with the Channel List
• Green (Zoom): Enlarges or shrinks a channel number.
• Yellow (Select): Selects multiple channel lists.
• T TOOLS(Tools): Displays the Delete (or Add), Add to Favourite (or Delete from
Favourite), Lock (or Unlock), Timer Viewing, Edit Channel Name, Sort, Select All,
Deselect All�, or Auto Store menu.
(The Options menus may differ depending on the situation.)
Zoom
6
7
C-C--
8
C--
9
10
11
12
13
19
C-C-C-C-C-C--
Select
T
Tools
N Channel Status Display Icons
♥
A channel set as a Favourite.
c
A channel selected by pressing the yellow button.
\
A locked channel.
)
A reserved programme
O Press the CH LIST button on the remote control to bring up the channel lists.
❑ Channel List Tools Menu (in All Channels / Added Channels /
Favourites)


Add / Delete
You can delete or add a channel to display the channels you want.
N All deleted channels will be shown on All Channels menu.
N A gray-coloured channel indicates the channel has been deleted.
N The Add menu only appears for deleted channels.
N You can also delete a channel to the Added Channels or Favourite menu in the
same manner.
All Channels
N Press the TOOLS button to use the tools menu.
N Option menu items may differ depending on the channel status.
Zoom
6
7
C-C--
8
C--
9
10
11
12
13
19
C-C-C-C-C-C--
Select
T
Delete
Add to Favourite
Lock
Timer Viewing
Edit Channel Name
Sort
▼
Tools
Add to Favourite / Delete from Favourite
You can set channels you watch frequently as favourites.
T Press the TOOLS button to display Tools menu.
You can also add the favourite channel by selecting Tools →
Add to Favourite (or Delete from Favourite).
N The ♥ symbol will be displayed and the channel will be set as a favourite.
N All favourite channels will be shown on Favourites menu.
O To select the Favourite channels you have set up, press the FAV.CH button on the
remote control.

Lock / Unlock
You can lock a channel so that the channel cannot be selected and viewed. This
function is available only when the Child Lock is set to On. (see page 23)
N The PIN number input screen appears. Enter your 4 digit PIN number.
N The default PIN number of a new TV set is '0-0-0-0'. You can change the PIN, by selecting Change PIN from the menu.
N The \ symbol will be displayed and the channel will be locked.
Continued...
English - 14
BN68-01939A-Eng.indd 14
2009-04-15 오후 2:54:37

Timer Viewing
If you reserve a programme you want to watch, the channel is automatically switched to the reserved channel in the Channel List;
even when you are watching another channel. To reserve a programme set the current time first. (See page 15)
N Only memorized channels can be reserved.
N You can set the Channel, Date, or Start Time directly by pressing the number buttons on the remote control.
N Reserving a programme will be shown on Programmed menu.
 Edit Channel Name
Channels can labeled so that their call letters appear whenever the channel is selected.
N The names of digital broadcasting channels are automatically assigned and cannot be labeled.

Sort
This operation allows you to change the programme numbers of the stored channels. This operation may be necessary after using
the auto store.

Select All / Deselect All
• Select All: You can select all the channels in the channel list.
• Deselect All: You can deselect all the selected channels in the channel list.
N You can perform the Add/Delete, Add to Favourite/Delete from Favourite, or Lock/Unlock function for multiple channels at
the same time. Select the required channels and press the yellow button to set all the selected channels at the same time.
N The c mark appears to the left of the selected channels.
N You can only select Deselect All when there is a selected channel.

Auto Store
N For further details on setting up options, refer to page 13.
N If a channel is locked using the Child Lock function, the PIN input window appears.
You can view, modify or delete a reservation.
N Press the TOOLS button to use the tools menu.
• Change Info: Select to change a viewing reservation.
• Cancel Schedules: Select to cancel a viewing reservation.
• Information: Select to view a viewing reservation. (You can also change the
reservation information.)
• Select All / Deselect All: Select or deselect all reserved programmes.
Programmed
❑ Channel List Tools Menu (in Programmed)
1 / 1 / 2009
Zoom
Change
Quincy,
M.EInfo
Cancel Schedules
13:59
5
18:59
2
The Equalizer
20:59
2
McMillan & Wife
21:59 2
M.Spillane’s mike Hammer
Select
T
Tools
E
Information
Select All
Information
English - 15
BN68-01939A-Eng.indd 15
2009-04-15 오후 2:54:37
Picture Control
Changing the Picture Settings
❑ Mode
Picture
You can select the type of picture which best corresponds to your viewing requirements.
• Dynamic: Selects the picture for high-definition in a bright room.
• Standard: Selects the picture for the optimum display in a normal environment.
• Eco : Selects the picture for optimum and eye-comfortable display.
• Movie: Selects the picture for viewing movies in a dark room.
T Press the TOOLS button to display Tools menu.
You can also set the picture mode by selecting Tools → Picture Mode.
Mode
: Standard
Cell Light
:4
Contrast
: 95
Brightness
: 45
Sharpness
: 50
Colour
: 50
Tint (G/R)
: G50/R50
►
Advanced Settings
❑ Cell Light / Contrast / Brightness / Sharpness / Colour / Tint (G/R)
Picture
Your television has several setting options that allow you to control the picture quality.
• Cell Light: Adjusts the pixel brightness.
• Contrast: Adjusts the contrast level of the picture.
• Brightness: Adjusts the brightness level of the picture.
• Sharpness: Adjusts the edge definition of the picture.
• Colour: Adjusts Colour saturation of the picture.
• Tint (G/R): Adjusts the Colour tint of the picture.
N Select a picture mode to be adjusted first. The adjusted values are saved for each picture mode.
N When you make changes to Cell Light, Contrast, Brightness, Sharpness, Colour or Tint (G/R), the OSD will be adjusted
accordingly.
N In Analogue TV, AV modes of the PAL system, you cannot use the Tint Function.
N In PC mode, you can only make changes to Cell Light, Contrast, and Brightness.
N Settings can be adjusted and stored for each external device you have connected to an input of the TV.
N The energy consumed during use can be significantly reduced if the level of
Colour
: 50
brightness of the picture is reduced, and then this will reduce the overall running
Tint (G/R)
: G50/R50
cost.
Advanced Settings
►
Picture Options
❑ Advanced Settings
You can adjust the detailed settings for your screen including the colour and contrast.
N Advanced Settings is available in Standard or Movie mode.
N In PC mode, you can only make changes to Dynamic Contrast, Gamma and
White Balance from among the Advanced Settings items.
Picture Reset

Black Tone ��
→� ������
Off / Dark
�������/ Darker
���������/ Darkest
�������
You can enhance the picture depth by adjusting the black colour density.

Dynamic Contrast →�
�� Off
����������
/ Low /�����������
Medium / High
����
You can adjust the screen contrast so that the optimal contrast is provided.

Gamma
You can adjust the primary colour (Red, Green, Blue) Intensity.

Colour Space
Colour Space is a colour matrix composed of red, green and blue colours. Select your favourite colour space to experience the
most natural colour.
• Auto: Automatically sets the colour range depending on the input video source.
• Native: Sets the colour range wider than the that of the input video source.
• Custom: Adjusts the colour range to suit your preference.
N Customizing the Color Space
- Adjusts the Color range to suit your preference. Color is available when Color Space is set to Custom.
- Color: Red / Green / Blue / Yellow / Cyan / Magenta
- Red / Green / Blue: You can adjust the RGB values for the selected color.
- Reset: Resets the color space to the default values
Continued...
English - 16
BN68-01939A-Eng.indd 16
2009-04-15 오후 2:54:37

White Balance
You can adjust the colour temperature for more natural picture colours.
• R-Offset / G-Offset / B-Offset / R-Gain / G-Gain / B-Gain: Changing the adjustment value will refresh the adjusted screen.
• Reset: The previously adjusted white balance will be reset to the factory defaults.

Flesh Tone
You can adjust the flesh tone to be more or less red.
N Changing the adjustment value will refresh the adjusted screen.

Edge Enhancement ��
→� ������
Off / On
��
You can emphasize object boundaries in the picture.

xvYCC → Off / On
Setting the xvYCC mode to on increases detail and colour space when watching movies from an external device (i.e. DVD player).
N xvYCC is available when the picture mode is set to Movie, and the external input is set to HDMI or Component mode.
❑ Picture Options
You can customize the additional picture settings to suit your preference.
Burn Protection from among the items in Picture Options.
Tint (G/R)
Picture
N In PC mode, you can only make changes to the Colour Tone, Size, and Screen
: G50/R50
Advanced Settings
Picture Options
►
Picture Reset

Colour Tone →�
�� Cool / Normal / Warm1 / Warm2 / Warm3
You can select the most comfortable colour tone to your eyes.
N The adjusted values are stored according to the selected Picture mode.
N Warm1, Warm2 or Warm3 is only activated when the picture mode is Movie.

Size
You can select the picture size which best corresponds to your viewing requirements.
• 16:9: Adjusts the picture size to 16:9 appropriate for DVDs or wide broadcasting.
• Wide Zoom: Magnify the size of the picture more than 4:3.
• Zoom: Magnifies the 16:9 wide picture (in the vertical direction) to fit the screen size.
• 4:3: This is the default setting for a video movie or normal broadcasting.
• Screen Fit: Use the function to see the full image without any cutoff when HDMI (720p / 1080i / 1080p)
or Component (1080i / 1080p) signals are input.
N The picture size options may vary depending on the input source.
N The items available may differ depending on the selected mode.
N In PC Mode, only 16:9 and 4:3 mode can be adjusted.
N Settings can be adjusted and stored for each external device you have connected to an input of the TV.
N Temporary image retention may occur when viewing a static image on the set for more than two hours.
N After selecting Wide Zoom mode: Press the ► button to select Position, then press the ENTERE button.
Press the ▲ or ▼ button to move the screen up / down. Then press the ENTERE button.
N After selecting Zoom mode: Press the ► button to select Position, then press the ENTERE button. Press the ▲ or ▼
button to move the picture up and down. Then press the ENTERE button. Press the ► button to select Size, then press the
ENTERE button. Press the ▲ or ▼ button to magnify or reduce the picture size in the vertical direction.
Then press the ENTERE button.
N After selecting Screen Fit in HDMI (720p / 1080i / 1080p) or Component (1080i / 1080p) mode:
Select Position by pressing the ◄ or ►button. Use the ▲, ▼, ◄ or ► button to move the picture.
N Reset: Press the ◄ or ► button to select Reset, then press the ENTERE button. You can initialize the setting.
N If you use the Screen Fit function with HDMI 720p input, 1 line will be cut at the top, bottom, left and right as in the overscan
function.
T Press the TOOLS button to display Tools menu.
You can also set the picture size by selecting Tools → Picture Size.
O You can select these options simply by pressing the P.SIZE button on the remote
control.

Digital NR →�
�� Off / Low / Medium / High / Auto
If the broadcast signal received by your TV is weak, you can activate the Digital Noise Reduction feature to help reduce any static
and ghosting that may appear on the screen.
N When the signal is weak, select one of the other options until the best picture is displayed.
N This function is not available in PC mode.
Continued...
English - 17
BN68-01939A-Eng.indd 17
2009-04-15 오후 2:54:38

HDMI Black Level →�
�� Normal / Low
You can directly select the black level on the screen to adjust the screen depth.
N This function is active only when the external input connects to HDMI (RGB signals).

1080 Full HD Motion Demo → Off / On
Samsung' new generation PDP panels deliver stunning Full HD motion clarity when viewing fast action sports, movies, and games.

Film Mode
You can optimize the picture mode for watching movies.
• Off : Turn the Film Mode function off.
• Auto1: Automatically adjusts the picture for the best quality when watching a film.
• Auto2: Automatically optimizes the video text when watching a film.
N Film mode is supported in TV, Video, Component(480i / 1080i) and HDMI(1080i).
• Cinema Smooth: Offers the ultimate cinema experience.
N This function is available when the external input connects to HDMI (1920x1080p@24Hz).

Real 100Hz Demo → Off / On
You can get a clear distinction between Real 100Hz and 50Hz, especially when watching fast moving scenes. Therefore, when
seeing slow moving scenes, you will not be able to distinguish between Real 100Hz and 50Hz. Demo 100Hz works only with 50Hz
signal. Real 100Hz demo mode is provided for shop demonstration with special pictures.

Blue Only Mode → Off / On
This function is for AV device measurement experts. This function displays the blue signal only by removing the red and green
signals from the video signal so as to provide a blue filter effect that is used to adjust the colour and tint of video equipment such as
DVD players, Home The­aters, etc.
N Blue Only Mode is available when the picture mode is set to Movie or Standard.

Screen Burn Protection
Configures the Screen Burn Protection Options to prevent and reduce pixel burn.
When an image remains in one position too long, it may cause a permanent burn on the screen.
• Pixel Shift: To reduce the possibility of screen burn, this unit is equipped with screen burn prevention technology.
This technology enables you to set picture movement up/down (Vertical) and side to side (Horizontal).
The Time setting allows you to program the time between movement of the picture in minutes.
N Set Pixel Shift to On by pressing the ▲ or ▼ button, then press the ENTERE button.
N Select the required option by pressing the ▲ or ▼ button, then press the ENTERE button.
N Available options: Horizontal, Vertical, Time.
N Optimum condition for pixel shift
Item
TV/AV/Component/HDMI/PC
Horizontal
0~2
2
Vertical
0~4
4
Time (minute)
1~4 min
2 min
N The Pixel Shift value may differ depending on the monitor size (inches) and mode.
N This function is not available in the Screen Fit mode.
• Scrolling: This function helps remove after images on the screen by moving all the pixels on the PDP according to a pattern
Use this function when there are remaining after images or symbols on the screen especially when you displayed a still image
on the screen for a long time.
• Side Grey: When you watch TV with the screen ratio of 4:3, the screen is prevented from any damage by adjusting the white
balance on both extreme left and right sides.
- Light: When you set the screen ratio to 4:3, it brightens the left and right sides.
- Dark: When you set the screen ratio to 4:3, it darkens the left and right sides.
Advanced Settings
❑ Picture Reset → Reset Picture Mode / Cancel
Picture Options
Picture
Resets all picture settings to the default values.
N Select a picture mode to be reset. The reset is performed for each picture mode.
Picture Reset
►
English - 18
BN68-01939A-Eng.indd 18
2009-04-15 오후 2:54:38
Viewing the Picture in Picture (PIP)
Setup
You can display a sub picture within the main picture of set programme or video input. In
this way, you can watch the picture of set programme or video input from any connected
equipment while watching the main picture.
Melody
: Medium
Energy Saving
: Off
PIP
►
N You may notice that the picture in the PIP window becomes slightly unnatural when you
use the main screen to view a game or karaoke.
T Press the TOOLS button to display Tools menu. You can also configure PIP
related settings by selecting Tools → PIP.
❑ PIP → Off / On
You can activate or deactivate the PIP function.
Main picture
Sub picture
Component1, Component2
HDMI 1, HDMI2/DVI, HDMI 3, HDMI 4
TV, AV1, AV2
PC
PIP
►
PIP
◄
On
Source
:
TV
Size
:
Position
:
Channel
:
ATV 1
Sound Select
:
Main

Size →
/
/
/
You can select a size of the sub-picture.

Source → TV/AV1/AV2
You can select a source of the sub-picture.
N You can select these options simply by pressing the SOURCE button on the remote control.

Position →
/
/
/
You can select a position of the sub-picture.
N In Double (
, ) mode, Position cannot be selected.

Channel
You can select a channel of the sub-picture only when the Source is set to TV.
U Move
E Enter
R Return
Setting up the TV with your PC
N Preset: Press the SOURCE button to select PC mode.
Auto Adjustment allows the PC screen of set to self-adjust to the incoming PC video
signal. The values of fine, coarse and position are adjusted automatically.
N This function does not work in DVI-HDMI mode.
T Press the TOOLS button to display Tools menu.
Picture
❑ Auto Adjustment
Brightness
: 45
Sharpness
: 50
Auto Adjustment
►
Screen Advanced Settings
Picture Options
Picture Reset
You can also set the adjustment by selecting Tools → Auto Adjustment.
❑ Screen
The purpose of picture quality adjustment is to remove or reduce picture noise. If the noise is not removed by Fine-tuning alone,
then adjust the frequency as best as possible (Coarse) and Fine-tune again. After the noise has been reduced, readjust the picture
so that it is aligned on the center of screen.

Coarse
Adjusts the frequency when vertical noise appears on the screen.

Fine
Adjusts the screen to be clearer.

PC Position
Adjust the PC’s screen positioning if it does not fit the TV screen. Press
������������������������������������������������������������
the ▲ or ▼ button to adjusting the Vertical-Position.
Press the ◄ or ► button to adjust the Horizontal-Position.

Image Reset
You can replace all image settings with the factory default values.
English - 19
BN68-01939A-Eng.indd 19
2009-04-15 오후 2:54:38
PC Display
❑ Setting Up Your PC Software (Based on Windows XP)
1.
2.
3.
4.
The Windows display-settings for a typical computer are shown below.
The actual screens on your PC will probably be different, depending upon your
particular version of Windows and your particular video card. However, even if your
actual screens look different, the same basic set-up information will apply in almost
all cases. (If not, contact your computer manufacturer or Samsung Dealer.)
First, click on ‘Control Panel’ on the Windows start menu.
When the control panel window appears, click on ‘Appearance and Themes’ and a
display dialog-box will appear.
When the control panel window appears, click on ‘Display’ and a display dialog-box
will appear.
Navigate to the ‘Settings’ tab on the display dialog-box.
The correct size setting (resolution)
Optimum: 1920 X 1080 pixels.
If a vertical-frequency option exists on your display settings dialog box, the correct
value is ‘60’ or ‘60 Hz’. Otherwise, just click ‘OK’ and exit the dialog box.
❑ Display Modes
Both screen position and size will vary depending on the type of PC monitor and its resolution.
The resolutions in the table are recommended.

D-Sub and HDMI/DVI Input
Mode
Resolution
Horizontal Frequency (kHz)
Vertical Frequency (Hz)
Pixel Clock Frequency (MHz)
Sync Polarity (H/V)
IBM
640 x 350
720 x 400
31.469
31.469
70.086
70.087
25.175
28.322
+/-/+
MAC
640 x 480
832 x 624
1152 x 870
35.000
49.726
68.681
66.667
74.551
75.062
30.240
57.284
100.000
-/-/-/+
VESA CVT
720 x 576
1152 x 864
1280 x 720
1280 x 720
1280 x 960
35.910
53.783
44.772
56.456
75.231
59.950
59.959
59.855
74.777
74.857
32.750
81.750
74.500
95.750
130.000
-/+
-/+
-/+
-/+
-/+
VESA DMT
640 x 480
640 x 480
640 x 480
800 x 600
800 x 600
800 x 600
1024 x 768
1024 x 768
1024 x 768
1152 x 864
1280 x 800
1280 x 800
1280 x 960
1280 x 1024
1280 x 1024
1360 x 768
1440 x 900
1440 x 900
1680 x 1050
31.469
37.861
37.500
37.879
48.077
46.875
48.363
56.476
60.023
67.500
49.702
62.795
60.000
63.981
79.976
47.712
55.935
70.635
65.290
59.940
72.809
75.000
60.317
72.188
75.000
60.004
70.069
75.029
75.000
59.810
74.934
60.000
60.020
75.025
60.015
59.887
74.984
59.954
25.175
31.500
31.500
40.000
50.000
49.500
65.000
75.000
78.750
108.000
83.500
106.500
108.000
108.000
135.000
85.500
106.500
136.750
146.250
-/-/-/+/+
+/+
+/+
-/-/+/+
+/+
-/+
-/+
+/+
+/+
+/+
+/+
-/+
-/+
-/+
VESA GTF
1280 x 720
1280 x 1024
52.500
74.620
70.000
70.000
89.040
128.943
-/+
-/-
VESA DMT
/ DTV CEA
1920 x 1080p
67.500
60.000
148.500
+/+
N When using an HDMI / DVI cable connection, you must use the HDMI IN 2(DVI) jack.
N The interlace mode is not supported.
N The set might operate abnormally if a non-standard video format is selected.
English - 20
BN68-01939A-Eng.indd 20
2009-04-15 오후 2:54:38
Sound Control
Changing the Sound Setting
❑ Mode
Sound
You can select the type of special sound effect to be used when watching a given
broadcast.
• Standard: Selects the normal sound mode.
• Music: Emphasizes music over voices.
• Movie: Provides the best sound for movies.
• Clear Voice: Emphasizes voice over other sounds.
• Custom: Recalls your customized sound settings. (see Customizing the Sound)
Mode
: Custom
►
Equalizer
SRS TruSurround HD : Off
Auto Volume
: Off
Speaker Select : TV Speaker
Sound Select : Main
Sound Reset
T Press the TOOLS button to display Tools menu.
You can also set the sound mods by selecting Tools → Sound Mode.
❑ Equalizer
The sound settings can be adjusted to suit your personal preferences.
• Mode: You can select a sound mode to suit your personal preferences.
• Balance: Controls the balance between the right and left speakers.
• 100Hz / 300Hz / 1kHz / 3kHz / 10kHz (Bandwidth Adjustment): To adjust the level of different bandwidth frequencies.
• Reset: Resets the equalizer settings to the default values.
❑ SRS TruSurround HD
SRS TruSurround HD is the combined technology of TruSurround and FOCUS, TruBass.
SRS TruSurround HD is down mixing technology that makes the Surround Sound effect of virtual 5.1 channel via two speakers.
This function provide not only rich deep bass at a low-pitched sound but also improve the resolution at a high-pitched sound.
T Press the TOOLS button to display Tools menu.
You can also set the SRS TruSurround HD by selecting Tools → SRS TS HD.
TruSurround HD, SRS and the
symbol are trademarks of SRS Labs, Inc.
TruSurround HD technology is incorporated under license from SRS Labs, Inc.
→� ������
Off / ��
On
❑ Auto Volume ��
Each broadcasting station has its own signal conditions, and so it is not easy to adjust the volume every time the channel is
changed. This feature lets you automatically adjust the volume of the desired channel by lowering the sound output when the
modulation signal is high or by raising the sound output when the modulation signal is low.
❑ Speaker Select → External Speaker / TV Speaker
If you want to hear the sound through separate speakers, cancel the internal amplifier.
+, M MUTE buttons do not operate when the Speaker Select is set to External Speaker.
N If you select External Speaker in the Speaker Select menu, the sound settings will be limited.
N The –
TV's Internal Speakers
Audio Out (L / R Out) to Sound System
TV / AV / Component / PC / HDMI
TV / AV / Component / PC / HDMI
TV Speaker
Speaker Output
Sound Output
External Speaker
Mute
Sound Output
Video No Signal
Mute
Mute
Manufactured under license from Dolby Laboratories.
Dolby and the double-D symbol are trademarks of Dolby Laboratories.
Continued...
English - 21
BN68-01939A-Eng.indd 21
2009-04-15 오후 2:54:39
❑ Sound Select
When the PIP feature is activated, you can listen to the sound of the sub (PIP) picture.
• Main: Use to listen to the sound of the main picture.
• Sub: Used to listen to the sound of the sub picture.
❑ Sound Reset
Sound
You can restore the Sound settings to the factory defaults.
• Reset All: All the sound values return to default settings.
• Reset Sound Mode: Current sound values return to defalt settings.
• Cancel: Select the sound reset options.
Speaker Select : TV Speaker
Sound Select
: Main
Sound Reset
►
Selecting the Sound Mode
When you set to Dual l ll, the current sound mode is displayed on the screen.
Type of broadcast
Regular broadcast
(Standard audio)
NICAM
Stereo
Stereo
Anynet+ (HDMI-CEC)
Mono (Normal use)
Regular + NICAM
Mono
NICAM
Mono
(Normal)
NICAM-Stereo
NICAM
Stereo
Mono
(Normal)
NICAM Dual-I/II
A2
Tools
On-screen indication
NICAM
Dual-1
Regular broadcast
(Standard audio)
Bilingual or DUAL-I/II
Dual I
Stereo
Stereo
NICAM
Dual-2
Mono
(Normal)
Picture Size :
16:9
Picture Mode :
Standard
Sound Mode
:
Custom
Sleep Timer :
Off
SRS TS HD
:
Off
Energy Saving :
Dual I II
◄
Off
Mono
►
Add to Favourite
U Move
L Adjust
e Exit
Mono (Normal use)
Dual II
Mono
(Forced mono)
T Press the TOOLS button to display Tools menu.
You can also set the dual I II by selecting Tools → Dual I II.
N
N
N
O
If the stereo signal is weak and an automatic switching occurs, then switch to the mono.
This function is only activated in stereo sound signal. It is deactivated in mono sound signal.
This function is only available in TV mode.
You can select these options simply by pressing the DUAL button on the remote control.
English - 22
BN68-01939A-Eng.indd 22
2009-04-15 오후 2:54:39
Function Description
Configuring the Setup Menu
❑ Language
Setup
It is variable depending on the model. When you start using the television for the
first time, you must select the language which will be used for displaying menus and
indications.
❑ Game Mode
Language
: English
►
Time
When connecting to a game console such as PlayStation™ or Xbox™, you can enjoy a
more realistic gaming experience by selecting the game menu.

Plug & Play
Game Mode
: Off
BD Wise
: Off
Network Type
: Cable
Network Setup
When the Game Mode is On
Child Lock
: On
• Picture Mode is automatically changed to Standard and users cannot change the
Change PIN
mode.
• Sound Mode is automatically changed to Custom and users cannot change the
mode. Adjust the sound using the equalizer.
• The Reset in the Sound menu is activated. Reset function initializes the Equalizer settings to the factory default setting.
N Game Mode is not available in regular TV mode or Game Mode set to Off.
N If the picture is poor when external device is connected to TV, check if Game Mode is On.
N This function supports only game function.
N If you display the TV menu in Game mode, the screen shakes slightly.
N The mark (
) appears on the screen which means that Game Mode is on with the selected source.
N Game mode is not available in PC mode.
N While PIP is in operation, the Game Mode function cannot be used.
❑ BD Wise
Wise is a function that enables you automatically to set the optimum condition all connected Samsung devices that support
BD wise.
N This function is active only when an external device is connected to the TV via HDMI.
N When the BD Wise set to On, picture mode is automatically changed under the conditions
❑ Child Lock → Off / On
This feature allows you to prevent unauthorized users, such as children, from watching unsuitable programmes by muting out video
and audio.
N Before the setup screen appears, the PIN number input screen appears. Enter your 4 digit PIN number.
N The default PIN number of a new TV set is ‘0-0-0-0’. You can change the PIN by selecting Change PIN from the menu.
N You can lock some channels in Channel List. (refer to page 15)
N Child Lock is available only in TV mode. .
❑ Change PIN
You can change your personal ID number that is required to set up the TV.
N Before the setup screen appears, the PIN number input screen appears. Enter your 4 digit PIN number.
N The default PIN number of a new TV set is ‘0-0-0-0’.
N If you forget the PIN code, press the remote control buttons in the following sequence, which resets the PIN to ‘0-0-0-0’ :
POWER (Off), MMUTE, 8, 2, 4, POWER (On).
❑ Melody →�
�� Off / Low / Medium / High3
The TV power on / off melody sound can be adjusted.
N The Melody does not play
- When no sound is output from the TV because the M MUTE button has been pressed.
- When no sound is output from the TV because the –
(Volume) button has been pressed.
- When the TV is turned off by Sleep Timer function.
❑ Energy Saving
This feature adjusts the brightness of the TV in order to reduce power consumption. When watching TV at night, set the
Energy Saving mode option to High to reduce eye fatigue as well as power consumption.
• Off: Turns off the energy saving function.
• Low: Sets the TV to low energy saving mode.
• Medium: Sets the TV to medium energy saving mode.
• High: Sets the TV to high energy saving mode.
T Press the TOOLS button to display Tools menu.
You can also set the energy saving option by selecting Tools → Energy Saving.
English - 23
BN68-01939A-Eng.indd 23
2009-04-15 오후 2:54:39
Setting the Time
❑ Clock
Plug & Play
Setup
Setting the clock is necessary in order to use the various timer features of the TV.
N The current time will appear every time you press the INFO button.
N If you disconnect the power cord, you have to set the clock again.
You can set the current time manually.
N You can set the day, month, year, hour, or minute directly by pressing the number
buttons on the remote control.
Language
: English
Time
Game Mode
: Off
BD Wise
: Off
Network Type
: Cable
Network Setup
Child Lock
❑ Sleep Timer → Off / 30 min / 60 min / 90 min / 120 min /
: On
Change PIN
150 min / 180 min
Melody
The sleep timer automatically shuts off the TV after a preset time.
N The TV automatically switches to standby mode when the timer reaches 0.
N To cancel the Sleep Timer function, select Off.
T Press the TOOLS button to display Tools menu.
You can also set the sleep timer by selecting Tools → Sleep Timer.
❑ Timer 1 / Timer 2 / Timer 3
►
: Medium
Time
Clock
: 0 : 07 Sleep Timer
: Off
Timer 1
: Inactivated
Timer 2
: Inactivated
Timer 3
: Inactivated
Three different on / off timer settings can be made.
�����������������������������������������������
the hour, minute, and Activate/Inactivate.
• On Time: Set
(To activate timer with the setting you’ve chosen, set to Activate.)
�������������������������������������������������
the hour, minute, and Activate / Inactivate.
• Off Time: Set
(To activate timer with the setting you’ve chosen, set to Activate.)
• Volume: Selects the volume level.
• Source: Selects TV or USB device.
N When you select the TV, you can set the Channel.
- Channel: Selects the desired channel.
N When you select the USB or TV Memory, you can set the Contents.
- Contents: Selects the desired contents on the USB or TV Memory.
U Move
►
E Enter
R Return
• Repeat: Select
������� Once, Everyday, Mon~Fri, Mon~Sat, Sat~Sun, or Manual.
N You must set the clock first.
N You can set the hour, minute, or channel directly by pressing the number buttons on the remote control.
N Auto Power Off
When you set the timer On, the television will eventually turn off, if no controls are operated for 3 hours after the TV was
turned on by the timer. This function is only available in timer On mode and prevents overheating, which may occur if a TV is
on for too long time.
Source List / Edit Name
❑ Source List

TV, PC, AV1, AV2, Component1, Component2, HDMI1, HDMI2/DVI, HDMI3,
HDMI4, USB.
N You can choose only those external devices that are connected to the TV.
N Using the Colour buttons on the remote with the Source list
• Red (Refresh): Refreshes the connected external devices. Press this if your Source is
on and connected, but does not appear in the list.
• T TOOLS (Tools): Displays the Edit Name and Information menus.
Input
Use to select TV or other external input sources such as DVD players or Cable Box /
Satellite receivers (Set-Top Box) connected to the TV. Use to select the input source of
your choice.
Source List
Edit Name
N Press the SOURCE button on the remote control to view an external signal source.
TV mode can be selected by pressing the TV button, number buttons (0~9), and the
P
button on the remote control.
❑ Edit Name
You can name the device connected to the input jacks to make your input source
selection easier.
 VCR / DVD / Cable STB / Satellite STB / PVR STB / AV Receiver / Game /
Camcorder / PC / DVI / DVI PC / TV / IPTV / Blu-ray / HD DVD / DMA
N When a PC with a resolution of 1920x1080@60Hz is connected to the HDMI IN 2 (DVI) port, you should set the HDMI2/DVI
mode to PC in the Edit Name of the Input mode.
N When connecting an HDMI/DVI cable to the HDMI IN 2(DVI) port, you should set the HDMI2/DVI mode to DVI or DVI PC in the
Edit Name of the Input mode. In this case, a separate sound connection is required.
English - 24
BN68-01939A-Eng.indd 24
2009-04-15 오후 2:54:40
Supported Program
❑ Product Guide
Support
The Product Guide gives you information on the most important features of this TV.
• Mediⓐ2.0: Internet@TV-Content Service, Content Library Flash, USB2.0 Movie,
DLNA Wireless
• Picture Quality: 1080 Full HD Motion, Ultra FilterBright, 100Hz Motion Plus,
Cinema Smooth, Picture Mode
• Eco-Friendly: Energy Saving, Eco-Material
Product Guide
►
Self Diagnosis
Software Upgrade
HD Connection Guide
Contact Samsung
❑ Self Diagnosis

Picture Test
If you think you have a picture problem, perform the picture test. Check the colour pattern on the screen to see if the problem
stillexists.
N Does the problem still exist with this test photo? appears on the screen.
N If the test pattern does not appear or there is noise in the test pattern, select Yes.
If the test pattern is properly displayed, select No.
• Yes : There may be a problem with the TV. Contact Samsung’s Call Center for assistance.
• No : There may be a problem with your external equipment. Please check your connections. If the problem still persists, refer to
the external device’s user manual.

Sound Test
If you think you have a sound problem, please perform the sound test.
You can check the sound by playing a built-in melody sound through the TV.
N Does the problem still exist with this sound test? appears on the screen.
N If during the sound test you can hear sound only from one speaker or not at all, select Yes.
If you can hear sound from the speakers, select No.
• Yes : There may be a problem with the TV. Contact Samsung’s Call Center for assistance.
• No : There may be a problem with your external equipment. Please check your connections. If the problem still persists, refer to
the external device’s user manual.
N If you hear no sound from the TV’s speakers, before performing the sound test, make sure Speaker Select is set to TV speaker
in the Sound menu.
N The melody will be heard during the test even if Speaker Select is set to External Speaker or the sound is muted by pressing the
MMUTE button.
N If headphones are connected, the test melody will play through the headphones.

Signal Strength (Digital channels only)
You can adjust your antenna to improve the reception of available digital channels.
N If the signal strength meter indicates that the signal is weak, physically adjust your antenna to increase the signal strength.
Continue to adjust the antenna until you find the best position with the strongest signal.
❑ Software Upgrade
To keep your product up-to-date with new Digital Television features then software
upgrades are periodically broadcast as part of the normal Television signal. It will
automatically detect these signals and display the software upgrade banner. You are
given the option to install the upgrade.
TV Side Panel

By USB
USB Drive
Insert a USB drive containing the firmware upgrade into TV. Please be careful to not
disconnect the power or remove the USB drive while upgrades are being applied.
The TV will turn off and turn on automatically after completing the firmware upgrade.
Please check the firmware version after the upgrades are complete. When software
is upgraded, video and audio settings you have made will return to their default (factory) settings. We recommend you write down
your settings so that you can easily reset them after the upgrade.

Alternative Software
Replace the current software with the alternative.
Contact Samsung
❑ HD Connection Guide
The brief instruction on How to get the best performance from your new
HDTV is displayed.
We offer the connection method for HD devices.
N You can move the previous or next page by pressing the ◄ or ► button.
❑ Contact Samsung
You can know the Samsung Call center, website and information for product.
Please contact Samsung if you are having problems operating this TV.
Contact Samsung
- Call Center : Refer to the User Manual.
- Web Site : Visit www.samsung.com, then select your country.
Some units have the firmware and you can get it on www.samsung.com
Product Infomation
- Model Code : PS50B650
- Software Version: T-CHEAEAC-1001.3
- The serial and version numbers can be found on the sticker on the right side of your TV.
OK
E Enter
R Return
English - 25
BN68-01939A-Eng.indd 25
2009-04-15 오후 2:54:40
Media Play
Connecting a USB Device
1. Press the POWER button to turn the TV on.
2. Connect a USB device containing photo, music and movie files to the USB jack on
the side of the TV.
TV Side Panel
N If you enter the Media Play mode with no USB device connected the message No
N
N
N
N
N
N
N
N
N
N
N
N
N
N
external storage device found. Check the connection status. will appear. In this
case, insert the USB device, exit the screen by pressing the MEDIA.P button on the
USB Drive
remote control and enter the Media Play screen again.
MTP (Media Transfer Protocol) is not supported.
The file system only supports FAT16/32 (The NTFS file system is not supported).
Certain types of USB Digital camera and audio devices may not be compatible with this TV.
Media Play only supports USB Mass Storage Class devices (MSC). MSC is a Mass Storage Class Bulk-Only Transport device.
Examples of MSC are Thumb drives and Flash Card Readers (Both USB HDD and HUB are not supported.)
Please connect directly to the USB port of your TV. If you are using a separate cable connection, there may be a USB compatibility
problem.
Before connecting your device to the TV, please back up your files to prevent them from damage or loss of data. SAMSUNG is not
responsible for any data file damage or data loss.
Do not disconnect the USB device while it is loading.
MSC supports MP3 and JPEG files, while a PTP device supports JPEG files only.
The sequential JPEG format is supported.
The higher the resolution of the image, the longer it takes to display on the screen.
The maximum supported JPEG resolution is 15360X8640 pixels.
For unsupported or corrupted files, the Not Supported File Format message is displayed.
If the number of photo files exceeds 4000 (or the number of music files exceeds 3000), any files exceeding the 4000 limit may not
be displayed in the Photo List (or Music List).
MP3 files with DRM that have been downloaded from a non-free site cannot be played. Digital Rights Management (DRM)
is a technology that supports the creation of content, the distribution and management of the content in an integrated and
comprehensive way, including the protection of the rights and interests of the content providers, the prevention of the illegal copying
of contents, as well as managing billings and settlements.
When moving to a photo, loading may take a few seconds. At this point, the loading icon will appear at the screen.
❑ Using the Remote Control Button in Media Play Menu
Button
Operations
▲/▼/◄/►
Move the cursor and select an item.
ENTERE
Select the currently selected item.
While playing a slide show, movie, or music file:
- Pressing the ENTERE button during play pauses the play.
- Pressing the ENTERE button during pause resumes the play.
Play or pause the side show, music, or movie file.
RETURN
TOOLS
Return to the previous menu.
Run various functions from the Photo, Music and Movie menus.
Stop the current slide show, music or movie file.
Jump to previous group/Jump to next group.
INFO
MEDIA.P
P
/
EXIT
Show file information.
Enter/Exit Media Play mode.
Stop Media Play mode and Returns to TV mode.
Exit Media Play mode.
English - 26
BN68-01939A-Eng.indd 26
2009-04-15 오후 2:54:40
Using the Media Play Function
This function enables you to view and listen to photo, music and movie files saved on a USB Mass Storage Class (MSC) device.
❑ Entering the Media Play Menu
1. Press the MENU button. Press the ▲ or ▼ button to select Application, then
press the ENTERE button.
2. Press the ▲ or ▼ button to select Media Play (USB&DLNA), then press the
ENTERE button.
N The Media Play menu is displayed.
Media Play
851.98MB/995.00MB Free
USB : USB
PHOTO
O Press the MEDIA.P button on the remote control to display the Media Play
menu.
O Press the SOURCE button on the remote control repeatedly to select USB or
DLNA, then press the ENTERE button.
3. Press the Red button, then press the ▲ or ▼ button to select the corresponding
USB Memory Device (i.e. if connected through a hub). Press the ENTERE button.
N This function differs depending on the USB Memory Device/ DLNA device
connected to TV.
N The selected USB device name appears at the bottom left of the screen.
Photo
USB
Music
Movie
Setup
 Device
R Return
4. Press the ◄ or ► button to select an icon (Photo, Music, Movie, Setup), then
press the ENTERE button.
N To exit Media Play mode, press the MEDIA.P button on the remote control.
N Y����������������������������������������������������
ou can enj������������������������������������������
oy game movies. (Not support game program)
Photo
❑ Removing a USB Memory Device Safely
Folder
❑ Screen Display
Preference Basic View
Timeline
▶
3
2009
Mar
▶
Photo
▶
1
2
Colour
▶
4/6
Slide Show
Copy
Play Current Group
IMG_0345
Copy Current Group
Information
IMG_0346
IMG_0349
IMG_0335
Remove Safely
../ folder name/
USB
 Device
Select T Tools
R Upper Folder
Nov
▶
IMG_03496
 Device
Colour
◀
USB
Timeline
1
1
1/67
IMG_0335
4
Basic View
Folder
Apr Jun
2009/5/15
c
IMG_03496
Preference
▶
You can remove the device safely from the TV.
1. Press the TOOLS button in the Media Play file list screen, or while a SlideShow
or music file is being played.
2. Press the ▲ or ▼ button to select Remove Safely, then press the ENTERE
button.
3. Remove the USB device from the TV.
6
Favorites Settings
IMG_0343
5
IMG_03496
1File(s) Selected
Select
T
Tools R Return
1.
2.
3.
4.
Currently selected file: The currently selected file is highlighted.
Current Sort Standard: This field shows the current standard for sorting files.
View Groups: The sorting group including the currently selected photo is highlighted.
Current Device: Shows the currently selected device name.
N Red (Device) button: Selects a connected device.
5. Item Selection Information: Shows the number of photos that are selected by pressing the Yellow button.
6. Help Items
• Green (Favourites Settings) button: Changes the Favourites Settings for the selected file. Press this button repeatedly until
the desired value appears.
• Yellow (Select) button: Selects file from the file list. Selected files are marked with a symbol c. Press the yellow button again
to cancel a file selection.
•
TOOLS (Tools) button: Displays the option menus. (The option menu changes according to the current status.)
• R Return button: Return to previous menu.
English - 27
BN68-01939A-Eng.indd 27
2009-04-15 오후 2:54:44
Using and Sorting Photo List
You can sort photos in the Photo List by a particular standard.
Photo
1. Press the ▲ button twice, then press the ◄ or ► button to select a sorting standard
in the Photo list.
(Basic View, Timeline, Colour, Folder, Preference)
Preference Basic View
▶
▶
▶
2009
Mar
Folder
Nov
◀
▶
2. Press the
by the user.
(Play)/ENTERE
(REW) or
Colour
Apr Jun
2009/5/15
1/67
N The photos are sorted according to the newly selected sorting standard.
N To move to the previous/next group, press the
Timeline
(FF) button.
IMG_03496
IMG_03496
IMG_0343
IMG_0335
button to start the Slide Show in the order selected
USB
 Device
Favorites Settings
IMG_03496
Select T Tools R Return
N The information of a photo file is automatically set.
N The colour information extracted from a photo file may be different from the user’s expectations.
N Photo information is automatically set. You can change the Colour, and Preference.
N Photos for which information cannot be displayed are set as Unclassified.
N PTP does not support folder sort mode.
❑ Sorting Standard for the Photo List

Basic View
It shows whole folder. You can view the photo by selecting the folder.
N When sorted according to the Basic View, you cannot set Favorite files.

Timeline
It sorts and shows photos by date. It sorts by year and month from the earliest photo.

Colour
It sorts photos by colour. You can change the photo colour information.
N To use this function, set the Use Colour View in the Setup menus to On.
N Colour options: Red, Yellow, Green, Blue, Magenta, Black, Gray, Unclassified.

Folder
It sorts photos by folder. If there are many folders in USB, the photos files are shown in order in each folder. The photo file in the
root folder is shown first and the others are shown in alphabetical order by name.

Preference
It Sorts photos by preference (Favourites). You can change the photo preferences.
N Changing the Favourites Settings.
Select the desired photo in the Photo list, then press the Green button repeatedly until the desired setting appears.
N Favourites options: ★ ★ ★ , ★ ★ ★ , ★ ★ ★ , ★ ★ ★
❑ Photo List Tools Menu
Photo
Slide Show
You can play a Slide Show using the photo files on the USB memory device.
Copy
You can copy the selected photo files to TV's memory.

Play Current Group
You can play a Slide Show using only the photo files in the currently selected sorting
group.
Preference
Basic View
▶

Folder
▶

Timeline
Colour
1
1
4/6
Slide Show
Copy
Play Current Group
IMG_0345
Copy Current Group
Information
IMG_0346
IMG_0349
IMG_0335
Remove Safely
../ folder name/
USB
 Device

Change Group
You can change the colour information of photo files.
N The group information of the current file is updated and the file is moved to the new group.
N To change the information of multiple files, select the files you want by pressing the yellow button.

Copy Current Group
You can copy the photo files in the currently selected sorting group to TV's memory.
Select T Tools
R Upper Folder
Continued...
English - 28
BN68-01939A-Eng.indd 28
2009-04-15 오후 2:54:47

Information
The photo file information including the name, the size, the resolution, the date modified and the path is displayed.
N You can view the information of photo files during a Slide Show using the same procedures.
O Alternatively, select a photo from the photo list and press the INFO button to view
the information.

Remove Safely
You can remove the device safely from the TV.
Viewing a Photo or Slide Show
❑ Viewing a Slide Show
1. Press the ◄ or ► button to select the desired photo in the Photo list.
2. Press the TOOLS button.
3. Press the ▲ or ▼ button to select Slide Show, then press the ENTERE
button.
N All files in the photo list will be used for the Slide Show.
r Normal IMG_0335.jpg
3648x2432 2009/3/15
1/4
N During the slide show, files are displayed in order from the currently shown file.
N The Slide Show progresses in the order sorted in the Photo list.
N Music files can be automatically played during the Slide Show if the
USB
E Pause lr Previous/Next
T
Tools R Return
Background Music is set to On. (Refer to page 30).
(Play)/ENTERE button on the
O While a photo list is displayed, press the
remote control to start slide show.
N SlideShow Control Buttons
ENTERE
Play/Pauses the Slide Show.
Exit Slide Show and return to the photo list.
Play the Slide Show.
T TOOLS
Pause the Slide Show.
/
Run various functions from the Photo menus.
Change the SlideShow playing speed.
❑ Playing current group
1.
2.
3.
4.
Press the ◄ or ► button to select a sorting standard. (Basic View, Timeline, Colour, Folder, Preference)
Press the
(REW) or
(FF) button to select the desired group.
Press the ▼ button twice, then press the TOOLS button.
Press the ▲ or ▼ button to select Play Current Group, then press the ENTERE button.
N Only the photos in the sorting group including the selected files will be used for the Slide Show.
❑ Playing the selected photo files
1. Press the ◄ or ► button to select the desired photo in the Photo list.
2 . Press the yellow button. Repeat the above operation to select multiple photos.
N The c mark appears to the left of the selected photo.
N If you select one file, the slide show will not be performed.
N To deselect all selected files, press the TOOLS button and select Deselect All.
3. Press the
(Play) / ENTERE button.
N The selected files will be used for the slide show.
Continued...
English - 29
BN68-01939A-Eng.indd 29
2009-04-15 오후 2:54:48
❑ Slide Show Tools Menu


Stop Slide Show / Start Slide Show
You can start or stop a SlideShow.
Tools
Slide Show Speed → Normal / Fast / Slow
You can select the slide show speed only during the slide show.
N You can also change the speed of the Slide Show by pressing the
(FF) button during the Slide Show.
(REW) or
Stop Slide Show
Tools
Slide Show Speed :
Normal
Slide Show Effect :Fade1
Rotate
Zoom
Background Music
Picture Setting
Sound Setting
Information
›

Slide Show Effect
You can set variously the slide show effect.
• Fade1, Fade2, Blind, Spiral, Checker, Linear, Stairs, Wipe, Random, None

Rotate →�
�� 0˚/ 90˚ / 180˚ / 270˚
You can rotate photos saved on a USB memory device.

Zoom ��
→� x1 / x2 / x4
You can magnify photos saved on a USB memory device.
N To move the enlarged photo image, press the ENTERE button, then press the ▲/▼/◄/► buttons. Note that when the
enlarged picture is smaller than the original screen size, the location change function doesn’t work.
N The enlarged file is not saved.

Background Music
You can set and select background music when watching a Slide Show.
N To use this feature, there must be music on the USB device.
N Loading music files is needed to change BGM mode. Play music files in music category to load.
• Background Music →�
�� On / Off
• BGM Mode →�
�� Mood / Selected File / Shuffle
• BGM Mood →� Energetic / Rhythmical / Sad / Exciting / Calm
U Move
E Enter
e Exit
N If you set BGM Mode to Mood, you can select a mood.
N You cannot select a mood not part of the music files on the USB memory device.
• Select Music File
N If you set BGM Mode to Selected File, you can select a music file.

Picture Setting / Sound Setting
Refer to page 36.

Information
The photo file information is displayed.

Remove Safely
You can remove the device safely from the TV.
English - 30
BN68-01939A-Eng.indd 30
2009-04-15 오후 2:54:48
Using and Sorting the Music List
You can sort music files in the Music List by a particular standard.
1. Press the ▲ button twice, then press the ◄ or ► button to select a sorting standard
in the Music list. (Basic View, Title, Artist, Mood, Genre, Folder, Preference)
Music
Preference
Folder
Basic View
▶
N To move to the previous/next group, press the
(REW) or
▶
▶
N Music files are sorted according to the newly selected sorting standard.
(FF) button.
3/4
Mr A-Z
▶
N
N
N
▶
2009
Pop
NPKI
N The information of the music files is automatically set.
N
Artist
Carol kidd
2. Press the ENTERE button to start playing music in the order selected by the user.
N The Mood information extracted from a music file may differ from the
Title
1
1
usermanual
Heaven
When I Dream
../ folder name/
Select T Tools
USB  Device
expectations of the user.
Music information is automatically set. You can change the Mood and Preference.
Music files for which information cannot be displayed are set to Unclassified.
If there is no title information for a music file, the filename is displayed.
If no information is available for the Genre, Artist, Album, or Year the corresponding item is displayed as blank.
R Upper Folder
❑ Sorting Standard for the Music List

Basic View: It shows whole folder. You can view the photo by selecting the folder.
N When sorted according to the Basic View, you cannot set Favorite files.

Title: It sorts the Music titles in alphabetical order, and shows the music file.

Artist: It sorts the music file by artist in alphabetical order.

Mood: It sorts music files by the mood. You can change the music mood information.
N Mood options: Energetic, Rhythmical, Sad, Exciting, Calm, Unclassified

Genre: It sorts music files by the genre.

Folder: It sorts music files by the folder. If there are many folders in USB, the files are shown in order in each folder. The music
file in the Root folder is shown first and the others are shown in alphabetical order by name.

Preference: It sorts music files by preference (Favourites). You can change the music files preferences.
N Changing the Favourites Settings
Select the desired music file in the Music list, then press the Green button repeatedly until the desired setting appears.
★★★ , ★★★ , ★★★ , ★★★
N Favourites options:



Music
Preference
Folder
Basic View
▶

Play Current Group
You can only play music files in the currently selected sorting group.
▶
❑ Music List Tools Menu
Copy
You can copy the selected music files to TV's memory.
Title
Artist
1
1
3/4
Play Current Group
Carol kidd
Copy
Mr A-Z
Copy Current Group
▶
Information
2009
Change Group
You can change the mood information of music files.
N The group information of the current file is updated and the file is moved to the
new group.
N To change the information of multiple files, select files by pressing the yellow
button.
NPKI
Pop
NPKI
usermanual
../ folder name/
USB
 Device
Remove Safely
Select
Sky
Heaven
When I Dream
T
Tools
Select T Tools
RUpper Folder
R Upper Folder
Copy Current Group
You can copy the music files in the currently selected sorting group to TV's memory.
Information
The music file information including the name, the size, the date modified and the path is displayed.
N You can view the information of music files during a Slide Show using the same
procedures.
O Alternatively, select a music file from the music list and press the INFO button to
view the information.
 Remove Safely
You can remove the device safely from the TV.

English - 31
BN68-01939A-Eng.indd 31
2009-04-15 오후 2:54:48
Playing a Music
❑ Playing a music file
r
1. Pressing the ◄ or ► button to select a music file to be played.
r
00:00:02 / 00:04:55
1/3
2. Press the
(Play)/ENTERE button.
r
When I Dream
N This menu only shows files with the MP3 file extension. Files with other
file extensions are not displayed, even if they are saved on the same USB
device.
N
(REW) or
(FF) buttons do not function during play.
N The selected file is displayed at the top with its playing time.
N To adjust the music volume, press the ������
volume button on the remote control.
E Pause lr Previous/Next T Tools R Return
USB
To mute the sound, press the M MUTE button on the remote control.
N The playing duration of a music file may be displayed as ‘00:00:00’ if its playing time information is not found at the start of
the file.
r
Geek In The Pink
Heaven
N Music Play Control Buttons
ENTERE
Play/Pauses the music file.
Play the music file
Pause the music file
Exit play mode and return to the music list.
T TOOLS
Run various functions from the Music menus.
N Music function information icon
When all music files in the folder (or the selected file) are repeated. Repeat Mode is On.
When all music files in the folder (or the selected file) are played once. Repeat Mode is Off.
❑ Playing the music group
1.
2.
3.
4.
Press the ◄ or ► button to select a sorting standard.
(Basic View, Title, Artist, Mood, Genre, Folder, Preference)
Press the
(REW) or
(FF) button to select the desired group.
Press the ▼ button twice, then press the TOOLS button.
Press the ▲ or ▼ button to select Play Current Group, then press the ENTERE button.
N The music files in the sorting group including the selected file are played.
❑ Playing the selected music files
1. Press the ◄ or ► button to select the desired music file in the music list.
2. Press the yellow button. Repeat the above operation to select multiple music files.
N The c mark appears to the left of the selected music file.
N To deselect all selected files, press the TOOLS button and select Deselect All.
3. Press the
(Play)/ENTERE button.
N Only the selected file is played.
❑ Music Play Tools Menu

Repeat Mode → On/Off
You can play music files repeatedly.

Picture Setting / Sound Setting
Refer to page 36.

Information
The music file information is displayed.

Remove Safely
You can remove the device safely from the TV.
Tools
Repeat Mode
Picture Setting
Sound Setting
Information
Remove Safely
U Move
◄
On
š™ Adjust
►
e Exit
English - 32
BN68-01939A-Eng.indd 32
2009-04-15 오후 2:54:49
▶
Using and Sorting the Movie List
Movie
Preference
Timeline
Basic View
▶
N The movie files are sorted according to the newly selected sorting standard.
1/5
(FF) button.
(Play)/ENTERE button to play the movie in the order selected by
N The movies are sorted according to the newly selected sorting standard.
▶
2. Press the
the user.
(REW) or
Folder
2009/4/15
◀
N To move to the previous/next group, press the
Tiltle
Apr
▶
1. Press the ▲ button twice, then press the ◄ or ► button to select a sorting standard
in the Movie list. (Basic View, Timeline, Title, Folder, Preference)
▶
You can sort movies in the Movie List by a particular standard.
MOVIE_005
MOVIE_000
MOVIE_003
MOVIE_001
USB
 Device
Favorites Settings
MOVIE_004
Select T Tools R Return
N Movie information is automatically set. You can change the Preference.
❑ Sorting Standard for the Movie List

Basic View
It shows whole folder. You can view the photo by selecting the folder.
N When sorted according to the Basic View, you cannot set Favorite files.

Timeline
It sorts and shows movies by date. It sorts by year and month from the earliest movie.

Title
It sorts and displays the Movie titles in symbol/number/alphabet/special order.

Folder
If there are many folders in USB, the movies files are shown in order in each folder. The movie file in the root folder is shown first
and the others are shown in alphabetical order by name.

Preference
It sorts movies by preference (favourites). You can change the movie preferences.
N Changing the Favourites Settings
Select the desired movie file in the movie list, then press the Green button repeatedly until the desired setting appears.
N Favourites options: ★ ★ ★ , ★ ★ ★ , ★ ★ ★ , ★ ★ ★
❑ Movie List Tools Menu


Movie
Preference
Play Current Group
Using this menu, you can only play movie files in the currently selected sorting
group.
Copy
You can copy the selected movie files to TV's memory.
Basic View
Timeline
Tiltle
Folder
Apr
▶
▶

2009/4/15
1/5
Play Current Group
Copy
Copy Current Group
MOVIE_005
Copy Current Group
You can copy the music files in the currently selected sorting group to TV's memory.
Information
Remove Safely MOVIE_004
MOVIE_000
MOVIE_001
USB
 Device
Favorites Settings
MOVIE_003
Select T Tools R Return

Information
The movie file information including the order of the file in the current directory, the name, the size, the date modified and the path
is displayed.
N A��������������������������������������������������������������������
lternatively, select a movie file from the movie list and press the INFO button to
view the information.

Remove Safely
You can remove the device safely from the TV.
English - 33
BN68-01939A-Eng.indd 33
2009-04-15 오후 2:54:53
Playing a Movie File
r
1. Pressing the ◄ or ► button to select a movie to be played.
2. Press the
(Play) / ENTERE button.
00:00:02 / 00:01:55
r
❑ Playing a movie file
1/3
MOVIE_000.avi
N The selected file is displayed at the top with its playing time.
N The playing duration of a movie file may be displayed as ‘00:00:00’ if its
playing time information is not found at the start of the file.
N Press the ◄ button while playing a video file to rewind by 10 seconds.
N Press the ► button to fast forward by 10 seconds.
USB
E Pause lr Jump T Tools R Return
N Supported Video Formats
Video Codec
File Extention
*.avi
*.mp4
Container
AVI
MP4
Video Decoder
Max Resolution Sti
XviD
720x576
MPEG1
720x576
MPEG2
720x576
H.264 BP
1920x1088
H.264 BP
1920x1088
H.264 HP
1920x1088
MPEG-4 SP
720x576
MPEG-4 ASP
720x576
H.264 BP
1920x1088
H.264 MP
1920x1088
H.264 HP
1920x1088
MPEG-4 SP
720x576
MPEG-4 ASP
720x576
MPEG1 (Program Stream)
1920x1088
MPEG2 (Program Stream)
1920x1088
MPEG2 VOB
1920x1088
*.vob
MPEG2 VRO
1920x1088
others
(ts)
MPEG2 (Transport Stream)
1920x1088
H.264 (Transport Stream)
1920x1088
*.mpg
*.mpeg
*.vro
PS
TS
N Video Play Control Buttons
ENTERE
Play/Pauses the movie file
Play the movie file
Pause the movie file
Exit play mode and return to the movie list.
T TOOLS
Run various functions from the movie menus.
◄/►
Skip backwards through the movie file in 10 second intervals.
▼/▲
Move to the first or last view of the current file.
N Movie function information icon
When all movie files in the folder (or the selected file) are repeated.
Repeat Mode is On.
When all movie files in the folder (or the selected file) are played once.
Repeat Mode is Off.
Continued...
English - 34
BN68-01939A-Eng.indd 34
2009-04-15 오후 2:54:54
❑ Playing the movie group
1. Press the ◄ or ► button to select a sorting standard.
(Basic View, Timeline, Title, Folder, Preference)
2. Press the
(REW) or
(FF) button to select the desired group.
3. Press the ▼ button twice, then press the TOOLS button.
4. Press the ▲ or ▼ button to select Play Current Group, then press the ENTERE button.
N Only the movie files in the sorting group including the selected files will be played.
❑ Playing the selected movie files
1. Press the ◄ or ► button to select the desired movie file in the movie list.
2. Press the yellow button. Repeat the above operation to select multiple movie files.
N The cmark appears to the left of the selected movie file.
N To deselect all selected files, press the TOOLS button and select Deselect All.
3. Press the
(Play)/ENTERE button.
N Only the selected file is played.
❑ Playing movie continuously
If you exit playing movie, playing it continuously later is possible.
With Play continuously function, you can watch movie without watching again from beginning or bothering searching.
1.Select movie file you want to Play continuously by pressing ◄ or ► button from the Movie List.
2. Press the
(Play)/ENTERE button.
3. Select Play continuously by pressing Blue button.
N Movie will begin to play from where it was stopped being played.
N If Cont. movie play help function was set On, a pop-up message will appear when you play movie file you want to Play
continuously.
❑ Movie Play Tools Menu

Picture Setting / Sound Setting
Refer to page 36.

Picture Size
• Fit: Play video at the TV screen size.
• Original: Play video at the original size.

Caption Setting
You can play the movies with caption.
• Caption: On / Off
• Caption Language: Western Europe / Arabic
N Not available in all locations.
Tools
Picture Setting
Sound Setting
Picture Size
Caption Setting
Information
Remove Safely
:
U Move
Fit
 Enter
e Exit
• Caption Size: Large / Small / Standard
• Caption Sync: Adjusts the caption output time.
• Caption Sync Reset: Resets the Sync to the default values.

Information
The movie file information is displayed.

Remove Safely
You can remove the device safely from the TV.
English - 35
BN68-01939A-Eng.indd 35
2009-04-15 오후 2:54:54
Picture / Music Settings Using Media Play
When watching a SlideShow or listening to music using Media Play, you can set the picture and sound.
❑ Picture Setting
1. Press the TOOLS button during a Slide Show or while music is playing.
2. Press the ▲ or ▼ button to select Picture Setting.
3. Press the ◄ or ► button to select the Picture Mode
(Standard, Eco, Movie, or Dynamic).
4. Press the ▲ or ▼ button to move to an item.
(Contrast, Brightness, Cololur, Dynamic Contrast, Black Tone, or Reset)
N Select Reset to initialize the picture settings.
Picture Setting
Picture Mode
Contrast
Brightness
Cololur
Dynamic Contrast
Black Tone
Reset
5. Press the ◄ or ► button to adjust the settings.
◄ Standard ►
:
95
:
45
:
50
: Medium
:
Off
U Move L Adjust  Enter e Exit
N For more information on the picture settings, refer to pages 16~18.
❑ Sound Setting
1. Press the TOOLS button during a Slide Show or while music is playing.
2. Press the ▲ or ▼ button to select Sound Setting.
3. Press the ◄ o r ► button to select the Sound Mode.
(Standard, Music, Movie, Clear Voice, or Custom)
4. Press the ▲ or ▼ button to move to an item.
(Balance, 100Hz / 300Hz / 1KHz / 3KHz / 10KHz (Bandwidth Adjustment), or Reset)
N Select Reset to initialize the sound settings.
Sound Setting
Sound Mode Balance 100Hz
300Hz 1KHz 3KHz 10KHz Reset
5. Press the ◄ or ► button to adjust the settings.
◄ Custom ►
: L50 R50
:
0
:
0
:
0
:
0
:
0
U Move L Adjust  Enter e Exit
N For more information on the sound settings, refer to page 21~22.
Using the Setup Menu
Setup displays the user settings of the Media Play menu.
1.
2.
3.
4 .
Press the MEDIA.P button on the remote control to display the Media Play menu.
Press the ◄ or ► button to select Setup, then press the ENTERE button.
Press the ▲ or ▼ button to select the desired option.
Press the ◄ or ► button to select the option
Media Play
Use Colour View → On / Off
Select to view the colour information in the Photo menu.
N If this is set to ON, the loading time increases for collecting the colour
information.
851.98MB/995.00MB Free
SETUP
N To exit Media Play mode, press the MEDIA.P button on the remote control.

USB : USB
Photo
USB
Music
Movie
Setup
 Device
Return
Setup
Use Colour View
◄
Off
Music Repeat Mode
On
Cont. movie play help On
Get the DivX® VOD registration code
Get the DivX® VOD deactivation code
Screen Saver Run Time
10 min
Information
Remove Safely
►

Music Repeat Mode →�
�� On / Off
Select to repeatedly play music files.

Cont. movie play help →
�� On / Off
Select to display the help pop-up message for continuous movie playback.

Get the DivX® VOD registration code
Move
Adjust
Return
USB  Device
Shows the registration code authorized for the TV. If you connect to the DivX
web site and register the registration code with a personal account, you can download VOD registration file. If you play the VOD
registration using Media Play, the registration is completed. For more information on DivX® VOD, visit www.DivX.com.

Get the DivX® VOD deactivation code
When DivX® VOD is not registered, the registration deactivation code is displayed. If you execute this function when DivX® VOD is
registered, the current DivX® VOD registration is deactivated.

Screen Saver Run Time →�
�� 10 min / 20 min / 40 min / 1 hour
Select to set the waiting time before the screen saver appears.

Information
Select to viewing the information of the connected device.

Remove Safely
You can remove the device safely from the TV.
English - 36
BN68-01939A-Eng.indd 36
2009-04-15 오후 2:54:54
Media Play-DLNA
Setting the DLNA Network
DLNA allows you to watch videos and pictures saved on your PC on your TV through a network connection in Media Play mode.
This removes the need to copy them to a USB storage device and then connect the device to your TV. To use DLNA, the TV must be
connected to the network and the DLNA application must be installed on your PC.
❑ Network Connections Diagram
PC
TV
LAN
LAN
External Modem
(ADSL/VDSL/Cable TV)
1
3
2
1. Connect the LAN port on the rear panel of the TV to the external modem with a LAN Cable.
2. Connect the PC to which the “DLNA PC Share Manager” programme will be installed and the external modem using a LAN cable.
3. Connect the LAN port on the wall and the external modem with a Modem Cable.
❑ Connecting to the Network
1. When connecting to the network is complete, set up the network on the TV.
N A Wireless Internet connection does not support DLNA.
N Three parts(subnet address) before the TV and PC IP addresses should be same. The last part (host address) should be
changed. (e.g. IP Address: 123.456.789.** )
2. Run a Network Test to check the network settings.
Installing the DLNA Application
To play content on the PC on the TV, you have to first install the application.
 System Requirements
1. Insert the Programme CD supplied with this TV into your PC.
2. 20MB of free hard disk space is needed for the programme installation.
N If you share files, up to 20MB of hard disk drive space is required for each 100 files.
N If you cancel file sharing, the hard disk drive space used for the thumbnail information is also freed.
 Supported Formats
1. Image: JPEG (jpg, jpeg)
2. Audio: MP3 (mp3)
3. Video: MPEG1(mpg, mpeg), MPEG2 PS/TS(mpg, mpeg, trp, ts, tp), divx(mpg, mpeg, avi), MPEG4/H.264 (mpg, mpeg)
Continued...
English - 37
BN68-01939A-Eng.indd 37
2009-04-15 오후 2:54:55

Install the application
1. Run the Setup.exe file on the Programme CD supplied with the product.
N Alternatively, you can download the file from www.samsung.com.
2. Install the SAMSUNG PC Share Manager as shown in the figures below.
►
►
►
►
►
3. When the installation is complete, the PC Share Manager icon appears on your Desktop.
N Double-click the icon to run the programme.
English - 38
BN68-01939A-Eng.indd 38
2009-04-15 오후 2:54:56
Using the DLNA Application
The Programme Screen Layout
1
2
3
4
8
5
6
1.
2.
3.
4.
5.
6.
7.
8.
7
Menus: The following application menus are provided : File, Share, Server, and Help.
Click to share the selected PC server folder.
Click to cancel sharing.
Click to refresh the PC folder and files.
Click to synchronize the share status.
The folders and files of the PC to be shared are listed.
Folders shared by the user are listed.
PC server name shown on the device list of the Media Play: Click to change the name.
❑ File
 Property: Shows information on the selected file or folder.
• Method 1: Select a file or folder and select the File menu and then select the Property sub-menu.
• Method 2: Select a file or folder, right-click over the selected file or folder and then select Property from the pop-up menu.
<Method 1>
Name
Name
Name
Name
<Method 2>
Name
Name
Name
Name
Name
Name
Name
Name
Modified
Modified
Modified
Modified
 Exit: Exits the DLNA application.
If you select Exit without applying the changes after changing the shared status, a message will appear asking if you want to apply
the changed settings to the PC. Select Yes to apply the changes and exit the application.
Name
Name
Name
Name
Yes
Yes
Yes
Yes
No
No
No
No
Continued...
English - 39
BN68-01939A-Eng.indd 39
2009-04-15 오후 2:54:57
❑ Share
 Sharing a Folder
You can share a folder from your PC to the TV. The maximum number of folders that can be shared is 32.
N Your PC will operate as a server to the TV.
• Method 1: Select a folder in My Computer, select the Share menu and then select the Share Folder sub-menu.
• Method 2: Select a folder in My Computer, right-click over the selected folder and then select Share Folder from the pop-up
menu.
• Method 3: Locate the mouse pointer over a folder in the My Computer folder list in the left pane and drag&drop the folder into
the Shared Folders pane. If a message appears asking you to confirm the shared folder, select Yes.
<Method 1>
<Method 2>
<Method 3>
 Cancelling a Shared Folder
You can cancel a shared folder on your PC. Select a folder from the Shared Folder pane and select Unshare Folder.
• Method 1: Select a folder from the Shared Folder pane, select the Share menu and then select Unshare Folder.
• Method 2: Select a folder from the Shared Folder pane, right-click over the selected folder and then select Unshare Folder
from the pop-up menu.
• Method 3: Locate the mouse pointer over a folder in the Shared Folder pane and drag&drop the folder into the My Computer
pane. If a message appears asking you to confirm the cancelation, select Yes.
<Method 1>
<Method 2>
<Method 3>
 Applying the Current Settings
Perform this when synchronization is necessary due to a new shared folder or canceling a shared folder. The Set Changed State
menu applies changes to shared folders to the data saved with the PC share programme.
Since applying changes to the internal data is a time-consuming process, this function enables users to apply changes to the data
only when required.
Until the Set Changed State menu is selected, the changed state of the shared folder is not applied to the server.
Changes to the shared folders are not applied to your PC until you select the Set Changed State menu.
• Method 1: Select the Share menu and select the Refresh DB sub-menu.
• Method 2: Click the Set Changed State icon.
Continued...
English - 40
BN68-01939A-Eng.indd 40
2009-04-15 오후 2:54:58
 Setting the Access Permission
To enable the TV to find your PC, the TV must be set to Set Device Policy in the Access Permission Settings window. In addition,
the PC server and the TV must be on the same subnet.
• Method: Select the Share menu and select Set Device Policy. Rejected items are represented in gray. You can change the
access permissions by using the Allow Accept / Deny button. To delete an item, select the item and select Delete Item.
❑ Server
 Server
You can run or stop using your PC as a server.
 Start Server at Windows start
You can determine whether to start the PC server automatically when Windows starts.
 Change server name
You can rename the PC server. Enter a new name and click OK. The new name will appear at the top right of the window and will
appear on the TV.
❑ Help
 Version
The programme version information message box appears.
English - 41
BN68-01939A-Eng.indd 41
2009-04-15 오후 2:54:58
Using the DLNA Function
Using the DLNA Menu
DLNA (Digital Living Network Alliance) enables content saved on a DLNA server
(usually your PC) connected to your TV or over a network to be played.
Media Play
Media Play enables playing content saved on a USB memory device connected to the
TV, while DLNA enables playing content saved on a DLNA server (your PC) connected
to your TV or over the network. The procedures to use the content are the same as
those for Media Play.
If you install the PC share manager programme supplied with the TV onto a PC, you
can have the PC perform the role of a DLNA server over the network.
USB : USB
851.98MB/995.00MB Free
PHOTO
Photo
USB
Music
Movie
Setup
Return
 Device
1. Press the MEDIA.P button on the remote control to display the DLNA menu.
2. Press the ◄ or ►button to select an icon (Photo, Music, Movie, Setup), then press the ENTERE button.
N To exit DLNA mode, press the MEDIA.P button on the remote control.
❑ Photo

Photo List Tools menu
Slide Show / Copy / Play Current Group / Change Group / Copy Current Group / Information

Slide Show Tools menu
Stop Slide Show & Start Slide Show / Slide Show Speed / Slide Show Effect / Zoom / Rotate / Picture Setting / Sound Setting /
Information
❑ Music

Music List Tools menu
Play Current Group / Copy / Change Group / Information

Music Play Tools Menu
Repeat Mode / Picture Setting / Sound Setting / Information
❑ Movie

Movie List Tools menu
Play Current Group / Copy / Copy Current Group / Information

Movie Play Tools Menu
Picture Setting / Sound Setting / Picture Size / Caption / Information
❑ Setup
Use Colour View / Music Repeat Mode / Cont. movie play help / Get the DivX® VOD registration code / Get the DivX® VOD
deactivation code / Screen Saver Run Time / Information
N DLNA does not support the following functions.
-
The Background Music and Background Music Setting functions.
Sorting files by preference in the Photo, Music, and Movie folders.
The Change Group function.
The Safe Remove function.
The
(�����
REW)/
(����������������������������������������������
FF) button functions while a movie is playing.
N The Skip (◄/► button) or Pause function may not work while a movie is playing for the DLNA of other manufacturers,
depending on the corresponding content information.
N The playing time may not be displayed while a movie is playing.
English - 42
BN68-01939A-Eng.indd 42
2009-04-15 오후 2:54:58
Content Library
Activating the Content Library
1. Press the MENU button. Press the ▲ or ▼ button to select Application,
then press the ENTERE button.
2. Press the ▲ or ▼ button to select Content Library, then press the ENTERE
button. The Content Library main menu is displayed.
Media Play (USB & DLNA)
Anynet+ (HDMI-CEC)
Application
The Content Library enables you to view or play the built-in contents on the TV or stored
on your USB device. The Delete, Move and Update functions will not work with the
built-in content on the TV.
Content Library
Internet@TV
Home Network Centre
O Press the CONTENT button on the remote control to display the
Content Library main menu.
3. Press the ◄ or ► button to select an icon (Gallery, Cooking, Children, Wellness,
Others, Content Management), then press the ENTERE button.
Content Library
N The selected item will be run.
Gallery
<
Gallery
Cooking
Children
Wellness
Others
Return
>
Exit
❑ Using the Remote Control Button in Content Library Menu
Button
Operations
▲/▼/◄/►
Move the cursor and select an item.
ENTERE
Select the currently selected item.
RETURN
EXIT
P
Return to the previous menu.
Stop the current function and return to the Content Library main menu.
Stop Content Library mode and Returns to TV mode.
You can control the volume of the played content.
CONTENT
Exit Content Library mode.
N If you press the Volume or MMUTE button, no OSD is displayed, but the function operates accordingly.
N To return to TV mode, press the P
button on the remote control.
N CONTENTS LIBRARY CONTAINS TEXT, GRAPHICS, IMAGES, MULTIMEDIA, AND OTHER MATERIALS FOR
INFORMATIONAL AND PROMOTIONAL PURPOSES ONLY. MATERIALS IN CONTENTS LIBRARY HAS BEEN
MODIFIED AND KEEPS BEING REVISED AND UPDATED. THE MATERIALS IN THE CONTENTS LIBRARY MAY NOT
BE SUITABLE FOR ALL AUDIENCES.
N INFORMATION IN THE CONTENTS LIBRARY IS PROVIDED “AS IS.” ALTHOUGH THE INFORMATION PROVIDED
TO YOU IN THE CONTENTS LIBRARY IS OBTAINED OR COMPLIED FROM SOURCES WE BELIEVE TO BE
RELIABLE, SAMSUNG CANNOT AND DOES NOT GUARANTEE THE ACCURACY, VALIDITY, TIMELINESS OR
COMPLETENESS OF ANY INFORMATION OR DATA MADE AVAILABLE TO YOU FOR ANY PARTICULAR PURPOSE.
UNDER NO CIRCUMSTANCES, INCLUDING NEGLIGENCE, SHALL SAMSUNG BE HELD LIABLE, WHETHER IN
CONTRACT OR TORT, FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES,
ATTORNEY FEES, EXPENSES, OR ANY OTHER DAMAGES WHATSOEVER ARISING OUT OF, OR IN CONNECTION
WITH, ANY INFORMATION CONTAINED IN, OR THE USE OF, THE CONTENTS LIBRARY, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
English - 43
BN68-01939A-Eng.indd 43
2009-04-15 오후 2:54:59
Using the Content Library
❑ Gallery�
This function plays a Slide Show with high resolution images and background music and pro­duces various atmospheres.
Using the Gallery function of the TV, you can change your home at­mosphere.
N Press INFO button to see the credit and detail information in English for the imagery.
Press INFO button again or press ► button for the credit information to go away (currently, the credit supports English only).
N The copyrights of the Gallery contents and all issues related to them are reserved by Gallery Player, Inc.
N For additional Gallery contents, check for information through www.samsung.com. Please refer to the Using Additional
Content Using External USB Memory Storage section to see how to play additional imagery.
❑ Cooking
You can view various recipes that you can then easily follow step by step. Enjoy these contents which give you great ideas for
meals.
N The recipes introduced in the Cooking contents on the Samsung TV are based on recipes published by Anness Publishing.
N The copyrights of the Cooking contents and all issues related to them are reserved by Practical Pictures.
❑ Children
This is educational and interactive content that children can watch repeatedly. Enjoy existing stories, songs and plays with the
Boowa and Kwala characters.
N The copyrights of the Children contents and issues related to them are reserved by UpToTen.
❑ Wellness�
This is beneficial health management content that provides stretching and massage exercises that can be enjoyed by the whole
family.
N The copyrights to the Relaxing sound content are reserved by Practical Pictures. All issues related to copyrights are reserved
by the corresponding company.
❑ Others
The default content is not saved in the TV memory.
N You can copy new content to the TV memory using the Content Management screen.
❑ Content Management
You can download contents onto a USB memory and play them on your TV.
My contents
The use of contents is the same as in using the TV memory contents. Also, you can delete and play the each contents.
 USB

You can download the contents onto a USB memory device and play them on your TV. (The contents on the external USB device
are played directly without being copied to the built-in Flash memory of the TV.)
����������
N Content Library only supports USB Mass Storage Class devices (MSC). MSC is a Mass Storage Class Bulk-Only Transport
device. Examples of MSC are Thumb drives and Flash Card Readers (Both USB HDD and HUB are not supported.)
N Playing a game using an external USB memory device will allow you to save your game (depending on the game).
Take care as removing the USB memory device while saving data to the USB memory device may cause the data to be lost.
N Downloading New Contents
New content other than the built in content will be provided via the the Samsung.com website free of change.
When you download the paid contents, you need UDN number to download contents.
Check the UDN number before downloading a new content item.
1. Visit the www.samsung.com website
2. Select a content item in the Contents Download page.
3. Download the contents onto the USB memory device.
4. Go to Content Library main menu by pressing CONTENT button or choosing Content Library
(Menu ��������������������������������
→�������������������������������
Application ������������������
→�����������������
Content Library)
5. Plug the USB memory into USB port on the side of the TV.
6. You can see the content sub item which you downloaded.
7. Select a content item and press the enter button.
8. You can play the selected content item or copy it to the TV memory.

Setup
• Screen Saver Run Time → 10 min. / 20 min. / 40 min. / 1 hour
Select to set the waiting time before the screen saver appears.
• Save UDN (Unique Device Number)
The 18-digit number on the screen is the product code.
You can save the UDN to your USB memory.
English - 44
BN68-01939A-Eng.indd 44
2009-04-15 오후 2:54:59
Network
Network Connection
❑ Network Connection - Cable

LAN Connection for a DHCP Environment
The procedures to set up the network using Dynamic Host Configuration Protocol (DHCP) are described below.
Since an IP address, subnet mask, gateway, and DNS are automatically allocated when DHCP is selected, you do not have to enter
them manually.
TV Rear Panel
The Modem Port
on the Wall
External Modem
(ADSL/VDSL/Cable TV)
1 LAN Cable
2 Modem Cable
1. Connect the LAN port on the rear panel of the TV and the external modem with a LAN Cable.
2. Connect the LAN port on the wall and the external modem with a Modem Cable.
You can connect the LAN via a Sharer (Router).
IP Sharer
The Modem Port
on the Wall
External Modem
(ADSL/VDSL/
Cable TV)
LAN Cable
TV Rear Panel
LAN Cable
Modem Cable
You can connect the LAN port and the TV directly depending on your network status.
TV Rear Panel
The LAN Port
on the Wall
LAN Cable
N The terminals (the position of the port and the type) of the external device may differ depending on the manufacturer.
N If the IP address allocation by the DHCP server has failed, turn the external modem off, turn it on again after at least 10 seconds
and then try again.
N For the connections between the external modem and the Sharer (Router), refer to the owner’s manual of the corresponding
product.
N You can connect the TV to the LAN directly without connecting it through a Sharer (Router).
N You cannot use a manual-connection-type ADSL modem because it does not support DHCP. You have to use an automatic-
connection-type ADSL modem.
Continued...
English - 45
BN68-01939A-Eng.indd 45
2009-04-15 오후 2:55:01

LAN Connection for Static IP Environment
The procedures to set up the network using a static IP address are described below. You have to manually enter the IP address,
subnet mask, gateway, and DNS that are provided by your Internet Service Provider (ISP).
TV Rear Panel
The LAN Port
on the Wall
1 LAN Cable
1. Connect the [LAN] port on the rear panel of the TV and the LAN port on the wall using the LAN cable.
You can connect the LAN via a Sharer (Router).
The LAN Port
on the Wall
IP Sharer
LAN Cable
TV Rear Panel
LAN Cable
N The terminals (the position of the port and the type) of the external device may differ depending on the manufacturer.
N If you are using a static IP address, your ISP will inform you of the IP address, subnet mask, gateway, and DNS.
You must enter these values to complete the network settings. If you do not know the values, ask your network administrator.
N For the information on how to configure and connect a Sharer (Router), refer to the owner’s manual for the corresponding
product.
N You can connect the TV to the LAN directly without connecting it through a Sharer (Router).
N If you use an IP Sharer (IP Router) that supports DHCP, you can set up the device as either DHCP or static IP.
N For the procedures to use a static IP address, ask your Internet Service Provider.
Continued...
English - 46
BN68-01939A-Eng.indd 46
2009-04-15 오후 2:55:03
❑ Network Connection - Wireless
You can connect to the network wirelessly through a wireless IP sharer.
TV Side Panel
The LAN Port
on the Wall
Samsung Wireless LAN
Adapter
Wireless IP sharer
LAN Cable
1. Connect the ‘Samsung Wireless LAN Adapter’ into the USB1(HDD) or USB2 terminal of the TV.
N You must use the ‘Samsung Wireless LAN Adapter to use a wireless network.
N Samsung’s Wireless LAN adapter is sold separately. The WIS09ABGN Wireless LAN adapter is offered by select retailers,
Ecommerce sites and Samsungparts.com.
N To use a wireless network, your TV must be connected to a wireless IP sharer. If the wireless IP sharer supports DHCP, your TV
can use a DHCP or static IP address to connect to the wireless network.
N Samsung’s Wireless LAN adapter supports IEEE 802.11A, IEEE 802.11B, IEEE 802.11G, IEEE 802.11N. When you play DLNA
video over IEEE 802.11B/G connection, the video may not be played smoothly.
N If the wireless IP sharer allows you to turn the Ping connection function on/off, turn it on.
N Select a channel for the wireless IP sharer that is not currently being used. If the channel set for the wireless IP sharer is
currently being used by another device nearby, this will result in interference and communications may fail.
N If you apply a security system other than the systems listed below, it will not work with the TV.
- When applying the security key for the AP (wireless IP sharer), only the following is supported.
1) Authentication Mode : OPEN, SHARED, WPAPSK, WPA2PSK
2) Encryption Type : WEP, TKIP, AES
- When applying the security key for the Ad-hoc mode, only the following is supported.
1) Authentication Mode : SHARED, WPANONE
2) Encryption Type : WEP, TKIP, AES
N If your AP supports WPS(Wi-Fi Protected Setup), you can connect to the network via PBC (Push Button Configuration) or PIN
(Personal Indentification Number). WPS will automatically configure the SSID and WPA key in either mode.
N If the device isn’t certified, it may not connect to the TV via the ‘Samsung Wireless LAN Adapter’.
English - 47
BN68-01939A-Eng.indd 47
2009-04-15 오후 2:55:04
Network Setup
❑ Network Type
Select Cable or Wireless as the method to connect to the network.
N The menu is activated only if the ‘Samsung Wireless LAN Adapter’ is connected.
���������������������������������
to network using a cable.
• Cable: Connect
������������������������������
to network wirelessly.
• Wireless: Connect
Setup
❑ Network Setup
BD Wise
: Off
Network Type
: Cable
Network Setup
Child Lock
►
: On
Cable Network Setup
Change PIN
(when Network Type is set to Cable)
Melody
: Medium
Energy Saving
: Off
�� Auto / Manual
• Internet Protocol Setup →�
PIP
�����������������������������������������������������������������������
can test or confirm the network connection status after setting up
• Network Test: You
the network.
N When unable to connect to a wired network
If your Internet service provider has registered the MAC address of the device used to connect to the Internet for the first time
and authenticates the MAC address each time you connect to the Internet, your TV may not be able to connect to the Internet
as the MAC address differs from that of the device (PC).
In this case, ask your Internet service provider about the procedures to connect devices other than your PC (such as your TV)
to the Internet. If your Internet service provider requires an ID or password to connect to the Internet (network), your TV may not
be able to connect to the Internet. In this case, you have to enter your ID or password when connecting to the Internet using an
Internet Sharer (Router).
The internet connection may fail due to a firewall problem. In this case, contact your Internet service provider. If you cannot
connect to the Internet even if you have followed the procedures of your Internet service provider, please contact a Samsung
Electronics.

❑ Cable Network Setup

Cable Network Setup-Auto Setup
If you connect the LAN cable and it supports DHCP, the Internet Protocol (IP) Settings are automatically configured. (See page 45)
1. Set Network Type to Cable.
2. Select Cable Network Setup.
3. Set Internet Protocol Setup to Auto.
N The Internet Protocol is set automatically.
4. Select Network Test to check the network connectivity.

Cable Network Setup-Manual Setup
To connect the TV to the LAN using a static IP address, you must set up the Internet Protocol (IP).
N Please check if the LAN cable is connected. (See page 45)
1. Set Network Type to Cable.
2. Select Cable Network Setup.
3. Set Internet Protocol Setup to Manual.
4. Set up IP Address, Subnet Mask, Gateway and DNS Server.
N Press the number buttons on the remote control when you set the Network manually.
5. Select Network Test to check the network connectivity.
❑ Wireless Network Setup
N The menu is activated only if the ‘Samsung Wireless LAN Adapter is connected. (See page 50)
• Internet Protocol Setup →�
�� Auto / Manual
• Network Test: You can test or confirm the network connection status after setting up the network.
N When unable to connect to an AP
Your TV may fail to locate an AP that is configured as a private SSID type. In this case, please change the AP settings and try
again. If your Internet service provider has registered the MAC address of the device used to connect to the Internet for
the first time and authenticates the MAC address each time you connect to the Internet, your TV may not be able to connect to
the Internet as the MAC address differs from that of the device (PC).
In this case, ask your Internet service provider about the procedures to connect devices other than your PC (such as your TV)
to the Internet. If you cannot connect to the Internet even if you have followed the procedures of your Internet service provider,
please contact a Samsung Electronics.
Continued...
English - 48
BN68-01939A-Eng.indd 48
2009-04-15 오후 2:55:04

Select a network
- Access Point: You can select the IP sharer to use when using a wireless network.
N If a wireless network is not in the Select a network list, press the Red button.
N When the connection is made, you will be returned to the screen automatically.
N If you have selected an Access Point with a security authentication:
Wireless* Network*Setup
A
The Security Key input screen appears. Enter the security key and press the Blue
button on the remote control.
N If security encryption type is WEP, 0~9, A~F will be available when you input
security key.
Button
Moves the selection up/down/left/right.
ENTERE
Enters (Inputs) the selected character.
Green button
Blue button
B
C
D
n Move
E
F
0~9 *
*
*
*
*
Number
Delete
Done
Number E Enter R Return
Operations
▲/▼/◄/►
Red button
_
Security
* Key
Switch between Upper- and Lower-Case Letters
You can delete an already entered character.
Press this button to finish entering the security key.
❑ Connecting WPS (Wi-Fi Protected Setup)

If Security Key is already set: In access point list, select WPS.
N You can select PBC, PIN, Security Key.
Wireless* Network Setup
Select* a* network
• Connecting by using PBC: Select a PBC (Push Button Configuration). Press the
PBC button on the AP (access point) within 2minutes, and wait for connection.
• Connecting by using PIN: Select a PIN (Personal Identification Number).
N The message showing the PIN Code is displayed. Input the PIN Code at AP
device within 2minutes. Select OK and wait for connection.
N Try again if connecting operation doesn’t work
N When the connection is not established although tried again, reset the access
point. Please refer to a manual of each access point.
• Connecting by using Security Key: When selecting Security Key, the input window is
displayed. Input the security key and press Blue button.
N Try again if connecting operation doesn’t work.

If Security Key is not set: When the security setting of AP that supports WPS
is NONE, you can select PBC, PIN, None Security. None Security is capable of
connecting to AP directly without using WPS function.
N Process of PBC, PIN is same as above. Refer to if Security Key is already set.
N Try again if connecting operation doesn’t work.
*
Search
*
Ad-hoc
3/9
sson
jee
AP_1
Ap_2
PBC
PIN
Security Key
*
n Move E Enter R Return
Press the PBC button on the access point.
* : AP_1
Access Point Name
Cancel
Press OK After input TV’s Pincode in the access
point’s setup.
Access Point Name : AP_1
PIN Code : 12345678
Cancel
OK
Wireless* Network*Setup
_
Security
* Key
A
H
O
V
B C
I J
P Q
W X
*
D
K
R
Y
n Move
E
L
S
Z
F
M
T
G
N
U
0~9 *
*
*
*
*
Number
Lowercase
Delete
Done
Number E Enter R Return
Wireless* Network Setup
Select* a* network
*
Search
*
Ad-hoc
3/9
sson
jee
AP_1
Ap_2
PBC
PIN
Security Key
*
n Move E Enter R Return
Continued...
English - 49
BN68-01939A-Eng.indd 49
2009-04-15 오후 2:55:05

Ad-hoc: You can connect to a mobile device without an access point through the ‘Samsung Wireless LAN Adapter’ by using
a peer to peer network.
• How to connect to new Ad-hoc
1. Choose Select a network, then a device list is displayed.
2. While in the device list, press the Blue button on the remote or select Ad-hoc.
The existing network system may have limited
functionality. Do you want to change the network
N The message The existing network system may have limited functionality.
connection?
Do you want to change the network connection? is displayed.
Yes
3. Input the generated Network Name(SSID) and Security Key into the device you
want to connect.
• How to connect an existing Ad-hoc device
1. Choose Select a network, the device list is displayed.
*
2. Select the device you want in the Device list.
3. If security key was applied, input the security key again.
N If network doesn’t operate normally, please check the Network Name(SSID) and Security Key again.
If the Security Key is incorrect, it may be the reason for the malfunction.

No
Wireless Network Setup - Auto Setup
If you want to connect AP, AP should support DHCP.
Only devices which support Ad-hoc mode can be connected without DHCP.
1. Set Network Type to Wireless.
2. Select Wireless Network Setup.
3. Set Internet Protocol Setup to Auto.
N The Internet Protocol is set automatically.
4. Select a network through Select a network.
5. Select Network Test to check the network connectivity.

Wireless Network Setup - Manual Setup
To connect the network wirelessly using a static IP address, you must set up the Internet Protocol (IP). (See page 47)
N For more detailed information of static IP address, refer to the user manual of your wireless IP sharer.
1. Set Network Type to Wireless.
2. Select Wireless Network Setup.
3. Set Internet Protocol Setup to Manual.
4. Set up IP Address, Subnet Mask, Gateway and DNS Server.
N Press the number buttons on the remote control when you set the Network manually.
5. Select a network through Select a network.
6. Select Network Test to check the network connectivity.
English - 50
BN68-01939A-Eng.indd 50
2009-04-15 오후 2:55:05
Internet@TV
N This function may not be supported depending on your country.
N If you have some problems while using a widget service, please contact to service provider.
In the widget, press the green button and get contact information or refer to help website for service provider information.
N English may be only supported in widget service depending on region.
Getting Started with Internet@TV
Internet@TV provides SAMSUNG’s widget services through a network connection. Internet@TV contents can be changed depending
on contents provider. You can access various information such as YouTube, through the Internet@TV service.
N If a certain content's font provided by contents provider is not supported on TV, It may not be viewed normally.
N The configuration of Widgets and their provided services may differ according to the selected country. After changing country, turn
off and on the TV. Then you can use widget service supported changed country. If Country is set to Others, TV can’t recognize your
country. In this case, please select directly from the service country list.
N For more information on how how to configure your country, refer to the ‘Plug & Play Feature’ instructions.
N You may experience slow operation or hesitation when using this function due to network conditions.
N Before using Internet@TV, set up the network first. For more information on how to configure your network, refer to ‘Network
Setup’.
When running Internet@TV for the first time, the basic settings proceed automatically. It may take few minutes to update.
1. Press the MENU button. Press the ▲ or ▼ button to select Application, then press the ENTERE button.
2. Press the ▲ or ▼ button to select Internet@TV, then press the ENTERE button.
O Press the INTERNET@ button on the remote control to display the Internet@TV
menu.
3. The User Agreement is displayed. Select Agree to accept the agreement.
4. The Statistics & Analysis is displayed. Select Agree to accept the agreement.
Setting up Internet@TV
You can check and use the menus regarding Single Sign On (SSO), system management and properties.
Press the ▲ or ▼ button to select Setup, then press the ENTERE button.
❑ Single Sign On
You can use this menu when creating, deleting the account.
Using the Single Sign On, you can control your account including contents site’s account information.
You don’t need additional log in.
N Account is only for internet@TV.

Create Account
You can create account and be linked with desired service site.
N Account will be made less than 10.
N Character of Account should be limited to 10.
N If there is no service that needs log in, you can not create account.

Account Management
• Service Site: You can register log in information of service site (such as YouTube).
• Change Password: Change the password of your account.
• Delete: Delete the account.
N If you forget the password of account, press the remote control buttons in the following sequence, which resets the
Internet@TV: POWER (off) → MMUTE → 9 → 4 → 8 → POWER (On).
If you use this function, all accounts will be deleted.
Continued...
English - 51
BN68-01939A-Eng.indd 51
2009-04-15 오후 2:55:05
❑ System Setup
N Ticker Autorun, Ticker Duration may not be supported depending on country.

Change the Service Lock password
N The default password number of a new TV set is ‘0-0-0-0’.
N If you forget the password, press the remote control buttons in the following sequence, which resets the password to ‘0-0-0-0’:
POWER (Off) ��
→� MMUTE →� 8 →� 2 →� 4 →� POWER (On).

Service Duration
Select to set the service duration time before the screen saver appears.

Ticker Autorun →�
�� Off
������/ On
��
Select to set ticker to run automatically or not when turning on the TV.

Ticker Duration
Select to set the service duration time before the screen saver appears.
❑ Properties
Display information of Internet@TV.
You can measure the speed of your Internet TV service using Measuring the speed of the Internet TV service.
Using the Internet@TV service
In a widget that provides multiple category menus, you can view the contents of the category menus using the ◄ and ► buttons.
 Account Login
1. Press the Red button.
2. Select desired User account, then press the ENTERE button.
3. Input the password.
N When login succeeds, User account will be displayed on the screen.
N Before login, at least one and more account should be registered. If you want to create account, refer to ‘Setting up Internet@
TV’.

Using the Widget Gallery
You can use Run Service, Lock, Install Service at the existing widget and you can see description of the widget service that isn’t
installed.
On the Internet@TV, you can add and use various widgets provided by service provider. It may vary according to contents provider.
• Run Service: Runs the widget service.
• Lock: Set the service lock
• Install Service (or Delete Service): Install or delete widget service.

Using the YouTube Widget
You can watch the movie provided by YouTube.
If you have the account in YouTube, Register account information using Account
management. Then, you can use My Favourites category.
N The menu can be changed by web service.
N There may be inappropriate contents for child. In this case, use Lock function in
Widget Gallery.
_zol„
Xz~*atp‚po
_z{*]lpo
Xz~*[z{€wl}
Xz~*Ot~n€~~po
_z{*Qlz€}tp~
Xz~*Wtyvpo
Xz~*]p~{zxopo
Qpl€}po
^ppvtyr*U€~tnp*Opnlop~*Wlp}
;E;<E>;
<:B
atp‚~*E*C<D7=@=****************]ltyr*E
=;;D8;=8;B
M}plvtyr*Yp‚~*Lwp}~*m„*P8Xltw
;E;;E?@
atp‚~*E*C<D7=@=****************]ltyr*E
=;;D8;=8;B
_sp*‚z}wo*}pln~*z*`9^9*mltwz€*{wly
;E;<E>;
atp‚~*E*C<D7=@=****************]ltyr*E
=;;D8;=8;B
Mzz*Szz*ty*sp*Mzl}o}zzx
;E;>E=A
atp‚~*E*C<D7=@=****************]ltyr*E
=;;D8;=8;B
 Change Mode llrrChange pageU Move E OKR Return
English - 52
BN68-01939A-Eng.indd 52
2009-04-15 오후 2:55:05
Troubleshooting for internet@TV
Problem
Possible Solution
Some widget services do not work.
Check with that service provider.
In the widget, press the green button and get contact information or refer to help website
for widget service provider information.
Refer to Help website page.
What is the advantage of single sign
on?
If you create account and register your login information of desired service, you can
access personalized content without additional login.
When a network error occurred, I can’t
use other menus except setting menu.
If network connection doesn’t work, your service might be limited.
Because all widgets except setting widget(Profile widget, Widget Gallery) need to connect
internet.
Is there any possibility to show adult
movies on YouTube?
Basically, at the list on the menu it is filtered out. But by using search function, It can be
shown. In this case, using the Widget Gallery lock the widget service.
Help Website
Country
Israel
Iran
Website
www.samsung.com → Consumer Products→ TV → medi@2.0 → Internet@TV
www.samsung.com →
→
→ medi@2.0 → Internet@TV
Saudi Arabia
www.samsung.com → Products → television → medi@2.0 → Internet@TV
UAE
www.samsung.com → Consumer → television → medi@2.0 → Internet@TV
Australia
www.samsung.com → Consumer → television → medi@2.0 → Internet@TV
China
www.samsung.com → 个人消费产品 → 电视产品 → medi@2.0 → Internet@TV
HongKong
www.samsung.com → consumer products → Televisions → medi@2.0 → Internet@TV
HongKong
www.samsung.com → 個人消費産品 → 電視 → medi@2.0 → Internet@TV
India
Indonesia
www.samsung.com → consumer products → television → medi@2.0 → Internet@TV
www.samsung.com → Produk → television → medi@2.0 → Internet@TV
Japan
www.samsung.com → 製品情報 → 液晶ディスプレイ → medi@2.0 → Internet@TV
Korea
www.samsung.com → 제품정보 → TV → medi@2.0 → Internet@TV
Malaysia
www.samsung.com → Consumer → television → medi@2.0 → Internet@TV
NewZealand
www.samsung.com → Consumerv → television → medi@2.0 → Internet@TV
Philippines
www.samsung.com → Consumer → television → medi@2.0 → Internet@TV
Singapore
www.samsung.com → Consumer → television → medi@2.0 → Internet@TV
Taiwan
www.samsung.com → 個人消費産品 → 電視 → medi@2.0 → Internet@TV
Thailand
www.samsung.com → ผลิตภัณฑ์ → โทรทัศน์ → medi@2.0 → Internet@TV
Vietnam
www.samsung.com → sản phẩm nghe nhìn → máy thu hình → medi@2.0 → Internet@TV
South Africa
www.samsung.com → Consumer → television → medi@2.0 → Internet@TV
N Approaching step may be changed later on.
N It can be different links for special countries.
English - 53
BN68-01939A-Eng.indd 53
2009-04-15 오후 2:55:06
Home Network Centre
Home Network Centre
About the Home Network Centre
The Home Network Centre connects the TV and mobile phones through a network. You can view call arrivals, text message contents,
and schedules set on the mobile phone on the TV using the Home Network Centre. In addition, you can play the media contents saved
on the mobile phones such as videos, photos and music by controlling them onto the TV via the network.
N If the device supports DLNA DMC (Digital Media Controller) function, Home Network Centre function is available.
N The Samsung SCH-i900 mobile phone supports the Home Network Centre. Other models will be added in the future. The mobile
device may need additional software installation. For details, refer to each user’s guide.

Connecting to the Home Network Centre
For more information about the network settings, refer to ‘Network Setup’.
• Connecting to a Wi-Fi Ad-hoc network
TV Side Panel
Mobile phone
Samsung Wireless
LAN Adapter
or
1. Connect the ‘Samsung Wireless LAN Adapter’ to the USB1(HDD) or USB2 port of the TV.
2. For more information on how to configure Ad-hoc network, refer to ‘Network Setup’.
N For information on configuring the mobile phone’s network settings, refer to the mobile phone manual.
3. Set up the IP address, SSID and password for the mobile phone in the Ad-hoc Settings of the mobile phone using the
Network Name (SSID) and Security Key (password) displayed on the TV.
• Connecting through a wire / wireless IP sharer
1. Connect the LAN port of the TV and the Wire/Wireless IP sharer using the LAN cable or connect the USB1(HDD) or USB2
port of the TV and the ‘Samsung Wireless LAN Adapter’.
N For the procedures to set up the wire/wireless sharer and the mobile phone, refer to the manual of the corresponding
device.
TV Side Panel
Mobile phone
Wire/Wireless IP sharer
Samsung Wireless
LAN Adapter
or
LAN Cable
TV Side Panel
Mobile phone
Wire/Wireless IP sharer
Samsung Wireless
LAN Adapter
or
LAN Cable
English - 54
BN68-01939A-Eng.indd 54
2009-04-15 오후 2:55:09
Setting Up the Home Network Centre
❑ Message
Shows a list of mobile phones which have been set up with this TV to use the
message function (the call arrivals, text message contents and schedules set on the
mobile phone).

Allowed
Allows the mobile phone.

Denied
Blocks the mobile phone.

Delete
Deletes the mobile phone from the list.
N This function just deletes the name from the list. If the deleted mobile device
turns on or tries to connect to the TV, it may be shown on the list.
Home Network Centre
Message
111-1234-5671
: Access
Media
111-1234-5672
: Access
Setup
111-1234-5673
: Denied
111-1234-5674
: Denied
Return
Exit
❑ Media
Shows a list of mobile phones which is available to control media contents
(videos, photos, music) from the phone.
N Besides mobile phone, other mobile devices that support DLNA DMC are
available.

Allowed
Allows the mobile phone.

Denied
Blocks the mobile phone.

Delete
Deletes the mobile phone from the list.
N This function just deletes the corresponding name on the list. If the deleted
mobile device turns on or tries to connect to the TV, it may be shown on the list.
Home Network Centre
Message
111-1234-5671
: Access
Media
111-1234-5672
: Access
Setup
111-1234-5673
: Denied
111-1234-5674
: Denied
Return
❑ Setup

Message → On / Off
You can determine whether to use the message function (the call arrivals, text
message contents, and schedules set on the mobile phone).

Media → On / Off
You can select whether to use the play function that Media the contents (videos,
photos, music) from the mobile phone.

TV name
You can set the TV name so as to find it easily on the mobile device.
N If you selects User Input, you can type the TV name by OSK(On Screen Keyboard).
Exit
Home Network Centre
Message
Message
: On
Media
Media
: On
Setup
TV name
: TV
Return
Exit
English - 55
BN68-01939A-Eng.indd 55
2009-04-15 오후 2:55:13
Using the Message Function
Using this function, you can view the call arrivals, text message contents and
schedules set on the mobile phone through the alarm window while watching TV.
husband
SMS
N To disable this Message alarm window, set Message to Off in Setup of the Home
N
N
N
N
Network Centre.
The alarm window appears for 20 seconds. If no key is pressed or if Cancel is
selected, it appears up to three times at 5 minute intervals.
If OK is selected, or if OK is not selected while the message is displayed three
times, the message will be deleted. The message is not deleted from the mobile
phone.
The simple alarm window can be displayed, while using some applications such as
Media Play, Contents Library, etc. In this case, to view the contents of the message,
switch to TV viewing mode.
When the message of an unknown mobile phone is displayed, select the mobile
phone in the Message item of the Home Network Centre and select Denied to block
the phone.
New message received
Doyou want to view
the details?
Cancel
OK
Media Play
USB : USB
851.98MB/995.00MB Free
PHOTO
❑ Message View
If a new text message (SMS) arrives while you are watching TV, the alarm window
appears. If you click the OK button, the contents of the message are displayed.
• If you select the OK button, the contents of the message are displayed.
• If you select the Cancel button, the alarm window appears up to three times at
5 minute intervals.
N You can configure the viewing settings for the text message (SMS) contents on
the mobile phone. For the procedures, refer to the mobile phone manual.
N Some special characters may be displayed as blank or broken characters.
Photo
USB
Music
husband
Setup
Movie
 Device
e Return
husband
Call
You have a phone call
Mom
❑ Call Arrival Alarm
If a call arrives while you are watching TV, the alarm window appears.
• If you select the OK button, the call arrival alarm is confirmed and the alarm
window is closed.
• If you select the Cancel button, the alarm window appears up to three times at 5
minute intervals.
❑ Schedule Alarm
While you are watching TV, the alarm window appears to display the registered
schedule.
• If you select the OK button, you can view the contents of the schedule registered
on the mobile phone.
• If you select the Cancel button, the alarm window appears up to three times at 5
minute intervals.
N You can configure the viewing settings for the schedule contents on the mobile
phone.
For the procedures, refer to the mobile phone manual.
N Some special characters may be displayed as blank or broken characters.
011-298-2030
Cancel
OK
husband
Scheduled event
You have a schedule
Do you want to view
the details?
OK
Cancel
English - 56
BN68-01939A-Eng.indd 56
2009-04-15 오후 2:55:13
Using the Media Function
An alarm window appears informing the user that the media contents (videos, photos, music) sent from the mobile phone will be
displayed on the TV.
The contents are played automatically 3 seconds after the alarm window appears.
If you press the RETURN or EXIT button when the alarm window appears,
the Media Contents are not played.
N To turn off the media contents transmission from the mobile phone, set Media to Off in Setup of the Home Network Centre.
N The contents may not be played on the TV depending on their resolution and format.
❑ Media play control buttons
Button
Operations
◄/►
(ENTER
RETURN
TOOLS
)
•
•
•
•
Move the cursor and select an item.
While playing a movie file: skip forwards or backwards through the movie file.
Pressing the ENTERE button during play pauses the play.
Pressing the ENTERE button during pause resumes the play.
Return to the previous menu.
Run various functions from the Photo, Music and Movie menus.
INFO
Show file information.
EXIT
Stop Media Play mode and Returns to TV mode.
N The ENTERE and ◄/► buttons may not work depending on the type of media content.
N Using the mobile device, you can control playing media. For details, refer to each user’s guide.
English - 57
BN68-01939A-Eng.indd 57
2009-04-15 오후 2:55:13
About Anynet+
Connecting Anynet+ Devices
The Anynet+ system can be used only with Samsung devices that have the Anynet+ feature. To be sure your Samsung device has this
feature, check if there is an Anynet+ logo on it.
❑ To connect to a TV
Anynet+
Device 1
TV
HDMI 1.3 Cable
Anynet+
Device 2
HDMI 1.3 Cable
Anynet+
Device 3
HDMI 1.3 Cable
Anynet+
Device 4
HDMI 1.3 Cable
1. Connect the [HDMI IN 1], [HDMI IN 2(DVI)], [HDMI IN 3], or [HDMI IN 4] jack on the TV and the HDMI OUT jack of the
corresponding Anynet+ device using an HDMI cable.
❑ To connect to Home Theater
TV
Home Theatre
HDMI 1.3 Cable
Anynet+ Device 2
HDMI 1.3 Cable
HDMI 1.3 Cable
Anynet+ Device 3
HDMI 1.3 Cable
Anynet+ Device 1
Anynet+ Device 4
HDMI 1.3 Cable
1. Connect the[HDMI IN 1], [HDMI IN 2(DVI)], [HDMI IN 3], or [HDMI IN 4] jack on the TV and the HDMI OUT jack of the corresponding
Anynet+ device using an HDMI cable.
2. Connect the HDMI IN jack of the home theater and the HDMI OUT jack of the corresponding Anynet+ device using an HDMI cable.
N
N
N
N
Connect only one Home Theater.
You can connect an Anynet+ device using the HDMI 1.3 cable. Some HDMI cables may not support Anynet+ functions.
Anynet+ works when the AV device supporting Anynet+ is in the Standby or On status.
Anynet+ supports up to 12 AV devices in total. Note that you can connect up to 3 devices of the same type.
English - 58
BN68-01939A-Eng.indd 58
2009-04-15 오후 2:55:14
Setting Up Anynet+
Anynet+ is a function that enables you to control all connected Samsung
devices that support Anynet+ with your Samsung TV’s remote.
You can also display Anynet+ menu by selecting Tools → Anynet+(HDMI-CEC).
Application
T Press the TOOLS button to display Tools menu.
Media Play (USB & DLNA)
Anynet+ (HDMI-CEC)
►
Content Library
Internet@TV
Home Network Centre
❑ Setup
You can set the environment for using Anynet+.


Anynet+(HDMI-CEC) → Off / On
To use the Anynet+ Function, Anynet+ (HDMI-CEC) must be set to On.
N When the Anynet+ (HDMI-CEC) function is disabled, all the Anynet+ related
operations are deactivated.
Auto Turn Off → No / Yes
Setting an Anynet+ Device to turn Off Automatically when the TV is Turned Off
N The active source on the TV remote must be set to TV to use the Anynet+ function.
N If you set Auto Turn Off to Yes, connected external devices are also turned off
when the TV is turned off. If an external device is still recording, it may or may not
turn off.
Anynet+(HDMI-CEC)
: On
Auto Turn Off
: Yes
U Move
▶
E Enter
R Return
Scanning and Switching between Anynet+ Devices
1. Press the TOOLS button. Press the ENTERE button to select
Anynet+ (HDMI-CEC).
2. Press the ▲ or ▼ button to select Device List, then press the ENTERE button.
N Anynet+ devices connected to the TV are listed.
N If you cannot find a device you want, press the red button to scan for devices.
3. Press the ▲ or ▼ button to select to a particular device and press the ENTERE
button. It is switched to the selected device.
N Only when you set Anynet+ (HDMI-CEC) to On in the Application menu, the
Device List menu appears.
View TV
Device List
Recording
:
DVDR
DVDR Operation
Receiver On
Setup
U Move
E Enter
R Return
Switching to the selected devices may take up to 2 minutes. You cannot cancel the operation during the switching operation.
The time required to scan for devices is determined by the number of connected devices.
When the device scan is complete, the number of devices found are not displayed.
Although the TV automatically searches the device list when the TV is turned on via the power button, devices connected to the TV
when the TV is on or under some conditions are not automatically displayed in the device list. Press the red button to search for the
connected device.
N If you have selected external input mode by pressing the SOURCE button, you cannot use the Anynet+ function. Make sure to
switch to an Anynet+ device by using the TOOLS button.
N
N
N
N
Continued...
English - 59
BN68-01939A-Eng.indd 59
2009-04-15 오후 2:55:14
❑ Anynet+ Menu
The Anynet+ menu changes depending on the type and status of the Anynet+ devices connected to the TV.
Anynet+ Menu
View TV
Device List
(device_name) Menu
(device_name) Operation
Recording: (*recorder)
(*recorder) Reserve Recording
Stop Recording: (*recorder)
Receiver
Description
Anynet+ mode changes to TV broadcast mode.
Shows the Anynet+ device list.
Shows the connected device menus. E.g. If a DVD recorder is connected, the disc menu of the
DVD recorder will appear.
Shows the play menu of the connected device. E.g. If a DVD recorder is connected, the play menu
of the DVD recorder will appear.
Starts recording immediately using the recorder. (This is only available for devices that support the
recording function.)
Enables reserving a recording for the recorder. (This is only available for devices that support the
recording reservation function.)
Stops recording.
Sound is played through the receiver.
❑ TV Remote Control Buttons Available in Anynet+ Mode
Device Type
Operating Status
Available Buttons
Anynet+ Device
After switching to the device, when
the menu of the corresponding
device is displayed on the screen.
Numeric buttons
▲/▼/◄/►/ENTERE buttons
Colour buttons / EXIT button
After switching to the device, while
playing a file
(Backward search) /
(Pause)
Device with builtin Tuner
After switching to the device, when
you are watching a TV programme
P
Audio Device
When Receiver is activated
=
/
button
M MUTE button
N
N
N
N
N
N
N
/
(Forward search) /
(Stop) /
(Play) /
button
The Anynet+ function only works when the active source on the TV remote control is set to TV.
The
button works only while in the recordable state.
You cannot control Anynet+ devices using the buttons on the TV. You can control Anynet+ devices only using the TV remote control.
The TV remote control may not work under certain conditions. In this case, reselect the Anynet+ device.
The Anynet+ functions do not operate with other manufacturers’ products.
In Anynet+ mode, the colour buttons may not work properly.
The
,
operations may differ depending on the device.
Recording
You can make a recording of a TV programme using a Samsung recorder.
1. Press the TOOLS button. Press the ENTERE button to select Anynet+ (HDMI-CEC).
2. Press the ▲ or ▼ button to select Recording: (device_name), then press the
ENTERE button. Recording begins.
N When there is more than one recording device
View TV
Device List
Recording
:
DVDR
DVDR Operation
Receiver On
When multiple recording devices are connected, the recording devices are listed.
Setup
Press the ▲ or ▼ button to select a recording device and press the ENTERE
button. Recording begins.
U Move
E Enter
R Return
N When the recording device is not displayed
Select Device List and press the red button to search devices.
N You can record the source streams by selecting Recording: (device_name).
N Pressing the
button will record whatever you are currently watching. If you are watching video from another device, the video
from the device is recorded.
N Before recording, check whether the antenna jack is properly connected to the recording device. To properly connect an antenna to
a recording device, refer to the recording device’s users manual.
English - 60
BN68-01939A-Eng.indd 60
2009-04-15 오후 2:55:14
Listening through a Receiver (Home theater)
You can listen to sound through a receiver instead of the TV speaker.
1. Press the TOOLS button. Press the ENTERE button to select Anynet+ (HDMI-CEC).
2. Press the ▲ or ▼ button to select Receiver. Press the ◄ or ► button to select On or Off.
N If your receiver supports audio only, it may not appear in the device list.
N When listening through the receiver, there are restrictions for using the PIP and audio-
related (MTS, Preferred language) menus.
N When using the Media Play feature, sound may not output properly through the receiver.
N If there is a power interruption to the TV when the Receiver is set to On (by
disconnecting the power cord or a power failure), the Speaker Select may be set to
External Speaker when you turn the TV on again.
View TV
Device List
Recording
:
DVDR
DVDR Operation
Receiver ◄
On
►
Setup
U Move
E Enter
R Return
Troubleshooting for Anynet+
Symptom
Anynet+ does not work.
Solution
•
•
•
•
•
•
•
•
•
I want to start Anynet+.
•
•
•
I want to exit Anynet+.
•
•
•
The message Connecting to
Anynet+ device...
appears on the screen.
The Anynet+ device does not
play.
The connected device is not
displayed.
The TV programme cannot be
recorded.
•
•
•
Check if the device is an Anynet+ device. The Anynet+ system supports Anynet+ devices only.
Connect only one receiver (home theater).
Check if the Anynet+ device power cord is properly connected.
Check the Anynet+ device’s Video/Audio/HDMI 1.3 cable connections.
Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.
Check whether the TV remote control is in TV mode.
Check whether it is Anynet+ exclusive remote control.
Anynet+ doesn’t work in certain situations. (Searching channels, Operating Media Play, Plug
& Play, etc.)
When connecting or removing the HDMI 1.3 cable, please make sure to search devices again
or turn your TV off and on again.
Check if the Anynet+ Function of Anynet+ device is set on.
Check if the Anynet+ device is properly connected to the TV and check if the Anynet+
(HDMI-CEC) is set to On in the Anynet+ Setup menu.
Press the TV button on the TV remote control to switch to TV.
Then press the TOOLS button to show the Anynet+ menu and select a menu you want.
Select View TV in the Anynet+ menu.
Press the SOURCE button on the TV remote control and select a device other than Anynet+
devices.
(Note that the channel button operates only when a tuner-embedded Anynet+ device is not
connected.)
You cannot use the remote control when you are configuring Anynet+ or switching to a view
mode.
Use the remote control when the Anynet+ setting or switching to view mode is complete.
You cannot use the play function when Plug & Play is in progress.
Check whether or not the device supports Anynet+ functions.
Check whether or not the HDMI 1.3 cable is properly connected.
Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.
Search Anynet+ devices again.
You can connect an Anynet+ device using the HDMI 1.3 cable only. Some HDMI cables may
not support Anynet+ functions.
• If it is terminated by an abnormal situation such as disconnecting the HDMI cable or power
cord or a power failure, please repeat the device scan.
• Check whether the antenna jack on the recording device is properly connected.
•
•
•
•
•
English - 61
BN68-01939A-Eng.indd 61
2009-04-15 오후 2:55:15
Recommendations for Use
Teletext Feature
Most television stations provide written information services via Teletext. The index page of the teletext service gives you information on
how to use the service. In addition, you can select various options to suit your requirements by using the remote control buttons.
N For teletext information to be displayed correctly, channel reception must be stable. Otherwise, information may be missing or some
pages may not be displayed.
1 : (exit)
Exit from the teletext display.
2 6 (index)
Used to display the index (contents) page at any time while you are viewing teletext.
3 8 (store)
Used to store the teletext pages.
1
4 4 (size)
Press to display the double-size letters in the upper half of the screen.
For lower half of the screen, press it again. To display normal screen, press it once
again.
5 / (teletext on/mix)
Press to activate teletext mode after selecting the channel providing the teletext
service. Press it twice to overlap the teletext with the current broadcasting screen.
6 5 (reveal)
Used to display the hidden text (answers to quiz games, for example).
To display normal screen, press it again.
7 1 (sub-page)
Used to display the available sub-page.
7
8
2
3
4
9
0
!
8 2 (page up)
Used to display the next teletext page.
9 3 (page down)
Used to display the previous teletext page.
0 0 (mode)
Press to select the teletext mode (LIST/FLOF). If you press it in the LIST mode, it
switches into the List save mode. In the List save mode, you can save teletext page
into list using the 8(store) button.
! 9 (hold)
Used to hold the display on a given page if the selected page is linked with several
secondary pages which follow on automatically. To resume, press it again.
@
#
5
6
@ 7 (cancel)
Used to display the broadcast when searching for a page.
# Colour buttons (red/green/yellow/blue)
If the FASTEXT system is used by a broadcasting company, the different topics
covered on a teletext page are colour-coded and can be selected by pressing the
coloured buttons. Press one of them corresponding to the required. The page is
displayed with other coloured information that can be selected in the same way.
To display the previous or next page, press the corresponding coloured button.
N You can change teletext pages by pressing the numeric buttons on the remote control.
Continued...
English - 62
BN68-01939A-Eng.indd 62
2009-04-15 오후 2:55:15
The teletext pages are organized according to six categories:
Part
Contents
A
Selected page number.
B
Broadcasting channel identity.
C
Current page number or search indications.
D
Date and time.
E
Text.
F
Status information.
FASTEXT information.
N Teletext information is often divided between several pages displayed in sequence,
which can be accessed by:
- Entering the page number
- Selecting a title in a list
- Selecting a coloured heading (FASTEXT system)
O Press the TV button to exit from the teletext display.
Wall Mount Kit Specifications (VESA)
Install your wall mount on a solid wall perpendicular to the floor.
When attaching to other building materials, please contact your nearest dealer.
If installed on a ceiling or slanted wall, it may fall and result in severe personal injury.
Product Family
LCD-TV
PDP-TV
N
N
N
N
N
N
N
N
inch
VESA Spec. (A * B)
19" ~22"
100 * 100
23"~29"
200 * 100
30"~40"
200 * 200
46"~55"
400 * 400
57"~70"
800 * 400
80" ~
1400 * 800
42"~ 50"
400 * 400
58"~ 63"
600 * 400
70" ~
800 * 400
80" ~
1400 * 800
Standard
Screw
Quantity
M4
M6
4
M8
M8
4
We provided the standard dimensions for wall mount kits as shown in the table above.
When purchasing our wall mount kit, a detailed installation manual and all parts necessary for assembly are provided.
Do not use screws longer than the standard dimension, as they may cause damage to the inside of the TV set.
For wall mounts that do not comply with the VESA standard screw specifications, the length of the screws may differ depending on
their specifications.
Do not use screws that do not comply with the VESA standard screw specifications.
Do not use fasten the screws too strongly, this may damage the product or cause the product to fall, leading to personal injury.
Samsung is not liable for these kinds of accidents.
Samsung is not liable for product damage or personal injury when a non-VESA or non-specified wall mount is used or the consumer
fails to follow the product installation instructions.
Our 57” and 63” models do not comply with VESA Specifications. Therefore, you should use our dedicated wall mount kit for this
model.
Do not exceed 15 degrees tilt when mounting this TV.
Do not install your Wall Mount Kit while your TV is turned on.
It may result in personal injury due to electric shock.
English - 63
BN68-01939A-Eng.indd 63
2009-04-15 오후 2:55:15
Preparing before installing Wall- Mount on the wall
Case A. Installing SAMSUNG Wall-Mount
Case B. Installing other company’s Wall-Mount

1. Install Wall Mount with the torque range of 15kgf·cm or less. Make sure that parts can be damaged if the torque is out of the
specified range.
2.Accessory Kit contains Holder–Ring [①] for installing other company’s Wall-Mount on Samsung TV. (Case B)
How to attach the Stand-Base
Using the screws for securing the stand base and the TV, firmly attach the TV to the
stand base.
(The exterior of the set may be different from the picture.)
(PS50B650)
When mounting your TV on a wall, install
the cover (➊) on the stand-base using two
screws.
(PS58B680/PS63B680)
Warning
Firmly secure the stand to the TV before moving it, as the stand may fall and could
cause serious injury.
N Two or more people should carry the TV. Never lay the TV on the floor because of
possible damage to the screen. Always store the TV upright.
English - 64
BN68-01939A-Eng.indd 64
2009-04-15 오후 2:55:17
경고
주의
Securing the TV to the Wall
Pulling, pushing, or climbing on the TV may cause the TV to fall. In particular, ensure your children do not hang
over or destabilize the TV; doing so may cause the TV to tip over, causing serious injuries or death. Follow all
safety precautions provided on the included Safety Flyer. For added stability, install the anti-fall device for safety
purposes, as follows.
경고
주의
Wall
Wall
To avoid the TV from falling
1. Put the screws into the clamps and firmly fasten them onto the wall. Confirm that the screws have been firmly installed onto the wall.
N You may need additional material such as an anchor depending on the type of wall.
N Since the necessary clamps, screws, and string are not supplied, please purchase these additionally.
2. Remove the screws from the center back of the TV, put the screws into the clamps, and then fasten the screws onto the TV again.
N Screws may not be supplied with the product.
3. Connect the clamps fixed onto the TV and the clamps fixed onto the wall with a strong string and then tie the string tightly.
N Install the TV near to the wall so that it does not fall backwards.
N It is safe to connect the string so that the clamps fixed on the wall are equal to or lower than the clamps fixed on the TV.
N Untie the string before moving the TV.
4. Verify all connections are properly secured. Periodically check connections for any sign of fatigue for failure.
If you have any doubt about the security of your connections,contact a professional installer.
Securing the Installation Space
Keep the required distances between the product and other objects (e.g. walls) to ensure proper ventilation.
Failing to do so may result in fire or a problem with the product due to an increase in the internal temperature of the product.
Install the product so the required distances shown in the figure are kept.
N When using a stand or wall-mount, use parts provided by Samsung Electronics only.
- If you use parts provided by another manufacturer, it may result in a problem with the product or an injury due to the product
falling.
- If you use parts provided by another manufacturer, it may result in a problem with the product or fire due to an increase in ����
the
internal temperature of the product due to poor ventilation.
N The appearance may differ depending on the product.

When installing the product with a stand
10 cm
10 cm
10 cm

When installing the product with a wall-mount
10 cm
10 cm
10 cm
10 cm
10 cm
10 cm
10 cm
10 cm
10 cm
10 cm
10 cm
English - 65
BN68-01939A-Eng.indd 65
2009-04-15 오후 2:55:18
Troubleshooting
Before contacting the Samsung after-sales service, perform the following simple checks.
If you cannot solve the problem using the instructions below, note the model and serial number of the television and contact your local
dealer.
No sound or picture
•
•
•
•
•
Normal picture but no sound
• Check the volume.
• Check whether the M MUTE button has been pressed on the remote control.
No picture or black and white
picture
• Adjust the colour settings.
• Check that the broadcast system selected is correct.
Sound and picture
interference
• Try to identify the electrical appliance that is affecting the television, then move it further away.
• Plug the television into a different main socket.
Blurred or snowy picture,
distorted sound
• Check the direction, location and connections of your aerial.
• This interference often occurs due to the use of an indoor aerial.
Remote control malfunctions
•
•
•
•
Replace the remote control batteries.
Clean the upper edge of the remote control (transmission window).
Check that the + and – ends of the batteries are inserted correctly.
Check that the batteries are drained.
Screen is black and power
indicator light blinks steadily
•
•
•
•
•
•
On your computer check; Power, Signal Cable.
Move the computer’s mouse or press any key on the keyboard.
On your equipment check (STB, DVD, etc) ; Power, Signal Cable.
The TV is using its power management system.
Press the Source button on the panel or remote control.
Turn the TV off and on.
The damaged picture appears
in the corner of the screen.
• If Screen Fit is selected in some external devices, the damaged picture may appear in the
corner of the screen. This symptom is caused by external devices, not TV.
The "Resets all settings to
the default values" message
appears.
• This appears when you press and hold the EXIT button for a while.
The product settings are reset to the factory defaults.
Check that the mains lead has been connected to a wall socket.
Check that you have pressed the button on your set.
Check the picture contrast and brightness settings.
Check the volume.
Check if Speaker Select is set to External Speaker.
English - 66
BN68-01939A-Eng.indd 66
2009-04-15 오후 2:55:19
Specifications
The descriptions and characteristics in this booklet are given for information purposes only and are subject to modification without
notice.
Model Name
PS50B650
PS58B680
50 inch
58 inch
63 inch
1920 x 1080 @ 60 Hz
1920 x 1080 @ 60 Hz
1920 x 1080 @ 60 Hz
10 W x 2
15 W x 2
15 W x 2
Body
1231 x 756 x 74 mm
1401.3 x 847.9 x 74 mm
1531 x 932 x 74 mm
With stand
1231 x 817 x 290 mm
1401.3 x 916.5 x 335 mm
1531 x 992.5 x 390 mm
Body
33.2 kg
38.9 kg
52.9 kg
With stand
38.2 kg
45.8 kg
60.6 kg
50 °F to 104 °F (10 °C to 40 °C)
50 °F to 104 °F (10 °C to 40 °C)
50 °F to 104 °F (10 °C to 40 °C)
Screen Size (Diagonal)
PC Resolution (Optimum)
Sound (Output)
PS63B680
Dimension (WxHxD)
Weight
Environmental Considerations
Operating Temperature
Operating Humidity
Storage Temperature
Storage Humidity
10% to 80%, non-condensing
10% to 80%, non-condensing
10% to 80%, non-condensing
-4 °F to 113 °F (-20 °C to 45 °C)
-4 °F to 113 °F (-20 °C to 45 °C)
-4 °F to 113 °F (-20 °C to 45 °C)
5% to 95%, non-condensing
5% to 95%, non-condensing
5% to 95%, non-condensing
N This device is a Class B digital apparatus.
N Design and specifications are subject to change without prior notice.
N For the power supply and Power Consumption, refer to the label attached to the product.
English - 67
BN68-01939A-Eng.indd 67
2009-04-15 오후 2:55:19
Contact SAMSUNG WORLDWIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer
care centre.
Country
Customer Care Centre 
Web Site
AUSTRALIA
1300 362 603
www.samsung.com/au
CHINA
800-810-5858
400-810-5858
010-6475 1880
www.samsung.com/cn
HONG KONG : 3698-4698
www.samsung.com/hk
INDIA
3030 8282
1800 110011
1800 3000 8282
www.samsung.com/in
INDONESIA
0800-112-8888
www.samsung.com/id
JAPAN
0120-327-527
www.samsung.com/jp
MALAYSIA
1800-88-9999
www.samsung.com/my
NEW ZEALAND
0800 SAMSUNG (0800 726 786)
www.samsung.com/nz
PHILIPPINES
1-800-10-SAMSUNG(726-7864)
1-800-3-SAMSUNG(726-7864)
02-5805777
www.samsung.com/ph
SINGAPORE
1800-SAMSUNG(726-7864)
www.samsung.com/sg
SOUTH AFRICA
0860-SAMSUNG(726-7864 )
www.samsung.com/za
TAIWAN
0800-329-999
www.samsung.com/tw
THAILAND
1800-29-3232
02-689-3232
www.samsung.com/th
TURKEY
444 77 11
www.samsung.com/tr
U.A.E
800-SAMSUNG (726-7864)
8000-4726
www.samsung.com/ae
VIETNAM
1 800 588 889
www.samsung.com/vn
BN68-01939A-00
BN68-01939A-Eng.indd 68
2009-04-15 오후 2:55:19
Download PDF