Samsung | PS-63P3H | Samsung PS-63P3H User Manual

PDP-TELEVISION
(PLASMA DISPLAY PANEL)
PS42P3S
PS50P3H
PS63P3H
PS50P3H
PS63P3H
Owner’s Instructions
Before operating the unit,
please read this manual thoroughly,
and retain it for future reference.
ON-SCREEN MENUS
PICTURE IN PICTURE (PIP)
TELETEXT / TELEWEB (OPTION)
Safety Instructions
ENG
◆ Do not place the PDP on an unstable cart, stand, tripod, bracket, table, or floor where it can fall.
◆ Do not expose the PDP to extreme temperature conditions or to extreme humidity conditions.
◆ Do not expose the PDP to direct sunlight and other sources of heat.
◆ Do not expose the PDP to any liquids.
◆ Never put objects of any kind into the television, and do not place a water-containing vessel on the
PDP.
◆ During a storm conditions (especially when there is lightning) unplug the PDP from the mains
socket and aerial.
◆ Do not step on or twist the power cord.
◆ Do not overload wall outlets or extension cords as this can result in a risk of fire or electric shock.
◆ Please use a soft and dry cloth (not containing volatile matter) when you clean the PDP.
◆ If the PDP is broken, do not try to repair it yourself. Contact qualified service personnel.
◆ If the remote control is not used for a long period of time, remove the batteries and store it in a
cool, dry place.
◆ Do not drop the remote control.
◆ When installing a PDP such as for an exhibition, etc., there is risk of overheating the unit if placed
directly on a floor or carpet. Be sure to use a proper stand, wall mount, ceiling mount, or Lift-Stand
offered by Samsung. (Do not use and exhibit by laying down or sitting the unit directly on the floor.)
User Instructions
◆ Screen Image retention
Do not display a still image (such as on a video game or when hooking up a PC to this PDP) on the
plasma monitor panel for more than 2 hours as it can cause screen image retention. This image
retention is also known as “screen burn”. To avoid such image retention, reduce the degree of
brightness and contrast of this screen when displaying a still image.
◆ Cell Defect
The plasma display panel consists of fine cells. Although the panels are produced with more than
99.9 percent active cells, there may be some cells that do not produce light or remain lit.
◆ Height
The PDP can normally operate only under 2000m in height. It might abnormally function at a place
over 2000m in height and do not install and operate there.
◆ Warranty
- Warranty Period: Two years starting from the purchase of your PDP.
- Warranty does not cover any damage caused by image retention.
- Burn-in is not covered by the warranty.
2
Caution
ENG
The lightning flash and arrow
head within the triangle is a
warning sign alerting you of
“dangerous voltage” inside
the product.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The exclamation point within
the triangle is a warning sign
alerting you of important
instructions accompanying
the product.
CAUTION: TO PREVENT ELECTRICAL SHOCK, DO NOT
REMOVE REAR COVER, NO USER SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
WARNING: TO PREVENT DAMAGE WHICH MAY RESULT IN
FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE.
main voltage is indicated on the
☛ The
rear of the PDP and the frequency is
50 or 60Hz.
Checking Parts
A Separated Sales
Ferrite Cores for
Speaker Wire
Owner’s Instructions
Component Cables
Remote Control/
AAA Batteries
Power Cord
Speaker Wires
Antenna Cable
PC Cable
DNIeTM (Digital Natural Image engine)
This feature bring you more detailed image with 3D noise reduction, detail enhancement, contrast
enhancement and white enhancement. New image compensation Algorithm gives brighter, clearer,
much detailed image to you. DNIeTM technology will fit every signals into your eyes.
3
ENG
Contents
◆ FOREWORD
■
■
■
Safety Instructions .........................................................................................
User Instructions............................................................................................
Caution ..........................................................................................................
2
2
3
◆ CONNECTING AND PREPARING YOUR DISPLAY
■
■
■
■
■
■
■
■
■
■
■
■
■
Your New Plasma Display Panel...................................................................
Infrared Remote Control ................................................................................
IInserting the Batteries in the Remote Control...............................................
Installing the Display on the Wall Attachment Panel .....................................
Connecting Speakers ....................................................................................
Connecting to an Aerial or Cable Television Network ...................................
Connecting a Satellite Receiver or Decoder..................................................
Switching On and Off.....................................................................................
Placing in Standby Mode...............................................................................
Becoming Familiar with the Remote Control .................................................
Setting Up Your Remote Control ...................................................................
Plug & Play Feature.......................................................................................
Choosing Your Language..............................................................................
6
8
9
10
12
14
14
15
15
16
17
18
19
◆ SETTING THE CHANNELS
■
■
■
■
■
■
Storing Channels Automatically.....................................................................
Sorting the Stored Channels .........................................................................
Storing Channels Manually............................................................................
Assigning Names to Channels ......................................................................
Activating the Child Lock and Skipping Unwanted Channels ........................
Selecting a Channel by Information...............................................................
20
21
22
24
25
26
◆ USING YOUR DISPLAY (continued)
■
■
■
■
■
■
■
■
■
■
4
Changing the Picture Standard .....................................................................
Adjusting the Picture Settings........................................................................
Adjusting the Picture Settings (PC or DVI Mode) ..........................................
Setting the Picture (PC Mode).......................................................................
Setting the Picture (Component Mode) .........................................................
Extra Picture Settings ....................................................................................
- Digital NR
- Size
- LNA (Low Noise Amplifier)
Setting the Blue Screen.................................................................................
Selecting the Film Mode (Video or S-Video Mode) .......................................
DNIeTM (Digital Natural Image engine)
...............................................
Freezing the Current Picture .........................................................................
26
27
28
29
30
31
32
32
33
33
ENG
Contents (continued)
◆ USING YOUR DISPLAY
■
■
■
■
■
■
■
■
Changing the Sound Standard ......................................................................
Adjusting the Sound Settings ........................................................................
Extra Sound Settings.....................................................................................
- Auto Volume
- Melody
- Pseudo Stereo / Virtual Surround
Selecting the DUAL Mode (depending on the model) ...................................
Setting the Time and Switching the TV On/Off Automatically .......................
Setting the Sleep Timer .................................................................................
Viewing the Picture In Picture (PIP) ..............................................................
Listening to the Sound of the Sub Picture (PC or DVI Mode)........................
34
34
35
36
37
38
39
41
◆ USING THE TELETEXT FEATURE
■
■
■
■
■
Teletext Feature ............................................................................................
Displaying the Teletext Information ...............................................................
Selecting Display Options..............................................................................
Selecting the Teletext Source (Option)..........................................................
Selecting a Teletext Page..............................................................................
42
43
43
44
45
◆ USING THE TELEWEB FEATURE
■
■
■
TeleWeb Feature (Option).............................................................................
Using the TeleWeb Menu after Displaying the TeleWeb...............................
Easy Accessing the TeleWeb Service via the Remote Control .....................
46
47
48
◆ ADDITIONAL INFORMATION AND CONNECTIONS
■
■
■
■
■
■
■
■
■
Viewing Pictures From External Sources ......................................................
Connecting to the External Devices ..............................................................
Connecting to the DVD Input.........................................................................
Connecting to the S-Video Input....................................................................
Connecting to the DVI Input ..........................................................................
Connecting to the PC Input ...........................................................................
Setting up Your PC Software (Windows only) ...............................................
Input Mode (PC/DVI) .....................................................................................
Pin Configurations .........................................................................................
48
49
50
50
51
51
52
53
54
◆ RECOMMENDATIONS FOR USE
■
Troubleshooting: Before Contacting Service Personnel................................
Symbols
Press
☛
➢
Important
Note
5
55
Your New Plasma Display Panel
➢
ENG
The actual configuration on your PDP may be different,
depending on your model.
Front Panel
PS42P3S/PS50P3H
a
b
c
Speaker
Speaker
PS63P3H
a
a
b
c
b
Power Indicator
SOURCE
- Power Off; Red
- Power On; Off
- Timer On; Green
External input selection.
MENU
Menu display.
- VOL +
Volume adjustment.
▼ CH ▲
Channel selection.
I/
Press to turn the PDP on and off.
6
c
Remote Control Signal Receiver
Aim the remote control towards this spot on the
PDP.
Your New Plasma Display Panel (continued)
➢
The actual configuration on your PDP may be different,
depending on your model.
ENG
Rear Panel
➢
a
For further details about connection, refer to pages 48~50.
b
c
d
e
f
a) ONLY FOR SERVICE
Connector for service only.
g
h
j
i
k
g) COMPONENT IN
Inputs for external devices, such as DVD, video
game device or video disc players.
b) DVI IN
Connect to the video output jack for device with
DVI output.
c) AUDIO
Connect to the audio output jack on your PC or any
device with DVI output.
h) EXT SPEAKER (8Ω)
Connect external speakers.
i) ANT IN VHF/UHF
75Ω Coaxial connector for Aerial/Cable Network.
j) WOOFER OUT
d) PC IN (RGB IN)
Connect to the sub-woofer speaker jack.
Connect to the video output jack on your PC.
k) POWER IN
e) MONITOR OUT (VIDEO / L-AUDIO-R)
Connect the supplied power cord.
Outputs for external devices
f) S-VIDEO IN / L-AUDIO-R / VIDEO IN
Video and audio inputs for external devices with an
S-Video output, such as a camcorder or VCR.
7
Infrared Remote Control
ENG
TURNS THE PDP ON AND OFF
PRESS TO SELECT A PRESE TIME
INTERVAL FOR AUTOMATIC
SHUTOFF
PICTURE SIZE
WHEN YOU PRESS A BUTTON , ‘
’
APPEARS ALONG WITH SELECED MODE
(TV, VCR, CATV, DVD OR STB) AND
REMAINING BATTERIES ON LED
MAKE THE REMOTE CONTROL WORKS
FOR TV, VCR, CATV, DVD PLAYER, STB
DIRECT CHANNEL SELECTION
TUNES TO THE PREVIOUS CHANNEL
SELECT CHANNEL BY
INFORMATION
VOLUME INCREASE
TEMPORARY SOUND SWITCH-OFF
NEXT CHANNEL/
TELETEXT NEXT PAGE/
TELEWEB FORWARD
EXTERNAL INPUT SELECTION/
TELETEXT SIZE SELECTION
VOLUME DECREASE
PICTURE EFFECT SELECTION/
TELETEXT CANCEL
PREVIOUS CHANNEL/
TELETEXT PREVIOUS PAGE/
TELEWEB BACKWARD
INFORMATION DISPLAY/
TELETEXT REVEAL
EXIT FROM ANY DISPLAY
MENU DISPLAY/
TELETEXT INDEX
MOVE TO THE REQUIRED
MENU OPTION/
ADJUST AN OPTION VALUE
RESPECTIVELY
PICTURE STILL
DNIe ON/OFF/DEMO
FASTEXT TOPIC SELECTION
TELETEXT ON VIDEO & TEXT MIX
TELETEXT OFF
(Refer to page 43 for details)
TELEWEB DISPLAY
(OPTION)
IF YOUR REMOTE CONTROL IS NOT
FUNCTIONING PROPERLY, TAKE
OUT THE BATTERIES AND PRESS
THE RESET BUTTON FOR ABOUT
2~3 SECONDS. RE-INSERT THE
BATTERIES AND TRY USING THE
REMOTE CONTROL AGAIN.
➢
8
CONFIRM YOUR CHOICE
(STORE OR ENTER)
CHANNEL SCAN
SOUND MODE SELECTION
TELEWEB HOME PAGE/
TELETEXT SUBPAGE
PIP FUNCTIONS;
- PIP ACTIVATING OR DEACTIVATING
(PIP ON)
- USED TO MOVE THE SUB PICTURE
COUNTERCLOCKWISE (LOCATE)
- USED TO ASSIGN A SOURCE OF SUB
PICTURE (SOURCE)
- SELECTING THE CHANNEL OF SUB
PICTURE (P^/∨)
VCR/DVD FUNCTIONS;
- REWIND (REW)
- STOP
- PLAY/PAUSE
- FAST FORWARD (FF)
The performance of the remote control may be affected by bright light.
Inserting the Batteries in the Remote Control
ENG
You must insert or replace the batteries in the remote control when
you:
◆ Purchase the PDP
◆ Find that the remote control is no longer operating
correctly
1
Remove the cover on the rear of the remote control by pressing
the symbol ( ) downwards and then pulling firmly to remove it.
2
Insert two R03, UM4, “AAA” 1.5V or equivalent batteries taking
care to respect the polarities:
◆ - on the battery against - on the remote control
◆ + on the battery against + on the remote control
3
Replace the cover by aligning it with the base of the remote
control and pressing it back into place.
9
Installing the Display on the Wall Attachment Panel
ENG
☛
This wall mount bracket installation guide is for the following models: WMN4230/WMN5030/WMN6330.
This installation guide may be different from the PDP User’s manual. Please refer to the proper
installation guide for your product.
Installation Notes
◆ Do not install the PDP on any place other than vertical walls.
◆ To protect the performance of the PDP and prevent troubles, avoid the followings:
- Do not install next to smoke and fire detectors.
- Do not install in an area subjected to vibration or high voltage.
- Do not install near or around any heating apparatus.
◆ Use only recommended parts and components.
Mounting Kits
Wall Mount Bracket
PS42P3S/50P3H
Plastic Hanger
PS63P3H
Screws
PS42P3S/50P3H: 4
PS63P3H: 6
How to Adjust Mounting Angle
(depending on your model)
The wall mount bracket is delivered
separately. Please tighten the captive
screw in the direction of the arrow after
assembling the bracket.
10
1
Secure the PDP to the wall mount bracket.
(Please refer to the following instructions.)
2
Set the angle by pulling the upper end of the
PDP attached to bracket in the direction of the
arrow.
3
The angle can be adjusted from 0° to 20° by
±2°.
Installing the Display on the Wall Attachment Panel
ENG
1
Remove the screws from the back of the PDP.
PS42P3S
2
◆ Please ask the installers to install the wall mount bracket.
◆ Please be sure to check if the plastic hanger is completely secured on both the left and right
side after hanging the PDP on the wall mount bracket.
◆ Please avoid catching your fingers while installing and adjusting the angle.
◆ Please tightly secure the wall mount bracket to the wall to avoid injury from a falling PDP.
Tighten the screws of the plastic hanger to the back side of the PDP.
PS42P3S
4
PS63P3H
Use the screws and assemble the plastic hanger.
☛
3
PS50P3H
PS50P3H
PS63P3H
Put the 4 pegs on the PDP in the grooves of the wall mount bracket and pull down on the PDP (!) to
secure it to the wall mount bracket (@). Tighten the screws as shown (#) so that the PDP cannot be
separated from wall mount bracket.
PDP panel
Wall
Wall attachment panel bracket
11
Connecting Speakers
ENG
1
Remove the screws on the rear of the PDP.
PS42P3S
PS50P3H
PS63P3H
2
Hang the two “T” shaped hangers
on the square holes on the rear of
the PDP.
3
Tighten the PDP and the speaker bracket using the screws removed from the PDP.
PS42P3S
➢
PS42P3S
PS50P3H
PS50P3H
PS63P3H
PS63P3H
When moving your PDP, do NOT hold the speaker connected to your PDP. It may damage the
bracket clamping the speaker and your PDP together and result in a drop of your PDP and a risk of
personal damage and injury.
12
Connecting Speakers (continued)
ENG
Connect the speaker audio cable to the external speaker output jack on the rear of the PDP matching
the “+” and “-” ends of the cable with the diagram on the PDP.
Sub-woofer speaker
PS42P3S/PS50P3H
➢
◆ The speakers MUST have to a power
handling capability of 10 watts minimum
(impedance 8Ω).
◆ When you connect the speaker wire to the
external speaker out connector, first bind
the speaker wire round the ferrite core to
secure it.
Sub-woofer speaker
PS63P3H
Ferrite Cores
The ferrite cores are used to attenuate undesired signals.
When connecting cables, attach one of these ferrite cores to
the cable near the connector.
13
Connecting to an Aerial or Cable Television Network
ENG
To view television channels correctly, a signal must be received by
the set from one of the following sources:
◆ An outdoor aerial
◆ A cable television network
◆ A satellite network
1
In the first three cases, connect the aerial or network input cable to
the 75Ω coaxial socket on the rear of the PDP.
2
If you are using an indoor aerial, you may need to turn it when
tuning your PDP until you obtain a picture that is both sharp and
clear.
For further details, refer to:
◆ “Storing Channels Automatically” on page 20
◆ “Storing Channels Manually” on page 22
Rear of the PDP
or
Cable Television
Network
➢
When installing or re-installing your PDP, be sure to use the
supplied coaxial antenna cable. If you connect using a different
coaxial cable, there is risk of noise or interference to the screen
image. (You must not use another general purpose cable.
Use the 3M/5M/7M cable supplied by Samsung.)
Connecting a Satellite Receiver or Decoder
Rear of the PDP
In order to watch television programmes broadcast via a satellite
network, you must connect a satellite receiver to the rear of the
PDP. Also, in order to descramble a coded transmission signal, you
must connect a decoder to the rear of the PDP.
Using a Coaxial cable
Connect a coaxial cable to the:
◆ Receiver (or Decoder) output socket.
◆ Television aerial input socket.
➢
If you wish to connect both a satellite receiver (or decoder)
and a VCR, you should connect the:
◆ Receiver (or Decoder) to the VCR
◆ VCR to the PDP
Otherwise, connect the receiver (or decoder) directly to the
PDP.
Satellite receiver/
Decoder
14
Switching On and Off
ENG
The mains lead is attached to the rear of your PDP.
1
Result:
➢
2
Front of the PDP
Plug the mains lead into an appropriate socket.
The Standby indicator on the front of the PDP lights up.
The main voltage is indicated on the rear of the PDP and
the frequency is 50 or 60Hz.
Press the “ I / ” button on the front of the PDP (or POWER (
button on the remote control) to switch the PDP on.
Result:
)
The programme that you were watching last is reselected automatically.
you have not yet stored any channels, No clear picture
➣ Ifappears.
Refer to “Storing Channels Automatically” on page
20 or “Storing Channels Manually” on page 22.
3
To switch your PDP off, press the “ I /
TV
” button again.
Placing in Standby Mode
Your PDP can be placed in Standby mode, in order to reduce the
Power consumption.
The Standby mode can be useful when you wish to interrupt
viewing temporarily (during a meal, for example).
1
Press the POWER (
Result:
2
TV
) button on the remote control.
The screen is turned off and the Standby indicator on
the front of the PDP lights.
To switch the PDP back on, simply press the POWER (
again or a numeric button.
➣ You can also switch on by pressing the P
or
) button
button.
15
Becoming Familiar with the Remote Control
ENG
The remote control is used mainly to:
◆ Change channels and adjust the volume
◆ Display the on-screen menu system
The following table presents the most frequently used buttons and
their functions.
Button
to
PRE-CH
Menu Function
Used to display the next
stored channel.
-
Used to display the
previous stored channel.
-
Used to display the corresponding channels.
For double digit channels, the second digit must be
pushed immediately after the first. Failure to do this will
result in a single digit channel being displayed.
➢
Press the PRE-CH button. The TV will switch to the last
channel viewed.
To quickly switch between two channels that are far apart,
tune to one channel, then use the number button to select
second channel. Then, use the PRE-CH button to quickly
alternate between them.
Used to increase the
volume.
-
Used to decrease the
volume.
-
MUTE
Used to switch the sound off temporarily.
To turn the sound back on, press this button again, or
press the
or
button.
MENU
Used to display the
on-screen menu system.
Used to return to the previous
menu or normal viewing.
-
Used to:
◆ Display a submenu
containing selections for
the current menu option
◆ Increase/decrease a
menu option value
-
Used to confirm your choice.
-
Used to exit from the menu
system and return to normal
viewing directly.
EXIT
16
Viewing Function
➣
Setting Up Your Remote Control
ENG
This TV’s remote control can operate VCR, CATV , DVD, or Set-top
box (STB), in addition to controlling the TV.
➣
The remote control is not compatible with the TV
manufactured by another company.
1
Turn off your VCR, Cable box (CATV), DVD or STB.
2
Press the SELECT button. Mode is changed whenever SELECT
button is pressed. (new mode is displayed on LED screen.)
3
Press the POWER ( ) button on the remote control. The
component you select should turn on. If it turns on, your remote
control is now set correctly.
4
Once your remote control is set up, press the SELECT button any
time you want to use the remote control to operate your VCR,
Cable box, DVD or STB.
➣
VCR
When your remote control is in the VCR, CATV, DVD or
STB mode, the volume buttons still control your television’s
volume
17
Plug & Play Feature
ENG
When the television is initially powered ON, several basic customer
settings proceed automatically and subsequently. The following
settings are available.
Plug & Play
1
Language
Sel.
Result:
) button
The message Plug & Play is displayed. It flickers for
a little while, and then the Language menu is
automatically displayed.
2
Select the appropriate language by pressing the † or … button.
3
Press the
Result:
Store
4
Antenna input check
Area
If the television is in Standby mode, press the POWER (
on the remote control.
button to confirm your choice.
The message Antenna input check is displayed.
Make sure that the antenna is connected to the TV, and then
press the
button.
Result:
The Country menu is displayed.
5
Select your country by pressing the † or … button.
6
Press the
Result:
Asia/W.Europe
button to confirm your choice.
The Auto Store menu is displayed.
CIS/E.Europe
7
China
Hongkong/UK
To start the search, press the
Result:
Australia
NZ/Indonesia
Sel.
Store
➢
button.
The search will end automatically. Channels are sorted
and stored in an order which reflects their position in
the frequency range, (with lowest first and highest last).
The programme originally selected is then displayed.
To stop the search before it has finished or return to normal
viewing, press the MENU (
) button.
Auto Store
Area
Asia/W.Europe
1%
P0 -----
57 MHz
Exit
Enjoy viewing your new TV.
18
8
When it has finished, the message Enjoy viewing your new TV
is displayed, and then the channel which has been stored will be
activated.
Plug & Play Feature (continued)
ENG
If you want to reset this feature...
1
Press the MENU button.
The main menu is displayed.
Result:
2
Press the † or … button to select Function.
The options available in the Function group are
Result:
displayed.
3
Press the √ button.
4
Press the † or … button to select Plug & Play. Press the √
button.
Result:
5
The message Plug & Play is displayed.
Function
For further details on how to set, refer to the opposite page.
Language
English
Time
√
Teletext Source
Main
Plug & Play
√
Blue Screen
Off
√ Enter
Move
Return
Choosing Your Language
When you start using your television for the first time, you must
select the language which will be used for displaying menus and
indications.
Function
Language
1
2
3
English
Press the MENU button.
The main menu is displayed.
Result:
Time
√
Teletext Source
Main
Plug & Play
√
Press the † or … button to select Function.
The options available in the Function group are
Result:
displayed.
Blue Screen
Off
Move
Press the √ button.
The Language option is selected.
Result:
4
Press the √ button again.
The languages available are listed.
Result:
5
Select the appropriate language by pressing the † or … button.
6
Press the
7
When you are satisfied with your choice, press the MENU (
button to return to normal viewing.
√ Enter
Language
button to confirm your choice.
)
Sel.
Store
19
Return
Storing Channels Automatically
ENG
Channel
Area
Asia/W.Europe
Auto Store
√
Manual Store
√
Sort
√
Name
√
Edit
√
√ Enter
Move
You can scan for the frequency ranges available to you, (availability
depends on your country). Automatically allocated programme
numbers may not correspond to actual or desired programme
numbers. However you can sort numbers manually and clear any
channels you do not wish to watch.
1
Press the MENU button.
The main menu is displayed.
Result:
2
Press the † or … button to select Channel.
The options available in the Channel group are
Result:
displayed.
3
Press the √ button.
The Area option is selected.
Result:
4
Press the √ button again.
The countries available are listed.
Result:
5
Select your area by pressing the † or … button.
6
Press the
7
Press the MENU button.
The options available in the Channel group are
Result:
displayed again.
8
Press the † or … button to select Auto Store.
Press the √ button.
The Auto Store menu is displayed.
Result:
9
Press the
Return
Area
Asia/W.Europe
CIS/E.Europe
China
Hongkong/UK
Australia
NZ/Indonesia
Sel.
Store
Channel
Area
Asia/W.Europe
Auto Store
√
Manual Store
√
Sort
√
Name
√
Edit
√
Move
√ Enter
Return
Auto Store
Area
Result:
Asia/W.Europe
0%
P0 -----
0 MHz
œ √ Sel.
Exit
Auto Store
Area
Asia/W.Europe
1%
P0 -----
57 MHz
Exit
20
➢
Start
10
button to confirm your choice
button to start the search.
The search will end automatically. Channels are sorted
and stored in an order which reflects their position in
the frequency range, (with lowest first and highest last).
The programme originally selected is then displayed.
To stop the search before it has finished, press the
MENU (
) button.
When the channels have been stored, you can:
◆ Sort them in the order required (see page 21)
◆ Clear a channel (see page 25)
◆ Fine-tune channel reception if necessary (see page 23)
◆ Assign a name to the stored channels (see page 24)
◆ Activate/deactivate the Digital Noise Reduction feature
(see page 31)
Sorting the Stored Channels
ENG
This operation allows you to change the programme numbers of
stored channels. This operation may be necessary after using store
channels. You can delete those channels you do not want to keep.
1
2
3
Press the MENU button.
The main menu is displayed.
Result:
Press the † or … button to select Channel.
The options available in the Channel group are
Result:
displayed.
Channel
Area
Asia/W.Europe
Auto Store
√
Manual Store
√
Sort
√
Name
√
Edit
√
Press the √ button.
4
Press the † or … button to select Sort. Press the √ button.
The Sort menu is displayed.
Result:
5
Select the channel that you wish to move by pressing the † or …
button. Press the √ button.
6
Select the number of the programme to which the channel is to be
moved by pressing the † or … button. Press the √ button.
The channel is moved to its new position and all other
Result:
channels are shifted accordingly.
√ Enter
Move
Return
Sort
96
97
98
99
0
1
2
3
4
5
6
7
8
*
*
*
*
*
C23
*
*
*
*
*
*
*
√ Sel.
Move
Exit
Sort
7
Repeat Steps 5 to 6 until you have moved all the channels to the
required programme numbers.
96
97
98
99
0
1
2
3
4
5
6
7
8
*
*
*
*
*
C23
*
*
*
*
*
*
*
œ Add
Sel.
21
Storing Channels Manually
ENG
You can store up to television channels, including those received
via cable networks.
Channel
Area
Asia/W.Europe
Auto Store
√
Manual Store
√
Sort
√
Name
√
Edit
√
◆ Whether or not to store each of the channels found
◆ The programme number of each stored channel which
you wish to identify
√ Enter
Move
When storing channels manually, you can choose:
Return
1
Press the MENU button.
The main menu is displayed.
Result:
2
Press the † or … button to select Channel.
The options available in the Channel group are
Result:
displayed.
3
Press the √ button.
4
Press the † or … button to select Manual Store.
Press the √ button.
The Manual Store menu is displayed.
Result:
5
If necessary, select the broadcasting standard required. Press the
† or … button to select Colour System and press the œ or √
button. The colour standards are displayed in the following order.
(depending on the model).
Manual Store
Prog. No
P 1
Colour System
AUTO
Sound System
BG
Search
891MHz
Channel
C 16
Fine Tune
œ √ Sel.
Move
Store
Manual Store
Prog. No
P 1
Colour System
AUTO
Sound System
BG
Search
891MHz
Channel
C 16
◆ AUTO - PAL - SECAM
6
Fine Tune
œ √ Sel.
Move
◆ AUTO - NTSC3.58 - NTSC4.43
Store
Press the † or … button to select Sound System and press the œ
or √ button. The sound standards are displayed in the following
order.
BG - DK - I - M
Manual Store
Prog. No
P 1
Colour System
AUTO
Sound System
BG
Search
891MHz
Channel
C 16
Fine Tune
Move
œ √ Sel.
22
Store
Storing Channels Manually (continued)
ENG
7
If you know the number of the channel to be stored, see the
following steps.
◆ Press the † or … button to select Channel.
Manual Store
Prog. No
P 1
◆ Press the √ button.
Colour System
AUTO
◆ Press the † or … button to select C (Air channel) or S (Cable
channel).
Sound System
BG
Search
891MHz
Channel
C 16
◆ Press the √ button.
◆ Press the numeric buttons (0~9) to select indicate the required
number.
Fine Tune
no sound or abnormal sound, re-select the sound standard
➣ Ifrequired.
8
If you do not know the channel numbers, select the Search by
pressing the † or … button. Press the √ button to start the
search.
Result:
9
The tuner scans the frequency range until the first
channel or the channel that you selected is received
on your screen.
If reception is weak, you can fine tune a channel manually. Press
the † or … button to select Fine Tune. Press the œ or √ button
until the picture and sound are both clear and sharp.
➢
If you are unable to fine tune a channel, check that the
Colour System and Sound System settings are correct.
œ √ Sel.
Move
Store
Manual Store
Prog. No
P 1
Colour System
AUTO
Sound System
BG
Search
891MHz
Channel
C 16
Fine Tune
œ √ Sel.
Move
Store
Manual Store
Prog. No
P 1
To assign a programme number to a channel, select the Prog.
No by pressing the † or … button. Press the œ or √ button until
you find the correct number.
Colour System
AUTO
11
To store the channel and associated programme number, press
the
button.
Fine Tune
12
Repeat Steps 7 to 11 for each channel to be stored.
10
Sound System
BG
Search
891MHz
Channel
C 16
Move
œ √ Adjust
Fine Tune
☛
Channel mode
◆ P (Programme mode): When completing tuning, the
broadcasting stations in your area have been assigned to
position numbers from P00 to max P99. You can select a
channel by entering the position number in this mode.
Fine Tune
◆ C (Real channel mode): You can select a channel by
entering the assigned number to each air broadcasting station
in this mode.
◆ S (Cable channel mode): You can select a channel by
entering the assigned number for each cable channel in this
mode.
23
Store
Assigning Names to Channels
ENG
Channel names will be assigned automatically when channel
information is broadcast. These names can be changed, allowing
you to assign new names.
Channel
Area
Asia/W.Europe
Auto Store
√
Manual Store
√
Sort
√
Name
√
Edit
√
√ Enter
Move
*
*
*
*
*
C23
*
*
*
*
*
*
*
√ Sel.
Move
Press the MENU button.
The main menu is displayed.
Result:
2
Press the † or … button to select Channel.
The options available in the Channel group are
Result:
displayed.
3
Press the √ button.
4
Press the † or … button to select Name. Press the √ button.
The Name menu is displayed with the current channel
Result:
automatically is selected. Arrow indications are
displayed around the name box.
5
If necessary, select the channel to be assigned a new name by
pressing the † or … button. Press the √ button.
6
Press the † or … button to select a letter (A~Z), a number (0~9)
or a symbol (-, space). Move on the previous or next letter by
pressing the œ or √ button.
7
When you have finished entering the name, press the
to confirm the name.
Return
Name
96
97
98
99
0
1
2
3
4
5
6
7
8
1
Exit
Name
96
97
98
99
0
1
2
3
4
5
6
7
8
Sel.
*
*
*
*
*
C23
*
*
*
*
*
*
*
œ √ Move
24
ABC
Store
button
Activating the Child Lock and Skipping Unwanted Channels
ENG
◆ Activating the child lock
This feature allows you to lock the television so that it cannot
be switched on via the front panel. It can, however, still be
switched on via the remote control. Thus, by keeping the
remote control away from unauthorised users, such as
children, you can prevent them from watching unsuitable
programme.
◆ Skipping unwanted channels
You can exclude the channels of your choice from the
channel scan operation. When you scan through the stored
channels, those that you have chosen to skip are thus not
displayed. All channels that you do not specifically choose to
skip are displayed during scanning.
1
Press the MENU button.
The main menu is displayed.
Result:
2
Press the † or … button to select Channel.
The options available in the Channel group are
Result:
displayed.
3
4
Press the † or … button to select Edit. Press the √ button.
The Edit menu is displayed with the current channel
Result:
automatically is selected.
Press the † or … button to select the channel to be locked.
6
Press the œ or √ button to select Child Lock. To lock the
channel, select On by pressing the † or … button (to unlock the
channel, select Off). Press the
button to confirm.
8
Area
Asia/W.Europe
Auto Store
√
Manual Store
√
Sort
√
Name
√
Edit
√
Move
Press the † or … button to select the channel to be added or
erased.
Press the œ or √ button to select Add/Erase. To add or erase the
channel, select Added or Erased by pressing the † or … button.
Press the
button to confirm.
√ Enter
Return
Edit
96
97
98
99
0
1
2
3
4
5
6
7
8
*
*
*
*
*
*
*
*
*
*
*
*
*
Child Lock
Add
Erase
Off
√ Sel.
Move
Press the √ button.
5
7
Channel
Erased
Exit
Edit
96
97
98
99
0
1
2
3
4
5
6
7
8
*
*
*
*
*
*
*
*
*
*
*
*
*
Child Lock
Off
œ √ Move
Sel.
Erased
Store
Edit
96
97
98
99
0
1
2
3
4
5
6
7
8
Sel.
*
*
*
*
*
*
*
*
*
*
*
*
*
Add
Erase
Off
œ √ Move
25
Erased
Store
Selecting a Channel by Information
ENG
You can display the list of stored channels.
1
Press the CH INFO. button.
Result:
2
Information
96
97
98
99
0
1
2
3
4
5
6
7
8
*
*
*
*
*
*
*
*
*
*
*
*
*
To scroll through the stored channels, press the † or … button.
Result:
3
A list is displayed with the first 13 channels. Two text
boxes to the right of the list indicate:
◆ Whether the Teletext feature is available.
◆ Which sound mode is being used.
The corresponding channel is displayed.
When you are satisfied with your choice, press the MENU (
button to return to normal viewing.
Mono
➢
Move
◆ External inputs can be displayed and scrolled through
in the same way.
Exit
Changing the Picture Standard
You can select the type of picture which best corresponds to your
viewing requirements.
Picture
Mode
œ Dynamic √
Adjust
√
Colour Tone
œ Normal √
Digital NR
Off
Size
Wide
LNA
Off
Move
œ √ Sel.
Return
1
Press the MENU button.
The options available in the Picture group are
Result:
displayed.
2
Press the √ button.
The Mode is selected.
Result:
3
Select the option by pressing the œ or √ button.
The following modes are available depending on the
Result:
input source.
◆ Dynamic - Standard - Movie - Custom
◆ Middle - Low - Custom - High
(PC or DVI Mode)
➣
26
You can also set these options simply by pressing the
P.MODE (Picture Mode) button.
)
Adjusting the Picture Settings
ENG
Your television has several settings which allow you to control
picture quality.
1
Press the MENU button.
Result:
The options available in the Picture group are
displayed.
2
Press the √ button.
3
Press the † or … button to select Adjust. Press the √ button.
Result:
4
5
6
Mode
œ Dynamic √
Adjust
√
Colour Tone
œ Normal √
Digital NR
Off
Size
Wide
LNA
Off
√ Enter
Move
Return
The Adjust menu is displayed.
Press the † or … button to select the option (Contrast,
Brightness, Sharpness, Colour, Tint-NTSC (TV, VIDEO, SVIDEO) only) to be adjusted. Press the œ or √ button
Result:
Picture
The horizontal bar is displayed. Move the horizontal
bar’s cursor left or right by pressing the œ or √ button.
When you are satisfied with the settings, press the
store them.
Adjust (Dynamic)
Contrast
80
Brightness
50
Sharpness
50
Colour
50
button to
œ √ Adjust
Move
Store
Press the MENU button.
Result:
The options available in the Picture group are
displayed again.
7
Press the † or … button to select Colour Tone.
8
Select the option by pressing the œ or √ button. The colour tones
are displayed in the following order.
Picture
Mode
œ Dynamic √
Adjust
√
Colour Tone
œ Normal √
Digital NR
Off
Size
Wide
LNA
Off
Normal - Warm1 - Warm2 - Cool2 - Cool1
Move
➣
√ Enter
If you make any changes to these settings, the picture
standard is automatically switched to the Custom.
27
Return
Adjusting the Picture Settings (PC or DVI Mode)
➢
ENG
1
Preset to the PC or DVI mode by using the SOURCE button.
Press the MENU button.
Picture
Result:
Mode
œ Middle √
Adjust
√
Colour Tone
œ Custom √
Colour Adjust
√
2
Press the √ button.
3
Press the † or … button to select Adjust. Press the √ button.
Result:
√ Enter
Move
Adjust (Middle)
Press the † or … button to select the option (Contrast,
Brightness, Sharpness) to be adjusted. Press the œ or √ button.
Result:
75
Brightness
60
Sharpness
50
5
œ √ Adjust
Store
Picture
Mode
œ Middle √
Adjust
√
Colour Tone
œ Custom √
Colour Adjust
√
œ √ Sel.
Press the † or … button to select Colour Tone.
7
Select the option by pressing the œ or √ button. The colour tones
are displayed in the following order.
Custom (PC mode only) - Colour1 - Colour2 - Colour3
8
Press the † or … button to select Colour Adjust. Press the √
button.
➣
Return
Mode
œ Middle √
Adjust
√
Colour Tone
œ Custom √
Colour Adjust
√
◆ When select the Colour Tone to Custom, the Colour
Adjust menu is displayed.
9
Press the † or … button to select the option (Red, Green, Blue) to
be adjusted. Press the œ or √ button.
Result:
√ Enter
Return
Colour Adjust
Red
50
Green
50
Blue
50
Move
œ √ Adjust
28
The Colour Adjust menu is displayed.
◆ The Colour Adjust menu can not be selected in DVI
mode.
Picture
Move
The options available in the Picture group are
displayed again.
6
Result:
Move
The horizontal bar is displayed. Move the horizontal
bar’s cursor left or right by pressing the œ or √ button.
Press the MENU button.
Result:
Move
The Adjust menu is displayed.
Return
4
Contrast
The options available in the Picture group are
displayed.
Store
10
The horizontal bar is displayed. Move the horizontal
bar’s cursor left or right by pressing the œ or √ button
When you are satisfied with the settings, press the
store them.
button to
Setting the Picture (PC Mode)
➢
1
Preset to the PC mode by using the SOURCE button.
ENG
Press the MENU button.
PC
Result:
2
Press the † or … button to select PC.
Result:
3
6
8
9
√
Frequency
50
Phase
10
Position
√
Size
Wide
Information
√
The Auto Adjustment is selected.
√ Enter
Move
The screen quality and position are automatically reset
with the Auto Adjustment displayed.
PC
Auto Adjustment
√
Frequency
50
Result:
Phase
10
The horizontal bar is displayed. Move the horizontal
bar’s cursor left or right by pressing the œ or √ button.
Position
√
Size
Wide
√
Information
Press the MENU button.
Return
Auto Adjustment
Press the † or … button to select the option (Frequency, Phase)
to be adjusted. Press the œ or √ button.
Result:
7
Auto Adjustment
To adjust the screen quality and position automatically, pressing
the √ button again.
Result:
5
The options available in the PC group are displayed.
Press the √ button.
Result:
4
The main menu is displayed.
√ Enter
Move
The options available in the PC group are displayed
again.
Return
Frequency
Press the † or … button to select Position. Adjust the position
by using the †, …, œ, or √ button. When you are satisfied, press
the
button to store.
50
œ √ Adjust
Return
To select the picture format which best corresponds to your
viewing requirement, select the Size by pressing the † or …
button. Press the √ button.
Phase
Select the option by pressing the œ or √ button. The picture
formats are displayed.
9
œ √ Adjust
Return
Wide - Normal
10
When you are satisfied with the settings, press the
store them.
11
If you get the PC information, select the Information by pressing
the † or … button. Press the √ button.
button to
Position
Adjust
Result:
12
Store
The resolution, vertical frequency and horizontal
frequency are displayed.
When you are satisfied with the settings, press the MENU (
button repeatedly to return to the normal viewing.
Size
)
Wide
œ √ Sel.
Store
PC Information
Resolution
1024x768
V Frequency
60
H Frequency
48
Exit
29
Setting the Picture (Component Mode)
➢
ENG
Function
Language
1
English
Time
√
Blue Screen
Off
Position
√
Phase
√
Recall
√
Press the MENU button.
Result:
2
Return
Position
The options available in the Function group are
displayed.
3
Press the √ button.
4
Press the † or … button to select Position. Press the √ button.
Adjust the position by using the †, …, œ, or √ button. When you
are satisfied with the settings, press the
button to store them.
Adjust
5
Store
The main menu is displayed.
Press the † or … button to select Function.
Result:
√ Enter
Move
Preset to the Component1 or Component2 mode by using the
SOURCE button.
Press the MENU button.
Result:
The options available in the Function group are
displayed again.
Function
Language
Time
√
Blue Screen
Off
Position
√
Phase
√
Recall
√
Move
6
English
Result:
7
Return
8
Phase
œ √ Adjust
9
Exit
Function
English
Time
√
Blue Screen
Off
Position
√
Phase
√
Recall
√
Move
√ Enter
30
Return
The options available in the Function group are
displayed again.
Press the † or … button to select Recall. Press the √ button.
Result:
0
The horizontal bar is displayed. Move the horizontal
bar’s cursor left or right by pressing the œ or √ button.
Press the MENU button.
Result:
√ Enter
Language
Press the † or … button to select Phase. Press the √ button.
The screen quality and position are automatically reset.
When you are satisfied with the settings, press the MENU (
button repeatedly to return to the normal viewing.
)
Extra Picture Settings
ENG
◆ Digital NR
You can activate this feature to reduce any static and
ghosting that may appear on the screen.
◆ Size
You can select the picture format which best corresponds to
your viewing requirements.
Picture
Mode
œ Dynamic √
Adjust
√
Colour Tone
œ Normal √
Digital NR
On
Size
Wide
LNA
Off
Move
◆ LNA (Low Noise Amplifier)
This feature is very useful in the situation that the TV is used
in a weak signal and amplifies the TV signal in the weak
signal area, but not noise.
This feature is working only in a weak signal condition, and
that is memorized on current channel, additional.
➢
Available in TV mode.
Mode
œ Dynamic √
Adjust
√
Colour Tone
œ Normal √
Digital NR
Off
Size
Wide
LNA
Off
Press the MENU button.
The options available in the Picture group are
Result:
displayed.
2
Press the √ button.
3
Select the required option by pressing the † or … button.
4
Press the œ or √ button to change the setting.
Return
Picture
Move
1
œ √ Sel.
√ Enter
Return
Size
Wide
œ √ Sel.
Store
◆ Digital NR : Off or On
TV
◆ Size : Wide - Panorama - Zoom1 - Zoom2 - 14:9 - Normal
➢
You can also select these options simply by pressing the
P.SIZE button on the remote control.
◆ LNA : Off or On
Picture
Mode
œ Dynamic √
Adjust
√
Colour Tone
œ Normal √
Digital NR
Off
Size
Wide
LNA
On
Move
œ √ Sel.
31
Return
Setting the Blue Screen
ENG
If no signal is being received or the signal is very weak, a blue
screen automatically replaces the noisy picture background. If you
wish to continue viewing the poor picture, you must set the “Blue
Screen“ mode to “Off“.
Function
Language
English
Time
√
Teletext Source
Main
Plug & Play
√
Blue Screeen
Off
Move
œ √ Sel.
1
Press the MENU button.
Result:
Return
2
The main menu is displayed.
Press the † or … button to select Function.
Result:
The options available in the Function group are
displayed.
3
Press the √ button.
4
Press the † or … button to select Blue Screen. Press the √
button.
5
Press the œ or √ button to change the setting. (On or Off).
Selecting the Film Mode (Video or S-Video Mode only)
You can automatically sense and process film signals from all
sources and adjust the picture for optimum quality.
Picture
Mode
œ Standard √
Adjust
√
Colour Tone
œ Normal √
Digital NR
On
Size
Auto Wide
Film Mode
Off
Move
œ √ Sel.
1
Press the MENU button.
Result:
The options available in the Picture group are
displayed.
2
Press the √ button.
3
Press the † or … button to select Film Mode Press the √ button.
4
Press the œ or √ button to change the setting. (Off or On).
Return
◆ On : Automatically senses and processes film signals from all
sources and adjusts the picture for optimum quality.
◆ Off : Switches off the Film Mode.
➢
32
Film mode is supported in Video, S-Video, Component 480i.
DNIeTM (Digital Natural Image engine)
ENG
This feature bring you more detailed image with 3D noise
reduction, detail enhancement, contrast enhancement and white
enhancement. New image compensation Algorithm gives brighter,
clearer, much detailed image to you. DNIeTM technology will fit
every signals into your eyes.
Press the DNIe button repeatedly to select the following options.
◆ On : Switches on the DNIe mode.
◆ Off : Switches off the DNIe mode.
DNIe On
◆ Demo (Option) : The screen before applying DNIe appears on the
right and the screen after applying DNIe appears
on the left.
Freezing the Current Picture
You can freeze the picture when watching a television programme
simply by pressing the “STILL” button. To return to normal viewing,
press it again.
➣
In the PIP mode, the main and sub pictures are stilled at
the same time.
33
Changing the Sound Standard
ENG
You can select the type of special sound effect to be used when
watching a given broadcast.
Sound
œ Standard √
Mode
Equalizer
√
Auto Volume
Off
Melody
Off
Pseudo Stereo
Off
Virtual Surround
Off
1
Result:
2
œ √ Sel.
Move
Press the MENU button.
Press the † or … button to select Sound.
Result:
Return
The main menu is displayed.
The options available in the Sound group are displayed.
3
Press the √ button.
The Mode is selected.
Result:
4
Select the option by pressing the œ or √ button. The sound
effects are displayed in the following order.
Standard - Music - Movie - Speech - Custom
Adjusting the Sound Settings
The sound settings can be adjusted to suit your personal preferences.
Sound
Mode
œ Standard √
Equalizer
√
Auto Volume
Off
Melody
Off
Pseudo Stereo
Off
Virtual Surround
Off
Move
1
Press the MENU button.
Result:
2
Press the † or … button to select Sound.
Result:
√ Enter
Return
The main menu is displayed.
The options available in the Sound group are displayed.
3
Press the √ button.
4
Press the † or … button to select Equalizer. Press the √ button.
Equalizer (Standard)
Result:
10
R
5
Select the option (volume, balance, equalizer) to be adjusted by
pressing the œ or √ button. Press the † or … button to reach the
required setting.
6
When you are satisfied with the settings, press the
store them.
L
100 300
œ √ Move
Adjust
1K
3K
10K
Store
➣
34
The Equalizer menu is displayed with the current
option.
button to
If you make any changes to the equalizer settings, the
sound standard is automatically switched to the Custom.
Extra Sound Settings
ENG
◆ Auto Volume
Each broadcasting station has its own signal conditions,
and so it is not easy for you to adjust the volume every
time the channel is changed. This feature lets you
automatically adjust the volume of the desired channel by
lowering the sound output when the modulation signal is
high or by raising the sound output when the modulation
signal is low.
Sound
œ Standard √
Mode
Equalizer
√
Auto Volume
Off
Melody
Off
Pseudo Stereo
Off
Virtual Surround
Off
œ √ Sel.
Move
Return
◆ Melody
You can hear clear melody sound when the television is
powered on or off.
Sound
œ Standard √
Mode
◆ Pseudo Stereo / Virtual Surround
Pseudo stereo feature converts a monaural sound
signal into two identical left and right channels.
Once the Pseudo stereo or Virtual surround is set
to On or Off, these settings apply to the sound effects
such as Standard, Music, Movie, and Speech.
Equalizer
√
Auto Volume
Off
Melody
Off
Pseudo Stereo
Off
Virtual Surround
Off
œ √ Sel.
Move
Return
Sound
1
2
Press the MENU button.
The main menu is displayed.
Result:
Press the † or … button to select Sound.
The options available in the Sound group are displayed.
Result:
3
Select the required option by pressing the † or … button.
4
Press the œ or √ button to change the setting. (Off or On).
œ Standard √
Mode
Equalizer
√
Auto Volume
Off
Melody
Off
Pseudo Stereo
Off
Virtual Surround
Off
œ √ Sel.
Move
Return
Sound
œ Standard √
Mode
Equalizer
√
Auto Volume
Off
Melody
Off
Pseudo Stereo
Off
Virtual Surround
Off
Move
œ √ Sel.
35
Return
Selecting the DUAL Mode (depending on the model)
ENG
The “Dual I- II” button displays/controls the processing and output
of the audio signal. When power is switched on, the mode is
automatically preset to either “Dual-I ” or “Stereo”, depending on
the current transmission.
NICAM
Stereo
Type of broadcast
On-screen indication
Regular broadcast
(Standard audio)
Mono (Normal use)
Regular +
NICAM Mono
NICAM Mono ↔ Mono
NICAM Stereo
A2
Stereo
NICAM Dual-I/II
NICAM Dual-I →
NICAM Dual-II →
Mono
Regular broadcast
(Standard audio)
Mono
Bilingual or Dual-I/II
Dual-I ↔ Dual-II
Stereo
➣
NICAM Stereo ↔ Mono
(Forced mono)
Stereo ↔ Mono
(Forced mono)
◆ If the receiving conditions deteriorate, listening will be
easier if the mode is set to the Mono.
◆ If the stereo signal is weak and an automatic switching
occurs, then switch to the Mono.
◆ When receiving a mono sound in the AV mode, connect
to the “AUDIO-L” input connector on the side of the
television. If the mono sound comes out only from left
speaker, press the DUAL I-II button.
36
Setting the Time and Switching the TV On/Off Automatically
ENG
You can set the television’s clock and set the On or Off timers so
that the television will switch on or off automatically at the time
you select.
Function
Language
1
2
Press the MENU button.
The main menu is displayed.
Result:
√
Teletext Source
Main
Plug & Play
√
Blue Screen
Off
Press the † or … button to select Function.
The options available in the Function group are
Result:
displayed.
3
Press the √ button.
4
Press the † or … button to select Time. Press the √ button.
The Time menu is displayed with the Clock option
Result:
selected.
5
Set the clock by pressing the numeric buttons.
6
Press the † or … button to select Timer. Set to On by pressing the
œ or √ button. for switching on automatically.
➣
If you have not set the clock, you can not select the Timer.
English
Time
Move
√ Enter
Time
--:--
Clock
Timer
Off
On Time
--:--
Off Time
--:--
Move
Adjust
8
Press the † or … button to select On Time. Set the time to switch
on automatically by pressing the numeric buttons.
In the same way, set the Off Time to switch off automatically.
Store
Time
Clock
11:35
Timer
7
Return
On
On Time
--:--
Off Time
--:--
Move
œ √ Sel.
Store
Time
Clock
11:35
Timer
On
On Time
06:30
Off Time
--:--
Move
Adjust
Store
Time
Clock
11:35
Timer
On
On Time
06:30
Off Time
23:00
Move
Adjust
37
Store
Setting the Sleep Timer
ENG
You can select a time period of between 15 and 180 minutes after
which the television automatically switches to Standby mode.
TV
1
Press the SLEEP button.
The Sleep timer menu is displayed.
Result:
◆ If the sleep timer is not yet set, Off is displayed.
If the sleep timer is already set, the remaining time
before which the television switches to Standby
mode is displayed.
2
Select the preset time intervals (15, 30, 45, 60, 75, 90, 105, 120,
135, 150, 165, 180) by pressing the œ or √ button.
3
Press the
Sleep timer
Off
œ √ Sel.
Store
38
button to confirm your selection.
Viewing the Picture In Picture (PIP)
ENG
You can display a sub picture within the main picture of TV
program or external A/V devices. In this way you can watch TV
program or monitor the video input from any connected devices
while watching TV or other video input.
1
Press the MENU button.
Result:
2
The main menu is displayed.
PIP
On
Sel.
TV
Swap
√
Size
Large
Prog. No
P01
Press the † or … button to select PIP.
Result:
4
To activate, set the PIP to on by pressing the œ or √ button.
Press the † or … button to select Sel.. Select a source of the sub
picture by pressing the œ or √ button.
PIP
On
Sel.
TV
Swap
√
Size
Large
Prog. No
P01
The sources are displayed in the following order:
➣
◆ The PC, Component1, Component2 can not
be selected in DVI mode.
◆ The DVI, Component1, Component2 can not
be selected in PC mode.
◆ The PC, DVI, Component2 can not be
selected in Component1 mode.
Return
PIP
PIP
On
Sel.
TV
Swap
√
Size
Large
Prog. No
P01
◆ The PC, DVI, Component1 can not be
selected in Component2 mode.
√ Enter
Move
Return
Press the † or … button to select Swap. Press the œ or √ button.
Result:
7
œ √ Sel.
Move
TV - Video - S-Video - Component1 Component2 - PC - DVI
6
Return
PIP
Press the √ button.
Result:
œ √ Sel.
Move
The options available in the PIP group are displayed.
3
5
PIP
Press the † or … button to select Size. Select a size of the sub
picture by pressing the œ or √ button.
Result:
PIP
The main picture and sub picture are interchanged.
The sizes are displayed in the following order:
PIP
On
Sel.
TV
Swap
√
Size
Large
Prog. No
P01
Large - Small - Double1 - Double2 - 12PIP
◆ 12PIP : Used to view up to 12 memorized
channels on the sub picture
spontaneously.
available in Component1,
➣ Not
Component2, PC or DVI mode.
8
Press the † or … button to select Prog.No.. Select the channel
that you want to view through sub picture by pressing the œ or √
button.
œ √ Sel.
Move
Return
PIP
PIP
On
Sel.
TV
Swap
√
Size
Large
Prog. No
P01
œ √ Sel.
Move
39
Return
Viewing the Picture In Picture (PIP) (continued)
ENG
Easy functions of remote control.
40
Buttons
Feature
PIP ON
Used to activate or deactivate the PIP function directly.
LOCATE
Used to move the sub picture counterclockwise.
P
Used to select the channel of sub picture.
/
SCAN
Used to scan every memorized channel in order.
To stop scanning, press it again.
SOURCE
Used to assign a source of sub picture
(TV, Video, S-Video, Component1, Component2, PC,
DVI).
Listening to the Sound of the Sub Picture (PC or DVI Mode)
➢
Preset to the PC or DVI mode by using the SOURCE button.
ENG
During the PIP feature is activating, you can listen to the sound of the
sub picture.
1
Press the MENU button.
Result:
2
The main menu is displayed.
Press the † or … button to select PIP.
Result:
PIP
PIP
On
Sel.
TV
Swap
√
Size
Large
Sound Sel.
Sub
The options available in the PIP group are displayed.
œ √ Sel.
Move
3
Press the √ button.
4
Press the † or … button to select Sound Sel.. Set to Sub by
pressing the œ or √ button.
Result:
➣
You can listen to the sound of the sub picture.
To listen the sound of current main picture, set to Main.
41
Return
Teletext Feature
ENG
Most television channels provide written information services via
teletext. Information provided includes:
◆ Television programme times
◆ News bulletins and weather forecasts
◆ Sports results
◆ Travel information
This information is divided into numbered pages (see diagram).
Part
Contents
A
Selected page number.
B
Broadcasting channel identity.
C
Current page number or search indications.
D
Date and time.
E
Text.
F
Status information.
FASTEXT information.
➣
Teletext information is often divided between several
pages displayed in sequence, which can be accessed by:
◆ Entering the page number
◆ Selecting a title in a list
◆ Selecting a coloured heading (FASTEXT system)
42
Displaying the Teletext Information
ENG
You can display Teletext information at any time on your television
Teletext information to be displayed correctly,
☛ For
channel reception must be stable; otherwise:
◆ Information may be missing
◆ Some pages may not be displayed
1
Select the channel providing the Teletext service by pressing the
P
or
button.
2
Press the TTX/MIX button to activate the teletext mode.
Result:
The contents page is displayed. It can be redisplayed
at any time by pressing the
(index) button.
3
Press the TTX/MIX button again.
The screen will be split into two. This Double Teletext
Result:
feature lets you view the actual broadcast and teletext
information separately on the screen.
4
If you wish to display the current input source and teletext page
on a single screen, press the TTX/MIX button again.
5
To exit from the teletext display, press the TTX/MIX button again.
Selecting Display Options
When you have displayed a Teletext page, you can select various
options to suit your requirements.
To display...
Press the...
◆ Hidden text
(answers to quiz games, for example)
(reveal)
◆ The normal screen
(reveal) again
◆ A secondary page by entering its number
(sub-page)
◆ The broadcast when searching for a page
(cancel)
◆ The next page
(page up)
◆ The previous page
(page down)
◆ Double-size letters in the:
• Upper half of the screen
• Lower half of the screen
(size)
• Once
• Twice
◆ The normal screen
• Three times
43
Selecting the Teletext Source (Option)
ENG
When you watching the current channel you can display the
Teletext information of other channel.
Function
Language
English
Time
√
Teletext Source
Main
Plug & Play
√
Blue Screen
Off
œ √ Sel.
Move
1
Result:
English
Time
√
Teletext Source
Sub
Plug & Play
√
Blue Screen
Off
œ √ Sel.
Move
The main menu is displayed.
2
Press the † or … button to select Function.
The options available in the Function group are
Result:
displayed.
3
Press the √ button.
4
Press the † or … button to select Teletext Source.
5
Select the required option (Main or Sub) by pressing the œ or √
button.
Return
Function
Language
Press the MENU button.
◆ If you set to Main, you can display the teletext information of
current channel.
Return
◆ If you set to Sub, you can display the teletext information of
other channel.
- If the PIP feature is activating, you can display the teletext
information of sub channel. If change the channel of sub
picture, you can display the teletext information of the
changed sub channel.
- If the Double Teletext feature is activating, you can display
the teletext information of other channel at the same time as
the current channel.
44
Selecting a Teletext Page
ENG
You can enter the page number directly by pressing the numeric
buttons on the remote control.
1
Enter the three-digit page number given in the content by
pressing the corresponding numeric buttons.
Result:
The current page counter is incremented and the
page is then displayed. If the selected page is linked
with several secondary pages, the secondary pages
are displayed in sequence.
2
If the FASTEXT system is used by the broadcasting company,
the different topics covered on a Teletext page are colour-coded
and can be selected by pressing the coloured buttons on the
remote control.
Press the coloured button corresponding to the topic that you wish
to select; the available topics are given on the status line.
Result:
The page is displayed with other coloured information
that can be selected in the same way.
3
To display the previous or next page, press the corresponding
coloured button.
4
To display the subpage, see the following steps.
◆ Press the
(sub-page) button.
The available subpages appear.
Result:
◆ Select the required sub-page. Sub-pages can be scrolled by
pressing the
or
button.
5
When you have finished, press the EXIT (
your normal broadcast.
) button to return to
45
TeleWeb Feature (Option)
ENG
TeleWeb is the new television broadcasting standard for Teletext
services. TeleWeb is similar to Teletext, just easy to use. TeleWeb
can transmit the News, TV programme information, and advertising
in excellent picture quality and directly access via the remote
control.
Function
Language
English
Time
√
Teleweb
√
Plug & Play
√
Blue Screen
Off
√ Enter
Move
Return
1
Press the MENU button.
The main menu is displayed.
Result:
2
Press the † or … button to select Function.
The options available in the Function group are
Result:
displayed.
3
Press the √ button.
4
Press the † or … button to select Teleweb. Press the √ button.
The Teleweb menu is displayed.
Result:
5
To activate the Teleweb feature, set the Teleweb to On by
pressing the œ or √ button.
◆ If you set to On, 400 teletext pages can be stored.
◆ If you set to Off, 2100 teletext pages can be stored.
6
Press the † or … button to select Provider Search. Start the
provider search by pressing the œ or √ button.
It will be search only the channels stored. If find a
Result:
provider, the Added is displayed and continue the
search.
Teleweb Setting
Teleweb
On
Provider Search
√
Provider Select
-- ----- ----------
Download
Off
œ √ Sel.
Move
Return
Teleweb Setting
Teleweb
On
Provider Search
√
Provider Select
-- ----- ----------
Download
Off
√ Enter
Move
Return
➢
To stop the search before it has finished, press the TV
button.
Provider Search
7
2%
P1 -----
Added
➢
Exit
Teleweb Setting
Teleweb
On
Provider Search
√
Provider Select
P3 KABEL Service 15
Download
Off
œ √ Sel.
Move
Return
Teleweb Setting
Teleweb
On
√
Provider Select
P3 KABEL Service 15
Download
On
œ √ Sel.
46
Return
Select a provider and then the teleweb downloading will start.
8
Press the TeleWeb button to enter the teleweb mode.
9
If you want to download the Teleweb information before switch the
television off, select the Download by pressing the † or … button.
Press the † or … button to set to On.
Even though you turn off the TV on the channel no
Result:
provider is selected, the channel will be automatically
switched to the selected channel and TeleWeb
downloading will start. During downloading, the picture
will not be shown and only status bar will be displayed
on the screen. (It takes 30 minutes to one hour
depending on the program.)
➣
Provider Search
Move
When the search has been finished, press the † or … button to
select Provider Select. Find the required provider by pressing
the œ or √ button.
◆ When pressing the “ I ” button (On/Off) on the panel
of the television, the existing downloaded information
will disappear.
◆ If you enter the TeleWeb mode on the channel where
no provider is selected, you can view only the
information downloaded up to now.
Using the TeleWeb Menu after Displaying the TeleWeb
ENG
Bookmarking the current page.
TeleWeb
1
On the page you wish to add to the bookmark list press the MENU
button.
Result:
2
The TeleWeb menu is displayed.
Press the † or … button to select Add Bookmark.
Press the
button.
Result:
➢
Bookmark List
√
Add Bookmark
√
Home Page
√
Current program
*
Selected provider
*
The current page is added to the bookmark list.
You can register up to six pages. If you add another URL
when six bookmarks have been listed, the first URL will be
deleted and the new URL will be listed as the sixth.
Service is loading
√ Enter
Move
Return
TeleWeb
Entering the bookmarked URL.
1
The TeleWeb menu is displayed with the Bookmark
List is selected.
Press the √ button.
Result:
3
√
√
Home Page
√
Press the MENU button.
Result:
2
Bookmark List
Add Bookmark
Current program
*
Selected provider
*
Service is loading
√ Enter
Move
Return
The stored URLs are listed.
To erase a URL, select a required URL and press the TeleWeb
button.
SAMSUNG ELECTRONICS
Result:
TARA SYSTEMS
The selected URL is erased and the listed URLs
moves up one by one.
Bookmark List
KIA MOTORS
MICRONAS
4
Select the URL you wish to enter by pressing the † or … button
and press the
button
Result:
The current page moves to the selected URL and the
menu is disappeared.
OLYMPIC NEWS
ECONOMICS
Move
Erase
√ Enter
TeleWeb
Opening the Home Page
1
Press the MENU button.
Result:
2
The TeleWeb menu is displayed.
Press the † or … button to select Home Page.
Press the
button.
Result:
Bookmark List
√
Add Bookmark
√
Home Page
√
Current program
*
Selected provider
*
Service is loading
Move
√ Enter
It moves to a home page.
47
Return
Easy Accessing the TeleWeb Service via the Remote Control
ENG
Button
TeleWeb
HOME
Function
Activate or deactivate the TeleWeb feature directly.
Move the home page of the TeleWeb.
Dispaly the forward page of the TeleWeb
Dispaly the backward page of the TeleWeb
Select a option.
Confirm your choice.
Viewing Pictures From External Sources
Once you have connected up your various audio and video systems,
you can view different sources by selecting the appropriate input.
AV Input
TV
Video
S-Video
Component1
Component2
PC
DVI
Not Connected
Not Connected
Not Connected
Not Connected
Connected
Not Connected
Sel.
Store
48
1
Check that all the necessary connections have been made.
2
Switch your television on, then press the SOURCE (
Result: The input sources available are displayed.
3
Press the † or … button to select the required input source and
press the
button.
➣
) button.
If you change the external source while viewing, pictures
might take a short period of time to be switched.
Connecting to the External Devices
ENG
“MONITOR OUT” are used for the equipment with an RGB output, such as video game devices or
video disc players.
Rear of the TV
(Output)
VCR
②
①
DVD
Decoder /
Video game device
Rear of the TV
(Input)
③
Video disc player
A
Satellite receiver
① This end can be fitted with three RCA connectors (VIDEO + AUDIO-L and R)
② If you have a second VCR and wish to copy cassettes tape, connect the source VCR to “A” and the
target VCR to “MONITOR OUT” so that you can redirect the signal from source VCR to target VCR.
③ If you have a decoder, connect the decoder to the VCR and the VCR to the TV.
➃ “MONITOR OUT” is used for displaying the current picture to an external device. When you wish to
record the current picture, connect the VCR to “MONITOR OUT”.
☛
Whenever you connect an audio or video system to your television,
ensure that all elements are switched off. Refer to the documentation
supplied with your equipment for detailed connection instructions
and associated safety precautions.
49
Connecting to the DVD Input
ENG
The RCA connectors are used for equipment with a DVD output. (480i/480p/576i/576p/720p/1080i)
Rear of the TV
Y / Pb / Pr
DVD
L/R
Connecting to the S-Video Input
The S-VIDEO and RCA (AUDIO-L/R) connectors are used for equipment with an S-Video output,
such as a camcorder or VCR.
Rear of the TV
Camcorder
①
and
① To play picture and sound, both the S-VIDEO and RCA connectors must be used.
50
VCR
Connecting to the DVI Input
ENG
The “DVI IN” (video) and “AUDIO” connectors are used for equipment with a DVI output.
Rear of the TV
Personal Computer
and
Connecting to the PC Input
The “PC IN (RGB IN)” (video) and “AUDIO” connectors are used for interfacing with your PC.
Rear of the TV
Personal Computer
and
51
Setting up Your PC Software (Windows only)
ENG
The Windows display-settings for a typical computer are shown below. But the actual screens on your
PC will probably be different, depending upon your particular version of Windows and your particular
video card. But even if your actual screens look different, the same, basic set-up information will apply
in almost all cases. (If not, contact your computer manufacturer or Samsung Dealer.)
On the windows screen, select in the following
sequence: Start ➞ Settings ➞ Control Panel.
When the control panel screen appears, click on
Display and a display dialog-box will appear.
Select the Settings tab in the display dialog-box.
The two key variables that apply the television-PC
interface are “Resolution” and “Colours”.
The correct settings for these two variables are:
◆ Size (sometimes called “Resolution”)
- 640 x 480 pixels (PS42P3S)
- 1024 x 768 pixels (PS50P3H/PS63P3H)
◆ Colour
24-bit colour (might also be expressed as “16
million colours”)
Shown at left is a typical screen for “Display”
dialog box.
If a vertical-frequency option exists on your display
settings dialog box, the correct value is 60 Hz.
Otherwise, just click OK and exit the dialog box.
52
Input Mode (PC/DVI)
ENG
Both screen position and size will vary depending on the type of PC monitor and its resolution.
The table below shows all of the display modes that are supported:
Standard
Dot x Line
VGA
640 x 350
640 x 400
720 x 400
640 x 480
SVGA
800 x 600
XGA
1024 x 768
WVGA
848 x 480
WXGA+
(PS50/63P3H)
1366 x 768
◆
◆
◆
◆
Vertical
frequency (Hz)
Horizontal
frequency (kHz)
Vertical
polarity
Horizontal
polarity
75
85
85
70
85
60
72
75
85
56
60
72
75
85
60
70
75
60
72
75
31.5
37.9
37.9
31.5
37.9
31.5
37.9
37.5
43.3
35.2
37.9
48.1
46.9
53.7
48.4
56.5
60.0
29.8
35.1
36.0
N
N
P
P
P
N
N
N
N
N/P
P
P
P
P
N
N
P
N
N
N
P
P
N
N
N
N
N
N
N
N/P
P
P
P
P
N
N
P
P
P
P
60
48.2
N
N
(N: Negative / P: Positive)
The interlace mode is not supported.
The television might operate abnormally if a non-standard video format is selected.
”1366 x 768” is not available in DVI mode.
The 1366 x 768 mode is only supported by a particular video card (PIXEL PERFECT made by IMAGINE
GRAPHICS Ltd.).
Notes
◆ The PC text quality for PS42P3S is optimum in VGA mode (640 x 480). For PS50P3H and PS63P3H, use
XGA mode (1024 x 768).
◆ When this television is used as a PC display, 24-bit colour is supported (over 16 million colours).
◆ Your PC display screen might appear different depending on the manufacturer (and your particular version of
Windows). Check your PC instruction book for information about connecting your PC to a television.
◆ If a vertical and horizontal frequency-select mode exists, select 60Hz (vertical) and 31.5kHz (horizontal).
In some cases, abnormal signals (such as stripes) might appear on the screen when the PC power is turned
off (or if the PC is disconnected). If so, press the Source button to enter the Video mode. Also, make sure that
the PC is connected.
◆ When connecting a notebook PC to the television, make sure that the PC screen is displayed through only the
television (Otherwise, random signals might appear).
◆ When horizontal synchronous signals seem irregular in PC mode, check PC power saving mode or cable
connections.
53
Pin Configurations
ENG
PC Input Connector
(15Pin)
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
54
DVI Input Connector
(24Pin)
PC IN
Red (R)
Green (G)
Blue (B)
Grounding
Grounding (DDC)
Red (R) Grounding
Green (G) Grounding
Blue (B) Grounding
Reserved
Sync Grounding
Grounding
Data (DDC)
Horizontal sync.
Vertical sync.
Clock (DDC)
Pin
Signal
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
T.M.D.S. Data2T.M.D.S. Data2+
T.M.D.S. Data2/4 Shield
T.M.D.S. Data4T.M.D.S. Data4+
Clock (DDC)
Data (DDC)
Not Connected
T.M.D.S. Data1T.M.D.S. Data1+
T.M.D.S. Data1/3 Shield
T.M.D.S. Data3T.M.D.S. Data3+
+5V Power
5V Grounding
Hot Plug Detect
T.M.D.S. Data0T.M.D.S. Data0+
T.M.D.S. Data0/5 Shield
T.M.D.S. Data5T.M.D.S. Data5+
T.M.D.S. Clock Shield
T.M.D.S. Clock+
T.M.D.S. Clock-
Troubleshooting: Before Contacting Service Personnel
ENG
Before contacting Samsung after-sales service, perform the following simple checks.
If you cannot solve the problem using the instructions below, note the model and serial number of the
television and contact your local dealer.
No sound or picture
◆ Check that the mains lead has been connected to a wall socket.
◆ Check that you have pressed the “ I ” button (On/Off) and the
POWER ( ) button.
◆ Check the picture contrast and brightness settings.
◆ Check the volume.
Normal picture but no sound
◆ Check the volume.
◆ Check whether the volume MUTE button on the remote control has
been pressed.
No picture or black and white picture
◆ Adjust the colour settings.
◆ Check that the broadcast system selected is correct.
Sound and picture interference
◆ Try to identify the electrical appliance that is affecting the television,
then move it further away.
◆ Plug your television into a different mains socket.
Blurred or snowy picture,
distorted sound
◆ Check the direction, location and connections of your aerial.
This interference often occurs due to the use of an indoor aerial.
Remote control malfunctions
◆ Replace the remote control batteries.
◆ Clean the upper edge of the remote control (transmission window).
◆ Check the battery terminals.
55
- AFTER SALES SERVICE
- Do not hesitate to contact your retailer or service agent
if a change in the performance of your product indicates
that a faulty condition may be present.
ELECTRONICS
BN68-00481A-00
Download PDF