SyncMaster LD190/LD190G/LD220/LD220G
LCD Monitor
User Manual
Safety Instructions
Notational
Note
These safety instructions must be followed to ensure your safety and prevent property damage.
Make sure to read the instructions carefully and use the product in the correct manner.
Warning / Caution
Otherwise, it may result in death or personal injury.
Otherwise, it may result in personal injury or property damage.
Notational Conventions
Prohibited
Important to read and understand at all times
Do not disassemble
Disconnect the plug from the
outlet
Do not touch
Ground to prevent an electric
shock
Power
When not used for extended period of time, set your computer to DPM.
If using screen saver, set it to active screen mode.
The images here are for reference only, and are not applicable in all cases
(or countries).
Shortcut to Anti-Afterimage Instructions
Do not use a damaged power cord or plug or a damaged or
loose power outlet.
•
Otherwise, this may result in electric shock or fire.
Do not touch the power plug with wet hands when removing or
plugging the plug into the outlet.
•
Otherwise, this may result in electric shock.
Make sure to connect the power cord to a grounded power outlet.
•
Otherwise, it may result in electric shock or personal injury.
Safety Instructions
Ensure that the power plug is plugged into the power outlet
firmly and correctly.
•
Otherwise, this may result in fire.
Do not forcefully bend or pull the power plug and do not place
any heavy material on it.
•
Otherwise, this may result in fire.
Do not connect multiple appliances to the same power outlet.
•
Otherwise, this may cause fire due to overheating.
Do not disconnect the power cord while using the product.
•
Otherwise, this may result in damage to the product due to
electric shock.
To disconnect the apparatus from the mains, the plug must be
pulled out from the mains socket, therefore the mains plug shall
be readily operable.
•
This may cause electric shock or fire.
Use only the power cord provided by our company. Do not use
the provided power cord of another product.
•
Otherwise, this may result in fire or electric shock.
Installation
Be sure to contact an authorized Service Center when installing your
monitor in a location with heavy dust, high or low temperatures, high humidity, and exposed to chemical substances and where it operates for 24
hours such as at airports, train stations etc.
Failure to do so may cause serious damage to your monitor.
Do not drop the monitor when moving it.
•
This may cause damage to the product or the person carrying
it.
When installing the product in a cabinet or rack, make sure that
the front end of the bottom of the product does not project out.
•
Otherwise, it may fall or cause personal injury.
•
Use a cabinet or rack of a size appropriate to the product.
DO NOT PLACE CANDLES, MOSQUITO REPELLANT, CIGARETTES AND ANY HEATING APPLIANCES NEAR THE
PRODUCT.
•
Otherwise, this may result in fire.
Safety Instructions
Keep heating appliances as far away from the power cord or the
product as possible.
•
Otherwise, this may result in electric shock or fire.
Do not install it in a badly ventilated location such as a bookcase
or closet.
•
Otherwise, this may result in fire due to an increase in the internal temperature.
Put down the monitor carefully.
•
Failing to do so may damage the monitor.
Do not place the front of the product on the floor.
•
Otherwise, this may result in damage to the screen display.
Install your product in a well ventilated location. Ensure that
there is a clearance of more than 10 cm from the wall.
•
Otherwise, it may result in fire due to an increase in the internal
temperature.
Ensure that the packaging vinyl is kept away from children.
•
Otherwise, it may result in serious harm (suffocation) if children
play with it.
Clean
When cleaning the monitor case or the surface of the TFT-LCD screen,
wipe with a slightly moistened, soft fabric.
Do not spray cleaner directly onto the surface of the product.
•
Otherwise, this may result in the discoloration and distortion of
the structure and the screen surface may peel off.
Clean the product using a soft cloth with a monitor cleaner only.
If you must use a cleaner other than the monitor cleaner, dilute it
with water at a ratio of 1:10.
When cleaning the power plug pins or dusting the power outlet,
clean it with a dry cloth.
•
Otherwise, it may result in fire.
When cleaning the product, make sure to disconnect the power
cord.
•
Otherwise, it may result in electric shock or fire.
Safety Instructions
When cleaning the product, disconnect the power cord and
clean it softly with a dry cloth.
•
(Do not use chemicals such as wax, benzene, alcohol, thinner,
mosquito repellant, lubricant, or cleaner.) These may change
the appearance of the product surface and peel off the indication labels on the product.
Since the product housing is easily scratched, make sure to use
the specified cloth only.
•
Use the specified cloth adding only a little water. As the product
may be scratched if there is any foreign material on the cloth,
make sure to shake it thoroughly before using it.
When cleaning the product, do not spray water directly onto the
main body of the product.
•
Ensure that water does not enter the product and that it is not
wet.
•
Otherwise, this may result in electric shock, fire or a malfunction.
Others
The product is a high voltage product. Ensure that users do not
disassemble, repair or modify the product themselves.
•
Otherwise, this may result in electric shock or fire. If the product
needs to be repaired, contact a Service Center.
If there is a strange smell or a strange sound or smoke is coming
from the product, disconnect the power plug immediately and contact a Service Center.
•
Otherwise, this may result in electric shock or fire.
Do not place this product in a location exposed to moisture, dust,
smoke, water, or in a car.
•
Otherwise, this may result in electric shock or fire.
When you drop the product or the case is broken, turn the power
off and disconnect the power cord. Contact a Service Center.
•
Otherwise, this may result in electric shock or fire.
If thunder or lightening is occurring, do not touch the power cord
or antenna cable.
•
Otherwise, this may result in electric shock or fire.
Do not try to move the monitor by pulling only the wire or the
signal cable.
•
Otherwise, it may fall and result in electric shock, damage to
the product or fire due to damage to the cable.
Safety Instructions
Do not lift or move the product back and forwards or right and
left while only holding the power cord or signal cables.
•
Otherwise, it may fall and result in electric shock, damage to
the product or fire due to damage to the cable.
Make sure that the ventilating opening is not blocked by a table
or curtain.
•
Otherwise, it may result in fire due to an increase in the internal
temperature.
Do not place any containers containing water, vases, flowerpots, medicines as well as any metal on the product.
•
If water or a foreign material enters the product, disconnect the
power cord and contact a Service Center.
•
This may result in a product malfunction, electric shock, or fire.
Do not use or keep combustible spray or flammable material
near the product.
•
Otherwise, this may result in an explosion or fire.
Do not insert any metal, such as chopsticks, coins, pins and
steel, or flammable objects, such as matches or paper, inside the
product (through the ventilating openings, input and output terminals, etc).
•
If water or foreign material enters the product, disconnect the
power cord and contact a Service Center.
•
Otherwise, this may result in electric shock or fire.
When using a fixed screen for a long time, an afterimage or stain
may occur.
•
If you are not using your product for a long period of time, put
it into sleep mode or use a moving screen saver.
Set a resolution and frequency appropriate to the product.
•
Otherwise, your eyesight may be damaged.
If you continually move closer to the product screen, your eyesight may be failing.
To ease eye strain, take at least a five-minute break after every
hour of using the monitor.
Do not install it in an unstable location such as an unstable rack
or uneven surface or a location exposed to vibrations.
•
Otherwise, it may fall and cause personal injury and/or damage
the product.
Safety Instructions
•
If you use the product in a location exposed to vibrations, it may
damage the product and result in fire.
When moving the product, turn the power off and disconnect
the power plug, antenna cable, and all the cables connected to the
product.
•
Otherwise, it may result in electric shock or fire.
Ensure that children do not hang onto the product or climb up
onto the product.
•
The product may fall and cause personal injury or death.
If you do not use the product for a long period of time, disconnect
the power cord from the power outlet.
•
Otherwise, this may result in overheating or fire due to dust,
and may result in fire due to electric shock or leakage.
Do not place any heavy items or toys or confectionery, such as
cookies etc. that may attract the attention of children and to the
product.
•
Your children may hang onto the product causing it to fall and
this may result in personal injury or death.
Do not turn the product upside down or move it while holding
only the stand.
•
Otherwise, it may fall and result in personal injury and/or damage to the product.
Do not place the product in a location exposed to direct sunlight
or near any heat such as a fire or heater.
•
This may reduce the lifetime of the product, and may result in
fire.
Do not drop any objects onto the product or cause any impact
to the product.
•
Otherwise, this may result in electric shock or fire.
Do not use a humidifier or kitchen table near the product.
•
Otherwise, this may result in electric shock or fire.
When there is a gas leak, do not touch the product or the power
plug but ventilate immediately.
•
If a spark occurs, it may cause an explosion or fire.
If the product has been turned on for a long time, the display
panel becomes hot. Do not touch it.
•
Keep the small accessories in a location out of the reach of
children.
Safety Instructions
Do not install the product in a location low enough for children
to reach.
•
Otherwise, it may fall and result in personal injury.
•
Since the front part of the product is heavy, install the product
on a level and stable surface.
Do not put any heavy objects on the product.
•
This may result in personal injury and/or damage to the product.
Good Postures When Using the Monitor
When using the product, use it in the correct position.
•
Keep your back straight while looking at the product.
•
The distance between your eyes and the screen
should be between 45 to 50 cm. Look at the screen
from a slightly higher location than the height of the
screen.
•
When using the product, use it in the correct position.
•
Adjust the angle so that light is not reflected on the
screen.
•
Place your arms perpendicular to your sides and
allow your arms to be level with the back of the
hand.
•
Keep your elbow at 90 degrees.
•
Keep your knees at greater than 90 degrees, and
keep your heels firmly on the floor. Keep your arms
lower than your heart.
Introduction
{LD190,LD190G}Package Contents
Note
Please make sure the following items are included with your monitor.
If any items are missing, contact your dealer.
Contact a local dealer to buy optional items.
Unpacking
Monitor
Manuals
Quick Setup Guide
Warranty Card
User's Guide
(Not available in all locations)
(Not available in all locations)
Power Cord
USB Cable
Cables
D-Sub Cable
Others
Cleaning Cloth
Introduction
Note
Cleaning Cloth is only provided for highly polished black products as a product
feature.
Your Monitor
Initial Settings
Select the language using the up or down key.
The displayed content will disappear after 40 seconds.
Turn the Power button off and on. It will be displayed again.
It can be displayed up to three (3) times. Make sure to adjust the resolution of your PC before
reaching the maximum count.
Note
The resolution displayed on the screen is the optimal resolution for this product.
Adjust your PC resolution so that it is the same as the optimal resolution for this product.
Front
Note
Touch them lightly with your fingers to use them.
MENU button [MENU]
Opens the on-screen menu and exits from the menu. Also use to exit the
OSD menu or return to the previous menu.
Brightness button [ ]
Introduction
When OSD is not on the screen, push the button to adjust brightness.
AUTO button
When OSD is not on the screen, push the button for auto adjustment.
Adjust buttons [
]
These buttons allow you to adjust items in the menu.
Power button [
]
Use this button for turning the product on and off.
Note
See PowerSaver described in the manual for further information regarding
power saving functions. For energy conservation, turn your monitor OFF
when it is not needed or when leaving it unattended for long periods.
Rear
Note
The configuration at the back of the product may vary from product to product.
POWER port
Connect the power cord for your monitor to the POWER port on the back of
the product.
USB IN port
Connect the
cable.
of the monitor and the USB of the computer with the USB
RGB IN port
Connect the D-sub cable to the 15-pin, RGB IN port on the back of your monitor.
Kensington Lock
Introduction
The Kensington lock is a device used to physically fix the system when using
it in a public place. (The locking device has to be purchased separately.) For
using a locking device, contact where you purchase it.
Note
The location of the Kensington Lock may be different depending on its model.
Using the Anti-Theft Kensington Lock
1.
Insert the locking device into the Kensington slot on the Monitor
turn it in the locking direction
and
.
2.
Connect the Kensington Lock cable.
3.
Fix the Kensington Lock to a desk or a heavy stationary object.
Note
See Connecting Cables for further information regarding cable connections.
{LD220,LD220G}Package Contents
Note
Please make sure the following items are included with your monitor.
If any items are missing, contact your dealer.
Contact a local dealer to buy optional items.
Unpacking
Monitor
Manuals
Quick Setup Guide
Warranty Card
User's Guide
(Not available in all locations)
(Not available in all locations)
Introduction
Cables
D-Sub Cable
Power Cord
USB Cable
Others
Cleaning Cloth
Note
Cleaning Cloth is only provided for highly polished black products as a product
feature.
Your Monitor
Initial Settings
Select the language using the up or down key.
The displayed content will disappear after 40 seconds.
Turn the Power button off and on. It will be displayed again.
It can be displayed up to three (3) times. Make sure to adjust the resolution of your PC before
reaching the maximum count.
Note
The resolution displayed on the screen is the optimal resolution for this product.
Adjust your PC resolution so that it is the same as the optimal resolution for this product.
Introduction
Front
Note
Touch them lightly with your fingers to use them.
MENU button [MENU]
Opens the on-screen menu and exits from the menu. Also use to exit the
OSD menu or return to the previous menu.
Brightness button [ ]
When OSD is not on the screen, push the button to adjust brightness.
AUTO button
When OSD is not on the screen, push the button for auto adjustment.
Adjust buttons [
]
These buttons allow you to adjust items in the menu.
Power button [
]
Use this button for turning the product on and off.
Note
See PowerSaver described in the manual for further information regarding
power saving functions. For energy conservation, turn your monitor OFF
when it is not needed or when leaving it unattended for long periods.
Rear
Note
The configuration at the back of the product may vary from product to product.
Introduction
POWER port
Connect the power cord for your monitor to the POWER port on the back of
the product.
USB OUT port
DOWN(USB downstream port)
Connect the
USB cable.
DOWN port of the USB monitor and a USB device with the
UP(USB upstream port)
Connect the
UP port of the monitor and the USB port of the computer
with the USB cable.
USB IN port
Connect the
USB cable.
port of the monitor and the USB of the computer with the
RGB IN port
Connect the D-sub cable to the 15-pin, RGB IN port on the back of your monitor.
Kensington Lock
The Kensington lock is a device used to physically fix the system when using
it in a public place. (The locking device has to be purchased separately.) For
using a locking device, contact where you purchase it.
Note
The location of the Kensington Lock may be different depending on its model.
Introduction
Using the Anti-Theft Kensington Lock
1.
Insert the locking device into the Kensington slot on the Monitor
turn it in the locking direction
.
2.
Connect the Kensington Lock cable.
3.
Fix the Kensington Lock to a desk or a heavy stationary object.
Note
See Connecting Cables for further information regarding cable connections.
and
Connections
Monitor connection with D-SUB cable
Connect the power cord for your monitor to the power port on the back of the
monitor.
Plug the power cord for the monitor into a nearby outlet.
Use a connection appropriate for your computer.
Using the D-sub (Analog) connector on the video card.
•
Connect the signal cable to the 15-pin, D-sub port on the back of your monitor.
[RGB IN]
Connected to a Macintosh.
•
Connect the monitor to the Macintosh computer using the D-sub connection
cable.
Note
If the monitor and the computer are connected, you can turn them on and use them.
Use a general monitor in the following cases.
•
When using a single display
•
When playing a 3D game
•
When watching a BluRay or HD video
Note
For laptop, "LCD+CRT Dual View" mode must be selected first before the multi-monitor configuration.
Connections
Press the Fn + F4(
) key combination once.
Then the 'Easy Display Manager'screen appears in which you can select a display device.
) key while holding down the Fn key, the selected option
Whenever you press the F4(
is changed.
Monitor connection with USB cable
Note
The monitor can be operated with USB cable connection only. The monitor can be operated
with D-sub cable connection as well.
Installation Requirements
Installation Requirements
1.When using a common office or web document
- CPU : 1.6 Ghz Atom or Celeron
- RAM : 1 GB
2. When watching a movie in full screen mode
- CPU : 1.8Ghz Core2
- RAM : 1 GB
Supported OS (Operating - Windows XP Service Pack 2 or later
Systems)
- Windows 2000 Service Pack 4 or later
- Windows Vista
Note
•
To find out the PC operating system information, Right click 'My Computer' and choose
'Properties' and select 'General' tab.
•
Movie scenes may not be played continuously and smoothly due to the PC specifications
or movie player codec.
•
When using a notebook PC, set the battery mode to Maximum Performance mode to play
a movie at the best quality.
Use a USB monitor in the following cases.
•
When using more than one display
•
When using multiple monitors in Plug & Play mode
Connecting a USB Monitor
1.Connect the power cord (
) to your monitor as shown above.
2.Connect the USB cable (
) to monitor and PC as shown above.
3.More than 2 monitors connection with USB cable.
Connect the USB cable (
) to two different monitors as shown above.
Connections
(LD220/LD220G models only) Maximum of 4 monitors can be used at a same time with a
serial USB connection.
Maximum of 6 monitors can be used at a same time with a parallel USB connection.
When connecting serially
You can connect up to four (4) USB monitors serially.
When connecting in parallel
You can connect up to six (6) USB monitors in parallel.
When connecting external devices to the USB monitor, you can only connect up to four (4)
devices.
USB Monitor Driver Installation
Make sure to begin the installation after your PC has booted completely.
Note
If you turn off the monitor or remove the USB cable during installation, it may cause some
error to your PC and the installation will not be completed.
1.
Insert the installation CD into your PC CD-ROM drive. Click the USB Monitor Driver icon
and start installation.
Note
USB Monitor Driver Icon :
2.
Click "I Accept" button and installation will progress.
Connections
3.
connecting the monitor to PC with USB cable, the following message (as shown picture)
will appear on your PC window in a sequential manner.
4.
When installation is completed, a monitor icon is created in the system tray at the bottom
of window screen. The installed USB Monitor information is displayed as shown below.
5.
When the Driver installation is completed, please set the USB monitor to multi-monitor.
•
USB Driver online download
Please visit the Download Center (http://www.samsung.com) and download the USB
Monitor Driver by searching the model name.
•
Display settings after program installation
Applicable mode: Extend mode
Connections
Mode position: Right hand side of the Main Screen
Mode rotation: 0 °
Multi-monitor Configuration
Note
Both USB monitor (USB Cable connection) and general monitor (D-SUB connection) have
same multi-monitor configuration.
1.
Click 'Start >Control panel > Appearance and Themes >Display'.
2.
Select 'Settings' tab.
3.
Click second monitor icon and check 'Extend my windows desktop onto this monitor'.
Then click 'Apply' button shown as below.
4.
Click the 'Identify' button and check the given number for each monitor. Arrange the
monitor in order.
5.
Then click "OK" button.
Display Information Setup for USB Monitor
1.
When USB Monitor Driver installation is completed, a monitor icon is created in the system tray at the bottom of the window screen.
Connections
2.
Click the monitor icon to display a list of connected USB monitors.
e.g.,) The following figure shows when two USB monitors are connected. Select the
monitor for which you want to configure the display settings. You can configure the
"Screen Resolution" , "Color Quality" and "Screen Rotation" settings for your monitor.
Note
1.
Because this USB monitor is recognized as a USB device, the DOS screen that appears
for general monitors when a PC is booting up is not displayed.
- In order to view booting information (DOS), use D-SUB cable (Analog Signal) connection.
2.
3.
USB monitor is not compatible to any software that requires 3D hardware acceleration.
•
Real Player (Expansion mode is not supported.)
•
Most 3D games
•
Programs based on DirectX
It is recommended using the following settings to play a movie at the best quality.
•
Set the battery mode of your notebook PC to Maximum Performance mode.
•
If a movie is not played smoothly in full screen mode, use a lower screen resolution.
Depending on PC interface or incompatible codec packs, it can cause serious playback
issues, such as flickering or choppy video on the screen.
4.
If you connect more than one USB monitor, a blank screen will appear until PC recognizes the USB device. Screen will be displayed after PC recognizes the USB device.
(LD220/LD220G models only)
1.
I cannot turn on the monitor.
Q&A
•
2.
Connect the power cable again.
There is no image on the screen.
•
Unplug the power code and replug in.
•
Connect the USB cable again.
Connections
3.
•
Install the USB driver.
•
As USB port can be unstable, reboot your PC.
•
PC's USB port may be faulty. Please try to connect different port.
•
USB monitor may not work on USB 1.0.
•
Any input from mouse or keyboard will activate the display if it is under the power
saving mode.
I can't install USB Driver with the supplied CD.
•
4.
After installing USB Driver, The computer performance is slow.
•
5.
Download USB driver at Samsung Electronics website and install it.[ http://www.samsung.com ]
As USB Driver takes more memory than the use of general graphic card, computer
performance may be lower than before.
After booting the PC, screen order is changed.
•
Update your graphic card to the latest version.
Note
For graphic card driver, refer to graphic card manufacturer's home page.
6.
Monitor resolution is changed.
•
Please make a reference to [USB Monitor Installation guide]- 'Display Information
Setup for USB Monitor' for best resolution
[Best Resolution - LD190/LD190G: 1360X768, LD220/LD220G: 1920x1080]
7.
While playing high quality video file, choppy video can be seen repeatedly.
•
8.
When you watch high quality video file in full screen mode, it may play properly due
to limited USB bandwidth. It is strongly recommend to decrease the window size of
the movie player. Depending on PC interface or incompatible codec packs, it can
cause serious playback issues, such as flickering or choppy video on the screen.
I can use Clone mode, but can't set to extend mode.
•
Update your graphic card to the latest version.
Note
For graphic card driver, refer to graphic card manufacturer's home page.
9.
•
Right click 'Desktop' -'Property' - 'Settings' tab. Check 'Extend my windows desktop
onto this monitor'.
•
If graphic card does not support WDDM, Extend mode can not be used in windows
Vista. e.g.,) Some versions in Matrox Card.
How can I remove the ‘USB Monitor Installation Program’ completely?
•
Click ‘Add/Remove Programs’ in the ‘Control Panel’. A list of ‘Currently Installed Programs’ is displayed.
•
Select ‘Samsung UbiSync Monitor’ from the list and click ‘Remove’.
Connections
10. I disconnected or turned off my USB monitor but my PC still displays the old monitor
information in the Display Properties window.
•
Deactivated USB monitor is due to either the power is off or there is no USB connection. In order to remove this information, 'Samsung Ubisync Monitor' program
must be removed. This can be done by click 'Start' - 'Control Panel' - 'Add/Remove
Programs' - 'Samsung Ubisync Monitor' - 'Remove'. All the connected USB monitors
will not be able to use if the software program is removed. Installation software program must be installed again in ordr to use USB monitor.
11. The screen of USB monitor is frozen.
Check "Hardware Acceleration" on desktop property.
•
1.Click 'Start > Control Panel> Appearance and Themes> Display> Settings > Advanced'.
2.Select 'Troubleshoot' tab, when displayed. Set the ‘Hardware acceleration(H)’ value to ‘Full’.
12. Icons and photos are broken or jagged in Clone mode (USB monitor).
•
This occurs because Windows does not send the screen updating information to
Clone mode if Extended mode is active on a single PC. We recommend using the
monitor in Extend mode.
Connecting USB{LD220/LD220G}
Note
You can use a USB device such as a mouse, keyboard, Memory Stick, or external hard disk
drive by connecting them to the
the PC.
The
DOWN port of the monitor without connecting them to
USB port of the monitor supports High-Speed Certified USB 2.0.
Data Rate
High speed
Full speed
Low speed
480 Mbps
12 Mbps
1.5 Mbps
2.5 W
2.5 W
(Max., each port)
(Max., each port)
Power Consump- 2.5 W
tion
(Max., each port)
Connections
1.
Connect the
cable.
UP port of the monitor and the USB port of the computer with the USB
Note
To use
DOWN port, you have to connect the UP (Upstream Cable) to the PC.
Make sure to use the USB cable supplied with this monitor to connect the monitor's
UP port and your computer's USB port.
2.
Connect the
3.
The use procedures are as the same as those for using an external device connecting
to the PC.
DOWN port of the USB monitor and a USB device with the USB cable.
•
You can connect and use a keyboard and mouse.
•
You can play a file from a media device.
(Examples of media devices: MP3, digital camera, etc.)
•
You can run, move, copy or delete the files on the storage device.
(Examples of storage devices: external memory, memory card, memory reader,
HDD-type MP3 player, etc.)
•
You can use other USB devices that can be connected to a computer.
Note
DOWN port of the monitor, connect the device
When connecting a device to the
using a cable appropriate to the device.
(For the purchase of the cable and external devices, ask the service center of the corresponding product.)
The company is not liable for problems or damages to an external device caused by
using an unauthorized cable for the connection.
Some products do not follow the USB standard, and it may cause a malfunction of the
device.
If the device malfunctions even if it is connected to the computer, contact the service
center of the device/computer.
Connections
Using the Stand
Folding the base
Note
You can tilt the monitor backwards at an angle of 10 °~ 30 ° (±5°) .
Using the Software
Monitor Driver
Note
When prompted by the operating system for the monitor driver, insert the CDROM included with this monitor. Driver installation is slightly different from one
operating system to another. Follow the directions appropriate for the operating system you have.
Prepare a blank disk and download the driver program file at the Internet web
site shown here.
Internet web site :
http://www.samsung.com/ (Worldwide)
Installing the Monitor Driver (Automatic)
1.
Insert CD into the CD-ROM drive.
2.
Click "Windows".
3.
Choose your monitor model in the model list, then click the "OK" button.
4.
If you can see following message window, then click the "Continue Anyway" button. Then
click "OK" button (Microsoft® Windows® XP/2000 Operating System).
Using the Software
Note
This monitor driver is under certifying MS logo, and this installation doesn't damage your
system.
The certified driver will be posted on Samsung Monitor homepage.
http://www.samsung.com/
Installing the Monitor Driver (Manual)
Microsoft® Windows Vista™‚ Operating System
1.
Insert your Manual CD into your CD-ROM drive.
2.
Click
(Start) and "Control Panel". Then, double-click on "Appearance and Personalization".
3.
Click "Personalization" and then "Display Settings".
4.
Click "Advanced Settings...".
5.
Click "Properties" in the "Monitor" tab. If the "Properties" button is deactivated, it means
the configuration for your monitor is completed. The monitor can be used as is.
Using the Software
If the message "Windows needs..." is displayed, as shown in the figure below, click
"Continue".
Note
This monitor driver is under certifying MS logo, and this installation doesn't damage your
system.
The certified driver will be posted on Samsung Monitor homepage.
6.
Click "Update Driver..." in the "Driver" tab.
7.
Check the "Browse my computer for driver software" checkbox and click "Let me pick
from a list of device drivers on my computer".
8.
Click "Have Disk...” and select the folder (for example, D:\Drive) where the driver setup
file is located, and click "OK".
Using the Software
9.
Select the model that matches your monitor from the list of monitor models on the screen,
and click "Next".
10. Click "Close" → "Close" → "OK" → "OK" on the following screens displayed in sequence.
Microsoft® Windows® XP Operating System
Using the Software
1.
Insert CD into the CD-ROM drive.
2.
Click "Start" → "Control Panel" then click the "Appearance and Themes" icon.
3.
Click "Display" icon and choose the "Settings" tab then click "Advanced...".
4.
Click the "Properties" button on the "Monitor" tab and select "Driver" tab.
5.
Click "Update Driver..." and select "Install from a list or..." then click "Next" button.
6.
Select "Don't search, I will..." then click "Next" and then click "Have disk".
Using the Software
7.
Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in
the model list and click the "Next" button.
8.
If you can see following message window, then click the "Continue Anyway" button. Then
click "OK" button.
Note
This monitor driver is under certifying MS logo, and this installation doesn't damage your
system.
The certified driver will be posted on Samsung Monitor homepage.
http://www.samsung.com/
9.
Click the "Close" button then click "OK" button continually.
Using the Software
10. Monitor driver installation is completed.
Microsoft® Windows® 2000 Operating System
When you can see "Digital Signature Not Found" on your monitor, follow these steps.
1.
Choose "OK" button on the "Insert disk" window.
2.
Click the "Browse" button on the "File Needed" window.
3.
Choose A:(D:\Driver) then click the "Open" button and then click "OK" button.
How to install
1.
Click "Start", "Setting", "Control Panel".
2.
Double click the "Display" icon.
3.
Select the "Settings" tab and click "Advanced Properties" button.
4.
Choose "Monitor".
Case1 : If the "Properties" button is inactive, it means your monitor is properly configured.
Please stop installation
Case2 : If the "Properties" button is active, click the "Properties" button then follow next
steps continually.
5.
Click "Driver" and then click on "Update Driver..." then click on the "Next" button.
6.
Choose "Display a list of the known drivers for this device so that I can choose a specific
driver" then click "Next" and then click "Have disk".
7.
Click the "Browse" button then choose A:(D:\Driver).
8.
Click the "Open" button, then click "OK" button.
9.
Choose your monitor model and click the "Next" button then click "Next" button.
10. Click the "Finish" button then the "Close" button.
If you can see the "Digital Signature Not Found" window then click the "Yes" button. And
click the "Finish" button then the "Close" button.
Microsoft® Windows® Millennium Operating System
1.
Click "Start", "Setting", "Control Panel".
2.
Double click the "Display" icon.
3.
Select the "Settings" tab and click "Advanced Properties" button.
Using the Software
4.
Select the "Monitor" tab.
5.
Click the "Change" button in the "Monitor Type" area.
6.
Choose "Specify the location of the driver".
7.
Choose "Display a list of all the driver in a specific location..." then click "Next" button.
8.
Click the "Have Disk" button.
9.
Specify A:\(D:\driver) then click "OK" button.
10. Select "Show all devices" and choose the monitor that corresponds to the one you connected to your computer and click "OK".
11. Continue choosing "Close" button and "OK" button until you close the Display Properties
dialogue box.
Microsoft® Windows® NT Operating System
1.
Click "Start", "Settings", "Control Panel", and then double-click "Display" icon.
2.
In Display Registration Information window, click Settings Tab and then click "All Display
Modes".
3.
Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency)
and then click "OK".
4.
Click "Apply" button if you see the screen working normally after clicking "Test". If the
screen is not normal, change to a different mode (lower mode of resolution, colors or
frequency).
Note
If there is no Mode at All Display Modes, select the level of resolution and vertical frequency
by referring to the Preset Timing Modes in the user guide.
Linux Operating System
To execute X-Window, you need to make the X86Config file, which is a type of system setting
file.
1.
Press "Enter" at the first and the second screen after executing the X86Config file.
2.
The third screen is for setting your mouse.
3.
Set a mouse for your computer.
4.
The next screen is for selecting a keyboard.
5.
Set a Keyboard for your computer.
6.
The next screen is for setting your monitor.
7.
First of all, set a horizontal frequency for your monitor. (You can enter the frequency
directly.)
8.
Set a vertical frequency for your monitor. (You can enter the frequency directly.)
9.
Enter the model name of your monitor. This information will not affect the actual execution
of X-Window.
Using the Software
10. You have finished setting up your monitor. Execute X-Window after setting other requested hardware.
Adjusting the Monitor
Direct Functions
Note
•
The monitor LED displays for 10 seconds
•
Press the MENU button four times continuously to exit OSD
AUTO(Available in Analog mode only)
When no OSD is displayed,press” ” button to perform the AUTO function, the auto adjustment
screen appears as shown in the animated screen on the center.
Auto adjustment allows the monitor to self-adjust to the incoming Analog signal.
If auto adjustment does not work properly, press “ “ button again to adjust picture with
more accuracy.
If you change resolution in the control panel, auto function will be executed automatically.
Brightness
When no OSD is displayed,press” ” button to perform the Brightness function.
Toggle the Source
In power saving mode, the power LED is blinking all the time, or in the Checksignal
menu,press” / ” buttons to perform the Source function.
OSD Function
Brightness
MagicBright Custom
NotePC
Source
Analog
USB
Image Size
Auto
Wide
Internet
Movie
Dynamic
Contrast
Adjusting the Monitor
Language
Exit
Brightness
(Not available in MagicBright mode of Dynamic Contrast.)
You can use the on-screen menus to change the brightness according to personal preference.
MENU → MENU →
MENU
,
→
MagicBright
MagicBright is a new feature providing optimum viewing environment depending on the contents of the image you are watching. Currently five different modes are available: Custom,
NotePC, Internet, Movie and Dynamic Contrast. Each mode has its own pre-configured
brightness value.
MENU → ,
→ MENU
•
→ MENU→
,
Custom
Although the values are carefully chosen by our engineers, the pre-configured values may
not be comfortable to your eyes depending on your taste.
If this is the case, adjust the brightness by using the OSD menu.
•
NotePc
Used for connecting to a notebook screen.
•
Internet
For working with a mixture of images such as texts and graphics.
•
Movie
Adjusting the Monitor
For watching motion pictures such as a DVD or Video CD.
•
Dynamic Contrast
Dynamic Contrast automatically detects distribution of inputted visual signal and adjusts
to create optimum contrast.
Source
Choose the video signal between Analog and USB.
MENU → ,
→ MENU
→ MENU→
,
Image Size
You can change the size of the screen displayed on your monitor.
Note
•
Signals not available in the
standard mode table are
not supported.
•
If the wide screen which is
the optimal resolution for
the monitor is set on your
PC, this function is not performed.
MENU → ,
→ MENU
•
→ MENU→
,
•
Auto
Wide
•
Auto - The screen is displayed in accordance with the screen aspect ratio of the input
signals.
•
Wide - A full screen is displayed regardless of the screen aspect ratio of the input signals.
Language
You can choose one of nine languages.
Adjusting the Monitor
Note
The language chosen affects
only the language of the OSD.
It has no effect on any software
running on the computer.
MENU → ,
→ MENU
→ MENU→
MENU →
→ MENU
Exit
Perform this function to close OSD.
,
,
Troubleshooting
Self-Test Feature Check
Note
Your monitor provides a self test feature that allows you to check whether your monitor is
functioning properly.
Self-Test Feature Check
1.
Turn off both your computer and the monitor.
2.
Unplug the video cable from the back of the computer.
3.
Turn on the monitor.
If the monitor is functioning properly, you will see a box in the illustration below.
This box appears during normal operation if the video cable becomes disconnected or
damaged.
4.
Turn off your monitor and reconnect the video cable; then turn on both your computer
and the monitor.
If your monitor screen remains blank after using the previous procedure, check your video
controller and computer system; your monitor is functioning properly.
Warning Messages
If there is something wrong with the input signal, a message appears on the screen or the
screen goes blank although the power indicator LED is still on. The message may indicate
that the monitor is out of scan range or that you need to check the signal cable.
Environment
The location and the position of the monitor may influence the quality and other features of
the monitor.
If there are any sub woofer speakers near the monitor, unplug and relocate the woofer to
another room.
Remove all electronic devices such as radios, fans, clocks and telephones that are within 3
feet (one meter) of the monitor.
Troubleshooting
Useful Tips
A monitor recreates visual signals received from the computer. Therefore, if there is a problem
with the computer or the video card, this can cause the monitor to become blank, have poor
coloring, become noisy, and video mode not supported, etc. In this case, first check the source
of the problem, and then contact the Service Center or your dealer.
Judging the monitor's working condition
If there is no image on the screen or a "Not Optimum Mode", "Recommended Mode 1360 x
768(1920 x 1080) 60 Hz" message comes up, disconnect the cable from the computer while
the monitor is still powered on.
If there is a message coming up on the screen or if the screen goes white, this means the
monitor is in working condition.
In this case, check the computer for trouble.
Check List
Note
Before calling for assistance, check the information in this section to see if you can remedy
any problems yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer.
No images on the screen. I cannot turn on the monitor.
Q:
Is the power cord connected properly?
A:
Check the power cord connection and supply.
Q:
Can you see "Check Signal Cable" on the screen?
A:
(Connected using the D-sub cable)
Check the signal cable connection.
Q:
If the power is on, reboot the computer to see the initial screen (the login screen), which
can be seen.
A:
If the initial screen (the login screen) appears, boot the computer in the applicable mode
(the safe mode for Windows ME/XP/2000) and then change the frequency of the video
card.
(Refer to the Preset Timing Modes)
If the initial screen (the login screen) does not appear, contact the Service Center or
your dealer.
Q:
Can you see "Not Optimum Mode", "Recommended Mode 1360 x 768(1920 x 1080)
60 Hz" on the screen?
A:
You can see this message when the signal from the video card exceeds the maximum
resolution and frequency that the monitor can handle properly.
A:
Adjust the maximum resolution and frequency that the monitor can handle properly.
A:
If the display exceeds SXGA or 75 Hz, a "Not Optimum Mode", "Recommended
Mode 1360 x 768(1920 x 1080) 60 Hz" message is displayed. If the display exceeds
85 Hz, the display will work properly but the "Not Optimum Mode", "Recommended
Troubleshooting
Mode 1360 x 768(1920 x 1080) 60 Hz" message appears for one minute and then
disappears.
Please change to the recommended mode during this one-minute period.
(The message is displayed again if the system is rebooted.)
Q:
There is no image on the screen. Is the power indicator on the monitor blinking at 1
second intervals?
A:
The monitor is in PowerSaver mode.
A:
Press a key on the keyboard to activate the monitor and restore the image on the screen.
A:
If a(n) (error) message is displayed on the screen when the monitor is properly connected, please check if the monitor is set to Analog/USB. Press the MENU button, when
the menu appears, enter the Source option to toggle the Source. When no OSD is
displayed, press” / to toggle the Source.
The screen shows strange colors or just black and white.
Q:
Is the screen displaying only one color as if looking at the screen through a cellophane
paper?
A:
Check the signal cable connection.
A:
Make sure the video card is fully inserted in its slot.
Q:
Have the screen colors become strange after running a program or due to a crash
between applications?
A:
Reboot the computer.
Q:
Has the video card been set properly?
A:
Set the video card by referring to the video card manual.
The screen suddenly has become unbalanced.
Q:
Have you adjusted the resolution or frequency to the monitor?
A:
Adjust the resolution and frequency at the video card.
(Refer to the Preset Timing Modes).
Q:
The screen can be unbalanced due to the cycle of the video card signals.
The screen is out of focus or OSD cannot be adjusted.
Q:
Have you adjusted the resolution or frequency on the monitor?
A:
Adjust the resolution and frequency of the video card.
(Refer to the Preset Timing Modes).
LED is blinking but no images on the screen.
Q:
Is the frequency properly adjusted when checking the Display Timing on the menu?
A:
Adjust the frequency properly by referring to the video card manual and the Preset
Timing Modes.
Troubleshooting
(The maximum frequency per resolution may differ from product to product.)
There are only 16 colors shown on the screen. The screen colors have changed after
changing the video card.
Q:
Have the Windows colors been set properly?
A:
Windows XP :
Set the resolution at the Control Panel → Appearance and Themes → Display → Settings.
A:
Windows ME/2000 :
Set the resolution at the Control Panel → Display → Settings.
Q:
Has the video card been set properly?
A:
Set the video card by referring to the video card manual.
There is a message that reads "Unrecognized monitor, Plug & Play (VESA DDC) monitor found".
Q:
Have you installed the monitor driver?
A:
Install the monitor driver according to the Monitor Driver.
Q:
See the video card manual to see if the Plug & Play (VESA DDC) function can be
supported.
A:
Install the monitor driver according to the Monitor Driver.
Check the following items if there is trouble with the monitor.
Check if the power cord and the video cables are properly connected to the computer.
Check if the computer beeps more than 3 times when booting.
(If it does, request an a service for the main board of the computer.)
If you installed a new video card or if you assembled the PC, check if the installed the adapter
(video) driver and the monitor driver.
Check if the scanning ratio of the video screen is set to between 50 Hz ~ 75 Hz(LD190/
LD190G)/56 Hz ~ 61 Hz(LD220/LD220G).
(Do not exceed 75 Hz(LD190/LD190G) /61 Hz(LD220/LD220G) when using the maximum
resolution.)
If you have problems in installing the adapter (video) driver, boot the computer in Safe Mode,
remove the Display Adapter in the "Control Panel → System → Device Administrator" and
then reboot the computer to reinstall the adapter (video) driver.
Note
If problems repeatedly occur, contact an authorized service center.
Q&A
Q:
How can I change the frequency?
Troubleshooting
A:
The frequency can be changed by reconfiguring the video card.
A:
Note that video card support can vary, depending on the version of the driver used.
(Refer to the computer or the video card manual for details.)
Q:
How can I adjusts the resolution?
A:
Windows XP:
Set the resolution in the Control Panel → Appearance and Themes → Display → Settings.
A:
Windows ME/2000:
Set the resolution in the Control Panel → Display → Settings.
* Contact the video card manufacturer for details.
Q:
How can I set the Power Saving function?
A:
Windows XP:
Set the resolution in the Control Panel → Appearance and Themes → Display → Screen
Saver.
Set the function in the BIOS-SETUP of the computer. (Refer to the Windows / Computer
Manual).
A:
Windows ME/2000:
Set the resolution at the Control Panel → Display → Screen Saver.
Set the function in the BIOS-SETUP of the computer. (Refer to the Windows / Computer
Manual).
Q:
How can I clean the outer case/LCD Panel?
A:
Disconnect the power cord and then clean the monitor with a soft cloth, using either a
cleaning solution or plain water.
Do not leave any detergent or scratches on the case. Do not let any water enter the
monitor.
Q:
How I can clone or extend screen mode?
A:
Open the “Display Properties” window and select the “Settings” tab,
- For more information on how to configure the settings, click here.
Note
Before calling for assistance, check the information in this section to see if you can remedy
any problems yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer.
Specifications
General
General
Model Name
SyncMaster LD190
LCD Panel
Size
18.5 inch (47 cm)
Display area
409.8 mm (H) x 230.4 mm (V)
Pixel Pitch
0.3 mm (H) x 0.3 mm (V)
Synchronization
Horizontal
30 ~ 81 kHz
Vertical
50 ~ 75 Hz
Display Color
16.7 M
Resolution
Optimum resolution
1360 x 768@60 Hz
Maximum resolution 1360 x 768@60 Hz
Input Signal, Terminated
RGB Analog, USB
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
89 MHz (Analog, USB)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
USB Interface connector,Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
450.2 x 295.8 x 72.0 mm (17.7 x 11.6 x 2.8 inch) (With Stand) / 4.7 kg(10.4 lbs)
Environmental considerations
Operating
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Humidity : 10 % ~ 80 %, non-condensing
Storage
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Specifications
Environmental considerations
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating
conditions and monitor settings. In most cases, the monitor installation will proceed
automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with
precision of 1ppm (one millionth) above are used for this product. But the pixels of
RED, GREEN, BLUE and WHITE color appear to be bright sometimes or some
black pixels may be seen. This is not from bad quality and you can use it without
any problems.
For example, the number of TFT-LCD sub pixels contained in this product are
3,133,440.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use
and can be used in all areas including common residential areas. (Class B equipment emits
less electromagnetic waves than Class A equipment.)
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves
energy by switching your monitor to low-power mode when it has not been used for a certain
amount of time. The monitor automatically returns to normal operation when you press a key
on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or
when leaving it unattended for long periods. The PowerSaver system operates with a VESA
DPM compliant video card installed in your computer. Use the software utility installed on
your computer to set up this feature.
State
Normal Operation
Power saving
mode
Power off (Power button)
EPA/ENERGY 2000
Power Indicator
On
Blinking
Off
Power Consumption
20 watts
Analog: Less than
1 watt
Less than 1 watts
USB: Less than 1
watt
This monitor is EPA ENERGY STAR® compliant and
ENERGY 2000 compliant when used with a computer
equipped with VESA DPM functionality.
As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets the ENERGY STAR®
guidelines for energy efficiency.
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes,
the screen will be adjusted automatically. However, if the signal differs, the screen may go
blank while the power LED is on. Refer to the video card manual and adjusts the screen as
follows.
Display Mode
Horizontal
Frequency
(kHz)
Vertical Fre- Pixel Clock
quency (Hz)
(MHz)
Sync Polarity
(H/V)
IBM, 640 x 350
31.469
70.086
25.175
+/-
IBM, 640 x 480
31.469
59.940
25.175
-/-
IBM, 720 x 400
31.469
70.087
28.322
-/+
MAC, 640 x 480
35.000
66.667
30.240
-/-
MAC, 832 x 624
49.726
74.551
57.284
-/-
VESA, 640 x 480
37.861
72.809
31.500
-/-
VESA, 640 x 480
37.500
75.000
31.500
-/-
VESA, 800 x 600
35.156
56.250
36.000
+/+
VESA, 800 x 600
37.879
60.317
40.000
+/+
VESA, 800 x 600
48.077
72.188
50.000
+/+
VESA, 800 x 600
46.875
75.000
49.500
+/+
VESA, 1024 x 768
48.363
60.004
65.000
-/-
VESA, 1024 x 768
56.476
70.069
75.000
-/-
VESA, 1024 x 768
60.023
75.029
78.750
+/+
VESA, 1360 x 768
47.712
60.015
85.500
+/+
Horizontal Frequency
The time to scan one line connecting the right edge
to the left edge of the screen horizontally is called the
Horizontal Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency.
Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the
same image many times per second to display an
image to the user. The frequency of this repetition is
called the Vertical Frequency or Refresh Rate. Unit:
Hz
General
General
Model Name
SyncMaster LD190G
LCD Panel
Size
18.5 inch (47 cm)
Display area
409.8 mm (H) x 230.4 mm (V)
Pixel Pitch
0.3 mm (H) x 0.3 mm (V)
Specifications
Synchronization
Horizontal
30 ~ 81 kHz
Vertical
50 ~ 75 Hz
Display Color
16.7 M
Resolution
Optimum resolution
1360 x 768@60 Hz
Maximum resolution 1360 x 768@60 Hz
Input Signal, Terminated
RGB Analog, USB
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
89 MHz (Analog, USB)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
USB Interface connector,Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
450.2 x 295.8 x 72.0 mm (17.7 x 11.6 x 2.8 inch) (With Stand) / 4.7 kg(10.4 lbs)
Environmental considerations
Operating
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Humidity : 10 % ~ 80 %, non-condensing
Storage
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating
conditions and monitor settings. In most cases, the monitor installation will proceed
automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with
precision of 1ppm (one millionth) above are used for this product. But the pixels of
RED, GREEN, BLUE and WHITE color appear to be bright sometimes or some
Specifications
Dot Acceptable
black pixels may be seen. This is not from bad quality and you can use it without
any problems.
For example, the number of TFT-LCD sub pixels contained in this product are
3,133,440.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use
and can be used in all areas including common residential areas. (Class B equipment emits
less electromagnetic waves than Class A equipment.)
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves
energy by switching your monitor to low-power mode when it has not been used for a certain
amount of time. The monitor automatically returns to normal operation when you press a key
on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or
when leaving it unattended for long periods. The PowerSaver system operates with a VESA
DPM compliant video card installed in your computer. Use the software utility installed on
your computer to set up this feature.
State
Normal Operation
Power saving
mode
Power off (Power button)
EPA/ENERGY 2000
Power Indicator
On
Blinking
Off
Power Consumption
20 watts
Analog: Less than
1 watt
Less than 1 watts
USB: Less than 1
watt
This monitor is EPA ENERGY STAR® compliant and
ENERGY 2000 compliant when used with a computer
equipped with VESA DPM functionality.
As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets the ENERGY STAR®
guidelines for energy efficiency.
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes,
the screen will be adjusted automatically. However, if the signal differs, the screen may go
blank while the power LED is on. Refer to the video card manual and adjusts the screen as
follows.
Display Mode
Horizontal
Frequency
(kHz)
Vertical Fre- Pixel Clock
quency (Hz)
(MHz)
Sync Polarity
(H/V)
IBM, 640 x 350
31.469
70.086
25.175
+/-
IBM, 640 x 480
31.469
59.940
25.175
-/-
Specifications
Display Mode
Horizontal
Frequency
(kHz)
Vertical Fre- Pixel Clock
quency (Hz)
(MHz)
Sync Polarity
(H/V)
IBM, 720 x 400
31.469
70.087
28.322
-/+
MAC, 640 x 480
35.000
66.667
30.240
-/-
MAC, 832 x 624
49.726
74.551
57.284
-/-
VESA, 640 x 480
37.861
72.809
31.500
-/-
VESA, 640 x 480
37.500
75.000
31.500
-/-
VESA, 800 x 600
35.156
56.250
36.000
+/+
VESA, 800 x 600
37.879
60.317
40.000
+/+
VESA, 800 x 600
48.077
72.188
50.000
+/+
VESA, 800 x 600
46.875
75.000
49.500
+/+
VESA, 1024 x 768
48.363
60.004
65.000
-/-
VESA, 1024 x 768
56.476
70.069
75.000
-/-
VESA, 1024 x 768
60.023
75.029
78.750
+/+
VESA, 1360 x 768
47.712
60.015
85.500
+/+
Horizontal Frequency
The time to scan one line connecting the right edge
to the left edge of the screen horizontally is called the
Horizontal Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency.
Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the
same image many times per second to display an
image to the user. The frequency of this repetition is
called the Vertical Frequency or Refresh Rate. Unit:
Hz
General
General
Model Name
SyncMaster LD220
LCD Panel
Size
21.5 inch (54 cm)
Display area
476.64 mm (H) x 268.11 mm (V)
Pixel Pitch
0.248 mm (H) x 0.248 mm (V)
Synchronization
Horizontal
30 ~ 75 kHz
Vertical
56 ~ 61 Hz
Display Color
16.7 M
Specifications
Resolution
Optimum resolution
1920 x 1080@60 Hz
Maximum resolution 1920 x 1080@60 Hz
Input Signal, Terminated
RGB Analog, USB
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
164 MHz (Analog, USB)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
USB Interface connector,Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
594.0 x 405.0 x 123.0 mm (23.4 x 15.9 x 4.8 inch) (With Stand) / 5.7 kg(12.6 lbs)
Environmental considerations
Operating
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Humidity : 10 % ~ 80 %, non-condensing
Storage
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating
conditions and monitor settings. In most cases, the monitor installation will proceed
automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with
precision of 1ppm (one millionth) above are used for this product. But the pixels of
RED, GREEN, BLUE and WHITE color appear to be bright sometimes or some
black pixels may be seen. This is not from bad quality and you can use it without
any problems.
For example, the number of TFT-LCD sub pixels contained in this product are
6,220,800.
Note
Design and specifications are subject to change without prior notice.
Specifications
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use
and can be used in all areas including common residential areas. (Class B equipment emits
less electromagnetic waves than Class A equipment.)
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves
energy by switching your monitor to low-power mode when it has not been used for a certain
amount of time. The monitor automatically returns to normal operation when you press a key
on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or
when leaving it unattended for long periods. The PowerSaver system operates with a VESA
DPM compliant video card installed in your computer. Use the software utility installed on
your computer to set up this feature.
State
Normal Operation
Power saving
mode
Power off (Power button)
EPA/ENERGY 2000
Power Indicator
On
Blinking
Off
Power Consumption
40 watts
Analog: Less than
1.2 watt
Less than 1.2 watts
USB: Less than
1.2 watt
This monitor is EPA ENERGY STAR® compliant and
ENERGY 2000 compliant when used with a computer
equipped with VESA DPM functionality.
As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets the ENERGY STAR®
guidelines for energy efficiency.
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes,
the screen will be adjusted automatically. However, if the signal differs, the screen may go
blank while the power LED is on. Refer to the video card manual and adjusts the screen as
follows.
Display Mode
Horizontal
Frequency
(kHz)
Vertical Fre- Pixel Clock
quency (Hz)
(MHz)
Sync Polarity
(H/V)
VESA, 640 x 480
31.469
59.940
25.175
-/-
VESA, 800 x 600
35.156
56.250
36.000
+/+
VESA, 800 x 600
37.879
60.317
40.000
+/+
VESA, 1024 x 768
48.363
60.004
65.000
-/-
VESA, 1280 X 800
49.702
59.810
83.500
-/+
VESA, 1280 X 960
60.000
60.000
108.000
+/+
VESA, 1280 X 1024
63.981
60.020
108.000
+/+
VESA, 1440 X 900
55.935
59.887
106.500
-/+
VESA, 1600 X 1200
75.000
60.000
162.000
+/+
VESA, 1680 X 1050
65.290
59.954
146.250
-/+
Specifications
Display Mode
Horizontal
Frequency
(kHz)
VESA, 1920 X 1080
66.587
Vertical Fre- Pixel Clock
quency (Hz)
(MHz)
59.934
138.500
Sync Polarity
(H/V)
+/-
Horizontal Frequency
The time to scan one line connecting the right edge
to the left edge of the screen horizontally is called the
Horizontal Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency.
Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the
same image many times per second to display an
image to the user. The frequency of this repetition is
called the Vertical Frequency or Refresh Rate. Unit:
Hz
General
General
Model Name
SyncMaster LD220G
LCD Panel
Size
21.5 inch (54 cm)
Display area
476.64 mm (H) x 268.11 mm (V)
Pixel Pitch
0.248 mm (H) x 0.248 mm (V)
Synchronization
Horizontal
30 ~ 75 kHz
Vertical
56 ~ 61 Hz
Display Color
16.7 M
Resolution
Optimum resolution
1920 x 1080@60 Hz
Maximum resolution 1920 x 1080@60 Hz
Input Signal, Terminated
RGB Analog, USB
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
164 MHz (Analog, USB)
Specifications
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
USB Interface connector,Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
594.0 x 405.0 x 123.0 mm (23.4 x 15.9 x 4.8 inch) (With Stand) / 5.7 kg(12.6 lbs)
Environmental considerations
Operating
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Humidity : 10 % ~ 80 %, non-condensing
Storage
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating
conditions and monitor settings. In most cases, the monitor installation will proceed
automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with
precision of 1ppm (one millionth) above are used for this product. But the pixels of
RED, GREEN, BLUE and WHITE color appear to be bright sometimes or some
black pixels may be seen. This is not from bad quality and you can use it without
any problems.
For example, the number of TFT-LCD sub pixels contained in this product are
6,220,800.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use
and can be used in all areas including common residential areas. (Class B equipment emits
less electromagnetic waves than Class A equipment.)
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves
energy by switching your monitor to low-power mode when it has not been used for a certain
amount of time. The monitor automatically returns to normal operation when you press a key
on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or
when leaving it unattended for long periods. The PowerSaver system operates with a VESA
DPM compliant video card installed in your computer. Use the software utility installed on
your computer to set up this feature.
Specifications
State
Normal Operation
Power saving
mode
Power off (Power button)
EPA/ENERGY 2000
Power Indicator
On
Blinking
Off
Power Consumption
40 watts
Analog: Less than
1.2 watt
Less than 1.2 watts
USB: Less than
1.2 watt
This monitor is EPA ENERGY STAR® compliant and
ENERGY 2000 compliant when used with a computer
equipped with VESA DPM functionality.
As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets the ENERGY STAR®
guidelines for energy efficiency.
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes,
the screen will be adjusted automatically. However, if the signal differs, the screen may go
blank while the power LED is on. Refer to the video card manual and adjusts the screen as
follows.
Display Mode
Horizontal
Frequency
(kHz)
Vertical Fre- Pixel Clock
quency (Hz)
(MHz)
Sync Polarity
(H/V)
VESA, 640 x 480
31.469
59.940
25.175
-/-
VESA, 800 x 600
35.156
56.250
36.000
+/+
VESA, 800 x 600
37.879
60.317
40.000
+/+
VESA, 1024 x 768
48.363
60.004
65.000
-/-
VESA, 1280 X 800
49.702
59.810
83.500
-/+
VESA, 1280 X 960
60.000
60.000
108.000
+/+
VESA, 1280 X 1024
63.981
60.020
108.000
+/+
VESA, 1440 X 900
55.935
59.887
106.500
-/+
VESA, 1600 X 1200
75.000
60.000
162.000
+/+
VESA, 1680 X 1050
65.290
59.954
146.250
-/+
VESA, 1920 X 1080
66.587
59.934
138.500
+/-
Horizontal Frequency
The time to scan one line connecting the right edge
to the left edge of the screen horizontally is called the
Horizontal Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency.
Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the
same image many times per second to display an
image to the user. The frequency of this repetition is
called the Vertical Frequency or Refresh Rate. Unit:
Hz
Information
For Better Display
Adjust the computer resolution and screen injection rate (refresh rate) on the
computer as described below to enjoy the best picture quality. You can have an
uneven picture quality on screen if the best picture quality is not provided for TFTLCD.
•
Resolution: 1360 x 768(1920 x 1080)
•
Vertical frequency (refresh rate): 60 Hz
TFT-LCD panels manufactured by using advanced semiconductor technology
with a precision of 1ppm (one millionth) and above is used for this product. But the
pixels of RED, GREEN, BLUE and WHITE color seem to be bright sometimes or
some of black pixels could be seen. This is not from bad quality and you can use
it without any problems.
•
For example, the number of TFT-LCD sub pixels contained in this product are
3,133,440(6,220,800).
When cleaning the monitor and the panel outside, please apply the recommended small amount of cleaner by using a soft cloth to polish. Do not force the
LCD area but rub softly.
If excessive force is applied, you may stain it.
If you are not satisfied with the picture quality, you can get better quality of
picture by performing the "Auto Adjustment function" in display screen that is appeared as window termination button is pressed.
When viewing a fixed screen for an extended period of time, a residual image
or blurriness may appear.
Change the mode to energy save or set a screensaver to move the picture when
you need to be away from the monitor for an extended period of time.
PRODUCT INFORMATION (Image Retention Free)
LCD Monitors and TVs may have image retention when switching from one image to another
especially after displaying a stationary image for a long time.
This guide is to demonstrate correct usage of LCD products in order to protect them from
Image retention.
Warranty
Warranty does not cover any damage caused by image retention.
Burn-in is not covered by the warranty.
What is Image retention ?
During normal operation of a LCD panel, pixel image retention doesn't occur. However, if the same image is displayed for a long time, a slight difference in electric
charge accumulates between the two electrodes which encase the liquid crystal.
This may cause the liquid crystal to build up in a certain areas of the display. Thus,
Information
the previous image is retained when switching to a new video image. All display
products, including LCD, are subject to image retention. This is not a product defect.
Please follow the suggestions below to protect your LCD from image retention.
Power Off, Screen Saver, or Power Save Mode
Ex)
•
•
Turn the power off when using a stationary pattern.
•
Turn the power off for 4 hours after 20 hours in use
•
Turn the power off for 2 hours after 12 hours in use
Use a Screen saver if possible
•
•
Screen saver in one color or a moving image is recommended.
Set the Monitor to power off with the PC Display Properties Power Scheme.
Suggestions for specific applications
Ex) Airports, Transit Stations, Stock Markets, Banks, and Controlling Systems We
recommend that you follow set up of your display system program as below:
Display Information together with Logo or Moving image cycle.
Ex) Cycle : Display Information for 1 hour followed by a Display Logo or moving
image for 1 minute.
Change the Color Information periodically (Use 2 different colors).
Ex) Rotate the Color Information with 2 colors every 30 minutes.
Avoid using a combination of characters and background color with large difference
in luminance.
Avoid using Grey colors, which can cause Image retention easily.
•
Avoid: Colors with big difference in luminance (Black & White, Grey)
Ex)
•
Recommended settings: Bright colors with little difference in luminance
Information
•
Change the characters color and background color every 30 minutes
Ex)
•
Every 30 minutes, change the characters with movement.
Ex)
The best way to protect your monitor from Image retention is to set your PC or
System to operate a Screen Saver program when you are not using it.
Image retention may not occur when a LCD panel is operated under normal conditions.
Normal conditions are defined as continuously changing video patterns. When the
LCD panel is operated for a long time with a fixed pattern (-over 12 hours-), there
may be slight difference in voltage between electrodes that work the liquid crystal
(LC) in a pixel. The voltage difference between electrodes increases with time,
forcing the liquid crystal to lean. When this occurs, the previous image may be seen
when the pattern is changed.
To prevent this, the accumulated voltage difference must be decreased.
Information
Our LCD Monitor satisfies ISO13406-2 Pixel fault Class II
Appendix
Contact SAMSUNG WORLDWIDE
Note
If you have any questions or comments relating to Samsung products, please contact the
SAMSUNG customer care center.
North America
U.S.A
1-800-SAMSUNG(726-7864) http://www.samsung.com/us
CANADA
1-800-SAMSUNG(726-7864) http://www.samsung.com/ca
MEXICO
01-800-SAMSUNG
(726-7864)
http://www.samsung.com/mx
Latin America
ARGENTINA
0800-333-3733
http://www.samsung.com/ar
BRAZIL
0800-124-421
http://www.samsung.com/br
4004-0000
CHILE
800-SAMSUNG(726-7864)
http://www.samsung.com/cl
COLOMBIA
01-8000112112
http://www.samsung.com/co
COSTA RICA
0-800-507-7267
http://www.samsung.com/latin
ECUADOR
1-800-10-7267
http://www.samsung.com/latin
EL SALVADOR
800-6225
http://www.samsung.com/latin
GUATEMALA
1-800-299-0013
http://www.samsung.com/latin
HONDURAS
800-7919267
http://www.samsung.com/latin
JAMAICA
1-800-234-7267
http://www.samsung.com/latin
NICARAGUA
00-1800-5077267
http://www.samsung.com/latin
PANAMA
800-7267
http://www.samsung.com/latin
PUERTO RICO
1-800-682-3180
http://www.samsung.com/latin
REP. DOMINICA
1-800-751-2676
http://www.samsung.com/latin
TRINIDAD & TO- 1-800-SAMSUNG(726-7864) http://www.samsung.com/latBAGO
in
VENEZUELA
0-800-100-5303
http://www.samsung.com/latin
Europe
AUSTRIA
0810 - SAMSUNG(7267864, http://www.samsung.com/at
€ 0.07/min)
Appendix
Europe
BELGIUM
02 201 2418
http://www.samsung.com/be
(Dutch)
http://www.samsung.com/
be_fr
(French)
CZECH REPUBLIC 800
(800-726786)
SAMSUNG http://www.samsung.com/cz
DENMARK
8 - SAMSUNG (7267864)
http://www.samsung.com/dk
EIRE
0818 717 100
http://www.samsung.com/ie
FINLAND
30 - 6227 515
http://www.samsung.com/fi
FRANCE
3260 dites ' SAMSUNG '(€ http://www.samsung.com/fr
0,15/Min)
0825 08 65 65 (€ 0.15/Min)
GERMANY
01805
SAMSUNG http://www.samsung.de
(7267864, € 0.14/Min)
HUNGARY
06-80-SAMSUNG(726-7864) http://www.samsung.com/hu
ITALIA
800-SAMSUNG(726-7864)
http://www.samsung.com/it
LUXEMBURG
02 261 03 710
http://www.samsung.com/lu
NETHERLANDS
0900
SAMSUNG http://www.samsung.com/nl
(0900-7267864)( € 0.10/Min)
NORWAY
3 - SAMSUNG (7267864)
POLAND
0 - 801
(172678)
-
http://www.samsung.com/no
1SAMSUNG http://www.samsung.com/pl
022 - 607 - 93 - 33
PORTUGAL
808
20
(7267864)
-
SAMSUNG http://www.samsung.com/pt
SLOVAKIA
0800-SAMSUNG(726-7864) http://www.samsung.com/sk
SPAIN
902 - 1 - SAMSUNG (902 172 http://www.samsung.com/es
678)
SWEDEN
075 - SAMSUNG (726 78 64) http://www.samsung.com/se
SWITZERLAND
0848-SAMSUNG(7267864,
CHF 0.08/min)
http://www.samsung.com/ch
U.K
0845 SAMSUNG (7267864)
http://www.samsung.com/uk
CIS
ESTONIA
800-7267
http://www.samsung.com/ee
LATVIA
8000-7267
http://www.samsung.com/lv
LITHUANIA
8-800-77777
http://www.samsung.com/lt
KAZAKHSTAN
8-10-800-500-55-500
http://www.samsung.com/
kz_ru
KYRGYZSTAN
00-800-500-55-500
RUSSIA
8-800-555-55-55
http://www.samsung.ru
Appendix
CIS
TADJIKISTAN
8-10-800-500-55-500
UKRAINE
8-800-502-0000
http://www.samsung.ua
UZBEKISTAN
8-10-800-500-55-500
http://www.samsung.com/
kz_ru
Asia Pacific
AUSTRALIA
1300 362 603
http://www.samsung.com/au
CHINA
800-810-5858
http://www.samsung.com/cn
400-810-5858
010-6475 1880
INDIA
HONG KONG:3698 - 4698
http://www.samsung.com/hk
3030 8282
http://www.samsung.com/in
1800 110011
1-800-3000-8282
INDONESIA
0800-112-8888
http://www.samsung.com/id
JAPAN
0120-327-527
http://www.samsung.com/jp
MALAYSIA
1800-88-9999
http://www.samsung.com/my
NEW ZEALAND
0800 SAMSUNG (0800 726 http://www.samsung.com/nz
786)
PHILIPPINES
1-800-10-SAMSUNG
(726-7864)
http://www.samsung.com/ph
1-800-3-SAMSUNG
(726-7864)
02-5805777
SINGAPORE
1800-SAMSUNG(726-7864) http://www.samsung.com/sg
THAILAND
1800-29-3232
http://www.samsung.com/th
02-689-3232
TAIWAN
0800-329-999
http://www.samsung.com/tw
VIETNAM
1 800 588 889
http://www.samsung.com/vn
Middle East & Africa
SOUTH AFRICA
0860-SAMSUNG(726-7864) http://www.samsung.com/za
TURKEY
444 77 11
http://www.samsung.com/tr
U.A.E
800-SAMSUNG(726-7864)
http://www.samsung.com/ae
8000-4726
Terms
Dot Pitch
The image on a monitor is composed of red, green and blue
dots. The closer the dots, the higher the resolution. The distance between two dots of the same color is called the 'Dot
Pitch'. Unit: mm
Appendix
Vertical Frequency
The screen must be redrawn several times per second in
order to create and display an image for the user. The frequency of this repetition per second is called the Vertical
Frequency or Refresh Rate. Unit: Hz
Example: If the same light repeats itself 60 times per second, this is regarded as 60 Hz.
Horizontal Frequency
The time to scan one line connecting the right edge to the
left edge of the screen horizontally is called the Horizontal
Cycle. The inverse number of the Horizontal Cycle is called
Horizontal Frequency. Unit: kHz
Interlace and Non-Interlace
Methods
Showing the horizontal lines of the screen from the top to
the bottom sequentially is called the Non-Interlace method
while showing odd lines and then even lines in turn is called
the Interlace method. The Non-Interlace method is used for
the majority of monitors to ensure a clear image. The Interlace method is the same as that used in TVs.
Plug & Play
This is a function that provides the best quality screen for
the user by allowing the computer and the monitor to exchange information automatically. This monitor follows the
international standard VESA DDC for the Plug & Play function.
Resolution
The number of horizontal and vertical dots used to compose
the screen image is called the 'resolution'. This number
shows the accuracy of the display. A high resolution is good
for performing multiple tasks as more image information can
be shown on the screen.
Example: If the resolution is 1360 x 768(1920 x 1080) , this
means the screen is composed of 1360 (1920 )horizontal
dots (horizontal resolution) and 768(1080) vertical lines
(vertical resolution).
Correct Disposal
Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking on the product, accessories or literature
indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not
be disposed of with other household waste at the end
of their working life. To prevent possible harm to the
environment or human health from uncontrolled
waste disposal, please separate these items from
other types of waste and recycle them responsibly to
promote the sustainable reuse of material resources.
Household users should contact either the retailer
where they purchased this product, or their local government office, for details of where and how they can
take these items for environmentally safe recycling.
Appendix
Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
Business users should contact their supplier and
check the terms and conditions of the purchase contract. This product and its electronic accessories
should not be mixed with other commercial wastes
for disposal.
Authority
Information in this document is subject to change without notice.
© 2009 Samsung Electronics Co., Ltd. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co., Ltd. is strictly forbidden.
Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental
or consequential damages in connection with the furnishing, performance, or use of this material.
Samsung is the registered trademark of Samsung Electronics Co., Ltd.; Microsoft, Windows
and Windows NT are registered trademarks of Microsoft Corporation; VESA, DPM and DDC
are registered trademarks of Video Electronics Standard Association; the ENERGY STAR®
name and logo are registered trademarks of the U.S. Environmental Protection Agency
(EPA). As an ENERGY STAR® Partner, Samsung Electronics Co., Ltd. has determined that
this product meets the ENERGY STAR® guidelines for energy efficiency. All other product
names mentioned herein may be the trademarks or registered trademarks of their respective
owners.
Download PDF

advertising