Samsung | 933SN | Samsung 933SN User Manual

LCD Monitor
User Manual
Safety Instructions
Notational
Note
These safety instructions must be followed to ensure your safety and prevent property damage.
Make sure to read the instructions carefully and use the product in the correct manner.
Warning / Caution
Otherwise, it may result in death or personal injury.
Otherwise, it may result in personal injury or property damage.
Notational Conventions
Prohibited
Important to read and understand at all times
Do not disassemble
Disconnect the plug from the
outlet
Do not touch
Ground to prevent an electric
shock
Power
When not used for extended period of time, set your computer to DPM.
If using screen saver, set it to active screen mode.
The images here are for reference only, and are not applicable in all cases (or
countries).
Shortcut to Anti-Afterimage Instructions
Do not use a damaged power cord or plug or a damaged or loose power
outlet.
•
Otherwise, this may result in electric shock or fire.
Do not touch the power plug with wet hands when removing or plugging the plug into the outlet.
•
Otherwise, this may result in electric shock.
Make sure to connect the power cord to a grounded power outlet.
•
Otherwise, it may result in electric shock or personal injury.
1
Safety Instructions
Ensure that the power plug is plugged into the power outlet firmly and
correctly.
•
Otherwise, this may result in fire.
Do not forcefully bend or pull the power plug and do not place any
heavy material on it.
•
Otherwise, this may result in fire.
Do not connect multiple appliances to the same power outlet.
•
Otherwise, this may cause fire due to overheating.
Do not disconnect the power cord while using the monitor.
•
Otherwise, this may result in damage to the product due to electric
shock.
To disconnect the apparatus from the mains, the plug must be pulled
out from the mains socket, therefore the mains plug shall be readily operable.
•
This may cause electric shock or fire.
Use only the power cord provided by our company. Do not use the
provided power cord of another product.
•
Otherwise, this may result in fire or electric shock.
Installation
Be sure to contact an authorized Service Center when installing your monitor in
a location with heavy dust, high or low temperatures, high humidity, and exposed
to chemical substances and where it operates for 24 hours such as at airports,
train stations etc.
Failure to do so may cause serious damage to your monitor.
Do not drop the monitor when moving it.
•
This may cause damage to the product or the person carrying it.
When installing the product in a cabinet or rack, make sure that the
front end of the bottom of the product does not project out.
•
Otherwise, it may fall or cause personal injury.
•
Use a cabinet or rack of a size appropriate to the product.
DO NOT PLACE CANDLES,MOSQUITO REPELLANT,CIGARETTES AND ANY HEATING APPLIANCES NEAR THE PRODUCT.
•
Otherwise, this may cause fire.
2
Safety Instructions
Keep heating appliances as far away from the power cord or the product as possible.
•
Otherwise, this may result in electric shock or fire.
Do not install it in a badly ventilated location such as a bookcase or
closet.
•
Otherwise, this may result in fire due to an increase in the internal
temperature.
Put down the monitor carefully.
•
Failing to do so may damage the monitor.
Do not place the front of the product on the floor.
•
Otherwise, this may result in damage to the screen display.
Ensure that an authorized installation company installs the wall mount.
•
Otherwise, it may fall and cause personal injury.
•
Make sure to install the specified wall mount.
Install your product in a well ventilated location. Ensure that there is
a clearance of more than 10 cm from the wall.
•
Otherwise, it may result in fire due to an increase in the internal temperature.
Ensure that the packaging vinyl is kept away from children.
•
Otherwise, it may result in serious harm (suffocation) if children play
with it.
If the height of your monitor is adjustable, do not place any object or
part of your body on the stand when lowering it.
•
This may cause damage to the product or the person carrying it.
Clean
When cleaning the monitor case or the surface of the TFT-LCD screen, wipe
with a slightly moistened, soft fabric.
Do not spray cleaner directly onto the surface of the product.
•
Otherwise, this may result in the discoloration and distortion of the
structure and the screen surface may peel off.
Clean the product using a soft cloth with a monitor cleaner only. If
you must use a cleaner other than the monitor cleaner, dilute it with water
at a ratio of 1:10.
3
Safety Instructions
When cleaning the power plug pins or dusting the power outlet, clean
it with a dry cloth.
•
Otherwise, it may result in fire.
When cleaning the product, make sure to disconnect the power cord.
•
Otherwise, it may result in electric shock or fire.
When cleaning the product, disconnect the power cord and clean it
softly with a dry cloth.
•
(Do not use chemicals such as wax, benzene, alcohol, thinner, mosquito repellant, lubricant, or cleaner.) These may change the appearance of the product surface and peel off the indication labels on the
product.
Since the product housing is easily scratched, make sure to use the
specified cloth only.
•
Use the specified cloth adding only a little water. As the product may
be scratched if there is any foreign material on the cloth, make sure
to shake it thoroughly before using it.
When cleaning the product, do not spray water directly onto the main
body of the product.
•
Ensure that water does not enter the product and that it is not wet.
•
Otherwise, this may result in electric shock, fire or a malfunction.
Others
The product is a high voltage product. Ensure that users do not disassemble, repair or modify the product themselves.
•
Otherwise, this may result in electric shock or fire. If the product
needs to be repaired, contact a Service Center.
If there is a strange smell or a strange sound or smoke is coming from
the product, disconnect the power plug immediately and contact a Service
Center.
•
Otherwise, this may result in electric shock or fire.
Do not place this product in a location exposed to moisture, dust,
smoke, water, or in a car.
•
Otherwise, this may result in electric shock or fire.
When you drop the product or the case is broken, turn the power off
and disconnect the power cord. Contact a Service Center.
•
Otherwise, this may result in electric shock or fire.
4
Safety Instructions
If thunder or lightening is occurring, do not touch the power cord or
antenna cable.
•
Otherwise, this may result in electric shock or fire.
Do not try to move the monitor by pulling only the wire or the signal
cable.
•
Otherwise, it may fall and result in electric shock, damage to the
product or fire due to damage to the cable.
Do not lift or move the product back and forwards or right and left
while only holding the power cord or signal cables.
•
Otherwise, it may fall and result in electric shock, damage to the
product or fire due to damage to the cable.
Make sure that the ventilating opening is not blocked by a table or
curtain.
•
Otherwise, it may result in fire due to an increase in the internal temperature.
Do not place any containers containing water, vases, flowerpots, medicines as well as any metal on the product.
•
If water or a foreign material enters the product, disconnect the power
cord and contact a Service Center.
•
This may result in a product malfunction, electric shock, or fire.
Do not use or keep combustible spray or flammable material near the
product.
•
Otherwise, this may result in an explosion or fire.
Do not insert any metal, such as chopsticks, coins, pins and steel, or
flammable objects, such as matches or paper, inside the product (through
the ventilating openings, input and output terminals, etc).
•
If water or foreign material enters the product, disconnect the power
cord and contact a Service Center.
•
Otherwise, this may result in electric shock or fire.
When using a fixed screen for a long time, an afterimage or stain may
occur.
•
If you are not using your product for a long period of time, put it into
sleep mode or use a moving screen saver.
Set a resolution and frequency appropriate to the product.
•
Otherwise, your eyesight may be damaged.
Keep the volume at a comfortable level when using the headphones.
•
Excessively loud volume level may damage hearing.
5
Safety Instructions
If you continually move closer to the product screen, your eyesight
may be failing.
To ease eye strain, take at least a five-minute break after every hour
of using the monitor.
Do not install it in an unstable location such as an unstable rack or
uneven surface or a location exposed to vibrations.
•
Otherwise, it may fall and cause personal injury and/or damage the
product.
•
If you use the product in a location exposed to vibrations, it may
damage the product and result in fire.
When moving the product, turn the power off and disconnect the power
plug, antenna cable, and all the cables connected to the product.
•
Otherwise, it may result in electric shock or fire.
Ensure that children do not hang onto the product or climb up onto the
product.
•
The product may fall and cause personal injury or death.
If you do not use the product for a long period of time, disconnect the
power cord from the power outlet.
•
Otherwise, this may result in overheating or fire due to dust, and may
result in fire due to electric shock or leakage.
Do not place any heavy items or toys or confectionery, such as cookies
etc. that may attract the attention of children and to the product.
•
Your children may hang onto the product causing it to fall and this
may result in personal injury or death.
Do not turn the product upside down or move it while holding only
the stand.
•
Otherwise, it may fall and result in personal injury and/or damage to
the product.
Do not place the product in a location exposed to direct sunlight or
near any heat such as a fire or heater.
•
This may reduce the lifetime of the product, and may result in fire.
Do not drop any objects onto the product or cause any impact to the
product.
•
Otherwise, this may result in electric shock or fire.
6
Safety Instructions
Do not use a humidifier or kitchen table near the product.
•
Otherwise, this may result in electric shock or fire.
When there is a gas leak, do not touch the product or the power plug
but ventilate immediately.
•
If a spark occurs, it may cause an explosion or fire.
If the product has been turned on for a long time, the display panel
becomes hot. Do not touch it.
•
Keep the small accessories in a location out of the reach of children.
Be careful when adjusting the angle of the product or the height of the
stand.
•
This may result in personal injury as your hand or fingers may become caught.
•
Also, if you tilt the product too far, it may fall and cause personal
injury.
Do not install the product in a location low enough for children to
reach.
•
Otherwise, it may fall and result in personal injury.
•
Since the front part of the product is heavy, install the product on a
level and stable surface.
Do not put any heavy objects on the product.
•
This may result in personal injury and/or damage to the product.
Good Postures When Using the Monitor
When using the product, use it in the correct position.
•
Keep your back straight while looking at the product.
•
The distance between your eyes and the screen should
be between 45 to 50 cm. Look at the screen from a
slightly higher location than the height of the screen.
•
When using the product, use it in the correct position.
•
Adjust the angle so that light is not reflected on the
screen.
•
Place your arms perpendicular to your sides and allow
your arms to be level with the back of the hand.
•
Keep your elbow at 90 degrees.
•
Keep your knees at greater than 90 degrees, and keep
your heels firmly on the floor. Keep your arms lower
than your heart.
7
Introduction
Package Contents
Note
Please make sure the following items are included with your monitor.
If any items are missing, contact your dealer.
Contact a local dealer to buy optional items.
Unpacking
Monitor
Manuals
Quick Setup Guide
Warranty Card
User's Guide
(Not available in all locations)
Cables
D-Sub Cable
Power Cord
Cleaning Cloth(Option)
Cable holding ring
Others
8
DVI Cable (option)
Introduction
Note
Cleaning Cloth is only provided for highly polished black products as a product feature.
Your Monitor
Initial Settings
Select the language using the up or down key.
The displayed content will disappear after 40 seconds.
Turn the Power button off and on. It will be displayed again.
It can be displayed up to three (3) times. Make sure to adjust the resolution of your PC before reaching
the maximum count.
Note
The resolution displayed on the screen is the optimal resolution for this product.
Adjust your PC resolution so that it is the same as the optimal resolution for this product.
Front
MENU button [MENU/ ]
Opens the on-screen menu and exits from the menu. Also use to exit the OSD menu
or return to the previous menu.
Brightness button [ ]
When OSD is not on the screen, push the button to adjust brightness.
Customized Key[
]
9
Introduction
You can customize key assignment for the Custom button according to your preferences.
Note
You can configure the customized key for a required function via Setup > Customized Key.
Adjust buttons [
]
These buttons allow you to adjust items in the menu.
Enter button [
]
Activates a highlighted menu item.
Push the ' ', then selects the video signal while the OSD is off. (When the ' '
button is pressed to change the input mode, a message appears in the upper left of
the screen displaying the current mode -- analog or digital input signal.)
Note
•
If you select the digital mode, you must connect your monitor to the graphic
card's DVI port using the DVI cable.
•
This function is not available for products with an Analog interface only.
AUTO button
Usethis button for auto adjustment.
(Available in Analog mode only)
Power button [
]
Use this button for turning the product on and off.
Power Indicator
This light is lit when operating normally, and blinks once when your adjustments
are saved.
Note
See PowerSaver described in the manual for further information regarding power
saving functions. For energy conservation, turn your monitor OFF when it is not
needed or when leaving it unattended for long periods.
Rear
Note
The configuration at the back of the monitor may vary from product to product.
POWER port
10
Introduction
POWER port
Connect the power cord for your monitor to the
POWER port on the back of the product.
DVI IN
DVI IN
Connect the DVI Cable to the DVI IN port on the
back of your monitor.
Note
Applicable to the digital (DVI)-dedicated models
only.
RGB IN
RGB IN
Connect the D-sub cable to the 15-pin, RGB IN
port on the back of your monitor.
Kensington Lock
Kensington Lock
The Kensington lock is a device used to physically fix the system when using it in a public
place. (The locking device has to be purchased
separately.) For using a locking device, contact
where you purchase it.
Note
The location of the Kensington Lock may be different depending on its model.
Using the Anti-Theft Kensington Lock
1.
Insert the locking device into the Kensington
and turn it in the
slot on the Monitor
locking direction
11
.
Introduction
2.
Connect the Kensington Lock cable.
3.
Fix the Kensington Lock to a desk or a heavy
stationary object.
Note
See Connecting Cables for further information regarding cable connections.
Cable holding ring
•
Fix the cables using the holding ring, as shown in the figure.
12
Connections
Connecting Cables
Use a connection appropriate for your computer.
Using the D-sub (Analog) connector on the video card.
•
Connect the signal cable to the 15-pin, D-sub port on the back of your monitor.
Using the DVI (Digital) connector on the video card.
•
Connect the DVI Cable to the DVI IN Port on the back of your Monitor.
13
Connections
Connect the power cord for your monitor to the power port on the back of the monitor.
Plug the power cord for the monitor into a nearby outlet.
Note
If the monitor and the computer are connected, you can turn them on and use them.
Using the Stand
Folding the base
Note
You can tilt the monitor upwards at an angle of -1° to 16°. ( ±1.0°)
Attaching a Base
This monitor accepts a 100 mm x 100 mm VESA-compliant mounting interface pad.
Note
The VESA dimensions given above are an example. The VESA dimensions may differ depending on
the product.
14
Connections
A. Monitor
B. Mounting interface pad (Sold separately)
1.
Turn off your monitor and unplug its power cord.
2.
Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen.
3.
Remove the stand from the LCD monitor.
4.
Align the mounting interface pad with the holes in the rear cover mounting pad and secure it with
four screws that came with the arm-type base, wall mount hanger or other base.
•
Do not use screws longer than the standard dimension, as they may damage the
inside of the Monitor.
•
For wall mounts that do not comply with VESA standard screw specifications,
the length of the screws may differ depending on their specifications.
•
Do not use screws that do not comply with the VESA standard screw specifications.
Do not fasten the screws too tightly, as this may damage the product or cause the
product to fall, leading to personal injury.
Samsung is not liable for these kinds of accidents.
•
Samsung is not liable for product damage or personal injury when a non-VESA
or non-specified wall mount is used or the consumer fails to follow the product
installation instructions.
•
To mount the monitor on a wall, you should purchase the wall mounting kit that
allows you to mount the monitor at least 10 cm away from the wall surface.
•
Contact the nearest Samsung Service Center for more information. Samsung
Electronics will not be responsible for damages caused by using a base other than
those specified.
•
Please use Wall Mount according to the International standards.
15
Using the Software
Monitor Driver
Note
When prompted by the operating system for the monitor driver, insert the CD-ROM
included with this monitor. Driver installation is slightly different from one operating
system to another. Follow the directions appropriate for the operating system you
have.
Prepare a blank disk and download the driver program file at the Internet web site
shown here.
Internet web site :
http://www.samsung.com/ (Worldwide)
Installing the Monitor Driver (Automatic)
1.
Insert CD into the CD-ROM drive.
2.
Click "Windows".
3.
Choose your monitor model in the model list, then click the "OK" button.
4.
If you can see following message window, then click the "Continue Anyway" button. Then click
"OK" button (Microsoft® Windows® XP/2000 Operating System).
16
Using the Software
Note
This monitor driver is under certifying MS logo, and this installation doesn't damage your system.
The certified driver will be posted on Samsung Monitor homepage.
http://www.samsung.com/
Installing the Monitor Driver (Manual)
Microsoft® Windows Vista™‚ Operating System
1.
Insert your Manual CD into your CD-ROM drive.
2.
Click
3.
Click "Personalization" and then "Display Settings".
4.
Click "Advanced Settings...".
5.
Click "Properties" in the "Monitor" tab. If the "Properties" button is deactivated, it means the
configuration for your monitor is completed. The monitor can be used as is.
(Start) and "Control Panel". Then, double-click on "Appearance and Personalization".
If the message "Windows needs..." is displayed, as shown in the figure below, click "Continue".
17
Using the Software
Note
This monitor driver is under certifying MS logo, and this installation doesn't damage your system.
The certified driver will be posted on Samsung Monitor homepage.
6.
Click "Update Driver..." in the "Driver" tab.
7.
Check the "Browse my computer for driver software" checkbox and click "Let me pick from a
list of device drivers on my computer".
8.
Click "Have Disk...” and select the folder (for example, D:\Drive) where the driver setup file is
located, and click "OK".
18
Using the Software
9.
Select the model that matches your monitor from the list of monitor models on the screen, and
click "Next".
10. Click "Close" → "Close" → "OK" → "OK" on the following screens displayed in sequence.
Microsoft® Windows® XP Operating System
19
Using the Software
1.
Insert CD into the CD-ROM drive.
2.
Click "Start" → "Control Panel" then click the "Appearance and Themes" icon.
3.
Click "Display" icon and choose the "Settings" tab then click "Advanced...".
4.
Click the "Properties" button on the "Monitor" tab and select "Driver" tab.
5.
Click "Update Driver..." and select "Install from a list or..." then click "Next" button.
6.
Select "Don't search, I will..." then click "Next" and then click "Have disk".
20
Using the Software
7.
Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model
list and click the "Next" button.
8.
If you can see following message window, then click the "Continue Anyway" button. Then click
"OK" button.
Note
This monitor driver is under certifying MS logo, and this installation doesn't damage your system.
The certified driver will be posted on Samsung Monitor homepage.
http://www.samsung.com/
9.
Click the "Close" button then click "OK" button continually.
21
Using the Software
10. Monitor driver installation is completed.
Microsoft® Windows® 2000 Operating System
When you can see "Digital Signature Not Found" on your monitor, follow these steps.
1.
Choose "OK" button on the "Insert disk" window.
2.
Click the "Browse" button on the "File Needed" window.
3.
Choose A:(D:\Driver) then click the "Open" button and then click "OK" button.
How to install
1.
Click "Start", "Setting", "Control Panel".
2.
Double click the "Display" icon.
3.
Select the "Settings" tab and click "Advanced Properties" button.
4.
Choose "Monitor".
Case1 : If the "Properties" button is inactive, it means your monitor is properly configured. Please
stop installation
Case2 : If the "Properties" button is active, click the "Properties" button then follow next steps
continually.
5.
Click "Driver" and then click on "Update Driver..." then click on the "Next" button.
6.
Choose "Display a list of the known drivers for this device so that I can choose a specific driver"
then click "Next" and then click "Have disk".
7.
Click the "Browse" button then choose A:(D:\Driver).
8.
Click the "Open" button, then click "OK" button.
9.
Choose your monitor model and click the "Next" button then click "Next" button.
10. Click the "Finish" button then the "Close" button.
If you can see the "Digital Signature Not Found" window then click the "Yes" button. And click
the "Finish" button then the "Close" button.
Microsoft® Windows® Millennium Operating System
1.
Click "Start", "Setting", "Control Panel".
2.
Double click the "Display" icon.
3.
Select the "Settings" tab and click "Advanced Properties" button.
22
Using the Software
4.
Select the "Monitor" tab.
5.
Click the "Change" button in the "Monitor Type" area.
6.
Choose "Specify the location of the driver".
7.
Choose "Display a list of all the driver in a specific location..." then click "Next" button.
8.
Click the "Have Disk" button.
9.
Specify A:\(D:\driver) then click "OK" button.
10. Select "Show all devices" and choose the monitor that corresponds to the one you connected to
your computer and click "OK".
11. Continue choosing "Close" button and "OK" button until you close the Display Properties dialogue box.
Microsoft® Windows® NT Operating System
1.
Click "Start", "Settings", "Control Panel", and then double-click "Display" icon.
2.
In Display Registration Information window, click Settings Tab and then click "All Display
Modes".
3.
Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency) and
then click "OK".
4.
Click "Apply" button if you see the screen working normally after clicking "Test". If the screen
is not normal, change to a different mode (lower mode of resolution, colors or frequency).
Note
If there is no Mode at All Display Modes, select the level of resolution and vertical frequency by
referring to the Preset Timing Modes in the user guide.
Linux Operating System
To execute X-Window, you need to make the X86Config file, which is a type of system setting file.
1.
Press "Enter" at the first and the second screen after executing the X86Config file.
2.
The third screen is for setting your mouse.
3.
Set a mouse for your computer.
4.
The next screen is for selecting a keyboard.
5.
Set a Keyboard for your computer.
6.
The next screen is for setting your monitor.
7.
First of all, set a horizontal frequency for your monitor. (You can enter the frequency directly.)
8.
Set a vertical frequency for your monitor. (You can enter the frequency directly.)
9.
Enter the model name of your monitor. This information will not affect the actual execution of
X-Window.
10. You have finished setting up your monitor. Execute X-Window after setting other requested
hardware.
23
Using the Software
Natural Color
Natural Color Software Program
One of the recent problems in using a computer is that the color of the images printed out by a printer
or other images scanned by a scanner or a digital camera are not the same as those shown on the monitor.
The Natural Color S/W is the very solution for this problem. It is a color administration system developed by Samsung Electronics in association with Korea Electronics & Telecommunications
Research Institute (ETRI). This system is available only for Samsung monitors and makes the color
of the images on the monitor the same as the printed or scanned images. For more information, refer
to Help (F1) in the software program.
The Natural Color is provided online. You can download it from the website below and install;
http://www.samsung.com/us/consumer/learningresources/monitor/naturalcolorexpert/pop_download.html
MagicTune™
Installation
1.
Insert the installation CD into the CD-ROM drive.
2.
Click the MagicTune™ installation file.
Note
If the popup window to install the software for the main screen is not displayed, proceed with the
installation using the MagicTune executable file on the CD.
3.
Select installation Language, Click "Next".
4.
When the Installation Shield Wizard window appears, click "Next".
5.
Select "I agree to the terms of the license agreement" to accept the terms of use.
6.
Choose a folder to install the MagicTune™ program.
7.
Click "Install".
8.
The "Installation Status" window appears.
9.
Click "Finish".
24
Using the Software
10. When the installation is complete, the MagicTune™ executable icon appears on your desktop.
Double-click the icon to start the program.
MagicTune™ execution icon may not appear depending on specification of computer system or monitor. If that happens, press F5 Key.
Installation Problems
The installation of MagicTune™ can be affected by such factors as the video card, motherboard and
the network environment.
System Requirements
OS
•
Windows 2000
•
Windows XP Home Edition
•
Windows XP Professional
•
Windows Vista™
It is recommended using MagicTune™ in Windows® 2000 or later.
Hardware
•
32 MB Memory above
•
60 MB Hard disk space above
For more information, visit the MagicTune™ website.
Uninstall
The MagicTune™ program can be removed only by using the "Add or Remove Programs" option of
the Windows® Control Panel.
Perform the following steps remove MagicTune™.
1.
Go to [Task Tray] → [Start] → [Settings] and select [Control Panel] in the menu. If the program
runs on Windows® XP, go to [Control Panel] in the [Start] menu.
2.
Click the "Add or Remove Programs" icon in Control Panel.
3.
In the "Add or Remove Programs" screen, scroll down to find "MagicTune™." Click on it to
highlight it.
4.
Click the "Change/Remove" button to remove the program.
5.
Click "Yes" to begin the uninstall process.
6.
Wait until the "Uninstall Complete" dialog box appears.
Note
Visit the MagicTune™ website for technical support for MagicTune™, FAQs (questions and answers)
and software upgrades.
25
Using the Software
MultiScreen
Note
The software may not be supported depending on the model.
Installation
1.
Insert the installation CD into the CD-ROM drive.
2.
Click the MultiScreen installation file.
Note
If the popup window to install the software for the main screen is not displayed, proceed with the
installation using the MultiScreen executable file on the CD.
3.
When the Installation Shield Wizard window appears, click "Next".
4.
Select "I agree to the terms of the license agreement" to accept the terms of use.
5.
Choose a folder to install the MultiScreen‚ program.
6.
Click "Install".
7.
The "Installation Status" window appears.
8.
Click "Finish".
9.
When the installation is complete, the Multiscreen executable icon appears on your desktop.
Double-click the icon to start the program.
Multiscreen execution icon may not appear depending on specification of computer system
or monitor. If that happens, press F5 Key.
Installation Problems
The installation of MultiScreen can be affected by such factors as the video card, motherboard and the
network environment.
26
Using the Software
System Requirements
OS
•
Windows 2000
•
Windows XP Home Edition
•
Windows XP Professional
•
Windows Vista™
It is recommended using MultiScreen in Windows® 2000 or later.
Hardware
•
32 MB Memory above
•
60 MB Hard disk space above
Uninstall
The Multiscreen program can be removed only by using the "Add or Remove Programs" option of the
Windows® Control Panel.
Perform the following steps remove Multiscreen.
Select "Setting/Control Panel" on the "Start" menu and then double-click "Add/Delete a program".
Select Multiscreen from the list and then click the "Add/Delete" button.
27
Adjusting the Monitor
Direct Functions
AUTO
When the 'AUTO' button is pressed, the auto adjustment screen appears as shown in the animated
screen on the center.
Auto adjustment allows the monitor to self-adjust to the incoming Analog signal. The values of Fine,
Coarse and Position are adjusted automatically.
(Available in Analog mode only, so “AUTO” icon of OSD is gray in Digital mode.)
If auto adjustment does not work properly, press 'AUTO' button again to adjust picture with more
accuracy.
If you change resolution in the control panel, auto function will be executed automatically.
OSD Lock & Unlock
This is the function that locks the OSD in order to keep the current states of settings or prevent others
from adjusting the current settings.
Lock : Hold down the MENU button for more than five (5) seconds to activate the OSD adjustment
lock function.
Unlock : Hold down the MENU button for more than five (5) seconds to deactivate the OSD adjustment
lock function.
When pressing the AUTO button after locking the OSD
When pressing the MENU button after locking the OSD
Note
Though the OSD adjustment lock
function is activated, you can still
adjust the brightness and contrast,
and adjust Customized Key
(
) using the Direct button.
Customized key
You can customize key assignment for the Custom button according to your preferences.
28
Adjusting the Monitor
To view the operating screen displayed when pressing the [
tomized key for a function, click the name of each function.
] button after configuring the cus-
(MagicBright - MagicColor - Color Effect - Image Size)
Note
You can configure the customized
key for a required function via
Setup > Customized Key.
ImageSize : Supplied for the
wide models only such as 16:9 or
16:10.
Brightness
When OSD is not on the screen, push the Brightness (
) button to adjust brightness.
SOURCE
Selects the video signal while the OSD is off.
Note
Not applicable to analogue
(D-SUB)-or-digital (DVI)dedicated models.
OSD Function
Top Menus
Sub Menus
PICTURE Brightness
Contrast
Sharpness
MagicBright
Coarse
Red
Green
Blue
Color Tone
Fine
COLOR
MagicColor
Color Ef- Gamma
fect
29
Adjusting the Monitor
SIZE
POSITION
& H-Position
SETUP&RESET
V-Position
Image Size Menu H-Po- Menu V-Position
sition
Reset
Menu Trans- Language
parency
Off Timer Off Timer
On/Off
Setting
Auto
Source
PC/AV Mode Display
Time
Customized
Key
INFORMATION
Picture
Menu
Description
Brightness
(Not available in MagicBright mode of Dynamic Contrast.)
You can use the on-screen menus to change the brightness according
to personal preference.
The larger the number, the brighter the screen. The smaller the number,
the darker the screen.
Contrast
(Not available in MagicBright mode of Dynamic Contrast.)
You can use the on-screen menus to change the contrast according to
personal preference.
The larger the number, the brighter the screen. The smaller the number,
the darker the screen.
( Not available in MagicColor mode of Full and Intelligent. )
Sharpness
Changes the clearance of image.
The larger the number, the clearer the screen. The smaller the number,
the less clear the screen.
( Not available in MagicColor mode of Full and Intelligent. )
MagicBright
Push the
button to circle through available preconfigured modes.
MagicBright is a new feature providing optimum viewing environment
depending on the contents of the image you are watching. Currently
seven different modes are available: Custom, Text, Internet, Game,
Sport, Movie and Dynamic Contrast. Each mode has its own pre-
30
Adjusting the Monitor
Menu
Description
configured brightness value. You can easily select one of seven settings
by simply pressing Customized Key control button.
•
Custom
Although the values are carefully chosen by our engineers, the preconfigured values may not be comfortable to your eyes depending
on your taste.
If this is the case, adjust the brightness and contrast by using the
OSD menu.
•
Text
For documentations or works involving heavy text.
•
Internet
For working with a mixture of images such as texts and graphics.
•
Game
For watching motion pictures such as a game.
•
Sport
For watching motion pictures such as a sport.
•
Movie
For watching motion pictures such as a DVD or Video CD.
•
Dynamic Contrast
Dynamic Contrast is to automatically detect distribution of inputted visual signal and adjust to create optimum contrast.
Coarse
Removes noise such as vertical stripes.
The larger the number, the more the screen increases vertically. The
smaller the number, the more the screen decreases vertically.
Coarse adjustment may move the screen image area. You may relocate
it to the center using the horizontal control menu.
(Available in Analog mode only)
Fine
Removes noise such as horizontal stripes.
If the noise persists even after Fine tuning, repeat it after adjusting the
frequency (clock speed).
(Available in Analog mode only)
31
Adjusting the Monitor
Color
Menu
Description
MagicColor
MagicColor is a new technology that Samsung has exclusively developed to improve digital image and to display natural color more clearly
without disturbing image quality.
Red
•
Off - Returns to the original mode.
•
Demo - The screen before applying MagicColor appears on the
right and the screen after applying MagicColor appears on the left.
•
Full - Displays not only vivid natural color but also more realistic
natural skin color with clearness.
•
Intelligent - Displays vivid natural color with clearness.
Adjusts individual Red color balance.
The larger the number, the closer it is to red.
( Not available in MagicColor mode of Full and Intelligent. )
Green
Adjusts individual Green color balance.
The larger the number, the closer it is to green.
( Not available in MagicColor mode of Full and Intelligent. )
Blue
Adjusts individual Blue color balance.
The larger the number, the closer it is to blue.
( Not available in MagicColor mode of Full and Intelligent. )
Color Tone
The tone of the color can be changed and one of four modes can be
selected.
( Not available in MagicColor mode of Full and Intelligent. )
•
Cool - Makes whites bluish.
•
Normal - Keeps whites white.
•
Warm - Makes whites reddish.
•
Custom - Select this mode when you want to adjust the image according to your preferences.
32
Adjusting the Monitor
Menu
Description
Color Effect
You can change the overall mood by changing the screen colors.
( Not available in MagicColor mode of Full and Intelligent. )
Gamma
•
Off - This applies an achromatic color to the screen to adjust the
screen effects.
•
Grayscale - The default colors of black and white are displayed.
•
Green - This applies the green color effect to a black and white
screen.
•
Aqua - This applies the aqua color effect to a black and white
screen.
•
Sepia - This applies the Sepia color effect to a black and white
screen.
Gamma correction changes the luminance of the colors with intermediate luminance.
•
Mode 1 : Sets the screen to the default brightness.
•
Mode 2 : Sets the screen to bright.
•
Mode 3 : Sets the screen to dim.
SIZE & POSITION
Menu
Description
H-Position
Changes the horizontal position of the monitor's entire display.
You can move the position of the screen to the left and right by pressing
the and buttons, respectively.
(Available in Analog mode only)
Note
When TV signal is input in AV mode ,select “Screen Fit “to adjust
horizontal position in 0-6 levels.
V-Position
Changes the vertical position of the monitor's entire display.
You can move the position of the screen downwards and upwards by
pressing the and buttons, respectively.
33
Adjusting the Monitor
Menu
Description
(Available in Analog mode only)
Note
When TV signal is input in AV mode ,select “Screen Fit “to adjust
vertical position in 0-6 levels.
Image Size
Note
Supplied for the wide models only such as 16:9 or 16:10.
You can change the size of the screen displayed on your monitor.
PC signals
•
Auto - The screen is displayed in accordance with the screen aspect
ratio of the input signals.
•
Wide - A full screen is displayed regardless of the screen aspect
ratio of the input signals.
Note
•
Signals not available in the standard mode table are not supported.
•
If the wide screen which is the optimal resolution for the monitor
is set on your PC, this function is not performed.
AV signals
•
4 : 3 - Sets the picture to 4:3 normal mode.
•
16 : 9- Sets the picture to 16:9 wide mode.
•
Screen Fit- Use the function to see the full image without any cutoff
when DVI (480p/576p/720p/1080i/1080p) signals are input.
Note
It can only be selected if an external input is connected to the DVI
terminal and the 'PC/AV Mode' is set to 'AV'.
•
4 : 3 - Sets the picture to 4:3 normal mode.
•
Wide-Sets the picture to 16:10 wide mode.
•
Screen Fit- Use the function to see the full image without any cutoff
when DVI (480p/576p/720p/1080i/1080p) signals are input.
Note
•
It can only be selected if an external input is connected to the DVI
terminal and the 'PC/AV Mode' is set to 'AV'.
•
When the panel is of 16:10,the screen size options include
“4:3”,”wide “,”Screen fit“.
34
Adjusting the Monitor
SETUP&RESET
Menu
Description
Reset
Reverts the product settings to factory defaults.
•
Yes
•
No
Menu Transpar- Change the transparency of the background of the OSD.
ency
• Off : The menus are displayed in the normal way (non-transparently).
•
Language
On : The menus are displayed transparently.
You can select the language used to display the menus.
You can choose one of nine languages.
Note
The language chosen affects only the language of the OSD. It has no
effect on any software running on the computer.
Off Timer On/ You can enable or disable the Off Time function.
Off
• Off
•
On
Off Timer Setting The monitors will turn off automatically at the specified time.
Auto Source
Select Auto Source for the monitor to automatically select the signal
source.
•
Auto
•
Manual
Note
Not applicable to analogue (D-SUB)-or-digital (DVI)-dedicated models.
35
Adjusting the Monitor
Menu
Description
PC/AV Mode
This function allows the screen to be displayed at the optimal quality
in accordance with the size of the screen when a 480P, 576P, 720P,
1080i, or 1080P video signal is input in DVI mode.
Set to "PC" when connected to a PC, Set to "AV" when connected to
an AV device.
If not set to "AV", the screen may not be displayed normally.
(Unavailable in Analog mode)
Note
Supplied for the wide models only such as 16:9 or 16:10.
Display Time
The menu will be automatically turned off if no adjustments are made
for a certain time period.
You can set the amount of time the menu will wait before it is turned
off.
•
5 sec
•
10 sec
•
20 sec
•
200 sec
Customized Key You can specify a function which will be activated when the Customized Key (
)is pressed.
INFORMATION
Menu
Description
INFORMATION
Shows a video source, display mode on the OSD screen.
Note
For models with an Analog interface only, “Analog/Digital“is not
shown in the”Information”.
36
Troubleshooting
Self-Test Feature Check
Note
Your monitor provides a self test feature that allows you to check whether your monitor is functioning
properly.
Self-Test Feature Check
1.
Turn off both your computer and the monitor.
2.
Unplug the video cable from the back of the computer.
3.
Turn on the monitor.
If the monitor is functioning properly, you will see a box in the illustration below.
Note
For models with an Analog interface only, “Analog/Digital” is not shown in the Warning Message
OSD.
This box appears during normal operation if the video cable becomes disconnected or damaged.
4.
Turn off your monitor and reconnect the video cable; then turn on both your computer and the
monitor.
If your monitor screen remains blank after using the previous procedure, check your video controller
and computer system; your monitor is functioning properly.
Warning Messages
If there is something wrong with the input signal, a message appears on the screen or the screen goes
blank although the power indicator LED is still on. The message may indicate that the monitor is out
of scan range or that you need to check the signal cable.
Note
For models with an Analog interface only, “Analog/Digita” is not shown in the Warning Message
OSD.
37
Troubleshooting
Environment
The location and the position of the monitor may influence the quality and other features of the monitor.
If there are any sub woofer speakers near the monitor, unplug and relocate the woofer to another room.
Remove all electronic devices such as radios, fans, clocks and telephones that are within 3 feet (one
meter) of the monitor.
Useful Tips
A monitor recreates visual signals received from the computer. Therefore, if there is a problem with
the computer or the video card, this can cause the monitor to become blank, have poor coloring, become
noisy, and video mode not supported, etc. In this case, first check the source of the problem, and then
contact the Service Center or your dealer.
Judging the monitor's working condition
If there is no image on the screen or a "Not Optimum Mode", "Recommended Mode **** x ****
60 Hz" message comes up, disconnect the cable from the computer while the monitor is still powered
on.
If there is a message coming up on the screen or if the screen goes white, this means the monitor is in
working condition.
In this case, check the computer for trouble.
Check List
Note
Before calling for assistance, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the Information section or
contact your dealer.
No images on the screen. I cannot turn on the monitor.
Q:
Is the power cord connected properly?
A:
Check the power cord connection and supply.
Q:
Can you see "Check Signal Cable" on the screen?
A:
(Connected using the D-sub cable)
Check the signal cable connection.
(Connected using the DVI cable)
If you still see an error message on the screen when the monitor is connected properly, check to
see if the monitor status is set to analog.
If you still see an (error) message on the screen when the monitor is connected properly, check
to see if the monitor status is set to analog. Press ‘ ’ button to have the monitor double-check
the input signal source.
Q:
If the power is on, reboot the computer to see the initial screen (the login screen), which can be
seen.
A:
If the initial screen (the login screen) appears, boot the computer in the applicable mode (the
safe mode for Windows ME/XP/2000) and then change the frequency of the video card.
38
Troubleshooting
(Refer to the Preset Timing Modes)
If the initial screen (the login screen) does not appear, contact the Service Center or your dealer.
Q:
Can you see "Not Optimum Mode", "Recommended Mode **** x **** 60 Hz" on the screen?
A:
You can see this message when the signal from the video card exceeds the maximum resolution
and frequency that the monitor can handle properly.
A:
Adjust the maximum resolution and frequency that the monitor can handle properly.
A:
If the display exceeds SXGA or 75 Hz, a "Not Optimum Mode", "Recommended Mode ****
x **** 60 Hz" message is displayed. If the display exceeds 85 Hz, the display will work properly
but the "Not Optimum Mode", "Recommended Mode **** x **** 60 Hz" message appears
for one minute and then disappears.
Please change to the recommended mode during this one-minute period.
(The message is displayed again if the system is rebooted.)
Q:
There is no image on the screen. Is the power indicator on the monitor blinking at 1 second
intervals?
A:
The monitor is in PowerSaver mode.
A:
Press a key on the keyboard to activate the monitor and restore the image on the screen.
A:
If there is still no image, press the ' ' button. Then press any key on the keyboard again to
activate the monitor and restore the image on the screen.
Q:
Connected using the DVI cable?
A:
You may get a blank screen if you boot the system before you connect the DVI cable, or disconnect and then reconnect the DVI cable while the system is running as certain types of graphic
cards do not send out video signals. Connect the DVI cable and then reboot the system.
I cannot see the On Screen Display.
Q:
Have you locked the On Screen Display (OSD) Menu to prevent changes?
A:
Unlock the OSD by pressing the [MENU/
] button for at least 5 seconds.
The screen shows strange colors or just black and white.
Q:
Is the screen displaying only one color as if looking at the screen through a cellophane paper?
A:
Check the signal cable connection.
A:
Make sure the video card is fully inserted in its slot.
Q:
Have the screen colors become strange after running a program or due to a crash between applications?
A:
Reboot the computer.
Q:
Has the video card been set properly?
A:
Set the video card by referring to the video card manual.
39
Troubleshooting
The screen suddenly has become unbalanced.
Q:
Have you changed the video card or the driver?
A:
Adjust screen image position and size using the OSD.
Q:
Have you adjusted the resolution or frequency to the monitor?
A:
Adjust the resolution and frequency at the video card.
(Refer to the Preset Timing Modes)
Q:
The screen can be unbalanced due to the cycle of the video card signals. Readjust Position by
referring to the OSD.
The screen is out of focus or OSD cannot be adjusted.
Q:
Have you adjusted the resolution or frequency on the monitor?
A:
Adjust the resolution and frequency of the video card.
(Refer to the Preset Timing Modes)
LED is blinking but no images on the screen.
Q:
Is the frequency properly adjusted when checking the Display Timing on the menu?
A:
Adjust the frequency properly by referring to the video card manual and the Preset Timing
Modes.
(The maximum frequency per resolution may differ from product to product.)
There are only 16 colors shown on the screen. The screen colors have changed after changing
Q:
Have the Windows colors been set properly?
A:
Windows XP :
Set the resolution at the Control Panel → Appearance and Themes → Display → Settings.
A:
Windows ME/2000 :
Set the resolution at the Control Panel → Display → Settings.
Q:
Has the video card been set properly?
A:
Set the video card by referring to the video card manual.
There is a message that reads "Unrecognized monitor, Plug & Play (VESA DDC) monitor found"
Q:
Have you installed the monitor driver?
A:
Install the monitor driver according to the Driver Installation Instructions.
Q:
See the video card manual to see if the Plug & Play (VESA DDC) function can be supported.
A:
Install the monitor driver according to the Driver Installation Instructions.
My computer is on and the LED is blinking. However, only a blank screen is displayed on the mo
Q:
Check whether your computer is in hibernation mode (The monitor turns off).
40
Troubleshooting
A:
Move your mouse or press any key to display the screen again.
Problems related to Audio.
Q:
No sound.
A:
Ensure that the audio cable is firmly connected to both the audio-in port on your monitor and
the audio-out port on your sound card.
(Refer to Connecting Cables).
Check the volume level.
Q:
Sound level is too low.
A:
Check the volume level.
If the volume is still too low after turning the control to its maximum, check the volume control
on the computer sound card or software program.
Check when MagicTune™ does not function properly.
Q:
MagicTune™ feature is found only on PC (VGA) with Window OS that supports Plug and Play.
A:
To check whether your PC is available for MagicTune™ feature, follow the steps below (When
Windows is XP);
Control Panel → Performance and Maintenance → System → Hardware → Device Manager
→ Monitors → After deleting Plug and Play monitor, find 'Plug and Play monitor' by searching
new Hardware.
A:
MagicTune™ is an additional software for the monitor. Some graphic cards may not support
your monitor. When you have a problem with the graphic card, visit our website to check the
compatible graphic card list provided.
http://www.samsung.com/monitor/magictune
MagicTune™ doesn't work properly.
Q:
Have you changed your PC or video graphic card?
A:
Download the latest program. The program can be downloaded http://www.samsung.com/monitor/magictune
Q:
Did you install the program?
A:
Reboot the computer after installing the program for the first time. If a copy of the program is
already installed, remove it, reboot the computer, and then install the program again. You need
to reboot the computer for it to operate normally after installing or removing the program.
Note
Visit the MagicTune™ website and download the installation software for MagicTune™ MAC.
Check the following items if there is trouble with the monitor.
Check if the power cord and the video cables are properly connected to the computer.
Check if the computer beeps more than 3 times when booting.
(If it does, request an a service for the main board of the computer.)
41
Troubleshooting
If you installed a new video card or if you assembled the PC, check if the installed the adapter(video)
driver and the monitor driver.
Check if the scanning ratio of the video screen is set to between 56 Hz ~ 75 Hz.
(Do not exceed 75 Hz when using the maximum resolution.)
If you have problems in installing the adapter (video) driver, boot the computer in Safe Mode, remove
the Display Adapter in the "Control Panel → System → Device Administrator" and then reboot the
computer to reinstall the adapter (video) driver.
Note
If problems repeatedly occur, contact an authorized service center.
Q&A
Q:
How can I change the frequency?
A:
The frequency can be changed by reconfiguring the video card.
A:
Note that video card support can vary, depending on the version of the driver used. (Refer to the
computer or the video card manual for details.)
Q:
How can I adjusts the resolution?
A:
Windows XP:
Set the resolution in the Control Panel → Appearance and Themes → Display → Settings.
A:
Windows ME/2000:
Set the resolution in the Control Panel → Display → Settings.
* Contact the video card manufacturer for details.
Q:
How can I set the Power Saving function?
A:
Windows XP:
Set the resolution in the Control Panel → Appearance and Themes → Display → Screen Saver.
Set the function in the BIOS-SETUP of the computer. (Refer to the Windows / Computer Manual).
A:
Windows ME/2000:
Set the resolution at the Control Panel → Display → Screen Saver.
Set the function in the BIOS-SETUP of the computer. (Refer to the Windows / Computer Manual).
Q:
How can I clean the outer case/LCD Panel?
A:
Disconnect the power cord and then clean the monitor with a soft cloth, using either a cleaning
solution or plain water.
Do not leave any detergent or scratches on the case. Do not let any water enter the monitor.
42
Troubleshooting
Note
Before calling for assistance, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the Information section or
contact your dealer.
43
Specifications
General
General
Model Name
SyncMaster 633NW
LCD Panel
Size
15.6 inch (39 cm)
Display area
344.232 mm(H) x 193.536 mm(V)
Pixel Pitch
0.252 mm(H) x 0.252 mm(V)
Synchronization
Horizontal
30 ~ 61 kHz
Vertical
56 ~ 75 Hz
Display Color
16.7 M
Resolution
Optimum resolution
1360 x 768@60 Hz
Maximum resolution
1360 x 768@60 Hz
Input Signal, Terminated
RGB Analog,
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
90 MHz (Analog)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable, 1500 +/- 20 mm
Dimensions (W x H x D) / Weight (Simple Stand)
386 x 264.5 x 67.2 mm (15.2 x 10.4 x 2.6 inch) (Without Stand)
386 x 315.8 x 186.6 mm (15.2 x 12.4 x 7.3 inch) (With Stand)/ 2.55 kg (5.62 lbs)
VESA Mounting Interface
75 mm x 75 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 20 % ~ 80 %, non-condensing
Temperature : -4°F ~ 140°F (-20°C ~ 60°C)
Storage
Humidity : 10 % ~ 80 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the
computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor
installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth)
above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright
sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas
including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor
to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal
operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or
when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in
your computer. Use the software utility installed on your computer to set up this feature.
State
Normal Operation
Power saving mode
Power off (Power button)
EPA/ENERGY 2000
Power Indicator
On
Blinking
Off
Power Consumption
18 watts
Less than 1 watts
Less than 1 watts
This monitor is EPA ENERGY STAR® compliant and ENERGY 2000 compliant when used with
a computer equipped with VESA DPM functionality.
As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets the
ENERGY STAR® guidelines for energy efficiency.
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted
automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual
and adjusts the screen as follows.
Display Mode
Horizontal
Frequency
(kHz)
Vertical
Frequency (Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
IBM, 640 x 350
31.469
70.086
25.175
+/-
IBM, 640 x 480
31.469
59.940
25.175
-/-
IBM, 720 x 400
31.469
70.087
28.322
-/+
MAC, 640 x 480
35.000
66.667
30.240
-/-
MAC, 832 x 624
49.726
74.551
57.284
-/-
VESA, 640 x 480
37.861
72.809
31.500
-/-
VESA, 640 x 480
37.500
75.000
31.500
-/-
VESA, 800 x 600
35.156
56.250
36.000
+/+
VESA, 800 x 600
37.879
60.317
40.000
+/+
VESA, 800 x 600
48.077
72.188
50.000
+/+
VESA, 800 x 600
46.875
75.000
49.500
+/+
VESA, 1024 x 768
48.363
60.004
65.000
-/-
VESA, 1024 x 768
56.476
70.069
75.000
-/-
VESA, 1024 x 768
60.023
75.029
78.750
+/+
VESA, 1360 X 768
47.712
60.015
85.500
+/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the
screen horizontally is called the Horizontal Cycle and the inverse number of
the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times
per second to display an image to the user. The frequency of this repetition is
called the Vertical Frequency or Refresh Rate. Unit: Hz
Specifications
General
General
Model Name
SyncMaster 733A
LCD Panel
Size
17 inch (43 cm)
Display area
337.920 mm (H) x 270.336 mm (V)
Pixel Pitch
0.264 mm (H) x 0.264 mm (V)
Synchronization
Horizontal
30 ~ 81 kHz
Vertical
56 ~ 75 Hz
Display Color
16.7M
Resolution
Optimum resolution
1280 x 1024@60 Hz
Maximum resolution
1280 x 1024@75 Hz
Input Signal, Terminated
RGB Analog
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
135 MHz (Analog)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
380.6 x 349 x 72.3 mm / 15.0 x 13.7 x 2.8 inch (Without Stand)
380.6 x 397.1 x 200 mm / 15.0 x 15.6 x 7.9 inch (With Stand), 3.8 kg / 8.4 lbs
VESA Mounting Interface
75 mm x 75 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Storage
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the
computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor
installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth)
above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright
sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas
including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor
to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal
operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or
when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in
your computer. Use the software utility installed on your computer to set up this feature.
State
Normal Operation
Power saving mode
Power off (Power button)
EPA/ENERGY 2000
Power Indicator
On
Blinking
Off
Power Consumption
30 watts
Less than 1 watts
Less than 1 watts
This monitor is EPA ENERGY STAR® compliant and ENERGY2000 compliant when used with
a computer equipped with VESA DPM functionality.
As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets the
ENERGY STAR® guidelines for energy efficiency.
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted
automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual
and adjusts the screen as follows.
Display Mode
Horizontal
Frequency
(kHz)
Vertical
Frequency (Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
IBM,640 x 350
31.469
70.086
25.175
+/-
IBM,640 x 480
31.469
59.940
25.175
-/-
IBM,720 x 400
31.469
70.087
28.322
-/+
MAC,640 x 480
35.000
66.667
30.240
-/-
MAC,832 x 624
49.726
74.551
57.284
-/-
MAC,1152 x 870
68.681
75.062
100.000
-/-
VESA,640 x 480
37.861
72.809
31.500
-/-
VESA,640 x 480
37.500
75.000
31.500
-/-
VESA,800 x 600
35.156
56.250
36.000
+/+
VESA,800 x 600
37.879
60.317
40.000
+/+
VESA,800 x 600
48.077
72.188
50.000
+/+
VESA,800 x 600
46.875
75.000
49.500
+/+
VESA,1024 x 768
48.363
60.004
65.000
-/-
VESA,1024 x 768
56.476
70.069
75.000
-/-
VESA,1024 x 768
60.023
75.029
78.750
+/+
VESA,1152 x 864
67.500
75.000
108.000
+/+
VESA, 1280 X 960
60.000
60.000
108.000
+/+
VESA, 1280 X 1024
63.981
60.020
108.000
+/+
VESA, 1280 X 1024
79.976
75.025
135.000
+/+
VESA, 1280 X 800
49.702
59.810
83.500
-/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the
screen horizontally is called the Horizontal Cycle and the inverse number of
the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times
per second to display an image to the user. The frequency of this repetition is
called the Vertical Frequency or Refresh Rate. Unit: Hz
Specifications
General
General
Model Name
SyncMaster 733APLUS
LCD Panel
Size
17 inch (43 cm)
Display area
337.920 mm (H) x 270.336 mm (V)
Pixel Pitch
0.264 mm (H) x 0.264 mm (V)
Synchronization
Horizontal
30 ~ 81 kHz
Vertical
56 ~ 75 Hz
Display Color
16.7M
Resolution
Optimum resolution
1280 x 1024@60 Hz
Maximum resolution
1280 x 1024@75 Hz
Input Signal, Terminated
RGB Analog
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
135 MHz (Analog)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
380.6 x 349 x 72.3 mm / 15.0 x 13.7 x 2.8 inch (Without Stand)
380.6 x 397.1 x 200 mm / 15.0 x 15.6 x 7.9 inch (With Stand), 3.8 kg / 8.4 lbs
VESA Mounting Interface
75 mm x 75 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Storage
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the
computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor
installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth)
above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright
sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas
including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor
to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal
operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or
when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in
your computer. Use the software utility installed on your computer to set up this feature.
State
Normal Operation
Power saving mode
Power off (Power button)
EPA/ENERGY 2000
Power Indicator
On
Blinking
Off
Power Consumption
30 watts
Less than 1 watts
Less than 1 watts
This monitor is EPA ENERGY STAR® compliant and ENERGY2000 compliant when used with
a computer equipped with VESA DPM functionality.
As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets the
ENERGY STAR® guidelines for energy efficiency.
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted
automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual
and adjusts the screen as follows.
Display Mode
Horizontal
Frequency
(kHz)
Vertical
Frequency (Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
IBM,640 x 350
31.469
70.086
25.175
+/-
IBM,640 x 480
31.469
59.940
25.175
-/-
IBM,720 x 400
31.469
70.087
28.322
-/+
MAC,640 x 480
35.000
66.667
30.240
-/-
MAC,832 x 624
49.726
74.551
57.284
-/-
MAC,1152 x 870
68.681
75.062
100.000
-/-
VESA,640 x 480
37.861
72.809
31.500
-/-
VESA,640 x 480
37.500
75.000
31.500
-/-
VESA,800 x 600
35.156
56.250
36.000
+/+
VESA,800 x 600
37.879
60.317
40.000
+/+
VESA,800 x 600
48.077
72.188
50.000
+/+
VESA,800 x 600
46.875
75.000
49.500
+/+
VESA,1024 x 768
48.363
60.004
65.000
-/-
VESA,1024 x 768
56.476
70.069
75.000
-/-
VESA,1024 x 768
60.023
75.029
78.750
+/+
VESA,1152 x 864
67.500
75.000
108.000
+/+
VESA, 1280 X 960
60.000
60.000
108.000
+/+
VESA, 1280 X 1024
63.981
60.020
108.000
+/+
VESA, 1280 X 1024
79.976
75.025
135.000
+/+
VESA, 1280 X 800
49.702
59.810
83.500
-/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the
screen horizontally is called the Horizontal Cycle and the inverse number of
the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times
per second to display an image to the user. The frequency of this repetition is
called the Vertical Frequency or Refresh Rate. Unit: Hz
Specifications
General
General
Model Name
SyncMaster 733N
LCD Panel
Size
17 inch (43 cm)
Display area
337.920 mm (H) x 270.336 mm (V)
Pixel Pitch
0.264 mm (H) x 0.264 mm (V)
Synchronization
Horizontal
30 ~ 81 kHz
Vertical
56 ~ 75 Hz
Display Color
16.7M
Resolution
Optimum resolution
1280 x 1024@60 Hz
Maximum resolution
1280 x 1024@75 Hz
Input Signal, Terminated
RGB Analog
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
135 MHz (Analog)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
380.6 x 349 x 72.3 mm / 15.0 x 13.7 x 2.8 inch (Without Stand)
380.6 x 397.1 x 200 mm / 15.0 x 15.6 x 7.9 inch (With Stand), 3.8 kg / 8.4 lbs
VESA Mounting Interface
75 mm x 75 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Storage
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the
computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor
installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth)
above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright
sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas
including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor
to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal
operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or
when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in
your computer. Use the software utility installed on your computer to set up this feature.
State
Normal Operation
Power saving mode
Power off (Power button)
EPA/ENERGY 2000
Power Indicator
On
Blinking
Off
Power Consumption
30 watts
Less than 1 watts
Less than 1 watts
This monitor is EPA ENERGY STAR® compliant and ENERGY2000 compliant when used with
a computer equipped with VESA DPM functionality.
As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets the
ENERGY STAR® guidelines for energy efficiency.
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted
automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual
and adjusts the screen as follows.
Display Mode
Horizontal
Frequency
(kHz)
Vertical
Frequency (Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
IBM, 640 x 350
31.469
70.086
25.175
+/-
IBM, 640 x 480
31.469
59.940
25.175
-/-
IBM, 720 x 400
31.469
70.087
28.322
-/+
MAC, 640 x 480
35.000
66.667
30.240
-/-
MAC, 832 x 624
49.726
74.551
57.284
-/-
MAC, 1152 x 870
68.681
75.062
100.000
-/-
VESA, 640 x 480
37.861
72.809
31.500
-/-
VESA, 640 x 480
37.500
75.000
31.500
-/-
VESA, 800 x 600
35.156
56.250
36.000
+/+
VESA, 800 x 600
37.879
60.317
40.000
+/+
VESA, 800 x 600
48.077
72.188
50.000
+/+
VESA, 800 x 600
46.875
75.000
49.500
+/+
VESA, 1024 x 768
48.363
60.004
65.000
-/-
VESA, 1024 x 768
56.476
70.069
75.000
-/-
VESA, 1024 x 768
60.023
75.029
78.750
+/+
VESA, 1152 x 864
67.500
75.000
108.000
+/+
VESA, 1280 X 960
60.000
60.000
108.000
+/+
VESA, 1280 X 1024
63.981
60.020
108.000
+/+
VESA, 1280 X 1024
79.976
75.025
135.000
+/+
VESA, 1280 x 800
49.702
59.810
83.500
-/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the
screen horizontally is called the Horizontal Cycle and the inverse number of
the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times
per second to display an image to the user. The frequency of this repetition is
called the Vertical Frequency or Refresh Rate. Unit: Hz
Specifications
General
General
Model Name
SyncMaster 733NPLUS
LCD Panel
Size
17 inch (43 cm)
Display area
337.920 mm (H) x 270.336 mm (V)
Pixel Pitch
0.264 mm (H) x 0.264 mm (V)
Synchronization
Horizontal
30 ~ 81 kHz
Vertical
56 ~ 75 Hz
Display Color
16.7M
Resolution
Optimum resolution
1280 x 1024@60 Hz
Maximum resolution
1280 x 1024@75 Hz
Input Signal, Terminated
RGB Analog
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
135 MHz (Analog)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
380.6 x 349 x 72.3 mm / 15.0 x 13.7 x 2.8 inch (Without Stand)
380.6 x 397.1 x 200 mm / 15.0 x 15.6 x 7.9 inch (With Stand), 3.8 kg / 8.4 lbs
VESA Mounting Interface
75 mm x 75 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Storage
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the
computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor
installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth)
above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright
sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas
including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor
to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal
operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or
when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in
your computer. Use the software utility installed on your computer to set up this feature.
State
Normal Operation
Power saving mode
Power off (Power button)
EPA/ENERGY 2000
Power Indicator
On
Blinking
Off
Power Consumption
30 watts
Less than 1 watts
Less than 1 watts
This monitor is EPA ENERGY STAR® compliant and ENERGY2000 compliant when used with
a computer equipped with VESA DPM functionality.
As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets the
ENERGY STAR® guidelines for energy efficiency.
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted
automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual
and adjusts the screen as follows.
Display Mode
Horizontal
Frequency
(kHz)
Vertical
Frequency (Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
IBM, 640 x 350
31.469
70.086
25.175
+/-
IBM, 640 x 480
31.469
59.940
25.175
-/-
IBM, 720 x 400
31.469
70.087
28.322
-/+
MAC, 640 x 480
35.000
66.667
30.240
-/-
MAC, 832 x 624
49.726
74.551
57.284
-/-
MAC, 1152 x 870
68.681
75.062
100.000
-/-
VESA, 640 x 480
37.861
72.809
31.500
-/-
VESA, 640 x 480
37.500
75.000
31.500
-/-
VESA, 800 x 600
35.156
56.250
36.000
+/+
VESA, 800 x 600
37.879
60.317
40.000
+/+
VESA, 800 x 600
48.077
72.188
50.000
+/+
VESA, 800 x 600
46.875
75.000
49.500
+/+
VESA, 1024 x 768
48.363
60.004
65.000
-/-
VESA, 1024 x 768
56.476
70.069
75.000
-/-
VESA, 1024 x 768
60.023
75.029
78.750
+/+
VESA, 1152 x 864
67.500
75.000
108.000
+/+
VESA, 1280 X 960
60.000
60.000
108.000
+/+
VESA, 1280 X 1024
63.981
60.020
108.000
+/+
VESA, 1280 X 1024
79.976
75.025
135.000
+/+
VESA, 1280 x 800
49.702
59.810
83.500
-/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the
screen horizontally is called the Horizontal Cycle and the inverse number of
the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times
per second to display an image to the user. The frequency of this repetition is
called the Vertical Frequency or Refresh Rate. Unit: Hz
Specifications
General
General
Model Name
SyncMaster 733NW
LCD Panel
Size
17 inch (43 cm)
Display area
367.2 mm(H) x 229.5 mm(V)
Pixel Pitch
0.255 mm(H) x 0.255 mm(V)
Synchronization
Horizontal
30 ~ 81 kHz
Vertical
56 ~ 75 Hz
Display Color
16.2 M
Resolution
Optimum resolution
1440 x 900@60 Hz
Maximum resolution
1440 x 900@75 Hz
Input Signal, Terminated
RGB Analog,
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
136.75 MHz (Analog)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable, 1500 +/- 20 mm
Dimensions (W x H x D) / Weight (Simple Stand)
410.9 x 302.5 x 64.5 mm (16.2 x 11.9 x 2.5 inch) (Without Stand)
410.9 x 351.2 x 187 mm (16.2 x 13.8 x 7.4 inch) (With Stand)/ 2.8 kg (6.17 lbs)
VESA Mounting Interface
75 mm x 75 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 32 °F ~ 104°F (0°C ~ 40°C)
Operating
Humidity : 20 % ~ 80 %, non-condensing
Temperature : -4°F ~ 140°F (-20°C ~ 60°C)
Storage
Humidity : 10 % ~ 80 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the
computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor
installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth)
above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright
sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas
including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor
to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal
operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or
when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in
your computer. Use the software utility installed on your computer to set up this feature.
State
Normal Operation
Power saving mode
Power off (Power button)
EPA/ENERGY 2000
Power Indicator
On
Blinking
Off
Power Consumption
20 watts
Less than 1 watts
Less than 1 watts
This monitor is EPA ENERGY STAR® compliant and ENERGY 2000 compliant when used with
a computer equipped with VESA DPM functionality.
As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets the
ENERGY STAR® guidelines for energy efficiency.
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted
automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual
and adjusts the screen as follows.
Display Mode
Horizontal
Frequency
(kHz)
Vertical
Frequency (Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
IBM, 640 x 350
31.469
70.086
25.175
+/-
IBM, 640 x 480
31.469
59.940
25.175
-/-
IBM, 720 x 400
31.469
70.087
28.322
-/+
MAC, 640 x 480
35.000
66.667
30.240
-/-
MAC, 832 x 624
49.726
74.551
57.284
-/-
MAC, 1152 x 870
68.681
75.062
100.000
-/-
VESA, 640 x 480
37.861
72.809
31.500
-/-
VESA, 640 x 480
37.500
75.000
31.500
-/-
VESA, 800 x 600
35.156
56.250
36.000
+/+
VESA, 800 x 600
37.879
60.317
40.000
+/+
VESA, 800 x 600
48.077
72.188
50.000
+/+
VESA, 800 x 600
46.875
75.000
49.500
+/+
VESA, 1024 x 768
48.363
60.004
65.000
-/-
VESA, 1024 x 768
56.476
70.069
75.000
-/-
VESA, 1024 x 768
60.023
75.029
78.750
+/+
VESA, 1152 x 864
67.500
75.000
108.000
+/+
VESA, 1280 X 960
60.000
60.000
108.000
+/+
VESA, 1280 X 1024
63.981
60.020
108.000
+/+
VESA, 1280 X 1024
79.976
75.025
135.000
+/+
VESA, 1280 x 800
49.702
59.810
83.500
-/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the
screen horizontally is called the Horizontal Cycle and the inverse number of
the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times
per second to display an image to the user. The frequency of this repetition is
called the Vertical Frequency or Refresh Rate. Unit: Hz
Specifications
General
General
Model Name
SyncMaster 933BW
LCD Panel
Size
19 inch (48 cm)
Display area
408.24 mm (H) x 255.15 mm (V)
Pixel Pitch
0.2835 mm (H) x 0.2835 mm (V)
Synchronization
Horizontal
30 ~ 81 kHz
Vertical
56 ~ 75 Hz
Display Color
16.7M
Resolution
Optimum resolution
1440 x 900@60 Hz
Maximum resolution
1440 x 900@75 Hz
Input Signal, Terminated
RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
137 MHz (Analog, Digital)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
DVI-D to DVI-D connector, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
451.0 x 331.7 x 72.4 mm / 17.8 x 13.1 x 2.9 inch (Without Stand)
451.0 x 379.3 x 200.0 mm / 17.8 x 14.9 x 7.9 inch (With Stand), 4 kg / 8.82 lbs
VESA Mounting Interface
75 mm x 75 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Storage
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the
computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor
installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth)
above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright
sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas
including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor
to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal
operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or
when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in
your computer. Use the software utility installed on your computer to set up this feature.
State
Normal Operation
Power saving mode
Power off (Power button)
EPA/ENERGY 2000
Power Indicator
On
Blinking
Off
Power Consumption
34 watts
Less than 1 watts
Less than 1 watts
This monitor is EPA ENERGY STAR® compliant and ENERGY 2000 compliant when used with
a computer equipped with VESA DPM functionality.
As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets the
ENERGY STAR® guidelines for energy efficiency.
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted
automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual
and adjusts the screen as follows.
Display Mode
Horizontal
Frequency
(kHz)
Vertical
Frequency (Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
IBM, 720 x 400
31.469
70.087
28.322
-/+
MAC, 640 x 480
35.000
66.667
30.240
-/-
MAC, 832 x 624
49.726
74.551
57.284
-/-
MAC, 1152 x 870
68.681
75.062
100.000
-/-
VESA, 640 x 480
31.469
59.940
25.175
-/-
VESA, 640 x 480
37.861
72.809
31.500
-/-
VESA, 640 x 480
37.500
75.000
31.500
-/-
VESA, 800 x 600
35.156
56.250
36.000
+/+
VESA, 800 x 600
37.879
60.317
40.000
+/+
VESA, 800 x 600
48.077
72.188
50.000
+/+
VESA, 800 x 600
46.875
75.000
49.500
+/+
VESA, 1024 x 768
48.363
60.004
65.000
-/-
VESA, 1024 x 768
56.476
70.069
75.000
-/-
VESA, 1024 x 768
60.023
75.029
78.750
+/+
VESA, 1152 x 864
67.500
75.000
108.000
+/+
VESA, 1280 x 800
49.702
59.810
83.500
+/+
VESA, 1280 X 960
60.000
60.000
108.000
+/+
VESA, 1280 X 1024
63.981
60.020
108.000
+/+
VESA, 1280 X 1024
79.976
75.025
135.000
+/+
VESA, 1440 X 900
55.935
59.887
106.500
-/+
VESA, 1440 X 900
70.635
74.984
136.750
-/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the
screen horizontally is called the Horizontal Cycle and the inverse number of
the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times
per second to display an image to the user. The frequency of this repetition is
called the Vertical Frequency or Refresh Rate. Unit: Hz
Specifications
General
General
Model Name
SyncMaster 933BWPLUS
LCD Panel
Size
19 inch (48 cm)
Display area
408.24 mm (H) x 255.15 mm (V)
Pixel Pitch
0.2835 mm (H) x 0.2835 mm (V)
Synchronization
Horizontal
30 ~ 81 kHz
Vertical
56 ~ 75 Hz
Display Color
16.7M
Resolution
Optimum resolution
1440 x 900@60 Hz
Maximum resolution
1440 x 900@75 Hz
Input Signal, Terminated
RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
137 MHz (Analog, Digital)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
DVI-D to DVI-D connector, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
451.0 x 331.7 x 72.4 mm / 17.8 x 13.1 x 2.9 inch (Without Stand)
451.0 x 379.3 x 200.0 mm / 17.8 x 14.9 x 7.9 inch (With Stand), 4 kg / 8.82 lbs
VESA Mounting Interface
75 mm x 75 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Storage
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the
computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor
installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth)
above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright
sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas
including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor
to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal
operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or
when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in
your computer. Use the software utility installed on your computer to set up this feature.
State
Normal Operation
Power saving mode
Power off (Power button)
EPA/ENERGY 2000
Power Indicator
On
Blinking
Off
Power Consumption
34 watts
Less than 1 watts
Less than 1 watts
This monitor is EPA ENERGY STAR® compliant and ENERGY 2000 compliant when used with
a computer equipped with VESA DPM functionality.
As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets the
ENERGY STAR® guidelines for energy efficiency.
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted
automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual
and adjusts the screen as follows.
Display Mode
Horizontal
Frequency
(kHz)
Vertical
Frequency (Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
IBM, 720 x 400
31.469
70.087
28.322
-/+
MAC, 640 x 480
35.000
66.667
30.240
-/-
MAC, 832 x 624
49.726
74.551
57.284
-/-
MAC, 1152 x 870
68.681
75.062
100.000
-/-
VESA, 640 x 480
31.469
59.940
25.175
-/-
VESA, 640 x 480
37.861
72.809
31.500
-/-
VESA, 640 x 480
37.500
75.000
31.500
-/-
VESA, 800 x 600
35.156
56.250
36.000
+/+
VESA, 800 x 600
37.879
60.317
40.000
+/+
VESA, 800 x 600
48.077
72.188
50.000
+/+
VESA, 800 x 600
46.875
75.000
49.500
+/+
VESA, 1024 x 768
48.363
60.004
65.000
-/-
VESA, 1024 x 768
56.476
70.069
75.000
-/-
VESA, 1024 x 768
60.023
75.029
78.750
+/+
VESA, 1152 x 864
67.500
75.000
108.000
+/+
VESA, 1280 x 800
49.702
59.810
83.500
+/+
VESA, 1280 X 960
60.000
60.000
108.000
+/+
VESA, 1280 X 1024
63.981
60.020
108.000
+/+
VESA, 1280 X 1024
79.976
75.025
135.000
+/+
VESA, 1440 X 900
55.935
59.887
106.500
-/+
VESA, 1440 X 900
70.635
74.984
136.750
-/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the
screen horizontally is called the Horizontal Cycle and the inverse number of
the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times
per second to display an image to the user. The frequency of this repetition is
called the Vertical Frequency or Refresh Rate. Unit: Hz
Specifications
General
General
Model Name
SyncMaster 933GW
LCD Panel
Size
19 inch (48 cm)
Display area
408.24 mm (H) x 255.15 mm (V)
Pixel Pitch
0.2835 mm (H) x 0.2835 mm (V)
Synchronization
Horizontal
30 ~ 81 kHz
Vertical
56 ~ 75 Hz
Display Color
16.7M
Resolution
Optimum resolution
1440 x 900@60 Hz
Maximum resolution
1440 x 900@75 Hz
Input Signal, Terminated
RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
137 MHz (Analog, Digital)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
DVI-D to DVI-D connector, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
451.0 x 331.7 x 72.4 mm / 17.8 x 13.1 x 2.9 inch (Without Stand)
451.0 x 379.3 x 200.0 mm / 17.8 x 14.9 x 7.9 inch (With Stand), 4 kg / 8.82 lbs
VESA Mounting Interface
75 mm x 75 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Storage
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the
computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor
installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth)
above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright
sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas
including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor
to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal
operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or
when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in
your computer. Use the software utility installed on your computer to set up this feature.
State
Normal Operation
Power saving mode
Power off (Power button)
EPA/ENERGY 2000
Power Indicator
On
Blinking
Off
Power Consumption
34 watts
Less than 1 watts
Less than 1 watts
This monitor is EPA ENERGY STAR® compliant and ENERGY 2000 compliant when used with
a computer equipped with VESA DPM functionality.
As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets the
ENERGY STAR® guidelines for energy efficiency.
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted
automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual
and adjusts the screen as follows.
Display Mode
Horizontal
Frequency
(kHz)
Vertical
Frequency (Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
IBM, 720 x 400
31.469
70.087
28.322
-/+
MAC, 640 x 480
35.000
66.667
30.240
-/-
MAC, 832 x 624
49.726
74.551
57.284
-/-
MAC, 1152 x 870
68.681
75.062
100.000
-/-
VESA, 640 x 480
31.469
59.940
25.175
-/-
VESA, 640 x 480
37.861
72.809
31.500
-/-
VESA, 640 x 480
37.500
75.000
31.500
-/-
VESA, 800 x 600
35.156
56.250
36.000
+/+
VESA, 800 x 600
37.879
60.317
40.000
+/+
VESA, 800 x 600
48.077
72.188
50.000
+/+
VESA, 800 x 600
46.875
75.000
49.500
+/+
VESA, 1024 x 768
48.363
60.004
65.000
-/-
VESA, 1024 x 768
56.476
70.069
75.000
-/-
VESA, 1024 x 768
60.023
75.029
78.750
+/+
VESA, 1152 x 864
67.500
75.000
108.000
+/+
VESA, 1280 x 800
49.702
59.810
83.500
+/+
VESA, 1280 X 960
60.000
60.000
108.000
+/+
VESA, 1280 X 1024
63.981
60.020
108.000
+/+
VESA, 1280 X 1024
79.976
75.025
135.000
+/+
VESA, 1440 X 900
55.935
59.887
106.500
-/+
VESA, 1440 X 900
70.635
74.984
136.750
-/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the
screen horizontally is called the Horizontal Cycle and the inverse number of
the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times
per second to display an image to the user. The frequency of this repetition is
called the Vertical Frequency or Refresh Rate. Unit: Hz
Specifications
General
General
Model Name
SyncMaster 933GWPLUS
LCD Panel
Size
19 inch (48 cm)
Display area
408.24 mm (H) x 255.15 mm (V)
Pixel Pitch
0.2835 mm (H) x 0.2835 mm (V)
Synchronization
Horizontal
30 ~ 81 kHz
Vertical
56 ~ 75 Hz
Display Color
16.7M
Resolution
Optimum resolution
1440 x 900@60 Hz
Maximum resolution
1440 x 900@75 Hz
Input Signal, Terminated
RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
137 MHz (Analog, Digital)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
DVI-D to DVI-D connector, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
451.0 x 331.7 x 72.4 mm / 17.8 x 13.1 x 2.9 inch (Without Stand)
451.0 x 379.3 x 200.0 mm / 17.8 x 14.9 x 7.9 inch (With Stand), 4 kg / 8.82 lbs
VESA Mounting Interface
75 mm x 75 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Storage
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the
computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor
installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth)
above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright
sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas
including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor
to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal
operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or
when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in
your computer. Use the software utility installed on your computer to set up this feature.
State
Normal Operation
Power saving mode
Power off (Power button)
EPA/ENERGY 2000
Power Indicator
On
Blinking
Off
Power Consumption
34 watts
Less than 1 watts
Less than 1 watts
This monitor is EPA ENERGY STAR® compliant and ENERGY 2000 compliant when used with
a computer equipped with VESA DPM functionality.
As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets the
ENERGY STAR® guidelines for energy efficiency.
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted
automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual
and adjusts the screen as follows.
Display Mode
Horizontal
Frequency
(kHz)
Vertical
Frequency (Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
IBM, 720 x 400
31.469
70.087
28.322
-/+
MAC, 640 x 480
35.000
66.667
30.240
-/-
MAC, 832 x 624
49.726
74.551
57.284
-/-
MAC, 1152 x 870
68.681
75.062
100.000
-/-
VESA, 640 x 480
31.469
59.940
25.175
-/-
VESA, 640 x 480
37.861
72.809
31.500
-/-
VESA, 640 x 480
37.500
75.000
31.500
-/-
VESA, 800 x 600
35.156
56.250
36.000
+/+
VESA, 800 x 600
37.879
60.317
40.000
+/+
VESA, 800 x 600
48.077
72.188
50.000
+/+
VESA, 800 x 600
46.875
75.000
49.500
+/+
VESA, 1024 x 768
48.363
60.004
65.000
-/-
VESA, 1024 x 768
56.476
70.069
75.000
-/-
VESA, 1024 x 768
60.023
75.029
78.750
+/+
VESA, 1152 x 864
67.500
75.000
108.000
+/+
VESA, 1280 x 800
49.702
59.810
83.500
+/+
VESA, 1280 X 960
60.000
60.000
108.000
+/+
VESA, 1280 X 1024
63.981
60.020
108.000
+/+
VESA, 1280 X 1024
79.976
75.025
135.000
+/+
VESA, 1440 X 900
55.935
59.887
106.500
-/+
VESA, 1440 X 900
70.635
74.984
136.750
-/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the
screen horizontally is called the Horizontal Cycle and the inverse number of
the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times
per second to display an image to the user. The frequency of this repetition is
called the Vertical Frequency or Refresh Rate. Unit: Hz
Specifications
General
General
Model Name
SyncMaster 933NW
LCD Panel
Size
19 inch (48 cm)
Display area
408.24 mm (H) x 255.15 mm (V)
Pixel Pitch
0.2835 mm (H) x 0.2835 mm (V)
Synchronization
Horizontal
30 ~ 81 kHz
Vertical
56 ~ 75 Hz
Display Color
16.7M
Resolution
Optimum resolution
1440 x 900@60 Hz
Maximum resolution
1440 x 900@75 Hz
Input Signal, Terminated
RGB Analog
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
137 MHz
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
451.0 x 331.7 x 72.4 mm / 17.8 x 13.1 x 2.9 inch (Without Stand)
451.0 x 379.3 x 200.0 mm / 17.8 x 14.9 x 7.9 inch (With Stand), 4 kg / 10.7 lbs
VESA Mounting Interface
75.0 mm x 75.0 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Storage
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the
computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor
installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth)
above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright
sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas
including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor
to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal
operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or
when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in
your computer. Use the software utility installed on your computer to set up this feature.
State
Normal Operation
Power saving mode
Power off (Power button)
EPA/ENERGY 2000
Power Indicator
ON
Blinking
Off
Power Consumption
34 watts
Less than 1 watts
Less than 1 watts
This monitor is EPA ENERGY STAR® compliant and ENERGY2000 compliant when used with
a computer equipped with VESA DPM functionality.
As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets the
ENERGY STAR® guidelines for energy efficiency.
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted
automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual
and adjusts the screen as follows.
Display Mode
Horizontal
Frequency
(kHz)
Vertical
Frequency (Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
IBM, 720 x 400
31.469
70.087
28.322
-/+
MAC, 640 x 480
35.000
66.667
30.240
-/-
MAC, 832 x 624
49.726
74.551
57.284
-/-
MAC, 1152 x 870
68.681
75.062
100.000
-/-
VESA, 640 x 480
31.469
59.940
25.175
-/-
VESA, 640 x 480
37.861
72.809
31.500
-/-
VESA, 640 x 480
37.500
75.000
31.500
-/-
VESA, 800 x 600
35.156
56.250
36.000
+/+
VESA, 800 x 600
37.879
60.317
40.000
+/+
VESA, 800 x 600
48.077
72.188
50.000
+/+
VESA, 800 x 600
46.875
75.000
49.500
+/+
VESA, 1024 x 768
48.363
60.004
65.000
-/-
VESA, 1024 x 768
56.476
70.069
75.000
-/-
VESA, 1024 x 768
60.023
75.029
78.750
+/+
VESA, 1152 x 864
67.500
75.000
108.000
+/+
VESA, 1280 x 800
49.702
59.810
83.500
+/+
VESA, 1280 X 960
60.000
60.000
108.000
+/+
VESA, 1280 X 1024
63.981
60.020
108.000
+/+
VESA, 1280 X 1024
79.976
75.025
135.000
+/+
VESA, 1440 X 900
55.935
59.887
106.500
-/+
VESA, 1440 X 900
70.635
74.984
136.750
-/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the
screen horizontally is called the Horizontal Cycle and the inverse number of
the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times
per second to display an image to the user. The frequency of this repetition is
called the Vertical Frequency or Refresh Rate. Unit: Hz
Specifications
General
General
Model Name
SyncMaster 933NWPLUS
LCD Panel
Size
19 inch (48 cm)
Display area
408.24 mm (H) x 255.15 mm (V)
Pixel Pitch
0.2835 mm (H) x 0.2835 mm (V)
Synchronization
Horizontal
30 ~ 81 kHz
Vertical
56 ~ 75 Hz
Display Color
16.7M
Resolution
Optimum resolution
1440 x 900@60 Hz
Maximum resolution
1440 x 900@75 Hz
Input Signal, Terminated
RGB Analog
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
137 MHz
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
451.0 x 331.7 x 72.4 mm / 17.8 x 13.1 x 2.9 inch (Without Stand)
451.0 x 379.3 x 200.0 mm / 17.8 x 14.9 x 7.9 inch (With Stand), 4 kg / 10.7 lbs
VESA Mounting Interface
75.0 mm x 75.0 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Storage
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the
computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor
installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth)
above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright
sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas
including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor
to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal
operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or
when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in
your computer. Use the software utility installed on your computer to set up this feature.
State
Normal Operation
Power saving mode
Power off (Power button)
EPA/ENERGY 2000
Power Indicator
ON
Blinking
Off
Power Consumption
34 watts
Less than 1 watts
Less than 1 watts
This monitor is EPA ENERGY STAR® compliant and ENERGY2000 compliant when used with
a computer equipped with VESA DPM functionality.
As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets the
ENERGY STAR® guidelines for energy efficiency.
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted
automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual
and adjusts the screen as follows.
Display Mode
Horizontal
Frequency
(kHz)
Vertical
Frequency (Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
IBM, 720 x 400
31.469
70.087
28.322
-/+
MAC, 640 x 480
35.000
66.667
30.240
-/-
MAC, 832 x 624
49.726
74.551
57.284
-/-
MAC, 1152 x 870
68.681
75.062
100.000
-/-
VESA, 640 x 480
31.469
59.940
25.175
-/-
VESA, 640 x 480
37.861
72.809
31.500
-/-
VESA, 640 x 480
37.500
75.000
31.500
-/-
VESA, 800 x 600
35.156
56.250
36.000
+/+
VESA, 800 x 600
37.879
60.317
40.000
+/+
VESA, 800 x 600
48.077
72.188
50.000
+/+
VESA, 800 x 600
46.875
75.000
49.500
+/+
VESA, 1024 x 768
48.363
60.004
65.000
-/-
VESA, 1024 x 768
56.476
70.069
75.000
-/-
VESA, 1024 x 768
60.023
75.029
78.750
+/+
VESA, 1152 x 864
67.500
75.000
108.000
+/+
VESA, 1280 x 800
49.702
59.810
83.500
+/+
VESA, 1280 X 960
60.000
60.000
108.000
+/+
VESA, 1280 X 1024
63.981
60.020
108.000
+/+
VESA, 1280 X 1024
79.976
75.025
135.000
+/+
VESA, 1440 X 900
55.935
59.887
106.500
-/+
VESA, 1440 X 900
70.635
74.984
136.750
-/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the
screen horizontally is called the Horizontal Cycle and the inverse number of
the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times
per second to display an image to the user. The frequency of this repetition is
called the Vertical Frequency or Refresh Rate. Unit: Hz
Specifications
General
General
Model Name
SyncMaster 933SN
LCD Panel
Size
18.5 inch (47 cm)
Display area
409.8 mm (H) x 230.4 mm (V)
Pixel Pitch
0.3 mm (H) x 0.3 mm (V)
Synchronization
Horizontal
31 ~ 80 kHz
Vertical
56 ~ 75 Hz
Display Color
16.7M
Resolution
Optimum resolution
1360 x 768@60 Hz
Maximum resolution
1360 x 768@60 Hz
Input Signal, Terminated
RGB Analog
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
89 MHz
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
453.3 x 299.3x 69.8 mm / 17.9 x 11.8x 2.8inch (Without Stand)
453.3 x 354.9 x 176.6 mm / 17.9 x13.9 x 6.9 inch (With Stand), 3.65 kg / 9.8 lbs
VESA Mounting Interface
75.0 mm x 75.0 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Storage
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the
computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor
installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth)
above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright
sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas
including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor
to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal
operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or
when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in
your computer. Use the software utility installed on your computer to set up this feature.
State
Normal Operation
Power saving mode
Power off (Power button)
EPA/ENERGY 2000
Power Indicator
ON
Blinking
Off
Power Consumption
18 watts
Less than 1 watts
Less than 1 watts
This monitor is EPA ENERGY STAR® compliant and ENERGY2000 compliant when used with
a computer equipped with VESA DPM functionality.
As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets the
ENERGY STAR® guidelines for energy efficiency.
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted
automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual
and adjusts the screen as follows.
Display Mode
Horizontal
Frequency
(kHz)
Vertical
Frequency (Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
IBM, 720 x 400
31.469
70.087
28.322
-/+
MAC, 640 x 480
35.000
66.667
30.240
-/-
MAC, 832 x 624
49.726
74.551
57.284
-/-
VESA, 640 x 480
37.861
72.809
31.500
-/-
VESA, 640 x 480
37.500
75.000
31.500
-/-
VESA, 800 x 600
35.156
56.250
36.000
+/+
VESA, 800 x 600
37.879
60.317
40.000
+/+
VESA, 800 x 600
48.077
72.188
50.000
+/+
VESA, 800 x 600
46.875
75.000
49.500
+/+
VESA, 1024 x 768
48.363
60.004
65.000
-/-
VESA, 1024 x 768
56.476
70.069
75.000
-/-
VESA, 1024 x 768
60.023
75.029
78.750
+/+
VESA, 1360 X 768
47.712
60.000
85.500
+/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the
screen horizontally is called the Horizontal Cycle and the inverse number of
the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times
per second to display an image to the user. The frequency of this repetition is
called the Vertical Frequency or Refresh Rate. Unit: Hz
Specifications
General
General
Model Name
SyncMaster 933SNPLUS
LCD Panel
Size
18.5 inch (47 cm)
Display area
409.8 mm (H) x 230.4 mm (V)
Pixel Pitch
0.3 mm (H) x 0.3 mm (V)
Synchronization
Horizontal
31 ~ 80 kHz
Vertical
56 ~ 75 Hz
Display Color
16.7M
Resolution
Optimum resolution
1360 x 768@60 Hz
Maximum resolution
1360 x 768@60 Hz
Input Signal, Terminated
RGB Analog
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
89 MHz
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
453.3 x 299.3x 69.8 mm / 17.9 x 11.8x 2.8inch (Without Stand)
453.3 x 354.9 x 176.6 mm / 17.9 x13.9 x 6.9 inch (With Stand), 3.65 kg / 9.8 lbs
VESA Mounting Interface
75.0 mm x 75.0 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Storage
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the
computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor
installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth)
above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright
sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas
including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor
to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal
operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or
when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in
your computer. Use the software utility installed on your computer to set up this feature.
State
Normal Operation
Power saving mode
Power off (Power button)
EPA/ENERGY 2000
Power Indicator
ON
Blinking
Off
Power Consumption
18 watts
Less than 1 watts
Less than 1 watts
This monitor is EPA ENERGY STAR® compliant and ENERGY2000 compliant when used with
a computer equipped with VESA DPM functionality.
As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets the
ENERGY STAR® guidelines for energy efficiency.
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted
automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual
and adjusts the screen as follows.
Display Mode
Horizontal
Frequency
(kHz)
Vertical
Frequency (Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
IBM, 720 x 400
31.469
70.087
28.322
-/+
MAC, 640 x 480
35.000
66.667
30.240
-/-
MAC, 832 x 624
49.726
74.551
57.284
-/-
VESA, 640 x 480
37.861
72.809
31.500
-/-
VESA, 640 x 480
37.500
75.000
31.500
-/-
VESA, 800 x 600
35.156
56.250
36.000
+/+
VESA, 800 x 600
37.879
60.317
40.000
+/+
VESA, 800 x 600
48.077
72.188
50.000
+/+
VESA, 800 x 600
46.875
75.000
49.500
+/+
VESA, 1024 x 768
48.363
60.004
65.000
-/-
VESA, 1024 x 768
56.476
70.069
75.000
-/-
VESA, 1024 x 768
60.023
75.029
78.750
+/+
VESA, 1360 X 768
47.712
60.000
85.500
+/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the
screen horizontally is called the Horizontal Cycle and the inverse number of
the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times
per second to display an image to the user. The frequency of this repetition is
called the Vertical Frequency or Refresh Rate. Unit: Hz
Specifications
General
General
Model Name
SyncMaster 2033SN
LCD Panel
Size
20.0 inch (50 cm)
Display area
442.8 mm (H) x 249.075 mm (V)
Pixel Pitch
0.2768 mm (H) x 0.2768 mm (V)
Synchronization
Horizontal
30 ~ 81kHz
Vertical
56 ~ 75 Hz
Display Color
16.7M
Resolution
Optimum resolution
1600 x 900@60 Hz
Maximum resolution
1600 x 900@60 Hz
Input Signal, Terminated
RGB Analog,
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
150 MHz (Analog)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
485.8 x 325.9 x 72.6 mm(19.1 x 12.8 x 2.9 inch) (Without Stand)
485.8 x 373.5 x 200 mm (19.1 x 14.7 x 7.9 inch) (With Stand) / 4.45 kg(9.8 lbs)
VESA Mounting Interface
100 mm x 100 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Storage
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the
computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor
installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth)
above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright
sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas
including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor
to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal
operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or
when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in
your computer. Use the software utility installed on your computer to set up this feature.
State
Normal Operation
Power saving mode
Power off (Power button)
EPA/ENERGY 2000
Power Indicator
On
Blinking
Off
Power Consumption
40 watts
Less than 1 watts
Less than 1 watts
This monitor is EPA ENERGY STAR® compliant and ENERG Y2000 compliant when used with
a computer equipped with VESA DPM functionality.
As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets the
ENERGY STAR® guidelines for energy efficiency.
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted
automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual
and adjusts the screen as follows.
Display Mode
Horizontal
Frequency
(kHz)
Vertical
Frequency (Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
IBM, 720 x 400
31.469
70.087
28.322
-/+
MAC, 640 x 480
35.000
66.667
30.240
-/-
MAC, 832 x 624
49.726
74.551
57.284
-/-
MAC, 1152 x 870
68.681
75.062
100.000
-/-
VESA, 640 x 480
31.469
59.940
25.175
-/-
VESA, 640 x 480
37.861
72.809
31.500
-/-
VESA, 640 x 480
37.500
75.000
31.500
-/-
VESA, 800 x 600
35.156
56.250
36.000
+/+
VESA, 800 x 600
37.879
60.317
40.000
+/+
VESA, 800 x 600
48.077
72.188
50.000
+/+
VESA, 800 x 600
46.875
75.000
49.500
+/+
VESA, 1024 x 768
48.363
60.004
65.000
-/-
VESA, 1024 x 768
56.476
70.069
75.000
-/-
VESA, 1024 x 768
60.023
75.029
78.750
+/+
VESA, 1152 x 864
67.500
75.000
108.000
+/+
VESA, 1280 x 800
49.702
59.810
83.50
-/+
VESA, 1280 x 800
62.795
74.934
106.500
-/+
VESA, 1440 x 900
55.935
59.887
106.500
-/+
VESA, 1440 x 900
70.635
74.984
136.750
-/+
VESA, 1600 x 900
60.000
60.000
108.000
+/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the
screen horizontally is called the Horizontal Cycle and the inverse number of
the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times
per second to display an image to the user. The frequency of this repetition is
called the Vertical Frequency or Refresh Rate. Unit: Hz
Specifications
General
General
Model Name
SyncMaster 2033SNPLUS
LCD Panel
Size
20.0 inch (50 cm)
Display area
442.8 mm (H) x 249.075 mm (V)
Pixel Pitch
0.2768 mm (H) x 0.2768 mm (V)
Synchronization
Horizontal
30 ~ 81kHz
Vertical
56 ~ 75 Hz
Display Color
16.7M
Resolution
Optimum resolution
1600 x 900@60 Hz
Maximum resolution
1600 x 900@60 Hz
Input Signal, Terminated
RGB Analog,
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
150 MHz (Analog)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
485.8 x 325.9 x 72.6 mm(19.1 x 12.8 x 2.9 inch) (Without Stand)
485.8 x 373.5 x 200 mm (19.1 x 14.7 x 7.9 inch) (With Stand) / 4.45 kg(9.8 lbs)
VESA Mounting Interface
100 mm x 100 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Storage
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the
computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor
installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth)
above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright
sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas
including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor
to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal
operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or
when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in
your computer. Use the software utility installed on your computer to set up this feature.
State
Normal Operation
Power saving mode
Power off (Power button)
EPA/ENERGY 2000
Power Indicator
On
Blinking
Off
Power Consumption
40 watts
Less than 1 watts
Less than 1 watts
This monitor is EPA ENERGY STAR® compliant and ENERG Y2000 compliant when used with
a computer equipped with VESA DPM functionality.
As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets the
ENERGY STAR® guidelines for energy efficiency.
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted
automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual
and adjusts the screen as follows.
Display Mode
Horizontal
Frequency
(kHz)
Vertical
Frequency (Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
IBM, 720 x 400
31.469
70.087
28.322
-/+
MAC, 640 x 480
35.000
66.667
30.240
-/-
MAC, 832 x 624
49.726
74.551
57.284
-/-
MAC, 1152 x 870
68.681
75.062
100.000
-/-
VESA, 640 x 480
31.469
59.940
25.175
-/-
VESA, 640 x 480
37.861
72.809
31.500
-/-
VESA, 640 x 480
37.500
75.000
31.500
-/-
VESA, 800 x 600
35.156
56.250
36.000
+/+
VESA, 800 x 600
37.879
60.317
40.000
+/+
VESA, 800 x 600
48.077
72.188
50.000
+/+
VESA, 800 x 600
46.875
75.000
49.500
+/+
VESA, 1024 x 768
48.363
60.004
65.000
-/-
VESA, 1024 x 768
56.476
70.069
75.000
-/-
VESA, 1024 x 768
60.023
75.029
78.750
+/+
VESA, 1152 x 864
67.500
75.000
108.000
+/+
VESA, 1280 x 800
49.702
59.810
83.50
-/+
VESA, 1280 x 800
62.795
74.934
106.500
-/+
VESA, 1440 x 900
55.935
59.887
106.500
-/+
VESA, 1440 x 900
70.635
74.984
136.750
-/+
VESA, 1600 x 900
60.000
60.000
108.000
+/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the
screen horizontally is called the Horizontal Cycle and the inverse number of
the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times
per second to display an image to the user. The frequency of this repetition is
called the Vertical Frequency or Refresh Rate. Unit: Hz
Specifications
General
General
Model Name
SyncMaster 2033SW
LCD Panel
Size
20 inch (50 cm)
Display area
442.8 mm (H) x 249.075 mm (V)
Pixel Pitch
0.2768 mm (H) x 0.2768 mm (V)
Synchronization
Horizontal
30 ~ 81 kHz
Vertical
56 ~ 75 Hz
Display Color
16.7M
Resolution
Optimum resolution
1600 x 900@60 Hz
Maximum resolution
1600 x 900@60 Hz
Input Signal, Terminated
RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
150 MHz (Analog, Digital)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable, 1.5m
DVI-D to DVI-D connector, Detachable, 1.5m
Dimensions (W x H x D) / Weight (Simple Stand)
485.8 x 325.9 x 72.6 mm (19.1 x 12.8 x 2.9 inch) (Without Stand)
485.8 x 373.5 x 200 mm (19.1 x 14.7 x 7.9 inch) (With Stand) / 4.45 kg(9.8 lbs)
VESA Mounting Interface
100 mm x 100 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Storage
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the
computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor
installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth)
above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright
sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas
including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor
to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal
operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or
when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in
your computer. Use the software utility installed on your computer to set up this feature.
State
Normal Operation
Power saving mode
Power off (Power button)
EPA/ENERGY 2000
Power Indicator
On
Blinking
Off
Power Consumption
40 watts
Less than 1 watts
Less than 1 watts
This monitor is EPA ENERGY STAR® compliant and ENERGY 2000 compliant when used with
a computer equipped with VESA DPM functionality.
As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets the
ENERGY STAR® guidelines for energy efficiency.
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted
automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual
and adjusts the screen as follows.
Display Mode
Horizontal
Frequency
(kHz)
Vertical
Frequency (Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
IBM, 720 x 400
31.469
70.087
28.322
-/+
MAC, 640 x 480
35.000
66.667
30.240
-/-
MAC, 832 x 624
49.726
74.551
57.284
-/-
MAC, 1152 x 870
68.681
75.062
100.000
-/-
VESA, 640 x 480
31.469
59.940
25.175
-/-
VESA, 640 x 480
37.861
72.809
31.500
-/-
VESA, 640 x 480
37.500
75.000
31.500
-/-
VESA, 800 x 600
35.156
56.250
36.000
+/+
VESA, 800 x 600
37.879
60.317
40.000
+/+
VESA, 800 x 600
48.077
72.188
50.000
+/+
VESA, 800 x 600
46.875
75.000
49.500
+/+
VESA, 1024 x 768
48.363
60.004
65.000
-/-
VESA, 1024 x 768
56.476
70.069
75.000
-/-
VESA, 1024 x 768
60.023
75.029
78.750
+/+
VESA, 1152 x 864
67.500
75.000
108.000
+/+
VESA, 1280 x 800
49.702
59.810
83.50
-/+
VESA, 1280 x 800
62.795
74.934
106.500
-/+
VESA, 1440 x 900
55.935
59.887
106.500
-/+
VESA, 1440 x 900
70.635
74.984
136.750
-/+
VESA, 1600 x 900
60.000
60.000
108.000
+/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the
screen horizontally is called the Horizontal Cycle and the inverse number of
the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times
per second to display an image to the user. The frequency of this repetition is
called the Vertical Frequency or Refresh Rate. Unit: Hz
Specifications
General
General
Model Name
SyncMaster 2033SWPLUS
LCD Panel
Size
20 inch (50 cm)
Display area
442.8 mm (H) x 249.075 mm (V)
Pixel Pitch
0.2768 mm (H) x 0.2768 mm (V)
Synchronization
Horizontal
30 ~ 81 kHz
Vertical
56 ~ 75 Hz
Display Color
16.7M
Resolution
Optimum resolution
1600 x 900@60 Hz
Maximum resolution
1600 x 900@60 Hz
Input Signal, Terminated
RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
150 MHz (Analog, Digital)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable, 1.5m
DVI-D to DVI-D connector, Detachable, 1.5m
Dimensions (W x H x D) / Weight (Simple Stand)
485.8 x 325.9 x 72.6 mm (19.1 x 12.8 x 2.9 inch) (Without Stand)
485.8 x 373.5 x 200 mm (19.1 x 14.7 x 7.9 inch) (With Stand) / 4.45 kg(9.8 lbs)
VESA Mounting Interface
100 mm x 100 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Storage
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the
computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor
installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth)
above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright
sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas
including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor
to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal
operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or
when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in
your computer. Use the software utility installed on your computer to set up this feature.
State
Normal Operation
Power saving mode
Power off (Power button)
EPA/ENERGY 2000
Power Indicator
On
Blinking
Off
Power Consumption
40 watts
Less than 1 watts
Less than 1 watts
This monitor is EPA ENERGY STAR® compliant and ENERGY 2000 compliant when used with
a computer equipped with VESA DPM functionality.
As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets the
ENERGY STAR® guidelines for energy efficiency.
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted
automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual
and adjusts the screen as follows.
Display Mode
Horizontal
Frequency
(kHz)
Vertical
Frequency (Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
IBM, 720 x 400
31.469
70.087
28.322
-/+
MAC, 640 x 480
35.000
66.667
30.240
-/-
MAC, 832 x 624
49.726
74.551
57.284
-/-
MAC, 1152 x 870
68.681
75.062
100.000
-/-
VESA, 640 x 480
31.469
59.940
25.175
-/-
VESA, 640 x 480
37.861
72.809
31.500
-/-
VESA, 640 x 480
37.500
75.000
31.500
-/-
VESA, 800 x 600
35.156
56.250
36.000
+/+
VESA, 800 x 600
37.879
60.317
40.000
+/+
VESA, 800 x 600
48.077
72.188
50.000
+/+
VESA, 800 x 600
46.875
75.000
49.500
+/+
VESA, 1024 x 768
48.363
60.004
65.000
-/-
VESA, 1024 x 768
56.476
70.069
75.000
-/-
VESA, 1024 x 768
60.023
75.029
78.750
+/+
VESA, 1152 x 864
67.500
75.000
108.000
+/+
VESA, 1280 x 800
49.702
59.810
83.50
-/+
VESA, 1280 x 800
62.795
74.934
106.500
-/+
VESA, 1440 x 900
55.935
59.887
106.500
-/+
VESA, 1440 x 900
70.635
74.984
136.750
-/+
VESA, 1600 x 900
60.000
60.000
108.000
+/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the
screen horizontally is called the Horizontal Cycle and the inverse number of
the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times
per second to display an image to the user. The frequency of this repetition is
called the Vertical Frequency or Refresh Rate. Unit: Hz
Specifications
General
General
Model Name
SyncMaster 2233BW
LCD Panel
Size
22 inch (55 cm)
Display area
473.76 mm (H) x 296.1 mm (V)
Pixel Pitch
0.282 mm (H) x 0.282 mm (V)
Synchronization
Horizontal
30 ~ 81 kHz
Vertical
56 ~ 75 Hz
Display Color
16.7M
Resolution
Optimum resolution
1680 x 1050@60 Hz
Maximum resolution
1680 x 1050@60 Hz
Input Signal, Terminated
RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
146 MHz (Analog, Digital)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
DVI-D to DVI-D connector, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
516.8 x 372.7 x 71.2 mm / 20.3 x 14.7 x 2.8 inch (Without Stand)
516.8 x 421.3 x 208.7 mm / 20.3 x 16.6 x 8.2 inch (With Stand), 4.7 kg / 10.4 lbs
VESA Mounting Interface
100 mm x 100 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Storage
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the
computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor
installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth)
above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright
sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas
including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor
to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal
operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or
when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in
your computer. Use the software utility installed on your computer to set up this feature.
State
Normal Operation
Power saving mode
Power off (Power button)
EPA/ENERGY 2000
Power Indicator
On
Blinking
Off
Power Consumption
45 watts
Less than 1 watts
Less than 1 watts
This monitor is EPA ENERGY STAR® compliant and ENERGY 2000 compliant when used with
a computer equipped with VESA DPM functionality.
As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets the
ENERGY STAR® guidelines for energy efficiency.
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted
automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual
and adjusts the screen as follows.
Display Mode
Horizontal
Frequency
(kHz)
Vertical
Frequency (Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
IBM, 720 x 400
31.469
70.087
28.322
-/+
MAC, 640 x 480
35.000
66.667
30.240
-/-
MAC, 832 x 624
49.726
74.551
57.284
-/-
MAC, 1152 x 870
68.681
75.062
100.000
-/-
VESA, 640 x 480
31.469
59.94
25.175
-/-
VESA, 640 x 480
37.861
72.809
31.500
-/-
VESA, 640 x 480
37.500
75.000
31.500
-/-
VESA, 800 x 600
35.156
56.250
36.000
+/+
VESA, 800 x 600
37.879
60.317
40.000
+/+
VESA, 800 x 600
48.077
72.188
50.000
+/+
VESA, 800 x 600
46.875
75.000
49.500
+/+
VESA, 1024 x 768
48.363
60.004
65.000
-/-
VESA, 1024 x 768
56.476
70.069
75.000
-/-
VESA, 1024 x 768
60.023
75.029
78.750
+/+
VESA, 1152 x 864
67.500
75.000
108.000
+/+
VESA, 1280 x 800
49.702
59.810
83.500
-/+
VESA, 1280 x 960
60.000
60.000
108.000
+/+
VESA, 1280 x 1024
63.981
60.020
108.000
+/+
VESA, 1280 x 1024
79.976
75.025
135.000
+/+
VESA, 1440 x 900
55.935
59.887
106.500
-/+
VESA, 1440 x 900
70.635
74.984
136.750
-/+
VESA, 1680 x 1050
65.290
59.954
146.250
-/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the
screen horizontally is called the Horizontal Cycle and the inverse number of
the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times
per second to display an image to the user. The frequency of this repetition is
called the Vertical Frequency or Refresh Rate. Unit: Hz
Specifications
General
General
Model Name
SyncMaster 2233BWPLUS
LCD Panel
Size
22 inch (55 cm)
Display area
473.76 mm (H) x 296.1 mm (V)
Pixel Pitch
0.282 mm (H) x 0.282 mm (V)
Synchronization
Horizontal
30 ~ 81 kHz
Vertical
56 ~ 75 Hz
Display Color
16.7M
Resolution
Optimum resolution
1680 x 1050@60 Hz
Maximum resolution
1680 x 1050@60 Hz
Input Signal, Terminated
RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
146 MHz (Analog, Digital)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
DVI-D to DVI-D connector, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
516.8 x 372.7 x 71.2 mm / 20.3 x 14.7 x 2.8 inch (Without Stand)
516.8 x 421.3 x 208.7 mm / 20.3 x 16.6 x 8.2 inch (With Stand), 4.7 kg / 10.4 lbs
VESA Mounting Interface
100 mm x 100 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Storage
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the
computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor
installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth)
above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright
sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas
including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor
to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal
operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or
when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in
your computer. Use the software utility installed on your computer to set up this feature.
State
Normal Operation
Power saving mode
Power off (Power button)
EPA/ENERGY 2000
Power Indicator
On
Blinking
Off
Power Consumption
45 watts
Less than 1 watts
Less than 1 watts
This monitor is EPA ENERGY STAR® compliant and ENERGY 2000 compliant when used with
a computer equipped with VESA DPM functionality.
As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets the
ENERGY STAR® guidelines for energy efficiency.
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted
automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual
and adjusts the screen as follows.
Display Mode
Horizontal
Frequency
(kHz)
Vertical
Frequency (Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
IBM, 720 x 400
31.469
70.087
28.322
-/+
MAC, 640 x 480
35.000
66.667
30.240
-/-
MAC, 832 x 624
49.726
74.551
57.284
-/-
MAC, 1152 x 870
68.681
75.062
100.000
-/-
VESA, 640 x 480
31.469
59.94
25.175
-/-
VESA, 640 x 480
37.861
72.809
31.500
-/-
VESA, 640 x 480
37.500
75.000
31.500
-/-
VESA, 800 x 600
35.156
56.250
36.000
+/+
VESA, 800 x 600
37.879
60.317
40.000
+/+
VESA, 800 x 600
48.077
72.188
50.000
+/+
VESA, 800 x 600
46.875
75.000
49.500
+/+
VESA, 1024 x 768
48.363
60.004
65.000
-/-
VESA, 1024 x 768
56.476
70.069
75.000
-/-
VESA, 1024 x 768
60.023
75.029
78.750
+/+
VESA, 1152 x 864
67.500
75.000
108.000
+/+
VESA, 1280 x 800
49.702
59.810
83.500
-/+
VESA, 1280 x 960
60.000
60.000
108.000
+/+
VESA, 1280 x 1024
63.981
60.020
108.000
+/+
VESA, 1280 x 1024
79.976
75.025
135.000
+/+
VESA, 1440 x 900
55.935
59.887
106.500
-/+
VESA, 1440 x 900
70.635
74.984
136.750
-/+
VESA, 1680 x 1050
65.290
59.954
146.250
-/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the
screen horizontally is called the Horizontal Cycle and the inverse number of
the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times
per second to display an image to the user. The frequency of this repetition is
called the Vertical Frequency or Refresh Rate. Unit: Hz
Specifications
General
General
Model Name
SyncMaster 2233GW
LCD Panel
Size
22 inch (55 cm)
Display area
473.76 mm (H) x 296.1 mm (V)
Pixel Pitch
0.282 mm (H) x 0.282 mm (V)
Synchronization
Horizontal
30 ~ 81 kHz
Vertical
56 ~ 75 Hz
Display Color
16.7M
Resolution
Optimum resolution
1680 x 1050@60 Hz
Maximum resolution
1680 x 1050@60 Hz
Input Signal, Terminated
RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
146 MHz (Analog, Digital)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
DVI-D to DVI-D connector, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
516.8 x 372.7 x 71.2 mm / 20.3 x 14.7 x 2.8 inch (Without Stand)
516.8 x 421.3 x 208.7 mm / 20.3 x 16.6 x 8.2 inch (With Stand), 4.7 kg / 10.4 lbs
VESA Mounting Interface
100 mm x 100 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Storage
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the
computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor
installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth)
above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright
sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas
including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor
to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal
operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or
when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in
your computer. Use the software utility installed on your computer to set up this feature.
State
Normal Operation
Power saving mode
Power off (Power button)
EPA/ENERGY 2000
Power Indicator
On
Blinking
Off
Power Consumption
45 watts
Less than 1 watts
Less than 1 watts
This monitor is EPA ENERGY STAR® compliant and ENERGY 2000 compliant when used with
a computer equipped with VESA DPM functionality.
As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets the
ENERGY STAR® guidelines for energy efficiency.
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted
automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual
and adjusts the screen as follows.
Display Mode
Horizontal
Frequency
(kHz)
Vertical
Frequency (Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
IBM, 720 x 400
31.469
70.087
28.322
-/+
MAC, 640 x 480
35.000
66.667
30.240
-/-
MAC, 832 x 624
49.726
74.551
57.284
-/-
MAC, 1152 x 870
68.681
75.062
100.000
-/-
VESA, 640 x 480
31.469
59.94
25.175
-/-
VESA, 640 x 480
37.861
72.809
31.500
-/-
VESA, 640 x 480
37.500
75.000
31.500
-/-
VESA, 800 x 600
35.156
56.250
36.000
+/+
VESA, 800 x 600
37.879
60.317
40.000
+/+
VESA, 800 x 600
48.077
72.188
50.000
+/+
VESA, 800 x 600
46.875
75.000
49.500
+/+
VESA, 1024 x 768
48.363
60.004
65.000
-/-
VESA, 1024 x 768
56.476
70.069
75.000
-/-
VESA, 1024 x 768
60.023
75.029
78.750
+/+
VESA, 1152 x 864
67.500
75.000
108.000
+/+
VESA, 1280 x 800
49.702
59.810
83.500
-/+
VESA, 1280 x 960
60.000
60.000
108.000
+/+
VESA, 1280 x 1024
63.981
60.020
108.000
+/+
VESA, 1280 x 1024
79.976
75.025
135.000
+/+
VESA, 1440 x 900
55.935
59.887
106.500
-/+
VESA, 1440 x 900
70.635
74.984
136.750
-/+
VESA, 1680 x 1050
65.290
59.954
146.250
-/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the
screen horizontally is called the Horizontal Cycle and the inverse number of
the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times
per second to display an image to the user. The frequency of this repetition is
called the Vertical Frequency or Refresh Rate. Unit: Hz
Specifications
General
General
Model Name
SyncMaster 2233GWPLUS
LCD Panel
Size
22 inch (55 cm)
Display area
473.76 mm (H) x 296.1 mm (V)
Pixel Pitch
0.282 mm (H) x 0.282 mm (V)
Synchronization
Horizontal
30 ~ 81 kHz
Vertical
56 ~ 75 Hz
Display Color
16.7M
Resolution
Optimum resolution
1680 x 1050@60 Hz
Maximum resolution
1680 x 1050@60 Hz
Input Signal, Terminated
RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
146 MHz (Analog, Digital)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
DVI-D to DVI-D connector, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
516.8 x 372.7 x 71.2 mm / 20.3 x 14.7 x 2.8 inch (Without Stand)
516.8 x 421.3 x 208.7 mm / 20.3 x 16.6 x 8.2 inch (With Stand), 4.7 kg / 10.4 lbs
VESA Mounting Interface
100 mm x 100 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Storage
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the
computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor
installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth)
above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright
sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas
including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor
to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal
operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or
when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in
your computer. Use the software utility installed on your computer to set up this feature.
State
Normal Operation
Power saving mode
Power off (Power button)
EPA/ENERGY 2000
Power Indicator
On
Blinking
Off
Power Consumption
45 watts
Less than 1 watts
Less than 1 watts
This monitor is EPA ENERGY STAR® compliant and ENERGY 2000 compliant when used with
a computer equipped with VESA DPM functionality.
As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets the
ENERGY STAR® guidelines for energy efficiency.
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted
automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual
and adjusts the screen as follows.
Display Mode
Horizontal
Frequency
(kHz)
Vertical
Frequency (Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
IBM, 720 x 400
31.469
70.087
28.322
-/+
MAC, 640 x 480
35.000
66.667
30.240
-/-
MAC, 832 x 624
49.726
74.551
57.284
-/-
MAC, 1152 x 870
68.681
75.062
100.000
-/-
VESA, 640 x 480
31.469
59.94
25.175
-/-
VESA, 640 x 480
37.861
72.809
31.500
-/-
VESA, 640 x 480
37.500
75.000
31.500
-/-
VESA, 800 x 600
35.156
56.250
36.000
+/+
VESA, 800 x 600
37.879
60.317
40.000
+/+
VESA, 800 x 600
48.077
72.188
50.000
+/+
VESA, 800 x 600
46.875
75.000
49.500
+/+
VESA, 1024 x 768
48.363
60.004
65.000
-/-
VESA, 1024 x 768
56.476
70.069
75.000
-/-
VESA, 1024 x 768
60.023
75.029
78.750
+/+
VESA, 1152 x 864
67.500
75.000
108.000
+/+
VESA, 1280 x 800
49.702
59.810
83.500
-/+
VESA, 1280 x 960
60.000
60.000
108.000
+/+
VESA, 1280 x 1024
63.981
60.020
108.000
+/+
VESA, 1280 x 1024
79.976
75.025
135.000
+/+
VESA, 1440 x 900
55.935
59.887
106.500
-/+
VESA, 1440 x 900
70.635
74.984
136.750
-/+
VESA, 1680 x 1050
65.290
59.954
146.250
-/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the
screen horizontally is called the Horizontal Cycle and the inverse number of
the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times
per second to display an image to the user. The frequency of this repetition is
called the Vertical Frequency or Refresh Rate. Unit: Hz
Specifications
General
General
Model Name
SyncMaster 2233NW
LCD Panel
Size
22 inch (55 cm)
Display area
473.76 mm (H) x 296.1 mm (V)
Pixel Pitch
0.282 mm (H) x 0.282 mm (V)
Synchronization
Horizontal
30 ~ 81 kHz
Vertical
56 ~ 75 Hz
Display Color
16.7M
Resolution
Optimum resolution
1680 x 1050@60 Hz
Maximum resolution
1680 x 1050@60 Hz
Input Signal, Terminated
RGB Analog,
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
146 MHz (Analog)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
516.8 x 372.7 x 71.2 mm / 20.3 x 14.7 x 2.8 inch (Without Stand)
516.8 x 421.3 x 208.7 mm / 20.3 x 16.6 x 8.2 inch (With Stand), 4.7 kg / 10.4 lbs
VESA Mounting Interface
100 mm x 100 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
Storage
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the
computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor
installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth)
above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright
sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas
including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor
to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal
operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or
when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in
your computer. Use the software utility installed on your computer to set up this feature.
State
Normal Operation
Power saving mode
Power off (Power button)
EPA/ENERGY 2000
Power Indicator
On
Blinking
Off
Power Consumption
45 watts
Less than 1 watts
Less than 1 watts
This monitor is EPA ENERGY STAR® compliant and ENERGY 2000 compliant when used with
a computer equipped with VESA DPM functionality.
As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets the
ENERGY STAR® guidelines for energy efficiency.
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted
automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual
and adjusts the screen as follows.
Display Mode
Horizontal
Frequency
(kHz)
Vertical
Frequency (Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
IBM, 720 x 400
31.469
70.087
28.322
-/+
MAC, 640 x 480
35.000
66.667
30.240
-/-
MAC, 832 x 624
49.726
74.551
57.284
-/-
MAC, 1152 x 870
68.681
75.062
100.000
-/-
VESA, 640 x 480
31.469
59.94
25.175
-/-
VESA, 640 x 480
37.861
72.809
31.500
-/-
VESA, 640 x 480
37.500
75.000
31.500
-/-
VESA, 800 x 600
35.156
56.250
36.000
+/+
VESA, 800 x 600
37.879
60.317
40.000
+/+
VESA, 800 x 600
48.077
72.188
50.000
+/+
VESA, 800 x 600
46.875
75.000
49.500
+/+
VESA, 1024 x 768
48.363
60.004
65.000
-/-
VESA, 1024 x 768
56.476
70.069
75.000
-/-
VESA, 1024 x 768
60.023
75.029
78.750
+/+
VESA, 1152 x 864
67.500
75.000
108.000
+/+
VESA, 1280 x 800
49.702
59.810
83.500
-/+
VESA, 1280 x 960
60.000
60.000
108.000
+/+
VESA, 1280 x 1024
63.981
60.020
108.000
+/+
VESA, 1280 x 1024
79.976
75.025
135.000
+/+
VESA, 1440 x 900
55.935
59.887
106.500
-/+
VESA, 1440 x 900
70.635
74.984
136.750
-/+
VESA, 1680 x 1050
65.290
59.954
146.250
-/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the
screen horizontally is called the Horizontal Cycle and the inverse number of
the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times
per second to display an image to the user. The frequency of this repetition is
called the Vertical Frequency or Refresh Rate. Unit: Hz
Specifications
General
General
Model Name
SyncMaster 2233NWPLUS
LCD Panel
Size
22 inch (55 cm)
Display area
473.76 mm (H) x 296.1 mm (V)
Pixel Pitch
0.282 mm (H) x 0.282 mm (V)
Synchronization
Horizontal
30 ~ 81 kHz
Vertical
56 ~ 75 Hz
Display Color
16.7M
Resolution
Optimum resolution
1680 x 1050@60 Hz
Maximum resolution
1680 x 1050@60 Hz
Input Signal, Terminated
RGB Analog,
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
146 MHz (Analog)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
516.8 x 372.7 x 71.2 mm / 20.3 x 14.7 x 2.8 inch (Without Stand)
516.8 x 421.3 x 208.7 mm / 20.3 x 16.6 x 8.2 inch (With Stand), 4.7 kg / 10.4 lbs
VESA Mounting Interface
100 mm x 100 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
Storage
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the
computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor
installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth)
above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright
sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas
including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor
to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal
operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or
when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in
your computer. Use the software utility installed on your computer to set up this feature.
State
Normal Operation
Power saving mode
Power off (Power button)
EPA/ENERGY 2000
Power Indicator
On
Blinking
Off
Power Consumption
45 watts
Less than 1 watts
Less than 1 watts
This monitor is EPA ENERGY STAR® compliant and ENERGY 2000 compliant when used with
a computer equipped with VESA DPM functionality.
As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets the
ENERGY STAR® guidelines for energy efficiency.
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted
automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual
and adjusts the screen as follows.
Display Mode
Horizontal
Frequency
(kHz)
Vertical
Frequency (Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
IBM, 720 x 400
31.469
70.087
28.322
-/+
MAC, 640 x 480
35.000
66.667
30.240
-/-
MAC, 832 x 624
49.726
74.551
57.284
-/-
MAC, 1152 x 870
68.681
75.062
100.000
-/-
VESA, 640 x 480
31.469
59.94
25.175
-/-
VESA, 640 x 480
37.861
72.809
31.500
-/-
VESA, 640 x 480
37.500
75.000
31.500
-/-
VESA, 800 x 600
35.156
56.250
36.000
+/+
VESA, 800 x 600
37.879
60.317
40.000
+/+
VESA, 800 x 600
48.077
72.188
50.000
+/+
VESA, 800 x 600
46.875
75.000
49.500
+/+
VESA, 1024 x 768
48.363
60.004
65.000
-/-
VESA, 1024 x 768
56.476
70.069
75.000
-/-
VESA, 1024 x 768
60.023
75.029
78.750
+/+
VESA, 1152 x 864
67.500
75.000
108.000
+/+
VESA, 1280 x 800
49.702
59.810
83.500
-/+
VESA, 1280 x 960
60.000
60.000
108.000
+/+
VESA, 1280 x 1024
63.981
60.020
108.000
+/+
VESA, 1280 x 1024
79.976
75.025
135.000
+/+
VESA, 1440 x 900
55.935
59.887
106.500
-/+
VESA, 1440 x 900
70.635
74.984
136.750
-/+
VESA, 1680 x 1050
65.290
59.954
146.250
-/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the
screen horizontally is called the Horizontal Cycle and the inverse number of
the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times
per second to display an image to the user. The frequency of this repetition is
called the Vertical Frequency or Refresh Rate. Unit: Hz
Specifications
General
General
Model Name
SyncMaster 2233SN
LCD Panel
Size
21.5 inch (54.68 cm)
Display area
476.64 mm (H) x 268.11 mm (V)
Pixel Pitch
0.248 mm (H) x 0.248 mm (V)
Synchronization
Horizontal
31 ~ 80kHz
Vertical
50 ~ 75Hz
Display Color
16.7M
Resolution
Optimum resolution
1920 x 1080@60 Hz
Maximum resolution
1920 x 1080@60 Hz
Input Signal, Terminated
RGB Analog,
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
162 MHz (Analog)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
519 x 344.7 x 71.1 mm (20.4 x 13.6 x 2.8 inch) (Without Stand)
519 x 392.3 x 208.7 mm (20.4 x 15.4 x 8.2 inch) (With Stand) / 4.40 kg (9.7 lbs)
VESA Mounting Interface
100 mm x 100 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
Storage
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the
computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor
installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth)
above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright
sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas
including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor
to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal
operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or
when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in
your computer. Use the software utility installed on your computer to set up this feature.
State
Normal Operation
Power saving mode
Power off (Power button)
EPA/ENERGY 2000
Power Indicator
On
Blinking
Off
Power Consumption
45 watts
Less than 1 watts
Less than 1 watts
This monitor is EPA ENERGY STAR® compliant and ENERG Y2000 compliant when used with
a computer equipped with VESA DPM functionality.
As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets the
ENERGY STAR® guidelines for energy efficiency.
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted
automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual
and adjusts the screen as follows.
Display Mode
Horizontal
Frequency
(kHz)
Vertical
Frequency (Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
VESA, 640 x 480
31.469
59.940
25.175
-/-
VESA, 800 x 600
35.156
56.250
36.000
+/+
VESA, 800 x 600
37.879
60.317
40.000
+/+
VESA, 1024 x 768
48.363
60.004
65.000
-/-
VESA, 1280 x 800
49.702
59.810
83.500
-/+
VESA, 1280 X 960
60.000
60.000
108.000
+/+
VESA, 1280 X 1024
63.981
60.020
108.000
+/+
VESA, 1440 X 900
55.935
59.887
106.500
-/+
VESA, 1600 X 1200
75.000
60.000
162.000
+/+
VESA, 1680 X 1050
65.290
59.954
146.250
-/+
VESA, 1920 X 1080
66.587
59.934
138.500
+/-
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the
screen horizontally is called the Horizontal Cycle and the inverse number of
the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times
per second to display an image to the user. The frequency of this repetition is
called the Vertical Frequency or Refresh Rate. Unit: Hz
Specifications
General
General
Model Name
SyncMaster 2233SNPLUS
LCD Panel
Size
21.5 inch (54.68 cm)
Display area
476.64 mm (H) x 268.11 mm (V)
Pixel Pitch
0.248 mm (H) x 0.248 mm (V)
Synchronization
Horizontal
31 ~ 80kHz
Vertical
50 ~ 75Hz
Display Color
16.7M
Resolution
Optimum resolution
1920 x 1080@60 Hz
Maximum resolution
1920 x 1080@60 Hz
Input Signal, Terminated
RGB Analog,
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
162 MHz (Analog)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
519 x 344.7 x 71.1 mm (20.4 x 13.6 x 2.8 inch) (Without Stand)
519 x 392.3 x 208.7 mm (20.4 x 15.4 x 8.2 inch) (With Stand) / 4.40 kg (9.7 lbs)
VESA Mounting Interface
100 mm x 100 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
Storage
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the
computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor
installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth)
above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright
sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas
including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor
to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal
operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or
when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in
your computer. Use the software utility installed on your computer to set up this feature.
State
Normal Operation
Power saving mode
Power off (Power button)
EPA/ENERGY 2000
Power Indicator
On
Blinking
Off
Power Consumption
45 watts
Less than 1 watts
Less than 1 watts
This monitor is EPA ENERGY STAR® compliant and ENERG Y2000 compliant when used with
a computer equipped with VESA DPM functionality.
As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets the
ENERGY STAR® guidelines for energy efficiency.
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted
automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual
and adjusts the screen as follows.
Display Mode
Horizontal
Frequency
(kHz)
Vertical
Frequency (Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
VESA, 640 x 480
31.469
59.940
25.175
-/-
VESA, 800 x 600
35.156
56.250
36.000
+/+
VESA, 800 x 600
37.879
60.317
40.000
+/+
VESA, 1024 x 768
48.363
60.004
65.000
-/-
VESA, 1280 x 800
49.702
59.810
83.500
-/+
VESA, 1280 X 960
60.000
60.000
108.000
+/+
VESA, 1280 X 1024
63.981
60.020
108.000
+/+
VESA, 1440 X 900
55.935
59.887
106.500
-/+
VESA, 1600 X 1200
75.000
60.000
162.000
+/+
VESA, 1680 X 1050
65.290
59.954
146.250
-/+
VESA, 1920 X 1080
66.587
59.934
138.500
+/-
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the
screen horizontally is called the Horizontal Cycle and the inverse number of
the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times
per second to display an image to the user. The frequency of this repetition is
called the Vertical Frequency or Refresh Rate. Unit: Hz
Specifications
General
General
Model Name
SyncMaster 2233SW
LCD Panel
Size
21.5 inch (54.68 cm)
Display area
476.64 mm (H) x 268.11 mm (V)
Pixel Pitch
0.248 mm (H) x 0.248 mm (V)
Synchronization
Horizontal
31 ~ 80 kHz
Vertical
50 ~ 75 Hz
Display Color
16.7M
Resolution
Optimum resolution
1920 x 1080@60 Hz
Maximum resolution
1920 x 1080@60 Hz
Input Signal, Terminated
RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
162 MHz (Analog, Digital)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
DVI-D to DVI-D connector, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
519 x 344.7 x 71.1 mm (20.4 x 13.6 x 2.8 inch) (Without Stand)
519 x 392.3 x 208.7 mm (20.4 x 15.4 x 8.2 inch) (With Stand) / 4.40 kg (9.7 lbs)
VESA Mounting Interface
100 mm x 100 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Storage
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the
computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor
installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth)
above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright
sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas
including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor
to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal
operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or
when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in
your computer. Use the software utility installed on your computer to set up this feature.
State
Normal Operation
Power saving mode
Power off (Power button)
EPA/ENERGY 2000
Power Indicator
On
Blinking
Off
Power Consumption
45 watts
Less than 1 watts
Less than 1 watts
This monitor is EPA ENERGY STAR® compliant and ENERGY 2000 compliant when used with
a computer equipped with VESA DPM functionality.
As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets the
ENERGY STAR® guidelines for energy efficiency.
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted
automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual
and adjusts the screen as follows.
Display Mode
Horizontal
Frequency
(kHz)
Vertical
Frequency (Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
VESA, 640 x 480
31.469
59.940
25.175
-/-
VESA, 800 x 600
35.156
56.250
36.000
+/+
VESA, 800 x 600
37.879
60.317
40.000
+/+
VESA, 1024 x 768
48.363
60.004
65.000
-/-
VESA, 1280 X 800
49.702
59.810
83.500
-/+
VESA, 1280 X 960
60.000
60.000
108.000
+/+
VESA, 1280 X 1024
63.981
60.020
108.000
+/+
VESA, 1440 X 900
55.935
59.887
106.500
-/+
VESA, 1600 X 1200
75.000
60.000
162.000
+/+
VESA, 1680 X 1050
65.290
59.954
146.250
-/+
VESA, 1920 X 1080
66.587
59.934
138.500
+/-
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the
screen horizontally is called the Horizontal Cycle and the inverse number of
the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times
per second to display an image to the user. The frequency of this repetition is
called the Vertical Frequency or Refresh Rate. Unit: Hz
Specifications
General
General
Model Name
SyncMaster 2233SWPLUS
LCD Panel
Size
21.5 inch (54.68 cm)
Display area
476.64 mm (H) x 268.11 mm (V)
Pixel Pitch
0.248 mm (H) x 0.248 mm (V)
Synchronization
Horizontal
31 ~ 80 kHz
Vertical
50 ~ 75 Hz
Display Color
16.7M
Resolution
Optimum resolution
1920 x 1080@60 Hz
Maximum resolution
1920 x 1080@60 Hz
Input Signal, Terminated
RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
162 MHz (Analog, Digital)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
DVI-D to DVI-D connector, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
519 x 344.7 x 71.1 mm (20.4 x 13.6 x 2.8 inch) (Without Stand)
519 x 392.3 x 208.7 mm (20.4 x 15.4 x 8.2 inch) (With Stand) / 4.40 kg (9.7 lbs)
VESA Mounting Interface
100 mm x 100 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Storage
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the
computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor
installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth)
above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright
sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas
including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor
to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal
operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or
when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in
your computer. Use the software utility installed on your computer to set up this feature.
State
Normal Operation
Power saving mode
Power off (Power button)
EPA/ENERGY 2000
Power Indicator
On
Blinking
Off
Power Consumption
45 watts
Less than 1 watts
Less than 1 watts
This monitor is EPA ENERGY STAR® compliant and ENERGY 2000 compliant when used with
a computer equipped with VESA DPM functionality.
As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets the
ENERGY STAR® guidelines for energy efficiency.
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted
automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual
and adjusts the screen as follows.
Display Mode
Horizontal
Frequency
(kHz)
Vertical
Frequency (Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
VESA, 640 x 480
31.469
59.940
25.175
-/-
VESA, 800 x 600
35.156
56.250
36.000
+/+
VESA, 800 x 600
37.879
60.317
40.000
+/+
VESA, 1024 x 768
48.363
60.004
65.000
-/-
VESA, 1280 X 800
49.702
59.810
83.500
-/+
VESA, 1280 X 960
60.000
60.000
108.000
+/+
VESA, 1280 X 1024
63.981
60.020
108.000
+/+
VESA, 1440 X 900
55.935
59.887
106.500
-/+
VESA, 1600 X 1200
75.000
60.000
162.000
+/+
VESA, 1680 X 1050
65.290
59.954
146.250
-/+
VESA, 1920 X 1080
66.587
59.934
138.500
+/-
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the
screen horizontally is called the Horizontal Cycle and the inverse number of
the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times
per second to display an image to the user. The frequency of this repetition is
called the Vertical Frequency or Refresh Rate. Unit: Hz
Specifications
General
General
Model Name
SyncMaster 2333GWPLUS
LCD Panel
Size
23 inch (58 cm)
Display area
509.76 mm (H) x 286.74 mm (V)
Pixel Pitch
0.2655 mm (H) x 0.2655 mm (V)
Synchronization
Horizontal
30 ~ 75 kHz
Vertical
56 ~ 61 Hz
Display Color
16.7M
Resolution
Optimum resolution
1920 x 1080@60 Hz
Maximum resolution
1920 x 1080@60 Hz
Input Signal, Terminated
RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
164 MHz (Analog, Digital)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable , 1.5m
DVI-D to DVI-D connector, Detachable , 1.5m
Dimensions (W x H x D) / Weight (Simple Stand)
557.3 x 365.8 x 71.5 mm (21.9 x 14.4 x 2.8 inch) (Without Stand)
557.3 x 415.7 x 218.6 mm (21.9 x 16.4 x 8.6 inch) (With Stand) / 5.4 kg (10.4 lbs)
VESA Mounting Interface
100.0 mm x 100.0 mm
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Storage
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the
computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor
installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth)
above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright
sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas
including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor
to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal
operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or
when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in
your computer. Use the software utility installed on your computer to set up this feature.
State
Normal Operation
Power saving mode
Power off (Power button)
EPA/ENERGY 2000
Power Indicator
ON
blinking
Off
Power Consumption
45 watts
Less than 1 watts
Less than 1 watts
This monitor is EPA ENERGY STAR® compliant and ENERGY 2000 compliant when used with
a computer equipped with VESA DPM functionality.
As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets the
ENERGY STAR® guidelines for energy efficiency.
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted
automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual
and adjusts the screen as follows.
Display Mode
Horizontal
Frequency
(kHz)
Vertical
Frequency (Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
VESA, 640 x 480
31.469
59.940
25.175
-/-
VESA, 800 x 600
35.156
56.250
36.000
+/+
VESA, 800 x 600
37.879
60.317
40.000
+/+
VESA, 1024 x 768
48.363
60.004
65.000
-/-
VESA, 1280 X 800
49.702
59.810
83.500
-/+
VESA, 1280 X 960
60.000
60.000
108.000
+/+
VESA, 1280 X 1024
63.981
60.020
108.000
+/+
VESA, 1440 X 900
55.935
59.887
106.500
-/+
VESA, 1600 X 1200
75.000
60.000
162.000
+/+
VESA, 1680 X 1050
65.290
59.954
146.250
-/+
VESA, 1920 X 1080
66.587
59.934
138.500
+/-
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the
screen horizontally is called the Horizontal Cycle and the inverse number of
the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times
per second to display an image to the user. The frequency of this repetition is
called the Vertical Frequency or Refresh Rate. Unit: Hz
Specifications
General
General
Model Name
SyncMaster 2333SW
LCD Panel
Size
23 inch (58 cm)
Display area
509.76 mm (H) x 286.74 mm (V)
Pixel Pitch
0.2655 mm (H) x 0.2655 mm (V)
Synchronization
Horizontal
30 ~ 75 kHz
Vertical
56 ~ 61 Hz
Display Color
16.7M
Resolution
Optimum resolution
1920 x 1080@60 Hz
Maximum resolution
1920 x 1080@60 Hz
Input Signal, Terminated
RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
164 MHz (Analog, Digital)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
DVI-D to DVI-D connector, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
557.3 x 365.8 x 71.5 mm (21.9 x 14.4 x 2.8 inch) (Without Stand)
557.3 x 415.7 x 218.6 mm (21.9 x 16.4 x 8.6 inch) (With Stand) / 5.4 kg (11.9 lbs)
VESA Mounting Interface
100.0 mm x 100.0 mm
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Storage
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the
computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor
installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth)
above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright
sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas
including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor
to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal
operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or
when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in
your computer. Use the software utility installed on your computer to set up this feature.
State
Normal Operation
Power saving mode
Power off (Power button)
EPA/ENERGY 2000
Power Indicator
ON
blinking
Off
Power Consumption
45 watts
Less than 1 watts
Less than 1 watts
This monitor is EPA ENERGY STAR® compliant and ENERGY 2000 compliant when used with
a computer equipped with VESA DPM functionality.
As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets the
ENERGY STAR® guidelines for energy efficiency.
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted
automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual
and adjusts the screen as follows.
Display Mode
Horizontal
Frequency
(kHz)
Vertical
Frequency (Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
VESA, 640 x 480
31.469
59.940
25.175
-/-
VESA, 800 x 600
35.156
56.250
36.000
+/+
VESA, 800 x 600
37.879
60.317
40.000
+/+
VESA, 1024 x 768
48.363
60.004
65.000
-/-
VESA, 1280 X 800
49.702
59.810
83.500
-/+
VESA, 1280 X 960
60.000
60.000
108.000
+/+
VESA, 1280 X 1024
63.981
60.020
108.000
+/+
VESA, 1440 X 900
55.935
59.887
106.500
-/+
VESA, 1600 X 1200
75.000
60.000
162.000
+/+
VESA, 1680 X 1050
65.290
59.954
146.250
-/+
VESA, 1920 X 1080
66.587
59.934
138.500
+/-
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the
screen horizontally is called the Horizontal Cycle and the inverse number of
the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times
per second to display an image to the user. The frequency of this repetition is
called the Vertical Frequency or Refresh Rate. Unit: Hz
Specifications
General
General
Model Name
SyncMaster 2333SWPLUS
LCD Panel
Size
23 inch (58 cm)
Display area
509.76 mm (H) x 286.74 mm (V)
Pixel Pitch
0.2655 mm (H) x 0.2655 mm (V)
Synchronization
Horizontal
30 ~ 75 kHz
Vertical
56 ~ 61 Hz
Display Color
16.7M
Resolution
Optimum resolution
1920 x 1080@60 Hz
Maximum resolution
1920 x 1080@60 Hz
Input Signal, Terminated
RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
164 MHz (Analog, Digital)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
DVI-D to DVI-D connector, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
557.3 x 365.8 x 71.5 mm (21.9 x 14.4 x 2.8 inch) (Without Stand)
557.3 x 415.7 x 218.6 mm (21.9 x 16.4 x 8.6 inch) (With Stand) / 5.4 kg (11.9 lbs)
VESA Mounting Interface
100.0 mm x 100.0 mm
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Storage
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the
computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor
installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth)
above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright
sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas
including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor
to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal
operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or
when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in
your computer. Use the software utility installed on your computer to set up this feature.
State
Normal Operation
Power saving mode
Power off (Power button)
EPA/ENERGY 2000
Power Indicator
ON
blinking
Off
Power Consumption
45 watts
Less than 1 watts
Less than 1 watts
This monitor is EPA ENERGY STAR® compliant and ENERGY 2000 compliant when used with
a computer equipped with VESA DPM functionality.
As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets the
ENERGY STAR® guidelines for energy efficiency.
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted
automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual
and adjusts the screen as follows.
Display Mode
Horizontal
Frequency
(kHz)
Vertical
Frequency (Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
VESA, 640 x 480
31.469
59.940
25.175
-/-
VESA, 800 x 600
35.156
56.250
36.000
+/+
VESA, 800 x 600
37.879
60.317
40.000
+/+
VESA, 1024 x 768
48.363
60.004
65.000
-/-
VESA, 1280 X 800
49.702
59.810
83.500
-/+
VESA, 1280 X 960
60.000
60.000
108.000
+/+
VESA, 1280 X 1024
63.981
60.020
108.000
+/+
VESA, 1440 X 900
55.935
59.887
106.500
-/+
VESA, 1600 X 1200
75.000
60.000
162.000
+/+
VESA, 1680 X 1050
65.290
59.954
146.250
-/+
VESA, 1920 X 1080
66.587
59.934
138.500
+/-
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the
screen horizontally is called the Horizontal Cycle and the inverse number of
the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times
per second to display an image to the user. The frequency of this repetition is
called the Vertical Frequency or Refresh Rate. Unit: Hz
Specifications
General
General
Model Name
SyncMaster 2433BW
LCD Panel
Size
24 inch (61 cm)
Display area
518.4 mm (H) x 324.0 mm (V)
Pixel Pitch
0.270 mm (H) x 0.270 mm (V)
Synchronization
Horizontal
30 ~ 81 kHz
Vertical
50 ~ 63 Hz
Display Color
16.7M
Resolution
Optimum resolution
1920 x 1200@60 Hz
Maximum resolution
1920 x 1200@60 Hz
Input Signal, Terminated
RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
164 MHz (Analog, Digital)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
DVI-D to DVI-D connector, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
569.5 x 403.0 x 71.1 mm / 22.4 x 15.9 x 2.8 inch (Without Stand)
569.5 x 453.4 x 218.7 mm / 22.4 x 17.9 x 8.6 inch (With Stand), 5.8 kg / 12.8 lbs
VESA Mounting Interface
100 mm x 100 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Storage
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the
computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor
installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth)
above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright
sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas
including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor
to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal
operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or
when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in
your computer. Use the software utility installed on your computer to set up this feature.
State
Normal Operation
Power saving mode
Power off (Power button)
EPA/ENERGY 2000
Power Indicator
On
Blinking
Off
Power Consumption
50 watts
Less than 1 watts
Less than 1 watts
This monitor is EPA ENERGY STAR® compliant and ENERGY2000 compliant when used with
a computer equipped with VESA DPM functionality.
As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets the
ENERGY STAR® guidelines for energy efficiency.
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted
automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual
and adjusts the screen as follows.
Display Mode
Horizontal
Frequency
(kHz)
Vertical
Frequency (Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
VESA, 640 x 480
31,469
59,940
25,175
-/-
VESA, 800 x 600
35,156
56,250
36,000
+/+
VESA, 800 x 600
37,879
60,317
40,000
+/+
VESA,1024 x 768
48,363
60,004
65,000
-/-
VESA, 1280 x 800
49,702
59,810
83,500
-/+
VESA, 1280 X 960
60,000
60,000
108,000
+/+
VESA, 1280 X 1024
63,981
60,020
108,000
+/+
VESA,1440 x 900
55,935
59,887
106,500
-/+
VESA,1600 X 1200
75,000
60,000
162,000
+/+
VESA, 1680 x 1050
65,290
59,954
146,250
-/+
VESA, 1920 X 1200
74,556
59,885
193,250
-/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the
screen horizontally is called the Horizontal Cycle and the inverse number of
the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times
per second to display an image to the user. The frequency of this repetition is
called the Vertical Frequency or Refresh Rate. Unit: Hz
Specifications
General
General
Model Name
SyncMaster 2433BWPLUS
LCD Panel
Size
24 inch (61 cm)
Display area
518.4 mm (H) x 324.0 mm (V)
Pixel Pitch
0.270 mm (H) x 0.270 mm (V)
Synchronization
Horizontal
30 ~ 81 kHz
Vertical
50 ~ 63 Hz
Display Color
16.7M
Resolution
Optimum resolution
1920 x 1200@60 Hz
Maximum resolution
1920 x 1200@60 Hz
Input Signal, Terminated
RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
164 MHz (Analog, Digital)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
DVI-D to DVI-D connector, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
569.5 x 403.0 x 71.1 mm / 22.4 x 15.9 x 2.8 inch (Without Stand)
569.5 x 453.4 x 218.7 mm / 22.4 x 17.9 x 8.6 inch (With Stand), 5.8 kg / 12.8 lbs
VESA Mounting Interface
100 mm x 100 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Storage
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the
computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor
installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth)
above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright
sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas
including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor
to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal
operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or
when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in
your computer. Use the software utility installed on your computer to set up this feature.
State
Normal Operation
Power saving mode
Power off (Power button)
EPA/ENERGY 2000
Power Indicator
On
Blinking
Off
Power Consumption
50 watts
Less than 1 watts
Less than 1 watts
This monitor is EPA ENERGY STAR® compliant and ENERGY2000 compliant when used with
a computer equipped with VESA DPM functionality.
As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets the
ENERGY STAR® guidelines for energy efficiency.
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted
automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual
and adjusts the screen as follows.
Display Mode
Horizontal
Frequency
(kHz)
Vertical
Frequency (Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
VESA, 640 x 480
31,469
59,940
25,175
-/-
VESA, 800 x 600
35,156
56,250
36,000
+/+
VESA, 800 x 600
37,879
60,317
40,000
+/+
VESA,1024 x 768
48,363
60,004
65,000
-/-
VESA, 1280 x 800
49,702
59,810
83,500
-/+
VESA, 1280 X 960
60,000
60,000
108,000
+/+
VESA, 1280 X 1024
63,981
60,020
108,000
+/+
VESA,1440 x 900
55,935
59,887
106,500
-/+
VESA,1600 X 1200
75,000
60,000
162,000
+/+
VESA, 1680 x 1050
65,290
59,954
146,250
-/+
VESA, 1920 X 1200
74,556
59,885
193,250
-/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the
screen horizontally is called the Horizontal Cycle and the inverse number of
the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times
per second to display an image to the user. The frequency of this repetition is
called the Vertical Frequency or Refresh Rate. Unit: Hz
Specifications
General
General
Model Name
SyncMaster 2433GW
LCD Panel
Size
24 inch (61 cm)
Display area
518.4 mm (H) x 324.0 mm (V)
Pixel Pitch
0.270 mm (H) x 0.270 mm (V)
Synchronization
Horizontal
30 ~ 81 kHz
Vertical
50 ~ 63 Hz
Display Color
16.7M
Resolution
Optimum resolution
1920 x 1200@60 Hz
Maximum resolution
1920 x 1200@60 Hz
Input Signal, Terminated
RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
164 MHz (Analog, Digital)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
DVI-D to DVI-D connector, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
569.5 x 403.0 x 71.1 mm / 22.4 x 15.9 x 2.8 inch (Without Stand)
569.5 x 453.4 x 218.7 mm / 22.4 x 17.9 x 8.6 inch (With Stand), 5.8 kg / 12.8 lbs
VESA Mounting Interface
100 mm x 100 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Storage
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the
computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor
installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth)
above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright
sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas
including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor
to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal
operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or
when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in
your computer. Use the software utility installed on your computer to set up this feature.
State
Normal Operation
Power saving mode
Power off (Power button)
EPA/ENERGY 2000
Power Indicator
On
Blinking
Off
Power Consumption
50 watts
Less than 1 watts
Less than 1 watts
This monitor is EPA ENERGY STAR® compliant and ENERGY2000 compliant when used with
a computer equipped with VESA DPM functionality.
As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets the
ENERGY STAR® guidelines for energy efficiency.
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted
automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual
and adjusts the screen as follows.
Display Mode
Horizontal
Frequency
(kHz)
Vertical
Frequency (Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
VESA, 640 x 480
31,469
59,940
25,175
-/-
VESA, 800 x 600
35,156
56,250
36,000
+/+
VESA, 800 x 600
37,879
60,317
40,000
+/+
VESA,1024 x 768
48,363
60,004
65,000
-/-
VESA, 1280 x 800
49,702
59,810
83,500
-/+
VESA, 1280 X 960
60,000
60,000
108,000
+/+
VESA, 1280 X 1024
63,981
60,020
108,000
+/+
VESA,1440 x 900
55,935
59,887
106,500
-/+
VESA,1600 X 1200
75,000
60,000
162,000
+/+
VESA, 1680 x 1050
65,290
59,954
146,250
-/+
VESA, 1920 X 1200
74,556
59,885
193,250
-/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the
screen horizontally is called the Horizontal Cycle and the inverse number of
the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times
per second to display an image to the user. The frequency of this repetition is
called the Vertical Frequency or Refresh Rate. Unit: Hz
Specifications
General
General
Model Name
SyncMaster 2433GWPLUS
LCD Panel
Size
24 inch (61 cm)
Display area
518.4 mm (H) x 324.0 mm (V)
Pixel Pitch
0.270 mm (H) x 0.270 mm (V)
Synchronization
Horizontal
30 ~ 81 kHz
Vertical
50 ~ 63 Hz
Display Color
16.7M
Resolution
Optimum resolution
1920 x 1200@60 Hz
Maximum resolution
1920 x 1200@60 Hz
Input Signal, Terminated
RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
164 MHz (Analog, Digital)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
DVI-D to DVI-D connector, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
569.5 x 403.0 x 71.1 mm / 22.4 x 15.9 x 2.8 inch (Without Stand)
569.5 x 453.4 x 218.7 mm / 22.4 x 17.9 x 8.6 inch (With Stand), 5.8 kg / 12.8 lbs
VESA Mounting Interface
100 mm x 100 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Storage
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the
computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor
installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth)
above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright
sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas
including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor
to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal
operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or
when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in
your computer. Use the software utility installed on your computer to set up this feature.
State
Normal Operation
Power saving mode
Power off (Power button)
EPA/ENERGY 2000
Power Indicator
On
Blinking
Off
Power Consumption
50 watts
Less than 1 watts
Less than 1 watts
This monitor is EPA ENERGY STAR® compliant and ENERGY2000 compliant when used with
a computer equipped with VESA DPM functionality.
As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets the
ENERGY STAR® guidelines for energy efficiency.
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted
automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual
and adjusts the screen as follows.
Display Mode
Horizontal
Frequency
(kHz)
Vertical
Frequency (Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
VESA, 640 x 480
31,469
59,940
25,175
-/-
VESA, 800 x 600
35,156
56,250
36,000
+/+
VESA, 800 x 600
37,879
60,317
40,000
+/+
VESA,1024 x 768
48,363
60,004
65,000
-/-
VESA, 1280 x 800
49,702
59,810
83,500
-/+
VESA, 1280 X 960
60,000
60,000
108,000
+/+
VESA, 1280 X 1024
63,981
60,020
108,000
+/+
VESA,1440 x 900
55,935
59,887
106,500
-/+
VESA,1600 X 1200
75,000
60,000
162,000
+/+
VESA, 1680 x 1050
65,290
59,954
146,250
-/+
VESA, 1920 X 1200
74,556
59,885
193,250
-/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the
screen horizontally is called the Horizontal Cycle and the inverse number of
the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times
per second to display an image to the user. The frequency of this repetition is
called the Vertical Frequency or Refresh Rate. Unit: Hz
Specifications
General
General
Model Name
SyncMaster 2433LW
LCD Panel
Size
23.6 inch (59.8 cm)
Display area
521.28 mm (H) x 293.22 mm (V)
Pixel Pitch
0.2715 mm (H) x 0.2715 mm (V)
Synchronization
Horizontal
30 ~ 81kHz
Vertical
56 ~ 60 Hz
Display Color
16.7M
Resolution
Optimum resolution
1920 x 1080@60 Hz
Maximum resolution
1920 x 1080@60 Hz
Input Signal, Terminated
RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB
0.7 Vp-p ± 5 %
Separate H/V sync, Composite, SOG
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
164 MHz (Analog, Digital)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin - to - 15pin D-sub cable, Detachable
DVI-D to DVI-D connector, Detachable
Dimensions (W x H x D) / Weight (Simple Stand)
579.1 x378.2 x 75.6 mm / 22.8 x 14.9 x 3.0 inch (Without Stand)
579.1 x 428.0 x 218.6 mm / 22.8 x 16.9 x 8.6 inch (With Stand), 5.6 kg / 12.3 lbs
VESA Mounting Interface
100 mm x 100 mm (For use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Operating
Humidity : 10 % ~ 80 %, non-condensing
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Storage
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the
computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor
installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth)
above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright
sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas
including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)
Specifications
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor
to low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal
operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or
when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in
your computer. Use the software utility installed on your computer to set up this feature.
State
Normal Operation
Power saving mode
Power off (Power button)
EPA/ENERGY 2000
Power Indicator
On
Blinking
Off
Power Consumption
44 watts
Less than 1 watts
Less than 1 watts
This monitor is EPA ENERGY STAR® compliant and ENERGY2000 compliant when used with
a computer equipped with VESA DPM functionality.
As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets the
ENERGY STAR® guidelines for energy efficiency.
Specifications
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted
automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual
and adjusts the screen as follows.
Display Mode
Horizontal
Frequency
(kHz)
Vertical
Frequency (Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
VESA, 640 x 480
31,469
59,940
25,175
-/-
VESA, 800 x 600
35,156
56,250
36,000
+/+
VESA, 800 x 600
37,879
60,317
40,000
+/+
VESA,1024 x 768
48,363
60,004
65,000
-/-
VESA, 1280 x 800
49,702
59,810
83,500
-/+
VESA, 1280 X 960
60,000
60,000
108,000
+/+
VESA, 1280 X 1024
63,981
60,020
108,000
+/+
VESA,1440 x 900
55,935
59,887
106,500
-/+
VESA,1600 X 1200
75,000
60,000
162,000
+/+
VESA, 1680 x 1050
65,290
59,954
146,250
-/+
VESA, 1920 X 1200
74,556
59,885
193,250
-/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the
screen horizontally is called the Horizontal Cycle and the inverse number of
the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many times
per second to display an image to the user. The frequency of this repetition is
called the Vertical Frequency or Refresh Rate. Unit: Hz
Information
For Better Display
Adjust the computer resolution and screen injection rate (refresh rate) on the computer
as described below to enjoy the best picture quality. You can have an uneven picture quality
on screen if the best picture quality is not provided for TFT-LCD.
•
Resolution: **** x ****
•
Vertical frequency (refresh rate): 60 Hz
TFT-LCD panels manufactured by using advanced semiconductor technology with a
precision of 1ppm (one millionth) and above is used for this product. But the pixels of RED,
GREEN, BLUE and WHITE color seem to be bright sometimes or some of black pixels
could be seen. This is not from bad quality and you can use it without any problems.
When cleaning the monitor and the panel outside, please apply the recommended small
amount of cleaner by using a soft cloth to polish. Do not force the LCD area but rub softly.
If excessive force is applied, you may stain it.
If you are not satisfied with the picture quality, you can get better quality of picture by
performing the "Auto Adjustment function" in display screen that is appeared as window
termination button is pressed.
If there's still noise after the automatic adjustment, use the Fine/Coarse adjustment function.
When viewing a fixed screen for an extended period of time, a residual image or blurriness may appear.
Change the mode to energy save or set a screensaver to move the picture when you need
to be away from the monitor for an extended period of time.
PRODUCT INFORMATION (Image Retention Free)
LCD Monitors and TVs may have image retention when switching from one image to another especially after displaying a stationary image for a long time.
This guide is to demonstrate correct usage of LCD products in order to protect them from Image
retention.
Warranty
Warranty does not cover any damage caused by image retention.
Burn-in is not covered by the warranty.
What is Image retention ?
During normal operation of a LCD panel, pixel image retention doesn't occur. However, if
the same image is displayed for a long time, a slight difference in electric charge accumulates between the two electrodes which encase the liquid crystal. This may cause the liquid
crystal to build up in a certain areas of the display. Thus, the previous image is retained
45
Information
when switching to a new video image. All display products, including LCD, are subject to
image retention. This is not a product defect.
Please follow the suggestions below to protect your LCD from image retention.
Power Off, Screen Saver, or Power Save Mode
Ex)
•
•
Turn the power off when using a stationary pattern.
•
Turn the power off for 4 hours after 20 hours in use
•
Turn the power off for 2 hours after 12 hours in use
Use a Screen saver if possible
•
•
Screen saver in one color or a moving image is recommended.
Set the Monitor to power off with the PC Display Properties Power Scheme.
Suggestions for specific applications
Ex) Airports, Transit Stations, Stock Markets, Banks, and Controlling Systems We recommend that you follow set up of your display system program as below:
Display Information together with Logo or Moving image cycle.
Ex) Cycle : Display Information for 1 hour followed by a Display Logo or moving image
for 1 minute.
Change the Color Information periodically (Use 2 different colors).
Ex) Rotate the Color Information with 2 colors every 30 minutes.
Avoid using a combination of characters and background color with large difference in
luminance.
Avoid using Grey colors, which can cause Image retention easily.
•
Avoid: Colors with big difference in luminance (Black & White, Grey)
Ex)
•
Recommended settings: Bright colors with little difference in luminance
•
Change the characters color and background color every 30 minutes
46
Information
Ex)
•
Every 30 minutes, change the characters with movement.
Ex)
The best way to protect your monitor from Image retention is to set your PC or System
to operate a Screen Saver program when you are not using it.
Image retention may not occur when a LCD panel is operated under normal conditions.
Normal conditions are defined as continuously changing video patterns. When the LCD
panel is operated for a long time with a fixed pattern (-over 12 hours-), there may be slight
difference in voltage between electrodes that work the liquid crystal (LC) in a pixel. The
voltage difference between electrodes increases with time, forcing the liquid crystal to lean.
When this occurs, the previous image may be seen when the pattern is changed.
To prevent this, the accumulated voltage difference must be decreased.
47
Information
Our LCD Monitor satisfies ISO13406-2 Pixel fault Class II
48
Appendix
Contact SAMSUNG WORLDWIDE
Note
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG
customer care center.
North America
U.S.A
1-800-SAMSUNG(726-7864)
http://www.samsung.com/us
CANADA
1-800-SAMSUNG(726-7864)
http://www.samsung.com/ca
MEXICO
01-800-SAMSUNG(726-7864) http://www.samsung.com/mx
Latin America
ARGENTINA
0800-333-3733
http://www.samsung.com/ar
BRAZIL
0800-124-421
http://www.samsung.com/br
4004-0000
CHILE
800-SAMSUNG(726-7864)
http://www.samsung.com/cl
COLOMBIA
01-8000112112
http://www.samsung.com/co
COSTA RICA
0-800-507-7267
http://www.samsung.com/latin
ECUADOR
1-800-10-7267
http://www.samsung.com/latin
EL SALVADOR
800-6225
http://www.samsung.com/latin
GUATEMALA
1-800-299-0013
http://www.samsung.com/latin
HONDURAS
800-7919267
http://www.samsung.com/latin
JAMAICA
1-800-234-7267
http://www.samsung.com/latin
NICARAGUA
00-1800-5077267
http://www.samsung.com/latin
PANAMA
800-7267
http://www.samsung.com/latin
PUERTO RICO
1-800-682-3180
http://www.samsung.com/latin
REP. DOMINICA
1-800-751-2676
http://www.samsung.com/latin
TRINIDAD & TO- 1-800-SAMSUNG(726-7864)
BAGO
http://www.samsung.com/latin
VENEZUELA
http://www.samsung.com/latin
0-800-100-5303
Europe
AUSTRIA
0810 - SAMSUNG(7267864, € http://www.samsung.com/at
0.07/min)
BELGIUM
02 201 2418
http://www.samsung.com/be
(Dutch)
http://www.samsung.com/be_fr
(French)
CZECH REPUBLIC 800 - SAMSUNG (800-726786) http://www.samsung.com/cz
DENMARK
8 - SAMSUNG (7267864)
http://www.samsung.com/dk
EIRE
0818 717 100
http://www.samsung.com/ie
49
Appendix
Europe
FINLAND
30 - 6227 515
http://www.samsung.com/fi
FRANCE
01 4863 0000
http://www.samsung.com/fr
GERMANY
01805 - SAMSUNG (7267864, € http://www.samsung.de
0.14/Min)
HUNGARY
06-80-SAMSUNG(726-7864)
http://www.samsung.com/hu
ITALIA
800-SAMSUNG(726-7864)
http://www.samsung.com/it
LUXEMBURG
02 261 03 710
http://www.samsung.com/lu
NETHERLANDS
0900
SAMSUNG http://www.samsung.com/nl
(0900-7267864) (€ 0.10/Min)
NORWAY
3 - SAMSUNG (7267864)
http://www.samsung.com/no
POLAND
0 801 1SAMSUNG (172678)
http://www.samsung.com/pl
022 - 607 - 93 - 33
PORTUGAL
808 20 - SAMSUNG (7267864) http://www.samsung.com/pt
SLOVAKIA
0800-SAMSUNG(726-7864)
SPAIN
902 - 1 - SAMSUNG (902 172 http://www.samsung.com/es
678)
SWEDEN
075 - SAMSUNG (726 78 64)
http://www.samsung.com/se
SWITZERLAND
0848-SAMSUNG(7267864,
CHF 0.08/min)
http://www.samsung.com/ch
U.K
0845 SAMSUNG (7267864)
http://www.samsung.com/uk
http://www.samsung.com/sk
CIS
ESTONIA
800-7267
http://www.samsung.com/ee
LATVIA
8000-7267
http://www.samsung.com/lv
LITHUANIA
8-800-77777
http://www.samsung.com/lt
KAZAKHSTAN
8-10-800-500-55-500
http://www.samsung.com/kz_ru
KYRGYZSTAN
00-800-500-55-500
RUSSIA
8-800-555-55-55
TADJIKISTAN
8-10-800-500-55-500
UKRAINE
8-800-502-0000
http://www.samsung.ua
UZBEKISTAN
8-10-800-500-55-500
http://www.samsung.com/kz_ru
http://www.samsung.ru
Asia Pacific
AUSTRALIA
1300 362 603
http://www.samsung.com/au
CHINA
800-810-5858
http://www.samsung.com/cn
400-810-5858
010-6475 1880
INDIA
HONG KONG:3698 - 4698
http://www.samsung.com/hk
3030 8282
http://www.samsung.com/in
1800 110011
1-800-3000-8282
INDONESIA
0800-112-8888
http://www.samsung.com/id
50
Appendix
Asia Pacific
JAPAN
0120-327-527
http://www.samsung.com/jp
MALAYSIA
1800-88-9999
http://www.samsung.com/my
NEW ZEALAND
0800 SAMSUNG (0800 726 http://www.samsung.com/nz
786)
PHILIPPINES
1800-10-SAMSUNG(726-7864) http://www.samsung.com/ph
1800-3-SAMSUNG(726-7864)
02-5805777
SINGAPORE
1800-SAMSUNG(726-7864)
http://www.samsung.com/sg
THAILAND
1800-29-3232
http://www.samsung.com/th
02-689-3232
TAIWAN
0800-329-999
http://www.samsung.com/tw
VIETNAM
1 800 588 889
http://www.samsung.com/vn
Middle East & Africa
SOUTH AFRICA
0860-SAMSUNG(726-7864)
http://www.samsung.com/za
TURKEY
444 77 11
http://www.samsung.com/tr
U.A.E
800-SAMSUNG(726-7864)
http://www.samsung.com/ae
8000-4726
Terms
Dot Pitch
The image on a monitor is composed of red, green and blue dots.
The closer the dots, the higher the resolution. The distance between two dots of the same color is called the 'Dot Pitch'. Unit:
mm
Vertical Frequency
The screen must be redrawn several times per second in order to
create and display an image for the user. The frequency of this
repetition per second is called the Vertical Frequency or Refresh
Rate. Unit: Hz
Example: If the same light repeats itself 60 times per second, this
is regarded as 60 Hz.
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge
of the screen horizontally is called the Horizontal Cycle. The inverse number of the Horizontal Cycle is called Horizontal Frequency. Unit: kHz
Interlace
Methods
Showing the horizontal lines of the screen from the top to the bottom sequentially is called the Non-Interlace method while showing odd lines and then even lines in turn is called the Interlace
method. The Non-Interlace method is used for the majority of
monitors to ensure a clear image. The Interlace method is the same
as that used in TVs.
and
Plug & Play
Non-Interlace
This is a function that provides the best quality screen for the user
by allowing the computer and the monitor to exchange information automatically. This monitor follows the international standard
VESA DDC for the Plug & Play function.
51
Appendix
Resolution
The number of horizontal and vertical dots used to compose the
screen image is called the 'resolution'. This number shows the accuracy of the display. A high resolution is good for performing
multiple tasks as more image information can be shown on the
screen.
Example: If the resolution is **** x ****, this means the screen
is composed of **** horizontal dots (horizontal resolution) and
**** vertical lines (vertical resolution).
Correct Disposal
Correct Disposal of This Product (Waste Electrical & Electronic Equipment) Europe only
(Applicable in the European Union and other European
countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g.
charger, headset, USB cable) should not be disposed of
with other household waste at the end of their working life.
To prevent possible harm to the environment or human
health from uncontrolled waste disposal, please separate
these items from other types of waste and recycle them
responsibly to promote the sustainable reuse of material
resources.
Household users should contact either the retailer where
they purchased this product, or their local government office, for details of where and how they can take these items
for environmentally safe recycling.
Business users should contact their supplier and check the
terms and conditions of the purchase contract. This product and its electronic accessories should not be mixed with
other commercial wastes for disposal.
Authority
Information in this document is subject to change without notice.
© 2009 Samsung Electronics Co., Ltd. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co.,
Ltd. is strictly forbidden.
Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
Samsung is the registered trademark of Samsung Electronics Co., Ltd.; Microsoft, Windows and Windows NT are registered trademarks of Microsoft Corporation; VESA, DPM and DDC are registered
trademarks of Video Electronics Standard Association; the ENERGY STAR® name and logo are registered trademarks of the U.S. Environmental Protection Agency (EPA). As an ENERGY STAR®
Partner, Samsung Electronics Co., Ltd. has determined that this product meets the ENERGY
STAR® guidelines for energy efficiency. All other product names mentioned herein may be the trademarks or registered trademarks of their respective owners.
52
Download PDF