Samsung | 720TD | Samsung 720TD User Manual

SyncMaster 720TD
Install drivers
Install programs
Notation
Failure to follow directions noted by this symbol could result in bodily harm or damage to
equipment.
Prohibited
Important to read and understand at all times
Do not disassemble
Disconnect the plug from the outlet
Do not touch
Grounding to prevent an electric shock
Power
When not used for extended period of time, set your computer to DPMS.
If using a screen saver, set it to the active screen mode.
Do not use a damaged or loose plug.
This may cause an electric shock or fire.
Do not pull the plug out by the wire nor touch the plug with wet hands.
This may cause an electric shock or fire.
Use only a properly grounded plug and receptacle.
An improper ground may cause electric shock or equipment damage.
Insert the power plug firmly so that it does not come loose.
A bad connection may cause fire.
Do not excessively bend the plug and wire nor place heavy objects upon them, which
could cause damage.
This may cause an electric shock or fire.
Do not connect too many extension cords or plugs to an outlet.
This may cause fire.
Installation
Be sure to contact an authorized Service Center when installing your set in a location
with heavy dust, high or low temperatures, high humidity, and chemical substances,
or where it will be operated for 24 hours continuously such as an airport, train station
or etc.
Failure to do so may cause serious damage to your set.
Put your monitor in a location with low humidity and a minimum of dust.
Failure to do so may cause an electric shock or fire inside the monitor.
Do not drop the monitor when moving it.
This may cause damage to the product or human body.
Install the monitor base in a showcase or shelf so that the end of the base does not
protrude from the showcase or shelf.
Dropping the product may cause damage to the product or personal injury.
Do not place the product on an unstable or small surface area.
Place the product on an even, stable surface, as the product may fall and cause
harm to someone walking by, specifically children.
Do not place the product on the floor.
Someone, specifically children could trip over it.
Keep any flammable objects such as candles, insecticides or cigarettes away from
the product.
Otherwise, this may cause a fire.
Keep any heating devices away from the power cable.
A melted coating may lead to electric shock or fire.
Do not install the product in places with poor ventilation, for instance, a bookshelf,
closet, etc.
Any increase in internal temperature may cause fire.
Set down the monitor carefully.
The monitor could be damaged or broken.
Do not place the monitor face down.
The TFT-LCD surface may be damaged.
Installing a wall bracket must be done by a qualified professional.
Installation by unqualified personnel may result in injury.
Always use the mounting device specified in the owner's manual.
When installing the product, make sure to keep it away from the wall (more than 10
cm/4 inch ) for ventilation purposes.
Poor ventilation may cause an increase in the internal temperature of the product,
resulting in a shortened component life and degraded performance.
Cleaning and Use
When cleaning the monitor case or the surface of the TFT-LCD screen, wipe with a
slightly moistened, soft fabric.
Do not spray water or detergent directly on the monitor.
This may cause damage, electric shock or fire.
Use the recommended detergent with a smooth cloth.
If the connector between the plug and the pin is dusty or dirty, clean it properly with a
dry cloth.
A dirty connector may cause an electric shock or fire.
Make sure to unplug the power cord before cleaning the product.
Otherwise, this may cause electric shock or fire.
Unplug the power cord from the power outlet and wipe the product using a soft, dry
cloth.
Do not use any chemicals such as wax, benzene, alcohol, thinners, insecticide, air
freshener, lubricant or detergent.
Contact the Service Center or Customer Center for interior cleaning once a year.
Keep the product's interior clean.
Dust which has accumulated in the interior over an extended period of time may
cause malfunction or fire.
Tablet
Avoid dropping or causing any impact to the electronic pen.
There is a danger of damage, overheating or explosion.
Keep the electronic pen away from heaters and under no circumstances leave the
electronic pen in any heating device such as a microwave oven.
There is a danger of overheating or explosion.
Avoid making contact between the charge terminal of the electronic pen to any metal
such as a necklace, coin, key, etc.
There is a danger of overheating or explosion.
Keep the electronic pen away from direct sunlight or moisture and keep it at a
temperature between 0 °C ~ +40 °C.
There is a danger of explosion due to the device inflating.
Do not let children or pets make oral contact with the electronic pen.
If the electronic pen is wet or damaged, it may cause fire or explode.
Oral contact with the electronic pen or using a damaged battery may adversely
affect the human body.
If the battery in the electronic pen is damaged and human skin is contaminated
with the fluid from the battery, wash the skin with flowing water for 1 to 2 minutes.
Do not damage the electronic pen with a gimlet or tack and do not disassemble the
electronic pen.
There is a danger of a fire or explosion.
Others
Do not remove cover (or back).
This may cause an electric shock or fire.
Refer servicing to qualified service personnel.
If your monitor does not operate normally - in particular, if there are any unusual
sounds or smells coming from it - unplug it immediately and contact an authorized
dealer or service.
This may cause an electric shock or fire.
Keep the product away from places exposed to oil, smoke or moisture; do not install
inside a vehicle.
This may cause malfunction, an electric shock or fire.
Especially avoid operating the monitor near water or outdoors where the monitor
could be exposed to snow or rain.
If the monitor is dropped or the casing is damaged, turn the monitor off and unplug
the power cord. Then contact the Service Center.
The monitor may malfunction, causing an electric shock or fire.
Disconnect the plug from the outlet during storms or lightening or if it is not used for a
long period of time.
Failure to do so may cause an electric shock or fire.
Do not try to move the monitor by pulling only the wire or the signal cable.
This may cause a breakdown, electric shock or fire due to damage to the cable.
Do not move the monitor right or left by pulling only the wire or the signal cable.
This may cause a breakdown, electric shock or fire due to damage to the cable.
Do not cover the vents on the monitor cabinet.
Bad ventilation may cause a breakdown or fire.
Do not place water containers, chemical products or small metal objects on the
monitor.
This may cause malfunction, an electric shock or fire.
If a foreign substance enters the monitor, unplug the power cord and contact the
Service Center.
Keep the product away from combustible chemical sprays or inflammable
substances.
This may cause an explosion or fire.
Never insert anything metallic into the monitor openings.
This may cause an electric shock, fire or injury.
Do not insert metal objects such as chopsticks, wire and gimlet or inflammable
objects such as paper and match into the vent, headphone port or AV ports.
It may cause a fire or an electric shock.
If an alien substances or water flows into the product, turn the product off, unplug
the power connector from the wall outlet and contact Service Center.
If you view a fixed screen for an extended period of time, residual image or blurriness
may appear.
Change the mode to energy save or set a screensaver to moving picture when
you need to be away from the monitor for an extended period of time.
Adjust the resolution and frequency to the levels appropriate for the model.
Inappropriate resolution may cause undesirable picture quality.
17 inch (43 cm) - 1280 x 1024
Keep all power adaptors apart.
Failure to do so may cause fire.
Keep power adaptor away from any other heat source.
Failure to do so may cause fire.
Remove and discard vinyl bag from power adaptor before use.
Failure to do so may cause fire.
Always keep power adaptor in well-ventilated area.
Be careful that adaptor should not be in contact with water and therefore not be wet.
This may cause malfunction, an electric shock or fire.
Do not use adaptor by the waterside or outside particularly when it rains or snows.
Be careful that adaptor should not be wet while cleaning floor with water.
Watching the monitor continuously at a too close angle may result in eyesight
damage.
To ease eye strain, take at least a five-minute break after every hour of using the
monitor.
Do not install the product on an unstable, uneven surface or a location prone to
vibrations.
Dropping the product may cause damage to the product or personal injury.
Using the product in a location prone to vibrations may shorten the lifetime of the
product or may catch fire.
When moving the monitor, turn off and unplug the power cord. Make sure that all
cables, including the antenna cable and cables connected to other devices, are
disconnected before moving the monitor.
Failure to disconnect a cable may damage it and lead to fire or an electric shock.
Place the product out of children's reach, as they could damage it by hanging onto it.
A falling product could cause physical damage even death.
When not using the product for an extended time period, keep the product
unplugged.
Otherwise, this may cause heat emission from the accumulated dirt or degraded
insulation, leading to electric shock or fire.
Do not place children's favorite objects (or anything else that may be tempting) on the
product.
Children may try to climb on the product to retrieve an object.
The product could fall, causing physical damage or even death.
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment) - Europe only
(Applicable in the European Union and other European countries with
separate collection systems)
This marking shown on the product or its literature, indicates that it should not
be disposed with other household wastes at the end of its working life. To
prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this
product, or their local government office, for details of where and how they
can take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and
conditions of the purchase contract. This product should not be mixed with
other commercial wastes for disposal.
PRODUCT INFORMATION (Image Retention Free)
LCD Monitors and TVs may have image retention when switching from one image to another
especially after displaying a stationary image for a long time.
This guide is to demonstrate correct usage of LCD products in order to protect them from Image
retention.
What is Image retention ?
During normal operation of a LCD panel, pixel image retention doesn't occur. However,
if the same image is displayed for a long time, a slight difference in electric charge
accumulates between the two electrodes which encase the liquid crystal. This may
cause the liquid crystal to build up in a certain areas of the display. Thus, the previous
image is retained when switching to a new video image. All display products, including
LCD,are subject to image retention. This is not a product defect.
Please follow the suggestions below to protect your LCD from image retention
Power Off, Screen Saver, or Power Save Mode
Ex)
z Turn the power off when using a stationary pattern.
- Turn the power off for 4 hours after 24 hours in use
- Turn the power off for 2 hours after 12 hours in use
z Use a Screen saver if possible
- Screen saver in one color or a moving image is recommended.
z Set the Monitor to power off with the PC Display Properties Power Scheme.
Suggestions for specific applications
Ex) Airports, Transit Stations, Stock Markets, Banks, and Controlling Systems
We recommend that you follow set up of your display system program as below:
Display Information together with Logo or Moving image cycle.
Ex) Cycle : Display Information for 1 hour followed by a
Display Logo or moving image for 1 minute.
Change the Color Information periodically (Use 2 different colors).
Ex) Rotate the Color Information with 2 colors every 30 minutes.
Avoid using a combination of characters and background color with large
difference in luminance.
Avoid using Grey colors, which can cause Image retention easily.
Avoid: Colors with big difference in luminance (Black & White, Grey)
Ex)
z
Recommended settings: Bright colors with little difference in luminance
- Change the characters color and background color every 30 minutes
Ex)
z
- Every 30 minutes, change the characters with movement.
Ex)
The best way to protect your monitor from Image retention is to set your PC or
System to operate a Screen Saver program when you are not using it.
Image retention may not occur when a LCD panel is operated under normal conditions.
Normal conditions are defined as continuously changing video patterns. When the LCD
panel is operated for a long time with a fixed pattern (-over 12 hours-), there may be
slight difference in voltage between electrodes that work the liquid crystal (LC) in a
pixel. The voltage difference between electrodes increases with time, forcing the liquid
crystal to lean. When this occurs, the previous image may be seen when the pattern is
changed.
To prevent this, the accumulated voltage difference must be decreased.
Our LCD Monitor satisfies ISO13406-2 Pixel fault Class II
Features
What is a Tablet Monitor?
A Graphics Drawing Tablet is used for sketching new images or tracing existing images. The user
makes contact with the tablet using a wired or wireless pen or puck.
If a user draws a drawing with a pen or puck, the screen pointer draws the corresponding image.
Since a puck can pinpoint the edge or terminal precisely using the cross hairs viewable through the
transparent lens, it is preferred by users who draw precise scientific drawings. The tablet may be
custom made so that the buttons are located on the exterior and the user can select menus and
functions by pressing the buttons.
When the user draws a drawing or traces an image with the tablet, a series of x and y coordinates
representing the intermediate or terminal points are recorded. The tablet is also called a Graphics
Tablet, a Digitizer Tablet or an Electronic Tablet.
Product Features
A monitor which provides the tablet function that enables users to open the graphics tool on the
screen and directly draw images or letters on the screen.
Easy switching between the tablet and a general monitor.
A double folding stand to provide the optimal environment for using both the tablet and the monitor.
D-Sub Out port support for connecting directly with a projector or a wide screen display device.
MagicContrast : Supports a contrast of up to 700:1 for deeper color tones.
MagicSpeed : Offers a clear image with no afterimages by supporting a fast response rate of 8 ms.
MagicStand : Allows users to adjust the height of the monitor for user convenience.
Applications
For educational purposes, presentations and meetings.
Direct input to the screen while giving a lecture or during a presentation → Easy emphasis and
recording during a presentation
Use of a wide screen like a blackboard → Easy writing and maintenance
Enjoyable at Home
Easily create personal content such as drawings, diaries, etc.
Easily cut, paste and decorate using program such as Photoshop or Illustrator
Educational fun for children (coloring and drawing)
Appropriate for Experts
Graphic Designers, CAD/CAM Designers and 3D Animators
→ Provides a better drawing and editing environment than an electronic pen or digitizer
Cartoonists and Illustrators
→ Resource-saving since it does not require paper, pen or scanner - easy drawing and editing.
Package Contents
Please make sure the following items are included with your monitor.
If any items are missing, contact your dealer.
Contact a local dealer to buy optional items.
Unpacking
Monitor
Manual
Quick Setup Guide
Warranty Card
(Not available in all
locations)
User's Guide, Monitor Driver,
Natural Color software,
MagicTune™ software,
MagicRotation software,
Tableau software
Cable
Power Cord
DC Adaptor
Others
Electronic Pen
Electronic Pen Charger
Pen Lead (2)
Cleaning Cloth
Sold separately
D-sub Cable
Your Monitor
Front
MENU button [ ]
Opens the OSD menu. Also use to exit the OSD menu or return to the
previous menu.
MagicBright™ button
[ ]
MagicBright™ is a new feature providing optimum viewing
environment depending on the contents of the image you are
watching. Currently six different modes are available: Custom, Text,
Internet, Game, Sport and Movie. Each mode has its own preconfigured brightness value. You can easily select one of six settings
by simply pressing MagicBright™ control button.
1) Custom
Although the values are carefully chosen by our engineers, the
pre-configured values may not be comfortable to your eyes
depending on your taste.
If this is the case, adjust the brightness and contrast by using the
OSD menu.
2) Text
For documentations or works involving heavy text.
3) Internet
For working with a mixture of images such as text and graphics.
4) Game
For watching motion pictures such as a game.
5) Sport
For watching motion pictures such as a sport.
6) Movie
For watching motion pictures such as a DVD or Video CD.
>> Click here to see an animation clip
Brightness button [ ]
When OSD is not on the screen, push the button to adjust brightness.
>> Click here to see an animation clip
Adjust buttons [
Adjust items in the menu.
]
Enter button [ ]
Activates a highlighted menu item.
AUTO button
Use this button for auto adjustment.
>> Click here to see an animation clip
Power button [ ]
Use this button for turn the monitor on and off.
Power indicator
This light glows green during normal operation, and blinks green once
as the monitor saves your adjustments.
Signal Button
Press to use the Tablet function.
Pressing this button again, will return the mode to normal monitor
functions.
See PowerSaver described in the manual for further information regarding power saving
functions. For energy conservation, turn your monitor OFF when it is not needed, or
when leaving it unattended for long periods.
Rear
The configuration at the back of the monitor may vary from product to product.
PC Connection Port
RGB OUT Port
To purchase a cable, contact the nearest Service
Center.
RGB IN + USB Port
It is installed on your product. To purchase an
additional cable, contact the nearest Service
Center.
Separating the Cable
Connecting the Cable
DC 14V Connection Port
This product supports both 110V and 220V.
(The voltage is automatically selected by the DC
Adaptor.)
After connecting the cables, connect the power cord to
the wall outlet.
DC OUT Port
Connect the electronic pen charger.
Kensington Lock
The Kensington lock is a device used to physically fix
the system when using it in a public place.
The locking device has to be purchased separately.
For using a locking device, contact where you
purchase it.
See Connecting Cables for further information regarding cable connections.
Connecting Cables
Connect the power cord to the DC power supply and to the 220V or 110V wall outlet.
(The voltage is automatically selected by the power supply.)
To use the D-Sub (analog) output through another device (monitor, TV, projector, etc.)
- Connect the RGB OUT port of the monitor and the D-Sub port of another device using the D-Sub
cable.
[RGB OUT]
When the graphics card supports D-Sub (analog) output
- Connect the RGB IN + USB port of the monitor and the D-Sub port and USB port of the computer
using the Tableau Signal Cable.
If the USB port of the computer is not connected, even though the picture is displayed on the screen,
the position of the electronic pen is not recognized.
[RGB IN + USB]
Using Macintosh
- Connect the monitor and the Macintosh computer using the computer connection cable (Tableau
Signal Cable).
If you are using an old model Macintosh, connect the monitor and the Macintosh using a Macintosh
adaptor (sold separately).
If the monitor and the computer are connected, you can turn them on and use them.
Using the Stand
Using the Tablet
Press the Signal button to activate it.
(The buttons are raised when the Tablet function is turned on.)
Pull the monitor back to a comfortable angle for using it as a tablet.
Separate the pen from the pen holder.
You can perform necessary operations by running a graphics or word processing
software.
To stop using the monitor as a tablet and to use the monitor as a normal monitor, press
the two signal buttons.
(The buttons are pushed down, when the Tablet function is turned off.)
Using the Electronic Pen
About the Electronic Pen
Warning: There is a danger of overheating, fire or explosion.
If put into a fire, heated, shocked or punctured
If children or pets make oral contact with the pen.
If submerged in water or if the battery terminals come into contact with a necklace or any other metal
Use only the charger specified in the User Manual.
Pen Tip
Switch
This part makes contact with the screen and plays the role of the left mouse button.
Press the pen once lightly on the screen for a click and press the pen twice for a
double-click operation.
Signal
Transmitter
This part transmits the signal and notifies its position.
Pen Switch
Plays the role of the right mouse button.
Charge
LED
Red means the charge is not complete.
Green means the charge is completed.
Pen Power
Switch
The switch used to turn the pen on or off.
Charge Port This part is connected to the Electronic Pen Charger. The electronic pen is charged if it
is connected to the charger when the monitor power is connected.
Electronic Pen Charger
When connecting the charger connection port to the monitor's DC OUT port, the
charger LED turns orange, red and then green in this order, and is turned off
indicating that the charge is ready.
While the electronic pen is inserted into the charger, the charger LED is red when
the pen is being charged, and turns green when the pen is fully charged.
Precautions when Using the Electronic Pen
Use the electronic pen keeping it as perpendicular (90°) to the screen as possible.
To use the electronic pen at another angle to the screen surface run the Mouse
Pointer Position Adjustment.
When using the electronic pen, do not cover the Signal Transmitter part with your
hand.
Since the Signal Transmitter has to transmit ultrasonic waves and the Signal
Button has to receive the signal to operate properly, if your hand covers the
transmitter, the precise position may not be recognized.
Please avoid using noisy home appliances such as a dryer or shaver when using the
electronic pen.
Since the Signal Transmitter transmits ultrasonic waves to send the current
position, external noise may cause errors in recognizing the position.
Maintenance and Replacement of the Electronic Pen
Maintenance of
Clean with a soft cloth damped with the "recommended cleaning solution".
the Pen Tip
Replacing the
Pen Lead
z
If the recommended cleaning solution is not available, dilute a cleaning
solution with water at a ratio of 1:10.
As the pen is used, the pen tip will become worn out.
If the abrasions are severe or you experiencing difficulties when using it, replace the
pen lead.
To purchase a pen lead, contact the nearest Service Center.
If the pen tip is worn and a sharp part appears at the tip, it may damage the
screen.
Replace the pen lead periodically.
Removing the Pen Lead
Installing the Pen Lead
Using Other Stands
Pivot Stand
When pivoting the screen, slant the screen more than 45 degrees (approximately 90
degrees) before pivoting the screen.
Installing the Stand
Optional Products
Bracket (For wall mount)
Bracket (For main body)
Anchors (3)
Screws (3)
(For wall mount)
Screws (4)
To purchase an optional product, contact a Samsung Electronics Service Center.
Installing the Bracket (wall mount)
Bracket (main body) Installation Method 1
Fold the monitor stand and place the bracket (main body) at the bottom of the stand. Align the groove
of the bracket (main body) and the groove of the monitor stand
and fix them firmly with 2 screws.
Bracket (main body) Installation Method 2
Fold the monitor stand and rotate it so that the cable connection ports face the floor. Place the
bracket (main body) at the bottom of the stand. Align the groove of the bracket (main body) and the
groove of the monitor stand
and fix them firmly with 4 screws.
Connecting Other Stands
The size of the stand installation surface of the monitor is 75mm x 75mm and is
compatible with the VESA standard.
Stand Installation Surface
Stand
Align the groove of the connection part of the monitor stand and the groove of the stand (for the arm
rest, wall mount or other connection stands) and fix them firmly with the 4 screws.
When installed to the wall
When installed by Bracket (main body) Installation Method 1
When installed by Bracket (main body) Installation Method 2
Tableau
Program Installation Procedures
Insert the Tableau Installation CD into the CD-ROM drive.
Click on the Tableau Setup program.
If the Installation Wizard screen appears, click on the 'Next' button.
Enter the user information and click on 'Next'.
Click on 'Install'.
The installation progress screen appears.
Click on 'Finish'.
When the installation is completed, the Tableau shortcut icon is created on the Desktop.
The Tableau icon [
] is also created in the Taskbar (System Tray).
Click on the Tableau icon [
] and select a Tableau menu.
Menus
When clicking the Tableau icon [
], the Tableau menu window appears.
Mouse pointer positional adjustment menu.
Tableau program properties.
Select to exit the Tableau program.
Mouse Pointer Positional Adjustment
Mouse Pointer Positional Adjustment
Fix the electronic pen tip to the screen and you can adjust the mouse pointer position to a
comfortable position using the keyboard.
Menu and Toolbars
When locating the pen tip at the center, you can adjust the mouse pointer position more easily.
Press the 'ESC' key on the keyboard to cancel the settings and close the window.
Press the 'Enter' key on the keyboard to save the settings and close the window.
You can adjust the position by using the direction keys on the keyboard.
Monitor Driver
When prompted by the operating system for the monitor driver, insert the CD-ROM included with this
monitor. Driver installation is slightly different from one operating system to another. Follow the
directions appropriate for the operating system you have.
Prepare a blank disk and download the driver program file at the Internet web site shown here.
Internet web site :http://www.samsung.com/ (Worldwide)
http://www.samsung.com/monitor (U.S.A)
http://www.sec.co.kr/monitor (Korea)
http://www.samsungmonitor.com.cn/ (China)
Installing the Monitor Driver (Automatic)
Windows ME
Insert CD into the CD-ROM drive.
Click "Windows ME Driver".
Choose your monitor model in the model list, then click the "OK" button.
Click the "Install" button in the "Warning" window.
Monitor driver installation is completed.
Windows XP/2000
Insert CD into the CD-ROM drive.
Click "Windows XP/2000 Driver".
Choose your monitor model in the model list, then click the "OK" button.
If you can see following message window, then click the "Continue Anyway" button. Then click
"OK" button.
This monitor driver is under certifying MS logo, and this installation don't damage your
system.
The certified driver will be posted on Samsung Monitor Homepage
http://www.samsung.com/
Monitor driver installation is completed.
Installing the Monitor Driver (Manual)
Windows XP | Windows 2000 | Windows ME | Windows NT | Linux
Microsoft® Windows® XP Operating System
Insert CD into the CD-ROM drive.
Click "Start" → "Control Panel" then click the "Appearance and Themes" icon.
Click "Display" icon and choose the "Settings" tab then click "Advanced...".
Click the "Properties" button on the "Monitor" tab and select "Driver" tab.
Click "Update Driver..." and select "Install from a list or..." then click "Next" button.
Select "Don't search ,I will..." then click "Next" and then click "Have disk".
Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model
list and click the "Next" button.
If you can see following "Message" window, then click the "Continue Anyway" button. Then click
"OK" button.
This monitor driver is under certifying MS logo, and this installation don't damage your
system.
The certified driver will be posted on Samsung Monitor homepage
http://www.samsung.com/
Click the "Close" button then click "OK" button continually.
Monitor driver installation is completed.
Microsoft® Windows® 2000 Operating System
When you can see "Digital Signature Not Found" on your monitor, follow these steps.
Choose "OK" button on the "Insert disk" window.
Click the "Browse" button on the "File Needed" window.
Choose A:(D:\Driver) then click the "Open" button and then click "OK" button.
How to install
Click "Start" , "Setting" , "Control Panel".
Double click the "Display" icon.
Select the "Settings" tab and click "Advanced Properties" button.
Choose "Monitor".
Case1 : If the "Properties" button is inactive, it means your monitor is properly configured. Please
stop installation
Case2 : If the "Properties" button is active, click the "Properties" button then follow next steps
continually.
Click "Driver" and then click on "Update Driver..." then click on the "Next" button.
Choose "Display a list of the known drivers for this device so that I can choose a specific driver"
then click "Next" and then click "Have disk".
Click the "Browse" button then choose A:(D:\Driver).
Click the "Open" button, then click "OK" button.
Choose your monitor model and click the "Next" button then click "Next" button.
Click the "Finish" button then the "Close" button.
If you can see the "Digital Signature Not Found" window then click the "Yes" button. And click the
"Finish" button then the "Close" button.
Microsoft® Windows® Millennium Operating System
Click "Start" , "Setting" , "Control Panel".
Double click the "Display" icon.
Select the "Settings" tab and click "Advanced Properties" button.
Select the "Monitor" tab.
Click the "Change" button in the "Monitor Type" area.
Choose "Specify the location of the driver".
Choose "Display a list of all the driver in a specific location..." then click "Next" button.
Click the "Have Disk" button.
Specify A:\(D:\driver) then click "OK" button.
Select "Show all devices" and choose the monitor that corresponds to the one you connected to
your computer and click "OK".
Continue choosing "Close" button and "OK" button until you close the Display Properties dialogue
box.
Microsoft® Windows® NT Operating System
Click "Start", "Settings", "Control Panel", and then double-click "Display" icon.
In Display Registration Information window, click Settings Tab and then click "All Display Modes".
Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency) and
then click "OK".
Click "Apply" button if you see the screen working normally after clicking "Test". If the screen is
not normal, change to a different mode (lower mode of resolution, colors or frequency).
If there is no Mode at All Display Modes, select the level of resolution and vertical
frequency by referring to the Preset Timing Modes in the user guide.
Linux Operating System
To execute X-Window, you need to make the X86Config file, which is a type of system setting file.
Press "Enter" at the first and the second screen after executing the X86Config file.
The third screen is for setting your mouse.
Set a mouse for your computer.
The next screen is for selecting a keyboard.
Set a Keyboard for your computer.
The next screen is for setting your monitor.
First of all, set a horizontal frequency for your monitor. (You can enter the frequency directly.)
Set a vertical frequency for your monitor. (You can enter the frequency directly.)
"Enter" the model name of your monitor. This information will not affect the actual execution of XWindow.
You have finished setting up your monitor.
Execute X-Window after setting other requested hardware.
Natural Color
Natural Color Software Program
One of the recent problems in using a computer is that the color of the images printed out by a printer
or other images scanned by a scanner or a digital camera are not the same as those shown on the
monitor. The Natural Color S/W is the very solution for this problem. It is a color administration
system developed by Samsung Electronics in association with Korea Electronics &
Telecommunications Research Institute (ETRI). This system is available only for Samsung monitors
and makes the color of the images on the monitor the same as the printed or scanned images.
For more information, refer to Help (F1) in the software program.
How to install the Natural Color software
Insert the CD included with the Samsung monitor into the CD-ROM Drive. Then, the initial screen of
the program Natural Color will be executed. Click Natural Color on the initial screen to install the
Natural Color software.
To install the program manually, insert the CD included with the Samsung monitor into the CD-ROM
Drive, click the [Start] button of Windows and then select [Run...].
Enter D:\color\eng\setup.exe and then press the [Enter] key.
(If the drive where the CD is inserted is not D:\, enter the applicable drive.)
How to delete the Natural Color software program
Select "Setting/Control Panel" on the "Start" menu and then double-click "Add/Delete a program".
Select Natural Color from the list and then click the "Add/Delete" button.
Overview
| Installation
| OSD Mode
| Color Calibration
| Uninstall
| Troubleshooting
Overview
What is MagicTune™?
Monitor performance can vary due to the graphics card, host computer lighting conditions and other
environmental factors. In order to get the best image on a monitor requires you to adjust it for your unique
setting. Unfortunately, the manual controls available to tune the image often prove to be challenging.
Proper adjustment (tuning) requires an easy to use program that goes through a step-by-step process to
obtain the best overall picture quality.
In most cases even simple adjustments to Brightness, or Contrast require navigation of the multi-level, onscreen display (OSD) menus that are not easy to understand. Furthermore, there is no feedback to assist
in correctly setting the controls of the monitor. MagicTune™ is a software utility that guides you through
the tuning process with easy to understand instructions and back ground patterns designed for each
monitor control. The display settings for each user can be saved, providing an easy way to select display
characteristics in a multi-user environme or having a single user have multiple defined presets based on
content and ambient lighting.
Basic Functionality
MagicTune™ is a software utility that allows monitor adjustment and color tuning using the Display Data
Channel Command Interface (DDC/CI) protocol. All adjustments to the display are controlled via software
to eliminate the need to use the monitor on-screen display (OSD).
MagicTune™ supports Windows™ 98 SE, Me, 2000, XP Home, and XP Professional.
It is recommended using MagicTune™ in Windows™ 2000 or later.
MagicTune™ allows for quick accurate tuning of the display with the ability to easily save and use monitor
configurations that are best suited for you.
OSD Mode
The OSD mode allows easy adjustment of monitor settings without taking pre-defined steps. You can
access the desired menu item to set with ease.
Overview
| Installation
| OSD Mode
| Color Calibration
Installation
1. Insert the installation CD into the CD-ROM drive.
2. Click the MagicTune™ installation file.
| Uninstall
| Troubleshooting
3. Select installation Language, Click "Next".
4. When the Installation Shield Wizard window appears, click "Next."
5. Select "I agree to the terms of the license agreement" to accept the terms of use.
6. Choose a folder to install the MagicTune™ program.
7. Click "Install."
8. The "Installation Status" window appears.
9. Click "Finish."
10. When the installation is complete, the MagicTune™ executable icon appears on your desktop.
Double-click the icon to start the program.
MagicTune™ execution icon may not appear depending on specification
of computer system or monitor.
If that happens, press F5 Key.
Installation Problems
The installation of MagicTune™ can be affected by such factors as the video card, motherboard and the
network environment.
See "Troubleshooting" if you have trouble during installation.
System Requirements
OS
z
z
z
z
z
Windows™ 98 SE
Windows™ Me
Windows™ 2000
Windows™ XP Home Edition
Windows™ XP Professional
It is recommended using MagicTune™ in Windows™ 2000
or later.
Hardware
z
z
32MB Memory above
25MB Hard disk space above
* For more information, visit the MagicTune™ website.
Overview
| Installation
| OSD Modes
| Color Calibration
| Uninstall
| Troubleshooting
MagicTune™ allows for quick accurate tuning of the display with the ability to easily save and
use monitor configurations that are best suited for you.
z
z
z
OSD mode may appear inconsistent with the explanation in guidance book
depending on specification of each monitor.
When Pivot is functioning, part of MagicTune™ Program may not operate
normally.
AutoRotation : AutoRotation will automatically pivots the monitor to 0, 90,
180degrees when you pivots the monitor.
To execute Rotation, it should be done as below.
Please install both of Rotation program and MagicTune™ 3.6 in your PC.
z Launch MagicTune™ 3.6
z Option → Preference → click the small box as "V" in enable task tray menu.
z
z
z
MagicTune™ control mode will be different according to monitor models.
The permitted angle of rotation of the monitor is determined by the model of the
monitor.
OSD Mode
The OSD mode makes the adjustment of settings on all monitors easy. When selected , each tab on top of
the control window displays the general descriptions of the sub-menu items for adjustment.
When selected, each tab displays a list of menus. For quick adjustment of the monitor settings, the OSD
mode allows easy and convenient access to all tabs and sub-menu items.
Button Tab Definition
OK
Applies any changes made and exits MagicTune™.
Reset
Restores the display settings to the factory settings.
Cancel
Exits MagicTune™ without applying the changes made. If you have not made any
changes in the control window, clicking "Cancel" does not cause any actions.
Picture Tab Definition
Allows the user to adjust the screen settings to the desired values.
Brightness
Makes the entire screen brighter or darker. The detailed data of the images in the dark
areas can be lost if the brightness is not adjusted to the proper level. Adjust the
brightness for best viewing conditions.
Contrast
Adjusts the difference in brightness between the bright and dark areas on screen.
Determines the crispness of the images.
Resolution
Lists all display resolutions supported by the program.
MagicBright™ is a new feature providing the optimum viewing environment depending
on the contents of the image you are watching. Currently six different modes are
available: Text, Internet,Game, Sport, Movie and Custom. Each mode has its own preconfigured brightness value. You can easily select one of six settings by simply pressing
MagicBright control buttons.
1.
2.
3.
4.
5.
6.
MagicBright™
Text: For documentations or works involving heavy text.
Internet: For working with a mixture of images such as text and graphics.
Game : For watching motion pictures such as a Game.
Sport : For watching motion pictures such as a Sport.
Movie: For watching motion pictures such as a DVD or Video CD.
Custom: Although the values are carefully chosen by our engineers, the preconfigured values may not be comfortable to your eyes depending on your taste.
If this is the case, adjust the Brightness and Contrast by using the OSD menu.
MagicBright control mode will be different according to monitor models.
Some monitor will only support Four modes(Text, Internet, Entertain,
Custom)
Color Tab Definition
Adjusts the "warmth" of the monitor background or image color.
MagicColor and Gamma will be shown only in the monitor that supports
these functions.
The tone of the color can be changed.
z
z
Warm2 - Warm1 - Cool 1 - Cool 2 - Cool 3 - Cool 4 - Cool 5 - Cool 6 - Cool 7
Off
Color Tone
Color Tone mode will be different according to monitor models.
Some monitor will only support Four modes( Warm, Normal, Cool,
Custom)
Color Control
Adjusts of the monitor image color.
You can change the monitor color to your desired color.
z
Calibration
R- G - B
The process through which the colors of your choice are optimized and maintained. You
will find MagicTune™ extremely useful if you are one of those who wish to view images
with their full details accurately reproduced - including web images and ones produced
by a digital camera or scanner.
MagicColor is a new technology that Samsung has exclusively developed to improve
digital image and to display natural color more clearly without disturbing image quality.
1. OFF : Returns to the original mode.
2. DEMO : The screen before applying MagicColor appears on the right and the
screen after applying MagicColor appears on the left.
3. Full : Displays not only vivid natural color but also more realistic natural skin color
with clearness.
4. Intelligent : Displays vivid natural color with clearness.
5. MagicZone
{ The MagicZone ensures the clear and sharp display of animated
multimedia or photo images by enhancing the brightness, sharpness,
saturation, Hue of a certain area on the screen. This offers an easy-to-use
interface that highlights the video-playing portion of your multimedia
program by automatically detecting and highlight the desired area by
dragging.
)and it is necessary to de-activate it
{ When the mouse cursor is activated(
to use it for other tasks, right click your mouse, or put the activated cursor (
)on the taskbar and click. When de-activated, the icon on the screen
changes back to the one shown before activation.
{
{
{
Especially, MagicZone is appropriate to using the moving picture.
Auto Detect : If you run the Movie in some players, MagicZone will
automatically get the play screen highlighted (it will be supported in players
of Gom, Adrenalin, KCP, Window Media, and Power DVD etc., )Some other
players also can be highlighted but could have some problems.
Tusk menu
Adjust the tint of the color.
HUE
Saturation Adjusts the color saturation.
Brightness Adjusts the Brightness.
MagicColor
Sharpness
Adjusts the difference between the lightest and darkest areas
of the display.
Zone Off
Turn off the zone that you have captured.
Reset
Returns to the the default setting that vendor has set.
z
Depending on the monitor models Color Control, Sharpness,
Contrast, Color Tone, Brightness will not be adjustable in
MagicColor mode of Full and Intelligent.
z
MagicTune™ will be disappear if you excute MagicZone, and
closing the MagicZone after adjusting, will show the MagicTune™
again.
(System Tray is Unhecked)
MagicTune™ will be disappear if you excute MagicZone, and
closing the MagicZone after adjusting. will not show MagicTune™
again.
(System Tray is Checked)
z
MagicColor mode will be different according to monitor models.
MagicZone mode will show if the monitor supports the function.
Gamma correction changes the luminance of the colors with intermediate luminance.
Gamma
Gamma mode will be different according to monitor models. Some
monitor will only support Three modes( Mode1, Mode2, Mode3)
Image Tab Definition
Adjusts the Fine , Coarse and Position values.
z
Image Setup
z
z
Fine : Removes noise such as horizontal stripes.
If the noise persists even after Fine tuning, repeat it after adjusting the frequency
(clock speed).
Coarse : Removes noise such as vertical stripes.
Coarse adjustment may move the screen image area.
You may relocate it to the center using the Horizontal Control menu.
Auto Setup : Auto adjustment allows the monitor to self-adjust to the incoming
video signal. The values of fine, coarse and position are adjusted automatically.
Position
Adjusts the screen location horizontally and vertically.
Sharpness
Changes the clearance of image.
Option Tab Definition
You can configure MagicTune™ using the following options.
Loads the Preferences Dialog Box. Preferences in use will have an "V" in the check
box. To turn on or off any Preference, position the cursor over the box and click.
Preferences
z
z
Source Select
z
z
Enable task tray menu .
- To access the MagicTune™ menus, click the icon on the [task tray menu].
The menus are not displayed if the [Enable System Tray] is deselected in
[Options] ' [Basic Settings].
Select Language - The language chosen affects only the language of the OSD.
Analog
Digital
Support Tab Definition
Shows the Asset ID and the version number of the program, and allows you to use the Help feature.
Help
Visit the MagicTune™ website or click to open the Help files (User Manual) if you need
any help installing or running MagicTune™. The User Manual opens within a basic
browser window.
Asset ID
you can use the server to control the Client monitor.
(Server program should be installed to use this program as Client)
Version
Overview
User Name
Shows the user name that is registered in PC.
User ID
Shows the user ID that is register in PC.
Server IP
Write down the server IP .
Department
Write down the department.
Location
Write down the location.
Displays the version of MagicTune™.
| Installation
| OSD Mode
| Color Calibration
| Uninstall
| Troubleshooting
Color Calibration
Color Calibration
Color Calibration guides you to get optimal color condition for your monitor.
Proceed following 5steps for getting optimal monitor color condition .
1. Control "Brightness control bar" for matching the brightness of control patch and the brightness of
background pattern
2. When you detect specific color tone on "Control patch", move the control cursor toward to the
direction of the color tone referring to "Color reference Circle".
=> Adjustment is finished properly, you won't detect any color tone on Control patch.
3. When you finish adjustment for step1,Click "Next" button .
4. Repeat 1), 2), 3) procedures for remaining step2 ~ step5.
5. You can easily view the calibration effect through clicking "Preview " button!
How multiple users can use adjusted color values
Definition
When monitor is used by multiple users, color values which are adjusted via Color calibration for each
users can be saved and used. Up to 5 users can use the saved color values.
1. How to save adjusted color values:
Press Next to make it change into Apply and then you can save adjusted color values.
As many as 5 values can be saved.
2. How to apply the saved color values:
Press Multi User button on main screen to select and use one of the saved color values.
Preview
Press "Preview" button on the Color Calibration.
The above picture will be shown.
1. Press "View Calibrated" button to see the calibration effect which you adjusted.
2. Press "View Uncalibrated" button to see the original image.
Overview
| Installation
| OSD Mode
| Color Calibration
| Uninstall
| Troubleshooting
Uninstall
The MagicTune™ program can be removed only by using the "Add or Remove Programs" option of the
Windows™ Control Panel.
Perform the following steps remove MagicTune™.
1. Go to [Task Tray] ' [Start] ' [Settings] and select [Control Panel] in the menu. If the program runs on
Windows™ XP, go to [Control Panel] in the [Start] menu.
2. Click the "Add or Remove Programs" icon in Control Panel.
3. In the "Add or Remove Programs" screen, scroll down to find "MagicTune™." Click on it to highlight it.
4. Click the "Change/Remove" button to remove the program.
5. Click "Yes" to begin the uninstall process.
6. Wait until the "Uninstall Complete" dialog box appears.
Visit the MagicTune™ website for technical support for MagicTune™, FAQs (questions and answers) and
software upgrades.
Overview
| Installation
| OSD Mode
| Color Calibration
| Uninstall
| Troubleshooting
Troubleshooting
The current computing system is not compatible with MagicTune™.
Please press OK and click on the "Shortcut to the MagicTune™ site" to view our home page
for further reference.
An error may occur when your video/graphic card is not in the 'Available' list.
(The latest or oldest video cards may not be compatible.)
Please visit our homepage to see the Troubleshooting section.
An error may occur if the card maker has modified the video card driver or the graphics
chip even when the video card is in the list.
Please visit our homepage to see the Troubleshooting section.
Check if your monitor is manufactured by Samsung.
Products from other manufacturers may cause errors.
Only Samsung products are able to support this feature.
An error may occur even when your monitor is manufactured by Samsung but is out of
date. Check if your monitor is able to support MagicTune™.
This feature is only supported by those monitors that are registered on our homepage.
Check for the monitor before purchasing it as out-of-date models are not supported.
An error occurs when no information on EDID (Extended Display Identification Data)
exists for the current monitor.
This happens when from your desktop, Start → Setup → Control Panel → System →
Hardware → Device Manager → Monitor is selected, the current "Plug-and-play monitor"
is removed and new hardware is searched for but the system couldn't find any "Plug-andplay monitor".
Please visit our homepage to see the Troubleshooting section.
An error occurs when replacing the monitor with a new one when the system power is off
but the system has not been restarted.
Please restart the system each time the monitor is replaced before using MagicTune™.
An error occurs when the video card driver is not installed properly.
This happens when the current video card list is not displayed normally. You can check
this via Start → Setup → System → Hardware → Device Manager → Display Adapter.
Visit the video card maker's homepage and download and install the latest driver.
For more information about the video card, contact the card manufacturer.
To ensure normal operation, please restart your system.
An error occurs when the system is not restarted after installing MagicTune™.
(This is for Win98SE and WinMe only.)
Restart the system before use.
For the best performance of MagicTune™, adjust to the optimal resolution.
Refer to the User Guide for the optimal resolution.
If you do not adjust to the optimal resolution and perform Color Calibration, the monitor
cannot be adjusted to the optimal condition.
Refer to the manual for the optimal resolution.
This video card does not support MagicTune™.
Please install a new video card driver.
An error occurs when the video card driver is not installed properly.
This happens when the current video card list is not displayed normally. You can check
this from Start → Setup → System → Hardware → Device Manager → Display Adapter.
Visit the video card manufacturer's homepage and download and install the latest
driver.
For more information about the video card, contact the card manufacturer.
As the Highlight program uses the communication lines,
please exit the Highlight program before you can access MagicTune™.
Some of Samsung CDT monitors support the Highlight feature.
When using both the Highlight feature and MagicTune™ simultaneously, conflicts occur,
which cause errors.
Make sure to turn OFF Highlight before using MagicTune™.
Troubleshooting
z
MagicTune™ may not work in case monitor is replaced or driver of graphic card is updated while
MagicTune™ is operating. If so, please restart the system.
Symptom
Check when
MagicTune™ does not
function properly.
Check List
MagicTune™ feature is
found only on PC (VGA)
with Window OS that
supports Plug and Play.
Solutions
* To check whether your PC is available for
MagicTune™ feature, follow the
steps below (When Windows™ is XP);
Control Panel → Performance and Maintenance →
System → Hardware → Device Manager →
Monitors → After deleting Plug and Play monitor,
find 'Plug and Play monitor' by searching new
Hardware.
MagicTune™ is an additional software for the
monitor. Some graphic cards may not support your
monitor. When you have a problem with the
graphic card, visit our website to check the
compatible graphic card list provided.
http://www.samsung.com/monitor/magicTune
MagicTune™ doesn't
work properly.
z
z
Have you changed your
PC or video graphic
card?
Download the latest program. The program can be
downloaded
http://www.samsung.com/monitor/magicTune
Visit the MagicTune™ website for technical support for MagicTune™, FAQs (questions and answers) and
software upgrades.
Visit the MagicTune™ website and download the installation software for MagicTune™ MAC.
|
Overview
Installation
|
Interface
|
Uninstall
|
Troubleshooting
Overview
What is MagicRotation?
Traditionally, computer displays allowed the user to view only in landscape mode.
In today's information age, more users need to view documents, web pages, emails, etc. in there day to
day life. These types of applications can be better viewed in portrait mode where the entire contents are
available on the screen. This greatly improves the user's productivity allowing him the flexibility to switch
between landscape and portrait modes.
The MagicRotation Software from Samsung Electronics, Inc. provides the user with a rotation feature (0,
90, 180, 270 orientation) that facilitates the optimum utilization of computer display screen, better viewing
and improved user productivity.
Basic Function
MagicRotation will support Windows™ 98 SE, Me, NT 4.0, 2000, XP Home and XP Professional.
* Windows™ is registered trademark of Microsoft Corporation,Inc.
Overview
|
Installation
|
Interface
Installation
1. Insert the installation CD into the CD-ROM drive.
2. Click the MagicRotation installation file.
3. Select installation Language, Click "Next".
|
Uninstall
|
Troubleshooting
4. When the InstallShield Wizard window appears, click "Next."
5. Select "I agree to the terms of the license agreement" to accept the terms of use.
6. Choose a folder to install the MagicRotation program.
7. Click "Install."
8. The "Installation Status" window appears.
9. Click "Finish."
Have to reboot the system in order for the MagicRotation to work properly.
10. When the installation is complete, the MagicRotation executable icon appears on your desktop.
Installation Problems
The installation of MagicRotation can be affected by the factors such as video card, motherboard and the
network environment.
See "Troubleshooting" if you have trouble during installation.
Limitation
1. The "Display Driver" should be properly loaded for the MagicRotation to work properly.
The installed "Display Driver" should be the latest driver supplied by the vendor.
2. If some applications like Windows™ Media Player, Real Player, etc. are not displaying movie files
properly in 90, 180 and 270 orientations then do the following :
{ Close the application.
{ Select the Orientation (90, 180, 270) you want to view the application.
{ Relaunch the application.
In most cases this should fix the problem.
3. User Applications using OpenGL and DirectDraw (3D drawing) will not function as per the
orientation mode selected (90, 180, 270).
e.g. 3D games
4. DOS based applications in Full Screen Mode will not function as per the orientation mode selected
(90, 180, 270).
5. Dual is not supported in Windows™ 98, ME, NT 4.0.
6. MagicRotation does not provide support for 24 bits per pixel (Bit depth/Color Quality).
7. If you are changing your Graphic Card it is recommended that you uninstall the MagicRotation
Software before doing so.
System Requirements
OS
z
z
z
z
z
z
Windows™ 98 SE
Windows™ Me
Windows™ NT 4.0
Windows™ 2000
Windows™ XP Home Edition
Windows™ XP Professional
Hardware
z
z
128MB Memory above(recommended)
25MB Free Hard disk space above
Service Packs
z
z
It is recommended that your System has the latest Service Pack installed.
For Windows™ NT 4.0, it is recommended to install Internet Explorer 5.0 and above with Active
Desktop component.
* For more information, visit the MagicRotation website.
* Windows™ is registered trademark of Microsoft Corporation,Inc.
Overview
z
z
|
Installation
|
|
Interface
Uninstall
|
Troubleshooting
When Rotation is functioning, part of MagicTune™ Program may not operate normally.
AutoRotation : AutoRotation will automatically AutoRotations the monitor to 0, 90,
180degrees when you AutoRotations the monitor.
To execute AutoRotation, it should be done as below.
z
z
z
Please install both of Rotation program and MagicTune™ 3.6 in your PC.
Launch MagicTune™ 3.6
Option → Preference → click the small box as "V" in enable task tray menu.
* The angle of rotatation may vary depending on your monitor spec.
Interface
The Menu on task bar
Menu pop up at the mouse right button click.
Rotate : Display will get rotated by the unit of 90 degree
Rotate to 0 : Display will get rotated to 0 degree from the current angle of rotation.
Rotate to 90 : Display will get rotated to 90 degree from the current angle of rotation.
Rotate to 180 : Display will get rotated to 180 degree from the current angle of rotation.
Rotate to 270 : Display will get rotated to 270 degree from the current angle of rotation.
Hot key : Hot Keys are available by default and can be changed by user.
It can be assigned by user directly with keyboard after changing the existing HotKey.
User can create the hot key with the combination of Shift, Ctrl, Alt and general keys.
In case only general key is pressed, it will be assigned in the form of Alt+general key.
Help : It shows the HELP of MagicRotation program.
About : It shows the version and copyright of MagicRotation program.
Exit : It exits from MagicRotation program.
Overview
|
Installation
|
Interface
|
Uninstall
|
Troubleshooting
Uninstall
The MagicRotation program can be removed only by using the "Add/Remove Programs" option of the
Windows™ Control Panel.
Perform the following steps to remove MagicRotation.
1. Go to [Task Tray] ' [Start] ' [Settings] and select [Control Panel] in the menu.
If the program runs on Windows™ XP, go to [Control Panel] in the [Start] menu.
2. Click the "Add/Remove Programs" icon in Control Panel.
3. In the "Add/Remove Programs" screen, scroll down to find "MagicRotation"
Click on it to highlight it.
4. Click the "Change/Remove" button to remove the program.
5. Click "Yes" to begin the uninstall process.
6. Wait until the "Uninstall Complete" dialog box appears.
7. After uninstall restart the system to complete the uninstallation.
Visit the MagicRotation website for technical support for MagicRotation, FAQs (questions and answers) and
software upgrades.
* Windows™ is registered trademark of Microsoft Corporation,Inc.
Overview
|
Installation
|
Interface
|
Uninstall
|
Troubleshooting
Troubleshooting
Before You Call Technical Support
z
MagicRotation Software works with the installed "Display Driver" supplied by your Graphic Card
Vendor to provide screen rotation capabilities. If the installed "Display Driver" is working incorrectly
or has bugs in it, then these bugs would still exist even after MagicRotation Software is installed.
Any incorrect/random behaviour resulting due to problems in the installed "Display Driver" are not
due to MagicRotation Software.
In order to verify if a problem exists in the installed "Display Driver" , you can perform the following
diagonostic steps :
1. Check if the problem is occuring in both 0 orientation (Landscape mode) and 90 orientation
(Portarit mode).
2. Check if the problem occurs with different color depths (8/16/32 bits per pixel) and different
resolution modes (800 x 600, 1024 x 768).
3. Check if the problem occurs without installing MagicRotation Software.
If the problem is repeating in any/all of the following scenarios then it may be the problem with your
installed "Display Driver" :
In order to correct the problem you need to perform the following steps :
1. Uninstall MagicRotation Software.
2. Obtain the latest "Display Driver" from your Graphic Card Vendor.
The latest "Display Driver" from (ATI, NVIDIA, MATROX, INTEL, etc.) are easily available for
download from their respective websites.
3. Install the latest "Display Driver"
4. Install MagicRotation Software. In most of the cases this should correct the problem.
z
MagicRotation may not work in case monitor is replaced or driver of graphic card is updated while
MagicRotation is operating.
If so, please restart the system.
z
Visit the MagicRotation website for technical support for MagicRotation, FAQs (questions and
answers) and software upgrades.
Control Buttons
[MENU / ] Opens the OSD menu. Also use to exit the OSD menu or return to the
previous menu.
[
] These buttons allow you to adjust items in the menu.
[ ] Press this button to activate a highlighted menu item.
[AUTO] When the 'AUTO' button is pressed, the Auto Adjustment screen appears as
shown in the animated screen on the center.
Direct Functions
AUTO
Menu
Description
When the 'AUTO' button is pressed, the Auto Adjustment screen appears as
shown in the animated screen on the center.
The values of fine, coarse and position are adjusted automatically.
AUTO
To make the automatic adjustment function sharper, execute the 'AUTO' function
while the AUTO PATTERN is on.
If auto adjustment does not work properly, press 'AUTO' button again to adjust
picture with more accuracy.
If you change resolution in the control panel, auto function will be executed
automatically.
OSD Lock & Unlock
Menu
Description
After pushing the "MENU" button more than 5 seconds, OSD function is locked
(unlocked).
OSD Lock & Unlock
You can also adjust the brightness and contrast of the monitor with the
OSD adjustment locking feature.
MagicBright™
Menu
MagicBright™
Description
Push the MagicBright™ button to circle through available preconfigured
modes.
- Six different modes (Custom/Text/Internet/Game/Sport/Movie)
Brightness
Menu
Description
Brightness
When OSD is not on the screen, push the button to adjust brightness.
OSD Function
Picture
Brightness
Contrast
Color
MagicColor
Color Tone
Color Control
Gamma
Image
Coarse
Fine
Sharpness
H-Position
V-Position
OSD
Language
H-Position
V-Position
Transparency
Display Time
Setup
Image Reset
Color Reset
Information
Picture
Menu
Description
You can use the on-screen menus to change the
brightness according to personal preference.
( Not available in MagicColor mode of Full and Intelligent. )
Brightness
Direct Access Feature : When OSD is not on the screen,
push the button to adjust brightness.
>> Click here to see an animation clip
MENU →
Contrast
→
,
→ MENU
You can use the on-screen menus to change the contrast
according to personal preference.
( Not available in MagicColor mode of Full and Intelligent. )
MENU →
Color
→
→
,
→
→
,
→ MENU
Play/Stop
Menu
Description
Play/Stop
MagicColor is a new technology that Samsung has exclusively
developed to improve digital image and to display natural color
more clearly without disturbing image quality.
Off
Demo
Returns to the original mode.
The screen before applying MagicColor appears
on the right and the screen after applying
MagicColor appears on the left.
Full
Displays not only vivid natural color but also
more realistic natural skin color with clearness.
Intelligent Displays vivid natural color with clearness.
MagicZone The MagicZone ensures the clear and sharp
display of animated multimedia or photo images
by enhancing the brightness, sharpness,
saturation, hue of a certain area on the screen.
Especially, MagicZone is appropriate to using
the moving picture.
MagicZone
Hue
This function is to adjust the hue of the
MagicZone.
Saturation
This function is to adjust the saturation of the
MagicZone.
Saturation
Brightness
This function is to adjust the brightness of the
MagicZone.
Brightness
Sharpness
This function is to adjust the sharpness of the
MagicZone.
Sharpness
H-Position
This function is to move the MagicZone
horizontally.
H-Position
V-Position
This function is to move the MagicZone vertically.
V-Position
H-Size
This function is to adjust the horizontal size of the
MagicZone.
H-Size
V-Size
This function is to adjust the vertical size of the
MagicZone.
V-Size
MagicColor
Hue
Color Tone
The tone of the color can be changed and one of four modes
can be selected -Cool, Normal, Warm and Custom.
( Not available in MagicColor mode of Full and Intelligent. )
MENU →
Color Control
,
→
→
,
→
→
,
→ MENU
Adjusts individual Red, Green, Blue color balance. -Red, Green,
Blue
( Not available in MagicColor mode of Full and Intelligent. )
MENU →
,
→
→
,
→
→
,
→
→
,
→ MENU
Gamma correction changes the luminance of the colors with
intermediate luminance.
Gamma
- Mode 1
- Mode 2
- Mode 3
MENU →
,
→
→
,
→
→
,
→ MENU
Image
Menu
Coarse
Description
Removes noise such as vertical stripes.
Coarse adjustment may move the screen image area. You
may relocate it to the center using the horizontal control
menu.
MENU →
Fine
→
→
→
,
→ MENU
Removes noise such as horizontal stripes.
If the noise persists even after fine tuning, repeat it after
adjusting the frequency (clock speed).
MENU →
Sharpness
,
,
→
→
,
→
→
,
→ MENU
Changes the clearance of image.
( Not available in MagicColor mode of Full and
Intelligent. )
MENU →
,
→
→
,
→
→
,
→ MENU
Play/Stop
H-Position
Changes the horizontal position of the monitor's entire
display.
MENU →
V-Position
,
→
→
,
→
→
,
→ MENU
Changes the vertical position of the monitor's entire
display.
MENU →
,
→
→
,
→
→
,
→ MENU
OSD
Menu
Description
You can choose one of eight languages.
Language
The language chosen affects only the language of the OSD. It
has no effect on any software running on the computer.
MENU →
H-Position
→
→
→
,
→ MENU
You can change the horizontal position where the OSD menu
appears on your monitor.
MENU →
V-Position
,
,
→
→
,
→
→
,
→ MENU
You can change the vertical position where the OSD menu
appears on your monitor.
MENU →
,
→
→
,
→
→
,
→ MENU
Change the transparency of the background of the OSD.
Transparency
MENU →
Display Time
,
→
→
,
→
→
,
→ MENU
The menu will be automatically turned off if no adjustments are
made for a certain time period.
You can set the amount of time the menu will wait before it is
turned off.
- 5 Sec, 10 Sec, 20 Sec, 200 Sec
Play/Stop
MENU →
,
→
→
,
→
→
,
→ MENU
Setup
Menu
Image Reset
Description
Image parameters are replaced with the factory default
values.
MENU →
Color Reset
→
→
→
,
→ MENU
Color parameters are replaced with the factory default
values.
MENU →
Information
,
,
→
→
,
→
→
,
→ MENU
Play/Stop
Menu
Description
Shows a video source, display mode on the OSD screen.
Information
MENU →
,
Check List
Before calling for service, check the information in this section to see if you can remedy any problems
yourself. If you do need assistance, please call the phone number on the Information section or contact
your dealer.
Symptom
Check List
Solutions
No images on the
screen.
I cannot turn on the
monitor.
Is the power cord
connected properly?
Check the power cord connection and supply.
Can you see "Check
Signal Cable" on the
screen?
Check the signal cable connection.
If the power is on,
reboot the computer
to see the initial
screen(the login
screen), which can
be seen.
If the initial screen (the login screen) appears, boot the
computer in the applicable mode (the safe mode for
Windows ME/XP/2000) and then change the frequency
of the video card.
(Refer to the Preset Timing Modes)
If the initial screen (the login screen) does not appear,
contact the Service Center or your dealer.
Can you see "Not
Optimum Mode",
"Recommended
Mode 1280 x 1024
60 Hz" on the
screen?
You can see this message when the signal from the
video card exceeds the maximum resolution and
frequency that the monitor can handle properly.
Adjust the maximum resolution and frequency that the
monitor can handle properly.
If the display exceeds SXGA or 75 Hz, a "Not Optimum
Mode", "Recommended Mode 1280 x 1024 60 Hz"
message is displayed. If the display exceeds 85 Hz,
the display will work properly but the "Not Optimum
Mode", "Recommended Mode 1280 x 1024 60 Hz"
message appears for one minute and then disappears.
Please change to the recommended mode during this
one-minute period.
(The message is displayed again if the system is
rebooted.)
I cannot see the On
There is no image on
the screen.
Is the power indicator
on the monitor
blinking at 1 second
intervals?
The monitor is in PowerSaver mode.
Have you locked the
Unlock the OSD by pressing the
Press a key on the keyboard to activate the monitor
and restore the image on the screen.
Screen Display.
On Screen Display
(OSD) Menu to
prevent changes?
[MENU / ] button for at least 5
seconds.
The screen shows
strange colors or
just black and white.
Is the screen
displaying only one
color as if looking at
the screen through a
cellophane paper?
Check the signal cable connection.
Have the screen
colors become
strange after running
a program or due to
a crash between
applications?
Reboot the computer.
Has the video card
been set properly?
Set the video card by referring to the video card
manual.
Have you changed
the video card or the
driver?
Adjust screen image position and size using the OSD.
Have you adjusted
the resolution or
frequency to the
monitor?
Adjust the resolution and frequency at the video card.
(Refer to thePreset Timing Modes).
The screen
suddenly has
become
unbalanced.
Make sure the video card is fully inserted in it's slot.
The screen can be unbalanced due to the cycle of the video card signals.
Readjust Position by referring to the OSD.
The screen is out of
focus or OSD
cannot be adjusted.
Have you adjusted
the resolution or
frequency on the
monitor?
Adjust the resolution and frequency of the video card.
(Refer to the Preset Timing Modes).
LED is blinking but
no images on the
screen.
Is the frequency
properly adjusted
when checking the
Display Timing on
the menu?
Adjust the frequency properly by
referring to the video card manual
and the Preset Timing Modes.
Have the Windows
colors been set
properly?
Windows XP :
Set the resolution at the Control Panel → Appearance
and Themes → Display → Settings.
There are only 16
colors shown on the
screen. The screen
colors have
changed after
changing the video
card.
(The maximum frequency per
resolution may differ from product
to product.)
Windows ME/2000 :
Set the resolution at the Control Panel → Display →
Settings.
Has the video card
been set properly?
Set the video card by referring to the video card
manual.
There is a message
that reads
"Unrecognized
monitor, Plug & Play
(VESA DDC)
monitor found".
Have you installed
the monitor driver?
Install the monitor driver according to the Driver
Installation Instructions.
See the video card
manual to see if the
Plug & Play (VESA
DDC) function can
be supported.
Install the monitor driver according to the Driver
Installation Instructions.
Check when
MagicTune™ does
not function
properly.
MagicTune™ feature
is found only on PC
(VGA) with Window
OS that supports
Plug and Play.
* To check whether your PC is available for
MagicTune™ feature, follow the steps below (When
Windows™ is XP);
Control Panel → Performance and Maintenance →
System → Hardware → Device Manager → Monitors
→ After deleting Plug and Play monitor, find 'Plug and
Play monitor' by searching new Hardware.
MagicTune™ is an additional software for the monitor.
Some graphic cards may not support your monitor.
When you have a problem with the graphic card, visit
our website to check the compatible graphic card list
provided.
http://www.samsung.com/monitor/magictune
MagicTune™
doesn't work
properly.
Have you changed
your PC or video
graphic card?
Download the latest program. The program can be
downloaded
http://www.samsung.com/monitor/magictune
Visit the MagicTune™ website and download the installation software for MagicTune™ MAC.
Check the following items if there is trouble with the monitor.
Check if the power cord and the video cables are properly connected to the computer.
Check if the computer beeps more than 3 times when booting.
(If it does, request an after-service for the main board of the computer.)
If you installed a new video card or if you assembled the PC, check if the installed the adaptor(video)
driver and the monitor driver.
Check if the scanning ratio of the video screen is set at 56 Hz ~ 75 Hz.
(Do not exceed 75 Hz when using the maximum resolution.)
If you have problems in installing the adaptor (video) driver, boot the computer in Safe Mode, remove
the Display adaptor at the "Control Panel → System → Device Administrator" and then reboot the
computer to reinstall the adaptor (video) driver.
If problems repeatedly occur, contact an authorized service center.
Q&A
Question
How can I change the frequency?
Answer
Frequency can be changed by reconfiguring the video card.
Note that video card support can vary, depending on the
version of the driver used.
(Refer to the computer or the video card manual for details.)
How can I adjust the resolution?
Windows XP :
Set the resolution at the Control Panel → Appearance and
Themes → Display → Settings.
Windows ME/2000 :
Set the resolution at the Control Panel → Display →
Settings.
Contact the video card manufacturer for details.
How can I set the Power Saving
function?
Windows XP :
Set the resolution at the Control Panel → Appearance and
Themes → Display → Screen Saver.
Set the function at BIOS-SETUP of the computer.
Windows ME/2000 :
Set the resolution at the Control Panel → Display → Screen
Saver.
Set the function at BIOS-SETUP of the computer.
Refer to Windows/Computer Manual
How can I clean the outer case/LCD
Panel?
Disconnect the power cord and then clean the monitor with
a soft cloth, using either a cleaning solution or plain water.
Do not leave any remains of the detergent nor scratch the
case. Do not allow any water to go inside the monitor.
Are the ultrasonic waves from the
electronic pen harmful to the human
body when used over a long time?
Although you may hear a subtle sound, ultrasonic waves
are harmless to the human body.
Why are there 2 buttons emitting
ultrasonic waves?
Ultra waves are emitted through the 2 buttons so as
to emit the waves in balance when drawing on the LCD
screen with the electronic pen.
Self-Test
Self-Test Feature Check | Warning Messages | Environment | Useful Tips
Your monitor provides a self test feature that allows you to check whether your monitor is functioning
properly.
Self-Test Feature Check
Turn off both your computer and the monitor.
Unplug the video cable from the back of the computer.
Turn on the monitor.
If the monitor is functioning properly, you will see a box in the illustration below.
This box appears during normal operation if the video cable becomes disconnected or damaged.
Turn off your monitor and reconnect the video cable; then turn on both your computer and the
monitor.
If your monitor screen remains blank after using the previous procedure, check your video controller
and computer system; your monitor is functioning properly.
Warning Messages
If there is something wrong with the input signal, a message appears on the screen or the screen
goes blank although the power indicator LED is still on. The message may indicate that the monitor is
out of scan range or that you need to check the signal cable.
Environment
The location and the position of the monitor may influence the quality and other features of the
monitor.
If there are any sub woofer speakers near the monitor, unplug and relocate the woofer to another
room.
Remove all electronic devices such as radios, fans, clocks and telephones that are within 3 feet
(one meter) of the monitor.
Useful Tips
A monitor recreates visual signals received from the computer. Therefore, if there is trouble with the
computer or the video card, this can cause the monitor to become blank, have poor coloring, noise,
Video mode not supported, etc. In this case, first check the source of the problem, and then contact
the Service Center or your dealer.
Judging the monitor's working condition
If there is no image on the screen or a "Not Optimum Mode", "Recommended Mode 1280 x 1024 60
Hz" message comes up, disconnect the cable from the computer while the monitor is still powered on.
If there is a message coming up on the screen or if the screen goes white, this means the monitor
is in working condition.
In this case, check the computer for trouble.
Specifications
General
Model Name
SyncMaster 720TD
LCD Panel
Size
17 " Diagonal (43 cm)
Display area
337.92 mm (H) x 270.336 mm (V)
Pixel Pitch
0.264 mm (H) x 0.264 mm (V)
Type
a-si TFT active matrix
Synchronization
Horizontal
30 ~ 81 kHz
Vertical
56 ~ 75 Hz
Display Color
16.2 M Colors
Resolution
Optimum resolution
1280 x 1024@60 Hz
Maximum resolution
1280 x 1024@75 Hz
Input Signal, Terminated
RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB,
0.7 Vp-p, Positive at 75 Ω,
Separate H/V sync, Composite sync, SOG, TTL level, positive or negative
Maximum Pixel Clock
135 MHz (Analog)
Power Consumption
AC 100 to 240 Vac(± 10 %), 60/50 Hz ± 3 Hz
Signal Cable
Tableau Signal Cable, Detachable, 1.8 m
15pin to 15pin D-sub cable, Detachable, 1.8 m (Option)
Signal Connectors
15pin 3-row D-Sub connector, USB+DVI connector
Power Consumption
Less than 34 W
Dimensions (W x D x H) / Weight
429.0 x 38.5 x 351.5 mm / 16.9 x 1.5 x 13.8 inch
429.0 x 225 x 424.5 mm / 16.9 x 8.9 x 16.7 inch (After installation of Stand)
429.0 x 160 x 423 mm / 16.9 x 6.3 x 16.7 inch (After folding the Stand) / 6.2 kg
VESA Mounting Interface
75 mm x 75 mm (for use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Operating
Temperature : 50 °F ~ 104 °F (10 °C ~ 40 °C)
Humidity : 10 % ~ 80 %, non-condensing
Storage
Temperature : -4 °F ~113 °F (-20 °C ~ 45 °C)
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and
computer systems will provide the best operating conditions and monitor settings. In most cases,
monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT LCD panel manufactured by using advanced semiconductor technology with precision of 1 ppm
(one millionth) above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color
seem to be bright sometimes or some of black pixels could be seen. This is not from bad quality and
you can use it without uneasiness.
For example, the number of TFT LCD sub pixels that is contained in this product are 3,932,160.
Design and specifications are subject to change without prior notice.
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy
by switching your monitor into a low-power mode when it has not been used for a certain amount of
time. The monitor automatically returns to normal operation when you press a key on the keyboard.
For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended
for long periods. The PowerSaver system operates with a VESA DPMS compliant video card installed
in your computer. Use a software utility installed on your computer to set up this feature.
State
Normal Operation
Power saving mode
Power off
EPA/ENERGY 2000
(Power button)
Power Indicator
Green
Green, Blinking
Black
Power Consumption
Less than 1 W
(Off-mode)
Less than 34 W
Less than 1 W
This monitor is EPA ENERGY STAR® compliant and ENERGY2000
compliant when used with a computer equipped with VESA DPMS
functionality.
As an ENERGY STAR® Partner, SAMSUNG has determined that this
product meets the ENERGY STAR® guidelines for energy efficiency.
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the
screen will be adjusted automatically. However, if the signal differs, the screen may go blank while
the power LED is on. Refer to the video card manual and adjust the screen as follows.
Preset Timing Modes
Display Mode
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
MAC, 640 x 480
35.000
66.667
30.240
-/-
MAC, 832 x 624
49.726
74.551
57.284
-/-
MAC, 1152 x 870
68.681
75.062
100.00
-/-
IBM, 640 x 350
31.469
70.086
25.175
+/-
IBM, 640 x 480
31.469
59.940
25.175
-/-
IBM, 720 x 400
31.469
70.087
28.322
-/+
VESA, 640 x 480
37.861
72.809
31.500
-/-
VESA, 640 x 480
37.500
75.000
31.500
-/-
VESA, 800 x 600
35.156
56.250
36.000
+,-/+,-
VESA, 800 x 600
37.879
60.317
40.000
+/+
VESA, 800 x 600
48.077
72.188
50.000
+/+
VESA, 800 x 600
46.875
75.000
49.500
+/+
VESA, 1024 x
768
48.363
60.004
65.000
-/-
VESA, 1024 x
768
56.476
70.069
75.000
-/-
VESA, 1024 x
768
60.023
75.029
78.750
+/+
VESA, 1152 x
864
67.500
75.000
108.00
+/+
VESA, 1280 x
60.000
60.000
108.00
+/+
960
VESA, 1280 x
1024
63.981
60.020
108.00
+/+
VESA, 1280 x
1024
79.976
75.025
135.00
+/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the
screen horizontally is called Horizontal Cycle and the inverse number of
the Horizontal Cycle is called Horizontal Frequency. Unit : kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many
times per second to display an image to the user. The frequency of this
repetition is called Vertical Frequency or Refresh Rate. Unit : Hz
Contact SAMSUNG WORLD-WIDE
If you have any questions or comments relating to Samsung products, please contact the
SAMSUNG customer care center.
North America
CANADA
1-800-SAMSUNG (7267864)
http://www.samsung.com/ca
MEXICO
01-800-SAMSUNG (7267864)
http://www.samsung.com/mx
U.S.A
1-800-SAMSUNG (7267864)
http://www.samsung.com
ARGENTINE
0800-333-3733
http://www.samsung.com/ar
BRAZIL
0800-124-421
http://www.samsung.com/br
CHILE
800-726-7864 (SAMSUNG)
http://www.samsung.com/cl
COSTA RICA
0-800-507-7267
http://www.samsung.com/latin
ECUADOR
1-800-10-7267
http://www.samsung.com/latin
EL SALVADOR
800-6225
http://www.samsung.com/latin
GUATEMALA
1-800-299-0013
http://www.samsung.com/latin
JAMAICA
1-800-234-7267
http://www.samsung.com/latin
PANAMA
800-7267
http://www.samsung.com/latin
PUERTO RICO
1-800-682-3180
http://www.samsung.com/latin
REP. DOMINICA
1-800-751-2676
http://www.samsung.com/latin
TRINIDAD &
TOBAGO
1-800-7267-864
http://www.samsung.com/latin
VENEZUELA
1-800-100-5303
http://www.samsung.com/latin
02 201 2418
http://www.samsung.com/be
Latin America
Europe
BELGIUM
CZECH REPUBLIC
844 000 844
http://www.samsung.com/cz
DENMARK
38 322 887
http://www.samsung.com/dk
FINLAND
09 693 79 554
http://www.samsung.com/fi
FRANCE
08 25 08 65 65 (€ 0,15/min)
http://www.samsung.com/fr
GERMANY
01805 - 121213 (€ 0,12/Min)
http://www.samsung.de
HUNGARY
06 40 985 985
http://www.samsung.com/hu
ITALIA
199 153 153
http://www.samsung.com/it
LUXEMBURG
02 261 03 710
http://www.samsung.lu
NETHERLANDS
0900 20 200 88 (€ 0.10/Min)
http://www.samsung.com/nl
NORWAY
231 627 22
http://www.samsung.com/no
POLAND
0 801 801 881
http://www.samsung.com/pl
PORTUGAL
80 8 200 128
http://www.samsung.com/pt
SLOVAKIA
0850 123 989
http://www.samsung.com/sk
SPAIN
902 10 11 30
http://www.samsung.com/es
SWEDEN
08 585 367 87
http://www.samsung.com/se
U.K
0870 242 0303
http://www.samsung.com/uk
RUSSIA
8-800-200-0400
http://www.samsung.ru
UKRAINE
8-800-502-0000
http://www.samsung.com/ur
AUSTRALIA
1300 362 603
http://www.samsung.com/au
CHINA
800-810-5858, 010- 6475 1880
http://www.samsung.com.cn
HONG KONG
2862 6001
http://www.samsung.com/hk
INDIA
3030 8282, 1600 1100 11
http://www.samsung.com/in
INDONESIA
0800-112-8888
http://www.samsung.com/id
JAPAN
0120-327-527
http://www.samsung.com/jp
MALAYSIA
1800-88-9999
http://www.samsung.com/my
PHILIPPINES
1800-10-SAMSUNG (7267864)
http://www.samsung.com/ph
SINGAPORE
1800-SAMSUNG (7267864)
http://www.samsung.com/sg
THAILAND
1800-29-3232, 02-689-3232
http://www.samsung.com/th
TAIWAN
0800-329-999
http://www.samsung.com/tw
VIETNAM
1 800 588 889
http://www.samsung.com/vn
CIS
Asia Pacific
Middle East & Africa
SOUTH AFRICA
0860 7267864 (SAMSUNG)
http://www.samsung.com/za
U.A.E
800SAMSUNG (7267864)
http://www.samsung.com/mea
Terms
Dot Pitch
The image on a monitor is composed of red, green and blue dots. The closer the dots, the higher the
resolution. The distance between two dots of the same color is called the 'Dot Pitch'. Unit : mm
Vertical Frequency
The screen must be redrawn several times per second in order to create and display an image for the
user. The frequency of this repetition per second is called Vertical Frequency or Refresh Rate. Unit :
Hz
Example : If the same light repeats itself 60 times per second, this is regarded as 60 Hz.
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the screen horizontally is called
Horizontal Cycle. The inverse number of the Horizontal Cycle is called Horizontal Frequency. Unit :
kHz
Interlace and Non-Interlace Methods
Showing the horizontal lines of the screen from the top to the bottom in order is called the NonInterlace method while showing odd lines and then even lines in turn is called the Interlace method.
The Non-Interlace method is used for the majority of monitors to ensure a clear image. The Interlace
method is the same as that used in TVs.
Plug & Play
This is a function that provides the best quality screen for the user by allowing the computer and the
monitor to exchange information automatically. This monitor follows the international standard VESA
DDC for the Plug & Play function.
Resolution
The number of horizontal and vertical dots used to compose the screen image is called 'resolution'.
This number shows the accuracy of the display. High resolution is good for performing multiple tasks
as more image information can be shown on the screen.
Example :If the resolution is 1280 x 1024 , this means the screen is composed of 1280
horizontal dots (horizontal resolution) and 1024 vertical lines (vertical resolution).
For Better Display
Adjust computer resolution and screen injection rate (refresh rate) oncomputer as described below to
enjoy the best quality of picture. You can have an uneven quality of picture in the screen if the best
quality of picture is not provided in TFT-LCD.
Resolution : 1280 x 1024
Vertical frequency (refresh rate) : 60 Hz
TFT LCD panel manufactured by using advanced semiconductor technology with precision of 1ppm
(one millionth) above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color
seem to be bright sometimes or some of black pixels could be seen.
This is not from bad quality and you can use it without uneasiness.
For example, the number of TFT LCD sub pixels that is contained in this product are 3,932,160.
When you clean the monitor and the panel outside, please apply the recommended small amount of
cleaner by using soft and dry cloth and polish it. Let LCD area not to be forced but to be scrubbed out
softly.
If excessive force is applied, you can have a stain on it.
If you are not satisfied with the quality of picture, you can get better quality of picture by executing
"auto adjustment function" in display screen that is appeared as window termination button is
pressed.
If there's still noise after automatic adjustment, use FINE/COARSE adjustment function.
If you view a fixed screen for an extended period of time, residual image or blurriness may appear.
Change the mode to energy save or set a screensaver to moving picture when you need to be away
from the monitor for an extended period of time.
Authority
Information in this document is subject to change without notice.
© 2006 Samsung Electronics Co., Ltd. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co.,
Ltd. is strictly forbidden.
Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or
consequential damages in connection with the furnishing, performance, or use of this material.
Samsung is the registered trademark of Samsung Electronics Co., Ltd.; Microsoft, Windows and
Windows NT are registered trademarks of Microsoft Corporation; VESA, DPMS and DDC are
registered trademarks of Video Electronics Standard Association; the ENERGY STAR® name and
logo are registered trademarks of the U.S. Environmental Protection Agency (EPA). As an ENERGY
STAR® Partner, Samsung Electronics Co., Ltd. has determined that this product meets the ENERGY
STAR® guidelines for energy efficiency. All other product names mentioned herein may be the
trademarks or registered trademarks of their respective owners.
Class B
This device is a Class B digital apparatus. For Safety and EMC compliance guide, you may refer to
"Regulatory" Guide.
MÉXICO
IMPORTADO POR:
SAMSUNG ELECTRONICS MÉXICO. S.A. de C.V.
Vía Lopez Portillo No. 6, Col. San Fco. Chilpan
Tultitlán, Estado de México, C.P. 54940
Tel: 01-55-5747-5100 / 01-800-726-7864
EXPORTADO POR:
Samsung Electronics CO.,LTD.
416, Mae tan-3dong, Yeongtong - gu,
Suwon City, Gyeonggi-do Korea
Download PDF

advertising