Samsung | SR-608EV | Samsung SR-608EV User Manual

SR-608, 606/ENG 11/15/59 4:19 PM Page 1
SR-608EV/648EV/688EV (Dispensor Applied)
606EV-646EV/686EV
REFRIGERATOR
Before operating the unit, please read this manual throughly,
and retain for future reference.
If you took out of the power
supply outlet, you should plug
in again after five minutes.
DA68-60306A
ENGLISH
ELECTRO
OWNER’S
INSTRUCTIONS
SR-608, 606/ENG 11/15/59 4:19 PM Page 2
FEATURE
What is H.M.CYCLE(High-efficiency Multievaporator CYCLE)?
• A high efficiency cooling method adopting an
independent cooler and an independent cooling fan in freezing room and refrigerating room,
respectively.
• A new cooling method providing an economic
energy, power cooling function and supply of
high humidity cool air by independent cooler
and cooling fan.
What is sensitivity technology?
• A theory for meeting the sensuous demands
from consumers by supplying the cool air that
suits their tastes for preserving foods. Neurofuzzy genic algorithm theory was applied so
that the optimum uniform refrigeration can be
maintained by automatically activating the
rotating fan for distribution of cool air at the
locations where foods are stored and supplying the cool air quickly to places where it is
mostly needed.
What is genic algorithm
(GA-FUZZY)
• A theory that senses the inside temperature of
refrigerator with temperature sensor and
controls it to be in an optimum state of uniform
refrigeration by applying the genetic principle
of natural ecosystem, i.e the law of the fittest
Øs survival and training to Micom.
CONTENTS
Ready to use
Contents ...............................................................................1
Warnings for safety ..............................................................2
Cautions for safety ...............................................................4
Features ...............................................................................6
Ready to use ........................................................................8
Front operating panel.........................................................10
How to use
How to use freezing room..................................................12
How to use refrigerating room ...........................................14
How to preserve the refrigerated foods.............................17
Functions of water dispenser.............................................19
Installation and cares
How to clean ......................................................................21
How to disassemble and assemble the
water supply device......................................................23
How to disassemble the accessories................................26
How to install......................................................................27
Before asking for service
Before asking for service ...................................................31
Questions...........................................................................33
1
SR-608, 606/ENG 11/15/59 4:19 PM Page 3
WARNING FOR SAFETY
This is to prevent users or other persons from being wounded or injured, by using the present product
properly. Be sure to observe these contents for safety. (After reading these contents, please keep in such
a safe place as to look up)
Contents of Caution/Warning
Contents of indication
Represents the contents of prohibition.
Warning
Represents the contents that
death or heavy injury of a person
is foreseen.
Represents the prohibition of disassembly.
Represents the prohibition of contact.
Represents what has to be observed.
Caution
Represents that a power plug has to be
separated from the plug socket.
Represents the contents that
injury of a person or damage of
material is foreseen.
Represents earth for prevention of electric
shock.
WARNING
Do not insert the power
plugs for many products
at the same time.
• May cause abnormal generation
of heat or fire.
Set the power plug free from the
back side of the refrigerator.
• Damaged power plug may cause
fire due to overheating.
• If the power cord is damaged,
avoid a hazard by
replacing it through the
manufacturer or its
service agent or a
similarly qualified
person.
Do not directly spray water
inside or outside of the
refrigerator
• May cause fire or electric shock.
Do not spray inflammable gas
near the refrigerator.
• May cause explosion or fire.
Do not bend the power cord
with excessive force or do not
have the power cord pressed by
heavy article.
• May cause fire or electric shock.
Do not store a volatile and inflammable substance in the
refrigerator.
• Storage of benzene, thinner,
alcohol, ether, LP gas, etc., may
cause explosion.
BEN
ETHER
ZENE
GASOLINE
SIVE
ADHE
2
SR-608, 606/ENG 11/15/59 4:19 PM Page 4
WARNING
Do not put a tank filled with water
on the product.
• If water poured, it cause bad insulation of the electric parts which
may lead to fire or electric shock.
Do not install the refrigera-tor in
the wet place or the place which
water splashes.
• Deterioration of insulation of electric parts may cause electric shock
or fire.
Do not insert the power plug with
the wet hand.
• May cause electric shock.
Do not disassemble, repair or
alter.
• It may cause fire or abnormal
operation which leads to injury.
Pull the power plug out for
exchanging the interior lamp of
the refrigerator.
• It may cause electric shock.
Be sure to earth.
• If earthing is not done, it will cause
breakdown and electric shock.
(Please refer to page 29.)
If and when gas leaks, immediately ventilate
without touching the refrigerator and the plug.
• Explosion of gas may cause fire and a burn.
3
Dispose refrigerator after door or door’s packing
is removed, if disposition is required.
• It is dangerous for child to enter the refrigerator for
play-in with door closed.
SR-608, 606/ENG 11/15/59 4:19 PM Page 5
CAUTIONS FOR SAFETY
CAUTION
Do not store too much foodstuffs therein.
• Opening of the door may cause pouring over which
may inflict a wound.
Do not store narrow and lengthy bottles or foods
in a small multi-purpose room.
• It may hurt you when refrigerator door is opened and
closed resulting in falling stuff down.
If the hole of the power plug socket is loose,
don’t insert the power plug.
• It may cause electric shock and fire.
Do not put bottles or kinds of glass in the freezing
room.
• Freezing of the contents may inflict a wound.
Do not store articles on the product.
• Opening or closing of the door may cause throwing
down which may inflict a wound.
Do not plunk out the power cord by pulling the
portion of it.
• It may inflict a wound.
Do not let a child be hung down from the door.
• Injury may occurs, when the product falls down or a
finger is jammed in the door.
Do not store pharmaceutical products, scientific
materials, etc., in the refrigerator.
• The products which temperature control shall be
strict shall not be stored in the refrigerator.
4
SR-608, 606/ENG 11/15/59 4:19 PM Page 6
CAUTION
Do not touch the tank and the food stuffs of the
frezzing room with the wet hand.
• It may cause frostbite.
Do not enter the hand into the bottom surface of
the product.
• Sharp edge may inflict a wound.
Please wipe out foreign materials of the metal
option of the power plug cleanly.
• Use of it as it is may cause fire.
If you want to insert the power plug again, please
insert it five minutes after pulling out of the plug
socket.
• Abnormal operation of freezing device may cause
breakdown of it.
Afterfive
minutes
5
Move it by catching the upper handle of rear side
and the lower handle of front side.
• Slippery is caused to hurt, when other part is
grasped.
Use handle when opening and closing the
refrigerator door.
• In case of using other parts than handle, it may hurt
you with your finger jammed.
If the refrigerator is not to be used for a long time,
pull out the power play.
• Due to deterioration of insulation, mau cause fire.
When abnormal sound, small or smoke is noticed,
pull a power plug off immediately, then call service
center.
SR-608, 606/ENG 11/15/59 4:19 PM Page 7
FEATURES
X-FLOW COOLING SYSTEM FOR REDUCING THE LOSS OF COOL AIR!
Rotation cooling method
• The current cooling method has been a fixed one where the cool air comes directly out of one or 2~3 walls of
refrigerator.
X-FLOW cooling refrigerator has adopted the rotating fans in all 3 rooms that make use of the sensitivity
technology that rotate vigorously, allowing the cool air to be spurted out and the whole area including every corner
in refrigerator to be cool instantly.
A keen watch for cool air
• When the door is open, you don’t have to worry about any change of food tastes since the rotating cool air that
adopts the sensitivity technology is turning around foods without any gaps and does not allow any contact of the
foods with warm air.
• You don’t have to worry about any leakage of cool air since the cool air moves around foods in center even in the
case of frequent door opening.
Water dispenser for reducing the frequency of opening the door (Models applied :
608EV/648EV/688EV)
• It adopts the water dispenser that allows water supply without opening the door and therefore the frequency of
opening door drops to over 30%, resulting in about 10% of power savings.(Refer to page 20)
Power saving automatic door close and warning device for door opening.
• In case the door is slightly open(within 15°) by mischiefs of children or mistakes of housewives, the door is
automatically closed and prevents any loss of cool air. Also, in case of opening of over 15°, a melody for warning
housewives sounds, making it a complete way for saving power(Refer to page 11).
Rail design for quick opening and closing
• It adopts a rail design in super-high humidity vegetables room and high humidity special fresh room that allows a
smooth movement when lightly pulling and pushing the handle without any force and so you can quickly pull out
the vegetables and fruits. Loss of cool air is prevented by the quick door opening and closing.(Refer to page
17~18)
6
SR-608, 606/ENG 11/15/59 4:19 PM Page 8
SEPARATE AND INDEPENDENT COOLING OF REFRIGERATING
AND FREEZING ROOMS!
Refrigerator of energy-saving type
• It adopts the high-efficiency Multi-evaporator CYCLE that makes it possible to cool the refrigerating room and
freezing room separately and to reduce the power consumption and energy.
Super-power cooling technique for quick refrigeration.
• Selection of power freezing and power refrigerating by independent cooler and cooling fan allows the quick
cooling and preserving the freshness of foods.(pages 13, 15)
Natural humidity vegetable room lasting 3 times longer even without vinyl wraps.
• The independent cooling method is supplying the cool air with 4°~5 times of more humidity than conventional
refrigerator through the indirect cooling technique by which the cool air can not touch the vegetables and fruits
directly and therefore the freshness with the same natural humidity as that of producing areas can be
maintained for a long time
NATURALISM FOR REFRIGERATORS, TOO!
Refrigerator that does not destroy the ozone layer!
• It uses the new insulating materials, the new refrigerant (R-134A) whose ODP(Azone Depletion Potential) is zero
7
SR-608, 606/ENG 11/15/59 4:19 PM Page 9
READY TO USE
This mark indicates the page to be referred to.
Please install the refrigerator with
sufficient space apart at the place
with a flat bottom surface. 27
• An incorrect leveling may cause noises and
impossible cooling.
1
2
Please wipe and clean the
refrigerator.
• Please wipe and clean the inside and outside of
refrigerator.
over 5cm
3
ov
er
5c
m
over 30cm
Please insert the plug in an
outlet. 29
• The refrigerator should be grounded.
• It is desirable to connect the power 1 hour after
its installation.
• When plugging in for the first time or plugging in
again after pulling it out, the cooler starts operating after about 5 minutes to prevent excessive
load to cooler.
4
Please put foods in the
refrigerator.
• It is recommended that foods are put in the
refrigerator that was cooled for 2~3 hours after
plugging in.
❊ Please refer to page 1 for operation in 110V area.
8
SR-608, 606/ENG 11/15/59 4:19 PM Page 10
THE CORRECT WAY OF PRESERVING FOODS.
9
Please keep them after washing.
Please store foods after dividing into small
pieces.
Please do not store foods which are apt to go bad
in low temperature.
(Examples : Bananas, Pineapples, Tomatoes etc.)
Please place watery foods(particularly bean
curds) on the front area of shelf in refrigerating
room.
• It may be possible that foods placed on areas where
cool air is coming out are frozen.
Please arrange foods with proper distance each
other.
• If the exit of cool air is blocked, the storing efficiency
gets low due to the bad cool air circulation.
Please cool off the hot foods before putting them
in the refrigerator.
• It reduces power consumption and also makes a
better cooling.
SR-608, 606/ENG 11/15/59 4:19 PM Page 11
FRONT OPERATING PANEL
This mark indicates the page to be referred to.
Power freezing 13
Power refrigeration 15
It freezes the foods in the freezing room
at a high speed.
It cools foods in refrigerating room at a high
speed down to a fixed temperature.
QUICK FRE.
LO
LO
HI
HI
QUICK REF.
FRE. CONTROL
REF. CONTROL
DOOR ODOR QUICK
ALARM FREE FRE.
FRE.
CONTROL
REF.
CONTROL
QUICK
REF.
HI-MOISTURE
Temperature control button of freezing room
It is able to adjust the temperature in freezing room. Whenever the button is pressed, the
sequence of Low → Low Mid → Mid → Mid High → High is selected.
Temperature control button of refrigerating room
It is able to adjust the temperature in the refrigerating room
Whenever the button is pressed, the sequence of
Low → Low Mid → Mid → Mid High → High is selected.
10
SR-608, 606/ENG 11/15/59 4:19 PM Page 12
DISPLAY PANEL
1
High moisture refrigerating
function
A high moisture refrigerating display lamp is
always on when the refrigerator is in operation.
• The refrigerator adopted separate coolers in
freezing and refrigerating rooms, respectively,
that can supply a high moist cool air and therefore it can preserve the foods in fresh state.
2
A warning sound(Dingdong-Dingdong) indicates that door is open.
• In case the door is open wider than 15°, after 2
minutes the warning sounds for about 10
seconds with about 1 minute interval.
DOOR
ALARM
HI-MOISTURE
3
Deodorizing display lamp
This lamp is always on when the refrig-erator
is in operation.
Without any specific operation, the refrigerator remains in deodorizing mode while air is
circulating.
ODOR
FREE
Power savings of indoor lamp
• When the door is open for over 10 minutes,
the indoor lamps automatically go off.
11
Door-alarm function
(Door opening)
4
Display of super X-flow function
If temperature in refrigerating room is getting
high with a lot of foods in it or the door is
open, the half-circle red lamps in the center
turn on in automatic sequence.
• You do not have to worry about any leakage of
cool air even though the door is open because
the rotating cool air is moving around foods in
center.
• The display lamp is on when the temperature in
refrigerating room gets uniform since the cooling
is made quickly by the rotation cooling technique.
SR-608, 606/ENG 11/15/59 4:19 PM Page 13
HOW TO USE FREEZING ROOM
Drying room
ICE TRAY
Indoor lamp in freezing
JH
ICE
ce storage tank
Air-shower
What is the technique of air-shower?
It is a technique that allows spraying the cool air evenly in freezing
room, thus foods can be frozen more uniformly.
HOW TO MAKE ICE
1
Please pour water of appropriate amount
on the ice tray.
2
Please insert ice tray into the shelf.
12
SR-608, 606/ENG 11/15/59 4:19 PM Page 14
POWER FREEZING/TEMPERATURE CONTROL OF FREEZING ROOM
The artificial intelligent function keeps the adjusted temperature of freezing room in the optimum state conforming
with conditions of use.
Power freezing(Quick freezing)
When you want to freeze foods at a fast speed or to get ice quickly,
●
●
The red lamp is on when selecting Power freezing by pressing “QUICK FRE” Button
Please press the button one more time if you want to cancel “QUICK FRE”
LOW
When the amount of foods to be stored is small,
●
●
Please select “LOW” by pressing FRE. control button.
Whenever pressing the button at “LOW”, temperature is set in sequence of
“LOW MID → MID”.
MID
When using it normally,
Please select an appropriate position between “LOW” and “MID” or “MID” and “HIGH”, depending on the amount
of foods to be stored and frequency of use.
● ”MID” is the normal position.
● The temperature is changed in sequence of “MID HIGH → HIGH” whenever pressing the button at “MID”.
●
HIGH
When making ice or there are a lot of foods to be stored.
●
●
Please select “HIGH” by pressing the temperature control button.
When pressing one more time at “HIGH”, “LOW” is selected.
Whenever pressing the temperature control, the temperature setting is changed in sequence of
“LOW” → MID LOW → MID → MID HIGH → HIGH” and it goes to “LOW” when pressing the button one
more time at “HIGH”.
● Since power freezing function is automatically completed, it is automatically transferred, after power
freezing, to the previous temperature setting before the power freezing function is operated.
(Example : If it had been used in “LOW” mode, it automatically goes back to “LOW” after completing
“POWER FREEZING”.
● “MID” of freezing room is automatically set after initial power supply or power failure.
●
13
SR-608, 606/ENG 11/15/59 4:19 PM Page 15
HOW TO USE REFRIGERATING ROOM
Models applied :
SR-608EV/648EV/688EV(Dispenser Model)
Water tank
High humidity special
fresh room (Chilled room)
Egg tray
Guard variety
Jumbo
guard bottle
High humidity
Vegetable room
Transparent safe shelf
Space for drinks
14
SR-608, 606/ENG 11/15/59 4:19 PM Page 16
POWER REFRIGERATION/TEMPERATURE CONTROL OF REFRIGERATING ROOM
The artificial intelligent function keeps the adjusted temperature of refrigerating room in an optimum state conforming with conditions of use.
Power refrigeration
When you want to cool the foods quickly.
●
●
The red lamp is on when selecting POWER REFRIGERATING by pressing “QUICK ref” button
Please press the button one more time for cancelling power refrigeration.
LOW
When foods are frozen or the quantity of foods is small,
●
●
Please select “LOW” by pressing the temperature control button
Whenever pressing the button at “LOW”, the temperature setting is changed in sequence of
“LOW MID → MID”.
MID
When in normal use or storing Kimchi,
Please select an appropriate position between “LOW” and “MID” or “MID” and “HIGH”, depending on the quantity
of foods to be stored and frequency of use.
● “MID” is the normal position.
● Whenever pressing the button from “MID”, the temperature setting is changed in sequence of
“MID HIGH → HIGH”.
●
HIGH
When refrigeration is bad or there are a lot of foods to be stored,
●
●
Please select “HIGH” by pressing the temperature control button.
When pressing one more time from “HIGH”, the temperature is set to “LOW”.
15
SR-608, 606/ENG 11/15/59 4:19 PM Page 17
Whenever pressing the temperature control, the temperature setting is changed in sequence of
“LOW → LOW MID→ MID → MID HIGH → HIGH” and it goes to “LOW” when pressing the button one
more time at “HIGH”.
● Since power refrigerating function is automatically completed, it is automatically transferred, after
power refrigeration, to the previous temperature setting before the power refrigerating function is
operated.
(Example : If it had been used in “LOW” mode, it automatically goes back to “LOW” after
completing “POWER REFRIGERATING” (“QUICK REF”).
● ”MID” of refrigerating room is automatically set after initial power supply or power failure.
● Under the environment of below 5°, foods may be frozen.
(The normal temperature in refrigerating room is between 0°~10°, However, foods can be frozen by
the influence of external temperature when the environmental temperature is low and it causes the
temperature to be out of control ranges.)
● The refrigerator door may not be open smoothly due to internal pressure difference generated when
trying to open it again within 5°~10 seconds after closing.
●
16
SR-608, 606/ENG 11/15/59 4:19 PM Page 18
HOW TO PRESERVE THE REFRIGERATED FOODS
1
High humidity special fresh room
(chilled Room )
• Please use this room for foods to be stored in
colder environments than refrigerating room.
❊ Please keep meat or fish in freezing room for its
long storage.
3
Eggs carrier
• Please keep eggs in the eggs carrier.
❊ The products with water dispensers (Models
applied: SR-608EV/648EV/668EV) contains two
eggs carriers.(Refer to figure of page 14)
2
Re-enforced glass shelf
• Please keep the side dish foods in storage bowl
or other refrigerated foods with a proper distance
apart.
❊ The shelf in refrigerating room is a re-enforced
glass one unliable to destruction even when
falling down, making sure of its safe use.
4
Space for multi-use
• Please use this space for storing butter, milk ,
yogurt in small package or drinks.
Milk
Butter
17
Milk
Butter
SR-608, 606/ENG 11/15/59 4:19 PM Page 19
5
Space for drinks
6
• Lower space for beer, 1000ml milk, juice and
upper space for 1.5 l tank or water jar.
Lower space
● The
Upper space
Super high humidity vegetable room
• The rail-type super high humidity vegetable room
is an indirect cooling method with a closed loop
that prevents the cool air from touching foods
directly so it is possible for foods with moisture
and humidity of producing areas to be maintained
for a very long time.
• Due to the inside partitions, vegetables and fruits
can be stored separately.
frequent opening of refrigerator door may cause dews on the inside of it.
18
SR-608, 606/ENG 11/15/59 4:19 PM Page 20
FUCTIONS OF WATER DISPENSER
Models applied : SR-608EV/648EV/688EV
What is the water dispenser? If a water tank full of water and equipped with water supply device is inserted into the
location where the water supply lever in the refrigerating room is connected to, the cold water can be available at the
outside of door even without opening the door by pressing the water supply lever.
Water tank
Milk
Milk
Milk
When in no use of water
dispenser function,
After removing water tank,
tightly insert the cap for
sealing into the
connector of
water dispenser
so that no cool
air is leaked.
• Please drain the water completely from water tank by pressing the water supply lever after emptying it
when in no frequent use of water dispenser.
• Please do not use juice or soda drinks because water tank or water supply system can be polluted by
their sugar contents. When it was used with those drinks, please make sure to wash it with clean water.
• A cold water will be available right after the cold water stored in refrigerating room in advance is put into
water tank.
• Please clean the water tank frequently after it was filled with tea etc. for a long time since the water tank
is subject to change of color or smell and also the residues of tea may cause an abnormal operation of
water dispenser.
• Please adjust it to “OPEN” when pulling out water.
• Please adjust it to “CLOSE” when in no use or any worry for children mischiefs.
19
SR-608, 606/ENG 11/15/59 4:19 PM Page 21
HOW TO USE WATER DISPENSER (MODELS APPLIED : SR-608EV/648EV/688EV)
Groove for hand-grip
1
Please lift up and pull out the water tank.
• Please hold the groove of both hand grips and
pull out the water tank while lifting it up.
• Please clean the inside of water tank when using
it for the first time.(Refer to page 21)
2
Please fill the water tank with water after placing it up on flat surface except for water supply device.
• Please supply the water up to 2.5l of water level window since water may overflow when closing the round lid if water is too full.
• It is possible to fill the water with water tank inserted in the refrigerator.
Water level window Hand-grip
Round lid
2.5
Water tank
Water supply device
Method 1.: Please fill the water after lift up the round lid
to the arrow direction to open it.
3
Please close the refrigerator door
after inserting the water tank.
• Please confirm whether the water
exit of water supply device is outside
after closing the door.
Method 2.: Please fill the water after holding and lifting
both hand-grips of large lid to open it.
4
Please press down the water supply lever with hands after placing
cup on platform for cup.
• Please lay the cup deep inside to the extent the
cup can reach the inner wall slightly.
• If hands were removed from cup, there is no
water supplied.
• Please desert 2~3 cups of water when using the
water dispenser for the
Water supply lever
first time after
installation.
• In case of continuous
water drinking, about
10~15 cups of water
are availble.
20
SR-608, 606/ENG 11/15/59 4:19 PM Page 22
HOW TO CLEAN
HOW TO CLEAN WATER DISPENSER (MODELS APPLIED : SR-608EV/648EV/688EV)
1
Please separate the large lid from water tank after Hand-grip
pulling it out.
• It can be separated from water tank when pulling up
both hand-grips of large lid.
Large lid
Water tank
2
Please separate the water tank from water supply
device.
Residue screen
• Please hold the upper part of water supply device and turn it to arrow
direction.
• If the water tank is removed from water supply device, the residue
screen fitted in inside can be separated.
❊ When assembling the residue screeen, please assemble it so that the
dead-end side face upward (to the inside of water tank)
Water supply device
3
After washing water tank and large
lid with neutral detergents, please
rinse them with water.
5
How to use water-spout
• Please frequently throw away water collected on the
water-spout and wipe it out with dry cloth after separating it from cup platform by slightly pressing “PUSH”.
Caution
21
Dead-end
side
Please clean the water supply
device and residues screen with a
soft brush.
• Please disassemble and clean once in a while.
4
cup platform
Water-spout
• Please do not boil the water supply device in hot water of over 60°
• Please be careful not to damage or lose the water supply device.
• Please do not let children mishandle the water supply lever. It may cause the water overflow or any
trouble.
SR-608, 606/ENG 11/15/59 4:19 PM Page 23
OTHER WAYS OF CLEANING
1
High humidity special fresh room
(Chilled room)
Please wipe and clean the high humidity special
fresh room with water and neutral detergent
after pulling it out.
3
Rubber packing
• Clean the rubber packing with neutral detergent as the door can not be easily closed if it
is polluted.
• Wipe the gaps between grooves along the
groove with cloths that were cut into small
parts and wound around a woodstick.
• Be careful not to damage it while cleaning.
Caution
• Dry the refrigerator with the door open
and the plug out when cleaning or not in
use for a long time.
• Do not clean the refrigerator by sprinkling water on it or by using benzene or
thinner.
2
Freezing room shelf/refrigerating
room (Re-enforced glass shelf)
When soaked with foods or stucked with
residues, please pull out the freezing
room/refrigerating room shelf and wipe it with
clean cloths, while spraying the ethanol for
sterilization all over its surface.
4
Low temperature catalyzing
deodorizer
• In case of heavy smells in the freezing and
refrigerating rooms. Use the low temperature
catalyzing deodorizer after disassembling ,
dipping into clean water and drying it
completely in the sunshine.
Catalyzer
• This refrigerator adopted the mobile
wheel at its rear that freely rotate up to
360° so that it can easily move whenever necessary and also it is convenient
for adjusting its position as well as for
cleaning.
22
SR-608, 606/ENG 11/15/59 4:19 PM Page 24
HOW TO DISASSEMBLE AND ASSEMBLE THE WATER SUPPLY DEVICE
When you want to further clean every corners of the water supply device, disassemble and assemble it after cleaning as follows.
HOW TO DISASSEMBLE (MODELS APPLIED : SR-608EV/648EV/688EV)
① Part (small rubber packing)
➁ Part
(2-1) Part (Medium rubber packing)
➂ Part (Large rubber packing)
➃ Part
➄ Part (Spring)
⑥ Part
23
SR-608, 606/ENG 11/15/59 4:19 PM Page 25
1
Pull out ① part while pressing the
lower end of ⑥ part with the thumb.
2
Pull out ⑥ part.
• At this time, pull it out lightly so as not to damage the ① part
(small rubber packing)
⑥ part
⑥ part.
① part
3
Separate ➁ part with the thumb by
pressing its locking part on one
side.
• At this time, be careful not to damage 2-1
part.(medium rubber packing)
Pull out ➄ part.
4
➄ part.
➁ part
5
Locking
part
2-1 part
Pull out ➂ part by tapping the ➃
part on the floor.
➃ part
➂ part
24
SR-608, 606/ENG 11/15/59 4:19 PM Page 26
HOW TO ASSEMBLE
1
Fit the ➂part, while pressing it,
into ➃part.
2
Fit the locking part of ➁part into
the hole of ➃part.
➁part
➂part
➃part
➃part
3
Insert ➄part and ⑥part into
➃part.
4
Insert the long portion of ⑥part into
the hole of ➁part.
• At this time, the popping portion of ⑥part has to
be fitted into the grooves of ➁part.
Hole
➁part
⑥part
➄part
➃part
Popping porting
⑥part
5
25
Insert ®Á part while pressing the
lower end of ® A part.
Caution
• Be careful not to recklessly pull out spring
or not to make the spring stretched.
• Water leakage may be caused by filling
water tank with water or by pressing water
supply lever if rubber packing or rubber
ring were missing while assembling.
Assemble all parts in steps without missing
any one of them.
SR-608, 606/ENG 11/15/59 4:19 PM Page 27
HOW TO DISASSEMBLE THE ACCESSORIES
Freezing room shelf
• Pull out the ice tray first and then lift up the front
part of freezing room shelf and pull it out forward.
Re-enforced glass shelf
• Hold the re-enforced glass shelf with both hands
as shown on the figure and pull it out forward.
• Depending on the size of tanks for storing foods,
the re-enforced glass shelf may be removed or
used with its height properly adjusted.
High humidity special fresh shelf
• Lift up and pull out the high humidity special fresh
shelf at the blocking point while pulling it out to the
arrow direction.
Low temperature catalyzing deodorizer
• After pulling out the high humidity special freshing
room forward, pull it out while pressing the ending
part of sill on the low temperature catalyzing
deodorizer.
Water tank
• Lift up and pull out the water tank as shown on the
figure.(Model applied :
SR-608EV/648EV/688EV)
Low temperature
catalyzing deodorizer
Vegetable room lid and box
• Lift up the vegetable room lid and pull it out
forward.
• Pull out vegetable box while lifting it up after pulling
forward to the middle point.
Space for drinks
• Lift up and pull out the space for drinks.
Vegetable room
26
SR-608, 606/ENG 11/15/59 4:19 PM Page 28
HOW TO INSTALL
HOW TO ADJUST LEVELING
Adjust the leveling of refrigerator.
• If the refrigerator is so installed to make its front a little high, the door can be easily opened and closed.
1
27
Refrigerator leaning to the left.
Make leveling by filling – driver into
the groove of adjustible leg on the
left side and turning it to arrow
direction.
2
Refrigerator leaning to the right
Make leveling by fitting – driver into
the groove of adjustible leg on the
right side and turning it to arrow direction.
SR-608, 606/ENG 11/15/59 4:19 PM Page 29
PRECAUTIONS FOR INSTALLATION
Aviod any flammable materials.
• Spraying of flammable materials
may cause a fire.
• It is dangerous to unplug when gas
is leaking.
1
ER
ETH
3
2
Do not keep other stuffs in rear and
top of refrigerator.
• Cooling efficiency gets low due to
bad ventilation that causes no
heat-sink.
• Do not place stuffs on top of refrigerator as they are apt to fall down.
4
Install the refrigerator at the place
where its environ-mental temperature is low.
• It provides a better cooling
efficiency.
• Avoid any direct sunshine.
E
ZEN
BEN
GAS
Avoid heat and water
• They may cause rust or color deterioration on exterior of refrigerator.
28
SR-608, 606/ENG 11/15/59 4:19 PM Page 30
HOW TO GROUND
The refrigerator should be grounded.
The purpose of grounding is to prevent any power leakage or electric shock caused by the current leakage from the
refrigerator.
❊ Never ground to gas pipes, telephone line and lightning rod as it is very dangerous at the time of lightning strikes.
In case of outlets without ground terminals.
• Bury the ground cable connected to a copper plate into
the ground with plenty of moistures at the depth of over
25CM, or use a power source which is equipped with
circuit breakers.
Ground
cable
25cm
Ground screw
29
SR-608, 606/ENG 11/15/59 4:19 PM Page 31
HOW TO EXCHANGE INDOOR LAMPS
First plug out from the outlet.
Freezing room indoor lamp
• Remove the indoor lamp cover by using – driver
and pull out the lamp and fit the front part of
indoor lamp cover into the groove and then fit the
rear part.
Refrigerating room indoor lamp
1. Unscrew the fixed bolt and separate the lamp by fitting the
– driver into two rear holes of indoor lamp cober and
pressing it.
2. Turn the indoor lamp to pull it out and replace it with a new
one.
hole
side feature
3. After fitting the front part of indoor lamp cover, fit the rear sill
area and then fix it with screw.
❊ In case of having difficulties in replacing and purchasing
parts, contact the nearest Samsung Electronic service
center.
30
SR-608, 606/ENG 11/15/59 4:19 PM Page 32
BEFORE ASKING FOR SERVICE
SYMPTIOMS
CHECK
Non-operation or bad refrigeration
• Check the connection of power plug.
• Isn’t the temperature control lamp of front operating
panel in “LOW” mode?
• Isn’t there sunshine or heat directly applied to
refrigerator.
• Isn’t the rear plate of refrigerator too close to the wall?
Foods in refrigerating room are frozen
• Isn’t the temperature control lamp of front operating
panel in “HIGH” mode?
• Isn’t the environmental temperature around the
installing place too high?
• Isn’t the watery foods put into the inside of refrigerator
when the cool air is coming out?
Noises and strange sound
• Check if the floor is not flat or not hard.
• Isn’t the rear plate of refrigerator too close to walls?
• Is there any stuffs fallen down at rear or beneath of
refrigerator?
• Isn’t it the sound of compressor within the product?
• The sound of “TICK TICK” from inside of refrigerator
is the one to be heard when various parts are contracted or expanded by cooling operation, therefore it
does not mean any trouble with it.
Too hot at the front corner and side wall areas of
refrigerator. Dew are forming
• This is because heat pipe is installed at the front corner to prevent dew-forming. It is likely to feel that the
temperature on these area is very high in the environmental conditions of high exteior temperature.
However, it does not mean any trouble with it.
• It happens that dews form on the outer wall of refrigerator under the high humidity environment. This is
because the moisture in the air touches the cold surface of refrigerator.
31
SR-608, 606/ENG 11/15/59 4:19 PM Page 33
SYMPTIONS
CHECK
Sound of water flow in refrigerator
• It is the flowing sound of refrigerant that is cooling the
inside of refrigerator.
Smell in the refrigerator
❊ Some smells may be generated in refrigerator or in
ice when in use as follow.
• When preserving meat and fish without any sealing.
• When preserving dried fish such as kettlefish,
anchovies and laver without sealing.
• When preserving foods with sealing by using smelly
vinyl.
Cautions : Use sanitary vinyl envelopes when pre
serving foods by using vinyl envelopes.
There may be often a smell of sterilizing
medicine when making the ice with running
water from the faucet.
Frost on the wall of freezing room
• Isn’t the air exit of freezing room blocked?
• Allow some distance between foods for better air
circulation.
• Isn’t the door closed completely?
Dews in the refrigerating room walls and vegetable
box
• This happens when the environmental humidity is
high or the door is open for a long time or watery
foods are stored without a lid.
• Preserve foods with the lid closed or wraps sealed.
32
SR-608, 606/ENG 11/15/59 4:19 PM Page 34
QUESTIONS
WHAT IS THE LOW TEMPERATURE CATALYZING DEODORIZER?
Low temperature catalyzing deodorizer
1
Low temperature catalyzing deodorizer is installed at cool air suction hole
where the air of refrigerating room is
sucked, therefore, even without any
additional operation, smells are
removed while air is in a natural
circulation.
2
It is so designed as to suck and
completely remove smells. Also it
has an excellent capability of deodorizing the bad smell of the favorate
foods particularly at home.
bad smell
Caution
• Low temperature catalyzing deodorizer has a semi-permanent lifetime.
• The function of low temperature catalyzing deodrizer has no harmful effect on human bodies and is
applied only to remove smells from the stored foods within the refrigerator.
• Use wraps or sealed tank when preserving foods with much smells.
Deodorizing effect may be reduced as the smells are adhered to inner wall of refrigerator or to other
foods.
33
SR-608, 606/ENG 11/15/59 4:19 PM Page 35
MEMO
34
SR-608, 606/ENG 11/15/59 4:19 PM Page 36
ELECTRONICS
Download PDF