SIDE BY SIDE
REFRIGERATOR
OWNER’S MANUAL AND INSTALLATION
CONTENTS
SAFETY WARNING ..............................................................................2
OPERATING INSTRUCTIONS ........................................................4
SETTING UP THE REFRIGERATOR.........................................................4
MAJOR FEATURES .....................................................................................4
CONTROL PANEL........................................................................................5
DIGITAL PANEL...........................................................................................7
TEMPERATURE CONTROL .......................................................................8
ICE AND COLD WATER DISPENSER........................................................8
SHELVES AND BINS ...................................................................................9
FOOD STORAGE GUIDE .........................................................................10
CoolSelect ZoneTM Drawer GUIDE.............................................................12
REMOVING FREEZER ACCESSORIES..................................................14
REMOVING REFRIGERATOR ACCESSORIES .....................................14
BEVERAGE STATIONTM (optional).............................................................15
CLEANING ACCESSORIES......................................................................16
CHANGING THE INTERIOR LIGHT .........................................................16
WATER FILTER ..........................................................................................17
DOORS.......................................................................................................17
INSTALLATION INSTRUCTIONS................................................18
INSTALLATION OF THE REFRIGERATOR .............................................18
REMOVING THE REFRIGERATOR DOORS..........................................19
REATTACHING THE REFRIGERATOR DOORS ....................................22
ADJUSTING THE CLEARANCE BETWEEN THE DOORS ....................25
CHECKING THE WATER DISPENSER LINE...........................................27
INSTALLAING THE WATER DISPENSER LINE.......................................28
TROUBLESHOOTING ...............................................................................33
DA99-00275B REV(0.5)
SAFETY WARNING
WARNING
• Before operating the appliance, please read this manual thoroughly and retain it for your reference.
• Because these following operating instructions cover various models, the characteristics of your
refrigerator may differ slightly from those described in this manual
• The appliance is not intended for use by children or infirm persons without adult supervision.
• Children should be supervised to ensure that they do not play with the appliance.
CAUTION/WARNINGS USED
OTHER SIGNS USED
Represents something you must NOT do.
WARNING
Represents something you must NOT
disassemble.
Indicates that a danger of
death or serious injury exists.
Represents something you must NOT touch.
Represents something you must follow.
CAUTION
Indicates that you must disconnect the
power plug from the socket.
Indicates that a risk of
personal injury or material
damage exists.
Represents a ground is needed to prevent
electric shock.
It is recommended that this sentence be
handled by service man.
WARNINGS
Do not plug several appliances into the same multiple
power board.
• This could cause overheating and the risk of fire.
Do not store volatile or flammable substances in the
refrigerator.
• The storage of benzene, thinner, alcohol, ether, LP gas and
other such products may cause explosions.
Do not disassemble or repair the refrigerator by yourself.
• You run the risk of causing a fire, malfunctions and/or
personal injury.
Pull the power plug out of the socket before changing the interior light of the refrigerator.
• Otherwise, there is a risk of electric shock.
If you wish to dispose of the refrigerator / freezer throw
it away after first removing the doors and seals.
• Do so in a way, that is not possible for a child to remain
trapped inside.
Make sure that the power plug is not squashed or damaged by the back of the refrigerator .
• A damaged power plug may overheat and cause fire.
Do not directly spray water inside or outside the refrigerator/ freezer.
.
• There is a risk of electric shock.
Do not use aerosols near the refrigerator .
• There is a risk of explosion or fire.
Do not bend the power cord excessively or place
heavey articles on it .
• This constitutes a fire hazard. If the power cord is damaged, have it replaced immediately by the manufacturer
or its service agent.
The refrigerator must be grounded.
• You must ground the refrigerator to prevent any power
leakages or electric shocks caused by current leakage
from the refrigerator.
Do not insert the power plug with wet hands.
• You may receive an electric shock.
Never use gas pipes, telephone lines or other potential lightening rods as ground.
• Improper use of the ground plug can result in electric
shock.
Do not put a container filled with water on the refrigerator.
• If spilled, there is a risk of fire or electric shock.
Do not install the refrigerator in a damp place or a
place where it may come in contact with water.
• Deteriorated insulation electrical parts may cause electric
shock or fire.
2
SAFETY WARNING SIGNS
SAFETY WARNING
CAUTIONS
Do not overfill the refrigerator with food.
• When you open the door, an item may fall out and cause
personal injury or material damage.
Do not put bottles or glass containers in the freezer .
• When the contents freeze, the glass may break and
cause personal injury.
If the wall socket is loose, do not insert the power
plug.
• There is a risk of electric shock or fire.
Do not use a wet or damp cloth when cleaning the
plug. Remove any foreign matter or dust from the
power plug pins.
• Otherwise there is a risk of fire.
• If the refrigerator is disconnected from the power
supply, you should wait for at least five minutes
before plugging it back.
Do not disconnect the power cord by pulling on it.
• Damage to the cord may cause a short-circuit, fire
and/or electric shock.
• If the power cord is damaged, it must be replaced by
the manufacturer, a certified service agent or qualified
service personnel.
Do not store articles on the top of the appliance .
• When you open or close the door, the articles may fall
and cause personal injury and/or material damage.
If the refrigerator is not to be used for a long
period of time, pull out the power plug.
• Deterioration in the insulation may cause fire.
Do not store pharmaceuticals products, scientific
materials or temperature-sensitive products in the
refrigerator.
• Products that require strict temperature controls must
not be stored in the refrigerator.
Do not let children hang on the door. If not, a serious injury may occur.
If you smell pharmaceuticals or smoke, pull out the
power plug immediately and contact your SAMSUNG Electronics service center.
Do not touch the inside walls of the freezer or
products stored in the freezer with wet hands.
• This may cause frostbite.
Do not insert your hands into the bottom area
under the appliance.
• Any sharp edges may cause personal injury.
Never put fingers or other objects into the
dispenser hole and ice chute. It may cause personal injury or material damage
3
SETTING UP THE REFRIGERATOR
Once you have performed the following steps, your refrigerator should be fully operational. If not, check
the power supply and electricity source. If you have any questions, contact your SAMSUNG
service center.
Place the refigerator in an appropriate location with reasonable clearance between the
wall and the refigerator.
(refer to installation instructions in this mannal)
Set the temperature control to the coldest
temperature and wait for an hour. The
freezer should get slightly chilled and the
motor should run smoothly.
When the refrigerator is plugged in,
the interior light should come on when
you open the doors.
Once the refrigerator temperature is sufficiently low, you can store food in the
refrigerator. After starting the refrigerator, it
takes a few hours to reach the appropriate
temperature.
MAJOR FEATURES
Twin Cooling System
• The refrigerator and the freezer have two evaporators. Given this
independent system, the freezer and the refrigerator are cooled
individually as required and are, therefore, more efficient. Food odor
from the refrigerator does not affect food in the freezer due to separate of air flow circulation.
Multi-Flow System
• Cool air circulates through multiple vents on every shelf level. This
provides even distribution of cooling inside cabinets to keep your
food fresh longer.
Xtra SpaceTM
• Vertical room next to the ice maker in the freezer provides space
for pizza etc.
Door Alarm
• A beeper reminds you if the door is left open.
Xtra FreshTM
• Optimized humidity control keeps vegetables & fruits fresh.
Deodorizer (optional)
• Reusable deodorizer keeps the refrigerator air fresh and
odor free.
CoolSelect ZoneTM Drawer(optional)
• User can select Quick Cool, Thaw and Select buttons for quickly
chill, thaw and cools items. Select Soft Freeze, Cool or Chill to
control the temperature of drawer.
This operation instruction covers various models.
The characteristics of your appliance may differ slightly from those described in this manual.
NOTE
4
CONTROL PANEL
Basic Model
OPERATING INSTRUCTIONS
Dispenser Model (Child Lock)
Dispenser Model (Moisture Control)
FREEZER TEMP. BUTTON
To set the freezer temperature,
press the button repeatedly to
change the set temperature in
sequence between
-14°C and -25°C
POWER FREEZE BUTTON
Speeds up the freezing process in
the freeze.
ICE TYPE BUTTON
Use this button to choose Cubed
or Crushed Ice or Ice off.
FRIDGE TEMP. BUTTON
To set the fridge temperature,
press the button repeatedly to
change the set temperature in
sequence between 7°C and 1°C.
POWER COOL BUTTON
Speeds up the cooling
process in the refrigerator
MOISTURE CONTROL BUTTON
Initially the light of moisture control button is on. If the moisture in the dispenser or Beverage StationTM is found,
press this button. So the light will be on,
and eliminate the moisture.
5
CHILD LOCK BUTTON
When this button is pressed for
3 sec., the Power Freeze, Power
Cool, Freeze Temp. Fridge
Temp. are locked and can not
be modified. The Water and Ice
dispenser are not locked as to
allow for usage.
CONTROL PANEL
Opitonal
Basic Model (With CoolSelect ZoneTM)
Dispenser Model (With CoolSelect ZoneTM)
Dispenser Model (With CoolSelect ZoneTM)
6
Freezer Temp. indicates the current freezer temperature.
Fridge Temp. indicates the current refrigerator temperature.
Quick Cool, Thaw, and Select show the status of the CoolSelect ZoneTMDrawer
This light is on when you press the Power Freeze button.
Power Freeze • Press this button to quickly return the freezer to the set temperature.
• If you need much ice, you can get ice faster.
• Press the button again to cancel the Power Freezer mode.
Power Cool • This light is on when you press the Power Cool button.
Press the button to quickly return the refrigerator to the set temperature.
Press
the button again to cancel the Power Cool mode.
•
Deodorizer
• This light indicates the recyclable deodorizer is in operation.
• Recycle the honeycomb cartridge once or twice a year (see “Cleaning the
Accessories” section)
Cubed Ice, Crushed Ice and Ice Off
• Press the Ice Type button in seqence to choose
Cubed Ice, Crushed Ice or Ice Off to stop making ice.
• Bright icon indicates the ice state currently operated.
Filter Indicator
• When the green light changes to orange, it is time to replace the water filter.
If indicator is red, quick replacement is strongly recommended.
• When the water filer is replaced, reset the indicator by pressing the Ice Type button and the Child Lock buttons simultaneously for 3 seconds.
• To turn this indicator off, press the Ice Type and Child Lock buttons simultaneously for 5 seconds.
7
OPERATING INSTRUCTIONS
DIGITAL PANEL
TEMPERATURE CONTROL
Freezer
Refrigerator
• The freezer temperature can be set between
• The refrigerator temperature can be set between
7°C and 1°C.
Fridge Temp. button repeatedly until the
desired temperature is shown in the temperature display.
• The temperature display changes in sequence and
reverts in the same way as the freezer.
-14°C and -25°C.
• Press the Freezer Temp. button repeatedly until the
desired set temperature is shown in the temperature
display.
• The temperature display changes in sequence
between -14°C and -25°C. When the display reaches
14°C, it returns to -25°C.
• After five seconds, the display reverts to the actual
freezer temperature. The unit will then work to adjust to
the new desired temperature.
• Press the
• When ice cream is stored above -15°C in freezer, it may melt.
• The temperature of the freezer or the refrigerator rises from frequent openings, when sweeping
WARNING
and from warm food. This may cause the digital display to blink . The digital display will stop
blinking when the freezer and refrigerator return to the normal temperature.
ICE and COLD WATER DISPENSER
Ice Maker (Basic Model)
• Pull out the ice tray.
• Add water until it reaches the water level indicator.
• Put the ice tray back in place.
Water Dispenser
Ice Dispenser
The capacity of the water tank is approximately 1.2l.
The ice maker produces 10 cubes at once and about 120
cubes a day automatically. This quantity may be influenced
by factors such as the freezer temperature, the Power
Freeze function and the number of door openings. When
your refrigerator is plugged in, the Cubed Ice mode is automatically selected .
Cold Water
• Push the water dispenser lever with a cup.
• If you have just installed the refrigerator, throw
away the first six glassfuls of water to flush out
impurities in the water supply system.
Press the Ice Type button to select the type of ice:
• Cubed Ice
• Crushed Ice
Push
• No Ice
No Ice
If the Ice remains in the Ice bucket, the
NOTE cubed ice is obtained.
Push the ice dispenser lever with a cup.
If you have a long vacation or business trip
and won’t use the water or ice dispensers,
CAUTION close the water valve. Otherwise, water
may occur leakage.
• Place a cup in line with the dispenser lever the
dispenser to prevent ice from jumping out.
Push
Never put fingers or any other objects in
the dispenser opening.
WARNING It may cause injury.
8
SHELVES AND BINS
Freezer
Light
Xtra SpaceTM
Door Bin
Light
OPERATING INSTRUCTIONS
Ice Chute
Light Switch
Ice Maker
Glass Shelf
Pockets
Plastic Drawers
Front Leg Cover
Basic Model
Dispenser Model
Refrigerator
Water Filter (optional)
Dairy Compartment
Light (upper)
Wine Shelf (optional)
Spill-proof glass Shelf
Muti-purpose Bin
Light Switch
Foldable Shelf (optional)
Beverage StationTM (optional)
Deodorizer
Lights (lower)
Egg Container
CoolSelect ZoneTM Drawer
or Chilled Bin (optional)
Door Bin Top Lips
Vegetable & Fruit Drawer
Gallon Door Bins
9
FOOD STORAGE GUIDE
Basic Model
Dispenser Model
FROZEN FOOD STORAGE IN FREEZER
Xtra SpaceTM
• Can be used for frozen foods such as pizza, pasta, burri tos, and fajitas.
• In order to prevent odor penetration to the ice, stored food should be
wrapped securely.
Tempered Glass Shelf
• Can be used to store all types of frozen food.
Door Bin
• Can be used for small packages of frozen food.
Plastics Drawer
• Can be used to store meat and dry foods. Stored food should be
wrapped securely using foil or other suitable wrapping materials or containers.
Ice chute
Do not put your fingers, hands or any other in suitable objects in the chute or ice-maker bucket.
as this may result in personal injury or material damage.
WARNING
10
FOOD STORAGE GUIDE
CHILLED FOOD STORAGE IN REFRIGERATOR
Tempered Spill Proof Glass Shelf
• Can be used to store all types of chilled food.
• Safe and hard to break resistant.
• Circular marks on the glass surface are a normal phenomenon.
Chilled Bin or CoolSelect ZoneTM Drawer (optional)
• Helps to preserve the taste of food and prolongs its freshness. Use to
Fruit & Vegetable Drawer (Upper and Lower)
• Is used to store fruits and vegetables.
• This drawer is airtight. Optimized humidity control design helps to preserve the freshness of the stored vegetables and fruits.
NOTE
Without drawers, the fruit & vegetable can be stored.
Dairy Compartment
• Can be used to store butter or margarine.
Gallon Door Bins
• Can be used to store foods in small packages, such as milk and
yogurt.
Beverage Station (optional)
• Can be used to store the frequently used items, such as canned beverages and snacks and allows access to these items without opening
the refrigerator door.
Bottles should be stored tightly together so that they do not fall out.
CAUTION
Egg Container
• Put eggs in the container and place them on the shelf.
Wine Shelf (optional)
• Place your wine bottle on the shelf to maintain their taste.
• If you have a long vacation planned, you must decide to empty the refrigerator and turn it off. Wipe
WARNING
excess moisture from the inside and leave the doors open. Otherwise, odor and mold may develop.
11
OPERATING INSTRUCTIONS
store cheese, meat, poultry, fish or any other foods used quickly.
CoolSelect ZoneTM Drawer GUIDE
“Select” button (Optional)
Soft Freeze
• When “Soft Freeze” is chosen, the temperature on the
digtal panel displays -5oC regardless of the set temperature of the refrigerator.
• “Soft-Freeze” temperature helps keep meats and fishes
fresh longer.
• Can cut meat easily without drips.
Chill
• When “Chill” is chosen, the temperature of the CoolSe•
lect ZoneTM Drawer is kept at -1oC regardless of the set
refrigerator temperature.
“Chill” temperature helps keep meat or fish fresh longer.
Cool
• When “Cool” is chosen, the temperature will be the same
•
as the set temperature of the refrigerator. The digital
panel shows the same temperature as that of the display
panel.
The CoolSelect ZoneTM Drawer allows extra refrigerator
space.
12
CoolSelect ZoneTM Drawer GUIDE
“Quick Cool” button
• You can use the Quick Cool feature with the CoolSelect Zone .
• “Quick Cool” allows 1~3 canned beverages to cool within 60 min.
• To cancel this option, press the “Quick Cool” button again.
TM
•
CoolSelect ZoneTM returns to the previous temperature.
When “Quick Cool” ends, it returns to the “Cool” temperature setting.
OPERATING INSTRUCTIONS
Depending on the beverages, the cool-down time may vary.
NOTE
• For “Quick Cool” option, food stored in the CoolSelect Zone
TM
WARNING
Drawer should be removed.
“Thaw” button
• Drips loss and quality deterioration of meats reduces the freshness of foods.
• After “Thaw” is selected, warm and cold air is alternately sup•
•
•
•
•
plied into the CoolSelect ZoneTM Drawer .
Depending on the weight of meat, thawing time can be selected
for 4 hrs, 6 hrs, 10 hrs, and 12 hrs sequentially.
When “Thaw” ends, CoolSelect ZoneTM display returns to “chill”
condition.
When “Thaw” ends, there are no juice in the meats and they are
half-freezed condition so it is easy to cut them for cooking.
To cancel this option, press any button except “Thaw”.
The approximate thawing time of meat and fish are shown
below. (Based on 1inch thickness)
Thaw Time
Weight
4 hours
400 g
6 hours
600 g
10 hours
800 g
12 hours
1000 g
Depending on the size and thickness of meat and fish, the thawing time may vary.
NOTE
The above weight represents the total weight of food in the CoolSelect ZoneTM Drawer.
Ex) The total thawing time for 400g frozen beef and 600g frozen chicken will be 10 hours.
• With the “Thaw” option, food stored in the CoolSelect Zone
TM
WARNING
13
Drawer should be removed.
REMOVING THE FREEZER ACCESSORIES
Ice maker bucket (optional)
• Remove the bucket by lifting up and pulling out.
Glass shelf
• Pull the shelf out as far as
it goes. Then lift it up and
remove it.
Front leg cover
• Open the freezer and refriger-
Door bin
ator doors, remove three
screws and detach the cover.
• To reassemble the cover leg
front, put it back to original
position and tighten the three screws.
• Hold the door bin with both
hands and then lift it up.
Plastic drawer
• Remove the drawer by
•
pulling it out and lifting it up
slightly.
NOTE
Do not use excessive force when
disassembling the cover. It may cause
an injury.
REMOVING THE REFRIGERATOR ACCESSORIES
Spill Proof glass shelf
• Pull the shelf out as far as it will go. Then lift it up and remove it softly.
Fruit & Vegetable Drawer
• Remove the drawer by holding the handle, pulling the drawer out and lifting it up smoothly..
• Remove the optimized humidity control cover by pulling it towards you.
Gallon Door Bin
• Hold the bin with both hands and remove it by lifting it up.
Wine Shelf (optional)
• It is attached to the cabinet wall. To remove wine shelf, slide the
wine shelf in the direction of the arrow as shown.
• Simply take the shelf out of the tabs.
• Before removing the freezer and refrigerator accessories, please move the stored foods to other space.
WARNING
14
BEVERAGE STATIONTM (optional)
To open the Beverage StationTM, hold the Beverage StationTM door handle and pull it downward.
• The Beverage Station
is convenient
and reduces energy consumption,
because you do not need to open
the refrigerator door to access stored
beverages and snacks.
WARNING
• The door of the Beverage StationTM should never be removed. The Beverage StationTM cannot function if its door
is missing.
• When closing the Beverage StationTM door, be careful not to put your hands or fingers around the door frame
where they can be caught or injured.
• When you use the open door as a tray, do not place heavy objects on it. Do not allow children to
hang on the door because there is a risk of personal injury or material damage.
• When you open the beverage stationTM door, be careful not to hit children head.
CLEANING THE ACCESSORIES
Interior
Clean the accessories with a mild detergent, then wipe out with a dry cloth.
After washing the accessories, make sure that they are dry before using them again.
•
•
Exterior
• Wipe the digital panel and display panel with a clean cloth.
• The doors and handles should be cleaned with a mild detergent and cloth. Dry them with a
clean cloth.
• The exterior part of refrigerator should be polished once or twice a year.
Rear
• Use a vacuum cleaner to remove dust once or twice a year.
Ice and water dispenser (optional)
• Use a damp cloth to clean the ice and water dispenser. Then wipe it out with a dry cloth.
• To keep drainage grid dry, do not touch ice and water dispenser.
Beverage StationTM (optional)
• Use a damp cloth to clean the Beverage StationTM. Then wipe it out with a dry cloth.
Rubber door seals
• If the rubber door seals are dirty, the door will not close properly, The refrigerator will not be
able to function efficiently. Clean the doors with a mild detergent and damp cloth. Wipe with
a dry cloth.
WARNING
• Do not spray the refrigerator with water. It may cause a death by an electric shock.
• Do not clean it with benzene, thinner or car detergent. It may cause a fire.
15
OPERATING INSTRUCTIONS
• It is recommended that you use the
Beverage StationTM for storing most
frequently needed foods
TM
CLEANING THE ACCESSORIES
Deodorizer
• Remove the cover with a flat blade screw driver as shown.
• Take out the cartridge from the cover and soak it in clean, warm water
at least than 4 hrs. Completely dry out the cartridge with sunlight for at least 8 hrs in
an open area.
• Repeat this process once or twice a year.
• If it is dried in a confined area, odor may be spread to that area.
• Keep the children away from yellow water, they may drink water.
NOTE
CHANGING THE INTERIOR LIGHT
Before changing the interior light, unplug the refrigerator from the power supply. If you
have difficulty in changing the light, contact your service center.
WARNING
INTERIOR LIGHT IN THE REFRIGERATOR .
Upper
Pull out the screw cap ➀ and
remove the screw.
Push the lamp cover in the
direction of the arrows.
After changing the bulb,
reattach the light cover
and screw it in again.
Take the lamp cover out in the
direction of the arrows.
After changing the bulb,
reattach the light cover
and screw it again.
Lower (optional)
Pull out the screw cap ➀ and
remove the screw.
16
CHANGING THE INTERIOR LIGHT
INTERIOR LIGHT IN THE FREEZER (Dispenser Model)
Use a screwdriver to remove
the light cover (➀).
Reattach the light cover
To replace freezer and refrigerator light bulbs (Bulb size E14), please contact SAMSUNG dealer.
INTERIOR LIGHT IN THE FREEZER (Basic Model)
Pull out the screw cap ➀ and
remove the screw.
Push the lamp cover in the
direction of the arrows.
After changing the bulb,
reattach the light cover
and screw it in again.
WATER FILTER
The water “Filter Indicator” light
• “Filter Indicator” light lets you know when it is time change your water filter cartridge. The light
will change from green to orange. This tells you that it is almost time to change the current cartridge.
It is recommended that you replace the cartridge when the light changes to red.
(see “Install the water filter” section for more information)
Using the dispenser without the water filter
• You can not use the water and ice dispenser without a water filter cartridge because of the water line
block at the water supply.
Ordering replacement filters
• To order more water filter cartridges, contact your authorized Samsung dealer.
DOORS
The refrigerator doors have a special door opening and closing feature to make sure that the doors
close all the way and are securely sealed.
When opening the door, it will only open so far. After reaching a certain point, it will remain open.
When the door is partially open, it will close automatically .
17
OPERATING INSTRUCTIONS
NOTE
Change the bulb with a new
one (➁)
INSTALLATION OF THE REFRIGERATOR
Checking the Dimensions of your Entrance Door
NOTE
• Check the dimensions of your entrance door to determine whether the refrigerator can pass
through it.
• When refrigerator passes in door and depth or width of refrigerator is bigger, removes
refrigerator doors.
Selecting the Location for the Refrigerator
• Select a location with easy access to the water supply.
• Select a location with enough space for the refrigerator.
• Select a location without direct exposure to sunlight.
Caution
• Before disassembling the freezer door, the water supply line needs to be disconnected.
(If not, the water supply line can be damaged.)
• See “Separating the water supply line from the refrigerator” on the next page.
Allow sufficient space to install the refrigerator on a flat surface.
• If your refrigerator is not level, the internal cooling system may not work correctly.
10 Cm
5 Cm
1 Cm
NOTE
Allow clearance to the right, left, back and top when installing the refrigerator.
This has the advantage of reducing power consumption.
18
REMOVING THE REFRIGERATOR DOORS
Removing the Front Leg Cover (Optional)
Open the freezer and refrigerator doors, and then take off the front leg cover assembly by turning the three screws counter-clockwise.
a
FRONT LEG COVER
Separating the water supply line from the refrigerator (Optional)
1) Remove the screw from clamp ( a ).
2) Remove the water tube by pressing the coupler (➁) and pulling the water tube (➀) away.
WARNING
Do not cut the water tube but separate it from the coupler.
19
INSTALLATION INSTRUCTIONS
SCREW
REMOVING THE REFRIGERATOR DOORS
NOTE
• Lift the door straight up.
• Be careful not to pinch the water tubing and wire harness on the door.
• Place doors on a protected surface.
Removing the Freezer Door
1) With the door closed, remove the upper hinge cover (➀) using a screwdriver, and then disconnect the wires (➁).
2) Remove hinge screws (➂) and ground screw (➃) counter-clockwise, and take off the upper
hinge (➄) along the arrow (➅). Take care when removing the door to ensure that it does not
fall on you.
3) Remove the door from the lower hinge (➆) by
carefully lifting the door (➇).
20
4) Remove the lower hinge (➈) from the bracket
lower hinge (➉) by lifting the lower hinge (➈) in
the direction of the arrow.
REMOVING THE REFRIGERATOR DOORS
Removing the Refrigerator Door
1) With the door closed, remove the upper hinge cover (➀) using a screwdriver, and then disconnect the wires (➁).
3) Remove the door from the lower hinge (➆) by
lifting the door (➇).
4) Remove the lower hinge (➈) from the bracket
lower hinge (➉) by lifting the lower hinge (➈)
in the direction of the arrow.
21
INSTALLATION INSTRUCTIONS
2) Remove hinge screws (➂) and ground screw (➃) counter-clockwise, and take off the upper
hinge (➄) in the direction of the arrow (➅). Take care when removing the door to ensure that it
does not fall on you.
REATTACHING THE REFRIGERATOR DOORS
Reattaching the Freezer Door
1) Insert the lower hinge (➀) in the bracket
lower hinge (➁).
2) Reattach the freezer door by inserting the
hose (➂) in the lower side of the door into
the hole in the lower hinge (➃) and pulling
the hose down.
3) Insert the upper hinge shaft (➄) into the hole (➅). After levelling between the upper hinge hole
(➆) and the hole of the cabinet (➇). Reattach bolts (➈) and screw (➉) in a clockwise direction.
4) Connect the wires.
5) Put the front part of the upper hinge cover ( 11 )
on the front part of the upper hinge ( 12 ) and
reattach from the front part of the upper hinge
cover first.
22
REATTACHING THE REFRIGERATOR DOORS
Reattaching the Refrigerator Door
1) Insert the lower hinge (➀) in the bracket
lower hinge (➁).
2) Place the hole in the refrigerator door (➂)
over the lower hinge (➃).
4) Connect the wires.
5) Put the front part of the upper hinge cover (11 )
on the front part of the upper hinge ( 12 ) and
reattach it from the front part of the upper
hinge cover first.
23
INSTALLATION INSTRUCTIONS
3) Insert the upper hinge shaft (➄) into the hole (➅). After levelling between the upper hinge hole (➆)
and the hole of the cabinet (➇). Reattach hinge screws (➈) and screw (➉) in the clockwise direction.
REATTACHING THE REFRIGERATOR DOORS
Reattaching the Water Tube (Optional)
1) While pressing the front face of coupler (➁), insert the water line (➀) in the coupler.
2) Tighten the screw on the clamp ( a ).
a
Reattaching the Front Leg Cover (Optional)
Put on the front leg cover by turning the three screws clockwise, as shown in the figure.
FRONT LEG COVER
SCREW
24
ADJUSTING THE CLEARANCE BETWEEN THE DOORS
Please level the refrigerator first.
The doors will be uneven if the refrigerator is not level.
DIFFERANCE OF HEIGHT
Case 1) Freezer door is lower than
that of the refrigerator
Insert a straight screwdriver (-) (➀) into a slot of the
control lever (➁), turn it clockwise and level the
refrigerator.
➁ CONTROL LEVER
DIFFERANCE OF HEIGHT
Case 2) Freezer door is higher than
that of the refrigerator
Insert a straight screwdriver (-) (➀) into a slot of the
control lever (➁), turn it clockwise and level
the refrigerator.
➀ DRIVER(-)
➁ CONTROL LEVER
Do not make small adjustment by turning the control lever, Please refer to the next page.
NOTE
25
INSTALLATION INSTRUCTIONS
➀ DRIVER(-)
ADJUST THE CLEARANCE BETWEEN THE DOORS
Making small adjustments between doors.
If the door of the freezer is lower than that of
the refrigerator.
If the door of freezer is higher than that of the
refrigerator.
Adjustment part
Adjustment part
Please open the doors and adjust the doors as follows:
1) Release the nut (①) on the lower hinge until the upper end of the bolt (➁).
When you release the nut(①), use enclosed hex wrench (➂) to turn the bolt(➁) a little counter
clockwise to make the nut(①) loose with your fingers.
NOTE
➂ WRENCH
➂ WRENCH
➀ NUT
➀ NUT
➁ BOLT
➁ BOLT
2) Please adjust the height difference between the doors turning the bolt (➁) turn clockwise(
clockwise (
).
When you turn clockwise (
) or counter
), the door goes up.
NOTE
➂ WRENCH
➂ WRENCH
➁ BOLT
➁ BOLT
3) After adjusting the doors, turn the nut (①) turn clockwise(
en the bolt again with the wrench (➂) to fix the nut(①).
) until the lower end of the bolt, then tight-
➂ WRENCH
➂ WRENCH
➀ NUT
➀ NUT
➁ BOLT
If you do not fix the nut (①)firmly, the bolt (➁) may be released.
NOTE
26
➁ BOLT
CHECKING THE WATER DISPENSER LINE (Optional)
1) In order to operate the ice maker properly, water pressure of 1.4 ~ 10 kgf/cm2 is required.
In this range a 100 cc paper cup can be filled in 10 seconds.
2) The water filter removes particles. It does not sterilize or destroy any micro-organisms.
3) If the refrigerator is installed in an area with low water pressure (below 1.4kgf/cm2), you should install
a booster pump to compensate for the low pressure.
4) Ensure the water storage tank inside the refrigerator is preperly filled initially. Push the water dis
penser lever until the water runs from the outlet.
A universal water supply kit is available at extra cost from your dealer. The refrigerator manufacturer
recommends using a water supply kit containing copper tubing.
NOTE
Checking the Parts
(Interior model)
Sealing tape
Clip A x 8EA
Tapping screw x 12EA
Purifier lock
station
Water line
Tightening band
Purifier
(Exterior model)
27
INSTALLATION INSTRUCTIONS
Purifier
INSTALLING OF THE WATER DISPENSER LINE
For Interior Model
(Case 1)
Connecting to water supply line
1. Cold Water line
2. Pipe Clamp.
3.Copper (or Plastic) line
4.Compression Nut
5.Compression Sleeve
6.Shut Off Valve
7.Packing Nut.
- Shut off the main water supply line and turn the Ice maker to
the off position.
- Locate the nearest cold drinking water line.
- Follow the instructions in the ice maker installation kit.
Connect the water line to the refrigerator
- Slip the compression nut and plastic ferrule
through the plastic tube.
- After inserting the sleeve, tighten the compression nut onto 1/4” compression fitting(union).
NOTE
Compression Nut
Ferrule
Sleeve
Do not overtighten the compression
nut.
Compression fitting
- Slip the compression ferrule and nut on copper (or plastic) tubing as shown.
Tighten the comperssion nut onto the compression fitting(union).
- Turn water on and check for any leakege.
NOTE
Ferrule
Compression Nut
Waterline must be connected to drinkable water only
(Case 2)
Check the water supply line
Connect the water pipe with coupler and tap.
- Close the main water tap.
- Connect coupler “A” to the tap.
- Every join should be protected with sealing tape.
WARRANTY INFORMATION
This water line installation is not covered by the refrigerator or ice maker manufacturer's warranty.
Follow these instructions carefully to minimise the risk of
expensive water damage.
CAUTION
The water line must be connected to the cold water pipe.
If it is connected to the hot
water pipe, it may cause the purifier to malfunction.
COUPLER “A”
Note:
If the coupler does not fit on the current tap, go
the nearest authorised service dealer and purchase
the right couplers fittings.
28
TAP
INSTALLING THE WATER DISPENSER LINE
Connect the water line to the refrigerator.
WATER LINE
CONNECTION NUT
- Remove the compressor cover of the refrigerator.
- Connect the water line to the valve, as shown in the figure.
- When connected, check if there is any leakage.
If any, repeat the connection.
- Reattach the compressor cover of the refrigerator.
COMPRESSOR COVER OF
REFRIGERATOR
Secure the water line.
- Using clip ”A”, fix the water line to the wallor (the back of
refrigerator).
- When the water line is secure, make sure whether the
water line is not excessively bent, pinched or squashed.
CLIP A
WATER LINE
Complete the installation of the water supply line.
INSTALLATION INSTRUCTIONS
- Power on the refrigerator and press the lever on the right of the
dispenser until water runs out through the water line and all air has been empty.
- At this time, check for any possible leakages at the join point in the water line.
After securing the water line, move the refrigerator to the required location.
Once the refrigerator is in position, do not move possibly.
Install the water filter.
- As shown, separate the fixed cap in the refrigerator by rotating
it counterclockwise.
Remove the water filter from the box and put a month indicator
sticker on the filter as shown.
- Write the month you installed the filter on the label.
EX) If the water filter was installed in March, put “MAR”
- Remove the protective cap then position and insert the filter as shown,
- Slowly turn the water filter clockwise 90º to align the indication mark on the
cover, locking the filter in postion. Do not overtighten.
COVER FILTER
SEPARATION
OF RED CAP
ALIGN THE INDICATION MARK
WITH LOCK POSITION.
STICKER
(MONTH INDICATION)
Please check if the indication line aligns with the lock position.
Caution
29
INSTALLING THE WATER DISPENSER LINE
For Exterior model
Connect to the water supply line
CAUTION
Connect the water pipe with coupler and tap.
- Close the main water tap.
- Connect coupler “A” to the tap.
- Every join should be protected with sealing tape.
The water line must be connected to the cold water pipe.
If it is connected to the hot
water pipe, it may cause the purifier to malfunction.
WARRANTY INFORMATION
This water line installation is not covered by the refrigerator or ice maker manufacturer's warranty.
Follow these instructions carefully to minimise the risk of
expensive water damage.
COUPLER “A”
Note:
If the coupler does not fit on the current tap, go
the nearest authorised service dealer and purchase
the right couplers fittings.
TAP
Select the location where the purifier is to install. (Model with the purifier)
LINE
OUTLET
- Cut the water line attached to the purifier
to the appropriate place after measuring
the distance between the purifier and the
cold water tap.
90 degree
SIDE OF
PURIFIER
REFERENCE
- If you wish to reassemble the water inlet
and outlet sides of the purifier during purifier installation, see the reference illustration.
PURIFIER
WATER
WATER INLET SIDE
OF PURIFIER
COUPLER
Remove any residual matter inside the purifier. (Model with the purifier)
- Open the main water tap to check whether water
is running through the water tube on the water
inlet side of the purifier.
OUTLET SIDE
OF PURIFIER
PURIFIER
- If water does not come out through the line,
check whether the tap is open.
- Leave the tap open until clean water is running
out and any residual matter that built up during
manufacturing has been removed.
30
WATER LINE
WATER
INSTALLING THE WATER DISPENSER LINE
Attach the purifier lock stations.
TWO PURIFIER LOCK
STATION
- Hold the purifier lock stations in the appropriate position
(under the sink for example) and fix it tightly into place
where to screw.
TWO PURIFIER LOCK
STATION
WATER TUBE
Secure the purifier in position.
- Fix the purifier in position, as shown in the figure
on the right.
PURIFIER
TIGHTENING
BAND
Connect the water line to the refrigerator.
WATER LINE
CONNECTION NUT
- Remove the compressor cover of the refrigerator.
- Connect the water line to the valve, as shown in the figure.
- When connected, check if there is any leakage.
If any, repeat the connection.
- Reattach the compressor cover of the refrigerator.
COMPRESSOR COVER OF
REFRIGERATOR
Secure the water line.
- Using clip ”A”, fix the water line to the wallor (the back of
refrigerator).
- When the water line is secure, make sure whether the water
line is not excessively bent, pinched or squashed.
31
CLIP A
WATER LINE
INSTALLATION INSTRUCTIONS
PURIFIER
LOCK STATIONS
INSTALLING THE WATER DISPENSER LINE
Remove any residual matter inside the water supply line
1) Turn on the main water supply & shut-off valve of the water
supply line.
2) Run water through the dispenser until the water runs clear
(6~7 minutes). This will clean the water supply system and
clear air from the lines.
3) Additional flushing may be required in some households.
4) Open the refrigerator door and check if water leaks around
the water filter.
NOTE
WATER
ICE
• A newly-installed water filter cartridge may cause water to briefly spurt from the dispenser.
• Before reinstalling the water filter, remove the wine shelf.
Check the amount of water supplied to the ice tray.
1) Lift up (①) and pull out (➁) the ice maker bucket in the freezer.
ICE MAKER
2) When you press the test button, the ice cube container is
filled with water from the water supply tap.
Check the amount of water (see the illustration below).
If the water level is too low,
the ice cubes will be small.
CHECK THE WATER LEVEL
This is not a problem with the ice maker
but of the water pressure in
the pipe, and occurs frequently.
When this problem occurs, contact
the dealer service center to check the
amount of water supplied.
TEST BUTTON
TOO HIGH
OPTIMUM
LEVEL
TOO LOW
32
TROUBLESHOOTING
The refrigerator does not work at all or it does not Ice is not dispensed
chill sufficiently
• Did you stop the ice making function?
• Check that the power plug is properly connected.
• Is there any ice in the ice storage unit?
• Is the temperature control on the display panel set to • Is the water line connected and the shut-off valve
the correct temperature? Try seting it to a lower temopen?
perature.
the freezer temperature too warm?
• Is the refrigerator in direct sunlight or located near a • Is
(Set the temperature lower)
heat source?
• Did you wait for 12 hours after installation of the
• Is the back of the refrigerator too close to the wall?
water supply line before making ice?
The food in the refrigerator is frozen
the correct temperature? Try seting it to a warmer
temperature.
• Is the temperature in the room too low?
• Did you store the food with a high water content in
the coldest part of the refrigerator.
You can hear unusual noise or sounds
• Check that the floor is levelled and stable.
• Is the back of the refrigerator too near to the wall?
• Was anything dropped behind or under the refrigerator?
• A “ticking” sound may be heard from inside the refrigerator, but this is normal. This occurs because various accessories are contracted or expanded.
The front corners and sides of the cabinet are hot;
condensation occurs.
• Anti-condensators are installed in the front corners of
the refrigerator to prevent condensation.
• Condensation can occur when you leave the door
open for a long time.
You can hear water bubbling in the refrigerator
• The bubbling comes from the refrigerant circulating in
the refrigerator and is normal.
There is a bad smell in the refrigerator
• Wrap food with a strong smell so that it is airtight.
Throw away any rotten food.
Frost forms on the wall of the freezer
• Is the air vent blocked?
• Allow sufficient space between the foods stored for
efficient air circulation.
• Is the door closed properly?
No water is supplied
• Is the water line connected and the shut-off valve
open?
• Is the water supply line crushed?
• Is the water tank frozen because the refrigerator temperature is too low? Select a warmer setting on the
display panel.
33
INSTALLATION INSTRUCTIONS
• Is the temperature control on the display panel set to
MEMO
MEMO
Ambient Room Temperature Limits
This appliance is designed to operate at the ambient temperatures specified by its temperature
class marked on the rating plate.
Temperature
Class
Extended Temperate
Symbol
Ambient Temperature
Maximum
Minimum
SN
32°C (90°F)
10°C (50°F)
Temperate
N
32°C (90°F)
16°C (61°F)
Subtropical
ST
38°C (100°F)
18°C (64°F)
T
43°C (109°F)
18°C (64°F)
Tropical
NOTE: The internal temperature may be affected by such factors as the location of the appliance,
ambient temperature and the frequency with which you open the doors.
Adjust the temperature as required to compensate for these factors.
Download PDF

advertising