Samsung | SGH-E370 | Samsung SGH-E370 User Manual

E370.book Page 2 Tuesday, April 18, 2006 5:40 PM
SGH-E370
User’s Guide
E370.book Page 3 Tuesday, April 18, 2006 5:40 PM
Drive safely at all times
Do not use a hand-held phone while driving. Park
the vehicle first.
Switch off the phone when refuelling
Important
safety
precautions
Failure to comply with the following
precautions may be dangerous or illegal.
Do not use the phone at a refuelling point (service
station) or near fuels or chemicals.
Switch off in an aircraft
Wireless phones can cause interference. Using them
in an aircraft is both illegal and dangerous.
Switch off the phone near all medical
equipment
Hospitals or health care facilities may be using
equipment that could be sensitive to external radio
frequency energy. Follow any regulations or rules in
force.
Interference
All wireless phones may be subject to interference,
which could affect their performance.
E370.book Page 1 Tuesday, April 18, 2006 5:40 PM
Accessories and batteries
Meet any special regulations in force in any area and
always switch off your phone whenever it is forbidden
to use it, or when it may cause interference or danger.
Use only Samsung-approved batteries and
accessories, such as headsets and PC data cables.
Useof any unauthorised accessories could damage you
oryour phone and may be dangerous.
Water resistance
Your phone is not water-resistant. Keep it dry.
Sensible use
Use only in the normal position (held to the ear). Avoid
unnecessary contact with the antenna when the phone
is switched on.
Emergency calls
Key in the emergency number for your present
location, then press
.
Keep your phone away from small children
Keep the phone and all its parts, including accessories,
out of the reach of small children.
Important safety precautions
Be aware of special regulations
• The phone could explode if the battery is replaced with an
incorrect type.
• Dispose of used batteries according to the manufacturer’s
instructions.
At very high volumes, prolonged listening to a
headset can damage your hearing.
Qualified service
Only qualified service personnel may repair your
phone.
For more detailed safety information, see "Health and
safety information" on page 88.
1
E370.book Page 2 Tuesday, April 18, 2006 5:40 PM
About this Guide
This User’s Guide provides you with condensed
information about how to use your phone. To quickly
learn the basics for your phone, please refer to “Get
started” and “Step outside the phone.”
In this guide, the following instruction icons appear:
Indicates that you need to pay careful attention
to the subsequent information regarding safety
or phone features.
Indicates that you can get more information on
the referenced page.
→
Indicates that you need to press the Navigation
keys to scroll to the specified option and then
select it.
[
]
< >
2
Indicates a key on the phone. For example,
[
]
Indicates a soft key, whose function is displayed
on the phone screen. For example, <Menu>
•
Camera and camcorder
Use the camera module on your
phone to take a photo or record a
video.
Special features of your phone
•
Music player
Play MP3 music files using your
phone as an Music player.
•
Web browser
Access the wireless web to get upto-the-minute information and a
wide variety of media content.
E370.book Page 3 Tuesday, April 18, 2006 5:40 PM
•
•
Get personal with photo caller
ID
See who’s calling you when the
phone displays their very own
photo displays.
Name card
Create name cards with your
number and profile. Whenever
introducing yourself to others, use
this convenient electronic name
card.
•
Multimedia message service (MMS)
Send and receive MMS messages with a
combination of text, images, video, and audio.
•
E-mail
Send and receive e-mails with images, video, and
audio attachments.
•
Java game
Enjoy Java™-based embedded
games and download new games.
•
Calendar
Keep track of your daily, weekly,
and monthly schedule.
•
Voice recorder
Record memos or sounds.
Special features of your phone
•
Bluetooth
Send photos, images, videos, and
other personal data, and connect
to other devices using free,
wireless Bluetooth technology.
3
E370.book Page 4 Tuesday, April 18, 2006 5:40 PM
Contents
Unpack
6
Make sure you have each item
Your phone
6
Keys, features, and locations
Get started
16
17
18
19
20
21
Enter text
23
ABC, T9, Number, and Symbol modes
7
Call functions
First steps to operating your phone
Advanced calling features
Install and charge the phone ..................................... 7
Power on or off........................................................ 8
Keys and display ..................................................... 9
Access menu functions ............................................ 11
Customise your phone............................................. 12
Make/Answer calls .................................................. 14
Menu functions
Step outside the phone
14
Begin with your camera, the Music player, the web, and
other special features
Use the camera ...................................................... 14
Play music ............................................................. 15
4
Browse the web......................................................
Use Phonebook ......................................................
Send messages ......................................................
View messages.......................................................
Use Bluetooth ........................................................
Quickly launch menus by number .............................
25
29
All menu options listed
Solve problems
86
Help and personal needs
Health and safety information
88
Index
95
E370.book Page 5 Tuesday, April 18, 2006 5:40 PM
Overview of menu functions
To access Menu mode, press <Menu> in Idle mode.
1 Call records
p.29
3 Applications
p.35
5 Messages
p.45
1
2
3
4
5
6
7
p.29
p.30
p.30
p.30
p.30
p.30
p.31
1 Music Player
2 Voice recorder
3 Java world
4 World time
5 Alarm
6 Calculator
7 Converter
8 Timer
9 Stopwatch
10 SIM-AT*
p.35
p.37
p.38
p.39
p.40
p.40
p.41
p.41
p.42
p.42
1
2
3
4
5
6
7
p.45
p.49
p.53
p.54
p.55
p.61
p.61
4 Browser
p.42
1
2
3
4
5
6
p.42
p.43
p.44
p.44
p.44
p.45
Recent contacts
Missed calls
Dialled calls
Received calls
Delete all
Call time
Call costs*
2 Phonebook
p.31
1
2
3
4
5
6
7
8
9
p.31
p.32
p.32
p.33
p.34
p.34
p.35
p.35
p.35
Contact list
FDN list
Add new contact
Group
Speed dial
My name card
Own number
Management
Service number*
Home
Bookmarks
Goto URL
Clear cache
Profile settings
Current profile
Create new message
My messages
Templates
Delete all
Settings
Broadcast messages
Memory status
6 File manager
p.61
1
2
3
4
5
6
p.62
p.63
p.63
p.64
p.65
p.65
Images
Videos
Music
Sounds
Other files
Memory status
7 Calendar
p.65
8 Camera
p.69
9 Settings
p.74
1 Time & Date
2 Phone settings
3 Display settings
4 Sound settings
5 Light settings
6 Network services
7 Bluetooth
8 Security
9 Memory status
10 Reset settings
11 VOD settings**
p.74
p.75
p.77
p.78
p.79
p.80
p.82
p.84
p.85
p.86
p.86
* Shows only if supported by your
SIM card.
** Shows only if supported by your
service provider.
5
E370.book Page 6 Tuesday, April 18, 2006 5:40 PM
Unpack
Your phone
Make sure you have each item
Keys, features, and locations
Earpiece
Camera lens
Phone
Travel Adapter
Display
Web access/
Confirm key
Left soft key
Volume keys
Battery
User’s Guide
You can obtain various accessories from
your local Samsung dealer.
The items supplied with your phone
and the accessories at your Samsung
dealer may vary, depending on your
country or service provider.
6
Dial key
Navigation keys
(Up/Down/Left/
Right)
Right soft key
Power on/off/
Menu exit key
Correct key
Alphanumeric
keys
Special
function keys
Microphone
Headset jack
Camera key
E370.book Page 7 Tuesday, April 18, 2006 5:40 PM
Get started
Reattach the battery.
First steps to operating your phone
Plug the travel adapter
into the phone.
SIM card information
When you subscribe to a cellular network, you receive
a plug-in SIM (Subscriber Identity Module) card
loaded with your subscription details, such as your
PIN, and available optional services.
Install and charge the phone
Remove the battery.
Insert the SIM card.
Plug the adapter into a standard AC wall outlet.
When the phone is completely charged, unplug the
adapter from the power outlet.
If the phone is already on,
first turn it off by pressing
and holding [ ].
Make sure that the goldcoloured contacts on the
card are face down.
7
E370.book Page 8 Tuesday, April 18, 2006 5:40 PM
Get started
Remove the adapter from the phone.
Power on or off
Switch on
1. Open the phone.
2. Press and hold [
Do not turn on the
phone when
mobile phone use
is prohibited.
Low battery indicator
When the battery is low:
• a warning tone sounds,
• the battery low message displays, and
• the empty battery icon
blinks.
If the battery level becomes too low, the phone
automatically turns off. Recharge your battery.
].
3. If necessary, enter the PIN and
press <OK>.
1. Open the phone.
Switch off
2. Press and hold [
].
Keypad lock
When you close the phone, the keypad lock feature
locks the exposed keys so that nothing will happen if
the keys are accidentally pressed.
To unlock the keypad, press <Unlock> and press
<OK>.
8
E370.book Page 9 Tuesday, April 18, 2006 5:40 PM
Keys and display
Keys
In Idle mode, access your favourite
menus directly.p. 75
In Menu mode, scroll through menu
options.
In Idle mode, launch the web browser.
In Menu mode, select the highlighted
menu option.
Delete characters from the display or an
item in an application.
Make or answer a call.
In Idle mode, retrieve numbers recently
dialled, missed, or received.
Press and hold to switch the phone on
and off.
End a call.
In Menu mode, cancel input and return
the phone to Idle mode.
Get started
Perform the function indicated on the
bottom line of the display.
Enter numbers, letters, and some special
characters.
In Idle mode, press and hold [1] to
access your voicemail server. Press and
hold [0] to enter an international call
prefix.
Enter special characters.
In Idle mode, press and hold [ ] to
activate or deactivate Quiet mode. Press
and hold [ ] to insert a pause between
numbers.
Adjust the phone volume.
In Idle mode, with the phone open,
adjust the keypad tone volume. With the
phone closed, press and hold to turn on
the backlight.
In Idle mode, press and hold to turn on
the camera.
In Camera mode, take a photo or start
recording a video.
9
E370.book Page 10 Tuesday, April 18, 2006 5:40 PM
Get started
Display
New text message
Layout
Icons
display various icons.
Text and graphics
display messages,
instructions, and
information you enter.
Menu
Icons
*
Contacts
Soft key function
indicators
show the current functions
assigned to the soft keys.
Received signal strength
EDGE network
Call in progress
Out of your service area; you
cannot send or receive calls
Home Zone, if you have
registered for the appropriate
service
10
New multimedia message
New e-mail
New voicemail
Call diverting feature active
p. 80
Bluetooth active p. 82
Alarm set p. 40
Call ringer settings p. 78
• No indicator: Melody
•
: Vibration
•
: Vibration then melody
•
: Melody then vibration
Quiet mode
Battery power level
* Depending on your country or service provider, the icons shown
on the display may vary.
E370.book Page 11 Tuesday, April 18, 2006 5:40 PM
Access menu functions
The roles of the soft keys vary
depending on the function you are
using. The bottom line of the
display indicates their current role.
Select
Press the left
soft key to select
the highlighted
option.
Select an
option
1. Press a desired soft key.
2. Press the Navigation keys to
move to the next or previous
option.
Get started
Use the soft
keys
3. Press <Select> or [
] to
confirm the function displayed
or option highlighted.
Back
4. To exit, choose either of the
following methods.
• Press <Back> to move up
one level.
• Press [ ] to return to Idle
mode.
Press the right
soft key to return
to the previous
menu level.
Use shortcuts
Press the number key
corresponding to the option you
want.
11
E370.book Page 12 Tuesday, April 18, 2006 5:40 PM
Get started
Customise your phone
Display
language
1. In Idle mode, press <Menu>
and select Settings → Phone
settings → Language.
Idle mode
wallpaper
1. In Idle mode, press <Menu>
and select Settings → Display
settings → Wallpaper.
2. Select a language.
Call ringer
melody
1. In Idle mode, press <Menu>
and select Settings → Sound
settings → Incoming call →
Ring tone.
2. Select a ringtone category.
3. Select a ringtone.
4. Press <Save>.
You can set wallpaper for the idle
screen on the display.
2. Select an image category.
3. Select an image.
Menu mode
skin colour
You can change the colour for the
display components, such as title
bars and highlight bars.
1. In Idle mode, press <Menu>
and select Settings → Display
settings → Skin.
2. Select a colour pattern.
12
E370.book Page 13 Tuesday, April 18, 2006 5:40 PM
Menu
shortcuts
1. In Idle mode, press <Menu>
and select Settings → Phone
settings → Short cut.
2. Select a key.
3. Select a menu to be assigned to
the key.
Quiet mode
You can switch the phone to Quiet
mode to avoid disturbing other
people.
Press and hold [ ] in Idle mode.
Phone lock
You can protect the phone against
unauthorised use with a phone
password. The phone will require
the password on power-up.
Get started
You can set the Navigation keys to
function as shortcuts to access
your favourite menus.
1. In Idle mode, press <Menu>
and select Settings →
Security → Change
password.
2. Enter the default password,
00000000 and press <OK>.
3. Enter a new 4- to 8-digit
password and press <OK>.
4. Enter the new password again
and press <OK>.
5. Select Phone lock.
6. Select Enable.
7. Enter the password and press
<OK>.
13
E370.book Page 14 Tuesday, April 18, 2006 5:40 PM
Make/Answer calls
Make a call
Step outside the phone
1. In Idle mode, enter an area
code and phone number.
Begin with your camera, the Music player, the web, and
other special features
2. Press [
Use the camera
].
3. To end the call, press [
Answer a call
1. When the phone rings, press
[ ].
2. To end the call, press [
Adjust the
volume during
a call
].
Take a photo
1. Open the phone.
2. In Idle mode, press and hold
[ ] to turn on the camera.
].
3. Aim the lens at the subject and
make any desired adjustments.
Press [ / ].
4. Press [
] or [ ] to take a
photo. The photo is saved
automatically.
5. Press <Back> to take another
photo.
View a photo
14
1. In Idle mode, press <Menu>
and select File manager →
Images → Photos.
2. Select the photo you want.
E370.book Page 15 Tuesday, April 18, 2006 5:40 PM
Record a video 1. In Idle mode, press and hold
[ ] to turn on the camera.
3. Press [
] or [
recording.
Copy MP3 files
to the phone
Use these methods:
• Download from the wireless
webp. 42
• Download from a computer
using Samsung PC Studio
Samsung PC Studio User’s
Guide
• Receive via Bluetooth p. 84
Create a play
list
1. In Idle mode, press <Menu>
and select Applications →
Music Player.
] to start
4. Press [
], < >, or [ ] to
stop recording. The video is
saved automatically.
5. Press <
video.
Play a video
> to record another
1. In Idle mode, press <Menu>
and select File manager →
Videos → Videos.
2. Select the video you want.
Step outside the phone
2. Press [1] to switch to Record
mode.
Play music
2. Press <Options> and select
Add to list → Add all or Add a
file.
3. For Add a file, press [
] to
select the files you want and
press <Add>.
15
E370.book Page 16 Tuesday, April 18, 2006 5:40 PM
Step outside the phone
4. Press <Back> to return to the
Music player screen.
Play MP3 file
1. From the Music player screen,
press [
].
2. During playback, use the
following keys:
•
: pauses/resumes
playback.
• Left: returns to the previous
file. Moves backward in a
file when held down.
• Right: skips to the next file.
Skips forward in a file when
held down.
• Up: opens the play list.
•
/ : adjusts the volume.
• Down: stops playback.
16
Browse the web
Using a built-in web browser, you can easily access the
wireless web to get a variety of up-to-date services
and information and to download web content.
Launch the
web browser
In Idle mode, press [
Navigate the
web
•
•
•
•
•
].
To scroll through browser items,
press the Navigation keys.
To select an item, press < >.
To return to the previous page,
press <Back> or [C].
To return to the homepage,
press and hold [C].
To access options, press [ ] or
select
on the top of the
screen.
E370.book Page 17 Tuesday, April 18, 2006 5:40 PM
Use Phonebook
Find an entry
To the phone’s memory:
2. Enter the first few letters of the
name you want.
1. In Idle mode, enter a phone
number and press <Save>.
3. Select an entry.
2. Select Phone → a number type.
3. Specify contact information:
First name, Last name, Mobile,
Home, Office, Fax, Other, Email,
Graphic ID, Alert, Group, and
Notes.
4. Press [
] to save the entry.
To the SIM card:
1. In Idle mode, enter a phone
number and press <Save>.
2. Select SIM.
3. Enter a name.
4. Press [
] to save the entry.
Step outside the phone
Add an entry
1. In Idle mode, press
<Contacts>.
4. Scroll to a number, and press
[
] to dial or press [
] to
edit contact information.
Create and
send a name
card
1. In Idle mode, press <Menu>
and select Phonebook → My
name card.
2. Specify your contact
information.
3. Press [
card.
] to save the name
4. To send the name card to other
people, press <Options> and
select Send via → a sending
method.
17
E370.book Page 18 Tuesday, April 18, 2006 5:40 PM
Step outside the phone
Send messages
1. In Idle mode, press <Menu>
Send a text
and select Messages → Create
message (SMS)
new message → Text
message.
2. Enter the message text.
3. Press <Options> and select
Send only or Save and send.
4. Enter destination numbers.
5. Press [
] to send the
message.
Send a
multimedia
message
(MMS)
1. In Idle mode, press <Menu>
and select Messages → Create
new message → Multimedia
message.
2. Select Subject.
3. Enter the message subject and
press [
].
4. Select Picture & Video or
Sound and add a media file.
5. Select Message.
6. Enter the message text and
press [
].
7. Press <Options> and select
Send.
8. Enter destination numbers or
addresses.
9. Press [
] to send the
message.
18
E370.book Page 19 Tuesday, April 18, 2006 5:40 PM
View messages
2. Select Subject.
View a text
message
From the Inbox:
4. Select Message.
1. In Idle mode, press <Menu>
and select Messages → My
messages → Inbox.
5. Enter the e-mail text and press
[
].
6. Select File attach.
8. Press <Options> and select
Send.
9. Enter e-mail addresses.
10. Press [
] to send the e-mail.
1. Press <View>.
2. Select the message from the
Inbox.
3. Enter the e-mail subject and
press [
].
7. Add image, video, sound, or
music files.
When a notification appears:
Step outside the phone
Send an e-mail 1. In Idle mode, press <Menu>
and select Messages → Create
new message → Email.
2. Select a text message.
View a
multimedia
message
When a notification appears:
1. Press <View>.
2. Select the message from the
Inbox.
19
E370.book Page 20 Tuesday, April 18, 2006 5:40 PM
Step outside the phone
Use Bluetooth
From the Inbox:
1. In Idle mode, press <Menu>
and select Messages → My
messages → Inbox.
Your phone is equipped with Bluetooth technology,
enabling you to connect the phone wirelessly to other
Bluetooth devices and exchange data with them, talk
hands-free, or control the phone remotely.
2. Select a multimedia message.
View an e-mail 1. In Idle mode, press <Menu>
and select Messages → My
messages → Email box.
2. Press <Select> when Check
new mail is highlighted to
retrieve an e-mail or a header.
3. Select an e-mail or a header.
4. If you selected a header, press
<Options> and select
Retrieve.
20
Turn on
Bluetooth
In Idle mode, press <Menu> and
select Settings → Bluetooth →
Activation → On.
Search for and
pair with a
Bluetooth
device
1. In Idle mode, press <Menu>
and select Settings →
Bluetooth → My devices →
Search new device.
2. Select a device.
3. Enter a Bluetooth PIN or the
other device’s Bluetooth PIN, if
it has one, and press <OK>.
When the owner of the other
device enters the same code,
pairing is complete.
E370.book Page 21 Tuesday, April 18, 2006 5:40 PM
Send data
2. Select an item.
3. Press <Options> and select
Send via → Bluetooth.
Quickly launch menus by number
The dialing screen provides you with shortcuts to
certain menus you can use with an entered number.
With those shortcuts, you can quickly send an SMS
message, set an alarm, perform a conversion/
calculation, or schedule an appointment after entering
a number.
4. Select Search new device.
5. Select a device.
6. If necessary, enter the
Bluetooth PIN and press <OK>.
Receive data
To receive data via Bluetooth, your
phone’s Bluetooth feature must be
active.
If necessary, press <Yes> to
confirm that you are willing to
receive.
Access menus
Step outside the phone
1. Access an application,
Phonebook, File manager, or
Calendar.
1. Enter an appropriate number
for the action you want in Idle
mode.
For example, enter the time
you want as 4-digits to set an
alarm or the date you want as
4-digits to enter your schedule.
2. Press one of the Navigation
keys.
21
E370.book Page 22 Tuesday, April 18, 2006 5:40 PM
Step outside the phone
Access menus
(continued)
You can access the following
applications by default:
•
•
•
•
Up: Alarm p. 40
Down: Converter p. 41
Left: Text message
p. 45
Right: Calendar p. 65
You can change the shortcuts
in Advanced shortcut.
p. 76
22
E370.book Page 23 Tuesday, April 18, 2006 5:40 PM
Enter text
ABC, T9, Number, and Symbol modes
You can enter text for some features such as
messaging, Phonebook, or Calendar, using ABC mode,
T9 mode, Number mode, and Symbol mode.
Using ABC mode
Press the appropriate key until the character you want
appears on the screen.
Key
Characters in order displayed
Upper case
Lower case
Changing the text input mode
•
•
•
Press and hold [ ] to switch between T9 and ABC
modes.
Press [ ] to change case or switch to Number
mode.
Press and hold [ ] to switch to Symbol mode.
(Creating an SMS message with GSM alphabet encoding)
23
E370.book Page 24 Tuesday, April 18, 2006 5:40 PM
Enter text
Other ABC mode operations
•
•
•
•
To enter the same letter twice or to enter a
different letter on the same key, wait for the cursor
to move to the right automatically or press [Right].
Then, enter the next letter.
Press [ ] to insert a space.
Press the Navigation keys to move the cursor.
Press [C] to delete characters one by one. Press
and hold [C] to clear the display.
Using T9 mode
T9 is a predictive text input mode that allows you to
key in any character using single keystrokes.
Entering a word in T9 mode
1. Press [2] to [9] to start entering a word. Press
each key once for each letter.
For example, press [4], [3], [5], [5], and [6] to
enter hello in T9 mode.
T9 predicts the word that you are typing, and it
may change with each key that you press.
24
2. Enter the whole word before editing or deleting
characters.
3. When the word displays correctly, go to step 4.
Otherwise, press [0] to display alternative word
choices for the keys that you have pressed.
For example, of and me use [6] and [3].
4. Press [ ] to insert a space and enter the next
word.
Other T9 mode operations
•
•
•
•
Press [1] to enter periods or apostrophes
automatically.
Press [ ] to insert a space.
Press the Navigation keys to move the cursor.
Press [C] to delete characters one by one. Press
and hold [C] to clear the display.
Adding a new word to the T9 dictionary
This feature may not be available for some languages.
1. Enter the word that you want to add.
E370.book Page 25 Tuesday, April 18, 2006 5:40 PM
2. Press [0] to display alternative words for your key
presses. When there are no more alternative
words, Spell appears on the bottom line.
3. Press <Spell>.
4. Enter the word you want using ABC mode and
press <Add>.
Using Number mode
Number mode enables you to enter numbers.
Press the keys corresponding to the digits you want.
Using Symbol mode
Symbol mode enables you to insert symbols.
Call functions
Advanced calling features
Making a call
1. In Idle mode, enter the area code and phone
number.
• Press [C] to clear the last digit or press and
hold [C] to clear the whole display.
• Press and hold [ ] to insert a pause between
numbers.
2. Press [ ].
3. When you want to end the call, press [
].
Making an international call
To
Press
display more symbols
[Up] or [Down].
select a symbol
the corresponding
number key.
1. In Idle mode, press and hold [0]. The + character
appears.
2. Enter the country code, area code, and phone
number, then press [ ].
clear the entered symbol(s)
[C].
Redialling recent numbers
insert the symbol(s)
<OK>.
1. In Idle mode, press [
recent numbers.
] to display the list of
25
E370.book Page 26 Tuesday, April 18, 2006 5:40 PM
Call functions
2. Scroll to the number you want and press [
].
•
Once you have stored a number in Phonebook, you
can dial the number by selecting it from
Phonebook.p. 31
•
•
You can also use the speed dial feature to assign your
most frequently dialled numbers to specific number
keys.p. 34
You can quickly dial a number from the SIM card using
its location number assigned when stored.
1. In Idle mode, enter the location number for the
phone number you want and press [ ].
2. Find the number you want.
3. Press <Dial> or [ ] to dial the number you want.
When Anykey answer is active, you can press
any key, except for <Reject> and [ ].p. 76
Press <Reject> or [ ] to reject a call.
Press and hold [ / ] to reject a call or mute the
ringer, depending on the Volume key setting.
p. 76
Viewing missed calls
If you have missed calls, the screen displays how
many calls you have missed.
1. Press <View>.
2. Scroll through the missed calls, if necessary.
3. Press [ ] to dial the number you want.
Answering a call
Using the headset
When you receive an incoming call, the phone rings
and displays the incoming call image.
Use the headset to make or answer calls without
holding the phone.
Press <Accept> or [
26
Tips for answering a call
Making a call from Phonebook
] to answer the call.
E370.book Page 27 Tuesday, April 18, 2006 5:40 PM
Connect the headset to the jack on the right side of
the phone. The button on the headset works as
follows:
Press
redial the last call
the button and then press
and hold it again.
answer a call
and hold the button.
end a call
and hold the button.
Options during a call
You can access a number of functions during a call.
Adjusting the volume during a call
Use [ / ] to adjust the earpiece volume during a call.
Press [ ] to increase the volume level and [ ] to
decrease the volume level.
Use the phone as a speakerphone to talk and listen
with the phone a short distance away.
1. During a call, plug the speaker into the phone.
Speaker mode is automatically activated.
2. Press [
] to return to normal phone mode.
Call functions
To
Using the speakerphone feature
Placing a call on hold/Retrieving
Press <Hold> or <Retrieve> to place a call on hold
or retrieve the call.
Making a second call
You can make another call if your network supports
this function.
1. Press <Hold> to put the call on hold.
2. Make the second call in the normal way.
3. Press <Swap> to switch between the calls.
4. Press <Options> and select End held call to end
the call on hold.
5. To end the current call, press [ ].
27
E370.book Page 28 Tuesday, April 18, 2006 5:40 PM
Call functions
Answering a second call
You can answer an incoming call while already on the
phone, if your network supports this function and you
have activated the call waiting feature.p. 81
1. Press [ ] to answer the call. The first call is
automatically put on hold.
2. Press <Swap> to switch between the calls.
3. To end the current call, press [ ].
•
To communicate with answering machines or
computerised telephone systems, Send keys
must be selected.
•
•
Using In-call options
Press <Options> to access the following options
during a call:
• Voice clarity on/Voice clarity off: remove
extraneous noise and increase call quality so that
the person with whom you are speaking can hear
you clearly even if you are in a noisy place.
• Mute/Unmute: switch off the phone's microphone
so that the other person on the phone cannot hear
you, or switch it back on.
28
Mute keys/Send keys: switch the key tones on
or off.
•
•
•
Phonebook: access the contact list.
Send DTMF: send the DTMF (Dual tone multifrequency) tones as a group. The DTMF tones are
the tones used in phones for tone dialling,
sounding when you press the number keys. This
option is helpful for entering a password or an
account number when you call an automated
system, like a banking service.
Message: send a new message or access received
messages.
Join: set up a multi-party call by adding a caller
on hold to a currently active call. You can include
up to 5 people on a multi-party call.
Transfer: transfer the currently active call to a
caller on hold. The two callers can talk to each
other, but you are disconnected from the call.
E370.book Page 29 Tuesday, April 18, 2006 5:40 PM
•
•
•
•
•
End held call: disconnect the call currently on
hold.
Split: have a private conversation with one
multiparty call participant. The other participants
can converse with each other. After the private
conversation, select Join to return both all private
participants to the multi-party call.
Remove: disconnect one multi-party call
participant.
Switch to headset/Switch to phone: switch the
call to a Bluetooth stereo headset or hands-free
car kit or back to the phone.
SIM service: access special services, such as
news, weather forecasts, entertainment, and
location services, provided by your SIM card. This
option is available when you use a SIM card
supporting SIM Application Toolkit menus, and may
be differently displayed depending on your service
provider.
Menu functions
All menu options listed
Call records (Menu 1)
Use this menu to view the calls you have dialled,
received, or missed, and the length of the calls. You
can also check the cost of your calls, if your SIM card
supports this function.
To access this menu, press <Menu> in Idle mode and
select Call records.
Recent contacts (Menu 1.1)
This menu displays the most recent calls dialled,
received, or missed.
Accessing a call record
1. Press [Left] or [Right] to move to another call
type.
2. Press [Up] or [Down] to scroll through the call list.
3. Press [
] to view the details of a call, or press
[ ] to dial a number.
29
E370.book Page 30 Tuesday, April 18, 2006 5:40 PM
Menu functions
Using call record options
Delete all (Menu 1.5)
While viewing call details, press <Options> to access
the following options:
• Save as contacts: save the number in
Phonebook.
• Send message: send an SMS or MMS message to
the selected number.
• Delete: delete the selected call record or all
records.
Use this menu to delete all of the records in each call
type.
1. Press [
] to select the call types to be cleared.
2. Press <Delete>.
3. Press <Yes> to confirm the deletion.
Missed calls (Menu 1.2)
This menu displays the most recent calls you did not
answer.
Dialled calls (Menu 1.3)
This menu displays the most recent calls you have
dialled.
Received calls (Menu 1.4.)
This menu displays the most recent calls you have
received.
30
Call time (Menu 1.6)
This menu displays the time log for calls made and
received. The actual time invoiced by your service
provider will vary.
• Last call time: check the length of your last call.
• Total sent: check the total length of all the calls
you have dialled.
• Total received: check the total length of all the
calls you have received.
• Reset timers: reset the call timers. You need to
enter the phone password.
The password is preset to 00000000. You can
change this password. p. 85
E370.book Page 31 Tuesday, April 18, 2006 5:40 PM
Call costs (Menu 1.7)
Phonebook
This network feature displays the cost of calls. This
menu is available only if supported by your SIM card.
Note that this is not intended to be used for billing
purposes.
• Last call cost: check the cost of your last call.
• Total cost: check the total cost of all of your calls.
If the total cost exceeds the maximum cost set in
Set max cost, you must reset the counter before
you can make another call.
• Max cost: check the maximum cost limit set in
Set max cost.
• Reset counters: reset the cost counters.
• Set max cost: set the maximum cost authorised
for your calls.
• Price/Unit: set the price per unit that is applied
when the cost of your calls is calculated.
You can store phone numbers on your SIM card and in
your phone’s memory. The SIM card and phone’s
memory are physically separate, but they are used as
a single entity called Phonebook.
(Menu 2)
Menu functions
To access this menu, press <Menu> in Idle mode and
select Phonebook.
Contact list (Menu 2.1)
Phonebook (Menu 2)
Use this menu to search for contacts in Phonebook.
Press <Contacts> in Idle mode to quickly access
this menu.
Finding a contact
1. Enter the first few letters of the name that you
want to find.
2. Select the name from the list.
3. Scroll to a number, and press [ ] to dial or press
[
] to edit contact information.
31
E370.book Page 32 Tuesday, April 18, 2006 5:40 PM
Menu functions
32
Using Phonebook options
Adding a contact
While viewing contact details, press <Options> to
access the following options:
• Edit: edit contact information.
• Send message: send an SMS or MMS message to
the selected number, or an e-mail to the selected
address.
• Copy: copy the contact to the phone’s memory,
the SIM card, or FDN list.
• Send via: send the contact via SMS, MMS, e-mail,
or Bluetooth.
• Delete: delete the selected contact.
• Print via Bluetooth: print the contact information
via a Bluetooth-compatible printer.
1. Press <Options> and select Add.
2. Enter your PIN2 and press <OK>.
3. Enter information.
• Name: assign a name.
• Phone number: add a phone number.
• Location: assign a location number.
4. Press <Save> to save the contact.
FDN list (Menu 2.2)
Storing a contact in the phone’s memory
Use this menu to create a list of contacts to be used in
FDN (Fixed Dialling Number) mode, in which the
phone allows outgoing calls only to the specified
phone numbers, if your SIM card supports this
feature. You can activate FDN mode in the FDN mode
menu.p. 85
1. Select Phone.
2. Change the settings or enter information about the
contact.
• First name/Last name: assign a name.
Using contact options
Scroll to a contact and press <Options> to access
options.“Using Phonebook options”
Add new contact (Menu 2.3)
Use this menu to add a new contact to Phonebook.
E370.book Page 33 Tuesday, April 18, 2006 5:40 PM
•
1. Select SIM.
2. Enter information about the contact.
• Name: assign a name.
• Phone number: add a number.
• Location: assign a location number.
To assign a caller ID image, ringtone, or group,
the contact must be saved to the phone’s
memory.
Use this menu to organise your contacts in caller
groups.
Adding members to a caller group
1. Select a group.
2. Press <Add>.
3. Select a contact to be added.
Managing caller groups
Phonebook (Menu 2)
Storing a contact on the SIM card
Group (Menu 2.4)
Menu functions
Mobile/Home/Office/Fax/Other: add a
number in any type.
• Email: assign an e-mail address.
• Graphic ID: assign an image to alert you to a
call from the person.
• Alert: assign a ringtone to alert you to a call
from the person.
• Group: assign the contact to a caller group.
• Notes: add a memo about the person.
3. Press <Save> to save the contact.
While viewing the group list, press <Options> to
access the following options:
• View: display the members of the selected group.
• Add: add a new group.
• Edit: change the properties of the selected group.
• Send message: send an SMS, MMS, or e-mail
message to the group members you want.
• Delete: delete the selected group. Group
members, however, will not be deleted from
Phonebook.
3. Press <Save> to save the contact.
33
E370.book Page 34 Tuesday, April 18, 2006 5:40 PM
Menu functions
Speed dial (Menu 2.5)
My name card (Menu 2.6)
Use this menu to assign a speed dial number (2 to 9)
for 8 of your most frequently dialled numbers.
Use this menu to create a name card and send it to
other people.
Assigning speed dial numbers
Saving your name card
1. Select a key location from 2 to 9. Key 1 is reserved
for your voicemail server.
2. Select a contact from the contact list.
3. Select a number, if the contact has more than one
number.
The procedure for creating your name card is the
same as the one for saving a phone number in the
phone’s memory.p. 32
Managing speed dial entries
From the Speed dial screen, press <Options> to
access the following options:
• Add: assign a number to an unassigned key.
• View: check the name and number assigned to a
key.
• Change: assign a different number to a key.
• Remove: clear the speed dial setting for a key.
Dialling speed dial numbers
In Idle mode, press and hold the appropriate key.
34
Using name card options
After saving your name card, press <Options> to
access the following options:
• Edit: edit the name card.
• Send via: send the name card via SMS, MMS,
e-mail, or Bluetooth.
• Exchange namecard: exchange name cards with
another person via Bluetooth.
• Remove: delete the name card.
• Print via Bluetooth: print your contact
information via a Bluetooth-compatible printer.
E370.book Page 35 Tuesday, April 18, 2006 5:40 PM
Service number (Menu 2.9)
Use this feature to check your phone numbers, or to
assign a name to each of the numbers. Changes made
here do not affect the actual subscriber numbers on
your SIM card.
Use this menu to view the list of Service Dialling
Numbers (SDN) assigned by your service provider,
including emergency numbers and numbers for
directory enquiries. This menu is available if your SIM
card supports SDN.
1. Scroll to the number you want.
2. Press <Dial> or [ ].
Management (Menu 2.8)
Applications
Applications (Menu 3)
Use this menu to manage contacts in Phonebook.
• Default saving: select a default memory location
to save contacts. If you select Ask on saving, the
phone will ask you to select a memory location
each time you save a number.
• Copy all to: copy all of the contacts stored on
your SIM card to your phone’s memory, or vice
versa.
• Sort by contacts: change the sort order of
contacts.
• Delete all: delete all of the contacts from your
phone’s memory, SIM card, or FDN list.
• Memory status: check the number of contacts
you have stored in your phone’s memory and on
the SIM card.
Menu functions
Own number (Menu 2.7)
(Menu 3)
Use this menu to play music files or play Java games.
You can also check the world time and use convenient
features, such as a voice recorder, alarm clock,
calculator, converter, timer, and stopwatch.
To access this menu, press <Menu> in Idle mode and
select Applications.
Music Player (Menu 3.1)
Use this menu to enjoy music. First, you need to save
music files into your phone’s memory.
35
E370.book Page 36 Tuesday, April 18, 2006 5:40 PM
Menu functions
Downloading or receiving music files
Use these methods to save music files to your phone’s
memory:
• Download from the wireless webp. 42
• Download from a computer using the Samsung PC
Studio programSamsung PC Studio User’s
Guide
• Receive via an active Bluetooth connectionp. 84
Playing music files
From the Music player screen, press [
].
During playback, use the following keys:
Keys
Function
Pauses or resumes playback.
The downloaded or received files are stored in the
Music folder.p. 63
Left
Returns to the previous file. Moves
backward in a file when held down.
Creating a play list
Right
Skips to the next file. Moves forward in a
file when held down.
Up
Opens the play list.
1. From the Music player screen, press <Options>
and select Add to list.
2. Select either of the following options:
• Add all: add all of the files in the phone’s
memory to the play list.
• Add a file: add specific files to the play list.
] to select
3. If you selected Add a file, press [
the files you want and press <Add>.
36
4. Press <Back> to go back to the Music player
screen.
Down
/
Stops playback.
Adjusts the volume level.
2
Changes the playback animation.
3
Changes the repeat mode.
6
Turns Shuffle mode on or off.
E370.book Page 37 Tuesday, April 18, 2006 5:40 PM
Using Music player options
From the Music player screen, press [Up] to access the
play list.
Voice recorder (Menu 3.2)
Use this menu to record voice memos. A voice memo
can be up to one hour long.
Applications (Menu 3)
Accessing the play list
Press <Options> to access the following options:
• Play: play the currently selected file.
• Add to list: add files to the play list.
• Change order: move the selected file to the
position you want within the play list.
• Remove: remove the selected file or all files from
the play list.
Menu functions
During playback, press <Options> to access the
following options:
• Pause/Play: pause or begin playback.
• Open play list: access the play list.
• Remove: remove the selected file from the play
list.
• Settings: change the default settings for playing
music files.
Repeat mode: select a repeat mode.
Shuffle: set the Music player to play music in
random order.
Visualization: change the playback animation.
Volume: select a volume level.
• Details: access the file properties.
Recording a voice memo
1. Press [
] to start recording.
2. Speak into the microphone.
Press [
] to pause or resume the recording.
3. Press <Save> or [Down] to end the recording.
The voice memo is saved automatically.
4. Press [
] to review the voice memo, or press
[Up] to record a new memo.
37
E370.book Page 38 Tuesday, April 18, 2006 5:40 PM
Menu functions
Playing a voice memo
•
1. From the Voice recorder screen, press <Options>
and select Go to voice list.
2. Select a voice memo.
•
•
During playback, use the following keys:
Keys
Left
Function
Java world (Menu 3.3)
Pauses or resumes playback.
Use this menu to access and play Java games and to
change the network settings for accessing Java
services.
Moves backward in a memo.
Right
Moves forward in a memo.
Up
Switches to Record mode for a new voice
memo.
Down
Stops playback.
/
Adjusts the volume.
Changing voice recorder settings
You can change the default settings for the voice
recorder. From the Voice recorder screen, press
<Options> and select Settings to access the
following options:
38
Recording time: select a maximum recording
time.
Volume: select a volume level.
Default name: change the default prefix of voice
memos.
Accessing a game
Select a game from the game list and follow the
onscreen instructions. The procedure may differ from
game to game.
Using Java application options
From the application list, press <Options> to access
the following options:
• Start: launch the selected application.
• Delete: delete the selected application.
• Details: access the application properties.
E370.book Page 39 Tuesday, April 18, 2006 5:40 PM
•
•
•
•
World time (Menu 3.4)
Applications (Menu 3)
•
Proxy settings: provide you with the following
options:
When the proxy is set to Enable:
- IP address: enter the HTTP proxy address.
- Port: enter the port number.
When the proxy is set to Disable:
- DNS1: enter the primary DNS address.
- DNS2: enter the secondary DNS address.
Menu functions
•
Permission: set permission settings for services
charging you additional costs, such as network
access and SMS.
Protection: lock the application to protect it from
being deleted, or unlock the application.
Upgrade: upgrade the application to the latest
version, except for embedded games.
Send information via SMS: send the URL
containing the application via SMS, except for
embedded games.
Memory status: access memory information for
applications.
Network settings: set up a connection profile to
be used for applications requiring network access.
The following options are available:
APN: enter the access point name.
Login ID: enter the user ID.
Password: enter the password.
Proxy: select whether or not you use a proxy
server to access network services. Depending on
this setting, options in Proxy settings vary.
Use this menu to find out what time it is in another
part of the world.
Viewing world time
1. From the world map, press [Left] or [Right] to
scroll to the city you want. As the time line moves,
the time and date of the given zone display.
2. Press [
] to save the time zone.
Applying daylight savings time
1. From the world map, press <Options> and select
Set daylight saving time.
39
E370.book Page 40 Tuesday, April 18, 2006 5:40 PM
Menu functions
2. Press [
] to select the time zones you want.
3. Press <Save>.
Alarm (Menu 3.5)
Use this menu to set alarms to sound at specific times.
Setting an alarm
1. Select the type of alarm.
2. Set each alarm option:
• Alarm: activate the alarm.
• Alarm time: enter the time for the alarm to
ring.
• AM/PM: set AM or PM in 12-hour format.
• Alarm day: select the days on which you want
the alarm to sound. If you select Once alarm,
the alarm sounds at the specified time and
then is deactivated.
• Alarm tone: select an alarm tone.
3. Press <Save>.
40
Stopping an alarm
•
•
For a non-wake-up alarm, press any key.
For a wake-up alarm, press <OK> or [
].
Press any key, except <OK> and [
], to stop
the alarm and cause it to sound again after 5
minutes. You can do this a maximum of five times.
Setting the alarm to sound even if the phone
is off
From the Alarm screen, select Auto power → On.
If the phone is off when it is time for the alarm to ring,
the phone is switched on and sounds the alarm.
Deactivating an alarm
1. Select the alarm you want to deactivate.
2. Select Off on the Alarm line.
3. Press <Save>.
Calculator (Menu 3.6)
Use this menu to perform basic arithmetic functions,
such as addition, subtraction, multiplication, and
division.
E370.book Page 41 Tuesday, April 18, 2006 5:40 PM
Use this menu for common conversions, such as
currency and temperature.
Performing a conversion
1. Select a converter.
2. Press [Left] or [Right] to select the original unit
and press [Down].
3. Enter the value to be converted and press [Down].
• Press [ ] to insert a decimal point.
Press [ ] to change the temperature to above
zero (+) or below zero (-).
4. Press [Left] or [Right] to select the unit to which
you want to convert.
The equivalent value for the amount you entered
displays.
Using converter options
Press <Options> to access the following options:
• Clear: clear the current values.
• Reverse: reverse the conversion.
• Currency rates: display the currency rate list.
Applications (Menu 3)
Converter (Menu 3.7)
•
Menu functions
1. Enter the first number.
• Press <.()> to insert a decimal point or
bracket.
• Press [ ] or [ ] to move the cursor.
2. Press one of the Navigation keys to access the
math function you want.
3. Enter the second number.
4. Press [
] to view the result.
5. If necessary, repeat from step 2 to continue the
calculation.
Timer (Menu 3.8)
Use this menu to set a period of time for the phone to
count down. The phone will sound an alarm when the
specified period of time has expired.
Starting the timer
1. Press <Set>.
2. Enter the length of time you want to count down
and press <OK>.
41
E370.book Page 42 Tuesday, April 18, 2006 5:40 PM
Menu functions
3. Press [
] to start counting down.
Stopping the timer
•
•
Press any key when the timer rings.
Press [
] on the Timer screen to stop the timer
before it rings.
Stopwatch (Menu 3.9)
Use this menu to measure elapsed time. The
maximum time is 10 hours.
1. Press [
] to start the stopwatch.
2. Press [
] to check an interval. You can repeat
this step for a total of 4 intervals.
SIM-AT (Menu 3.10)
This menu is available if you use a SIM AT card that
supports SIM Application Toolkit menus and provides
additional services, such as news, weather, sports,
entertainment, and location services. Available
services may vary, depending on your service
provider’s plans. For details, see your SIM card
instructions or contact your service provider.
42
Browser
(Menu 4)
The Wireless Application Protocol (WAP) browser on
your phone allows you to access the wireless web.
From the wireless web, you can access up-to-date
information and a wide variety of media content, such
as games, wallpapers, ringtones, and music files.
To access this menu, press <Menu> in Idle mode and
select Browser.
Home (Menu 4.1)
Use this menu to connect your phone to the network
and load the homepage of the wireless web service
provider. You can also press [
] in Idle mode.
Navigating the web browser
To
Press
scroll through browser items
[Up] or [Down].
select a browser item
<
return to the previous page
<Back> or [C].
return to the homepage
and hold [C].
> or [
].
E370.book Page 43 Tuesday, April 18, 2006 5:40 PM
Using browser options
•
From any web page, press [ ] or select
on the top
of the screen to access the following options:
• Back: go back to the previous page.
• Home: return to the homepage.
• Exit: exit the web browser.
• Reload: reload the current page with updated
information.
• Show URL: display the URL address of the current
web page.
• About...: access version information for the web
browser.
Exiting the browser
Bookmarks (Menu 4.2)
Use this menu to save URL addresses in order to
quickly access web pages.
Adding a bookmark
Browser (Menu 4)
From any web page, press [ ] to access the following
options:
• Goto URL: enter a URL address manually.
• Bookmarks: access the bookmark list.
• Messages: send SMS messages or view the
messages stored on the phone.
Press [ ] to end the network connection and exit the
browser.
Menu functions
Accessing other phone menus
File manager: access the File manager menu.
1. Select an empty location.
2. Enter a name for the bookmark and press [Down].
3. Enter a URL address and press [
].
Accessing a bookmarked page
Selecting a bookmark item launches the web browser
and accesses the associated web page.
43
E370.book Page 44 Tuesday, April 18, 2006 5:40 PM
Menu functions
Using bookmark options
After saving an item, press <Options> to access the
following options:
• Go: access the bookmarked web page.
• Edit: edit the address and name of the bookmark.
• Delete: delete the selected bookmark or all
bookmarks.
Goto URL (Menu 4.3)
Use this menu to manually enter a URL address and
access the associated web page.
Clear cache (Menu 4.4)
Use this menu to clear information stored in the cache.
A cache is a temporary memory that stores recently
accessed web pages.
Profile settings (Menu 4.5)
Use this menu to select a connection profile to be used
for accessing the wireless web. Contact your service
provider for details about your settings options.
44
For each profile, the following options are available:
• Profile name: enter a profile name.
• Home URL: enter the URL address of the page to
be used as your homepage.
• Bearer: select the network bearer type.
• Proxy: activate or deactivate the proxy server.
• GPRS settings: customise the following GPRS
network settings:
When the proxy is set to Enable:
Proxy IP: enter the HTTP proxy server address.
Proxy port: enter the port number.
APN: enter the access point name of the GPRS
network gateway.
Login ID: enter the user ID.
Password: enter the password.
When the proxy is set to Disable:
DNS1: enter the primary address.
DNS2: enter the secondary address.
APN: enter the access point name of the GPRS
network gateway.
E370.book Page 45 Tuesday, April 18, 2006 5:40 PM
•
Current profile (Menu 4.6)
Use this menu to activate one of the proxy servers you
have set up.
Menu functions
Messages (Menu 5)
Use the Messages menu to send and receive text
messages, multimedia messages, and e-mails. You
can also access push messages and broadcast
messages.
Messages (Menu 5)
Login ID: enter the user ID.
Password: enter the password.
GSM settings: customise the following GSM
network settings:
When the proxy is set to Enable:
Proxy IP: enter the HTTP proxy server address.
Proxy port: enter the port number.
Dial number: enter the PPP server phone number.
Login ID: enter the user ID.
Password: enter the password.
Data call type: select a data call type.
When the proxy is set to Disable:
DNS1: enter the primary address.
DNS2: enter the secondary address.
Dial number: enter the PPP server phone number.
Login ID: enter the user ID.
Password: enter the password.
Data call type: select a data call type.
To access this menu, press <Menu> in Idle mode and
select Messages.
Create new message (Menu 5.1)
Use this menu to create and send messages.
Text message (Menu 5.1.1)
Short Message Service (SMS) allows you to send or
receive text messages that may include pictures,
animated images, and melodies.
45
E370.book Page 46 Tuesday, April 18, 2006 5:40 PM
Menu functions
1. Enter your message.
• The maximum number of characters allowed
in a message varies by service provider. If
your message exceeds the maximum number
of characters, the phone will split the
message.
• You can use various options by pressing
<Options>. next section
2. When you have finished, press <Options> and
select Send only or Save and send.
3. Enter a destination number.
To send the message to more than one recipient,
fill in additional destination fields.
4. Press [
] to send the message.
Using options while composing an SMS
message
While composing a message, press <Options> to
access the following options:
• Send only: send the message.
• Save and send: save the copy of the message
and send it.
46
•
•
•
•
•
•
Insert: add a template, Phonebook entry, or
bookmark into text.
Add picture/Add animation/Add melody:
attach a simple image, animated image, or
melody.
Attach: add a name card or calendar data as data
format attachments.
Save to: save the message in the Draft or My
folder box.
Language select: change the language used in
T9 input mode.
Text style: change the text attributes.
Multimedia message (Menu 5.1.2)
Multimedia Message Service (MMS) delivers messages
containing a combination of text, image, video, and
audio, from phone to phone or from phone to e-mail.
1. Select the Subject line.
You can use various options by pressing
<Options> in each field.next section
E370.book Page 47 Tuesday, April 18, 2006 5:40 PM
2. Enter the message subject and press [
].
3. Select the Picture & Video or Sound line and add
an image, a video, or a sound clip.
Messages (Menu 5)
4. Select the Message line.
5. Enter the message text and press [
].
6. When you have finished, press <Options> and
select Send.
7. Enter a phone number or e-mail address.
To send the message to more than one recipient,
fill in additional destination fields.
8. Press [
] to send the message.
While composing a message, press <Options> to
access the following options:
• Add: add the message subject or message text.
• Edit: edit the subject or text of your message.
• Change image/Change video/Change sound:
replace an added item.
• Add image/Add video/Add sound: add an
image, video file, or sound clip.
• Preview: view the message as it will be shown on
the recipient’s phone.
• Send: send the message.
• Save to: save the message to the Draft or My
folder box, or save it as a template.
• Add page: add pages. Move to each page by
pressing [Left] or [Right].
• Delete page: delete an added page.
Menu functions
• The maximum size allowed for a message can
differ, depending on your service provider.
• Depending on the file type or DRM (Digital
Rights Management) system, some files may
not be able to be forwarded.
Using options while composing an MMS
message
47
E370.book Page 48 Tuesday, April 18, 2006 5:40 PM
Menu functions
•
•
•
Edit page: change the duration of page display or
move the page forward or backward among the
other pages.
Attach: attach name cards or calendar data as
data format attachments, or a document file stored
in the Other files folder.
Remove subject/Remove media/Remove
sound/Remove message: remove an added
item.
Email (Menu 5.1.3)
You can create and send e-mails that include text,
audio, and images. To use this feature, you need to
subscribe to an e-mail service and set up your e-mail
account and profile.p. 59, p. 60
1. Select the Subject line.
You can use various options by pressing
<Options> in each field.next section
2. Enter the subject of your e-mail and press [
3. Select the Message line.
4. Enter the e-mail text and press [
].
48
].
5. Select the File attach line and add media files.
Depending on the file type or DRM (Digital Rights
Management) system, some files may not be
able to be forwarded.
6. When you have finished, press <Options> and
select Send.
7. Enter an e-mail address.
To send the e-mail to more than one recipient, fill
in additional destination fields.
8. Press [
] to send the e-mail.
Using options while composing an e-mail
While composing an e-mail, press <Options> to
access the following options:
• Add: add the subject of your e-mail or e-mail text.
• Edit: edit the subject or text.
• Add image/Add videos/Add sounds/Add
music: add media files stored in the phone’s
memory.
• Other files: add document files stored in the
Other files folder.
E370.book Page 49 Tuesday, April 18, 2006 5:40 PM
•
•
•
•
•
My messages (Menu 5.2)
Use this menu to access messages you have received,
sent, or which have failed in sending.
Inbox (Menu 5.2.1)
This folder stores all of the messages you have
received, except for e-mails.
The following icons may appear on the message list;
depending on the message type or status, icons may
vary:
•
SMS / Delivery report
•
MMS
•
MMS notification ( : Being retrieved,
:
Failed to be retrieved)
•
Push message from web servers
Messages (Menu 5)
•
Viewing a message
Menu functions
•
View: play an added item.
Send: send the message.
Save to: save the message in the Draft or My
folder box.
Attach: attach name cards or calendar data as
data format attachments.
Remove subject/Remove message: clear the
subject or text.
Remove: delete the selected attachment or all
attachments.
Remove all attachments: delete all
attachments.
• Depending on the DRM (Digital Rights
Management) system, messages having web
content may not be able to be forwarded.
• A ! icon next to a message means that the
message is of high priority. A grey-coloured
message icon indicates low priority.
Using message options
While viewing a message, press <Options> to access
the following options:
SMS messages
• Reply via: reply to the sender via SMS or MMS.
49
E370.book Page 50 Tuesday, April 18, 2006 5:40 PM
Menu functions
•
•
•
•
•
•
•
•
Forward: forward the message to other people.
Delete: delete the message.
Move to phone/Move to SIM: move the
message between the SIM card and the phone’s
memory.
Add to block list: add the sender’s number to the
Block list to reject the messages from the sender.
Cut address: extract URLs, e-mail addresses, or
phone numbers from the message.
Cut media: save media content from the message
into your phone’s memory.
Print via Bluetooth: print the message via a
Bluetooth-compatible printer.
Protection: protect the message from being
deleted.
MMS messages
• Retrieve: retrieve the MMS message from the
MMS server.
• Reply via SMS: reply to the sender via SMS.
• Reply via MMS to: reply to the sender via MMS.
50
•
•
•
•
•
•
•
Forward: forward the message to other people.
Delete: delete the message.
Add to block list: add the sender’s number to the
Block list to reject the messages from the sender.
Cut address: extract URLs, e-mail addresses, or
phone numbers from the message.
Cut media: save media content from the message
into your phone’s memory.
Protection: protect the message from being
deleted.
Details: access the message properties.
Push messages
• Go to URL: connect to the URL specified in the
message.
• Delete: delete the message.
• Cut address: extract URLs, e-mail addresses, or
phone numbers from the message.
Configuration message
• Install: apply the configuration specified in the
message to your phone.
E370.book Page 51 Tuesday, April 18, 2006 5:40 PM
•
•
•
•
Move to phone/Move to SIM: move the
message between the SIM card and the phone’s
memory.
Sort by: change the sort order of the message list.
Protection: protect the message from being
deleted.
Details: access the message properties.
Delivery report messages
• Delete: delete the message.
•
Draft (Menu 5.2.2)
Outbox (Menu 5.2.3)
From the message list, press <Options> to access
the following options:
• View: open the message.
• Edit: edit the message.
• Send: send the message.
• Delete: delete the selected message or all
messages.
• Move to my folder: move the message to the My
folder box.
This folder stores messages that the phone is
attempting to send or has failed to send.
Messages (Menu 5)
This folder stores messages you have saved to send at
a later time.
Menu functions
•
•
Cut address: extract URLs, e-mail addresses, or
phone numbers from the message.
Delete: delete the message.
Protection: protect the message from being
deleted.
While viewing a message, press <Options> to access
the following options:
• Send again: send the message again.
• Open file: open the attached file.
• Save file: save the attached file in the phone’s
memory.
• Forward: forward the message to other people.
• Delete: delete the message.
51
E370.book Page 52 Tuesday, April 18, 2006 5:40 PM
Menu functions
•
•
•
•
Move to phone/Move to SIM: move the
message between the SIM card and the phone’s
memory.
Print via Bluetooth: print the message via a
Bluetooth-compatible printer.
Protection: protect the message from being
deleted.
Details: access the message properties.
Sentbox (Menu 5.2.4)
This folder stores messages that you have sent.
While viewing a message, press <Options> to access
the following options:
• Open file: open the attached file.
• Save file: save the attached file in the phone’s
memory.
• Forward: forward the message to other people.
• Delete: delete the message.
• Move to phone/Move to SIM: move the
message between the SIM card and the phone’s
memory.
52
•
•
•
Print via Bluetooth: print the message via a
Bluetooth-compatible printer.
Protection: protect the message from being
deleted.
Details: access the message properties.
Email box (Menu 5.2.5)
This folder stores e-mails that you have received.
1. Select an e-mail account.
2. Press <Select> when Check new mail displays.
The phone checks for new e-mails and downloads
received e-mails.
The following icons may appear on the list to show
the e-mail status:
•
: Retrieved from the server
•
: Being retrieved
•
: Failed to be retrieved
A ! icon next to a message means that the
message is of high priority. A grey-coloured
message icon indicates low priority.
3. Select an e-mail or a header.
E370.book Page 53 Tuesday, April 18, 2006 5:40 PM
Using e-mail options
•
•
•
•
•
Add to block list: add the sender’s e-mail
address or subject to the block list to reject e-mails
from the address or containing that subject.
Cut address: extract URLs, e-mail addresses, or
phone numbers from the message.
Cut attachment: save media content from the
message to your phone’s memory.
Print via Bluetooth: print the e-mail via a
Bluetooth-compatible printer.
Protection: protect the e-mail from being deleted.
Details: access the e-mail properties.
My folder (Menu 5.2.6)
Use this menu to save the message you have saved
using the Move to my folder option while reading a
message.
Templates (Menu 5.3)
Use this menu to make and use templates of
frequently used messages.
53
Messages (Menu 5)
While viewing the e-mail or header, press <Options>
to access the following options:
• Retrieve: retrieve one or all of the e-mails from
the e-mail server.
• Open file: open the attached file.
• Save file: save the attached file in the phone’s
memory.
• Reply to: send a reply to the sender or to all of
the other recipients.
• Forward: forward the e-mail to other people.
• Delete: delete the selected e-mail.
•
Menu functions
4. If the e-mail has more than one page, press [ / ]
to scroll through pages one by one.
Press and hold [ / ] to move to the first or last
page.
5. Select an attached file to view or play it.
6. Press [ ] or [ ] to move to the previous or next
e-mail.
E370.book Page 54 Tuesday, April 18, 2006 5:40 PM
Menu functions
Text template (Menu 5.3.1)
You can create SMS templates with the sentences you
use frequently so that you can retrieve and insert
them when composing an SMS message.
Creating a template
1. Select an empty location.
2. Enter a message and press [
].
Using template options
From the template list, press <Options> to access
the following options:
• Edit: edit the selected template.
• Send message: create and send a new message
using the template.
• Delete: delete the selected template.
MMS template (Menu 5.3.2)
You can access embedded MMS templates or ones you
have saved so that you can use them in composing an
MMS message.
54
From the template list, press <Options> to access
the following options:
• View: open the selected template.
• Send message: create and send a new message
using the template.
• Edit: edit the template.
• Add new: add a new template.
• Delete: delete the selected template or all
templates, except for the embedded ones.
Delete all (Menu 5.4)
Use this menu to delete all of the messages in each
message folder at once. You can also select messages
in message type you want to delete.
1. Press [
] to select the message folders or
message types to be cleared.
2. Press <Delete>.
3. Press <Yes> to confirm the deletion.
E370.book Page 55 Tuesday, April 18, 2006 5:40 PM
Settings (Menu 5.5)
Use this menu to set up various options for using the
messaging services.
•
Multimedia message (Menu 5.5.2)
Messages (Menu 5)
You can configure SMS settings.
• Send settings: set up the options for sending
SMS messages:
Reply path: allow recipients to reply to you
through your SMS server.
Delivery report: set the network to inform you
when your messages have been delivered.
Character support: select a character encoding
type. When you select Auto, the phone switches
the encoding type from GSM-alphabet to Unicode if
you enter a Unicode character. Use of Unicode
encoding will reduce the maximum number of
characters in a message to about half. If this menu
is not shown, your phone provides automatic
character encoding by default.
Menu functions
Text message (Menu 5.5.1)
Validity period: set the length of time your
messages are stored in the SMS server.
Message type: set the default message type. The
network can convert the messages into the
selected format.
Service centre: store or change the number of
your SMS server.
Block number: store the phone numbers from
which you want to reject messages.
You can configure MMS settings.
• Send settings: set up the options for sending
MMS messages:
Delivery report: set the network to inform you
when your messages have been delivered.
Address hiding: set your address to be hidden
from the recipient’s phone.
Read reply: send a read-reply request along with
your messages.
Priority: set the priority level of messages.
55
E370.book Page 56 Tuesday, April 18, 2006 5:40 PM
Menu functions
•
56
Expiry Date: set the length of time messages are
stored in the MMS server.
Delivery after: set a time delay before messages
are sent.
Receive settings: set up the options for receiving
MMS messages:
Anonymous reject: reject messages from
unknown senders.
Advert allowed: accept advertisements.
Report allowed: set the network to inform the
sender when a message has been delivered to you.
Home reception: determine if your phone
retrieves new messages automatically when you
are in your home service area.
Roaming reception: determine if your phone
retrieves new messages automatically when you
are roaming in another network.
Reception within home network or abroad has the
following options:
- Automatic: the phone automatically retrieves
messages from the server.
•
- Reject: the phone rejects all messages.
- Manual: the phone displays notifications. Use
the Retrieve option to manually download new
messages.
MMS profiles: set up a connection profile and
select a profile to be used for MMS.
Current profile: select a profile.
Profile settings: set up the following options for
each profile.
- Profile name: assign a name to the MMS profile.
- Server URL: enter the URL address of your MMS
server.
- Proxy: connect to the GPRS network using the
proxy server.
- GPRS settings: customise the settings required
for connecting to the GPRS network.
When the proxy is set to Enable:
IP address: enter the IP address.
Port: enter the port number.
E370.book Page 57 Tuesday, April 18, 2006 5:40 PM
•
Block number: specify phone numbers from
which messages will not be accepted. Numbers
specified here are also included in the SMS
blocking list.
Message class: set up the options creating MMS
messages:
Message class: select the type of message
content you will add or how the message size.
- Text: you can add only text of up to 30 KB.
- Image basic: you can add any type of item,
except for video, of up to 30 KB.
- Image rich: you can add any type of item,
except for video, of up to 100 KB.
- Video basic: you can add any type of item of up
to 100 KB.
- Video rich: you can add any type of items of up
to 300 KB.
Creation mode: select an MMS creation mode.
- Free: you can create a message with any type of
contents and of any size.
Messages (Menu 5)
Depending on your service provider, it may not
be possible to support the maximum limit
300KB. In this case, try again after changing
the setting to 100KB.
•
Menu functions
APN: enter the access point name used for the
address of the GPRS network.
Login ID: enter the user ID.
Password: enter the password.
When the proxy is set to Disable:
DNS1: enter the primary address.
DNS2: enter the secondary address.
APN: enter the access point name used for the
address of the GPRS network.
Login ID: enter the user ID.
Password: enter the password.
- Version: select an available OMA version and
maximum size limit for sending or receiving
messages.
57
E370.book Page 58 Tuesday, April 18, 2006 5:40 PM
Menu functions
- Restricted: you can create a message with the
type of content and size specified in Message
class.
- Warning: you can create a message with any
type of content and of any size, but the phone
will inform you when the content and size have
exceeded the maximum.
Email (Menu 5.5.3)
You can configure e-mail settings.
You cannot change e-mail profile and account
settings while an e-mail is being sent or retrieved.
•
58
Send settings: set up the options for sending emails:
Send copy to self: send a copy of your e-mails to
your e-mail account.
Delivery confirm: set the network to inform you
when your e-mails have been delivered.
Read confirm: send a read-reply request along
with e-mails.
Priority: select the priority level of e-mails.
•
Include signature: attach your name, phone
number, a simple memo, or a tag line to your
e-mails.
Edit name: enter the name in your signature.
Edit telephone number: enter the phone number
in your signature.
Edit note: enter the tag line in your signature.
Receive settings: set up the options for receiving
e-mails.
Check interval: determine how often the phone
checks the server for incoming e-mails. If you
select Not used, use the Check new mail option
to receive new e-mails manually.
Read reply: determine whether or not the phone
sends a read-reply for incoming e-mails. If you
select Announce, the phone asks you to send a
read-reply.
Retrieve option: set whether the phone
downloads e-mail headers only or the complete
e-mail.
E370.book Page 59 Tuesday, April 18, 2006 5:40 PM
- Email address: enter your e-mail address.
- Reply address: enter the e-mail address to
which you want recipients to send reply
messages.
To access the following options, press [
], or
press <Options> and select Next.
- SMTP server: enter the IP address or host name
of the outgoing e-mail server.
- SMTP port: enter the SMTP port number.
- SMTP user ID: enter the SMTP user ID.
- SMTP password: enter the SMTP password.
- Secure connection (SMTP): use a secure
connections for e-mail service.
- Retrieve server type: select the protocol for
the incoming e-mail server. The remaining
options depend on the protocol type setting.
When the protocol type is POP3:
- POP3 server: enter the IP address or host name
of the server that receives your e-mail.
- POP3 port: enter the POP3 port number.
Menu functions
Messages (Menu 5)
•
Delete option: determine whether e-mails are
deleted immediately or the next time you connect
to the server.
Reject if over: determine the maximum size for
incoming e-mails. Your phone will reject e-mails
that exceed the specified size.
Leave a copy of messages on the server: leave
copies of e-mails on the e-mail server after
retrieving.
Email account: set up an e-mail account and
select an account to be used.
Current account: select an account.
Account settings: configure e-mail accounts
using different e-mail servers. Press <Create>, or
press <Options> and select Create:
- In use: activate the current e-mail account.
- Account name: enter a name for the currently
selected account.
To access the following options, press [
], or
press <Options> and select Next.
- User name: enter a user name.
59
E370.book Page 60 Tuesday, April 18, 2006 5:40 PM
Menu functions
- Same ID and password: select to use the same
SMTP user ID and password with incoming
server.
- POP3 user ID: enter the POP3 user ID.
- POP3 password: enter the POP3 password.
- Secure connection (POP3): use a secured
connection for the POP3 protocol.
- APOP login: connect to the server by using the
APOP login scheme.
When the protocol type is IMAP4:
- IMAP4 server: enter the IP address or host
name of the server that receives your e-mail.
- IMAP4 port: enter the IMAP4 port number.
- Same ID and password: select to use the same
SMTP user ID and password with incoming
server.
- IMAP4 user ID: enter the IMAP4 user ID.
- IMAP4 password: enter the IMAP4 password.
- Secure connection (IMAP4): use a secured
connection for the IMAP4 protocol.
60
•
•
- Include attachments: select this option to
receive attachments with e-mails.
- Email retrieval limit: set the number of
headers you will retrieve from the server.
Email profile: configure the network settings
required to send or receive e-mails.
Current profile: select a profile.
Profile settings: configure up to five e-mail
profiles.
- Profile name: enter a profile name.
- APN: enter the access point name.
- Login ID: enter user ID.
- Password: enter the password.
- DNS1: enter the primary DNS address.
- DNS2: enter the secondary DNS address.
Block list: set up an e-mail Block list.
Address list: specify e-mail addresses to reject
e-mails from those addresses.
Subject list: specify subjects to reject e-mails
which contain those subjects.
E370.book Page 61 Tuesday, April 18, 2006 5:40 PM
Push message (Menu 5.5.4)
You can change the settings for receiving broadcast
messages.
• Read: open received messages.
The Temporary box saves network messages until
the phone is switched off.
The Archive box saves network messages
indefinitely. Press <Options> and select Save
when a text notification appears. The message is
saved in the Archive box.
• Receive: select to receive broadcast messages, or
not.
•
Channel: indicate the channels from which you
wish to receive broadcast messages. Please
contact your service provider for further details.
Language: select the preferred languages in
which broadcast messages display.
Memory status (Menu 5.7)
Use this menu to view the maximum memory and
available memory for each message type. You can also
view the amount of memory currently in use in each
folder.
File manager
File manager (Menu 6)
Broadcast messages (Menu 5.6)
•
Menu functions
You can change the settings for receiving push
messages from the wireless web server.
• Receive: set how your phone receives push
messages.
• Service centre: enter the address of the server
from which you want to receive push messages,
when the Receive option is set to SMS-C
specific.
(Menu 6)
The File manager menu allows you to access images,
videos, music files, and sound files stored in the
phone’s memory.
To access this menu, press <Menu> in Idle mode and
select File manager.
According to the DRM (Digital Rights Management)
system, web content may not be able to be
forwarded. The content is indicated by
.
61
E370.book Page 62 Tuesday, April 18, 2006 5:40 PM
Menu functions
Images (Menu 6.1)
•
This menu displays photos you have taken and images
you have downloaded, received in messages, or
imported from your computer.
•
Viewing an image
1. Select an image folder.
2. Select an image.
Viewing a slide show
You can view your photos as a slide show, a sequential
presentation of each photo in the current folder.
1. Select Photos.
2. Press <Options> and select Slide show.
3. Select an interval option. The slide show begins.
4. Press <Cancel> to stop the slide show.
Using image options
While viewing an image, press <Options> to access
the following options:
• List: return to the image list.
62
•
•
•
•
•
•
•
•
•
Send via: send the file via MMS, e-mail, or
Bluetooth.
Set as: set the image as wallpaper for the displays
or as a caller ID image for a Phonebook entry.
Edit: add emoticons, frames, or effects to the
image.
Delete: delete the file.
Rename: change the file name.
Move to/Move to favourite images: move the
file to another folder.
Slide show: view all images as a slide show.
Share for Bluetooth: share the file with other
Bluetooth devices.
Print via Bluetooth: print the image via a
Bluetooth-compatible printer.
Protection: protect the file from being deleted.
Details: access the file properties.
E370.book Page 63 Tuesday, April 18, 2006 5:40 PM
Using video options
This menu displays video clips you have recorded,
downloaded, received in messages, or imported from
your computer.
Function
Left
Moves backward in the file.
Right
Skips forward in a file.
Music (Menu 6.3)
Adjusts the volume.
This menu displays music files you have downloaded,
received in messages, or imported from your
computer.
Video clips recorded on other devices, such as
camcorders, may not play correctly.
Playing a video clip
1. Select a video folder.
2. Select a video clip.
During playback, use the following keys.
Pauses or resumes playback.
/
Down
Stops playback.
File manager (Menu 6)
Keys
While viewing the file list, press <Options> to access
the options.
• Play: play the video clip.
• Send via: send the file via MMS, e-mail, or
Bluetooth.
• Delete: delete the selected file or all files.
• Rename: change the file name.
• Move to/Move to favourite videos: move the
file to another folder.
• Share for Bluetooth: share the file with other
Bluetooth devices.
• Protection: protect the file from being deleted.
• Details: access the file properties.
Menu functions
Videos (Menu 6.2)
63
E370.book Page 64 Tuesday, April 18, 2006 5:40 PM
Menu functions
Playing a music file
Scroll to a file and press [
].p. 36
Using music options
While viewing the file list, press <Options> to access
the following options:
• Play: play the music file.
• Send via: send the file via e-mail or Bluetooth.
• Add play list: add the selected file to the current
play list.
• Set as: set the music file as your call ringtone, a
ringtone for a Phonebook entry, or an alarm tone.
• Delete: delete the selected file or all files.
• Settings: change the default settings for playing
music files.
Repeat mode: select a repeat mode.
Shuffle: set the MP3 player to play music at
random.
Visualization: select a playback animation.
Volume: select a volume level.
64
•
•
•
•
Rename: change the file name.
Share for Bluetooth: share the file with other
Bluetooth devices.
Protection: protect the file from being deleted.
Details: access the file properties.
Sounds (Menu 6.4)
This menu displays voice memos you have recorded,
and sound clips you have downloaded, received in
messages, or imported from your computer.
Playing a sound clip
1. Select a sound folder.
2. Select a sound clip. For a voice memo, see Voice
recorder.p. 38
Using sound options
While viewing the file list, press <Options> to access
the following options:
• Play: play the sound clip.
• Send via: send the file via MMS, e-mail, or
Bluetooth.
E370-2.fm Page 65 Wednesday, April 19, 2006 9:26 AM
•
•
Other files (Menu 6.5)
Files that you receive but which are not supported by
your phone are stored in this folder. These
unsupported file formats include *.doc, *.ppt, *.txt.
While viewing the file list, press <Options> to access
the following options:
• Send via: send the file via MMS, e-mail, or
Bluetooth.
• Delete: delete the selected file or all files.
•
•
•
Rename: change the name of the file.
Share for Bluetooth: share the file with other
Bluetooth devices.
Print via Bluetooth: print the image via a
Bluetooth-compatible printer.
Protection: protect the file from being deleted.
Details: access the file properties.
Memory status (Menu 6.6)
Use this menu to view memory information for media
items in the phone’s memory.
Calendar
Calendar (Menu 7)
•
•
•
•
Menu functions
•
•
•
Set as: set the sound file as your call ringtone, a
ringtone for a Phonebook entry, or an alarm tone.
Delete: delete the selected file or all files.
Rename: change the file name.
Move to favourite sounds/Move to voice list/
Move to downloaded sounds: move the file to
another folder.
Share for Bluetooth: share the file with other
Bluetooth devices.
Protection: protect the file from being deleted.
Details: access the file properties.
(Menu 7)
The Calendar menu enables you to keep track of your
schedule.
To access this menu, press <Menu> in Idle mode and
select Calendar.
65
E370.book Page 66 Tuesday, April 18, 2006 5:40 PM
Menu functions
Selecting a day on the calendar
When you enter the Calendar menu, the calendar in
Month view appears with today’s date indicated by a
blue box.
• Press [Left] or [Right] to move by day.
• Press [Up] or [Down] to move by week.
• Press [ / ] to move by month.
Creating an item
You can store schedule items, anniversaries, and Todo items on the calendar. More than one event per day
can be stored.
Entering a schedule item or miscellaneous
item
1. Select a date on the calendar.
2. Press <Options> and select Create → Schedule
or Miscellaneous.
3. Enter information or change the settings:
• Subject: enter the title of the item.
• Details: enter item details.
66
•
Start date and Start time: enter the starting
date and time for the item.
• AM/PM: select AM or PM in the 12-hour time
format.
• End date and End time: enter the ending date
and time for the item.
• AM/PM: select AM or PM in the 12-hour time
format.
• Location: (for Schedule) enter information
about the item location.
• Alarm: set an alarm for the item.
• before: set how long before the item the alarm
is to alert you.
• Alarm tone: select an alarm tone.
• Repeat: (for Schedule) select to set the item
to recur and select a unit of time to repeat.
• until: (for Schedule) if the item will recur, set
an ending date.
4. Press <Save> to save the item.
E370.book Page 67 Tuesday, April 18, 2006 5:40 PM
1. Select a date on the calendar.
2. Press <Options> and select Create → To do.
3. Enter information or change the settings:
• To do: enter information about the item.
• Start date: enter the starting date.
• Due date: enter the ending date.
• Priority: select a priority level.
4. Press <Save> to save the item.
Calendar (Menu 7)
Entering a To-do item
1. Select a date on the calendar.
2. Press <Options> and select Create →
Anniversary.
3. Enter information or change the settings:
• Occasion: enter information about the
anniversary.
• Date: enter the date.
• Alarm: select to set an alarm for the
anniversary.
• before: set how long before the event the
alarm is to alert you.
• Alarm time: enter the time for the alarm to
sound.
• AM/PM: select AM or PM in the 12-hour time
format.
• Alarm tone: select an alarm tone.
• Repeat every year: select to set the phone to
remind you of the anniversary every year.
4. Press <Save> to save the anniversary.
Menu functions
Entering an anniversary
Consulting the calendar
Once you have scheduled items, the following icons
and the number of items for a specific day appear at
the bottom of the calendar.
•
Schedule item
•
Anniversary
•
To-do item
•
Miscellaneous item
Viewing an item
1. Select a date on the calendar to display the items
for the day.
2. Select an item to view its details.
67
E370.book Page 68 Tuesday, April 18, 2006 5:40 PM
Menu functions
3. Press [Left] or [Right] to access the other items
scheduled for the selected day.
While viewing an item, press <Options> to access
the following options:
• Edit: edit the item.
• Create: add a new item.
• Send via: send the item via SMS, MMS, e-mail, or
Bluetooth.
• View mode: change the view mode of the
calendar.
• Done/Undone: mark the To-do item as done, or
not.
• Delete: delete the item.
• Print via Bluetooth: print item details via a
Bluetooth-compatible printer.
Using calendar options
Press <Options> to access the following options:
• View mode: change the view mode of the
calendar.p. 68
68
•
•
•
•
•
•
Create: add a new item.p. 66
Go to: select today’s date or enter the specific
date you want to access.
Sort by: sort items by the type of items.
Delete: delete the items stored on the calendar by
using various deleting options.
Missed alarm events: view events whose alarms
you have missed.
Memory status: access memory information for
the event items stored on the calendar.
Viewing items in different mode
You can change the calendar display to Day view or
Week view. Press <Options> and select View mode
→ a view mode.
Day view
You can view items for the selected date. Select an
item to view its details.
E370.book Page 69 Tuesday, April 18, 2006 5:40 PM
Week view
Viewing a missed alarm item
When you are unable to acknowledge an alarm for a
schedule item, anniversary, or miscellaneous item, the
phone stores the missed alarm item until you confirm
it.
1. Press <Options> and select Missed alarm
events.
2. Select an item.
3. Press <Confirm> to confirm and delete the item.
(Menu 8)
You can use the camera module embedded in your
phone to take photos and record videos.
To access this menu, press <Menu> in Idle mode and
select Camera, or press and hold [ ].
• Do not take photos of people without their
permission.
• Do not take photos in a place where cameras are
not allowed.
• Do not take photos in a place where you may
interfere with another person’s privacy.
Camera (Menu 8)
You can view items for the selected week. A cell on the
timetable indicates the presence of a scheduled item.
Select a cell in the day you want.
Camera
Menu functions
The following icons may display to indicate the item
status:
•
Alarm set
•
Recurring event
•
Completed to-do
•
To-do priority (Red: high, Blue: normal, and
Grey: low)
Taking a photo
You can take photos in various modes. The camera
produces JPEG photos.
When you take a photo in direct sunlight or in bright
conditions, shadows may appear on the photo.
1. Access the Camera menu to turn on the camera
and switch the display to Capture mode. You can
also press and hold [ ] in Idle mode.
69
E370.book Page 70 Tuesday, April 18, 2006 5:40 PM
Menu functions
2. Make any desired adjustments.
• Press <
> to access camera options.
next section
• Use the keypad to change camera settings or
switch to other modes. p. 71
3. Press [
] or [ ] to take a photo. The photo is
saved in the Photos folder.
4. To
Press
use photo options
<Options>.p. 71
delete the photo
[C] and then <Yes>.
return to Capture mode
<Back> or [
].
Using camera options in Capture mode
In Capture mode, press <
> to access the following
options:
• Record video: switch to Record mode.
• Shooting mode: take a photo in the following
modes:
Single shot: take a photo in normal mode.
70
•
•
•
•
•
•
Multi shot: take a series of action stills. Select the
number of photos the camera will take and the rate
at which the photos are taken.
Effects: change the colour tone or apply a special
effect.
Frames: apply a decorative frame.
Flash: determine the use of the flash.
Timer: set a time delay before the camera takes a
photo.
Go to photos: access the Photos folder.
Settings: change the default settings for taking a
photo.
Size: select an image size.
Quality: select an image quality.
View finder: select a preview screen.
Shutter sound: select the sound that you hear
when you press the shutter release.
Zoom sound: turn on or off the sound that you
hear when zooming in or out.
E370.book Page 71 Tuesday, April 18, 2006 5:40 PM
Key
Function
5
Changes the colour tone or applies a
special effect.
7
Selects a decorative frame.
8
Sets the timer.
Using the keypad in Capture mode
Key
Function
Left/Right
Adjusts the brightness.
Up/Down
Zooms in or out.
Flips the image vertically.
Shows the mirror image.
1
Switches to Record mode.p. 72
2
Changes the image size.
3
Changes the image quality.
4
Changes the camera mode.
Determines the flash use.
0
Goes to the Photos folder.
Changes the preview screen.
Camera (Menu 8)
You can use the keypad to customise your camera
settings in Capture mode.
Menu functions
•
Brightness sound: turn on or off the sound that
you hear when adjusting the image brightness.
Default name: change the default prefix of file
names.
Camera short cuts: view the functions of the
keys you can use in Capture mode.
Using photo options
After saving a photo, press <Options> to access the
following options:
• Take another: return to Capture mode.
• Send via: send the file via MMS, e-mail, or
Bluetooth.
• Set as: set the photo as wallpaper for the displays
or as a caller ID image for a Phonebook entry.
• Multi shot delete all: delete all of the multi-shot
photo.
71
E370.book Page 72 Tuesday, April 18, 2006 5:40 PM
Menu functions
•
•
•
•
•
•
•
Delete: delete the file.
Rename: change the file name.
Go to photos: access the Photos folder. p. 62
Share for Bluetooth: share the file with other
Bluetooth devices.
Print via Bluetooth: print the image via a
Bluetooth-compatible printer.
Protection: protect the file from being deleted.
Details: access the file properties.
Recording a video
You can record a video of what is displayed on the
camera screen and save it.
1. In Capture mode, press [1].
2. Make any desired adjustments.
• Press <
> to access camera options.
next section
• Use the keypad to change camera settings or
switch to other modes.p. 73
] or [ ] to start recording.
3. Press [
72
4. Press [
], < >, or [ ] to stop recording. The
video is saved in the Videos folder.
5. To
Press
play back the video clip
[
].
use video options
<
>.p. 74
delete the video clip
[C] and then <Yes>.
access the Videos folder
[Up].
return to Record mode
<
p. 63
>.
Using camera options in Record mode
In Record mode, press <
> to access the following
options:
• Take a photo: switch to Capture mode.
• Effects: change the colour tone or apply a special
effect.
• Flash: determine the use of the flash.
• Timer: set a time delay before the camera starts
recording.
• Go to videos: access the Videos folder.
E370.book Page 73 Tuesday, April 18, 2006 5:40 PM
•
Using the keypad in Record mode
You can use the keypad to customise your camera
settings in Record mode:
Keys
Menu functions
Function
Left/Right
Adjusts the brightness.
Up/Down
Zooms in or out.
Flips the image vertically.
Shows the mirror image.
1
Switches to Capture mode.p. 69
2
Changes the frame size.
3
Changes the image quality.
4
Changes the video recording mode.
5
Changes the colour tone or applies a
special effect.
7
Mutes or unmutes the audio.
8
Sets the timer.
Camera (Menu 8)
•
Settings: change the following settings for
recording a video:
Recording mode: select a video recording mode.
- Limit of MMS: record a video suitable for MMS
messages.
- Limit of Email: record a video suitable for
e-mails.
- Normal: record a video within the limit of the
currently available memory.
Size: select a file size.
Quality: select an image quality.
Audio rec.: record audio with a video clip.
Zoom sound: turn the sound effect for zooming
on or off.
Brightness sound: turn the sound effect for
brightness adjustment on or off.
Default name: change the default prefix of file
names.
Camcorder short cuts: view the functions of the
keys you can use in Record mode.
73
E370.book Page 74 Tuesday, April 18, 2006 5:40 PM
Menu functions
Keys
Function
Settings (Menu 9)
Determines the flash use.
0
Goes to the Videos folder.
The Settings menu provides you with various setting
options to customise the phone to your preferences
and needs. You can also reset the settings to their
default status.
Using video options
After saving a video clip, press <
> to access the
following options:
• Record another: return to Record mode.
• Send via: send the file via MMS, e-mail, or
Bluetooth.
• Delete: delete the file.
• Rename: change the file name.
• Go to videos: access the Videos folder. p. 63
• Share for Bluetooth: share the file with other
Bluetooth devices.
• Protection: protect the file from being deleted.
• Details: access the file properties.
74
To access this menu, press <Menu> in Idle mode and
select Settings.
Time & Date (Menu 9.1)
Use this menu to change the time and date displayed
on your phone. Before setting the time and date,
specify your time zone in Home zone.
• Time: enter the current time.
• Home zone: set your local time zone and find out
what time it is in another part of the world.
To apply daylight savings time to time zones,
select Set daylight saving time.
•
•
•
AM/PM: select AM or PM in 12-hour time format.
Time format: select a time format.
Set date: enter the current date.
E370.book Page 75 Tuesday, April 18, 2006 5:40 PM
•
•
Date format: select a date format.
Week start day: set which day of the week the
calendar starts with.
Many different features of your phone’s system can be
customised to suit your preferences.
Language (Menu 9.2.1)
Greeting message (Menu 9.2.2)
Use this menu to enter the greeting that is displayed
briefly when the phone is switched on.
Slide settings (Menu 9.2.3)
Use this menu to set how the phone reacts when you
open it for an incoming call, and when you close it
while using a function.
• Up: set whether or not to answer a call by opening
the phone.
When you set Down to Continue operation,
the keypad lock works just in Idle mode.
Short cut (Menu 9.2.4)
You can use the Navigation keys as shortcuts to access
specific menus directly from Idle mode. Use this menu
to assign a shortcut to a key.
Assigning a shortcut menu
1. Select a key to be used as a shortcut key.
2. Select the menu to be assigned to the key.
Settings (Menu 9)
Use this menu to select one of several languages for
the display text.
Down: set whether or not the phone maintains
the menu you are using when you close the phone.
Menu functions
Phone settings (Menu 9.2)
•
Using shortcut options
Press <Options> to access the following options:
• Change: assign or change a shortcut menu.
• Remove: deactivate the shortcut assignment to
the selected key.
• Remove all: deactivate all shortcut assignments.
75
E370.book Page 76 Tuesday, April 18, 2006 5:40 PM
Menu functions
Advanced shortcut (Menu 9.2.5)
Volume key (Menu 9.2.6)
Use this menu to activate the Advanced shortcut
feature. You can quickly access the text message,
alarm, calculator, calendar, and converter applications
from the dialling screen.
Use this menu to change the volume key settings.
• Volume key function: set whether the phone
mutes the call ringer or rejects a call if you press
and hold [ / ] when a call comes in. You can also
set whether the phone sends an SMS message to
the caller when a call is rejected.
• Text message: enter a message to be sent to the
caller when a call is rejected.
Activating the Advanced shortcut feature
1. From the Advanced screen, select On.
2. Press <Save>.
Changing an Advanced shortcut key
1. Select a key to be changed as a shortcut key.
2. Select the menu that will be assigned to the key.
Using Advanced shortcut options
Press <Options> to access the following options:
• Change: assign or change a shortcut menu.
• Remove: deactivate the shortcut assignment to
the selected key.
• Remove all: deactivate all shortcut assignments.
76
Extra settings (Menu 9.2.7)
You can turn the automatic redialling or answering
feature on or off and activate the voice clarity feature.
• Auto redial: set the phone to make up to ten
attempts to redial a phone number after an
unsuccessful call.
• Anykey answer: answer an incoming call by
pressing any key, except for <Reject> and [ ].
When this option is not selected, you must press
<Accept> or [ ] to answer a call.
E370.book Page 77 Tuesday, April 18, 2006 5:40 PM
•
Dialling display (Menu 9.3.3)
Use this menu to select a font colour and size for the
numbers entered and the background colour of the
display while dialling.
Calendar (Menu 9.3.4)
Use this menu to change settings for the display and
light.
Use this menu to display the current calendar on the
idle screen.
Wallpaper (Menu 9.3.1)
Skin (Menu 9.3.5)
You can change the background image that is
displayed in Idle mode.
Use this menu to select a skin colour for Menu mode.
Text display (Menu 9.3.2)
You can adjust the brightness of the display for
varying lighting conditions.
You can change the display settings for the text
displayed on the idle screen.
• Text position: select a text position. If you don’t
want to display text in Idle mode, select Off.
• Text style: select a font style.
• Text colour: select a font colour.
Settings (Menu 9)
Display settings (Menu 9.3)
Menu functions
Voice clarity: increase the microphone’s
sensitivity to allow the other person on the phone
to hear your voice clearly, even though you may be
whispering.
LCD brightness (Menu 9.3.6)
Show caller information (Menu 9.3.7)
Use this menu to have a caller’s phone number, or
name if saved in Phonebook, shown on the main
display after you have missed a call.
77
E370.book Page 78 Tuesday, April 18, 2006 5:40 PM
Menu functions
Sound settings (Menu 9.4)
Keypad tone (Menu 9.4.2)
Use this menu to customise various sound settings.
Use this menu to select the tone that the phone
sounds when you press a key.
Incoming call (Menu 9.4.1)
Use this menu to select a volume and alert type for
incoming calls.
• Alert type: specify how you are to be informed of
incoming calls.
Melody: the phone rings using the selected
ringtone.
Vibration: the phone vibrates but not rings.
Vibration then melody: the phone vibrates three
times and then starts ringing.
Melody then vibration: the phone rings and then
vibrates.
• Ring tone: select a ringtone for the call ringer.
• Volume: select a ringer volume.
78
You can adjust the keypad tone volume using
[ / ] in Idle mode.
Message tone (Menu 9.4.3)
Use this menu to change the sound settings for
incoming SMS messages, MMS messages, e-mails
individually.
• Tone: select one of several message tones.
• Alert type: specify how you are to be informed
when a message comes in.
• Repetition: specify how often the phone informs
you of a new message.
Power on/off (Menu 9.4.4)
Use this menu to select the melody that the phone
sounds when it is switched on or off.
E370.book Page 79 Tuesday, April 18, 2006 5:40 PM
Slide tone (Menu 9.4.5)
Light settings (Menu 9.5)
Use this menu to select the tone that the phone
sounds when you open or close the phone.
Use this menu to change the settings for backlight.
Use this menu to set how the phone acts to alert you
to a specific event while in Quiet mode.
Extra tones (Menu 9.4.7)
You can select the length of time the backlight or
display stays on.
• On: select the length of time the backlight stays
on.
• Dim: select the length of time the display stays on
in Dim mode after the backlight turns off. After a
specified time, the display turns off.
Settings (Menu 9)
Use this menu to customise additional tones for the
phone.
• Minute minder: set the phone to beep every
minute during an outgoing call to keep you
informed of the length of your call.
• Connection tone: set the phone to beep when an
outgoing call connects to the system.
• Alerts on call: set the phone to beep when you
receive a new message or when the time for an
alarm comes during a call.
• Indicative tones: set the phone to beep when a
pop-up window displays.
Backlight (Menu 9.5.1)
Menu functions
Quiet mode (Menu 9.4.6)
Keypad light (Menu 9.5.2)
You can select the keypad backlight setting.
• Use at any time: flash the backlight when you
press any key.
• Use at night time: flash the backlight only
between 05:00 PM and 09:00 AM.
• Use at custom time: flash the backlight during
the period time you have specified.
79
E370.book Page 80 Tuesday, April 18, 2006 5:40 PM
Menu functions
Network services (Menu 9.6)
Use this menu to access network services. Please
contact your service provider to check their availability
and subscribe to them, if you wish.
Call diverting (Menu 9.6.1)
This network service reroutes incoming calls to a
phone number that you specify.
1. Select a call diverting option:
• Divert always: divert all calls.
• Busy: divert calls when you are on another
call.
• No reply: divert calls when you do not answer
the phone.
• Unreachable: divert calls when you are not in
a service area or when your phone is switched
off.
• Cancel all: cancel all call diverting options.
2. Select the type of calls to be diverted.
3. Select Activate. To deactivate call diverting, select
Deactivate.
80
4. Move to the Divert to line.
5. Enter the number to which calls are to be diverted.
6. If you selected No reply, move to the Sec line and
select the length of time the network delays before
diverting a call.
7. Press <Select>.
Call barring (Menu 9.6.2)
This network service allows you to restrict your calls.
1. Select a call barring option:
• All outgoing: prohibit outgoing calls.
• International: prohibit international calls.
• International except home: only allow calls
to numbers within the current country when
you are abroad, and to your home country.
• All incoming: prohibit incoming calls.
• Incoming while abroad: prohibit incoming
calls when you use your phone outside of your
home service area.
• Cancel all: cancel all call barring settings,
allowing calls to be sent and received normally.
E370.book Page 81 Tuesday, April 18, 2006 5:40 PM
•
You can select a network other than your home
network only if there is a valid roaming agreement
between the two.
Caller ID (Menu 9.6.5)
This network service allows you to prevent your phone
number from being displayed on the phone of the
person being called. If you select Default, the phone
will use the default setting provided by the network.
Network selection (Menu 9.6.4)
This network service allows you to manually select the
network to be used while roaming outside of your
home area, or to let the network be chosen
automatically.
Settings (Menu 9)
Some networks may not allow you to change this
setting.
Call waiting (Menu 9.6.3)
This network service informs you when someone is
trying to reach you while you are on another call.
1. Select the type of calls to which call waiting option
will apply.
2. Select Activate and press <Select>.
To deactivate call waiting, select Deactivate.
Menu functions
Change barring password: change the call
barring password obtained from your service
provider.
2. Select the type of calls to be barred.
3. Select Activate. To deactivate call barring, select
Deactivate.
4. Enter the call barring password supplied by your
service provider and press <Select>.
Voice mail server (Menu 9.6.6)
Use this menu to store the number of the voicemail
server and access your voicemails.
You must enter the voice server number before you
can access your voicemails. Your service provider
can give the voice server number.
•
•
Connect to voice mail: connect to the voicemail
server to listen to your messages.
Voice server number: enter the voicemail server
name and number.
81
E370.book Page 82 Tuesday, April 18, 2006 5:40 PM
Menu functions
Band selection (Menu 9.6.7)
For the phone to make and receive phone calls, it
must register with an available network. Your phone
can handle any of the following types of networks:
GSM 1900, Combined GSM 900/1800, and Tri band
(GSM 900/1800/1900).
The country where you purchased your phone
determines the default band that it uses. When you
travel abroad, you may need to change to an
appropriate band.
Bluetooth (Menu 9.7)
Using the Bluetooth feature, you can connect the
phone wirelessly to other Bluetooth devices and
exchange data with them, talk hands-free, or control
the phone remotely.
Bluetooth technology allows free wireless connections
between all Bluetooth-compliant devices within a
range of 10 meters. Since the devices communicate
using radio waves, they do not need to be in line of
sight to each other.
82
• If there are obstacles between the devices, the
operating distance may be reduced.
• It is recommended that you don’t use the
Bluetooth feature while using multimedia features,
such as voice recorder, camera, and Music player,
or vice versa, for better performance.
• Some devices may not be compatible with your
phone.
Setting up the Bluetooth feature
The Bluetooth menu provides the following options:
• Activation: activate or deactivate the Bluetooth
feature.
• My devices: search for connectable Bluetooth
devices.
• My phone’s visibility: allow other Bluetooth
devices to search for your phone.
• My phone’s name: assign a Bluetooth device
name to your phone, which is then displayed on
other devices.
• Secure mode: determine if the phone asks for
your confirmation when other devices access your
data.
E370.book Page 83 Tuesday, April 18, 2006 5:40 PM
•
Bluetooth services: display available Bluetooth
services.
1. From the Bluetooth menu, select My devices.
2. Select Search new device.
After searching, a list of devices to which you can
connect displays. The following icons indicate the
type of device:
Headset
•
Printer
•
Computer
•
PDA
•
Mobile phone
•
Unknown device
The colour of the icon indicates the status of the
the device:
• Grey for unpaired devices
• Blue for paired devices
• Red for devices that are currently connected to
your phone
3. Select a device.
Some devices, especially headsets or hands-free car
kits, may have a fixed Bluetooth PIN, such as 0000.
If the other device has a code, you must enter it.
Using device options
Settings (Menu 9)
•
Menu functions
Searching for and pairing with a Bluetooth
device
4. Enter a Bluetooth PIN and press <OK>. This code
is used just once and you don’t need to memorise
it.
When the owner of the other device enters the
same code, pairing is complete.
From the device list, press <Options> to access the
following options:
• Connect: connect to a headset or hands-free car
kit.
• Disconnect: end the connection with the
connected device.
• Browse files: search for data from the device and
import data directly to your phone.
• Service list: access the Bluetooth service list of
the device.
• Rename: rename the paired device.
83
E370.book Page 84 Tuesday, April 18, 2006 5:40 PM
Menu functions
•
•
Authorize device/Unauthorize device:
determine whether or not the phone asks you to
permit connection when other devices try to
connect to your phone.
Delete: remove the selected device or all devices
from the list.
Sending data via Bluetooth
1. Activate the Bluetooth feature.
2. Select the application in which the item you want
to send is stored.
3. Select the item you want
4. Press <Options> and select Send via →
Bluetooth.
5. Select Search new device.
The phone searches for devices within range and
displays a list of available devices.
6. Select a device.
7. If necessary, enter the Bluetooth PIN needed for
pairing and press <OK>.
84
Receiving data via Bluetooth
To receive data via Bluetooth, your phone’s Bluetooth
feature must be active.
1. If an unauthorised Bluetooth device sends data to
your phone, press <Yes> to allow the device to
access your phone.
2. Press <Yes> to receive data.
Security (Menu 9.8)
Use this menu to protect the phone against
unauthorised use by managing the several access
codes of your phone and SIM card.
If you enter an incorrect PIN/PIN2 three times in
succession, the SIM card is blocked. To unblock it,
you need to enter your PUK/PUK2 (Personal
Unblocking Key). The codes are supplied by your
network operator.
PIN check (Menu 9.8.1)
The 4- to 8-digit PIN (Personal Identification Number)
protects your SIM card against unauthorised use.
When this feature is enabled, the phone requires your
PIN each time it is switched on.
E370.book Page 85 Tuesday, April 18, 2006 5:40 PM
SIM lock (Menu 9.8.6)
Use this menu to change your PIN. The PIN check
feature must be enabled to use this feature.
This menu allows your phone to work only with the
current SIM card by assigning a SIM lock code. You
must enter the SIM lock code to use a different SIM
card.
Phone lock (Menu 9.8.3)
Use this menu to lock the phone from unauthorised
use. When this feature is enabled, you must enter a 4to 8-digit phone password each time the phone is
switched on.
Change password (Menu 9.8.4)
Use this menu to change your phone password.
Privacy (Menu 9.8.5)
Use this menu to lock access to messages, media files,
Phonebook, or call records, except for call functions.
When a privacy option is enabled, you must enter the
phone password to access the locked items or
functions.
FDN mode (Menu 9.8.7)
If supported by your SIM card, Fixed Dialling Number
(FDN) mode restricts your outgoing calls to a limited
set of phone numbers. When this feature is enabled,
you can make calls only to phone numbers stored on
the SIM card.
Settings (Menu 9)
The password is preset to 00000000. To change the
password, use the Change password menu.
Menu functions
Change PIN (Menu 9.8.2)
Change PIN2 (Menu 9.8.8)
If supported by your SIM card, use this menu to
change your current PIN2.
Memory status (Menu 9.9)
Use this menu to check the amount of memory for
messages, media items, calendar items, contacts, and
Java applications. You can also check the shared
memory for MMS, Email, and File manager.
85
E370.book Page 86 Tuesday, April 18, 2006 5:40 PM
Reset settings (Menu 9.10)
Use this menu to reset the phone settings, display
settings, and sound settings individually.
1. Press [
] to select the setting categories to be
reset
2. Press <Reset>.
3. Press <Yes> to confirm the reset.
4. Enter the phone password and press <OK>.
The password is preset to 00000000. You can
change this password. p. 85
VOD settings (Menu 9.11)
Use this menu to select a connection profile to be used
for accessing a video streaming sever. This menu may
not be shown depending on your service provider.
86
Solve problems
Help and personal needs
To save the time and expense of an unnecessary service
call, perform the simple checks in this section before
contacting a service professional.
When you switch on your phone, the
following messages may appear:
“Insert SIM card”
• Be sure that the SIM card is correctly installed.
“Phone lock”
• The automatic locking function has been enabled.
You must enter the phone’s password before you
can use the phone.
“Enter PIN”
• You are using your phone for the first time. You
must enter the PIN supplied with the SIM card.
• The PIN check feature is enabled. Every time the
phone is switched on, the PIN has to be entered.
To disable this feature, use the PIN check menu.
E370.book Page 87 Tuesday, April 18, 2006 5:40 PM
•
“No Service,” “Network Failure,” or “Not
Done” displays
Your correspondent cannot hear you speaking
•
•
The network connection has been lost. You may be
in a weak signal area. Move and try again.
You are trying to access an option for which you
have no subscription with your service provider.
Contact the service provider for further details.
You have entered a number but it was not
dialled
•
•
•
Be sure that you have pressed [ ].
Be sure that you have accessed the right cellular
network.
Be sure that you have not set an outgoing call
barring option.
Your correspondent cannot reach you
•
Be sure that your phone is switched on. ([
pressed for more than one second.)
•
•
•
Be sure that you have switched on the
microphone.
Be sure that you are holding the phone close
enough to your mouth. The microphone is located
at the bottom of the phone.
The phone starts beeping and “Battery low”
flashes on the display
•
Your battery is insufficiently charged. Recharge the
battery.
The audio quality of the call is poor
•
•
]
Be sure that you are accessing the correct cellular
network.
Be sure that you have not set an incoming call
barring option.
Check the signal strength indicator on the display
(
). The number of bars indicates the signal
strength from strong (
) to weak ( ).
Try moving the phone slightly or moving closer to a
window if you are in a building.
87
Solve problems
“Enter PUK”
• The PIN has been entered incorrectly three times
in succession, and the SIM card is now blocked.
Enter the PUK supplied by your service provider.
E370.book Page 88 Tuesday, April 18, 2006 5:40 PM
No number is dialled when you re-call a
Phonebook entry
•
•
Use the Contact list feature to ensure the number
has been stored correctly.
Re-store the number, if necessary.
The battery doesn’t charge properly or the
phone sometimes turns itself off
•
Wipe the charging contacts both on the phone and
on the battery with a clean soft cloth.
If the above guidelines do not help you to
solve the problem, take note of:
•
•
•
The model and serial numbers of your phone
Your warranty details
A clear description of the problem
Then contact your local dealer or Samsung after-sales
service.
Health and safety information
SAR certification information
This phone meets European Union (EU) requirements
concerning exposure to radio waves.
Your mobile phone is a radio transmitter and receiver. It is
designed and manufactured to not exceed the limits for
exposure to radio-frequency (RF) energy, as
recommended by the EU Council. These limits are part of
comprehensive guidelines and establish permitted levels
of RF energy for the general population. The guidelines
were developed by independent scientific organisations
through the periodic and thorough evaluation of scientific
studies. The limits include a substantial safety margin
designed to ensure the safety of all persons, regardless of
age and health.
The exposure standard for mobile phones employs a unit
of measurement known as Specific Absorption Rate (SAR).
The SAR limit recommended by the EU Council is 2.0
W/kg.*
The highest SAR value for this model phone was 0.486
W/kg.
88
E370.book Page 89 Tuesday, April 18, 2006 5:40 PM
Before a new model phone is available for sale to the
public, compliance with the European R&TTE Directive
must be shown. This directive includes as one of its
essential requirements the protection of the health and
safety of the user and any other person.
Precautions when using batteries
•
•
•
•
•
•
* The SAR limit for mobile phones used by the public is 2.0
watts/kilogram (W/kg) averaged over ten grams of body tissue. The limit incorporates a substantial margin of safety to
give additional protection for the public and to account for any
variations in measurements. The SAR values may vary,
depending on national reporting requirements and the network
band.
Never use a charger or battery that is damaged in any
way.
Use the battery only for its intended purpose.
If you use the phone near the network’s base station,
it uses less power. Talk and standby time are greatly
affected by the signal strength on the cellular network
and the parameters set by the network operator.
Battery charging time depends on the remaining
battery charge, the type of battery, and the charger
used. The battery can be charged and discharged
hundreds of times, but it will gradually wear out. When
the operation time is noticeably shorter than normal, it
is time to buy a new battery.
If left unused, a fully charged battery will discharge
itself over time.
Use only Samsung-approved batteries, and recharge
your battery only with Samsung-approved chargers.
Disconnect the charger from the power source when it
is not in use. Do not leave the battery connected to a
charger for more than a week, since overcharging may
shorten its life.
Health and safety information
SAR tests are conducted using standard operating
positions with the phone transmitting at its highest
certified power level in all tested frequency bands.
Although the SAR is determined at the highest certified
power level, the actual SAR level of the phone while
operating can be well below the maximum value. This is
because the phone is designed to operate at multiple
power levels so as to use only the power required to reach
the network. In general, the closer you are to a base
station, the lower the power output of the phone.
89
E370.book Page 90 Tuesday, April 18, 2006 5:40 PM
Health and safety information
•
•
•
•
90
Extreme temperatures will affect the charging capacity
of your battery: it may require cooling or warming
first.
Do not leave the battery in hot or cold places because
the capacity and lifetime of the battery will be
reduced. Try to keep the battery at room temperature.
A phone with a hot or cold battery may not work
temporarily, even when the battery is fully charged.
Li-ion batteries are particularly affected by
temperatures below 0°C (32°F).
Do not short-circuit the battery. Accidental shortcircuiting can occur when a metallic object like a coin,
clip or pen causes a direct connection between the +
and – terminals of the battery (metal strips on the
battery). For example, do not carry a spare battery in
a pocket or bag where the battery may contact metal
objects. Short-circuiting the terminals may damage
the battery or the object causing the short-circuiting.
Dispose of used batteries in accordance with local
regulations. Always recycle. Do not dispose of
batteries in a fire.
Road safety
Your wireless phone gives you the powerful ability to
communicate by voice, almost anywhere, anytime. But an
important responsibility accompanies the benefits of
wireless phones, one that every user must uphold.
When you are driving a car, driving is your first
responsibility. When using your wireless phone while
driving, follow local regulations in the country or region
you are in.
Operating environment
Remember to follow any special regulations in force in the
area you are in, and always switch off your phone
whenever it is forbidden to use it, or when it may cause
interference or danger.
When connecting the phone or any accessory to another
device, read its user’s guide for detailed safety
instructions. Do not connect incompatible products.
E370.book Page 91 Tuesday, April 18, 2006 5:40 PM
Electronic devices
Most modern electronic equipment is shielded from radio
frequency (RF) signals. However, certain electronic
equipment may not be shielded against the RF signals
from your wireless phone. Consult the manufacturer to
discuss alternatives.
Pacemakers
Pacemaker manufacturers recommend that a minimum
distance of 15 cm (6 inches) be maintained between a
wireless phone and a pacemaker to avoid potential
interference with the pacemaker. These recommendations
are consistent with the independent research and
recommendations of Wireless Technology Research. If you
have any reason to suspect that interference is taking
place, switch off your phone immediately.
Hearing aids
Some digital wireless phones may interfere with some
hearing aids. In the event of such interference, you may
wish to consult your hearing aid manufacturer to discuss
alternatives.
Health and safety information
As with other mobile radio transmitting equipment, users
are advised that for the satisfactory operation of the
equipment and for the safety of personnel, it is
recommended that the equipment should only be used in
the normal operating position (held to your ear with the
antenna pointing over your shoulder).
Other medical devices
If you use any other personal medical devices, consult the
manufacturer of your device to determine if it is
adequately shielded from external RF energy.
Your physician may be able to assist you in obtaining this
information.
Switch off your phone in health care facilities when
regulations posted in these areas instruct you to do so.
Vehicles
RF signals may affect improperly installed or inadequately
shielded electronic systems in motor vehicles. Check with
the manufacturer or its representative regarding your
vehicle.
You should also consult the manufacturer of any
equipment that has been added to your vehicle.
91
E370.book Page 92 Tuesday, April 18, 2006 5:40 PM
Health and safety information
Posted facilities
Emergency calls
Switch off your phone in any facility where posted notices
require you to do so.
This phone, like any wireless phone, operates using radio
signals, wireless, and landline networks as well as userprogrammed functions, which cannot guarantee
connection in all conditions. Therefore, you should never
rely solely on any wireless phone for essential
communications like medical emergencies.
Potentially explosive environments
Switch off your phone when in any area with a potentially
explosive atmosphere, and obey all signs and instructions.
Sparks in such areas could cause an explosion or fire
resulting in bodily injury or even death.
Users are advised to switch off the phone while at a
refuelling point (service station). Users are reminded of
the need to observe restrictions on the use of radio
equipment in fuel depots (fuel storage and distribution
areas), chemical plants, or where blasting operations are
in progress.
Areas with a potentially explosive atmosphere are often
but not always clearly marked. They include the areas
below decks on boats, chemical transfer or storage
facilities, vehicles using liquefied petroleum gas, such as
propane or butane, areas where the air contains chemicals
or particles, such as grain, dust or metal powders, and any
other area where you would normally be advised to turn
off your vehicle engine.
92
To make or receive calls, the phone must be switched on
and in a service area with adequate signal strength.
Emergency calls may not be possible on all wireless phone
networks or when certain network services and/or phone
features are in use. Check with local service providers.
To make an emergency call:
1. Switch on the phone.
2. Key in the emergency number for your present
location. Emergency numbers vary by location.
3. Press [ ].
Certain features like Call Barring may need to be
deactivated before you can make an emergency call.
Consult this document and your local cellular service
provider.
E370.book Page 93 Tuesday, April 18, 2006 5:40 PM
Care and maintenance
•
Your phone is a product of superior design and
craftsmanship and should be treated with care. The
suggestions below will help you fulfill any warranty
obligations and allow you to enjoy this product for many
years.
•
•
•
•
•
Only qualified personnel should service the phone or
install the phone in a vehicle. Faulty installation or
service may be dangerous and may invalidate any
warranty applicable to the device.
Check regularly that all wireless phone equipment in
your vehicle is mounted and operating properly.
Do not store or carry flammable liquids, gases, or
explosive materials in the same compartment as the
phone, its parts, or accessories.
For vehicles equipped with an air bag, remember that
an air bag inflates with great force. Do not place
objects, including installed or portable wireless
equipment, in the area over the air bag or in the air
bag deployment area. Improperly installed wireless
equipment could result in serious injury if the air bag
inflates.
Switch off your phone before boarding an aircraft. It is
dangerous and illegal to use wireless phones in an
aircraft because they can interfere with the operation
of the aircraft.
Failure to observe these instructions may lead to the
suspension or denial of telephone services to the
offender, or legal action, or both.
•
•
•
•
•
Health and safety information
Other important safety information
Keep your phone and all its parts and accessories out
of the reach of small children and pets. They may
accidentally damage these things or choke on small
parts.
Keep the phone dry. Precipitation, humidity, and liquids
contain minerals that corrode electronic circuits.
Do not use the phone with a wet hand. Doing so may
cause an electric shock to you or damage to the phone.
Do not use or store the phone in dusty, dirty areas, as
its moving parts may be damaged.
Do not store the phone in hot areas. High
temperatures can shorten the life of electronic
devices, damage batteries, and warp or melt certain
plastics.
93
E370.book Page 94 Tuesday, April 18, 2006 5:40 PM
Health and safety information
•
•
•
•
•
•
•
94
Do not store the phone in cold areas. When the phone
warms up to its normal operating temperature,
moisture can form inside the phone, which may
damage the phone’s electronic circuit boards.
Do not drop, knock, or shake the phone. Rough
handling can break internal circuit boards.
Do not use harsh chemicals, cleaning solvents, or
strong detergents to clean the phone. Wipe it with a
soft cloth slightly dampened in a mild soap-and-water
solution.
Do not paint the phone. Paint can clog the device’s
moving parts and prevent proper operation.
Do not put the phone in or on heating devices, such as
a microwave oven, stove, or radiator. The phone may
explode when overheated.
When the phone or battery gets wet, the label
indicating water damage inside the phone changes
colour. In this case, phone repairs are no longer
guaranteed by the manufacturer's warranty, even if
the warranty for your phone has not expired.
If your phone has a flash or light, do not use it too
close to the eyes of people or animals. This may cause
damage to their eyes.
•
•
Use only the supplied or an approved replacement
antenna. Unauthorised antennas or modified
accessories may damage the phone and violate
regulations governing radio devices.
If the phone, battery, charger, or any accessory is not
working properly, take it to your nearest qualified
service facility. The personnel there will assist you, and
if necessary, arrange for service.
E370.book Page 95 Tuesday, April 18, 2006 5:40 PM
Index
A
ABC mode, text input • 23
Alarm • 40
Answering
call • 26
second call • 28
Anykey answer • 76
Auto redial • 76
B
Background image • 77
Backlight time, set • 78
Band selection • 82
Barring, calls • 80
Battery
charging • 7
low indicator • 8
precautions • 89
Bluetooth
receiving, data • 84
sending, data • 84
settings • 82
Broadcast messages • 61
Browser, web • 42
C
Calculator • 40
Calendar • 65
Call costs • 31
Call records
dialled • 30
missed • 30
received • 30
Caller group • 33
Caller ID • 81
Calls
answering • 26
barring • 80
diverting • 80
holding • 27
making • 25
redialling • 25
rejecting • 26
transferring • 28
waiting • 81
Camera
photos • 69
videos • 72
CB (Cell Broadcast) messages •
61
Characters, enter • 23
Connection tone • 79
Converter • 41
Creating messages
e-mail • 48
MMS • 46
SMS • 46
D
Date, set • 74
Deleting
calendar item • 68
call records • 30
e-mail • 52, 53, 54
MMS • 50, 52, 54
Phonebook • 32, 35
SMS • 50, 52, 54
Dialled calls • 30
Display
backlight, set • 79
brightness • 77
icons • 10
language • 75
layout • 10
settings • 77
Diverting, calls • 80
DRM (Digital Rights
Management) • 61
DTMF tones, send • 28
E
E-mails
creating/sending • 48
deleting • 53
setting • 58
viewing • 52
Emergency calls • 92
F
FDN (Fixed Dialling Number)
mode • 85
File manager • 61
G
Games • 38
Greeting message • 75
H
Health and safety • 88
Holding, call • 27
95
E370.book Page 96 Tuesday, April 18, 2006 5:40 PM
Index
I
Icons, description • 10
Images, downloaded • 62
Inbox, messages
e-mail • 52
SMS/MMS • 49
International calls • 25
Internet • 42
J
Java applications • 38
K
Keypad tones
sending/muting • 28
setting • 78
volume • 78
L
Language, select • 75
Last number, redial • 25
Locking
media contents • 85
phone • 85
SIM card • 85
Low battery indicator • 8
96
M
Memory status
downloaded items • 65
phone • 85
Phonebook • 35
Message tone • 78
Messages
e-mail • 48, 52
greeting • 75
MMS • 46, 50
SMS • 45, 49
Minute minder • 79
Missed alarm items • 69
Missed calls • 30
MMS messages
creating/sending • 46
setting • 55
viewing • 49
Multiparty-call • 28
Music player • 35
Music, downloaded • 63
N
Name card • 34
Names
entering • 23
searching • 31
Network band, select • 82
Network selection • 81
Network services • 80
O
Outbox, messages • 51
P
Password
call barring • 81
phone • 85
Phone
care and maintenance •
93
display • 10
icons • 10
locking • 85
password • 85
resetting • 86
switching on/off • 8
unpacking • 6
Phonebook
adding • 32
copying • 32
deleting • 32, 35
editing • 32
finding • 31
managing • 35
options • 32
speed dialling • 34
Photos
taking • 69
viewing • 62
PIN, change • 85
PIN2, change • 85
Power on/off tone • 78
Privacy • 85
Problems, solve • 86
Q
Quiet mode
entering • 13
setting • 79
R
Received calls • 30
Received message
e-mail • 52
SMS/MMS • 49
Recording
videos • 72
voice memos • 37
Redialling
automatically • 76
E370.book Page 97 Tuesday, April 18, 2006 5:40 PM
S
Safety
information • 88
precautions • 1
SDN (Service Dialling
Numbers) • 35
Security, calls • 84
Sent messages • 52
SIM card
inserting • 7
locking • 85
Slide tone • 79
SMS messages
creating/sending • 45
setting • 55
viewing • 49
Sound settings • 78
Sounds, downloaded • 64
Speakerphone feature • 27
Speed dial • 34
Stopwatch • 42
Switching on/off
microphone • 28
phone • 8
Index
manually • 25
Resetting phone • 86
Ringer
incoming calls • 78
messages • 78
Road safety • 90
Roaming • 81
T
Text input mode, change • 23
Text, enter • 23
Time, set • 74
Timer • 41
V
Videos
recording • 72
viewing • 63
Voice clarity • 28, 77
Voice memos
playing • 38
recording • 37
W
Waiting call • 81
Wallpaper • 77
Web browser
access • 42
cache, clear • 44
World time • 39
97
E370.book Page 98 Tuesday, April 18, 2006 5:40 PM
GSM900/GSM1800/GSM1900 with Bluetooth
Portable Cellular Telephone
(Product description)
SGH-E370
(Model name)
Manufactured at :
‫ ڈ‬Samsung Electronics Co., Ltd, 94-1, Imsoo-Dong, Gumi City, Kyung-Buk, Korea,
730-350
(factory name, address)
to which this declaration relates, is in conformity with the following standards and/or other normative
documents.
Safety
: EN 60950-1:2001
EMC
: EN 301 489-01 v1.4.1 (08-2002)
EN 301 489-07 v1.2.1 (08-2002)
EN 301 489-17 v1.2.1 (08-2002)
SAR
: EN 50360:2001
EN 50361:2001
Network
: EN 301 511 v9.0.2 (03-2003)
EN 300 328 v1.6.1 (11-2004)
We hereby declare that [all essential radio test suites have been carried out and that] the above named
product is in conformity to all the essential requirements of Directive 1999/5/EC.
The conformity assessment procedure referred to in Article 10 and detailed in Annex[ญ] of Directive
1999/5/EC has been followed with the involvement of the following Notified Body(ies):
BABT, Balfour House, Churchfield Road,
Walton-on-Thames, Surrey, KT12 2TD, UK
Identification mark:
0168
The technical documentation kept at :
Samsung Electronics QA Lab.
which will be made available upon request.
(Representative in the EU)
Samsung Electronics Euro QA Lab.
Blackbushe Business Park,Saxony Way,
Yateley, Hampshire,GU46 6GG, UK
2006.03.31
(place and date of issue)
Yong-Sang Park / S. Manager
(name and signature of authorized person)
ଖ It is not the address of Samsung Service Centre. For the address or the phone number of Samsung
Service Centre, see the warranty card or contact the retailer where you purchased your phone.
E370_R&TTE.fm Page 99 Tuesday, April 18, 2006 6:22 PM
Declaration of Conformity (R&TTE)
For the following product :
E370.book Page 1 Tuesday, April 18, 2006 5:40 PM
* Depending on the software installed or your service provider or country,
some of the descriptions in this guide may not match your phone exactly.
* Depending on your country, your phone and accessories may appear
different from the illustrations in this guide.
World Wide Web
http://www.samsungmobile.com
Printed in Korea
Code No.:GH68-09866A
English (EU) 04/2006. Rev. 1.0
Download PDF

advertising