Samsung | SGH-X200 | Samsung SGH-X200 User Manual

X200.book Page 1 Friday, October 14, 2005 10:31 AM
* Depending on the software installed or your service provider or country,
some of the descriptions in this guide may not match your phone exactly.
* Depending on your country, your phone and accessories may appear
different from the illustrations in this guide.
World Wide Web
http://www.samsungmobile.com
Printed in India
Code No.:GH68-07973A
English. 10/2005. Rev 1.0
X200.book Page 2 Friday, October 14, 2005 10:31 AM
SGH-X200
User’s Guide
X200.book Page 3 Friday, October 14, 2005 10:31 AM
Drive safely at all times
Do not use a hand-held phone while driving. Park
the vehicle first.
Important
safety
precautions
Failure to comply with the following
precautions may be dangerous or illegal.
Switch off the phone when refuelling
Do not use the phone at a refuelling point (service
station) or near fuels or chemicals.
Switch off in an aircraft
Wireless phones can cause interference. Using them
in an aircraft is both illegal and dangerous.
Switch off the phone near all medical
equipment
Hospitals or health care facilities may be using
equipment that could be sensitive to external radio
frequency energy. Follow any regulations or rules in
force.
X200.book Page 1 Friday, October 14, 2005 10:31 AM
Keep your phone away from small children
All wireless phones may be subject to interference,
which could affect their performance.
Keep the phone and all its parts, including accessories,
out of the reach of small children.
Be aware of special regulations
Accessories and batteries
Meet any special regulations in force in any area and
always switch off your phone whenever it is forbidden
to use it, or when it may cause interference or danger.
Use only Samsung-approved accessories and
batteries. Use of any unauthorised accessories could
damage your phone and may be dangerous.
Water resistance
Your phone is not water-resistant. Keep it dry.
Sensible use
Use only in the normal position (held to the ear). Avoid
unnecessary contact with the antenna when the phone
is switched on.
Emergency calls
Key in the emergency number for your present
location, then press
.
Important safety precautions
Interference
• The phone could explode if the battery is
replaced with an incorrect type.
• Dispose of used batteries according to the
manufacturer’s instructions.
Qualified service
Only qualified service personnel may repair your
phone.
For more detailed safety information, see "Health and
safety information" on page 60.
1
X200.book Page 2 Friday, October 14, 2005 10:31 AM
About this Guide
This User’s Guide provides you with condensed
information about how to use your phone. To quickly
learn the basics for your phone, please refer to “Get
started” and “Step outside the phone.”
In this guide, the following instruction icons appear:
Indicates that you need to pay careful
attention to the subsequent information
regarding safety or phone features.
→
2
Indicates that you can get more information
on the referenced page.
Indicates that you need to press the
Navigation keys to scroll to the specified
option and then select it.
[ ]
Indicates a key on the phone. For example,
[
]
< >
Indicates a soft key, whose function is
displayed on the phone screen. For example,
<Menu>
•
Tri-band operation
Use your phone in worldwide GSM networks, in
any of 900, 1800, and 1900 bands.
Special features of your phone
•
Simple, compact design with Intenna
Samsung’s powerful intenna technology allows
the best call quality without an annoying
external antenna.
•
IrDA
Send and receive Phonebook
data via an infrared port.
X200.book Page 3 Friday, October 14, 2005 10:31 AM
•
•
Java
Enjoy Java™-based embedded
games and download new
games.
•
Phonebook
Store home, office, or cellular
phone numbers for your entries.
Multimedia Message Service (MMS)
Send and receive MMS messages with a
combination of text, images, and sounds.
•
Calendar and to do list
Keep track of your daily and
monthly schedules and tasks.
•
Alarm
Use your phone as an alarm
clock to wake you up in the
morning or notify you to an
event.
•
Calculator
Perform basic calculations and
do currency conversions.
•
Voice recorder
Record memos or sounds.
Special features of your phone
•
Web browser
Access the wireless web to get
current information and up-tothe-minute a wide variety of
media content.
3
X200.book Page 4 Friday, October 14, 2005 10:31 AM
Send messages ...................................................... 16
View messages....................................................... 18
Contents
Unpack
6
Your phone
6
Enter text
19
ABC, T9, Number, and Symbol mode
Buttons, features, and locations
Get started
Install and charge the phone ..................................... 7
Power on or off........................................................ 8
Keys and display ..................................................... 9
Access menu functions ............................................ 11
Customise your phone ............................................. 12
Make/Answer calls .................................................. 14
14
Begin with games, web, messages, and other special
features
Play games ............................................................ 14
Browse the web...................................................... 15
Use Phonebook....................................................... 16
4
22
Advanced calling features
7
First steps to operating your phone
Step outside the phone
Call functions
Menu functions
27
All menu options listed
Solve problems
58
Help and personal needs
Health and safety information
60
Index
67
X200.book Page 5 Friday, October 14, 2005 10:31 AM
Overview of menu functions
To access Menu mode, press <Menu> in Idle mode.
1 SIM AT
p. 27
2
2 Call records
p. 27
1
2
3
4
5
6
p. 27
p. 28
p. 28
p. 28
p. 28
p. 28
Missed calls
Received calls
Dialled calls
Delete all
Call time
Call cost*
3 Network services
p. 29
1
2
3
4
5
6
7
p. 29
p. 30
p. 30
p. 30
p. 31
p. 31
p. 31
Call diverting
Call barring
Call waiting
Network selection
Caller ID
Closed user group
Band selection
4 Sound settings
p. 32
6 Funbox
p. 42
8 Phonebook
p. 50
1
2
3
4
5
6
7
8
9
p. 32
p. 32
p. 32
p. 32
p. 32
p. 33
p. 33
p. 33
p. 33
1
2
3
4
5
6
p. 42
p. 44
p. 45
p. 45
p. 45
p. 45
1
2
3
4
5
6
7
8
Search
New entry
Group search
Edit group
Speed dial
Delete all
Memory status
SDN*
p. 50
p. 50
p. 51
p. 51
p. 51
p. 52
p. 52
p. 52
9 Phone settings
p. 53
1
2
3
4
5
6
7
8
9
p. 53
p. 54
p. 55
p. 55
p. 55
p. 55
p. 57
p. 57
p. 57
Ring tone
Ring volume
Alert type
Keypad tone
Message tone
Alert on call
Folder tone
Power on/off
Extra tones
5 Messages
p. 33
1 Text messages
2 Multimedia
messages
3 Push messages
p. 33
p. 37
p. 41
WAP browser
Games
Sounds
Images
Delete all
Memory status
7 Organiser
p. 46
1
2
3
4
5
6
7
p. 46
p. 46
p. 47
p. 48
p. 48
p. 49
p. 49
Alarm
Calendar
Time & Date
Calculator
To do list
Voice memo
Currency exchange
Infrared activate
Display settings
Greeting message
Own number
Language
Security
Extra settings
Short cut
Reset settings
*Shows only if supported by your
SIM card.
5
X200.book Page 6 Friday, October 14, 2005 10:31 AM
Unpack
Your phone
Make sure you have each item
Buttons, features, and locations
Earpiece
Display
Phone
Travel adapter
Navigation keys
(Up/Down/Left/
Right)
Battery
User’s guide
You can obtain various accessories from your local
Samsung dealer.
The items supplied with your phone and the accessories
at your Samsung dealer may vary, depending on your
country or service provider.
6
Headset jack
Left soft key
Volume keys
Dial key
Alphanumeric
keys
Infrared port
Web access/
Confirm key
Right soft key
Power on/off/
Menu exit key
Cancel/Correct
key
Special
function keys
Microphone
X200.book Page 7 Friday, October 14, 2005 10:31 AM
Get started
Install the battery.
Replace the cover.
Plug the travel adapter
into the phone.
Plug the adapter into
a standard AC wall
outlet.
First steps to operating your phone
SIM card information
When you subscribe to a cellular network, you receive
a plug-in SIM (Subscriber Identity Module) card
loaded with your subscription details, such as your
PIN, and available optional services.
Install and charge the phone
Remove the battery
cover.
If the phone is already
on, first turn it off by
holding [
].
Insert the SIM card.
Make sure that the
gold-coloured contacts
on the card face down
into the phone.
7
X200.book Page 8 Friday, October 14, 2005 10:31 AM
Get started
When the phone is completely charged (the
battery icon becomes still), unplug the adapter
from the power outlet.
Remove the adapter from the phone.
Power on or off
Power on
Do not turn on
the phone when
mobile phone
use is prohibited.
Power off
Low battery indicator
When the battery is low:
• a warning tone sounds,
• the battery low message displays, and
• the empty battery icon
blinks.
8
If the battery level becomes too low, the phone
automatically turns off. Recharge your battery.
1. Open the phone.
2. Press and hold [
the phone.
] to turn on
3. If necessary, enter the PIN and
press <OK>.
1. Open the phone.
2. Press and hold [
].
X200.book Page 9 Friday, October 14, 2005 10:31 AM
Keys and display
Keys
In Idle mode, access your favourite menus
directly.p. 57
In Menu mode, scroll through menu options.
Enter numbers, letters, and some special
characters.
In Idle mode, press and hold [1] to access
your voicemail server. Press and hold [0] to
enter an international call prefix.
In Idle mode, launch the web browser.
In Menu mode, select the highlighted menu
option or confirm input.
Enter special characters.
In Idle mode, press and hold [ ] to activate
or deactivate Silent mode. Press and hold
[ ] to enter a pause between numbers.
Make or answer a call.
In Idle mode, retrieve the recent numbers
dialled, missed, or received.
Adjust the phone volume.
In Idle mode, adjust the keypad tone
volume.
Get started
Perform the function indicated on the bottom
line of the display.
End a call.
Press and hold to switch the phone on or off.
In Menu mode, cancel input and return the
phone to Idle mode.
Delete characters from the display.
In Menu mode, return to the previous menu
level.
9
X200.book Page 10 Friday, October 14, 2005 10:31 AM
Get started
Display
Layout
Icons
display various icons.
Icons
IrDA feature activep. 53
(continued)
Roaming
New text message
New voicemail message
Menu
Icons
Phonebook
Text and graphics
display messages,
instructions, and
information you enter.
New multimedia message
Soft key function
indicators
show the current functions
assigned to the two soft
keys.
Mute modep. 25
Received signal strength
Call in progress
Out of your service area; you
cannot send or receive calls
GPRS network
Call diverting feature active
p. 29
10
Active Silent mode or call ringer set
to vibratep. 13, p. 32
Alarm set
Battery power level
X200.book Page 11 Friday, October 14, 2005 10:31 AM
Access menu functions
Use the soft
keys
Menu
Press the left soft
key to access
Menu mode.
Select an
option
1. Press the appropriate soft key.
2. Press the Navigation keys to
move to the next or previous
option.
Get started
The roles of the soft keys vary
depending on the function you are
using. The bottom line of the
display indicates their current role.
3. Press <Select>, <OK>, or
[
] to confirm the function
displayed or option highlighted.
Phonebook
4. To exit, choose either of the
following methods:
• Press < > or [C] to move
up one level.
• Press [ ] to return to Idle
mode.
Press the right soft
key to access the
Phonebook menu.
Use shortcuts
Press the number key
corresponding to the option you
want.
11
X200.book Page 12 Friday, October 14, 2005 10:31 AM
Get started
Customise your phone
Display
language
1. In Idle mode, press <Menu>
and select Phone settings →
Language.
2. Select a language.
Call ringer
melody and
volume
1. In Idle mode, press <Menu>
and select Sound settings →
Ring tone.
2. Select a ringtone.
3. Select Ring volume.
4. Adjust the volume level.
5. Press <OK>.
12
Idle mode
wallpaper
You can set wallpaper for the idle
screen.
1. In Idle mode, press <Menu>
and select Phone settings →
Display settings →
Wallpaper → Wallpaper list.
2. Select the image you want.
3. Press <Select>.
X200.book Page 13 Friday, October 14, 2005 10:31 AM
Menu
shortcuts
You can set the Navigation keys as
shortcuts to access your favourite
menus.
2. Select a key.
3. Select a menu to be assign to
the key.
Silent mode
You can switch the phone to Silent
mode to avoid disturbing other
people with your phone sounds.
Press and hold [ ] in Idle mode.
You can protect the phone against
unauthorised use with a phone
password. The phone will require
the password on power-up.
Get started
1. In Idle mode, press <Menu>
and select Phone settings →
Short cut.
Phone lock
1. In Idle mode, press <Menu>
and select Phone settings →
Security → Change
password.
2. Enter the default password,
00000000, and press <OK>.
3. Enter a new 4- to 8-digit
password and press <OK>.
4. Enter the new password again
and press <OK>.
5. Select Phone lock.
6. Select Enable.
7. Enter the password and press
<OK>.
13
X200.book Page 14 Friday, October 14, 2005 10:31 AM
Make/Answer calls
Make a call
Step outside the phone
1. Enter an area code and phone
number.
Begin with games, web, messages, and other special
features
2. Press [
Play games
].
3. To end the call, press [
Answer a call
1. When the phone is ringing,
press [ ].
2. To end the call, press [
Adjust the
volume during
a call
14
].
Press [ / ].
].
Launch a game 1. In Idle mode, press <Menu>
and select Funbox → Games
→ a game.
2. Select START GAME.
3. Select a game mode or press
any key to start the game.
X200.book Page 15 Friday, October 14, 2005 10:31 AM
Play
BubbleSmile
1. Press the Navigation keys to
move the selection.
Play Fun2Link
1. Press the Navigation keys to
move the selection to the
position you want to connect
the pipe.
2. Press [
] to insert a pipe.
3. Repeat until you complete the
pipeline.
Using a built-in web browser, you can get easy access
to the wireless web to get a variety of up-to-date
services and information and to enjoy downloads of
web content.
Launch the
web browser
Navigate the
browser
In Idle mode, press [
•
•
•
•
Step outside the phone
2. Press [1] or [3] to make a
horizontal or vertical line of
three identical bubbles.
Browse the web
].
To scroll through browser items,
press [Up] or [Down].
To select an item, press [
].
To return to the previous page,
press [C].
To access browser options,
press and hold [ ].
15
X200.book Page 16 Friday, October 14, 2005 10:31 AM
Step outside the phone
Use Phonebook
Find an entry
Add an entry
To the phone’s memory:
1. In Idle mode, enter a phone
number and press <Save>.
2. Select a number type.
3. Select Phone.
4. Enter a name and press <OK>.
5. Press <OK> to save the entry.
To the SIM card:
1. In Idle mode, enter a phone
number and press <Save>.
1. In Idle mode, press
<Phonebook> and select
Search.
2. Select an entry.
3. Scroll to a number and press
[ ] to dial, or press
<Options> to access options.
Send messages
1. In Idle mode, press <Menu>
Send a text
and select Messages → Text
message (SMS)
messages → Write new.
2. Select a number type.
2. Enter the message text.
3. Select SIM.
3. Press <Options> and select
Save and send or Send only.
4. Enter a name and press <OK>.
5. Press <OK> to save the entry.
4. If you selected Save and send,
select a memory location.
5. Enter a destination number and
press <OK>.
16
X200.book Page 17 Friday, October 14, 2005 10:31 AM
1. In Idle mode, press <Menu>
and select Messages →
Multimedia messages →
Write new.
7. Enter a destination number or
address, or select a number
from Phonebook and press
<OK>.
2. Enter the message subject
press <OK>.
8. To add other destinations,
select Add destination and
repeat from step 6.
3. Select Add here and add
message contents.
4. When you have finished, press
<Options> and select Send.
5. Select a destination type.
6. Select one of Phone number,
E-mail address, or
Phonebook.
Step outside the phone
Send a
multimedia
message
(MMS)
9. To add destinations of other
types, press < > and repeat
from step 5.
10. When you have finished, select
Send message.
17
X200.book Page 18 Friday, October 14, 2005 10:31 AM
Step outside the phone
View messages
View a text
message
When a notification appears:
1. Press <View>.
2. Select a message from the
Inbox.
From the Inbox:
1. In Idle mode, press <Menu>
and select Messages → Text
messages → Inbox.
2. Select the message.
View a
multimedia
message
When a notification appears:
1. Press <View>.
2. Press <Options> and select
Retrieve.
3. Select a message from the
Inbox.
From the Inbox:
1. In Idle mode, press <Menu>
and select Messages →
Multimedia messages →
Inbox.
2. Select the message.
18
X200.book Page 19 Friday, October 14, 2005 10:31 AM
•
•
Enter text
ABC, T9, Number, and Symbol mode
You can enter text for some features such as
messaging, Phonebook, or Organiser, using ABC
mode, T9 mode, Number mode, and Symbol mode.
Changing the text input mode
: Number mode
None: Symbol mode
Using ABC mode
Press the appropriate key until the character you want
appears on the screen.
Characters in order displayed
Key
Upper case
The text input mode indicator displays when the
cursor is in a text field.
Lower case
Write new
Options
Text input mode
indicator
Press the right soft key to change the input mode:
•
: ABC mode
•
: T9 mode
space
19
X200.book Page 20 Friday, October 14, 2005 10:31 AM
Enter text
Tips for using ABC mode
Using T9 mode
•
T9 is a predictive text input mode that allows you to
key in any character using single keystrokes.
•
•
•
•
20
To enter the same letter twice or to enter a
different letter on the same key, wait for the cursor
to move to the right automatically or press [Right].
Then, enter the next letter.
Press [ ] to insert a space.
Press [ ] to change case. Initial capital ( ),
Capital lock ( ), and Lower case ( ) are
available.
Press the Navigation keys to move the cursor.
Press [C] to delete characters one by one. Press
and hold [C] to clear the display.
Entering a word in T9 mode
1. Press [2] to [9] to start entering a word. Press
each key once for each letter.
For example, press [4], [3], [5], [5], and [6] to
enter Hello in T9 mode.
T9 predicts the word that you are typing, and it
may change with each key that you press.
2. Enter the whole word before editing or deleting
characters.
3. When the word displays correctly, go to step 4.
Otherwise, press [0] to display alternative word
choices for the keys that you have pressed.
For example, Of and Me use [6] and [3].
4. Press [ ] to insert a space and enter the next
word.
X200.book Page 21 Friday, October 14, 2005 10:31 AM
Tips for using T9 mode
Using Number mode
•
Number mode enables you to enter numbers.
•
•
Adding a new word to the T9 dictionary
This feature may not be available for some languages.
1. Enter the word that you want to add.
2. Press [0] to display alternative words for your key
presses. When there are no more alternative
words, Add displays on the bottom line.
3. Press <Add>.
4. Enter the word you want using ABC mode and
press <OK>.
Press the keys corresponding to the digits you want.
Enter text
•
Press [1] to enter periods or apostrophes
automatically.
Press [ ] to change case. Initial capital ( ),
Capital lock ( ), and Lower case ( ) are
available.
Press [Left] or [Right] to move the cursor.
Press [C] to delete characters one by one. Press
and hold [C] to clear the display.
Using Symbol mode
Symbol mode enables you to insert symbols.
To
Press
display more symbols
[Up] or [Down].
select a symbol
the corresponding
number key.
clear the symbol(s)
[C].
insert the symbol(s)
<OK>.
21
X200.book Page 22 Friday, October 14, 2005 10:31 AM
Call functions
Advanced calling features
Making a call
1. In Idle mode, enter the area code and phone
number.
2. Press [ ].
• Press [C] to clear the last digit or press and hold
[C] to clear the whole display. You can move the
cursor to edit an incorrect digit.
• Press and hold [ ] to enter a pause between
numbers.
Making an international call
1. In Idle mode, press and hold [0]. The + character
appears.
2. Enter the country code, area code, and phone
number, then press [ ].
22
Redialling recent numbers
1. In Idle mode, press [ ] to display the list of
recent numbers.
2. Scroll to the number you want and press [ ].
Making a call from Phonebook
Once you have stored a number in Phonebook, you
can dial the number by selecting it from
Phonebook.p. 50
You can also use the speed dial feature to assign your
most frequently called numbers to specific number
keys.p. 51
Dialling a number from the phone’s memory
1. In Idle mode, press and hold [0]. A + appears.
2. Enter the location number for the phone number
you want and press [ ].
3. Press [Up] or [Down] to scroll through other
numbers.
4. Press <Dial> or [ ] to dial the number you want.
X200.book Page 23 Friday, October 14, 2005 10:31 AM
Ending a call
Close the phone or press [
].
Answering a call
When you receive an incoming call, the phone rings
and displays the incoming call image.
Press <Accept> or [
] to answer the call.
Tips for answering a call
•
When Anykey answer is active, you can press
any key to answer a call, except for <Reject> or
[ ].p. 57
•
•
When Active folder is active, you can simply open
the phone.p. 57
Press <Reject> or [ ] to reject a call.
Call functions
Dialling a number from the SIM card
1. In Idle mode, enter the location number for the
phone number you want and press [ ].
2. Press [Up] or [Down] to scroll through other
numbers.
3. Press <Dial> or [ ] to dial the number you want.
Viewing missed calls
If you have missed calls, the screen displays how
many calls you have missed.
1. Press <View>.
2. If necessary, scroll through the missed calls.
3. Press [ ] to dial the number you want.
Using the headset
Use the headset to make or answer calls without
holding the phone.
Connect the headset to the jack on the left side of the
phone.
23
X200.book Page 24 Friday, October 14, 2005 10:31 AM
Call functions
The button on the headset works as listed below:
Options during a call
You can make another call if your network supports it.
1. Press <Hold> to put the call on hold.
2. Make the second call in the normal way.
3. Press <Swap> to switch between the calls.
4. Press <Options> and select End held call to end
the call on hold.
5. To end the current call, press [ ].
You can access a number of functions during a call.
Answering a second call
Adjusting the volume during a call
You can answer an incoming call, if your network
supports it and you have activated the call waiting
feature.p. 30
1. Press [ ] to answer the call. The first call is
automatically put on hold.
2. Press <Swap> to switch between the calls.
3. Press <Options> and select End held call to end
the call on hold.
4. To end the current call, press [ ].
To
Press
redial the last call
the button twice.
answer a call
the button.
end a call
the button.
Use [ / ] to adjust the earpiece volume during a call.
Press [ ] to increase the volume level and [ ] to
decrease the volume level.
Placing a call on hold/Retrieving
Press <Hold> or <Unhold> to place the call on hold
or retrieve the call.
24
Making a second call
X200.book Page 25 Friday, October 14, 2005 10:31 AM
Using the Speakerphone feature
Muting or sending key tones
Use your phone as a speaker phone to talk and listen
with the phone a short distance away.
You can turn the key tones off or on.
Transferring a call
You can transfer the currently active call to a caller on
hold, if your network supports it. With this option, the
two callers can talk to each other, but you are
disconnected from the call.
Press <Options> and select Transfer.
Using the menu functions
Press <Options> and select Menu.
Switching off the microphone (Mute mode)
You can temporarily switch off your phone’s
microphone so that the other person on the phone
cannot hear you.
Press <Options> and select Mute or Unmute.
Press <Options> and select Mute keys or Send
keys.
Call functions
Press <Options> and select Speaker ON/Normal.
To communicate with answering machines or
computerised telephone systems, Send keys must
be selected.
Sending a sequence of DTMF tones
Dual tone multi-frequency (DTMF) tones are the tones
used in phones for tone dialling.
You can send DTMF tones as a group after entering the
entire number you need to send or retrieving a
number from Phonebook. This feature is helpful for
entering a password or an account number when you
call an automated system, like a banking service.
1. When connected with a teleservice system, press
<Options> and select Send DTMF.
2. Enter the number you need to send and press
<OK>.
25
X200.book Page 26 Friday, October 14, 2005 10:31 AM
Call functions
Using Phonebook
You can access the Phonebook menu to locate or
store entries.p. 50
Press <Options> and select Phonebook.
Making a multi-party call
Use this feature to allow as many as six people to join
a multi-party call, or conference call.
Your service provider must support multi-party calls
for you to use this feature.
Setting up a multi-party call
1. Call the first participant.
2. Call the second participant. The first call is
automatically put on hold.
3. Press <Options> and select Join. The first
participant is added to the multi-party call.
4. If desired, call another person or answer an
incoming call.
5. Press <Options> and select Join.
6. Repeat steps 4 and 5 as desired.
26
Having a private conversation with one
participant
1. Press <Options> and select Select one.
2. Select a name or number from the participant list.
3. Select Private.
You can talk privately with that person, while the
other participants converse with each other.
4. To return to the multi-party call, press <Options>
and select Join.
Disconnecting one participant
1. Press <Options> and select Select one.
2. Select a name or number from the participant list.
3. Select Remove.
The participant is dropped from the call, but the
call continues with the other parties.
4. Press [ ] to end the multi-party call.
X200.book Page 27 Friday, October 14, 2005 10:31 AM
Menu functions
All menu options listed
SIM AT (Menu 1)
This menu is available if you use a SIM AT card that
provides additional services, such as news, weather,
sports, entertainment, and location services. Available
services may vary, depending on your service
provider’s plans.
For details, see your SIM card instructions or contact
your service provider.
To access this menu, press <Menu> in Idle mode and
select SIM AT.
Call records
(Menu 2)
Use this menu to view the calls you have dialled,
received, or missed, the length of your calls, and the
cost of your calls.
To access this menu, press <Menu> in Idle mode and
select Call records.
Missed calls (Menu 2.1)
This menu displays the most recently received calls
that you did not answer.
Accessing a call record
1. Select a call record.
2. Press [Up] or [Down] to move to another call
record.
3. Press [ ] to dial or, <Options> to access call
record options.
27
X200.book Page 28 Friday, October 14, 2005 10:31 AM
Menu functions
Using call record options
Call time (Menu 2.5)
While viewing call details, press <Options> to access
the following options:
• Edit: change the number of the selected call
record.
• Delete: delete the selected call record.
This menu displays the time log for calls made and
received. The actual time invoiced by your service
provider will vary.
• Last call time: check the length of your last call.
• Total sent: check the total length of all the calls
you have dialled.
• Total received: check the total length of all the
calls you have received.
• Reset timers: reset the call timers. You need to
enter the phone password.
Received calls (Menu 2.2)
This menu displays the most recent calls you have
received.
Dialled calls (Menu 2.3)
This menu displays the most recent calls you have
dialled.
Delete all (Menu 2.4)
Use this menu to delete all of the records in each call
type.
1. Press [
] to select the call types to be cleared.
2. Press <Delete>.
3. Press <Yes> twice to confirm the deletion.
28
The password is preset to 00000000. You can
change this password.p. 56
Call cost (Menu 2.6)
This network feature displays the cost of calls. This
menu is available only if your SIM card supports this
feature. Note that this is not intended to be used for
billing purposes.
• Last call cost: check the cost of your last call.
X200.book Page 29 Friday, October 14, 2005 10:31 AM
•
•
•
Network services (Menu 3)
Use this menu to access network services. Please
contact your service provider to check their availability
and subscribe to them, if you wish.
To access this menu, press <Menu> in Idle mode and
select Network services.
This network service reroutes incoming calls to a
phone number that you specify.
1. Select a call diverting option:
• Divert always: divert all calls.
• Busy: divert calls when you are on another
call.
• No reply: divert calls when you do not answer
the phone.
• Unreachable: divert calls when you are not in
an area covered by your service provider or
when your phone is switched off.
• Cancel all: cancel all call diverting options.
2. Select the type of calls to be diverted.
3. To activate call diverting, press <Activate>.
Otherwise, press <Options> and select Remove.
4. Enter the number to which calls are to be diverted
and press <OK>.
Network services
•
Call diverting (Menu 3.1)
Menu functions
•
Total cost: check the total cost of all of your calls.
If the total cost exceeds the maximum cost set in
Set max cost, you must reset the counter before
you can make another call.
Max cost: check the maximum cost limit set in
Set max cost.
Reset counters: reset the cost counters.
Set max cost: set the maximum cost authorised
for your calls.
Price/Unit: set the price per unit that is applied
when the cost of your calls is calculated.
29
X200.book Page 30 Friday, October 14, 2005 10:31 AM
Menu functions
5. If you selected No reply, select the length of time
the network delays before diverting a call and
press <Select>.
Call barring (Menu 3.2)
This network service allows you to restrict your calls.
1. Select a call barring option:
• All outgoing: prohibit all outgoing calls.
• International: prohibit international calls.
• International except home: only allow calls
to numbers within the current country when
you are abroad, and to your home country.
• All incoming: prohibit incoming calls.
• Incoming while abroad: prohibit incoming
calls when you use your phone outside of your
home country.
• Cancel all: cancel all call barring settings,
allowing calls to be sent and received normally.
• Change barring password: change the call
barring password obtained from your service
provider.
30
2. Select the type of calls to be barred.
3. Press <Activate>. To deactivate call barring,
press <Deactivate>.
4. Enter the call barring password supplied by your
service provider and press <OK>.
Call waiting (Menu 3.3)
This network service informs you when someone is
trying to reach you while you are on another call.
1. Select the type of calls to which the call waiting
option will apply.
2. Press <Activate>. To deactivate call waiting,
press <Deactivate>.
Network selection (Menu 3.4)
This network service allows you to either automatically
or manually select the network used when roaming
outside of your home area.
You can select a network other than your home
network only if there is a valid roaming agreement
between the two.
X200.book Page 31 Friday, October 14, 2005 10:31 AM
•
•
Automatic: connect to the first available network
when roaming.
Manual: select the network you want.
•
Network services
This network service allows you to prevent your phone
number from being displayed on the phone of the
person being called. However, some networks do not
allow the user to change this setting.
• Default: use the default setting provided by the
network.
• Hide number: ensure your number does not
display on the other person’s phone.
• Send number: send your number each time you
make a call.
•
Index list: list, add, or delete CUG index
numbers. Press <Options> to access the options
for setting up an index list.
Outside access: enable calls to numbers other
than those in the Closed user group. This feature
depends on the nature of your CUG subscription.
Default group: enable the default CUG, if you
have set one with your service provider. When
making a call, you are given the option of using
your default CUG, instead of selecting one from the
list.
Menu functions
Caller ID (Menu 3.5)
•
Band selection (Menu 3.7)
Closed user group (Menu 3.6)
For the phone to make and receive phone calls, it
must register with an available network. Your phone
can handle any of the following types of networks:
GSM 1900 and Combined GSM 900/1800.
Use this menu to set incoming and outgoing calls to be
restricted to a selected user group. For details about
how to create a closed user group, contact your
service provider.
The country where you purchased your phone
determines the default band that it uses. When you
travel abroad, you must remember to change to an
appropriate band.
31
X200.book Page 32 Friday, October 14, 2005 10:31 AM
Menu functions
Sound settings
(Menu 4)
Use this menu to customise various sound settings.
To access this menu, press <Menu> in Idle mode and
select Sound settings.
Ring tone (Menu 4.1)
Use this menu to select a ringtone for the call ringer.
You can select one of the default ring melodies or
downloaded sounds.
Ring volume (Menu 4.2)
Use this menu to adjust the ringtone volume.
Alert type (Menu 4.3)
Use this menu to specify how you are to be informed
of incoming calls.
• Light only: the service light flashes; the phone
neither rings nor vibrates.
• Melody: the phone rings using the selected
ringtone.
• Vibration: the phone vibrates but not rings.
32
•
Vibra+melody: the phone vibrates three times
and then starts ringing.
Keypad tone (Menu 4.4)
Use this menu to select the tone that the phone
sounds when you press a key.
You can adjust the keypad tone volume using [ / ]
in Idle mode.
Message tone (Menu 4.5)
Use this menu to change the sound settings for
incoming SMS messages, MMS messages, and CB
messages individually.
• SMS tone: specify how you are informed of new
SMS messages.
• SMS-CB tone: specify how you are informed of
new cell broadcast (CB) messages.
• MMS tone: specify how you are informed of new
MMS messages.
• Repetition: set how often the phone informs you
of new messages.
X200.book Page 33 Friday, October 14, 2005 10:31 AM
Alert on call (Menu 4.6)
Folder tone (Menu 4.7)
Use this menu to select the tone that the phone
sounds when you open or close the phone.
Power on/off (Menu 4.8)
Extra tones (Menu 4.9)
Use this menu to customise additional tones for the
phone.
• Error tone: set the phone to beep when you make
a mistake.
• Minute minder: set the phone to beep every
minute during an outgoing call to keep you
informed of the length of your call.
Connect tone: set the phone to beep when an
outgoing call is connected to the system.
Messages
(Menu 5)
Use the Messages menu to send and receive short
messages, and multimedia messages. You can also
use push message, voicemail, and cell broadcast
message features.
To access this menu, press <Menu> in Idle mode and
select Messages.
Messages (Menu 5)
Use this menu to select the melody that the phone
plays when it is switched on or off.
•
Menu functions
Use this menu to select whether or not the phone
informs you when you receive a new message or when
the time for an alarm comes during a call.
Text messages (Menu 5.1)
Short Message Service (SMS) allows you to send or
receive text messages including simple pictures,
melodies, and animated images.
33
X200.book Page 34 Friday, October 14, 2005 10:31 AM
Menu functions
34
Inbox (Menu 5.1.1)
Outbox (Menu 5.1.2)
Use this menu to view received text messages.
Use this menu to view sent or saved text messages.
While viewing a message, press <Options> to access
the following options:
• Delete: delete the message.
• Send: forward the message to other people.
• Text reply: reply to the sender.
• Call back: call the sender.
• Cut address: extract URLs, e-mail addresses, or
phone numbers from the message.
• Move to phone: move the message from the SIM
card to the phone’s memory.
• Move to SIM: move the message from the
phone’s memory to the SIM card.
• Select objects: save images or sounds from the
message into your phone.
While viewing a message, press <Options> to access
the following options:
• Delete: delete the message.
• Send: forward the message to other people.
• Cut address: extract URLs, e-mail addresses, or
phone numbers from the message.
• Move to phone: move the message from the SIM
card to the phone’s memory.
• Move to SIM: move the message from the
phone’s memory to the SIM card.
• Select objects: save images or sounds from the
message into your phone.
X200.book Page 35 Friday, October 14, 2005 10:31 AM
Templates (Menu 5.1.4)
Use this menu to create and send text messages.
1. Enter your message.
The maximum number of characters allowed in
a short message varies by service provider. If
your message exceeds the maximum number of
characters, the phone will split the message.
Use this menu to create SMS templates with the
sentences you use frequently so that you can retrieve
and insert them when composing an SMS message.
While viewing the templates list, press <Options> to
access the following options:
• Edit: edit the template.
• Send message: send the template as an SMS
message.
• Delete: delete the template.
Messages (Menu 5)
2. Press <Options> to access the following options:
• Add objects: add a sound, melody, picture, or
animated image to the message.
• Add templates: retrieve a text template.
• Add emoticon: retrieve an emoticon.
• Add phonebook: add a Phonebook entry.
• Add bookmark: add a web page’s address.
3. Press <Options> and select Send only, Save
and send or Save only.
4. If you select Save and send or Save only, select
a memory location.
5. Enter a destination number.
6. Press <OK> to send the message.
Menu functions
Write new (Menu 5.1.3)
Emoticon templates (Menu 5.1.5)
Your phone provides preset emoticons so that you can
use when writing a message. Use this menu to create
or edit emoticons.
While viewing the emoticon list, press <Options> to
access the following options:
• Add: add a new emoticon.
• Edit: edit the selected emoticon.
• Send: send a message using the emoticon.
• Delete: delete the emoticon.
35
X200.book Page 36 Friday, October 14, 2005 10:31 AM
Menu functions
Settings (Menu 5.1.6)
Use this menu to customise the SMS settings.
The setting options available in this menu may vary
depending on your service provider.
•
•
36
Setting x (where x is the setting group number):
each group has its own submenu.
Service centre: store or changes the number of
your message centre.
Default destination: store a default destination
number.
Default type: set the default message type.
Default validity: set the length of time your
messages are stored in the SMS server.
Setting name: change the name of the setting
group.
Common setting: the following options are
available:
Reply path: allow the recipient to reply to you
through your message centre.
Delivery reports: set the network to inform you
when your message has been delivered.
Bearer selection: select the GSM or GPRS
preferred bearer type.
Delete all (Menu 5.1.7)
Use this menu to delete all of SMS messages in each
message box.
1. Press [
] to select the message boxes to be
cleared.
2. Press <Delete>.
3. Press <Yes> twice to confirm the deletion.
Memory status (Menu 5.1.8)
Use this menu to check the number of SMS messages
you have stored and total number of SMS messages
you can store in each memory type.
X200.book Page 37 Friday, October 14, 2005 10:31 AM
Voice mail (Menu 5.1.9)
Use this menu to store the number of the voicemail
server and access your voicemails.
•
Broadcast (Menu 5.1.0)
The Cell Broadcast service delivers short messages on
various topics such as the weather or traffic.
Use this menu to change the settings for the service
and access broadcast messages.
• Read: open received messages.
The Volatile box saves network messages until
the phone is switched off.
•
•
Messages (Menu 5)
•
Connect to voice server: connect to the voice
server to allow you to listen to your messages. You
can also connect to the voicemail server by
pressing and holding [1] in Idle mode.
Voice server number: change the voicemail
server number.
•
Menu functions
You must enter the voice server number before you
can access your voicemails. Your service provider
can give the voice server number.
The Archive box saves network messages
indefinitely. Press <Options> and select Save
when a text notification appears. The message is
saved in the Archive box.
Receive: select to receive broadcast messages, or
not.
Channel list: specify the channels from which you
receive broadcast messages.
Language: select the preferred languages in
which broadcast messages display.
Please contact your service provider for details.
Multimedia messages (Menu 5.2)
Multimedia Message Service (MMS) delivers messages
containing a combination of text, picture, and sound,
from phone to phone or from phone to e-mail.
Inbox (Menu 5.2.1)
This menu displays MMS messages that you have
received. The following icons tell you the message
status:
37
X200.book Page 38 Friday, October 14, 2005 10:31 AM
Menu functions
•
•
•
•
•
•
•
Unread notification
Read notification
Retrieving from the server
Processing your request
Failed to send
Read
Unread
While viewing a message, press <Options> to access
the following message options:
• Delete: delete the message.
• Reply: reply to the sender.
• Callback: call the sender.
• Cut address: extract URLs, e-mail addresses, or
phone numbers from the message.
• Forward: forward the message to other people.
• Save picture: save an image from the message
into the Images folder.
• Save sound: save a sound from the message into
the Sounds folder.
38
•
Properties: access the message properties.
When you select a notification, you can access
Retrieve to retrieve the message from the MMS
server.
Outbox (Menu 5.2.2)
This menu displays MMS messages that you have
sent. The following icons tell you the message status:
•
Being sent
•
Sent
•
Failed to send
•
To be sent
While viewing a message, press <Options> to access
the following options:
• Delete: delete the message.
• Cut address: extract URLs, e-mail addresses, or
phone numbers from the message.
• Send: send or resend the message.
• Edit message: edit the message.
• Properties: access the message properties.
X200.book Page 39 Friday, October 14, 2005 10:31 AM
Draft (Menu 5.2.3)
After creating a multimedia message, you can store it
in this message box for sending later.
Write new (Menu 5.2.4)
The maximum size allowed for a message can
differ, depending on your service provider.
3. If you want to change the added items, highlight
one and press <Options> to access the following
options:
• Edit text/Edit picture/Edit sound: edit the
text, picture, or sound.
• Add page: add pages. Move to each page by
pressing [Left] or [Right] on the message
screen.
• Delete: delete the item from your message.
• Duration: set how long one page displays.
After the specified time, the display
automatically scrolls to the next page.
4. When you have finished, select Send from the
options.
5. Select a destination type (To, Cc, Bcc).
6. Select one of Phone number, E-mail address, or
Phonebook.
Messages (Menu 5)
You can create and send an MMS message.
1. Enter the message subject and press <OK>.
2. Press <Options> and add message contents using
one of the following options:
• Add text: add message text.
• Add picture: add a picture to the message.
• Add sound: add a sound clip to the message.
• Save: save the message in the Draft or
Templates box.
• Settings: change the message settings.
• Add destination: enter destination numbers
or addresses.
Preview: view the message you created.
Menu functions
You can view a message and use the options the same
as in Outbox.
•
39
X200.book Page 40 Friday, October 14, 2005 10:31 AM
Menu functions
7. Enter a phone number or an e-mail address, or
select a number from Phonebook and press <OK>.
8. To add more destinations, select Add destination
and repeat from step 6.
9. To enter additional numbers or addresses to other
destination types, press < >and repeat from step
5.
10. When you have finished, select Send message.
Templates (Menu 5.2.5)
Use this menu to store MMS messages you saved as
templates so that you can use them to create new
messages.
While viewing a message template, press <OK> to
access the following options:
• Edit message: send the message using the
template.
• Delete: delete the template.
Delete all (Menu 5.2.6)
Use this menu to delete all of MMS messages in each
message box.
40
1. Press [
] to select the message boxes to be
cleared.
2. Press <Delete>.
3. Press <Yes> twice to confirm the deletion.
Memory status (Menu 5.2.7)
Use this menu to view the amount of memory
available for MMS messages and memory currently in
use in each message box.
Setup (Menu 5.2.8)
You can customise the settings for sending and
receiving MMS messages.
• Delivery report: set the network to inform you
when your message has been delivered.
• Read reply: request a reply from the recipient.
• Auto download: set whether or not your phone
retrieves new incoming messages from the MMS
server without notifications.
• Message acceptance: select the category of
messages you want to receive.
X200.book Page 41 Friday, October 14, 2005 10:31 AM
•
•
•
•
MMS profile (Menu 5.2.9)
You can configure required network settings for MMS.
The last profile accessed is automatically activated for
sending or receiving subsequent messages.
Check with your service provider before you change
any MMS settings on your phone.
•
•
•
•
•
•
Connection URL: enter the address of your MMS
server.
Security: select a data transmission mode.
IP address: enter the gateway address.
User name: enter the user ID.
Password: enter the password.
APN: enter the access point name used for the
address of the MMS server.
Push messages (Menu 5.3)
Messages (Menu 5)
•
•
Menu functions
•
Hide ID: hide your phone number on the
recipient’s phone.
Expiry date: set the length of time your messages
are stored in the message centre.
Delivery time: set the time delay before
messages are sent.
Priority: set the priority level of your messages.
Report allowed: send a delivery report from the
network to the sender.
Page duration: set how long one page in your
outgoing messages displays. After a specified time,
the display automatically scrolls to the next page.
Use this menu to access messages from the web
server.
• Inbox: view push messages you have received.
• Receive: determine whether or not your phone
receives push messages.
Never: the phone rejects push messages.
Always: the phone receives all push messages.
• Delete all: delete all push messages.
Profile name: assign a name to the MMS profile.
41
X200.book Page 42 Friday, October 14, 2005 10:31 AM
Menu functions
Funbox
(Menu 6)
The Funbox menu allows you to use the web browser,
play Java games, and access images and sounds
stored in the phone’s memory.
To access this menu, press <Menu> in Idle mode and
select Funbox.
WAP browser (Menu 6.1)
The Wireless Application Protocol (WAP) browser on
your phone allows you to access the wireless web.
From the wireless web, you can access up-to-date
information and a wide variety of media content, such
as games, wallpapers, and ringtones.
Home (Menu 6.1.1)
Use this menu to connect your phone to the network
and load the homepage of the wireless web service
provider. You can also press [
] in Idle mode.
42
Navigating with the web browser
To
Press
scroll through browser items
[Up] or [Down].
select a browser item
[
return to the previous page
[C].
].
Using page options
From any web page, press and hold [ ] to access the
following options:
• Reload: reload the current page with updated
information.
• Home: return to the homepage.
• Go to URL: enter a URL address manually.
• Show URL: view the URL address of the current
web page.
• Edit home: change the page to be used for your
homepage.
• Clear cache: delete information stored in the
cache.
X200.book Page 43 Friday, October 14, 2005 10:31 AM
•
Inbox: read messages received from a web
server.
•
Edit: edit the URL address and title of the
bookmark.
Delete: delete the bookmark.
•
Press [
http:// (Menu 6.1.3)
] to exit the browser.
Favorite (Menu 6.1.2)
Use this menu to save URL addresses in order to
quickly access web pages.
Accessing a bookmarked page
Selecting a bookmark item launches the web browser
and accesses the associated web page.
Using bookmark options
After saving an item, press <Options> to access the
following options:
• Go to URL: access the website.
Use this menu to manually enter a URL address and
access the associated web page.
Settings (Menu 6.1.4)
Use this menu to set up servers for the web browser.
Contact your service provider for details about your
settings options.
Funbox (Menu 6)
Adding a bookmark
1. Select an empty location.
2. Enter a URL address and press <Enter>.
3. Enter a title for the bookmark and press <Enter>.
Menu functions
Exiting the web browser
For each server, the following options are available:
• Profile name: assign a name to the server profile.
• Homepage URL: set the address of your
homepage.
• Security: select a data transmission mode.
• Bearer: select a bearer for each type of network
address accessed; GPRS or Data.
When the bearer is set to GPRS:
• IP address: enter the web gateway address.
43
X200.book Page 44 Friday, October 14, 2005 10:31 AM
Menu functions
•
•
•
User name: enter the user ID.
Password: enter the password.
APN: enter the access point name of the GPRS
network gateway.
When the bearer is set to Data:
• IP address: enter the web gateway address.
• Login name: enter the user ID.
• Password: enter the password.
• Dial-up number: enter the PPP server phone
number.
• Data call type: select a data call type.
Clear cache (Menu 6.1.5)
Use this menu to clear the cache, which is the
temporary memory that stores the web pages you
have recently accessed.
44
Games (Menu 6.2)
You can download Java applications from various
sources using the web browser, and store them in your
phone.
Java services may not available, depending on your
service provider.
Launching a game
1. Select the game you want on the Games list.
2. On the startup screen of the game, you can access
the following options:
• START GAME: start a new game.
• CONTINUE: continue the last game you
played.
• HIGH SCORE: view the high score table. This
option may not be available for some games.
• HOW TO PLAY: view how to play the game
and the key functions for the game.
• OPTION: switch on or off the game sound.
3. Press [
] to confirm your selection.
X200.book Page 45 Friday, October 14, 2005 10:31 AM
Viewing game information
Images (Menu 6.4)
Scroll to the game you want and press <Info>.
This menu displays images downloaded from the
wireless web or received in messages.
Changing the DNS settings
Sounds (Menu 6.3)
Delete all (Menu 6.5)
This menu displays sounds downloaded from the
wireless web or received in messages.
Use this menu to delete all of the downloaded items in
the Games, Sounds, and Images folders.
1. Press [
] to select the folders to be cleared.
2. Press <Delete>.
3. Press <Yes> twice to confirm the deletion.
While accessing a sound, press <Options> to access
the following options:
• Rename: change the sound name.
• Delete: delete the sound.
• Set as ring tone: set the sound as your ringtone.
Funbox (Menu 6)
While accessing an image, press <Options> to access
the following options:
• Rename: change the image name.
• Delete: delete the image.
• Set as wallpaper: set the image as your
wallpaper for the idle screen.
Menu functions
You may need to change the DNS setting of the Java
server at your service provider’s instructions.
1. Select Setting on the Games list.
2. Enter the primary DNS address and press <OK>.
3. Enter the secondary DNS address and press
<OK>.
Memory status (Menu 6.6)
Use this menu to check the total amount of memory
for media items and the amount of memory currently
in use in each media box.
45
X200.book Page 46 Friday, October 14, 2005 10:31 AM
Menu functions
Organiser
(Menu 7)
The Organiser feature enables you to keep track of
your schedule and tasks, and to record voice memos.
You can also set the time and date and use convenient
features, such as an alarm clock, a calculator, and a
currency converter.
To access this menu, press <Menu> in Idle mode and
select Organiser.
Alarm (Menu 7.1)
Use this menu to set alarms to ring at a specific time.
Setting an alarm
1. Select the type of alarm.
2. Enter the time for the alarm to sound and press
[
].
3. Select AM or PM in 12-hour time format.
4. If you selected Morning call in step 1, choose
Monday to friday or Monday to saturday.
46
Stopping an alarm
•
•
•
When the alarm sounds, press any key.
To remove an alarm set, access it, press
<Options> and select Remove alarm.
To remove all alarm sets, select Remove alarm
from the Alarm screen.
Setting the alarm to ring even if the phone is
off
From the Alarm screen, select Autopower → Enable.
If the phone is off when it is time for the alarm to ring,
the phone switches on and sounds the alarm.
Calendar (Menu 7.2)
Use this menu to consult the calendar, write memos,
or set alarms to act as a reminder.
Writing a memo
1. Select a date on the calendar.
2. Enter your memo and press <OK>.
X200.book Page 47 Friday, October 14, 2005 10:31 AM
Viewing a memo
Using calendar memo options
On the calendar screen, press <Options> to access
the following options:
• Search all: view all of the memos you created.
• Delete all: delete all memos.
• Go to date: go to a specific date.
• Exit: exit the Calendar menu.
Time & Date (Menu 7.3)
Organiser (Menu 7)
1. Select a date which has memos from the calendar.
2. Press [Up] or [Down] to view other memos
scheduled for that day.
While viewing a memo, press <Options> to access
the following options:
• New: add a new memo.
• Edit: edit the memo.
• Alarm: set an alarm for the memo.
• Delete: delete the memo.
• Copy to: copy the memo to another date.
• Move to: change the date of the memo.
Menu functions
3. Press [
] to set an alarm to ring on the chosen
day.
Otherwise, press <Skip>.
4. Enter the time for the alarm and press [
].
To select an alarm melody, press <Melody>.
5. Select AM or PM in 12-hour format.
The colour of the date on the calendar changes to
pink to indicate that a memo exists for that date.
Use this menu to change the time and date displayed
on your phone. Before setting the time and date,
specify your time zone in World time.
• Set time: enter the current time.
• Set date: enter the current date.
• World time: set your local time zone and find out
what time it is in another part of the world.
• Time format: select 12-hour or 24-hour time
format.
47
X200.book Page 48 Friday, October 14, 2005 10:31 AM
Menu functions
Calculator (Menu 7.4)
4. Enter your deadline and press [
Use this menu to perform basic arithmetic functions
such as addition, subtraction, multiplication, and
division.
1. Enter the first number.
• Press <.()> to insert a decimal point or a
bracket.
• Press [ ] or [ ] to move the cursor.
2. Press the Navigation keys to access the math
function you want.
3. Enter the second number.
4. Press [
] to view the result.
5. If necessary, repeat from step 2 to continue the
calculation.
Viewing the task
To do list (Menu 7.5)
Use this menu to create tasks and manage them.
Creating a task
1. Press <New>.
2. Enter the first task and press <OK>.
3. Select a priority level.
48
].
When you select the To do list menu, the tasks display
with a check mark, if the task has been done, and a
priority level indicator;
for High,
for Normal,
and
for Low.
To change the status of a specific task, press [
].
While viewing a task or the task list, press <Options>
to access the following options:
• New: add a new task.
• Mark: change the status of the task.
• Edit: edit the task.
• Sort: sort the task by priority or status.
• Copy: copy the task.
• Copy to calendar: copy the task to the calendar
as a memo.
• Delete: delete the task.
• Delete all: delete all tasks.
• Exit: exit the To do list menu.
X200.book Page 49 Friday, October 14, 2005 10:31 AM
Voice memo (Menu 7.6)
Use this menu to record voice memos. A voice memo
can be up to 30 seconds.
Memo list (Menu 7.6.2)
Use this menu to access the list of voice memos you
have recorded.
Delete all (Menu 7.6.3)
Use this menu to delete all of the voice memos you
have recorded at one time.
Organiser (Menu 7)
1. Press <Record> to start recording.
2. Speak into the microphone.
3. When you press <Stop>, or if the recording time
expires, the following options display:
• Replay: play back your memo.
• Re-record: discard the memo and record
another one.
• Save: save the memo.
• Quit: cancel your recording and exit the Voice
memo menu.
4. Select Save to save the voice memo.
5. Enter a name of the voice memo and press <OK>.
Menu functions
Voice record (Menu 7.6.1)
Press <Options> to access the following options:
• Play: play back your voice memo.
• Send: send the voice memo via MMS.
• Rename: change the name of the voice memo.
• Properties: access the properties of the voice
memo.
• Delete: delete the voice memo.
Memory status (Menu 7.6.4)
You can check the total amount of memory and the
amount of memory currently in use for voice memos.
Currency exchange (Menu 7.7)
Use this menu to do currency conversions.
1. Enter the rate of foreign currency and press
<OK>.
49
X200.book Page 50 Friday, October 14, 2005 10:31 AM
Menu functions
2. Enter the amount of the source currency you want
to convert and press <OK>.
The amount you entered and its equivalent value
in the foreign currency display.
Phonebook
(Menu 8)
You can store phone numbers on your SIM card and in
your phone’s memory. The SIM card and phone’s
memory are physically separate, but they are used as
a single entity called Phonebook.
To access this menu, press <Menu> in Idle mode and
select Phonebook, or press <Phonebook>.
Search (Menu 8.1)
Use this menu to search for numbers in Phonebook.
Finding an entry
1. Enter the first few letters of the name that you
want to find.
2. Select an entry from the Phonebook list.
50
3. Scroll to a number and press [ ] to dial, or press
<Options> to access Phonebook options.
Using Phonebook options
While viewing an entry, press <Options> to access
the following options:
• Paste: paste the number into the normal dialling
mode.
• Edit: edit entry information.
• Delete: delete the number.
• Copy: copy the number to the phone’s memory or
SIM card.
• Caller group: assign a caller group.
• Add entry: add a new entry.
• Send via IrDA: send the entry via infrared port.
New entry (Menu 8.2)
Use this menu to add a new entry to Phonebook.
Storing an entry in the phone’s memory
1. Select a number type.
X200.book Page 51 Friday, October 14, 2005 10:31 AM
2. Select Phone.
3. Enter a name and press <OK>.
4. Enter a number or an e-mail address and press
<Save>.
5. Change the location number, if you want, and
press <OK>.
3. Select the name you want.
4. Press [ ] to dial the number or <Options> to
access Phonebook options.
Storing an entry on the SIM card
From the group list, press <Options> to access the
following options:
• Call ring tone: set a ringtone for incoming calls
from the group.
• SMS tone: set a ringtone for incoming messages
from the group.
• Graphic: set a graphic icon for incoming calls from
the group.
• Group name: assign a name to the group.
Group search (Menu 8.3)
Use this menu to search your entries in Phonebook in
caller groups.
1. Enter the first few letters of the group name.
2. Select a group and press <View>.
Use this menu to edit your caller groups’ properties.
Phonebook (Menu 8)
Select a number type.
Select SIM.
Enter a name and press <OK>.
Enter a number and press <Save>
Change the location number, if you want, and
press <OK>.
Menu functions
1.
2.
3.
4.
5.
Edit group (Menu 8.4)
Speed dial (Menu 8.5)
Use this menu to assign speed dial numbers (2 to 9) to
eight of your most frequently called numbers.
51
X200.book Page 52 Friday, October 14, 2005 10:31 AM
Menu functions
Assigning speed dial entries
Delete all (Menu 8.6)
1. Select a key location from 2 to 9. Key 1 is reserved
for your voicemail server.
2. Select an entry from the Phonebook list.
3. Select a number, if the entry has more than one
number.
Use this menu to delete all of the entries from
Phonebook.
1. Press [
] to select the locations to be cleared.
2. Press <Delete>.
3. Enter the phone password and press <OK>.
4. Press <Yes> twice to confirm the deletion.
Managing speed dial entries
While viewing the Speed dial screen, press
<Options> to access the following options:
• Change: assign a different number to a key.
• Delete: delete the speed dial setting for a key.
• Delete all: delete the speed dial settings for all
keys.
• Number: check the name and number assigned to
a key.
Dialling speed dial entries
Press and hold the appropriate key in Idle mode.
Memory status (Menu 8.7)
Use this menu to check the total number of entries
you can store and the number of the entries you have
stored in the phone’s memory or on the SIM card.
SDN (Menu 8.8)
This menu is available if your SIM card supports
Service Dialling Numbers (SDN). Use this menu to
view the list of SDNs assigned by your service
provider, including emergency numbers, directory
enquiries, and voicemail numbers.
Scroll to the number you want and press <Dial> or
[ ].
52
X200.book Page 53 Friday, October 14, 2005 10:31 AM
Phone settings
(Menu 9)
Use this menu to customise your phone settings. You
can also reset the settings to their default values.
•
align the IrDA port on the phone with the IrDA port
on your phone computer or another phone.
Menu functions
To access this menu, press <Menu> in Idle mode and
select Phone settings.
Infrared activate (Menu 9.1)
With PC (Menu 9.1.1)
Use this menu to use the infrared feature with a
computer.
To use an infrared connection, you must:
• configure and activate an IrDA-compliant infrared
port on your PC.
• activate the infrared feature on the phone; the
IrDA icon ( ) appears on the top line of the
display.
The connection is ready for data transmission.
Phone settings (Menu
Use this menu to send or receive data to or from IrDAcompatible computers or phones through the infrared
port.
If there is no communication between your phone and
the IrDA-compliant device within 30 seconds
activating the feature, it is automatically deactivated.
With other phone (Menu 9.1.2)
Use this menu to send or receive Phonebook entries
from another compliant phone.
53
X200.book Page 54 Friday, October 14, 2005 10:31 AM
Menu functions
Receiving data from another phone
1. Align the IrDA ports on both phones with each
other.
2. When the list of the received data displays, select
one of the two options:
To save an individual item:
1. Select the item you want from the list.
2. Press <Options> and select Save to save the
data.
Otherwise, select Discard to delete the data.
To save all data:
1. From the item list, press <Options> to select
one of the following options:
• Save all vCard: save all Phonebook entries.
• Discard all vCard: delete all Phonebook
entries.
2. When FDN (Fixed Dialling Number) mode is
enabled on your phone, enter the PIN2 and
press <OK>.
3. Press <Save> to save the entries.
54
Sending your Phonebook
You can send Phonebook entries via IrDA connection.
Display settings (Menu 9.2)
Use this menu to change settings for the display and
light.
Wallpaper (Menu 9.2.1)
You can change the background image and the
settings for the text of Idle mode.
• Wallpaper list: select a background image.
• Text display: determine the phone displays the
time and date.
• Text colour: select a text colour.
Brightness (Menu 9.2.2)
You can adjust the brightness of the display for
varying lighting conditions.
Contrast (Menu 9.2.3)
You can adjust the contrast of the display for varying
lighting conditions.
X200.book Page 55 Friday, October 14, 2005 10:31 AM
Backlight (Menu 9.2.4)
Greeting message (Menu 9.3)
You can select the length of time the backlight and the
display stay on.
• Backlight on: select the length of time the
backlight stays on.
• Backlight dim: select the length of time the
display is in Dimming mode after the backlight
turns off. After a specified time, the display turns
off.
Use this menu to enter the greeting that is displayed
briefly when the phone is switched on.
Graphic logo (Menu 9.2.6)
Use this menu to display your service provider’s logo
instead of its name.
Dialling font colour (Menu 9.2.7)
Use this menu to select a font colour for the numbers
entered while dialling.
Use this feature to check your phone numbers, or to
assign a name to each of the numbers. Changes made
here do not affect the actual subscriber numbers on
your SIM card.
Language (Menu 9.5)
Phone settings (Menu
The service LED on the front of the phone indicates
when service is available on the phone. Use this menu
to set whether or not the service light is used.
Menu functions
Service light (Menu 9.2.5)
Own number (Menu 9.4)
Use this menu to select one of several languages for
the display text.
Security (Menu 9.6)
Use this menu to protect the phone against
unauthorised use by managing the several access
codes of your phone and SIM card.
If you enter an incorrect PIN/PIN2 three times in
succession, the SIM card is blocked. To unblock it
you need to enter your PUK/PUK2 (Personal
Unblocking Key). The codes are supplied by your
network operator.
55
X200.book Page 56 Friday, October 14, 2005 10:31 AM
Menu functions
PIN check (Menu 9.6.1)
Privacy (Menu 9.6.5)
The 4-to 8-digit PIN (Personal Identification Number)
protects your SIM card against unauthorised use.
When this feature is enabled, the phone requires your
PIN each time it is switched on.
Change PIN (Menu 9.6.2)
Use this menu to lock your media contents, including
MMS messages, voice memos, images, and sounds.
1. Press [
] to select the items to be locked.
2. Press <OK> to lock the marked items.
3. Enter the phone password and press <OK>.
Use this menu to change your PIN. The PIN check
feature must be enabled to use this feature.
To access a locked item, you need to enter the phone
password.
Phone lock (Menu 9.6.3)
SIM lock (Menu 9.6.6)
The Phone lock feature locks the phone from
unauthorised use.
The SIM lock feature allows your phone to work only
with the current SIM by assigning a SIM lock code. You
must enter the SIM lock code to use a different SIM
card.
When this feature is enabled, you must enter a 4- to
8-digit phone password each time the phone is
switched on.
The password is preset to 00000000. To change the
password, use the Change password menu.
Change password (Menu 9.6.4)
Use this menu to change your phone password.
56
FDN mode (Menu 9.6.7)
If supported by your SIM card, Fixed Dialling Number
(FDN) mode restricts your outgoing calls to a limited
set of phone numbers. When this feature is enabled,
you can make calls only to phone numbers stored on
the SIM card.
X200.book Page 57 Friday, October 14, 2005 10:31 AM
Change PIN2 (Menu 9.6.8)
2. Select a menu to be assigned to the key.
If supported by your SIM card, the Change PIN2
feature changes your current PIN2.
Reset settings (Menu 9.9)
Enter the 4- to 8-digit phone password and press
<OK>.
The password is preset to 00000000. You can
change this password.p. 56
Phone settings (Menu
You can turn the automatic redialling or answering
feature on or off.
• Auto redial: set the phone to make up to ten
attempts to redial a phone number after an
unsuccessful call.
• Active folder: answer an incoming call by opening
the phone.
• Anykey answer: answer an incoming call by
pressing any key, except <Reject> or [ ].
Use this menu to reset the phone’s settings you have
changed.
Menu functions
Extra settings (Menu 9.7)
Short cut (Menu 9.8)
You can use the Navigation keys as shortcut keys to
access specific menus directly from Idle mode. Use
this menu to change the shortcut assignments for the
keys.
1. Select a key to be used as a shortcut key.
57
X200.book Page 58 Friday, October 14, 2005 10:31 AM
Solve problems
Solve problems
“Enter PUK”
•
Help and personal needs
To save the time and expense of an unnecessary service
call, perform the simple checks in this section before
contacting a service professional.
•
“Insert SIM card”
• Be sure that the SIM card is correctly installed.
•
“Enter PIN”
• You are using your phone for the first time. You
must enter the PIN supplied with the SIM card.
• The PIN check feature is enabled. Every time the
phone is switched on, the PIN has to be entered.
To disable this feature, use the PIN check menu.
58
“No service,” “Network failure,” or “Not
done” displays
When you switch on your phone, the
following messages may appear:
“Phone locked Enter password”
• The automatic locking function has been enabled.
You must enter the phone’s password before you
can use the phone.
The PIN code has been entered incorrectly three
times in succession, and the phone is now blocked.
Enter the PUK supplied by your service provider.
The network connection has been lost. You may be
in a weak signal area. Move and try again.
You are trying to access an option for which you
have no subscription with your service provider.
Contact the service provider for further details.
You have entered a number but it was not
dialled
•
•
•
Be sure that you have pressed [ ].
Be sure you have accessed the right cellular
network.
Be sure that you have not set an outgoing call
barring option.
X200.book Page 59 Friday, October 14, 2005 10:31 AM
Your correspondent cannot reach you
•
•
•
Be sure your phone is switched on. ([ ] pressed
for more than one second.)
Be sure you are accessing the correct cellular
network.
Be sure that you have not set an outgoing call
barring option.
Your correspondent cannot hear you speaking
•
•
Be sure you have switched off the microphone.
Be sure you are holding the phone close enough to
your mouth. The microphone is located at the
bottom of the phone.
The phone starts beeping and “Warning Low
battery” flashes on the display
•
Your battery is insufficiently charged. Recharge the
battery.
The audio quality of the call is poor
•
Check the signal strength indicator on the display
(
). The number of bars indicates the signal
strength from strong (
) to weak ( ).
•
Try moving the phone slightly or moving closer to a
window if you are in a building.
No number is dialled when you re-call a
Phonebook entry
•
•
Use the Search menu to ensure the number has
been stored correctly.
Re-store the number, if necessary.
The battery doesn’t charge properly or the
phone sometimes turns itself off
•
Wipe the charging contacts both on the phone and
on the battery with a clean soft cloth.
If the above guidelines do not help you to
solve the problem, take note of:
•
•
•
The model and serial numbers of your phone
Your warranty details
A clear description of the problem
Then contact your local dealer or Samsung after-sales
service.
59
X200.book Page 60 Friday, October 14, 2005 10:31 AM
Health and safety information
Health and safety information
SAR certification information
This phone meets European Union (EU) requirements
concerning exposure to radio waves.
Your mobile phone is a radio transmitter and receiver. It is
designed and manufactured to not exceed the limits for
exposure to radio-frequency (RF) energy, as
recommended by the EU Council. These limits are part of
comprehensive guidelines and establish permitted levels
of RF energy for the general population. The guidelines
were developed by independent scientific organisations
through the periodic and thorough evaluation of scientific
studies. The limits include a substantial safety margin
designed to ensure the safety of all persons, regardless of
age and health.
The exposure standard for mobile phones employs a unit
of measurement known as Specific Absorption Rate (SAR).
The SAR limit recommended by the EU Council is 2.0W/
kg.*
The highest SAR value for this model phone was 0.74W/kg.
60
SAR tests are conducted using standard operating
positions with the phone transmitting at its highest
certified power level in all tested frequency bands.
Although the SAR is determined at the highest certified
power level, the actual SAR level of the phone while
operating can be well below the maximum value. This is
because the phone is designed to operate at multiple
power levels so as to use only the power required to reach
the network. In general, the closer you are to a base
station, the lower the power output of the phone.
Before a new model phone is available for sale to the
public, compliance with the European R&TTE Directive
must be shown. This directive includes as one of its
essential requirements the protection of the health and
safety of the user and any other person.
* The SAR limit for mobile phones used by the public is 2.0 watts/
kilogram (W/kg) averaged over ten grams of body tissue. The
limit incorporates a substantial margin of safety to give additional protection for the public and to account for any variations
in measurements. The SAR values may vary, depending on
national reporting requirements and the network band.
X200.book Page 61 Friday, October 14, 2005 10:31 AM
Precautions when using batteries
•
•
•
•
•
•
Never use a charger or battery that is damaged in any
way.
Use the battery only for its intended purpose.
If you use the phone near the network’s base station,
it uses less power. Talk and standby time are greatly
affected by the signal strength on the cellular network
and the parameters set by the network operator.
Battery charging time depends on the remaining
battery charge, the type of battery, and the charger
used. The battery can be charged and discharged
hundreds of times, but it will gradually wear out. When
the operation time is noticeably shorter than normal, it
is time to buy a new battery.
If left unused, a fully charged battery will discharge
itself over time.
Use only Samsung-approved batteries, and recharge
your battery only with Samsung-approved chargers.
Disconnect the charger from the power source when it
is not in use. Do not leave the battery connected to a
charger for more than a week, since overcharging may
shorten its life.
•
•
•
•
Extreme temperatures will affect the charging capacity
of your battery: it may require cooling or warming
first.
Do not leave the battery in hot or cold places because
the capacity and lifetime of the battery will be
reduced. Try to keep the battery at room temperature.
A phone with a hot or cold battery may not work
temporarily, even when the battery is fully charged. Liion batteries are particularly affected by temperatures
below 0°C (32°F).
Do not short-circuit the battery. Accidental shortcircuiting can occur when a metallic object like a coin,
clip or pen causes a direct connection between the +
and – terminals of the battery (metal strips on the
battery). For example, do not carry a spare battery in
a pocket or bag where the battery may contact metal
objects. Short-circuiting the terminals may damage
the battery or the object causing the short-circuiting.
Dispose of used batteries in accordance with local
regulations. Always recycle. Do not dispose of
batteries in a fire.
61
X200.book Page 62 Friday, October 14, 2005 10:31 AM
Health and safety information
Road safety
Electronic devices
Your wireless phone gives you the powerful ability to
communicate by voice, almost anywhere, anytime. But an
important responsibility accompanies the benefits of
wireless phones, one that every user must uphold.
Most modern electronic equipment is shielded from radio
frequency (RF) signals. However, certain electronic
equipment may not be shielded against the RF signals
from your wireless phone. Consult the manufacturer to
discuss alternatives.
When driving a car, driving is your first responsibility.
When using your wireless phone while driving, follow local
regulations in the country or region you are in.
Operating environment
Remember to follow any special regulations in force in the
area you are in, and always switch off your phone
whenever it is forbidden to use it, or when it may cause
interference or danger.
When connecting the phone or any accessory to another
device, read its user’s guide for detailed safety
instructions. Do not connect incompatible products.
As with other mobile radio transmitting equipment, users
are advised that for the satisfactory operation of the
equipment and for the safety of personnel, it is
recommended that the equipment should only be used in
the normal operating position (held to your ear with the
antenna pointing over your shoulder).
62
Pacemakers
Pacemaker manufacturers recommend that a minimum
distance of 15 cm (6 inches) be maintained between a
wireless phone and a pacemaker to avoid potential
interference with the pacemaker. These recommendations
are consistent with the independent research and
recommendations of Wireless Technology Research. If you
have any reason to suspect that interference is taking
place, switch off your phone immediately.
Hearing aids
Some digital wireless phones may interfere with some
hearing aids. In the event of such interference, you may
wish to consult your hearing aid manufacturer to discuss
alternatives.
X200.book Page 63 Friday, October 14, 2005 10:31 AM
Potentially explosive environments
If you use any other personal medical devices, consult the
manufacturer of your device to determine if it is
adequately shielded from external RF energy.
Switch off your phone when in any area with a potentially
explosive atmosphere, and obey all signs and instructions.
Sparks in such areas could cause an explosion or fire
resulting in bodily injury or even death.
Your physician may be able to assist you in obtaining this
information.
Switch off your phone in health care facilities when
regulations posted in these areas instruct you to do so.
Vehicles
RF signals may affect improperly installed or inadequately
shielded electronic systems in motor vehicles. Check with
the manufacturer or its representative regarding your
vehicle.
You should also consult the manufacturer of any
equipment that has been added to your vehicle.
Posted facilities
Switch off your phone in any facility where posted notices
require you to do so.
Health and safety information
Other medical devices
Users are advised to switch off the phone while at a
refuelling point (service station). Users are reminded of
the need to observe restrictions on the use of radio
equipment in fuel depots (fuel storage and distribution
areas), chemical plants, or where blasting operations are
in progress.
Areas with a potentially explosive atmosphere are often
but not always clearly marked. They include the areas
below decks on boats, chemical transfer or storage
facilities, vehicles using liquefied petroleum gas, such as
propane or butane, areas where the air contains chemicals
or particles, such as grain, dust or metal powders, and any
other area where you would normally be advised to turn
off your vehicle engine.
63
X200.book Page 64 Friday, October 14, 2005 10:31 AM
Health and safety information
Emergency calls
Other important safety information
This phone, like any wireless phone, operates using radio
signals, wireless, and landline networks as well as userprogrammed functions, which cannot guarantee
connection in all conditions. Therefore, you should never
rely solely on any wireless phone for essential
communications like medical emergencies.
•
To make or receive calls, the phone must be switched on
and in a service area with adequate signal strength.
Emergency calls may not be possible on all wireless phone
networks or when certain network services and/or phone
features are in use. Check with local service providers.
•
•
•
To make an emergency call:
1. Switch on the phone.
2. Key in the emergency number for your present
location. Emergency numbers vary by location.
3. Press [ ].
Certain features like Call Barring may need to be
deactivated before you can make an emergency call.
Consult this document and your local cellular service
provider.
64
•
•
Only qualified personnel should service the phone or
install the phone in a vehicle. Faulty installation or
service may be dangerous and may invalidate any
warranty applicable to the device.
Check regularly that all wireless phone equipment in
your vehicle is mounted and operating properly.
Do not store or carry flammable liquids, gases, or
explosive materials in the same compartment as the
phone, its parts, or accessories.
For vehicles equipped with an air bag, remember that
an air bag inflates with great force. Do not place
objects, including installed or portable wireless
equipment, in the area over the air bag or in the air
bag deployment area. Improperly installed wireless
equipment could result in serious injury if the air bag
inflates.
Switch off your phone before boarding an aircraft. It is
dangerous and illegal to use wireless phones in an
aircraft because they can interfere with the operation
of the aircraft.
Failure to observe these instructions may lead to the
suspension or denial of telephone services to the
offender, or legal action, or both.
X200.book Page 65 Friday, October 14, 2005 10:31 AM
Care and maintenance
•
•
•
•
•
Keep your phone and all its parts and accessories out
of the reach of small children and pets. They may
inadvertently damage these things or choke on small
parts.
Keep the phone dry. Precipitation, humidity, and
liquids contain minerals that corrode electronic
circuits.
Do not use the phone with a wet hand. Doing so may
cause an electric shock to you or damage to the
phone.
Do not use or store the phone in dusty, dirty areas, as
its moving parts may be damaged.
Do not store the phone in hot areas. High
temperatures can shorten the life of electronic
devices, damage batteries, and warp or melt certain
plastics.
•
•
•
•
•
•
•
Do not store the phone in cold areas. When the phone
warms up to its normal operating temperature,
moisture can form inside the phone, which may
damage the phone’s electronic circuit boards.
Do not drop, knock, or shake the phone. Rough
handling can break internal circuit boards.
Do not use harsh chemicals, cleaning solvents, or
strong detergents to clean the phone. Wipe it with a
soft cloth slightly dampened in a mild soap-and-water
solution.
Do not paint the phone. Paint can clog the device’s
moving parts and prevent proper operation.
Do not put the phone in or on heating devices, such as
a microwave oven, stove, or radiator. The phone may
explode when overheated.
When the phone or battery gets wet, the label
indicating water damage inside the phone changes
colour. In this case, phone repairs are no longer
guaranteed by the manufacturer's warranty, even if
the warranty for your phone has not expired.
If your phone has a flash or light, do not use it too
close to the eyes of people or animals. This may cause
damage to their eyes.
Health and safety information
Your phone is a product of superior design and
craftsmanship and should be treated with care. The
suggestions below will help you fulfill any warranty
obligations and allow you to enjoy this product for many
years.
65
X200.book Page 66 Friday, October 14, 2005 10:31 AM
Health and safety information
•
•
66
Use only the supplied or an approved replacement
antenna. Unauthorised antennas or modified
accessories may damage the phone and violate
regulations governing radio devices.
If the phone, battery, charger, or any accessory is not
working properly, take it to your nearest qualified
service facility. The personnel there will assist you, and
if necessary, arrange for service.
X200.book Page 67 Friday, October 14, 2005 10:31 AM
Index
A
ABC mode, text input • 19
Active folder • 57
Alarm • 46
Answering
call • 23
second call • 24
Anykey answer • 57
Auto redial • 57
B
Background image • 54
Backlight time, set • 55
Band selection • 31
Barring, calls • 30
Battery
charging • 7
low indicator • 8
precautions • 61
Broadcast messages • 37
Browser, web • 42
C
Calculator • 48
Calendar • 46
Call cost • 28
Call records
dialled • 28
missed • 27
received • 28
Call time • 28
Caller ID • 31
Calls
answering • 23
barring • 30
holding • 24
redialling • 22
rejecting • 23
transferring • 25
waiting • 30
CB (Cell Broadcast) messages •
37
Characters, enter • 19
Connection tone • 33
Converter • 49
Creating messages
MMS • 39
SMS • 35
CUG (Closed User Group) • 31
D
Date, set • 47
Deleting
call records • 27
MMS • 38, 40
phonebook • 52
SMS • 34, 40
Delivery reports, message • 40
Dialled calls • 28
Dialling font, set • 55
Display
backlight, set • 55
brightness • 54
contrast • 54
icons • 10
language • 55
layout • 10
service light, set • 55
settings • 54
Diverting calls • 29
DTMF tones, send • 25
E
Emergency calls • 64
F
FDN (Fixed Dialling Number)
mode • 56
Folder tone • 33
Funbox • 42
G
Games • 44
Greeting message • 55
H
Health and safety • 60
Holding, call • 24
I
Icons, description • 10
Images, downloaded • 45
Inbox, messages
MMS • 37
SMS • 34
Infrared port • 53
International calls • 22
Internet • 42
J
Java applications • 44
67
X200.book Page 68 Friday, October 14, 2005 10:31 AM
Index
K
Keypad tones
selecting • 32
sending/muting • 25
volume • 32
L
Language, select • 55
Last number, redial • 22
Locking
menu functions • 56
phone • 56
SIM card • 56
Low battery indicator • 8
M
Memory status
downloaded items • 45
messages • 40
phonebook • 52
Message tone • 32
Messages
cell broadcast • 37
greeting • 55
MMS • 37
push • 41
SMS • 33
voice • 37
68
Minute minder • 33
Missed calls • 27
MMS messages
creating/sending • 39
deleting • 38
setting • 40
viewing • 37
Multiparty-calls • 26
Organiser • 46
Outbox, messages
MMS • 38
SMS • 34
65
display • 10
icons • 10
locking • 13, 56
password • 56
resetting • 57
switching on/off • 8
unpacking • 6
Phonebook
adding • 50
deleting • 52
finding • 50
options • 50
speed dialling • 51
PIN, change • 56
PIN2, change • 57
Power on/off tone • 33
Privacy • 56
Problems, solve • 58
Push messages • 41
P
R
N
Names
entering • 19
searching • 50
Network band, selection • 30
Network services • 29
O
Password
call barring • 30
phone • 56
Phone
care and maintenance •
Received calls • 28
Recording, voice memos • 49
Redialling
automatically • 57
manually • 22
Resetting phone • 57
Ringer
incoming calls • 32
messages • 32
Road safety • 62
Roaming • 30
S
Safety
information • 60
SDN (Service Dialling
Numbers) • 52
Security, calls • 55
Sent messages
MMS • 37, 38
SMS • 34
Service light • 55
Shortcut • 13, 57
Silent mode • 13
SIM card
inserting • 7
locking • 56
SMS messages
creating/sending • 35
deleting • 36
setting • 36
viewing • 34
X200.book Page 69 Friday, October 14, 2005 10:31 AM
Index
Sound settings • 32
Sounds, downloaded • 45
Speakerphone • 25
Speed dial • 51
Switching on/off
microphone • 25
phone • 8
T
T9 mode, text input • 20
Templates
MMS • 39
SMS • 35
Text, enter • 19
Time, set • 47
V
Voice memos • 49
Voicemail server • 37
W
Waiting call • 30
Wallpaper • 54
Web browser
access • 42
bookmarks • 43
World time • 46
69
Download PDF