Samsung | AR24HVFSEWKXMG | Samsung AR18HVFSEWKNMG User Manual

ARHVFS Series
ARHSFS Series
Air Conditioner
user & installation manual
This manual is made with 100% recycled paper.
imagine the possibilities
Thank you for purchasing this Samsung product.
DB68-05190A-02
A3050 MG Model IB&IM_DB68-05190A_HP_EN_UX.indd 1
2/17/2015 1:53:37 PM
Features of your new air conditioner
2-step cooling
2-step cooling function will quickly cool the room to reach the set temperature and then it
will adjust the fan speed and air flow direction automatically to help you stay comfortable and
refreshing.
Fast cooling/heating
If you want the strong and cool/warm air, just select Fast function! It will get you the strongest air!
Comfort cooling/heating
If you want the comfortable and refreshing air, Comfort function will spread the cool/warm air
indirectly to you, so that you can stay comfortable.
Single User
Use Single User function when you are alone at home. Single User function will minimize the
energy consumption with inverter technology and reduce your electricity bill by adjusting the
maximum operating capacity of the compressor.
Easy Filter
There is no grille to remove before separating the filter from the air conditioner! Therefore, filter can
be cleaned easily, more frequently! Frequent filter cleaning will prevent dust from entering into the
product or accumulating on the filter.
function
function will allow you to have deep, good night’s sleep by adjusting the
temperature, fan speed and air flow direction.
Smart Install
When the installation is done, your product will examine itself through trial operation to check if it
was installed properly.
Easy Installation
It’s so easy to install! You can easily hang the product on the wall and connect the pipes and wires
by opening the cover on the bottom of the product. Now you won’t have to tilt the product to
connect the pipe and the wires!
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be
disposed of with other household waste at the end of their working life. To prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they
can take these items for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract. This product and its electronic accessories should
not be mixed with other commercial wastes for disposal.
English-2
A3050 MG Model IB&IM_DB68-05190A_HP_EN_UX.indd 2
2/17/2015 1:53:37 PM
Contents
Preparation
Safety precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Checking before use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Technical specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Basic function
Checking the name of the parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Checking the remote controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Basic function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting the air flow direction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12
13
15
17
Timer
Setting the On/Off timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Options
2-Step cooling function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using the Fast function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using the Comfort function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using the Single user function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using the Quiet function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Settings
Using the Auto clean function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the Beep sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
21
22
22
23
24
25
25
Others
Cleaning the air conditioner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Maintaining the air conditioner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Installation
Safety precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Choosing the installation location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Fixing the installation plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Disassembling/Assembling the Cover panel for indoor unit installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Connecting the assembly cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Installing and connecting the assembly pipe of the indoor unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Evacuating the indoor unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Cutting or extending the pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Installing and connecting the drain hose of the indoor unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Changing direction of the drain hose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Installing and connecting the drain hose of the outdoor unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Evacuating the connected pipes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Performing the gas leak tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Fixing the indoor unit in place . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Fixing the outdoor unit in place . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Smart Install mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Final check and trial operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Pump down procedure (when removing the product) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Packing and unpacking guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
How to connect your extended power cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
English-3
A3050 MG Model IB&IM_DB68-05190A_HP_EN_UX.indd 3
2/17/2015 1:53:38 PM
Safety precautions
Before using your new air conditioner, please read this manual thoroughly to ensure
that you know how to safely and efficiently operate the extensive features and
functions of your new appliance.
Because the following operating instructions cover various models, the
characteristics of your air conditioner may differ slightly from those described in this
manual. If you have any questions, call your nearest contact center or find help and
information online at www.samsung.com.
Important safety symbols and precautions:
WARNING
CAUTION
Hazards or unsafe practices that may result in severe
personal injury or death.
Hazards or unsafe practices that may result in minor
personal injury or property damage.
Follow directions.
Cut-off the power supply.
Do NOT attempt.
Do NOT disassemble.
Make sure the machine is grounded to prevent electric shock.
FOR INSTALLATION
WARNING
Use the power line with the power specifications of the product or higher
and use the power line for this appliance only. In addition, do not use an
extension line.
 Extending the power line may result in electric shock or fire.
 Do not use an electric transformer. It may result in electric shock or fire.
 If the voltage/frequency/rated current condition is different, it may cause fire.
The installation of this appliance must be performed by a qualified
technician or service company.
 Failing to do so may result in electric shock, fire, explosion, problems with the
product, or injury and may also void warranty on the installed product.
Install a Isolation Switch next to the Air Conditioner (but not on the panels
of the Air Conditioner)and circuit breaker dedicated to the air conditioner.
 Failing to do so may result in electric shock or fire.
Fix the outdoor unit firmly so that the electric part of the outdoor unit is not
exposed.
 Failing to do so may result in electric shock, fire, explosion, problems with the
product.
English-4
A3050 MG Model IB&IM_DB68-05190A_HP_EN_UX.indd 4
2/17/2015 1:53:38 PM
FOR INSTALLATION
01 Preparation
Do not install this appliance near a heater, inflammable material. Do
not install this appliance in a humid, oily or dusty location, in a location
exposed to direct sunlight and water (rain drops). Do not install this
appliance in a location where gas may leak.
 This may result in electric shock or fire.
Never install the outdoor unit in a location such as on a high external wall
where it could fall.
 If the outdoor unit falls, it may result in injury, death or property damage.
This appliance must be properly grounded. Do not ground the appliance to a
gas pipe, plastic water pipe, or telephone line.
 Failure to do so may result in electric shock, fire, and explosion.
 Make sure to use a socket-outlet with ground.
CAUTION
Install your appliance on a level and hard floor that can support its weight.
 Failing to do so may result in abnormal vibrations, noise, or problems with the
product.
Install the draining hose properly so that water is drained correctly.
 Failing to do so may result in water overflowing and property damage. Avoid
adding drain to waste pipes as odours may arise in the future.
When installing the outdoor unit, make sure to connect the draining hose
so that draining is performed correctly.
 The water generated during the heating operation by the outdoor unit may
overflow and result in property damage.
In particular, in winter, if a block of ice falls, it may result in injury, death or
property damage.
FOR POWER SUPPLY
WARNING
When the circuit breaker is damaged, contact your nearest service center.
Do not pull or excessively bend the power line. Do not twist or tie the
power line. Do not hook the power line over a metal object, place a heavy
object on the power line, insert the power line between objects, or push
the power line into the space behind the appliance.
 This may result in electric shock or fire.
English-5
A3050 MG Model IB&IM_DB68-05190A_HP_EN_UX.indd 5
2/17/2015 1:53:38 PM
Safety precautions
FOR POWER SUPPLY
CAUTION
When not using the air conditioner for a long period of time or during a
thunder/lightning storm, cut the power at the circuit breaker.
 Failing to do so may result in electric shock or fire.
FOR USING
WARNING
If the appliance is flooded, please contact your nearest service center.
 Failing to do so may result in electric shock or fire.
If the appliance generates a strange noise, a burning smell or smoke, cutoff the power supply immediately and contact the nearest service center.
 Failing to do so may result in electric shock or fire.
In the event of a gas leak (such as propane gas, LP gas, etc.), ventilate
immediately without touching the power line. Do not touch the appliance
or power line.
 Do not use a ventilating fan.
 A spark may result in an explosion or fire.
To reinstall the air conditioner, please contact your nearest service center.
 Failing to do so may result in problems with the product, water leakage,
electric shock, or fire.
 A delivery service for the product is not provided. If you reinstall the product in
another location, additional construction expenses and an installation fee will
be charged.
 Especially, when you wish to install the product in an unusual location such as
in an industrial area or near the seaside where it is exposed to the salt in the air,
please contact your nearest service center.
Do not touch the circuit breaker with wet hands.
 This may result in electric shock.
Do not turn the air conditioner off with the circuit breaker while it is
operating.
 Turning the air conditioner off and then on again with the circuit breaker may
cause a spark and result in electric shock or fire.
After unpacking the air conditioner, keep all packaging materials well
out of the reach of children, as packaging materials can be dangerous to
children.
 If a child places a bag over its head, it may result in suffocation.
English-6
A3050 MG Model IB&IM_DB68-05190A_HP_EN_UX.indd 6
2/17/2015 1:53:39 PM
FOR USING
01 Preparation
Do not insert your fingers or foreign substances into the outlet when the air
conditioner is operating.
Take special care that children do not injure themselves by inserting their fingers into the product.
Do not touch the air flow blade with your hands or fingers during the
heating operation.
Take special care that children do not injure themselves by inserting their fingers into the product.
Do not strike or pull the air conditioner with excessive force.
This may result in fire, injury, or problems with the product.
WARNING
Do not place an object near the outdoor unit that allows children to climb
onto the machine.
This may result in children seriously injuring themselves.
Do not use this air conditioner for long periods of time in badly ventilated
locations or near infirm people.
Since this may be dangerous due to a lack of oxygen, Open a window at least once an hour. If any foreign substance such as water has entered the appliance, cut-off
the power supply and contact the nearest service center.
 Failing to do so may result in electric shock or fire.
Do not attempt to repair, disassemble, or modify the appliance yourself.
 Do not use any fuse (such as cooper, steel wire, etc.)other than the standard
fuse.
 Failing to do so may result in electric shock, fire, problems with the product, or
injury.
English-7
A3050 MG Model IB&IM_DB68-05190A_HP_EN_UX.indd 7
2/17/2015 1:53:39 PM
Safety precautions
FOR USING
CAUTION
Do not place objects or devices under the indoor unit.
 Water dripping from the indoor unit may result in fire or property damage.
(example electrical appliances)
Check that the installation frame of the outdoor unit is not broken at least
once a year.
 Failing to do so may result in injury, death or property damage.
Max current is measured according to IEC standard for safety and current is
measured according to ISO standard for energy efficiency.
Do not stand on top of the appliance or place objects (such as laundry,
lighted candles, lighted cigarettes, dishes, chemicals, metal objects, etc.) on
the appliance.
 This may result in electric shock, fire, problems with the product, or injury.
Do not operate the appliance with wet hands.
 This may result in electric shock.
Do not spray volatile material such as insecticide onto the surface of the
appliance.
 As well as being harmful to humans, it may also result in electric shock, fire or
problems with the product.
Do not drink the water from the air conditioner.
 The water may be harmful to humans.
Do not apply a strong impact to the remote controller and do not
disassemble the remote controller.
Do not touch the pipes connected with the product.
 This may result in burns or injury.
Do not use this air conditioner to preserve precision equipment, food,
animals, plants or cosmetics, or for any other unusual purposes.
 This may result in property damage.
Avoid directly exposing humans, animals or plants from the air flow from
the air conditioner for long periods of time.
 This may result in harm to humans, animals or plants.
English-8
A3050 MG Model IB&IM_DB68-05190A_HP_EN_UX.indd 8
2/17/2015 1:53:39 PM
FOR CLEANING
01 Preparation
This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the
appliance.
WARNING
Do not clean the appliance by spraying water directly onto it. Do not use
benzene, thinner or alcohol to clean the appliance.
 This may result in discoloration, deformation, damage, electric shock or fire.
Before cleaning or performing maintenance, cut-off the power supply and
wait until the fan stops.
 Failing to do so may result in electric shock or fire.
FOR CLEANING
CAUTION
Take care when cleaning the surface of the heat exchanger of the outdoor
unit since it has sharp edges.
 This should be done by a qualified technician please contact your installer or
service center.
Do not clean the inside of the air conditioner by yourself.
 For cleaning inside the appliance, contact your nearest service center.
 When cleaning the internal filter, refer to the descriptions in the ‘Cleaning the
air conditioner’ section.
 Failure to do may result in damage, electric shock or fire.
English-9
A3050 MG Model IB&IM_DB68-05190A_HP_EN_UX.indd 9
2/17/2015 1:53:39 PM
Checking before use
Operation ranges
The table below indicates the temperature and humidity ranges the air
conditioner can be operated within. Refer to the table for efficient use.
Mode
Indoor temperature Outdoor temperature
Cooling
16 ˚C~32 ˚C
Heating
27 ˚C or less
Dry
18 ˚C~32 ˚C
16 ˚C~52 ˚C
Indoor humidity
Relative humidity 80% or less
-10 ˚C~52 ˚C
-15 ˚C~24 ˚C
-
16 ˚C~52 ˚C
-
-10 ˚C~52 ˚C
Remark
ARHV
ARHS
ARHS
ARHV
ARHS
ffIf the air conditioner operates in cooling mode for long period of time in high humidity area, dew may be formed.
ffIf the outdoor temperature goes down to -5 °C, heating capacity may decrease as much as 60 %~70 % of specified
capacity according to the using conditions.
Maintaining your air conditioner
Internal protections via the unit control system
ffThis internal protection operates if an internal fault occurs in the air conditioner.
Type
Against cold air
Defrost cycle
Protect compressor
Description
The internal fan will be off to prevent cold air when the heat pump is heating.
The internal fan will be off to defrost ice when the heat pump is heating.
Vertical air flow blade will be closed during defrost cycle and it will open again during
heating operation after defrost cycle.
The air conditioner does not start operating immediately to help protect the compressor
of the outdoor unit after it has been started.
• If the heat pump is operating in Heat mode, defrost cycle is actuated to help remove frost from an outdoor unit that
may have deposited at low temperatures.
The internal fan is switched off automatically and restarted only after the defrost cycle is completed.
Smart install
ffThrough Smart install function, installer can check if the installation was done properly.
ffIf the installation was not done properly, error indicator will turn on the indoor unit display.
Therefore user will know if the installation was done properly or not.
English-10
A3050 MG Model IB&IM_DB68-05190A_HP_EN_UX.indd 10
2/17/2015 1:53:39 PM
Technical Specifications
AR18HVFSEWK/MG
AR24HVFSEWK/MG
T1
T3
T1
T3
18 000 Btu/h
14 500 Btu/h
24 000 Btu/h
21 200 Btu/h
MODEL
CLIMATE CLASS
COOLING
CAPACITY
HEATING (H1)
RATED
POWER INPUT
HEATING (H1)
EER / COP
(Btu/hr) / Watt
HEATING (H1)
230 V~ 60 Hz
6.6 A
COOLING
RATED
CURRENT
230 V~ 60 Hz
7.8 A
8.5 A
-
1520 W
1700 W
1980 W
-
11.85
8.55
12.10
-
TYPE
R-410A
1000 g [35.27 oz]
ANNUAL ENERGY CONSUMPTION
TEMPERATURE
OUTDOOR
DIMENSIONS OF THE
UNIT
1600 g [56.44 oz]
4104 kwh/yr
5346 kwh/yr
27 oC
-
29 oC
-
27 oC
-
29 oC
-
19 oC
-
19 oC
-
19 oC
-
19 oC
-
35 oC
-
46 oC
-
35 oC
-
46 oC
-
24 oC
-
24 oC
-
24 oC
-
24 oC
-
INDOOR
NET WEIGHT
14.9 kg
16.0 kg
OUTDOOR
41.7 kg
55.2 kg
INDOOR
1065 x 301 x 294 mm
1065 x 301 x 294 mm
OUTDOOR
880 x 648 x 310 mm
880 x 793 x 310 mm
COUNTRY OF ORIGIN
THAILAND
AR18HSFSEWK/MG
MODEL
CLIMATE CLASS
COOLING
CAPACITY
T3
T1
T3
18 000 Btu/h
14 500 Btu/h
22 000 Btu/h
18 000 Btu/h
HEATING (H1)
HEATING (H1)
RATED
POWER INPUT
HEATING (H1)
EER / COP
(Btu/hr) / Watt
HEATING (H1)
7.4 A
1500 W
COOLING
8.5 A
1660 W
12.00
2080 W
2260 W
8.75
11.95
8.65
3.50 W/W
TYPE
OUTDOOR
1840 W
3.95 W/W
R-410A
CHARGE
TEMPERATURE
9.5 A
10.2 A
1520 W
COOLING
INDOOR
1500 g [52.91 oz]
2300 g [81.13 oz]
4050 kwh/yr
4968 kwh/yr
27 oC
20 ˚C
29 oC
20 ˚C
27 oC
20 ˚C
29 oC
20 ˚C
19 oC
15 ˚C
19 oC
15 ˚C
19 oC
15 ˚C
19 oC
15 ˚C
35 oC
7 ˚C
46 oC
7 ˚C
35 oC
7 ˚C
46 oC
7 ˚C
24 oC
6 ˚C
24 oC
6 ˚C
24 oC
6 ˚C
24 oC
6 ˚C
INDOOR
DIMENSIONS OF THE
UNIT
7900 W
230 V~ 60 Hz
6.8 A
ANNUAL ENERGY CONSUMPTION
NET WEIGHT
6000 W
230 V~ 60 Hz
6.6 A
COOLING
RATED
CURRENT
AR24HSFSEWK/MG
T1
RATED VOLTAGE & FREQUENCY
REFRIGERANT
8.70
-
CHARGE
INDOOR
2430 W
-
COOLING
REFRIGERANT
10.7 A
-
COOLING
01 Preparation
HEATING (H1)
RATED VOLTAGE & FREQUENCY
15.5 kg
14.0 kg
OUTDOOR
52.5 kg
71.5 kg
INDOOR
1065 x 301 x 294 mm
1065 x 301 x 294 mm
OUTDOOR
880 x 793 x 310 mm
880 x 967 x 320 mm
THAILAND
CHINA
COUNTRY OF ORIGIN
English-11
A3050 MG Model IB&IM_DB68-05190A_HP_EN_UX.indd 11
2/17/2015 1:53:40 PM
Checking the name of the parts
Your air conditioner may slightly look different from illustration shown below depending on your model.
Main parts
Room temperature sensor
Air filter
Air intake
Air flow blade
(up and down)
Air flow blade
(left and right)
Display
Operation indicator
Timer/Auto clean indicator
Single user indicator
Power button/
Remote controller receiver
English-12
A3050 MG Model IB&IM_DB68-05190A_HP_EN_UX.indd 12
2/17/2015 1:53:42 PM
Checking the remote controller
• Point the remote controller towards the remote controller receiver of the indoor unit.
• When you properly press the button on the remote controller, you will hear beep sound from the indoor unit and a transmit
indicator( ) appears on the remote controller display.
02 BASIC FUNCTION
Remote controller buttons
Vertical air swing
Activate/Deactivate vertical air flow
blade movement automatically
Power
Mode
Turn on/off the air
conditioner
Temp + –

Fan
Increase/Decrease the
temperature by 1 ˚C.

Set one of the 5 operating modes
Adjust the fan speed
Single User
Options
Turn on/off the Single User function
which reduces energy usage.
Select options during operation
Timer
Select Timer option
Settings
Select settings
SET
Set/Cancel the selected option or
setting
Directional < >
Move through the Timer,
Options or Settings menu to
make a selection
• In case you wish to cancel the options or settings that you have just set, press the Options or Settings button again,
then the most recently selected item will blink and you may simply cancel it by pressing the SET button while
selected item is blinking.
English-13
A3050 MG Model IB&IM_DB68-05190A_HP_EN_UX.indd 13
2/17/2015 1:53:43 PM
Remote controller display
Transmit indicator
Operation mode
indicator
Low battery indicator
Set temperature/ Time (for
Timer option) indicator
Fan speed indicator
good'sleep indicator
Vertical air swing indicator
Options indicator
Settings indicator
•Make sure that the water does not get to the remote controller.
• The following function are displayed on the remote controller display but not supported in this model.
- Heat (ARHV)/ Virus Doctor ( ) / d'light Cool / Usage / Filter Reset / Display
• When turning off and turning on the remote controller, the Timer, Options and Settings set before turning off the
remote controller are cancelled. However, the fan direction does not change.
Low Battery warning
Inserting the batteries
When the battery is exhausted, ( ) will be displayed in the
remote controller display. When the icon appears, change
the batteries. The remote controller requires two 1.5 V AAA
type batteries.
1. Push the lever as arrow indicates on the rear side of the
remote controller and pull up.
2. Insert two AAA batteries.
Storing the remote controller
Check and match the “+” and “-” signs accordingly. Make sure
you have inserted the batteries in correct position.
3. Close the cover by place it back to its original position.
When you do not use the remote controller for long time,
remove the batteries from the remote controller and store it.
You should hear click sound when the cover is locked properly.
• T he signal may not be received properly if electronic flourescent lamps such as inverter flourescent lamps are
operating in the same space.
• If other electrical products operate by the remote controller, call your nearest contact center.
Correct disposal of batteries in this product
(Applicable in countries with separate collection systems)
This marking on the battery, manual or packaging indicates that the batteries in this product should not be disposed of with
other household waste at the end of their working life. Where marked, the chemical symbols Hg, Cd or Pb indicate that the
battery contains mercury, cadmium or lead above the reference levels in EC Directive 2006/66. If batteries are not properly
disposed of, these substances can cause harm to human health or the environment.
To protect natural resources and to promote material reuse, please separate batteries from other types of waste and recycle
them through your local, free battery return system.
English-14
A3050 MG Model IB&IM_DB68-05190A_HP_EN_UX.indd 14
2/17/2015 1:53:45 PM
Basic function
Basic operation is an operation mode that can be selected by pressing the Mode button.
Cool
In Cool mode, the air conditioner will cool your room. You can adjust the temperature and the fan speed to feel cooler in hot
season.
02 BASIC FUNCTION
Auto
In Auto mode, the air conditioner will automatically set the temperature and fan speed depending on the room
temperature.
• If current outside temperature is much higher than the selected indoor temperature, it may take time to bring the inner
temperature to the desired coolness.
• Quiet mode makes the noise quieter during the operation of the indoor unit in the Cool mode.
Dry
The air conditioner in Dry mode acts like a dehumidifier by removing moisture from the indoor air.
Dry mode makes the air feel refreshing in a humid climate.
To activate the Dry mode, set temperature on the remote controller should be lower than indoor room temperature.
Fan
Fan mode can be selected to circulate your room. Fan mode will be helpful to refresh the stale air in your room.
Heat
The air conditioner heats as well as cools. Warm your room with this versatile appliance in the cold of winter.
• Fan may not operate for about 3~5 minutes at the beginning to prevent any cold blasts while the air conditioner is
warming up.
• Quiet mode makes the noise quieter during the operation of the indoor unit in the Heat mode.
• Since the air conditioner heats the room by taking heat energy from outdoor air, the heating capacity may decrease when
outdoor temperature is extremely low.
Use an additional heating appliance in combination with the air conditioner if you feel the air conditioner heats
insufficiently.
• Only Heating models have this function:ARHSseries
English-15
A3050 MG Model IB&IM_DB68-05190A_HP_EN_UX.indd 15
2/17/2015 1:53:45 PM
Basic function
Press the
button to turn on the air conditioner.
Press the
button to set the operating mode.
• Each time you press the Mode button, the mode will change in order of Auto, Cool, Dry, Fan and Heat.
Press the
Press the
button to adjust the temperature.
Auto
You can adjust the set temperature by 1 °C within the range of 16 °C~30 °C.
Cool
You can adjust the set temperature by 1 °C within the range of 16 °C~30 °C.
Dry
You can adjust the set temperature by 1 °C within the range of 18 °C~30 °C.
Fan
Temperature adjustment is not possible.
Heat
You can adjust the set temperature by 1 °C within the range of 16 °C~30 °C.
button to set the desired fan speed.
Auto
Cool
Dry
Fan
Heat
(Auto)
(Auto),
(Low),
(Med),
(High),
(Low),
(Med),
(High),
(Turbo)
(Auto),
(Low),
(Med),
(High),
(Turbo)
(Auto)
(Turbo)
• Dry mode is only available in the cooling mode.
English-16
A3050 MG Model IB&IM_DB68-05190A_HP_EN_UX.indd 16
2/17/2015 1:53:48 PM
Adjusting the air flow direction
Vertical air flow
Press the
button to make air flow blades vertically.

To keep the air flow direction in a constant direction, press the
The air flow blade(s) will stop the movement.
button again.
02 BASIC FUNCTION
This function will allow you to adjust the air flow direction vertically.
If you adjust the vertical air flow blade manually, it may not close completely
when you turn off the air conditioner.
• A
djusting the air flow direction is not available in good'sleep mode while it is in
cool mode.
• However, you can adjust the air flow direction in good'sleep mode while it is in
heat mode.
Remote controller display
Horizontal air flow
Move the blade left or right to keep the air flow direction in a constant position you
prefer.
• T o avoid the risk of personal injuries, adjusting the horizontal air flow
direction should only be done when the unit is turned off completely.
There is a potential risk of personal injury when the unit is
mishandled.
English-17
A3050 MG Model IB&IM_DB68-05190A_HP_EN_UX.indd 17
2/17/2015 1:53:51 PM
Setting the On/Off timer
Setting the On timer
When the air conditioner is off;
1. Press the Timer button to select (On).
-- (On) indicator will keep blinking and you can set the time.
2. Press the
button to set the time.
-- You can set the time in half hour unit from 30 minutes (0.5 on the display) ~
3 hours and hour unit from 3~24 hours.
-- Time can be set from minimum 30 minutes to maximum 24 hours.
3. Press the SET button to complete the On timer setting.
-- (On) indicator and the set time of the timer will be displayed on the remote
controller display and the Timer indicator ( ) will be displayed on the indoor
unit display.
-- On timer setting will be cancelled if you don't press the SET button within
10 seconds after setting the time. Therefore, check for the (On) indicator on the
remote controller display and the Timer indicator ( ) on the indoor unit display.
Cancel
ffPress the Timer button  select (On)  press the
set the timer to
 press the SET button.
ffPress the Power ( ) button.
or
button 
Remote controller display
Additional options available in On/Off time mode (When the remote controller is on)
You can select from Auto/Cool/Dry/Fan/Heat.
You can adjust the temperature in Auto/Cool/Dry/Heat mode.
You can adjust the fan speed in Cool/Fan/Heat mode.
• When On timer setting is completed, the set status will be displayed for 3 seconds, and then only (On)
indicator will remain on the remote controller display thereafter.
• If you press the Power button on the indoor unit after setting the On timer from the remote controller,
Timer indicator on the indoor unit display will disappear and the On timer will be cancelled. Even though the
On timer is cancelled, (On) indicator on the remote controller will remain displayed.
• When the On timer is set while the air conditioner is off, Timer indicator ( ) will be displayed and remain on
until the On timer turns on.
English-18
A3050 MG Model IB&IM_DB68-05190A_HP_EN_UX.indd 18
2/17/2015 1:53:55 PM
Setting the On/Off timer
Setting the Off timer
When the air conditioner is on;
Cancel
ffPress the Timer button  select (Off)  press the
 press the SET button.
set the timer to
ffPress the Power ( ) button.
or
03 Timer
1. Press the Timer button to select (Off).
-- (Off) indicator will keep blinking and you can set the time.
button to set the time.
2. Press the
-- You can set the time in half hour unit from 30 minutes (0.5 on the display) ~
3 hours and hour unit from 3~24 hours.
-- Time can be set from minimum 30 minutes to maximum 24 hours.
3. Press the SET button to complete the Off timer setting.
-- (Off) indicator and the set time of the timer will be displayed on the remote
controller display and the Timer indicator ( ) will be displayed on the indoor
unit display.
-- Off timer setting will be cancelled if you don't press the SET button within
10 seconds after setting the time. Therefore, check for the (Off) indicator on the
remote controller display and the Timer indicator ( ) on the indoor unit display.
button 
• Off timer may not work depending on the On/Off status of the indoor
unit and the On/Off status of the indicator on the remote controller
display.
• Only the latest setting timer will be applied between the On Timer/Off
Timer and
Off timer functions.
• After setting the timer, the set time will be displayed for 3 seconds
before it disappears.
• If Timer function is used in Heating mode, Air conditioner work into
former mode. (AR✴✴HV✴✴ series)
Remote controller display
Combining On Timer and Off Timer
When the air conditioner is off
When the air conditioner is on
When set time on On timer is shorter than Off timer
When set time on On timer is longer than Off timer
Ex) On timer : 3 hours, Off timer : 5 hours
- The air conditioner will turn on after 3 hours from the
moment you have set the timer and the air conditioner will
remain on for 2 hours and then turn off automatically.
Ex) On timer : 3 hours, Off timer : 1 hour
- The air conditioner will turn off after 1 hour from the
moment you have set the timer and turn on after 2 hours
from the moment it was turned off.
• Set time for the On timer and the Off timer should be different from each other.
• When the On timer and the Off timer is set, setting can be cancelled by pressing the Power
button.
English-19
A3050 MG Model IB&IM_DB68-05190A_HP_EN_UX.indd 19
2/17/2015 1:53:57 PM
mode
2-Step cooling function
For a comfortable sleep, the air conditioner will operate in 3 stages in order of Fall asleep  Sound sleep  Wake up stage.
When the air conditioner is operating in Cool/Heat mode;
1. Press the Timer button to select ( ).
-- ( ) indicator will keep blinking and you can set the time.
2. Press the
,
button to set the time.
-- You can set the time in half hour unit from 30 minutes (0.5 on the display) ~
3 hours and hour unit from 3~12 hours.
-- Time can be set from minimum 30 minutes to maximum 12 hours.
-- Default time setting for the
mode is 8 hours.
3. Press the SET button to complete the
mode setting.
-- ( ) indicator and the set time of the
mode will be displayed on
the remote controller display.
-- Timer indicator ( ) will be displayed on the indoor unit display.
-mode setting will be cancelled if you don't press the SET button within
10 seconds after setting the time. Therefore, check for the ( ) indicator on the
remote controller display and the Timer indicator ( ) on the indoor unit display.
Cancel ffPress the Timer button  select (
set the timer to
)  press the
 press the SET button.
or
button 
Remote controller display
Additional options available in
mode
You can adjust the set temperature by 1 °C within the range of 16 °C~30 °C.
Fan speed will be adjusted automatically according to the
mode.
mode while heating operation is on, you can adjust fan speed.
However, If you select
When the
mode is on.
In Cool mode: Air flow direction will be adjusted automatically.
In Heat (ARHS) mode: Adjusting air flow direction is available.
Temperature and fan speed change in
mode
•• Fall asleep: Eases you into sleep by dropping the temperature.
•• Sound sleep: Relaxes your body and raises your temperature slightly.
•• Wake up: Allows you to wake up from comfortable intermittent air and it makes you feel refreshed.
• Recommended set temperature is between 25 °C ~ 27 °C for cooling and 21 ˚C~23 ˚C for heating.
• If the set temperature is too low, you may feel cold during sleep or catch a cold.
• Optimal operation hour of
mode is 8 hours. Therefore, if the time is set too short or long, you
may not feel as comfortable as you would expect.
• If the
mode is set over 5 hours, Wake up stage will begin when 1 hour is remaining in the
operation time and the air conditioner will stop automatically.
• When the On timer and the
function is set simultaneously, the air conditioner will only apply
the function that was set later.
English-20
A3050 MG Model IB&IM_DB68-05190A_HP_EN_UX.indd 20
2/17/2015 1:54:02 PM
2-Step cooling function
2-Step Cooling function will set the air conditioner to cool the room quickly to reach the set temperature when the indoor
temperature is higher than the set temperature, and then the air conditioner will automatically operate in Dry mode when
indoor temperature reaches set temperature.
1. Press the Options button.
2. Press the
,
or Options button until (2-Step) indicator starts to blink.
3. Press the SET button to set the 2-Step Cooling function.
04 Options
When the air conditioner is operating in Cool mode;
-- (2-Step) (2-Step) indicator will be displayed on the remote controller display
and 2-Step Cooling function will begin.
Cancel
ffPress the Options button  Press the
,
or Options button to
make the (2-Step) indicator blink and press the SET button.
Remote controller display
English-21
A3050 MG Model IB&IM_DB68-05190A_HP_EN_UX.indd 21
2/17/2015 1:54:05 PM
Using the Fast function
You can set the Fast function to provide fast and powerful cooling/heating.
When the air conditioner is operating in Cool/Heat mode;
1. Press the Options button.
2. Press the
,
or Options button until (Fast) indicator starts to blink.
3. Press the SET button to set the Fast function.
-- (Fast) (Fast) indicator will be displayed on the remote controller display and
Fast function will begin.
Cancel
ffPress the Options button Press the
,
or Options button to
make the (Fast) indicator blink and press the SET button.
• Fast function is only available in Cool/Heat mode.
• Vertical air swing can be adjusted.
• Set temperature and fan speed cannot be adjusted.
• If the Fast function is selected while 2-Step Cooling/Comfort/Single
function is on, corresponding function will be
user/Quiet/
cancelled.
• When you select Fast function in Heat mode, you may not be able to
increase fan speed in order to prevent any cool air from blowing.
Remote controller display
Using the Comfort function
You can set the Comfort function to provide mild cooling/heating.
When the air conditioner is operating in Cool/Heat mode;
1. Press the Options button.
2. Press the
,
or Options button until (Comfort) indicator starts to blink.
3. Press the SET button to set the Comfort function.
-- (Comfort) (Comfort) indicator will be displayed on the remote controller
display and Comfort function will begin.
Cancel
ffPress the Options button  Press the
,
or Options button to
make the (Comfort) indicator blink and press the SET button.
• Comfort function is only available in Cool/Heat mode.
• Vertical air swing can be adjusted.
• Set temperature can be adjusted, but fan speed cannot be adjusted.
• If the Comfort function is selected while 2-Step Cooling/ Fast / Single
user / Quiet /
function is on, corresponding function will be
cancelled.
Remote controller display
A3050 MG Model IB&IM_DB68-05190A_HP_EN_UX.indd 22
English-22
2/17/2015 1:54:09 PM
Using the Single user function
This function will reduce the energy usage while the air conditioner is operating in Cool/Heat mode.
When the air conditioner is operating in Cool/Heat mode;
-- (Single user) indicator will be displayed on the remote controller display. Then
will be displayed on the set temperature indicator part for few
seconds and Single user function will begin.
-- When the Single user function is on, vertical air swing will turn on automatically.
-- If the current set temperature is lower than 24°C in Cool mode, it will be
automatically raised to 24 °C.
04 Options
1. Press the Single user button.
Cancel ffPress the Single user button once again.
• Single user function is only available in Cool/Heat mode.
• If the Single user function is selected while 2-Step Cooling/Fast/Comfort
/Quiet/
function is on, corresponding function will be
cancelled.
• Vertical air swing will remain on even after the Single user function
is cancelled.
• Select or cancel the Single User function with the Options button.
-- Press the Options button  press the ,
or Options button to
make (Single user) indicator blink and press the SET button.
Remote controller display
Additional options available in Single user function
You can adjust the set temperature by 1 °C within the range of 24 °C ~ 30 °C in Cool mode.
and 16 °C ~ 30 °C in Heat mode.
(Auto),
(Low),
(Med),
(High),
(Turbo) can be selected.
Vertical air swing can be selected.
English-23
A3050 MG Model IB&IM_DB68-05190A_HP_EN_UX.indd 23
2/17/2015 1:54:11 PM
Using the Quiet function
You can reduce the noise generated from an indoor unit during Cool/Heat mode.
When the air conditioner is operating in Cool/Heat mode;
1. Press the Options button.
2. Press the
,
or Options button until (Quiet) indicator starts to blink.
3. Press the SET button to set the Quiet function.
-- (Quiet)(Quiet) indicator will be displayed on the remote controller display and
Quiet function will begin.
Cancel
ffPress the Options button  Press the
,
or Options button to
make the (Quiet) indicator blink and press the SET button.
Additional options available in Quiet function
You can adjust the set temperature by 1 °C within the range of
16 °C ~ 30 °C.
Fan speed is set to
(Auto).
Vertical air swing can be selected.
Remote controller display
• Quiet function is only available in Cool/Heat mode.
• If the Quiet function is selected while 2-Step Cooling/Fast /Comfort/
function is on, corresponding function will
Single user/
be cancelled.
English-24
A3050 MG Model IB&IM_DB68-05190A_HP_EN_UX.indd 24
2/17/2015 1:54:15 PM
Using the Auto clean function
Auto clean function will minimise the moisture inside of the indoor unit. Activate this function to help provide you with
clean air.
When the air conditioner is operating;
Cancel
05 Settings
1. Press the Settings button.
2. Press the
,
or Settings button until (Clean) indicator starts to blink.
3. Press the SET button to set the Auto clean function.
-- 3 seconds after setting Auto clean function, (Clean) indicator on the remote
controller display will disappear and Timer indicator ( ) will turn on the indoor
unit display. Auto clean function will be activated after the air conditioner stops
operating.
-- Duration of the Auto clean function can be different depending on the previous
operation mode used.
Auto(cool), Cool, Dry mode : 30 minutes.
Auto(heat), Heat, Fan mode :15 minutes.
ffPress the Settings button  Press the
,
or Settings button to
make the (Clean) indicator blink and press the SET button.
• When the operation mode is set during Auto clean function is activated,
the air conditioner will operate in chosen operation mode and the Auto
clean function will be re-activated when the operation stops.
• During the auto clean function, indoor fan will continue to run and air
flow blade will remain open to expel ambient air.
• lighting in Auto clean mode.
Indoor unit display
Setting the Beep sound
Beep sound from the indoor unit can be muted.
1. Press the Settings button.
2. Press the
,
or Settings button until (Beep) indicator starts to blink.
3. Press the SET button to mute the beep sound.
-- 3 seconds after setting Beep sound function, (Beep) indicator on the remote
controller display will disappear and Beep sound function will begin.
English-25
A3050 MG Model IB&IM_DB68-05190A_HP_EN_UX.indd 25
2/17/2015 1:54:20 PM
Cleaning the air conditioner
CAUTION
•Make sure to turn off the power of the indoor unit and cut-off
the power supply before cleaning the air conditioner.
Cleaning the indoor unit

Clean the product with a tepid damp cloth.

Remove the dust accumulated in the gap of the product with a soft
brush.
• C
ontact the service center when you clean the indoor unit
heat exchanger because it needs to be disassembled.
•Do not clean the display using alkaline detergent.
CAUTION •Do not use sulfuric acid, hydrochloric acid, organic solvents
(such as thinner, kerosene and acetone etc.) to clean the
surface of the product or put any stickers on it.
They may damage the surface of the air conditioner.
Cleaning the outdoor unit heat exchanger
ffWhen dust accumulates on the heat exchanger, it may decrease
cooling performance. Therefore, clean it regularly.
ffSpray water to clean the dust.
• If it is difficult to clean the outdoor unit heat exchanger on
your own, contact service center.
•Be careful with the sharp edges on the
CAUTION outdoor unit heat exchanger.
Heat exchanger
(Illustration may differ slightly
depending on the models)
English-26
A3050 MG Model IB&IM_DB68-05190A_HP_EN_UX.indd 26
2/17/2015 1:54:21 PM
Cleaning the air conditioner
Air filter
Removing the Air filter
06 Others
There is a hole on the bottom right side of the filter. Put your
finger in that hole to get a grip on the filter and slightly push
it up to release the hooks from the bottom side. Then, pull it
down to remove the filter from the main body.
Cleaning the air filter
Washable foam based air filter captures large particles from the air. The filter is cleaned with a vacuum or by hand washing.
Remove the Air filter from the main body.
Clean the Air filter with a vacuum cleaner or soft brush.
If dust is too heavy, rinse it with running water.
Insert the Air filter back in its original position.
Dry the Air filter in a ventilated area.
• C
lean the Air filter every 2 weeks. Cleaning term may differ depending on the usage and environmental
conditions. In dusty area, clean it once a week.
• If the Air filter dries in a confined (or humid) area, odors may generate. If it occurs, re-clean and dry it in a
well-ventilated area.
English-27
A3050 MG Model IB&IM_DB68-05190A_HP_EN_UX.indd 27
2/17/2015 1:54:23 PM
Cleaning the air conditioner
Reassembling the Air filter
1. Put the filter on the main body and insert the hooks which are
in the top of the Air filter into the main body. ➀
Air filter
2. There’s one hook in both side of the filter, press the surface of
the Air filter softly and get the hooks into the main body. ➁
3. Press the bottom of the filter lightly to securely fix the main
body. ➂ ➃ ➄
English-28
A3050 MG Model IB&IM_DB68-05190A_HP_EN_UX.indd 28
2/17/2015 1:54:24 PM
Maintaining the air conditioner
If the air conditioner will not be used for an extended period of time, dry the air conditioner to maintain it in best condition.
06 Others
1.Dry the air conditioner thoroughly by operating in Fan mode for 3 to 4 hours
and cut-off the power supply. There may be internal damage if moisture is left
in components.
2.Before using the air conditioner again, dry the inner components of the air
conditioner again by running in Fan mode for 3 to 4 hours. This helps remove
odors which may have generated from dampness.
Periodical checks
Refer to the following chart to maintain the air conditioner properly.
Type
Every 2
weeks
Description
Clean the air filter (1)
Indoor
unit
Every 3
months
Every 4
months

Clean the condensate drain pan (2)

Thoroughly clean the heat exchanger (2)

Clean the cross fan (2)

Clean the condensate drain pipe (2)

Replace the remote controller batteries (1)

Clean the heat exchanger on the outside of the unit (2)
Outdoor
unit
Once a year

Clean the heat exchanger on the inside of the unit (2)

Clean the electric components with jets of air (2)

Verify that all the electric components are firmly
tightened (2)

Clean the fan (2)

Verify that all the fan assembly is firmly tightened (2)

Clean the condensate drain pan (2)

 : This check mark requires checking the indoor/outdoor unit periodically.
Follow the description to maintain the air conditioner properly.
(1) The described operations should be performed more frequently if
the area of installation is very dusty.
CAUTION
(2) These operations must always be performed by qualified personnel.
For more detailed information, see the installation part in the
manual.
English-29
A3050 MG Model IB&IM_DB68-05190A_HP_EN_UX.indd 29
2/17/2015 1:54:24 PM
Troubleshooting
Refer to the following chart if the air conditioner operates abnormally. This may save
time and unnecessary expenses.
PROBLEM
The air conditioner
does not work at
all.
The temperature
adjustment is not
working.
Cool/Warm air
does not come
out of the air
conditioner.
SOLUTION
• Check power status and then operate the air conditioner
again.
• Plug in or switch on the circuit breaker and then operate
the air conditioner again.
• Ensure Isolator is switch on.
• Check if you have set the Off Timer. Operate the air
conditioner again by pressing the Power button.
• Check if you have selected Fan/Fast mode. In these modes,
set temperature is set to auto and you cannot adjust the
temperature.
• Check if the set temperature is higher(during Cool mode)/
lower(during Heat mode) than the current temperature.
Press the Temp + or - button on the remote controller to
change the set temperature.
• Check if the Air filter is blocked by dirt. If there is a lot of
dust on the Air filter, cooling(heating) performance may
decrease. Clean them frequently.
• Check if the outdoor unit is covered or installed near the
obstacle. Take the cover off and take the obstacle away.
• Check if the air conditioner is operating in defrost mode.
When the ice formed in winter or the outdoor temperature
is too low, the air conditioner operates in defrost mode
automatically. In defrost mode, indoor fan stops and warm
air does not come out.
• If the doors or windows are open, it may cause bad cooling
(heating) performance. Close the doors and windows.
• Check if the air conditioner has just been turned on after
stopping cooling or heating operation. In this case, just a
fan will run to protect the outdoor unit compressor.
• Check if the pipe length is too long. When the pipe
length exceeds maximum allowable pipe length, cooling
(heating) performance may decrease.
English-30
A3050 MG Model IB&IM_DB68-05190A_HP_EN_UX.indd 30
2/17/2015 1:54:24 PM
Troubleshooting
SOLUTION
mode. In cool mode,
• Check if you have selected
you cannot adjust the air flow direction. (If the
mode is operating in Heat mode, you can adjust the air
flow direction.)
Fan speed
• Check if you have selected Auto/Dry/Fast/Comfort/
adjustment is not
mode. In these mode, fan speed is set to Auto
working.
and you cannot adjust the fan speed.
Remote controller • Check if your batteries are depleted.
is not working.
• Make sure nothing is blocking your remote controller
sensor.
• Check that there are strong lighting apparatus near the air
conditioner. Strong light which comes from fluorescent
bulbs or neon signs may interrupt the electric waves.
Timer function
• Check if you press the SET button on the remote
does not set.
controller after you have set the time.
The indicator
• Press the Power button or disconnect the power plug/
is blinking
switch off the auxiliary power switch.
continuously.
If the indicator is still blinking, contact the service center.
Odors permeate in • Check if the appliance is running in a smoky area.
the room during
Ventilate the room or operate the air conditioner in Fan
operation.
mode for 1~2 hours. (We do not use smelly components
in the air conditioner.)
• Check the Drains have been cleared Regular Maintenance.
Error is indicated.
• When an indoor unit indicator blinks, contact the nearest
service center. Please ensure the error code is passed onto
the service center when booking the service call.
Noise is generated. • Depending on the status of the air conditioner usage,
noise can be heard when refrigerant flow movement
changes. It is normal.
Smoke is
• If may not be a fire but it can be a steam generated by the
generated from
defrost operation from outdoor heat exchanger during
the outdoor unit.
Heat mode in winter.
Water is dropping • Water may be generated because of the temperature
from the outdoor
difference. It is normal.
unit piping
connection.
06 Others
PROBLEM
Air flow
adjustment is not
working.
English-31
A3050 MG Model IB&IM_DB68-05190A_HP_EN_UX.indd 31
2/17/2015 1:54:24 PM
Safety precautions
Carefully follow the precautions listed below because they are essential to guarantee the safety of the equipment.
• Always disconnect the air conditioner from the power supply before servicing it or accessing its internal components.
• Verify that installation and testing operations are performed by qualified personnel.
• Verify that the air conditioner is not installed in an easily accessible area.
General information
 Carefully read the content of this manual before installing the air conditioner and store the manual in a safe place in order
to be able to use it as reference after installation.
For maximum safety, installers should always carefully read the following warnings.
Store the operation and installation manual in a safe location and remember to hand it over to the new owner if the air
conditioner is sold or transferred.
This manual explains how to install an indoor unit with a split system with two SAMSUNG units.
The use of other types of units with different control systems may damage the units and invalidate the warranty.
The manufacturer shall not be responsible for damages arising from the use of non compliant units.
This product has been determined to be in compliance with the Low Voltage Directive (2006/95/EC), and the
Electromagnetic Compatibility Directive (2004/108/EC) of the European Union.
The manufacturer shall not be responsible for damage originating from unauthorized changes or the improper connection
of electric and requirements set forth in the “Operating limits” table, included in the manual, shall immediately invalidate
the warranty.

T he air conditioner should be used only for the applications for which it has been designed: the indoor unit is not suitable
to be installed in areas used for laundry.
Do not use the units if damaged. If problems occur, switch the unit off and disconnect it from the power supply.
In order to help prevent electric shocks, fires or injuries, always stop the unit, disable the protection switch and contact
SAMSUNG’s technical support if the unit produces smoke, if the power cable is hot or damaged or if the unit is very noisy.
Always remember to inspect the unit, electric connections, refrigerant tubes and protections regularly. These operations
should be performed by qualified personnel only.
The unit contains moving parts, which should always be kept out of the reach of children.
Do not attempt to repair, move, alter or reinstall the unit. If performed by unauthorized personnel, these operations may
cause electric shocks or fires.
Do not place containers with liquids or other objects on the unit.
All the materials used for the manufacture and packaging of the air conditioner are recyclable.
The packing material and exhaust batteries of the remote controller(optional) must be disposed of in accordance with
current laws.
The air conditioner contains a refrigerant that has to be disposed of as special waste. At the end of its life cycle, the air
conditioner must be disposed of in authorized centers or returned to the retailer so that it can be disposed of correctly and
safely.
Installing the unit
IMPORTANT: When installing the unit, always remember to connect first the refrigerant tubes, then the electrical lines.
Always disassemble the electric lines before the refrigerant tubes.
 Upon receipt, inspect the product to verify that it has not been damaged during transport.
If the product appears damaged, DO NOT INSTALL it and immediately report the damage to the carrier or retailer (if the
installer or the authorized technician has collected the material from the retailer.)
English-32
A3050 MG Model IB&IM_DB68-05190A_HP_EN_UX.indd 32
2/17/2015 1:54:24 PM
 After completing the installation, always carry out a functional test and provide the instructions on how to operate the air
conditioner to the user.
 Do not use the air conditioner in environments with hazardous substances or close to equipment that release free flames to

The air conditioner should be used only for the applications for which it has been designed : the indoor unit is not suitable
to be installed in areas used for laundry.

Our units must be installed in compliance with the spaces indicated in the installation manual to ensure either accessibility
from both sides or ability to perform routine maintenance and repairs. The units’ components must be accessible and that
can be disassembled in conditions of complete safety either for people or things.
For this reason, where it is not observed as indicated into the Installation Manual, the cost necessary to reach and repair the
unit (in safety, as required by current regulations in force) with slings, trucks, scaffolding or any other means of elevation
won’t be considered in-warranty and charged to end user.
07 INSTALLATION
avoid the occurrence of fires, explosions or injuries.
 To help prevent injury when accidentally touching the indoor unit fan, install the indoor unit at least 2.5 m above the floor.
Power supply line, fuse or circuit breaker
 Always make sure that the power supply is compliant with current safety standards. Always install the air conditioner in
compliance with current local safety standards.
 Always verify that a suitable grounding connection is available.

Verify that the voltage and frequency of the power supply comply with the specifications and that the installed power is
sufficient to ensure the operation of any other domestic appliance connected to the same electric lines.

Always verify that the cut-off and protection switches are suitably dimensioned.

Verify that the air conditioner is connected to the power supply in accordance with the instructions provided in the wiring
diagram included in the manual.

Always verify that electric connections (cable entry, section of leads, protections…) are compliant with the electric
specifications and with the instructions provided in the wiring scheme.
Always verify that all connections comply with the standards applicable to the installation of air conditioners.
Choosing the installation location
Indoor unit










For Wi-Fi Air-conditioner installation, select indoor unit location near to wireless router.
In case Wi-Fi signal strength weakened , Smart APP may be disconnected depending on the Wi-Fi signal strength.
Where airflow is not blocked.
Where cool air can be distributed throughout the room.
Install the refrigerant piping length and the height difference of both indoor and outdoor units as indicated in the
installation diagram.
Wall that prevents vibration and is strong enough to hold the product weight.
Out of the direct sunlight .
1 m or more away from the TV or radio (to prevent the screen from being distorted or noise from being generated).
As far away as possible from the fluorescent and incandescent lights (so that the remote controller can be operated well).
A place where the air filter can be replaced easily.
Don't install directly above electronics equipment as leaking water may cause damage if not serviced. (eg. Computers, TV, etc).
English-33
A3050 MG Model IB&IM_DB68-05190A_HP_EN_UX.indd 33
2/17/2015 1:54:24 PM
Choosing the installation location
Outdoor Unit

Where it is not exposed to strong wind
Well ventilated and dustless places
 Where possible keep out of sunlight and rain
 Where neighbors are not annoyed by operation sound or hot air
 Solid wall or support that prevents vibration and is strong enough to hold the product weight
 Where there is no risk of flammable gas leakage
 When installing the unit at a high place be sure to fix the unit legs
 3 m or more away from the TV or radio (to prevent the screen from being distorted or noise from being generated)
 Install the unit horizontally
 Place where drained water does not become any problem.
 Place with no plants (especially climbing plants) and where small animal can not access.
 Outdoor unit should not be place higher than 2.4 m or directly under eaves for accessibility for service and OH&S reasons.

• Avoid the following places to prevent malfunction of the unit
- Where there is machine oil
- Salty environment such as seaside areas
- Where sulfide gas exists
- Other special atmosphere areas
100 mm or more
Outdoor
Unit
Outer wall
125 mm or
more
125 mm
or more
A
Indoor
Unit
You can select the direction of
draining (left or right).
Cut insulation to
have rainwater
drained
Wrap the refrigerant pipes and the
drain hose with the absorbent pad
and vinyl tape. Refer to page 52 for
further details.
Make an U-trap(A) on the
pipe (which is connected
to the indoor unit) at
outer wall and cut the
bottom part of the
insulation (about 10 mm)
to prevent rainwater from
getting inside through
the insulation. However,
be careful not to damage
the pipe.
'L' m as maximum pipe length
and 3 m as minimum pipe length.
(It will reduce noise and vibration)
'H' meters
maximum
total pipe
height
'L' meters maximum total pipe
length
Pipe Length
Pipe Height
Minimum Maximum Maximum
3
15
8
09/12
3
30
15
18/24
Model
Make at least one round: It will help reduce noise and vibration.
 The appearance of the unit may be different from the diagram depending on the model.
English-34
A3050 MG Model IB&IM_DB68-05190A_HP_EN_UX.indd 34
2/17/2015 1:54:26 PM
Space Requirements for Outdoor Unit
When installing 1 outdoor unit
07 INSTALLATION
 Figure Description
Top view
Side view
Air intake
Air outlet
Air intake
Air outlet

,
Air flow direction.
(Unit : mm)
1500 or more
 When 3 sides of the outdoor unit
are blocked by the wall
300 or more
 When the air outlet is towards the
wall
300 or more
 When the air outlet is opposite
the wall
150 or more
 The upper part of the outdoor
unit and the air outlet is opposite
the wall
 When the walls are blocking front
and the rear side of the outdoor
unit
300 or
more
300 or more
1500 or
more
500 or more
2000 or more
1500 or more
 The upper part of the outdoor unit
and the air outlet is towards the wall
600 or more
When installing more than 1 outdoor unit
(Unit : mm)
300 or more
 When 3 sides of the outdoor unit are blocked by the wall
1500 or more
 When the air outlet is towards the wall
300 or more
600 or more
600 or more
600 or more
English-35
A3050 MG Model IB&IM_DB68-05190A_HP_EN_UX.indd 35
2/17/2015 1:54:27 PM
Choosing the installation location
500 or more
300 or more
500 or more
600 or more
1500 or
more
600 or more
(Unit : mm)
 When the upper part of the outdoor unit and
the air outlet is opposite the wall
300 or
more
 When the walls are blocking front and the rear side of the outdoor
units
300 or more
 When front and rear side of the outdoor unit is towards the wall
1500 or
more
600 or
more
3000 or
more
3000 or
more
200 or
more
• If installation is done in inappropriate space, unit may generate sound and cause bad effect on the product.
• Installation must be done in level and in a place where vibration will not cause any effect.
Accessories
The following accessories are supplied with the air conditioner:
• The number of each accessory is indicated in parentheses.
Accessories in the indoor unit case
Installation Plate (1)
Remote controller (1)
Batteries for Remote
controller (2)
M4 x 16 Tapped
Screws (2)
24HS
M4 x 12 Tapped Screws (2)
18/24HV
18HS
Cap Screws (2)
User’s & Installation
Manual (1)
Remote Control
Holder (1)
Accessories in the outdoor unit case
Drain Plug (1)
ARHS
Rubber Leg (4)
English-36
A3050 MG Model IB&IM_DB68-05190A_HP_EN_UX.indd 36
2/17/2015 1:54:30 PM
Accessories
Optional accessories
The following connection accessories are optional. If they are not supplied, you should obtain them before installing the air
conditioner.
Insulated
Assembly Pipe,
Ø6.35mm x 5 m (1)
Insulated Assembly Pipe, Insulated Assembly Pipe, Insulated Assembly Pipe,
PE T3 Foam Tube
Ø9.52mm x 5 m (1)
Ø12.70mm x 5 m (1)
Ø15.88 mm x 5 m (1)
Insulation (1)
09/12
18
24
Pipe Clamps A (3)
Pipe Clamps B (3)
3-wire
Assembly Cable (1)
2-wire
Assembly Cable (1)
Cement Nails (6)
M4 x 25 Tapped
Screws (6)
Drain Hose,
length 2m (1)
Vinyl Tapes (2)
07 INSTALLATION
• T he flare nuts are attached to the end of each pipe of an evaporator or a service port.
Use the nuts when connecting the pipes.
• The assembly cable is optional. If it is not supplied, use the standard cable.
• The drain plug and rubber leg are only included when the air conditioner is supplied without the assembly
pipe as seen in the picture below.
Putty 100g (1)
Drain Plug (1)
• If these accessories are supplied, they will be in the accessory box.
Tools required for installation
General Tools
• Vacuum Pump(Backward flowing prevention)
• Torque Wrench
• Pipe Cutter
• Reamer
• Screw Driver
• Spanner
• Drill
• Manifold Gauge
• Pipe Bender
• L Wrench
• Stud Finder
• Spirit Level
• Measuring Tape
Tools for test operations
• Thermometer
• Resistance Meter • Electroscope
English-37
A3050 MG Model IB&IM_DB68-05190A_HP_EN_UX.indd 37
2/17/2015 1:54:32 PM
Fixing the installation plate
You can select the direction of the drain hose depending on where you want to install the indoor unit. Therefore before fixing the
installation plate to a wall or a window frame, you must determine the position of the 65 mm hole through which the cable, pipe and
hose pass to connect the indoor unit to the outdoor unit.
When facing the wall, the pipe and cable can be connected from the:
 Direction of pipe
• Right (A)
• Left (B)
• Underside_right (C)
• Rear_right or left (D)
B
A
D
D
C
• You can install the refrigerant pipe in the left/right/bottom, or the rear side of the indoor unit.
• If changing the pipe direction from left to right, do not drastically bent it but slowly turn it in the opposite direction
as shown. Otherwise, the pipe may be damaged in the process.
1. Disassemble the cover panel as described in page 39~40.
2. Remove the Hanger plate from the indoor unit.
(1) Unscrew 2 screws that fixes the Hanger plate to the indoor unit.
(2) Push the hooks (on the bottom part of the indoor unit) up to release the installation plate from the hooks that holds it.
(3) Pull the installation plate to release it completely from the indoor unit.
Screw
Screw(M4x10)
3. Determine the position of the pipe and drain hose hole as seen in the picture and drill the hole with an inner diameter of
65 mm so that it slants slightly downwards.
D
A
Pipe hole (Ø65 mm)
B
C
(Unit : mm)
Model
A
B
C
D
18/24
33
110
110
33
• M
ake sure to drill only one hole after choosing the
direction of the pipe.
4. Fix the indoor unit.
If you fix the indoor unit on a wall
(1) Fix the installation plate to the wall giving attention to the weight of the indoor unit.
• If you mount the plate to a concrete wall using plastic anchors, make sure that gaps
between the wall and the plate, created by projected anchor, is less than 20 mm.
Plastic
Anchor
<20 mm
Wall
If you fix the indoor unit on a window frame
(1) D
etermine the positions of the wooden uprights to be attached to the window frame.
(2) A
ttach the wooden uprights to the window frame giving attention to the weight of the indoor unit.
(3) A
ttach the installation plate to the wooden upright using tapping screws.
If you fix the indoor unit on a gypsum board
(1) U
se stud finder to find out locations of the studs.
(2) Fix the plate hanger on two studs.
English-38
A3050 MG Model IB&IM_DB68-05190A_HP_EN_UX.indd 38
2/17/2015 1:54:35 PM
• S earch for other spots if there are less than two studs, or the distance between the studs are different from the
plate hanger.
• Fix the installation plate without inclining to one side.
07 INSTALLATION
• M
ake sure that a wall can withstand the weight of the product. If you install the product in a place where it is not
strong enough to withstand the product weight, the unit could fall and cause injury.
Assembling the hanger screw
Use 2 screws to fix the indoor unit with hanger plate as shown in the picture.
Screw(M4x10)
Screw
Disassembling/Assembling the Cover panel for indoor unit installation
Please scan
this QR code for detail
video of indoor unit
installation.
In order to install the indoor unit, you must disassemble the cover panel first. Please proceed following
instructions to disassemble and assemble the cover panel. Hooks (on the cover panel) may get damaged if you
apply excessive force as you disassemble and assemble the cover panel. Please follow the following instructions.
Removing the screws
Cover panel is assembled on the bottom part of the indoor unit (as shown in the illustration) and it is fastened
with screws. Remove the Cap screw first and unfasten the screws so that you can disassemble the cover panel.
Cap Screw
<Remove the Cap screw>
Cover Panel
<Unfasten the screw>
English-39
A3050 MG Model IB&IM_DB68-05190A_HP_EN_UX.indd 39
2/17/2015 1:54:37 PM
Disassembling/Assembling the Cover panel for indoor unit installation
Removing the Cover panel (Before mounting the indoor unit)
The bottom panel fits the main body using the side, center, and bottom hooks as shown. Unlock the side hooks
first, and then unlock the center and bottom hooks.
Check the location of the hooks before removing the cover panel.
ffLocation of the hooks on the central part
Number and location of the hooks
Side
hooks
Center hook
Center
hooks
Bottom hooks
Bottom hook
 For specific Hook location and quantity, please
refer to cover panel with indicating arrows based
on physical goods.
ffRemoving the hooks on the side
ffRemoving the hooks on the central part
①
②
①
 Caution (fragile)
-- Gently press the both side of the cover
panel inwards (①) and release the hooks
on both sides(②).
 Caution (fragile)
-- Use both hands
-- Release each hook by pushing it up at an angle.
Assembling the Cover panel (After mounting the indoor unit)
To assemble the Cover panel, proceed in reverse order of disassembling.
Use both hands for assembling and be extra careful not to damage the pipes and drain hose.
Lock the side, center, and bottom hooks in this sequence. Tighten the bottom panel with the screws, and close
the screw holes with their cap.
<Lock the side hook>
<Lock the bottom hook>
<Fasten the screw>
<Assemble the Cap screw>
English-40
A3050 MG Model IB&IM_DB68-05190A_HP_EN_UX.indd 40
2/17/2015 1:54:49 PM
Connecting the assembly cable
Cable specification
Power cable
Interconnection cable
18/24
3G x 2.5 mm², H07RN-F
3G x 1.0 mm², H07RN-F
2 x 0.75 mm², H05RN-F
Type GL
25 A
• C
onnect the power cable to the auxiliary circuit breaker. If every pole fails to connect to the power supply, it must be
incorporated in a wire with a contact opening of ≥3 mm.
• Use shield cable (Category 5; less than 50pF/m) for noisy environmental site.
• Power supply cords of parts of appliances for outdoor use shall not be lighter than polychloroprene sheathed
flexible cord. (Code designation IEC: 60245 IEC66 / CENELEC: H07RN-F, IEC: 60245 IEC57 / CENELEC:H05RN-F)
07 INSTALLATION
Model
Connecting the cable
Electrical work
(1) For electrical and earth works, comply with the ‘technical standards of electrical installations’ and the the ‘wiring
regulations’ of the Local wiring regulations.
(2) Tighten the terminal block screw to 1.2~1.8 N•m (12~18 kgf•cm).
(3) Precautions when connecting terminal blocks of the indoor unit
 Before connecting, make sure the connecting part of the terminal socket is facing upwards.
Upside down

The terminal
socketis damaged.
There is no ring terminalto
cover the wire.
There must be no space between the terminal and the screw when connected.
- Any remaining space may become a fire hazard due to overheating of the electrical contact.
The terminal socket
is upside down.
Either the screw is not fitted
properly or there is a space
between the screw and the
ring terminal.
• F or the terminal block wiring, use a wire with a ring terminal socket only.
Regular wires without a ring terminal socket may become a fire hazard due to overheating of the electrical
contact during a wiring work.
 When you install the unit, make first refrigerant connections and then electrical connections.
Connect the air conditioner to grounding system before performing the electrical connection.
If unit is uninstalled, first disconnect electrical cables, then refrigerant connections.
If the outdoor unit is more than 5.5 meters away from the indoor unit, you must extend the cable. The maximum length of the
cable is 15(09/12) / 20(18/24) meters.
1. Extend the assembly cable if necessary.
• Do not connect two or more different cables to extend the length. It may cause fire.
English-41
A3050 MG Model IB&IM_DB68-05190A_HP_EN_UX.indd 41
2/17/2015 1:54:49 PM
Connecting the assembly cable
2 . Open the cover panel.
3 . Remove the screw securing the connector cover.
4 . Pass the assembly cable through the rear of the indoor unit and connect the assembly cable to terminals.
(Refer to the picture below)
• Each wire is labeled with the corresponding terminal number.
5 .
6 .
7 .
8 .
9.
Pass the other end of the cable through the 65 mm hole in the wall.
Close the connector cover by tightening the screw carefully.
Close the cover panel.
Remove the terminal board cover on the side of the outdoor unit.
Connect the cables to the terminals as seen in the picture.
• Each wire is labeled with the corresponding terminal number.
18/24HV
18HS
Indoor unit
Indoor unit
24HS
1(L)
1(L) 2(N)
2(N) F1F1 F2F2
1(L) 2(N)
1(L) 2(N)
F1
F1
Indoor unit
F2
F2
1(L) 2(N) F1
F2
1(L) 2(N) F1
F2
Outdoor unit
Outdoor unit
LL
NN
F1
Outdoor unit
F2
F1
1(L) 2(N) L
N
F1
F2
F2
• Also circular terminal must be matched with screw size in terminal block.
• After connecting the cables, make sure terminal numbers on the indoor/outdoor unit matches.
• Please ensure that Power & Communication cables are separated, they must not be in the same cable.
10. Connect the grounding conductor to the grounding terminals.
11. Close the terminal board cover by tightening the screw carefully.
• C
onnect the wires firmly so that wires can not be pulled out easily.
(If they are loose, it could cause burn-out of the wires.)
• Connect the wires according to color codes, referring to the wiring diagram.
• The power cable and the interconnection cable should be selected according to the specification in page 41.
English-42
A3050 MG Model IB&IM_DB68-05190A_HP_EN_UX.indd 42
2/17/2015 1:54:51 PM
Installing and connecting the assembly pipe of the indoor unit
There are 2 refrigerant pipes of different diameters:
• The smaller one is for the liquid refrigerant
• The larger one is for the gas refrigerant
A short pipe is already fitted to the air conditioner. You may
need to extend the pipe using the assembly pipe (optional).
The connection procedure for the refrigerant pipe varies
according to the exit position of the pipe when facing the wall:
• Right(A)
• Left(B)
• Underside(C)
• Rear
B
A
1. Cut out the appropriate knock-out piece (A,B,C) on the rear of the
indoor unit unless you connect the pipe directly from the rear.
07 INSTALLATION
Connect indoor and outdoor units with field-supplied copper pipes by means of flare connections. Use insulated seamless
refrigeration grade pipe only, (Cu DHP type according to ISO1337), degreased and deoxidized, suitable for operating pressures
of at least 4200 kPa and for burst pressure of at least 20700 kPa. Under no circumstances must sanitary type copper pipe be
used.
Outer Diameter
N•m
Torque
kgf•cm
2. Smooth the cut edges.
ø6.35 mm
14~18
140~180
3. Remove the protection caps of the pipes and connect the assembly
pipe to each pipe. Tighten the nuts first with your hands, and then with
a torque wrench, applying the following torque:
ø9.52 mm
34~42
350~430
ø12.70 mm
49~61
500~620
ø15.88 mm
68~82
690~830
• If you want to shorten or extend the pipes, refer to page 44~45.
4. Cut off the remaining foam insulation.
5. If necessary, bend the pipe to fit along the bottom of the indoor unit.
Then pull it out through the appropriate hole.
 The pipe should not project from the rear of the indoor unit.
 The bending radius should be 100 mm or more.
6. Pass the pipe through the hole in the wall.
7. For further details on how to connect to the outdoor unit and evacuate the air, refer to page 48~50.
• T he pipe will be insulated and fixed permanently into position after finishing the installation and the gas leak test;
refer to page 52 for further details.
• T ighten the flare nut with torque wrench according to specified method.
If the flare nut is over-tightened, the flare may break and cause refrigerant gas leakage.
• DO NOT WALL UP THE PIPE CONNECTION !
All refrigerant pipe connection must be easy accessible and serviceable.
English-43
A3050 MG Model IB&IM_DB68-05190A_HP_EN_UX.indd 43
2/17/2015 1:54:51 PM
Evacuating the indoor unit
The indoor unit is supplied with inert gas (nitrogen).
Before installing the unit, check if nitrogen gas flow out of indoor unit.
If this one isn’t true, DO NOT INSTALL THE UNIT since leakage could be inside the indoor unit.
1. Unscrew the caps at the end of each pipe.

All inert gas exhausts from the indoor unit.
• T o prevent dirt or foreign substances from getting into the pipes
during installation, do NOT remove the caps completely until you are
ready to connect the pipes.
• T he remaining air in the Refrigeration cycle, which contains moisture,
may cause malfunction on the compressor.
• Always contact the service center or a professional installation agency
for product installation.
Pipes
Unscrew the
caps
Cutting or extending the pipe
The length of the pipe can be:
• Extended up to : see table page 34
• Shorten up to: see page 34
If you need a pipe longer than 5 meters:
• You must add refrigerant to the pipes; otherwise, the indoor unit may freeze.
1. Make sure that you have all the required tools (pipe cutter, reamer, flaring tool and pipe holder).
2. If you want to shorten the pipe, cut it using a pipe cutter, ensuring that the cut edge remains at 90° with the side of the
pipe (see below examples of correct and incorrect cut edges).
Pipe
cutter
Oblique
Rough
Burr
Pipe
3. To prevent a gas leak, remove all burrs at the cut edge of the pipe using a reamer.
• Face the pipe down while removing the burrs to make sure that burrs do not get in to the pipe.
English-44
A3050 MG Model IB&IM_DB68-05190A_HP_EN_UX.indd 44
2/17/2015 1:54:52 PM
Cutting or extending the pipe
4. Put a flare nut slightly into the pipe and modify the flare.
B
45°
± 2°
R 0.4~0.8
Pipe
Outer Diameter (D)
Depth (A)
Flaring Size (B)
ø6.35 mm
1.3 mm
8.7 - 9.1 mm
ø9.52 mm
1.8 mm
12.8 - 13.2 mm
ø12.70 mm
2.0 mm
16.2 - 16.6 mm
ø15.88 mm
2.2 mm
19.3 - 19.7 mm
Flare
07 INSTALLATION
90°± 2°
5. Check if you flared the pipe correctly (see examples of incorrectly flared pipes below).
Correct
Inclined
Damaged
Surface
Cracked
Uneven
Thickness
6. Align the pipes to connect them easily. Tighten the flare nuts first with your hands, and then with a torque wrench,
applying the following torque:
Flare nut
Indoor outlet pipe
Connecting pipe
Outer Diameter
ø6.35 mm
ø9.52 mm
ø12.70 mm
ø15.88 mm
Torque
N•m
14~18
34~42
49~61
68~82
kgf•cm
140~180
350~430
500~620
690~830
• E xcessive torque can be cause of gas leakage. If extending pipe by welding/brazing please ensure nitrogen is
used during welding/brazing process. The joint must be accessible and serviceable.
• The holder system is detachable as shown.
Holder system
(detachable)
7. For further details on how to connect to the outdoor unit and evacuate the air, refer to page 48~50.
• T ighten the flare nut with torque wrench according to specified method.
If the flare nut is over-tightened, the flare may break and cause refrigerant gas leakage.
English-45
A3050 MG Model IB&IM_DB68-05190A_HP_EN_UX.indd 45
2/17/2015 1:54:54 PM
Installing and connecting the drain hose of the indoor unit
When installing the drain hose for the indoor unit, check if condensation draining is adequate.
When passing the drain hose through the 65 mm hole drilled in the wall, check the followings:
Wall
Indoor unit
Drain hose
The drain hose must NOT
slant upwards.
5cm
less
The end of the drain hose
must NOT be placed under
water.
The drain hose must not
be bent.
After completing the
installation of the drain
hose, pour water into
the drain pan to check
whether the hose is well
drained.
Ditch
Keep a clearance of at least
Do not place the end of the
5 cm between the end of the drain hose in a hollow.
drain hose and the ground.
1) Correct connection
Drain hose
2) Incorrect connection
Pipe
Drain hose
Pipe
• Don’t tie drain hose to the assembly pipe which may lead to water leakage.
• If the diameter of the connection hose is smaller than the product's drain hose, water leakage may occur.
Drain hose installation
1. If necessary, connect the 2 meter extension drain hose to the drain hose.
2. If you use the extension drain hose, insulate the inside of the extension drain hose with a shield.
3. Fit the drain hose into 1 of 2 drain hose holes, then fix the end of the drain hose tightly with a clamp.
• If you do not use the other drain hose hole,
block it with a rubber stopper.
4. When extending the Drain Hose, hold the end of Drain Hose and Extended Hose,
rotate and insert the drain hose into Extended hose for 40~45 mm. Make sure the
two hoses are firmly connected, there is no water leakage.
Drain hose hole
5. Connect the Drain Hose after using Foam Insulation to wrap the Extended Hose. Then, Use vinyl tape to wrap the
each side of connection by 20 mm .
English-46
A3050 MG Model IB&IM_DB68-05190A_HP_EN_UX.indd 46
2/17/2015 1:54:56 PM
40~45 mm
Drain hose Extension
drain hose
Drain hose
Vinyl Tape
6. Pass the drain hose under the refrigerant pipe, keeping the drain hose tight.
Shield
7. Pass the drain hose through the hole in the wall. Check if it slants
downwards as seen in the picture.
8. Using natural drainage method, check the drainage is normal.
Drain hose
Foam Insulation
Extension drain hose
07 INSTALLATION
Extension
drain hose
20 mm 20 mm
or more or more
• T he hose will be fixed permanently into position after finishing the installation and the gas leak test;
refer to page 52 for further details.
• M
ake sure the installed direction of the drain hose is correct.
Inadequate installation may cause condensate water leakage.
• If the drain hose is routed inside the room, insulate the hose so that dripping condensation does not damage the
furniture or floors.
• DO NOT WALL UP THE DRAIN HOSE CONNECTION !
Drain hose connection must be easy accessible and serviceable.
Changing direction of the drain hose
Change the direction only when it is necessary.
1. Detach the rubber cap with the pliers.
2. Detach the drain hose by pulling it and turning to the right.
3. Insert the drain hose by fixing it with the screw into the groove of the drain hose and the outlet of the drain pan.
Screw hole
Screw
Drain hose
4. Attach the rubber cap with a screwdriver by turning it to the left until it fixes to the end of the groove.
Drain pan outlet
Rubber cap
5. Check for leakage on both side of the drain outlet.
 Direction of the drained water
Pour the water in direction of arrow.
• M
ake sure the indoor unit is in upright position when you pour water to check for leakage.
Make sure that the water does not overflow onto the electrical part.
English-47
A3050 MG Model IB&IM_DB68-05190A_HP_EN_UX.indd 47
2/17/2015 1:54:57 PM
Installing and connecting the drain hose of the outdoor unit
ARHS
While heating, ice may accumulate. During the process of defrosting, check if condensation draining is adequate. For adequate
draining, do the following.
1. Insert the drain plug into the drain hole on the underside of the outdoor unit.
• T o avoid drain plug from contacting the ground, secure gap between the
ground and the bottom surface of the outdoor unit.
Drain plug
Drain hole
Bottom surface of outdoor unit
2. Connect a drain hose to the drain plug.
Drain hole
Drain plug
3. Ensure that condensation draining is adequate.
Drain hose
Snow-proof hood
• In areas with heavy snow fall, piled snow could block the air intake.
To avoid this incident, install a frame that is higher than estimated snow
fall. In addition, install a snow-proof hood to avoid snow from piling on the
outdoor unit.
Estimated
snow fall Frame
Ground
Evacuating the connected pipes
The outdoor unit is loaded with sufficient R-410A refrigerant. Do not vent R-410A into atmosphere: it is a fluorinated
greenhouse gas, covered by Kyoto Protocol, with a Global Warming Potential (GWP) = 2088
You should evacuate the air in the indoor unit and in the pipe. If air remains in the refrigerant pipes, it affects the compressor.
It may cause reduction of cooling capacity and malfunction. Use Vacuum Pump as seen in the picture.
• W
hen installing, make sure there is no leakage. When recovering the refrigerant, ground the compressor first
before removing the connection pipe. If the refrigerant pipe is not properly connected and the compressor works
with the service valve open, the pipe inhales the air and it makes the pressure inside of the refrigerant cycle
abnormally high. It may cause explosion and injury.
English-48
A3050 MG Model IB&IM_DB68-05190A_HP_EN_UX.indd 48
2/17/2015 1:54:58 PM
Evacuating the connected pipes
1. Connect each assembly pipe to the appropriate valve on the outdoor unit and
tighten the flare nut.
Outdoor unit
Indoor unit
Gas pipe side
Liquid pipe side
• Excessive torque can be cause of gas leakage.
Outer
Diameter
• M
ake the electrical connection and leave the system into “stand by
mode”. Do not turn on the system!
This is necessary for better vacuum operation (full OPEN position of
Electronic Expansion Valve - EEV -).
ø6.35 mm
ø9.52 mm
ø12.70 mm
ø15.88 mm
3. Connect the charging hose of the low-pressure side of manifold gauge to a
gas service port as seen in the picture.
Torque
N•m
kgf•cm
14~18 140~180
34~42 350~430
49~61 500~620
68~82 690~830
07 INSTALLATION
2. Tighten the flare nut first with your hands, and then with a torque wrench,
applying the following torque.
Manifold gauge
4. Open the valve of the low pressure side of manifold gauge counterclockwise.
5. Evacuate the air in the connected pipes using the vacuum pump for about
15 minutes.
Make sure that pressure gauge shows -0.1 MPa(-76 cmHg) after about
Valve
Gas service port
<Low pressure>
10 minutes.
This procedure is very important to avoid a gas leak.
Close the valve of the low pressure side of manifold gauge clockwise.
Turn off the vacuum pump.
Check for 2 minutes if there is any pressure change.
Remove the hose of the low pressure side of manifold gauge.
Liquid service port
<High pressure>
Vacuum
Pump
(Backward flowing
prevention)
6. Set a valve cork of liquid and gas service port to the open position.
Adding Refrigerant
Add refrigerant charge according to table below:
If you use a pipe longer than 5 m,
‘A’ g of refrigerant R-410A must be added for each extra meter.
If you use a pipe shorter than 5 m,
The evacuate time is normal.
Refer to the Service Manual for further details.
Model
A
18/24HV
18HS
15
24HS
40
• T he remaining air in the Refrigeration cycle, which contains moisture, may cause malfunction on the compressor.
• Always contact the service center or a professional installation agency for product installation.
English-49
A3050 MG Model IB&IM_DB68-05190A_HP_EN_UX.indd 49
2/17/2015 1:54:58 PM
Evacuating the connected pipes
Charging the refrigerant under conditions of liquid by using a liquid pipe
R-410A is a mixed type of refrigerant. It is necessary for recharging under conditions of liquid. When recharging refrigerant from
the refrigerant cylinder to the equipment, follow the instructions below.
1. Before recharging, check whether the cylinder has a siphon or not.
There are two ways to recharge the refrigerant.
Cylinder with siphon
Cylinder without siphon
Siphon
 Charge the refrigerant standing the
cylinder upright.
 Charge the refrigerant turning the cylinder
upside down.
• If R-410A refrigerant is charged with gas, the composition of the charged refrigerant changes and the
characteristics of the equipment vary.
• During the measuring operation of refrigerant quantity added use electronic scales.
If cylinder doesn’t have syphon, upset it.
English-50
A3050 MG Model IB&IM_DB68-05190A_HP_EN_UX.indd 50
2/17/2015 1:54:58 PM
Performing the gas leak tests
Make sure to check for gas leaks before completing the installation process (connecting the assembly pipe and hose between
indoor unit and outdoor unit, insulating the cables, hose and pipe, and fixing the indoor unit to the installation plate).
07 INSTALLATION
A
D
C
B
Test part for outdoor unit
Test part for indoor unit
Tightening torque for body cap
(Refer to the table)
 Before inspecting the leakage, use a torque wrench
to close the cap for the service valve. (Comply with a
tightening torque for each size of the diameter,and
tighten the cap firmly to prevent any leakage.).
 To check for any possible leakage, insert inert gas into
the pipes connected to indoor/outdoor units and
check the connection part of the indoor/outdoor units
with soap lather or liquid for leakage test.
Spindle
Charging
core
R-22: Diameter of the screw - 7/16-20UNF
R-410A: Diameter of the screw - 1/2-20UNF
Tightening torque for charging port cap
(Refer to the table)
To check for gas leaks on the outdoor unit,
Check the valve A and B using a leak detector.
To check for gas leaks on the indoor unit,
Check the flare nut C and D using a leak detector.
Outer
Diameter
(mm)
Tightening torque
Body cap (N•m)
Charging port cap
(N•m)
20 ~ 25
20 ~ 25
25 ~ 30
30 ~ 35
35 ~ 40
10 ~ 12
ø 6.35
ø 9.52
ø12.70
ø15.88
ø19.05
( 1 N•m = 10 kgf•cm )
Leak test with nitrogen (before opening valves)
In order to detect basic refrigerant leaks, before recreating the vacuum and recirculating the R-410A, it’s responsible of
installer to pressurize the whole system with nitrogen (using a cylinder with pressure reducer) at a pressure above 40 bar
(gauge).
Leak test with R-410A (after opening valves)
Before opening valves, discharge all the nitrogen from the system and create vacuum according to page 48~50.
After opening valves, check leaks using a leak detector for refrigerant.
Pump down (before disconnecting the refrigerant connections for unit repair, removal or disposal)
Pump-down is an operation intended to collect all the system refrigerant in the outdoor unit.
This operation must be carried out before disconnecting the refrigerant tubing in order to avoid refrigerant loss to the
atmosphere.
 Shut off the liquid valve with the Allen wrench.
 Turn the system on in cooling with fan operating at high velocity.
(Compressor will immediately start, provided 3 minutes have elapsed since the last stop).
 After 2 minutes of operation, shut the suction valve with the same wrench.
 Turn the system off and switch mains supply off.
 Disconnect tubing. After disconnection, protect valves and tubing ends from dust.
 Compressor damage may occur if run at a negative suction pressure.
English-51
A3050 MG Model IB&IM_DB68-05190A_HP_EN_UX.indd 51
2/17/2015 1:54:59 PM
Fixing the indoor unit in place
Perform the following work on the area where gas leak test was done priory.
After checking for gas leaks in the system, insulate the pipe, hose and cables.
Then place the indoor unit on the installation plate.
Insulation
1. To minimise condensation problems, wrap foam insulation (as shown in the
figure) on a part without insulation on the end of the pipes.
Pipes
2. Wind the pipe, assembly cable and drain hose with vinyl tape.
3. Place the bundle (the pipe, assembly cable and drain hose) in the lower part
of the indoor unit carefully so it does not project from the rear of the indoor
unit.
4. Hook the indoor unit to the installation plate and move the unit to the right
and left until it is securely in place.
Installation
plate
Vinyl tape
Connecting
pipes
Connecting wires
• M
ake sure pipe does not move when you install the indoor unit on
an installation plate.
Drain hose
5. Wrap the rest of the pipe with vinyl tape.
6. Attach the pipe to the wall using clamps (optional).
Fixing the outdoor unit in place
'X' mm
'Y' mm
Install the outdoor unit in level on a stable base to help avoid the generation of noise and
vibration, especially when installing the unit close to a neighbor.
If you install the outdoor unit in a place exposed to strong winds or at a height, fix it to an
appropriate support (wall or ground).
1. Place the outdoor unit as indicated on the top of the unit to let the discharged air out
properly.
2. Fix the outdoor unit in level to an appropriate support using anchor bolts.
3. If the outdoor unit is exposed to strong winds, install shield plates around the
outdoor unit so that the fan can operate correctly.
Rubber leg
Model
X
Y
18/24HV
18HS
660
340
24HS
645
340
• Secure the rubber leg to help prevent the generation of noise and vibration.
Outdoor unit installed on the wall by rack
• E nsure the wall will be able to suspend the weight of rack and
outdoor unit;
• Install the rack close to the column as much as possible;
• Install proper grommet in order to help reduce noise and residual
vibration transferred by outdoor unit towards wall.
Designed to cut off residual vibration
from outdoor unit to rack.
(not supplied with product)
Soft rubber designed to cut off
vibration from rack to wall.
(not supplied with product)
English-52
A3050 MG Model IB&IM_DB68-05190A_HP_EN_UX.indd 52
2/17/2015 1:55:00 PM
Smart Install mode
This model supports Smart Install mode which checks installation status to find out if there is any problems with any of the
functions. Execute Smart Install mode after installation.
2. When the air conditioner is in standby status, use the remote controller to start the Smart Install mode.
1) Press the [SET], [Mode],[Power]
button simultaneously for 4 seconds.
 Smart Install mode can be operated only with the supplied remote controller.
 During the Smart install mode procedure, remote controller cannot be operated.
07 INSTALLATION
1. Check the installation status of the air conditioner.
1) Check the power supply, service valve (if it's open), power cable of the indoor and outdoor unit and amount of
additional refrigerant required for pipe extension.
2) Status of the indicator after supplying the power : Standby status
 Remote controller may be different (image/functions) depending on the model.
English-53
A3050 MG Model IB&IM_DB68-05190A_HP_EN_UX.indd 53
2/17/2015 1:55:07 PM
Smart Install mode
1) Smart Install mode in progress
• 88 Display : Progress will be diplayed in 0~99.
• LED Display : Indicator on the indoor unit display will blink in sequence and then all indicators will blink. (This will be repeated.)
TYPE
88 Display
LED Display
LED 1
LED 2
LED 3
Indoor unit indicator
 Display may be different depending on the model.
1. Smart Install mode will end.
1) Smart Install mode will take approximately 7~13 minutes. (Actual time may be different depending on the model.)
2) When Installation is successful : Smart Install mode will end with ringing sound and the air conditioner will be in standby status.
(Error message will not be displayed on the indoor unit indicator and the remote controller and buttons on the indoor unit will work
normally.)
3) When installation is not successful : Smart Install mode will end and error message will be displayed on the indoor unit display.
1. Take necessary measures when error occurs.
-- Refer to the service manual for necessary measures for each error that occurs.
2. Use the product after taking care of the error that occurs.
Error indicator
LED Display
LED 1
LED 2
LED 3
Error
Measures to take by an installer
Communication Error
between Indoor and outdoor
unit
1.Check the connection wire between indoor and
outdoor unit. (whether the power cable and
communication cable is crossed or not)
Display
/
/
,
Error on indoor
temperature sensor
1.Check the connection of the connector
Error on indoor heat
exchanger
1.Check the connection of the connector
Error on indoor fan
motor
1.Check the connection of the connector
2.Remove foreign substance (Check for the cause
that restrains motor)
1.Re-set options
display and all
LED blinks
EEPROM/Option error
,
Above LED pattern is displayed when
there's error is occurred on outdoor unit.
Check the LED display on outdoor unit for
the details.

: Off /
: Blinking /
Refrigerant flow blocking
Error
1.Check if the service valve is completely open.
2.Check if there's any blockage in the refrigerant pipe
which connects indoor and outdoor unit.
3.Check for refrigerant leak.
Lack of Refrigerant (For
Inverter model only)
1.Check if sufficient amount of additional refrigerant
was charged for the pipe length that exceeds 7.5
m.
2.Check for refrigerant leak between valve and pipe
connection.
: On
English-54
A3050 MG Model IB&IM_DB68-05190A_HP_EN_UX.indd 54
2/17/2015 1:55:10 PM
Final check and trial operation
To complete the installation, perform the following checks and tests to
ensure that the air conditioner operates correctly.
1. Press the Power
07 INSTALLATION
Check the followings:
• Strength of the installation site
• Tightness of pipe connection to detect gas leak
• Electric wiring connection
• Heat-resistant insulation of the pipe
• Drainage
• Grounding conductor connection
• Correct operation (follow the steps below)
button and check the following:
 The indicator on the indoor unit lights up.
The airflow blade opens and the fan gears up for operation.
2. Press the Mode button to select Cool or Heat mode.
 In Cool mode, use
Temp + or – button and set the temperature at 16 °C.
 In Heat mode, use
Temp + or – button and set the temperature at 30 °C.
• A
pproximately 3~5 minutes later, outdoor unit will start to operate and the
Cool or Warm air will blow out.
• After 12 minutes of stationary condition check the indoor unit air treatment.
Cooling mode (indoor unit check)  Inlet air temp. - Outlet air temp:
From 10 °C to 12 °C (indicative delta T)
Heating mode (indoor unit check)  Outlet air temp. - Inlet air temp:
From 11 °C to 14 °C (indicative delta T)
In heating mode, the indoor fan motor can remain off to avoid cold air blown into
conditioned space.
3. Press the Air swing button and check the following:
 The airflow blades work properly.
4. Press the Power
button to stop the operation.
• W
hen you complete the installation successfully, hand over this manual to the user for storage in a handy and safe
place.
Pump down procedure (when removing the product)
1. Press the Power button on the indoor unit for 5 seconds. Beep will sound immediately to let you know that the
product is ready for pump down procedure. Please let the compressor run for more than 5 minutes.
2 . Release the valve caps on High and Low pressure side.
3 . Use L wrench to close the valve on the high pressure side.
4 . After approximately 2 minutes, close the valve on the low pressure side.
5 . Stop operation of the air conditioner by pressing the Power
button on the indoor unit or remote controller.
6 . Disconnect the pipes.
English-55
A3050 MG Model IB&IM_DB68-05190A_HP_EN_UX.indd 55
2/17/2015 1:55:11 PM
Packing and unpacking guide
Indoor unit

Packing the unit as below procedure
1. Put the indoor unit onto the packing case.
2. Assemble cushion-both side of indoor unit. (Left and Right)
3. Seal the packing case.

Unpacking the unit as below procedure
1. Open the packing case.
2. Take out the both side of cushion(Left and Right).
3. Move the set from the packing case.
Outdoor unit

Packing the unit as below procedure
1. Put the outdoor unit onto the cushion-bottom.
2. Put the cushion-top onto the outdoor unit
3. Put the packing case from the top of set.
4. Seal the packing case.

Unpacking the unit as below procedure
1. Take out the packing case from the set.
2. Take out the cushion-top.
3. Move the set from the cushion-bottom.
English-56
A3050 MG Model IB&IM_DB68-05190A_HP_EN_UX.indd 56
2/17/2015 1:55:12 PM
How to connect your extended power cables
Items to prepare
(compressor and insulation tape should be prepared by an installation technician.)
Crimping pliers
Connection sleeve (mm)
Insulation tape
Contraction tube (mm)
MH-14
20xØ7.0(HxOD)
Width 18 mm
50xØ8.0(LxOD)
Shape
1. As shown in the figure, peel off the shields from the rubber/wire
of the power cable.
- Peel off 20 mm of the wire shields of the tube installed already.
• After peeling off the tube wire, you must insert a contraction tube.
(Unit: mm)
Power cable (provided by us)
20
20
07 INSTALLATION
Tools
Spec
20
60
120
180
Wire tube power cable
20
2. Insert both sides of core wire of the power cable into the connection sleeve.
Connection sleeve
3. Using a compressor, compress the two points and flip it over
and compress another two points in the same location.
- The compression dimension should be 8.0.
- After compressing it, pull both sides of the wire to
make sure it is firmly pressed.
Comp. dim.
Compress it 4 times
5 mm
4. Wrap it with the insulation tape twice and position your
contraction tube in the middle of the insulation tape.
5. Apply heat to the contraction tube to contract it.
Insulation tape
40 mm
Contraction tube
6. After tube contraction work is completed, wrap it with the
insulation tape to finish.
Insulation tape
• In case of extending the electric wire, please DO NOT use a round-shaped pressing socket.
- Incomplete wire connections can cause electric shock or a fire.
English-57
A3050 MG Model IB&IM_DB68-05190A_HP_EN_UX.indd 57
2/17/2015 1:55:13 PM
QUESTIONS OR COMMENTS?
COUNTRY
CALL
OR VISIT US ONLINE AT
IRAN
021-8255 [CE]
021-42132 [HHP]
www.samsung.com/iran/support
SAUDI ARABIA
8002474357
www.samsung.com/sa/support
www.samsung.com/sa_en/support
U.A.E
800-SAMSUNG (800 - 726 7864)
www.samsung.com/ae/support
www.samsung.com/ae_ar/support
QATAR
800-CALL (800-2255)
www.samsung.com/ae/support
www.samsung.com/ae_ar/support
BAHRAIN
8000-GSAM (8000-4726)
www.samsung.com/ae/support
www.samsung.com/ae_ar/support
OMAN
800-SAMSUNG (800 - 726 7864)
www.samsung.com/ae/support
www.samsung.com/ae_ar/support
JORDAN
0800-22273
06 5777444
www.samsung.com/Levant/support
SYRIA
18252273
www.samsung.com/Levant/support
EGYPT
08000-7267864
16580
www.samsung.com/eg/support
MOROCCO
080 100 22 55
www.samsung.com/n_africa/support
KUWAIT
183-CALL (183-2255)
www.samsung.com/ae/support
www.samsung.com/ae_ar/support
NIGERIA
0800-726-7864
www. samsung. com/africa_en/support
ALGERIA
021 36 11 00
www.samsung.com/n_africa/support
PAKISTAN
0800-Samsung (72678)
www.samsung.com/pk/support
TUNISIA
80-1000-12
www.samsung.com/n_africa/support
SOUTH AFRICA
0860 SAMSUNG (726 7864)
www.samsung.com/support
GHANA
0800-10077
0302-200077
www.samsung.com/africa_en/support
BOTSWANA
8007260000
www.samsung.com/support
NAMIBIA
08 197 267 864
www.samsung.com/support
ZAMBIA
0211 350370
www.samsung.com/support
A3050 MG Model IB&IM_DB68-05190A_HP_EN_UX.indd 58
2/17/2015 1:55:14 PM
Download PDF

advertising