Samsung | WM55H | Samsung Samsung Flip Display Benutzerhandbuch

User Manual
WM55H
The colour and the appearance may differ depending on the product, and the content in the
manual is subject to change without prior notice to improve the performance.
•• An administration fee may be charged if either
–– (a) an engineer is called out at your request and there is no defect in the product
(i.e. where you have failed to read this user manual).
–– (b) you bring the unit to a repair Centre and there is no defect in the product
(i.e. where you have failed to read this user manual).
•• The amount of such administration charge will be advised to you before any work or home
visit is carried out.
© Samsung Electronics
Samsung Electronics owns the copyright for this manual. Use or reproduction of this manual in parts or entirety without the authorization of Samsung Electronics is prohibited.
Trademarks other than Samsung Electronics are property of their respective owners.
Table of contents
Before Using the Product
Writing
Safety Precautions
4
Storage4
Electricity and safety
4
Installation5
Operation6
What's a 'Roll'?
20
Sending Email
Screen Elements
21
Printing33
Installing Flip Printing Software
33
Setting up the printer
33
Precautions for Use
8
Preparations
Checking the Components
Export
Drawing / Erasing
22
Changing pen thickness
22
Changing the pen colour
22
Erasing22
Managing Rolls
Opening rolls
23
24
Page Viewer
25
9
Exporting to a USB Device
35
Exporting from a Network Drive
35
Menu
Pen36
Parts10
Ports12
Import
Before Installing the Product (Installation
Guide)13
Rotation13
Ventilation13
Connecting to a Mobile Device
27
Connecting using Smart View or Screen
Mirroring27
Connecting using NFC tagging
27
Installing the Wall Mount
Installing the Wall Mount
Wall Mount Kit Specifications (VESA)
Connecting to a Laptop
Connecting using a cable
Connecting via the WiFi Display function
28
28
28
Troubleshooting Guide
Importing from a USB Device
29
Problems and Solutions
Importing from a Network Drive
29
Source Window
30
14
14
14
Connecting to a network
15
Network Settings (Wired)
15
Network Settings (Wireless)
17
Use WPS19
32
Connect37
System42
Picture44
Support45
46
2
Table of contents
Specifications
General51
Preset Timing Modes
53
Appendix
Responsibility for the Pay Service (Cost to
Customers)55
Not a product defect
55
A Product damage caused by customer's fault 55
Others55
Prevention of Afterimage Burn-in
What is afterimage burn-in?
Recommended prevention practices
56
56
56
Licence56
3
Chapter 01
Before Using the Product
Safety Precautions
Warning
A serious or fatal injury may result if instructions are not followed.
Caution
Personal injury or damage to properties may result if instructions are not followed.
Storage
Due to the characteristics of high-glossy products, using a UV humidifier nearby may create
white-colored stains on the product.
"" Contact Customer Service Centre if the inside of the product needs cleaning (service fee
will be charged).
Electricity and safety
Warning
Activities marked by this symbol are prohibited.
Do not use a damaged power cord or plug, or a loose power socket.
An electric shock or fire may result.
Do not use multiple products with a single power socket.
Instructions marked by this symbol must be followed.
Overheated power sockets may cause a fire.
Do not touch the power plug with wet hands. Otherwise, an electric shock may result.
Do not bend or pull the power cord with force. Be careful not to leave the power cord
under a heavy object.
Damage to the cord may result in a fire or electric shock.
Do not place the power cord or product near heat sources.
A fire or electric shock may result.
4
Insert the power plug all the way in so it is not loose.
An unsecure connection may cause a fire.
Connect the power plug to a grounded power socket (type 1 insulated devices only).
An electric shock or injury may result.
Clean any dust around the pins of the power plug or the power socket with a dry cloth.
A fire may result.
Caution
Installation
Warning
DO NOT PLACE CANDLES, INSECT REPELLANTS OR CIGARETTES ON TOP OF THE
PRODUCT. DO NOT INSTALL THE PRODUCT NEAR HEAT SOURCES.
A fire may result.
Do not install the product in poorly ventilated spaces such as a bookcase or closet.
Do not disconnect the power cord while the product is being used.
The product may become damaged by an electric shock.
Only use the power cord provided with your product by Samsung. Do not use the power
cord with other products.
An increased internal temperature may cause a fire.
Do not install the product on an unstable or vibrating surface (insecure shelf, sloped
surface, etc.)
•• The product may fall and become damaged and/or cause an injury.
A fire or electric shock may result.
•• Using the product in an area with excess vibration may damage the product or
cause a fire.
Keep the power socket where the power cord is connected unobstructed.
Do not expose the product to direct sunlight, heat, or a hot object such as a stove.
The power cord must be disconnected to cut off power to the product when an issue
occurs.
The product lifespan may be reduced or a fire may result.
Hold the plug when disconnecting the power cord from the power socket.
•• The product may fall and injure children.
An electric shock or fire may result.
•• As the front is heavy, install the product on a flat and stable surface.
Do not install the product within the reach of young children.
Edible oil, such as soybean oil, can damage or deform the product. Do not install the
product in a kitchen or near a kitchen counter.
Have a technician install the wall-mount hanger.
•• Installation by an unqualified person can result in an injury.
•• Only use approved cabinets.
Install the product at least 10 cm away from the wall to allow ventilation.
An increased internal temperature may cause a fire.
5
Keep the plastic packaging out of the reach of children.
Children may suffocate.
Do not install the product in a vehicle or a place exposed to dust, moisture (water drips,
etc.), oil, or smoke.
A fire or electric shock may result.
Caution
Operation
Warning
There is a high voltage inside the product. Never disassemble, repair or modify the
product yourself.
•• A fire or electric shock may result.
Do not set down the product on its front.
The screen may become damaged.
Do not drop the product while moving.
•• Contact Samsung Customer Service Centre for repairs.
Do not let children hang from the product or climb on top of it.
Children may become injured or seriously harmed.
Product failure or personal injury may result.
If the product is dropped or the outer case is damaged, turn off the power switch and
disconnect the power cord. Then contact Samsung Customer Service Centre.
Set down the product gently.
Continued use can result in a fire or electric shock.
Product failure or personal injury may result.
Do not leave heavy objects or items that children like (toys, sweets, etc.) on top of the
product.
Installing the product in an unusual place (a place exposed to a lot of fine dust, chemical
substances, extreme temperatures or a significant presence of moisture, or a place
where the product will operate continuously for an extended period of time) may
seriously affect its performance.
Be sure to consult Samsung Customer Service Centre if you want to install the
product at such a place.
The product or heavy objects may fall as children try to reach for the toys or sweets
resulting in a serious injury.
Do not move the product by pulling the power cord or any cable.
Product failure, an electric shock or fire may result from a damaged cable.
Do not lift or move the product by pulling the power cord or any cable.
Product failure, an electric shock or fire may result from a damaged cable.
Ensure the vents are not blocked by tablecloths or curtains.
An increased internal temperature may cause a fire.
Do not insert metallic objects (chopsticks, coins, hairpins, etc) or objects that burn easily
(paper, matches, etc) into the product (via the vent or input/output ports, etc).
•• Be sure to power off the product and disconnect the power cord when water
or other foreign substances have entered the product. Then contact Samsung
Customer Service Centre.
•• Product failure, an electric shock or fire may result.
6
Do not place objects containing liquid (vases, pots, bottles, etc) or metallic objects on
top of the product.
•• Be sure to power off the product and disconnect the power cord when water
or other foreign substances have entered the product. Then contact Samsung
Customer Service Centre.
•• Product failure, an electric shock or fire may result.
Before moving the product, turn off the power switch and disconnect the power cable
and all other connected cables.
Damage to the cord may result in a fire or electric shock.
If the product generates abnormal sounds, a burning smell or smoke, disconnect the
power cord immediately and contact Samsung Customer Service Centre.
An electric shock or fire may result.
During a lightning or thunderstorm, power off the product and remove the power cable.
A fire or electric shock may result.
Do not drop objects on the product or apply impact.
A fire or electric shock may result.
Caution
Do not use humidifiers or stoves around the product.
A fire or electric shock may result.
Do not touch the screen when the product has been turned on for an extended period of
time as it will become hot.
Do not place heavy objects on the product.
Product failure or personal injury may result.
Leaving the screen fixed on a stationary image for an extended period of time may cause
afterimage burn-in or defective pixels.
Activate power-saving mode or a moving-picture screen saver if you will not be using
the product for an extended period of time.
Disconnect the power cord from the power socket if you do not plan on using the product
for an extended period of time (vacation, etc).
Dust accumulation combined with heat can cause a fire, electric shock or electric
leakage.
If a gas leakage is found, do not touch the product or power plug. Also, ventilate the area
immediately.
Use the product at the recommended resolution and frequency.
Sparks can cause an explosion or fire.
Do not use or keep combustible spray or an inflammable substance near the product.
Looking at the screen too close for an extended period of time can deteriorate your
eyesight.
An explosion or fire may result.
Rest your eyes for more than 5 minutes for every 1 hour of product use.
Your eyesight may deteriorate.
Eye fatigue will be relieved.
Store small accessories out of the reach of children.
7
Precautions for Use
Be careful that if you use the supplied pen with a load exceeding 2.5 kg, scratches may occur on the
protective glass.
If you use a ballpoint pen other than the supplied pen, be careful that the screen may be stained
with ink or damaged.
"" We recommend that you use the supplied pen. Do not use sharp, pointed objects other than
the pen.
"" If dust or dirt from the supplied pen remains on the protective glass, clean it referring to
the instructions below.
Cleaning the exterior and display
Wipe the surface with a slightly wet, soft cloth, and then wipe with a dry cloth.
1
2
3
8
Chapter 02
Preparations
Checking the Components
"" Contact the vendor where you
purchased the product if any
components are missing.
Quick Setup Guide
"" The appearance of the components
may differ from the images shown.
Touch Pen X 2
Warranty card
(Not available in some locations)
USB cable
Regulatory guide
Power cord
Cover Terminal
9
Parts
"" The colour and shape of parts may differ from what is shown. Specifications are subject to change without
notice to improve quality.
Parts
Description
Keep the touch pen in place.
Pen holder
•• When the product is turned off and you lift the pen from the pen holder, the
screen turns on.
•• When the product is in the screen saver mode and you lift the pen from the pen
holder, the screen turns on.
Speaker
•• Tag your mobile device to the NFC pad for connection.
"" In writing mode, an NFC tagging can automatically perform Smart View or
Screen Mirroring on your mobile device.
NFC pad
"" This function is supported only on Android 8.0 Oreo version or later of
Samsung mobile devices.
•• Tag an NFC card to the NFC pad to enter an email address automatically.
"" While creating an email, an email address is automatically entered if it is read
from the encoded NFC tag.
"" For how to enter an email address in the NFC card, refer to 'Sending Email'.
•• Press and hold the button to turn off the product.
Power button
•• In writing mode, shortly press the Power button to switch to the screen saver
mode.
•• In HDMI or Screen Mirroring mode, press the Power button to exit full screen
mode.
10
Parts
Description
Detects user's motions to turn the product on or off.
The screen is touched or the touch pen is lifted.
Motion is detected.
Whiteboard /
Blackboard
Motion is detected.
Screen Saver
There is no motion
for 1 hour.
Power Off
There is no motion
for 1 hour.
"" If the product is turned off because no motion is detected, it operates as follows:
→ System → Advanced Settings → Auto Save is set to On: The last
–– When
roll you are creating is displayed on the screen.
Motion sensor
→ System → Advanced Settings → Auto Save is set to Off: A new roll
–– When
is displayed on the screen.
"" Only when
→ System → Advanced Settings → Motion Sensor is set to Off, the
product automatically turns off at the time set at Auto Power Off.
"" When the screen of a mobile device and laptop is displayed on the product in the
full screen mode, the product does not switch to the screen saver mode.
"" When the screen is turned off, it may turn on in the screen saver mode due to the
surrounding environment and illumination. To turn the product's screen on or off
→ System → Advanced
with the Power button only, set Motion Sensor to Off at
Settings.
•• For ensuring normal operation of the motion sensor, do not install the
product in a place exposed to direct sunlight.
•• Do not hide the front of the motion sensor with an object.
•• When there are any foreign substances on the motion sensor, wipe them
with a soft cloth.
11
Ports
"" The colour and shape of parts may differ from what is shown. Specifications are subject to change without
notice to improve quality.
Ports
USB
Description
(1.0A)
Connect to a USB memory device.
"" The USB ports on the product accept a maximum constant current of 1.0A. If the
maximum value is exceeded, USB ports may not work.
LAN
Connects to a network using a LAN cable. (10/100 Mbps)
"" Use Cat7(*STP Type) cable for the connection.
*Shielded Twist Pair.
RS232C IN
Dedicated to service technicians.
HDMI IN
Connects to a source device using a HDMI cable.
TOUCH OUT
Connects to a PC using a USB cable. You can operate the PC screen by touching the
product screen.
USB
Connect to a USB memory device.
(5V 0.5A)
TOUCH
OUT
HDMI IN
RS232C
IN
LAN
USB
(1.0A)
"" The USB ports on the product accept a maximum constant current of 0.5A. If the
maximum value is exceeded, USB ports may not work.
USB
(5V 0.5A)
12
Before Installing the Product (Installation
Guide)
There is a product-specific stand sold separately from Samsung, and you can install it on the
wall, too.
Rotation
"" Contact Samsung Customer Service Centre for further details.
•• To use the product in landscape orientation, turn the product anticlockwise so that the
sensor part faces downward.
Ventilation
"" Contact Samsung Customer Service Centre for further details.
Installation on a Perpendicular Wall
A Minimum 15 mm
B Ambient temperature: 35℃ or less
"" When installing the product on a perpendicular wall, allow at least 15
mm of space between the product and wall surface for ventilation and
ensure that the ambient temperature is kept below 35°C.
A
B
Installation on an Indented Wall
A Minimum 15 mm
B Minimum 25 mm
B
C Ambient temperature: 35℃ or less
"" When installing the product on an indented wall, allow at least the
space specified above between the product and wall for ventilation and
ensure that the ambient temperature is kept below 35°C.
A
B
C
13
Installing the Wall Mount
Installing the Wall Mount
•• The wall mount kit allows you to mount the product on the wall.
•• For detailed information on installing the wall mount, see the instructions provided with the wall mount.
•• We recommend you contact a technician for assistance when installing the wall mount bracket.
•• Samsung Electronics is not responsible for any damage to the product or injury to yourself or others if you select to install the wall mount on your own.
Wall Mount Kit Specifications (VESA)
•• Samsung wall mount kits contain a detailed installation manual and all parts necessary for assembly are
provided.
"" Install your wall mount on a solid wall perpendicular to the floor.
To install the product on the other wall area, contact the nearest
agency.
•• Do not use screws that are longer than the standard length or do not comply with the VESA standard screw
specifications. Screws that are too long may cause damage to the inside of the product.
If you install the product on a slanted wall, it may fall and result in
severe personal injury.
•• For wall mounts that do not comply with the VESA standard screw specifications, the length of the screws may
differ depending on the wall mount specifications.
•• Do not fasten the screws too firmly. This may damage the product or cause the product to fall, leading to
personal injury. Samsung is not liable for these kinds of accidents.
•• Samsung is not liable for product damage or personal injury when a non-VESA or non-specified wall mount is
used or the consumer fails to follow the product installation instructions.
•• Always have at least two people mount the product on a wall.
•• Standard dimensions for wall mount kits are shown in the table below.
VESA screw hole specs (A * B) in millimeters
(inches)
Standard Screw
Quantity
400 × 400 (15.7 × 15.7)
M8
4
"" Do not install your Wall Mount Kit while your product is turned on. It may result in personal injury due to electric
shock.
14
Connecting to a network
•• Depending on how your network is configured, you may be able to attach your product to
your LAN by connecting the LAN port on the back of your product directly to a network wall
outlet using a LAN cable.
See the diagram below. Note that the wall outlet is attached to a modem or router
elsewhere in your house.
Network Settings (Wired)
LAN
The Modem Port on the Wall
RJ45
Connecting to a Wired Network
There are three ways to attach your product to your LAN using cable.
•• You can attach your product to your LAN by connecting the LAN port on the back of your
product to an external modem using a LAN cable.
See the diagram below.
LAN
External Modem
The Modem Port on the Wall
(ADSL / VDSL)
Modem Cable
RJ45
•• You can attach your product to your LAN by connecting the LAN port on the back of your
product to an IP Sharer which is connected to an external modem. Use LAN cable for the
connection. See the diagram below.
The Modem Port on the Wall
IP Sharer
(ADSL / VDSL)
(having DHCP server)
Modem Cable
LAN Cable
If you have a Dynamic Network, you should use an ADSL modem or router that supports
the Dynamic Host Configuration Protocol (DHCP). Modems and routers that support DHCP
automatically provide the IP address, subnet mask, gateway, and DNS values your product
needs to access the Internet so you do not have to enter them manually. Most home networks
are Dynamic Networks.
Some networks require a Static IP address. If your network requires a Static IP address, you
must enter the IP address, subnet mask, gateway, and DNS values manually on your product
Cable Setup Screen when you set up the network connection. To get the IP address, subnet
mask, gateway, and DNS values, contact your Internet Service Provider (ISP).
LAN Cable
External Modem
LAN Cable
LAN
If you have a Windows computer, you can also get these values through your computer.
"" You can use ADSL modems that support DHCP if your network requires a Static IP address.
"" ADSL modems that support DHCP also let you use Static IP addresses.
RJ45
LAN Cable
15
Set the network connection to use Internet services such as perform software upgrades.
Automatic Open Network Settings (Wired)
Connect to the network using a LAN cable.
How to set up manually
1 Set Network Type to Wireless from the Open Network Settings page.
2 The network test screen appears and the verification process starts. Press Cancel. The
verification process stops.
Make sure a LAN cable is connected first.
3 Select IP Settings on network connection screen. The IP Settings screen appears.
How to set up automatically
4 Select the field at the top, press E, and then set IP setting to Enter manually Repeat the
1 Set Network Type to Wireless from the Open Network Settings page.
entry process for each field in the IP Address.
2 The network test screen appears and verifies the network connection.
"" Setting IP setting to Enter manually automatically changes DNS setting to Enter
When the connection has been verified, the “Success! Your device is connected to the
Internet. If you have any problems using online services, please contact your Internet
service provider.” message appears.
"" If the connection process fails, check the LAN port connection.
"" If the automatic process cannot find the network connection values or if you want to set the
connection manually, go to the next section, network setup.
manually.
5 When done, select OK at the bottom of the page, and then press E. The network test
screen appears and the verification process starts.
6 When the connection has been verified, the “Success! Your device is connected to the
Internet. If you have any problems using online services, please contact your Internet
service provider.” message appears.
Manual Open Network Settings (Wired)
Offices may use static IP addresses.
If this is the case, ask the network administrator for the IP address, subnet mask, gateway and
DNS server address. Enter these values manually.
Getting the Network Connection Values
To view the Network connection values on most Windows computers, follow these steps.
1 Right click the Network icon on the bottom right of the screen.
2 In the pop-up menu that appears, click Status.
3 On the dialog that appears, click the Support tab.
4 On the Support Tab, click the Details button. The Network connection values are displayed.
16
Network Settings (Wireless)
Connecting to a Wireless Network
Wireless IP sharer
(router having DHCP server)
The LAN Port on the Wall
Automatic Network Setup (Wireless)
Most wireless networks have an optional security system that requires devices that access the
network to transmit an encrypted security code called an Access or Security Key. The Security
Key is based on a Pass Phrase, typically a word or a series of letters and numbers of a specified
length you were asked to enter when you set up security for your wireless network. If you use
this method of setting up the network connection, and have a Security Key for your wireless
network, you will have to enter the Pass Phrase during the the automatic or manual setup
process.
How to set up automatically
1 Set Network Type to Wireless from the Open Network Settings page.
2 The Network function searches for available wireless networks. When done, it displays a list
LAN Cable
Samsung recommends using IEEE 802.11n. When you play video over a network connection, the
video may not play smoothly.
of the available networks.
3 In the list of networks, press the ▲ or ▼ button to select a network, and then press the E
button twice.
"" Select a channel for the wireless IP sharer that is not currently being used. If the channel set
for the wireless IP sharer is currently being used by another device nearby, this will result in
interference and communication failure.
"" If the desired wireless router does not appear, select Refresh to search again.
"" Your product supports only the following wireless network security protocols.
If you select the Pure High-throughput (Greenfield) 802.11n mode and the Encryption type is
set to WEP, TKIP or TKIP AES (WPS2Mixed) on your AP or wireless router, Samsung products
will not support a connection in compliance with new Wi-Fi certification specifications.
4 If the Enter the password for (AP Name). screen appears, go to step 5. If you select a
"" If your wireless router supports WPS (Wi-Fi Protected Setup), you can connect to the
network via PBC (Push Button Configuration) or PIN (Personal Identification Number). WPS
will automatically configure the SSID and WPA key in either mode.
6 When done, use the right arrow button to move the cursor to Done, and then press E. The
"" Connection Methods: You can setup the wireless network connection in three ways.
Auto Setup (Using the Auto Network Search function), Manual Setup, Use WPS
"" If the router cannot be found after retrying, select the Stop button.
The Add Network button appears.
wireless router that does not have security, go to step 7.
5 If the router has security, enter the Enter the password for (AP Name). (Security key or PIN).
network connection screen appears and the verification process starts.
"" A connection with the router is established, but the Internet cannot be accessed.
7 When the connection has been verified, the “Success! Your device is connected to the
Internet. If you have any problems using online services, please contact your Internet
service provider.” message appears.
17
Manual Network Setup (Wireless)
How to set up manually
Offices may use static IP addresses.
1 Set Network Type to Wireless from the Open Network Settings page.
If this is the case, ask the network administrator for the IP address, subnet mask, gateway and
DNS server address. Enter these values manually.
Getting the Network Connection Values
To view the Network connection values on most Windows computers, follow these steps.
1 Right click the Network icon on the bottom right of the screen.
2 In the pop-up menu that appears, click Status.
3 On the dialog that appears, click the Support tab.
4 On the Support Tab, click the Details button. The Network connection values are displayed.
2 The Network function searches for available wireless networks. When done, it displays a list
of the available networks.
3 In the list of networks, press the u or d button to select a network, and then press the E
button twice.
"" If the desired wireless router does not appear, select Refresh to search again.
"" If the router cannot be found after retrying, select the Stop button.
The Add Network button appears.
4 If the Enter the password for (AP Name). screen appears, go to step 5. If you select a
wireless router that does not have security, go to step 7.
5 If the router has security, enter the Enter the password for (AP Name). (Security key or PIN).
6 When done, use the right arrow button to move the cursor to Done, and then press E. The
network connection screen appears and the verification process starts.
7 Select Cancel while network connections are being attempted. This will stop the
connection.
8 Select IP Settings on network connection screen. The IP Settings screen appears.
9 Select the field at the top, press E, and then set IP setting to Enter manually. Repeat the
entry process for each field in the IP Address.
"" Setting IP setting to Enter manually automatically changes DNS setting to Enter
manually.
10When done, select OK at the bottom of the page, and then press E. The network test
screen appears and the verification process starts.
11 When the connection has been verified, the “Success! Your device is connected to the
Internet. If you have any problems using online services, please contact your Internet
service provider.” message appears.
18
Use WPS
How to set up using Use WPS
If your router has a Use WPS button, follow these steps.
1 Set Network Type to Wireless from the Open Network Settings page.
2 Select Use WPS, press E, and then press E again.
3 Press the WPS or PBC button on your wireless router withine the next two minutes. Your
product automatically acquires all the network setting values it needs and connects to your
network.
4 The network connection screen appears, and network setup is done.
19
Chapter 03
Writing
What's a 'Roll'?
•• Files are called 'rolls' in this product. A 'roll' is a file with multiple pages linked together.
•• A roll can have up to 20 pages linked together.
•• Pages are linked vertically in portrait orientation, and horizontally in landscape orientation.
"" You can open only one roll on one screen. For more information, refer to 'Managing Rolls'.
Portrait orientation
Landscape orientation
Page 1
Page 2
Page 1
Page 2
20
Screen Elements
Import
Export
Buttons
Description
Import
View the screen of a mobile device or laptop connected to the product, or import
data such as images from a connected USB or network drive.
Export
Share your creations in various ways.
Manage and change the rolls and settings.
Move or edit the created rolls for each page.
Undo or redo the last action.
•• If any page editing actions such as page adding, deleting, and moving are
is reset.
found,
""
can be performed up to 20 times for each individual.
Page breaking line
Scroll the page breaking line to move the roll.
Bezel Scroll
Scroll the black area to move the roll.
21
Drawing / Erasing
Changing the pen colour
You can change the pen colour by touching and holding the screen with the pen.
You can freely use the supplied pen to write
anything you want.
•• Thin Tip (
•• Thick Tip (
): Pen Type
): Highlighter Type
"" To change the pen colour type, select
Changing pen thickness
→ Pen → Pen Colour or Highlighter Colour.
Erasing
You can use your finger or palm to erase your writing.
You can change the pen thickness.
"" Change the pen thickness at
→ Pen → Pen & Highlighter Thickness.
22
Managing Rolls
Buttons
Description
New
Create a new roll.
Open
Open, Delete, or Export a saved roll.
Save
Save the current roll.
Lock / Unlock
•• Lock: Press a four-digit password to lock the current roll.
•• Unlock: To Unlock a locked roll, press the four-digit password you set when locking the
roll.
"" Once unlocked, the current roll remains unlocked until it is locked again.
New
Open
Save
Lock
Delete
Blackboard
Delete
Delete the current roll.
Blackboard /
Whiteboard
Change the writing mode.
"" The roll you are editing is automatically saved and a new roll is opened.
Adjust the volume.
You can view How To Use.
You can see the configuration menu.
"" The displayed image may differ depending on the model.
23
Opening rolls
Deleting / Exporting rolls
→ Open → Select
→ Open
Select
Open
By name
By date
Select
Export
Delete
Cancel
"" The displayed image may differ depending on the model.
"" The displayed image may differ depending on the model.
Select the desired roll.
You can select multiple rolls to export or delete.
Parts
Description
By name ↔ By date
Set the sort order of files.
Select
Select multiple rolls to export or delete.
File Name
Rename the file.
Parts
Export
Description
Share the selected rolls any way you like.
•• Email / USB / Network Drive
Delete
Delete the selected rolls.
Cancel
Deselect the roll.
"" To open a locked roll ( ), press the four-digit password.
"" The rolls are sorted by recent date.
24
Page Viewer
You can move or edit the created rolls for each page.
Parts
Description
Preview the roll.
"" The preview mode does not support the draw / erase function.
Close the page viewer.
Page number
Page viewer area
Displays the page number.
Displays the page you are currently viewing.
•• When you select a page, the focus is moved to it.
Import
Focus
Export
01
•• Drag on the Page viewer area to move to other page.
•• Touch and hold a page to open the page editing screen. On the page editing
screen, press and drag the desired page to change its page order.
Add a new page to the focused position.
"" You can create up to 20 pages per roll.
02
Delete the focused page.
03
"" The displayed image may differ depending on the model.
25
Chapter 04
Import
You can view the screen of a mobile device or laptop connected to the product, or import data
such as images from a connected USB or network drive.
•• Touch Import at the top of the screen to select the desired device.
"" You can capture the screens you want from the imported content.
Icons
Description
Displays the screen from a mobile device by using Smart View or Screen
Mirroring function.
Displays your laptop screen imported using HDMI connection or WiFi display.
Import
Mobile
Laptop
Import
Displays images and dedicated files (.iwb) imported from a connected USB
device.
USB
Export
"" The displayed image may differ depending on the model.
Network Drive
Displays images and dedicated files (.iwb) imported from a connected network
drive.
"" Dedicated files (extension: iwb) are files created and saved by this product and are only
available on the FLIP model.
"" Supportable image file formats: JPG, BMP, PNG, MPO
26
Connecting to a Mobile Device
Import → Mobile
Connecting using Smart View or Screen Mirroring
Connecting using NFC tagging
"" This function is supported only on Android 8.0 Oreo version or later of Samsung mobile
devices.
"" In writing mode, an NFC tagging can automatically perform Smart View or Screen Mirroring
on your mobile device.
Smart View
1 Turn on the NFC feature on a supported mobile device.
1 Drag down the top bar on the mobile device screen to start Smart View or Screen Mirroring.
2 Select this product from the list of devices displayed on the screen.
2 Tag the mobile device to the NFC pad at the side of the product.
"" You can control the mobile device from the product screen.
–– The initial device name is [Flip] Samsung WMH Series.
"" You can control the mobile device from the product screen.
"" HDCP-encrypted content may not be visible when connected.
27
Connecting to a Laptop
Connecting via the WiFi Display function
"" This function is only available for the laptops that support the WiFi Display function.
Import → Laptop
Import
Mobile
Laptop
USB
Network Drive
Laptop
STEP. 02
HDMI
STEP. 01
Wireless
"" The displayed image may differ depending on the model.
Connecting using a cable
1 Select Action Center or Devices in the taskbar notification area of the laptop.
1 Connect the product to the laptop using an HDMI cable.
2 Click Connect or Project and select a [Flip] Samsung WMH Series device to complete the
"" HDCP-encrypted content may not be visible when connected.
HDMI
connection.
"" The connection procedure may vary depending on the laptop.
"" After the WiFi Display connection is made, you can control the laptop screen from the
product screen.
"" This function is only supported by Windows 8.1 and Windows 10.
2 Select Import → Laptop → HDMI from the top of the screen.
3 To control the laptop from the product screen, connect the supplied USB cable to the
TOUCH OUT port on the product.
"" This function is supported only when the laptop screen is in both landscape orientation and
the full screen mode.
TOUCH OUT
28
Importing from a USB Device
Importing from a Network Drive
Import → USB
Import → Network Drive
Import
Import
Mobile
Laptop
USB
Network Drive
USB
Mobile
Laptop
USB
Network Drive
Network Drive
USB1
USB2
USB3
USB4
USB5
USB6
NETWORK1
NETWORK2
Add
"" The displayed image may differ depending on the model.
"" The displayed image may differ depending on the model.
Connect an external HDD or a USB storage device.
Connect the network drive to bring files.
"" You can import only images and dedicated files (.iwb).
"" You can register a network drive while the network is connected.
For information about how to connect to a network, see 'Connecting to a network'.
"" You can register a network drive account at
→ Connect → Advanced Settings → Network
Drive → Add Account.
To register a network drive account, you must enter the Address, Username, and Password.
To register your network drive account, refer to 'Add Account' for Network Drive.
"" You can import only images and dedicated files (.iwb).
29
Source Window
When you connect a laptop or a mobile device to the product, the source window appears.
"" This function is available only in the writing mode.
Parts
Device name
Description
Menu bar
Drag the source window to move to the desired position.
Device name
Displays the name of the connected device.
Capture the source window.
Rotate the source window.
"" This function is supported only on Android 8.0 Oreo version or later of Samsung
mobile devices.
Switch to the full screen mode.
•• When the power button is pressed on the full screen mode, the screen returns to
the original mode.
"" When the product is in portrait orientation, the full screen mode is supported
only on the Android 8.0 Oreo version or later of Samsung mobile devices.
"" The displayed image may differ depending on the model.
"" The full screen mode for the laptop is only supported in the landscape
orientation.
Close the source window.
Adjust the size of the source window.
30
Chapter 05
Export
You can export your created rolls in various ways.
Icons
Description
Send your created rolls via email.
Export
Print your created rolls.
Email
Print
Import
USB
Export
Network Drive
Export your created rolls to a connected USB device.
Export your created rolls to a registered and connected network drive.
"" The displayed image may differ depending on the model.
31
Sending Email
To send your created rolls via email, first register your email account.
"" You can register your email account at
"" If you set Sender Authentication to Use at
→ Connect → Advanced Settings → Email, you must authenticate
your account each time you send an email. See below.
–– When Sender Authentication is set to Use, anyone who has a mail account on the same mail server (SMTP
Server Name, SMTP Port Number) can send emails.
But every time they send an email, they must enter their Account and Password.
Export → Email
Email
Send
To
*****@***. ***
Subject
[[Flip] Samsung WMH Series] ****-**-**, **:**
→ Connect → Advanced Settings → Email.
–– When Sender Authentication is set to Don't Use, you can send emails only with the Account and Password
registered in the product.
–– For the SMTP information required to register a mail server, contact your mail server administrator.
"" Files saved as dedicated files are converted to .pdf files and sent.
Parts
1
Description
Enter the recipient's email address.
To
•• Press
and type text by using the virtual keyboard.
•• Press
on the virtual keyboard to enter text by handwriting.
•• To enter an email address automatically, tag an NFC card that has that email
address entered.
""
: Explains where to tag the NFC tag.
"" Using the NFC Writing App, register an email address with the NDEF Standard
<Text> Record Type to an NFC Forum Type 2 Card sold on the market.
Subject
The email subject is automatically set to the device name and the current date.
Send
Send the email.
Change the page view mode for the roll to send.
Select the pages to send.
2
"" The displayed image may differ depending on the model.
32
Printing
Installing Flip Printing Software
Follow the onscreen instructions to install Flip Printing Software.
To print, you must set up the Print Server and the Clock Set.
To set up the Print Server, the product and the printer you want and your PC must be connected
to the same network.
"" The installation takes about 10 minutes, and the time taken may vary depending on your PC
environment.
Flip Printing Software must be also installed on the PC connected.
PC installation requirements
"" For information about how to connect to a network, see 'Connecting to a network'.
•• Supported operating systems:
Windows 7(32/64 bit), Windows 10(32/64 bit), MAC
"" You can set up the Print Server at
"" You can set Clock Set at
→ Connect → Print Server.
→ System → Time → Clock Set.
"" The Flip Printing Software is available on its website
– http://displaysolutions.samsung.com
– http://www.samsung.com
"" Devices that transfer files, such as virtual printers (PDF, XPS, One note, etc.) or fax
machines, are not supported, but only printers that can print actual paper are supported.
"" For print paper size, only A4 is supported.
"" When installing the software, make sure that critical Windows updates are already
installed. Update Windows Update to the latest version before beginning the setup.
"" For Windows 7, make sure that Service Pack 1 is already installed.
Setting up the printer
After the Flip Printing Software is installed, make the following settings on the product
onscreen menu.
Setting up automatically
1 Select
→ Connect menu.
2 Select Print Server → Connect to Server → Auto.
Setting up manually
1 Select
→ Connect menu.
2 Select Print Server → Connect to Server → Manual, and then enter the Server IP address of
the PC where Flip Printing Software is installed.
33
Export → Print
Parts
Print
Print
Printer
01
Copies
Colour Mode
1
Description
Printer
Displays a list of connected printers. Select a printer to print the roll with.
Copies
Set the number of prints.
Print preview area
Preview the roll to print.
Print
Start the printing.
Colour Mode
Select the colour to print the roll with.
Change the page view mode of the roll to print.
Select the pages to print.
2
"" The displayed image may differ depending on the model.
34
Exporting to a USB Device
Exporting from a Network Drive
Export → USB
Export → Network Drive
Export
Email
Export
Print
USB
Network Drive
USB
Save
USB1
USB2
USB3
USB4
USB5
USB6
Email
Print
USB
Network Drive
NETWORK1
Network Drive
Save
NETWORK2
Add
"" The displayed image may differ depending on the model.
"" The displayed image may differ depending on the model.
Connect an external HDD or a USB storage device.
Connect the network drive to save files.
"" You can save only the .iwb and .pdf file.
"" You can register a network drive while the network is connected.
For information about how to connect to a network, see 'Connecting to a network'.
"" You can register a network drive account at
→ Connect → Advanced Settings → Network
Drive → Add Account.
To register a network drive account, you must enter the Address, Username, and Password.
To register your network drive account, refer to 'Add Account' for Network Drive.
"" You can save only the dedicated files (.iwb).
35
Chapter 06
Menu
Pen
2nd
3rd
Description
Pen & Highlighter Thickness
Adjust the thickness of the pen and the highlighter. The highlighter is available by using the end of a supported pen.
Pen Colour
Select the colour palette for the normal pen.
Highlighter Colour
Select the colour palette for the highlighter. The highlighter is available by using the end of a supported pen.
36
Connect
2nd
3rd
Network
Description
Configure your device's network.
Network Status
View your current network and internet status.
Open Network Settings
Configure network settings to connect to an available network.
Proxy server
Set up your proxy server connection and related functions.
Device Connection Manager
Allow devices, like smartphones and tablets, on your network to share content with your product.
Access Notification
Display a notification when a device, such as a smartphone or tablet, is connected. If you use a Wi-Fi network that requires a
password, turn Off this option to automatically connect with devices without viewing notifications.
Device List
View and manage connected devices.
37
2nd
3rd
Description
Advanced Settings
Email
Set up an email account for sending emails.
"" For more information, refer to 'Sending Email'.
LDAP
•• Set LDAP Connection
Configure a new LDAP connection.
–– Use LDAP: Whether or not to use LDAP
–– Import Setup Value: Can fetch the following settings from LDAPConnectionConfig.txt stored on the USB(Password
excluded)
"" For more information, refer to 'How to create a text file for use of LDAP '.
–– User ID: DN(Distinguished Name) of the User ID that is used in the LDAP server.
––
––
––
––
––
"" The format of User ID complies with the DN format of LDAP.
e.g. cn=admin, dc=myldap, dc=com
Password: Password that is used for authentication of the LDAP server
Server Address: IP or URL of the LDAP server
Server Port Number: Port number of the LDAP server
Base DN: Top DN that is to be used for search in the DIT(Directory Information Tree) when connecting the LDAP
SSL/TLS: Whether or not to use SSL/TLS
"" When SSL/TLS is set to be Use, the encrypted data communication is enabled.
–– Use Untrusted Certificates: Whether or not to allow untrusted certificates
–– Authentication Type: Select Basic or Anonymous for authentication of the corresponding LDAP server.
38
2nd
3rd
Description
Advanced Settings
LDAP
•• LDAP Query Configuration
Set the query for the connected LDAP.
––
––
––
––
––
––
––
UID: Change the user UID that is used in LDAP.
Email: Change the Email that is used in LDAP.
Name: Change the user name (common name) that is used in LDAP.
Last Name: Change the surname of the user that is used in LDAP.
Company name: Change the company name that is used in LDAP.
Department: Change the department name that is used in LDAP.
Custom Query: Fetches the user defined query from LDAPQuery.txt (case sensitive) stored on the USB.
"" For more information, refer to 'How to create a text file for use of LDAP '.
"" Press the Reset button to restore the settings to the factory defaults.
"" When the mapping does not match, the search result does not include the attributes.
39
How to create a text file for use of LDAP
The LDAP configuration basically consists of many long sentences.
During LDAP configuration, FLIP can be fetched using the text file to prevent typos and make a
batch setting.
"" Input of file name and content should be case sensitive for correct operation.
•• Format of LDAPConnectionConfig.txt
(1)Example of the text file
User ID=cn=Manager, dc=example, dc=com
Server Address=123.456.789.012
Server Port Number=12345
Base DN=dc=samsung, dc=example, dc=com
SSL/TLS=Don't Use
Use Untrusted Certificates=Don't Use
Authentication Type=Basic
(2)Allocation of values (VAL) for each key
User ID: Enter the User ID.
Server Address: Enter the IP or URL of the LDAP server.
Server Port Number: Enter the Port of the LDAP server.
SSL/TLS: Enter Use or Don't Use.
Use Untrusted Ceritificates: Enter Use or Don't Use.
Authentication Type: Enter Basic or Anonymous.
•• Format of LDAPQuery.txt
(1)Example of the text file
Col=mail
Col=cn
Col=departmentNumber
Col=o
Query=(|(mail=*<A>*)(cn=*<A>*))
(2)Allocation of values (VAL) for each key
1)Col part
‒‒In most cases, the above five rows are used and they are sequentially mapped to
email, name, level, department and company.
‒‒Each row is mapped based on the following grammar. Col is each attribute in LDAP
and VAL is the value mapped in LDAP Query Configuration.
Col is the name shown on the left in LDAP Query Configuration and VAL is the
attribute displayed on the right in the LDAP Query Configuration menu.
Col=VAL or Col=VAL+VAL
‒‒You can select the value of the desired column (Col) and change it.
‒‒Col=level indicates the title. It does not appear on the menu but it is used to display
the search result.
2)Query part
‒‒<A> is the Keyword that is used for a Search.
‒‒The syntax for the Custom Query complies with the LDAP Query rule excluding <A>.
For example, when <A> is included in the mail or cn attribute, you can create it as
follows.
Query=(|(mail=*<A>*)(cn=*<A>*))
40
2nd
3rd
Description
Advanced Settings
Print Server
Set up the Print Server to use the printing function.
"" For more information, refer to 'Printing'.
•• Connect to Server
–– Auto: View and select one from a list of server IP addresses of the PCs where Flip Printing Software is installed,
available on the network.
–– Manual: Enter the Server IP address of the PC where Flip Printing Software is installed.
Network Drive
Add or edit network drive accounts. You can only add network drives by using Samba.
•• Add Account: Add new network drive accounts. Only Samba can be added to the network drive.
"" SAMBA 2.0 or later is supported. If you cannot connect to the network drive, update SAMBA to the latest version.
"" To register a network drive account, you must enter the Address, Username, and Password.
–– Address: //computer IP address/shared folder name
"" When entering an address, be sure to use / instead of ₩
and \.
For example, if you share a folder named "sharedfolder" on
a PC with IP address of 12.34.56.789, enter "//12.34.56.789/
sharedfolder" as the address.
–– Username: A Windows account with permissions to the shared
folder
"" When entering a domain, be sure to use ₩ or \.
For example, DomainName₩WindowsAccount
–– Password: The password you set for your Windows account
Add Account
Address
//12.34.56.789/sharedfolder
Username
DomainName\WindowsAccount
Password
********
Save
Cancel
•• Edit Account: Edit network drive accounts.
41
System
2nd
3rd
Description
Language
Change your Language settings.
Time
Configure various time-related settings.
Clock Set
Set current date and time.
DST
Adjust clock for Daylight Saving Time.
"" Start Date, End Date and Time Offset are enabled only when DST is set to On.
Smart Security
Change PIN
Security provided to protect your display device and connected storage devices against viruses includes.
Scan
Inspect your display device and connected storage devices to check for viruses.
Isolated List
Check the list of items that have been isolated they contain viruses.
Change the 4-digit password required to use the Advanced Settings functions and the Reset All function.
"" The default PIN number is 0000.
Device Name
Enter Device Name.
You can find this name on the device being used over the network.
42
2nd
3rd
Advanced Settings
Description
Configure advanced settings which includes USB Lock, Network Lock, Delete All Files, etc.
Enter your 4 digit PIN number. The default PIN number is "0000".
"" If you want to change the PIN number, use the Change PIN function.
Screen Saver
Set up the Screen Saver. You can select an image to use as the Screen Saver.
USB Lock
Set up a USB Lock. After setting up, the device will be restarted to apply the settings.
Network Lock
Set up a Network Lock. After setting up, the device will be restarted to apply the settings.
Auto Save & Auto Power Off
•• Auto Save: Automatically save all data. To use Auto Power Off, Auto Save must be enabled first.
•• Auto Power Off: Choose how the display will stay on before turning off after no user interaction is detected.
Motion Sensor
Set up a motion sensor to automatically shut down your product when no motion is detected over a certain period of time.
Delete All Files
Delete all data from the device, including locked data.
Period for Delete All
Set a reset interval at which all data on the internal storage will be deleted regularly.
Clone Product
Export this device's settings or import from other devices.
Start Setup
Go through the initial setup steps like you did the first time you used this product.
43
Picture
2nd
3rd
Description
Backlight
Adjust backlight brightness to suit your preference. 100 is the brightest setting.
Colour Temperature
It sets colour temperature. The value and temperature increase simultaneously, so the ratio of blue colour rises.
(Range: 2800K - 16000K)
White Balance
HDMI Black Level
R-Offset / G-Offset / B-Offset
/ R-Gain / G-Gain / B-Gain /
Reset
Adjust the colour temperature of the picture so that white objects appear brighter.
Adjust the black level to optimise the HDMI picture brightness and contrast.
"" This function is available only when the product is connected to a laptop using an HDMI cable and the Source window is
turned on.
Reset Picture
Restore all picture settings to the factory default.
44
Support
2nd
3rd
Software Update
Description
Update the software installed on your product.
Update now
Update software by downloading update files.
•• Current Version: This is the software version already installed in the product.
Contact Samsung
You can find information regarding our call centers and how to download products and software.
"" Contact Samsung and find the product Model Code and Software Version.
Reset All
It initializes all items in the total menu.
45
Chapter 07
Troubleshooting Guide
Problems and Solutions
"" Before calling Samsung Customer
Service Centre, test your product
as follows. If the problem persists,
contact Samsung Customer Service
Centre.
"" If the product is not turned on
or off when you operate the
buttons or motion sensor of the
product, you can turn it on or off
with the Samsung remote control
or Samsung remote control
application.
Source window (HDMI) issue
Blank spaces are found on all four sides of the screen when The blank spaces found on the screen have nothing to do with the product.
an HDMI cable is connected to the product and PC.
Blank spaces on the screen are caused by the PC or graphics card. To resolve the problem,
adjust the screen size in the HDMI settings for the graphics card.
If the graphics card settings menu does not have an option to adjust the screen size, update
the graphics card driver to the latest version.
(Please contact the graphics card or computer manufacturer for further details about how to
adjust the screen settings.)
The images on the screen look distorted.
Check the cable connection to the product.
The screen is not clear. The screen is blurry.
Set the resolution and frequency to the recommended level.
The screen appears unstable and shaky.
Check that the resolution and frequency of the PC and graphics card are set within a range
compatible with the product. Then, change the screen settings if required by referring to
'Preset Timing Modes'.
There are shadows or ghost images left on the screen.
46
Source window (HDMI) issue
White does not really look white.
Go to Picture and adjust the White Balance settings.
The product will turn off automatically.
Make sure the power cable is connected properly to the product and power outlet.
The screen display does not look normal.
Encoded video content may cause the display to appear corrupted in scenes featuring fast
moving objects such as in a sports event or action video.
Low signal level or low picture quality may cause the display to appear corrupted. This does not
mean the product is defective.
A cell phone within a distance of one-meter radius may cause static on analogue and digital
products.
The brightness and colour do not look normal.
From the menu, select Support → Reset All to try resetting the screen.
The display looks unstable and then freezes.
The screen may freeze when a resolution other than the recommended resolution is used or
if the signal is not stable. To resolve the issue, change the PC resolution to the recommended
resolution.
The screen cannot be displayed in full screen.
If the source window is set to full screen mode while in portrait orientation, a black bar appears
at both the top and bottom.
Change to landscape orientation, and then switch the Source window to full screen mode.
47
Sound issue
There is no sound.
Check the volume.
The volume is too low.
Adjust the volume.
If the volume is still low after turning it up to the maximum level, adjust the volume on your PC
sound card or software programme.
Video is available but there is no sound.
If an HDMI cable is connected, check the audio output settings on the PC.
If a source device is used
•• Check the audio output settings for the source device.
(For example, if your monitor is connected to HDMI, you may need to change the audio
option of your video output device to HDMI.)
Reconnect the power cable to the device and then reboot the device.
There is static coming from the speakers.
Low signal level can cause corrupted sound.
There is audible sound when the volume is muted.
Audio settings for main speakers are separate from the internal speakers on the product.
Changing or muting the volume on the product does not affect an external amplifier(decoder).
48
Touch function issues
The icons can be touched but the drawings cannot.
Use the provided product-specific pen.
Drawing and erasing do not work when the Source window
is open.
In the PIP mode, the drawing function is not supported within the Source window. In the source
window, drawings in a PC application such as Paint are made by that PC application.
Touching does not work when HDMI connection is used.
When the product is connected to a PC, make sure that the PC screen is in the full screen mode
(landscape).
Check whether the TOUCH OUT port on the product is connected to a USB port on the PC using
a USB cable.
I use two pens, but they do not work well.
Make sure that there is enough space between the two pens at multi-touching.
Touches break, reaction speed gets slow, and so on.
Make sure that there are no foreign substances on the screen surface.
Check whether the screen is broken.
Make sure that the product is not exposed to direct sunlight.
49
Other issue
The product smells like plastic.
The plastic smell is normal and disappears over time.
Small particles are found on the edges of the product.
The particles are part of the product design. The product is not defective.
When I try to change the PC resolution, a message "The
defined resolution is not supported." appears.
The message "The defined resolution is not supported." appears if the input source resolution
exceeds the maximum resolution of the product.
To resolve the issue, change the PC resolution to a resolution supported on the product.
There is no sound from the speakers in HDMI mode when a
DVI-HDMI cable is connected.
DVI cables do not transmit sound data.
HDMI Black Level is not functioning properly on an HDMI
device with YCbCr output.
This function is available only when a source device, such as a DVD player and STB, is
connected to the product via an HDMI (RGB signal) cable.
There is no sound in HDMI mode.
Displayed picture colors may not look normal. Video or sound may not be available. This can
occur if a source device that only supports an older version of the HDMI standard is connected
to the product.
50
Chapter 08
Specifications
General
"" Horizontal Frequency
The time required to scan a single
line from the left to the right side
of the screen is called a horizontal
cycle. The reciprocal number of a
horizontal cycle is called horizontal
frequency. Horizontal frequency is
measured in kHz.
"" Vertical Frequency
The product displays a single image
multiple times per second (like a
fluorescent light) to display what
the viewer sees. The rate of a single
image being displayed repeatedly per
second is called vertical frequency
or refresh rate. Vertical frequency is
measured in Hz.
Model Name
Panel
Synchronization
Resolution
WM55H
Size
55 CLASS (54.6 inches / 138.7 cm)
Display area
1209.60 mm (H) x 680.40 mm (V) / 47.6 inches (H) x 26.8 inches (V)
Horizontal Frequency
30 - 81 kHz, 30 - 90 kHz (HDMI)
Vertical Frequency
48 - 75 Hz, 24 - 75 Hz (HDMI)
Optimum resolution
1920 x 1080 @ 60 Hz, 3840 x 2160 @ 30 Hz
Maximum resolution
1920 x 1080 @ 60 Hz, 3840 x 2160 @ 30 Hz
Power Supply
AC100-240V~ 50/60Hz
Refer to the label at the back of the product as the standard voltage can vary in different countries.
Environmental
considerations
Operating
Temperature : 0 °C – 40 °C (32 °F – 104 °F)
* For installing the housing, keep the internal temperature at 40 °C or below.
Humidity : 10% – 80%, non-condensing
Storage
Temperature : -20 °C – 45 °C (-4 °F – 113 °F)
Humidity : 5% – 95%, non-condensing
* Applicable before the product package is unpacked.
51
"" Plug-and-Play
This monitor can be installed and used with any Plug-and-Play compatible systems. Two-way data exchange between the monitor and PC system
optimizes the monitor settings. Monitor installation takes place automatically. However, you can customise the installation settings if desired.
"" Due to the nature of the manufacturing of this product, approximately 1 pixel per million (1ppm) may appear brighter or darker on the panel. This does
not affect product performance.
"" This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate
measures.
"" For detailed device specifications, visit the Samsung Electronics website.
52
Preset Timing Modes
"" This product can be set to only one resolution for each screen size to obtain the optimum picture quality due to the nature of the panel. Using a
resolution other than the specified resolution may degrade the picture quality. To avoid this, it is recommended that you select the optimum resolution
specified for your product.
The screen will automatically be adjusted if a signal that belongs to the following standard signal modes is transmitted from your PC. If the signals
transmitted from the PC differ from the standard mode, the screen may not be displayed. In such a case, change the settings as shown in the following table
by referring to the graphics card user manual.
Resolution
Horizontal Frequency
(kHz)
Vertical Frequency
(Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
IBM, 640 x 480
31.469
59.940
25.175
-/-
IBM, 720 x 400
31.469
70.087
28.322
-/+
MAC, 640 x 480
35.000
66.667
30.240
-/-
MAC, 832 x 624
49.726
74.551
57.284
-/-
MAC, 1152 x 870
68.681
75.062
100.000
-/-
VESA, 640 x 480
31.469
59.940
25.175
-/-
VESA, 640 x 480
37.861
72.809
31.500
-/-
VESA, 640 x 480
37.500
75.000
31.500
-/-
VESA, 800 x 600
35.156
56.250
36.000
+/+
VESA, 800 x 600
37.879
60.317
40.000
+/+
VESA, 800 x 600
48.077
72.188
50.000
+/+
53
Resolution
Horizontal Frequency
(kHz)
Vertical Frequency
(Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
VESA, 800 x 600
46.875
75.000
49.500
+/+
VESA, 1024 x 768
48.363
60.004
65.000
-/-
VESA, 1024 x 768
56.476
70.069
75.000
-/-
VESA, 1024 x 768
60.023
75.029
78.750
+/+
VESA, 1152 x 864
67.500
75.000
108.000
+/+
VESA, 1280 x 720
45.000
60.000
74.250
+/+
VESA, 1280 x 800
49.702
59.810
83.500
-/+
VESA, 1280 x 1024
63.981
60.020
108.000
+/+
VESA, 1280 x 1024
79.976
75.025
135.000
+/+
VESA, 1366 x 768
47.712
59.790
85.500
+/+
VESA, 1440 x 900
55.935
59.887
106.500
-/+
VESA, 1600 x 900
60.000
60.000
108.000
+/+
VESA, 1680 x 1050
65.290
59.954
146.250
-/+
VESA, 1920 x 1080
67.500
60.000
148.500
+/+
CEA, 3840 x 2160
67.500
30.000
297.000
-/-
54
Chapter 09
Appendix
Responsibility for the Pay Service (Cost to
Customers)
"" When the service is requested, in spite of in warranty, we may charge you for a visit from a
service technician in the following cases.
Not a product defect
Cleaning of the product, Adjustment, Explanation, Re-installation and etc.
•• If a service technician is requested to give instructions on how to use product or simply
adjusts options without disassembling product.
•• If a defect is caused by external environmental factors (Internet, Antenna, Wired Signal,
etc.)
•• If a product is reinstalled or devices are connected additionally after installing the
purchased product for the first time.
•• If a product is reinstalled to move to a different spot or to move to a different house.
•• If the customer requests instructions on how to use another company's product.
•• If customer requests instructions on how to use the network or another company's
programme.
A Product damage caused by customer's fault
Product damage caused by customer's mishandling or wrong repair
If a product damage is caused by;
•• External impact or drop.
•• Use of supplies or separatly sold product unspecified by Samsung.
•• Repair from a person besides an engineer of outsourcing service company or partner of
Samsung Electronics Co., Ltd.
•• Remodeling or repairing the product by customer.
•• Using it with incorrect voltage or non-authorized electrical connections.
•• Not following the "cautions" in User Manual.
Others
•• If product fails by natural disaster. (lightning, fire, earthquake, flood damage, etc)
•• If consumable components are all used up. (Battery, Toner, Fluorescent lights, Head,
Vibrator, Lamp, Filter, Ribbon, etc.)
"" If customer requests a service in case the product has no defect, service fee may be
charged. So please read User Manual first.
•• If customer requests software installation and setup for the product.
•• If a service technician removes/cleans dusts or foreign materials inside of the product.
•• If customer requests an installation additionally after purchasing a product through homeshopping or online.
55
Prevention of Afterimage Burn-in
What is afterimage burn-in?
Afterimage burn-in should not occur when the panel is operating normally. Normal operation
refers to a continuously changing video pattern. If the panel displays a fixed pattern for an
extended period of time a slight voltage difference may occur between the electrodes in pixels
that control the liquid crystals.
Such a voltage difference between electrodes increases with time and makes the liquid
crystals thinner. When this occurs, a previous image can remain on the screen when the pattern
changes.
This information is a guide to prevent afterimage burn-in. Viewing a fixed screen
for an extended period of time may cause afterimage burn-in. This problem is not
included in warranty.
Licence
The terms HDMI and HDMI High-Definition Multimedia Interface, and
the HDMI Logo are trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other countries.
Open Source Licence Notice
In the case of using open source software, Open Source Licences are available on the
product menu. Open Source Licence Notice is written only English.
For information on the Open Source Licence Notice, contact the Samsung Customer Centre
or send email to oss.request@samsung.com.
Recommended prevention practices
Viewing a fixed screen for an extended period of time may cause afterimage burn-ins or
smudges. Turn off the product when it is not used for a long time, activate the Power Saving
mode, or run a moving screen saver.
56
Download PDF