Samsung | MM-B3 | Samsung MM-B3 Benutzerhandbuch

MICRO COMPONENT
SYSTEM
CD-R/RW PLAYBACK
MM-B3/B4
Instruction Manual
Safety Warnings
Thank you for buying this
SAMSUNG micro-component system.
Contents
Please take time to read these instructions.
They will allow you to operate your
system with ease and take full advantage
of its features.
B
CLASS 1 LASER PRODUCT
This Compact Disc player is classified as a
CLASS 1 LASER product.
CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT
PRODUCTO LASER CLASE 1
Use of controls adjustments or performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
CAUTION-INVISIBLE LASER RADIATION
WHEN OPEN AND INTER LOCKS
DEFEATED, AVOID EXPOSURE TO BEAM.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
WARNING: TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE REAR COVER.
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
CAUTION: TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG TO
WIDE SLOT, FULLY INSERT.
This symbol indicates that dangerous voltage which can cause electric shock is
present inside this unit.
This symbol alerts you to important operating and maintenance instructions
accompanying the unit.
Wiring the Mains Power Supply Plug(UK Only)
SAFETY WARNINGS .................................................................................................................................................................................. 2
INSTALLING YOUR MICRO-COMPONENT SYSTEM
Front Panel View ........................................................................................................................................................................................4
Remote Control ..........................................................................................................................................................................................5
Rear Panel View ........................................................................................................................................................................................6
Where to Install Your Micro-Component System ......................................................................................................................................7
Connecting your System to the Power Supply ..........................................................................................................................................7
Inserting Remote Control Batteries ............................................................................................................................................................7
Connecting to an External Source ............................................................................................................................................................8
Speaker Connection ..................................................................................................................................................................................8
Connecting the AM (MW)/LW Aerial ..........................................................................................................................................................9
Connecting the FM Aerial ..........................................................................................................................................................................9
Setting the Clock ......................................................................................................................................................................................10
CD-PLAYER
Listening to a Compact Disc ....................................................................................................................................................................10
Selecting a Track ....................................................................................................................................................................................10
Searching for a Specific Music Passage on a CD ..................................................................................................................................10
CD Repeat Function ............................................................................................................................................................................11
Repeat A
B Function ....................................................................................................................................................................11
Programming the Order of Playback ................................................................................................................................................11
Regarding the playback of CD-R/RW ......................................................................................................................................................11
Checking or Changing Programmed Tracks ..........................................................................................................................................12
TUNER
Searching for and Storing the Radio Stations..........................................................................................................................................12
Selecting a Stored Station........................................................................................................................................................................13
Improving Radio Reception ......................................................................................................................................................................13
TAPE DECK
Listening to a Cassette ............................................................................................................................................................................14
Selecting the Cassette Playback Mode (Option) ......................................................................................................................................14
Tape Counter ..........................................................................................................................................................................................14
Recording a Compact Disc ......................................................................................................................................................................15
Recording a Radio Program ....................................................................................................................................................................15
IMPORTANT NOTICE
The mains lead on this equipment is supplied with a moulded plug incorporating a fuse. The value of the fuse is indicated on the pin face
of the plug and, if it requires replacing, a fuse approved to BS1362 of the same rating must be used.
Never use the plug with the fuse cover omitted. If the cover is detachable. If a replacement fuse cover is required, it must be of the same
colour as the pin face of the plug. Replacement covers are available from your dealer.
If the fitted plug is not suitable for the power points in your house or the cable is not long enough to reach a power point, you should obtain
a suitable safety approved extension lead or consult your dealer for assistance.
However, if there is no alternative to cutting off the plug, remove the fuse and then safely dispose of the plug. Do NOT connect the plug to
a mains socket as there is a risk of shock hazard from the bared flexible cord.
IMPORTANT
The wires in the mains lead are coloured in accordance with the following code:–
BLUE = NEUTRAL
BROWN = LIVE
OTHER FUNCTIONS
Mute Function ..........................................................................................................................................................................................15
Timer Function ........................................................................................................................................................................................16
Canceling the Timer ................................................................................................................................................................................16
Power sound function ..........................................................................................................................................................................17
Sleep Timer............................................................................................................................................................................................17
S.Bass (Super Bass) Function ..................................................................................................................................................................17
Selecting an Equalizer Preset ..................................................................................................................................................................17
Microphone Function (Option) ..............................................................................................................................................................18
Connecting Headphones ....................................................................................................................................................................18
RECOMMENDATIONS FOR USE
Safety Precautions ..................................................................................................................................................................................19
Cleaning Your Micro-Component System................................................................................................................................................19
Precautions When Using Compact Discs ................................................................................................................................................20
Precautions When Using Audio Cassettes ..............................................................................................................................................20
Before Contacting the After-Sales Service ..............................................................................................................................................20
Technical Specifications ..........................................................................................................................................................................21
As these colours may not correspond to the coloured markings identifying the terminals in your plug, proceed as follows:–
The wire coloured BLUE must be connected to the terminal marked with the letter N or coloured BLUE or BLACK. The wire coloured
BROWN must be connected to the terminal marked with the letter L or coloured BROWN or RED.
WARNING:
2
DO NOT CONNECT EITHER WIRE TO THE EARTH TERMINAL WHICH IS MARKED WITH THE LETTER E OR BY
THE EARTH SYMBOL
, OR COLOURED GREEN OR GREEN AND YELLOW.
Symbols
Press
Push
Important
Note
3
GB
Front Panel View
Remote Control
B
GB
On/Standby
7
Push Open
EQ Preset
2
EQ
TUNER
CD
TAPE
AUX
Band
Power
Sound
Down
Tuning Mode
Up
REC/Pause CD Sync.
Counter
Reset
Repeat
A B
3
4
9
10
11
12
13
Sleep
Power
Sound
Program
/Set
CD Repeat Mono/ST.
AUX
11
11
12
TUNER
13
13
Band
14
14
15
16
16
TAPE
6
7
CD
17
18
18
VOL.
14
15
5
6
4
Mute
22
3
44
55
8
S.Bass
Timer/
Clock
9
10
1
Volume
Timer
On/Off
1
CD
8
Push Eject
Tuning
Mode
19
19
CD
VOL.
20
20
16
1.
On/Standby
9.
EQ
2.
Function selection
10.
S. Bass
(TUNER/CD/ TAPE/AUX)
11.
Power Sound
3.
Skip or Search
12.
Counter Reset
4.
Stop
13.
Mute
5.
REC/Pause
6.
7.
8.
CD Sync.
CD Push Open
Volume control
14.
15.
CD Repeat/REV. Mode(OPTION)
TAPE/CD Repeat A
B
16.
Push Eject (Cassette Door Open/Close)
1.
On/Standby
11.
AUX
2.
EQ Preset
12.
Program/Set
3.
Power Sound
13.
TUNER/Band
4.
Sleep
5.
CD Repeat
14.
15.
Mono/Stereo
Tape Play
6.
Tape rewind and fast-forward
16.
Tape Stop
7.
CD Stop
17.
CD Play
8.
Skip or Search
18.
Volume increase
9.
Timer/Clock
19.
Tuning Mode
10. Timer on/off
20.
Volume decrease
5
Where to Install Your
Micro-Component System
Rear Panel View
Inserting Remote Control Batteries
GB
B
To take full advantage of your new micro-component system, follow these installation instructions before connecting the unit.
1
2
Install the system on a flat, stable surface.
Never place this unit on carpeting.
Never place this unit in an outdoor area.
Maintain an open space of approximately 6 inches (15 cm) on the
sides and rear of the system, for ventilation purposes.
Make sure that you have enough room to open the compact disc
compartment easily.
Place the loudspeakers at a reasonable distance on either side of
the system to ensure good stereo sound.
Direct the loudspeakers towards the listening area.
For optimum performance, make sure that both speakers are placed
at an equal distance above the floor.
ANTENNA
3
EQ
CD
When replacing the batteries, use a new set of batteries and
never mix alkaline and manganese batteries.
1
Place your thumb on the position marked
on the battery
compartment cover (rear of the remote control) and push the cover in
the direction of the arrow.
2
Insert two AAA, LR03 or equivalent batteries, taking care to respect
the polarities:
+ on the battery against + in the battery compartment
– on the battery against – in the battery compartment
3
Replace the cover by sliding it back until it clicks into position.
If you will not be using the remote control for a long time,
remove the batteries to prevent corrosion.
Volume
TUNER
Insert or replace remote control batteries when you:
Purchase the micro-component system
Find that the remote control is no longer operating correctly
S.Bass
TAPE
AUX
Band
Power
Sound
Down
Tuning Mode
Up
REC/Pause CD Sync.
Mute
Counter
Reset
Repeat
A B
Push Eject
4
5
Connecting your System to the
Power Supply
6
The main lead must be plugged into an appropriate socket.
Before plugging your system into a main socket, you must check
the voltage.
AC CORD
1
Check the position of the voltage selector on the bottom of the
system (OPTION).
2
Plug the main lead (marked AC Cord on the rear of the system) into
an appropriate socket.
3
Press the On/Standby button to switch your micro-component system on.
1. MIC Jack Connector(optional)
3. FM Aerial Connector Terminal
4. AM Aerial Connector Terminal
1
220V-240V 110V-127V
2. Headphone Jack Connector
(Bottom)
5. AUX-Input
6. Loudspeakers Connector Terminals
AC CORD
2
(Rear)
6
7
Connecting to an External Source
Speaker Connection
Connecting the AM (MW)/LW Aerial
B
GB
The auxiliary input can be used to take advantage of the
sound quality of your micro-component system when listening
to other sources.
Examples: A television
A video disc player
A Hi-Fi stereo video cassette recorder
To connect the external source, the source must have an audio
output. In addition, you need an RCA connection cable.
1
Set the system to standby mode and disconnect it and the external
source from the main.
2
Connect the audio cable to the rear of the micro-component system.
The loudspeaker connector terminals are located on the rear
of the system (red and black tabs).
The AM aerial (for long and medium waves) can be:
Placed on a stable surface
Fixed to the wall (you must first remove the base)
The AM aerial connector terminals are located on the rear of the system and are marked AM .
There are four terminals on the system:
Two for the left speaker (marked L)
Two for the right speaker (marked R)
To avoid noise interference, check that the loudspeaker wires do not run close to the aerial wires.
Always keep them at least 2 inches (5 cm) away.
To achieve the correct sound quality, connect the:
Red wire to the + terminals
Black wire to the - terminals
(Right Speaker)
(Left Speaker)
ANTENNA
Connect the...
To the connector marked...
Red jack
White jack
R (right)
L (left)
ANTENNA
For optimum sound quality, do not invert the right and left
channels.
3
Plug the system back into the main socket and press On/Standby
(
) to switch it on.
4
Select the AUX source by pressing AUX.
Result: AUX is displayed.
5
6
Switch the external source on.
AC CORD
AC CORD
Adjust the volume and balance as required:
Volume
Equalizer
Connecting the FM Aerial
Example: You can watch a film and take advantage of stereo sound
provided that the original sound track is in stereo (as if you
were in a cinema).
There are two types of aerials, follow the instructions below (depending on option chosen).
1
How to connect a SCREW TYPE wire aerial.
The FM aerial connector terminals are located on the rear of the system and marked FM(300Ω).
Spread the T.form FM aerial out and attach the ends to a wall, in the position providing the best reception.
Directions in Installing Speaker
Installation in a place near heating apparatus, under direct lay of
light or with high humidity may cause performance degradation of
the speaker.
Do not install on the wall or on a high place of pole or other unstable place to prevent any safety accident caused by falling of the
speaker.
Do not take the speaker apart from TV or computer monitor.
The speaker near the TV or computer monitor may influence the
quality of the screen display.
Volume
EQ
TUNER
EQ
Up
S.Bass
AUX
Power
Sound
Mute
Counter
Reset
Repeat
A B
Push Eject
How to connect a COAXIAL TYPE aerial(OPTION).
Connect a 75Ω antenna to the FM aerial terminal.
Plug the connector on the FM aerial supplied into the coaxial socket (75Ω) marked FM (75Ω) on the rear of the system.
Follow the instructions given on Page 13 to tune into a radio station, and determine the best position for the aerial.
If reception is poor, you may need to install an outdoor aerial.
To do so, connect an outdoor FM aerial to the FM socket on the rear of the system, using a 75Ω coaxial cable (not supplied).
Volume
CD
TAPE
REC/Pause CD Sync.
2
TUNER
CD
Tuning Mode
Band
Down
S.Bass
TAPE
AUX
Band
Power
Sound
Down
Tuning Mode
Up
FM
FM
C
FM AERIAL 75Ω COAXIAL CABLE
(not supplied)
(supplied)
8
9
CD Repeat Function
Setting the Clock
Programming the Order of Playback
B
GB
Your system is equipped with a clock which allows you to
turn your system on and off automatically.
You should set the clock:
When you first purchase the micro-component system
After a power failure
After unplugging the unit
7
If it is desired to pause while the playback is processing, press the
CD(
) button.
Press the CD(
8
To stop playback, press the Stop (
3
4
Switch the system on by pressing On/Standby (
This feature can be combined with the CD Repeat function.
) button.
1
).
6
EQ
TUNER
CD
S.Bass
When you wish to stop the Repeat function, press CD Repeat a third time.
Result:REP is no longer displayed and the function is cancelled.
TAPE
Band
To...
Up
REC/Pause CD Sync.
Mute
CD Repeat Mono/ST.
Press Program/Set.
TUNER
1
Sleep
Power
Sound
Timer
On/Off
Selecting a Track
Program
/Set
AUX
CD
Tuning
Mode
To start playback at the beginning of the...
Press...
Next track
once
Current track
once
Previous track
twice
or
the
appropriate number of
times.
CD Repeat Mono/ST.
VOL.
CD
CD
4,6
4,6
VOL.
CD
Tuning
Mode
CD
CD
Repeat A
Press the CD(
)button on the main unit and select CD.
Open the CD door by pushing on the top of the main unit marked
Push Open ( ).
Result: The CD door is opened.
When listening to a compact disc, you can quickly search for a
specific music passage on a track.
To search through the tracks...
Close the CD door.
Result: Number of tracks and the total playback time are shown on
the display.
Press the CD(
1
Press CD(
) or TAPE button.
Result:The CD(TAPE) player starts playing.
2
Press Repeat A
B button.
Result:The indications appear: START
The flashes appear: A
B
A Time is memorized.
CD Repeat Mono/ST.
TUNER
4
TAPE
CD
6
1,7
VOL.
Press Repeat A
B button.
Result:The indications appear: END
B Time is memorized.
Your selected passages are repeated 3 times.
3
CD
Tuning
Mode
CD
3
VOL.
When you have finished the Repeat playback,
Press Repeat A
B.
for at least one second
EQ
TUNER
Backwards
CD
S.Bass
AUX
Tuning
Mode
Down
1
Tuning Mode
Up
1
Power
Sound
REC/Pause CD Sync.
Mute
Repeat
A B
VOL.
2,3,4
CD
CD
Regarding the playback of CD-R/RW
TAPE
for at least one second
It is recommended that you turn the volume down before using
this function.
CD
2,4
Sleep
AUX
Press and hold down...
Forwards
) button for playback.
Adjust the volume according to needs with the following procedures.
Press the VOL. + or – button.
Program
/Set
Power
Sound
Band
3
Searching for a Specific Music
Passage on a CD
B Function
Band
Place the CD on the compartment so that the CD label faces upward.
) twice to cancel the selection when the disc is playing.
When you select CD(TAPE) Repeat A
B playback, the music
passages to which you were listening are repeated 3 times.
VOL.
Do not use CDs of irregular shapes like heart or octagon shapes.
The performance of the player may be degraded.
Press Stop (
EQ Preset
Band
Listening to a Compact Disc
When you have finished selecting the tracks, press CD (
) to start
listening to the selection, in the order in which the tracks were
programmed.
You can select the track you wish to listen to, either when the
compact disc player is stopped or when a disc is playing.
VOL.
2
3,5,7
TUNER
7
CD
Timer/
Clock
To select other tracks, repeat Steps 3 and 4.
You can programme up to 24 tracks.
6
Band
When the correct time is displayed, press Program/Set.
Result: The clock starts and is displayed, even when the system is in
standby mode.
EQ Preset
10
4
TAPE
Track of your choice
5
6
Select the required track by pressing the SKIP buttons:
to move backwards through the tracks
to move forwards through the tracks
5
Sleep
Repeat
A B
When the correct hour is displayed, press Program/Set.
Result: The minutes flash.
On/Standby
3
4
Result:P -- 01 -- -- is displayed.
3
Result:P -- 02 -- -- is displayed.
Counter
Reset
8
Press...
).
Press Program/Set.
PROGRAM
Power
Sound
1, 5, 7
Tuning Mode
Down
To...
If necessary, stop the player by pressing Stop (
PROGRAM
Press...
You can display the time, even when you are using another
function, by pressing Timer/Clock once.
1
2
Once (REP. 1 is displayed)
Twice (REP. ALL is displayed)
AUX
Increase the minutes
Decrease the minutes
7
2
6
1
2
Press CD Repeat...
Current track indefinitely
Disc
6
Volume
Press Timer/Clock twice.
Result: CLOCK is displayed.
Increase the hours
Decrease the hours
5
Press the CD Repeat button.
To repeat the...
Press Program/Set.
Result: The hour flashes.
You can decide for yourself:
The order in which you listen to the tracks
The tracks to which you do not wish to listen
A specific track on a compact disc
All tracks on the compact disc
) button once again to play back again.
For each step, you have a few seconds to set the required
options. If you exceed this time, you must start again.
1
2
You can repeat:
Counter
Reset
In the case of an original CD-R(Recordable) recorded in
audio CD format, CD-RW(Rewritable) and editing by the
user, playback is processed on the respective
completed status. (The player may not be played back
according to the characteristics of the CD or recorded
status.)
The CD-RW is comparably less reflexive than CD which
causes more time delay to read.
VOL.
11
Searching for and Storing the Radio
Stations
Checking and Changing Programmed
Tracks
Searching for and Storing the Radio
Stations(continued)
Selecting a Stored Station
B
GB
You can check and change your selection of tracks at any time.
You must have selected at least one track.
1
2
Press Stop (
) once if you have started listening to the selection.
Press Program/Set.
You can store up to:
15 FM stations
8 MW station(OPTION)
7 LW station(OPTION)
5 MW station(OPTION)
5 SW1 station(OPTION)
5 SW2 station(OPTION)
6
15 AM stations(option)
15 AM stations(option)
Each time you press Program/Set, the next selection is displayed.
3
4
5
6
Press Program/Set one or more times until the track to be changed is
displayed.
Press
or
to select the new track.
Press Program/Set.
1
2
3
Press CD (
) to start listening to the selection.
Result: The first track selected is played.
You can change one or more tracks in your initial selection.
On/Standby
EQ Preset
Timer
On/Off
2,3,5
Sleep
CD Repeat Mono/ST.
TUNER
5
TAPE
CD
1
6
Select the TUNER function by pressing TUNER/Band on the front panel.
Select the required frequency band by pressing TUNER/Band again.
Result:The appropriate indication is displayed:
FM
Frequency Modulation
AM(MW)
Medium Wave
LW(Option)
Long Wave
SW1,SW2(Option)
Short Wave
7
1
2
3
4
Switch the system on by pressing On/Standby (
The PROGRAM function can be used to assign a new station to
an existing program number.
Press Tuning Mode one or more times until MANUAL is displayed.
Automatic tuning
Press and hold
or
on the remote control.
Press and hold
,
on the main unit.
Program
/Set
Power
Sound
EQ Preset
AUX
6
Sleep
CD Repeat Mono/ST.
Select the required frequency band by pressing TUNER/Band.
Select the radio station as follows.
To listen to ...
Press ...
A stored station
a Press the Tuning Mode button
until “PRESET” is displayed.
b Tuning
and
required station.
to select the
Press Tuning Mode again to exit the stored station selection
function.
On/Standby
TUNER
1
Power
Sound
EQ Preset
Band
).
Select the TUNER function by pressing TUNER/Band on the front panel.
To store any other radio frequencies required, repeat Steps 3 to 6.
Press
or
on the remote control.
Press
or
on the main unit.
Result: Press the button repeatedly to tune in the desired station
manually.
PRESET function is explained in detail in the section “Selecting a
Stored Station” on.
AUX
Band
).
Result: Automatically scans and tunes to the next available station.
Manual tuning
Timer/
Clock
Program
/Set
Power
Sound
4
Switch the system on by pressing On/Standby (
If you do not want to store the radio station found, revert to Step 4 and
search for another station.
Otherwise:
a Press Program/Set.
Result: The program number is displayed for a few seconds.
b Press Tuning
and
to assign a program number between 1
and 15.
c Press Program/Set to store the radio station.
Result: The program number is no longer displayed and the station is
stored.
You can listen to a stored radio station as follows:
Timer
On/Off
Timer/
Clock
Program
/Set
AUX
TAPE
Sleep
CD Repeat Mono/ST.
TUNER
2,3
CD
B d
Select the station to be stored by pressing
,
to increase or
decrease the frequency respectively.
To scroll through the frequencies faster when searching manually,
hold down the
,
.
The automatic search procedure may stop on a frequency that does
not correspond to a radio station.
If this happens, use the manual search mode.
VOL.
6
Tuning
Mode
CD
VOL.
CD
6
4
Tuning
Tuning
Mode
Mode
CD
VOL.
CD
CD
4
4
VOL.
VOL.
4
CD
Tuning
Mode
CD
4
Improving Radio Reception
1
Volume
VOL.
Volume
You can improve the quality of radio reception by:
Rotating the FM or AM(MW) aerial
EQ
EQ
TUNER
2,3
CD
S.Bass
TAPE
TUNER
CD
TAPE
Band
Power
Sound
Power
Sound
Tuning Mode
Up
REC/Pause CD Sync.
4,5
4
4,5
Testing the positions of the FM and AM(MW) aerials
before fixing them permanently
AUX
AUX
Band
Down
S.Bass
Mute
Repeat
A B
Down
Tuning Mode
Up
REC/Pause CD Sync.
Counter
Reset
6
6
Mute
Repeat
A B
Counter
Reset
If reception from a specific FM radio station is poor, press
Mono/ST to switch from stereo mode to mono. The quality of the
sound will be improved.
EQ Preset
Sleep
Power
Sound
Program
/Set
CD Repeat Mono/ST.
AUX
TUNER
Band
TAPE
12
13
Selecting the Cassette
Playback Mode (OPTION)
Listening to a Cassette
Recording a Compact Disc
Recording a Radio Program
B
GB
1
2
3
Switch the system on by pressing On/Standby (
Your micro-component system has three cassette playback
modes which enable you to listen to both sides of a cassette
automatically.
Press REV.Mode until the appropriate symbol is displayed.
).
Select the TAPE function by pressing TAPE on the front panel.
Open the cassette deck by pushing on the corner of the cover marked
Push Eject until you hear a click and then releasing it.
4
Insert the pre-recorded cassette with the open edge of the tape facing
downwards.
5
6
Close the deck by pushing on it until it clicks into place.
7
Press any of the following buttons during playback, as required.
When the display indicates... The micro-component system plays back...
One side of the selected cassette and then
stops.
Press the TAPE button.
Result: The cassette starts playing.
One side of the cassette.
The other side of the cassette and then
stops.
Both sides of the cassette indefinitely until
you press stop.
To...
Press...
Listen to the same track again
Listen to the next track
Listen to the previous track
Listen to the track of your choice
once
once
twice
the appropriate
or
number of times
/
once (option)
Listen to the other side of the cassette
You can record a compact disc on a cassette in two different ways:
Synchronised recording
Direct recording
Down
Tuning Mode
Up
REC/Pause CD Sync.
Mute
Counter
Reset
Repeat
A B
REV. Mode
Synchronised recording
1
2
3
4
5
6
Switch the system on by pressing On/Standby (
Load a compact disc.
Press the CD(
) button.
Use the CD selection (
,
) buttons to select the desired song.
Press the CD Sync. button on the front panel.
When stopped, press the button to start the recording from the
first piece of music.
1
2
3
4
Switch the system on by pressing On/Standby (
).
Insert a blank cassette in Deck.
Select the TUNER function by pressing TUNER/Band.
Select the radio station that you wish to record by pressing
or
button .
5
Press REC/Pause.
Result: REC is displayed and recording starts.
6
To stop recording, press Stop ( ) button.
To stop recording, press Stop ( ) button.
1
1
Volume
When the cassette is stopped, select one of the following functions as
required.
To...
Volume
Press...
EQ
TUNER
Tape Counter
Rewind the cassette
Fast-forward the cassette
Band
CD
The cassette player stops automatically when the beginning or
end of the cassette is reached.
To stop the playback or search, press Stop (
4
When playing a cassette, a counter is displayed to enable you to take
note of the counter value at the start of each track and thus start
playback at the beginning of the track to which you wish to listen.
) button.
The counter is only displayed when a cassette is being played.
Before starting to record a cassette for which you wish to take note of the
counter values at the beginning of each track, reset the counter by pressing
Counter Reset.
1
Volume
EQ
EQ
TUNER
CD
S.Bass
TUNER
CD
AUX
TAPE
AUX
Power
Sound
Tuning Mode
Up
Power
Sound
2,6
9
Tuning Mode
Up
REC/Pause CD Sync.
REC/Pause CD Sync.
7,8
Down
Mute
Counter
Reset
Repeat
A B
7,8
Mute
Repeat
A B
Counter
Reset
CD
3
Power
Sound
Tuning Mode
Up
4
6
S.Bass
TAPE
AUX
Mute
5
Band
Power
Sound
Down
Counter
Reset
Tuning Mode
Up
REC/Pause CD Sync.
Mute
Counter
Reset
5
Repeat
A B
6
4
4
Repeat
A B
Direct recording
Mute Function
The direct recording mode enables you to start recording
with any track on the compact disc.
You do not need to adjust the volume, as it has no effect on the recording.
You can turn the sound off temporarily on your system.
1
2
3
4
Switch your system on by pressing On/Standby (
Insert a blank cassette in Deck.
Load a compact disc.
5
Press the REC/Pause button.
Result: Recording will begin.
6
To stop recording, press Stop ( ) button.
Band
Band
Down
S.Bass
TAPE
TUNER
AUX
4
Down
EQ
S.Bass
TAPE
REC/Pause CD Sync.
9
).
Insert a blank cassette in Deck.
If there are very quiet passages on a track, the automatic search
function may stop before the end of the track. Also, a very short
silence between two tracks may not be detected.
8
You do not need to adjust the volume, as it has no effect on
the recording.
This feature enables you to synchronize the start of the
recording with the start of the disc or track of your choice.
You do not need to adjust the volume, as it has no effect on the recording.
Band
Power
Sound
You can record a radio program of your choice.
Press the CD(
) button.
Use the CD selection (
,
Example: You wish to answer a telephone call.
).
1
) buttons to select the desired song.
2
Press the Mute button.
Result: MUTE is displayed and the sound is switched off.
To switch the sound back on at the same volume as before,
press Mute again.
EQ
TUNER
CD
S.Bass
TAPE
AUX
3,5
Band
1
Power
Sound
Push Eject
Down
Tuning Mode
Up
REC/Pause CD Sync.
Mute
Counter
Reset
Volume
Repeat
A B
Band
TAPE
9
EQ
TUNER
7,8
CD
TAPE
AUX
CD
7,8
Band
4
Down
Tuning Mode
Power
Sound
Up
REC/Pause CD Sync.
6
14
S.Bass
5
Mute
Counter
Reset
Repeat
A B
15
Timer Function
S.Bass (Super Bass) Function
Power sound function
B
GB
This machine is equipped with the function of POWER SOUND,
which amplifies bass treble output to twice as much for powerful
real surround-sound.
The timer enables you to switch the system on or off at specific times.
Example: You wish to wake up to music every morning.
If you no longer want the system to be switched on or off
automatically, you must cancel the timer.
On/Standby
Before setting the timer, check that the current time is correct.
For each step, you have a few seconds to set the required
options. If you exceed this time,
you must start again.
4
5
Switch the system on by pressing On/Standby (
Press Timer/Clock until
).
1
Press the Power Sound button on the front panel.
P.SOUND is displayed for a few seconds.
Result:
A more powerful resonant sound is diffused.
Program
/Set
Sound
AUX
2
To cancel this function, press Power Sound again.
OFF is displayed for a few seconds.
Result:
Press the S. Bass button on the front panel.
Result: S. BASS is displayed.
2
To cancel this function, press S. Bass button again.
3,4,5,6,7
TUNER
Sleep
CD Repeat Mono/ST.
EQ
Press Program/Set.
Result:ON TIME is displayed for a few seconds, followed by any switchon time already set; you can set the timer switch-on time.
TUNER
Band
7
to select the source to be played when the
Insert a recorded cassette in the deck.
a Select the FM or AM frequency band by pressing
Tuning
and
.
b Press Program/Set.
c Select a preset station by pressing
Tuning
and
.
CD (compact disc) Load compact disc.
Press Program/Set to confirm the timer.
Tuning Mode
Up
CD
REC/Pause CD Sync.
Mute
Counter
Reset
EQ
TUNER
CD
Repeat
A B
VOL.
4,5,6,7
Power
Sound
Tuning Mode
Up
REC/Pause CD Sync.
Tuning
Mode
CD
Band
Down
Mute
Counter
Reset
Repeat
A B
CD
CD
4,5,6,7
VOL.
Selecting an Equalizer Preset
Sleep Timer
Cancelling the Timer
After having set the timer, it will start automatically as shown by
the
indication on the display. If you no longer wish to use the
timer, you must cancel it.
You can stop the timer at any time (system on or in standby mode).
To...
You can set the system to switch off automatically.
Example: You wish to fall a sleep to music.
1
Cancel the timer
Once.
Result:
is no longer displayed.
Restart the timer
Twice.
Result:
is displayed again.
Press Sleep on the remote control.
Result: The following indications are displayed:
Your micro-component system is equipped with a preset equalizer that allows you to choose the most appropriate balance
between treble and bass frequencies, according to the type of
music you are listening to.
Press EQ on the front panel or EQ Preset on the remote control until the
required option is selected.
2
Press Timer On/Off
Press Sleep one or more times to indicate how long the system should
continue playing before it switches off:
90 MIN
OFF
60 MIN
15 MIN
Press the button repeatedly to select
“ POP ➞ ROCK ➞ CLASSIC ➞PASS ”
45 MIN
30 MIN
At any time, you can:
Check the remaining time by pressing Sleep
Change the remaining time by repeating Steps 1 and 2
3
Press On/Standby to set the system to standby mode.
is displayed to the middle right of the time, indicating that the timer has
Result:
been set. The system will switch on and off automatically at the required
times.
Volume
To cancel the sleep timer function, press Sleep one or more times until
OFF is displayed and the word SLEEP disappears.
EQ
TUNER
CD
S.Bass
TAPE
AUX
Band
EQ Preset
Program
/Set
Power
Sound
AUX
Power
Sound
Down
Tuning Mode
Up
REC/Pause CD Sync.
If the timer switch on and off times are identical, the word ERROR
is displayed.
S.Bass
TAPE
AUX
You must also...
TAPE (cassette)
TUNER (radio)
Volume
Power
Sound
Set the timer switch-off time.
a Set the hour by pressing Tuning
and
.
b Press Program/Set.
Result: The minutes flash.
c Set the minutes by pressing Tuning
and
.
d Press Program/Set.
Result: VOL 10 is displayed, where 10 corresponds to the volume already set.
Press Tuning
and
system switches on.
S.Bass
TAPE
Band
Down
Press Tuning
and
to adjust the volume level and press
Program/Set.
Result:The source to be selected is displayed.
CD
AUX
TAPE
Set the timer switch-on time.
a Set the hour by pressing Tuning
and
.
b Press Program/Set.
Result: The minutes flash.
c Set the minutes by pressing Tuning
and
.
d Press Program/Set.
Result: OFF TIME is displayed for a few seconds, followed by any
switch-off time already set; you can now set the timer switch-off
time.
If you select...
1
TIMER is displayed.
6
8
Timer/
Clock
2
1,8
Power
EQ Preset
1
2
3
Timer
On/Off
Your Micro Component system has a bass amplification function
called S.Bass.
This function makes the sound more powerful and real.
On/Standby
Timer
On/Off
Timer/
Clock
Sleep
CD Repeat Mono/ST.
1,2,3
TUNER
Mute
Counter
Reset
Repeat
A B
Band
TAPE
EQ Preset
Power
Sound
Program
/Set
AUX
CD
Sleep
16
CD Repeat Mono/ST.
TUNER
17
Microphone Function (option)
Connecting Headphones
Cleaning Your
Micro-Component System
Safety Precautions
B
GB
The microphone enables the user to mix in his or her vocals
to sing-along with the music.
Preparation
Plug the microphone with a 3.5mm mic jack into microphone terminal.
You can connect a set of headphones to your micro
component system so that you can listen to music or radio
programs without disturbing other people in the room.
The headphones must have a 3.5 mm connector or
appropriate adapter.
The following diagrams illustrate the precautions to be taken
when using or moving your micro-component system.
Connect the headphones to the Phones connector on the rear panel
(or top right corner).
To obtain the best possible results from your
micro-component system, you must clean the following
elements regularly:
The outer casing
The compact disc player
The cassette players (heads, rollers and drive capstans)
Always unplug the system from the wall outlet:
Before cleaning it
If you are not going to be using it for a long time
Volume
Volume
EQ
TUNER
CD
TAPE
Tuning Mode
Up
S.Bass
AUX
Band
EQ
TUNER
CD
S.Bass
Power
Sound
TAPE
Down
AUX
REC/Pause CD Sync.
Band
Result: The loudspeakers are no longer used for sound output.
Counter
Reset
Mute
Power
Sound
Down
Tuning Mode
Up
REC/Pause CD Sync.
Repeat
A B
Counter
Reset
Mute
Repeat
A B
Push Eject
Push Eject
Prolonged use of headphones at a high volume may
damage your hearing.
Ambient operating conditions:
Ambient temperature
5°C-35°C
Humidity
10-75%
Do not expose the unit to direct sun
radiation or other heat sources.
This could lead to overheating and
malfunction of the unit.
Outer Casing
Clean the outer casing regularly using a soft cloth and a light detergent. Do
not use abrasive powders, liquids or aerosol cleaners. Never let any liquids
get into the system.
Compact Disc Player
1
Before playing a compact disc, clean it with a special CD cleaning
agent. Do not use the same cleaning agents as for vinyl LP records.
Carefully wipe the disc from the centre outward.
2
Regularly clean the player with a special cleaning disc (available
from your local dealer).
Volume
Volume
ANTENNA
EQ
TUNER
CD
S.Bass
TAPE
AUX
EQ
TUNER
CD
TAPE
Tuning Mode
Up
Band
S.Bass
Tape Decks
Power
Sound
AUX
Down
Tuning Mode
Up
REC/Pause CD Sync.
Band
Mute
Counter
Reset
Power
Sound
Down
REC/Pause CD Sync.
Mute
Repeat
A B
Counter
Reset
Repeat
A B
Push Eject
Push Eject
1
2
ANTENNA
Do not place potted plants or vases
on top of the unit. Moisture entering
the unit could lead to dangerous
electric shock and can cause
equipment damage. In such events
immediately disconnect the main
plug from the socket.
During thunderstorms, disconnect
the main plug from the socket.
Main voltage peaks due to lightning could damage the unit.
Press Push Eject(
) to open the cassette deck.
Use a cotton bud and a special cassette cleaning agent to clean the:
Head (1)
Rollers (2)
Drive capstans (3)
3
VOLUME
UP
1
2
DOWN
Remove the batteries from the
remote control, if not used for any
extended period.
Leaking batteries can cause serious
damage to the remote control.
When using headphones, take care
not to listen at excessive volumes.
Extended use of headphones at
high volumes will lead to hearing
damage.
If you will not be using the remote control for a long time,
remove the batteries to prevent corrosion.
Although your system is very hard-wearing, it should not be
used in an excessively dusty environment or subjected to
shocks or extreme heat (close to heating appliances or in
direct sunlight, etc.).
If the unit emits an unpleasant odor when in use, unplug it
from the main supply and contact the after-sales service.
Volume
EQ
TUNER
CD
TAPE
Tuning Mode
Up
S.Bass
AUX
Band
Power
Sound
Down
REC/Pause CD Sync.
Mute
Counter
Reset
Repeat
A B
Push Eject
Do not place heavy items on the
main lead. Main cable damage can
lead to damage of the equipment (fire
hazard) and can cause electric
shock.
18
Do not remove any equipment panels.
The inside of the unit
contains live components, which
cause electric shock.
19
Precautions When Using Compact
Discs
Before Contacting the After-Sales
Service
Technical Specifications
B
GB
Handle your compact discs with care. Always hold them by the
edges to avoid leaving fingerprints on the shiny surface.
When you have finished playing a compact disc, always put it back
in its case.
Do not fix paper or adhesive tape to the discs and do not write on
the label.
Clean them with a special-purpose cloth.
Store your compact discs in a clean place, out of direct sunlight,
where they will not be exposed to high temperatures.
Always use compact discs marked
.
It always takes a little time to become familiar with a new appliance.
If you have any of the problems listed below, try the solutions given.
They may save you the time and inconvenience of an unnecessary
service call.
RADIO
Problem
COMPACT
DIGITAL AUDIO
The system does not work
G
E
N
E
R
A
L
Precautions When Using Audio
Cassettes
Check that the tape in the cassette is sufficiently taught.
To prevent erasing a cassette that you wish to keep, remove the
safety tab on the upper edge of the cassette. To record a cassette,
where the tab has been broken, simply cover the opening with
adhesive tape.
When you have finished playing a cassette, always put it back in its
case.
Store your cassettes in a clean place, out of direct sunlight, where
they will not be exposed to high temperatures.
Avoid using 120-minute cassettes as they place unnecessary strain
on the tape mechanism.
SAMSUNG strives to improve its products at all times. Both the design specifications and these user
instructions are thus subject to change without notice.
C
D
Checks/Explanation
• The main lead is not correctly plugged into
a wall socket or the wall socket is not
switched on.
• The remote control batteries need replacing
or the polarity has not been respected.
• The On/Standby button has not been
pressed.
AM (MW)
Signal/noise ratio
40 dB
Usable sensitivity
56 dB
Total harmonic distortion
2%
FM
• The volume has been completely turned
down.
• The correct function (TUNER, CD, TAPE,
AUX) has not been selected.
• You have connected a set of earphones.
• The loudspeaker wires have been
disconnected.
• The Mute button has been pressed.
Signal/noise ratio
54 dB
Usable sensitivity
16 dB
Total harmonic distortion
0.5 %
The Timer does not work
• The timer has been stopped by pressing
Timer On/Off.
COMPACT DISC PLAYER
In case it does not work, even the
action is taken as above.
• Press the S.Bass button for 5
seconds in power ‘OFF’(standby), then it is
returned the original position (RESET)
There is no sound
The compact disc player does not
start playing
• The CD function has not been selected.
• The disc has been inserted face down or is
either dirty or scratched.
• The laser sensor is dirty or dusty.
• The system has not been installed on a flat,
horizontal surface.
• Condensation has formed in the player;
leave the system in a warm, airy room for at
least one hour.
Frequency range
80 dB (at 1 KHz) with filter
Distortion
0.1 % (at 1 KHz)
Channel separation
75 dB
Disc sizes
Diameter: 120 or 80 mm. Thickness: 1.2 mm
TAPE DECK
Frequency range
C
A
S
S
E
T
T
E
S
R
A
D
I
O
The tape does not start playing
• The TAPE function has not been selected.
• The cassette has not been inserted correctly.
• The cassette player has not been closed.
• The tape is either slack or broken.
The volume falls off
The cassette is not erased correctly
There is excessive wow and flutter
• The audio heads are dirty.
• The rollers or drive capstans are dirty.
• The tape is worn.
Reception is poor or no radio
stations are received at all
• The TUNER function has not been selected.
• The radio frequency has not been correctly
selected.
• The aerial has been disconnected or is not
facing the right way. Turn it until you find
the best orientation.
• You are in a building that blocks radio
waves; you must use an outside aerial.
20 Hz - 20 KHz
Signal/noise ratio
125 Hz ~ 8 KHz
Signal/noise ratio
40 dB
Channel separation
30 dB
Erasing effect
50 dB
AMPLIFIER
Output power
2 X 7.5 Watts RMS (total harmonic distortion : 10%)
Channel separation
40 dB
Signal/noise ratio
70 dB
GENERAL
If the above guidelines do not allow you to solve the problem, take a
note of:
The model and serial numbers, normally printed on the rear of
the system
Your warranty details
A clear description of the problem
Then contact your local dealer or SAMSUNG after-sales service.
20
Dimensions
150(W) x 235 (H) x 270(D) mm
21
THIS APPLIANCE IS MANUFACTURED BY:
ELECTRONICS
AH68-01205B
Download PDF