Samsung | NZ64K5747BK | Samsung NZ64K5747BK/EG, Autarkes Induktionskochfeld, 60 cm Benutzerhandbuch

Induction Hob
User manual
NZ64K5747BK
NZ64K5747BK_EU_DG68-00797A-00_EN.indd 1
3/2/2016 3:38:25 PM
Contents
Contents
Using this manual
3
Safety instructions
3
Disposing of the packaging material
Proper disposal of your old appliance
Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
6
6
7
Installing the hob
7
Safety instructions for the installer
Connecting to the mains power supply
Installing into the countertop
7
8
9
Parts and features
11
Cooking zones
11
Control panel
12
Components12
Induction heating
12
The key features of your appliance
13
Safety shutoff
14
Residual heat indicator
14
Temperature detection
14
Hob use
Initial cleaning
Cookware for induction cooking zones
Suitability test
Size of pans
Operating noises
Using suitable cookware
Using the touch control sensors
Switching the appliance on
Select cooking zone and heat setting
Switching the appliance off
15
15
15
15
16
16
16
17
17
17
18
Quick stop
18
Using the child safety lock
18
Timer (Count down)
19
Timer (Count up)
20
Using keep warm
20
Power boost control
20
Power management
21
Pause21
Flex control
21
Sound on/off
22
Suggested settings for cooking specific foods
22
Cleaning and care
23
Hob23
Light soiling
23
Stubborn soiling
23
Problem dirt
24
Hob frame (option)
24
To avoid damaging your appliance
24
Warranty and service
25
FAQs and troubleshooting
25
Service26
Technical data
Technical data
Cooking zones
Product information
27
27
27
27
2 English
NZ64K5747BK_EU_DG68-00797A-00_EN.indd 2
3/2/2016 3:38:25 PM
Safety instructions
Please take the time to read this owner’s manual, paying particular attention to the
safety information contained in the following section, before using your appliance.
Keep this manual for future reference.
If transferring ownership of the appliance, please remember to pass the manual on
to the new owner.
The safety aspects of this appliance comply with all accepted technical and safety
standards. However, as manufacturers we also believe it is our responsibility to
familiarize you with the following safety instructions.
The following symbols are used in this User Manual:
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have
been given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
WARNING
Hazards or unsafe practices that may result in severe personal injury or death.
CAUTION
Hazards or unsafe practices that may result in minor personal injury or property
damage.
CAUTION
To reduce the risk of fire, explosion, electric shock, or personal injury when using
your hob, follow these basic safety precaution.
NOTE
Useful tips, recommendations, or information that helps users manipulate the
product.
WARNING
Children should be supervised to ensure that they do not play
with the appliance.
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons in
order to avoid a hazard.
Appliance should allow the disconnection of the appliance
from the supply after installation. The disconnection may be
achieved by having the plug accessible or by incorporating a
switch in the fixed wiring in accordance with the wiring rules.
WARNING: If the surface is cracked, switch off the appliance to
avoid the possibility of electric shock.
During use the appliance becomes hot. Care should be taken to
avoid touching heating elements inside the hob.
English 3
NZ64K5747BK_EU_DG68-00797A-00_EN.indd 3
3/2/2016 3:38:27 PM
Using this manual
Using this manual
Safety instructions
WARNING: Accessible parts may become hot during use. Young
children should be kept away.
A steam cleaner is not to be used to clean the product.
Safety instructions
Metallic objects such as knives, forks, spoons and lids should
not be placed on the hob surface since they can get hot.
After use, switch off the hob element by its control and do not
rely on the pan detector.
Do not use harsh abrasive cleaners or sharp metal scrapers to
clean the hob glass since they can scratch the surface, which
may result in shattering of the glass.
Appliance is not intended to be operated by means of an
external timer or separate remote-control system.
WARNING: The appliance and its accessible parts become hot
during use. Care should be taken to avoid touching heating
elements inside the hob. Children less than 8 years of age shall
be kept away unless continuously supervised.
This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and user
maintenance shall not be made by children without supervision.
WARNING: Unattended cooking on a hob with fat or oil can be
dangerous and may result in fire.
NEVER try to extinguish a fire with water, but switch off the
appliance and then cover flame e.g. with a lid or a fire blanket.
WARNING: Danger of fire: do not store items on the cooking
surfaces.
WARNING: Use only hob guards designed by the manufacturer
of the cooking appliance. The use of inappropriate guards can
cause accidents.
The temperature of accessible surfaces may be high when the
appliance is operating.
Keep the appliance and its cord out of reach of children less
than 8 years.
4 English
NZ64K5747BK_EU_DG68-00797A-00_EN.indd 4
3/2/2016 3:38:27 PM
CAUTION
Be sure the appliance is properly installed and grounded by a
qualified technician.
Flush - mounted appliances may be operated only after they
have been installed in cabinets and workplaces that conform
to the relevant standards. This ensures sufficient protection
against contact for electrical units as required by the essential
safety standards.
If your appliance malfunctions or if fractures, cracks or splits
appear:
• switch off all cooking zones;
• disconnect the hob from the mains supply; and
• contact your local service centre.
If the cooktop cracks, turn the appliance off to avoid the
possibility of electric shock. Do not use your hob until the glass
surface has been replaced.
Liquid between the bottom of the pan and the hob can produce
steam pressure. Which may cause the pan to jump.
Always ensure that the hotplate and the base of the pan are
kept dry.
The cooking zones will become hot when you cook.
Always keep small children away from the appliance.
Keep all packaging materials well out of the reach of children,
as packaging materials can be dangerous to children.
This appliance is to be used only for normal cooking and frying
in the home. It is not designed for commercial or industrial use.
Never use the hob for heating the room.
Take care when plugging electrical appliances into mains
sockets near the hob. Mains leads must not come into contact
with the cooktop.
Overheated fat and oil can catch fire quickly. Never leave
surface units unattended when preparing foods in fat or oil, for
example, when cooking chips.
Turn the cooking zones off after use.
English 5
NZ64K5747BK_EU_DG68-00797A-00_EN.indd 5
3/2/2016 3:38:27 PM
Safety instructions
The appliance should be serviced only by qualified service
personnel. Repairs carried out by unqualified individuals may
cause injury or serious malfunction. If your appliance is in need
of repair, contact your local service centre. Failure to follow
these instructions may result in damage and void the warranty.
Do not use the hob to heat aluminium foil, products wrapped
in aluminium foil or frozen foods packaged in aluminium
cookware.
Safety instructions
Always keep the control panels clean and dry.
Never place combustible items on the hob, it may cause fire.
There is the risk of burns from the appliance if used carelessly.
Safety instructions
Cables from electrical appliances must not touch the hot surface
of the hob or hot cookware.
Do not use the hob to dry clothes.
Users with Pacemakers and Active Heart Implants must
keep their upper body at a minimum distance of 30 cm from
induction cooking zones when turned on. If in doubt, you
should consult the manufacturer of your device or your doctor.
(Induction hob model only)
Disposing of the packaging material
WARNING
All materials used to package the appliance are fully recyclable. Sheet and hard
foam parts are appropriately marked. Please dispose of packaging materials and
old appliances with due regard to safety and the environment.
Proper disposal of your old appliance
WARNING
Before disposing of your old appliance, make it inoperable so that it cannot be a
source of danger. To do this, have a qualified technician disconnect the appliance
from the mains supply and remove the mains lead.
The appliance may not be disposed of in the household rubbish.
Information about collection dates and public refuse disposal sites is available
from your local refuse department or council.
Do not attempt to repair, disassemble, or modify the appliance
yourself.
Always turn the appliance off before cleaning.
Clean the hob in accordance with the cleaning and care
instructions contained in this manual.
6 English
NZ64K5747BK_EU_DG68-00797A-00_EN.indd 6
3/2/2016 3:38:27 PM
Installing the hob
Correct Disposal of This Product (Waste Electrical & Electronic
Equipment)
(Applicable in countries with separate collection systems)
Be sure the new appliance is installed and grounded only by qualified personnel.
Please observe this instruction. The warranty will not cover any damage that may
occur as a result of improper installation.
Technical data is provided at the end of this manual.
Safety instructions for the installer
•
•
•
•
•
•
•
•
•
•
•
A device must be provided in the electrical installation that allows the
appliance to be disconnected from the mains at all poles with a contact
opening width of at least 3 mm. Suitable isolation devices include line
protecting cut - outs, fuses (screw type fuses are to be removed from the
holder), earth leakage trips and contactors.
With respect to fire protection, this appliance corresponds to EN 60335 - 2 6. This type of appliance may be installed with a high cupboard or wall on one
side.
The installation must guarantee shock protection.
The kitchen unit in which the appliance is fitted must satisfy the stability
requirements of DIN 68930.
For protection against moisture, all cut surfaces are to be sealed with a
suitable sealant.
On tiled work surfaces, the joints in the area where the hob sits must be
completely filled with grout.
On natural, artificial stone, or ceramic tops, the snap action springs must be
bonded in place with a suitable artificial resin or mixed adhesive.
Ensure that the seal is correctly seated against the work surface without any
gaps. Additional silicon sealant must not be applied; this would make removal
more difficult when servicing.
The hob must be pressed out from below when removed.
A board can be installed underneath the hob.
The ventilation gap between the worktop and front of the unit underneath it
must not be covered.
English 7
NZ64K5747BK_EU_DG68-00797A-00_EN.indd 7
3/2/2016 3:38:27 PM
Installing the hob
This marking on the product, accessories or literature
indicates that the product and its electronic accessories
(e.g. charger, headset, USB cable) should not be disposed
of with other household waste at the end of their working
life. To prevent possible harm to the environment or human
health from uncontrolled waste disposal, please separate
these items from other types of waste and recycle them
responsibly to promote the sustainable reuse of material
resources.
Household users should contact either the retailer where
they purchased this product, or their local government
office, for details of where and how they can take these
items for environmentally safe recycling.
Business users should contact their supplier and check the
terms and conditions of the purchase contract. This product
and its electronic accessories should not be mixed with
other commercial wastes for disposal.
WARNING
Installing the hob
Connecting to the mains power supply
Before connecting, check that the nominal voltage of the appliance, that is, the
voltage stated on the rating plate, corresponds to the available supply voltage. The
rating plate is located on the lower casing of the hob.
1N~ (32A)
01
02
04
03
05
06
WARNING
L
Shut off power to circuit before connecting wires to circuit.
Installing the hob
The heating element voltage is AC 230 V~. The appliance also works perfectly on
networks with AC 220 V~ or AC 240 V~. The hob is to be connected to the mains
using a device that allows the appliance to be disconnected from the mains at all
poles with a contact opening width of at least 3 mm, eg. automatic line protecting
cut - out, earth leakage trips or fuse.
WARNING
WARNING
Pay attention (conformity) to phase and neutral allocation of house connection and
appliance (connection schemes); otherwise, components can be damaged.
Warranty does not cover damage resulting from improper installation.
02
03
05
04
06
L1
L2
WARNING
If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified persons in order to avoid a hazard.
01
07
N
Blue
05
Gray
03
Black
06
Green/Yellow
05
03
06
N1
07
L2
N2
01
220-240 V ~
05
Blue
02
380-415 V ~
06
Gray
03
Brown
07
Green/Yellow
04
Black
2 x 1N~ (16A): Separate the wires before
connection.
04
02
L1
04
Brown
2N~ (16A): Separate the 2-phase wires
(L1 and L2) before connection.
WARNING
Once the hob is connected to the mains supply, check that all cooking zones are
ready for use by briefly switching each on in turn at the maximum setting with
suitable cookware.
220-240 V ~
02
N
01
The cable connections must be made in accordance with regulations and the
terminal screws tightened securely.
01
01
220-240 V ~
05
Black
02
Brown
06
Gray
03
Blue
07
Green/Yellow
04
220-240 V ~
WARNING
For correct supply connection, follow the wiring diagram attached near the
terminals.
8 English
NZ64K5747BK_EU_DG68-00797A-00_EN.indd 8
3/2/2016 3:38:30 PM
Installing into the countertop
01
02
NOTE
A
03
Make a note of the serial number on the
appliance rating label prior to installation.
This number will be required in the case
of requests for service and is no longer
accessible after installation, as it is on the
original rating plate on the underside of the
appliance.
06
04
08
07
09
05
10
11
12
NOTE
Pay special attention to the minimum space and clearance requirements.
NOTE
The bottom of the hob is equipped with a fan. If there is a drawer under the hob
it should not be used to store small objects or paper, since they could damage the
fan or interfere with the cooling if they are sucked into it.
No.
Explanation
Size
01
Height of
ventilation hole
Min 2 mm
02
Width of
ventilation hole
560 mm
01
02
No.
Explanation
01
Check 4 Point
Installing the hob
A. Serial number
Size
02
Drill diameter
Ø6
03
Right angle of cutting point
90 °
04
Cutting Width Size
560±1 mm
05
Cutting Depth Size
490±1 mm
06
Curve Size
R3
07
Size of table thickness
Max 50 mm,
Min 20 mm
08
Distance between end of table and cutting point
(Rear-side)
Min 60 mm
09
Depth of table
Min 600 mm
10
Distance between end of table and cutting point
(Left-side)
Min 60 mm
11
Distance between end of table and cutting point
(Right-side)
Min 60 mm
12
Distance between end of table and cutting point
(Front-side)
Min 50 mm
English 9
NZ64K5747BK_EU_DG68-00797A-00_EN.indd 9
3/2/2016 3:38:30 PM
Installing the hob
01
01
03
02
02
03
04
04
05
06
07
05
08
Installing the hob
No.
Explanation
Size
01
Distance between wall and Induction
Min 40 mm
02
Size of depth of Induction
520 mm
03
Distance between Induction and end of table
Min 40 mm
04
Distance between glass and case burner
25 mm
05
Distance between glass and case burner
15 mm
06
Distance between wall and case burner.
Min 60 mm
07
Size of depth of case burner
480 mm
08
Distance between case burner and end of table
Min 50 mm
No.
Explanation
Size
01
Width of rear
ventilation
Min 550 mm
02
Height of rear
ventilation
Min 35 mm
03
Depth of power
cord path
Max 65 mm
04
Width of power
cord path
Max 100 mm
05
Height of block
board
Min 5 mm
02
03
01
No.
Explanation
Min 20 mm
01
02
03
Size
Size of ventilation
Min 2 mm
Min 20 mm
10 English
NZ64K5747BK_EU_DG68-00797A-00_EN.indd 10
3/2/2016 3:38:30 PM
Parts and features
Cooking zones
02
01
03
Parts and features
04
01
Induction Flex zone 3300 W with Power Boost 3600 W
02
Induction cooking zone 1400 W with Power Boost 2000 W
03
Induction cooking zone 2200 W with Power Boost 3200 W
04
Control Panel
English 11
NZ64K5747BK_EU_DG68-00797A-00_EN.indd 11
3/2/2016 3:38:30 PM
Parts and features
Control panel
Components
04
03
05
06
07 08
03
Induction hob
Bracket Spring
Induction heating
03
01
03
02
•
09
10
Parts and features
B
01
On/Off control sensor
02
Flex zone sensor
03
Indicators for heat settings and residual heat
04
Cooking zone sensor
05
Keep warm sensor
06
Timer control sensor and indicator (Count down)
07
Timer control sensor (Count up)
08
Lock control sensor
09
Heat setting sensor
10
Pause&Go sensor
A
C
A. Induction coil
B. Induced currents
C. Electronic circuits
•
The Principle of Induction Heating:
When you place your cookware on a
cooking zone and you turn it on, the
electronic circuits in your induction
hob produce “induced currents” in the
bottom of the cookware which instantly
raise cookware’s temperature.
Greater speed in cooking and frying:
As the pan is heated directly and not
the glass, the efficiency is greater than
in other systems because no heat is
lost. Most of the energy absorbed is
transformed into heat.
12 English
NZ64K5747BK_EU_DG68-00797A-00_EN.indd 12
3/2/2016 3:38:30 PM
The key features of your appliance
•
•
•
•
•
•
•
•
•
•
•
•
Flex zone sensor : Use this function to expand cooking zone into complete
left side.
Flex zone: The Flex zone is a large, rectangle-shaped area designed for
cooking multiple dishes.
Quick Stop: This option reduces the step and time it takes to stop cooking by
simple one touch.
Parts and features
•
Ceramic glass cooking surface: The hob has ceramic, rapid-response cooking
zones.
Touch control sensors: Your appliance is operated using touch control sensors.
Easy cleaning: The flat, ceramic glass cooktop provides easy cleaning.
On/Off sensor: The “On/Off” control sensor provides the appliance with a
separate mains switch. Touching this sensor switches the power supply on or
off completely.
Control and function indicators: Digital displays and indicator lights provide
information about settings and activated functions, as well as the presence of
residual heat in the various cooking zones.
Safety shutoff: A safety shutoff ensures that cooking zones switch off
automatically after a period of time if the setting has not been changed.
Power Boost : Use this function to heat up the contents of the pan faster
than maximum power level
. (The display will show
.)
Auto Pan-Detection: Each cooking zone incorporates an automatic pandetection system, the system is calibrated in order to recognize pans of a
diameter just slightly smaller than the cooking zone. Pans must always be
placed centrally on each cooking zone. And you should use suitable cookware.
Digital displays:
to
,
selected heat settings
•
residual heat (Stay Hot)
•
residual heat
•
the child lock is activated
•
message, the touch sensor button has been touched for longer than
•
8 seconds.
message, when the hob is overheated because of abnormal operation.
•
(example : operation with empty cookware)
, cookware is unsuitable or too small or no cookware has been placed
•
on the cooking zone.
Keep warm
: Use this function to keep cooked food warm. The display will
show
.
Pause
: Use this fuction to switch all cooking zones on to the low power
setting. (example : to take a telephone call) The display will show
.
•
English 13
NZ64K5747BK_EU_DG68-00797A-00_EN.indd 13
3/2/2016 3:38:31 PM
Parts and features
Safety shutoff
Residual heat indicator
If one of the cooking zones is not switched off or the heat setting is not adjusted
after an extended period of time, that particular cooking zone will automatically
switch itself off.
Any residual warmth will be indicated with
,
(for “hot”) in the digital
displays corresponding to the particular cooking zones.
The cooking zones switch themselves off at the following times.
When an individual cooking zone or the hob is turned off, the presence of residual
heat is shown with an
,
(for “hot”) in the digital display of the appropriate
cooking zones. Even after the cooking zone has been switched off, the residual
heat indicator goes out only after the cooking zone has cooled.
You can use the residual heat for thawing or keeping food warm.
Parts and features
Heat setting
Switch off
1-3
After 6 hours
4-6
After 5 hours
7-9
After 4 hours
10-15
After 1.5 hours
NOTE
If the Hob is overheated because of abnormal operation,
And the Hob will be switched off.
WARNING
As long as the residual heat indicator is illuminated, there is a risk of burns.
WARNING
If the power supply is interrupted, the
,
symbol will go out and information
about residual heat will no longer be available.
However, it may still be possible to burn yourself. This can be avoided by always
taking care when near the hob.
Temperature detection
will be displayed.
NOTE
If cookware is unsuitable or too small or no cookware has been placed on the
cooking zone,
will be displayed.
And after 1 minute the corresponding cooking zone will be switched off.
If for any reason the temperatures on any of the cooking zones were to exceed the
safety levels, should this happen then the cooking zone will automatically reduce
to a lower power level.
When you have finished using the hob, the cooling fan will continue to run until
the hob’s electronics has cooled down. And the cooling fan switched itself off
depending upon the temperature of the electronics.
NOTE
Should one or more of the cooking zones switch off before the indicated time has
elapsed, see the section “Troubleshooting”.
Other reasons why a cooking zone will switch itself off
All cooking zones will switch themselves off if liquid boils over and lands on the
control panel.
The automatic shutoff will also be activated if you place a damp cloth on the
control panel. In both of these instances, the appliance will need to be switched
on again using the main On/Off control
sensor after the liquid or the cloth has
been removed.
14 English
NZ64K5747BK_EU_DG68-00797A-00_EN.indd 14
3/2/2016 3:38:31 PM
Hob use
Suitability test
Initial cleaning
Wipe the ceramic glass surface with a damp cloth and ceramic cooktop glass
cleaner.
Cookware is suitable for induction cooking,
if a magnet sticks to the bottom of the
cookware and cookware is labelled as
suitable by the cookware manufacturer.
WARNING
Do not use caustic or abrasive cleaners. The surface could be damaged.
Cookware for induction cooking zones
The induction hob can only be turned on when cookware with a magnetic base is
placed on one of the cooking zones. You can use the following suitable cookware.
NOTE
Cookware material
Suitable
Steel, Enamelled steel
Yes
Cast iron
Yes
Stainless steel
If appropriately labelled by the manufacturer
Aluminium, Copper, Brass
No
Glass, Ceramic, Porcelain
No
Hob use
Cookware material
Induction cooking may not function properly on nonferrous cookware whose edge
doesn’t stick to the magnet, or on nonferrous cookware whose bottom is ironcoated.
NOTE
Cookware for induction hob is labelled as suitable by the manufacturer.
NOTE
When used on induction cooking zones, cookware may make noises. These noises
are normal.
NOTE
Non-stainless steel cookware are less heat-conductive than stainless steel. Using
non-stainless steel cookware lengthens cooking time.
English 15
NZ64K5747BK_EU_DG68-00797A-00_EN.indd 15
3/2/2016 3:38:32 PM
Hob use
Size of pans
Using suitable cookware
Induction cooking zones adapt automatically to the size of the bottom of the
cookware up to a certain limit. However the magnetic part of the bottom of the
cookware must have a minimum diameter depending upon the size of the cooking
zone.
Better pans produce better results.
• You can recognise good pans by their bases. The base should be as thick and
flat as possible.
• When buying new pans, pay particular attention to the diameter of the base.
Manufacturers often give only the diameter of the upper rim.
• Do not use pans which have damaged bases with rough edges or burrs.
Permanent scratching can occur if these pans are slid across the surface.
• When cold, pan bases are normally bowed slightly inwards (concave). They
should never be bowed outwards (convex).
• If you wish to use a special type of pan, for example, a pressure cooker, a
simmering pan, or a wok, please observe the manufacturer’s instructions.
Cooking zones
Minimum diameter of the bottom of the cookware
Right Rear Burner
(145 mm)
100 mm
Right Front Burner
(210 mm)
140 mm
Front or Rear Flex zone
120 mm
Flex zone
240 mm (long side dimension), oval, fish kettle
Operating noises
Hob use
If you can hear.
• Cracking noise: cookware is made of different materials.
• Whistling: you use more than two cooking zones and the cookware. is made of
different materials.
• Humming: you use high power levels.
• Clicking: electric switching occurs.
• Hissing, Buzzing: the fan operates.
The noise are normal and do not refer to any defects.
WARNING
Do not use cookware of different size and material.
Using cookware of different sizes or materials may cause noises and vibrations.
Energy saving tips
NOTE
You can save valuable energy by observing
the following points.
• Always position pots and pans before
switching on the cooking zone.
• Dirty cooking zones and pan bases
increase power consumption.
• When possible, position the lids
firmly on the pots and pans to cover
completely.
• Switch the cooking zones off before
the end of the cooking time to use the
residual heat for keeping foods warm
or for thawing.
NOTE
Using low power levels (1~5) may causing clicking noises.
16 English
NZ64K5747BK_EU_DG68-00797A-00_EN.indd 16
3/2/2016 3:38:32 PM
Select cooking zone and heat setting
NOTE
Do not use one piece of cookware on both the left
and right cooking zones.
1. For selecting the cooking zone, touch
the corresponding cooking zone’s
sensor.
2. For setting and adjusting the power
level, touch the Heat setting sensor.
Using the touch control sensors
To operate the touch control sensors, touch the desired panel with the tip of your
pointed finger until the relevant displays illuminate or go out, or until the desired
function is activated.
Ensure that you are touching only one sensor panel when operating the appliance.
If your finger is too flat on the panel, an adjacent sensor may be actuated as well.
NOTE
Switching the appliance on
The default level is set to 15 when selecting the cooking zone.
NOTE
If more than one sensor is pressed for longer than 8 seconds,
heat setting display.
will show in the
NOTE
After the On/Off control
sensor has been actuated to switch on your appliance,
a heat setting must be selected within approximately 20 seconds. Otherwise, the
appliance will switch itself off for safety reasons.
English 17
NZ64K5747BK_EU_DG68-00797A-00_EN.indd 17
3/2/2016 3:38:32 PM
Hob use
The appliance is switched on using the On/
Off control
sensor.
Touch the On/Off control
sensor for
approximately 1~2 seconds.
The digital displays will show
.
Hob use
Switching the appliance off
Using the child safety lock
To completely switch off the appliance, use
the On/Off control
sensor.
Touch the On/Off control
sensor for
approximately 1~2 seconds.
You can use the child safety lock to safeguard against unintentionally turning on a
cooking zone and activating the cooking surface. Also the control panel, with the
exception of the On/Off control
sensor (Only turn off control), can be locked in
order to prevent the settings from being changed unintentionally, for example, by
wiping over the panel with a cloth.
Switching the child safety lock On/Off
NOTE
1. Touch the Lock control
sensor for
approximately 3 seconds.
An acoustic signal will sound as
confirmation.
After switching off a single cooking zone or the entire cooking surface, the
presence of residual heat will be indicated in the digital displays of the
corresponding cooking zones in the form of an
,
two steps for “hot”.
The temperature is lowered,
,
wil be disappeared.
Quick stop
2. Touch any control sensor.
will appear in the displays,
indicating the child safety lock has
been activated.
3. For switching the child safety lock off,
touch the Lock control
sensor again
for 3 seconds. An acoustic signal will
sound as confirmation.
To switch off a cooking zone, press the
cooking zone sensor during 2 seconds.
Hob use
NOTE
The Quick Stop function does not work with the Flex Zone sensor
.
NOTE
Regardless of power on/off, child lock is activated.
NOTE
You can use Lock control during cooking. In this case, To turn off the burner, you
should operate lock off or Power OFF.
18 English
NZ64K5747BK_EU_DG68-00797A-00_EN.indd 18
3/2/2016 3:38:33 PM
Timer (Count down)
4. To cancel the timer settings, select the
target burner and hold down the Timer
control
sensor for 2 seconds. This
will cancel the burner’s timer settings
with a beep. If holding down the Timer
control
sensor for 2 seconds without
selecting a burner, this will cancel
the timer settings of the last changed
burner.
Using the timer as a safety shutoff:
If a specific time is set for a cooking zone, the cooking zone will shut itself off once
this period of time has elapsed. This function can be used for multiple cooking
zones simultaneously.
Setting the safety shutoff
The cooking zone(s) for which you want to apply the safety shutoff must be
switched on.
1. After switched on, press the
corresponding cooking zone to activate
the flash signal for the corresponding
cooking zone display.
To display the time remaining for any of the cooking zones, use the Timer control
sensor after select burner.
The corresponding control indicator will begin to blink slowly.
The settings are reset using the Timer setting sensor ( or ). After the set period
of time has elapsed, the cooking zone automatically switches itself off, an acoustic
signal sounds as confirmation and the timer display indicates.
NOTE
To change the settings quicker, touch and hold any of the
until the desired value is reached.
or
control sensors
Hob use
2. Press Timer control
sensor. The
number 10 will be displayed above the
timer display.
NOTE
The default setting of the timer is 10.
3. Use the Timer setting sensor
( or ) to set the desired amount
of time, for example, 15 minutes,
after which the cooking zone will
automatically switch itself off. The
safety shutoff is now activated.
NOTE
The timer can be set from 1 to 99.
English 19
NZ64K5747BK_EU_DG68-00797A-00_EN.indd 19
3/2/2016 3:38:33 PM
Hob use
Timer (Count up)
3. The burner display will be changed
Touch again to turn off the burner.
For the count up timer to be used, the appliance must be switched on but all the
cooking zones must be not use timer as a safety shutoff.
1. Touch the Timer control
sensor.
will appear in the timer display.
Power boost control
2. The count up timer function becomes
active and the display numbers
increase over time. To cancel the timer
settings, hold down the Timer control
The Power Boost
function makes additional power available to the each cooking
zones. (example : bring a large volume of water to the boil)
sensor for 2 seconds.
3. To stop the timer, touch the Timer
control
sensor.
Using keep warm
Cooking zones
Max Boost time
145 mm
10 min
210 mm
10 min
Front or Rear Flex Plus
10 min
Complete Flex Plus
5 min
After these times, the cooking zones automatically return to power level
Hob use
1. Use this function to Keep cooked
food Warm. Touch the corresponding
cooking zone’s sensor.
2. Touch the Keep warm
.
NOTE
In certain circumstances, the Power boost function may be deactivated
automatically to protect the internal electronic components of the hob.
For example, It is impossible to output max power on Flex zone rear and Flex zone
front at the same time.
sensor.
20 English
NZ64K5747BK_EU_DG68-00797A-00_EN.indd 20
3/2/2016 3:38:34 PM
Power management
Flex control
The cooking zones have a maximum power available to them.
If this power range is exceeded by switching on the Power Boost
function,
Power Management automatically reduced the heat setting of cooking zone.
The Flex function can operate complete left side cooking zone for using large size
cookware. (example : oval cookware, fish kettle)
1
3
2
4
1. Touch the Flex zone
• No.1 and No.2 is paired
• No.3 and No.4 is paired
The indicator for this cooking zone
alternates for some seconds between the set
heat setting and the maximum possible heat
setting. After then, the indicator changes
from the set heat setting to maximum
possible heat setting.
sensor.
2. For setting and adjusting the power
level, touch the Heat setting sensor.
Pause
Control Panel
To Switch On
Touch Pause
To Switch Off
Touch Pause
NOTE
Hob use
The Pause
function simultaneously switches all cooking zones that are
switched on to the low power setting and then back to the heat setting that was
previously set. This function can be used to briefly interrupt and then continue the
cooking process e.g. to take a telephone call.
When the Pause
function is activated, all touch sensors except for the Pause
, Lock
and the On/Off control
sensors are disabled. To resume cooking,
touch the Pause
sensor again.
Touch the Flex zone sensor during opertaing, Flex zone function will be off.
NOTE
If you touch Flex zone sensor while each burner operation different level, burner
set at a high level.
Display
Return to previous power level
English 21
NZ64K5747BK_EU_DG68-00797A-00_EN.indd 21
3/2/2016 3:38:34 PM
Hob use
Sound on/off
Suggested settings for cooking specific foods
1. Touch the On/Off control
sensor for
approximately 1~2 seconds.
2. Touch the Pause
sensor for
3 seconds within 10 seconds after
Power On.
3. Sound will OFF and
display.
The figures in the table below are guidelines. The heat settings required for
various cooking methods depend on a number of variables, including the quality
of the cookware being used and the type and amount of food being cooked.
Switch setting
Cooking method
14-15
Warming
Sautéing
Frying
Warming large amounts of liquid, boiling
noodles, searing meat, browning goulash,
braising meat
8-11
Intensive
Frying
Steak, sirloin, hash browns, sausages,
pancakes / griddle cakes
7-10
Frying
Schnitzel / chops, liver, fish, rissoles, fried
eggs
5-7
Boiling
Cooking up to 1.5 l liquid, potatoes,
vegetables
2-4
Steaming
Stewing
Boiling
Steaming and stewing of small amounts of
vegetables, boiling rice and milk dishes
1-2
Melting
Melting butter, dissolving gelatine, melting
chocolate
will show in the
Hob use
4. To change Sound setting, repeat No1
and No2 procedure.
Sound will ON and
will show in the
display.
Examples for Use
NOTE
The heat settings indicated in the table above are provided only as guidelines for
your reference.
NOTE
You will need to adjust the heat settings according to specific cookware and foods.
NOTE
Turn on the Power, It is not possible to operate sound on/off control after
10 seconds.
22 English
NZ64K5747BK_EU_DG68-00797A-00_EN.indd 22
3/2/2016 3:38:35 PM
Cleaning and care
Hob
WARNING
Cleaning agents must not come into contact with a heated ceramic glass surface:
All cleaning agents must be removed with adequate amounts of clean water after
cleaning because they can have a caustic effect when the surface becomes hot.
Do not use any aggressive cleaners such as grill or oven sprays, scouring pads or
abrasive pan cleaners.
NOTE
Clean the ceramic glass surface after each use when it is still warm to the
touch. This will prevent spillage from becoming burnt onto the surface. Remove
scales, watermarks, fat drippings and metallic discolouration with the use of a
commercially available ceramic glass or stainless steel cleaner.
Stubborn soiling
1. To remove food that has boiled over
and stubborn splashes, use a glass
scraper.
2. Place the glass scraper at an angle to
the ceramic glass surface.
3. Remove soiling by scraping with the
blade.
NOTE
Glass scrapers and ceramic glass cleaners
are available from specialty retailers.
Light soiling
Cleaning and care
1. Wipe the ceramic glass surface with a damp cloth.
2. Rub dry with a clean cloth. Remnants of cleaning agent must not be left on the
surface.
3. Thoroughly clean the entire ceramic glass cooking surface once a week with a
commercially available ceramic glass or stainless steel cleaner.
4. Wipe the ceramic glass surface using adequate amounts of clean water and
rub dry with a clean lint - free cloth.
English 23
NZ64K5747BK_EU_DG68-00797A-00_EN.indd 23
3/2/2016 3:38:35 PM
Cleaning and care
Problem dirt
Hob frame (option)
1. Remove burnt-on sugar, melted plastic,
aluminium foil or other materials with
a glass scraper immediately and while
still hot.
WARNING
There is a risk of burning yourself when the
glass scraper is used on a hot cooking zone:
2. Clean the hob as normal when it has
cooled down. If the cooking zone on
which something has melted has been
allowed to cool, warm it up again for
cleaning.
NOTE
Cleaning and care
Scratches or dark blemishes on the ceramic
glass surface, caused, for example, by a
pan with sharp edges, cannot be removed.
However, they do not impair the function of
the hob.
WARNING
Do not use vinegar, lemon juice or scale remover on the hob frame; otherwise dull
blemishes will appear.
1. Wipe the frame with a damp cloth.
2. Moisten dried debris with a wet cloth. Wipe and rub dry.
To avoid damaging your appliance
•
•
•
•
•
•
•
Do not use the hob as a work surface or for storage.
Do not operate a cooking zone if there is no pan on the hob or if the pan is
empty.
Ceramic glass is very tough and resistant to temperature shock, but it is
not unbreakable. It can be damaged by a particularly sharp or hard object
dropping onto the hob.
Do not place pans on the hob frame. Scratching and damage to the finish may
occur.
Avoid spilling acidic liquids, for example, vinegar, lemon juice and descaling
agents, onto the hob frame, since such liquids can cause dull spots.
If sugar or a preparation containing sugar comes into contact with a hot
cooking zone and melts, it should be cleaned off immediately with a kitchen
scraper while it is still hot. If allowed to cool, it may damage the surface when
removed.
Keep all items and materials that could melt, for example, plastics, aluminium
foil and oven foils, away from the ceramic glass surface. If something of this
nature melts onto the hob, it must be removed immediately with a scraper.
24 English
NZ64K5747BK_EU_DG68-00797A-00_EN.indd 24
3/2/2016 3:38:35 PM
Warranty and service
FAQs and troubleshooting
Information code
A fault may result from a minor information that you can correct yourself with
the help of the following instructions. Do not attempt any further repairs if the
following instructions do not help in each specific case.
WARNING
Repairs to the appliance are to be performed only by a qualified service technician.
Improperly effected repairs may result in considerable risk to the user. If your
appliance needs repair, please contact your customer service centre.
Problem
Possible cause
The fuse in the house
wiring is intact.
•
If the fuses trip a
number of times,
call an authorised
electrician.
What should I do if the
cooking zones will not
switch on?
•
The On/Off sensor
was accidentally
actuated.
The control panel is
partially covered by a
damp cloth or liquid.
•
The appliance is
properly switched on.
Clean the control
panel.
The On/Off sensor
was accidentally
actuated.
The control panel is
partially covered by a
damp cloth or liquid.
•
The cooking zone
was only briefly used
and therefore did not
become hot enough.
•
•
What should I do if
the display except for
,
the residual
warmth indicator
suddenly disppears?
•
What should I do if,
after the cooking
zones have been
switched off,
residual warmth is
not indicated in the
display
•
•
Check the Auto Cook sensor.
C1
The temperature is sensed
higher than specified.
•
•
The appliance is
properly switched on.
Clean the control
panel.
If the cooking zone is
hot, please call a local
service center.
Restart the appliance
using the Power button.
If the problem continues,
disconnect power for
more than 30 seconds.
Then, restart the appliance
and try again. If the
problem still continues,
contact a local service
center.
C2
Check the Auto Cook sensor.
A2
The DC Motor fails to operate
because of problems with the
PCB or wiring, or electrical
disturbance on the motor
blade.
d0
The sensor is pressed for
more than 8 seconds.
Check if the sensor pad
is wet or pressed. If the
problem continues, restart
the appliance using the
Power button. If the
problem still continues,
contact a local service
center.
F0
Communications between
main and sub PCBs fail.
F2
The touch-enabled IC
communicates abnormally.
Restart the appliance
using the Power button.
If the problem continues,
disconnect power for
more than 30 seconds.
Then, restart the
appliance. If the problem
still continues, contact a
local service center.
English 25
NZ64K5747BK_EU_DG68-00797A-00_EN.indd 25
3/2/2016 3:38:36 PM
Warranty and service
•
Solution
C0
Solution
What should I do if the
cooking zones are not
functioning?
Possible cause
Warranty and service
What should I do if the cooking zone will not switch on or off?
Service
This could be due to one of the following possibilities:
• The control panel is partially covered by a damp cloth or liquid.
• The child safety lock is on. and display “L”.
Before calling for assistance or service, please check the section “Troubleshooting”.
If you still need help, follow the instructions below.
What should I do if the
display is illuminated?
Check for the following:
• The control panel is partially covered by a damp cloth or liquid.
To reset, press the On/Off control sensor.
• If liquid has overflowed on control panel, please wipe the liquid.
What should I do if the
display is illuminated?
Check for the following:
• The hob is overheated because of abnormal operation.
• After hob is cooled down, press the On/Off control sensor for resetting.
What should I do if the
display is illuminated?
Check for the following:
• Cookware is unsuitable or too small or no cookware has been placed on the
cooking zone.
• If you use suitable cookware, displayed message will automatically disappear.
What should I do if the cooling fan runs after the hob is turned off?
Warranty and service
Check for the following:
• When you have finished using the hob, the cooling fan runs by itself for
cooling down.
• After the hob’s electronics has cooled down or elapsed max time (10 minutes)
the cooling fan will be turned off.
• If you request a service call because of an information made in operating the
appliance, the visit from the customer service technician may incur a charge
even during the warranty period.
Is it a technical fault?
If so, please contact your customer service centre.
Always prepare in advance for the discussion. This will ease the process of
diagnosing the problem and also make it easier to decide if a customer service
visit is necessary.
Please take note of the following information.
• What form does the problem take?
• Under what circumstances does the problem occur?
When calling, please know the model and serial number of your appliance. This
information is provided on the rating plate as follows:
•
•
Model description
S/N code (15 digits)
We recommend that you record the information here for easy reference.
•
•
Model:
Serial number:
When do you incur costs even during the warranty period?
•
•
If you could have remedied the problem yourself by applying one of the
solutions provided in the section “Troubleshooting”.
If the customer service technician has to make several service calls because he
was not provided with all of the relevant information before his visit and as a
result, for example, has to make additional trips for parts. Preparing for your
phone call as described above will save you the cost of these trips.
26 English
NZ64K5747BK_EU_DG68-00797A-00_EN.indd 26
3/2/2016 3:38:36 PM
Technical data
Product information
Technical data
Appliance dimensions
Worktop cut - out
dimensions
Width
600 mm
Supplier’s name
Samsung Electronics co. Ltd.
Depth
520 mm
Model identification
NZ64K5747BK
Height
56 mm
Type of hob
Built-In
Width
560 mm
Depth
490 mm
Heating technology
Induction cooking zones and cooking
area
Height
72 mm
Number of cooking zones and/or area
3
Corner radius
3 mm
For circular cooking zones or
area:diameter of useful surface area
per electric heated cooking zone (Ø)
21.0 cm, 14.5 cm
For non-circular cooking zones or
area: length and width of useful
surface area per electric heated
cooking zone or area (L x W)
20.0 x 38.0 cm
220 - 240 V ~ 50 / 60 Hz
Connection voltage
7.2 kW
Maximum connected load power
Weight
Net
12.7 kg
Gross
15.5 kg
Cooking zones
Diameter
Power
Right Front
210 mm
2200 W / Boost 3200 W
Right Rear
145 mm
1400 W / Boost 2000 W
Flex Front
-
1800 W / Boost 2600 W
Flex Rear
-
1800 W / Boost 2600 W
Complete Flex
-
3300 W / Boost 3600 W
Energy consumption for the hob
(EC electric hob)
Ø 21.0 cm : 182.5 Wh/kg
Ø 14.5 cm : 192.5 Wh/kg
20.0 x 38.0 cm : 196.7 Wh/kg
190.7 Wh/kg
* Data determined according to standard EN 60350-2 and Commission Regulations
(EU) No 66/2014.
Energy saving tips
•
•
•
Always position pots and pans before switching on the cooking zone.
Dirty cooking zones and pan bases increase power consumption.
Using a pressure cooker reduces cooking time.
English 27
NZ64K5747BK_EU_DG68-00797A-00_EN.indd 27
3/2/2016 3:38:36 PM
Technical data
Position
Energy consumption per cooking zone
or area (EC electric cooking)
Please be advised that the Samsung warranty does NOT cover service calls to explain product operation, correct improper installation, or perform normal cleaning or
maintenance.
QUESTIONS OR COMMENTS?
COUNTRY
CALL
OR VISIT US ONLINE AT
AUSTRIA
0800-SAMSUNG (0800-7267864)
[Only for Premium HA] 0800-366661
[Only for Dealers] 0810-112233"
www.samsung.com/at/support
BELGIUM
02-201-24-18
www.samsung.com/be/support (Dutch)
www.samsung.com/be_fr/support (French)
DENMARK
70 70 19 70
www.samsung.com/dk/support
FINLAND
030-6227 515
www.samsung.com/fi/support
FRANCE
01 48 63 00 00
www.samsung.com/fr/support
GERMANY
0180 6 SAMSUNG bzw.
0180 6 7267864*
(*0,20 €/Anruf aus dem dt. Festnetz, aus dem Mobilfunk max. 0,60 €/Anruf)
www.samsung.com/de/support
ITALIA
800-SAMSUNG (800.7267864)
www.samsung.com/it/support
CYPRUS
8009 4000 only from landline, toll free
GREECE
80111-SAMSUNG (80111 726 7864) only from land line
(+30) 210 6897691 from mobile and land line
www.samsung.com/gr/support
LUXEMBURG
261 03 710
www.samsung.com/be_fr/support
NETHERLANDS
0900-SAMSUNG (0900-7267864) (€ 0,10/Min)
www.samsung.com/nl/support
NORWAY
815 56480
www.samsung.com/no/support
PORTUGAL
808 20 7267
www.samsung.com/pt/support
SPAIN
0034902172678
www.samsung.com/es/support
SWEDEN
0771 726 7864 (0771-SAMSUNG)
www.samsung.com/se/support
SWITZERLAND
0800 726 78 64 (0800-SAMSUNG)
www.samsung.com/ch/support (German)
www.samsung.com/ch_fr/support (French)
UK
0330 SAMSUNG (7267864)
www.samsung.com/uk/support
EIRE
0818 717100
www.samsung.com/ie/support
DG68-00797A-00
NZ64K5747BK_EU_DG68-00797A-00_EN.indd 28
3/2/2016 3:38:36 PM
Download PDF