Samsung | DVD-SH893A | Samsung DVD-SH893A Benutzerhandbuch

DVD-SH893
DVD-SH895
DVD-SH897
DVD
user manual
imagine the possibilities
Thanks you for purchasing this Samsung product.
To receive more complete service, please register
your product at
www.samsung.com/register
getting started
Warning
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER (OR BACK).
NO USER-SERVICEABLE PARTS ARE INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
This symbol indicates “dangerous voltage”
inside the product that presents a risk of
electric shock or personal injury.
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QULAIFIED SERVICE PERSONNEL.
This symbol indicates important
instructions accompanying the product.
Do not install this equipment in a confined space such as a bookcase or similar unit.
WARNING : To prevent damage which may result in fire or electric shock hazard, do not expose this appliance to
rain or moisture.
CAUTION : HDD & DVD Recorder USES AN INVISIBLE LASER BEAM WHICH CAN CAUSE HAZARDOUS
RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE HDD & DVD Recorder CORRECTLY
AS INSTRUCTED.
CAUTION
THIS PRODUCT UTILIZES A LASER.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE
SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.
This product satisfies CE regulations when shielded cables and connectors are used to connect the unit to other
equipment. To prevent electromagnetic interference with electric appliances, such as radios and televisions, use
shielded cables and connectors for connections.
IMPORTANT NOTE
The mains lead on this equipment is supplied with a moulded plug incorporating a fuse. The value of the fuse is indicated
on the pin face of the plug. If it requires replacing, a fuse approved to BS1362 of the same rating must be used.
Never use the plug with the fuse cover omitted if the cover is detachable. If a replacement fuse cover is required, it
must be of the same colour as the pin face of the plug. Replacement covers are available from your dealer.
If the fitted plug is not suitable for the power points in your house or the cable is not long enough to reach a power
point, you should obtain a suitable safety approved extension lead or consult your dealer for assistance.
However, if there is no alternative to cutting off the plug, remove the fuse and then safely dispose of the plug. Do not
connect the plug to a mains jack, as there is a risk of shock hazard from the bared flexible cord.
To disconnect the apparatus from the mains, the plug must be pulled out from the mains socket, therefore the
mains plug shall be readily operable.
The product unit accompanying this user manual is licenced under certain intellectual property rights of certain third
parties. This licence is limited to private non-commercial use by end-user consumers for licenced contents.
No rights are granted for commercial use.
The licence does not cover any product unit other than this product unit and the licence does not extend to any
unlicenced product unit or process conforming to ISO/IEC 11172-3 or ISO/IEC 13818-3 used or sold in
combination with this product unit. The licence only covers the use of this product unit to encode and/or decode
audio files conforming to the ISO/IEC 11172-3 or ISO/IEC 13818-3. No rights are granted under this licence for
product features or functions that do not conform to the ISO/IEC 11172-3 or ISO/IEC 13818-3.
_ getting started
Precaution
Important Safety Instructions
Read these operating instructions carefully before using the unit. Follow all the safety instructions listed below.
Keep these operating instructions handy for future reference.
Read these instructions.
2)
Keep these instructions.
3)
Heed all warnings.
4)
Follow all instructions.
5)
Do not use this apparatus near water.
6)
Clean only with dry cloth.
7)
Do not block any ventilation openings, Install in accordance with the manufacturer’s instructions.
8)
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9)
Do not defeat the safety purpose of the polarized or grounding- type plug. A polarized plug has two
blades with one wider than the other. A grounding-type plug has two blades and a third grounding
prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit
into your outlet, consult an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,
the point where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury
from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate
normally, or has been dropped.
Handling Cautions
~ Before connecting other components to this HDD & DVD Recorder, be sure to turn them all off.
~ Do not move the HDD & DVD Recorder while a disc is being played, or the disc may be scratched or
broken, the HDD & DVD Recorder internal parts may be damaged.
~ Do not put a flower vase filled with water or any small metal objects on the HDD & DVD Recorder.
~ Be careful not to put your hand into the disc tray.
~ Do not place anything other than the disc in the disc tray.
~ Exterior interference such as lightning and static electricity can affect normal operation of this HDD & DVD
Recorder. If this occurs, turn the HDD & DVD Recorder off and on again with the STANDBY/ON button, or
disconnect and then reconnect the AC power cord to the AC power outlet. The HDD & DVD Recorder will
operate normally.
~ Be sure to remove the disc and turn off the HDD & DVD Recorder after use.
~ Disconnect the AC power cord from the AC outlet when you don’t intend to use the HDD & DVD Recorder
for long periods of time.
~ Clean the disc by wiping in a straight line from the inside to the outside of the disc.
~ Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases,
shall be placed on the apparatus.
~ The Mains plug is used as a disconnect device and shall stay readily operable at any time.
English _
● getting started
1)
getting started
Maintenance of Cabinet
For safety reasons, be sure to disconnect the AC power cord from the AC outlet.
~ Do not use benzene, thinner, or other solvents for cleaning.
~ Wipe the cabinet with a soft cloth.
HDD (Hard Disk Drive)
The hard disk has a high storage density, which enables long recording durations and quick access to written
data. However, it can easily be damaged by shock, vibration or dust and should be kept away from magnets.
To avoid losing important data, observe the following precautions.
~ Do not use the HDD & DVD Recorder in a place subject to extreme changes in temperature.
~ Do not apply a strong shock to the HDD & DVD Recorder.
~ Do not place the HDD & DVD Recorder in a location subject to mechanical vibrations or in an unstable
location.
~ Do not place the HDD & DVD Recorder on top of a heat source.
~ Do not disconnect the AC power cord while the power is on.
~ Do not attempt to change the hard disk. This may result in a malfunction.
Should the hard disk be damaged, you cannot recover lost data. The hard disk is only a temporary storage
space.
Disc Handling
~ Use discs with regular shapes. If an irregular disc (a disc with a special shape) is
used, this HDD & DVD Recorder may be damaged.
Holding discs
~ Avoid touching the surface of a disc where recording is performed.
DVD-RAM, DVD±RW and DVD±R
~ Clean with an optional DVD-RAM/PD disc cleaner (LF-K200DCA1 where available).
Do not use cleaners or cloths for CDs to clean DVD-RAM/±RW/±R discs.
DVD-Video, Audio-CD
~ Wipe off dirt or contamination on the disc with a soft cloth.
Cautions on handling discs
~ Do not write on the printed side with a ball-point pen or pencil.
~ Do not use record cleaning sprays or antistatic. Also, do not use volatile chemicals, such as benzene or
thinner.
~ Do not apply labels or stickers to discs. (Do not use discs fixed with exposed tape adhesive or leftover
peeled-off stickers.)
~ Do not use scratch-proof protectors or covers.
~ Do not use discs printed with label printers available on the market.
~ Do not load warped or cracked discs.
Disc Storage
Be careful not to harm the disc because the data on these discs is highly vulnerable to the environment.
~ Do not keep under direct sunlight.
~ Keep in a cool ventilated area.
~ Store vertically.
_ getting started
~ Keep in a clean protection jacket.
~ If you move your HDD & DVD Recorder suddenly from a cold place to a warm place, condensation may
generate on the operating parts and lens and cause abnormal disc playback. If this occurs, do not connect
the plug to the power outlet and wait for two hours. Then insert the disc and try to play back again.
Disc Specifications
Disc Type
❖ DVD-Video
~ A digital versatile disc (DVD) can contain up to 135-minutes of images, 8 audio languages and 32 subtitle
languages. It is equipped with MPEG-2 picture compression and Dolby digital surrounding, allowing you
to enjoy vivid and clear theatre quality images in the comfort of your own home.
~ When switching from the first layer to the second layer of a dual-layered DVD Video disc, there may be
momentary distortion in the image and sound. This is not a malfunction of the unit.
~ Once a DVD-RW/±R recorded in Video Mode is finalised, it becomes DVD-Video.
❖ Audio CD
~ An audio disc on which 44.1 kHz PCM Audio is recorded.
~ Plays CD-DA format audio CD-R and CD-RW discs.
~ The unit may not be able to play some CD-R or CD-RW discs due to the condition of the recording.
❖ CD-R/-RW
~ Use a 700MB (80 minutes) CD-R/-RW disc. If possible, do not use a 800MB (90 minutes) or above disc,
as the disc may not play back.
~ If the CD-R/-RW disc was not recorded as a closed session, you may experience a delay in the early
playback time, all recorded files may not play.
~ Some CD-R/-RW discs may not be playable with this unit, depending on the device which was used to
burn them. For contents recorded on CD-R/-RW media from CDs for your personal use, playability may
vary depending on contents and discs.
❖ DVD±R Disc Playback and Recording
~ Once a DVD±R recorded in Video Mode is finalised, it becomes DVD-Video.
~ You can record onto the available space on the disc and perform editing functions such as giving titles
to discs and programmes and erasing programmes before finalising.
~ When programming is erased from a DVD±R, that space does not become available. Once an area on a
DVD±R is recorded on, that area is no longer available for recording, whether the recording is erased or
not.
~ It takes about 30 seconds for the unit to complete recording management information after recording
finishes.
~ This product optimizes the DVD±R for each recording. Optimizing is carried out when you start recording
after inserting the disc or turning on the unit. Recording onto the disc may become impossible if
optimizing is carried out too many times.
~ Playback may be impossible in some cases due to the condition of recording.
~ This unit can play back DVD±R discs recorded and finalised with a Samsung DVD video recorder. It may
not be able to play some DVD±R discs depending on the disc and the condition of the recording.
❖ DVD-RW Disc Playback and Recording
~ Recording and playback can be performed on DVD-RW discs in both the Video and VR Modes.
~ Once a DVD-RW recorded in both the Video and VR Modes is finalised, you cannot perform additional
recording.
~ Once a DVD-RW recorded in Video Mode is finalised, it becomes DVD-Video.
~ In both modes, playback can be performed before and after finalisation, but additional recording,
deleting and editing can not be performed after finalisation.
English _
● getting started
his unit allows you to record and playback high quality digital video on DVD-RAM/±RW/±R discs or on the
T
HDD.
You can also edit digital images on DVD-RAM/±RW discs or HDD.
getting started
~ If you want to record the disc in VR Mode and then record in V Mode, be sure to execute Format. Be
careful when executing Format because all the recorded data may be lost.
~ A DVD-RW blank disc is initialised to VR Mode when first initialised.
❖ DVD+RW Disc Playback and Recording
~ With DVD+RW discs, there is no difference between DVD-Video format(Video mode) and DVD-Video
Recording format(VR mode).
~ Finalising is generally unnecessary when using a DVD+RW disc.
❖ DVD-RAM Disc Playback and Recording
~ Ensure that the recording mode is set to VR mode. Otherwise, this product will not be able to play the
recording.
~ You cannot play a DVD-RAM in most DVD components due to compatibility issues.
~ Only DVD-RAM standard Version 2.0. discs can be played in this unit.
~ DVD-RAM recorded on this unit may not work with other DVD components. To determine compatibility
with these DVD-RAM discs, refer to the user’s manual for the player.
~ For cartridge type DVD-RAM discs, remove the cartridge and use the disc only.
Disc Copy
Title Copy Specifications
Contents
HDD  DVD
DVD  HDD
Recorded Video Title
Supported
Supported
Copy Protected Title
Not supported
Not supported
Copy Once Title
Move
(Deletes the Title in the HDD after copying)
Not supported
Once “Copy Once programme” has been recorded on the DVD disc, this title cannot be copied to HDD
anymore.
But “Copy Once programme” has been recorded on the HDD, this title can be copied to DVD-RW (VR mode)
with CPRM or DVD-RAM.
Contents Copy Specifications
~
~
~
~
~
Contents
HDD ➔ DVD or USB
DVD ➔ HDD or USB
USB ➔ HDD or DVD
MP3
Supported
Supported
Supported
JPEG(photo)
Supported
Supported
Supported
DivX
Supported
Supported
Supported
CD-DA
Not supported
Supported
Not supported
Disc(CD-DA/CD-R/CD-RW/DVD-RAM, DVD±R(Finalise)/ DVD+RW/DVD-RW(Finalise)) ➔ HDD or USB
HDD ➔ DVD-R, DVD-RW(V) or USB
USB ➔ HDD or DVD-R, DVD-RW(V)
PTP USB is not available when you copy to USB.
If the disc is finalised through Disc Manager, it can be compatible with PC as a disc with a UDF file system.
_ getting started
COPY PROTECTION
• Many DVD discs are encoded with copy protection.
• This product incorporates copyright protection technology that is protected by methods claims of certain U.S. patents and other
intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection
technology must be authorised by Macrovision Corporation, is intended for home and other limited viewing uses only unless
otherwise authorised by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
This HDD & DVD Recorder can allow you to protect the contents of your discs, as described below.
~ Programme-protected : See page 87 “Locking (Protecting) a Title”
~ Disc-protected : See page 102 “Disc Protection”
❋ DVD-RAM/±RW/±R discs that are incompatible with the DVD-VIDEO format cannot be played with this
product.
❋ For more information on DVD recording compatibility, consult your DVD-RAM/±RW/±R manufacturer.
❋ Use of poor quality DVD-RAM/±RW/±R discs may cause following unexpected problems including,
without limitation, recording failure, loss of recorded or edited materials or damage to the HDD & DVD
Recorder.
Disc Format
❖ Using MP3 disc
~ CD-R/-RW, DVD-RAM/±RW/±R, HDD, USB with MP3 files recorded with UDF, ISO9660 or JOLIET
format can be playbacked.
~ Only MP3 files with the “.mp3” or “.MP3” extension can be played.
~ For MP3 files recorded with a VBR(Variable Bit Rates), from 32 Kbps to 320 Kbps, the sound may cut in
and out.
~ Playable bit-rate range is from 56 Kbps to 320 Kbps.
~ Each folder can have up to 500 items including files and sub folders.
❖ Using JPEG disc
~ CD-R/-RW, DVD-RAM/±RW/±R, HDD, USB recorded with UDF, ISO9660 or JOLIET format can be
playbacked.
~ Only JPEG files with the “.jpg” or “.JPG” extension can be displayed.
~ Each folder can have up to 500 items including files and sub folders.
~ MOTION JPEG and progressive JPEG are not supported.
❖ Using DivX disc
~
~
~
~
~
~
~
Disc : CD-R/-RW, DVD-RAM/±RW/±R, HDD, USB
Video File with following extensions can be played. : .avi, .divx, .AVI, .DIVX
DivX Video (Codec) Format : DivX 3.11 DivX 4.x DivX 5.x (without QPEL and GMC)
DivX Audio (Codec) Format : MP3, MPEG1 Audio Layer 2, LPCM, AC3, DTS
Supported subtitle file formats: .smi, .srt, .sub, .psb, .txt, .ass
Each folder can have up to 500 items including files and sub folders.
You cannot play back the disc that is larger than a 720 x 576 pixel resolution.
English _
● getting started
Protection
getting started
Do not use the following discs!
~ LD, CD-G, CD-I, CD-ROM and DVD-ROM discs should not be used in this product.
[Note]
Disc types that can be played : CD/CD-R/-RW/MP3/JPEG/DVD-Video/DVD-RAM/±RW/±R.
For a DVD-RW/±R disc, which has been recorded in Video Mode on another component, it can play only
when finalised.
~ Some commercial discs and DVD discs purchased outside your region may not be playable with this
product. When these discs are played, either “No disc.” or “Please check the regional code of the disc.” will
be displayed.
~ If your DVD-RAM/±RW/±R discs is an illegal copy or is not in DVD video format, it may also not be playable.
❖ Disc compatibility
~ Not all brands of discs will be compatible with this unit.
❖ Compatible USB Devices at host port
~ The USB host port acts as the one of desktop or laptop computer.
❋ This product is compatible with mass storage devices(removable storage devices) and PTP devices
(such as digital still cameras)
~ The USB host port provides USB2.0 connectivity and also backward compatibility with USB1.1 (USB1.0)
devices.
~ Supported devices at host port
❋ Mass Storage Devices
- Digital Still Camera
- MP3 Player
- Memory stick
- Card Reader (One or Multi-slot Card Reader)
- External Hard disk drive : Only supports FAT32 formatted HDD.
- Others removable storage devices.
❋ PTP ( Picture Transfer Protocol ) devices
- Digital Still Camera (in PTP mode among USB connection modes)
~ This product only supports FAT16/32 file system
~ This product supports up to maximum 4 partitions
~ Notice (Caution)
❋ If you happen to use a bad quality USB cable, the USB device might not be recognized.
❋ The compatibility with MP3 players is somewhat restricted.
- This product can playback only mp3 format contents.
- This product does not support the audio contents encrypted by DRM (Digital Right Management)
❋ Either USB hub device or hub extension connectivity is not supported.
❋ There are awfully lots of kinds of USB devices.
Some of the USB devices mentioned above might not be compatible with this product.
In other words, the USB host function of this product does not guarantee the compatibility with all of
USB devices.
_ getting started
~ TPL (Target Peripheral List)
Since this product is not a Windows XP but a embedded USB host system, naturally the supported USB
devices cannot help being limited.
The USB host functionality and compatibility of this product have been proved with following items.
(Except these items , we expect lots of other USB devices will work well with this product)
❋ DSC (Digital Still Camera)
Brand
Samsung
VP-MS11, S800, Pro815, V20, V10, D60, UCA5
Sony
DSC-W50, DSC-R1, DSC-P150, DSC-P200
Canon
IXUS 60, IXUS 600, PowerShot A700, IXUS 700, A620, S80
Panasonic
DMC-FX01, DMC LX1S, DMC-FZ5
Nikon
Coolpix 7900, Coolpix-p3, Coolpix S2
Olympus
C-70 zoom, SP-700, FE5500, C-470Z
Fuji
Finepix-F700
Vendor
Brand
Samsung
YP-T8, YP-U2, YP-T9, YP-P2
i-river
H10, N11, T30, Mplayer
❋ MP3 Player
❋ Others
M
Product
Vendor
Brand
Card Reader
Unicon
UC-601R
PMP
Cowon
A2
Extermal HDD
DATAgram
DHC-350
` Among MP3 players in the list above, those that do not use Mass Storage Class are not supported.
English _
● getting started
Vendor
getting started
getting started
2
connecting & setting up
23
system setup
35
DTV functions
51
10_ getting started
2
3
12
14
15
17
19
22
Warning
Precaution
General Features
Before reading the user’s manual
How to use the HDD & DVD Recorder
Unpacking
Description
Tour of the Remote Control
23 Connecting the HDD & DVD Recorder
24 Additional connections
25 Antenna + HDD & DVD Recorder + External
decoder box + TV
26 Other type of connecting the Video output
cable
28 Other type of connecting the Audio output
cable
31 Connecting HDMI/DVI to a TV
33 Connecting to AV IN 3, DV input jack
34 Connecting to USB Devices
35
35
37
38
41
43
44
45
48
49
On-Screen Menu Navigation
Plug & Auto Setup
Clock Set
Channel Set
Setting up the System Options
Setting up the Language Options
Setting up the Audio Options
Setting up the Video Options
Setting up the Parental Lock
Setting up the Recording Options
51 Basic Functions
52 Guide
playback
54
71
editing
86
reference
106
appendix
108
59
59
60
61
61
62
67
67
69
Region code (DVD-Video only)
Logos of Discs that can be played
Disc types that can be played
Playing a Disc
Using the Disc Menu & Title Menu
Using the Playback Related buttons
Using the INFO button
Selecting the Subtitle Language
Selecting the Soundtracks & Audio
Channels
Changing the Camera Angle
Repeat Play
Zooming-In
Using Markers
Using the Bookmarks
Playing an Audio CD/MP3
Music/Photo Simultaneous Playback
Viewing a Picture
Playing a DivX
71
72
73
75
75
77
78
78
79
81
84
Recordable Discs
Recording Formats
Recording Mode
Unrecordable Pictures
Recording Immediately
Copying from a Camcorder
Making a One Touch Recording (OTR)
Simultaneous Recording and Playback
Time Shift function as a live signal
Making a Timer Recording
Go To Recorded List
86 Basic Editing (Title List)
90 Using the Sort function (Title List)
90 Navigation Menu
91 Select Contents
92 Advanced Editing (Playlist)
97 Copying from Hdd to Dvd Or Vice-versa
98 Copying MP3, JPEG or DivX
100 Changing the name of Music/Photo/DivX file
101 Disc Manager
106 Troubleshooting
108 Specifications
English _11
● getting started
recording
54
54
54
56
56
57
58
58
59
getting started
General Features
This unit allows you to record and playback high quality digital video on DVD-RAM/±RW/±R discs or on the HDD.
You can also edit digital images on DVD-RAM/±RW discs or HDD.
HDD Recording
~ DVD-SH893
You can record up to Approx. 264 hours of video (in EP 8 Hr mode) on the internal 160 GB (gigabyte) hard
disk (HDD).
~ DVD-SH895
You can record up to Approx. 421 hours of video (in EP 8 Hr mode) on the internal 250 GB (gigabyte) hard
disk (HDD).
~ DVD-SH897
You can record up to Approx. 534 hours of video (in EP 8Hr mode) on the internal 320 GB (gigabyte) hard
disk (HDD).
With both recordable DVD and a high-capacity HDD in the same recorder, you have the flexibility to keep
recordings on the HDD for quick access anytime, or record to DVD for archiving or playing on other DVD
players. (See pages 71~74)
Copy between HDD and DVD
You can copy recordings from the HDD to recordable DVD, or from recordable DVD to the HDD.
You can only copy in the same record mode as source title. (See page 97)
Simultaneous Recording and Playback
Playback and recording for both the DVD and the built-in hard disk drive (HDD) are completely independent.
For instance, While Recording to the HDD, play another title on the HDD or play a previously recorded
programme on DVD. While Recording to a DVD, play a previously recorded programme on HDD. (See
pages 78~79)
Automated Quality Adjustment for Timer Recording
If FR mode is selected, the video quality is adjusted automatically so that all video for the scheduled time can
be recorded onto the free disc space. (See page 81)
Copying data from a digital camcorder using a DV input jack
Record DV Device video onto HDD and DVD-RAM/±RW/±R discs using the DV input jack
(IEEE 1394-4pin/4pin). (See page 77)
High quality progressive scan
Progressive scanning provides high resolution and flicker free video. The 10-bit 54-MHz DAC and 2D Y/C
Separating Circuitry provides the highest image playback and recording quality. (See page 46)
DivX Certification
DivX® is a digital video format created by DivX, Inc. This is an official DivX Certified or DivX Ultra
Certified device that plays DivX video.
HDMI (High Definition Multimedia Interface)
HDMI reduces picture noise by allowing a pure digital video/audio signal path from the
HDD & DVD Recorder to your TV.
This HDD & DVD Recorder supports 576p, 720p, 1080i and 1080p.
12_ getting started
Anynet+(HDMI CEC)
Anynet+ is a function that can be used to operate the recorder using a Samsung TV remote
control, by connecting the HDD & DVD Recorder to a SAMSUNG TV using an HDMI Cable.
(This is only available with SAMSUNG TVs that support Anynet+.) (See Page 41)
n
EZ Record Mode
This function allows you initialise and Finalise a disc automatically. (See page 50)
USB Interface for Data Transfer
You can transfer JPEG, MP3 and DivX file of the MP3 player, USB memory or digital camera to a HDD & DVD
RECORDER using the USB interface. You can also copy JPEG, MP3 and DivX file of the HDD & DVD RECORDER
to MP3 player, USB memory or digital camera using the USB interface.
English _13
● getting started
EPG functions
EPG is an Advanced Electronic Programme Guide.
With a Remote Control Unit, you can operate full function.
It has a Auto and Manual Scan facility and Channel Organizing (programmable) facility.
getting started
Before reading the user’s manual
Make sure to check the following terms before reading the user manual.
Icons that will be used in manual
Icon
S
Z
X
C
V
K
L
G
A
D
J
M
N
F
Term
Definition
HDD
This involves a function available on the HDD.
DVD
This involves a function available on DVD or DVD±R/-RW(V) discs that have
been finalised.
RAM
This involves a function available on DVD-RAM.
-RW
This involves a function available on DVD-RW.
-R
+RW
+R
This involves a function available on DVD-R.
This involves a function available on DVD+RW.
This involves a function available on DVD+R.
CD-DA
This involves a function available on a data CD (CD-R or CD-RW).
JPEG
This involves a function available on CD-R/-RW, DVD±R/±RW/-RAM discs
or HDD.
MP3
This involves a function available on CD-R/-RW, DVD±R/±RW/-RAM discs
or HDD.
DivX
This involves a function available on CD-R/-RW, DVD±R/±RW/-RAM discs
or HDD.
Caution
This involves a case where a function does not operate or settings may be
cancelled.
NOTE
One-Touch
button
USB
This involves tips or instructions on the page that help each function
operate.
A function that can be operated by using only one button.
This involves a function available on USB.
About the use of this user’s manual
1) Be sure to be familiar with Safety Instructions before using this product. (See pages 2~9)
2) If a problem occurs, check the Troubleshooting. (See pages 106~107)
Copyright
©2009 Samsung Electronics Co.
All rights reserved; No part or whole of this user’s manual may be reproduced or copied without the prior
written permission of Samsung Electronics Co.
14_ getting started
How to use the HDD & DVD Recorder
Step 1 : Select the disc type or HDD
Please check available disc type before recording.
Step 2 : Format the disc to start recording
Unlike a VCR, the HDD & DVD Recorder starts formatting when an unused disc is inserted. This is required
for the preparation of recording on a disc.
DVD+R DVD+ReWritable
DVD+R DVD+ReWritable
Using the HDD
Formatting unnecessary.
Using a DVD-RAM
This type of disc can be formatted in DVD-Video Recording format (VR mode). You can edit recorded images
and create a playlist in a specific sequence according to your requirements.
Using a DVD-RW
This type of disc can be formatted in either DVD-Video format (V mode) or DVD-Video Recording format (VR
mode). For an unused disc, a message that asks whether to initialise a disc or not. If you select “DVD-VR” or
“DVD-V”, initialising will be started. You can play a Video mode disc on various DVD components. A VR mode
disc allows more varied editing.
Using a DVD-R
Formatting disc is unnecessary and only V Mode Recording is supported. You can play these types of discs
on various DVD components only when they have been finalised.
Using a DVD+RW
For an unused DVD+RW disc, a message that asks whether to format a disc or not. If you select “DVD+RW”,
formatting will be started.
Using a DVD+R
This type of disc will be formatted automatically.
Step 3 : Recording
There are two different recording methods, Direct Recording and Timer Recording. Timer recording is
classified as follows:
Recording mode : XP (high quality mode), SP (standard quality mode), LP (long recording mode), and EP
(extended mode) according to the recording mode. When recording is set in the FR mode, the best quality
picture is recorded with regards to the remaining time on the disc.
Step 4 : Playing
You can select the title you want to play in a displayed menu and then immediately start playback.
A DVD consists of sections, called titles, and sub- sections, called chapters.
English _15
● getting started
If you want to repeatedly record on the same disc or you want to edit the disc after recording, select a
rewritable DVD±RW or DVD-RAM type disc. If you want to save a recording without any changes, choose a
non-rewritable DVD±R. You can record files directly to the built-in HDD or edit a recorded file.
getting started
Step 5 : Editing a recorded disc
Editing on discs is easier than conventional video tapes. The HDD & DVD Recorder supports many different
edit functions, possible only with DVDs and HDD.
With a simple and easy edit menu, you can operate various edit functions, such as delete, copy, rename,
lock, etc., on a recorded title.
Creating a playlist (DVD-RAM/-RW in VR mode, HDD)
With this HDD & DVD Recorder, you can create a new playlist on a disc and edit it without the original, preexisting recording.
Step 6 : Finalising & Playing on other DVD components
To play your DVD on other DVD components, finalising may be necessary. First, finish all editing and
recording operations, then finalise the disc.
When using a DVD-RW disc in VR Mode
DVD discs recorded in VR mode can only be played back in DVD recorders, not players.
When using a DVD-RW disc in Video Mode
The disc should be finalised first to enable playback on anything other than this HDD & DVD Recorder. No
more editing or recording can be made on the disc once it has been finalised.
To enable recording on the disc again, the disc must be unfinalised.
When using a DVD±R disc
You should finalise the disc to play it on a component other than this HDD & DVD Recorder. You cannot edit
or record on the disc once it has been finalised.
M
` You can finalise the disc automatically using EZ Record function. (See page 50)
16_ getting started
Unpacking
Accessories
Check for the supplied accessories below.
RF Cable for TV
Remote Control
Batteries for Remote Control (AAA Size)
Instruction Manual
Quick Guide
Preparing the Remote Control
Install Batteries in the Remote Control
~ Open the battery cover on the back of the remote control.
~ Insert two AAA batteries. Make sure that the polarities (+ and –) are aligned correctly.
~ Replace the battery cover.
If the remote does not operate properly :
~
~
~
~
Check the polarity +/– of the batteries (Dry-Cell)
Check if the batteries are drained.
Check if remote sensor is blocked by obstacles.
Check if there is any fluorescent lighting nearby.
Dispose of batteries according to local environmental regulations. Do not put them in the household
trash.
To determine whether your television is compatible, follow the instructions below.
1. Switch your television on.
2. Point the remote control towards the television.
3. Press and hold the TV STANDBY/ON button and enter the two-figure code corresponding to the brand
of your television, by pressing the appropriate number buttons.
English _17
● getting started
Video/Audio Cable
getting started
Controllable TV Codes
BRAND
BUTTON
BRAND
BUTTON
SAMSUNG
01, 02, 03, 04, 05, 06, 07, 08, 09
NOBLEX
66
AIWA
82
NOKIA
74
ANAM
10, 11, 12, 13, 14, 15, 16, 17, 18
NORDMENDE
72, 73, 75
BANG & OLUFSEN
57
PANASONIC
53, 54, 74, 75
BLAUPUNKT
71
PHILIPS
06, 55, 56, 57
BRANDT
73
PHONOLA
06, 56, 57
BRIONVEGA
57
PIONEER
58, 59, 73, 74
06, 56
CGE
52
RADIOLA
CONTINENTAL EDISON
75
RADIOMARELLI
57
DAEWOO
19, 20, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34
RCA
45, 46
EMERSON
64
REX
74
FERGUSON
73
SABA
57, 72, 73, 74, 75
FINLUX
06, 49, 57
SALORA
74
FORMENTI
57
SANYO
41, 42, 43, 44, 48
06
FUJITSU
84
SCHNEIDER
GRADIENTE
70
SELECO
74
GRUNDIG
49, 52, 71
SHARP
36, 37, 38, 39, 48
HITACHI
60, 72, 73, 75
SIEMENS
71
IMPERIAL
52
SINGER
57
JVC
61, 79
SINUDYNE
57
LG
06, 19, 20, 21, 22, 78
SONY
35, 48
LOEWE
06, 69
TELEAVA
73
LOEWE OPTA
06, 57
TELEFUNKEN
67, 73, 75, 76
MAGNAVOX
40
THOMSON
72, 73, 75
METZ
57
THOMSON ASIA
80, 81
MITSUBISHI
06, 48, 62, 65
TOSHIBA
47, 48, 49, 50, 51, 52
MIVAR
52, 77
WEGA
57
NEC
83
YOKO
06
NEWSAN
68
ZENITH
63
Result : If your television is compatible with the remote control, it will switch off.
It is now programmed to operate with the remote control.
M
` If several codes are indicated for your television brand, try each one in turn until you find one that works.
` If you replace the remote control’s batteries, you must set the brand code again.
Then you can control the television using the following buttons after pressing
the TV button.
Button
TV STANDBY/ON
SOURCE
TV VOL (+ –)
PROG (,.)
TV MUTE
Number
M
Function
Used to switch the television on and off.
Used to select an external source.
Used to adjust the volume of the television.
Used to select the desired channel.
Used to toggle the sound on and off.
Used to input number directly.
` The functions listed above does not necessarily work on all televisions. If you encounter problems, operate the
television directly.
18_ getting started
Description
Front Panel (DVD-SH893/895/897)
● getting started
DISPLAY
Displays the playing status, time, etc.
OPEN/CLOSE button
Opens and closes the disc tray.
SEARCH/SKIP buttons
Goes to the next title/chapter/track or goes back to the previous title/chapter/track.
( Playback mode)
Select TV preset channels. (Stop mode)
PLAY/PAUSE button
Plays a disc or pauses playback.
STOP button
Stops disc playback.
REC button
Starts recording.
HDD/DVD button
Selects HDD/DVD mode.
DISC TRAY
Opens to accept a disc.
USB HOST
Connects to digital still camera, MP3 player, memory stick, Card reader, externl HDD or
other removable storage devices.
10
DV-INPUT
Connects to external digital equipment with a DV jack. (such as a camcorder)
11
AV INPUT 3
Connects to external equipment.
12
STANDBY/ON button
Turns the HDD & DVD Recorder on and off .
English _19
getting started
Rear Panel
Fan
The fan always revolves when the
power is on. Ensure a minimum of 10
cm clear space on all sides of the fan
when installing the product.
In from aerial connector
Connects RF cable from antenna.
VIDEO OUT
Connects the input of external equipment using a Video cable.
AV2(EXT) INPUT
SCART Connector
Connects to equipment having SCART output jack.
HDMI OUT
Connects to equipment having HDMI input.
DIGITAL AUDIO
OUT(OPTICAL)
Connects to an amplifier having a digital optical audio input jack.
AV1(TV) OUTPUT
SCART Connectora
Connects to equipment having SCART input jack.
AUDIO OUT
Connects to the audio input of external equipment using audio cables.
COMPONENT VIDEO
OUT
Connects to equipment having Component video input.
Out to TV connector
Connects RF cable to TV antenna input.
20_ getting started
Front Panel Display
● getting started
In Disc Indicator
Lights status icon.
DVD VIEW Indicator
Lights when DVD mode is selected.
HDD VIEW Indicator
Lights when HDD mode is selected.
USB VIEW Indicator
Lights when USB mode is selected.
TIMER Indicator
Lights to indicate the timer record mode.
HDMI Indicator
Lights to indicate when HDMI is connected and HDMI resolution status.
REC Indicator
Lights in the record mode.
STATUS Indicator
Playing time/clock/current status indicator.
English _21
getting started
Tour of the Remote Control
Your HDD & DVD Recorder remote control will work with Samsung televisions and compatible brands.
Installing batteries in the Remote Control
1.Lift the cover at the back of the
remote control upward as shown.
2.Install two AAA size batteries.
Make sure to match the “+” and “–”
ends of the batteries with the diagram
inside the compartment.
STANDBY/ON button
SOURCE button
Select input signal in external input mode (PROG, AV1, AV2,
AV3 or DV input).
DTV/ANALOG button
Select Digital/Analogue broadcasting.
3.Replace the cover.
Assuming typical TV usage, the
batteries last for about one year.
OPEN/CLOSE button
To open and close the disc tray.
TV STANDBY/ON button
SELECT
(TV, USB, DVD, HDD)
NUMBER buttons
TV/DVD button
COPY button
REPEAT button
Allows you to repeat a title, chapter, track or disc.
Playback-related Buttons
Forward/Rewind, Search, Skip, Stop, Play/Still.
TV MUTE button
In TV mode, this operates as sound mute.
TV VOL button
TV volume adjustment.
Use this to select a TV programme.
MENU button
AUDIO button
(INFO) button
RETURN button
Brings up the HDD & DVD Recorder’s setup menu.
Press to display the programme information box in the screen
when you use DTV. Allows access to common functions of the
HDD & DVD Recorder. (See pages 58~60.)
A, B, C, D button
Allows access to various function of HDD & DVD RECORDER.
TITLE LIST/DISC MENU button
Use this to enter the View Recording list/disc menu.
SUBTITLE button
Press this to switch DVD’s subtitle language. When you use
DTV, press this button to select the subtitle.
TEXT button
When you use DTV, press this button to select the Teletext OSD.
TV/RADIO button
In DTV mode, press this to switch TV or Radio mode
REC button
Use to make a recording on HDD/DVD-RAM/±RW/±R discs.
GUIDE button
Press this to switch programme guide.
22_ getting started
PROG button
Press this to switch DVD's audio language.
When you use DTV, press this button to select the audio.
OK/DIRECTION buttons
($%_ + buttons)
EXIT button
MARKER button
Use this to bookmark a position while playing a disc.
PLAY LIST/TITLE MENU button
Use this to return to the Title menu, or to view the recorded
files list.
TIMER button
Press to directly enter the Timer Recording Mode menu.
FAV LIST button
When you use DTV, press this button to switch between favorite list.
REC PAUSE/TIME SHIFT button
Use this to pause during recording. In HDD mode, use this to
operate Time shift function.
REC MODE button
Use this to set the desired recording time and picture quality.
(XP/SP/LP/EP).
connecting & setting up
Connecting the HDD & DVD Recorder
This section involves various methods of connecting the HDD & DVD Recorder to other external components and
required initial setting modes.
1. Connect the RF cable as shown.
2. Connect one end of the SCART cable to the AV1 socket on the rear of the HDD & DVD Recorder.
3. Plug the other end into the appropriate connector on the television.
4. Plug in the HDD & DVD Recorder and TV
5. Turn on the HDD & DVD Recorder and TV.
6. Press the SOURCE button on your TV remote control until the Video signal from the HDD & DVD
Recorder appears on the TV screen.
To ANT IN
To TV
SCART cable
(not included)
RF Cable
To ANT INPUT
M
` The RF cable connection of this product sends only signals of TV. You must connect SCART cable or Audio/Video
cables to watch output from your HDD & DVD Recorder.
English _23
● connecting & setting up
You can connect your HDD & DVD Recorder to the television using the SCART cable if the appropriate input
is available on the television.
connecting & setting up
Additional connections
You can connect your HDD & DVD Recorder to a External device (VCR/Satellite receiver).
SCART cable
(not included)
External device (VCR/Satellite receiver)
1
SCART cable
(not included)
- DVD mode
1. Connect the AV2 connector of HDD & DVD Recorder and External device (VCR/Satellite receiver) using a
SCART cable.
2. Connect the AV1 connector to the SCART AV connector on TV.
3. Turn on the HDD & DVD Recorder, External device (VCR/Satellite receiver) and TV.
4. Set Input mode on AV2.
- TV mode
1. Press the TV/DVD button on remote control, then “TV” appear on Front display.
(or turn off HDD & DVD Recorder.)
2. You can watch programmes from a satellite or digital tuner connected to this HDD & DVD Recorder, even
when the HDD & DVD Recorder is turned off.
24_ connecting & setting up
Antenna + HDD & DVD Recorder + External decoder box +
TV
If you connect external decoder box to HDD & DVD Recorder, you can record scrambled channels (CANAL+or
Premiere broadcasts) received through the built-in TV tuner in HDD & DVD Recorder.
SCART cable
(not included)
Wall
RF cable
RF cable
SCART cable
(not included)
1. Connect RF antenna cables as shown.
2. Connect the AV1 connector on this recorder to the SCART AV connector on TV using a SCART cable.
3. Connect the AV2 connector to a SCART AV connector on decoder box.
4. To watch or record PAY-TV Canal Plus programmes, set your HDD & DVD Recorder to receive the
channels using the on-screen display. (Refer to page 38)
English _25
● connecting & setting up
3
DECODER
connecting & setting up
Other type of connecting the Video output cable
There are several ways to output video signal not using scart cables. Select one of the following video connecting
that best suits you below.
~ Case 1 : Connecting to a Video (Composite) output jack
~ Case 2 : Component Video output jacks
Component video and Progressive Output Modes
~ Component video output are available only if your TV supports Component video input, respectively.
If Component video output does not work, check the TV connections and the TV input selection settings.
~ Compared to standard interlaced video, progressive scan doubles the amount of video lines fed to your TV,
resulting in a more stable, flicker-free, clear image than interlaced video. This is only available with TVs that
support progressive scan.
~ Progressive Scan Output (576p)
Consumers should note that not all high definition television sets are fully compatible with this product and
may cause artifacts to be displayed in the picture, in case of 576 progressive scan picture problems, It is
recommended that the user switch the connection to the ‘standard definition’ output. If there are questions
regarding our TV set compatibility with this model 576p HDD & DVD Recorder, please contact our
customer service centre.
Case 1 : Connecting to a Video (Composite) output jack
1. Connect a video (Yellow) cable between the VIDEO (yellow) OUT jack on HDD & DVD Recorder and
VIDEO (yellow) INPUT jack on your TV (or AV amplifier).
~ You will enjoy regular quality images.
2. Connect audio cables (white and red) between the AUDIO OUT jacks on the HDD & DVD Recorder and
AUDIO IN jacks on TV (or AV amplifier). (See pages 28~33)
Video/Audio cable
Yellow
Red
White
26_ connecting & setting up
Case 2 : Component Video output jacks
1. Connect Component video cables(not supplied) between the COMPONENT OUT(Y, PB, PR) jacks on HDD
& DVD Recorder and COMPONENT IN(Y, PB, PR) jacks on your TV.
~ You will enjoy high quality and accurate colour reproduction images.
2. Connect audio cables (white and red) between the AUDIO OUT jacks on the HDD & DVD Recorder and
AUDIO IN jacks on TV (or AV amplifier). (See pages 28~33).
3. After connecting, refer to the page 46.
Green
M
Blue
Red
` Make sure that the colour coded connections match. The Y, PB, PR component output jacks of your HDD & DVD
Recorder must be connected to the exact corresponding component input jacks on your TV.
` Progressive setting is only available when the Video Out is set to Component.
(See page 46)
English _27
● connecting & setting up
Component cable
(not included)
connecting & setting up
Other type of connecting the Audio output cable
There are several ways to output audio signal not using scart cables. Select the audio connection that best suits you
below.
~ Case 1 : Connecting to your TV
~ Case 2 : Connecting to a stereo amplifier with AV output jacks
~ Case 3 : Connecting to an AV amplifier with a digital output jack
Manufactured under license under U.S. Patent #: 5,451,942 & other U.S. and worldwide patents issued & pending.
DTS and DTS Digital Out are registered trademarks and the DTS logos and Symbol are trademarks of DTS, Inc.
© 1996-2009 DTS, Inc. All Rights Reserved.
Manufactured under licence from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby
Laboratories.
Case 1 : Connecting to your TV
If your TV has audio input jacks, use this connection.
Component cable
(not included)
Yellow
Red
White
28_ connecting & setting up
Case 2 : Connecting to a stereo amplifier with AV output jacks
If your stereo amplifier only has AUDIO INPUT jacks (L and R), use the AUDIO OUT jacks
● connecting & setting up
Audio cable
Red
White
Front(L)
speaker
Front(R)
speaker
English _29
connecting & setting up
Case 3 : Connecting to an AV amplifier with a digital output jack
If your AV amplifier has a Dolby Digital, MPEG2 or DTS decoder and a digital input jack, use this connection.
To enjoy Dolby Digital, MPEG2 or DTS sound, you will need to set up the audio settings. According to your
amplifier, connect to an optical cable. (See pages 44~45)
Optical cable
(not included)
Rear(R)
Rear(L)
Front(L)
Front(R)
Subwoofer
30_ connecting & setting up
Centre
Connecting HDMI/DVI to a TV
If your TV has a HDMI/DVI input, connect HDMI/DVI Adapter cable to a TV. You will enjoy the best quality images
and sounds.
~ Case 1 : Connecting to a TV with HDMI Jack
~ Case 2 : Connecting to a TV with DVI Jack
Case 1 : Connecting to a TV with HDMI Jack
HDMI-HDMI cable
(not included)
M
` If the HDD & DVD Recorder is connected to your TV in HDMI 1080p output mode, you must use High
speed(category2) HDMI cable.
English _31
● connecting & setting up
~ Using the HDMI cable (not supplied) connect the HDMI OUT jack on the rear of the HDD & DVD Recorder
to the HDMI IN jack of your TV.
~ Press the input selector on your TV remote control until the HDMI signal from the HDD & DVD Recorder
appears on your TV screen.
connecting & setting up
Case 2 : Connecting to a TV with DVI Jack
~ Using a DVI Adapter cable (not supplied), connect the HDMI OUT jack on the rear of the HDD & DVD
Recorder to the DVI IN jack of your TV.
~ Using the audio cables, connect the AUDIO (red and white) OUT jacks on the rear of the HDD & DVD
Recorder to the AUDIO (red and white) IN jacks of your TV. Turn on the HDD & DVD Recorder and TV.
~ Press the input selector on your TV remote control until the DVI signal from the HDD & DVD Recorder
appears on your TV screen.
HDMI-DVI cable
(not included)
Red
J
White
` To use an HDMI cable (not supplied), make the Audio/Video connection before plugging in the power cord or after
finishing the “Plug & Auto Setup.” Do not connect the HDMI cable while the “Plug & Auto Setup” is progressing.
` Progressive scan automatically activates when HDMI is connected.
` If TV/HDMI Receiver does not support DTS, Audio output is not available when you play disc in DTS format.
` You can switch from the HDMI output to other output only in stop mode.
` If you use an HDMI cable to connect a Samsung TV to the HDD & DVD Recorder, you can operate the recorder using
the TV remote control.
(This is only available with SAMSUNG TVs that support Anynet+(HDMI CEC).) (See pages 41~42)
` Please check the ' logo (If your TV has an ' logo, then it supports Anynet+ function.)
M
` HDMI (High Definition Multimedia Interface)
HDMI is an interface to enable the digital transmission of video and audio data with just a single connector. Since
HDMI is based on DVI, it is completely compatible with DVI. The only difference between HDMI and DVI is that HDMI
supports multi-channel audio. Using HDMI, the HDD & DVD Recorder transmits a digital video and audio signal and
displays a vivid picture on a TV having an HDMI input jack.
32_ connecting & setting up
` HDMI connection description
HDMI connector - Both uncompressed video data and digital audio data (LPCM or Bit Stream data).
- Though the HDD & DVD Recorder uses a HDMI cable (not supplied), the HDD & DVD Recorder outputs only a pure
digital signal to the TV.
- If TV does not support HDCP (High -bandwidth Digital Content Protection), snow noise appears on the screen.
` Why does Samsung use HDMI?
` What is the HDCP?
HDCP (High-bandwidth Digital Content Protection) is a system for protecting DVD content outputted via HDMI from
being copied. It provides a secure digital link between a video source (PC, DVD. etc) and a display device (TV,
projector. etc). Content is encrypted at the source device to prevent unauthorised copies from being made.
Connecting to AV IN 3, DV input jack
This allows you to connect your HDD & DVD Recorder to other external devices and view or record their outputs.
~ Case 1 : Connecting a VCR, Set-Top Box(STB), DVD player or Camcorder to the AV IN 3 jacks
~ Case 2 : Connecting a DV Device to the DV IN jack
Case 1 : Connecting a VCR, Set-Top Box(STB), DVD player or
Camcorder to the AV IN 3 jacks
Connecting a VCR or external device to AV IN 3 jacks of the HDD & DVD Recorder. You can record from
connected equipment (VCR, STB, DVD player or Camcorder).
Yellow
M
Red
White
` AV IN 3 selection will be automatically done.
If the input is not selected automatically, use SOURCE button to select proper input.
` Copy protected content cannot be recorded.
English _33
● connecting & setting up
Analogue TVs require an analogue video/audio signal. However, when playing a DVD, the data transmitted to a TV is
digital. Therefore either a digital-to-analogue converter (in the HDD & DVD Recorder) or an analogue-to-digital
converter (in the TV) is required. During this conversion, the picture quality is degraded due to noise and signal loss.
HDMI technology is superior because it requires no D/A conversion and is a pure digital signal from the HDD & DVD
Recorder to your TV.
connecting & setting up
Case 2 : Connecting a Camcorder to the DV IN jack
If your digital camcorder has a DV output jack, connect it to the DV input jack of your HDD & DVD Recorder.
Camcorder
M
` If the input is not selected automatically, use SOURCE button to select proper input.
Connecting to USB Devices
This allows you to connect your HDD & DVD RECORDER to USB devices.
Connecting a USB memory, MP3 player, Digital Camera to the USB HOST.
MP3 Player
Digital Camera
M
` Disconnecting the USB cable during the data transfer will stop the communication and may damage data stored in
the memory.
` When data communication is disrupted due to static electricity, magnetic field or other reason, restart the
programme or try to disconnect / connect the USB Cable again.
34_ connecting & setting up
system setup
On-Screen Menu Navigation
1. $%, _ + buttons
Press these buttons on the remote control to move the selection
bar $%, _ + to cycle through the menu options.
HDD & DVD RECORDER
. OK button
Press this button on the remote control to confirm any new
settings.
. RETURN button
Press this button on the remote control to return to the Previous
menu screen displayed or to exit the on-screen menu.
Library
HDD
Library
Title ►
Guide
DivX
►
Music
►
Photo
►
Channel
Timer Record
Disc Manager
Setup
m MOVE
sSELECT
rRETURN
eEXIT
. EXIT button
Press this button to exit the on-screen menu.
Plug & Auto Setup
Your HDD & DVD Recorder will automatically set itself up when it is plugged in for the first time. TV stations and
clock will be stored in memory. The process takes a few minutes. Your HDD & DVD Recorder will then be ready for
use.
1. Connect the RF cable as indicated on page 23.
(Connecting Your HDD & DVD Recorder to the TV Using the RF Cable and scart cable.)
To use HDMI cable (not supplied), make the Audio/Video connection before plugging in the power cord or
after finishing the “Plug & Auto Setup.” Do not connect the HDMI cable while the “Plug & Auto Setup” is
progressing.
. Plug the HDD & DVD Recorder into the mains. “AUTO” in the front panel
display flickers.
. Press the OK or ► button, then Country option display.
Press the $% buttons to select the desired country option, then press
the OK button.
. Press the OK or ► button, then Language option display.
Press the $% buttons to select the desired language option,
then press the OK button.
. Press the OK or ► button, then Time Zone option display.
Press the ◄ ► buttons to select the desired time zone option.
Press the $% buttons to select OK, then press the OK button.
M
Initial Installation
Country
: United
SwissKingdom
TurkeyKingdom
: United
Greece
: GMT
- 12:00
Hungary
Poland
: Off
Czech
Slovakia
Others
OK
Language
Time Zone
Daylight Saving Time
` If you select a country, the time zone will be automatically set
accordingly.
Initial Installation
Country
Time Zone
Language
◄
Time Zone
Daylight Saving Time
: United Kingdom
United
GMT +:01:00
Kingdom
►
: GMT - 12:00
OK
: Off
►
►
►
►
OK
English _35
● system setup
The on-screen menus allow you to enable or disable various functions on your HDD & DVD Recorder.
Press the MENU button to open the on-screen menu and then use the following buttons to navigate through the on
screen menus.
system setup
. Press the OK or ► button, then Daylight Saving Time option
display.
Press the $% buttons to select On or Off, then press the OK
button.
Initial Installation
. Press the % button to select OK, then press the OK button.
Digital auto scan will be started.
Country
: Others
►
Language
: English
►
Time Zone
: GMT + 00:00
Off
: Off
On
Daylight Saving Time
. Press the OK button.
Analogue auto scan will be started.
Auto Scanning
Digital 578.000MHz, BW:8MHz, FFT:Auto
10. After auto channel scan is completed, auto clock setting will be started automatically in 10 seconds. If you want to start auto clock setting immediately, press OK button.
DTV
DTV
Radio
5
5
5
OK
Progress
Signal status
Setup” is fixed already. So if you want to change this fixed one, you
can change it by Presetting the Stations in OSD “Channel Set Manual Setup (Analogue)” menu. (See pages 38~39)
eEXIT
Auto Scanning
ATV
` Auto setup function can be performed by pressing STOP ( ) on the
unit continuously for 5 seconds or more during power off with no
disc inserted.
1. Check the date and time.
~ If it is : Correct, press OK button then the date and time will be
saved. If you don’t press the OK button, the date and time will
be saved automatically after 5 seconds.
~ If it is : Incorrect, input correct Month, Day, Year, Hour or
Minute using $%, _ + buttons or number buttons. Press OK
button then the date and time will be saved. When you need to
change clock setting, you can set up it manually.
Radio
5
Your digital receiver found
TF1
NRJ12
LCI
Eurosp
TPS ST
11. Wait until current date and time are displayed automatically. If you want to exit auto clock setting, press MENU button.
M
3
PR
CH
Name
Decoder
1
2
3
004
---
072
----
----
----
OFF
OFF
OFF
Progress
eEXIT
Please wait. Now setting the clock.
If you want to exit clock setting,
press the [MENU] button.
Clock Set
mo.
da.
yr.
hr.
JAN
01
2009
12
Tuesday
36_ system setup
►
OK
. After auto channel scan is completed, the message "Your digital
receiver found" will be displayed.
` Now, HDD & DVD Recorder is ready for use. Function for “Plug & Auto
►
min. Auto
00
On
Clock Set
1. With the unit in Stop mode, press the MENU button.
HDD & DVD RECORDER
. Press the $% buttons to select Setup, then press the OK or ►
button.
Setup
HDD
. Press the $% buttons to select Clock Set, then press the OK or
► button.
Library
System ►
Guide
Clock Set
►
Language
►
Channel
Timer Record
Disc Manager
Setup
m MOVE
►
Video
►
Parental Lock
1
►
Recording
►
sSELECT
rRETURN
eEXIT
Time Zone
To setup, follow steps 1~3.
. Press the ▲▼ buttons to select Time Zone, then press the OK
or ► button.
Select the time zone of your area using the _ + buttons, then
select OK using ▲▼ button.
HDD & DVD RECORDER
Clock Set
HDD
Library
Guide
Channel
Time Zone Time Zone
Manual Clock Set
◄
GMT + 01:00 Daylight
Saving
►
►
►
►
OK
Timer Record
Disc Manager
Setup
m MOVE
sSELECT
rRETURN
eEXIT
❖ GMT (Greenwich Mean Time) Table
Country
GMT
City
United Kingdom, Portugal
GMT+00:00
Dublin, Edinburgh, London, Lisbon, Casablanca
France, Austria, Belgium, Demark, Deutschland,
Netherlands, Italy, Norway, Spain, Sweden, Swiss,
Hungary, Czech
GMT+01:00
Berlin, Stockholm, Rome, Vienna, Paris, Madrid, Prague,
Warsaw, Brussel, Copenhagen, Oslo, Bern, Budapest,
Warszawa, Prague
Finland, Turkey, Greece
GMT+02:00
Athens, Helsinki, Istanbul, Cairo, Eastern Europe, Pretoria,
Israel
Manual clock set
To setup, follow steps 1~3.
. Press the ▲▼ buttons to select Manual Clock Set, then press
the OK or ► button.
Use the ▲▼◄ ► buttons to input Time, Date or Year.
Use number buttons to input clock data directly.
HDD & DVD RECORDER
Clock Set
HDD
Library
Guide
Channel
. Press the OK button, then the date and time will be saved.
If you don’t press the OK button, it will not be saved.
Timer Record
mo. da.
JAN
01
yr.
2009
hr. min. Auto
12
00
On
Tuesday
Disc Manager
Setup
M
< MOVE
sSELECT
rRETURN
eEXIT
` You must have the RF cable connected to set the Auto Clock. (See page 23)
` The DVD Recorder automatically sets the clock according to the time signal broadcast between the channels PR1 to
PR5. If there is no clock in the analogue broadcast, the clock will be searched automatically in the DVB-T. If you do
not need the Auto clock set function, select Off.
` If there is a difference between the time information of analogue and the one of digital, you may not be available to
the contents of DVB-T normally.
English _37
● system setup
Audio
system setup
Daylight Saving Time
To setup, follow steps 1~3 in page 37.
. Press the $% buttons to select Daylight Saving Time, then
press OK or + button.
HDD & DVD RECORDER
Clock Set
HDD
Library
. Select the Off or On using the $% buttons, then press the OK or
+ button.
Guide
Time Zone ►
Manual Clock Set
►
Daylight Saving TimeOff Channel
✔►
On
Timer Record
Disc Manager
Setup
m MOVE
sSELECT
rRETURN
eEXIT
Channel Set
This menu consist of 5 sub-menus (Channel List (Digital), Favorite List (Digital), Auto Scanning, Manual Scanning
(Digital), Manual Setup (Analogue)).
Auto Scanning
This function allows you to download of the channels automatically from the programmed load.
1. With the unit in Stop mode, press the MENU button.
. Press the $% buttons to select Channel, then press the OK or ►
Auto Scanning
button.
Country
:
Others Channel type
:
All . Press the $% buttons to select Auto Scanning, then press OK
Scan Mode
:
All Start frequency
:
CH 21/474000kHz or + button.
End frequency
:
CH 69/858000kHz The message "Auto Scanning will remove all channels. Press [OK]
Start
Cancel
to continue,[RETURN] to exit." will be displayed.
. Press the OK button, then press the $%_ + buttons to select
desired options.
(Channel Type : Digital)
~ Country : Press the _ + buttons to select desired country.
~ Channel type : P
ress the _ + buttons to select Digital,
Auto Scanning
Analogue or All. (If you select Analogue, you can
Digital 578.000MHz, BW:8MHz, FFT:Auto
not select the Scan Mode, Start frequency and
DTV
Radio
5
5
Your digital receiver found
End frequency.)
TF1
DTV
Radio
5
5
NRJ12
LCI
~ Scan Mode : - Only Free : Receives signals except for the
OK
Eurosp
TPS ST
scrambled signal.
Progress
- All : Receives signals including the scrambled
Signal Status
signal.
eEXIT
~ Start frequency/End frequency : It is changed automatically when the country is selected.
(Channel Type : Analogue)
. Press the $% button to select Start, then press OK button.
Auto Scan will be started.
Auto Scanning
◄
►
◄
►
◄
►
◄
►
◄
►
ATV
3
PR
CH
Name
Decoder
1
2
3
004
---
072
----
----
----
OFF
OFF
OFF
Progress
M
` You can select RADIO mode by pressing the TV/RADIO button on the remote control.
This button used to toggle the TV and RADIO mode.
38_ system setup
eEXIT
Manual Scanning (Digital)
To tune-in new channels, the HDD & DVD Recorder has been provided with the option Manual Scan where
the channel data can be entered by user.
To setup, follow steps 1~2 in page 38.
. Press the $% buttons to select Manual Scanning (Digital),
then press OK or + button.
Channel
HDD
Library
Channel List (Digital) Guide
Favorite List (Digital)
►
Auto Scanning
►
Manual Scanning (Digital)
►
Manual Setup (Analogue)
►
Channel
Timer Record
►
Disc Manager
Setup
m MOVE
sSELECT
rRETURN
eEXIT
Manual Scanning (Digital)
Country
Channel type
Scan Mode
Channel Number
Frequency
Bandwidth
Signal status 50%
:
:
:
:
:
:
Others Digital All CH 5 177500kHz 8MHz ◄
◄
◄
◄
Start
►
►
►
►
Cancel
Manual Setup (Analogue)
To setup, follow steps 1~2 in page 38.
. Press the $% buttons to select Manual Setup (Analogue), then
press OK or + button.
. Press the $% buttons to select a PR(programme) you wish to
edit, delete, or swap, then press the COLOUR button.
Select Edit, Delete or Swap.
~ In case of Edit (RED(A) button) : You can add or edit
PR(programme) information. After change PR informations (CH,
Name, Decoder, MFT), select Save, then press the OK button.
- CH : Tune the channel using _ + buttons.
- Name : Display station name automatically detected in
broadcasting signal. If not detected, you can edit
name by using $%_ + buttons.
- Decoder : If you set on, you can record scrambled channels
using external decoder box. Before setting on,
refer to connecting external decoder box in the
page 25.
- MFT (Manual Frequency Tunning) :
You can tune up the channel frequency better using _ +
buttons.
~ In case of Delete (GREEN(B) button) : the channel information
of selected PR(programme) will be removed.
~ In case of Swap (YELLOW(C) button) : You can swap the
channel information of two PR(programme). For example, if you
wish to swap PR2 and PR5, select swap at PR2, then press the
OK button at PR5.
HDD & DVD RECORDER
Channel
HDD
Library
Channel List (Digital) Guide
Favorite List (Digital)
►
Auto Scanning
►
Manual Scanning (Digital)
►
Manual Setup (Analogue)
►
Channel
Timer Record
►
Disc Manager
Setup
m MOVE
sSELECT
rRETURN
eEXIT
Manual Setup (Analogue)
PR
CH
Name
Decoder
01
02
03
04
05
06
07
---
---
---
---
---
---
---
----
----
----
----
----
----
----
---------------
A
Edit
B
Delete
C
Swap
Manual Setup (Analogue)
PR
CH
Name
Decoder
MFT
01
◄
►
Off
Save
m MOVE
sSELECT
English _39
● system setup
. Select the Channel Number which you want to find using _ +
buttons.
Select Frequency and input the Frequency of the channel you
want to find by pressing the number button.
Select Bandwidth which you want to find using _ + buttons.
When the valid frequency is input, the bandwidth is selected
automatically. You can select the value of 6,7 or 8 MHz. After
select option. Press OK button to start the scanning process.
HDD & DVD RECORDER
system setup
Channel List (Digital)
This function is possible in DVB-T mode only.
This function is used to edit the favorite channel list or delete the channel.
To setup, follow steps 1~2 in page 38.
. Press the $% buttons to select Channel List (Digital), then
press OK or + button.
. To delete a channel from the Channel List (Digital), press the
RED(A) button. Press the OK button to watch that channel.
. To renumber a channel from the DTV channel list, press the
GREEN(B) button. The message "Enter new channel number."
will be displayed.
DTV channel list
001 SVT1
002 SVT2 ABC
003 TV3
004 TV4 Stockholm
005 Kanal 5
006 TV6
007 Eurosport
Remove
Renumber
[/] Page
r Return
. Press the number buttons to enter a new channel number.
M
` Press OK button in the DVB-T view to display the Channel List
(Digital).
` You can select RADIO mode by pressing the TV/RADIO button on the
remote control.
This button used to toggle the TV and RADIO mode.
` If you renumber a scheduled channel, the channel will be removed
Radio channel list
045 YLE PEILI
046 YLEN KLASSINEN
047 YLE FSR+
048 YLEMONDO
049 YLE X3M
Remove
Renumber
[/] Page
r Return
from the scheduled list.
` If a new channel is added or a lesser number of channels are received
than the TV channels, run Auto Scanning again.
Favorite List (Digital)
This function is possible in DVB-T mode only.
You can immediately register the present channel to the Favorite List (Digital).
To setup, follow steps 1~2 in page 38.
. Press the $% buttons to select Favorite List (Digital), then press
OK or + button.
. To add the current channel to the Favorite Lists (Digital), press the
GREEN(B) button.
To delete a favorite channel from the Favorite List (Digital), press
the RED(A) button.
Press the OK button to watch that channel.
40_ system setup
Favorite List(Digital)
001 TF1
002 NRJ12
Remove
Add Current
[/] Page
r Return
Setting up the System Options
This function allows you to setup the system setting.
1. With the unit in Stop mode, press the MENU button.
HDD & DVD RECORDER
. Press the $% buttons to select Setup, then press the OK or +
button.
Library
Guide
. Press the $% buttons to select System, then press the OK or +
button.
Channel
Timer Record
Disc Manager
Auto Power Off
: Off Power Save
: Off
►
Anynet+ (HDMI CEC) : Off
►
►
DVB-T Auto Subtitle : On
►
Touch Key Sound
: Off
►
DivX(R) Registration
►
Setup
m MOVE
sSELECT
rRETURN
eEXIT
Auto Power Off Setting
This feature automatically turns off your HDD & DVD Recorder, if you do not press any button for the selected time.
1. Press the $% buttons to select Auto Power Off, then press the
OK or + button.
HDD & DVD RECORDER
System
HDD
Library
Auto Power Off
: Off
Off
✔
. Press the $% buttons to select the desired item, then press the
2:Hours
Power Save
Off
Guide
OK or + button.
Anynet+ (HDMI CEC) 6:Hours
Off
Channel
DVB-T Auto Subtitle : On
~ Off : Auto power off is disabled.
Timer Record
Touch Key Sound
: Off
DivX(R) Registration
Disc Manager
~ 2 Hours : HDD & DVD Recorder will automatically turn off for Setup
2 hours after the last button is pressed.
m MOVE
sSELECT
rRETURN
eEXIT
~ 6 Hours : HDD & DVD Recorder will automatically turn off for 6 hours after the last button is pressed.
~ If the turn off time set with the Auto Power off function is reached during playback or recording, the
device will operate until the playback or recording is finished.
►
►
►
►
►
M
►
` If you off and on the HDD & DVD Recorder, the option will be returned to default.
Power Save Setting
~ On: If it is set to On and you turn off the HDD & DVD recorder, the
recorder enters the Power Save and the front panel display
goes off.
~ Off : Does not set to Power Save. Normally select OFF mode.
HDD & DVD RECORDER
System
HDD
Library
Guide
Channel
Timer Record
Disc Manager
Auto Power Off
: Off Power Save
: Off
Off
►
✔►
Anynet+ (HDMI CEC) On
: Off
►
DVB-T Auto Subtitle : On
►
Touch Key Sound
: Off
►
DivX(R) Registration
►
Setup
m MOVE
sSELECT
rRETURN
eEXIT
Anynet+ (HDMI CEC)
Anynet+ is a function that can be used to operate the recorder using a Samsung TV remote control, by
connecting the HDD & DVD Recorder to a SAMSUNG TV using an HDMI Cable. (See pages 31~32) (This is
only available with SAMSUNG TVs that support Anynet+.)
1. Press the $% buttons to select Anynet+ (HDMI CEC), then
press the OK or + button.
Anynet+ (HDMI CEC) items will be displayed.
HDD & DVD RECORDER
System
HDD
Library
Guide
. Press the $% buttons to select On, then press the OK or +
button.
Channel
Timer Record
Disc Manager
Setup
m MOVE
Auto Power Off
: Off Power Save
: Off
Anynet+ (HDMI CEC) Off
: Off
►
►
✔►
DVB-T Auto Subtitle On
: On
►
Touch Key Sound
: Off
►
DivX(R) Registration
►
sSELECT
rRETURN
eEXIT
English _41
● system setup
. Press the $% buttons to select the desired system option, then
press the OK or + button.
. Press the ▲▼ buttons to select the desired item, then press the
OK or + button.
System
HDD
system setup
For using Anynet+ (HDMI CEC)
1. Connect the HDD & DVD Recorder to a Samsung TV with an HDMI cable. (See pages 31~32)
2. Set the Anynet+ (HDMI CEC) to “On” on your HDD & DVD Recorder. (See page 41)
3. Set the Anynet+ function on your TV.
(See the TV instruction manual for more information.)
~ You can operate the HDD & DVD Recorder by using TV remote control.
(TV buttons that can be used to control the HDD & DVD Recorder :
,
, ~ , REC and colour buttons.)
,
,
~ When you press Anynet+ button on the TV’s remote control, the < TV Menu >
OSD to the left will appear.
- Select Device : Use this option to select device.
DVDR
View TV - Record : Use this option to start recording or stop recording.
Select Device
Record
- Menu on Device : Same as MENU ( ) button on the
Menu on Device
HDD & DVD Recorder remote control.
Device Operation
Receiver : Off
- Device Operation : Same as INFO ( ) button on the
Setup
HDD & DVD Recorder remote control.
> Move
eExit
M
,
,
,
,
,







sEnter
` By pressing the Power On button of the recorder while watching TV,
the TV screen will change to the play screen.
` If you power on a DVD recorder when the TV power is off, the TV will power On.
` If you turn the TV off, the HDD & DVD Recorder will power off automatically. (When the HDD & DVD Recorder is
recording, it can’t be powered off.)
` If you change the HDMI to other sources (Composite, Component, RF... etc) in TV while playing the DVD disc, the
HDD & DVD Recorder will stop playing. But the HDD & DVD Recorder may keep the DVD disc Recording.
DVB-T Auto Subtitle
~ On : The subtitle is shown automatically when receiving the
DVB-T.
~ Off : The function is cancelled.
HDD & DVD RECORDER
Library
Guide
M
System
HDD
Channel
` It is available when receiving the DVB-T that has a subtitle.
Auto Power Off
: Off ►
Power Save
: Off
►
Anynet+ (HDMI CEC) : Off
Timer Record
DVB-T Auto Subtitle Off
: On
Touch Key Sound On
: On
Disc Manager
DivX(R) Registration
►
►
✔►
►
Setup
m MOVE
sSELECT
rRETURN
eEXIT
Setting the Touch Key Sound On / Off
To setup, follow steps 1 through 3 above.
. Press the ▲▼ buttons to select Touch Key Sound, then press
the OK or ► button.
HDD & DVD RECORDER
System
HDD
. Press the ▲▼ buttons to select On or Off, then press the OK or
► button.
Library
Guide
Channel
. Press the MENU button to exit the setup menu.
Timer Record
Disc Manager
Auto Power Off
: Off ►
Power Save
: Off
►
Anynet+ (HDMI CEC) : Off
►
DVB-T Auto Subtitle : On
Touch Key Sound
: On
Off
►
✔►
DivX(R) Registration On
►
Setup
42_ system setup
m MOVE
sSELECT
rRETURN
eEXIT
DivX(R) Registration
Please use the Registration code to register this HDD & DVD
Recorder with the DivX(R) Video On Demand format. For more
information, visit www.divx.com/vod
HDD & DVD RECORDER
System
HDD
Library
Auto Power Off
: Off ►
Video On
Demand
Save
: Off
GuideDivX(R)Power
Anynet+ (HDMI CEC) : Off
Channel
Your registration code is XXXXXXXX
DVB-T
Auto
Subtitle
: On
To learn more visit www.divx.com/vod
Timer Record
Touch Key Sound
: On
OK
DivX(R) Registration
Disc Manager
►
►
►
►
►
Setup
sSELECT
rRETURN
eEXIT
● system setup
Setting up the Language Options
If you set the language options, in advance, they will come up automatically every time you watch a movie.
1. With the unit in Stop mode, press the MENU button.
. Press the $% buttons to select Setup, then press the OK or +
button.
. Press the $% buttons to select Language, then press the OK or
+ button.
Language setup menu will be displayed.
HDD & DVD RECORDER
Language
HDD
Library
Guide
Channel
Timer Record
Disc Manager
DVD Audio
: Original ►
DVB-T Audio
: Français
►
DVD Subtitle
: Automatic
►
DVB-T Subtitle
: Français
►
Disc Menu
: English
►
Menu
: English
►
Setup
. Press the $% buttons to select the desired language option,
m MOVE
sSELECT
rRETURN
press the OK or + button.
~ DVD Audio : For the disc audio language.
~ DVB-T Audio : For the current broadcasting Programme provides audio.
~ DVD Subtitle : For the disc subtitles.
~ DVB-T Subtitle : For the current broadcasting Programme provides subtitles.
~ Disc Menu : For the disc menu contained on the disc
~ Menu : For the on-screen menu of your HDD & DVD Recorder.
- Automatic : Sets the HDD&DVD recorder’s menu language to the TV menu language.
- How to use Automatic?
eEXIT
1. The TV that you want to connect to should support the Anynet+ feature.
2. Use the HDMI cable to connect the HDD&DVD recorder to the TV. (See pages 31~32)
3. If the Anynet+ feature of the HDD & DVD recorder is set to “On” (see page 41) and the menu
language is set to “Automatic”, then the menu language will be set to the same as that of the TV.
4. If the TV menu language in Automatic mode is not supported by the recorder, the recorder’s
menu language will be set to the default.
. Press the $% buttons to select the desired language, then press the OK or + button.
M
` If the selected language is not recorded on the disc, the original pre-recorded language is selected.
` The selected language will only appear if it is supported on the disc and DVB-T.
` During the playback, press the SUBTITLE button to select DVD subtitle. Because the default of DVD subtitle is off,
press the $% button to select the desired subtitle.
English _43
system setup
Setting up the Audio Options
You can connect the HDD & DVD Recorder to an external amp or Home theatre.
Allows you to setup the Audio device and sound status depending on the audio system in use.
You can also set NICAM mode.
1. With the unit in Stop mode, press the MENU button.
HDD & DVD RECORDER
. Press the $% buttons to select Setup, then press the OK or +
button.
. Press the $% buttons to select Audio, then press the OK or +
button.
Library
System ►
Guide
Clock Set
►
Language
►
Channel
Timer Record
. Press the $% buttons to select the desired audio option, then
press the OK or + button.
. Press the $% buttons to select the desired item, then press the
OK or + button.
Setup
HDD
Disc Manager
Setup
m MOVE
Audio
►
Video
Parental Lock
►
1
►
Recording
sSELECT
►
rRETURN
eEXIT
Digital Output
~ PCM : Select this when your equipment is not decode Dolby Digital (or MPEG-2) compatible.
~ Bitstream : Outputs Dolby Digital (or MPEG-2) audio as bitstream. Select this when your AV receiver or AV amplifier has a Dolby Digital (or MPEG-2) Decoder.
HDD & DVD RECORDER
Audio
HDD
Library
Guide
Channel
Timer Record
Digital Output
: PCM PCM
DTS
Bitstream
: Off
✔►
►
DRC
: On
►
NICAM
: On
►
Disc Manager
Setup
M
m MOVE
sSELECT
rRETURN
eEXIT
` Digital output setting is equally applied to both Dolby Digital and
MPEG-2 audio. LPCM sound track is always outputted as PCM. It has no relation with Digital Output setting.
` Be sure to select the correct Digital Output or you will hear no sound or a loud noise.
DTS
~ Off : Doesn’t output DTS signal. Select this when your AV receiver (or AV amplifier) does not have DTS decoder.
~ On : Outputs DTS Bitstream via digital output when you play DTS track. Select this only when your AV receiver (or AV amplifier) have DTS decoder.
HDD & DVD RECORDER
Audio
HDD
Library
Guide
Channel
Timer Record
Digital Output
: PCM ►
DTS
: Off
Off
✔►
DRC
On
: On
►
: On
►
NICAM
Disc Manager
M
` When DTS soundtrack is played, sound does not output from
AV Audio Output.
Setup
m MOVE
sSELECT
rRETURN
eEXIT
DRC
This is only active when a Dolby Digital signal is detected.
~ On : When Movie soundtracks are played at low volume or
from smaller speakers, the system can apply appropriate
compression to make low-level content more intelligible and
prevent dramatic passages from getting too loud.
~ Off : You can enjoy the movie with the standard Dynamic Range.
HDD & DVD RECORDER
Audio
HDD
Library
Guide
Channel
Timer Record
Digital Output
: PCM DTS
: Off
DRC
: On
Off
NICAM
On
: On
►
►
►
✔►
Disc Manager
Setup
44_ system setup
m MOVE
sSELECT
rRETURN
eEXIT
NICAM
HDD & DVD RECORDER
Audio
HDD
Library
Guide
Channel
Timer Record
Digital Output
: PCM ►
DTS
: Off
►
DRC
: On
►
Off
: On
On
NICAM
►
✔
Disc Manager
Setup
m MOVE
sSELECT
rRETURN
eEXIT
● system setup
NICAM programmes are divided into 3 types. NICAM Stereo, NICAM
Mono and Bilingual (transmission in another language). NICAM
programmes are always accompanied by a standard mono sound
broadcast and you can select the desired sound by setting NICAM
on or off.
~ On : NICAM mode
~ Off : Only set at this position to record the standard mono sound during a NICAM broadcast if the stereo sound is distorted due to inferior reception conditions.
Setting up the Video Options
This function allows you to setup the video setting.
This function depends on disc type. It may not work for some disc types.
1. With the unit in Stop mode, press the MENU button.
HDD & DVD RECORDER
. Press the $% buttons to select Setup, then press the OK or +
button.
. Press the $% buttons to select Video, then press the OK or +
button.
Video setup menu will be displayed.
. Press the $% buttons to select the desired video option, then
press the OK or + button.
Setup
HDD
Library
System ►
Guide
Clock Set
►
Language
►
Channel
Timer Record
Disc Manager
Setup
m MOVE
Audio
►
Video
►
Parental Lock
1
►
Recording
sSELECT
►
rRETURN
eEXIT
. Press the $% buttons to select the desired item, then press the OK or + button.
TV Aspect
You may want to adjust the screen setting Depending on the type of
television you have. (aspect ratio)
~ 4:3 Letter Box : Select when you want to see the total 16:9 ratio
screen DVD supplies, even though you have a TV
with a 4:3 ratio screen. Black bars will appear at
the top and bottom of the screen.
HDD & DVD RECORDER
Video
HDD
Library
Guide
Channel
Timer Record
Disc Manager
TV Aspect
: 4:3
Letter
Box
4:3
Letter
Box
Pan-Scan
3D Noise Reduction 4:3
: Off
16:9
Wide
Video Output
: Component
►
►
✔►
Component output
: Interlace
►
BD Wise
: Off
►
HDMI Resolution
: 576p
►
Setup
m MOVE
sSELECT
rRETURN
eEXIT
~ 4:3 Pan-Scan : Select this for conventional size TV when you want to see the central portion of the 16:9
screen. (Extreme left and right side of movie picture will be cut off.)
~ 16:9 Wide : You can view the full 16:9 picture on your wide screen TV.
3D Noise Reduction (motion adaptive noise reduction)
~ Off : Normal
~ On : Provides a clear picture through noise reduction (for
recording).
HDD & DVD RECORDER
Video
HDD
Library
Guide
Channel
Timer Record
Disc Manager
TV Aspect
: 4:3 Letter Box
3D Noise Reduction Off
: Off
►
✔►
On
: Component
Video Output
►
Component output
: Interlace
►
BD Wise
: Off
►
HDMI Resolution
: 576p
►
Setup
m MOVE
sSELECT
rRETURN
eEXIT
English _45
system setup
Video Output
You can enjoy high quality image through RGB or Component video
connections. RGB video output is available connecting scart jack
(AV1) and component video output is available connecting
component (Y, PB, PR) jack. Only one of these signals can be
selected at one time.
~ Component
~ RGB
HDD & DVD RECORDER
Video
HDD
Library
Guide
Channel
Timer Record
Disc Manager
Setup
m MOVE
TV Aspect
: 4:3 Letter Box
3D Noise Reduction
: Off
Video Output
►
►
: Component
Component
✔►
Component output RGB
: Interlace
►
BD Wise
: Off
►
HDMI Resolution
: 576p
►
sSELECT
rRETURN
eEXIT
In Component mode, you can set video output to Progressive or Interlace, see page 46.
When the HDMI cable (not supplied) is not connected, available video output jacks are as follow.
Available Video Output Jack
Setting mode
Component mode
RGB Mode
O
X
R, G, B
X
O
Composite
O
X
O
O
Output jack
Component Output (Y, PB, PR)
AV1 Scart
Composite Video out
M
` When the HDMI cable(not supplied) is connected, RGB output does not operate. Video output is set to Component.
Component Output (progressive scan)
This function is available when video output is component. This setting enables you to select a desired
progressive mode. To view ‘Progressive scan mode’, first connect the component cable. (See page 27) Be sure
the Component cables are connected properly.
~ Progressive
HDD & DVD RECORDER
The message "Do you want to maintain progressive mode?
Reverting in 10 seconds." will be displayed.
Select "Yes" to revert progressive mode.
Library
Guide
Channel
~ Interlace
The message "Do you want to maintain interlace mode?
Reverting in 10 seconds." will be displayed.
Select "Yes" to revert interlace mode.
M
Timer Record
Disc Manager
TV Aspect
: 4:3 Letter Box
►
3D Noise Reduction
: Off
►
Video Output
: Component
►
Component output Interlace
: Interlace
✔►
Progressive
: On
►
BD Wise HDMI Resolution
: 576p
►
Setup
m MOVE
` When the HDMI cable (not supplied) is connected, this screen is not displayed.
46_ system setup
Video
HDD
sSELECT
rRETURN
eEXIT
BD Wise (Only Samsung products)
BD Wise is Samsung’s latest inter-connectivity feature.
When you connect Samsung products with BD-Wise to each other via HDMI, the optimum resolution will be
set automatically.
~ On : The original resolution of the DVD disc will be output to the
TV directly.
~ Off : The output resolution will be fixed according to the Resolution
previously set, regardless of the resolution of the disc.
HDD & DVD RECORDER
Video
HDD
Library
Guide
Timer Record
Disc Manager
: 4:3 Letter Box
►
3D Noise Reduction
: Off
►
Video Output
: Component
►
Component output
: Interlace
►
BD Wise
: Off
Off
✔►
HDMI Resolution
On
: 576p
►
Setup
M
m MOVE
sSELECT
`
`
`
If you want to change the resolution in BD Wise, you must set BD Wise to Off in advance.
`
For a proper operation of BD Wise, set each BD Wise menu of the player and the TV to On respectively.
rRETURN
eEXIT
If you set off the BD Wise, the resolution of the connected TV will be adjusted to its maximum resolution automatically.
If the HDD & DVD Recorder is connected to a device that does not support BD Wise, you can not use BD Wise function.
HDMI Resolution
This setting is used when the unit is connected by HDMI with Display devices (TV, projector, etc).
~ BD Wise : Automatically selects the optimal resolution according
to the TV that supports BD Wise. (The BD Wise menu
item appears only if BD Wise is set to On.)
~ 576p 720 x 576
~ 720p : 1280 x 720
~ 1080i : 1920 x 1080
~ 1080p : 1920 x 1080
HDD & DVD RECORDER
Video
HDD
Library
Guide
TV Aspect
: 4:3 Letter Box
3D Noise Reduction
: Off
Video Output
Timer Record
Disc Manager
HDMI Resolution
Setup
►
: Component
BD
Wise
Component output 576p
: Interlace
720p
BD Wise
: Off
Channel
m MOVE
sSELECT
►
✔►
1080i
: 576p
1080p
rRETURN
►
►
►
eEXIT
Output selection
~ Connect the HDD & DVD Recorder to your TV via HDMI.
Set your TV’s input to HDMI.
M
`
The BD Wise menu item appears only if BD Wise is set to On.
BD wise function is enabled only if BD Wise-compliant Samsung Products are connected with each other using the HDMI cable.
` Progressive scan automatically activates when HDMI is connected.
` Consult your TV User’s Manual to find out if your TV supports Progressive Scan. If Progressive Scan is supported,
follow the TV User’s Manual regarding Progressive Scan settings in the TV’s menu system.
` If Video Output is set incorrectly, the screen may be blocked.
` The resolutions available for HDMI output depend on the connected TV or projector. For details, see the user’s
manual of your TV or projector.
` When the resolution is changed it may take a few seconds for a normal image to appear.
English _47
● system setup
Channel
TV Aspect
system setup
Setting up the Parental Lock
The Parental Lock function works in conjunction with DVDs and DVB-T that have been assigned a rating which
helps you control the types of DVDs that your family watches. There are up to 8 rating levels on a disc.
Z
1. With the unit in Stop mode, press the MENU button.
HDD & DVD RECORDER
. Press the $% buttons to select Setup, then press the OK or +
button.
Setup
HDD
. Press the $% buttons to select Parental Lock, then press the
OK or + button.
When you operate your HDD & DVD Recorder for the first time,
the “Create the Password” message will be displayed.
Library
System ►
Guide
Clock Set
►
Language
►
Audio
►
Channel
Timer Record
Disc Manager
Setup
Video
►
Parental Lock
1
►
Recording
m MOVE
sSELECT
. Enter the 4-digit password using the number buttons on the
remote control.
The “Confirm the password” message will be displayed. Enter your password again.
►
rRETURN
eEXIT
If you forgot your password
1. Switch the DVD mode and remove the disc.
. Press and hold the Play/Pause (
) button on the front panel for 10 seconds or more.
Setting the Programme Grade
1. Press the $% buttons to select Programme Grade, then press
the OK or + button.
HDD & DVD RECORDER
Parental Lock
HDD
Library
. Press the $% buttons to select the programme grade you
want, then press the OK or + button.
For example, if you select up to 15, DVB-T that contain 16, 17,
18 will not display. A larger number indicates that the
programme is intended for adult use only.
Guide
Channel
Timer Record
Disc Manager
Programme Grade Off
DVD Level
18: Level1-Kids
Change Password 17
16
15
14
13
12
✔►
►
►
Setup
m MOVE
sSELECT
rRETURN
eEXIT
Setting the DVD Level
1. Press the $% buttons to select DVD Level, then press the OK
or + button.
. Press the $% buttons to select the DVD Level you want, then
press the OK or + button.
For example, if you select up to 6, discs that contain 7, 8 will not
play.
A larger number indicates that the programme is intended for
adult use only.
HDD & DVD RECORDER
Parental Lock
HDD
Library
Guide
Channel
Timer Record
Disc Manager
Setup
m MOVE
Programme Grade
: Off
►
DVD Level
: Level1-Kids
Level8-Adults
Change Password Level7
Level6
Level5
Level4
Level3
Level2
Level1-Kids
sSELECT
rRETURN
►
►
✔
eEXIT
Changing the Password
1. Press the $% buttons to select Change Password, then press
the OK or + button.
HDD & DVD RECORDER
Library
. Enter the 4-digit password using the number buttons on the
remote control. The “Confirm the password” message will be
displayed.
Guide
Channel
Programme Grade
: Off
DVD Level
: Level1-Kids
►
Change Password Disc Manager
Setup
m MOVE
sSELECT
rRETURN
►
►
Timer Record
. Enter your password again using the number buttons on the
remote control.
48_ system setup
Parental Lock
HDD
eEXIT
Setting up the Recording Options
Automatic Chapter Creator
CVKL
(V-mode)
A DVD-Video consists of ‘Titles’ and ‘Chapters’. When you record one programme, it makes one Title.
If you use this function, the Title will be divided into Chapters.
HDD & DVD RECORDER
. Press the $% buttons to select Setup, then press the OK or +
button.
Recording
HDD
Library
Guide
. Press the $% buttons to select Recording, then press the OK
or + button.
Channel
Timer Record
. Press the $% buttons to select Chapter Creator, then press
the OK or + button.
Chapter Creator
: On
Off
EP Mode Time
On
: 6 Hours
EZ Record
►
✔►
: Off
►
V-Mode Compatibility : Off
►
Disc Manager
Setup
m MOVE
. Press the $% buttons to select Off or On, then press the OK or
+ button.
~ Off : Select if you do not want use Automatic Chapter Creator.
~ On : Select this option to use the Automatic Chapter Creator feature.
Press the EXIT button to exit the menu.
sSELECT
rRETURN
eEXIT
. Press the REC button to start recording.
(See pages 73~74 about how to set recording speed)
The message “Do you want to create the chapter menu after this recording?” is displayed.
. Press the _ + buttons to select OK, then press the OK button.
~ A new chapter is created according to the selected recording mode. A chapter will be about 5 minutes
long in XP and SP, and about 15 minutes long in LP and EP mode.
. Press the STOP button to stop recording.
. To display the created titles, finalise the disc (See page 104) and then press the TITLE MENU button. The
title menu will be displayed.
~ Finalising is generally unnecessary when using a DVD+RW disc.
10.To display the created chapters, select the desired Title and then press the DISC MENU button. The
chapter menu for the selected Title will be displayed.
J
` The Automatic Chapter Creator function does not work during Timer Recording or when you turn the power off.
EP Mode Time Setting
You can select one of four recording modes by pressing the REC
MODE button repeatedly.
In EP(Extended Play) mode, you can set recording time to 6 or 8
hours with this setting.
HDD & DVD RECORDER
Recording
HDD
Library
Guide
Channel
~ 6 Hours
~ 8 Hours
Timer Record
Chapter Creator
EP Mode Time
EZ Record
: On
6 Hours
6:Hours
Off
8:Hours
►
✔►
►
V-Mode Compatibility : Off
►
Disc Manager
Setup
m MOVE
sSELECT
rRETURN
eEXIT
English _49
● system setup
1. With the unit in Stop mode, press the MENU button.
system setup
EZ Record
CVKL
(V-mode)
This function allows you initialise and Finalise a disc automatically.
1. Press the ▲▼ buttons to select EZ Record, then press the OK
or + button.
HDD & DVD RECORDER
Library
. Press the ▲▼ buttons to select On, then press the OK or +
button.
Press the EXIT button to exit the menu.
. Insert a disc.
If the disc is new, It is initialised to V mode automatically.
(DVD-RW only)
Recording
HDD
Guide
Channel
Timer Record
Chapter Creator
EP Mode Time
EZ Record
: On
►
: 6 Hours
►
: Off
Off
✔►
V-Mode CompatibilityOn
: Off
►
Disc Manager
Setup
m MOVE
sSELECT
rRETURN
eEXIT
. Press the REC button.
. EZ Record function will automatically Finalise the disc under the following conditions.
~ When you press the OPEN/CLOSE button on your HDD & DVD Recorder after recording on at least
70% of the disc.
The tray will open after the disc has been finalised.
~ The above feature is available only when a DVD-RW(V), DVD+R or DVD-R disc is inserted.
M
` If you insert a new DVD-RW disc, It is initialised to V mode automatically.
` If you insert a new DVD+RW disc, it will be formatted automatically.
` If you select off, you must initialise (see page 72) and finalise the disc manually in the Disc Manager menu. (see
page 104)
` The length of Recording is different according to recording mode. (see pages 73~74)
V-Mode Compatibility
This feature is about the setup for selecting audios when recording
the Dual STEREO (Multi-audio) broadcasting on HDD. It does not
affect to the direct DVD recording of a programme.
~ Off : Both “Dual L” and “Dual R” of the multi-audio broadcasting
are recorded on HDD. Titles recorded on HDD under such
setup status cannot be copied to DVD+RW/±R or DVD-RW
(V mode).
~ On : Either “Dual L” or “Dual R” of the multi-audio broadcasting is
recorded on HDD. Titles recorded on HDD under such setup
status can be copied to DVD+RW/±R or DVD-RW (V mode)
“Dual L” and “Dual R” options can be selected from “Audio
Selection.”
HDD & DVD RECORDER
Recording
HDD
Library
Guide
Channel
Timer Record
Chapter Creator
: On
►
EP Mode Time
: 6 Hours
►
EZ Record
: Off
V-Mode CompatibilityOff
: Off
►
✔►
On
Disc Manager
Setup
m MOVE
sSELECT
rRETURN
HDD & DVD RECORDER
eEXIT
Recording
HDD
Library
Guide
Channel
Timer Record
Chapter Creator
: On
►
EP Mode Time
: 6 Hours
►
EZ Record
: Off
►
V-Mode Compatibility : On
Audio Selection
: OffL
Dual
►
✔►
Dual R
Disc Manager
Setup
50_ system setup
m MOVE
sSELECT
rRETURN
eEXIT
DTV functions
‘EPG’ is used as the same meaning with ‘TNT’.
Basic Functions
After the television channels have been stored, you will see the following picture(banner) each time you switch
channels.
Banner Elements
Displays the favorite channel.
HDD
DTV
001
TF1
Displays the teletext.
Displays the subtitle.
Displays the multi audio.
M
` The icon is displayed according to the service information of signal.
` The icon is displayed only with more than one audio type and language.
` By pressing the button, you can see the detailed information.
Select Audio Track
1. Press the AUDIO button to see the Audio Track list.
. Press the $% buttons to select desired Audio Track, then press
the OK button.
Audio Track FRA MPEG
>Change
Setting the Favorite List(Digital)
You can immediately register the present channel to the Digital
Favorite Channel List.
Favorite List(Digital)
1. Press the FAV LIST button while you are viewing a programme.
001 TF1
002 NRJ12
. To add the current channel to the Digital Favorite channels, press
the GREEN(B) button.
To delete a favorite channel from the Digital Favorite channel list,
press the RED(A) button.
[/] Page
Remove
Add Current
r Return
– To watch the Favorite List(Digital) –
Press the FAV LIST button and then select the channel.
Press the OK button to watch that channel.
English _51
● DTV Functions
Display Screen
DTV functions
Changing the Subtitle Language
When the current broadcasting programme provides subtitle, press
the SUBTITLE button . If Subtitle is available on current programme,
menu bar is displayed on the upper side.
Subtitle OFF
1. Press the SUBTITLE button.
. Press the ▲▼ buttons to select a desired subtitle, then press the
OK button.
>Change
Setting the Teletext OSD
When the current broadcasting programme provides teletext, press
the TEXT button to see the teletext. If teletext is available on current
programme, menu bar is displayed on the upper side.
Teletext FRA(Transparency:off)
1. Press the TEXT button.
. Press the ▲▼ buttons to select a desired Teletext.
. Press the ◄ ► button to select TRANSPARENCY, then press
the OK button.
>Change <TRANSPARENCY
P100
TF1
30 . 01
TFI
15 : 08 : 09
SOUS-TITRAGE
PROGRAMMES SOUSTITRES
BON PLAN
DIALOGUEZ PAR SMS EN DIRECT SUR
NOTRE CHAT
J o u e z
e n
a p p e l a n t
METEO
102
3 2 8 0
e t
g a g n e z
INFOS
200
s é j o u r
a u
s k 1
p o u
SPORTS
250
ASTRO
270
FOOT
300
Gagnez jusqu'à
CINE
1000
euros
190
PETITES
ANNONCES
OFFRES D'EMPLOI 400
888
145
199
r
l e
u n
4
219
510
RESUL TATS ET RAPPORTS PMU
FINI LA SOLITUDE !
LA NEIGE ARRIVE ?
EXCLUSIF : RENCONTRES PAR SMS
217
290
216
213
PACK MICRO POUR 38 EUROS/MOIS
256
Guide
The electronic programme guide gives you a channel list for the channels.
1. With the unit in Stop mode, press the MENU button.
. Press the ▲▼ buttons to select Guide, then press the OK or ►
button.
~ Press the GUIDE button while you are viewing a programme.
(DTV)
~ RED(A) button (Timer Record) : Setting the Timer Record.
~ (]) button : Go to next day
~ ([) button : Go to previous day
 It displays programme from now to 7 days after.
~ ▲▼◄ ► button : select the programme and station.
~ INFO button (Information) : View the detail information
M
DTV Guide
12:00 TUE 1 JAN 2009
12:00 - 12:25 Blue Peter
TUE 1 JAN
001
BBC ONE
002
BBC TWO
007
BBC THREE
030
CBBC Channel
040
BBC NEWS 24
001
BBCi
A
◄
12:30
---
The Weakest Link
Basli Brush
Neighbours
---
Tracy
Beake
13:30
►
BBC News
Look North
Beg. Borrow or Steal
Strictly Come Dancing: It T
Blue Peter
BBC News
Out There
BBC News
BBCi
BBCi
Timer Rec
[/] Previous/Next Day
` The contents of cell could be displayed with a delay according to the broadcasting.
` If 'Daylight Saving Time' and 'GMT Time' settings are wrong, EPG Time will be incorrect.
52_ DTV functions
13:00
Blue Peter
---
INFO
INFORMATION
---
Guide Timer Recording
Make sure that clock must be set before operating this function. (see
pages 37~38)
1. Press the ▲▼◄ ► buttons to select desired programme, then
press RED(A) button.
. The time of Guide is the time of the current channel enters.
. You can check the setting in the scheduled List. (see pages
81~83)
` The title information is displayed in the Title List as for Guide REC.
` If Timer Rec is set, the icon is displayed in the set programme.
` Up to 12 recording are possible including guide recording and general
recording.
DTV Guide
12:00 - 12:25 Blue Peter
TUE 1 JAN
001
BBC ONE
002
BBC TWO
007
BBC THREE
030
CBBC Channel
040
BBC NEWS 24
001
BBCi
A
◄
12:30
13:00
Blue Peter
---
---
The Weakest Link
Basli Brush
Neighbours
---
13:30
►
BBC News
Look North
Beg. Borrow or Steal
Strictly Come Dancing: It T
Tracy
Beake
Blue Peter
BBC News
Out There
BBC News
BBCi
---
BBCi
Timer Rec
[/] Previous/Next Day
INFO
INFORMATION
DTV Guide
12:00 TUE 1 JAN 2009
12:00 - 12:25 Blue Peter
Timer
TUE 1 JAN
◄ Rec
001
BBC ONE
002
BBC TWO
007
BBC THREE
030
CBBC Channel
040
BBC NEWS 24
001
BBCi
A
Blue Peter
---
12:30
13:00
---
Neighbours
13:30
BBC News
HDD
Basli Brush
---
Tracy
Beake
Strictly Come Dancing: It T
Blue Peter
DVD
BBC News
►
Look North
Select
media
Rec.
The Weakest
Link for TimerBeg.
Borrow or Steal
Out There
BBC News
BBCi
---
BBCi
Timer Rec
[/] Previous/Next Day
INFO
INFORMATION
English _53
● DTV Functions
M
12:00 TUE 1 JAN 2009
playback
This section introduces basic functions of playback and playback by disc type.
Read the following information before playing a disc.
Region code (DVD-Video only)
Both the HDD & DVD Recorder and the discs are coded by region. These regional codes must match in
order for the disc to play. If the codes do not match, the disc will not play. The Region Number for this HDD
& DVD Recorder is described on the rear panel of the HDD & DVD Recorder.
Logos of Discs that can be played
Dolby Digital
Stereo
DTS
PAL broadcast system in U.K,
France, Germany, etc.
Digital Audio
DivX
MP3
Disc Shape
Max. Playing Time
Single sided(12cm)
Double sided(12cm)
Single sided(8cm)
Double sided(8cm)
Single sided(12cm)
Single sided(8cm)
Single sided(12cm)
Single sided(8cm)
Single sided(12cm)
Single sided(8cm)
Single sided(12cm)
Single sided(8cm)
240 min.
480 min.
80 min.
160 min.
74 min.
20 min.
1 hr. (XP: Excellent Quality)
2 hrs. (SP: Standard Quality)
4 hrs. (LP: Long Playback)
6 or 8 hrs. (EP:Extended)
2 hr. (XP: Excellent Quality)
4 hrs. (SP: Standard Quality)
8 hrs. (LP: Long Playback)
12 or 16 hrs. (EP:Extended)
4
Disc types that can be played
Disc Types
DVD-VIDEO
Disc Logo
content
Recorded
content
AUDIO
VIDEO
AUDIO-CD
AUDIO
JPEG
JPEG Image
MP3
MP3 Audio
DivX
DivX Movie
Single sided(12cm)
DVD-RAM
AUDIO
VIDEO
(4.7GB)
Double sided(12cm)
(9.4GB)
54_ playback
Disc Types
Disc Logo
content
Recorded
content
AUDIO
DVD-RW
VIDEO
Disc Shape
12cm (4.7GB)
AUDIO
DVD-R
VIDEO
Dual Layer(12cm)
(8.5GB)
AUDIO
DVD+RW
VIDEO
12cm (4.7GB)
Single Layer(12cm)
(4.7GB)
AUDIO
DVD+R
DVD+R DVD+ReWritable
VIDEO
Dual Layer(12cm)
(8.5GB)
1 hr (XP: Excellent Quality)
2 hrs (SP: Standard Quality)
4 hrs (LP: Long Playback)
6 or 8 hrs (EP:Extended)
1 hr (XP: Excellent Quality)
2 hrs (SP: Standard Quality)
4 hrs (LP: Long Playback)
6 or 8 hrs (EP:Extended)
1 hr. 50min (XP : Excellent Quality)
3 hrs. 40min (SP : Standard Quality)
7 hrs. 20min (LP : Long Playback)
11 or 14 hrs. 40min (EP : Extended)
1 hr (XP: Excellent Quality)
2 hrs (SP: Standard Quality)
4 hrs (LP: Long Playback)
6 or 8 hrs (EP:Extended)
1 hr (XP: Excellent Quality)
2 hrs (SP: Standard Quality)
4 hrs (LP: Long Playback)
6 or 8 hrs (EP:Extended)
1 hr. 50min (XP : Excellent Quality)
3 hrs. 40min (SP : Standard Quality)
7 hrs. 20min (LP : Long Playback)
11 or 14 hrs. 40min (EP : Extended)
JPEG
CD-R/-RW
DVD-RAM/-RW/-R
DVD+R DVD+ReWritable
MP3
–
–
DivX
Discs that cannot be played
DVD-Video with a region number other than “2” or “ALL”
3.9 GB DVD-R Disc for Authoring.
DVD-RAM/-RW(VR mode) not recorded following the Video Recording Standard
A DVD±R/DVD-RW(V) disc which has been recorded and not finalised in a different manufacturer’s
recorder.
~ DVD-ROM/PD/MV-Disc, etc
~ VCD/SVCD/CVD/CD-ROM/CDV/CD-G/CD-I
~ BD, HD-DVD
~
~
~
~
M
` This HDD & DVD Recorder can only operate with discs that are compatible with DVD-RAM Standard Version 2.0.
` Playback and/or recording may not work for some types of discs, or when specific operations, such as angle change
and aspect ratio adjustment, are being performed. Information about the discs is written in detail on the box. Please
refer to this if necessary.
` Do not allow the disc to become dirty or scratched, finger prints, dirt, dust, scratches or deposits of cigarette smoke
on the recording surface may make it impossible to use the disc for recording.
` DVD-RAM/±RW/±R discs may not be able to play on some DVD players, depending on the player, disc and the
condition of the recording.
` Discs with NTSC programmes recorded on them can be played but cannot be recorded using this product.
English _55
● Playback
Single Layer(12cm)
(4.7GB)
Max. Playing Time
playback
Playing a Disc
1. Press the OPEN/CLOSE button.
. Place a disc gently into the tray with the disc’s label facing up.
. Press the OPEN/CLOSE button to close the disc tray.
~ The HDD & DVD Recorder does not play discs automatically after being powered on initially.
~ When the HDD & DVD Recorder is powered on and a disc is in the tray, the unit will be activated and
wait in stop status.
~ Press the PLAY( ) button to start playback.
. Press the STOP(
) button to stop playback.
M
` When you stop playing back a disc, the HDD & DVD Recorder remembers where you stopped, so when you press
J
`
`
`
`
`
PLAY( ) button again, it will pick up where you left off. (Unless the disc is removed or the HDD & DVD Recorder is
unplugged, or if you press the STOP( ) button twice.)
Do not move your HDD & DVD Recorder while playing, as this may cause damage to the disc.
Make sure to press the OPEN/CLOSE button to open or close the disc tray.
Do not push the disc tray while it is being opened or closed, as this may cause a product malfunction.
Do not place foreign materials on or in the disc tray.
Some functions may perform differently or be disabled depending on the disc type.
If this occurs, refer to the instructions written on the disc case.
` Be especially careful that children’s fingers are not caught between the disc tray and the tray chassis when it closes.
` You must only insert one DVD disc at a time. Inserting two or more discs will not allow playback and may cause
damage to the HDD & DVD Recorder.
Using the Disc Menu & Title Menu
Some type of discs contain a dedicated menu system that allows you to select special functions for title, chapter,
audio track, subtitle, film preview, information on characters, etc.
For DVD-VIDEO Disc
~ Disc Menu : Press the DISC MENU button to enter the disc menu of the disc.
~ Move to the setup menu related to playback operation.
~ You can select audio language and subtitle etc. provided by the disc.
Z
~ Title Menu : Press the TITLE MENU button to move to the title menu of the disc.
~ Some discs may not support the title menu functionality.
For HDD/DVD-RAM/±RW/±R Disc
SXCVKL
~ Title List
Press the TITLE LIST button. Title List is a list of previously recorded programmes. If a title is deleted, that
title cannot be played again.
~ Play List (HDD/DVD-RAM/-RW(VR))
Press the PLAY LIST button. This refers to a list of user-selected titles. When one playlist is played, only
the scene selected by the user will play and then stop. Since only the information necessary for playing
a desired scene is included in a playlist, even if that playlist is deleted, the original recording will not be
deleted. (only VR mode)
56_ playback
Using the Playback Related buttons
Searching through a Chapter or Track
SZXCV
During play, press the SEARCH (
KL
) buttons on the remote control.
)X2)X4)X8
DVD-RAM/±RW/±R
● Playback
HDD/DVD-VIDEO/
) X 16  ) X 32  ) X 128
DivX
)X2)X4)X8
AUDIO CD (CD-DA)
)X2)X4)X8
~ You can scan the programme in reverse.
) buttons, playback is done at the default speed of X 4.
~ When you press and hold the SEARCH (
If you release the SEARCH (
) buttons , playback is performed at a normal speed.
~ To return to normal speed playback, press the PLAY ( ) button.
M
` You can hear sound during forward search(X 2) in HDD/DVD-VIDEO/DVD-RAM/±RW/±R disc.
(No sound is heard during Scan(Search) mode in DivX disc.)
` The speed marked in this function may be different from the actual playback speed.
Skipping Chapters, Titles or Markers
SXCV
During play, press the SKIP (
KL
) buttons on the remote control.
~ If you press the SKIP ( ) button,
It moves to the beginning of the chapter or title or marker. Pressing the button once again within 3 seconds
returns to the beginning of the previous chapter or title or marker
~ If you press the SKIP ( ) button,
It moves to the next chapter or track or marker
Slow Motion Play
SZXCVKLD
In pause mode, press the SEARCH (
) buttons on the remote control.
~ If you press the SEARCH ( ) button,
* 1/2  * 1/4  * 1/8
~ If you press the SEARCH ( ) button,
& 1/2  & 1/4  & 1/8
~ To return to normal speed playback, press the PLAY (
) button.
Press and hold the SEARCH (
) buttons during pause, the disc will play slowly at 1/4 speed. If the
button is released, the pause operation will resume.
M
` The speed marked in this function may be different from the actual playback speed.
` Slow motion operates only in the forward direction on DivX discs.
English _57
playback
Step Motion Play
SZXCVKLD
Press the SKIP( , ) buttons on the remote control in the pause mode.
~ Each time the button is pressed, a new frame will appear.
When the SKIP( ) button is pressed, the previous frame will be activated.
When the SKIP( ) button is pressed, the next frame will be activated.
~ To return to normal speed playback, press the PLAY ( ) button.
M
` Step motion operates only in the forward direction on DivX discs.
Using the INFO button
The INFO function allows you to easily search for a desired scene by accessing title, chapter, time.
You can also change the subtitle and audio settings and set some features including Angle, Repeat, Zoom.
Moving to a scene directly using the INFO
SZXCVKLD
If you want to move to a certain title, chapter or time, use this
function.
1. Press the INFO button during playback.
. Press the $% buttons to select Search, then press the OK
button or + button.
DVD-VIDEO
� Search
O Subtitle
Q Audio
� Angle
P Repeat
� Zoom
>MOVE
Info
\
Off
ENG Dolby Digital 5.1 CH
1/1
Off
Off
\
<Change
. Press the $% buttons to select Title, Chapter or Time.
. Press the _ + buttons or number buttons to select the desired
scene, then press the OK button.
In case of searching a time, enter the time in the sequence of hours, minutes, and seconds using the
number buttons. Then press the OK button.
M
` This may not work for some discs.
When an audio CD(CD-DA) or an MP3/JPEG disc is inserted, depending on the disc type, the information display
may not appear.
` The Time Search function does not operate in some discs.
` To make the screen disappear, press the RETURN button.
Selecting the Subtitle Language
ZD
Selects one of the subtitle language recorded on the disc.
You can also operate this function by pressing the SUBTITLE button on the remote control.
1. Press the INFO button during playback.
. Press the $% buttons to select Subtitle.
. Press the _ + buttons to select the desired subtitle language.
M
` The subtitle display may be different depending on the disc type.
` Some discs allow you to select the language for the disc menu only.
58_ playback
Selecting the Soundtracks & Audio Channels
SZXCKLD
Selects one of the soundtracks recorded on the disc. Also selects the audio channels from recorded TV
programmes.
You can also operate this function by pressing the AUDIO button on the remote control.
1. Press the INFO button during playback.
● Playback
. Press the $% buttons to select Audio.
. Press the _ + buttons to select the desired sound tracks or audio channel.
M
` Soundtracks or Audio channel may be different because they are disc-specific.
` Some discs allow you to select the audio language for the disc menu only.
Changing the Camera Angle
Z
When a DVD VIDEO contains multiple angles of a particular scene, you can select the Angle function.
1. Press the INFO button during playback.
. Press the $% buttons to select Angle.
. Press the _ + buttons to select the desired angle.
M
` This function is disc-dependent, and may not work on all DVDs.
` This function does not work when a DVD has not been recorded with a multi-camera angle system.
` Displays the current angle, total angle number.
Repeat Play
Playing Repeatedly (Repeat Playback)
SZXCVKLD
You can also operate this function by pressing the REPEAT button on the remote control.
1. Press the INFO button during playback.
. Press the $% buttons to select the Repeat.
. Press the _ + buttons to select Off, A-B or Title or Chapter you want to play repeatedly, then press the
OK button.
M
` HDD/DVD-RAM/-RW(VR mode), unfinalised DVD±R and unfinalised DVD-RW (V mode) discs will do not repeat a
chapter.
` You can also activate Normal Playback by pressing the EXIT(
) button.
English _59
playback
Repeat A-B
SZXCVKL
1. Press the INFO button during playback.
Repeat
. Press the $% buttons to select Repeat.
A-B >
. Press the _ + buttons to select Repeat A-B, then press the OK
button.
. Press the OK button at the point where you want the repeat play
to start (A) and press it again at the point where you want the
repeat play to stop (B). Repeat playback of the A-B section starts.
M
>CHANGE sSelect
` If you set point (B) before five seconds of playback has lapsed, the prohibition mark ( ) will appear.
` You can also activate Normal Playback by pressing the EXIT(
) button.
` Audio CDs(CD-DA), MP3 discs and DivX discs do not support the Repeat A-B function.
Zooming-In
SZXCVKL
1. Press the INFO button during playback.
. Press the ▲▼ buttons to select Zoom, then press the OK or +
button.
( ) will be displayed.
. Press ▲▼_ + buttons to move to the area you want to enlarge.
. Press the OK button.
The screen will be enlarged to twice the normal size. The screen
size will be enlarged to four times the normal size.
HDD/DVD-VIDEO/DVD-RAM/±RW/±R
M
normal size → X2 → X4 → X2 → normal size
` When the recording is done in EP mode, the zoom function is not supported except when the recording has been in
DVD-VIDEO and finalised DVD-R/-RW(V).
60_ playback
Using Markers
SXC
(VR mode)
Set marks at scenes you want to see again so that you can start playback from the marked position.
Setting Markers
1. Press the MARKER button during playback.
01 02 -- -- -- -- -- -- -- -- N : 2
. Press the + buttons to move to the next position.
. Press the OK button again when the desired scene appears.
~ The number 02 is displayed and the scene is memorised.
~ HDD, DVD-RAM or DVD-RW (VR Mode) discs have the Marker < MOVE
sPLAY
Cancel
rRETURN
function instead of the Bookmark function. Since the scenes may
be displayed as many different pages, numbering is necessary.
If a disc in use is encoded with Disc Protection, Markers cannot be set or deleted, only playback is available.
Playing back a marker
1. Press the MARKER button during playback.
. Press the _ + buttons to select a marked scene.
. Press the OK or PLAY ( ) button to start playing from the selected scene.
~ If you press the SKIP ( ) button, it moves to the beginning of the marker. Pressing the button once
again within 3 seconds returns to the beginning of the previous marker.
~ If you press the SKIP ( ) button, it moves to the next marker.
Clearing a marker
1. Press the MARKER button during playback.
. Press the _ + buttons to select a marked scene.
. Press the RED(A) button to delete the selected mark.
~ When a marker is cleared while HDD/DVD-RAM/-RW (VR mode) is playing, marker numbers will change.
For example, if the 7th marker is cleared after ten markers are registered, the marker numbers after the
eighth will automatically move ahead by one and the 8th marker becomes the 7th.
Using the Bookmarks
ZCVKL
(V mode)
Setting Bookmarks
1. Press the MARKER button during playback.
Bookmark
. Press the OK button when the desired scene appears.
~ The number 1 is displayed and the scene is memorised.
1 2 - - - - - - - --
. Press the + buttons to move to the next position.
. Press the OK button again when the desired scene appears.
The number 2 is displayed and the scene is memorised.
~ Repeat above to bookmark other positions.
~ You can bookmark up to 10 scenes.
M
< MOVE
sPLAY
Cancel
rRETURN
` When the disc tray is opened and then closed, bookmarks will disappear.
English _61
● Playback
Marker
. Press the OK button when the desired scene appears.
~ The number 01 is displayed and the scene is memorised.
playback
Playing back a bookmark
1. Press the MARKER button during playback.
. Press the _ + buttons to select a bookmarked scene.
. Press the OK or PLAY(
) button to start playing from the selected scene.
Clearing a bookmark
1. Press the MARKER button during playback.
. Press the _ + buttons to select a bookmarked scene.
. Press the RED(A) button to delete the selected bookmark.
Playing an Audio CD/MP3
Buttons on the Remote Control used for Audio CD(CD-DA)/MP3 playback
SKIP (
) button : Moves to the previous or next page.
Press the SEARCH (
) buttons : Fast Play
(X 2, X 4, X 8) (Audio CD only)
STOP (
PAUSE (
PLAY (
(song).
) button : Stops a track(song).
) button : Pauses playback.
) button, OK button : Plays the selected track
▲▼ : Selects a track (song).
7
RED(A) button : • Creates a playlist or go to playlist.
• Select All : MP3, CD-DA
• Copy : MP3
• CD Import : Audio CD
8
GREEN(B) button : Selects the sort order. (MP3 disc only)
9
YELLOW(C) button : Selects the play mode. (REPEAT)
10 BLUE(D) button : Selects a contents. (MP3 disc only)
Playing an Audio CD(CD-DA)
1. Insert an audio CD (CD-DA) into the disc tray.
~ The audio CD menu appears and the tracks (songs) are played automatically.
. Press the ▲▼ buttons to select the track (song) you want to hear, and then press the OK button.
62_ playback
Audio CD(CD-DA) Screen Elements
CD
Music List
TRACK01
( @ + # ) 00:02:22
CDDA
TRACK01
1/10
Title
TRACK01
TRACK02
TRACK03
TRACK04
TRACK05
TRACK06
TRACK07
Edit
Length
4:19
3:57
3:57
4:03
4:09
5:08
3:31
Displays the current file type and file name.
Display available buttons.
Play Mode
[/] Previous/Next Page
a Check
● Playback
No.
Q
002
003
004
005
006
007
Current track (song) : Displays the number of the track
currently being played.
Displays available buttons and a playback time
corresponding to a portion that is currently played.
Displays the current play index, total track number.
eExit
Displays the track list (song list).
Playing an MP3 Disc
1. Insert an MP3 disc into the disc tray.
~ The menu is displayed
. Press the ▲▼ buttons to select Library, then press the OK or + button.
. Press the ▲▼ buttons to select Music, then press the OK or + button.
. Press the ▲▼ buttons to select the track you want to hear, and then press the OK button.
MP3 Screen Elements
CD
Music List
SONG01.mp3
1/9
No.
Y
Q
002
003
004
005
006
@ + # 00:02:22
9 SONG01.mp3
E ROOT
Edit
Sort
[/] Previous/Next Page
Title
ROOT
SONG01.MP3
SONG02.MP3
SONG03.MP3
SONG04.MP3
SONG05.MP3
SONG06.MP3
Size
3.8 MB
3.8 MB
5.1 MB
9.2 MB
5.2 MB
10.3 MB
Play Mode
Contents
a Check
eExit
Current track (song) : Displays the name of the track being
played.
Displays available buttons and a playback time
corresponding to a portion that is currently played.
Displays the current file type, file name and folder name.
Displays available buttons.
Displays the current play index, total track number.
Displays the track list (song list).
Repeat CD (CD-DA) & MP3
You can also operate this function by pressing the REPEAT button on the remote control.
During playback, press the REPEAT button repeatedly to select the repeat mode you want.
1. Press the YELLOW(C) button during the Music List playback.
CD
Music List
TRACK01
1/10
. Press the ▲▼ buttons to select desired play mode, then press
No.
Title
Length
the OK or + button.
Q TRACK01
4:19
002 TRACK02
3:57
~ Normal (CD (CD-DA)/MP3) : Tracks on a disc are played in the
003 TRACK03
3:57
( @ + # ) 00:02:22
004 TRACK04
4:03
Normal
order in which they were recorded on the disc.
TRACK01
005 TRACK05
4:09
Repeat Track
006 TRACK06
5:08
Repeat All
~
Repeat Track (CD (CD-DA)/MP3)
007 TRACK07
3:31
Random
Edit
Play Mode
~
Repeat Folder (MP3)
[/] Previous/Next Page
a Check
eExit
~
Repeat All (CD (CD-DA)/MP3)
~
Random (CD (CD-DA)/MP3) : The random option plays a disc’s tracks in random order.
CDDA
English _63
playback
CD Import
1. Press the RED(A) button during the Music List playback.
CD
. Press the ▲▼ buttons to select CD Import, then press the OK or
+ button.
. Press the $% buttons to select file you want to copy, then press
the MARKER button until a checkmark appears.
~ If you don't want to copy a certain one of the checked entries,
simply select that entry and press MARKER button to deselect it
until a checkmark disappears.
. Press the +$% buttons to select the target media, then press the
OK button.
~ You can create a new folder by pressing the GREEN(B) button.
Music List
TRACK01
1/10
( @ + # ) 00:02:22
CD Import
CDDA TRACK01
New
Playlist
Go To Playlist
Select All
M
Length
4:19
3:57
3:57
4:03
4:09
5:08
3:31
Play Mode
a Check
CD
eExit
CD Import
Selected Items:
Available:
Source : DVD
To :
001
002
003
004
005
006
9 CDDA
8 3.64MB
Start Copy TRACK01
TRACK02
TRACK03
TRACK04
TRACK05
TRACK06
Sort [/] Previous/Next Page
` The format of a mp3 file after imported is as follows:
Bitrate 128kbps
Channel 2(stereo)
Sampling Rate 44KHz
Title
TRACK01
TRACK02
TRACK03
TRACK04
TRACK05
TRACK06
TRACK07
Edit
[/] Previous/Next Page
. Press the RED(A) button to select Start Copy. The message
"Number of file : x" is displayed.
. Press the _ + buttons to select Start, then press the OK button.
File copy begins.
~ To cancel the copying in progress, press the EXIT ( ) button.
No.
Q
002
003
004
005
006
007
E HDD
Select All Unselect All
a Check
eExit
CD
CD Import
Selected Items: 9.68MB (2)
Available : 236724MB
Source : DVD
To : HDD
Copying...
;
Y ROOT
; ROOT
Free space
236623 MB
001: TRACK01
Number of file : 1 / 2
002
TRACK02
File Name
: TRACK01.CDA
003 TRACK03
�CDDA
33%
004 TRACK04
�3.84MB
006 TRACK06
` DTS CDDA and copy protected discs can not be imported.
Start Copy Sort Select All Unselect All
eExit
New Playlist
A
You can register a maximum 30 tracks in the playlist.
1. Press the RED(A) button during the Music List playback.
. Press the ▲▼ buttons to select New Playlist, then press the OK
or + button.
. Press the ▲▼ buttons to select tracks in the order in which you
want them to play, then press the OK button.
~ If you playlisted a wrong track, press the +▲▼ buttons to select
the wrong track, then press the OK button.
. To store the Playlist, press the RED(A) button.
A new Playlist will be created.
CD
No.
001
002
003
004
005
006
007
Make Playlist
TRACK01
TRACK02
TRACK03
TRACK04
TRACK05
TRACK06
TRACK07
Title
No.
001
002
003
004
Save
Music List
mMove
sAdd
TRACK10
TRACK08
TRACK04
TRACK07
Playlist
rReturn
eExit
CD
Playlist
�
�
No.
Y
E
Title
PLAYLIST
PLAYLIST01
Length
( @ + # ) 00:00:00
Y PLAYLIST
mMove
64_ playback
sSelect
a Check
eExit
Go To Playlist
A
1. Press the RED(A) button during the Music List playback.
. Press the ▲▼ buttons to select Go To Playlist, then press the
OK or + button.
Playlist
�
�
No.
Y
E
Title
PLAYLIST
PLAYLIST01
Length
( @ + # ) 00:02:22
Y PLAYLIST
mMove
sSelect
a Check
eExit
Delete the Playlist
A
1. Press the RED(A) button during the Music List playback.
. Press the ▲▼ buttons to select Go To Playlist, then press the
OK or + button.
. Press the ▲▼ buttons to select the Playlist you want to delete.
. Press the RED(A) button.
. Press the _ + buttons to select Yes, then press the OK button.
The selected Playlist is deleted.
M
CD
Playiist
� 1/2
�
( @ + # ) 00:00:00
No.
Title
Y Playlist
E Playlist01
Do you want to delete?
E Playlist02
� PLAYLIST01
Delete <Move
Yes
Edit Playlist sSelect
Length
No
New Playlist Music List
rReturn
eExit
` When the player turns off or opens a file /disconnects, any playlists in the disc or USB memory will be deleted.
Go To Edit Playlist
A
1. Press the RED(A) button during the Music List playback.
. Press the ▲▼ buttons to select Go To Playlist, then press the
OK or + button.
. Press the ▲▼ buttons to select the Playlist you want to edit.
. Press the GREEN(B) button in playlist mode.
. Press the ▲▼ buttons to select tracks in the order in which you
want them to play, then press the OK button.
~ If you playlisted a wrong track, press the +▲▼ buttons to
select the wrong track, then press the OK button.
CD
No.
001
002
003
004
005
006
007
Edit Playlist
TRACK01
TRACK02
TRACK03
TRACK04
TRACK05
TRACK06
TRACK07
Title
Save
Music List
mMove
sAdd
No.
001
002
003
004
TRACK10
TRACK04
TRACK06
TRACK07
rReturn
Playlist
eExit
. To store the Playlist, press the RED(A) button.
Playlist will be edited.
English _65
● Playback
. Press the ▲▼ buttons to select the desired playlist folder, then
press the OK button.
The selected tracks are played automatically.
CD
playback
Go To Music List
A
1. Press the BLUE(D) button during the Playlist playback.
The Music List will be displayed.
CD
Playlist
� 1/4
TRACK04
( @ + # ) 00:02:22
CDDA TRACK04
� PLAYLIST01
No.
Y
R
003
004
005
Title
PLAYLIST01
TRACK04
TRACK02
TRACK06
T RACK01
Edit Playlist
New Playlist
Length
4:03
3:57
5:08
4:19
Music List
eExit
Using the Sort
A
When you need to change the Sort order of Music List, you can
change it simply.
CD
Music List
SONG 1.mp3
. Press the ▲▼ buttons to select the desired item, then press the
OK or + button.
~ Name : In alphabetical order
~ Size : In order of audio file size.
M
1/10
No.
1. While the list menu is displayed, press the GREEN(B) button to
select Sort.
Y
Q
002
003
004
005
006
@ + # 00:02:22
9 SONG 1.mp3
E ROOT
Name
Size
Edit
Sort
[/] Previous/Next Page
Title
ROOT
SONG 1.MP3
SONG 2.MP3
SONG 3.MP3
SONG 4.MP3
SONG 5.MP3
SONG 6.MP3
Size
3.8 MB
3.8 MB
5.1 MB
9.2 MB
5.2 MB
10.3 MB
Play Mode
Contents
a Check
eExit
` Audio CD(CD-DA) is not available.
` You can sort by Name, Length. Sorted list will be resorted in copied order upon re-entering Music List.
Select Contents
A
1. Press the BLUE(D) button to select Contents.
. Press the ▲▼ buttons to select the contents you want to move,
then Press the OK or + button.
CD
Music List
SONG 1.mp3
1/10
No.
Y
M
` This function is possible only when the disc contains the selected
contents.
` Audio CD(CD-DA) is not available.
Q
002
003
004
005
006
@ + # 00:02:22
9 SONG 1.mp3
E ROOT
Edit
Sort
[/] Previous/Next Page
66_ playback
Title
ROOT
SONG 1.MP3
SONG 2.MP3
SONG 3.MP3
SONG 4.MP3
SONG 5.MP3
SONG 6.MP3
Play Mode
a Check
Size
3.8 MB
5.8 MB
Title 5.1 MB
DivX 9.2 MB
Music 5.2 MB
10.3 MB
Photo (with
Music)
Contents
eExit
Music/Photo Simultaneous Playback
A
You can listen to the music while watching the photo.
1. Press the BLUE(D) button to select Contents.
CD
. Press the ▲▼ buttons to select the Photo(With Music), then
Press the OK or ► button.
The photo List will be displayed. (See pages 67~69.)
Music List
SONG 1.mp3
1/10
No.
Y
@ + # 00:02:22
M
9 SONG 1.mp3
E ROOT
` To operate this function, you have to select the disc containing both
music files and photo file.
Edit
ROOT
SONG 1.MP3
SONG 2.MP3
SONG 3.MP3
SONG 4.MP3
SONG 5.MP3
SONG 6.MP3
Sort
[/] Previous/Next Page
Size
3.8 MB
5.8 MB
Title 5.1 MB
DivX 9.2 MB
Music 5.2 MB
10.3Music)
MB
Photo (with
Play Mode
Contents
a Check
eExit
Viewing a Picture
G
1. Insert a JPEG disc into the disc tray.
~ The menu is displayed
CD
Photo List
1/17
Image 1.jpg
. Press the ▲▼ buttons to select Library, then press the OK or +
button.
. Press the ▲▼ buttons to select Photo, then press the OK or +
button.
~ To see the next 8 pictures, press the SKIP ( ) button.
~ To see the previous 8 pictures, press the SKIP ( ) button.
ROOT
Image 1.jpg
Image 10.jpg
Image 11.jpg
Image 13.jpg
Image 14.jpg
Image 15.jpg
Image 16.jpg
Edit
Sort
[/] Previous/Next Page
Slideshow
Contents
a Check
eExit
. Press the ▲▼_ + buttons to select a desired picture, then press
the OK button.
Slide Show
. Press the PLAY ( ) button.
~ Once in the Photo List, you can also operate Slide Show in by
pressing the YELLOW(C) button.
Image 1.jpg
1/17
. Press the RED(A) button to select Speed.
. Press the ▲▼ buttons to select the Slide Show speed, then press
the OK or + button.
The Slide Show starts and plays at the selected speed.
~ You can go to Photo List by pressing YELLOW(C) button.
❖ To stop the Slide Show
Press the GREEN(B), STOP(
mPhoto
Rotate
+ SlideShow
Zoom
rReturn
Image 1.jpg
eExit
1/17
) or RETURN button.
Fast
Normal
Slow
Speed
mPhoto
Slide Show Off + SlideShow
Photo List
rReturn
eExit
English _67
● Playback
Q
002
003
004
005
006
Title
playback
Rotate
To setup, follow steps 1 to 4 in page 67.
5-1. Press the GREEN(B) button to select Rotate.
Image 1.jpg
. Press the ▲▼ buttons to select the rotate angle, then press the
OK or + button.
~ Once you select a rotate angle, you can change it by pressing
the RED(A) button.
~ You can go to Photo List by pressing YELLOW(C) button.
Off
Rotate 90
Rotate 180
Rotate 270
Rotate ❖ To stop the Rotate
Press the GREEN(B), STOP(
1/17
mPhoto
+ SlideShow
Zoom
rReturn
eExit
) or RETURN button.
Rotate
Rotate Off
mPhoto
Photo List
rReturn
eExit
Zoom
To setup, follow steps 1 to 4 in page 67.
5-1. Press the YELLOW(C) button to select Zoom.
. Each time the OK button is pressed, the picture is enlarged up to
4x (four times the normal size).
 X2  X4  X2  Normal
~ You can go to Photo List by pressing YELLOW(C) button.
❖ To stop the Zoom
Press the GREEN(B), STOP(
) or RETURN button.
Go To Photo List
To setup, follow steps 1 to 4 in page 67.
5-1. Press the RETURN button to go to Photo List.
Using the Sort
When you need to change the Sort order of Photo List, you can change it simply.
To setup, follow steps 1 to 4 in page 67.
5-1. While the list menu is displayed, press the GREEN(B) button to select Sort.
. Press the ▲▼ buttons to select the desired item, then press the
OK or + button.
~ Name : In alphabetical order
~ Size : In order of photo file size.
M
CD
Photo List
01/17
Image 1.jpg
ROOT
Image 1.jpg
Image 10.jpg
Image 11.jpg
Image 13.jpg
Name
Size
Image 14.jpg
Image 15.jpg
Image 16.jpg
Edit
Sort
[/] Previous/Next Page
Slideshow
Contents
a Check
eExit
` You can sort by Name, Size. Sorted list will be resorted in copied order upon re-entering Photo List.
68_ playback
Select Contents
To setup, follow steps 1 to 3 in page 67.
1. Press the BLUE(D) button to select Contents.
CD
. Press the ▲▼ buttons to select the contents you want to move,
then Press the OK or + button.
Photo List
1/17
Image 1.jpg
ROOT
Image 1.jpg
Image 10.jpg
Image 13.jpg
Image 14.jpg
Image 15.jpg
Sort
[/] Previous/Next Page
M
Slideshow
Contents
a Check
eExit
● Playback
Edit
Image 11.jpg
Title
DivX
Music
Image 16.jpg
Photo
` This function is possible only when the disc contains the selected
contents.
Playing a DivX
N Using the MENU button
CD
1. Insert a DivX disc into the disc tray.
~ The menu is displayed
DivX List
Movie_01.avi
1/1
No.
ROOT
001 Movie_01.avi
Size
Y
. Press the ▲▼ buttons to select Library, then press the OK or +
button.
162.8 MB
3 DivX
E ROOT
. Press the ▲▼ buttons to select DivX, then press the OK or +
button.
. Press the ▲▼ buttons to select the avi file (DivX), then press the
OK or PLAY ( ) button.
Title
Edit
Sort
Subtitle Enc.
a Check
Contents
eExit
. When DivX file is played, you can use following functions. Pressing the STOP ( ) button once during
playback will display the file list, pressing the button again will exit the menu screen.
DivX Function Description
Function
Skip Scene
M
Description
During play, press the SKIP (
) buttons, it moves forward or backward 5 minutes.
Search Scene
During play, press the SEARCH (
(X 2, X 4, X 8)
) buttons and press again to search at a faster speed.
Slow Motion
In pause mode ( ), press the SEARCH ( ) button on the remote control. (1/2, 1/4, 1/8)
Reverse Slow Motion Play is not available.
Step Motion
In pause mode ( ), press the SKIP ( ) buttons on the remote control.
Reverse Step Motion Play is not available.
` Some DivX files created on a personal computer may not be play back. That is why Codec Type, Version and Higher
resolution over specification are not supported.
English _69
playback
DivX Subtitle Encoding
1. Press the YELLOW(C) button in the file list.
. Press the ▲▼ buttons to select a supported DivX subtitle
language by region, then press the OK button.
CD
DivX List
Movie_01.avi
1/1
No.
Title
ROOT
001 Movie_01.avi
Edit
162.8 MB
Western(Windows)
Central(Windows)
Greek(Windows)
Cyrillic(Windows)
3 DivX
E ROOT
M
Size
Y
Sort
Subtitle Enc.
a Check
Contents
eExit
Western
Afrikaans, Basque, Catalan, Danish, Dutch, English, Faeroese, Finnish, French, German, Icelandic,
Indonesian, Italian, Malay, Norwegian, Portuguese, Spanish, Swahili, Swedish
Central
English, Albanian, Croatian, Czech, Hungarian, Polish, Romanian, Serbian(Latin), Slovak, Slovenian
Greek
English, Greek
Cyrillic
English, Azeri, Belarusian, Bulgarian, Kazakh, Macedonian, Russian, Serbian, Tatar, Ukrainian, Uzbek
` If the subtitle language is displayed in broken fonts, change DivX Subtitle to the appropriate region. If is still does not
work, the format is not supported.
Using the Sort
When you need to change the Sort order of DivX List, you can change it simply.
1. While the list menu is displayed, press the GREEN(B) button to
select Sort.
CD
DivX List
Movie_01.avi
1/3
No.
. Press the ▲▼ buttons to select the desired item, then press the
OK or + button.
~ Name : In alphabetical order
~ Size : In order of DivX file size.
Title
ROOT
001 Movie_01.avi
002 Movie_02.avi
003 Movie_03.avi
3 DivX
E ROOT
M
162.8 MB
238.2 MB
118.4 MB
Name
Size
Edit
` You can sort by Name, Size. Sorted list will be resorted in copied
Size
Y
Sort
Subtitle Enc.
a Check
Contents
eExit
order upon re-entering DivX List.
Select Contents
1. Press the BLUE(D) button to select Contents.
. Press the ▲▼ buttons to select the contents you want to move,
then press the OK or + button.
CD
DivX List
Movie_01.avi
1/1
No.
Title
ROOT
001 Movie_01.avi
Edit
` This function is possible only when the disc contains the selected contents.
70_ playback
162.8 MB
Title
DivX
Music
Photo
3 DivX
E ROOT
M
Size
Y
Sort
Subtitle Enc.
a Check
Contents
eExit
recording
This section shows various HDD&DVD Recording methods.
This unit can record on various types of discs. Before recording, read the following
instructions and select the disc type according to your preference.
● Recording
Recordable Discs
This HDD & DVD Recorder can record on the following discs.
HDD
DVD-RAM
DVD-RW
DVD-R
DVD+RW
DVD+R
~ DVD-RAMs and DVD±RWs are rewritable.
~ DVD±Rs are non-rewritable.
Compatibility between Samsung and Other Company’s Recorder
Disc Types
DVD-RAM
Recording
format
Recording Device
VR Mode
Samsung
Other Company
DVD+R
DVD+R
DVD+ReWritable
DVD+ReWritable
Samsung
VR Mode
Other Company
DVD-RW
Samsung
V Mode
Other Company
Samsung
DVD-R
V Mode
Other Company
DVD+RW
-
Samsung
Other Company
Samsung
DVD+R
Finalising
Other Company
X
X
finalised
not finalised
finalised
not finalised
finalised
not finalised
finalised
not finalised
finalised
not finalised
finalised
not finalised
X
X
finalised
not finalised
finalised
not finalised
Additional Recording
in Samsung Recorder
Recordable
Recordable
Not recordable
Recordable
Not recordable
Recordable
Not recordable
Recordable
Not recordable
Not recordable
Not recordable
Recordable
Not recordable
Not recordable
Not recordable in some cases
Not recordable in some cases
Not recordable
Not recordable in some cases
Not recordable
Not recordable in some cases
English _71
recording
M
` Finalise
- This closes the DVD-RW/±R so no additional recording can be done.
` Unfinalise
- This allows additional recording on a DVD-RW disc originally recorded on the HDD & DVD Recorder.
- A DVD-RW disc that has been recorded by DAO(Disc At Once) in a PC cannot be unfinalised.
- A DVD-RW disc that has been recorded in Video Mode of a different maker’s recorder cannot be unfinalised.
- A DVD±R disc cannot be unfinalised.
` An additional recording could be failed in the same recorder of SAMSUNG.
Recording Formats
When you insert an unused disc, the following message appears. Since available functions differ depending on the
disc type, select a disc that best fits your preferences.
DVD-RAM/+R : Formatting will be started automatically.
DVD+RW : Use after formatting the disc.
DVD-RW : Use after initialising the disc.
If you want to change the VR or V mode, refer to Formatting a Disc on pages 103~104.
DVD-R : Formatting disc is unnecessary and only V Mode Recording is supported.
DVD-RAM/-RW(VR mode)
~ This mode allows multiple editing functions (such as deletion of the whole title, partial deletion of a title, etc.).
~ Various editing options using a created Playlist.
DVD-RW(V mode)/-R
~ Chapters will be created automatically when you finalise recording on DVD-RW/-R discs in V mode.
The chapter’s length (interval between chapters) varies according to the recording mode.
~ Simple editing (erasing titles/changing title name).
DVD+RW
~ With DVD+RW discs, there is no difference between DVD-Video format(Video mode) and DVD-Video
Recording format(VR mode).
72_ recording
Recording Mode
Select one of four recording modes by pressing the REC MODE button repeatedly while the unit is in Stop mode for
the desired recording time and picture quality. In general, picture quality improves as the recording time decreases.
In FR mode, the most suitable record mode is adjusted automatically, according to remaining time on the disc and
length of the timer recording. This function is selected only one mode in XP, SP, LP and EP modes and you can use
this mode for timer recording.
~ DVD-SH893
Recording Times
HDD (160GB)
DVD-RAM/±RW/±R
XP
(high quality mode)
Approx. 33 hours
Approx. 1 hour
about 8.5 Mbps
SP
(standard quality mode)
Approx. 67 hours
Approx. 2 hours
about 4.5 Mbps
LP
(long recording mode)
Approx. 133 hours
Approx. 4 hours
about 2 Mbps
EP
(extended mode)
FR
(Flexible Recording)
Approx. 6 hours/
about 1.6 Mbps
Approx. 8 hours/
about 1.2 Mbps
Approx. 199 hours
Approx. 264 hours
Approx. 33 hours ~ 264 hours
Approx. 1~8 hours
~ DVD-SH895
Recording Mode
Recording Times
HDD (250GB)
DVD-RAM/±RW/±R
XP
(high quality mode)
Approx. 53 hours
Approx. 1 hour
about 8.5 Mbps
SP
(standard quality mode)
Approx. 106 hours
Approx. 2 hours
about 4.5 Mbps
LP
(long recording mode)
Approx. 211 hours
Approx. 4 hours
about 2 Mbps
EP
(extended mode)
FR
(Flexible Recording)
Approx. 316 hours
Approx. 421 hours
Approx. 53 hours ~ 421 hours
Approx. 6 hours/
about 1.6 Mbps
Approx. 8 hours/
about 1.2 Mbps
Approx. 1~8 hours
English _73
● Recording
Recording Mode
recording
~ DVD-SH897
Recording Mode
HDD (320GB)
DVD-RAM/±RW/±R
XP
(high quality mode)
Approx. 68 hours
Approx. 1 hour
about 8.5 Mbps
SP
(standard quality mode)
Approx. 135 hours
Approx. 2 hours
about 4.5 Mbps
LP
(long recording mode)
Approx. 270 hours
Approx. 4 hours
about 2 Mbps
EP
(extended mode)
FR
(Flexible Recording)
M
Recording Times
Approx. 405 hours
Approx. 534 hours
Approx. 68 hours ~ 534 hours
Approx. 6 hours/
about 1.6 Mbps
Approx. 8 hours/
about 1.2 Mbps
Approx. 1~8 hours
` Recording time may vary according to specific conditions.
` 1GB = 1,000,000,000 bytes; actual formatted capacity may be less as the internal firmware uses a portion of the
memory.
` The dual layer DVD±Rs have approximately double the capacity of single layer DVD±Rs. (See pages 54~55)
` DVB-T recording is possible only on FR mode.
` On DVB-T recording, recording mode will be automatically determined depending on the quality of the video (or
audio).
74_ recording
Unrecordable Pictures
Video with copy protection cannot be recorded on this HDD & DVD Recorder.
When the HDD & DVD Recorder receives a copy- guard signal while recording, recording stops and the following
message appears on the screen.
Concerning Copy Control Signals
Signal type
Copy-Free
Copy-Once
Copy-Never
O
-
-
VR mode
O
O*
-
V mode
O
Media
DVD-RW (Ver.1.1)
DVD-RW(Ver.1.1)
with CPRM
-
DVD-R
O
DVD-RAM (Ver.2.0)
O
O*
-
DVD+RW
O
-
-
DVD+R
O
-
-
HDD
O
O*
-
Once “Copy Once” has been recorded, recording cannot be done anymore.
❖ Content Protection for Recordable Media (CPRM)
CPRM is a mechanism that ties a recording to the media on which it is recorded. It is supported by some
HDD & DVD Recorders, but not by many DVD players. Each blank recordable DVD has a unique 64-bit media
ID etched in the BCA. When protected content is recorded onto the disc, it can be encrypted with a 56-bit C2
(Cryptomeria) cipher derived from the media ID.
During playback, the ID is read from the BCA and used to generate a key to decrypt the contents of the disc.
If the contents of the disc are copied to other media, the ID will be absent or wrong and the data will not be
decryptable.
Recording Immediately
SXCVKL
Before you start
1. Check that the disc has enough available space for the recording.
. Press the HDD or DVD button.
If you select DVD, Press the OPEN/CLOSE button and place a recordable disc on the disc tray.
Press the OPEN/CLOSE button to close the disc tray.
Wait until LOAD disappears from the front panel display.
English _75
● Recording
TV broadcasts that contain copy control signals may have one of the following three signal types, Copy-Free,
Copy-Once and Copy-Never. If you want to record a copy-once type programme, use DVD-RW with CPRM
in VR Mode, DVD-RAM and HDD.
recording
Recording the current TV programme you are watching
1. Press the PROG (
) or number buttons to select the current
programme you want to record.
Record Mode
SP(35:12)
. Press the REC MODE button repeatedly, (or press the REC
MODE button and then press the ▲▼ buttons) to select the
recording speed(quality).
 SP  LP  EP  XP
. Press the REC button.
Information concerning the channel is displayed on the screen,
then recording begins.
Icon(! REC) is displayed on the front panel.
M
HDD
● Recording:
PR 1 [SP]
` The REC mode is disabled in the DTV.
Recording from external equipment you are watching
1. Press the SOURCE button to select the input source according to the connection you made.
The front panel display changes in the following sequence:
 PR Number  AV1  AV2  AV3  DV
If you connect a digital camcorder, press the SOURCE button to select DV. (See page 77)
. Press the REC MODE button repeatedly, (or press the REC MODE button, then press the ▲▼ buttons)
to select the recording speed (quality).
. Press the REC button.
Information concerning the external input mode is displayed on the screen, then recording begins.
Icon(! REC) is displayed on the front panel.
To pause recording
~ Press the REC PAUSE button to pause a recording in progress.
~ Press the REC PAUSE button again during pause to resume recording.
~ You can switch channels by pressing the PROG (
) buttons while recording pauses. (Analogue
broadcasting only)
~ If you select DV mode during rec pause, recording will be stopped.
If you change the input source during rec pause in DV mode, recording will be stopped.
M
` In DTV mode, if you press the REC PAUSE button:
- The channel will not be switched and the TV/RADIO key is disabled.
- Switching to the analog channel or changing the input source will be applied after the recording is stopped.
` In ANALOG mode, if you press the REC PAUSE button:
- Switching to DTV mode will be applied after the recording is stopped.
To stop recording
Press the STOP ( ) button to stop or finish a recording in progress.
~ When using DVD-RAM/±RW/±R discs, the message “Updating the information of disc. Please wait for a
moment” is displayed.
76_ recording
M
`
`
`
`
`
You can not change the recording mode while recording.
Recording will stop automatically if there is no free space left for recording.
Up to 99 titles can be recorded onto a DVD-RAM/-RW/-R disc, and up to 48 titles onto a DVD+RW/+R disc.
Up to 999 titles can be registered on the HDD.
HDD recording is available for up to 24 hours, and when recording for 24 hours, 3 titles will be recorded with each
being 8 hours in length.
` Do not use DVD-R authoring discs with this unit.
Copying from a Camcorder
SXCVKL
You may control the Camcorder using the IEEE1394 (DV) interface.
1. Connect the DV output jack of your camcorder to the DV input
jack on the front of your HDD & DVD Recorder using a DV cable.
Record Mode
SP(35:12)
. Press the HDD or DVD button.
If you select DVD, press the OPEN/CLOSE button and place a
recordable disc on the disc tray. Press the OPEN/CLOSE button
to close the disc tray. Wait until LOAD disappears from the front
panel display.
. Press the REC MODE button repeatedly to select the recording
speed(quality).
. Press the SOURCE button to select DV.
If the input is set to DV, a playback/record menu that enables
camcorder control appears on the top of the screen.
DV
. Select the Play (+) icon on the upper part of the screen to
playback the camcorder and find the starting position to copy.
. To start recording, use the _ + buttons to select Record (!)
icon in the top side of the screen, then press the OK button.
You can press the REC button of the remote control to start
recording.
The DV device is connected.
< MOVE
rRETURN
To stop recording
Press the STOP ( ) button to stop or finish a recording in progress.
~ When using DVD-RAM/±RW/±R discs, the message “Updating the information of disc. Please wait for a
moment” is displayed.
M
` To display playback related icons on the screen, press any direction button on the remote control.
English _77
● Recording
` Recording will stop automatically if a copy protected image is selected.
` DVD-RAM/±RW discs must be formatted before starting to record. Most new discs are sold unformatted.
recording
Making a One Touch Recording (OTR)
SXCVKL
You can set the HDD & DVD Recorder to record in 30-minute increments up to 8 hours by pressing the REC
button.
1. Press the HDD or DVD button.
If you select DVD, press the OPEN/CLOSE button and place a
recordable disc on the disc tray. Press the OPEN/CLOSE button
to close the disc tray. Wait until LOAD disappears from the front
panel display.
HDD
● Recording:
PR 1 [SP]
. Press the PROG (
) or number buttons to select the
programme to record.
. Press the REC button to start recording.
. Press the REC button repeatedly to adjust the desired recording
time.
OTR Mode
0:30
 0:30  1:00  ... 8:00  Off
M
` The timer counter decreases by the minute from 8:00 to 0:00, then
the HDD & DVD Recorder stops recording.
To stop recording
Press the STOP ( ) button. The message “Do you want to stop recording?” is displayed.
~ Press the _ + buttons to select Yes, then press the OK button.
~ Or press the STOP ( ) button again.
Simultaneous Recording and Playback
S
You can play back from the beginning of the programme you are currently recording.
You can watching the previous title list while recording a programme.
Using the PLAY ( ) button
1. With the unit in recording mode, press the PLAY ( ) button.
It plays back the title that you are currently recording from the
beginning.
Playback is not available for 10 seconds from the start of
recording.
You can use the SKIP (
) and other playback-related
buttons to view the previous recorded list.
78_ recording
HDD
► Play
Stopping Playback / Recording
1. Press the STOP (
) button. Playback screen disappears and the recording in progress screen appears.
. Pressing the STOP (
) button once more will stop the recording.
N Using the TITLE LIST button
. Press the OK or PLAY ( ) button.
It plays back the title that you are currently recording from the
beginning.
Title List
HDD
RECORDING...
4/4
No.
001
002
003
004
3 MPEG2
Title
JAN/01/2009 17:30 PR
JAN/01/2009 21:00 PR
JAN/01/2009 23:15 PR
RECORDING...
Length
01:00:00
01:00:00
00:30:00
00:00:00
eExit
4 JAN/02/2009 00:00
1 XP
N Using the MENU button
1. With the unit in recording mode, press the MENU button.
. Press the ▲▼ buttons to select Title, then press the OK button.
Title List screen is displayed.
. Press the ▲▼/SKIP (
) buttons to select the recording title list, then press the OK or + button.
It plays back the title that you are currently recording from the beginning.
Stopping Playback / Recording
1. Press the STOP (
) button once, playback screen disappears and the Title List screen appears.
. Pressing the MENU (
. Pressing the STOP (
M
) button again, the recording in progress screen appears.
) button once more will stop the recording.
` No sound is heard during search mode.
` DVD disc or HDD playback is available during HDD recording. However, JPEG, MP3, and DivX files in the disc cannot
be played back.
` HDD playback is available during DVD recording. However, JPEG and MP3 files in the HDD cannot be played back.
Time Shift function as a live signal
S
This function replays recordings as a live signal.
If you are interrupted while watching a TV programme, simply press the
TIME SHIFT button, and the HDD & DVD Recorder immediately starts
recording the programme.
Time Shift
>CHANGE
On
sSelect
English _79
● Recording
1. With the unit in recording mode, press the TITLE LIST button.
The above operation is possible from approx.10 seconds or more
after recording starts.
Press the ▲▼/SKIP (
) buttons to select the recording title
list.
recording
Using the Time Shift function
1. Press the TIME SHIFT button on the remote control.
The Time Shift menu is displayed.
. Press the ▲▼ button to select On, then press the OK button.
. While watching the currently broadcasting programme, press the PAUSE ( ) button.
The programme on TV is set in pause mode and the Time Shift Bar is displayed.
. Press the PLAY (
) button to resume watching the programme.
Time Shift Screen Elements
Informs you that the timeshift is currently working.
Displays the current status.
Watching Point.
13:25:04
+
Play
14:02:28
Current play time.
Live Point.
Live Time.
7
Time Shift Time Bar
Buttons on the Remote Control used for Time Shift function
1. PLAY (
) button : Playback.
2. PAUSE (
) button : Pause live TV.
3. SEARCH (
4. SKIP (
5. STOP (
) buttons : Fast play ( X 2, X 4, X 8, X 16, X 32, X 128)
) button, STOP (
) button : Moves to Live point.
) button : If you press this button in the Live point, a dialog box appears where you can stop
Time Shift.
6. SKIP (
) button : Returns to the point where Time Shift begins.
7. EXIT (
) or RETURN (
) button : Hides the Time Shift icon or the time bar.
8. _ + : Display Time shift Progressive Bar.
M
` The Time Shift is available only when HDD mode is selected.
` You can use this function for up to maximum two hours.
` You can only play the contents by using the menu when the Time Shift is set to On.
` Press TIME SHIFT button to cancel the Time shift function.
80_ recording
Making a Timer Recording
SXCVKL
1. Check if the antenna cable is connected.
2. Check if the remaining time of the disc.
3. Check if the date and time are correct.
Make sure the Clock (Setup-Clock Set) is set before you proceed with a timer recording. (See pages 37~38)
1. With the unit in Stop mode, press the TIMER button.
HDD & DVD RECORDER
Timer Record
HDD
. Press the $% button to select the Scheduled List, then press
the OK or + button.
. Press the OK button to select Add a list.
Library
Scheduled List
►
Guide
Recorded List
►
Channel
. Set timer recording option.
~ Fill the input items using the ▲▼_ + buttons and number
buttons.
_ + : Moves to the previous/next item.
▲▼, 0~9 : Sets a value.
~ To : Select the media to record HDD or DVD.
~ Source : The video input source (AV1, AV2 or AV3), or the
broadcasting channel you want to make a timer recording from.
To convert DTV/Analogue, press DTV/ANALOG button of the
remote control.
On the DTV mode, you can change TV or RADIO by pressing the
TV/RADIO button on the remote control.
~ Date : Timer Recording allows setting the recording time within
one month period. Set the recording day. (month/day)
Timer Record
Disc Manager
Setup
m MOVE
sSELECT
rRETURN
eEXIT
HDD
Scheduled List
Current Time 10:54
No.
To
Source Date
Start
End
Mode VPS/PDC
Add a list
Recordable Time HDD 69:30 SP
< MOVE
sSELECT
Recorded List
rRETURN
eEXIT
HDD
Scheduled List
Current Time 10:54
No.
JAN 31
To
To
JAN 30
HDD
JAN 29
Every SAT
MON-FRI
JAN 02
MON-SAT
JAN 01
Every Day
Source Date
Start
End
Mode VPS/PDC
No.01 No Title
Every SUN
Source Date
AV 1
JAN 01
Start
End
12:00
14:00
Recordable Time HDD 69:30 SP
Mode VPS/PDC
SP
Recordable Time HDD 69:30 SP
< MOVE
sSELECT
Off
Title sSave
Recorded List
rRETURN
eEXIT
~ Start/End Time : Start and end time of the timer recording.
~ Mode (Recording Mode) :
- FR (Flexible Recording) : Select when you want to set video quality automatically. In FR mode, the most
suitable record mode is adjusted automatically, according to the remaining time on the disc and length of
the timer recording. This function is selected only one mode in XP, SP, LP and EP modes.
- XP (high quality) : Select when video quality is important.
- SP (standard quality) : Select to record in standard quality.
- LP (low quality) : Select when a long recording time is required.
- EP (extended) : Select when a longer recording time is required.
M
` DVB-T Timer recording is possible only on FR mode.
` On DVB-T recording, recording mode will be automatically determined depending on the quality of the video
(or audio).
English _81
● Recording
N Using the TIMER button
recording
~ VPS/PDC : VPS(Video Programme System) or PDC (Programme Delivery Control) function.
- If you set this function on, you can control the starting and ending time of recording by special
signal included in the broadcasting signal. If a TV programme is shortened or starts earlier or
later than scheduled, this function synchronizes the starting and ending time of recording with
the actual broadcasting time automatically.
- Set up the start-time EXACTLY according to the published TV schedule. Otherwise the timer
recording will not operate.
- Do not select PDC or VPS unless you are sure the programme you wish to record is
broadcast with PDC or VPS.
~ TITLE : To label the title name, press the RED(A) button.
Title renaming screen appears.
Follow steps 4 and 5 of “Renaming (Labeling) a Title” on pages 86~87.
. After selecting the set up value for each mode, press the OK button to select Save.
~
will appear on the front panel. It means that a timer recording is registered.
If the timer settings overlap;
The programmes are recorded in order of priority. After recording of the first programme is complete, the
second programme starts being recorded.
To exit without saving the current setting
Press the EXIT ( ) button.
To return to the previous menu
Press the RETURN button if you don’t want to set a timer recording.
. Turn the power off to finish the Timer Recording setting.
Timer Recording will not work when the power is on.
M
` The timer recording time may differ from the set time depending on disc status and overall timer recording status
(for example, recording times overlapping, or when the previous recording ends within 2 minutes before the start
time of the next recording.)
` You can make the Timer Recording up to 12 programmes.
` If HDD disk has no available recording space,
blinks. It means that HDD disk has no space to record.
` If you have set the Timer Recording using VPS/PDC, the fan can still operate and make a noise when the power is
off.
Editing the Scheduled List
Follow these directions to edit the Scheduled List.
N Using the TIMER button
1. With the unit in Stop mode, press the TIMER button.
HDD & DVD RECORDER
. Press the $% button to select the Scheduled List, then press
the OK or + button.
Timer Record
HDD
Library
Scheduled List
►
Guide
Recorded List
►
Channel
Timer Record
Disc Manager
Setup
82_ recording
m MOVE
sSELECT
rRETURN
eEXIT
. Press the ▲▼ buttons to select the number of the Scheduled List
you want to edit, then press the OK button.
~ Edit the items you want to modify. See the “Making a Timer
Recording” section for more information on Timer Recording
Input items. (See pages 81~82)
HDD
No. To Source Date
- -
- - -
----
-- -01 HDD PR 01 JAN 01
02 HDD PR 01 JAN 01
03 HDD PR 01 JAN 01
. Press the OK button to confirm the edited setting.
. Press the EXIT ( ) button after finishing the operation.
The Scheduled List screen will disappear.
Scheduled List
Current Time 10:54
Start
- -:- 17:30
21:00
23:15
End
- -:- 18:30
22:00
23:45
Mode VPS/PDC
- -
-SP
On
SP
On
SP
On
Recordable Time HDD 65:19 XP
Add
Delete
Recorded List
m MOVE
rRETURN
sSELECT
eEXIT
● Recording
Adding a Scheduled List
Follow these directions to add an entry from the Scheduled List.
N Using the TIMER button
1. With the unit in Stop mode, press the TIMER button.
HDD
. Press the $% button to select the Scheduled List, then press
the OK or + button.
. Press the ▲▼ buttons to select the number of the Scheduled
List, then press the RED(A) button.
~ Set the items you want to add. See the “Making a Timer
Recording” section for more information on Timer Recording
Input items. (See pages 81~82)
Scheduled List
Current Time 10:54
No. To Source Date
- -
- - -
----
-- -01 HDD PR 01 JAN 01
02 HDD PR 01 JAN 01
03 HDD PR 01 JAN 01
. Press the OK button to confirm the added setting.
Start
- -:- 17:30
21:00
23:15
End Mode VPS/PDC
- -:- - -
-18:30 SP
On
22:00 SP
On
23:45 SP
On
Recordable Time HDD 65:19 XP
Add
Delete
Recorded List
m MOVE
rRETURN
sSELECT
eEXIT
HDD
. Press the EXIT ( ) button after finishing the operation.
The Scheduled List screen will disappear.
Scheduled List
Current Time 10:54
No.
To
Source Date
Start
End
Mode VPS/PDC
No.01 No Title
To
HDD
Source Date
PR 01
JAN 01
Start
End
17:30
18:30
Recordable Time HDD 108:14 SP
Mode VPS/PDC
SP
Recordable Time HDD 65:19 XP
Add
Delete
Recorded List
< MOVE
rRETURN
sSELECT
On
Title sSave
HDD
eEXIT
Scheduled List
Current Time 10:54
No.
- -
01
02
03
04
To Source Date
- - -
----
-- -HDD PR 01 JAN 01
HDD PR 01 JAN 01
HDD PR 01 JAN 01
HDD PR 01 JAN 02
Start
- -:- 17:30
21:00
23:15
17:30
End
- -:- 18:30
22:00
23:45
18:30
Recordable Time HDD 65:19 XP
Add
Delete
Recorded List
m MOVE
rRETURN
sSELECT
Mode VPS/PDC
- -
-SP
On
SP
On
SP
On
SP
On
eEXIT
English _83
recording
Deleting a Scheduled List
SXCVKL
Follow these directions to delete an entry from the Scheduled List.
N Using the TIMER button
1. With the unit in Stop mode, press the TIMER button.
. Press the $% button to select the Scheduled List, then press the OK or + button.
. Press the ▲▼ buttons to select the number of the Scheduled List you want to delete, and then press the
GREEN(B) button.
~ You will be prompted with the delete confirm message such as “Do you want to delete?”.
. Press the _ + buttons to select Yes, then press the OK button.
~ The selected entry will be deleted from the list.
. Press the EXIT ( ) button after finishing the operation.
The Scheduled List screen will disappear.
Go To Recorded List
SXCVKL
You can confirm the performance results of title lists that have passed the reserved recording time.
N Using the TIMER button
1. With the unit in Stop mode, press the TIMER button.
Recorded List
HDD
. Press the ▲▼ button to select Recorded List, then press the
OK or + button.
No.
01
02
03
. Press the EXIT ( ) button after finishing the operation.
The Recorded List screen will disappear.
To
HDD
HDD
HDD
Delete
> MOVE
Source Date Start End
PR 01 JAN 01 17:30 18:30
PR 01 JAN 01 21:00 22:00
PR 01 JAN 01 23:15 23:45
Delete All
Mode VPS/PDC Status
SP
On
OK
SP
On
OK
SP
On
OK
Scheduled List
sSELECT
rRETURN
eEXIT
Information about Recorded List
Informs whether the selected Recorded List performed a Timer
Recording successfully.
HDD
No.
01
02
03
3-1. Press the ▲▼ buttons to select the number of the Recorded
List, then press the OK button.
Recorded List
To
HDD
HDD
HDD
Source Date Start End Mode VPS/PDC
PR 01 JAN 01 17:30 18:30
SP
On
PR 01 JAN 01 21:00 22:00
SP
On
PR
01
JAN
01
23:15
23:45
S
P
On
Timer rec was finished successfully
Status
OK
OK
OK
OK
Delete
84_ recording
Delete All
sSELECT
Scheduled List
rRETURN
eEXIT
Delete Recorded List
Deletes a Recorded List individually.
Recorded List
HDD
3-1. Press the ▲▼ buttons to select the number of the Recorded List you want to delete, and then press the RED(A) button.
4. Press the _ + buttons to select Yes, then press the OK button.
To
HDD
HDD
HDD
Source
PR 01
PR 01
PR 01
Date Start End Mode VPS/PDC Status
JAN 01 17:30
SP
On
OK
No.01 18:30
JAN 01 21:00 22:00
SP
On
OK
JAN
01
23:15
23:45
S
P
On
OK
Do you want to delete?
Yes
No
Delete
Delete All
m MOVE
sSELECT
Scheduled List
rRETURN
eEXIT
Clear Recorded List
Clears all Recorded List at once.
Recorded List
HDD
3-1. Press the GREEN(B) button.
No.
01
02
03
4. Press the _ + buttons to select Yes, then press the OK button.
To Source Date Start End Mode VPS/PDC
HDD PR 01 JAN 01 17:30 18:30
SP
On
HDD PR 01 JAN 01 21:00 22:00
SP
On
HDD Do
PRyou
01 want
JAN 01to delete
23:15 a23:45
S
P
On
recorded list??
Yes
Status
OK
OK
OK
No
Delete
Delete All
m MOVE
sSELECT
Scheduled List
rRETURN
eEXIT
Go to Scheduled List
Switches directly from the Recorded List to the Scheduled List.
HDD
Scheduled List
3-1. Press the YELLOW(C) button.
Current Time 10:54
No.
To
Source Date
Start
End
Mode VPS/PDC
Add a list
Recordable Time HDD 105:44 SP
< MOVE
sSELECT
Recorded List
rRETURN
eEXIT
English _85
● Recording
No.
01
02
03
editing
This section introduces basic functions of editing and explains both edit functions for the
recording on a disc and edit functions for the entire disc.
Recording or editing might not be completed if an error, such as a sudden power failure
occurs. Please be aware that a material that has been damaged is unable to be retrieved
to its original content.
Basic Editing (Title List)
Playing the Title
SXCVKL
Follow these instructions to play back a scene from the Title List.
N Using the TITLE LIST button
1. With the unit in Stop mode/Playback mode, press the
TITLE LIST button.
1/3
No.
Title
001 JAN/01/2009 17:30 PR
002 JAN/02/2009 21:00 PR
003 JAN/03/2009 23:15 PR
. Press the $% buttons to select an entry you want to play from
Title List, then press the OK or PLAY ( ) button.
The selected entry (title) will be played back.
. To stop title play, press the STOP( ) button.
The screen returns to the Title List screen.
Title List
HDD
JAN/01/2009 17:30 PR1
Length
01:00:00
01:00:00
00:30:00
3 MPEG2
4 JAN/01/2009 17:30
1 SP
V-Mode Compatibility
Edit
Sort
Go to
Contents
a Check
eExit
Renaming (Labeling) a Title
SXCVKL
Follow these instructions to rename a title list entry, i.e., to edit the title of a recorded programme.
N Using the TITLE LIST button
1. With the unit in Stop mode/Playback mode, press the
TITLE LIST button.
Title List
HDD
JAN/01/2009 17:30 PR1
. Press the ▲▼ buttons to select an entry you want to rename
from the Title List, then press the RED(A) button.
. Press the ▲▼ buttons to select Rename, then press the OK or
+ button.
The Rename screen is displayed.
. Select the desired characters using the ▲▼_ + buttons, press
the OK button.
~ Back Space (RED(A) button) : Deletes and moves the cursor
backwards by one position.
~ Space (GREEN(B) button) : Enters a blank and moves the
cursor one forward (to the right).
~ Clear (YELLOW(C) button) : Deletes all the character inputs.
~ Save (BLUE(D) button) : Registers the character inputs.
Length
01:00:00
01:00:00
00:30:00
3 MPEG2
4 JAN/01/2009 17:30
1 SP
V-Mode Compatibility
Edit
Sort
Go to
Contents
a Check
eExit
Title List
HDD
JAN/01/2009 17:30 PR1
Delete
Copy
Rename
Protection
Partial Delete
3 MPEG2
Split
4 JAN/01/2009 17:30
New
1 SPPlaylist
Select
All
V-Mode Compatibility
Edit
86_ editing
1/3
No.
Title
001 JAN/01/2009 17:30 PR
002 JAN/02/2009 21:00 PR
003 JAN/03/2009 23:15 PR
1/3
No.
Title
001 JAN/01/2009 17:30 PR
002 JAN/02/2009 21:00 PR
003 JAN/03/2009 23:15 PR
Sort
Length
01:00:00
01:00:00
00:30:00
Go to
Contents
a Check
eExit
. Press the BLUE(D) button to select Save.
The changed title name is displayed on the title item of the
selected entry.
Rename
HDD
Sports(A1)
Space
sSELECT
Clear
rRETURN
● Editing
Back Space
m MOVE
Save
eEXIT
Locking (Protecting) a Title
SXCVKL
Follow these instructions to lock an entry to protect it from accidental edition.
N Using the TITLE LIST button
1. With the unit in Stop mode/Playback mode, press the
TITLE LIST button.
. Press the ▲▼ buttons to select an entry you want to protect
from the Title List, then press the MARKER button until a
checkmark appears. Repeat this step to select an additional title
you want to protect.
~ If you don’t want to protect a certain one of the checked
entries, simply select that entry and press the MARKER to
deselect it until a checkmark disappears.
. Press the RED(A) button to select Edit. Edit menu is displayed.
. Press the ▲▼ buttons to select Protection, then press the OK or
+ button.
. Press the _ + buttons to select On, then press the OK button.
The key icon on the information window for the selected entry
changes to the locked status. (10)
. If you want to cancel the Protection, select Off in step 5 and press
the OK button. The key icon changes to the unlocked status.
(01)
M
Title List
HDD
JAN/02/2009 21:00 PR1
Delete
Copy
Protection
3 MPEG2
New
Playlist 17:30
4 JAN/01/2009
Select
1 SP All
V-Mode Compatibility
Unselect
All
Edit
2/3
No.
Title
001 JAN/01/2009 17:30 PR
002 JAN/02/2009 21:00 PR
003 JAN/03/2009 23:15 PR
Sort
Length
01:00:00
01:00:00
00:30:00
Go to
Contents
a Check
eExit
Title List
HDD
JAN/02/2009 21:00 PR1
2/3
No.
Title
001 JAN/01/2009 17:30 PR
002 JAN/02/2009 21:00 PR
2 items are selected
003 JAN/03/2009 23:15 PR
Set title Protection mode:
Protection
3 MPEG2
4 JAN/01/2009 17:30
1 SP
On
Length
01:00:00
01:00:00
00:30:00
Off
V-Mode Compatibility
Edit
< MOVE
Sort
sSELECT
Go to
Contents
rRETURN
eExit
` If you select “Select All” in the Edit menu, all title will be checked.
English _87
editing
Deleting a Title
SXCVKL
Follow these instructions to delete an entry from the Title List.
N Using the TITLE LIST button
1. With the unit in Stop mode/Playback mode, press the
TITLE LIST button.
. Press the ▲▼ buttons to select an entry you want to delete in
the Title List, then press the MARKER button until a checkmark
appears. Repeat this step to select an additional title you want to
delete.
~ If you don’t want to delete a certain one of the checked entries,
simply select that entry and press the MARKER to deselect it
until a checkmark disappears.
Title List
HDD
JAN/02/2009 21:00 PR1
Delete
Copy
Protection
3 MPEG2
New
Playlist 17:30
4 JAN/01/2009
Select
1 SP All
V-Mode Compatibility
Unselect
All
Edit
. Press the RED(A) button to select Edit.
Edit menu is displayed.
2/3
No.
Title
001 JAN/01/2009 17:30 PR
002 JAN/02/2009 21:00 PR
003 JAN/03/2009 23:15 PR
Sort
Length
01:00:00
01:00:00
00:30:00
Go to
Contents
a Check
eExit
Title List
HDD
JAN/02/2009 21:00 PR1
2/3
No.
Title
001 JAN/01/2009 17:30 PR
2 items002
areJAN/02/2009
selected 21:00 PR
Do you 003
wantJAN/03/2009
to delete?23:15 PR
(Related playlists may be deleted.)
. Press the ▲▼ buttons to select Delete, then press the OK or +
button.
~ The message may be different depending on the type of disc.
Yes
You will be prompted with the confirmation message.
Edit
Sort
HDD, DVD-RAM(VR mode), DVD-RW(VR mode) : The message
< MOVE
sSELECT
“Do you want to delete? (Related playlists may be deleted.)” is
displayed.
DVD-RW(V mode)/±RW/±R : The message “Do you want to delete?” is displayed.
3 MPEG2
4 JAN/01/2009 17:30
1 SP
Length
01:00:00
01:00:00
00:30:00
No
V-Mode Compatibility
Go to
Contents
rRETURN
eExit
. Press the _ + buttons to select Yes, then press the OK button.
M
` You cannot delete a protected entry. If you want to delete a protected entry, select “Off” in the Title Protection menu.
(See page 87)
` When the Disc Protection has been set to Protected, you cannot delete titles. (See page 102)
` Once an entry is deleted from the Title List it cannot be recovered.
` Once DVD-RW/±R is finalised, it cannot be deleted.
` With DVD±R, titles are only deleted from the menu, however, the Title remains physically on the disc.
` If you select “Select All” in the Edit menu, all title will be checked.
Splitting a Section of a Title (Split)
SK
Follow these instructions to split a section of a Title List entry into two titles.
N Using the TITLE LIST button
1. With the unit in Stop mode/Playback mode, press the
TITLE LIST button.
Title List
HDD
JAN/01/2009 17:30 PR1
Delete
Copy
Rename
Protection
Partial Delete
3 MPEG2
Split
4 JAN/01/2009 17:30
New
1 SPPlaylist
Select
All
V-Mode Compatibility
. Press the ▲▼ buttons to select an entry you want to Split from
the Title List, then press the RED(A) button.
The Edit menu is displayed.
Edit
88_ editing
1/3
No.
Title
001 JAN/01/2009 17:30 PR
002 JAN/02/2009 21:00 PR
003 JAN/03/2009 23:15 PR
Sort
Length
01:00:00
01:00:00
00:30:00
Go to
Contents
a Check
eExit
. Press the ▲▼ buttons to select Split, then press the OK or +
button.
Title List No. 001
Split 1
Split 2
00:00:00
00:00:00
00:00:01
Return
►
Select
+ Play
Split
< MOVE
( ) SCAN
# Pause
sSELECT
rRETURN
eEXIT
. Press the OK button to select Split.
Split
HDD
. Press the _ + buttons to select Yes, then press the OK button.
The split title is divided into two, and the following titles will be
shifted down by one.
JAN/01/2009 17:30 PR1
Title List No. 001
Split 1
Split 2
00:00:00
00:00:20
00:00:20
Return
#
Select
+ Play
Split
# Pause
< MOVE
( ) SCAN
sSELECT
rRETURN
eEXIT
Split
HDD
JAN/01/2009 17:30 PR1
Title List No. 001
Split 1
Split 2
This title cannot be recovered
after splitting.
Do you want to split?
00:00:00
No
Yes
#
Select
+ Play
Split
( ) SCAN
# Pause
< MOVE
00:00:20
00:00:20
Return
sSELECT
rRETURN
eEXIT
Deleting a Section of a Title (Partial Delete)
SXCK
(VR mode)
Follow these instructions to delete a section of a Title List entry.
N Using the TITLE LIST button
1. With the unit in Stop mode/Playback mode, press the
TITLE LIST button.
. Press the ▲▼ buttons to select Partial Delete, then press the
OK or + button.
Edit
. Press the OK button at the starting point.
The image and starting point time is displayed in the section
deletion starting point window.
~ Select the start and end points of the section you want to delete
using the playback related buttons.
~ Playback related buttons : (PLAY ( ), PAUSE ( ),
SEARCH (
)).
1/3
No.
Title
001 JAN/01/2009 17:30 PR
002 JAN/02/2009 21:00 PR
003 JAN/03/2009 23:15 PR
Delete
Copy
Rename
Protection
Partial Delete
3 MPEG2
Split
4 JAN/01/2009 17:30
New
1 SPPlaylist
Select
All
V-Mode Compatibility
. Press the ▲▼ buttons to select an entry you want to edit from
the Title List, then press the RED(A) button.
The Edit menu is displayed.
. Press the OK button at the end point.
The image and end point time is displayed in the Section deletion
ending point window.
Title List
HDD
JAN/01/2009 17:30 PR1
Sort
Length
01:00:00
01:00:00
00:30:00
Go to
Contents
a Check
eExit
Partial Delete
HDD
JAN/01/2009 17:30 PR1
Title List No. 001
Start
End
00:19:10
►
Start
+ Play
End
# Pause
< MOVE
Delete
00:41:20
00:41:20
Return
( ) SCAN
sSELECT
rRETURN
eEXIT
English _89
● Editing
. Using the playback-related buttons (PLAY ( ), PAUSE ( ),
SEARCH (
), move to a point for splitting and press the OK
button.
If it is not the point where you want to split, press the RETURN
button to cancel the selection. Using the playback-related
buttons, move to a point to split and press the OK button.
Split
HDD
JAN/01/2009 17:30 PR1
editing
. Press the _ + buttons to select Delete, then press the OK
button.
Partial Delete
HDD
JAN/01/2009 17:30 PR1
Title List No. 001
Start
End
Do you want to delete?
(Deleted part will not be restored.)
. Press the _ + buttons to select Yes, then press the OK button.
The selected section has been deleted.
. Press the _ + buttons to select Return, then press the OK
button to finish the operation.
#
Start
+ Play
Delete
# Pause
< MOVE
M
End
00:19:10
No
Yes
00:41:20
00:41:20
Return
( ) SCAN
sSELECT
rRETURN
eEXIT
` The length of the section to be deleted must be at least 5 seconds long.
` End point cannot be marked earlier than start point
` The section cannot be deleted when it includes a still picture.
` Press the EXIT (
) button after the operation has finished.
The Title List screen will disappear.
Using the Sort function (Title List)
SXCVKL
When you need to change the Sort order of Title List, you can change it simply. You can sort by Date, Name,
Length, Channel info. Sorted list will be resorted in chronological order upon re-entering Title List.
1. While the list menu is displayed, press the GREEN(B) button to
select Sort.
. Press the ▲▼ buttons to select the desired item, then press the
OK or + button.
~ Date : In order of when the titles were recorded
~ Name : In alphabetical order
~ Length : In order of recorded title length.
~ Channel Info : In order of Channel information.
M
Title List
HDD
JAN/01/2009 17:30 PR1
1/3
No.
Title
001 JAN/01/2009 17:30 PR
002 JAN/02/2009 21:00 PR
003 JAN/03/2009 23:15 PR
3 MPEG2
Date
Name
4 JAN/01/2009 17:30
Length
1 SP
Channel
V-Mode Compatibility
Edit
Length
01:00:00
01:00:00
00:30:00
Info
Sort
Go to
Contents
a Check
eExit
` You can sort by Date, Name, Length, Channel info. Sorted list will be resorted in copied order upon re-entering Title
List.
Navigation Menu
Time Navigation
SXC
(VR mode)
Using this function, you can search scene minute-by-minute from the recorded title list.
N Using the TITLE LIST button
1. With the unit in Stop mode/Playback mode, press the
TITLE LIST button.
Title List
HDD
JAN/01/2009 17:30 PR1
. Press the $% buttons to select Time Navigation, then press the
OK or + button.
3 MPEG2
V-Mode Compatibility
Sort
Length
01:00:00
01:00:00
00:30:00
Playlist
Time Navigation
Scene Navigation
4 JAN/01/2009 17:30
1 SP
Edit
90_ editing
1/3
No.
Title
001 JAN/01/2009 17:30 PR
002 JAN/02/2009 21:00 PR
003 JAN/03/2009 23:15 PR
. Press the $% buttons to select an entry you want to play from
Title List, then press the YELLOW(C) button.
Go to
Contents
a Check
eExit
. Press the _ + buttons to skip one minute at a time and search
the desired scene, then press the OK or PLAY ( ) button.
M
Time Navigation
HDD
3 JAN/01/2009 17:30 PR1
1/3
` Cursor does not move if the selected recorded title is shorter than 1
minute.
►
17:30
recorded by this device.
` An edited title may not display the exact search time.
● Editing
00:00
` The Navigation function may not work on a disc that has not been
18:30
< MOVE
sSELECT
rRETURN
eEXIT
Scene Navigation
SXC
(VR mode)
If there is a title composed of markers (See page 61), you can search the desired scene using the Scene
Navigation.
N Using the TITLE LIST button
1. With the unit in Stop mode/Playback mode, press the
TITLE LIST button.
. Press the $% buttons to select an entry you want to play from
Title List, then press the YELLOW(C) button.
M
1/3
No.
Title
001 JAN/01/2009 17:30 PR
002 JAN/02/2009 21:00 PR
003 JAN/03/2009 23:15 PR
. Press the $% buttons to select Scene Navigation, then press
the OK or + button.
. Press the $%_ + buttons to select desired scene, then press
the OK or PLAY ( ) button.
Title List
HDD
JAN/01/2009 17:30 PR1
3 MPEG2
Playlist
Time Navigation
Scene Navigation
4 JAN/01/2009 17:30
1 SP
V-Mode Compatibility
Edit
Sort
` Scene Navigation will not operate if a selected title does not have
Go to
Contents
a Check
eExit
Scene Navigation
HDD
Markers.
JAN/01/2009 17:30 PR1
01 00:00:05
Length
01:00:00
01:00:00
00:30:00
Scene No. 1/3
02 00:00:35
03 00:01:05
sPLAY
eExit
Select Contents
SXCVKL
1. Press the BLUE(D) button to select Contents.
. Press the ▲▼ buttons to select the contents you want to move,
then press the OK or + button.
M
Title List
HDD
JAN/01/2009 17:30 PR1
` This function is possible only when the disc contains the selected
contents.
3 MPEG2
4 JAN/01/2009 17:30
1 SP
V-Mode Compatibility
Edit
1/3
No.
Title
Length
001 JAN/01/2009 17:30 PR
01:00:00
002 JAN/02/2009 21:00 PR
01:00:00
003 JAN/03/2009 23:15 PR
00:30:00
Title
DivX
Music
Photo
Sort
Go to
Contents
a Check
eExit
English _91
editing
Advanced Editing (Playlist)
Creating a Playlist
SXC
(VR mode)
Follow these instructions to create a new playlist entry from a recorded title.
N Using the TITLE LIST button
1. With the unit in Stop mode/Playback mode, press the
TITLE LIST button.
. Press the ▲▼ buttons to select New Playlist, then press the OK
or + button.
The Make Playlist screen is displayed.
Edit
. Press the OK button at the start point.
~ The image and time at the start point is displayed on the Start
window.
~ The yellow-coloured selection bar moves to the End item.
~ Select the starting point of the section from which you want to
create a new scene using the playback related buttons
(PLAY ( ), PAUSE ( ), SEARCH (
), SKIP (
)).
. Press the _ + buttons to select Make, then press the OK
button.
~ To make a scene for the playlist.
A new Make scene screen is displayed. Repeat steps 4~6 to
make a new scene for the playlist. A new scene will be added to
the current playlist. You can check and see all the scenes on
the Edit playlist screen. (See pages 92~96)
~ To make a new playlist.
Repeat steps 1~6 if you want to make a new playlist.
1/3
No.
Title
001 JAN/01/2009 17:30 PR
002 JAN/02/2009 21:00 PR
003 JAN/03/2009 23:15 PR
Delete
Copy
Rename
Protection
Partial Delete
3 MPEG2
Split
4 JAN/01/2009 17:30
New
1 SPPlaylist
Select
All
V-Mode Compatibility
. Press the RED(A) button.
The Edit menu is displayed.
. Press the OK button at the end point.
~ The image and end point time is displayed in the End window.
~ The yellow-coloured selection bar moves to the Make item.
Title List
HDD
JAN/01/2009 17:30 PR1
Sort
Go to
Contents
a Check
eExit
Make Playlist
HDD
New Playlist
Scene No. 001
Start
Title List 1/3
End
+ Play
00:08:38
Make
( ) SCAN
# Pause
< MOVE
sSELECT
[ ] SKIP
rRETURN
eEXIT
Make Playlist
HDD
Scene No. 001
Start
Title List 1/3
00:08:38
#
End
Start
+ Play
Make
# Pause
< MOVE
` Depending on the kind of disc, the displayed screen may have a slight difference.
92_ editing
00:00:00
00:08:38
Return
New Playlist
` You can create up to 99 playlist entries.
` If the related title is erased, the playlist is also erased.
End
►
Start
( ) SCAN
sSELECT
. Press the _ + button to select Return, then press the OK button to finish the operation.
M
Length
01:00:00
01:00:00
00:30:00
rRETURN
End
00:11:03
00:11:03
Return
[ ] SKIP
eEXIT
Playing Entries in the Playlist
SXC
(VR mode)
N Using the PLAY LIST button
1. With the unit in Stop mode/Playback mode, press the PLAY
LIST button.
Playlist
HDD
JAN/02/2009 13:47
1/3
No.
Title
001 JAN/02/2009 13:47
002 JAN/02/2009 13:51
003 JAN/02/2009 14:08
. Press the ▲▼ buttons to select the playlist you want to play,
then press the OK or PLAY ( ) button.
. Press the STOP ( ) button to stop playing.
The screen returns to the Playlist screen.
Length
00:06:09
00:03:33
00:01:54
� PLAYLIST
4 JAN/02/2009 13:47
� 6 Scenes
Edit
Sort
Title List
a Check
eExit
Renaming a Playlist Entry
SXC
(VR mode)
Follow these instructions to rename a playlist entry, i.e. to edit the title of a playlist entry.
N Using the PLAY LIST button
1. With the unit in Stop mode/Playback mode, press the PLAY LIST
button.
Playlist
HDD
JAN/02/2009 13:47
1/3
No.
Title
001 JAN/02/2009 13:47
002 JAN/02/2009 13:51
003 JAN/02/2009 14:08
. Press the ▲▼ buttons to select the title you want to Rename
from the Playlist, then press the RED(A) button.
The Edit menu is displayed.
Length
00:06:09
00:03:33
00:01:54
� PLAYLIST
4 JAN/02/2009 13:47
. Press the ▲▼ buttons to select Rename, then press the OK or
+ button.
The Rename screen is displayed.
� 6 Scenes
Edit
. Select the desired characters using the ▲▼_ + buttons, then
press the OK button.
~ Back Space (RED(A) button) : Deletes and moves the cursor
backwards by one position.
~ Space (GREEN(B) button) : Enters a blank and moves the
cursor one forward (to the right).
~ Clear (YELLOW(C) button) : Deletes all the character inputs.
~ Save (BLUE(D) button) : Registers the character inputs.
Sort
Title List
a Check
eExit
Playlist
HDD
JAN/02/2009 13:47
Delete
Copy
Rename
� PLAYLIST
Edit
Playlist
4 JAN/02/2009 13:47
New
Playlist
� 6 Scenes
Select All
Edit
. Press the BLUE(D) button to select Save.
The changed title is displayed in the title field of the selected
playlist entry.
1/3
No.
Title
001 JAN/02/2009 13:47
002 JAN/02/2009 13:51
003 JAN/02/2009 14:08
Sort
Length
00:06:09
00:03:33
00:01:54
Title List
a Check
eExit
Rename
HDD
Dolphin
Back Space
m MOVE
Space
sSELECT
Clear
rRETURN
Save
eEXIT
English _93
● Editing
Follow these instructions to play the playlist entries.
editing
Editing a Scene for the Playlist
SXC
(VR mode)
Follow these instructions to edit scenes for a playlist.
N Using the PLAY LIST button
1. With the unit in Stop mode/Playback mode, press the PLAY LIST
button.
Playlist
HDD
JAN/02/2009 13:47
. Press the ▲▼ buttons to select the title you want to edit from the
Playlist, then press the RED(A) button.
The Edit menu is displayed.
1/3
No.
Title
001 JAN/02/2009 13:47
002 JAN/02/2009 13:51
003 JAN/02/2009 14:08
Delete
Copy
Rename
� PLAYLIST
Edit
Playlist
4 JAN/02/2009 13:47
New
Playlist
� 6 Scenes
Select All
. Press the ▲▼ buttons to select Edit Playlist, then press the OK
or + button.
The Edit Playlist screen is displayed.
Edit
Sort
Length
00:06:09
00:03:33
00:01:54
Title List
a Check
eExit
Edit Playlist
HDD
JAN/02/2009 13:47
Scene No. 1/6
01 00:02:24
02 00:00:34
03 00:00:31
05 00:00:09
06 00:01:06
07 00:00:00
Modify
Move
04 00:01:22
Add
Delete
sPLAY
eExit
Playing a Selected Scene
. Press the ▲▼_ + buttons to select the scene you want to play, then press the OK or PLAY (
The selected scene is played.
~ To stop scene play, press the STOP ( ) button.
) button.
Modifying a Scene (Replacing a Scene)
To setup, follow steps 1 to 3.
4-1. Press the ▲▼_ + buttons to select the scene you want to Modify, then press the RED(A) button.
The Modify Scene screen is displayed.
5. Press the OK button at the start point of the scene.
~ The image and starting point time is displayed on the Start
window.
~ Select the starting or ending point of the section you want to
modify using the playback related buttons (PLAY ( ),
PAUSE ( ), SEARCH (
), SKIP (
)).
Scene No. 001
Start
Title List 1/3
94_ editing
End
00:04:54
►
End
Start
Change
# Pause
+ Play
6. Press the OK button at the end point of the scene.
~ The image and ending point time is displayed in the End
window.
7. Press the _ + buttons to select Change, then press the OK button.
~ The scene you want to modify is changed with the selected
section.
Modify Scene
HDD
JAN/02/2009 13:47
< MOVE
( ) SCAN
sSELECT
00:06:25
00:05:27
Return
[ ] SKIP
rRETURN
eEXIT
Modify Scene
HDD
JAN/02/2009 13:47
Scene No. 001
Start
Title List 1/3
00:04:54
#
Start
+ Play
< MOVE
End
Change
# Pause
( ) SCAN
sSELECT
rRETURN
End
00:06:25
00:05:27
Return
[ ] SKIP
eEXIT
Moving a Scene (Changing the Position of a Scene)
To setup, follow steps 1 to 3 in page 94.
Edit Playlist
HDD
JAN/02/2009 13:47
5. Press the ▲▼_ + buttons to select the position to which you want to move the selected scene, then select the OK button.
01 00:02:24
02 00:00:34
03 00:00:31
05 00:00:09
06 00:01:06
07 00:00:00
M
Scene No. 1/6
04 00:01:22
sSAVE
eExit
` You cannot move the selected scene to the position of the next
scene, because the selected scene should be inserted before that position, which requires no action.
` Depending on the kind of disc, the displayed screen may have a slight difference.
Adding a Scene
To setup, follow steps 1 to 3 in page 94.
4-1. Press the ▲▼_ + buttons to select the scene that will have a new scene inserted before it, then press the YELLOW(C) button. The Add Scene screen is displayed.
5. Press the OK button at the starting point of the scene.
~ The image and starting point time is displayed on the Start
window.
~ Select the starting or ending point of the section you want to
modify using the playback related buttons (PLAY ( ),
PAUSE ( ), SEARCH (
), SKIP (
)).
Add Scene
HDD
JAN/02/2009 13:47
Scene No. 001
Start
Title List 1/3
End
00:01:51
+
End
Start
+ Play
6. Press the OK button at the end point of the scene.
~ The image and end point time are displayed in the End window.
~ To cancel, press the _ + buttons to select Return, then press
the OK button.
Add
# Pause
< MOVE
( ) SCAN
sSELECT
00:00:00
00:01:51
Return
[ ] SKIP
rRETURN
eEXIT
Add Scene
HDD
JAN/02/2009 13:47
Scene No. 001
Start
7. Press the _ + buttons to select Add, then press the OK button.
~ The section you want to add is inserted prior to the scene
selected in step 4-1 of Adding a Scene.
Title List 1/3
End
00:01:51
#
Start
+ Play
End
Add
# Pause
< MOVE
( ) SCAN
sSELECT
rRETURN
00:07:28
00:07:28
Return
[ ] SKIP
eEXIT
Deleting a Scene
To setup, follow steps 1 to 3 in page 94.
4-1. Press the ▲▼_ + buttons to select the scene you want to
delete, then press the BLUE(D) button.
~ The message “Do you want to delete the scene?” is displayed.
Edit Playlist
HDD
JAN/02/2009 13:47
5. Press the _ + buttons to select Yes, then press the OK to delete the selected scene.
01 00:02:24
Scene No. 1/6
02
03
Do you want to delete the scene?
Yes
05 00:00:09
Modify
< MOVE
06 00:01:06
Move
sSELECT
04 00:01:22
No
07 00:00:00
Add
rRETURN
Delete
eEXIT
English _95
● Editing
4-1. Press the ▲▼_ + buttons to select the scene you want to move (change the position), then press the GREEN(B) button.
~ A yellow selection window is displayed on the scene to be
moved.
editing
Deleting a Playlist Entry from the Playlist
N Using the PLAY LIST button
1. With the unit in Stop mode/Playback mode, press the
PLAY LIST button.
1/3
No.
Title
001 JAN/02/2009 13:47
002 JAN/02/2009 13:51
003 JAN/02/2009 14:08
. Press the ▲▼ buttons to select an entry you want to delete in
the Playlist, then press the MARKER button until a checkmark
appears. Repeat this step to select an additional title you want to
delete.
~ If you don’t want to delete a certain one of the checked entries,
simply select that entry and press the MARKER to deselect it
until a checkmark disappears.
Length
00:06:09
00:03:33
00:01:54
� PLAYLIST
4 JAN/02/2009 13:47
� 6 Scenes
Edit
. Press the RED(A) button to select Edit.
Edit menu is displayed.
Sort
Title List
a Check
eExit
Playlist
HDD
JAN/02/2009 13:51
. Press the ▲▼ buttons to select Delete, then press the OK or +
button.
~ You will be prompted with the delete confirmation message “Do
you want to delete?”.
2/3
No.
Title
001 JAN/02/2009 13:47
002 JAN/02/2009 13:51
003 JAN/02/2009 14:08
Delete
Copy
� PLAYLIST
New
Playlist 13:47
4 JAN/02/2009
Select
All
� 6 Scenes
Unselect All
Edit
. Press the _ + buttons to select Yes, then press the OK button.
You will be automatically returned to the Playlist screen after the
delete operation has finished.
M
Playlist
HDD
JAN/02/2009 13:47
Sort
Title List
a Check
Length
00:06:09
00:03:33
00:01:54
eExit
Playlist
HDD
JAN/02/2009 13:51
` If you select “Select All” in the Edit menu, all title will be checked.
2/3
No.
Title
001 JAN/02/2009 13:47
002 JAN/02/2009 13:51
2 items
selected 14:08
003areJAN/02/2009
Do you want to delete?
� PLAYLIST
4 JAN/02/2009 13:47
Yes
� 6 Scenes
Edit
Sort
< MOVE
sSELECT
Length
00:06:09
00:03:33
00:01:54
No
Title List
rRETURN
eEXIT
Using the Sort (Playlist)
When you need to change the Sort order of Playlist, you can change it simply.
1. While the list menu is displayed, press the GREEN(B) button to
select Sort.
. Press the ▲▼ buttons to select the desired item, then press the
OK or + button.
~ Date : In order of when the playlists were created
~ Name : In alphabetical order
M
` You can sort by Date, Name. Sorted list will be resorted in copied
96_ editing
order upon re-entering Playlist.
Playlist
HDD
JAN/02/2009 13:47
1/3
No.
Title
001 JAN/02/2009 13:47
002 JAN/02/2009 13:51
003 JAN/02/2009 14:08
Length
00:06:09
00:03:33
00:01:54
� PLAYLIST
4 JAN/02/2009 13:47
� 6 Scenes
Edit
Date
Name
Sort
Title List
a Check
eExit
Copying from Hdd to Dvd Or Vice-versa
About the Copy Screen
● Editing
Total size and number of selected titles for copying
Title to be copied
Copy
HDD
Selected Items :
This shows available disc space
Avallable : 4099MB
Source : HDD
To : DVD
001 JAN/01/2009 1
002 JAN/01/2009 1
003 JAN/01/2009 1
The location where the copied files are stored
; DVD
Copy start button
3MPEG2
0 SP
�36.5MB
Start Copy Sort Selection
a Check
Sort button (Date, Name, Length, Channel Info)
eExit
Selection button
7
- Select All : All entries in the current folder will be
checked.
- Unselect All : All checked entries will be unchecked.
Contents Copy Specifications
Contents
HDD  DVD
DVD  HDD
Recorded Video Title
Supported
Supported
Copy Protected Title
Not supported
Not supported
Copy Once Title
Move
(Deletes the Title in the HDD after copying)
Not supported
The Copy is possible only with CPRM-Compatible disc.
Once “Copy Once programme” has been recorded on the DVD disc, this title cannot be copied to HDD
anymore.
But “Copy Once programme” has been recorded on the HDD, this title can be copied to DVD-RW(VR mode)
or DVD-RAM.
N Using the TITLE LIST button
1. Press the OPEN/CLOSE button and place a recordable disc on
the disc tray.
1/3
No.
Title
001 JAN/01/2009 17:30 PR
002 JAN/02/2009 21:00 PR
003 JAN/03/2009 23:15 PR
. Press the OPEN/CLOSE button to close the disc tray. Wait until
LOAD disappears from the front panel display. Check that the
disc has enough available space for the recording.
. Select a desired mode by pressing the HDD or DVD button on
the remote control.
You can also select a desired mode by pressing the HDD/DVD
button on the front panel.
Title List
HDD
JAN/01/2009 17:30 PR1
Length
01:00:00
01:00:00
00:30:00
3 MPEG2
4 JAN/01/2009 17:30
1 SP
V-Mode Compatibility
Edit
Sort
Go to
Contents
a Check
eExit
. With the unit in Stop mode/Playback mode, press the TITLE LIST button.
English _97
editing
. Press the RED(A) button, then press the $% button to select
Copy.
Press the OK button. Copy screen is displayed.
. Press the $% buttons to select the title you wan to copy, then
press the MARKER button until a checkmark appears.
Repeat this step to select an additional title you want to copy.
~ If you don’t want to copy a certain one of the checked entries,
simply select that entry and press MARKER button to deselect
it until a checkmark disappears.
Copy
HDD
Selected Items :
Avallable : 4099MB
Source : HDD
To : DVD
001 JAN/01/2009 1
002 JAN/01/2009 1
003 JAN/01/2009 1
; DVD
3MPEG2
0 SP
�36.5MB
Start Copy . Press the RED(A) button to select Start Copy.
~ The title to be copied is not displayed on the screen, and
copying begins while the currently broadcasting programme is
displayed on the screen.
~ Press the INFO button to change the copy processing bar.
If you press INFO button again, copy processing bar will be
appeared.
~ To cancel the copying in progress, press the RED(A) button.
Sort Selection
a Check
eExit
21%

Cancel
b Bar Type
c Channel
. After a successful copy, “The title is successfully copied” message is displayed.
M
` The noise may be occurred when copying because HDD & DVD Recorder supports high speed copying.
DVD-Video Copy
1. Press the OPEN/CLOSE button and place a DVD-Video disc on
the disc tray.
. Press the OPEN/CLOSE button to close the disc tray.
. During the playback, press the COPY button.
Copy will be started.
M
DVD ➝ HDD
● Copying
` The Copy function will be disabled in the followings:
- If you try to copy in the section of a menu.
- NTSC disc or copy-protected disc
- Titles that are different in the broadcasting system
- The audio title that is copied to the HDD will be recorded in the 2ch AC3 format.
- For the audio output in DTS mode, the audio source will not be copied.
Copying MP3, JPEG or DivX
Contents Copy Specifications
~
~
~
~
~
Contents
HDD  DVD or USB
DVD  HDD or USB
USB  HDD or DVD
MP3
Supported
Supported
Supported
JPEG(photo)
Supported
Supported
Supported
DivX
Supported
Supported
Supported
CD-DA
Not supported
Supported
Not supported
Disc(CD-DA/CD-R/CD-RW/DVD-RAM/DVD±R(Finalise)/DVD+RW/DVD-RW(Finalise))  HDD or USB
HDD  DVD-R, DVD-RW(V) or USB
USB  HDD or DVD-R, DVD-RW(V)
PTP USB is not available when you copy to USB.
If the disc is finalised through Disc Manager, it can be compatible with PC as a disc with a UDF file system.
98_ editing
File Copy
1. Insert a JPEG disc, MP3 disc or DivX disc into the disc tray.
CD
Source : DVD
. Press the ▲▼ buttons to select Library, then press the OK or +
button.
. Press the ▲▼ buttons to select Music, Photo or DivX, then
press the OK or + button.
. Press the RED(A) button, then press the $% button to select
Copy.
Press the OK button. Copy screen is displayed.
. Press the ▲▼ buttons to select the MP3, Photo or DivX file you
want to copy, then press the MARKER button until a checkmark
appears.
~ If you don’t want to copy a certain one of the checked entries,
simply select that entry and press MARKER button to deselect
it until a checkmark disappears.
. Press the + button, then press the OK button to make the first
folder where the copied files are stored.
~ You can create a new folder by pressing the GREEN(B) button.
Available :
To :
Y ROOT
001 SONG 1.mp3
002 SONG 2.mp3
003 SONG 3.mp3
004 SONG 4.mp3
005 SONG 5.mp3
�MP3
�5.85MB
Start Copy Sort [/] Previous/Next Day
E HDD
E USB
Selection All
Unselect All
a Check
eExit
CD
Copy
Selected Items: 9.68MB (2)
Available : 236724MB
Source : DVD
To : HDD
Y ROOT
001 SONG 1.mp3
002 SONG 2.mp3
003 SONG 3.mp3
004 SONG 4.mp3
005 SONG 5.mp3
�MP3
�3.84MB
Start Copy ; ROOT
New Folder eExit
CD
Copy
Selected Items: 9.68MB (2)
Available : 236724MB
Source : DVD
. Press the RED(A) button to select Start Copy.
~ The message “Number of file : x” is displayed.
. Press the _ + buttons to select Start, then press the OK button.
File copy begins.
~ To cancel the copying in progress, press the EXIT ( ) button.
Copy
Selected Items: 5.85MB (1)
To : HDD
Y ROOT
001 SONG 10.mp3
Number of file : 2
002 SONG 1.mp3
003 SONG 2.mp3
004 Start
SONG 3.mp3 EXIT
�MP3
�3.84MB
; ROOT
005 SONG 5.mp3
Start Copy New Folder
eExit
CD
Copy
Selected Items: 9.68MB (2)
Available : 236724MB
Source : DVD
To : HDD
Copying...
;
Y ROOT
; ROOT
Free space
23662310.mp3
MB
001: SONG
Number of file : 2 / 8
002
SONG1.mp3
1.mp3
File Name
: Song
003 SONG 2.mp3
�MP3
33%
004 SONG 3.mp3
�3.84MB
005 SONG 5.mp3
Start Copy New Folder eExit
Folder Copy
1. Insert a Disc (JPEG, MP3 or DivX) into the tray.
. Press the ▲▼ buttons to select Library, then press the OK or +
button.
CD
Copy
Selected Items: 33.7MB (2)
Source : DVD
. Press the ▲▼ buttons to select Music, Photo or DivX then
press the OK or + button.
MP3, JPEG or DivX folder is displayed.
To :
Y ROOT
E MP3 (1)
E MP3 (2)
E MP3 (3)
�MP3
�40.2MB
Start Copy Available :
Sort E HDD
E USB
Selection All
Unselect All
a Check
eExit
English _99
● Editing
. Press the OPEN/CLOSE button to close the disc tray. Wait until
LOAD disappears from the front panel display. Check that the
disc has enough available space for the recording.
editing
. Press the RED(A) button, then press the $% button to select
Copy.
Press the OK button. Copy screen is displayed.
. Press the ▲▼ buttons to select the folder you want to copy, then
press the MARKER button until a checkmark appears.
~ If you don’t want to copy a certain one of the checked folders,
simply select that entry and press MARKER button to deselect
it until a checkmark disappears.
. Press the +$▼ or OK button to select the location where the
copied files are stored.
~ You can create a new folder by pressing the GREEN(B) button.
CD
Available : 236715MB
Source : DVD
To : HDD
Y ROOT
E MP3 (1)
E MP3 (2)
E MP3 (3)
�MP3
�36.6MB
Start Copy ; ROOT
New Folder eExit
CD
Copy
Selected Items: 76.8MB (2)
Available : 236715MB
Source : DVD
. Press the RED(A) button to select Start Copy.
The message “Number of file : x” is displayed.
~ The item is named the number of file that is available in the
folder.
. Press the _ + buttons to select Start, then press the OK button.
Folder copy begins.
Subfolders and files in the selected folder are copied.
~ To cancel the copying in progress, press the EXIT ( ) button.
Copy
Selected Items: 76.8MB (2)
To : HDD
Y ROOT
001 SONG 10.mp3
Number of file : 2
002 SONG 1.mp3
003 SONG 2.mp3
004 Start
SONG 3.mp3 EXIT
�MP3
�3.84MB
; ROOT
005 SONG 5.mp3
Start Copy New Folder eExit
CD
Copy
Selected Items: 76.8MB (2)
Available : 236715MB
Source : DVD
To : HDD
Copying...
;
Y ROOT
; ROOT
Free space
:
236615
MB
001 SONG 10.mp3
Number of file : 2 / 8
002
SONG
1.mp3
File Name : 01. ### ## 1.mp3
003 SONG 2.mp3
�MP3
33%
004 SONG 3.mp3
�3.84MB
005 SONG 5.mp3
Start Copy M
` Pressing the EXIT (
New Folder eExit
) button during folder copying will cancel the folder copying after the current file is copied.
` You can copy up to 500 including files and sub folders to one folder. [ MP3, JPEG, DivX ]
` If you want to file copy, you should create a new folder before starting a copy.
You cannot copy to top-level(ROOT) folder directly without creating a new folder.
` If the top-level (ROOT) folder has had already 500 including folders, you should delete one or more items before you
can create a new folder.
` File size on a disc and the copied file in the HDD may be slightly different due to the file system.
` If you check some entries in the current folder and move to open a different folder, those entries are automatically
unchecked and excluded from the selection list.
Changing the name of Music/Photo/DivX file
S
You can rename a Music, Photo or DivX file copied to HDD.
1. Press the ▲▼ buttons to select the entry you want to rename,
then press the RED(A) button.
Music List
HDD
SONG 1.mp3
No.
Y
001
002
003
004
005
006
Copy
New Playlist
@ + # 00:02:22
Go To Playlist
9 SONG 10.mp3
Select All
E ROOT
Delete
Rename
Edit
Sort
[/] Previous/Next Day
100_ editing
Title
ROOT
SONG 1.MP3
SONG 2.MP3
SONG 3.MP3
SONG 4.MP3
SONG 5.MP3
SONG 6.MP3
Size
3.8 MB
3.8 MB
5.1 MB
9.2 MB
5.2 MB
10.3 MB
Play Mode
Contents
a Check
eExit
. Press the ▲▼ buttons to select Rename, then press the OK or
+ button.
Rename Screen is displayed.
Dream
Back Space
m MOVE
Space
sSELECT
Clear
Save
rRETURN
eEXIT
Music List
HDD
Dream.mp3
1/9
No.
Y
. Press the BLUE(D) button to select Save.
The changed file name is displayed on the selected entry.
Q
002
003
004
005
006
@ + # 00:00:00
9 Dream.mp3
E ROOT
Edit
Title
ROOT
Dream.mp3
SONG 2.MP3
SONG 3.MP3
SONG 4.MP3
SONG 5.MP3
SONG 6.MP3
Sort
[/] Previous/Next Day
Size
3.8 MB
3.8 MB
5.1 MB
9.2 MB
5.2 MB
10.3 MB
Play Mode
Contents
a Check
eExit
Disc Manager
Editing the Disc Name
XCVKL
Follow these instructions to give a name to a disc.
1. With the unit in Stop mode, press the MENU button.
DVD-RAM(VR)
. Press the ▲▼ buttons to select Disc Manager, then press the
OK or + button.
. Press the _ + buttons to select Rename, then press the OK button.
The Rename screen is displayed.
. Select the desired characters using the ▲▼_ + buttons, then
press the OK button.
. Press the BLUE(D) button to select Save.
A disc name is given to the disc.
Disc Name
Used Space
00:17
Available Space
01:54 SP ( 3.85 GB)
Disc Protection Info
Not Protected
Current Rec. Mode
VR-Mode
Rename
Disc Manager
< MOVE
Protection
sSELECT
( 0.52 GB)
Delete All
rRETURN
DVD-RAM(VR)
M
Format
eEXIT
Rename
` You may need to clear Disc Protection beginning editing.
DISC–1
` Depending on the kind of disc, the displayed screen may be different.
` If you have recorded a DVB-T radio channel program, the time
information displayed for each of free and used space may be incorrect.
Back Space
m MOVE
Space
sSELECT
Clear
Save
rRETURN
eEXIT
English _101
● Editing
. Select the desired characters using the ▲▼_ + buttons, then
press the OK button.
~ Back Space (RED(A) button) : Deletes and moves the cursor
backwards by one position.
~ Space (GREEN(B) button) : Enters a blank and moves the
cursor one forward (to the right).
~ Clear (YELLOW(C) button) : Deletes all the character inputs.
~ Save (BLUE(D) button) : Registers the character inputs.
Rename
HDD
editing
Disc Protection
XCV
Disc Protection allows you to protect your discs from being formatted or deleted due to unintended
operations.
1. With the unit in Stop mode, press the MENU button.
DVD-RAM(VR)
. Press the ▲▼ buttons to select Disc Manager, then press the
OK or + button.
. Press the _ + buttons to select Protection, then press the OK
button.
. Press the _ + buttons to select On, then press the OK button.
Disc Name
Used Space
00:17
Available Space
01:54 SP ( 3.85 GB)
Disc Protection Info
Not Protected
Current Rec. Mode
VR-Mode
Rename
Disc Manager
Protection
< MOVE
( 0.52 GB)
Delete All
sSELECT
rRETURN
DVD-RAM(VR)
eEXIT
Disc Manager
Disc Name
Used Space
00:17
Available Space
Current Rec. Mode
Rename
Not Protected
On
VR-Mode
Off
Protection
< MOVE
( 0.52 GB)
01:54 SP ( 3.85 GB)
Disc Protection:
Disc Protection Info
Format
Delete All
sSELECT
rRETURN
Format
eEXIT
Delete All Title Lists
XCVKL
1. With the unit in Stop mode, press the MENU button.
DVD-RAM(VR)
. Press the ▲▼ buttons to select Disc Manager, then press the
OK or + button.
. Press the _ + buttons to select Delete All, then press the OK
button.
~ You will be prompted with the confirmation message “Do you
want to delete all title lists?”.
~ When Protected Entry exists: The Delete All Title List function
will not operate. If there is a title containing a still picture,
however, that function will not operate.
If you want to delete a protected entry, disable Protect for it on
the Lock item.
~ When protected a DVD-RAM/-RW is used, data cannot be
deleted from a disc.
~ If you select Yes, you will be prompted with the confirmation
message “All playlists will also be deleted. Do you want to
continue?”.
. Press the _ + buttons to select Yes, then press the OK button.
All title lists are deleted.
102_ editing
Disc Name
Used Space
00:17
Available Space
01:54 SP ( 3.85 GB)
Disc Protection Info
Not Protected
Current Rec. Mode
VR-Mode
Rename
Disc Manager
Protection
< MOVE
( 0.52 GB)
Delete All
sSELECT
rRETURN
DVD-RAM(VR)
Format
eEXIT
Disc Manager
Disc Name
Used Space
00:17
Available Space
( 0.52 GB)
01:54 SP ( 3.85 GB)
Do you want to delete all title lists?
Disc Protection Info
Current Rec. Mode
Rename
< MOVE
Not Protected
Yes
Protection
sSELECT
VR-Mode
No
Delete All
rRETURN
Format
eEXIT
Delete All Title Lists/DivX Lists /Music Lists/Photo Lists
S
1. With the unit in Stop mode, press the MENU button.
HDD
Disc Manager
Used Space
000:39
Available Space
065:19 XP ( 231.01 GB)
● Editing
. Press the ▲▼ buttons to select Disc Manager, then press the
OK or + button.
( 1.68 GB)
. Press the _ + buttons to select Delete, then press the OK
button.
. Press the _ + buttons to select the Title, DivX, Music or Photo,
then press the OK button.
. Press the _ + buttons to select Yes, then press the OK button.
All title lists, DivX lists, music lists or photo lists are deleted.
Delete
< MOVE
sSELECT
Format
rRETURN
HDD
eEXIT
Disc Manager
Used Space
000:39
Available Space
065:19 XP ( 231.01 GB)
( 1.68 GB)
Select contents to delete all
DivX
Title
Music
Photo
Delete
< MOVE
sSELECT
Format
rRETURN
HDD
eEXIT
Disc Manager
Used Space
000:39
Available Space
( 1.68 GB)
065:19 XP ( 231.01 GB)
All playlists will also be deleted.
Do you want to continue?
Yes
No
Delete
< MOVE
sSELECT
Format
rRETURN
eEXIT
Formatting a Disc
SXCK
Use these instructions to format a disc.
The disc protect should also be cleared.
HDD
1. With the unit in Stop mode, press the MENU button.
. Press the ▲▼ buttons to select Disc Manager, then press the
OK or + button.
. Press the _ + buttons to select Format, then press the OK
button.
HDD/DVD-RAM/+RW
~ You will be prompted with the confirmation message “Current
media : ✳✳✳ Do you want to format?”.
~ If you select Yes, you will be prompted with the confirmation
message “All data will be deleted. Do you want to continue?”.
Disc Manager
Used Space
000:39
Available Space
065:19 XP ( 231.01 GB)
( 1.68 GB)
Delete
< MOVE
sSELECT
Format
rRETURN
HDD
eEXIT
Disc Manager
Used Space
000:39
Available Space
065:19 XP ( 231.01 GB)
( 1.68 GB)
Current media: HDD
Do you want to format?
Yes
No
Delete
< MOVE
sSELECT
rRETURN
Format
eEXIT
English _103
editing
DVD-RW
~ You will be prompted with the confirmation message “Choose
the recording format for DVD-RW.”
~ If you select the desired format type, you will be prompted with
the confirmation message “All data will be deleted. Do you want
to continue?”.
. Press the _ + buttons to select Yes, then press the OK button.
The disc is formatted.
DVD-RW(VR)
Disc Manager
Disc Name
Used Space
00:17
Available Space
01:54 SP ( 3.85 GB)
Disc Protection Info
Not Protected
Current Rec. Mode DVD-VR
VR-Mode
DVD-V
( 0.52 GB)
Choose the recording format for DVD-RW.
Rename
Protection
< MOVE
Delete All
Finalise
sSELECT
rRETURN
Format
eEXIT
DVD-VR and DVD-V are defined according to their recording format.
DISC
DVD-VR
DVD-V
DVD-RAM/-RW
DVD-RW/DVD-R
~ With DVD+RW discs, there is no difference between DVD-Video format (Video mode) and DVD-Video
Recording format (VR mode).
Finalising a Disc
CVL
After you record titles onto a DVD-RW/±R disc with your HDD & DVD Recorder, it needs to be finalised before
it can be played back on external devices.
1. With the unit in Stop mode, press the MENU button.
DVD-RW(VR)
. Press the ▲▼ buttons to select Disc Manager, then press the
OK or + button.
. Press the ▲▼_ + buttons to select Finalise, then press the OK
button. You will be prompted with the message “Do you want to
finalise disc?”.
. Press the _ + buttons to select Yes, then press the OK button.
You will be prompted again with the message “Disc will be
finalised. Do you want to continue?”.
Disc Name
Used Space
00:17
Available Space
01:54 SP ( 3.85 GB)
Disc Protection Info
Not Protected
Current Rec. Mode
VR-Mode
Protection
m MOVE
rRETURN
00:17
Not Protected
Yes
Rename
< MOVE
( 0.52 GB)
01:54 SP ( 3.85 GB)
Do you want to finalise disc?
Current Rec. Mode
VR-Mode
No
Delete All
Finalise
sSELECT
rRETURN
DVD-RW(VR)
` Finalising time may be different depending on the amount of data
recorded on the disc.
00:17
Available Space
Current Rec. Mode
Not Protected
Yes
Rename
(See page 50)
Protection
< MOVE
( 0.52 GB)
01:54 SP ( 3.85 GB)
Disc will be finalised.
Do you want to continue?
Disc Protection Info
` You can finalise the disc automatically using EZ Record.
eEXIT
Used Space
finalisation process.
Format
Disc Manager
Disc Name
` Data on the disc will be damaged if the recorder is powered off during
eEXIT
Disc Protection Info
Protection
Format
Disc Manager
Used Space
` After being finalised, the DVD±R/-RW(video mode) operates in the
104_ editing
Finalise
Disc Name
` Once a disc is finalised, you cannot delete entries from the record list.
` Depending on the disc type, the displayed screen may be different.
Delete All
sSELECT
DVD-RW(VR)
Available Space
same manner as a DVD-Video.
( 0.52 GB)
Rename
. Press the _ + buttons to select Yes, then press the OK button.
The disc is finalised.
M
Disc Manager
VR-Mode
No
Delete All
Finalise
sSELECT
rRETURN
Format
eEXIT
Unfinalising a Disc (V/VR mode)
C
1. With the unit in Stop mode, press the MENU button.
DVD-RW(VR:F)
Disc Name
Current Rec. Mode
VR-Mode
. Press the _ + buttons to select Unfinalise, then press the OK
button.
You will be prompted with the message “Do you want to
unfinalise disc?”.
. Press the _ + buttons to select Yes, then press the OK button.
You will be prompted again with the message “Disc will be
unfinalised. Do you want to continue?”.
● Editing
. Press the ▲▼ buttons to select Disc Manager, then press the
OK or + button.
Disc Manager
Unfinalise
< MOVE
sSELECT
rRETURN
DVD-RW(VR:F)
. Press the _ + buttons to select Yes, then press the OK button.
The disc is unfinalised.
Format
eEXIT
Disc Manager
Disc Name
Current Rec. Mode
VR-Mode
Do you want to unfinalise disc?
Yes
No
Unfinalise
< MOVE
sSELECT
rRETURN
DVD-RW(VR:F)
Format
eEXIT
Disc Manager
Disc Name
Current Rec. Mode
VR-Mode
Disc will be unfinalised.
Do you want to continue?
Yes
No
Unfinalise
M
< MOVE
sSELECT
rRETURN
Format
eEXIT
` A DVD-RW can be finalised or unfinalised in Video mode.
Finalise
Unfinalise
Mark
DVD-Video(RW)
DVD-RW(V)
Operation
Same as DVD-Video
Additional recording, protection and deletion
are possible.
` A DVD-RW can be finalised or unfinalised in VR mode.
Finalise
Unfinalise
Mark
DVD-RW(VR:F)
DVD-RW(VR)
Operation
Additional recording, deletion, editing, and
protection are impossible.
Additional recording, deletion, editing, and
protection are possible.
English _105
reference
Troubleshooting
If your product malfunctions, go through the checkpoints below before contacting a Samsung authorised service
centre.
PROBLEM
EXPLANATION/SOLUTION
The input is displayed for a while
when the power is turned on.
The HDD & DVD Recorder requires some time to initialise and the input will be
displayed for approx. 10 seconds after it is turned on.
Cannot record TV programmes.
• Check whether the power cord is securely plugged into the power outlet.
• Did you set the HDD & DVD Recorder channel settings correctly?
• Check the free space on your HDD/DVD-RAM/±RW/±R discs.
I pressed the REC button but there is
no response.
Check available disc type. (See page 71)
If a programme is copy protected, it cannot be recorded.
Cannot play the disc.
• Check whether the disc is inserted correctly with the label facing up.
• Check the regional code of the DVD disc.
• This HDD & DVD Recorder cannot play some types of discs. (See pages 8, 55)
icon appears on the screen.
You cannot use this operation or function due to one of the following reasons:
(1) Your DVD disc restricts it.
(2) Your DVD disc does not support this feature (for example: angles)
(3) The feature is not available at the moment.
(4) You’ve requested a title, chapter, or scan time that is out of range.
Play mode settings are different from
the settings configured in the
Settings menu.
The disc does not support all selected functions.
In this case, some settings configured in the settings menu may not work properly.
Cannot change the aspect ratio.
The aspect ratio is fixed for DVD discs. (See page 45)
The angle operation does not work
while playing a DVD disc.
The angle operation is available only when the disc contains images captured from
diff erent angles.
The selected audio and/or subtitle
language is not played.
Audio and subtitle languages are disc-specific. Only the sound and subtitle languages
contained on the DVD disc are available and displayed in the disc menu.
Cannot copy title or file to the other
mode.
• DVD discs encoded with copy protection can not be copied to HDD.
• Refer to “Contents Copy Specifications” on page 6 to check if copying is supported.
• Refer to “V-Mode Compatibility” on page 50 to check if copying is support.
The disc revolves, but no image or
bad quality images is displayed.
• Be sure that the Video Setting is properly set. (See pages 45~46)
• Check whether there is damage to or any foreign material on your disc.
• Some low quality discs may not play properly.
• If scenes change from dark to bright suddenly, the screen may shake vertically
temporarily, but this is not a fault.
106_ reference
PROBLEM
EXPLANATION/SOLUTION
• Are you watching a programme in slow or skip mode?
If you are playing a programme at a speed other than normal speed, sound will not
be heard. (Except for forward search (X 2) in disc.)
• Check the connections and settings. (See pages 28~33, 44~45)
• Check whether the disc is damaged. Clean the disc, if necessary.
• Check whether the disc is inserted correctly with the label facing up.
No audio output.
Check whether you have selected the correct digital output options in the Audio
Output Options menu. (See pages 44~45)
Timer lamp flickers.
• Check there is enough space in the disc or HDD for recording.
• Check whether the current disc is recordable or not.
Make sure to check before the start time of recording.
Timer recording does not work
properly.
• Re-check the recording time and the end time settings again.
• Recording will be cancelled if the power is interrupted due to a power failure or
another similar reason while recording.
Cannot copy into USB or vice-versa
• Check the USB connection. Disconnect and try to connect again.
• Refer to “Compatible USB devices at host port” on pages 8, 34.
No HDMI output.
• Check the Video output is HDMI enabled.
• Check the connection between the TV and the HDMI jack of the HDD & DVD
Recorder.
• See if your TV supports HDMI.
Abnormal HDMI output screen.
If snow noise appears on the screen, it means that TV does not support HDCP
(High bandwidth Digital Content Protection).
HDMI output Jitter.
• Check your TV system setup correctly.
• Please refer to the user’s manual of your TV.
The remote control doesn’t work.
• Point the remote control at the remote control sensor on your HDD & DVD Recorder.
Allow for proper distance. Remove obstacles between your HDD & DVD Recorder
and the remote control.
• Check whether the batteries are drained.
• Check the TV/DVD selection button setting.
• Check whether TV, DVD or HDD control button is selected or not.
I forgot my password for parental
supervision.
Press and hold the Play/Pause (❯II) buttons on the front panel for more than 10
seconds with no disc in the unit. All settings including the password will revert to the
factory settings. Do not use this unless absolutely necessary.
Is it possible to change a subtitle
and an audio signal on a recorded
disc?
A recorded disc is played with only the subtitle and the audio signal which were
selected during recording.
Other problems.
• Read the table of contents and then find and read the section describing your
problem, follow the instructions given.
• Plug your HDD & DVD Recorder off and on.
• If the problem still persists, contact a nearby Samsung service centre.
English _107
● Reference
No sound.
appendix
Specifications
General
Input
Power requirements
220-240 V AC, 50 Hz
Power consumption
28 Watts / 1 Watts (Power off )
Weight
3.6 Kg
Dimensions
430 mm(W) x 300 mm(D) x 55 mm(H)
Operating temp.
+5 °C to +35 °C
Other conditions
Keep level when operating. Less than 75% operating humidity
Video
Composite Video : 1.0 V p-p at 75Ω load, sync negative
Audio
Max.Audio Input Level : 2 Vrms
DV Input
IEEE 1394(4p) compatible jack
Receivable Channels
Scart Jack
PAL-B/G, D/K, I, DVB-T
AV2 (Scart Ext)
Video : Composite, RGB, Audio: analogue
Analogue output jacks x 1
Audio
Optical digital audio output
Composite Video : Video output jack x 1
Output
Video
Component output x 1 (Y : 1,0Vp-p, PB : 0,70Vp-p, PR : 0,70Vp-p at 75Ω load)
HDMI/DVI (576p, 720p,1080i, 1080p)
Scart Jack
Recording
HDD Capacity
USB
AV1 (Scart TV)
Video : Composite, RGB, Audio: analogue
Picture Compression format
MPEG-II
Audio Compression format
Dolby Digital 2ch/256Kbps, MPEG-II
Recording Quality
XP (about 8,5 Mbps), SP (about 4,5 Mbps), LP (about 2,5 Mbps),
EP (about 1,6 Mbps or about 1,2 Mbps)
Audio Frequency Response
20 Hz~20 kHz
DVD-SH893
160 GB
DVD-SH895
250 GB
DVD-SH897
320 GB
USB 2.0 H/S
Host x 1
Audio Output
For DVD discs, audio signals recorded at 96 kHz sampling frequency are converted into and output at 48 kHz.
Disc Type
DVD
AUDIO CD (CD-DA)
Analogue Audio Output
48 / 96 kHz
44,1 kHz
Digital Audio Output
48 kHz
44,1 kHz
108_ appendix
 This product uses parts of the software from the Independent JPEG Group.
 This product uses some software programs which are distributed under the GPL/LGPL license. Accordingly, the following GPL and LGPL software source codes that
have been used in this product can be provided after asking to vdswmanager@samsung.com. GPL software: Linux Kernel, Busybox, Binutilis LGPL software: Glibc
The GNU General Public License (GPL)
Version 2, June 1991
Copyright (C) 1989, 1991
Free Software Foundation, Inc.59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
Everyone is permitted to copy and distribute verbatim copiesof this license document, but changing it is not allowed.
Preamble
The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public License
is intended to guarantee your freedom to share and change free software--to make sure the software is free for all its users. This General Public
License applies to most of the Free Software Foundation’s software and to any other program whose authors commit to using it. (Some other Free
Software Foundation software is covered by the GNU Library General Public License instead.) You can apply it to your programs, too.
When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the
freedom to distribute copies of free software (and charge for this service if you wish), that you receive source code or can get it if you want it, that
you can change the software or use pieces of it in new free programs; and th at you know you can do these things.
To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights. These
restrictions translate to certain responsibilities for you if you distribute copies of the software, or if you modify it.
For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have. You
must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights.
We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission to copy, distribute
and/or modify the software.
Also, for each author’s protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If the
software is modified by someone else and passed on, we want its recipients to know that what they have is not the original, so that any problems
introduced by others will not reflect on the original authors’ reputations.
Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will
individually obtain patent licenses, in effect making the program proprietary. To prevent this, we have made it clear that any patent must be licensed
for everyone’s free use or not licensed at all.
The precise terms and conditions for copying, distribution and modification follow.
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION
0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under
the terms of this General Public License. The “Program”, below, refers to any such program or work, and a “work based on the Program” means
either the Program or any derivative work under copyright law: that is to say, a work containing the Program or a portion of it, either verbatim or with
modifications and/or translated into another language. (Hereinafter, translation is included without limitation in the term “modification”.) Each licensee
is addressed as “you”.
Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running the
Program is not restricted, and the output from the Program is covered only if its contents constitute a work based on the Program (independent of
having been made by running the Program). Whether that is true depends on what the Program does.
1. You may copy and distribute verbatim copies of the Program’s source code as you receive it, in any medium, provided that you conspicuously
and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this
License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program.
You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.
2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy and distribute
such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions:
a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change.
b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any part
thereof, to be licensed as a whole at no charge to all third parties under the terms of this License.
c) If the modified program normally reads commands interactively when run, you must cause it, when started running for such interactive
use in the most ordinary way, to print or display an announcement including an appropriate copyright notice and a notice that there is no
warranty (or else, saying that you provide a warranty) and that users may redistribute the program under these conditions, and telling the
user how to view a copy of this License. (Exception: if the Program itself is interactive but does not normally print such an announcement,
your work based on the Program is not required to print an announcement.)
These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program, and can be
reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when
you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Program, the
distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each
and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to
control the distribution of derivative or collective works based on the Program.
In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program) on a volume of a
storage or distribution medium does not bring the other work under the scope of this License.
3. You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable form under the terms of Sections
1 and 2 above provided that you also do one of the following:
a) Accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1
and 2 above on a medium customarily used for software interchange; or,
b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of physically
performing source distribution, a complete machine-readable copy of the corresponding source code, to be distributed under the terms of
Sections 1 and 2 above on a medium customarily used for software interchange; or,
c) Accompany it with the information you received as to the offer to distribute corresponding source code. (This alternative is allowed only for
noncommercial distribution and only if you received the program in object code or executable form with such an offer, in accord with Subsection b
above.)
The source code for a work means the preferred form of the work for making modifications to it. For an executable work, complete source code
means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and
installation of the executable. However, as a special exception, the source code distributed need not include anything that is normally distributed (in
either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless
that component itself accompanies the executable.
If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the
source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along
with the object code.
4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt otherwise to
copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights under this License. However, parties who have
received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance.
5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the
Program or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the
Program (or any work based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying,
distributing or modifying the Program or works based on it.
6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original
licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the
recipients’ exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to this License.
7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions
are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from
the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent
obligations, then as a consequence you may not distribute the Program at all. For example, if a patent license would not permit royalty-free
redistribution of the Program by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this
License would be to refrain entirely from distribution of the Program.
If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and
the section as a whole is intended to apply in other circumstances.
It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section
has the sole purpose of protecting the integrity of the free software distribution system, which is implemented by public license practices. Many people have
made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the
author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice.
This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.
8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder
who places the Program under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted
only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License.
9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to time. Such new versions will
be similar in spirit to the present version, but may differ in detail to address new problems or concerns.
Each version is given a distinguishing version number. If the Program specifies a version number of this License which applies to it and “any later
version”, you have the option of following the terms and conditions either of that version or of any later version published by the Free Software
Foundation. If the Program does not specify a version number of this License, you may choose any version ever published by the Free Software
Foundation.
10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write to the author to ask
for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make
exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting
the sharing and reuse of software generally.
NO WARRANTY
11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED
BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE
THE PROGRAM “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY
AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL
NECESSARY SERVICING, REPAIR OR CORRECTION.
12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER
PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING
ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM
(INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD
PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. END OF TERMS AND CONDITIONS
How to Apply These Terms to Your New Programs
If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to achieve this is to make it free
software which everyone can redistribute and change under these terms.
To do so, attach the following notices to the program. It is safest to attach them to the start of each source file to most effectively convey the
exclusion of warranty; and each file should have at least the “copyright” line and a pointer to where the full notice is found.
One line to give the program’s name and a brief idea of what it does.
Copyright (C) <year> <name of author>
This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by
the Free Software Foundation; either version 2 of the License, or (at your option) any later version.
This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details.
You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software Foundation,
Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
Also add information on how to contact you by electronic and paper mail.
If the program is interactive, make it output a short notice like this when it starts in an interactive mode:
Gnomovision version 69, Copyright (C) year name of author Gnomovision comes with ABSOLUTELY NO WARRANTY; for details type
`show w’. This is free software, and you are welcome to redistribute it under certain conditions; type `show c’ for details.
The hypothetical commands `show w’ and `show c’ should show the appropriate parts of the General Public License. Of course, the commands you
use may be called something other than `show w’ and `show c’; they could even be mouse-clicks or menu items--whatever suits your program.
You should also get your employer (if you work as a programmer) or your school, if any, to sign a “copyright disclaimer” for the program, if
necessary. Here is a sample; alter the names:
Yoyodyne, Inc., hereby disclaims all copyright interest in the program `Gnomovision’ (which makes passes at compilers) written by James
Hacker.
signature of Ty Coon, 1 April 1989
Ty Coon, President of Vice
This General Public License does not permit incorporating your program into proprietary programs. If your program is a subroutine library, you may
consider it more useful to permit linking proprietary applications with the library. If this is what you want to do, use the GNU Library General Public
License instead of this License.
.GNU
Lesser General Public License (LGPL)
Version 2.1, February 1999
Copyright (C) 1991, 1999 Free Software Foundation, Inc. 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA Everyone is permitted
to copy and distribute verbatim copies of this license document, but changing it is not allowed.
[This is the first released version of the Lesser GPL. It also counts as the successor of the GNU Library Public License, version 2, hence the
version number 2.1.]
Preamble
The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public Licenses are
intended to guarantee your freedom to share and change free software--to make sure the software is free for all its users.
This license, the Lesser General Public License, applies to some specially designated software packages--typically libraries--of the Free Software
Foundation and other authors who decide to use it. You can use it too, but we suggest you first think carefully about whether this license or the
ordinary General Public License is the better strategy to use in any particular case, based on the explanations below.
When we speak of free software, we are referring to freedom of use, not price. Our General Public Licenses are designed to make sure that you
have the freedom to distribute copies of free software (and charge for this service if you wish); that you receive source code or can get it if you want
it; that you can change the software and use pieces of it in new free programs; and that you are informed that you can do these things.
To protect your rights, we need to make restrictions that forbid distributors to deny you these rights or to ask you to surrender these rights. These
restrictions translate to certain responsibilities for you if you distribute copies of the library or if you modify it.
For example, if you distribute copies of the library, whether gratis or for a fee, you must give the recipients all the rights that we gave you. You must
make sure that they, too, receive or can get the source code. If you link other code with the library, you must provide complete object files to the
recipients, so that they can relink them with the library after making changes to the library and recompiling it. And you must show them these terms
so they know their rights.
We protect your rights with a two-step method: (1) we copyright the library, and (2) we offer you this license, which gives you legal permission to
copy, distribute and/or modify the library.
To protect each distributor, we want to make it very clear that there is no warranty for the free library. Also, if the library is modified by someone else
and passed on, the recipients should know that what they have is not the original version, so that the original author’s reputation will not be affected
by problems that might be introduced by others.
Finally, software patents pose a constant threat to the existence of any free program. We wish to make sure that a company cannot effectively
restrict the users of a free program by obtaining a restrictive license from a patent holder. Therefore, we insist that any patent license obtained for a
version of the library must be consistent with the full freedom of use specified in this license.
Most GNU software, including some libraries, is covered by the ordinary GNU General Public License. This license, the GNU Lesser General Public
License, applies to certain designated libraries, and is quite different from the ordinary General Public License. We use this license for certain libraries
in order to permit linking those libraries into non-free programs.
When a program is linked with a library, whether statically or using a shared library, the combination of the two is legally speaking a combined work,
a derivative of the original library. The ordinary General Public License therefore permits such linking only if the entire combination fits its criteria of
freedom.
The Lesser General Public License permits more lax criteria for linking other code with the library.
We call this license the “Lesser” General Public License because it does Less to protect the user’s freedom than the ordinary General Public License.
It also provides other free software developers Less of an advantage over competing non-free programs. These disadvantages are the reason we
use the ordinary General Public License for many libraries. However, the Lesser license provides advantages in certain special circumstances.
For example, on rare occasions, there may be a special need to encourage the widest possible use of a certain library, so that it becomes a de-facto
standard. To achieve this, non-free programs must be allowed to use the library. A more frequent case is that a free library does the same job as
widely used non-free libraries. In this case, there is little to gain by limiting the free library to free software only, so we use the Lesser General Public
License.
In other cases, permission to use a particular library in non-free programs enables a greater number of people to use a large body of free software.
For example, permission to use the GNU C Library in non-free programs enables many more people to use the whole GNU operating system, as
well as its variant, the GNU/Linux operating system.
Although the Lesser General Public License is Less protective of the users’ freedom, it does ensure that the user of a program that is linked with the
Library has the freedom and the wherewithal to run that program using a modified version of the Library.
The precise terms and conditions for copying, distribution and modification follow. Pay close attention to the difference between a “work based
on the library” and a “work that uses the library”. The former contains code derived from the library, whereas the latter must be combined with the
library in order to run.
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION
0. This License Agreement applies to any software library or other program which contains a notice placed by the copyright holder or other
authorized party saying it may be distributed under the terms of this Lesser General Public License (also called “this License”). Each licensee is
addressed as “you”.
A “library” means a collection of software functions and/or data prepared so as to be conveniently linked with application programs (which use some
of those functions and data) to form executables.
The “Library”, below, refers to any such software library or work which has been distributed under these terms. A “work based on the Library”
means either the Library or any derivative work under copyright law: that is to say, a work containing the Library or a portion of it, either verbatim
or with modifications and/ or translated straightforwardly into another language. (Hereinafter, translation is included without limitation in the term
“modification”.)
“Source code” for a work means the preferred form of the work for making modifications to it. For a library, complete source code means all the
source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of
the library.
Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running a
program using the Library is not restricted, and output from such a program is covered only if its contents constitute a work based on the Library
(independent of the use of the Library in a tool for writing it). Whether that is true depends on what the Library does and what the program that uses
the Library does.
1. You may copy and distribute verbatim copies of the Library’s complete source code as you receive it, in any medium, provided that you
conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that
refer to this License and to the absence of any warranty; and distribute a copy of this License along with the Library.
You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.
2. You may modify your copy or copies of the Library or any portion of it, thus forming a work based on the Library, and copy and distribute such
modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions:
a) The modified work must itself be a software library.
b) You must cause the files modified to carry prominent notices stating that you changed the files and the date of any change.
c) You must cause the whole of the work to be licensed at no charge to all third parties under the terms of this License.
d) If a facility in the modified Library refers to a function or a table of data to be supplied by an application program that uses the facility,
other than as an argument passed when the facility is invoked, then you must make a good faith effort to ensure that, in the event an
application does not supply such function or table, the facility still operates, and performs whatever part of its purpose remains meaningful.
(For example, a function in a library to compute square roots has a purpose that is entirely well-defined independent of the application.
Therefore, Subsection 2d requires that any application-supplied function or table used by this function must be optional: if the application
does not supply it, the square root function must still compute square roots.)
These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Library, and can
be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections
when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on
the Library, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire
whole, and thus to each and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise
the right to control the distribution of derivative or collective works based on the Library.
In addition, mere aggregation of another work not based on the Library with the Library (or with a work based on the Library) on a volume
of a storage or distribution medium does not bring the other work under the scope of this License.
3. You may opt to apply the terms of the ordinary GNU General Public License instead of this License to a given copy of the Library. To do this,
you must alter all the notices that refer to this License, so that they refer to the ordinary GNU General Public License, version 2, instead of to this
License. (If a newer version than version 2 of the ordinary GNU General Public License has appeared, then you can specify that version instead if you
wish.) Do not make any other change in these notices.
Once this change is made in a given copy, it is irreversible for that copy, so the ordinary GNU General Public License applies to all subsequent
copies and derivative works made from that copy.
This option is useful when you wish to copy part of the code of the Library into a program that is not a library.
4. You may copy and distribute the Library (or a portion or derivative of it, under Section 2) in object code or executable form under the terms
of Sections 1 and 2 above provided that you accompany it with the complete corresponding machine-readable source code, which must be
distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange.
If distribution of object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code
from the same place satisfies the requirement to distribute the source code, even though third parties are not compelled to copy the source along
with the object code.
5. A program that contains no derivative of any portion of the Library, but is designed to work with the Library by being compiled or linked with it, is called a
“work that uses the Library”. Such a work, in isolation, is not a derivative work of the Library, and therefore falls outside the scope of this License.
However, linking a “work that uses the Library” with the Library creates an executable that is a derivative of the Library (because it contains portions
of the Library), rather than a “work that uses the library”. The executable is therefore covered by this License. Section 6 states terms for distribution
of such executables.
When a “work that uses the Library” uses material from a header file that is part of the Library, the object code for the work may be a derivative work
of the Library even though the source code is not. Whether this is true is especially significant if the work can be linked without the Library, or if the
work is itself a library. The threshold for this to be true is not precisely defined by law.
If such an object file uses only numerical parameters, data structure layouts and accessors, and small macros and small inline functions (ten lines or
less in length), then the use of the object file is unrestricted, regardless of whether it is legally a derivative work. (Executables containing this object
code plus portions of the Library will still fall under Section 6.)
Otherwise, if the work is a derivative of the Library, you may distribute the object code for the work under the terms of Section 6. Any executables
containing that work also fall under Section 6, whether or not they are linked directly with the Library itself.
6. As an exception to the Sections above, you may also combine or link a “work that uses the Library” with the Library to produce a work containing
portions of the Library, and distribute that work under terms of your choice, provided that the terms permit modification of the work for the
customer’s own use and reverse engineering for debugging such modifications.
You must give prominent notice with each copy of the work that the Library is used in it and that the Library and its use are covered by this License.
You must supply a copy of this License. If the work during execution displays copyright notices, you must include the copyright notice for the Library
among them, as well as a reference directing the user to the copy of this License. Also, you must do one of these things:
a) Accompany the work with the complete corresponding machine-readable source code for the Library including whatever changes were
used in the work (which must be distributed under Sections 1 and 2 above); and, if the work is an executable linked with the Library, with
the complete machinereadable “work that uses the Library”, as object code and/or source code, so that the user can modify the Library
and then relink to produce a modified executable containing the modified Library. (It is understood that the user who changes the contents
of definitions files in the Library will not necessarily be able to recompile the application to use the modified definitions.)
b) Use a suitable shared library mechanism for linking with the Library. A suitable mechanism is one that (1) uses at run time a copy of the
library already present on the user’s computer system, rather than copying library functions into the executable, and (2) will operate properly
with a modified version of the library, if the user installs one, as long as the modified version is interface-compatible with the version that the
work was made with.
c) Accompany the work with a written offer, valid for at least three years, to give the same user the materials specified in Subsection 6a,
above, for a charge no more than the cost of performing this distribution.
d) If distribution of the work is made by offering access to copy from a designated place, offer equivalent access to copy the above
specified materials from the same place.
e) Verify that the user has already received a copy of these materials or that you have already sent this user a copy.
For an executable, the required form of the “work that uses the Library” must include any data and utility programs needed for reproducing the
executable from it. However, as a special exception, the materials to be distributed need not include anything that is normally distributed (in either
source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that
component itself accompanies the executable.
It may happen that this requirement contradicts the license restrictions of other proprietary libraries that do not normally accompany the operating system.
Such a contradiction means you cannot use both them and the Library together in an executable that you distribute.
7. You may place library facilities that are a work based on the Library side-by-side in a single library together with other library facilities not covered
by this License, and distribute such a combined library, provided that the separate distribution of the work based on the Library and of the other
library facilities is otherwise permitted, and provided that you do these two things:
a) Accompany the combined library with a copy of the same work based on the Library, uncombined with any other library facilities. This
must be distributed under the terms of the Sections above.
b) Give prominent notice with the combined library of the fact that part of it is a work based on the Library, and explaining where to find the
accompanying uncombined form of the same work.
8. You may not copy, modify, sublicense, link with, or distribute the Library except as expressly provided under this License. Any attempt otherwise
to copy, modify, sublicense, link with, or distribute the Library is void, and will automatically terminate your rights under this License. However,
parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full
compliance.
9. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute
the Library or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing
the Library (or any work based on the Library), you indicate your acceptance of this License to do so, and all its terms and conditions for copying,
distributing or modifying the Library or works based on it.
10. Each time you redistribute the Library (or any work based on the Library), the recipient automatically receives a license from the original licensor
to copy, distribute, link with or modify the Library subject to these terms and conditions. You may not impose any further restrictions on the
recipients’ exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties with this License.
11. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions
are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you
from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other
pertinent obligations, then as a consequence you may not distribute the Library at all. For example, if a patent license would not permit royalty-free
redistribution of the Library by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this
License would be to refrain entirely from distribution of the Library.
If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply, and
the section as a whole is intended to apply in other circumstances.
It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this
section has the sole purpose of protecting the integrity of the free software distribution system which is implemented by public license practices.
Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application
of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot
impose that choice.
This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.
12. If the distribution and/or use of the Library is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who
places the Library under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in
or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License.
13. The Free Software Foundation may publish revised and/or new versions of the Lesser General Public License from time to time. Such new
versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns.
Each version is given a distinguishing version number. If the Library specifies a version number of this License which applies to it and “any later
version”, you have the option of following the terms and conditions either of that version or of any later version published by the Free Software
Foundation. If the Library does not specify a license version number, you may choose any version ever published by the Free Software Foundation.
14. If you wish to incorporate parts of the Library into other free programs whose distribution conditions are incompatible with these, write to
the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we
sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software
and of promoting the sharing and reuse of software generally.
NO WARRANTY
15. BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE LIBRARY, TO THE EXTENT PERMITTED
BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE
THE LIBRARY “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND
PERFORMANCE OF THE LIBRARY IS WITH YOU. SHOULD THE LIBRARY PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY
SERVICING, REPAIR OR CORRECTION.
16. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER
PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE LIBRARY AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING
ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE LIBRARY
(INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD
PARTIES OR A FAILURE OF THE LIBRARY TO OPERATE WITH ANY OTHER SOFTWARE), EVEN IF SUCH HOLDER OR OTHER PARTY HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
How to Apply These Terms to Your New Libraries
If you develop a new library, and you want it to be of the greatest possible use to the public, we recommend making it free software that everyone
can redistribute and change. You can do so by permitting redistribution under these terms (or, alternatively, under the terms of the ordinary General
Public License).
To apply these terms, attach the following notices to the library. It is safest to attach them to the start of each source file to most effectively convey
the exclusion of warranty; and each file should have at least the “copyright” line and a pointer to where the full notice is found.
<one line to give the library’s name and an idea of what it does.> Copyright (C) <year> <name of author>
This library is free software; you can redistribute it and/or modify it under the terms of the GNU Lesser General Public License as published
by the Free Software Foundation; either version 2.1 of the License, or (at your option) any later version.
This library is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU Lesser General Public License for more details.
You should have received a copy of the GNU Lesser General Public License along with this library; if not, write to the Free Software
Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
Also add information on how to contact you by electronic and paper mail.
You should also get your employer (if you work as a programmer) or your school, if any, to sign a “copyright disclaimer” for the library, if necessary.
Here is a sample; alter the names:
Yoyodyne, Inc., hereby disclaims all copyright interest in the library `Frob’ (a library for tweaking knobs) written by James Random Hacker.
signature of Ty Coon, 1 April 1990
Ty Coon, President of Vice
That’s all there is to it!
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG
customer care center.
Region
North America
Latin America
Europe
CIS
Asia Pacific
Country
1-800-SAMSUNG(726-7864)
01-800-SAMSUNG(726-7864)
1-800-SAMSUNG(726-7864)
0800-333-3733
0800-124-421, 4004-0000
800-SAMSUNG(726-7864)
00-1800-5077267
800-7919267
0-800-507-7267
1-800-10-7267
800-6225
1-800-299-0013
1-800-234-7267
800-7267
1-800-682-3180
1-800-751-2676
1-800-SAMSUNG(726-7864)
0-800-100-5303
01-8000112112
BELGIUM
02 201 2418
CZECH REPUBLIC
DENMARK
FINLAND
FRANCE
GERMANY
HUNGARY
ITALIA
LUXEMBURG
NETHERLANDS
NORWAY
POLAND
PORTUGAL
SLOVAKIA
SPAIN
SWEDEN
U.K
EIRE
AUSTRIA
SWITZERLAND
RUSSIA
KAZAKHSTAN
UZBEKISTAN
KYRGYZSTAN
TADJIKISTAN
UKRAINE
LITHUANIA
LATVIA
ESTONIA
AUSTRALIA
NEW ZEALAND
CHINA
HONG KONG
INDIA
INDONESIA
JAPAN
MALAYSIA
800-SAMSUNG(800-726786)
8-SAMSUNG(7267864)
30-6227 515
01 48 63 00 00
01805 - SAMSUNG(726-7864 € 0,14/Min)
06-80-SAMSUNG(726-7864)
800-SAMSUNG(726-7864)
02 261 03 710
0900-SAMSUNG (0900-7267864) (€ 0,10/Min)
3-SAMSUNG(7267864)
0 801 1SAMSUNG(172678), 022-607-93-33
80820-SAMSUNG(726-7864)
0800-SAMSUNG(726-7864)
902-1-SAMSUNG (902 172 678)
075-SAMSUNG(726 78 64)
0845 SAMSUNG (7267864)
0818 717 100
0810-SAMSUNG(7267864, € 0.07/min)
0848-SAMSUNG(7267864, CHF 0.08/min)
8-800-555-55-55
8-10-800-500-55-500
8-10-800-500-55-500
00-800-500-55-500
8-10-800-500-55-500
8-800-502-0000
8-800-77777
8000-7267
800-7267
1300 362 603
0800 SAMSUNG (0800 726 786)
800-810-5858, 400-810-5858, 010-6475 1880
3698-4698
3030 8282, 1800 110011, 1-800-3000-8282
0800-112-8888
0120-327-527
1800-88-9999
1-800-10-SAMSUNG(726-7864)
1-800-3-SAMSUNG(726-7864), 02-5805777
1800-SAMSUNG(726-7864)
1800-29-3232, 02-689-3232
0800-329-999
1 800 588 889
444 77 11
0860-SAMSUNG(726-7864 )
800-SAMSUNG (726-7864), 8000-4726
PHILIPPINES
Middle East &
Africa
Contact Center 
CANADA
MEXICO
U.S.A
ARGENTINE
BRAZIL
CHILE
NICARAGUA
HONDURAS
COSTA RICA
ECUADOR
EL SALVADOR
GUATEMALA
JAMAICA
PANAMA
PUERTO RICO
REP. DOMINICA
TRINIDAD & TOBAGO
VENEZUELA
COLOMBIA
SINGAPORE
THAILAND
TAIWAN
VIETNAM
TURKEY
SOUTH AFRICA
U.A.E
Web Site
www.samsung.com/ca
www.samsung.com/mx
www.samsung.com/us
www.samsung.com/ar
www.samsung.com/br
www.samsung.com/cl
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com.co
www.samsung.com/be (Dutch)
www.samsung.com/be_fr (French)
www.samsung.com/cz
www.samsung.com/dk
www.samsung.com/fi
www.samsung.com/fr
www.samsung.de
www.samsung.com/hu
www.samsung.com/it
www.samsung.com/lu
www.samsung.com/nl
www.samsung.com/no
www.samsung.com/pl
www.samsung.com/pt
www.samsung.com/sk
www.samsung.com/es
www.samsung.com/se
www.samsung.com/uk
www.samsung.com/ie
www.samsung.com/at
www.samsung.com/ch
www.samsung.ru
www.samsung.com/kz_ru
www.samsung.com/kz_ru
www.samsung.ua
www.samsung.com/lt
www.samsung.com/lv
www.samsung.com/ee
www.samsung.com/au
www.samsung.com/nz
www.samsung.com/cn
www.samsung.com/hk
www.samsung.com/in
www.samsung.com/id
www.samsung.com/jp
www.samsung.com/my
www.samsung.com/ph
www.samsung.com/sg
www.samsung.com/th
www.samsung.com/tw
www.samsung.com/vn
www.samsung.com/tr
www.samsung.com/za
www.samsung.com/ae
Correct disposal of batteries in this product
(Applicable in the European Union and other European countries with separate battery return systems.)
This marking on the battery, manual or packaging indicates that the batteries in this product should not be
disposed of with other household waste at the end of their working life. Where marked, the chemical symbols
Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the reference levels in EC
Directive 2006/66. If batteries are not properly disposed of, these substances can cause harm to human
health or the environment.
To protect natural resources and to promote material reuse, please separate batteries from other types of
waste and recycle them through your local, free battery return system.
Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its electronic
accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste at
the end of their working life. To prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate these items from other types of waste and recycle them responsibly to
promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local
government office, for details of where and how they can take these items for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract.
This product and its electronic accessories should not be mixed with other commercial wastes for disposal.
Code No. AK68-01785H
Download PDF