Samsung | DVD-1080P8 | Samsung DVD-1080P8 Benutzerhandbuch

DVD Player
DVD-1080P8
www.samsung.com
AK68-01503Q
PRECAUTIONS
1. Setting up
- Refer to the identification label located on
the rear of your player for its proper operating voltage.
- Install your player in a cabinet with adequate ventilation holes. (7~10cm) Do not
block ventilation holes on any of the components for air circulation.
- Do not push the disc tray in by hand.
- Do not stack components.
- Be sure to turn all components off before
moving the player.
- Before connecting other components to this
player, be sure to turn them off.
- Be sure to remove the disc and turn off the
player after use, especially if you are not
going to use it for a long time.
- The mains plug is used as a disconnect
device and shall stay readily operable at
any time.
2. For your safety
- This product utilizes a laser. Use of controls
or adjustments or performance of procedures other than those specified herein may
result in hazardous radiation exposure.
- Do not open covers and do not repair yourself. Refer servicing to qualified personal.
3. Caution
- Your player is not intended for industrial use
but for domestic purposes. Use of this product is for personal use only.
- Apparatus shall not be exposed to dripping
or splashing and no objects filled with liquids, such as vases, shall be placed on the
apparatus.
- Exterior influences such as lightning and
static electricity can affect normal operation
of this player. If this occurs, turn the player
off and on again with the POWER button, or
disconnect and then reconnect the AC
power cord to the AC power outlet. The
player will operate normally.
- When condensation forms inside the player
due to sharp changes in temperature, the
2
player may not operate correctly. If this
occurs, leave the player at room temperature until the inside of the player becomes
dry and operational.
4. Disc
- Do not clean disc using record-cleaning
sprays, benzene, thinner, or other volatile
solvents that may cause damage to the disc
surface.
- Do not touch the disc’s signal surface. Hold
by the edges or by one edge and the hole
in the center.
- Wipe the dirt away gently; never wipe a
cloth back and forth over the disc.
5. Environmental info
- The battery used in this product contains
chemicals that are harmful to the environ
ment.
- So, dispose of batteries in the proper man
ner, according to federal, state, and local
regulations.
The product unit accompanying this user manual is
licensed under certain intellectual property rights of
certain third parties. This license is limited to private
non-commercial use by end-user consumers for
licensed contents. No rights are granted for
commercial use. The license does not cover any
product unit other than this product unit and the
license does not extend to any unlicensed product
unit or process conforming to ISO/OUR 11172-3 or
ISO/OUR 13818-3 used or sold in combination with
this product unit. The license only covers the use of
this product unit to encode and/or decode audio files
conforming to the ISO/OUR 11172-3 or ISO/OUR
13818-3. No rights are granted under this license for
product features or functions that do not conform to
the ISO/OUR 11172-3 or ISO/OUR 13818-3.
CAUTION: USE OF ANY CONTROLS,
ADJUSTMENTS, OR PROCEDURES OTHER
THAN SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
Accessories
Remote Control
User’s Manual
Batteries for Remote
Control (AAA Size)
Video/Audio
Cable
Install Batteries in the Remote control
1. Open the battery cover on the back of the remote
control.
2. Insert two AAA batteries.
Make sure that the
polarities (+ and -) are aligned correctly.
3. Replace the battery cover.
If remote control doesn’t operate
properly:
- Check the polarity + - of the batteries (Dry-Cell)
- Check if the batteries are drained.
- Check if remote control sensor is blocked by
obstacles.
- Check if there is any fluorescent lighting nearby.
TABLE OF
CONTENTS
Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Before you start . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Setup
General Features . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Disc Type and Characteristics . . . . . . . . . . . . . . . . 5
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Tour of the Remote Control . . . . . . . . . . . . . . . . . . 8
Connections
Choosing a Connection . . . . . . . . . . . . . . . . . . . . . 9
Basic Functions
Playing a Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Using the Search and Skip Functions . . . . . . . . . 14
Using the Display Function . . . . . . . . . . . . . . . . . 14
Using the Disc and Title Menu . . . . . . . . . . . . . . 15
Using the Function Menu . . . . . . . . . . . . . . . . . . 15
Repeat Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Slow Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Advanced Functions
Adjusting the Aspect Ratio (EZ View) . . . . . . . . . 16
Selecting the Audio Language . . . . . . . . . . . . . . . 17
Selecting the Subtitle Language. . . . . . . . . . . . . . 17
Changing the Camera Angle . . . . . . . . . . . . . . . . 18
Using the Instant Replay/Skip Function . . . . . . . . 18
Using the Bookmark Function . . . . . . . . . . . . . . . 18
Using the Zoom Function . . . . . . . . . . . . . . . . . . . 19
Clips Menu for MP3/WMA/JPEG/MPEG4/
CD Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Folder Selection . . . . . . . . . . . . . . . . . . . . . . . . . . 19
MP3/WMA/CD Audio Playback. . . . . . . . . . . . . . . 20
MPEG4 Playback . . . . . . . . . . . . . . . . . . . . . . . . . 20
Picture CD Playback. . . . . . . . . . . . . . . . . . . . . . . 22
Changing Setup Menu
Using the Setup Menu . . . . . . . . . . . . . . . . . . . . . 23
Setting Up the Language Features . . . . . . . . . . . 23
Setting Up the Audio Options . . . . . . . . . . . . . . . . 24
Setting Up the Display Options . . . . . . . . . . . . . . 25
Setting Up the Parental Control . . . . . . . . . . . . . . 27
Setting Up the Anynet+(HDMI-CEC) . . . . . . . . . . 28
Reference
Firmware Upgrade . . . . . . . . . . . . . . . . . . . . . . . . 29
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
3
English
BEFORE YOU
STAR T
SETUP
General Features
Excellent Sound
Dolby Digital, a technology developed by Dolby
Laboratories, provides crystal clear sound reproduction.
Screen
Both regular and widescreen(16:9) pictures can be
viewed.
Slow Motion
An important scene can be viewed in slow motion.
1080p Playback
This player upconverts regular DVDs for playback
on 1080p TVs.
Parental Control (DVD)
The parental control allows users to set the level
necessary to prohibit children from viewing harmful
movies such as those with violence, adult subject
matter, etc.
Note
- Discs which cannot be played with this
player.
• DVD-ROM
• DVD-RAM
• CD-ROM
• CDV
• CDI
• CVD
• CDGs play audio only, not graphics.
- Ability to play back may depend on recording
conditions.
• DVD-R, +R
• CD-RW
• DVD+RW, -RW (V mode)
- The unit may not play certain CD-R, CD-RW
and DVD-R due to the disc type or recording
conditions.
COPY PROTECTION
Digital Photo Viewer (JPEG)
You can view Digital Photos on your TV.
Many DVD discs are encoded with copy protection.
Because of this, you should only connect your DVD
player directly to your TV, not to a VCR. Connecting
to a VCR results in a distorted picture from copyprotected DVD discs.
This product incorporates copyright protection
technology that is protected by methods claims of
certain U.S. patents and other intellectual property
rights owned by Macrovision Corporation and other
rights owners. Use of this copyright protection technology must be auzthorized by Macrovision
Corporation, and is intended for home and other
limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
Repeat
You can repeat a song or movie simply by pressing
the REPEAT button.
PROGRESSIVE SCAN OUTPUTS
(525p,720p,1080p)
Various On-Screen Menu Functions
You can select various languages (Audio/Subtitle)
and screen angles while enjoying movies.
Progressive Scan
Progressive scanning creates an improved picture
with double the scan lines of a conventional interlaced picture.
EZ VIEW (DVD)
Easy View enables picture adjustment to match
your TV's screen size (16:9 or 4:3).
MP3/WMA
This unit can play discs created from MP3/WMA
files.
Instant Replay (DVD)
This function is used to replay the previous 10
seconds of a movie from the current position.
Instant Skip (DVD)
This function skips playback ahead 10 seconds
MPEG4
This unit can play MPEG4 formats within an avi file.
HDMI (High Definition Multimedia
Interface)
HDMI reduces picture noise by allowing a pure
digital video/audio signal path from the player to
your TV.
4
“CONSUMERS SHOULD NOTE THAT NOT ALL
HIGH DEFINITION TELEVISION SETS ARE FULLY
COMPATIBLE WITH THIS PRODUCT AND MAY
CAUSE ARTIFACTS TO BE DISPLAYED IN THE
PICTURE, IN CASE OF 525, 720, 1080 PROGRESSIVE SCAN PICTURE PROBLEMS, IT IS
RECOMMENDED THAT THE USER SWITCH THE
CONNECTION TO THE ‘STANDARD DEFINITION’
OUTPUT. IF THERE ARE QUESTIONS
REGARDING YOUR TV SET COMPATIBILITY
WITH THIS MODEL 525p, 720p, 1080p DVD PLAYER, PLEASE CONTACT SAMSUNG'S CUSTOMER
SERVICE CENTER.”
Disc Type and Characteristics
This DVD player is capable of playing the following types of discs with the corresponding logos:
Recording Types
DVD
Audio
+
Video
AUDIO-CD
Disc Size
Max. Playing Time
12 Cm
Single-sided 240 min.
Double-sided 480 min.
- DVD contains excellent sound and
video due to Dolby Digital and MPEG2 system.
8 Cm
Single-sided 80 min.
Double-sided 160 min.
- Various screen and audio functions
can be easily selected through the onscreen menu.
12 Cm
74 min.
8 Cm
20 min.
Audio
Characteristics
- CD is recorded as a Digital Signal
with better audio quality, less distortion and less deterioration of audio
quality over time.
Disc Markings
Region Number
~
PAL
Play Region Number
PAL broadcast system in U.K, France,
Germany, etc.
Dolby Digital disc
STEREO
DIGITAL
SOUND
Stereo disc
Digital Audio disc
Both the DVD player and the discs are coded
by region. These regional codes must match in
order for the disc to play. If the codes do not
match, the disc will not play.
The Region Number for this player is
described on the rear panel of the player.
DTS disc
MP3 disc
You must only insert one DVD disc at a time.
Inserting two or more discs will not allow to
play them back and it may cause damage to
the DVD player.
DivX Certification
DivX, DivX Certified,
and associated logos are trademarks of
DivXNetworks, Inc and are used under
license
5
English
Disc Types (Logos)
Description
Front Panel Controls
2
1
4
3
8
7
6
5
1.
DISC TRAY
Place the disc here.
5.
SKIP (
) / SEARCH
Use to forward skip a scene or music.
2.
OPEN/CLOSE (
)
Press to open and close the disc tray.
6.
STOP (
)
Stops disc play.
3.
DISPLAY
Operation indicators are displayed here.
7.
SKIP (
) / SEARCH
Use to reverse skip a scene or music.
4.
PLAY/PAUSE (
)
Begin or pause disc play.
8.
STANDBY/ON (
)
When STANDBY/ON is pressed on, the indicator goes
out and the player is turned on.
Front Panel Display
1
2
4
5
DVD
CD
3
6
RW
HDMI
1080iP720P
8
1.
STOP, PAUSE and OPEN/CLOSE
7.
HDMI 720P ➔ “HDMI + 720P”,
PLAYBACK, SKIP/SEARCH
HDMI 1080i ➔ “HDMI + 1080i”,
indicator
3.
In Disc Indicator : DVD Video, Audio
HDMI 1080P ➔ “HDMI + 1080P”
8.
Displays the Total playing time and
CD, CD-R/RW, DVD-R/RW/RAM,
various messages concerning
DVD+R/RW
operations such as PLAY, STOP,
4.
DVD VIEW indicator
5.
CD indicator
6.
Disc Media indicator : DVD-R, DVDRW, DVD+R, DVD+RW
6
HDMI indicator :
HDMI 480P ➔ “HDMI”,
indicator
2.
7
LOAD ...
NOdSC: No disc loaded.
OPEn: The disc tray is open.
LOAd: Player is loading disc information.
Rear Panel
1
3
English
2
4
3
1.
SCART JACK
- Connect to a TV scart input jack.
2.
AUDIO OUT JACKS
- Connect to the Audio input jacks of your television or
audio/video receiver.
3.
DIGITAL AUDIO OUT JACKS
- Use either an optical or coaxial digital cable to connect to a compatible Dolby Digital receiver.
- Use either an optical or coaxial digital cable to connect to an A/V Amplifier that contains a Dolby Digital,
MPEG2 or DTS decoder.
5
4.
VIDEO OUT JACK
- Use a video cable to connect to the Video input jack
on your television.
5.
HDMI OUT JACK
- Use the HDMI cable to connect this jack to the HDMI
jack on your television for the best quality picture.
- If an HDMI cable is connected to an HDMI-compatible TV, HDMI will be output automatically within 10
seconds.
Note
- Consult your TV User’s Manual to find out if your TV supports Progressive Scan (P-SCAN).
If Progressive Scan is supported, follow the TV User’s Manual regarding Progressive Scan settings in
the TV’s menu system.
- The HDMI output of this unit can be connected to a DVI jack on a TV or other device using a conversion adapter. In this case, it is necessary to use a TV or display with an HDCP-compatible DVI input.
- There may be no image output if the DVD player is connected to a TV or display that is not compatible
with the above format.
- Refer to the TV's instruction manual for detailed information regarding the HDMI terminal.
- See pages 25 ~ 26 to get more information on how to use the setup menu.
7
Tour of the Remote Control
7.
1
2
17
18
8.
3
19
20
9.
10.
11.
4
12.
5
21
22
6
7
8
9
23
24
15.
16.
10
25
17.
18.
11
26
27
13.
14.
19.
20.
12
21.
13
28
14
29
15
16
30
31
22.
23.
24.
25.
26.
27.
1.
2.
3.
4.
5.
6.
8
VIDEO SEL. Button
Change Video output mode.
HDMI SEL. Button
HDMI Output resolution setup.
DVD POWER Button
Turns the power on or off.
NUMBER Buttons
BOOKMARK Buttons
SEARCH Buttons (
)
/
Allow you to search forward/backward through a disc.
28.
29.
30.
31.
INSTANT REPLAY Button
This function is used to replay the previous 10 seconds
of a movie from the current position.
SKIP Buttons (
)
/
Use to skip the title, chapter or track.
STOP Button (
)
TV VOL (+, -) Buttons
Control volume
MENU Button
Brings up the DVD player’s menu.
›/‚,¥/Š Buttons
ENTER/›
This button functions as a toggle switch.
EZ VIEW Button
The aspect ratio of a picture can easily be adjusted
according to the screen size of your TV (16:9 or 4:3).
DISC MENU Button
Brings up the Disc menu.
SUBTITLE Button
AUDIO Button
Use this button to access various audio functions on a disc.
REPEAT A-B Button
Allows you to repeat play A-B on a disc.
REPEAT Button
Allows you to repeat play a title, chapter, track, or disc.
TV POWER Button
Turn the TV’s power on or off.
OPEN/CLOSE (
) Button
To open and close the disc tray.
INSTANT SKIP Button
This function skips playback ahead 10 seconds.
STEP Button
Advances play one frame at a time.
PAUSE Button ( )
Pause disc play.
PLAY Button ( )
Begin disc play.
TV CH (
,
) buttons
Channel selection.
TV/VIDEO Button
Press to display all of the available video sources (i,e.,
TV, Cable, Video).
RETURN Button
Returns to a previous menu.
EXIT Button
Exit the on-screen menu.
CANCEL Button
Use to remove menus or status displays from the screen.
ZOOM Button
Enlarge DVD Picture
INFO Button
Displays the current disc mode.
CONNECTIONS
The following shows examples of connections commonly used to connect the DVD player with a TV and
other components.
Before Connecting the DVD Player
- Always turn off the DVD player, TV, and other components before you connect or disconnect any cables.
- Refer to the user’s manual of the additional components you are connecting for more information on those
particular components.
Connecting to a TV (SCART)
- Using the SCART, connect the SCART (EXT) terminal on the rear of the DVD Player to the SCART (IN)
terminal of your TV.
- If your TV is not equipped with a SCART you can select one of the following alternative connections:
Connecting to a TV (VIDEO CVBS)
1
Using video/audio cables, connect the VIDEO
(yellow)/AUDIO (red and white) OUT terminals on the rear
of the DVD player to the VIDEO (yellow)/AUDIO (red and
white) IN terminals of TV.
WHITE
2
Turn on the DVD player and TV.
RED
YELLOW
Audio
Cable
OR
RED
WHITE
Video Cable
YELLOW
3
Press the input selector on your TV remote control until the
Video signal from the DVD player appears on the TV
screen.
Note
- Noise may be generated if the audio cable is too close to the power cable.
- If you want to connect to an Amplifier, please refer to the Amplifier connection page. (See pages 11 to 12)
- The number and position of terminals can vary depending on your TV set. Please refer to the user's manual of the TV.
- If there is one audio input terminal on the TV, connect it to the [AUDIO OUT][left] (white) terminal of the
DVD player.
- If you press the VIDEO SEL. button when DVD Player is in stop mode or no disc is inserted, the Video Output
mode changes in the following sequence: (P-SCAN ➝ SCART CVBS ➝ SCART RGB)
9
English
Choosing a Connection
Connecting to a TV with DVI Jack
1
Using the HDMI-DVI cable (not included), connect the
HDMI OUT terminal on the rear of the DVD player to the
DVI IN terminal of your TV.
WHITE
2
Using the audio cables, connect the AUDIO (red and
white) OUT terminals on the rear of the DVD player to the
AUDIO (red and white) IN terminals of your TV.
Turn on the DVD player and TV.
RED
Audio Cable
RED
WHITE
HDMI-DVI cable
(Not Included)
3
Press the input selector on your TV remote control until the
DVI signal from the DVD player appears on your TV
screen.
Connecting to a TV with HDMI Jack
1
Using the HDMI-HDMI cable connect the HDMI OUT terminal on the rear of the DVD player to the HDMI IN terminal
of your TV.
2
Press the input selector on your TV remote control until the
HDMI signal from the DVD player appears on your TV
screen.
HDMI cable
(Not Included)
HDMI VIDEO Specifications
When you press the HDMI SEL. button, 480p, 576p, 720p, 1080p, 1080i are selected in order.
The first press of the HDMI SEL. button brings up the current resolution.
The second press allows you to change the HDMI output resolution.
- Depending on your TV, certain HDMI output resolutions may not work.
- Please refer to the user's manual of your TV.
- If HDMI or HDMI-DVI cable is plugged into TV, the DVD player’s output is set to HDMI/DVI within 10
seconds.
- If you set the HDMI output resolution 720p,1080p or 1080i, HDMI output provides better picture
quality.
- If you connect an HDMI cable between Samsung TV and this DVD player, you can operate this DVD player
using your TV remote control. This is only available with Samsung TVs that support Anynet+(HDMI-CEC).
(See page 28).
- If your TV has an
logo, then it will
Supports the Anynet+ Function.
10
HDMI is an interface to enable the digital transmission
of video and audio data with just a single connector.
Using HDMI, the DVD player transmits a digital video
and audio signal and displays a vivid picture on a TV
having an HDMI input jack.
• HDMI connection description
HDMI connector - Both uncompressed video data and
digital audio data (LPCM or Bit Stream data).
- Though the player uses a HDMI cable, the player
outputs only a pure digital signal to the TV.
- If TV does not support HDCP (High-bandwidth
Digital content protection), snow noise appears on
the screen.
• Why does Samsung use HDMI?
Analog TVs require an analog video/audio signal.
However, when playing a DVD, the data transmitted
to a TV is digital. Therefore either a digital-to-analog
converter (in the DVD player) or an analog-to-digital
converter (in the TV) is required. During this conversion, the picture quality is degraded due to noise and
signal loss. DVI technology is superior because it
requires no D/A conversion and is a pure digital signal from the player to your TV.
• What is the HDCP?
HDCP (High-bandwidth Digital Content Protection) is
a system for protecting DVD content outputted via
DVI from being copied. It provides a secure digital
link between a video source (PC, DVD. etc) and a
display device (TV, projector . etc). Content is
encrypted at the source device to prevent unauthorized
Connection to an Audio System (2 Channel Amplifier)
1
Using the audio cables, connect the AUDIO (red and
white) OUT terminals on the rear of the DVD player to the
AUDIO (red and white) IN terminals of the Amplifier.
2
Using the video signal cable(s), connect the VIDEO OUT
terminals on the rear of the DVD player to the VIDEO IN
terminal of your TV as described on pages 9 to 11.
WHITE
RED
3
Audio Cable
Turn on the DVD player, TV, and Amplifier.
RED
WHITE
2-Channel stereo amp
4
Press the input select button of the Amplifier to select
external input in order to hear sound from the DVD player.
Note
- Please turn the volume down when you turn on the Amplifier. Sudden loud sound may cause
damage to the speakers and your ears.
- Please set the audio in the menu screen according to the Amplifier. (See pages 24 to 25)
- The position of terminals can vary depending on the Amplifier.
Please refer to the user's manual of the Amplifier.
11
English
• HDMI (High Definition Multimedia Interface)
Connection to an Audio System (Dolby digital, MPEG2 or DTS Amplifier)
1
If using an optical cable (not included), connect the DIGITAL AUDIO OUT (OPTICAL) terminal on the rear of the
DVD player to the DIGITAL AUDIO IN (OPTICAL) terminal
of the Amplifier.
If using a coaxial cable (not included), connect the DIGITAL AUDIO OUT (COAXIAL) terminal on the rear of the
DVD player to the DIGITAL AUDIO IN (COAXIAL) terminal of the Amplifier.
2
Using the video signal cable(s), connect the VIDEO or
HDMI OUT terminals on the rear of the DVD player to the
VIDEO or DVI IN terminals of your TV as described on
pages 9 to 11.
or
Coaxial Cable
(not included)
Optical Cable
(not included)
3
Dolby digital or
DTS amp
Turn on the DVD player, TV, and Amplifier.
4
Press the input select button of the Amplifier to select
external input in order to hear sound from the DVD player.
Refer to your Amplifier's user manual to set the Amplifier's
audio input.
Note
- Please turn the volume down when you turn on the Amplifier. Sudden loud sound may cause
damage to the speakers and your ears.
- Please set the audio in the menu screen according to the Amplifier. (See pages 24 to 25)
- The position of terminals can vary depending on the Amplifier.
Please refer to the user's manual of the Amplifier.
- Please remove the dust cover before using the optical cable (not included) and put the cover on the cable
again when it's not used.
12
BASIC FUNCTIONS
Before Play
- Turn on your TV and set it to the correct Video
Input by pressing TV/VIDEO button on the TV
remote control.
- If you connected an external Audio System, turn
on your Audio System and set it to the correct
Audio Input.
After plugging in the player, the first time you press the DVD
POWER button, this screen comes up: If you want to select
a language, press a NUMBER button. (This screen will only
appear when you plug in the player for the first time.)
If the language for the startup screen is not set, the settings
may change whenever you turn the power on or off.
Therefore, make sure that you select the language you want
to use.
Once you select a menu language, you can change it by
pressing the
button on the front panel of the unit for
more than 5 seconds with no disc in the unit. Then the
SELECT MENU LANGUAGE window appears again where
you can reset your preferred language.
Press
1
for English
Touche
2
pour Français
Drücken Sie
3
für Deutsch
Pulsar
4
para Español
Premere
5
per Italiano
Druk op
6
voor Nederlands
Playback
1. Press the OPEN/CLOSE ( ) button. The STANDBY
indicator light goes out and the tray opens.
2. Place a disc gently into the tray with the disc’s label facing
up.
3. Press the PLAY ( ) button or OPEN/CLOSE ( )
button to close the disc tray.
- When you stop disc play, the player remembers
where you stopped, so when you press PLAY( )
button again, it will pick up where you left off.
) button during play.
5. Removing Disc
Press the OPEN/CLOSE (
) button.
6. Pausing Play
Press the PAUSE ( ) or STEP button on the remote
control during play.
- Screen stops, no sound.
To resume, press the PLAY( ) button once again.
7. Step Motion Play (Except CD)
Press the STEP button on the remote control during play.
- Each time the button is pressed, a new frame will
appear.
- No sound is heard during STEP mode.
- Press the PLAY ( ) button to resume normal play.
- You can only perform step motion play in the
forward direction.
8. Slow Motion Play
Press the SEARCH ( / ) button to choose the play
speed between 1/8, 1/4 and 1/2 of normal during PAUSE
or STEP mode.
- No sound is heard during slow mode.
- Press the PLAY ( ) button to resume normal play.
Note
- If the player is left in the stop mode for more
than one minute without any user interaction, a
screen saver will be activated. Press the PLAY
( ) button to resume normal play.
- If the player is left in the stop mode for more than
about 30 minutes, the power will automatically
shut off. (Automatic Power-Off Function)
- If the player is left for about 5 minutes in pause
mode, it will stop.
- This (
) icon indicates an invalid button press.
13
English
4. Stopping Play
Press the STOP (
Playing a Disc
Using the Search and Skip
Functions
During play, you can search quickly through a chapter or
track, and use the skip function to jump to the next selection.
Searching through a Chapter or
Track
During play, press the SEARCH (
or
remote control for more than 1 second.
DVD
2X, 4X, 64X, 128X
CD
2X, 4X, 8X
Using the Display Function
When Playing a DVD/MPEG4
1. During play, press the INFO button on the remote control.
- You can select Info in the function menu by pressing
the MENU button.
2. Press the ›/‚buttons to select the desired item.
) button on the
3. Press the ¥/Š buttons to make the desired setup and then
press the ENTER button.
- You may use the number buttons of the remote control
to directly access a title, chapter or to start the play
back from a desired time.
4. To make the screen disappear, press the INFO button
again.
Note
- The speed marked in this function may be
different from the actual playback speed.
- No sound is hearing during search mode
(Except CD).
Note
Title
Skipping Tracks
During play, press the SKIP (
or
) button.
- When playing a DVD, if you press the SKIP (
Chapter
Most DVD discs are recorded in chapters so
that you can quickly find a specific passage.
Time
Allows playback of the film from a desired
time. You must enter the starting time as a
reference.The time search function does not
operate on some disc.
) button, it
moves to the next chapter. If you press the SKIP (
)
button, it moves to the beginning of the chapter. One more
press makes it move to the beginning of the previous
chapter.
- When playing a CD in Menu Off mode, if you press the
SKIP (
) button, it moves to the next track. If you press
the SKIP (
Audio
) button, it moves to the beginning of the
track. One more press makes it move to the beginning of
the previous track.
14
To access the desired title when there is
more than one in the disc. For example, if
there is more than one movie on a DVD,
each movie will be identified.
Subtitle
Refers to the language of the film soundtrack.
In the example, the soundtrack is played in
English 5.1CH. A DVD disc can have up to
eight different soundtracks.
Refers to the subtitle languages available in
the disc. You will be able to choose the
subtitle languages or, if you prefer, turn them
off from the screen. A DVD disc can have up
to 32 different subtitles.
Using the Disc and Title
Menu
Using the Function Menu
Using the Function Menu (DVD)
Using the Disc Menu
2. Press the ›/‚ buttons to select Disc Menu, then press the
Š or ENTER button.
Press ENTER key
for Disc Menu
Enter
Return
Using the Title Menu
1. During the playback of a DVD disc, press the MENU button
on the remote control.
2. Press the ›/‚ buttons to select Title Menu, then press the
Š or ENTER button.
Enter
Return
Menu
3. Press the ›/‚ buttons to select one of the six functions.
Then press the Š or ENTER button to access the function.
You can also directly select these functions using their
respective buttons on the remote control.
- INFO
- ZOOM
- EZ VIEW
- BOOKMARK
- REPEAT
Repeat Play
Repeat the current track, chapter, title, a chosen
section (A-B), or all of the disc.
When playing a DVD
Press ENTER key
for Title Menu
Return
Info
Zoom
Bookmark
Repeat
EZ View
Angle
Menu
Note
- Depending on a disc, the Disc Menu may not
work.
- You can also use the Disc Menu, using the
DISC MENU button on the remote control.
Enter
2. Press the ›/‚ buttons to select Function, then press the
Š or ENTER button.
- Info (See pages 14)
- Zoom (See page 19)
- Bookmark (See pages 18 to 19)
- Repeat (See pages 15 to 16)
- EZ View (See pages 16 to 17)
- Angle (See pages 18)
1. Press the REPEAT button on the remote control.
Repeat screen appears.
Menu
Note
- Depending on a disc, the Title Menu may not
work.
- Title Menu will only be displayed if there are at
least two titles in the disc.
2. Press the ¥/Š buttons to select Chapter, Title or A-B,
then press the ENTER button.
- DVD repeats play by chapter or title.
- Chapter ( ): repeats the chapter that is playing.
- Title ( ): repeats the title that is playing.
- A-B: repeats a segment of the disc that you select.
T
DVD
Off
01
T
01 A - B
ENTER REPEAT
15
English
1. Press the MENU button during playback.
1. During the playback of a DVD disc, press the MENU button
on the remote control.
Using the A-B Repeat function
1. Press the REPEAT button on the remote control.
2. Press the ¦/‹ buttons to select A-B button.
3. Press the ENTER button at the point where you
want repeat play to start (A). B is automatically highlighted.
4. Press the ENTER button at the point where you
want the repeat play to stop (B).
- To return to normal play, press the CANCEL button.
3. To return to normal play, press REPEAT button again, then
press the ¦/‹ buttons to select Off and press ENTER
button.
DVD
Off
01
T
01 A - B
ENTER REPEAT
Note
- A-B REPEAT allows you to set point (B) until at
least 5 seconds of play back time has elapsed
after point (A) has been set.
- Depending on a disc, the Repeat function may
not work.
ADVANCED
FUNCTIONS
Adjusting the Aspect Ratio
(EZ View)
To play back using aspect ratio
(DVD)
Press the EZ VIEW button.
- The screen size changes when the button is pressed
repeatedly.
- The screen zoom mode operates differently depending on the
screen setting in the Display Setup menu.
- To ensure correct operation of the EZ VIEW button, you
should set the correct aspect ratio in the Display Setup
menu. (See pages 25 to 26).
4:3 Letter Box
EZ VIEW
Slow Play
This feature allows you slowly to repeat scenes containing sports, dancing, musical instruments being
played etc., so you can study them more closely.
When playing a DVD
1. During play, press the PAUSE ( ) button.
2. Press the SEARCH (
) button to choose the play
/
speed between 1/8, 1/4 and 1/2 of normal during PAUSE or
STEP mode.
If you are using a 16:9 TV
For 16:9 aspect ratio discs
- WIDE SCREEN
Displays the content of the DVD title in 16:9 aspect ratio.
- SCREEN FIT
The top and bottom portions of the screen are cut off.
When playing a 2.35:1 aspect ratio disc, the black bars at
the top and bottom of the screen will disappear. The picture
will look vertically stretched. (Depending on a type of disc,
the black bars may not disappear completely.)
- ZOOM FIT
The top, bottom, left and right of the screen are cut off and
the central portion of the screen is enlarge
For 4:3 aspect ratio discs
- Normal Wide
Displays the content of the DVD title in 16:9 aspect ratio.
The picture will look horizontally stretched.
- SCREEN FIT
The top and bottom portions of the screen are cut off and
the full screen appears.
The picture will look vertically stretched.
- ZOOM FIT
The top, bottom, left and right portions of the screen are
cut off and the central portion of the screen is enlarged.
- Vertical Fit
When a 4:3 DVD is viewed on a 16:9 TV, black bars will
appear at the left and right of the screen in order to prevent
the picture from looking horizontally stretched.
16
For 16:9 aspect ratio discs
- 4:3 Letter Box
Displays the content of the DVD title in 16:9 aspect ratio. The
black bars will appear at the top and bottom of the screen.
- 4:3 Pan Scan
The left and right portions of the screen are cut off and the
central portion of the 16:9 screen is displayed.
- SCREEN FIT
The top and bottom portions of the screen are cut off and a
full screen appears. The picture will look vertically stretched.
- ZOOM FIT
The top, bottom, left and right of the screen are cut off and
the central portion of the screen is enlarged.
For 4:3 aspect ratio discs
- Normal Screen
Displays the content of the DVD title in 4:3 aspect ratio.
- SCREEN FIT
The top and bottom portions of the screen are cut off and the
full screen appears. The picture will look vertically stretched.
- ZOOM FIT
The top, bottom, left and right portions of the screen are cut
off and the central portion of the screen is enlarged.
Note
- This function depends on audio languages are
encoded on the disc and may not work.
- A DVD disc can contain up to 8 audio languages.
- To have the same audio language come up
whenever you play a DVD;
Refer to “Using the Audio Language” on page 24.
Selecting the Subtitle
Language
You can select a desired subtitle quickly and
easily with the SUBTITLE button.
Using the SUBTITLE button
(DVD/MPEG4)
1. Press the SUBTITLE button. The subtitle languages are
represented by abbreviations.
The subtitle changes when DVD
the button is pressed
Off
repeatedly.
SUBTITLE
Note
This function may behave differently depending on
the type of disc.
External subtitle option will
appear, depends the DivX
Disc.
Selecting the Audio
Language
MPEG4
Subtitle Selection
External Subtitle Off
readme.TXT
Non-standard fonts are not supported
You can select a desired audio language quickly and
easily with the AUDIO button.
Using the AUDIO button
(DVD/MPEG4)
1. Press the AUDIO button. The Audio changes when the
button is pressed repeatedly.
The audio languages are DVD
represented by
ENG DOLBY DIGITAL 5.1CH
abbreviations.
AUDIO
Press AUDIO button at
remocon repeatedly to
select the desired Audio
on MPEG4 then press
the ENTER .
MPEG4
PCM 1/2
AUDIO
2. To remove the AUDIO icon, press the CANCEL or RETURN
button.
Enter
Press SUBTITLE button
at remocon repeatedly to
select the desired subtitle language on a
MPEG4 then press the
ENTER .
Return
Menu
MPEG4
Off
SUBTITLE
2. To remove the SUBTITLE icon, press the CANCEL or
RETURN button.
Note
- You have to change the desired subtitle in the
Disc Menu, according to discs. Press the DISC
MENU button.
- This function depends on what subtitles are
encoded on the disc and may not work on all DVDs.
- A DVD disc can contain up to 32 subtitle
languages.
- To have the same subtitle language come up
whenever you play a DVD; Refer to “Using the
Subtitle Language” on page 24.
17
English
If you are using a 4:3 TV
Changing the Camera
Angle
Using the Bookmark
Function
When a DVD contains multiple angles of a particular
scene, you can use the ANGLE function.
Using the ANGLE function (DVD)
If the disc contains multiple angles, the ANGLE
appears on the screen.
This feature lets you bookmark sections of a DVD
so you can quickly find them at a later time.
1. During play or pause mode, press the MENU button on the
remote control.
2. Press the ›/‚ buttons to select Function, then press the
Š or ENTER button.
3. Press the ›/‚ buttons to select Angle, then press the
Š or ENTER button.
1. During play, press the MENU button on the remote control.
2. Press the ›/‚ buttons to select Function, then press the
Š or ENTER button.
Using the Bookmark Function
(DVD)
Info
Zoom
Bookmark
Repeat
Info
EZ View
Zoom
Angle
Bookmark
Enter
Repeat
Return
Menu
EZ View
Angle
Enter
Return
Menu
3. Press the ›/‚ buttons to select Bookmark, then press the
Š or ENTER button.
4. Press the ¥/Š buttons or you can use the number buttons
on the remote control to select the desired angle.
- - -
4/6
Note
- If the disc has only one angle, this feature won’t
work. Currently, very few discs have this feature.
- Depending on the disc, these functions may not
work.
Using the Instant
Replay/Skip Function
Using the Instant Replay function
(DVD)
If you miss a scene, you can see it again using this
function.
If you press the INSTANT REPLAY button, the current scene
moves backward about 10 seconds, and plays back.
4. When you reach the scene you want to mark, press the
ENTER button. Up to three scenes may be marked at a time.
1 - -
Note
- Depending on a disc, the Bookmark
function may not work.
Recalling a Marked Scene
1~3. The first 1~3 steps are the same as those for “Using the
Bookmark Function”.
4. Press the ¥/Š buttons to select a marked scene.
1 2 3
Using the Instant Skip function
(DVD)
Use this function to skip playback about 10 seconds
ahead of the current scene.
Press the INSTANT SKIP button.
- Playback will skip ahead 10 seconds.
Note
Depending on the disc, these functions may not
work.
18
CANCEL
5. Press the PLAY (
CANCEL
) button to skip to the marked scene.
Clearing a Bookmark
1~3. The first 1~3 steps are the same as those for “Using the
Bookmark Function”.
4. Press the ¥/Š buttons to select the bookmark number you
want to delete.
5. Press the CANCEL button to delete a bookmark number.
1 2 3
-
: Name of currently playing file.
-
: Current Playback Time.
CANCEL
-
: Current Playback Mode : There are four
modes. They can be selected in order by
Using the Zoom Function
pressing the REPEAT button.
Using the Zoom Function (DVD)
English
- Off: Normal Playback
- Track: Repeats the current track.
1. During play or pause mode, press the MENU button on the
remote control.
2. Press the ›/‚ buttons to select Function, then press the
Š or ENTER button.
3. Press the ›/‚ buttons to select Zoom, then press the
Š or ENTER button.
4. Press the ›/‚ or ¥/Š buttons to select the part of the
screen you want to zoom in on. Press the ENTER button.
- During DVD play, press ENTER to zoom in
2X/4X/2X/Normal in order.
- Random: Files in the disc will be played in
random order.
-
: MP3 file icon.
-
: CD Audio file icon.
-
: WMA file icon.
-
: Folder icon.
-
: JPEG file icon
-
: Current Folder icon.
-
: AVI file icon.
Note
- When playing MP3, WMA or JPEG, the Picture
Quality and the HDMI Resolution cannot be set.
- When playing MPEG4 file, the VIDEO SEL. only
work in stop mode.
Info
Zoom
Bookmark
Repeat
EZ View
Angle
Enter
- Folder: Repeats the current folder
Return
Folder Selection
Menu
The folder can be selected both in Stop or Play mode.
- To select the Parent Folder
Press the RETURN button to go to parent folder, or press the
›/‚
‚ buttons to select “..” and press ENTER to go to the
parent folder.
- To select the Peer Folder
‚ buttons to select the desired folder, then
Press the ›/‚
press ENTER.
Clips Menu for MP3/WMA/
JPEG/ MPEG4/CD Audio
CD Audio or discs with MP3/WMA/JPEG contain
individual songs and/or pictures that can be organized into folders as shown below. They are similar
to how you use your computer to put files into different folders.
- To select the Sub-Folder
‚ buttons to select the desired folder,
Press the ›/‚
then press ENTER.
Root
WMA
JPEG
MP3
Parent Folder
MUSIC
Open the disc tray.
Place the disc on the tray.
Close the tray.
The tray closes and this
screen displays.
Stop
Current Folder
Off
T
1st
00:00:00
Sub-Folders
2nd
WMA
JPEG
MP3
SONG FILE 1
MPEG4
Peer Folders
SONG FILE 2
Enter
Return
Menu
SONG FILE 3
MPEG4 FILES
19
MP3/WMA/CD Audio
Playback
1. Open the disc tray. Place the disc on the tray. Close the tray.
- Only one kind of file is played back when a disc or a
folder contains both MP3 and WMA files.
‚ buttons to select a song file.
2. Press the ›/‚
Press ENTER to begin playback of the song file.
Play
Off
B e c a u s e Yo u
T
00:00:23
...
B e c a u s e Yo u
Cactus
Sad Dayu
Wonderful
Enter
Return
REPEAT
Repeat
Repeat/Random playback
Press the REPEAT button to change the playback mode. There
are four modes, such as Off, Track, Folder and Random.
- Off: Normal Playback
- Track: Repeats the current song file.
- Folder: Repeats the song files which have the same
extension in the current folder.
- Random: Song files which have the same extension will be
played in random order.
To resume normal play, press the CANCEL button.
CD-R MP3/WMA file
When you record MP3 or WMA files on CD-R, please refer
to the following.
- Your MP3 or WMA files should be ISO 9660 or JOLIET
format.
ISO 9660 format and Joliet MP3 or WMA files are
compatible with Microsoft's DOS and Windows, and with
Apple's Mac. This format is the most widely used.
- When naming your MP3 or WMA files, do not exceed 8
characters, and enter “.mp3, .wma” as the file extension.
General name format : Title.mp3. or Title.wma. When
composing your title, make sure that you use 8 characters or
less, have no spaces in the name, and avoid the use of
special characters including: (.,/,\,=,+).
- Use a decompression transfer rate of at least 128 Kbps
when recording MP3 files.
Sound quality with MP3 files basically depends on the rate of
compression/decompression you choose. Getting CD audio
sound requires an analog/digital sampling rate, that is
conversion to MP3 format, of at least 128 Kbps and up to 160
Kbps. However, choosing higher rates, like 192 Kbps or more,
only rarely give better sound quality. Conversely, files with
decompression rates below 128 Kbps will not be played
properly.
20
- Use a decompression transfer rate of at least 64Kbps
when recording WMA files.
Sound quality with WMA files basically depends on the rate of
compression/decompression you choose.
Getting CD audio sound requires an analog/digital sampling
rate, that is conversion to WMA format, of at least 64Kbps
and up to 192Kbps. Conversely, files with decompression
rates below 64Kbps or over 192Kbps will not be played
properly.
- Do not try recording copyright protected MP3 files.
Certain "secured" files are encrypted and code protected to
prevent illegal copying. These files are of the following types:
TM
Windows Media (registered trade mark of Microsoft Inc) and
TM
SDMI (registered trade mark of The SDMI Foundation). You
cannot copy such files.
- Important:
The above recommendations cannot be taken as a
guarantee that the DVD player will play MP3 recordings, or as
an assurance of sound quality. You should note that certain
technologies and methods for MP3 file recording on CD-Rs
prevent optimal playback of these files on your DVD player
(degraded sound quality and in some cases, inability of the
player to read the files).
- This unit can play a maximum of 500 files and 500 folders
per disc.
MPEG4 Playback
MPEG4 Play Function
AVI files are used to contain the audio and video data. Only
AVI format files with the “.avi” extensions can be played.
1. Open the disc tray. Place the disc on the tray.
Close the tray.
‚ or ¥/Š
Š buttons to select an avi file
2. Press the ›/‚
(DivX/XiviD) and then press ENTER button.
Stop
Off
/MPEG4
T
00:00:00
...
a01_divx51b-8
a02_divx505b-8
a03_divx502sp-8
a04_divx412-8
Enter
Return
Menu
Repeat playback
Press the REPEAT button to change playback mode. There are
3 modes, such as Off, Folder and Title.
- Folder : repeats the AVI files which have the same extension
in the current folder.
- Title : repeats the title that is playing.
Press the REPEAT A-B button to set the point where you want
repeat play to start (A).
Press the REPEAT A-B button again at the point where you
want the repeat play to stop (B).
- To return to normal play, press the CANCEL button.
Note
- A-B REPEAT does not allow you to set point (B)
until at least 5 second of playback time has
elapsed after point (A) has been set
DivX3.11 & DivX4 & XviD
DivX5
Bitrate may fluctuate:
Device may skip decoding
the high bitrate portions
and begin decoding again
when Bitrate returns to
normal.
720 x 480 @30fps
720 x 576 @25fps
: Maximum bitrate : 4Mbps
Possible warning messages that may appear when trying to
play DivX/AVI files are :
1. No Authorization
- File with bad registration code.
MPEG4 Function Description
Authorization Error
(
Function
Description
Skip
or
During play, press the
or
button, it moves forward
or backward 5 minutes.
During play, press the SEARCH
(
or
) button and press
again to search at a faster
speed. Allows you to search
at a faster speed in an AVI
file. (2X, 4X, 8X)
Allows you to search at a
slower speed in an AVI file.
(1/8X, 1/4X, 1/2X)
Each time the STEP button
is pressed, a new frame will
appear.
)
Search
(
or
)
Slow Motion
Play
Step Motion
Play
Reference page
This player is not authorized
to play this video
-
OK
Enter
Return
-
P 13
2. Unsupported Codec
- Files with certain Codec Types, Versions
(ex. MP4, AFS and other proprietary codecs) are not
suppoerted by this player.
NO CODEC
Stop
Off
S w e e t Vo l 3
P 13
T
00:00:20
...
B e c a u s e Yo u
Cactus
ZOOM
2X/4X/2X/Normal in order
P 19
Sad Dayu
Wo n d e r f u l
S w e e t Vo l 3
- These functions may not work depending on MPEG4 file.
CD-R AVI file
This unit can play the following video compression formats
within the AVI file format:
- DivX 3.11 contents
- DivX 4 contents (Based on MPEG-4 Simple Profile)
- DivX 5 contents (MPEG-4 simple profile plus additional
features such as bi-directional frames. Qpel and GMC are
also supported.)
- XviD MPEG-4 compliant Contents.
Enter
Menu
Return
3. Unsupported Resolution
- Files containing resolutions higher than the player’s
specification are not supported.
Stop
NO CODEC
Off
/a01_divx51b-8
T
00:00:00
...
a01_divx51b-8
a02_divx505b-8
a03_divx502sp-8
a04_divx412-8
Enter
Return
Menu
DVD-RW & DVD+R
Format that support for DivX file :
- Basic DivX format DivX3.11 / 4.12/ 5.x
- Xvid (MPEG-4 compliant video codec) and DivX Pro
- File format : *.avi, *.div, *.divx.
Note
• The resolution that can be supported by DVD1080P8 model up to 720 x 480 @30 frames/ 720 x
576 @25 frames
• This unit supports CD-R/RW written in MPEG4 in
accordance with the “ISO9660 format”.
21
English
This unit supports all resolutions up to maximum below.
Repeat A-B playback
Picture CD Playback
MP3-JPEG Playback
You can play JPEG using music as a backgound.
1. Select the desired folder.
‚ buttons to select a Picture file in the clips
2. Press the ›/‚
menu and then press the ENTER button.
3. Press the INFO button on the remote control to select the
menu you want to view and then press the ENTER button.
ENTER RETURN
‚ buttons to select an MP3 file in the clips
1. Press the ›/‚
menu and then press the ENTER button.
‚ buttons to select a JPEG file in the
2. Press the ›/‚
clips menu and then press the ENTER button.
- Music willplay from the beginning
3. Press Stop button when you want to stop the
playback.
Note
MP3 and JPEG files have to be on the same disc.
Note
- Press the STOP button to return to the clips menu.
- When playing a Kodak Picture CD, the unit
displays the Photo directly, not the clips menu.
Rotation
: Each time the ENTER button is pressed, the
picture rotates 90 degrees clockwise.
Zoom
‚ buttons to select the part of the
: Press the ›/‚
screen you want to zoom in on.
Press the ENTER button. Each time the ENTER button is pressed, the picture is enlarged up to 2X.
Slide Show
•
: The unit enters slide show mode.
• Before beginning the Slide Show, the picture interval must
be set.
•
: When this icon is selected and ENTER is
pressed, the pictures change automatically
with about a 6 second interval.
•
: The pictures change automatically with
about a 12 second interval.
•
: The pictures change automatically with
about a 18 second interval.
TIMER:
ENTER RETURN
Note
- Depending on a file size, the amount of time
between each picture may be different from the
manual.
- If you don’t press any button, the slide show will
start automatically in about 10 seconds by default.
22
CD-R JPEG Disc
- Only files with the “.jpg” and “.JPG” extensions can be played.
- If the disc is not closed, it will take longer to start playing and
not all of the recorded files may be played.
- Only CD-R discs with JPEG files in ISO 9660 or Joliet format
can be played.
- The name of the JPEG file may not be longer than 8
characters and should contain no blank spaces or special
characters (. / = +).
- Only a consecutively written multi-session disc can be played.
If there is a blank segment in the multi-session disc, the disc
can be played only up to the blank segment.
- A maximum of 3000 images can be stored on a single CD.
- Kodak Picture CDs are recommended.
- When playing a Kodak Picture CD, only the JPEG files in the
pictures folder can be played.
- Kodak Picture CD: The JPEG files in the pictures folder can
be played automatically.
- Konica Picture CD: If you want to see the Picture, select the
JPEG files in the clips menu.
- Fuji Picture CD: If you want to see the Picture, select the
JPEG files in the clips menu.
- QSS Picture CD: The unit may not play QSS Picture CD.
- If the number of files in 1 Disc is over 500, only 500 JPEG
files can be played.
- If the number of folders in 1 Disc is over 500, only JPEG
files in 500 folders can be played
Setting Up the Language
Features
CHANGING SETUP
MENU
If you set the player menu, disc menu, audio and subtitle
language in advance, they will come up automatically every
time you watch a movie.
Using the Setup Menu
1. With the unit in Stop mode, press the MENU button on the
‚ buttons to select Setup, then
remote control. Use the ›/‚
press the Š or ENTER button.
Š
Language Setup
Š
Audio Setup
Display Setup
Š
Parental Setup :
Š
DivX(R) Registration
Š
Anynet+(HDMI-CEC):On
Enter
Return
LANGUAGE SETUP
Menu
❶ Language Setup: Setup of the Language.
❷ Audio Setup : Setup of the Audio Options.
❸ Display Setup : Setup of the Display Options. Use to
select which type of screen you want to
watch and several display options.
❹ Parental Setup : Setup of the Parental Level. Allows
users to set the level necessary to
prevent children from viewing unsuitable
movies such as those with violence,
adult subject matter, etc.
❺ Divx(R) Registration : Please use the Registration code
to register this player with the
DivX(R) Video On Demand
format. To learn more go to
www.divx.com/vod.
❻ Anynet+(HDMI-CEC): Setup of the Anynet+(HDMI-CEC)
Options.
‚ buttons to access the different features.
2. Press the ›/‚
Press the Š or ENTER button to access the sub features.
3. To make the setup screen disappear after setting up, press
the MENU button again.
Note
Depending on the disc, some Setup Menu
selections may not work.
1. With the unit in Stop mode, press the MENU button.
‚ buttons to select Setup, then press the Š
2. Press the ›/‚
or ENTER button.
‚ buttons to select Language Setup, then
3. Press the ›/‚
press the Š or ENTER button.
‚ buttons to select Player Menu, then press
4. Press the ›/‚
the Š or ENTER button.
‚ buttons to select the desired language,
5. Press the ›/‚
then press the Š or ENTER button.
- The language is selected and the screen
returns to Language Setup menu.
- To make the setup menu disappear, press the MENU
button.
Player Menu
Menu
Player
Disc Menu
Audio
Subtitle
DivX Subtitle
Enter
: English
√ English
Français
Deutsch
Español
Italiano
Nederlands
Return
Menu
Using the Disc Menu Language
This function changes the text language only on the disc
menu screens.
1. With the unit in Stop mode, press the MENU button.
‚ buttons to select Setup, then press the Š
2. Press the ›/‚
or ENTER button.
‚ buttons to select Language Setup, then
3. Press the ›/‚
press the Š or ENTER button.
‚ buttons to select Disc Menu, then press
4. Press the ›/‚
the Š or ENTER button.
‚ buttons to select the desired language,
5. Press the ›/‚
then press the Š or ENTER button.
- If the selected language is not recorded on the disc,
the original pre-recorded language is selected.
- The language is selected and the screen returns to
Language Setup menu.
- To make the setup menu disappear, press the MENU
button.
LANGUAGE SETUP
Player Menu
Disc Menu
Audio
Subtitle
DivX Subtitle
Enter
√ English
Français
Deutsch
Español
Italiano
Nederlands
Return
Menu
23
English
Using the Player Menu Language
The Setup menu lets you customize your DVD player by
allowing you to select various language preferences, set up
a parental level, even adjust the player to the type of
television screen you have.
Using the DivX Subtitle Language
Using the Audio Language
1. With the unit in Stop mode, press the MENU button.
ƒ buttons to select Setup, then press the ‹
2. Press the œ/ƒ
or ENTER button.
ƒ buttons to select Language Setup, then
3. Press the œ/ƒ
press the ‹ or ENTER button.
ƒ buttons to select Audio, then press the ‹
4. Press the œ/ƒ
or ENTER button.
ƒ buttons to select the desired language, then
5. Press the œ/ƒ
press the ‹ or ENTER button.
- Select “Original” if you want the default soundtrack
language to be the original language the disc is
recorded in.
- If the selected language is not recorded on the disc, the
original pre-recorded language is selected.
- The language is selected and the screen returns to
Language Setup menu.
- To make the setup menu disappear, press the
MENU button.
LANGUAGE SETUP
Player Menu
Disc Menu
Audio
Subtitle
DivX Subtitle
Enter
Original
√ English
Français
Deutsch
Español
Italiano
Return
Menu
Using the Subtitle Language
1. With the unit in Stop mode, press the MENU button.
ƒ buttons to select Setup, then press the ‹
2. Press the œ/ƒ
or ENTER button.
ƒ buttons to select Language Setup, then
3. Press the œ/ƒ
press the ‹ or ENTER button.
ƒ buttons to select Subtitle, then press the ‹
4. Press the œ/ƒ
or ENTER button.
ƒ buttons to select the desired language,
5. Press the œ/ƒ
then press the ‹ or ENTER button.
- Select “Automatic” if you want the subtitle language to
be the same as the language selected as the audio
language.
- Some discs may not contain the language you select as
your initial language; in that case the disc will use its
original language setting.
- The language is selected and the screen returns to
setup menu.
- To make the setup menu disappear, press the MENU
button.
LANGUAGE SETUP
Player Menu
Disc Menu
Audio
Subtitle
DivX Subtitle
Enter
24
√ Automatic
English
Français
Deutsch
Español
Italiano
Return
Menu
1. With the unit in Stop mode, press the MENU button.
ƒ buttons to select Setup, then press the ‹
2. Press the œ/ƒ
or ENTER button.
ƒ buttons to select Language Setup, then
3. Press the œ/ƒ
press the ‹ or ENTER button.
ƒ buttons to select DivX Subtitle, then press
4. Press the œ/ƒ
the ‹ or ENTER button.
ƒ buttons to select the desired language,
5. Press the œ/ƒ
then press the ‹ or ENTER button.
- The language is selected and the screen returns to
Language Setup menu.
- To make the setup menu disappear, press the
MENU button.
LANGUAGE SETUP
Player Menu
: English
√ Unicode
Disc Menu
Western
Audio
Turkish
Subtitle
Central
DivX Subtitle
Cyrillic
Greek
Enter
Return
Menu
Setting Up the Audio
Options
Audio Options allows you to setup the audio device
and sound status settings depending on the audio
system in use.
1. With the unit in Stop mode, press the MENU button.
ƒ buttons to select Setup, then press the ‹
2. Press the œ/ƒ
or ENTER button.
ƒ buttons to select Audio Setup, then press
3. Press the œ/ƒ
the ‹ or ENTER button.
ƒ buttons to select the desired item, then
4. Press the œ/ƒ
press the ‹ or ENTER button.
Language Setup
‹
Audio Setup
‹
Display Setup
‹
Parental Setup :
‹
DivX(R) Registration
‹
Anynet+(HDMI-CEC):On
Enter
Return
Menu
AUDIO SETUP
Digital Out
: PCM
MPEG-2 Digital Out
: PCM
Dynamic Compression : On
PCM Down Sampling
Enter
Return
: On
Menu
❶ Digital Out
- PCM : Converts to PCM(2CH) audio.
- Bitstream : Outputs Dolby Digital via the digital
output. Select Bitstream when connecting to a
Dolby Digital Decoder.
Note :
- There is no analog audio output when you play
a DTS sound disc.
- Even when PCM Down sampling is Off
• Some discs will only output down sampled
audio through the digital outputs.
• To make the Setup menu disappear, press the
MENU button.
Language Setup
‹
Audio Setup
‹
Display Setup
‹
Parental Setup :
‹
DivX(R) Registration
‹
Anynet+(HDMI-CEC):On
Enter
Return
Depending on a type of television you have, you may want
to adjust the screen setting (aspect ratio).
- 4:3 Letter Box : Select when you want to see the total
16:9 ratio screen DVD supplies, even though you
have a TV with a 4:3 ratio screen. Black bars will
appear at the top and bottom of the screen.
- 4:3 Pan&Scan : Select this for conventional size TVs
when you want to see the central portion of the 16:9
screen. (Extreme left and right side of movie picture
will be cut off.)
- 16:9 Wide : You can view the full 16:9 picture on your
wide screen TV.
DISPLAY SETUP
Aspect
Ratio
TV Aspect
HDMI
- If your TV is not compatible with compressed multichannel formats (Dolby Digital, DTS, MPEG), you
should set Digital Audio to PCM.
- If your TV is not compatible with LPCM sampling
rates over 48kHz, you should set PCM Down sampling to On.
Menu
❶ TV Aspect
: 16:9 Wide
Still Mode
Screen Message
TV System
Video Output
HDMI
Picture Quality
Enter
√ 4:3 Letter Box
4:3 Pan&Scan
16:9 Wide
: SCART RGB
‹
‹
Return
Menu
❷ Still Mode
These options will help prevent picture shake in still
mode and display small text clearer.
- Auto : When selecting Auto, Field/Frame mode will be
automatically converted.
Manufactured under license from Dolby
Laboratories. “Dolby” and the double-D symbol
are trademarks of Dolby Laboratories.
- Field : Select this feature when the screen shakes in
the Auto mode.
“DTS” and “DTS Digital Out” are trademarks of
Digital Theater Systems, Inc.
- Frame : Select this feature when you want to see
small letters more clearly in the Auto mode.
❸ Screen Messages
Setting Up the Display
Options
Display options enable you to set various video functions of
the player.
1. With the unit in Stop mode, press the MENU button.
ƒ buttons to select Setup, then press the ‹
2. Press the œ/ƒ
or ENTER button.
ƒ buttons to select Display Setup, then
3. Press the œ/ƒ
press the ‹ or ENTER button.
ƒ buttons to select the desired item, then
4. Press the œ/ƒ
press the ‹ or ENTER button.
Use to turn on-screen messages On or Off.
❹ TV System
- NTSC : In case of using NTSC disc
• If your TV system only has PAL-Video input, you must
choose “PAL”. When you choose “PAL”, Interlace output format is PAL 60 Hz output.
• If your TV system only has NTSC, input you must
choose “NTSC ”.
• If you set up the NTSC TV, HDMI output frame rate is 60 Hz.
- PAL : In case of using PAL disc
• If your TV system only has NTSC-Video input, you
must choose “NTSC”.
• If your TV system only has PAL input, you must
choose “PAL ”.
• If you set up the PAL TV, HDMI output frame rate is 50 Hz .
25
English
❷ MPEG-2 Digital Out
- PCM : Converts to PCM(2CH) audio.
- Bitstream : Converts to MPEG-2 Digital Bitstream
(5.1CH or 8CH). Select Bitstream when using the
Digital Audio Output.
❸ Dynamic Compression
- On : To select dynamic compression.
- Off : To select the standard range.
❹ PCM Down Sampling
- On : Select this when the Amplifier connected to the
player is not 96KHz compatible. In this case, the
96KHz signals will be down converted to 48KHZ.
- Off : Select this when the Amplifier connected to the
player is 96KHz compatible. In this case, all signals will
be output without any changes.
DISPLAY SETUP
TV Aspect
: 4:3 L-Box
Still Mode
: Auto
Screen Messages
: On
TV System
- Black Level : Adjusts the brightness of the screen.(On
or Off) It does not function in Progressive mode.
NTSC
√ PAL
Video Output
❼ Picture Quality
HDMI
‹
Picture Quality
‹
- Brightness : Level 1 ~ Level 5
- Contrast : Level 1 ~ Level 5
Enter
Return
Menu
- Color Saturation : Level 1 ~ Level 5
❺ Video Output
Select Video Output.
- P-SCAN : Select when you want to use Component
Progressive (525p) Out.
- SCART-CVBS : Select when you want to CVBS output
from scart connection.
- SCART RGB Output : Select when you want to use
Scart Out.
PICTURE QUALITY
Black Level
: Off
Brightness
: Level 3
Contrast
: Level 3
Color Saturation
: Level 3
Enter
Return
Menu
• If you press the VIDEO SEL. button, Video output
mode is changed in regular sequence in no disc
mode. (P-SCAN ➝ SCART CVBS ➝ SCART RGB)
• If the Yes/No selection in the Display Setup sub
Menu is not made within 10 seconds, the screen
returns to the previous menu.
❻ HDMI
This setting is used when the unit is connected by HDMI
to Display devices (TV, Projector, etc.).
- Resolution Setting
- Auto : Resolution setting automatically
- Manual : Resolution setting manually
- Resolution
• 480p/576p : 720 x 480, 720 x 480
• 720p : 1280 x 720
• 1080i : 1920 x 1080
• 1080p : 1920 x 1080
HDMI SETUP
Resolution Setting
: Manual
Resolution
: 720p
Enter
26
Return
Menu
• Consult your TV User’s Manual to find
out if your TV supports Progressive Scan. If
Progressive Scan is supported, follow the
TV User’s Manual regarding Progressive
Scan settings in the TV’s menu system.
• If Video Output is set incorrectly, the screen
may be blocked.
• The resolutions available for HDMI output
depend on the connected TV or projector.
For details, see the user’s manual of your
TV or projector.
• When the resolution is changed during playback, it may take a few seconds for a normal image to appear.
• If you set the HDMI output resolution 720p,
1080p or 1080i, HDMI output provides better
picture quality.
Setting Up the Parental
Control
To make the setup menu disappear, press the MENU
button. For example, if you select up to Level 6, discs
that contain Level 7,8 will not play.
1. With the unit in Stop mode, press the MENU button.
ƒ buttons to select Setup, then press the ‹
2. Press the œ/ƒ
or ENTER button.
Changing the Password
1. With the unit in Stop mode, press the MENU button.
ƒ buttons to select Setup, then press the ‹
2. Press the œ/ƒ
or ENTER button.
Language Setup
‹
Audio Setup
‹
Display Setup
‹
Parental Setup :
‹
‹
DivX(R) Registration
‹
‹
Parental Setup :
Anynet+(HDMI-CEC):On
DivX(R) Registration
‹
Language Setup
‹
Audio Setup
‹
Display Setup
Enter
Return
Menu
Anynet+(HDMI-CEC):On
Enter
Return
Menu
ƒ buttons to select Parental Setup, then
3. Press the œ/ƒ
press the ‹ or ENTER button.
ƒ buttons to select Parental Setup, then
3. Press the œ/ƒ
press the ‹ or ENTER button.
Language Setup
‹
Language Setup
‹
Audio Setup
‹
Audio Setup
‹
Display Setup
‹
Display Setup
‹
Parental Setup :
‹
Parental Setup :
‹
DivX(R) Registration
‹
DivX(R) Registration
Anynet+(HDMI-CEC):On
Enter
Return
Menu
ƒ buttons to select Rating Level, then press
4. Press the œ/ƒ
the ‹ or ENTER button.
PARENTAL SETUP
Rating Level
‹
Anynet+(HDMI-CEC):On
Enter
Return
Menu
ƒ button to select Change Password, then
4. Press the œ/ƒ
press the ‹ or ENTER button. Enter your new password.
Re-enter the new password again.
: Kids Safe
PARENTAL SETUP
Change Password
Rating Level
:Kids Safe
Change Password
Enter
Return
Menu
5. Enter your password.
- By default, password is set to 0000. Please change
password to other than 0000 to activate parental
control function.
Enter
Return
Menu
PARENTAL SETUP
Rating Level
:Kids Safe
Change Password
PARENTAL SETUP
Rating Level
Enter Password
: Kids Safe
Change Password
Enter Password
Enter
Return
Menu
PARENTAL SETUP
Enter
Return
Menu
Rating Level
ƒ buttons to select the Rating Level you want,
6. Press the œ/ƒ
then press the ‹ or ENTER button.
e.g) Setting up in Kids Safe.
:Kids Safe
Change Password
Enter New Password
PARENTAL SETUP
Rating
RatingLevel
Level
: Kids Safe
Change Passwor
Enter
Return
√ Kids Safe
Level 2
Level 3
Level 4
Level 5
Level 6
Enter
Return
Menu
Note
If you have forgotten your password, see
“Forgot Password” in the Troubleshooting Guide.
Menu
27
English
The Parental Control function works in conjunction
with DVDs that have been assigned a rating, which
helps you control the types of DVDs that your family
watches. There are up to 8 rating levels on a disc.
Setting Up the Rating Level
Setting Up the
Anynet+(HDMI-CEC)
Note
To make the Setup menu disappear, press the
MENU button.
Anynet+ is a function that can be used to operate
the unit using a Samsung TV remote control, by
connecting the DVD 1080P8 to a SAMSUNG TV
using a HDMI Cable. (see page 12) (This is only
available with SAMSUNG TVs that support
Anynet+).
• You can operate the DVD Player by using TV
remote control. (TV buttons that can be used to con
trol the DVD Player :
,
,
,
,
,
Select On when you connecting the DVD 1080P8
with Samsung TV that support Anynet+.
Language Setup
‹
Audio Setup
‹
Display Setup
‹
Parental Setup :
‹
DivX(R) Registration
‹
Anynet+(HDMI-CEC):On
Return
Menu
ƒ buttons to select Anynet+(HDMI-CEC),
3. Press the œ/ƒ
then press the ‹ or ENTER button.
Language Setup
‹
Audio Setup
‹
Display Setup
‹
Parental Setup :
‹
DivX(R) Registration
‹
Anynet+(HDMI-CEC):On
Enter
Return
Menu
4. Set the Anynet+(HDMI-CEC) to “On” on your DVD Player,
then press the ‹ or ENTER button.
Language Setup
‹
Audio Setup
‹
Display Setup
‹
Parental Setup :
‹
DivX(R) Registration
Off
Anynet+(HDMI-CEC):On
√ On
‹
Enter
Return
Menu
5. Set the Anynet+ function at your TV. (See the TV instruction
manual for more information.).
• When you press Anynet+ button on the TV remote
control, the below OSD will appear.
DVDP
View TV
®
Select Device
®
Record
®
Menu on Device
®
Device Operation
®
Receiver : Off
®
Setup
®
Move
Exit
ENTER
TV Menu
28
,and
buttons,
- Select Device : Use this option to select device.
1. With the unit in Stop mode, press the MENU button.
ƒ buttons to select Setup, then press the ‹
2. Press the œ/ƒ
or ENTER button.
Enter
,
buttons.).
- Menu on Device : Same as MENU button on the
DVD Player remote control.
- Device Operation : Same as INFO button on the
DVD Player remote control.
Note
• By pressing the PLAY button of the unit while watching TV, the TV screen will change to the play screen.
• If you play a DVD when the TV power is off, the TV
will power On.
• If you turn the TV off , the DVD Player will power
off automatically.
• If you change the HDMI to other sources
(Composite,Component,... etc) in TV while play
ing the DVD disc, the DVD Player will stop play
ing.
REFERENCE
2. Press the ¦/‹ buttons to select Total, then press the
ENTER button.
Introduction
Samsung will often support the software upgrade to
improve the performance of this unit to the latest
status, through Samsung Internet Site
(www.samsung.com).
Because the specially new mpeg4 codec continues and
it is appearing. What improvements are made depends
on the upgrade software you are using as well as the
software that your DVD-player contained before the
upgrade.
How to make an upgrade disc
Write the downloaded file onto a blank CD-R or CDRW disc, using the following settings:
New Version : 071129V7.B.1080P8XEG
Firmware upgrade starts
- In the middle of the writing, the tray will open
automatically. After taking out the disc, please wait for
about 2 minutes.
- If the unit was succesfully updated, the unit will turn off
and on after closing the tray automatically. When the
unit turns on, this screen will display.
3. Press the number buttons to select the desired language
1. You have to download a new file through Download Center
of Samsung Internet Site (www.samsung.com).
2. Write the file to Disc using CD-RW of your computer.
Note
- File System CD-ROM ISO Level
- Character set ISO 9660
- Finalized, single session
- Write speed low
Upgrade procedure
1. Open the disc tray. Place the disc on the tray. Close the
tray. The Firmware upgrade screen appears.
Press
Touche
Drücken Sie
Pulsar
Premere
Druk op
1
2
3
4
5
6
for English
pour Français
für Deutsch
para Español
per Italiano
voor Nederlands
Note
- If the “Select Menu Language” doesn’t appear,
please contact to “Samsung Service Center”.
- Do not press any button and unplug the power
code during upgrade.
- The upgrade procedure may change, refer to
the web site (www.samsung.com).
Old Version : 071109V1.B.1080P8XEG
New Version : 071129V7.B.1080P8XEG
Firmware upgrade
appears on the display
29
English
Firmware upgrade
Troubleshooting
Before requesting service (troubleshooting), please check the following.
Action
Problem
Page
No operations can be
performed with the
remote control.
• Check the batteries in the remote control.
They may need replacing.
• Operate the remote control at a distance of no more than 20 feet.
• Remove batteries and hold down one or more buttons for several minutes to drain
the microprocessor inside the remote control to reset it. Reinstall batteries and try
to operate the remote control again.
P3
Disc does not play.
• Ensure that the disc is installed with the label side facing up.
• Check the region number of the DVD.
P5
5.1 channel sound is
not being reproduced.
The
icon appears
on screen.
• 5.1 channel sound is reproduced only when the following conditions are met. :
1) The DVD player is connected with the proper Amplifier
2) The disc is recorded with 5.1 channel sound.
• Check whether the disc being played has the “5.1 ch” mark on the outside.
• Check if your audio system is connected and working properly.
• In a SETUP Menu, is the Audio Output set to Bitstream?
• The features or action cannot be completed at this time because:
1. The DVD’s software restricts it.
2. The DVD’s software doesn’t support the feature (e.g., angles).
3. The feature is not available at the moment.
4. You’ve requested a title or chapter number or search time that is out of range.
P11-12
P24~25
Disc Menu doesn’t appear. • Check if the disc has a Menu.
Play mode differs from the • Some of the functions selected in the Setup Menu may not work properly if the
disc is not encoded with the corresponding function.
Setup Menu selection.
P23~28
The screen ratio
cannot be changed.
• The Screen Ratio is fixed on your DVDs.
P25~26
No audio.
• Make sure you have selected the correct Digital Output in the Audio Options
Menu.
P24~25
The screen is blocked
• Press the
button (in front panel) for more than 5 seconds under no disc
inside. All settings will revert to the factory settings.
P13
Forgot password
• Press the
button (in front panel) for more than 5 seconds
under no disc inside. All settings including the password will revert to the factory
settings. Don't use this unless absolutely necessary.
If you experience
other problems.
• Go to the contents and find the section of the instruction book that contains the
explanations regarding the current problem, and follow the procedure once again.
• If the problem still cannot be solved, please contact your nearest authorized service center.
The picture is noisy or
distorted
• Make sure that the disc is not dirty or scratched.
• Clean the disc.
No HDMI output.
• Check the Video output is HDMI enabled.
• Check the connection between the TV and the HDMI jack of DVD player.
• See if the TV supports this 480p/576p/720p/1080i/1080p DVD player.
P10~11
Abnormal HDMI output
screen.
• If snow noise appears on the screen, it means that TV does not support HDCP
(High-bandwidth Digital Content Protection).
P10~11
• Check your TV system setup correctly.
• The screen Jitter phenomenon may occur when frame rate is converted from
50Hz to 60Hz for 720P/1080i/1080p HDMI (High Definition Multimedia Interface)
Output.
• Please refer to the user’s manual of your TV.
P25~26
HDMI output Jitter
30
P27
P2
Specifications
AC 110-240 V, 50/60 Hz
Power Consumption
9W
Weight
Dimensions
1.7 Kg
430mm (W) X 205mm (D) X 45mm (H)
Operating Temperature Range
+5°C to +35°C
Operating Humidity Range
10 % to 75 %
DVD
(DIGITAL VERSATILE DISC)
English
General
Power Requirements
Reading Speed : 3.49 ~ 4.06 m/sec.
Approx. Play Time
(Single Sided, Single Layer Disc) : 135 min.
CD : 12Cm
Disc
(COMPACT DISC)
CD : 8Cm
(COMPACT DISC)
Composite Video
Reading Speed : 4.8 ~ 5.6 m/sec.
Maximum Play Time : 74 min.
Reading Speed : 4.8 ~ 5.6 m/sec.
Maximum Play Time : 20 min.
1 channel : 1.0 Vp-p (75 Ω load)
R(Red) : 0.7 Vp-p (75 Ω load)
G(Green) : 0.7 Vp-p (75 Ω load)
Video
SCART Jack
B(Blue) : 0.7 Vp-p (75 Ω load)
Composite Video : 1.0 Vp-p (75 Ω load)
Output
Luminance Signal : 1.0 Vp-p (75 Ω load)
Color Signal : 0.3 Vp-p (75 Ω load)
HDMI
SCART Jack
2 Channel
Audio
Output
480p, 576p, 720p, 1080p, 1080i
2 Channel : L(1/L), R(2/R)
L(1/L), R(2/R)
48 kHz Sampling : 4 Hz to 22 kHz
*Frequency Response
96 kHz Sampling : 4 Hz to 44 kHz
*S/N Ratio
110 dB
*Dynamic Range
100 dB
*Total Harmonic Distortion
0.004 %
*: Nominal specification
- Samsung Electronics Co., Ltd reserves the right to change the specifications with out notice.
- Weight and dimensions are approximate.
31
UNITED KINGDOM
This Samsung product is warranted for the period of
twelve (12) months from the original date of
purchase, against defective materials and
workmanship. In the event that warranty service is
required, you should return the product to the retailer
from whom it was purchased.
However, Samsung Authorised Dealers and
Authorised Service Centres in other EC Countries
will comply with the warranty on the terms issued to
purchasers in the country concerned.
In case of difficulty, details of our Authorised Service
Centres are available from:
Samsung Electronics U.K. Ltd.
Customer Care Centre
PO Box 17243
Edinburgh, EH11 4YB
United Kingdom
Tel : 0870 SAMSUNG (7267864),
Fax : 0870 7221127 (United Kingdom)
Tel : 0818 717 100,
Fax : +44 (0)870 7221127 (Republic of Ireland)
Web : www.samsung.com/uk
■ WARRANTY CONDITIONS
1. The warranty is only valid if, when warranty service is required, the warranty card is fully and properly completed and is presented with the original
invoice or sales slip or confirmation, and the serial
number on the product has not been defaced.
2. Samsung’s obligations are limited to the repair or,
at its discretion, replacement of the product or the
defective part.
3. Warranty repairs must be carried out by Authorised
Samsung Dealers or Authorised Service Centres.
No re-imbursement will be made for repairs carried
out by non Samsung Dealers and, any such repair
work and damage to the products caused by such
repair work will not be covered by this warranty.
REPUBLIC OF
IRELAND
4. This product is not considered to be defective in
materials nor workmanship by reason that it
requires adaptation in order to conform to national
or local technical or safety standards in force in
any Country other than the one for which the
product was originally designed and manufactured. This warranty will not cover, and no reimbursement will be made for such adaptation nor
any damage which may result.
5. This warranty covers none of the following:
a) Periodic check ups, maintenance and repair or
replacement of parts due to normal wear and
tear.
b) Cost relating to transport, removal or installation
of the product.
c) Misuse, including the faiure to use this product
for its normal purposes or incorrect installation.
d) Damage caused by Lightning, Water, Fire, Acts
of God, War, Public Disturbances, incorrect
mains voltage, improper ventilation or any other
cause beyond the control of Samsung.
6. This warranty is valid for any person who legally
acquired possession of the product during the
warranty period.
7. The consumers statutory rights in any applicable
national legislation whether against the retailer
arising from the purchase contract or otherwise
are not affected by this warranty. Unless there is
national legislation to the contrary, the rights under
this warranty are the consumers sole rights and
Samsung, its subsidiaries and distributors shall not
be liable for indirect or consequential loss or any
damage to records, compact discs, videos or
audio taper or any other related equipment or
material.
SAMSUNG ELECTRONICS (U.K.) LTD.
DVD contact-XEU.indd 1
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer
care center.
Region
North America
Latin America
Country
CANADA
MEXICO
U.S.A
ARGENTINE
BRAZIL
CHILE
NICARAGUA
HONDURAS
COSTA RICA
ECUADOR
EL SALVADOR
GUATEMALA
JAMAICA
PANAMA
PUERTO RICO
REP. DOMINICA
TRINIDAD & TOBAGO
VENEZUELA
COLOMBIA
BELGIUM
CZECH REPUBLIC
DENMARK
FINLAND
FRANCE
Europe
CIS
Asia Pacific
Middle East &
Africa
Customer Care Center 1-800-SAMSUNG(726-7864)
01-800-SAMSUNG(726-7864)
1-800-SAMSUNG(726-7864)
0800-333-3733
0800-124-421 , 4004-0000
800-SAMSUNG(726-7864)
00-1800-5077267
800-7919267
0-800-507-7267
1-800-10-7267
800-6225
1-800-299-0013
1-800-234-7267
800-7267
1-800-682-3180
1-800-751-2676
1-800-SAMSUNG(726-7864)
0-800-100-5303
01-8000112112
0032 (0)2 201 24 18
844 000 844
Distributor pro Českou republiku:
Samsung Zrt., česka organizační složka
Vyskočilova 4, 14000 Praha 4
70 70 19 70
030-6227 515
3260 SAMSUNG ( 0,15/Min),
08 25 08 65 65 ( 0,15/Min)
Web Site
www.samsung.com/ca
www.samsung.com
www.samsung.com
www.samsung.com/ar
www.samsung.com
www.samsung.com/cl
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com.co
www.samsung.com/be
www.samsung.com/cz
www.samsung.com/dk
www.samsung.com/fi
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com/be
www.samsung.com/nl
www.samsung.com/no
www.samsung.com/pl
www.samsung.com/pt
www.samsung.com/sk
www.samsung.com
www.samsung.com/se
www.samsung.com
www.samsung.com/ie
www.samsung.com/at
www.samsung.com/ch
www.samsung.com
www.samsung.kz
www.samsung.uz
GERMANY
HUNGARY
ITALIA
LUXEMBURG
NETHERLANDS
NORWAY
POLAND
PORTUGAL
SLOVAKIA
SPAIN
SWEDEN
U.K
EIRE
AUSTRIA
SWITZERLAND
RUSSIA
KAZAHSTAN
UZBEKISTAN
KYRGYZSTAN
TADJIKISTAN
UKRAINE
LITHUANIA
LATVIA
ESTONIA
AUSTRALIA
NEW ZEALAND
CHINA
HONG KONG
INDIA
INDONESIA
JAPAN
MALAYSIA
PHILIPPINES
SINGAPORE
THAILAND
TAIWAN
VIETNAM
TURKEY
0900-SAMSUNG(726-7864) ( 0,10/Min)
815-56 480
0 801 801 881 , 022-607-93-33
80820-SAMSUNG(726-7864)
0800-SAMSUNG(726-7864)
902 10 11 30
0771-400 200
0845 SAMSUNG (7267864)
0818 717 100
0800-SAMSUNG(726-7864)
0800-SAMSUNG(726-7864)
8-800-555-55-55
8-10-800-500-55-500
8-10-800-500-55-500
00-800-500-55-500
8-10-800-500-55-500
8-800-502-0000
8-800-77777
800-7267
800-7267
1300 362 603
0800SAMSUNG(726-7864)
800-810-5858 , 010-6475 1880
3698-4698
3030 8282 , 1800 110011
0800-112-8888
0120-327-527
1800-88-9999
1800-10-SAMSUNG(726-7864)
1800-SAMSUNG(726-7864)
1800-29-3232 , 02-689-3232
0800-329-999
1 800 588 889
444 77 11
www.samsung.com
www.samsung.lt
www.samsung.com/lv
www.samsung.ee
www.samsung.com
www.samsung.com/nz
www.samsung.com
www.samsung.com/hk
www.samsung.com
www.samsung.com
www.samsung.com/jp
www.samsung.com/my
www.samsung.com/ph
www.samsung.com
www.samsung.com
www.samsung.com/tw
www.samsung.com
www.samsung.com
SOUTH AFRICA
0860-SAMSUNG(726-7864 )
www.samsung.com
U.A.E
800-SAMSUNG (726-7864), 8000-4726
www.samsung.com
01805 - SAMSUNG(726-7864) (
06-80-SAMSUNG(726-7864)
800-SAMSUNG(726-7864)
0035 (0)2 261 03 710
0,14/Min)
Memo
Memo
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products,
please contact the SAMSUNG customer care centre.
☎ 0845 - SAMSUNG(726-7864)/www.samsung.com
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking shown on the product or its literature, indicates that it should not be disposed with other household
wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable
reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government
office, for details of where and how they can take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.
AK68-01503Q
Download PDF