Samsung | DVD-P145 | Samsung DVD-P145 Benutzerhandbuch

DVD Player
Lecteur DVD
DVD-Speler
DVD-P145
AK68-00418G
Precautions
1. Setting up
* Refer to the identification label located on the back
panel of your player for its proper operating voltage.
* Install your player in a cabinet with adequate
ventilation holes. (7~10cm) Do not block ventilation
holes on any of the components for circulation of air.
* Do not push the disc tray by the hand.
* Do not stack components.
* Be sure to turn all components off before moving the
player.
* Before connecting other components to this player, be
sure to turn them off.
* Be sure to remove the disc and turn off the player
after use, especially if you don’t use it for a long time.
2. For your safety
* This product utilizes a laser. Use of controls or
adjustments or performance of procedures other than
those specified herein may result in hazardous
radiation exposure.
* Do not open covers and do not repair yourself.
Refer servicing to qualified personal.
3. Caution
* Your player is not intended for industrial use but for
domestic purposes. Use of this product is for
personal use only.
* Do not put any container filled with liquid or any small
metal objects on the player.
* Exterior influences such as lightning and static
electricity can affect normal operation of this player.
If this occurs, turn the player off and on again with the
POWER button, or disconnect and then reconnect the
AC power cord to the AC power outlet. The player will
operate normally.
* When condensation forms inside the player due to
sharp changes in temperature, the player may not
operate correctly. If this occurs, leave the player at
room temperature until the inside of the player
becomes dry and operational.
4. Disc
* Do not clean record-cleaning sprays, benzene,
thinner, or other volatile solvents that may cause
damage to the disc surface.
* Do not touch the disc’s signal surface. Hold by the
edges or by one edge and the hole in the center.
* Wipe the dirt away gently; never wipe a cloth back
and forth over the disc.
Before you start
CAUTION : USE OF ANY CONTROLS,
ADJUSTMENTS, OR PROCEDURES OTHER
THAN SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
Table of Contents
Setup
Accessories
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Before you start . . . . . . . . . . . . . . . . . . . . . . . .3
General Features . . . . . . . . . . . . . . . . . . . . . . .4
Disc Type and Characteristics . . . . . . . . . . . . .5
Description-Front Panel . . . . . . . . . . . . . . . . . .6
Display Indicators . . . . . . . . . . . . . . . . . . . . . .6
Description-Rear Panel . . . . . . . . . . . . . . . . . .7
Tour of the Remote Control . . . . . . . . . . . . . . .8
1
EZ VIEW
STANDBY/ON
PLAY
LOADING
Remote Control
Batteries for
Remote Control
(AAA Size)
Connections
Choosing a Connection . . . . . . . . . . . . . . . . . .9
Basic Functions
EZ VIEW
STANDBY/ON
PLAY
STANDBY/ON
2
EZ VIEW
PLAY
LOADING
User’s Manual
3
STANDBY/ON
EZ VIEW
Playing a Disc . . . . . . . . . . . . . . . . . . . . . . . .11
Using the Search & Skip Functions . . . . . . . .12
Using the Display Function . . . . . . . . . . . . . . .12
Using the Disc and Title Menu . . . . . . . . . . . .13
Using the Function Menu . . . . . . . . . . . . . . . .14
Repeat Play . . . . . . . . . . . . . . . . . . . . . . . . . .14
Program Play & Random Play . . . . . . . . . . . .15
Slow Repeat play . . . . . . . . . . . . . . . . . . . . . .15
LOADING
PLAY
Video/Audio Cable
Install Batteries in the Remote
Advanced Functions
1. Open the battery cover on the back of the
remote.
2. Insert two AAA batteries. Make sure that the
polarities (+ and -) are aligned correctly.
3. Replace the battery cover.
Adjusting the Aspect Ratio (EZ View) . . . . . . .16
Selecting the Audio Language . . . . . . . . . . . .17
Selecting the Subtitle Language . . . . . . . . . . .17
Changing the Camera Angle . . . . . . . . . . . . .18
Using the Instant Replay/Skip Function . . . . .18
Using the Bookmark Function . . . . . . . . . . . .19
Using the Zoom Function . . . . . . . . . . . . . . . .20
Clips Menu for MP3/JPEG . . . . . . . . . . . . . . .20
Folder Selection . . . . . . . . . . . . . . . . . . . . . . .21
MP3 Play . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Picture CD Playback . . . . . . . . . . . . . . . . . . .22
LOADING
If remote doesn’t operate properly:
4
• Check the polarity + - of the batteries (Dry-Cell)
• Check if the batteries are drained.
• Check if remote sensor is blocked by obstacles.
• Check if there is any fluorescent lighting nearby.
Changing Setup menu
Using the Setup Menu . . . . . . . . . . . . . . . . . .23
Setting Up the Language Features . . . . . . . . .24
Setting Up the Audio Options . . . . . . . . . . . . .26
Setting Up the Display Options . . . . . . . . . . . .27
Setting Up the Parental Control . . . . . . . . . . .28
5
5. Environmental info
* The battery used in this product contains chemicals
that are harmful to the environment.
* So, dispose of batteries in the proper manner,
according to federal, state, and local regulations.
Reference
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . .30
Specifications . . . . . . . . . . . . . . . . . . . . . . . .31
ENG-2
ENG-3
General Features
Disc Type and Characteristics
Excellent Sound
Note
Dolby Digital, a technology developed by Dolby
Laboratories provides crystal clear sound
reproduction.
* Discs which cannot be played with this player.
• DVD-ROM
• DVD-RAM
• CD-ROM
• CDV
• CDI
• HD layer of super Audio CD
• CDGs play audio only, not graphics.
Screen
Video with MPEG-2 compression technology.
Both regular and widescreen(16:9) pictures can be
viewed.
Slow Motion
An important scene can be viewed in slow motion.
Programmed Play
You can program tracks to play in desired order.
(CD)
This DVD player is capable of playing the following types of discs with the corresponding
logos:
Disc Types (Logos)
Recording Types Disc Size
DVD
Audio
+
Video
* Ability to play back may depend on recording
conditions.
• DVD-R, +R
• CD-RW
• DVD+RW, -RW
* The unit may not play certain CD-R, CD-RW and
DVD-R due to the disc type or recording
conditions.
AUDIO-CD
Various On-Screen Menu Functions
You can select various languages (Audio/Subtitle)
and screen angles while enjoying movies.
EZ VIEW
Easy View can convert Letter Box images to
full screen viewing on your conventional TV.
Digital Photo Viewer (JPEG)
You can view the Digital Photos on your TV.
Repeat
You can repeat a song or movie simply by pressing
the REPEAT button.
8 Cm
Characteristics
Single-sided 240 min. • DVD contains excellent sound and
Double-sided 480 min. video due to Dolby Digital and
MPEG-2 system.
•
Various screen and audio functions
Single-sided 80 min.
can be easily selected through the
Double-sided 160 min.
on-screen menu.
12 Cm
74 min.
8 Cm
20 min.
Audio
Parental Control
The parental control allows users to set the level
necessary to prohibit children from viewing harmful
movies such as those with violence, adult subject
matter, etc.
12 Cm
Max. Playing Time
• CD is recorded as a Digital
Signal with better audio quality,
less distortion and less
deterioration of audio quality
over time.
COPY PROTECTION
Many DVD discs are encoded with copy
protection. Because of this, you should only
connect your DVD player directly to your TV, not
to a VCR. Connecting to a VCR results in a
distorted picture from copy-protected DVD discs.
This product incorporates copyright protection
technology that is protected by methods claims of
certain U.S. patents and other intellectual property
rights owned by Macrovision Corporation and other
rights owners. Use of this copyright protection
technology must be authorized by Macrovision
Corporation, and is intended for home and other
limited viewing uses only unless otherwise
authorized by Macrovision Corporation.
Reverse engineering or disassembly is prohibited.
PROGRESSIVE SCAN OUTPUTS (525p/625p)
MP3
Disc Markings
~
PAL
Play Region Number
Play Region Number
Both the DVD player and the discs are coded by region.
These regional codes must match in order for the disc to
play. If the codes do not match, the disc will not play.
PAL broadcast system in U.K, France,
Germany, etc.
The Region Number for this player is described on the
rear panel of the player.
Dolby Digital disc
STEREO
DIGITAL
SOUND
Stereo disc
Digital Audio disc
DTS disc
MP3 disc
“CONSUMERS SHOULD NOTE THAT NOT ALL
HIGH DEFINITION TELEVISION SETS ARE FULLY
COMPATIBLE WITH THIS PRODUCT AND MAY
CAUSE ARTIFACTS TO BE DISPLAYED IN THE
PICTURE, IN CASE OF 525 OR 625 PROGRESSIVE
SCAN PICTURE PROBLEMS, IT IS RECOMMENDED THAT THE USER SWITCH THE CONNECTION
TO THE ‘STANDARD DEFINITION’ OUTPUT.
IF THERE ARE QUESTIONS REGARDING OUR TV
SET COMPATIBILITY WITH THIS MODEL 525p AND
625p DVD PLAYER, PLEASE CONTACT OUR
CUSTOMER SERVICE CENTER.”
This unit can play discs created from MP3 files.
Instant Replay
This function is used to replay the previous
10 seconds of the movie from the current
position.
Instant Skip
This function skips playback ahead 10
seconds.
ENG-4
ENG-5
Description-Front Panel
Description-Rear Panel
9
Pr
Pb
Y
STANDBY/ON
EZ VIEW
COAXIAL
COMPONENT VIDEO OUT
R
ANALOG AUDIO OUT
1
2
3
4
5 6
7
L
VIDEO OUT
S-VIDEO OUT
8
Front Panel Controls
6. EZ VIEW
• Easy View can convert Letter Box images to full
screen viewing on your conventional TV.
1. STANDBY/ON (
)
• When the unit is first plugged in, the indicator
lights. When STANDBY/ON is pressed on again,
the light goes out and the player is turned on.
2. DISC TRAY
• Place the disc here.
3. DISPLAY
• Operation indicators are displayed here.
5. STOP (
)
• Stops disc play.
2
3
7. PLAY/PAUSE (
)
• Begin or pause disc play.
Rear Panel
8. SKIP (
) / SEARCH
• Allows you to search forward through a disc.
Use to skip the title, chapter or track.
1. DIGITAL AUDIO OUT JACKS
• Use either a coaxial digital cable to connect to a
compatible Dolby Digital receiver.
Use to connect to an A/V Amplifier that contains
a Dolby Digital, MPEG-2 or DTS decoder.
9. SKIP (
) / SEARCH
• Allows you to search backward through a disc.
Use to skip the title, chapter or track.
4. OPEN/CLOSE (
)
• Press to open and close the disc tray.
1
4
3. VIDEO OUT JACK
• Use a video cable to connect to the Video input
jack on your television.
• The Video Output in Setup Menu must be set to
the Component (I-SCAN) or S-Video.
1
2
3
6
5. COMPONENT VIDEO OUT JACKS
• Use these jacks if you have a TV with
Component Video in jacks. These jacks provide
Pr, Pb and Y video. Along with S-Video,
Component Video provides the best picture
quality.
• If Component (P-SCAN) Video Output is
selected in Setup Menu, progressive scan mode
will work.
• If Component (I-SCAN) Video Output is selected
in Setup Menu, interlaced scan mode will work.
2. ANALOG AUDIO OUT JACKS
• Connect to the Audio input jacks of your
television, audio/video receiver.
Display Indicators
5
6. SCART JACK
• Connect to a TV scart input jack.
Important Note
4. S-VIDEO OUT JACK
• Use the S-Video cable to connect this jack to
the S-Video jack on your television for a higher
picture quality.
• The Video Output in Setup Menu must be set to
the S-Video.
• Consult your TV User’s Manual to find out if your
TV supports Progressive Scan.
If Progressive Scan is supported, follow the TV
User’s Manual’s instructions regarding Progressive
Scan settings in the TV’s menu system.
Front Panel Display
• If Component (P-SCAN) Video Output is selected
in Setup Menu, Video and S-Video will not work.
1. Disc type indicators
2. Play / Pause / Forward play
3. Displays various messages concerning operations such as PLAY, STOP, LOAD ...
no DISC : No disc loaded.
OPEN : The disc tray is open.
LOAD : Player is loading disc information.
• See page 28 to get more information on how to
use the Setup Menu.
ENG-6
ENG-7
Tour of the Remote Control
Choosing a Connection
6. STOP Button (
)
The following shows examples of connections commonly used to connect the DVD player with a TV
and other components.
7. MENU Button
1
• Brings up the DVD player’s setup menu.
11
8. RETURN Button
2
Before Connecting the DVD Player
• Always turn off the DVD player, TV, and other components before you connect or disconnect any cables.
• Returns to a previous menu.
• Refer to the owner’s manual of the additional components you are connecting for more information on those
particular components.
9. REPEAT A-B Button
• Use to mark a segment to repeat between A and B.
12
13
14
3
4
Connection to an Audio
10. SUBTITLE Button
11. OPEN/CLOSE (
5
Method 1
) Button
Method 2
• To open and close the disc tray.
6
7
15
16
8
17
18
12. CLEAR Button
• Use to remove menus or status displays from the
screen.
AUDIO
SYSTEM
13. INSTANT REPLAY Button
• This function is used to replay the previous 10
seconds of the movie from the current position.
9
19
20
21
22
10
2ch Amplifier
Dolby Digital Decoder
Audio Input Jacks
Digital Audio Input Jack
14. INSTANT SKIP Button
• This function skips playback ahead 10 seconds.
15. PLAY/PAUSE Button (
)
• Begin/Pause disc play.
16. INFO Button
• Displays the current disc mode.
17. DISC MENU Button
• Brings up the Disc menu.
18. ENTER/DIRECTION Button
(UP/DOWN or LEFT/RIGHT Buttons)
DVD Function Buttons
• This button functions as a toggle switch.
1. DVD POWER Button
19. EZ VIEW Button
• Turns the power on or off.
• Easy View can convert Letter Box images to full
screen viewing on your conventional TV.
2. NUMBER Buttons
R
L
COAXIAL
ANALOG AUDIO OUT
Analog Audio Out
Digital Audio Out
20. REPEAT Button
3. PROG Button
• Allows you to repeat play a title, chapter, track, or
disc.
• Allows you to program a specific order.
4. STEP Button
21. ANGLE Button
• Advances play one frame at a time.
5. SEARCH/SKIP Buttons (
DVD
Player
/
• Use to access various camera angles on a DVD.
,
/
)
• Allows you to search forward/backward through
a disc. Use to skip the title, chapter or track.
22. AUDIO Button
• Use this button to access various audio functions
on a disc.
ENG-8
ENG-9
Choosing a Connection
Playing a Disc
7. Step Motion Play (DVD only)
Connection to a TV (For Video)
Before Play
TV (Normal, Widescreen, Projection, etc..)
• Turn on your TV and press the TV/VIDEO button
to select the video mode.
• Turn on your Audio System and select AUX, CD or
DVD.
Basic Audio
Method 1
Method 2
Method 3
Method 4
Method 5
Good
picture
Better
picture
Best
picture
Best
picture
Optimum
picture
After plugging in the player, the first time you press
the DVD POWER button, this screen comes up :
If you want to select the language, press a
NUMBER button. (This screen will only appear
when you plug in the player for the first time.)
TV
AV
Cable
S-Video
Cable
Scart
Cables
(not
supplied)
OR
Press the STEP button on the remote during play.
- Each time the button is pressed, a new frame will
appear.
- No sound is heard during STEP mode.
- Press the PLAY/PAUSE (
) to resume normal play.
(You can only perform step motion play in the forward
direction.)
8. Slow Motion Play (DVD only)
Press and hold the
button on the remote during
PAUSE or STEP mode. Press again and you can select
slow motion play for 1/8, 1/4 and 1/2 of normal speed.
- No sound is heard during slow mode.
- Press the PLAY/PAUSE (
) to resume normal play.
- Reverse slow motion play will not work.
Video
Cables
OR
OR
RESUME function
DVD
Player
Pr
R
ANALOG AUDIO OUT
Pb
Y
Pr
Pb
When you stop disc play, the player remembers
where you stopped, so when you press the
PLAY (
) again, it will pick up where you left off.
(unless the disc is removed or the player is
unplugged, or if you press the STOP (
) button
twice.)
Y
L
VIDEO OUT
S-VIDEO OUT
Audio Output Video Output S-Video
Jack
Jack
Jacks
COMPONENT VIDEO OUT
SCART Jack
Component Video
Jacks
(Interlace)
COMPONENT VIDEO OUT
Component Video
Jacks
(Progressive)
Method 1
DVD Player + TV with Video Input Jack
(The Video Output in Setup Menu must be set to the S-Video or SCART Output.)
Method 2
DVD Player + TV with S-Video Input Jack
(The Video Output in Setup Menu must be set to the S-Video.)
Method 3
DVD Player + TV with Scart Input Jacks (Audio & Video)
(The Video Output in Setup Menu must be set to SCART Output.)
Method 4
DVD Player + TV with interlace Scan Component Video Jacks
(The Video Output in Setup Menu must be set to the Component (I-SCAN).)
Method 5
DVD Player + TV with Progressive Scan Component Video Jacks.
(The Video Output in Setup Menu must be set to the Component (P-SCAN).)
• If you want to convert Video Output to the Progressive Scan, you have to first connect Video or S-Video on
your TV. Then select Component (P-SCAN) out of Video Output in Setup Menu. Within 10 seconds, change the
TV’s external input to 625p/525p(576p/480p or Component) and select “Yes” (See Page 28).
• If Component (P-SCAN) Video Output is selected in Setup Menu, Video and S-Video will not work.
Play
1. Press the OPEN/CLOSE button.
The STANDBY indicator light goes out and the tray
opens.
2. Place a disc gently into the tray with the disc’s
label facing up.
3. Press the PLAY/PAUSE (
) button or
OPEN/CLOSE button to close the disc tray.
4. Stopping Play
Press the STOP (
) button during play.
5. Removing Disc
Note
• If the player is left for 5 minutes in pause mode, it
will stop.
• If the player is left in the stop mode for more than
30 minutes, the power will automatically shut off.
(Automatic Power-Off Function)
• If the player is left in the stop mode for more than
one minute without any user interaction, a screen
saver will be activated. Press the PLAY (
)
button to resume normal play.
• This
icon indicates an invalid button press.
Press the OPEN/CLOSE button.
6. Pausing Play
Press the PLAY/PAUSE (
) or STEP button on the
remote during play.
- Screen stops, no sound.
- To resume, press the PLAY/PAUSE (
) button once
again.
Important Note
• Consult your TV User’s Manual to find out if your TV supports Progressive Scan.
If Progressive Scan is supported, follow the TV User’s Manual’s instructions regarding Progressive Scan
settings in the TV’s menu system.
• Depending on your TV, the Method of connection may differ from the illustration above.
ENG-10
ENG-11
Using the Search & Skip Functions
Using the Display Function
During play, you can search quickly through a
chapter or track or use the skip function to
jump to the next selection.
When Playing a DVD/CD
Searching through a Chapter or Track
2. Use the UP/DOWN buttons to select the desired
item.
Press the
or
button on the remote for more
than 1 second and press again to search at a faster
speed on a DVD or CD.
DVD 2X, 8X, 32X, 128X
CD
2X, 4X, 8X
1. During play, press the INFO button on the
remote.
3. Use the LEFT/RIGHT buttons to make the
desired setup and then press ENTER.
• You may use the number buttons of the remote
control to directly access a title, chapter or to
start the playback from the desired time.
4. To make the screen disappear, press the INFO
button again.
To access the desired title when there is
Title more than one in the disc.
For example, if there is more than one
movie on a DVD, each movie will be
identified.
Using the Disc and Title Menu
Using the Disc Menu
1. During the playback of a DVD disc, press the
MENU button on the remote.
2. Select Disc Menu using the UP/DOWN buttons,
then press the RIGHT or ENTER button.
Most DVD discs are recorded in
Chapter chapters so that you can quickly find a
specific passage (similar to tracks on an
audio CD).
Allows playback of the film from a
Time desired time. You must enter the starting
time as a reference.
Refers to the language of the film
DVD
Audio soundtrack. In the example, the
Skipping Tracks
During play, press the
Using the Display Function
DVD
or
button.
Title
01
Chapter 02
• When playing a DVD, if you press the
button, it
moves to the next chapter. If you press the
button, it
moves to the beginning of the chapter. One more press
makes it move to the beginning of the previous chapter.
Time
Audio
Subtitle
0:00:13
Using the Title Menu
Refers to the subtitle languages
2. Select Title Menu using the UP/DOWN buttons,
then press the RIGHT or ENTER button.
1. During the playback of a DVD disc, press the
MENU button on the remote.
ENG 5.1CH
Off
ENTER
• When playing a CD, if you press the
button, it moves
to the next track. If you press the
button, it moves to
the beginning of the track. One more press makes it move
to the beginning of the previous track.
soundtrack is played in English 5.1CH.
A DVD disc can have up to eight
different soundtracks.
Subtitle available in the disc.
You will be able to choose the subtitle
languages or, if you prefer, turn them off
from the screen.
A DVD disc can have up to 32 different
subtitles.
CD
CD
Track 01
Time 0:00:48
ENTER
Note
• Depending on the disc, the Title and Disc Menus
may not work.
• Title Menu will only be displayed if there are at
least two titles in the disc.
• You can also use the Disc Menu, using the DISC
MENU button on the remote.
ENG-12
ENG-13
Using the Function Menu
Using the Function Menu
1. Press the MENU button during playback.
2. Use the UP/DOWN buttons to highlight Function,
then press the RIGHT or ENTER button.
3. Function selection screen appears: Info, Zoom,
Bookmark, Repeat and EZ View.
-
Info (See Page 12~13)
Zoom (See Page 20)
Bookmark (See Page 19)
Repeat (See Page 14)
EZ View (See Page 16)
Repeat Play
Program Play & Random Play
Repeat the current track, chapter, title, a
chosen section (A-B), or all of the disc.
Program Play (CD)
When playing a DVD/CD
2. Use the LEFT/RIGHT buttons to select
PROGRAM. Press the ENTER button.
1. Press the REPEAT button on the remote.
Repeat screen appears.
2. Select Chapter, Title or A-B using the
LEFT/RIGHT buttons.
• Chapter ( ) : repeats the chapter that is playing.
• Title ( T ) : repeats the title that is playing.
• A-B : repeats a segment of the disc that you select.
1. Press the PROG button.
3. Use the LEFT/RIGHT/UP/DOWN buttons to
select the first track to add to the program.
Press the ENTER button. The selection numbers
appear in the Program Order box.
4. Press the PLAY/PAUSE (
) button.
The disc will be played in programmed order.
DVD
4. Use the UP/DOWN button to highlight one of the
5 functions. Then press the RIGHT or ENTER
button to access the function.
PROGRAM
Off
01
T
01 A - B
REPEAT
RANDOM
Slow Repeat Play
ENTER
This feature allows you slowly to repeat
scenes containing sports, dancing, musical
instruments being played etc. so you can
study them more closely.
CD
Off
T
01
D
01 A - B
REPEAT
ENTER
PROGRAM 01
Program Order
Track
3. Press ENTER.
Note
• You can also directly select the parts of these
functions using their respective buttons on the
remote.
Note
• Depending on the disc, the Program and Random
Play functions may not work.
• PROGRAM/RANDOM playback cannot be used if
the disc contains more than two types of file
extensions.
• This unit can support a maximum of 20
programmed tracks.
• While in playback mode, press the CLEAR button
on the remote control to cancel Programmed Play
or Random Play.
01
05
09
13
02
06
10
14
4. To return to normal play, press REPEAT again,
then press the LEFT/RIGHT buttons to select Off
and press ENTER.
* REPEAT A-B button
• Press the REPEAT A-B button to select the point where
the function starts. (A)
The B is automatically highlighted.
• Press the REPEAT A-B button to select the point where
the function ends. (B)
• To terminate the function, press the 'CLEAR' button or
the 'REPEAT A-B' button again.
• A-B REPEAT does not allow you to set point (B) until at
least 5 seconds has elapsed after point (A) has been
set.
Note
• DVD repeats play by chapter or title, CD repeats
play by disc or track.
• Depending on the disc, the Repeat function may
not work.
ENG-14
03
07
11
15
04
08
12
16
ENTER
------
------
------
RETURN
------
CLEAR
When playing a DVD
1. During play, press the PLAY/PAUSE (
button.
)
2. Press and hold the
button on the remote
during PAUSE or STEP mode. Press again and
you can select slow motion play for 1/8, 1/4 and
1/2 of normal speed.
3. Press the REPEAT A-B button to select the point
where the function starts. (A)
Random Play (CD)
1. Press the PROG button.
4. Press the REPEAT A-B button to select the point
where the function ends. (B)
2. Use the LEFT/RIGHT buttons to select RANDOM.
Press the ENTER button.
PROGRAM
RANDOM
Note
• The disc will play from A to B repeatedly at the
speed you chose.
• To terminate the function, press the 'CLEAR'
button or the 'REPEAT A-B' button again.
• A-B REPEAT does not allow you to set point (B)
until at least 5 seconds has elapsed after point (A)
has been set.
ENG-15
Adjusting the Aspect Ratio (EZ View)
Selecting the Audio Language
To play back using aspect ratio (DVD)
If you are using a 4:3 TV
Press the EZ VIEW button.
• The screen size changes when the button is
pressed repeatedly.
• The screen zoom mode operates differently
depending on the screen setting in the initial setup
menu.
• To ensure correct operation of the EZ VIEW
button, you should set the correct aspect ratio in
the initial setup (See page 27).
1. For 16:9 aspect ratio discs
• 4:3 Letter Box
Displays the content of the DVD title in 16:9
aspect ratio. The black bars will appear at the
top and bottom of the screen.
• 4:3 Pan Scan
The left and right of the screen are cut off and
displays the central portion of the 16:9 screen.
• Screen Fit
The top and bottom of the screen are cut off
and the full screen appears.
The picture will look vertically stretched.
If you are using a 16:9 TV
1. For 16:9 aspect ratio discs
• Wide Screen
• Screen Fit
The top and bottom of the screen are cut off.
When playing a 2.35:1 aspect ratio disc, the
black bars at the top and bottom of the screen
will disappear. The picture will look vertically
stretched. (Depending on the type of disc, the
black bars may not disappear completely.)
You can select a desired subtitle quickly and
easily with the SUBTITLE button.
Using the AUDIO button
Using the SUBTITLE button
1. Press the AUDIO button.
1. Press the SUBTITLE button.
2. The Audio changes when the button is pressed
repeatedly.
2. The subtitle changes when the button is pressed
repeatedly.
- The audio languages are represented by abbreviations.
3. Press the AUDIO button to select Stereo, Left or
Right. (On CD)
3. To turn off the display, press the CLEAR or
RETURN button.
- Initially, the subtitle will not appear on screen.
- The subtitle languages are represented by
abbreviations.
DVD
ENG DOLBY DIGITAL 5.1CH
AUDIO
ENG
SUBTITLE
Off
SUBTITLE
2. For 4:3 aspect ratio discs
• Normal Screen
Displays the content of the DVD title in 4:3
aspect ratio.
• Screen Fit
The top and bottom of the screen are cut off
and the full screen appears.
The picture would look vertically stretched.
• Zoom Fit
The top, bottom, left and right of the screen are
cut off and the central portion of the screen is
enlarged.
CD
Stereo
AUDIO
• Zoom Fit
The top, bottom, left and right of the screen are
cut off and the central portion of the screen is
enlarged.
2. For 4:3 aspect ratio discs
• Normal Wide
Displays the content of the DVD title in 16:9
aspect ratio. The picture will look horizontally
stretched.
• Screen Fit
The top and bottom of the screen are cut off
and the full screen appears.
The picture will look vertically stretched.
You can select a desired language quickly and
easily with the AUDIO button.
• Zoom Fit
The top, bottom, left and right of the screen are
cut off and the central portion of the screen is
enlarged.
Displays the content of the DVD title in 16:9
aspect ratio.
Selecting the Subtitle Language
Note
• This function may behave differently depending on
the type of disc.
• Zoom Fit
The top, bottom, left and right of the screen are
cut off and the central portion of the screen is
enlarged.
• Vertical Fit
When a 4:3 DVD is viewed on a 16:9 TV, black
bars will appear at the left and right of the
screen in order to prevent the picture from
looking horizontally stretched.
ENG-16
Note
• This function depends on what languages are
encoded on the disc and may not work with all
DVDs.
• A DVD disc can contain up to 8 audio languages.
• How to have the same audio language come up
whenever you play a DVD;
Refer to “Setting Up the Language Features” on
page 25.
Note
• This function depends on what languages are
encoded on the disc and may not work with all
DVDs.
• A DVD disc can contain up to 32 subtitle
languages.
• How to have the same subtitle language come
up whenever you play a DVD;
Refer to “Setting Up the Language Features” on
page 25.
ENG-17
Changing the Camera Angle
Using the Instant Replay/Skip Function
When a DVD contains multiple angles of a
particular scene, you can select the Angle
function.
Using the Instant Replay function (DVD)
Using the ANGLE button
If you press the INSTANT REPLAY button, the
current scene moves backward about 10 seconds,
and plays back.
Press the ANGLE button to see if an ANGLE
(
) mark is present at the upper left hand
corner of the screen.
If you miss a scene, you can see it again using
this function.
* Depending on the disc, the Instant Replay function may
not work.
Using the Bookmark Function
This feature lets you bookmark sections of a
DVD so you can quickly find them at a later
time.
Using the Bookmark Function (DVD)
1. During play, press the MENU button on the
remote.
2. Use the UP/DOWN buttons to highlight Function,
then press the RIGHT or ENTER button.
1. When an ANGLE mark is shown, press the
ANGLE button, then an ANGLE select icon will
appear at the upper hand corner of the screen.
3. Select Bookmark using the UP/DOWN buttons,
then press the RIGHT or ENTER button.
2. Press the ANGLE button to select the desired
screen angle.
4. Use the LEFT/RIGHT buttons to move to the
desired bookmark icon.
3. To turn off the display, press the CLEAR or
RETURN button.
5. When you reach the scene you want to mark,
press the ENTER button. The icon will change to
a number (1, 2, or 3).
4/6
Recalling a Marked Scene
1. During play, press the MENU button on the
remote and select the Bookmark.
2. Use the LEFT/RIGHT buttons to select a marked
scene.
3. Press the PLAY/PAUSE (
the marked scene.
) buttons to skip to
ANGLE
Clearing a Bookmark
Using the Instant Skip function (DVD)
Use this function to skip playback about 10
seconds ahead of the current scene.
Press the INSTANT SKIP button.
- Playback will skip ahead 10 seconds.
- Depending on the disc, this function may not work.
Note
• If the disc has only one angle, this feature won’t
work. Currently, very few discs have this feature.
1. During play, press the MENU button on the
remote and select the Bookmark.
2. Use the LEFT/RIGHT buttons to select the
bookmark number you want to delete.
3. Press the CLEAR button to delete a bookmark
number.
Note
• Up to three scenes may be marked at a time.
• Depending on the disc, the Bookmark function may
not work.
ENG-18
ENG-19
Using the Zoom Function
Clips Menu for MP3/JPEG
Using the Zoom Function (DVD)
1. Open the disc tray.
1. During play or pause mode, press the MENU
button on the remote.
2. Place the disc on the tray.
- Place the disc with the labeled side up.
2. Use the UP/DOWN buttons to highlight Function,
then press the RIGHT or ENTER button.
3. Close the tray.
- The tray closes and you should get a screen
that looks like the one below.
3. Select Zoom using the UP/DOWN buttons, then
press the RIGHT or ENTER button.
4. Use the UP/DOWN or LEFT/RIGHT buttons to
select the part of the screen you want to zoom in
on.
Off
00:00:23
5. Press the ENTER button.
1_mp3
B e c a u s e Yo u
- During DVD play, press ENTER to zoom in
2X/4X/2X/Normal in order.
Sad Day
Folder Selection
MP3 Play
The folder can only be selected in the Stop
mode.
• To select the Parent Folder
Press the RETURN button to go to parent folder,
or use the UP/DOWN buttons to select “..” and
press ENTER to go to the parent folder.
• To select the Peer Folder
Use the LEFT/RIGHT buttons to highlight left
window. Use the UP/DOWN buttons to select the
desired folder, then press ENTER.
• To select the Sub-Folder
Use the LEFT/RIGHT buttons to highlight right
window. Use the UP/DOWN buttons to select the
desired folder, then press ENTER.
1. Open the disc tray.
2. Place the disc on the tray.
- Place the disc with the labeled side up.
3. Close the tray.
- The tray closes and you should get a screen
that looks like the one below.
MP3 Play Function
1. Select the desired folder.
2. Use the UP/DOWN or LEFT/RIGHT buttons to
select a song file.
3. Press ENTER to begin playback of the song file.
Off
00:00:23
1_mp3
Root
Parent Folder, Current Folder
and Peer Folders
Folders and Files in
Current Folder
JPEG
B e c a u s e Yo u
Sad Day
Parent Folder
MP3
•
: Name of currently playing file.
•
: Current Playback Time.
MUSIC
Current Folder
1st
Sub-Folders
2nd
•
: Current Playback Mode : There are 4
modes, toggle by the REPEAT button.
- Off : Normal Playback
- Track : Repeats the current track.
- Folder : Repeats the current folder.
- Random : Files in the disc will be played
in random order.
•
: MP3 file icon.
•
: JPEG file icon.
•
: Folder icon.
•
: Current Folder icon.
ENG-20
Repeat/Random playback
SONG FILE 1
Peer Folders
SONG FILE 2
SONG FILE 3
Press the REPEAT button to change playback
mode. There are 4 modes, Off, Track, Folder and
Random.
- Off : Normal Playback
- Track : Repeats the current song file.
- Folder : Repeats the song files which have the
same extension in the current folder.
- Random : Song files which have the same
extension will be played in random
order.
* To resume normal play, press the CLEAR button.
ENG-21
MP3 Play
CD-R MP3 discs
When you record MP3 files on the CD-R, please
refer to the following.
• Your MP3 files should be ISO 9660 or JOLIET format.
ISO 9660 format and Joliet MP3 files are compatible with
Microsoft's DOS and Windows, and with Apple's Mac.
This format is the most widely used.
• When naming your MP3 files, do not exceed 8
characters, and enter ".mp3," as the file extension.
General name format of: Title.mp3. When composing your
title, make sure that you use 8 characters or less, have no
spaces in the name, and avoid the use of special
characters including: (.,/,\,=,+).
• Use a decompression transfer rate of at least 128
Kbps when recording MP3 files.
Sound quality with MP3 files basically depends on the rate
of compression/decompression you choose. Getting CD
audio sound requires an analog/digital sampling rate, that
is conversion to MP3 format, of at least 128 Kbps and up
to 160 Kbps. However, choosing higher rates, like 192
Kbps or more, only rarely give better sound quality.
Conversely, files with decompression rates below 128
Kbps will not be played properly.
• Do not try recording copyright protected MP3 files.
Certain "secured" files are encrypted and code protected
to prevent illegal copying. These files are of the following
types: Windows MediaTM (registered trade mark of
Microsoft Inc) and SDMITM (registered trade mark of The
SDMI Foundation). You cannot copy such files.
• Important: The above recommendations cannot be taken
as a guarantee that the DVD player will play MP3
recordings, or as an assurance of sound quality. You
should note that certain technologies and methods for
MP3 file recording on CD-Rs prevent optimal playback of
these files on your DVD player (degraded sound quality
and in some cases, inability of the player to read the files).
Picture CD Playback
Picture CD Playback
1. Select the desired folder. (See page 21 to select
the folder)
2. Use the UP/DOWN buttons to select a Picture file in
clips menu and then press the ENTER button. You
should get a screen that looks like the one below.
ENTER RETURN
Note
• If no buttons on the remote control are pressed for
10 seconds, the menu will disappear.
Press the INFO button on the remote control to
display the menu again.
• Press the STOP button to return to the clips menu.
• When playing a Kodak Picture CD, the unit
displays the Photo directly, not the clips menu.
CD-R JPEG Discs
• Use the INFO button on the remote control to select
the menu you want to view and then press the
ENTER button.
•
: Returns to the Album Screen.
• To see the next 6 pictures, press the
• To see the previous 6 pictures, press the
button.
button.
•
: Each time the ENTER button is pressed, the
picture rotates 90 degrees clockwise.
•
: Each time the ENTER button is pressed, the
picture is enlarged up to 4X.
(Normal ➝ 2X ➝ 4X ➝ 2X ➝ Normal)
•
: The unit enters slide show mode.
*Before the Slide Show begin, the picture interval must
be set.
Using the Setup Menu
The Setup menu lets you customize your DVD
player by allowing you to select various
language preferences, set up a parental level,
even adjust the player to the type of television
screen you have.
1. With the unit in Stop mode, press the MENU
button on the remote. Select Setup using
UP/DOWN buttons, then press the RIGHT or
ENTER button.
• Only files with the ".jpg" and ".JPG" extensions can be
played.
Language Setup : Setup of the Language.
• If the disc is not closed, it will take longer to start playing
and not all of the recorded files may be played.
Audio Setup : Setup of the Audio Options.
Display Setup : Setup of the Display Options.
Use to select which type of screen you want to
watch and several display options.
• Only CD-R discs with JPEG files in ISO 9660 or Joliet
format can be played.
• The name of the JPEG file may not be longer than 8
characters and should contain no blank spaces or special
characters (. / = +).
Parental Setup : Setup of the Parental Level.
Allows users to set the level necessary to
prevent children from viewing unsuitable
movies such as those with violence, adult
subject matter, etc.
• Only a consecutively written multisession disc can be
played. If there is a blank segment in the multisession
disc, the disc can be played only up to the blank
segment.
• A maximum of 500 images can be stored on a single CD.
• Kodak Picture CDs are recommended.
Disc Menu
• When playing a Kodak Picture CD, only the JPEG files in
the pictures folder can be played.
Title Menu
Function
• Kodak Picture CD : The JPEG files in the pictures folder
can be played automatically.
Setup
• Konica Picture CD : If you want to see the Picture, select
the JPEG files in the clips menu.
TIMER:
ENTER RETURN
• Fuji Picture CD : If you want to see the Picture, select the
JPEG files in the clips menu.
• QSS Picture CD : The unit cannot play QSS Picture CDs.
• If a number of files in 1 Disc are over 3000, only 3000
JPEG file can be played.
• This unit can play a maximum of 3000 files and 300
folders per disc.
•
: When this icon is selected and ENTER is
pressed, the pictures change automatically in
intervals of about a 6 second.
•
: The pictures change automatically in intervals
of about a 12 second.
•
: The pictures change automatically in intervals
of about a 18 second.
• If a number of folders in 1 Disc are over 300, only JPEG
files in 300 folders can be played.
2. Use the UP/DOWN buttons on the remote to
access the different features.
3. Press the ENTER or RIGHT button to access the
sub features.
To make the setup screen disappear after setting
up, press the MENU button again.
Note
Depending on the disc, some Setup Menu
selections may not work.
*Depending on the file size, each interval between images
may be longer or shorter.
ENG-22
ENG-23
Setting Up the Language Features
If you set the player menu, disc menu, audio
and subtitle language in advance, they will
come up automatically every time you watch a
movie.
Setting Up the Language Features
Using the Disc Menu Language
Using the Audio Language
Using the Subtitle Language
This function changes the text language only on the
disc menu screens.
1. With the unit in Stop mode, press the MENU
button.
1. With the unit in Stop mode, press the MENU
button.
Using the Player Menu Language
1. With the unit in Stop mode, press the MENU
button.
2. Select Setup using UP/DOWN buttons, then
RIGHT or ENTER button.
2. Select Setup using UP/DOWN buttons, then
RIGHT or ENTER button.
1. With the unit in Stop mode, press the MENU
button.
2. Select Setup using UP/DOWN buttons, then
RIGHT or ENTER button.
3. Select Language Setup using UP/DOWN
buttons, then press the RIGHT or ENTER button.
3. Select Language Setup using UP/DOWN
buttons, then press the RIGHT or ENTER button.
2. Select Setup using UP/DOWN buttons, then
RIGHT or ENTER button.
3. Select Language Setup using UP/DOWN
buttons, then press the RIGHT or ENTER button.
4. Select Audio using UP/DOWN buttons, then
press the RIGHT or ENTER button.
4. Select Subtitle using UP/DOWN buttons, then
press the RIGHT or ENTER button.
3. Select Language Setup using UP/DOWN
buttons, then press the RIGHT or ENTER button.
4. Select Disc Menu using UP/DOWN buttons, then
press the RIGHT or ENTER button.
5. Press the UP/DOWN buttons to select ‘English’.
5. Use the UP/DOWN buttons to select ‘English’.
e.g) Setting up in English.
5. Use the UP/DOWN buttons to select ‘English’.
- Select “Others” if the language you want is not listed.
- Select “Original” if you want the default soundtrack
language to be the original language the disc is
recorded in.
- Select “Automatic” if you want the subtitle language to
be the same as the language selected as the audio
preference.
- Select “Others” if the language you want is not listed.
- Select “Others” if the language you want is not listed.
Some discs may not contain the language you select
as your initial language; in that case the disc will use its
original language setting.
e.g) Setting up in English.
AUDIO LANGUAGE
DISC MENU LANGUAGE
Audio
Disc Menu
SUBTITLE LANGUAGE
4. Select Player Menu using UP/DOWN buttons,
then press the RIGHT or ENTER button.
IIII
IIII
IIII
IIII
Original
Others
Automatic
Subtitle
Others
LANGUAGE SETUP
IIII
Others
6. Press the ENTER button.
6. Press the ENTER button.
- English is selected and the screen returns to SETUP
menu.
- English is selected and the screen returns to SETUP
menu.
6. Press the ENTER button.
- English is selected and the screen returns to SETUP
menu.
5. Use the UP/DOWN buttons to select ‘English’.
Note
• If the selected language is not recorded on the
disc, the original pre-recorded language is
selected.
• How to make the SETUP menu disappear or
return to menu screen during set up;
Press RETURN or LEFT button.
6. Press the ENTER button.
- English is selected and the screen returns to SETUP
menu.
- To make the SETUP menu disappear, press the
RETURN or LEFT button.
ENG-24
ENG-25
Setting Up the Audio Options
Setting Up the Display Options
1. With the unit in Stop mode, press the MENU button.
2. Select Setup using UP/DOWN buttons, then
RIGHT or ENTER button.
3. Select Audio Setup using UP/DOWN buttons,
then press the RIGHT or ENTER button.
DTS
1. Off : Doesn’t output digital signal.
2. On : Outputs DTS Bitstream via digital output only.
Select DTS when connecting to a DTS Decoder.
1. With the unit in Stop mode, press the MENU button.
Dynamic Compression
1. On : To select dynamic compression.
2. Off : To select the standard range.
3. Select Display Setup using UP/DOWN buttons,
then press the RIGHT or ENTER button.
Still Mode
These options will help prevent picture shake in still
mode and display small text clearer.
2. Select Setup using UP/DOWN buttons, then
RIGHT or ENTER button.
1. Auto : When selecting Auto, Field/Frame mode will be
automatically converted.
2. Field : Select this feature when the screen shakes in
the Auto mode.
3. Frame : Select this feature when you want to see
small letters more clearly in the Auto mode.
PCM Down Sampling
1. On : Select this when the amplifier connected to the
player is not 96KHz compatible. In this case, the
96KHz signals will be down converted to 48KHZ.
Screen Messages
Use to turn on-screen messages On or Off.
2. Off : Select this when the amplifier connected to the
player is 96KHz compatible. In this case, all
signals will be output without any changes.
4. Use the UP/DOWN buttons to select the desired
item. Then press the RIGHT or ENTER button.
AUDIO SETUP
Dolby Digital OutputII
: PCM
MPEG-2 Digital OutII
: PCM
DTSIIIII
: Off
Dynamic Compression I
: On
PCM Down Sampling II
: On
Note
• How to make the SETUP menu disappear or
return to menu screen during set up;
Press RETURN or LEFT button.
• Manufactured under license from Dolby
Laboratories. “Dolby” and the double-D symbol are
trademarks of Dolby Laboratories.
• “DTS” and “DTS Digital Out” are trademarks of
Digital Theater Systems, Inc.
Black Level
Adjusts the brightness of the screen.(On/Off)
TV System
4. Use the UP/DOWN buttons to select the desired
item. Then press the RIGHT or ENTER button.
1. NTSC Disc : In case of using NTSC disc
• If your TV system only has PAL-Video input you
must choose “PAL”. When you choose “PAL”,
Interlace output format is PAL 60 Hz output.
TV Aspect
Depending on the type of television you have, you may
want to adjust the screen setting (aspect ratio).
• If your TV system only has NTSC, input you must
choose “NTSC Output”.
1. 4:3 Letter Box : Select when you want to see the total
16:9 ratio screen DVD supplies, even though you
have a TV with a 4:3 ratio screen. Black bars will
appear at the top and bottom of the screen.
2. PAL Disc : In case of using PAL disc
• If your TV system only has NTSC-Video input, you
must choose “NTSC Output”.
2. 4:3 Pan Scan : Select this for conventional size TVs
when you want to see the central portion of the 16:9
screen. (Extreme left and right side of movie picture
will be cut off.)
• If your TV system only has PAL input, you must
choose “PAL Output”.
3. 16:9 Wide : You can view the full 16:9 picture on your
widescreen TV.
Dolby Digital Output
1. PCM : Converts to PCM(2CH) 48kHz audio. Select
PCM when using the Analog Audio Outputs.
DISPLAY SETUP
TV AspectIII
Still ModeIII
DISPLAY SETUP
2. Bitstream : Converts to Dolby Digital Bitstream
(5.1CH). Select Bitstream when using the
Digital Audio Output.
Note • Be sure to select the correct Digital Output or
no audio will be heard.
Note • When Multi Channel Output select Digital.
Dolby & MPEG-2 Digital Out works.
TV AspectIII
: 4:3 L-Box
Still ModeIII
: Auto
Screen MessagesI
: On
Black LevelII
: Off
TV SystemIII
Video OutputII
: PAL
: S-Video
MPEG-2 Digital Out
TV ASPECT
1. PCM : Converts to PCM(2CH) audio. Select PCM
when using the Analog Audio Outputs.
4:3 Letter Box
4:3 Pan Scan
2. Bitstream : Converts to MPEG-2 Digital Bitstream
(5.1CH or 7.1CH). Select Bitstream when
using the Digital Audio Output.
16:9 Wide
ENG-26
ENG-27
: 4:3 L-Box
: Auto
Screen MessagesI
: On
Black LevelII
: Off
TV SystemIII
Video OutputII
: PAL
: S-Video
Setting Up the Display Options
Video Output
Select Video Output.
1. S-Video : Select when you want to use Video and
S-Video Out.
2. Component (I-SCAN) : Select when you want to use
Component Interlace
(625i/525i) Out.
3. Component (P-SCAN) : Select when you want to use
Component Progressive
(625p/525p) Out.
4. SCART Output : Select when you want to use Scart
Out.
Setting Up the Parental Control
The Parental Control function works in conjunction
with DVDs that have been assigned a rating - which
helps you control the types of DVDs that your family
watches. There are up to 8 rating levels on a disc.
Setting Up the Parental Control
CREATE PASSWORD
Re-enter Password
- - - -
1. With the unit in Stop mode, press the MENU button.
2. Select Setup using UP/DOWN buttons, then
RIGHT or ENTER button.
0~9
RETURN
3. Select Parental Setup using UP/DOWN buttons,
then press the RIGHT or ENTER button.
• RGB : Select when you want to use SCART RGB
Out.
• S-Video : Select when you want to use SCART
S-Video Out.
• Video : Select when you want to use SCART
Video Out.
6. Select the Rating Level you want using
UP/DOWN buttons. For example, if you select up
to Level 6, discs that contain Level 7, 8 will not
play.
- To cancel the Rating Level, select No using RIGHT or
ENTER in Use Password.
* If the Yes/No selection in the Display Setup sub
Menu is not made within 10 seconds, the screen
returns to the previous menu.
DISPLAY SETUP
TV AspectIII
Still ModeIII
: 4:3 L-Box
: Auto
Screen MessagesI
: On
Black LevelII
: Off
TV SystemIII
Video OutputII
: PAL
: S-Video
Setting Up the Rating Level
4. Use RIGHT or ENTER to select Yes if you want
to use a password. The Enter Password screen
appears.
PARENTAL SETUP
Use PasswordII
ENTER
: NoII
RETURN
About the Change Password;
MENU
- Highlight Change Password using UP/DOWN buttons.
- Press ENTER button.
The Change Password screen appears.
- Enter your new password. Enter the new password again.
Component (P-SCAN)
S-Video
Video
5. Enter your password. The Re-enter Password
screen appears to confirm the password.
Enter your password again.
The player is locked ( ).
CREATE PASSWORD
Important Note
• Consult your TV User’s Manual to find out if your
TV supports Progressive Scan. If Progressive
Scan is supported, follow the TV User’s Manual’s
instructions regarding Progressive Scan settings in
the TV’s menu system.
• If the screen is blocked by setting the wrong Video
Output, see page 30.
3. Select Parental Setup using UP/DOWN buttons,
then press the RIGHT or ENTER button.
4. Enter your password.
The Parental Setup screen appears.
Enter Password
PASSWORD CHECK
- - - -
0~9
RATING LEVEL
Level 8 Adult
Level 7
Level 6
Level 5
Level 4
Level 3
Level 2
Level 1 Kids Safe
2. Select Setup using UP/DOWN buttons, then
RIGHT or ENTER button.
The player is locked ( ).
Component (I-SCAN)
RGB
e.g) Setting up in LEVEL6.
1. With the unit in Stop mode, press the MENU button.
DISPLAY SETUP
S-Video
SCART Output
5. Select Rating Level using UP/DOWN buttons,
and press ENTER or RIGHT button.
RETURN
Note
• How to make the SETUP menu disappear or
return to menu screen during set up;
Press RETURN or LEFT button.
• If you have forgotten your password, see Forgot
Password in the Troubleshooting Guide.
Enter Password
- - - -
0~9
ENG-28
RETURN
ENG-29
Troubleshooting
Specifications
Before requesting service (troubleshooting), please check the following.
Problem
No operations can be
performed with the remote.
Action
• Check the batteries in the remote. They may need replacing.
• Operate the remote control at a distance of no more than 20 feet.
• Remove batteries and hold down one or more buttons for several
minutes to drain the microprocessor inside the remote to reset it.
Reinstall batteries and try to operate the remote again.
Disc does not play.
• Ensure that the disc is installed with the label side facing up.
• Check the region number of the DVD.
5.1 channel sound is not
being reproduced.
• 5.1 channel sound is reproduced only when the following conditions are met. :
1) The DVD player is connected with the proper amplifier
2) The disc is recorded with 5.1 channel sound.
• Check whether the disc being played has the “Dolby 5.1 ch” mark
on the outside.
• Check if your audio system is connected and working properly.
• In a SETUP Menu, is the Audio Output set to Bitstream?
The
icon appears on
screen.
• The features or action cannot be completed at this time because:
1. The DVD’s software restricts it.
2. The DVD’s software doesn’t support the feature (e.g., angles).
3. The feature is not available at the moment.
4. You’ve requested a title or chapter number or search time that
is out of range.
Page
General
Disc
Reading Speed : 3.49 ~ 4.06 m/sec.
Approx. Play Time
(Single Sided, Single Layer Disc) : 135 min.
Reading Speed : 4.8 ~ 5.6 m/sec.
Maximum Play Time : 20 min.
P26
Composite Video
SCART Jack
P11
Video
Output
P27
No audio.
• Make sure you have selected the correct Digital Output in the
Audio Options Menu.
P26
ENG-30
10 % to 75 %
CD : 8Cm
(COMPACT DISC)
• The Screen Ratio is fixed on your DVDs.
• Go to the contents and find the section of the instruction book that
contains the explanations regarding the current problem, and follow
the procedure once again.
• If the problem still cannot be solved, please contact your nearest
authorized service center.
+5°C to +35°C
P9
The screen ratio cannot
be changed.
If you experience other
problems.
430mm (W) X 205mm (D) X 50mm (H)
Reading Speed : 4.8 ~ 5.6 m/sec.
Maximum Play Time : 74 min.
• Some of the functions selected in the Setup Menu may not work
properly if the disc is not encoded with the corresponding function.
• Press power on from a cold start with no disc in the unit. Press the
STOP (
) and PLAY (
) buttons simultaneously on the front
panel for three seconds. The SELECT MENU LANGUAGE display
will appear. Select the number button of the desired language.
Press the MENU button, and then press DOWN button to select
the Parental Setup. The Parental Setup is now unlocked as
indicated on the display. You can change your password.
1.8 Kg
Dimensions
CD : 12Cm
(COMPACT DISC)
Play mode differs from the
Setup Menu selection.
Forgot password
12 W
Weight
DVD
(DIGITAL VERSATILE DISC)
P5
• Check if the disc has a Menu.
• Press power on from a cold start with no disc in the unit. Press the
STOP (
) and PLAY (
) buttons simultaneously on the front
panel for three seconds. The SELECT MENU LANGUAGE display
will appear. Select the number button of the desired language.
AC 230 V, 50 Hz
Power Consumption
Operating Temperature Range
Operating Humidity Range
P3
Disc Menu doesn’t appear.
The screen is blocked
Power Requirements
Component Video
P23~29
S-VIDEO
SCART Jack
P28
P28~29
2 channel
Audio
Output
*Frequency Response
1 channel : 1.0 Vp-p (75 Ω load)
R(Red) : 0.7 Vp-p (75 Ω load)
G(Green) : 0.7 Vp-p (75 Ω load)
B(Blue) : 0.7 Vp-p (75 Ω load)
Composite Video : 1.0 Vp-p (75 Ω load)
Luminance Signal : 1.0 Vp-p (75 Ω load)
Color Signal : 0.3 Vp-p (75 Ω load)
Y : 1.0 Vp-p (75 Ω load)
Pr : 0.70 Vp-p (75 Ω load)
Pb : 0.70 Vp-p (75 Ω load)
Luminance Signal : 1.0 Vp-p (75 Ω load)
Chrominance Signal : 0.3 Vp-p (75 Ω load)
2 Channel : L(1/L), R(2/R)
L(1/L), R(2/R)
48 kHz Sampling : 4 Hz to 22 kHz
96 kHz Sampling : 4 Hz to 44 kHz
*S/N Ratio
110 dB
*Dynamic Range
100 dB
*Total Harmonic Distortion
0.004 %
*: Nominal specification
• Samsung Electronics Co., Ltd reserves the right to change the specifications without notice.
• Weight and dimensions are approximate.
ENG-31
Download PDF