Samsung | P63FP-2 | Samsung Plasma-Display P63FP-2 Benutzerhandbuch

SyncMaster P50HP, P50HP-2, P63FP, P63FP-2
PDP Display
User Manual
The color and the appearance may differ depending on the
product, and the specifications are subject to change
without prior notice to improve the performance.
Safety Instructions
Notational
Note
These safety instructions must be followed to ensure your safety and prevent property damage.
Make sure to read the instructions carefully and use the product in the correct manner.
Warning / Caution
Failure to follow directions noted by this symbol could result in bodily
harm or damage to the equipment.
Note
Prohibited
Important to read and understand at all times
Do not disassemble
Disconnect the plug from the
outlet
Do not touch
Ground to prevent an electric
shock
Power
When not used for extended period of time, set your computer to DPM.
If using a screen saver, set it to active screen mode.
The images here are for reference only, and are not applicable in all cases
(or countries).
Shortcut to Anti-Afterimage Instructions
Do not use a damaged power cord or plug or a damaged or
loose power outlet.
•
Otherwise, this may result in electric shock or fire.
Do not touch the power plug with wet hands when removing or
plugging the plug into the outlet.
•
Otherwise, this may result in electric shock.
Make sure to connect the power cord to a grounded power outlet.
•
Otherwise, it may result in electric shock or personal injury.
1
Safety Instructions
Ensure that the power plug is plugged into the power outlet
firmly and correctly.
•
Otherwise, this may result in fire.
Do not forcefully bend or pull the power plug and do not place
any heavy material on it.
•
Otherwise, this may result in fire.
Do not connect multiple appliances to the same power outlet.
•
Otherwise, this may cause fire due to overheating.
Do not disconnect the power cord while using the product.
•
Otherwise, this may result in damage to the product due to
electric shock.
To disconnect the apparatus from the mains, the plug must be
pulled out from the mains socket, therefore the mains plug shall
be readily operable.
•
Otherwise, this may cause electric shock or fire.
Use only the power cord provided by our company. Do not use
the provided power cord of another product.
•
Otherwise, this may result in fire or electric shock.
Installation
Be sure to contact an authorized Service Center when installing your
monitor in a location with heavy dust, high or low temperatures, high humidity, and exposed to chemical substances and where it operates for 24
hours such as at airports, train stations etc.
Failure to do so may cause serious damage to your monitor.
Ensure that at least two persons lift and move the product.
•
Otherwise, it may be dropped and cause personal injury, and/
or damage the product.
When installing the product in a cabinet or rack, make sure that
the front end of the bottom of the product does not project out.
•
Otherwise, it may fall or cause personal injury.
•
Use a cabinet or rack of a size appropriate to the product.
DO NOT PLACE CANDLES, MOSQUITO REPELLANT, CIGARETTES AND ANY HEATING APPLIANCES NEAR THE PRODUCT.
•
Otherwise, this may result in fire.
2
Safety Instructions
Keep heating appliances as far away from the power cord or the
product as possible.
•
Otherwise, this may result in electric shock or fire.
Do not install it in a badly ventilated location such as a bookcase
or closet.
•
Otherwise, this may result in fire due to an increase in the internal temperature.
When putting the product down, make sure to put it down softly.
•
Otherwise, this may result in damage to the screen display.
Do not place the front of the product on the floor.
•
Otherwise, this may result in damage to the screen display.
Ensure that an authorized installation company installs the wall
mount.
•
Otherwise, it may fall and cause personal injury.
•
Make sure to install the specified wall mount.
Install your product in a well ventilated location. Ensure that
there is a clearance of more than 4 inches (10 cm) from the wall.
•
Otherwise, it may result in fire due to an increase in the internal
temperature.
Ensure that the packaging vinyl is kept away from children.
•
Otherwise, it may result in serious harm (suffocation) if children
play with it.
If the height of your monitor is adjustable, do not place any object or part of your body on the stand when lowering it.
•
This may cause damage to the product or the person carrying
it.
Clean
When cleaning the PDP Display case or the surface of the TFT-PDP
screen, wipe with a slightly moistened, soft fabric.
Do not spray cleaner directly onto the surface of the product.
•
Otherwise, this may result in the discoloration and distortion of
the structure and the screen surface may peel off.
Clean the product using a soft cloth with a monitor cleaner only.
•
If you must use a cleaner other than the monitor cleaner, dilute
it with water at a ratio of 1:10.
3
Safety Instructions
When cleaning the power plug pins or dusting the power outlet,
clean it with a dry cloth.
•
Otherwise, it may result in fire.
When cleaning the product, make sure to disconnect the power
cord.
•
Otherwise, it may result in electric shock or fire.
When cleaning the product, disconnect the power cord and
clean it with a soft, dry cloth.
•
Do not use chemicals such as wax, benzene, alcohol, thinner,
mosquito repellant, lubricant, or cleaner.
•
These may change the appearance of the product surface and
peel off the indication labels on the product.
Since the product housing is easily scratched, make sure to use
the specified cloth only.
When cleaning the product, do not spray water directly onto the
main body of the product.
•
Ensure that water does not enter the product and that it is not
wet.
•
Otherwise, this may result in electric shock, fire or a malfunction.
Others
The product is a high voltage product. Do not disassemble, repair or modify the product yourself.
•
Otherwise, this may result in electric shock or fire.
•
If the product needs to be repaired, contact a Service Center.
If there is a strange smell or a strange sound or smoke is coming
from the product, disconnect the power plug immediately and contact a Service Center.
•
Otherwise, this may result in electric shock or fire.
Do not place this product in a location exposed to moisture, dust,
smoke, water, or in a car.
•
Otherwise, this may result in electric shock or fire.
When you drop the product or the case is broken, turn the power
off and disconnect the power cord. Contact a Service Center.
•
Otherwise, this may result in electric shock or fire.
4
Safety Instructions
If thunder or lightning is occurring, do not touch the power cord
or antenna cable.
•
Otherwise, this may result in electric shock or fire.
Do not try to move the monitor by pulling only the wire or the
signal cable.
•
Otherwise, it may fall and result in electric shock, damage to
the product or fire due to damage to the cable.
Do not lift or move the product back and forwards or right and
left while only holding the power cord or signal cables.
•
Otherwise, it may fall and result in electric shock, damage to
the product or fire due to damage to the cable.
Make sure that the ventilating opening is not blocked by a table
or curtain.
•
Otherwise, it may result in fire due to an increase in the internal
temperature.
Do not place any containers containing water, vases, flowerpots, medicines as well as any metal on the product.
•
If water or a foreign material enters the product, disconnect the
power cord and contact a Service Center.
•
This may result in a product malfunction, electric shock, or fire.
Do not use or keep combustible spray or flammable material
near the product.
•
Otherwise, this may result in an explosion or fire.
Do not insert any metal, such as chopsticks, coins, pins and
steel, or flammable objects, such as matches or paper, inside the
product (through the ventilating openings, input and output terminals, etc).
•
If water or foreign material enters the product, disconnect the
power cord and contact a Service Center.
•
Otherwise, this may result in electric shock or fire.
When using a fixed screen for a long time, an afterimage or stain
may occur.
•
If you are not using your product for a long period of time, put
it into sleep mode or use a moving screen saver.
Set a resolution and frequency appropriate to the product.
•
Otherwise, your eyesight may be damaged.
When using headphones or earphones, do not turn the volume
too high.
•
Having the sound too loud may damage your hearing.
5
Safety Instructions
To avoid eyestrain, do not sit too close to the product.
Take a rest for at least five (5) minutes after using the monitor
for one (1) hour.
•
This reduces eye fatigue.
Do not install it in an unstable location such as an unstable rack
or uneven surface or a location exposed to vibrations.
•
Otherwise, it may fall and cause personal injury and/or damage
the product.
•
If you use the product in a location exposed to vibrations, it may
damage the product and result in fire.
When moving the product, turn the power off and disconnect
the power plug, antenna cable, and all the cables connected to the
product.
•
Otherwise, it may result in electric shock or fire.
Ensure that children do not hang onto the product or climb up
onto the product.
•
The product may fall and cause personal injury or death.
If you do not use the product for a long period of time, disconnect
the power cord from the power outlet.
•
Otherwise, this may result in overheating or fire due to dust,
and may result in fire due to electric shock or leakage.
Do not place any heavy items or toys or confectionery, such as
cookies etc. that may attract the attention of children and to the
product.
•
Your children may hang onto the product causing it to fall and
this may result in personal injury or death.
Be careful that children do not place the battery in their mouths
when removed from the remote control. Place the battery in a location that children or infants cannot reach.
•
If children have had the battery in their mouths, consult your
doctor immediately.
When replacing the battery, insert it with the right polarity (+, -).
•
Otherwise, the battery may become damaged or it may cause
fire, personal injury or damage due to leakage of the internal
liquid.
Use only the specified standardized batteries, and do not use a
new battery and a used battery at the same time.
•
Otherwise, the batteries may be damaged or cause fire, personal injury or damage due to a leakage of the internal liquid.
6
Safety Instructions
The batteries (and rechargeable batteries) are not ordinary refuse and must be returned for recycling purposes. The customer
is responsible for returning the used or rechargeable batteries for
recycling.
•
The customer can return used or rechargeable batteries to a
nearby public recycling center or to a store selling the same
type of the battery or rechargeable battery.
Do not place the product in a location exposed to direct sunlight
or near any heat such as a fire or heater.
•
This may reduce the lifetime of the product, and may result in
fire.
Do not drop any objects onto the product or cause any impact
to the product.
•
Otherwise, this may result in electric shock or fire.
Do not use a humidifier near the product.
•
Otherwise, this may result in electric shock or fire.
When there is a gas leak, do not touch the product or the power
plug; ventilate immediately.
•
If a spark occurs, it may cause an explosion or fire.
If the product has been turned on for a long time, the display
panel becomes hot. Do not touch it.
Keep the small accessories in a location out of the reach of children.
Be careful when adjusting the angle of the product or the height
of the stand.
•
This may result in personal injury as your hand or fingers may
become caught.
•
Also, if you tilt the product too far, it may fall and cause personal
injury.
Do not install the product in a location low enough for children
to reach.
•
Otherwise, it may fall and result in personal injury.
•
Since the front part of the product is heavy, install the product
on a level and stable surface.
7
Safety Instructions
Do not put any heavy objects on the product.
•
This may result in personal injury and/or damage to the product.
8
Introduction
Package Contents
Note
Please make sure the following items are included with your PDP Display.
If any items are missing, contact your dealer.
Contact a local dealer to buy optional items.
Checking the Contents of the Package
Remove the lock from the package box, as shown in the figure above.
Lift up the package box by Check the contents of the
holding the grooves on
package.
both sides of the package
box.
Remove the Styrofoam
and vinyl cover.
Note
•
After unpacking the package, make sure to check the contents of the package.
•
Make sure to keep the package box for transporting the product in the future.
•
After unpacking, you may use the lower part of the package box as a temporary stand for
product test or operation check.
Unpacking
9
Introduction
PDP Display
Manuals
Quick Setup Guide
Warranty Card
User's Guide
(Not available in all locations)
Cables
Power Cord
D-Sub Cable
Remote Control
Batteries (AAA X 2)
Others
(Not available in all locations)
Ferrite Core for Power
Cord
Sold separately
DVI Cable
Wall Mount KIT
Network Box
RGB to BNC Cable
BNC to BNC Cable
Ferrite Core
•
The ferrite cores are used to shield the cables from interference.
•
When connecting a cable, open the ferrite core and clip it
around the cable near the plug.
10
Introduction
Your PDP Display
Note
The PDP device may interfere with an amateur radio or AM radio.
Front
SOURCE button [SOURCE]
Switches from PC mode to Video mode. Changing the source is only allowed for external devices that are connected to the PDP Display at the
time.
[PC] → [DVI] → [AV] → [HDMI] → [MagicInfo] → [BNC] → [Component]
Note
•
MagicInfo can only be enabled when a network box is connected.
•
The HDMI port and network box cannot be connected at the same time.
Enter button [ ]
Activates a highlighted menu item.
MENU button [MENU]
Opens the on-screen menu and exits from the menu. Also use to exit the
OSD menu or return to the previous menu.
- VOL+
Moves from one menu item to another horizontally or adjusts selected
menu values. When OSD is not on the screen, push the button to adjust
volume.
SEL
Moves from one menu item to another vertically or adjusts selected menu
values.
Power button [
]
Use this button for turning the PDP Display on and off.
Power indicator
Shows PowerSaver mode by blinking green
11
Introduction
Note
See PowerSaver described in the manual for further information regarding
power saving functions. For energy conservation, turn your PDP Display
OFF when it is not needed or when leaving it unattended for long periods.
Remote Control Sensor
Aim the remote control towards this spot on the PDP Display.
Rear
Note
For detailed information concerning cable connections, refer to Connecting Cables under
Setup. The PDP Display's configuration at the back may vary slightly depending on the PDP
Display model.
POWER IN
The power cord plugs into the PDP Display
and the wall plug.
12
Introduction
RS232C OUT/IN (RS232C Serial PORT)
MDC(Multiple Display Control) Program Port
RGB IN (PC Connection Terminal (Input))
•
Use a D-Sub Cable (15 pin D-Sub) - PC
mode (Analog PC)
•
Connect the RGB IN port on the monitor
to the BNC port on the PC using the RGB
to BNC cable.
DVI IN (PC Video Connection Terminal)
Connect the [DVI IN] port on the monitor to
the DVI port on the PC using the DVI cable.
DVI/RGB AUDIO IN (PC/DVI Audio Connection Terminal (Input))
L]
AV/COMPONENT AUDIO IN [R-AUDIO-
Connect the port of the DVD, VCR (DVD /
DTV Set-Top Box) to the [R-AUDIO-L] port
of the PDP Display.
DVI OUT
•
Connect a monitor to another monitor
through a DVI cable.
•
Connect the [DVI OUT] port on the monitor to the [HDMI IN] port on the other
monitor using the DVI to HDMI cable.
•
DVI, HDMI and network signals sent via
the [DVI OUT] port are displayed on the
second display which has the DVI IN port.
Note
Up to 6 Full HD or 10 HD monitors can be
connected (May differ depending on the
product).
13
Introduction
AV IN [VIDEO]
Connect the AV IN [VIDEO] terminal of your
monitor to the video output terminal of the
external device using a VIDEO cable.
AUDIO OUT
Headphone/External speaker output terminal.
HDMI IN
Connect the HDMI terminal at the back of
your PDP Display to the HDMI terminal of
your digital output device using a HDMI cable.
Up to HDMI cable 1.2 can be supported.
BNC OUT [R, G, B, H, V] (BNC Terminal
(Output))
BNC (Analog PC) Connection: connecting
the R, G, B, H, V ports.
The number of PDP Displays that can be
connected to the loopout depends on the cables, signal source, etc. With cables or signal
source where there is no degradation, up to
10 PDP Displays can be connected (May not
be supported depending on the connected
cable).
BNC/COMPONENT IN [R/PR, G/Y, B/
PB, H, V] (BNC/Component Connection Terminal (input))
- During BNC input, please check specifications for the input ports below.
•
[R/PR] --> Red port input
•
[G/Y] --> Green port input
•
[B/PB] --> Blue port input
- During component input, please check
specifications for the input ports below.
•
[R/PR] --> Red port input
•
[G/Y] --> Green port input
•
[B/PB] --> Blue port input
14
Introduction
Kensington Lock
The Kensington Lock is a device used to
physically fix the system when using it in a
public place. The locking device has to be
purchased separately. The appearance and
locking method may differ from the illustration depending on the manufacturer. Refer to
the manual provided with the Kensington
Lock for proper use.
Note
The location of the Kensington Lock may be
different depending on its model.
Using the Anti-Theft Kensington Lock
1.
Insert the locking device into the Kensington slot on the Monitor
it in the locking direction
and turn
.
2.
Connect the Kensington Lock cable.
3.
Fix the Kensington Lock to a desk or a
heavy stationary object.
Note
See Connecting Cables for further information regarding cable connections.
Remote Control
Note
The performance of the remote control may be affected by a TV or other electronic device
operating near the PDP Display , causing a malfunction due to interference with the frequency.
15
Introduction
POWER
OFF
Number Buttons
DEL
/ GUIDE button
- VOL +
SOURCE
D.MENU
TOOLS
Up-Down Left-Right buttons
INFO
COLOR BUTTONS
TTX/MIX
MTS/DUAL
ENTER/PRE-CH
MUTE
CH/P
TV
MENU
RETURN
EXIT
MagicInfo
1.
POWER
Turns the product On.
2.
OFF
Turns the product Off.
3. Number Buttons
4. DEL
ton
/ GUIDE but-
Used to enter the password during the OSD adjustment or
to use MagicInfo.
The "-" button is used to select Digital channels.
Electronic Program Guide (EPG) display.
- This button is disabled for this PDP display.
5. - VOL +
Adjusts the audio volume.
6.
SOURCE
Press this button to switch to MagicInfo or PC mode or a
connected external input source.
7.
D.MENU
DTV menu display
- This button is disabled for this PDP display.
8. TOOLS
Use to quickly select frequently used functions.
- This button is disabled for this PDP display.
16
Introduction
9. Up-Down Left-Right buttons
Moves from one menu item to another horizontally, vertically
or adjusts selected menu values.
10.
INFO
Current picture information is displayed on the upper left
corner of the screen.
11. COLOR BUTTONS
Press to add or delete channels and to store channels to the
favorite channel list in the “Channel List” menu.
- This button is disabled for this PDP display.
TTX/MIX
12.
TV channels provide written information services via teletext.
- Teletext Buttons
- This button is disabled for this PDP display.
13. MTS/DUAL
- This function does not work for this PDP Display.
MTSYou can select MTS (Multichannel Television Stereo) mode.
FM Stereo
Audio Type
MTS/S_Mode
Default
Mono
Mono
Stereo
Mono ↔ Stereo
Manual
Change
SAP
Mono ↔ SAP
Mono
DUALSTEREO/MONO, DUAL l / DUAL ll and MONO/NICAM
MONO/NICAM STEREO can be operated depending on the
broadcasting type by using the DUAL button on the remote
control while watching TV.
ENTER/PRE-CH
14.
This button is used to return to the immediately previous
channel.
- This button is disabled for this PDP display.
15.
MUTE
Pauses (mutes) the audio output temporarily. This is displayed on the lower left corner of the screen. The audio
comes back on if MUTE or - VOL + is pressed in the Mute
mode.
16.
CH/P
In TV mode, selects TV channels.
- This button is disabled for this PDP display.
17. TV
Selects the TV mode directly.
- This button is disabled for this PDP display.
18. MENU
Opens the on-screen menu and exits from the menu or
closes the adjustment menu.
19.
Returns to the previous menu.
RETURN
17
Introduction
20.
EXIT
21. MagicInfo
Exits from the menu screen.
MagicInfo Quick Launch Button.
Note
This button is disabled for products that do not support
MagicInfo.
Mechanical Layout(P50HP, P50HP-2)
Mechanical Layout
PDP Display Head
Installation VESA Bracket
•
When installing VESA, make sure to comply with the international VESA standards.
•
Purchasing VESA Bracket and Installation Information : Please contact your nearest
SAMSUNG Distributor to place an order. After your order is placed, installation professionals will visit you and install the bracket.
18
Introduction
•
At least 2 persons are needed in order to move the PDP Display.
•
SAMSUNG is not responsible for any product damage or any injury caused by installation
at customer's discretion.
Dimensions
Notice
For securing the bracket on a wall, use only machine screws of 6 mm diameter and 8 to 12
mm length.
Wall Bracket Installation
•
Contact a technician for installing the wall bracket.
•
SAMSUNG Electronics is not responsible for any damages to the product or harm to
customers when the installation is done by the customer.
•
This product is for installing on cement walls. The product may not stay in place when
installed on plaster or wood.
Components
Only use the components and accessories shipped with the product.
Wall Bracket(1)
Hinge(Left 1, Right Plastic Screw
1)
Hanger (A)(11)
(4)
19
Screw
(B)(4)
Anchor
(11)
Introduction
Wall Bracket Assembly
Note
There are two hinges(left and right). Use the correct one.
1.
Insert and tighten the Captive Screw in the direction of the arrow.
When done, mount the wall bracket on the wall.
2.
A-
Captive Screw
B-
Wall Bracket
C-
Hinge (Left)
D-
Hinge (Right)
Before drilling into the wall, check if the length between the two locking holes at the back
of the product is correct.
If the length is too short or long, loosen all or some of the 4screws on the wall bracket to
adjust the length.
A3.
Length between the two locking holes
Check the installation diagram and mark the drill points on the wall. Use the 5.0 mm bit
to drill holes deeper than 35 mm. Fix each anchor in the corresponding hole. Match each
20
Introduction
of the brackets and hinge holes to the corresponding anchor holes and insert and tighten
the 11 screws A.
To mount the product on the wall bracket
The shape of the product may vary depending on the model. (The assemblies of the plastic
hanger and the screw are the same)
1.
Remove the 4 screws on the back of the product.
2.
Insert the screw B into the plastic hanger.
Notice
3.
•
Mount the product on the wall bracket and make sure it is properly fixed to the left
and right plastic hangers.
•
Be careful when installing the product on the bracket as fingers can be caught in the
holes.
•
Make sure the wall bracket is securely fixed to the wall, or the product may not stay
in place after installation.
Tighten the 4 screws in step 2 (plastic hanger + screw B)to the rear holes of the product.
21
Introduction
4.
Remove safety pin (3) and insert the 4 product holders into the corresponding bracket
holes (1). Then place the product(2) so that it is firmly fixed to the bracket. Make sure to
re-insert and tighten the safety pin (3) to securely hold the product to the bracket.
A-
PDP Display
B-
Wall Bracket
C-
Wall
Wall Bracket Angle Adjustment
Adjust the bracket angle to -2° before installing it on the wall.
1.
Fix the product to the wall bracket.
2.
Hold the product at the top in the center and pull it forward (direction of the arrow) to
adjust the angle.
Note
You can adjust the bracket angle between -2° and 15°.
22
Introduction
Make sure to use the top center, and not the left or the right side of the product to adjust the
angle.
Mechanical Layout(P63FP, P63FP-2)
Mechanical Layout
PDP Display Head
Installation VESA Bracket
•
When installing VESA, make sure to comply with the international VESA standards.
23
Introduction
•
Purchasing VESA Bracket and Installation Information : Please contact your nearest
SAMSUNG Distributor to place an order. After your order is placed, installation professionals will visit you and install the bracket.
•
At least 2 persons are needed in order to move the PDP Display.
•
SAMSUNG is not responsible for any product damage or any injury caused by installation
at customer's discretion.
Dimensions
Notice
For securing the bracket on a wall, use only machine screws of 6 mm diameter and 8 to 12
mm length.
Wall Bracket Installation
•
Contact a technician for installing the wall bracket.
•
SAMSUNG Electronics is not responsible for any damages to the product or harm to
customers when the installation is done by the customer.
•
This product is for installing on cement walls. The product may not stay in place when
installed on plaster or wood.
Components
Only use the components and accessories shipped with the product.
Wall Bracket(1)
Hinge(Left 1, Right Plastic Screw
1)
Hanger (A)(11)
(4)
24
Screw
(B)(4)
Anchor
(11)
Introduction
Wall Bracket Assembly
Note
There are two hinges(left and right). Use the correct one.
1.
Insert and tighten the Captive Screw in the direction of the arrow.
When done, mount the wall bracket on the wall.
2.
A-
Captive Screw
B-
Wall Bracket
C-
Hinge (Left)
D-
Hinge (Right)
Before drilling into the wall, check if the length between the two locking holes at the back
of the product is correct.
If the length is too short or long, loosen all or some of the 4screws on the wall bracket to
adjust the length.
A3.
Length between the two locking holes
Check the installation diagram and mark the drill points on the wall. Use the 5.0 mm bit
to drill holes deeper than 35 mm. Fix each anchor in the corresponding hole. Match each
25
Introduction
of the brackets and hinge holes to the corresponding anchor holes and insert and tighten
the 11 screws A.
To mount the product on the wall bracket
The shape of the product may vary depending on the model. (The assemblies of the plastic
hanger and the screw are the same)
1.
Remove the 4 screws on the back of the product.
2.
Insert the screw B into the plastic hanger.
Notice
3.
•
Mount the product on the wall bracket and make sure it is properly fixed to the left
and right plastic hangers.
•
Be careful when installing the product on the bracket as fingers can be caught in the
holes.
•
Make sure the wall bracket is securely fixed to the wall, or the product may not stay
in place after installation.
Tighten the 4 screws in step 2 (plastic hanger + screw B)to the rear holes of the product.
26
Introduction
4.
Remove safety pin (3) and insert the 4 product holders into the corresponding bracket
holes (1). Then place the product(2) so that it is firmly fixed to the bracket. Make sure to
re-insert and tighten the safety pin (3) to securely hold the product to the bracket.
A-
PDP Display
B-
Wall Bracket
C-
Wall
Wall Bracket Angle Adjustment
Adjust the bracket angle to -2° before installing it on the wall.
1.
Fix the product to the wall bracket.
2.
Hold the product at the top in the center and pull it forward (direction of the arrow) to
adjust the angle.
Note
You can adjust the bracket angle between -2° and 15°.
27
Introduction
Make sure to use the top center, and not the left or the right side of the product to adjust the
angle.
28
Connections
Connecting a Computer
There are several ways to connect the computer to the monitor. Choose
one from the following options.
Using the D-sub (Analog) connector on the video card.
•
Connect the D-sub to the 15-pin, [RGB IN] port on the back of your PDP
Display and the 15 pin D-sub Port on the computer.
Using the DVI (Digital) connector on the video card.
•
Connect the DVI Cable to the [DVI IN] port on the back of your PDP
Display and the DVI port on the computer.
29
Connections
Using the HDMI (digital) output on the graphics card.
•
Connect the [HDMI IN] port on the PDP Display to the HDMI port on
the PC using the HDMI cable.
Note
When the HDMI cable to the PC, ensure that you select HDMI from both
the Source List and Edit Name before selecting PC or DVI device so that
normal PC screen and sound can be outputted. Note that sound is only
available when connected according to the option
that follows.
Using the BNC (Analog) connector on the video card.
•
Connect the [BNC/COMPONENT IN] port on the monitor to the BNC
port on the PC using the BNC to BNC cable.
30
Connections
Connect the audio cable for your PDP Display to the audio port on the back
of the PDP Display.
Connect the power cord for your PDP Display to the power port on the
back of the PDP Display. .
Note
•
Turn on both your computer and the PDP Display.
•
Contact a local SAMSUNG Electronics Service Center to buy optional items.
Connecting to Other devices
•
AV input devices such as DVD players, VCRs or camcorders as well as your computer
can be connected to the PDP Display. For detailed information on connecting AV input
devices, refer to the contents under Adjusting Your PDP Display.
•
The PDP Display's configuration at the back may vary slightly depending on the PDP
Display model.
Connecting AV Devices
31
Connections
1.
Connect an audio cable to the audio output port on the external device and [AV/COMPONENT AUDIO IN[R-AUDIO-L]] port on the monitor, and connect the video output port
on the external device to the [AV IN [VIDEO]] port on the monitor.
2.
Play the DVD, VCR or Camcorder with a DVD disc or tape inserted.
3.
Select AV using the SOURCE button on the front of the PDP display or on the remote.
Connecting to a Camcorder
1.
Locate the AV output jacks on the camcorder. They are usually found on the side or back
of the camcorder. Connect a set of audio cables between the AUDIO OUTPUT jacks on
the camcorder and the [AV/COMPONENT AUDIO IN [R-AUDIO-L]] on the PDP Display .
2.
Connect a video cable between the VIDEO OUTPUT jack on the camcorder and the [AV
IN [VIDEO]] on the PDP Display .
3.
Select AV for the Camcorder connection using the SOURCE button on the front of the
PDP Display or on the remote control.
4.
Then, start the Camcorder with a tape inserted.
Note
The audio-video cables shown here are usually included with a Camcorder. (If not, check
your local electronics store.) If your camcorder is stereo, you need to connect a set of two
cables.
32
Connections
Connecting the BNC to BNC cable
1.
Connect the [BNC/COMPONENT IN [R/PR, G/Y, B/PB]] ports on the monitor to the BNC
port on the external device using the BNC to BNC cable.
2.
Select BNC using the SOURCE button on the front of the PDP Display or on the remote
control.
Connecting Using a DVI Cable
1.
Connect between the [DVI OUT] port on the PDP Display and the input port on another
monitor using a DVI cable.
2.
Connect between the [AUDIO OUT] port on the PDP Display and the audio input port on
another monitor using a stereo cable.
3.
Select DVI using the SOURCE button on the front of the PDP Display or on the remote
control.
Note
DVI OUT does not support HDCP.
33
Connections
Connecting Using a HDMI Cable
1.
Connect input devices such as a Blu-Ray/DVD player to the [HDMI IN] terminal of the
PDP Display using an HDMI cable.
2.
Select HDMI using the SOURCE button on the front of the PDP Display or on the remote
control.
Note
In HDMI mode, only PCM format audio is supported.
Connecting Using a DVI to HDMI Cable
1.
Connect the DVI output terminal of a digital output device to the [HDMI IN] terminal of
the PDP Display using a DVI to HDMI cable.
34
Connections
2.
Connect the red and white jacks of an RCA to stereo (for PC) cable to the same colored
audio output terminals of the digital output device, and connect the opposite jack to the
[DVI / RGB AUDIO IN] terminal of the PDP Display.
3.
Select HDMI using the SOURCE button on the front of the PDP Display or on the remote
control.
Connecting a DVD Player
1.
Connect a set of audio cables between the [AV/COMPONENT AUDIO IN [R-AUDIO-L]]
on the PDP Display and the AUDIO OUT jacks on the DVD player.
2.
Connect a Component cable between the [BNC/COMPONENT IN [R/PR, G/Y, B/PB]]
port on the PDP Display and the PR, Y, PB jacks on the DVD player.
Note
•
Select Component for the connection to a DVD player using the SOURCE button on the
front of the PDP Display or on the remote control.
•
Then, start the DVD Player with a DVD disc inserted.
•
A component cable is optional.
•
For an explanation of Component video, consult your DVD manual.
35
Connections
Connecting a DTV Set Top (Cable/Satellite) Box
1.
Connect a Component cable between the [BNC/COMPONENT IN [R/PR, G/Y, B/PB]]
port on the PDP Display and the PR, Y, PB jacks on the Set Top Box.
2.
Connect a set of audio cables between the [AV COMPONENT AUDIO IN [R-AUDIO-L]]
on the PDP Display and the AUDIO OUT jacks on the Set Top Box.
Note
•
Select Component for the connection to a DTV Set Top Box using the SOURCE button
on the front of the PDP Display or on the remote control.
•
For an explanation of Component video, see your Set Top Box owner's manual.
Connecting to an Audio System
1.
Connect a set of audio cables between the AUX L, R jacks on the AUDIO SYSTEM and
[AUDIO OUT] on PDP Display.
36
Using the Software
MDC
Installation
1.
Insert the installation CD into the CD-ROM drive.
2.
Click the Serial MDC installation program.
Note
If the screen for installing the software does not appear, install it using the Serial MDC
execution file in the MDC folder of the CD-ROM.
3.
If the installation wizard screen does appear, click "Next."
4.
The "License Agreement" screen will appear. Click "Yes."
5.
The "Customer Information" window will appear. Register the user information and click
"Yes."
6.
The "Choose Destination Location" window will appear. Specify the file location to install
to and click "Next."
Note
If the file location is not specified, the program will be installed in the default file location.
7.
The "Start Copying Files" window will appear. Confirm the file location and click "Next."
8.
The installation progress screen will appear.
9.
The "InstallShield Wizard Complete" screen will appear. Click "Finish."
Note
Select " Launch Serial MDC" and click "Finish." The MDC program will immediately be
run.
10. If the installation is successfully completed, the quick Serial MDC execution icon will
appear on the desktop.
MDC execution icon may not appear depending on specification of computer system or monitor. If that happens, press F5 Key.
1
Using the Software
Installation Problems
The installation of MDC can be affected by such factors as the video card, motherboard and
the network environment.
Uninstall
The MDC program can be removed only by using the "Add or Remove Programs" option of
the Windows® Control Panel.
Perform the following steps remove MDC.
Select "Setting/Control Panel" on the "Start" menu and then double-click "Add/Delete a program".
Select Serial MDC from the list and then click the "Add/Delete" button.
Using Serial MDC
2
Introduction
A Multiple Display Control (MDC) is an application allowing various displays to be easily and simultaneously
operated on a PC. RS-232C, a standard of serial communication, is used for the communication between a PC and
a display. Therefore, a serial cable should be connected between the serial port on a PC and the serial port on a
display.
Main Screen
Click Start > Program > Samsung > MDC System to start the program.
Select a set to see the volume of the selected set within the slider.
Main Icons
All
Remote control
Selection Buttons
Safety Lock
Refresh
Port Selection
Display Selection
Lamp Control
Info Grid
Option...
Control Tools
Dropdown Selectors
OSD Display
1.
Use the main icons to switch into each screen.
2.
Allows you to enable or disable the remote control signal receiving function of the display unit.
3.
Set the Safety Lock function.
When setting the Lock function, you can only operate power and lock buttons on the remote control and set.
4.
The setting for the PC Serial Port can change. The original value is COM1.
5.
Selects a Lamp adjustment mode.
6.
Adjusts the number of LFD IDs and the frequency of search repeats.
7.
Defines the range of LFD IDs to display. You can select or deselect the displayed IDs using the Select or Clear
button.
8.
All of the monitors can be selected or deselected.
9.
Selects (Select) or deselects (Clear) LFD IDs displayed by configuring 7 and 8.
10. This searches for monitors. The maximum number is indicated in the Max LFD Id field.
11. Select a display from Display Selection.
12. Use Grid to view brief information on selected display.
13. Use Control Tools to control displays.
14. Switches the OSD function On/Off.
- May not be supported depending on the product.
<Note> The remote control Enable/Disable function operates whether or not the power is On/Off, and this
applies to all displays connected to the MDC. However, regardless of the status at the time the MDC is
shut down, the remote control signal receiving function of all displays is initialized to Enable when the
MDC is closed.
Port Selection
1. The Multiple Display Control is originally set to COM1.
2. If any port other than COM1 is used, COM1 through COM4 can be selected in the Port Selection Menu.
3. If the exact port name that is connected to the LCD Display using a serial cable is not selected, communication will
be unavailable.
4. The selected port is stored in the program and used for the next program as well.
Power Control
1. Click Power Control of the main icons and the Power Control screen appears.
Info Grid shows some basic information necessary to Power Control.
1)
(Power Status)
2) Input
3) Image Size
4) On Timer
5) Off Timer
2. Selects displays you want to adjust using the Select button or checkboxes.
Power Control allows controlling some of the functions of the selected display.
1) Power On/Off
- Turns the power of the selected display On/Off.
2) Volume
- Controls the volume level of the selected display.
It receives the volume value of the selected display from the sets and displays it in the slider.
(If you deselect a single display or all displays, the default value 10 will be restored.)
3)
(Mute On/Off)
- Turns on/off the Mute function of the selected display.
When selecting one set at a time, turn on the Mute function for the selected set.
The Mute function is disabled automatically when you adjust the volume level.
(The values return to the default settings when you undo the selections or choose "Select All".)
The Power Control feature is available for all displays.
The Volume Control and Mute features are available only for the displays whose power status is ON.
3. Selects whether to display the menu screen using the OSD Display menu.
1) Source OSD
- Sets whether the Source OSD will be displayed to indicate when the Source is changed.
2) Not Optimum Mode OSD
- Sets whether the Optimum Mode OSD will be displayed to indicate if the current mode is not supported.
3) No Signal OSD
- Sets whether the No Signal OSD will be displayed to indicate when there is no signal.
4) MDC OSD
- Sets whether the MDC OSD will be displayed to indicate when the settings are changed using the MDC.
Input Source
1. Click Input Source of the main icons and the Input Source control screen appears.
Selects displays you want to adjust using the Select button or checkboxes.
• TV Mode
• PC Mode
Info Grid shows some basic information necessary to Input Source Control.
1)
PC
- Changes the Input Source of the selected display to PC.
2)
BNC
- Changes the Input Source of the selected display to BNC.
3)
DVI
- Changes the Input Source of the selected display to DVI.
4)
TV
- Changes the Input Source of the selected display to TV.
5)
DTV
- Changes the Input Source of the selected display to DTV.
6)
AV
- Changes the Input Source of the selected display to AV.
7)
S-Video
- Changes the Input Source of the selected display to S-Video.
8)
Component
- Changes the Input Source of the selected display to Component.
9)
MagicInfo
- The Input source of MagicInfo works only on MagicInfo model.
10)
HDMI1/HDMI2
- Changes the Input Source of the selected display to HDMI.
11)
DP
- Switches the input source for the selected Display to DP.
12)
Channel
- Channel arrow appears when the Input Source is TV.
HDMI2 may not be supported depending on the product.
DP may not be supported depending on the product.
TV Source can be selected only in products with TV and controlling channels is allowed only when
Input Source is TV.
The Input Source Control feature is available only for the displays whose power status is ON.
Image Size
PC, BNC, DVI, DP
1. Click Image Size of the main icons and the Image Size control screen appears.
Info Grid shows some basic information necessary to Image Size Control.
1)
( Power Status)
- Shows the power status of the current display.
2) Image Size
- Shows the current Image Size of the display in use.
3) Input
- Info Grid displays only the displays whose Input Source is PC, BNC, DVI and DP.
4) PC Source
- Click Image Size in the main menu to display the PC, BNC, DVI and DP tabs.
- The Image Size Control button controls Image Size available for PC, BNC, DVI and DP.
5) Video Source
- Using the Image Size adjustment button, you can adjust the Image Size to a value available in the PC, BNC, DVI
and DP.
DP may not be supported depending on the product.
The Input source of MagicInfo works only on MagicInfo model.
The Input source of TV works only on TV model.
Image Size Control is available only for the displays for which power status is ON.
Image Size
TV, AV, S-Video, Component, DVI(HDCP), HDMI1, HDMI2, DTV.
1. Click Image Size of the main icons and the Image Size control screen appears.
Info Grid shows some basic information necessary to Image Size Control.
1) To adjust Image Size in TV, AV, S-Video, Component, HDMI1, HDMI2 or DTV mode, click the Video Source tab.
Select the display you want to adjust by using the Select button or by checking the checkbox.
2) Info Grid displays only the display having TV, AV, S-Video, Component, HDMI1, HDMI2 or DTV as input source.
3) Switch Image Size of the selected display randomly.
4) The screen modes can only be adjusted when a TV (PAL only) is connected and the Image Size item is set to Auto
Wide.
HDMI2 may not be supported depending on the product.
Custom may not be supported depending on the product.
Auto Wide, Zoom1 and Zoom2 are not available for selection when the input signal type for Component
and DVI (HDCP) is 720p or 1080i.
(The Auto Wide mode is available only for TV, AV, and S-Video.)
The Input source of MagicInfo works only on MagicInfo model.
The Input source of TV works only on TV model.
The Image Size Control feature is available only for the displays whose power status is ON.
Time
1. Click Time of the main icons and the Time Control screen appears.
Info Grid shows some basic information necessary to Time Control.
1) Set clock
- Set the current time for the selected display (PC Time).
- To change the current time, first change the PC Time.
2) Timer
- Sets up Timer1, Timer2, Timer3 and Holiday Management.
3) Shows whether Timer is activated.
The Input source of MagicInfo works only on MagicInfo model.
The Input source of TV works only on TV model.
Time Control is available only for the displays for which the power status is ON.
Time
Setting up Timer and Holiday Management
1. 1. Setting up Timer1, Timer2 and Timer3
1) On Time
- Sets the time in hours, in minutes and as AM/PM for turning the selected monitor on.
2) Off Time
- Sets the time in hours, in minutes and as AM/PM for turning the selected monitor off.
3) Volume
- Selects the volume when the selected monitor is turned on.
4) Source
- Selects the external input source that will be displayed when the selected monitor is turned on.
5) Holiday
- Applies the Holiday Management function to the Timer.
6) Repeat
- Available selections include Once, EveryDay, Mon~Fri, Mon~Sat, Sat~Sun, and Manual.
z
z
z
z
z
z
Once : The Timer goes off only once.
EveryDay : EveryDay: The Timer repeats daily.
Mon~Fri : The Timer repeats from Monday through Friday.
Mon~Sat : The Timer repeats from Monday through Saturday.
Sat~Sun : Sat~Sun: The Timer goes off on Saturday and Sunday.
Manual : Select a day of the week you want the Timer to go off.
2. Setting Holiday Management
The Holiday Management function specifies the dates in which the monitor will not be turned on or off by the Timer.
1) Specifies the date.
2) Delete All
- Deletes all of the holidays.
3) Add
- Adds the specified date.
4)
- Deletes the schedule in the selected line.
The Holiday Management function can be turned on or off in the Timer setup menu.
The Input source of MagicInfo works only on MagicInfo model.
The Input source of TV works only on TV model.
Time Control is available only for the displays for which the power status is ON.
Only enabled for a TV when Source is set to TV in On Time mode.
Only enabled for a model with MagicInfo installed when Source is set to MagicInfo in On Time mode.
PIP
PIP Size
1. Click PIP of the main icons and the PIP control screen appears.
Selects displays you want to adjust using the Select button or checkboxes.
Info Grid shows some basic information necessary to PIP Size Control.
1) PIP Size
- Shows the current PIP Size of the display in use.
2) OFF
- Turns off the PIP of the selected display.
3) Large
- Turns on the PIP of the selected display and changes the size to Large.
4) Small
- Turns on the PIP of the selected display and changes the size to Small.
5) Double 1
- Turns on the PIP of the selected display and changes the size to Double 1.
6) Double 2
- Turns on the PIP of the selected display and changes the size to Double 2.
7) Double 3 (Picture By Picture)
- Turns on the PBP of the selected display and changes the size to Double 3.
The Input source of MagicInfo works only on MagicInfo model.
The Input source of TV works only on TV model.
PIP Size can be controlled with turning on the LCD Display power.
PIP
PIP Source
1. Click PIP of the main icons and the PIP control screen appears.
Info Grid shows some basic information necessary to PIP Source Control.
1) PIP Source
- PIP Source can be controlled with turning on the LCD Display power.
2) PC
- Changes the source of the PIP of the selected display to PC.
3) BNC
- Changes the source of the PIP of the selected display to BNC.
4) DVI
- Changes the source of the PIP of the selected display to DVI.
5) TV
- Changes the source of the PIP of the selected display to TV.
6) DTV
- Changes the source of the PIP of the selected display to DTV.
7) AV
- Changes the source of the PIP of the selected display to AV.
8) S-Video
- Changes the source of the PIP of the selected display to S-Video.
9) Component
- Changes the source of the PIP of the selected display to Component.
10) HDMI1/HDMI2
- Changes the source of the PIP of the selected display to HDMI.
11) DP
- Switches the PIP Source of the selected Display to DP.
HDMI2 may not be supported depending on the product.
DP may not be supported depending on the product.
Some of the PIP Sources may not be available for selection, depending on the input source type of the
Main Screen.
The Input source of MagicInfo works only on MagicInfo model.
The PIP Control feature is available only for the displays whose power status is ON and the PIP
function is set to ON.
Settings
Picture
1. Click Settings of the main icons and the Settings Control screen appears.
Basic information required to adjust the Picture is displayed in the main menu. Settings for the selected monitor will
be displayed if one of the connected monitors is selected, and the default settings will be displayed if all monitors
are selected by clicking All and Select. If a value is changed in this screen, the current mode will automatically
switch to custom mode.
1) Picture
- Available only for TV, AV, S-Video, Component, HDMI1, HDMI2, DTV.
2) Contrast
- Adjusts Contrast of the selected display.
3) Brightness
- Adjusts Brightness of the selected display.
4) Sharpness
- Adjusts Sharpness of the selected display.
5) Color
- Adjusts Color of the selected display.
6) Tint
- Adjusts Tint of the selected display.
- Available only for NT.
7) Color Tone
- Adjusts the Color Tone for the selected display.
8) Color Temp
- Adjusts the Color Temp for the selected display.
9) Brightness Sensor
- Adjusts the Brightness Sensor for the selected display.
10) Dynamic Contrast
- Adjusts the Dynamic Contrast for the selected display.
HDMI2 may not be supported depending on the product.
Brightness Sensor may not be supported depending on the product.
The Input source of MagicInfo works only on MagicInfo model.
Color Temp is only enabled if the Color Tone is set to Off.
The Input source of TV works only on TV model.
This feature is available only for the displays whose power status is ON and if no selection is made, the
factory default is displayed.
Settings
Picture PC
1. Click Settings of the main icons and the Settings Control screen appears.
Basic information required to adjust settings is displayed. Settings for the corresponding SET will be imported and
displayed on the slider if a display ID is selected, and the default settings will be displayed if all display IDs are
selected by clicking All and Select. If a value is changed in this screen, the current mode will automatically switch to
custom mode.
1) Picture PC
- Available only for PC, BNC, DVI and DP.
2) Contrast
- Adjusts Contrast of the selected display.
3) Brightness
- Adjusts Brightness for the selected display.
4) Red
- Adjusts red Color of the selected display.
- Available only for NT.
5) Green
- Adjusts green Color of the selected display.
- Available only for NT.
6) Blue
- Adjusts blue Color of the selected display.
- Available only for NT.
7) Color Tone
- Adjusts the Color Tone for the selected display.
8) Color Temp
- Adjusts the Color Temp for the selected display.
9) Brightness Sensor
- Adjusts the Brightness Sensor for the selected display.
10) Dynamic Contrast
- Adjusts the Dynamic Contrast for the selected display.
DP may not be supported depending on the product.
Brightness Sensor may not be supported depending on the product.
The Input source of MagicInfo works only on MagicInfo model.
The Input source of TV works only on TV model.
Color Temp is only enabled if the Color Tone is set to Off.
This feature is available only for the displays whose power status is ON and if no selection is made, the
factory default is displayed.
Settings
Audio
1. Click Settings of the main icons and the Settings Control screen appears.
Basic information required to adjust Audio is displayed in the display window. Settings for the corresponding SET will
be imported and displayed on the slider if a display ID is selected, and the default settings will be displayed if all
display IDs are selected by clicking All and Select. If a value is changed in this screen, the current mode will
automatically switch to custom mode.
1) Audio
- Controls audio settings for all input sources.
2) Bass
- Adjusts Bass of the selected display.
3) Treble
- Adjusts Treble of the selected display.
4) Balance
- Adjusts Balance of the selected display.
5) SRS TS XT
- SRS TS XT Sound ON/OFF of the selected display.
6) Sound Select
- Select either Main or Sub when PIP is On.
The Input source of MagicInfo works only on MagicInfo model.
The Input source of TV works only on TV model.
This feature is available only for the displays whose power status is ON and if no selection is made, the
factory default is displayed.
Settings
Image Lock
1. Click Settings of the main icons and the Settings Control screen appears.
Info Grid shows some basic information necessary to Settings Control.
1) Image Lock
- Available only for PC, BNC.
2) Coarse
- Adjusts Coarse of the selected display.
3) Fine
- Adjusts Fine of the selected display.
4) Position
- Adjusts Position of the selected display.
5) Auto Adjustment
- Self-Adjust to the incoming PC signal.
The Input source of MagicInfo works only on MagicInfo model.
The Input source of TV works only on TV model.
Settings Control is available only for the displays for which the power status is ON.
Maintenance
Lamp Control
1. Click on the "Maintenance" icon in the Main Icon column to display the Maintenance screen.
An "Info Grid" showing several basic data items appears.
1) Maintenance
- Allows the Maintenance Control function for all input sources.
2) Lamp Control
- Automatically adjusts the backlight of the selected display at a specified time.
The Manual Lamp Control automatically turns off if you adjust using the Auto Lamp Control.
- Allows you to adjust the backlight of the selected display regardless of the time.
The Auto Lamp Control automatically turns off if you adjust using the Manual Lamp Control.
3) Ambient Light
- Detects the ambient light intensity at the designated monitor and automatically adjusts the picture brightness.
- You can specify a Reference value and designate a monitor that will automatically determine Lamp Value (the light
intensity from the lamp), based on the ambient light intensity.
Ambient Light is only supported for models that have a brightness sensor and is only enabled when
Ambient Brightness Mode is selected in the Lamp Control menu.
Auto Lamp Control and Manual Lamp Control are only enabled when User Control Mode is selected in
the Lamp Control menu.
The Maintenance Control feature is available only for the displays whose power status is ON.
The Input source of MagicInfo works only on MagicInfo model.
The Input source of TV works only on TV model.
Maintenance
Scroll
1. Click on the "Maintenance" icon in the Main Icon column to display the Maintenance screen.
1) Scroll
- This function is used to remove the afterimages that occur when a still screen is displayed on the selected
display
for a long time.
2) Pixel Shift
- This allows the screen to be moved finely at the specified time interval.
3) Safety Screen
- The Safety Screen function is used to prevent afterimages from occurring when a still screen is displayed on the
monitor for a long time. The Interval item is used to set the repetition cycle in hour units and the Time item is
used to set the time when the Safety Screen function must be performed.
The Type item can be set to Scroll, Pixel, Bar, Eraser, All White, or Pattern.
4) Safety Screen2
- This function is used to prevent afterimages from occurring. There are five (5) types that you can select and
control with this function.
For the Scroll type, the Time item can be set to 1, 2, 3, 4 or 5. For the Bar and Eraser types, it can be set
to 10, 20, 30, 40 or 50. For the All White and Pattern type, it can be set to 1, 5, 10, 20 or 30.
The Input source of MagicInfo works only on MagicInfo model.
The Input source of TV works only on TV model.
The Maintenance Control feature is available only for the displays whose power status is ON.
Maintenance
Video Wall
1. Click on the "Maintenance" icon in the Main Icon column to display the Maintenance screen.
1) Video Wall
- A Video Wall is a set of video screens that are connected together, so that each screen shows a part of the whole
picture or so that the same picture is repeated on each screen.
2) Video Wall Control
- Video Wall properties can be configured.
1) On / Off
- Turns on/off the Video Wall function of the selected display.
2) Format
- The format can be selected to see a divided screen.
z
Full
z
Natural
3) Video Wall (Screen divider)
- The screen can be divided into.
You can select a number of screens with a different layout when dividing.
z Select a mode from Screen divider.
z Select a display from Display Selection.
z The place will be set up by pressing a number in the selected mode.
z The maximum number of monitors that can be arranged: Horizontal X Vertical = 100
z Up to 15 monitors can be arranged in a row. The maximum value for Horizontal is 6 if Vertical is set to 15 while
the maximum value for Vertical is 6 if Horizontal is set to 15.
4) Viewing Screen Splits
- You can view and change the layout of screens using the Screen Divider settings.
The range of the Screen Divider setting may differ depending on the model.
You may not operate this function in MagicInfo.
The Input source of TV works only on TV model.
The Maintenance Control function is available only for the displays where the power status is ON.
Troubleshooting
1. The display you wish to control does not appear on the Power Control Info Grid
- Check the connection of RS232C. (Check if it is properly connected to the Com1 port)
- Check the displays to see if any of the other displays connected have the same ID. If more than one displays have
the same ID, those displays are not properly detected by the program due to data conflict.
- For monitors that support a Set ID between 0 to 99, you have to set the Set ID to a value between 0 and 99.
Note :
Check if the Set ID of the monitor is a value between 0 and 99 (set the value using the Display menu).
2. The display you wish to control does not appear on the other Control Info Grids
- Check to see if the display power is ON. (You can check this in Power Control Info Grid)
- Check if you can change the input source of the display.
3. The dialogue box appears repeatedly.
- Check to see if the display you wish to control is selected.
4. Both On Timer and Off Timer have been set but different time is showing.
- Apply current time to synchronize the display clocks.
5. The remote may not function properly when you turn off the remote Function, disconnect the RS-232C cable, or exit
the program in an Irregular manner. Rerun the program and turn the remote function again to Restore normal
functions.
<Note> This program may malfunction due to problems in communication circuits or interference from electronic
appliances nearby.
Settings Value Display In Multiple Display Mode
When there are more than one displays connected, the settings values are displayed as follows.
1. No selection: Displays the Factory Default Value.
2. Selected one display: Fetches and displays the settings value for the selected display.
3. Selected one display (ID1) and add another display (ID3): The program, which was displaying the settings value of
ID 1, fetches and displays the value of ID3.
4. If all sets are selected at the same time by clicking All and Select, the default value will be restored.
Adjusting the PDP Display
Input
Available Modes
•
PC / DVI / BNC
•
AV
•
HDMI
•
MagicInfo
•
Component
Note
•
MagicInfo can only be enabled when a network box is connected.
•
The HDMI port and network box cannot be connected at the same time.
Source List
MENU → ENTER →
→ ENTER →
→
,
→ ENTER
Use to select PC, DVI or other external input sources connected to the PDP Display. Use to
select the screen of your choice.
1.
PC
2.
DVI
3.
AV
4.
HDMI
5.
MagicInfo
6.
Component
7.
BNC
Note
•
The direct button on the remote control is the 'SOURCE' button.
Edit Name
MENU → ENTER →
→
→ ENTER →
39
→
,
→ ENTER
Adjusting the PDP Display
Name the input device connected to the input jacks to make your input source selection
easier.
VCR / DVD / Cable STB / HD STB / Satellite STB / AV Receiver / DVD Receiver / Game /
Camcorder / DVD Combo / DHR / PC
Note
•
When connecting a PC to the HDMI or DVI terminal, set Edit Name to PC.
•
In other cases, set Edit Name to AV.
•
However, since 640x480, 720P (1280x720), and 1080p (1920x1080) are common signals
for AV and PC, make sure to set the Edit Name in accordance with the input signal.
•
The Picture menu changes depending on the input signal and Edit Name.
Picture [PC / DVI / BNC / MagicInfo Mode]
Available Modes
•
PC / DVI / BNC
•
AV
•
HDMI
•
MagicInfo
•
Component
Note
•
MagicInfo can only be enabled when a network box is connected.
•
The HDMI port and network box cannot be connected at the same time.
MagicBright
MENU →
→ ENTER →
→ ENTER →
40
→
,
→ ENTER
Adjusting the PDP Display
MagicBright is a new feature providing the optimum viewing environment depending on the
contents of the image you are watching. Currently four different modes are available: Entertain, Internet, Text and Custom. Each mode has its own pre-configured brightness value. You
can easily select one of the four settings by simply pressing the MagicBright control button.
1.
Entertain
High brightness
For watching motion pictures such as a DVD or VCR.
2.
Internet
Medium brightness
For working with a mixture of images such as texts and graphics.
3.
Text
Normal brightness
For documentations or works involving heavy text.
4.
Custom
Although the values are carefully chosen by our engineers, the pre-configured values
may not be comfortable to your eyes depending on your taste.
If this is the case, adjust the brightness and contrast by using the OSD menu.
Custom
By using the on-screen menus, the contrast and brightness can be changed to your personal
preference.
MENU →
→ ENTER →
→ ENTER →
→
Note
By adjusting the picture using the Custom function, MagicBright will change to Custom mode.
Contrast
MENU → → ENTER →
→ , → ENTER
→
Adjusts the Contrast.
41
→ ENTER →
→ ENTER→
Adjusting the PDP Display
Brightness
MENU →
→ ENTER →
→ , → ENTER
→ ENTER →
→
→
→ ENTER→
→
→ ENTER →
Adjusts the Brightness.
Sharpness
MENU →
→ ENTER →
→ , → ENTER
→ ENTER →
→
→
Adjusts the Sharpness.
Color Tone
MENU →
→ ENTER →
→
→
→ENTER →
→
,
→ ENTER
The color tones can be changed.
1.
Off
2.
Cool
3.
Normal
4.
Warm
5.
Custom
Note
If you set the Color Tone to Cool, Normal, Warm, or Custom, the Color Temp function is
disabled.
If you set the Color Tone to Off, the Color Control function is disabled
Color Control
Adjusts individual Red, Green, Blue color balance.
MENU →
→ ENTER →
→
→
42
→ → ENTER →
Adjusting the PDP Display
Note
If you adjust the picture by using the Color Control function, Color Tone will turn to the Custom mode.
Red
MENU → → ENTER →
→
→ , → ENTER
→
→ → ENTER →
→
→ ENTER
Green
MENU →
ENTER→
→ ENTER →
→
→ , → ENTER
→
→ → ENTER →
→
→
→
→
Blue
MENU → → ENTER →
→
ENTER →
→ , → ENTER
→
→ → ENTER →
→
Color Temp.
MENU → → ENTER →
→ → → → ENTER →
→ , → ENTER
Color Temp. is a measure of the 'warmth' of the image colors.
Note
This function is only enabled if the Color Tone is set to Off.
Image Lock
Image Lock is used to fine-tune and get the best image by removing noise that creates unstable images with jitters and shakiness. If satisfactory results are not obtained using the Fine
adjustment, use the Coarse adjustment and then use Fine again.
Note
Available in PC mode only
MENU →
→ ENTER →
→
→
→ → → ENTER →
MENU →
→
→ ENTER →
→ , → ENTER
→
→
→ → → ENTER →
Coarse
43
→ ENTER
Adjusting the PDP Display
Removes noise such as vertical stripes. Coarse adjustment may move the screen image
area. You may relocate it to the center using the horizontal control menu.
Fine
MENU → → ENTER →
→
ENTER →
→ , → ENTER
→
→ → → ENTER →
→
→
Removes noise such as horizontal stripes. If the noise persists even after Fine tuning, repeat
it after adjusting the frequency (clock speed).
H-Position
MENU → → ENTER →
→ ENTER →
→ ,
→ → → → → ENTER →
→ ENTER
→
→
→
→
Adjusts the screen location horizontally.
V-Position
MENU → → ENTER →
→ → ENTER →
→ → → → → ENTER →
→ , → ENTER
Adjusts the screen location vertically.
Auto Adjustment
MENU →
→ ENTER →
→
→
→
→ → → ENTER →
The values of Fine, Coarse, Position are adjusted automatically. By changing the resolution
in the control panel, the auto function is performed.
Note
Available in PC mode only
Signal Balance
This is used to make up for the weak RGB signal transmitted by a long signal cable.
MENU →
→ ENTER →
→
→
→ ENTER →
→ ENTER →
→
→
→
→
→
→ ENTER →
→
→ →
→ ENTER
→
→ ENTER →
→
→
Signal Balance
MENU →
44
,
Adjusting the PDP Display
Selects either On or Off with the signal Balance.
Signal Control
MENU →
1.
→ ENTER →
→ → ENTER →
→ →
→ ENTER →
→
→
→ → →
→ ENTER →
→ ENTER →
→ , →
→ ENTER →
→ → ENTER →
→
→
→
→
→ → → → ENTER →
→ ENTER →
→ ,
→ ENTER →
→ → ENTER →
→ ENTER
→
→
→
→
→ → → → ENTER →
→ → ENTER →
→
→ ENTER →
→ → ENTER →
→ , → ENTER
→
→
→
→ ENTER →
→ → ENTER →
→ , → ENTER
→
G-Gain
→ ENTER
B-Gain
MENU →
,
R-Offset
MENU →
5.
→
→
MENU →
4.
→
→ ENTER →
→ → ENTER →
ENTER
3.
→
R-Gain
MENU →
2.
→
→
→
→ →
→
→
→ ENTER →
→ ENTER →
G-Offset
MENU →
45
→
→
→
→
→
→ → → ENTER →
→ → → ENTER →
Adjusting the PDP Display
6.
B-Offset
MENU →
→
→ ENTER →
→ → ENTER →
→ , → ENTER
→
→
→ → →
→ → →
→ ENTER →
→ → ENTER
→
→
→
→ → → → → ENTER →
Size
MENU → → ENTER →
→ ENTER
→
→
The Size can be switched.
1.
16:9
2.
4:3
Picture [ AV / HDMI / Component Mode]
Available Modes
•
PC / DVI / BNC
•
AV
•
HDMI
•
MagicInfo
•
Component
Note
•
MagicInfo can only be enabled when a network box is connected.
•
The HDMI port and network box cannot be connected at the same time.
Mode
MENU →
→ ENTER →
→ ENTER →
46
→
,
→ ENTER
→
,
Adjusting the PDP Display
The PDP Display has four automatic picture settings ("Dynamic", "Standard", "Movie" and
"Custom") that are preset at the factory.
Dynamic, Standard, Movie, or Custom can be activated.
1.
Dynamic
2.
Standard
3.
Movie
4.
Custom
Custom
By using the on-screen menus, the contrast and brightness can be changed to your personal
preference.
MENU →
→ ENTER →
→ ENTER →
→
Contrast
MENU → → ENTER →
→ , → ENTER
→ ENTER →
→
→ ENTER→
Adjusts the Contrast.
Brightness
MENU →
→ ENTER →
→ , → ENTER
→
→ ENTER →
→
→ ENTER→
Adjusts the Brightness.
Sharpness
MENU →
→ ENTER →
→ , → ENTER
→
Adjusts the picture Sharpness.
47
→ ENTER →
→
→
→ ENTER→
Adjusting the PDP Display
Color
MENU → → ENTER →
→
→ , → ENTER
→
→ ENTER →
→
→
→
→ ENTER
Adjusts the picture Color.
Tint
MENU → → ENTER →
→
→ , → ENTER
→ → ENTER →
→ → → → → ENTER
Adds a natural tone to the display.
Color Tone
MENU →
→ ENTER →
→
→
→ ENTER →
→
,
→ ENTER
The color tones can be changed. The individual Color components are also user adjustable.
1.
Off
2.
Cool2
3.
Cool1
4.
Normal
5.
Warm1
6.
Warm2
Note
If you set the Color Tone to Cool2, Cool1, Normal, Warm1, or Warm2, the Color Temp function
is disabled.
Color Temp.
MENU → → ENTER →
→ → → → ENTER →
Color temp. is a measure of the 'warmth' of the image colors.
48
→ , → ENTER
Adjusting the PDP Display
Note
This function is only enabled if the Color Tone is set to Off.
Size
MENU →
→ ENTER →
→
→
→
→ → ENTER →
→
,
→ ENTER
The Size can be switched.
1.
16:9 - Sets the picture to 16:9 wide mode.
2.
Zoom 1 - Magnifies the size of the picture on the screen.
3.
Zoom 2 - Magnifies the size of the picture more than “Zoom 1”.
4.
4:3 - Sets the picture to 4:3 normal mode.
5.
Just Scan - Displays the input scenes as they are without any cutoff when HDMI / Component 720p, 1080i, 1080p signals are input.
Note
Certain external devices may feed the display an out of spec signal that may cause cutoff
even when using the Just Scan feature.
ZOOM1, ZOOM2 will be unavailabel in HDMI / Component mode.
Note
The Position and Reset functions are available when Zoom1 or Zoom2 is run.
Digital NR (Digital Noise Reduction)
MENU → → ENTER →
→ ENTER
→
→
→
→ → → ENTER →
→
,
Turns the Digital Noise Reduction feature Off/On. The Digital Noise Reduction feature allows
you to enjoy clearer and crisper images.
Deactivated in HDMI / AV with a resolution of 1080p.
49
Adjusting the PDP Display
1.
Off
2.
On
Note
Digital NR function is not available for all resolutions.
Film Mode
MENU → → ENTER →
→ , → ENTER
→
→
→
→
→
→
→ ENTER →
The Film Mode feature offers you a theater-quality viewing experience.
Film Mode is supported in AV, Component (480i / 1080i) and HDMI (480i / 1080i).
(In HDMI mode, this function can be available when the input signal is interlaced scan; it
cannot be available with progressive scan signal.)
1.
Off
2.
On
Sound
Available Modes
•
PC / DVI / BNC
•
AV
•
HDMI
•
MagicInfo
•
Component
Note
•
MagicInfo can only be enabled when a network box is connected.
•
The HDMI port and network box cannot be connected at the same time.
Mode
MENU →
→ → ENTER →
→ ENTER →
50
→
,
→ ENTER
Adjusting the PDP Display
The PDP Display has a built-in high fidelity stereo amplifier.
1.
Standard
Selects Standard for the standard factory settings.
2.
Music
Selects Music when watching music videos or concerts.
3.
Movie
Selects Movie when viewing movies.
4.
Speech
Selects Speech when watching a show that is mostly dialogue (i.e., news).
5.
Custom
Selects Custom if you want to adjust the settings according to your personal preferences.
Custom
The sound settings can be adjusted to suit your personal preferences.
MENU →
→ → ENTER →
→ → ENTER →
Note
•
You can hear the sound even when sound value is set to 0.
•
If you adjust sound using Custom function, Mode will turn to Custom mode.
Bass
MENU → → → ENTER →
→ ENTER
→ → ENTER →
→ENTER→
→ → ENTER →
→ →ENTER→
Emphasizes low frequency audio.
Treble
MENU → → → ENTER →
→ , → ENTER
51
→ ,
Adjusting the PDP Display
Emphasizes high frequency audio.
Balance
MENU →
→ → ENTER →
→ , → ENTER
→ → ENTER →
→ → →ENTER→
Allows you to Adjusts the sound balance between the left and right speakers.
Auto Volume
MENU → → → ENTER →
→ → → ENTER →
→ , → ENTER
Reduces the difference in volume control between broadcasters.
1.
Off
2.
On
SRS TS XT
MENU → → → ENTER →
→ → → → ENTER →
→ , → ENTER
SRS TS XT is a patented SRS technology that solves the problem of playing 5.1 multichannel
content over two speakers. TruSurround delivers a compelling, virtual surround sound experience through any two-speaker playback system, including internal television speakers. It
is fully compatible with all multichannel formats.
1.
Off
2.
On
Setup
Available Modes
•
PC / DVI / BNC
52
Adjusting the PDP Display
•
AV
•
HDMI
•
MagicInfo
•
Component
Note
•
MagicInfo can only be enabled when a network box is connected.
•
The HDMI port and network box cannot be connected at the same time.
Language
MENU →
→ → → ENTER →
→ ENTER →
→
,
→ ENTER
You can choose one of 13 languages.
Note
The language chosen affects only the language of the OSD. It has no effect on any software
running on the computer.
Time
You can set the time.
MENU →
→ → → ENTER →
→
→ ENTER →
Clock Set
MENU →
→ → → ENTER →
→ , → , → ENTER
→
Current Time Setting.
53
→ ENTER →
→ ENTER→
Adjusting the PDP Display
Sleep Timer
MENU →
→ → → ENTER →
→ , → ENTER
→
→ ENTER →
→
→ ENTER→
Turns the PDP Display off automatically at certain times.
1.
Off
2.
30
3.
60
4.
90
5.
120
6.
150
7.
180
Timer1 / Timer2 / Timer3
MENU → → → → ENTER →
→ ENTER→ [Timer1 / Timer2 / Timer3]
→
,
/ ,
→
→ ENTER →
→ →
→ →
→
→ ENTER
You can set the PDP display to automatically turn on or off at a specified time.
Note
•
Only enabled when the clock is set using the Clock Set menu.
•
The Manual option allows you to select a day of the week.
Holiday Management
MENU → → → → ENTER →
[Holiday Management]
•
→
Add
54
→ ENTER →
→ →
→ ENTER→
Adjusting the PDP Display
MENU → → → → ENTER →
→ → ENTER →
→ ENTER → [Holiday Management]→ ENTER → [Add]
→ , / ,
→ → →
→ →
→ ENTER
You can register holidays.
•
Delete Selected
MENU → → → → ENTER →
→ → ENTER →
→ → → → →
→ ENTER → [Holiday Management]→ , → ENTER → → , → ENTER → [Delete
Selected]
→ ,
→ ENTER
You can delete selected holidays.
Note
•
•
Only enabled when registered holidays are selected.
•
More than one holiday can be selected and deleted.
Delete All
→ → ENTER →
→ → →
MENU → → → → ENTER →
→ ENTER → [Holiday Management]→ → → ENTER → [Delete All]
→ ,
→ ENTER
You can delete all the registered holidays.
55
→ →
Adjusting the PDP Display
Menu Transparency
MENU → → → → ENTER →
→ ENTER
→ →
→ ENTER →
→
,
Change the transparency of the background of the OSD.
1.
High
2.
Medium
3.
Low
4.
Opaque
Safety Lock
Change PIN
MENU → → → → ENTER →
→
→ → → → ENTER →
→ ENTER
→ [0∼9] → [0∼9] → [0∼9] → [0∼9]
The password can be changed.
Note
The preset password for the PDP Display is "0000".
Lock
MENU → → → → ENTER →
ENTER →
→ → →
→ [0∼9] → [0∼9] → [0∼9] → [0∼9]
56
→ ENTER →
→
→
Adjusting the PDP Display
This is the function that locks the OSD in order to keep the current settings or to prevent
others from adjusting the settings.
Energy Saving
MENU → → → → ENTER →
→ , → ENTER
→ → → →
→ ENTER →
This feature adjusts the power consumption of the unit in order to save energy.
1.
Off
2.
On
Note
If Energy Saving mode is Off, you can obtain the maximum display brightness.
HDMI Black Level
MENU →
→
→ → ENTER →
→ , → ENTER
→
→
→
→
→
→ ENTER →
When a DVD or set-top box is connected to your TV via HDMI, it may cause a degradation
in the screen quality, such as an increase in the black level, a low contrast, or discoloration,
etc., depending on the external device connected. In this case, adjust the screen quality of
your TV by configuring the HDMI black level.
1.
Normal
2.
Low
Video Wall
A Video Wall is a set of video screens connected together, so that each screen shows a part
of the whole picture or where the same picture is repeated on each screen.
When the Video Wall is on, you can adjust the Video Wall screen setting.
MENU →
→
→
→ ENTER →
→
57
→
→
→
→
→
→ ENTER →
Adjusting the PDP Display
Note
When Video Wall is running, the Auto Adjustment, Image Lock, and Size functions are not
available. Video Wall does not operate in MagicInfo mode.
Video Wall
MENU →
→
,
→ → → ENTER →
→ ENTER →
→
→
→
→
→
→ ENTER →
→
→
→ ENTER →
→
→
→ ENTER →
→
→ ENTER
Turns Off/On the Video Wall function of the selected display Off/On.
1.
Off
2.
On
Format
MENU →
→
,
→ → → ENTER →
→ → ENTER →
→
→
→
→
→ ENTER
The Format can be selected to see a divided screen.
1.
Full
Provides a full screen without any margins.
2.
Natural
Displays a natural image with the original aspect ratio intact.
Horizontal
MENU →
→ → → ENTER →
→ → → ENTER →
→
58
→
→
→
Adjusting the PDP Display
→
,
→ ENTER
Sets how many parts the screen should be divided horizontally.
Five adjustment levels: 1, 2, 3, 4, and 5.
Vertical
MENU → → → → ENTER →
→ → → → ENTER →
→
,
→ → → → → → → ENTER →
→ ENTER
Sets how many parts the screen should be divided vertically.
Five adjustment levels: 1, 2, 3, 4, and 5.
Screen Divider
MENU →
→ → → ENTER →
→
→ → → → → ENTER →
→
→
→
→
→
→ ENTER →
The screen can be divided into several images. A number of screens can be selected with a
different layout when dividing.
•
Select a mode in Screen Divider.
•
Select a display in Display Selection.
•
The selection will be set up by pressing a number in the selected mode.
59
Adjusting the PDP Display
Safety Screen
The Safety Screen function is used to prevent afterimages that may appear when a still picture
is displayed on the screen over a long time.
•
The Safety Screen function scrolls the screen for the specified period of time.
•
This function is not available when the power is turned off.
MENU →
→ → → ENTER →
→ → → →
→
→
→ → → ENTER →
→ ENTER →
→ → → →
→ ENTER →
→
→
→ ENTER →
→
Pixel Shift
Pixel Shift
MENU →
→
→
,
→ ENTER →
→ ENTER
To prevent after-images on the screen you can use this function, so that every minute pixels
on the PDP are moved in horizontal or vertical direction.
1.
Off
2.
On
Horizontal Dot
MENU →
ENTER
→ → → ENTER →
→ ENTER →
→
→
→ ENTER →
→ , →
→ → → → → →
→ → → ENTER →
→
→ ENTER →
→ , →
→ → → → →
→ → ENTER →
Sets how many pixels the screen moves horizontally.
Five adjustment levels: 0, 1, 2, 3, and 4.
Vertical Line
MENU →
ENTER
→ → → ENTER →
→ ENTER →
60
Adjusting the PDP Display
Sets how many pixels the screen moves vertically.
Five adjustment levels: 0, 1, 2, 3, and 4.
Time
MENU →
ENTER
→ → → ENTER →
→ ENTER →
→ → → → → → →
→ → → → ENTER →
→ ENTER →
→ , →
Set the time interval for performing the horizontal or vertical movement, respectively.
Timer
Timer
MENU →
→ → → ENTER →
→ → ENTER →
→ → → →
→ ENTER →
→
→
→
,
→ → ENTER →
→ ENTER
You can set the timer for Screen Burn Protection.
If you start the operation to erase any residual image, the operation will be performed for the
set period of time and then automatically finish.
1.
Off
2.
On
Mode
MENU →
→ → → ENTER →
→ → ENTER →
→ → → → →
→ → ENTER →
61
→
→
→
,
→ ENTER →
→ ENTER
Adjusting the PDP Display
You can change the Safety Screen Type.
1.
Scroll
2.
Bar
3.
Eraser
4.
All White
5.
Pattern
Period
MENU →
→ → → ENTER →
→ → ENTER →
→ → → → →
→ → → ENTER →
→
→ → ENTER →
→ , → ENTER
Use this function to set the execution period for each mode set in the timer.
Time
MENU →
ENTER
→ → → ENTER →
→ → ENTER →
→ → → → → → →
→ → → → ENTER →
Within the set period of time specify a time for execution.
•
Mode-Scroll : 1~5 sec
•
Mode-Bar, Eraser : 10~50 sec
62
→ ENTER →
→ , →
Adjusting the PDP Display
•
Mode-All White, Pattern : 1, 5, 10, 20 30 min
Scroll
MENU →
→ → → ENTER →
→ → → ENTER →
→ → → →
→
→
→
→ ENTER →
This function prevents after-images on the screen by moving all the pixels on the PDP according to a pattern.
Use this function when there are remaining after-images or symbols on the screen, especially
when you displayed a still image on the screen for a long time.
Bar
MENU →
→ → → ENTER →
→ → → →
→ → → →ENTER →
→
→
→
→ ENTER →
This function prevents after-images on the screen by moving long black and white vertical
lines.
Eraser
MENU →
→ → → ENTER →
→ → → →
→ → → → →ENTER →
→
→
→
→ ENTER →
This function prevents after-images on the screen by moving a rectangular pattern.
All White
MENU →
→ → → ENTER →
→ → → → →
→ → → →
→ENTER →
63
→
→
→
→ ENTER →
Adjusting the PDP Display
This function prevents after-images on the screen by changing the color of pixels to white.
Use this function when there are remaining after-images or symbols on the screen, especially
when you displayed a still image on the screen for a long time.
Pattern
MENU →
→ → → ENTER →
→ → → → →
→
→ → → →
→ENTER →
→
→
→
→ ENTER →
This function prevents after-images on the screen by moving a diagonal pattern stored in the
panel repeatedly.
Resolution Select
MENU →
→
→ → → ENTER →
→ , → ENTER
→ → → →
→
→
→
→
→ENTER
When the picture is not displayed properly on the screen when setting the graphics card
resolution of the computer to 1024 x 768 @ 60Hz, 1280 x 768 @ 60Hz, 1360 x 768@ 60Hz
or 1366 x 768 @ 60Hz, by using this function(Resolution Select), you can have the picture
displayed on the screen in the specified resolution.
Note
Available in PC or BNC mode only
1.
Off
2.
1024 x 768
64
Adjusting the PDP Display
3.
1280 x 768
4.
1360 x 768
5.
1366 x 768
Note
Selecting the menu is only allowed when the graphics resolution is set to 1024 x 768 @ 60Hz,
1280 x 768 @ 60Hz, 1360 x 768 @ 60Hz or 1366 x 768 @ 60Hz.
Power On Adjustment
MENU →
→
→ → → ENTER →
→ → → →
→ , → ENTER
→
→
→
→
→ → ENTER
Adjusts the Power On time for the screen.
Caution: Set the Power On time to be longer to avoid overvoltage.
Side Gray
MENU → → → → ENTER →
ENTER →
→ , → ENTER
→ → → →
→
→
→
→
→ → →
Select the brightness of the grey for the screen background.
1.
Off
2.
Light
3.
Dark
Reset
Reverts the product settings to factory defaults. The Reset function is only available when
PC / DVI is being used.
65
Adjusting the PDP Display
MENU → → → → ENTER →
→ ENTER →
→ → → →
→
→
→
→
→ → →
→ → → → → → →
→ , → ENTER
→
→ → →
→
→ → →
Image Reset
MENU → → → → ENTER →
→ ENTER →
→ ENTER →
Note
Available in PC mode only
The Reset function is not available when Video Wall is On.
Color Reset
MENU → → → → ENTER →
→ ENTER →
→ → ENTER →
→ → → → → → →
→ , → ENTER
OSD Rotation
MENU →
→
→
→ ,
→
→
→
→ ENTER →
→
→ ENTER →
→ ENTER
OSD Rotate
1.
Landscape
2.
Portrait
Multi Control
Available Modes
•
PC / DVI / BNC
•
AV
•
HDMI
•
MagicInfo
66
→
→
→
→
→
→
→
→
→
Adjusting the PDP Display
•
Component
Note
•
MagicInfo can only be enabled when a network box is connected.
•
The HDMI port and network box cannot be connected at the same time.
Multi Control
Assigns an individual ID to the SET.
MENU →
•
→ → →
→ ENTER →
→ ENTER →
,
→ [0~9]
ID Setup
Assigns distinctive IDs to the SET.
•
ID Input
Use to select the transmitter functions of the individual SET. Only a SET where the ID
corresponds to the transmitter setting becomes activated.
MagicInfo
Available Modes
•
PC / DVI / BNC
•
AV
•
HDMI
•
MagicInfo
•
Component
Note
•
MagicInfo can only be enabled when a network box is connected.
•
The HDMI port and network box cannot be connected at the same time.
Note
•
The remote control can be used to select MagicInfo. However, it is recommended to use
a separate USB keyboard to utilize MagicInfo fully.
67
Adjusting the PDP Display
•
For MagicInfo in Device mode, moving external devices while booting may cause errors.
Set up external devices only if the PDP Display turns on.
•
Do not unplug the LAN cable used for the network (ex: video display). Otherwise, the
program (MagicInfo) may stop. If you do unplug the cable, restart the system.
•
Do not unplug the LAN cable used by an USB device (ex: video display). Otherwise, the
program (MagicInfo) may stop.
•
To access other sources, press the SOURCE button in MagicInfo.
•
The preset password for the PDP Display is "000000".
•
The server program's Power-On option works only if the PDP Display's power is completely shut off.
Please make sure not to use the Power-On option when the PDP Display is in the process
of shutting down since this may cause system errors on the PDP Display.
•
When using MagicInfo with the MagicInfo Server Program: perform Network mode.
•
When using MagicInfo with the device directly connected to PDP Display : execute Device
mode.
•
Press ESC to directly go to the MagicInfo Window screen.
•
To setup MagicInfo on a Windows screen, a keyboard and mouse are required.
•
To setup MagicInfo on a Windows screen, refer to the MagicInfo Server Help.
It is highly recommended not to turn off the AC power during an operation.
•
For pivoted PDP Displays, ticker transparency is not supported.
•
For pivoted PDP Displays, a screen resolution of up to 720*480(SD) is supported for
movies.
•
For drive D:, EWF is not applied.
•
To save Setup contents that have been changed when EWF is in the Enable state, you
must Commit them.
•
By selecting Disable, Enable or Commit, the system is restarted.
MagicInfo
1. Select Application - step 1
68
Adjusting the PDP Display
You can select an Application to be executed in your computer when Windows starts.
2. Select TCP/IP - step 2
In step 2 of MagicInfo Setup Wizard, you don’t have to go to Network Setting on the desktop
to make your settings for TCP/IP. You just do that at step 2 of MagicInfo installation.
3. Select Language - step 3
69
Adjusting the PDP Display
When using multiple languages, you can choose and set a specific language among them.
4. Select Screen Type - step 4
You can select which rotation type will be applied to your device.
5. Setup Information
70
Adjusting the PDP Display
Shows the settings that have been selected by the user.
Note
If the MagicInfo icon is not displayed on the notification area, double click the MagicInfo icon
on the window desktop. The icon will appear.
71
Troubleshooting
Self-Test Feature Check
Note
Check the following items yourself before calling for assistance. Contact a Service Center for
problems that you cannot solve by yourself.
Self-Test Feature Check
1.
Turn off both your computer and the PDP Display.
2.
Unplug the video cable from the back of the computer.
3.
Turn on the PDP Display.
The figure shown below ("Check Signal Cable") appears on a black background when
the PDP Display is working normally even though no video signal is detected: While in
the Self-Test mode, the LED power indicator remains green and the figure moves around
on the screen.
4.
Turn off your PDP Display and reconnect the video cable; then turn on both your computer and the PDP Display
If your PDP Display screen remains blank after using the previous procedure, check your
video controller and computer system; your PDP Display is functioning properly.
Warning Messages
You can even view the screen at a resolution of 1920 x 1080. However, you will receive the
following message for a minute; You can choose to change the screen resolution or stay in
the current mode during that time. And if the resolution is more than 85Hz, you will see the
black screen because the PDP Display does not support over 85Hz.
Note
Refer to Specifications > Preset Timing Modes for the resolutions or frequencies supported
by the PDP Display.
Maintenance and Cleaning
1) Maintaining the PDP Display Case.
Clean with a soft cloth after disconnecting the power cord.
72
Troubleshooting
•
Do not use benzene, thinner or other flammable substances, or a wet cloth.
2) Maintaining the Flat Panel Display Screen.
Clean with a soft cloth (cotton flannel) smoothly.
•
Never use acetone, benzene or thinner.
(They may cause flaws or deformation of the screen
surface.)
•
The user will be required to pay costs and related
expenses for repairing damages caused.
Symptoms and Recommended Actions
Note
A PDP Display recreates visual signals received from the computer. Therefore, if there is a
problem with the computer or the video card, this can cause the PDP Display to become
blank, have poor coloring, become noisy, and video mode not supported, etc. In this case,
first check the source of the problem, and then contact a Service Center or your dealer.
1.
Check if the power cord and the video cables are properly connected to the computer.
2.
Check if the computer beeps more than 3 times when booting.
(If it does, request an a service for the main board of the computer.)
3.
If you installed a new video card or if you assembled the PC, check if you installed the
Adaptor(video).
4.
Check if the scanning ratio of the video screen is set to between 50 Hz ~ 85 Hz.
(Do not exceed 60Hz when using the maximum resolution.)
5.
If you have problems in installing the Adaptor (video) driver, boot the computer in Safe
Mode, remove the Display Adaptor in the "Control Panel −> System −> Device Administrator" and then reboot the computer to reinstall the Adaptor (video) driver.
Check List
Note
•
The following table lists possible problems and their solutions. Before calling for assistance, check the information in this section to see if you can remedy any problems for
yourself. If you do need assistance, please call the phone number on the Information
section or contact your dealer.
Problems related to the Installation (PC Mode)
Note
Problems related to the PDP Display installation and their solutions are listed.
Q:
The PDP Display screen flickers.
73
Troubleshooting
A:
Check if the signal cable between the computer and the PDP Display is securely connected.
(Refer to Connecting a Computer)
Problems related to the Screen
Note
Problems related to the PDP Display screen and their solutions are listed.
Q:
The screen is blank and the power indicator is off.
A:
Ensure that the power cord is firmly connected and the PDP Display is on.
(Refer to the Connecting a Computer)
Q:
"Check Signal Cable" message.
A:
Ensure that the signal cable is firmly connected to the PC or video sources.
(Refer to the Connecting a Computer)
A:
Ensure that the PC or video sources are turned on.
Q:
"Not Optimum Mode" message.
A:
Check the maximum resolution and the frequency of the video Adaptor.
A:
Compare these values with the data in the Preset Timing Modes Chart.
Q:
The picture rolls vertically.
A:
Check if the signal cable is securely connected. Re-connect it, if necessary.
(Refer to Connecting a Computer)
Q:
The image is not clear; picture is blurred.
A:
Run Frequency Coarse and Fine tuning.
A:
Turn on again after removing all accessories (video extension cable, etc.)
A:
Set the resolution and frequency to the recommended ranges.
Q:
The picture image is unstable and shakes.
A:
Check if the resolution and frequency set for the computer video card falls in the range
supported by the PDP Display. If not, reset them referring to the current Information
under the PDP Display menu and Preset Timing Modes.
Q:
Ghost images are shown in the picture.
A:
Check if the resolution and frequency set for the computer video card falls in the range
supported by the PDP Display. If not, reset them referring to the current Information
under the PDP Display menu and Preset Timing Modes.
Q:
The image is too light or too dark.
A:
Adjusts the brightness and contrast.
(Refer to the Brightness, Contrast)
74
Troubleshooting
Q:
The screen color is inconsistent.
A:
Adjust color using Custom under OSD Color Adjustment menu.
Q:
The color image is distorted by dark shadows.
A:
Adjust color using Custom under OSD Color Adjustment menu.
Q:
The color white is poor.
A:
Adjust color using Custom under OSD Color Adjustment menu.
Q:
The Power Indicator blinks.
A:
The PDP Display is currently saving the changes made to the settings to the OSD
memory.
Q:
The screen is blank and the power indicator light blinks every 0.5 or 1 seconds. The
PDP Display is using its power management system. Press any key on the keyboard.
A:
The PDP Display is using its power management system. Press a key on the keyboard.
Q:
The screen is blank and it is blinking.
A:
If you see the "TEST GOOD" message on the screen when you pressing the MENU
button, check the cable connection between the PDP Display and the computer to ensure that the connector is properly connected.
Problems related to Audio
Note
Problems related to audio signals and their solutions are listed below.
Q:
No sound.
A:
Ensure that the audio cable is firmly connected to both the audio-in port on your PDP
Display and the audio-out port on your sound card.
(Refer to the Connecting a Computer)
A:
Check the volume level.
Q:
The sound level is too low.
A:
Check the volume level.
A:
If the volume is still too low after turning the control to its maximum, check the volume
control on the computer sound card or software program.
Q:
The sound is too high or too low.
A:
Adjusts the Treble and Bass to the appropriate levels.
Problems related to the Remote Control
Note
Problems related to the remote control and their solutions are listed.
Q:
The remote control buttons do not respond.
A:
Check the polarities (+/-) of the batteries.
75
Troubleshooting
A:
Check if the batteries are empty.
A:
Check if the power is on.
A:
Check if the power cord is securely connected.
A:
Check if a special fluorescent or neon lamp is on in the vicinity.
Q:
How can I change the frequency?
A:
The frequency can be changed by reconfiguring the video card.
Q&A
Note
That video card support can vary, depending on the version of the driver used. (Refer
to the computer or the video card manual for details.)
Q:
How can I Adjusts the resolution?
A:
Windows XP:
Set the resolution in the Control Panel → Appearance and Themes → Display → Settings.
A:
Windows ME/2000:
Set the resolution in the Control Panel → Display → Settings.
* Contact the video card manufacturer for details.
Q:
How can I set the Power Saving function?
A:
Windows XP:
Configure it by selecting Control Panel → Appearance and Themes → Display →Screen
Saver Setting or configure it in the BIOS Setup of the computer. (Refer to the Windows /
Computer Manual).
A:
Windows ME/2000:
Configure it by selecting Control Panel → Display → Screen Saver Setting or Configure
it in the BIOS Setup of the computer. (Refer to the Windows / Computer Manual).
Q:
How can I clean the outer case/PDP Panel?
A:
Disconnect the power cord and then clean the PDP Display with a soft cloth, using either
a cleaning solution or plain water.
Do not leave any detergent or scratches on the case. Do not let any water enter the
PDP Display.
Q:
How can I play the video?
A:
The video supports the MPEG1 and WMV codecs only. Install the corresponding codec
to play the video. Note that some of the codecs can be incompatible.
76
Troubleshooting
Note
Before calling for assistance, check the information in this section to see if you can remedy
any problems yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer.
77
Specifications
General
General
SyncMaster P50HP, P50HP-2
Model Name
SyncMaster P63FP, P63FP-2
PDP Panel
Size
Display area
Pixel Pitch
SyncMaster
P50HP,
P50HP-2
50 " Diagonal (126 cm)
SyncMaster
P63FP,
P63FP-2
63 " Diagonal (160 cm)
SyncMaster
P50HP,
P50HP-2
1105.65 mm (H) X 622.08 mm (V)
SyncMaster
P63FP,
P63FP-2
1393.92 mm (H) X 784.08 mm (V)
SyncMaster
P50HP,
P50HP-2
0.81 mm (H) X 0.81 mm (V)
SyncMaster
P63FP,
P63FP-2
0.726 mm (H) x 0.726 mm (V)
Synchronization
Horizontal
30 ~ 81 kHz
Vertical
56 ~ 75 Hz
Display Color
16.77 M
Resolution
Optimum resolu- P50HP,
tion
P50HP-2
1360 x 768 @ 60 Hz depends on graphics card
used
P63FP,
P63FP-2
1920 x 1080 @ 60 Hz
Maximum resolu- P50HP,
tion
P50HP-2
1920 x 1080 @ 60 Hz
P63FP,
P63FP-2
1920 x 1080 @ 60 Hz
Maximum Pixel Clock
SyncMaster
P50HP, P50HP-2
165MHz (Analog,Digital)
78
Specifications
Maximum Pixel Clock
SyncMaster
P63FP, P63FP-2
165MHz (Analog,Digital)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal connectors
DVI-D In/Out(Can connect up to 10 PDP display units.),
D-sub, AV(Composite, CVBS), HDMI, RS232C In/Out
PC Audio In, Audio In(Stereo), Audio Out(Stereo)
Dimensions (W x H x D) / Weight
SyncMaster
P50HP, P50HP-2
1204.6 x 724.1 x 97.1 mm / 47.4 x 28.5 x 3.8 inch / 32.0 kg /
70.6 lbs
SyncMaster
P63FP, P63FP-2
1503.5 x 894.0 x 99.4 mm / 59.2 x 35.2 x 3.9 inch / 52.0 kg /
114.6 lbs
VESA Mounting Interface
SyncMaster
P50HP, P50HP-2
600 x 400
SyncMaster
P63FP, P63FP-2
676 x 407
Environmental considerations
Operating
Temperature : 32°F ~ 104°F (0°C ~ 40°C)
Humidity : 20 % ~ 80 %, non-condensing
Storage
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Humidity : 5 % ~ 95 %, non-condensing
Plug and Play Capability
This PDP Display can be installed on any Plug & Play compatible system. The
interaction of the PDP Display and the computer systems will provide the best operating conditions and PDP Display settings. In most cases, the PDP Display
installation will proceed automatically, unless the user wishes to select alternate
settings.
Dot Acceptable
PDP panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above are used for this product. But the pixels of
RED, GREEN, BLUE and WHITE color appear to be bright sometimes or some
black pixels may be seen. This is not from bad quality and you can use it without
any problems.
For example, the number of PDP sub pixels contained in this product are 2,133,440
(P50HP, P50HP-2).
For example, the number of PDP sub pixels contained in this product are 6,220,800
(P63FP, P63FP-2).
79
Specifications
Note
Design and specifications are subject to change without prior notice.
Class B (Information Communication equipment for residential use)
This device is registered for EMC requirements for home use (Class B). It can be used in all
areas.
(Class B equipment emits less electromagnetic waves than Class A equipment.)
PowerSaver
This PDP Display has a built-in power management system called PowerSaver. This system
saves by switching your PDP Display to low-power mode when it has not been used for a
certain amount of time. The PDP Display automatically returns to normal operation when you
press a key on the keyboard. For energy conservation, turn your PDP Display OFF when it
is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in your computer. Use the software
utility installed on your computer to set up this feature.
PowerSaver
State
Normal Opera- Power saving Power off
tion
mode
Power Indicator
Power MD230
Consumption
On
Blinking
Off
P50HP,
P50HP-2
The power
consumption
may differ depending on the
region. Refer
to the label on
the back of the
product.
2 watts
0 watt
P63FP,
P63FP-2
The power
consumption
may differ depending on the
region. Refer
to the label on
the back of the
product.
2 watts
0 watt
(Typical)
Note
•
The actual power consumption may be different from the indicated power consumption if
the system condition or settings are changed.
•
To stop any power consumption, disconnect the power cable on the back. Be sure to
disconnect the power if you intend to stay away from home for many hours.
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes,
the screen will be adjusted automatically. However, if the signal differs, the screen may go
blank while the power LED is on. Refer to the video card manual and adjusts the screen as
follows.
80
Specifications
Display Mode
Horizontal
Frequency
(kHz)
Vertical Fre- Pixel Clock
quency (Hz)
(MHz)
Sync Polarity
(H/V)
IBM, 640 x 350
31.469
70.086
25.175
+/-
IBM, 640 x 480
31.469
59.940
25.175
-/-
IBM, 720 x 400
31.469
70.087
28.322
-/+
MAC, 640 x 480
35.000
66.667
30.240
-/-
MAC, 832 x 624
49.726
74.551
57.284
-/-
MAC, 1152 x 870
68.681
75.062
100.000
-/-
VESA, 640 x 480
37.861
72.809
31.500
-/-
VESA, 640 x 480
37.500
75.000
31.500
-/-
VESA, 800 x 600
35.156
56.250
36.000
+/+
VESA, 800 x 600
37.879
60.317
40.000
+/+
VESA, 800 x 600
48.077
72.188
50.000
+/+
VESA, 800 x 600
46.875
75.000
49.500
+/+
VESA, 1024 x 768
48.363
60.004
65.000
-/-
VESA, 1024 x 768
56.476
70.069
75.000
-/-
VESA, 1024 x 768
60.023
75.029
78.750
+/+
VESA, 1152 x 864
67.500
75.000
108.000
+/+
VESA, 1280 x 960
60.000
60.000
108.000
+/+
VESA, 1280 x 1024
63.981
60.020
108.000
+/+
VESA, 1280 x 1024
79.976
75.025
135.000
+/+
VESA, 1360 x 768
(P50HP, P50HP-2)
47.712
60.015
85.500
+/+
VESA, 1920 x 1080
(P63FP, P63FP-2)
66.587
59.934
138.500
+/-
Horizontal Frequency
The time to scan one line connecting the right edge
to the left edge of the screen horizontally is called the
Horizontal Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency.
Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the
same image many times per second to display an
image to the user. The frequency of this repetition is
called the Vertical Frequency or Refresh Rate. Unit:
Hz
81
Information
For Better Display
Adjust the computer resolution and screen injection rate (refresh rate) on the
computer as described below to enjoy the best picture quality. You can have an
uneven picture quality on screen if the best picture quality is not provided for PDP.
•
Resolution: 1360 x 768(P50HP, P50HP-2)
Resolution: 1920 x 1080(P63FP, P63FP-2)
•
Vertical frequency (refresh rate): 60 Hz
PDP panels manufactured by using advanced semiconductor technology with
a precision of 1ppm (one millionth) and above is used for this product. But the pixels
of RED, GREEN, BLUE and WHITE color seem to be bright sometimes or some
of black pixels could be seen. This is not from bad quality and you can use it without
any problems.
•
For example, the number of PDP sub pixels contained in this product are
3,113,440.(P50HP, P50HP-2)
•
For example, the number of PDP sub pixels contained in this product are
6,220,800.(P63FP, P63FP-2)
When cleaning the monitor and the panel outside, please apply the recommended small amount of cleaner by using a soft cloth to polish. Do not force the
PDP area but rub softly. If excessive force is applied, you may stain it.
If you are not satisfied with the picture quality, you can get better quality of
picture by performing the "Auto Adjustment function" in display screen that is appeared as window termination button is pressed. If there's still noise after the
automatic adjustment, use the Fine/Coarse adjustment function.
When viewing a fixed screen for an extended period of time, a residual image
or blurriness may appear. Change the mode to energy save or set a screensaver
to move the picture when you need to be away from the monitor for an extended
period of time.
PRODUCT INFORMATION (Image Retention Free)
What is Image Retention ?
Image retention may not occur when a PDP panel is operated under normal conditions.
Normal conditions are defined as continuously changing video patterns. When the
PDP panel is operated for a long time with a fixed pattern .
Phosphor degradation may occur and the brightness is decreased. To prevent this,
the video pattern should be changed from time to time.
When viewing a still screen for a long time, the brightness of any part which was
bright in the previous fixed pattern becomes lower than that of its surroundings.
82
Information
Power Off, Screen Saver, or Power Save Mode
•
Turn the power off for 4 hours after 20 hours in use
•
Turn the power off for 2 hours after 12 hours in use
•
Set the Monitor to power off with the PC Display Properties Power Scheme.
•
Use a Screen saver if possible - Screen saver in one color or a moving image
is recommended.
Change the Color Information periodically
Note
Use Two different colors
Rotate the Color Information with 2 different colors every 30 minutes.
•
Avoid using a combination of characters and background color with large difference in luminance.
Avoid using Grey colors, which can cause Image retention easily.
Avoid: Colors with big difference in luminance (Black & White, Grey)
Change the characters color periodically
83
Information
•
Use Bright colors with little difference in luminance.
- Cycle : Change the characters color and background color every 30 minutes
•
Every 30 minutes, change the characters with movement.
•
All area display Moving image together with Logo periodically.
- Cycle: Display moving image together with Logo for 60 seconds after 4 hours
in use.
•
The best way to protect your monitor from Image retention is to turn Power off,
or set your PC, or System to operate a Screen Saver program when you are
not using it. Also Warranty service will be limited based on instruction guide.
Apply the Screen Scroll function on Product
•
Apply the Screen Scroll function
- Symptom: Horizontal Bar with Black Color move up and down.
Note
( Please check CD's User Guide at "OSD Function", some model's will not available )
Apply the Screen Pixel function on Product
•
Apply the Screen Pixel function
- Symptom: Dot with Black Color move up and down.
•
Apply the Screen Bar function
- Symptom: Horizontal / Vertical Bar with Black Color move up and down.
84
Information
Note
( Please check CD's User Guide at "OSD Function", some model's will not available. )
Apply the Screen Erasing function on Product
•
Apply the Screen Erasing function
- Symptom: 2 Vertical blocks move with erasing the display
Note
( Please check CD's User Guide at "OSD Function", some model's will not available )
85
Appendix
Contact SAMSUNG WORLDWIDE
Note
If you have any questions or comments relating to Samsung products, please contact the
SAMSUNG customer care center.
North America
U.S.A
1-800-SAMSUNG(726-7864) http://www.samsung.com
CANADA
1-800-SAMSUNG(726-7864) http://www.samsung.com
MEXICO
01-800-SAMSUNG
(726-7864)
http://www.samsung.com
Latin America
ARGENTINA
0800-333-3733
http://www.samsung.com
BRAZIL
0800-124-421
http://www.samsung.com
4004-0000
CHILE
800-SAMSUNG(726-7864)
http://www.samsung.com
COLOMBIA
01-8000112112
http://www.samsung.com
COSTA RICA
0-800-507-7267
http://www.samsung.com
ECUADOR
1-800-10-7267
http://www.samsung.com
EL SALVADOR
800-6225
http://www.samsung.com
GUATEMALA
1-800-299-0013
http://www.samsung.com
HONDURAS
800-7919267
http://www.samsung.com
JAMAICA
1-800-234-7267
http://www.samsung.com
NICARAGUA
00-1800-5077267
http://www.samsung.com
PANAMA
800-7267
http://www.samsung.com
PUERTO RICO
1-800-682-3180
http://www.samsung.com
REP. DOMINICA
1-800-751-2676
http://www.samsung.com
TRINIDAD & TO- 1-800-SAMSUNG(726-7864) http://www.samsung.com
BAGO
VENEZUELA
0-800-100-5303
http://www.samsung.com
Europe
AUSTRIA
0810 - SAMSUNG (7267864, http://www.samsung.com
€ 0.07/min)
BELGIUM
02-201-24-18
http://www.samsung.com/be
(Dutch)
http://www.samsung.com/
be_fr (French)
CZECH
800
(800-726786)
DENMARK
70 70 19 70
SAMSUNG http://www.samsung.com
http://www.samsung.com
86
Appendix
Europe
EIRE
0818 717100
http://www.samsung.com
ESTONIA
800-7267
http://www.samsung.com
FINLAND
030 - 6227 515
http://www.samsung.com
FRANCE
01 48 63 00 00
http://www.samsung.com
GERMANY
01805
SAMSUNG http://www.samsung.com
(726-7864, € 0,14/Min)
HUNGARY
06-80-SAMSUNG (726-7864) http://www.samsung.com
ITALIA
800-SAMSUNG (726-7864)
http://www.samsung.com
LATVIA
8000-7267
http://www.samsung.com
LITHUANIA
8-800-77777
http://www.samsung.com
LUXEMBURG
261 03 710
http://www.samsung.com
NETHERLANDS
0900-SAMSUNG
http://www.samsung.com
(0900-7267864) ( € 0,10/Min)
NORWAY
815-56 480
http://www.samsung.com
POLAND
0 801 1SAMSUNG(172678)
http://www.samsung.com
022-607-93-33
PORTUGAL
80820
(7267864)
SAMSUNG http://www.samsung.com
SLOVAKIA
0800 - SAMSUNG(726-7864) http://www.samsung.com
SPAIN
902 - 1 - SAMSUNG (902 172 http://www.samsung.com
678)
SWEDEN
0771 726 7864 (SAMSUNG) http://www.samsung.com
SWITZERLAND
0848 - SAMSUNG (7267864, http://www.samsung.com/ch
CHF 0.08/min)
http://www.samsung.com/
ch_fr/(French)
U.K
0845 SAMSUNG (7267864)
http://www.samsung.com
CIS
ARMENIA
0-800-05-555
AZERBAIJAN
088-55-55-555
BELARUS
810-800-500-55-500
GEORGIA
8-800-555-555
KAZAKHSTAN
8-10-800-500-55-500
KYRGYZSTAN
00-800-500-55-500
MOLDOVA
00-800-500-55-500
RUSSIA
8-800-555-55-55
http://www.samsung.com
TADJIKISTAN
8-10-800-500-55-500
http://www.samsung.com
UKRAINE
0-800-502-000
http://www.samsung.com/ua
http://www.samsung.com
http://www.samsung.com/
ua_ru
UZBEKISTAN
8-10-800-500-55-500
87
http://www.samsung.com
Appendix
Asia Pacific
AUSTRALIA
1300 362 603
http://www.samsung.com
CHINA
400-810-5858
http://www.samsung.com
010-6475 1880
HONG KONG
(852) 3698 - 4698
http://www.samsung.com/hk
http://www.samsung.com/
hk_en/
INDIA
3030 8282
http://www.samsung.com
1800 110011
1800 3000 8282
1800 266 8282
INDONESIA
0800-112-8888
http://www.samsung.com
021-5699-7777
JAPAN
0120-327-527
http://www.samsung.com
MALAYSIA
1800-88-9999
http://www.samsung.com
NEW ZEALAND
0800 SAMSUNG (0800 726 http://www.samsung.com
786)
PHILIPPINES
1-800-10-SAMSUNG
(726-7864)
http://www.samsung.com
1-800-3-SAMSUNG
(726-7864)
1-800-8-SAMSUNG
(726-7864)
02-5805777
SINGAPORE
1800-SAMSUNG(726-7864) http://www.samsung.com
TAIWAN
0800-329-999
http://www.samsung.com
THAILAND
1800-29-3232
http://www.samsung.com
02-689-3232
VIETNAM
1 800 588 889
http://www.samsung.com
Middle East & Africa
BAHRAIN
8000-4726
JORDAN
800-22273
SOUTH AFRICA
0860-SAMSUNG(726-7864) http://www.samsung.com
TURKEY
444 77 11
http://www.samsung.com
U.A.E
800-SAMSUNG(726-7864)
http://www.samsung.com
Terms
Dot Pitch
The image on a monitor is composed of red, green and blue
dots. The closer the dots, the higher the resolution. The distance between two dots of the same color is called the 'Dot
Pitch'. Unit: mm
88
Appendix
Vertical Frequency
The screen must be redrawn several times per second in
order to create and display an image for the user. The frequency of this repetition per second is called the Vertical
Frequency or Refresh Rate. Unit: Hz
Example: If the same light repeats itself 60 times per second, this is regarded as 60 Hz.
Horizontal Frequency
The time to scan one line connecting the right edge to the
left edge of the screen horizontally is called the Horizontal
Cycle. The inverse number of the Horizontal Cycle is called
Horizontal Frequency. Unit: kHz
Interlace and Non-Interlace
Methods
Showing the horizontal lines of the screen from the top to
the bottom sequentially is called the Non-Interlace method
while showing odd lines and then even lines in turn is called
the Interlace method. The Non-Interlace method is used for
the majority of monitors to ensure a clear image. The Interlace method is the same as that used in TVs.
Plug & Play
This is a function that provides the best quality screen for
the user by allowing the computer and the monitor to exchange information automatically. This monitor follows the
international standard VESA DDC for the Plug & Play function.
Resolution
The number of horizontal and vertical dots used to compose
the screen image is called the 'resolution'. This number
shows the accuracy of the display. A high resolution is good
for performing multiple tasks as more image information can
be shown on the screen.
Example: If the resolution is 1360(1920) x 768(1080), this
means the screen is composed of 1360(1920) horizontal
dots (horizontal resolution) and 768(1080) vertical lines
(vertical resolution).
SRS TS XT
Multiple
(MDC)
Display
This feature outputs sonorous and vivid 3D sound as for 5.1
channel speaker sound but through a 2-channel speaker. It
has a good effect when stereo signals are input.
Control
A Multiple Display Control (MDC) is an application allowing
various displays to be easily and simultaneously operated
on a PC. RS-232C, a standard of serial communication, is
used for communicating between a PC and a display.
Correct Disposal
Correct Disposal of This Product (Waste Electrical & Electronic Equipment) - Europe only
(Applicable in the European Union and other European countries with
separate collection systems)
This marking on the product, accessories or literature indicates that the
product and its electronic accessories (e.g. charger, headset, USB cable)
should not be disposed of with other household waste at the end of their
working life. To prevent possible harm to the environment or human
health from uncontrolled waste disposal, please separate these items
89
Appendix
Correct Disposal of This Product (Waste Electrical & Electronic Equipment) - Europe only
from other types of waste and recycle them responsibly to promote the
sustainable reuse of material resources.
Household users should contact either the retailer where they purchased
this product, or their local government office, for details of where and how
they can take these items for environmentally safe recycling.
Business users should contact their supplier and check the terms and
conditions of the purchase contract. This product and its electronic accessories should not be mixed with other commercial wastes for disposal.
Correct disposal of batteries in this product - Europe only
(Applicable in the European Union and other European countries with
separate battery return systems.)
This marking on the battery, manual or packaging indicates that the batteries in this product should not be disposed of with other household
waste at the end of their working life. Where marked, the chemical symbols Hg, Cd or Pb indicate that the battery contains mercury, cadmium
or lead above the reference levels in EC Directive 2006/66. If batteries
are not properly disposed of, these substances can cause harm to human
health or the environment.
To protect natural resources and to promote material reuse, please separate batteries from other types of waste and recycle them through your
local, free battery return system.
Note
The rechargeable battery incorporated in this product is not user replaceable. For information
on its replacement, please contact your service provider.
Authority
Information in this document is subject to change without notice.
© 2010 Samsung Electronics Co., Ltd. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co., Ltd. is strictly forbidden.
Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental
or consequential damages in connection with the furnishing, performance, or use of this material.
Samsung is the registered trademark of Samsung Electronics Co., Ltd.; Microsoft, Windows
and Windows NT are registered trademarks of Microsoft Corporation; VESA, DPM and DDC
are registered trademarks of Video Electronics Standard Association; the ENERGY STAR®
name and logo are registered trademarks of the U.S. Environmental Protection Agency
(EPA). All other product names mentioned herein may be the trademarks or registered trademarks of their respective owners.
90
Appendix
91
Download PDF