Samsung | 400UXN | Samsung 400UXN Benutzerhandbuch

SyncMaster 400UXn,460UXn
LCD Monitor
User Manual
Safety Instructions
Notational
Note
These safety instructions must be followed to ensure your safety and prevent property damage.
Make sure to read the instructions carefully and use the product in the correct manner.
Warning / Caution
Failure to follow directions noted by this symbol could result in bodily harm
or damage to the equipment.
Notational Conventions
Prohibited
Important to read and understand at all times
Do not disassemble
Disconnect the plug from the
outlet
Do not touch
Ground to prevent an electric
shock
Power
When not used for extended period of time, set your computer to DPM.
If using screen saver, set it to active screen mode.
The images here are for reference only, and are not applicable in all cases (or
countries).
Shortcut to Anti-Afterimage Instructions
Do not use a damaged power cord or plug or a damaged or loose power
outlet.
•
Otherwise, this may result in electric shock or fire.
Do not touch the power plug with wet hands when removing or plugging the plug into the outlet.
•
Otherwise, this may result in electric shock.
Make sure to connect the power cord to a grounded power outlet.
•
Otherwise, it may result in electric shock or personal injury.
Ensure that the power plug is plugged into the power outlet firmly and
correctly.
•
Otherwise, this may result in fire.
Safety Instructions
Do not forcefully bend or pull the power plug and do not place any
heavy material on it.
•
Otherwise, this may result in fire.
Do not connect multiple appliances to the same power outlet.
•
Otherwise, this may cause fire due to overheating.
Do not disconnect the power cord while using the product.
•
Otherwise, this may result in damage to the product due to electric
shock.
To disconnect the apparatus from the mains, the plug must be pulled
out from the mains socket, therefore the mains plug shall be readily operable.
•
This may cause electric shock or fire.
Use only the power cord provided by our company. Do not use the
provided power cord of another product.
•
Otherwise, this may result in fire or electric shock.
Installation
Be sure to contact an authorized Service Center when installing your monitor in
a location with heavy dust, high or low temperatures, high humidity, and exposed
to chemical substances and where it operates for 24 hours such as at airports,
train stations etc.
Failure to do so may cause serious damage to your monitor.
Ensure that at least two persons lift and move the product.
•
Otherwise, it may be dropped and cause personal injury, and/or damage the product.
When installing the product in a cabinet or rack, make sure that the
front end of the bottom of the product does not project out.
•
Otherwise, it may fall or cause personal injury.
•
Use a cabinet or rack of a size appropriate to the product.
DO NOT PLACE CANDLES, MOSQUITO REPELLANT, CIGARETTES AND ANY HEATING APPLIANCES NEAR THE PRODUCT.
•
Otherwise, this may result in fire.
Keep heating appliances as far away from the power cord or the product as possible.
•
Otherwise, this may result in electric shock or fire.
Safety Instructions
Do not install it in a badly ventilated location such as a bookcase or
closet.
•
Otherwise, this may result in fire due to an increase in the internal
temperature.
When putting the product down, make sure to put it down softly.
•
Otherwise, this may result in damage to the screen display.
Do not place the front of the product on the floor.
•
Otherwise, this may result in damage to the screen display.
Ensure that an authorized installation company installs the wall mount.
•
Otherwise, it may fall and cause personal injury.
•
Make sure to install the specified wall mount.
Install your product in a well ventilated location. Ensure that there is
a clearance of more than 10 cm from the wall.
•
Otherwise, it may result in fire due to an increase in the internal temperature.
Ensure that the packaging vinyl is kept away from children.
•
Otherwise, it may result in serious harm (suffocation) if children play
with it.
If the height of your monitor is adjustable, do not place any object or
part of your body on the stand when lowering it.
•
This may cause damage to the product or the person carrying it.
Clean
When cleaning the monitor case or the surface of the TFT-LCD screen, wipe
with a slightly moistened, soft fabric.
Do not spray cleaner directly onto the surface of the product.
•
Otherwise, this may result in the discoloration and distortion of the
structure and the screen surface may peel off.
Clean the product using a soft cloth with a monitor cleaner only. If
you must use a cleaner other than the monitor cleaner, dilute it with water
at a ratio of 1:10.
When cleaning the power plug pins or dusting the power outlet, clean
it with a dry cloth.
•
Otherwise, it may result in fire.
Safety Instructions
When cleaning the product, make sure to disconnect the power cord.
•
Otherwise, it may result in electric shock or fire.
When cleaning the product, disconnect the power cord and clean it
softly with a dry cloth.
•
(Do not use chemicals such as wax, benzene, alcohol, thinner, mosquito repellant, lubricant, or cleaner.) These may change the appearance of the product surface and peel off the indication labels on the
product.
Since the product housing is easily scratched, make sure to use the
specified cloth only.
•
Use the specified cloth adding only a little water. As the product may
be scratched if there is any foreign material on the cloth, make sure
to shake it thoroughly before using it.
When cleaning the product, do not spray water directly onto the main
body of the product.
•
Ensure that water does not enter the product and that it is not wet.
•
Otherwise, this may result in electric shock, fire or a malfunction.
Others
The product is a high voltage product. Ensure that users do not disassemble, repair or modify the product themselves.
•
Otherwise, this may result in electric shock or fire. If the product
needs to be repaired, contact a Service Center.
If there is a strange smell or a strange sound or smoke is coming from
the product, disconnect the power plug immediately and contact a Service
Center.
•
Otherwise, this may result in electric shock or fire.
Do not place this product in a location exposed to moisture, dust,
smoke, water, or in a car.
•
Otherwise, this may result in electric shock or fire.
When you drop the product or the case is broken, turn the power off
and disconnect the power cord. Contact a Service Center.
•
Otherwise, this may result in electric shock or fire.
If thunder or lightening is occurring, do not touch the power cord or
antenna cable.
•
Otherwise, this may result in electric shock or fire.
Safety Instructions
Do not try to move the monitor by pulling only the wire or the signal
cable.
•
Otherwise, it may fall and result in electric shock, damage to the
product or fire due to damage to the cable.
Do not lift or move the product back and forwards or right and left
while only holding the power cord or signal cables.
•
Otherwise, it may fall and result in electric shock, damage to the
product or fire due to damage to the cable.
Make sure that the ventilating opening is not blocked by a table or
curtain.
•
Otherwise, it may result in fire due to an increase in the internal temperature.
Do not place any containers containing water, vases, flowerpots, medicines as well as any metal on the product.
•
If water or a foreign material enters the product, disconnect the power
cord and contact a Service Center.
•
This may result in a product malfunction, electric shock, or fire.
Do not use or keep combustible spray or flammable material near the
product.
•
Otherwise, this may result in an explosion or fire.
Do not insert any metal, such as chopsticks, coins, pins and steels, or
inflammable objects, such as matches or paper, inside the product
(through the ventilating openings, input and output terminals, etc).
•
If water or foreign material enters the product, disconnect the power
cord and contact a Service Center.
•
Otherwise, this may result in electric shock or fire.
When using a fixed screen for a long time, an afterimage or stain may
occur.
•
If you are not using your product for a long period of time, put it into
sleep mode or use a moving screen saver.
Set a resolution and frequency appropriate to the product.
•
Otherwise, your eyesight may be damaged.
When using headphones or earphones, do not turn the volume too high.
•
Having the sound too loud may damage your hearing.
If you continually move closer to the product screen, your eyesight
may be failing.
Safety Instructions
Take a rest for at least five (5) minutes after using the monitor for one
(1) hour.
This reduces the weariness of your eyes.
Do not install it in an unstable location such as an unstable rack or
uneven surface or a location exposed to vibrations.
•
Otherwise, it may fall and cause personal injury and/or damage the
product.
•
If you use the product in a location exposed to vibrations, it may
damage the product and result in fire.
When moving the product, turn the power off and disconnect the power
plug, antenna cable, and all the cables connected to the product.
•
Otherwise, it may result in electric shock or fire.
Ensure that children do not hang onto the product or climb up onto the
product.
•
The product may fall and cause personal injury or death.
If you do not use the product for a long period of time, disconnect the
power cord from the power outlet.
•
Otherwise, this may result in overheating or fire due to dust, and may
result in fire due to electric shock or leakage.
Do not place any heavy items or toys or confectionery, such as cookies
etc. that may attract the attentions of children onto the product.
•
Your children may hang onto the product causing it to fall and this
may result in personal injury or death.
Be careful that children do not place the battery in their mouths when
removed from the remote control. Place the battery in a location that
children or infants cannot reach.
•
If children have had the battery in their mouths, consult your doctor
immediately.
When replacing the battery, insert it with right polarity (+, -).
•
Otherwise, the battery may become damaged or it may cause fire,
personal injury or damage due to leakage of the internal liquid.
Use only the specified standardized batteries, and do not use a new
battery and a used battery at the same time.
•
Otherwise, the batteries may be damaged or cause fire, personal injury or damage due to a leakage of the internal liquid.
The batteries (and rechargeable batteries) is not ordinary refuse and
must be returned for recycling purposes. The customer is responsible for
returning the used or rechargeable batteries for recycling purposes as the
consumer.
•
The customer can return used or rechargeable batteries to a nearby
public recycling center or to a store selling the same type of the battery
or rechargeable battery.
Safety Instructions
Do not place the product in a location exposed to direct sunlight or
near any heat such as a fire or heater.
•
This may reduce the lifetime of the product, and may result in fire.
Do not drop any objects onto the product or cause any impact to the
product.
•
Otherwise, this may result in electric shock or fire.
Do not use a humidifier or kitchen table near the product.
•
Otherwise, this may result in electric shock or fire.
When there is a gas leak, do not touch the product or the power plug
but ventilate immediately.
•
If a spark occurs, it may cause an explosion or fire.
If the product has been turned on for a long time, the display panel
becomes hot. Do not touch it.
•
Keep the small accessories in a location out of the reach of children.
Be careful when adjusting the angle of the product or the height of the
stand.
•
This may result in personal injury as your hand or fingers may become caught.
•
Also, if you tilt the product too far, it may fall and cause personal
injury.
Do not install the product in a location low enough for children to
reach.
•
Otherwise, it may fall and result in personal injury.
•
Since the front part of the product is heavy, install the product on a
level and stable surface.
Do not put any heavy objects on the product.
•
This may result in personal injury and/or damage to the product.
Introduction
-- 400UXn -Package Contents
Note
Please make sure the following items are included with your LCD Display.
If any items are missing, contact your dealer.
Contact a local dealer to buy optional items.
Note
This stand is not for the Floor Standing Type.
Unpacking
LCD Display
Manuals
Quick Setup Guide
Warranty Card
(Not available in all locations)
Cables
D-Sub Cable
Power Cord
User's Guide
Introduction
Others
Remote Control
Batteries (AAA X 2)
BNC to RCA Adaptor Jack
(Not available in all locations)
Sold separately
DVI Cable
Wall Mount KIT
Semi Stand KIT
Calibrater
BNC Cable
-- 400UXn -Your LCD Display
Front
MENU button [MENU]
LAN Cable
For more information on the
use of the calibrater, see Natural Color Expert Help.
Introduction
Opens the on-screen menu and exits from the menu. Also use to exit the OSD menu
or return to the previous menu.
Navigate buttons (Up-Down buttons)
Moves from one menu item to another vertically or adjusts selected menu values.
Adjust buttons (Left-Right buttons) / Volume buttons
Moves from one menu item to another horizontally or adjusts selected menu values. When OSD is not on the screen, push the button to adjust volume.
ENTER button [ENTER]
Activates a highlighted menu item.
SOURCE button [SOURCE]
Switches from PC mode to Video mode. Changing the source is only allowed for
external devices that are connected to the LCD Display at the time.
[PC] → [BNC] → [DVI] → [AV] → [S-Video] → [Component] → [HDMI]
→ [MagicInfo]
>> Click here to see an animation clip
PIP
Push the PIP button to turn the PIP screen On / Off.
More than one PIP cannot overlap on screen as BNC and the component use the
same terminal.
>> Click here to see an animation clip
•
PC
AV / S-Video / Component / HDMI Mode
•
BNC
AV / S-Video / HDMI Mode
•
DVI
AV / S-Video / Component Mode
•
AV / S-Video
PC / BNC / DVI Mode
•
Component
PC / DVI Mode
•
HDMI
PC / BNC Mode
Power button [
]
Use this button for turning the LCD Display on and off.
Power indicator
Shows PowerSaver mode by blinking green
Introduction
Note
See PowerSaver described in the manual for further information regarding power
saving functions. For energy conservation, turn your LCD Display OFF when it
is not needed or when leaving it unattended for long periods.
Remote Control Sensor
Aim the remote control towards this spot on the LCD Display.
Rear
Note
For detailed information concerning cable connections, refer to Connecting Cables under Setup. The
LCD Display 's configuration at the back may vary slightly depending on the LCD Display model.
POWER S/W ON [ │ ] / OFF [O]
Switches the LCD Display On/Off.
POWER IN
The power cord plugs into the LCD Display and
the wall plug.
Introduction
REMOTE OUT/IN
You can use a wired remote control by connecting
it to your LCD Display.
RS232C OUT/IN (RS232C Serial PORT)
MDC(Multiple Display Control) Program Port
DVI / PC / HDMI IN [PC/DVI/BNC AUDIO
IN] (PC/DVI/BNC/HDMI Audio Connection Terminal (Input))
DVI / PC / HDMI IN [HDMI]
Connect the HDMI terminal at the back of your
LCD Display to the HDMI terminal of your digital output device using a HDMI cable.
DVI / PC / HDMI IN [RGB](PC Video Connection Terminal)
Using a D-Sub Cable (15 pin D-Sub) - PC mode
(Analog PC)
DVI / PC / HDMI IN [DVI(HDCP)] (PC
Video Connection Terminal)
Using a DVI Cable (DVI-D to DVI-D) - DVI
mode (Digital PC)
COMPONENT AUDIO IN [L-AUDIO-R]
(Component Audio Connection Terminal (Input))
BNC/COMPONENT OUT [R/PR, G/Y, B/
PB, H, V] (BNC/Component Connection Terminal (Output))
BNC (Analog PC) Connection: connecting the R,
G, B, H, V ports
Component Connection: connecting the PR, Y,
PB ports
BNC/COMPONENT IN [R/PR, G/Y, B/PB,
H, V](BNC/Component Connection Terminal
(Input))
Introduction
AV AUDIO IN [L-AUDIO-R] (LCD Display
Audio Connection Terminal (Input))
AV OUT [VIDEO](VIDEO Connection Terminal)
AV mode (Output)
AV IN [VIDEO](VIDEO Connection Terminal) (Input)
AV OUT [S-VIDEO] (S-VIDEO Connection
Terminal)
S-VIDEO mode (Output)
AV IN [S-VIDEO](S-VIDEO Connection
Terminal) (Input)
EXT SPEAKER(8 Ω)[- - L - +, - - R - +] (EXT
Speaker Connection Terminal)
AUDIO OUT [L-AUDIO-R] (LCD Display
Audio Connection Terminal (Output))AUDIO
OUT is the terminal for sound output of PC, DVI
or BNC.
LAN (LAN Connection Terminal)
USB(USB Connection Terminal)
Keyboard / Mouse, Mass Storage Device Compatible.
Note
The number of LCD Displays that can be connected to loopout may differ depending on the
cables, signal source etc. With cables where there
is no degradation or signal source, up to ten LCD
Displays can be connected.
Note
See Connecting Cables for further information regarding cable connections.
Introduction
-- 400UXn -Remote Control
Note
The performance of the remote control may be affected by a TV or other electronic device operating
near the LCD Display , causing a malfunction due to interference with the frequency.
ON / OFF
MagicInfo
MDC
LOCK
MagicInfo buttons
+100 DEL
VOL
MUTE
TTX/MIX
MENU
ENTER
P.MODE
AUTO
ENTER/PRE-CH
CH/P
SOURCE
INFO
EXIT
Up-Down Left-Right buttons
S.MODE
STILL
FM RADIO
P.SIZE
SRS
DUAL/MTS
PIP
SOURCE
SWAP
SIZE
REW
Introduction
STOP
PLAY/PAUSE
FF
1. ON / OFF
Turns the LCD Display On/Off.
2. MagicInfo
MagicInfo Quick Launch Button.
3. MDC
MDC Quick Launch Button.
4. LOCK
Activates or deactivates all function keys on both the remote control and the LCD Display except for the Power and LOCK buttons.
5. MagicInfo buttons
MagicInfo Quick Launch Button.
6. +100 DEL
•
Alphanumeric: Used to enter the Internet address.
•
DEL: Functions as the backspace.
•
SYMBOL: Used to enter the symbols. (.O_-)
•
ENTER: Used to enter values.
Press to select channels over 100. For example, to select channel
121, press "+100", then press "2" and "1".
- This fuction does not work for this LCD Display.
7. VOL
Adjusts the audio volume.
8.
Pauses (mutes) the audio output temporarily. This is displayed on
the lower left corner of the screen. The audio resumes if MUTE
or - VOL + is pressed in the Mute mode.
9.
MUTE
TTX/MIX
TV channels provide text information services via teletext.
- This fuction does not work for this LCD Display.
10.
MENU
Opens the on-screen menu and exits from the menu screen or
closes the screen adjustment menu.
11.
ENTER
Activates a highlighted menu item.
12.
P.MODE
When you press this button, current picture mode is displayed on
the lower center of the screen.
AV / S-Video / Component : P.MODE
The LCD Display has four automatic picture settings that are preset at the factory. Then push button again to circle through available preconfigured modes. ( Dynamic → Standard → Movie
→ Custom )
PC / DVI / BNC : M/B (MagicBright)
MagicBright is a new feature providing the optimum viewing
environment depending on the contents of the image you are
Introduction
watching. Then push button again to circle through available preconfigured modes. (Entertain → Internet → Text → Custom )
13. AUTO
14.
ENTER/PRE-CH
Adjusts the screen display automatically in PC mode. By changing
the resolution in the control panel, auto function is performed.
Returns to the immediately previous channel.
- This fuction does not work for this LCD Display.
15.
CH/P
In TV mode, selects TV channels.
- This fuction does not work for this LCD Display.
16.
SOURCE
Changes the video source.
17.
INFO
The current picture information is displayed in the top left corner
of the screen.
18.
EXIT
Exits from the menu screen.
19. Up-Down Left-Right buttons
Moves from one menu item to another horizontally, vertically or
adjusts selected menu values.
20.
When pressing this button, the current mode is displayed at the
bottom centre of the screen. The LCD Display has a built-in high
fidelity stereo amplifier. Then press the button again to circle
through available preconfigured modes. ( Standard → Music
→ Movie → Speech → Custom )
S.MODE
21. STILL
Press the button once to freeze the screen. Press it again to unfreeze.
22. FM RADIO
Turns the FM Radio on/off. In PC/DVI mode, sets the SOUND
to FM Radio. In general Video mode, selects FM Radio, and turns
off the screen. In areas where the signal is weak, noise may occur
during FM radio broadcasts.
- This fuction does not work for this LCD Display.
23. P.SIZE
24.
25.
SRS
DUAL/MTS
Press to change the screen size.
SRS
DUALSTEREO/MONO, DUAL l / DUAL ll and MONO/NICAM
MONO/NICAM STEREO can be operated depending on the
broadcasting type by using the DUAL button on the remote control
while watching TV.
MTSYou can select MTS (Multichannel Television Stereo) mode.
FM Stereo
Audio Type
MTS/S_Mode
Default
Mono
Mono
Manual Change
Stereo
Mono ↔ Stereo
SAP
Mono ↔ SAP
Mono
Introduction
- This fuction does not work for this LCD Display.
26.
PIP
Every time you press the button, a PIP screen appears.
27.
SOURCE
Changes the source of the PIP window signal.
28. SWAP
Swaps the contents of the PIP and main image. The image in the
PIP window will appear on the main screen, and the main screen
image will appear in the PIP window.
29.
SIZE
Switches the PIP Picture Size.
30.
REW
Rewind
31.
32.
33.
STOP
PLAY / PAUSE
FF
-- 400UXn -Mechanical Layout
Mechanical Layout
NETWORK MODEL SIZE
Stop
Play/Pause
Fast forward
Introduction
LCD Display Head
NETWORK MODEL SIZE
Installation VESA Bracket
•
When installing VESA, make sure to comply with the international VESA standards.
•
Purchasing VESA Bracket and Installation Information : Please contact your nearest SAMSUNG
Distributor to place an order. After your order is placed, installation professionals will visit you
and install the bracket.
•
At least 2 persons are needed in order to move the LCD Display.
•
SAMSUNG is not responsible for any product damage or any injury caused by installation at
customer's discretion.
Introduction
Dimensions
Notice
For securing the bracket on a wall, use only machine screws of 6 mm diameter and 8 to 12 mm length.
Wall Bracket Installation
•
Contact a technician for installing the wall bracket.
•
SAMSUNG Electronics is not responsible for any damages to the product or harm to customers
when the installation is done by the customer.
•
This product is for installing on cement walls. The product may not stay in place when installed
on plaster or wood.
Components
Only use the components and accessories shipped with the product.
Wall Bracket(1)
Hinge(Left 1, Right Plastic
1)
Hanger
(4)
Screw
(A)(11)
Screw(B) Anchor
(4)
(11)
Wall Bracket Assembly
Note
There are two hinges(left and right). Use the correct one.
1.
Insert and tighten the Captive Screw in the direction of the arrow.
When done, mount the wall bracket on the wall.
Introduction
There are two hinges(left and right). Use the correct one.
2.
A-
Captive Screw
B-
Wall Bracket
C-
Hinge (Left)
D-
Hinge (Right)
Before drilling into the wall, check if the length between the two locking holes at the back of the
product is correct.
If the length is too short or long, loosen all or some of the 4screws on the wall bracket to adjust
the length.
A-
3.
Length between the two locking holes
Check the installation diagram and mark the drill points on the wall. Use the 5.0 mm bit to drill
holes deeper than 35 mm. Fix each anchor in the corresponding hole. Match each of the brackets
and hinge holes to the corresponding anchor holes and insert and tighten the 11 screws A.
Introduction
To mount the product on the wall bracket
The shape of the product may vary depending on the model. (The assemblies of the plastic hanger and
the screw are the same)
1.
Remove the 4 screws on the back of the product.
2.
Insert the screw B into the plastic hanger.
Notice
3.
•
Mount the product on the wall bracket and make sure it is properly fixed to the left and right
plastic hangers.
•
Be careful when installing the product on the bracket as fingers can be caught in the holes.
•
Make sure the wall bracket is securely fixed to the wall, or the product may not stay in place
after installation.
Tighten the 4 screws in step 2 (plastic hanger + screw B)to the rear holes of the product.
Introduction
4.
Remove safety pin (3) and insert the 4 product holders into the corresponding bracket holes (1).
Then place the product(2) so that it is firmly fixed to the bracket. Make sure to re-insert and tighten
the safety pin (3) to securely hold the product to the bracket.
A-
LCD Display
B-
Wall Bracket
C-
Wall
Wall Bracket Angle Adjustment
Adjust the bracket angle to -2° before installing it on the wall.
1.
Fix the product to the wall bracket.
2.
Hold the product at the top in the center and pull it forward (direction of the arrow) to adjust the
angle.
3.
You can adjust the bracket angle between -2° and 15°.
Introduction
Make sure to use the top center, and not the leftor the right side of the product to adjust the angle.
-- 460DXn -Package Contents
Note
Please make sure the following items are included with your LCD Display.
If any items are missing, contact your dealer.
Contact a local dealer to buy optional items.
Note
This stand is not for the Floor Standing Type.
Unpacking
LCD Display
Manuals
Quick Setup Guide
Warranty Card
(Not available in all locations)
User's Guide
Introduction
Cables
D-Sub Cable
Power Cord
Remote Control
Batteries (AAA X 2)
Others
BNC to RCA Adaptor Jack
(Not available in all locations)
Sold separately
DVI Cable
Wall Mount KIT
Semi Stand KIT
Calibrater
BNC Cable
LAN Cable
For more information on the
use of the calibrater, see Natural Color Expert Help.
Introduction
-- 460DXn -Your LCD Display
Front
MENU button [MENU]
Opens the on-screen menu and exits from the menu. Also use to exit the OSD menu
or return to the previous menu.
Navigate buttons (Up-Down buttons)
Moves from one menu item to another vertically or adjusts selected menu values.
Adjust buttons (Left-Right buttons) / Volume buttons
Moves from one menu item to another horizontally or adjusts selected menu values. When OSD is not on the screen, push the button to adjust volume.
ENTER button [ENTER]
Activates a highlighted menu item.
SOURCE button [SOURCE]
Switches from PC mode to Video mode. Changing the source is only allowed for
external devices that are connected to the LCD Display at the time.
[PC] → [BNC] → [DVI] → [AV] → [S-Video] → [Component] → [HDMI]
→ [MagicInfo]
>> Click here to see an animation clip
PIP
Push the PIP button to turn the PIP screen On / Off.
More than one PIP cannot overlap on screen as BNC and the component use the
same terminal.
>> Click here to see an animation clip
•
PC
Introduction
AV / S-Video / Component / HDMI Mode
•
BNC
AV / S-Video / HDMI Mode
•
DVI
AV / S-Video / Component Mode
•
AV / S-Video
PC / BNC / DVI Mode
•
Component
PC / DVI Mode
•
HDMI
PC / BNC Mode
Power button [
]
Use this button for turning the LCD Display on and off.
Power indicator
Shows PowerSaver mode by blinking green
Note
See PowerSaver described in the manual for further information regarding power
saving functions. For energy conservation, turn your LCD Display OFF when it
is not needed or when leaving it unattended for long periods.
Remote Control Sensor
Aim the remote control towards this spot on the LCD Display.
Rear
Note
For detailed information concerning cable connections, refer to Connecting Cables under Setup. The
LCD Display 's configuration at the back may vary slightly depending on the LCD Display model.
Introduction
POWER S/W ON [ │ ] / OFF [O]
Switches the LCD Display On/Off.
POWER IN
The power cord plugs into the LCD Display and
the wall plug.
REMOTE OUT/IN
You can use a wired remote control by connecting
it to your LCD Display.
RS232C OUT/IN (RS232C Serial PORT)
MDC(Multiple Display Control) Program Port
DVI / PC / HDMI IN [PC/DVI/BNC AUDIO
IN] (PC/DVI/BNC/HDMI Audio Connection Terminal (Input))
DVI / PC / HDMI IN [HDMI]
Connect the HDMI terminal at the back of your
LCD Display to the HDMI terminal of your digital output device using a HDMI cable.
DVI / PC / HDMI IN [RGB](PC Video Connection Terminal)
Using a D-Sub Cable (15 pin D-Sub) - PC mode
(Analog PC)
DVI / PC / HDMI IN [DVI(HDCP)] (PC
Video Connection Terminal)
Using a DVI Cable (DVI-D to DVI-D) - DVI
mode (Digital PC)
Introduction
COMPONENT AUDIO IN [L-AUDIO-R]
(Component Audio Connection Terminal (Input))
BNC/COMPONENT OUT [R/PR, G/Y, B/
PB, H, V] (BNC/Component Connection Terminal (Output))
BNC (Analog PC) Connection: connecting the R,
G, B, H, V ports
Component Connection: connecting the PR, Y,
PB ports
BNC/COMPONENT IN [R/PR, G/Y, B/PB,
H, V](BNC/Component Connection Terminal
(Input))
AV AUDIO IN [L-AUDIO-R] (LCD Display
Audio Connection Terminal (Input))
AV OUT [VIDEO](VIDEO Connection Terminal)
AV mode (Output)
AV IN [VIDEO](VIDEO Connection Terminal) (Input)
AV OUT [S-VIDEO] (S-VIDEO Connection
Terminal)
S-VIDEO mode (Output)
AV IN [S-VIDEO](S-VIDEO Connection
Terminal) (Input)
EXT SPEAKER(8 Ω)[- - L - +, - - R - +] (EXT
Speaker Connection Terminal)
AUDIO OUT [L-AUDIO-R] (LCD Display
Audio Connection Terminal (Output))AUDIO
OUT is the terminal for sound output of PC, DVI
or BNC.
Introduction
LAN (LAN Connection Terminal)
USB(USB Connection Terminal)
Keyboard / Mouse, Mass Storage Device Compatible.
Note
The number of LCD Displays that can be connected to loopout may differ depending on the
cables, signal source etc. With cables where there
is no degradation or signal source, up to ten LCD
Displays can be connected.
Note
See Connecting Cables for further information regarding cable connections.
-- 460DXn -Remote Control
Note
The performance of the remote control may be affected by a TV or other electronic device operating
near the LCD Display , causing a malfunction due to interference with the frequency.
Introduction
ON / OFF
MagicInfo
MDC
LOCK
MagicInfo buttons
+100 DEL
VOL
MUTE
TTX/MIX
MENU
ENTER
P.MODE
AUTO
ENTER/PRE-CH
CH/P
SOURCE
INFO
EXIT
Up-Down Left-Right buttons
S.MODE
STILL
FM RADIO
P.SIZE
SRS
DUAL/MTS
PIP
SOURCE
SWAP
SIZE
REW
STOP
PLAY/PAUSE
FF
1. ON / OFF
Turns the LCD Display On/Off.
2. MagicInfo
MagicInfo Quick Launch Button.
Introduction
3. MDC
MDC Quick Launch Button.
4. LOCK
Activates or deactivates all function keys on both the remote control and the LCD Display except for the Power and LOCK buttons.
5. MagicInfo buttons
MagicInfo Quick Launch Button.
6. +100 DEL
•
Alphanumeric: Used to enter the Internet address.
•
DEL: Functions as the backspace.
•
SYMBOL: Used to enter the symbols. (.O_-)
•
ENTER: Used to enter values.
Press to select channels over 100. For example, to select channel
121, press "+100", then press "2" and "1".
- This fuction does not work for this LCD Display.
7. VOL
8.
Adjusts the audio volume.
MUTE
9.
TTX/MIX
Pauses (mutes) the audio output temporarily. This is displayed on
the lower left corner of the screen. The audio resumes if MUTE
or - VOL + is pressed in the Mute mode.
TV channels provide text information services via teletext.
- This fuction does not work for this LCD Display.
10.
MENU
Opens the on-screen menu and exits from the menu screen or
closes the screen adjustment menu.
11.
ENTER
Activates a highlighted menu item.
12.
P.MODE
When you press this button, current picture mode is displayed on
the lower center of the screen.
AV / S-Video / Component : P.MODE
The LCD Display has four automatic picture settings that are preset at the factory. Then push button again to circle through available preconfigured modes. ( Dynamic → Standard → Movie
→ Custom )
PC / DVI / BNC : M/B (MagicBright)
MagicBright is a new feature providing the optimum viewing
environment depending on the contents of the image you are
watching. Then push button again to circle through available preconfigured modes. (Entertain → Internet → Text → Custom )
13. AUTO
14.
ENTER/PRE-CH
Adjusts the screen display automatically in PC mode. By changing
the resolution in the control panel, auto function is performed.
Returns to the immediately previous channel.
- This fuction does not work for this LCD Display.
15.
CH/P
In TV mode, selects TV channels.
Introduction
- This fuction does not work for this LCD Display.
16.
SOURCE
Changes the video source.
17.
INFO
The current picture information is displayed in the top left corner
of the screen.
18.
EXIT
Exits from the menu screen.
19. Up-Down Left-Right buttons
20.
S.MODE
Moves from one menu item to another horizontally, vertically or
adjusts selected menu values.
When pressing this button, the current mode is displayed at the
bottom centre of the screen. The LCD Display has a built-in high
fidelity stereo amplifier. Then press the button again to circle
through available preconfigured modes. ( Standard → Music
→ Movie → Speech → Custom )
21. STILL
Press the button once to freeze the screen. Press it again to unfreeze.
22. FM RADIO
Turns the FM Radio on/off. In PC/DVI mode, sets the SOUND
to FM Radio. In general Video mode, selects FM Radio, and turns
off the screen. In areas where the signal is weak, noise may occur
during FM radio broadcasts.
- This fuction does not work for this LCD Display.
23. P.SIZE
Press to change the screen size.
24.
SRS
25.
SRS
DUAL/MTS
DUALSTEREO/MONO, DUAL l / DUAL ll and MONO/NICAM
MONO/NICAM STEREO can be operated depending on the
broadcasting type by using the DUAL button on the remote control
while watching TV.
MTSYou can select MTS (Multichannel Television Stereo) mode.
FM Stereo
Audio Type
MTS/S_Mode
Default
Mono
Mono
Manual Change
Stereo
Mono ↔ Stereo
SAP
Mono ↔ SAP
Mono
- This fuction does not work for this LCD Display.
26.
PIP
Every time you press the button, a PIP screen appears.
27.
SOURCE
Changes the source of the PIP window signal.
28. SWAP
Swaps the contents of the PIP and main image. The image in the
PIP window will appear on the main screen, and the main screen
image will appear in the PIP window.
Introduction
29.
SIZE
Switches the PIP Picture Size.
30.
REW
Rewind
31.
32.
33.
STOP
PLAY / PAUSE
FF
-- 460DXn -Mechanical Layout
Mechanical Layout
NETWORK MODEL SIZE
LCD Display Head
NETWORK MODEL SIZE
Stop
Play/Pause
Fast forward
Introduction
Installation VESA Bracket
•
When installing VESA, make sure to comply with the international VESA standards.
•
Purchasing VESA Bracket and Installation Information : Please contact your nearest SAMSUNG
Distributor to place an order. After your order is placed, installation professionals will visit you
and install the bracket.
•
At least 2 persons are needed in order to move the LCD Display.
•
SAMSUNG is not responsible for any product damage or any injury caused by installation at
customer's discretion.
Dimensions
Notice
For securing the bracket on a wall, use only machine screws of 6 mm diameter and 8 to 12 mm length.
Wall Bracket Installation
•
Contact a technician for installing the wall bracket.
•
SAMSUNG Electronics is not responsible for any damages to the product or harm to customers
when the installation is done by the customer.
•
This product is for installing on cement walls. The product may not stay in place when installed
on plaster or wood.
Components
Only use the components and accessories shipped with the product.
Introduction
Wall Bracket(1)
Hinge(Left 1, Right Plastic
1)
Hanger
(4)
Screw
(A)(11)
Screw(B) Anchor
(4)
(11)
Wall Bracket Assembly
Note
There are two hinges(left and right). Use the correct one.
1.
Insert and tighten the Captive Screw in the direction of the arrow.
When done, mount the wall bracket on the wall.
There are two hinges(left and right). Use the correct one.
2.
A-
Captive Screw
B-
Wall Bracket
C-
Hinge (Left)
D-
Hinge (Right)
Before drilling into the wall, check if the length between the two locking holes at the back of the
product is correct.
If the length is too short or long, loosen all or some of the 4screws on the wall bracket to adjust
the length.
Introduction
A3.
Length between the two locking holes
Check the installation diagram and mark the drill points on the wall. Use the 5.0 mm bit to drill
holes deeper than 35 mm. Fix each anchor in the corresponding hole. Match each of the brackets
and hinge holes to the corresponding anchor holes and insert and tighten the 11 screws A.
To mount the product on the wall bracket
The shape of the product may vary depending on the model. (The assemblies of the plastic hanger and
the screw are the same)
1.
Remove the 4 screws on the back of the product.
Introduction
2.
Insert the screw B into the plastic hanger.
Notice
•
Mount the product on the wall bracket and make sure it is properly fixed to the left and right
plastic hangers.
•
Be careful when installing the product on the bracket as fingers can be caught in the holes.
•
Make sure the wall bracket is securely fixed to the wall, or the product may not stay in place
after installation.
3.
Tighten the 4 screws in step 2 (plastic hanger + screw B)to the rear holes of the product.
4.
Remove safety pin (3) and insert the 4 product holders into the corresponding bracket holes (1).
Then place the product(2) so that it is firmly fixed to the bracket. Make sure to re-insert and tighten
the safety pin (3) to securely hold the product to the bracket.
Introduction
A-
LCD Display
B-
Wall Bracket
C-
Wall
Wall Bracket Angle Adjustment
Adjust the bracket angle to -2° before installing it on the wall.
1.
Fix the product to the wall bracket.
2.
Hold the product at the top in the center and pull it forward (direction of the arrow) to adjust the
angle.
3.
You can adjust the bracket angle between -2° and 15°.
Make sure to use the top center, and not the leftor the right side of the product to adjust the angle.
Connections
Connecting a Computer
Using a Power cord with Earth
•
In the event of failure, the earth lead may cause electric shock. Make sure to
wire the earth lead in correctly, before connecting the AC power. When unwiring the earth lead, make sure to disconnect the AC power in advance.
Note
AV input devices such as DVD players, VCR's or camcorders as well as your computer can be connected to the LCD Display. For detailed information on connecting AV input devices, refer to the User
Controls under Adjusting Your LCD Display.
Connect the power cord for your LCD Display to the power port on the back of
the LCD Display. Trun on the power switch.
There are 3 ways to connect the D-sub to your LCD Display. Choose one of the
following:
Using the D-sub (Analog) connector on the video card.
•
Connect the D-sub to the 15-pin, RGB port on the back of your LCD Display
and the 15 pin D-sub Port on the computer.
Using the DVI (Digital) connector on the video card.
•
Connect the DVI Cable to the DVI(HDCP) port on the back of your LCD
Display and the DVI port on the computer.
Connections
Using the BNC (Analog) connector on the video card.
•
Connect the BNC Cable to the BNC/COMPONENT IN - R, G, B, H, V ports
on the back of your LCD Display and the 15 pin D-sub Port on the computer.
Connect the audio cable for your LCD Display to the audio port on the back of
your computer.
Note
•
Turn on both your computer and the LCD Display.
•
The DVI cable or BNC cable is optional.
•
Contact a local SAMSUNG Electronics Service Center to buy optional items.
Connecting to Other devices
Using a Power cord with Earth
•
In the event of failure, the earth lead may cause electric shock. Make sure to
wire the earth lead in correctly, before connecting the AC power. When unwiring the earth lead, make sure to disconnect the AC power in advance.
Note
AV input devices such as DVD players, VCR's or camcorders as well as your computer can be connected to the LCD Display. For detailed information on connecting AV input devices, refer to the User
Controls under Adjusting Your LCD Display.
Connections
Connecting a VCR
AV input devices such as VCRs or Camcorders are connected via the AV IN
[VIDEO] or AV IN [S-VIDEO] of the LCD Display using an S-VHS or BNC
cable.
Connect the Audio (L) and Audio (R) terminals of a VCR or Camcorders to the
LCD Display 's AV AUDIO IN [L-AUDIO-R] using audio cables.
Note
•
Select AV or S-Video for a connected VCR or Camcorder using the SOURCE button on the front
of the LCD Display or on the remote control.
•
Then, start the VCR or Camcorders with a tape inserted.
•
The S-VHS or BNC cable is optional.
Connecting a DVD Player
Connect a set of audio cables between the COMPONENT AUDIO IN [L-AUDIOR] on the LCD Display and the AUDIO OUT jacks on the DVD player.
Connect a Component cable between the BNC/COMPONENT IN - PR, Y, PB
port on the LCD Display and the PR, Y, PB jacks on the DVD player.
Connections
Note
•
Select Component for the connection to a DVD player using the SOURCE button on the front of
the LCD Display or on the remote control.
•
Then, start the DVD Player with a DVD disc inserted.
•
A component cable is optional.
•
For an explanation of Component video, consult your DVD manual.
Connecting a Camcorder
Locate the A/V output jacks on the camcorder. They are usually found on the side
or back of the camcorder. Connect a set of audio cables between the AUDIO
OUTPUT jacks on the camcorder and the AV AUDIO IN [L-AUDIO-R] on the
LCD Display.
Connect a video cable between the VIDEO OUTPUT jack on the camcorder and
the AV IN [VIDEO] on the LCD Display.
Note
•
Select AV for the Camcorder connection using the SOURCE button on the front of the LCD Display
or on the remote control.
•
Then, start the Camcorders with a tape inserted.
•
The audio-video cables shown here are usually included with a Camcorder.
(If not, check your local electronics store.)
•
If your camcorder is stereo, you need to connect a set of two cables.
Connections
Connecting a DTV Set Top Box
Connect a Component cable between the BNC / COMPONENT IN - PR, Y, PB
port on the LCD Display and the PR, Y, PB jacks on the Set Top Box.
Connect a set of audio cables between the COMPONENT AUDIO IN [L-AUDIOR] on the LCD Display and the AUDIO OUT jacks on the Set Top Box.
Note
•
Select Component for the connection to a DTV Set Top Box using the SOURCE button on the
front of the LCD Display or on the remote control.
•
For an explanation of Component video, see your Set Top Box owner's manual.
Connecting to an Audio System
Note
Connect a set of audio cables between the AUX L, R jacks on the AUDIO SYSTEM and the AUDIO
OUT [L-AUDIO-R] on LCD Display.
Connections
Connecting to a Wired Remote Control
Note
•
You can control your LCD Display by allowing it to receive the remote control signals of other
devices through the REMOTE OUT terminal.
•
You can control a device by allowing it to receive remote control signals from other devices through
the REMOTE IN terminal.
•
Restrictions: Available only if other devices support the wired remote control I/O terminals.
Connecting Using a HDMI Cable
Note
•
Input devices such as digital DVD are connected to the HDMI IN terminal of the LCD Display
using the HDMI cable.
•
You cannot connect a PC to the HDMI IN terminal.
Connecting Using a DVI to HDMI Cable
Connections
Note
•
Connect the DVI output terminal of a digital output device to the HDMI IN terminal of the LCD
Display using a DVI to HDMI cable.
•
Connect the red and white jacks of an RCA to stereo (for PC) cable to the same colored audio
output terminals of the digital output device, and connect the opposite jack to the HDMI / PC /
DVI-D AUDIO IN terminal of the LCD Display.
Connecting a LAN Cable
Using a Power cord with Earth
•
In the event of failure, the earth lead may cause electric shock. Make sure to
wire the earth lead in correctly, before connecting the AC power. When unwiring the earth lead, make sure to disconnect the AC power in advance.
Note
AV input devices such as DVD players, VCR's or camcorders as well as your computer can be connected to the LCD Display. For detailed information on connecting AV input devices, refer to the User
Controls under Adjusting Your LCD Display.
Note
Connect the LAN cable.
Connecting a USB device
Using a Power cord with Earth
•
In the event of failure, the earth lead may cause electric shock. Make sure to
wire the earth lead in correctly, before connecting the AC power. When unwiring the earth lead, make sure to disconnect the AC power in advance.
Note
AV input devices such as DVD players, VCR's or camcorders as well as your computer can be connected to the LCD Display. For detailed information on connecting AV input devices, refer to the User
Controls under Adjusting Your LCD Display.
Connections
Note
You can connect USB devices such as a mouse or keyboard.
Using the Software
Installation MagicInfo Pro
Installation
1.
Insert CD into the CD-ROM drive.
2.
Click the MagicInfo Pro installation file.
3.
When the Install Shield Wizard window appears, click "Next."
4.
Select "I agree to the terms of the license agreement" to accept the terms of use.
5.
You are required to log in to the MagicInfo Pro Server program. Please enter the password to
login. The password cannot be changed when you are logged in.
Using the Software
6.
Choose a folder to install the MagicInfo Pro program.
7.
Click "Install."
Using the Software
8.
The "Installation Status" window appears.
9.
It is recommended restarting the system for the normal operation of the MagicInfo Pro Server
program. Click "Next."
Using the Software
10. When the installation is complete, the MagicInfo Pro executable icon appears on your desktop.
11. Double-click the icon to start the program.
System Requirements
Minimum
CPU
RAM
Ethernet
OS
P1.8
256M
100M/1G
Windows XP WMP 9 or
Windows
later
2000 (Service Pack 4)
Recommen- P3.0Ghz
ded
512M
Application
Adjusting the LCD Display
Direct Functions
Available Modes
•
PC / BNC / DVI
•
AV
•
S-Video
•
Component
•
HDMI
•
MagicInfo
MagicInfo
Moves to the MagicInfo OSD screen.
Adjusting the LCD Display
MDC
Moves to the Multi Control OSD screen.
LOCK
This is the function that locks the OSD in order to keep the current states of settings or prevent others
from adjusting the current settings.
Note
•
When setting the Lock function, you can only operate the power and lock buttons on the remote
control and set.
•
Resetting the password for the function key lock. Press MUTE → 1 → 8 → 6 → On. The password
will be reset to '0000'. The remote control is required for resetting the password.
Lock On
Hold down the MENU button for more than five (5) seconds to activate the OSD adjustment lock
function.
Adjusting the LCD Display
Lock Off
Hold down the MENU button for more than five (5) seconds to deactivate the OSD adjustment lock
function.
Input
Available Modes
•
PC / BNC / DVI
•
AV
•
S-Video
•
Component
•
HDMI
•
MagicInfo
Adjusting the LCD Display
Source List
Use to select PC, BNC, or other external input sources connected to the LCD Display. Use to select
the screen of your choice.
1.
PC
2.
BNC
3.
DVI
4.
AV
5.
S-Video
6.
Component
7.
HDMI
8.
MagicInfo
Note
•
The direct button on the remote control is the 'SOURCE' button.
•
PIP turns off when the LCD Display is switched to an external source.
•
For PC and DVI, this is deactivated if the cable is disconnected.
MENU → ENTER → ENTER →
,
→ ENTER
PIP
Note
Available Modes: PIP ON
When external AV devices such as VCRs or DVDs are connected to the LCD Display , PIP allows
you to watch video from those devices in a small window super-imposed on the PC Video signal.
(Off/On)
Adjusting the LCD Display
Note
•
More than one PIP cannot be overlapped on screen as BNC and the Component use the same
terminal.
•
If you select
,
,
in Size, Position and Transparency will not be activated.
PIP
Turns the PIP Screen Off/On.
•
Off
•
On
Note
The direct button on the remote control is the 'PIP' button.
MENU → ENTER →
Source
,
→ ENTER → ENTER →
,
→ ENTER
Adjusting the LCD Display
Selects the input source for the PIP.
•
PC : AV / S-Video / Component / HDMI Mode
•
BNC : AV / S-Video / HDMI Mode
•
DVI : AV / S-Video / Component Mode
•
AV / S-Video : PC / BNC / DVI Mode
•
Component : PC / DVI Mode
•
HDMI : PC / BNC Mode
Note
The direct button on the remote control is the 'SOURCE' button.
MENU → ENTER →
,
→ ENTER →
,
→ ENTER →
,
→ ENTER
Swap
Swaps the contents of the PIP and main image.
The image in the PIP window will appear on the main screen, and the main screen image will appear
in the PIP window.
Note
The direct button on the remote control is the 'SWAP' button.
MENU → ENTER →
,
→ ENTER →
,
→ ENTER
Adjusting the LCD Display
Size
Changes the Size of the PIP window.
Note
The direct button on the remote control is the 'SIZE' button.
MENU → ENTER →
,
→ ENTER →
,
→ ENTER →
,
→ ENTER
,
→ ENTER →
,
→ ENTER
Position
Changes the Position of the PIP window.
MENU → ENTER →
,
→ ENTER →
Adjusting the LCD Display
Transparency
Adjusts the Transparency of PIP windows.
•
High
•
Medium
•
Low
•
Opaque
MENU → ENTER →
,
→ ENTER →
,
→ ENTER →
,
→ ENTER
Edit Name
Name the input device connected to the input jacks to make your input source selection easier.
1.
PC
2.
BNC
Adjusting the LCD Display
3.
DVI
4.
AV
5.
S-Video
6.
Component
7.
HDMI
MENU → ENTER →
,
→ ENTER →
,
→ ENTER →
,
→ ENTER
Picture [PC / BNC / DVI Mode]
Available Modes
•
PC / BNC / DVI
•
AV
•
S-Video
•
Component
•
HDMI
•
MagicInfo
MagicBright
MagicBright is a new feature providing the optimum viewing environment depending on the contents
of the image you are watching. Currently four different modes are available: Entertain, Internet,
Text and Custom. Each mode has its own pre-configured brightness value. You can easily select one
of the four settings by simply pressing the MagicBright control button.
1.
Entertain
High brightness
For documentations or works involving heavy text.
Adjusting the LCD Display
2.
Internet
Medium brightness
For working with a mixture of images such as texts and graphics.
3.
Text
Normal brightness
For documentations or works involving heavy text.
4.
Custom
Although the values are carefully chosen by our engineers, the pre-configured values may not be
comfortable to your eyes depending on your taste.
If this is the case, adjust the brightness and contrast by using the OSD menu.
Note
The direct button on the remote control is the 'M/B' button.
MENU →
,
→ ENTER → ENTER →
,
→ ENTER
Custom
By using the on-screen menus, the contrast and brightness can be changed to your personal preference.
1.
Contrast
Adjusts the Contrast.
2.
Brightness
Adjusts the Brightness.
Note
By adjusting the picture using the Custom function, MagicBright will change to Custom mode.
Adjusting the LCD Display
MENU →
,
→ ENTER →
,
→ ENTER → ENTER →
,
/ ,
→ ENTER
Color Tone
The color tones can be changed.
1.
Off
2.
Cool
3.
Normal
4.
Warm
5.
Custom
(Available in PC, BNC mode only)
Note
If you set the Color Tone to Cool, Normal, Warm, or Custom, the Color Temp function is disabled.
If you set the Color Tone to Off, the Color Control function is disabled
MENU →
,
→ ENTER →
,
→ ENTER →
,
→ ENTER
Adjusting the LCD Display
Color Control
Adjusts individual Red, Green, Blue color balance.
(Available in PC, BNC mode only)
1.
Red
2.
Green
3.
Blue
Note
If you adjust the picture by using the Color Control function, Color Tone will turn to the Custom
mode.
MENU →
Color Temp
,
→ ENTER →
,
→ ENTER → ENTER → ,
→ ENTER
Adjusting the LCD Display
Color Temp is a measure of the 'warmth' of the image colors.
Note
This function is only enabled if the Color Tone is set to Off.
MENU →
,
→ ENTER →
,
→ ENTER → ,
→ ENTER
Image Lock
Image Lock is used to fine-tune and get the best image by removing noise that creates unstable images
with jitters and shakiness. If satisfactory results are not obtained using the Fine adjustment, use the
Coarse adjustment and then use Fine again.
(Available in PC, BNC mode only)
Coarse
Removes noise such as vertical stripes. Coarse adjustment may move the screen image area. You may
relocate it to the center using the horizontal control menu.
MENU →
,
→ ENTER →
,
→ ENTER → ENTER → ,
→ ENTER
Adjusting the LCD Display
Fine
Removes noise such as horizontal stripes. If the noise persists even after Fine tuning, repeat it after
adjusting the frequency (clock speed).
MENU →
,
→ ENTER →
,
→ ENTER →
,
→ ENTER → ,
→ ENTER
→ ENTER →
/ ,
Position
Adjusts the screen location horizontally and vertically.
MENU →
,
→ ENTER →
,
→ ENTER →
,
,
→ ENTER
Adjusting the LCD Display
Auto Adjustment
The values of Fine, Coarse, Position are adjusted automatically. By changing the resolution in the
control panel, the auto function is performed.
(Available in PC, BNC mode only)
Note
The direct button on the remote control is the 'AUTO' button.
MENU →
,
→ ENTER →
,
→ ENTER
Signal Balance
This is used to make up for the weak RGB signal transmitted by a long signal cable.
(Available in PC, BNC mode only)
Signal Balance
Selects either On or Off with the signal control.
Adjusting the LCD Display
MENU →
,
→ ENTER →
,
→ ENTER → ENTER →
,
→ ENTER
Signal Control
Adjusts the Gain and Sharpness manually.
MENU → , → ENTER →
→ , → , → ENTER
,
→ ENTER →
,
→ ENTER →
,
→ ENTER → ENTER →
Size
The Size can be switched.
1.
16:9
2.
4:3
MENU →
,
→ ENTER →
,
→ ENTER
,
→ ENTER
Adjusting the LCD Display
PIP Picture
Adjusts the PIP Screen Settings.
Note
Available Modes: PIP ON
1.
Contrast
Adjusts the Contrast of the PIP window on the screen.
2.
Brightness
Adjusts the Brightness of the PIP window on the screen.
3.
Sharpness
Adjusts the difference between the lightest and darkest areas of the PIP window.
4.
Color
Adjusts the Color of the PIP window on the screen.
5.
Tint
Adds a natural tone to the PIP window.
Note
You can view a picture from AV, S-Video through the PIP screen in PC, BNC and DVI mode.
Operates only if the video signal is NTSC.
MENU →
,
→ ENTER →
,
→ ENTER →
,
→ ENTER → ,
Picture [ AV / S-Video / Component / HDMI Mode]
Available Modes
•
PC / BNC / DVI
→ ENTER
Adjusting the LCD Display
•
AV
•
S-Video
•
Component
•
HDMI
•
MagicInfo
Mode
The LCD Display has four automatic picture settings ("Dynamic", "Standard", "Movie" and "Custom") that are preset at the factory.
Dynamic, Standard, Movie, or Custom can be activated.
1.
Dynamic
2.
Standard
3.
Movie
4.
Custom
Note
The direct button on the remote control is the 'P.MODE' button.
MENU →
,
→ ENTER → ENTER →
,
→ ENTER
Adjusting the LCD Display
Custom
By using the on-screen menus, the contrast and brightness can be changed to your personal preference.
1.
Contrast
Adds a natural tone to the PIP window.
2.
Brightness
Adjusts the Brightness.
3.
Sharpness
Adjusts the picture Sharpness.
4.
Color
Adjusts the picture Color.
5.
Tint
Adds a natural tone to the display.
Note
Operates only for AV and S-Video mode. Operates only if the video signal is NTSC.
MENU →
,
→ ENTER →
,
→ ENTER → ENTER →
,
→ ,
→ ENTER
Adjusting the LCD Display
Color Tone
The color tones can be changed. The individual Color components are also user adjustable.
1.
Off
2.
Cool2
3.
Cool1
4.
Normal
5.
Warm1
6.
Warm2
Note
If you set the Color Tone to Cool1, Cool2, Normal, Warm1, or Warm2, the Color Temp function
is disabled.
MENU →
Color Temp
,
→ ENTER →
,
→ ENTER →
,
→ ENTER
Adjusting the LCD Display
Color temp is a measure of the 'warmth' of the image colors.
Note
This function is only enabled if the Color Tone is set to Off.
MENU →
,
→ ENTER →
,
→ ENTER → ,
→ ENTER
Size
The Size can be switched.
1.
16:9
2.
Zoom 1
3.
Zoom 2
4.
4:3
Note
The Zoom1, Zoom2 are not available in 1080i (or over 720p) of Component and HDMI.
MENU →
,
→ ENTER →
,
→ ENTER →
,
→ ENTER
Adjusting the LCD Display
Dynamic Contrast
Dynamic Contrast is to automatically detect distribution of inputted visual signal and adjust to create
optimum contrast.
1.
Off
2.
On
MENU →
,
→ ENTER →
,
→ ENTER →
,
→ ENTER
Digital NR (Digital Noise Reduction)
Turns the Digital Noise Reduction feature Off/On. The Digital Noise Reduction feature allows you to
enjoy clearer and crisper images.
1.
Off
2.
On
MENU →
,
→ ENTER →
,
→ ENTER →
,
→ ENTER
Adjusting the LCD Display
Film Mode
Turns Film Mode Off/On.
The Film Mode feature offers you a theater-quality viewing experience.
(Not available in HDMI Mode)
1.
Off
2.
On
MENU →
,
→ ENTER →
PIP Picture
Adjusts the PIP Screen Settings.
Note
Available Modes: PIP ON
,
→ ENTER →
,
→ ENTER
Adjusting the LCD Display
1.
Contrast
Adjusts the Contrast of the PIP window on the screen.
2.
Brightness
Adjusts the Brightness of the PIP window on the screen.
MENU →
,
→ ENTER →
,
→ ENTER →
,
→ ENTER → ,
Sound
Available Modes
•
PC / BNC / DVI
•
AV
•
S-Video
•
Component
•
HDMI
•
MagicInfo
Mode
The LCD Display has a built-in high fidelity stereo amplifier.
1.
Standard
Selects Standard for the standard factory settings.
2.
Music
Selects Music when watching music videos or concerts.
3.
Movie
→ ENTER
Adjusting the LCD Display
Selects Movie when viewing movies.
4.
Speech
Selects Speech when watching a show that is mostly dialogue (i.e., news).
5.
Custom
Selects Custom if you want to Adjusts the settings according to your personal preferences.
MENU →
,
→ ENTER → ENTER →
,
→ ENTER
Custom
The sound settings can be adjusted to suit your your personal preferences.
1.
Bass
Emphasizes low frequency audio.
2.
Treble
Emphasizes high frequency audio.
3.
Balance
Allows you to Adjusts the sound balance between the left and right speakers.
Note
•
You can hear the sound even when sound value is set to 0.
•
If you adjust sound using Custom function, Mode will turn to Custom mode.
MENU →
,
→ ENTER →
,
→ ENTER →
,
→ ENTER → ,
→ ENTER
Adjusting the LCD Display
Auto Volume
Reduces the difference in volume control between broadcasters.
1.
Off
2.
On
MENU →
,
→ ENTER →
,
→ ENTER →
,
→ ENTER
SRS TS XT
SRS TS XT is a patented SRS technology that solves the problem of playing 5.1 multichannel content
over two speakers. TruSurround delivers a compelling, virtual surround sound experience through any
two-speaker playback system, including internal television speakers. It is fully compatible with all
multichannel formats.
1.
Off
2.
On
Adjusting the LCD Display
Note
The direct button on the remote control is the 'SRS' button.
MENU →
,
→ ENTER →
,
→ ENTER →
,
→ ENTER
,
→ ENTER
Sound Select
Selects either Main or Sub when PIP is On.
Note
Available Modes: PIP ON
1.
Main
2.
Sub
MENU →
,
→ ENTER →
Setup
Available Modes
•
PC / BNC / DVI
•
AV
•
S-Video
•
Component
•
HDMI
•
MagicInfo
,
→ ENTER →
Adjusting the LCD Display
Language
You can choose one of 11 languages.
Note
The language chosen affects only the language of the OSD. It has no effect on any software running
on the computer.
MENU →
,
→ ENTER → ENTER →
,
→ ENTER
Time
Selects from one of 4 time settings, Clock Set, Sleep Timer, On Timer, and Off Timer.
Note
When selecting Yes for the On Timer or Off Timer when the Clock is not set up, a guiding message
pops up: "Set the clock first.".
Adjusting the LCD Display
Clock Set
Current Time Setting.
MENU →
,
→ ENTER →
,
→ ENTER → ENTER → ,
→ ENTER
Sleep Timer
Turns the LCD Display off automatically at certain times. (Off, 30, 60, 90, 120, 150, 180)
MENU → , → ENTER →
→ , → ENTER
,
→ ENTER →
,
→ ENTER → ,
→
,
→ ENTER → ,
Adjusting the LCD Display
On Timer
Turns the LCD Display on automatically at a preset time. Controls the mode and the volume level at
the time the LCD Display turns on automatically.
MENU →
,
→ ENTER →
,
→ ENTER →
,
→ ENTER → ,
→
,
→ ENTER
→
,
→ ENTER
Off Timer
Turns the LCD Display off automatically at a preset time.
MENU →
,
→ ENTER →
,
→ ENTER →
,
→ ENTER → ,
Adjusting the LCD Display
Menu Transparency
Change the transparency of the background of the OSD.
1.
High
2.
Medium
3.
Low
4.
Opaque
MENU →
,
→ ENTER →
,
→ ENTER →
,
→ ENTER
,
→ ENTER → [0∼ 9] → [0∼ 9] → [0∼ 9]
Safety Lock PIN
The password can be changed.
MENU →
,
→ ENTER →
Adjusting the LCD Display
Energy Saving
This feature adjusts the power consumption of the unit in order to save energy.
1.
Off
2.
On
Note
If you want to reduce the standby power consumption, set Energy Saving to On. However, when
Energy Saving is On, you cannot use the remote Power On function of the MDC and the WOL (Wake
On LAN) function of MagicInfo.
MENU →
,
→ ENTER →
,
→ ENTER →
,
→ ENTER → MENU
HDMI Black Level
When a DVD or set-top box is connected to your TV via HDMI, it may cause a degradation in the
screen quality, such as an increase in the black level, a low contrast, or discoloration, etc., depending
Adjusting the LCD Display
on the external device connected. In this case, adjust the screen quality of your TV by configuring the
HDMI black level.
1.
Normal
2.
Low
MENU →
,
→ ENTER →
,
→ENTER→
,
→ ENTER → MENU
Video Wall
A Video Wall is a set of video screens connected together, so that each screen shows a part of the
whole picture or where the same picture is repeated on each screen.
When the Video Wall is on, you can adjust the Video Wall screen setting.
Note
When Video Wall is running, the PIP, Auto Adjustment, Image Lock, and Size functions are not
available. Launching Video Wall while PIP is running, will switch PIP Off. Video Wall does not
operate in MagicInfo mode.
Video Wall
Turns Off/On the Video Wall function of the selected display Off/On.
1.
Off
2.
On
MENU →
,
→ ENTER →
,
→ ENTER → ENTER → ,
→ ENTER
Adjusting the LCD Display
Format
The format can be selected to see a divided screen.
1.
Full
Provides a full screen without any margins.
2.
Natural
Displays a natural image with the original aspect ratio intact.
MENU →
,
→ ENTER →
,
→ ENTER →
,
→ ENTER →
,
→ ENTER
,
→ ENTER
Horizontal
Sets how many parts the screen should be divided horizontally.
Five adjustment levels: 1, 2, 3, 4, and 5.
MENU →
,
→ ENTER →
,
→ ENTER →
,
→ ENTER →
Adjusting the LCD Display
Vertical
Sets how many parts the screen should be divided vertically.
Five adjustment levels: 1, 2, 3, 4, and 5.
MENU →
,
→ ENTER →
,
→ ENTER →
,
→ ENTER →
,
→ ENTER
Screen Divider
The screen can be divided into several images. A number of screens can be selected with a different
layout when dividing.
•
Select a mode in Screen Divider.
•
Select a display in Display Selection.
•
The selection will be set up by pressing a number in the selected mode.
MENU →
,
→ ENTER →
,
→ ENTER →
,
→ ENTER →
,
→ ENTER
Adjusting the LCD Display
Safety Screen
The Safety Screen function is used to prevent afterimages that may appear when a still picture is
displayed on the screen over a long time.
•
The Screen Scroll function scrolls the screen for the specified period of time.
•
This function is not available when the power is turned off.
Safety Screen
Determines whether to turn the Screen Scroll function Off or On.
1.
Off
2.
On
MENU →
Interval
,
→ ENTER →
,
→ ENTER → ENTER →
,
→ ENTER
Adjusting the LCD Display
Determines the time interval to run the Screen Scroll operation. (1~10 Hour)
The time is calculated on the basis of the power on time.
By default, the time is set to 10 hours.
1.
1~10 Hour
MENU →
,
→ ENTER →
,
→ ENTER →
,
→ ENTER →
,
→ ENTER
Second
Determines the time period to run the Screen Scroll operation. (1~5 Second)
By default, the time is set to 5 seconds.
•
Type-Scroll : 1~5 Second
•
Type-Pixel, Bar, Eraser : 10~50 Second
MENU →
Type
,
→ ENTER →
,
→ ENTER →
,
→ ENTER →
,
→ ENTER
Adjusting the LCD Display
You can change the Safety Screen Type.
1.
Scroll
2.
Pixel
3.
Bar
4.
Eraser
MENU →
,
→ ENTER →
,
→ ENTER →
,
→ ENTER →
,
→ ENTER
Resolution Select
When the picture is not displayed properly on the screen when setting the graphics card resolution of
the computer to 1024 x 768 @ 60Hz, 1280 x 768 @ 60Hz, 1360 x 768@ 60Hz or 1366 x768 @ 60Hz,
by using this function(Resolution Select), you can have the picture displayed on the screen in the
specified resolution.
Note
Available in PC/BNC mode only
1.
Off
2.
1024 X 768
3.
1280 X 768
4.
1360 x 768
5.
1366 X 768
Note
Selecting the menu is only allowed when the graphics resolution is set to 1024 x 768 @ 60Hz, 1280 x
768 @ 60Hz, 1360 x 768@ 60Hz or 1366 x768 @ 60Hz.
MENU →
,
→ ENTER →
,
→ ENTER →
,
→ ENTER
Adjusting the LCD Display
Lamp Control
Adjusts the inverter lamp in order to reduce energy consumption.
Note
This function does not operate when Dynamic Contrast is set to On in AV, S-Video, Component
modes.
MENU →
,
→ ENTER →
,
→ ENTER → ENTER → ,
→ ENTER
Power On Adjustment
Adjusts the Power On time for the screen.
Caution: Set the Power On time to be loger to avoid overvoltage.
MENU →
,
→ ENTER →
,
→ ENTER → ENTER →
,
→ ENTER
Adjusting the LCD Display
FAN
Adjusts the FAN.
1.
Normal
2.
Pivot
Note
When pivoting your LCD Display, make sure to select PIVOT for the FAN.
MENU →
,
→ ENTER →
,
→ ENTER →
,
→ ENTER
Reset
Reverts the product settings to factory defaults. DVI source, the Reset function is only available when
PC / DVI is being used.
Note
The Reset function is not available when Video Wall is On.
Adjusting the LCD Display
Image Reset
Note
Available in PC/BNC mode only
MENU →
,
→ ENTER →
,
→ ENTER → ENTER → , → ENTER
Color Reset
Note
Available in PC/BNC mode only
MENU →
,
→ ENTER →
,
→ ENTER → ENTER →
,
→ ENTER
Adjusting the LCD Display
Multi Control
Available Modes
•
PC / BNC / DVI
•
AV
•
S-Video
•
Component
•
HDMI
•
MagicInfo
Multi Control
Assigns an individual ID to the SET.
ID Setup
Assigns distinctive IDs to the SET.
MENU →
,
→ ENTER →
,
→ ENTER → ENTER → [0~9]
Adjusting the LCD Display
ID Input
Use to select the transmitter functions of the individual SET. Only a SET where the ID corresponds to
the transmitter setting becomes activated.
MENU →
,
→ ENTER →
,
→ ENTER → ENTER → [0~9]
MagicInfo
Available Modes
•
PC / BNC / DVI
•
AV
•
S-Video
•
Component
•
HDMI
•
MagicInfo
Note
•
The operating system for this set only supports English so the other languages might be corrupted
on the screen.
•
For MagicInfo, a remote control is available for MagicInfo. However, it is recommended using
a separate USB keyboard.
•
For MagicInfo in Device mode, moving external devices while booting may cause errors. Set up
external devices only if the LCD Display turns on.
•
Do not unplug the LAN cable used for the network (ex: video display). Otherwise, the program
(MagicInfo) may stop. If you do unplug the cable, restart the system.
•
Do not unplug the LAN cable used by an USB device (ex: video display). Otherwise, the program
(MagicInfo) may stop.
Adjusting the LCD Display
•
To access other sources, press the SOURCE button in MagicInfo.
•
The preset password for the LCD Display is "000000".
•
The server program's Power-On option works only if the LCD Display's power is completely shut
off.
Please make sure not to use the Power-On option when the LCD Display is in the process of shutting
down since this may cause system errors on the LCD Display.
•
In the OSD image of MagicInfo, Network mode is the same as Device.
•
When using MagicInfo with the MagicInfo Pro Server Program: perform Network mode.
•
When using MagicInfo with the device directly connected to LCD Display : execute Device mode.
•
Press ALT + F12 to directly go to the MagicInfo Window screen.
•
To setup MagicInfo on a Windows screen, a keyboard and mouse are required.
•
To setup MagicInfo on a Windows screen, refer to the MagicInfo Pro Server Help.
It is highly recommended not to turn off the AC power during an operation.
•
For pivoted LCD Displays, ticker transparency is not supported.
•
For pivoted LCD Displays, a screen resolution of up to 720*480(SD) is supported for movies.
•
For drive D:, EWF is not applied.
•
When the contents of Setup have been changed when EWF is in the Enable state, to save the
changes in the disk, you must Commit them.
•
By selecting Disable, Enable or Commit, the system is restarted.
Photo
The JPEG, BMP file format are supported.
Auto
Adjusting the LCD Display
Automatically fits the image to the window.
Original
Shows the properties of the original file.
Slide Show
Displays the properties of the original file as they are.
Interval
Controls the time intervals between image files for a slide show. (5 Sec, 10 Sec, 20 Sec, 30 Sec, 60
Sec)
Adjusting the LCD Display
Rotation
Displays an image file by turning it clockwise by 90 degrees.
Zoom
Displays a reduced picture.
Adjusting the LCD Display
Close
Closes the image control Menu.
Music
The MP3 file format is supported.
Movie
The MPEG1, WMV file format are supported.
Adjusting the LCD Display
Play
Plays a movie file.
Full Size
Plays a movie file in full screen.
Adjusting the LCD Display
OFFICE / HTML
PPT(Power Point), DOC(MS Word), XLS(MS Excel), PDF, HTML, HTM files are displayed.
Note
•
Install the proper viewer(freeware) program to see the MS Office(Word, Excel, Power Point) or
PDF doucuments.
Internet
Connects to the Internet
Setup
Sets various functions in MagicInfo mode. A password must be entered to access Setup mode.
Adjusting the LCD Display
Schedule View
Displays a schedule.
TCP/IP
Changes the TCP/IP settings.
Adjusting the LCD Display
Connection
Modifies the network settings.
Password
The password can be changed.
•
The password should be between 6 and 12 characters in numeric format.
(You should enter a password between 6 and 12 characters in numeric format)
•
If you enter the wrong password three times, the setup configuration is reset and a warning message
appears from the server.
Adjusting the LCD Display
•
If you forget the password, enter Info, 8, 2 and 4 on the remote control to initialize the password.
This will reset the previous settings of Setup mode.
File
Local : You can delete or copy files on both local and removable disks.
Play Option
You can set the repeat play and screen settings.
Repeat : Determines the repeat option for playing movies and music.
•
None - Select No Repeat to play a movie or tune in the list only once.
Adjusting the LCD Display
•
File Repeat - Select Repeat File to play a movie or tune in the list repeatedly.
•
List Repeat - Select Repeat List to play movies or tunes in the list in sequence repeatedly.
Rotation - Sets the picture orientation.
•
Landscape - Sets the screen resolution to 1366x768 pixels.
•
Portrait - Sets the screen resolution to 768x1366 pixels.
EWF(Enhanced Write Filter) : Prevents change to and loss of the data saved on
the disk.
•
Disable - Disables EWF to allow saved data to be changed data on the protected disk (drive C:).
When switching from the Enable to the Disable state, you can select Commit.
•
Enable - Enables EWF to prevent saved data to be changed on the protected disk (drive C:).
•
Commit - Commit the changed data to the protected disk (drive C:) when EWF is in the Enable state. Commit is not available when EWF is in the Disable state.
Troubleshooting
Self-Test Feature Check
Note
Check the following items yourself before calling for assistance. Contact a Service Center for problems
that you cannot solve by yourself.
Self-Test Feature Check
1.
Turn off both your computer and the LCD Display.
2.
Unplug the video cable from the back of the computer.
3.
Turn on the LCD Display.
The figure shown below ("Check Signal Cable") appears on a black background when the LCD
Display is working normally even though no video signal is detected: While in the Self-Test mode,
the LED power indicator remains green and the figure moves around on the screen.
4.
Turn off your LCD Display and reconnect the video cable; then turn on both your computer and
the LCD Display
If your LCD Display screen remains blank after using the previous procedure, check your video controller and computer system; your LCD Display is functioning properly.
Warning Messages
You can even view the screen at a resolution of 1360 x 768. However, you will receive the following
message for a minute; You can choose to change the screen resolution or stay in the current mode
during that time. And if the resolution is more than 85Hz, you will see the black screen because the
LCD Display does not support over 85Hz.
Note
Refer to Specifications > Preset Timing Modes for the resolutions or frequencies supported by the
LCD Display.
Maintenance and Cleaning
1) Maintaining the LCD Display Case.
Clean with a soft cloth after disconnecting the power cord.
Troubleshooting
•
Do not use benzene, thinner or other flammable substances, or a wet cloth.
•
We recommend that a SAMSUNG cleansing agent is used
to prevent damage to the screen.
2) Maintaining the Flat Panel Display Screen.
Clean with a soft cloth (cotton flannel) smoothly.
•
Never use acetone, benzene or thinner.
(They may cause flaws or deformation of the screen surface.)
•
The user will be required to pay costs and related expenses
for repairing damages caused.
Symptoms and Recommended Actions
Note
A LCD Display recreates visual signals received from the computer. Therefore, if there is a problem
with the computer or the video card, this can cause the LCD Display to become blank, have poor
coloring, become noisy, and video mode not supported, etc. In this case, first check the source of the
problem, and then contact a Service Center or your dealer.
1.
Check if the power cord and the video cables are properly connected to the computer.
2.
Check if the computer beeps more than 3 times when booting.
(If it does, request an a service for the main board of the computer.)
3.
If you installed a new video card or if you assembled the PC, check if you installed the Adaptor
(video).
4.
Check if the scanning ratio of the video screen is set to between 50 Hz ~ 85 Hz.
(Do not exceed 60Hz when using the maximum resolution.)
5.
If you have problems in installing the Adaptor (video) driver, boot the computer in Safe Mode,
remove the Display Adaptor in the "Control Panel → System → Device Administrator" and then
reboot the computer to reinstall the Adaptor (video) driver.
Check List
Note
•
The following table lists possible problems and their solutions. Before calling for assistance, check
the information in this section to see if you can remedy any problems for yourself. If you do need
assistance, please call the phone number on the Information section or contact your dealer.
•
For more network-related information, refer to the MagicInfo Troubleshooting section.
Problems related to the Installation (PC Mode)
Note
Problems related to the LCD Display installation and their solutions are listed.
Q:
The LCD Display screen flickers.
Troubleshooting
A:
Check if the signal cable between the computer and the LCD Display is securely connected.
(Refer to Connecting a Computer)
Problems related to the Screen
Note
Problems related to the LCD Display screen and their solutions are listed.
Q:
The screen is blank and the power indicator is off.
A:
Ensure that the power cord is firmly connected and the LCD Display is on.
(Refer to the Connecting a Computer)
Q:
"Check Signal Cable" message.
A:
Ensure that the signal cable is firmly connected to the PC or video sources.
(Refer to the Connecting a Computer)
A:
Ensure that the PC or video sources are turned on.
Q:
"Not Optimum Mode" message.
A:
Check the maximum resolution and the frequency of the video Adaptor.
A:
Compare these values with the data in the Preset Timing Modes Chart.
Q:
The picture rolls vertically.
A:
Check if the signal cable is securely connected. Re-connect it, if necessary.
(Refer to Connecting a Computer)
Q:
The image is not clear; picture is blurred.
A:
Run Frequency Coarse and Fine tuning.
A:
Turn on again after removing all accessories (video extension cable, etc.)
A:
Set the resolution and frequency to the recommended ranges.
Q:
The picture image is unstable and shakes.
A:
Check if the resolution and frequency set for the computer video card falls in the range supported
by the LCD Display. If not, reset them referring to the current Information under the LCD Display
menu and Preset Timing Modes.
Q:
Ghost images are shown in the picture.
A:
Check if the resolution and frequency set for the computer video card falls in the range supported
by the LCD Display. If not, reset them referring to the current Information under the LCD Display
menu and Preset Timing Modes.
Q:
The image is too light or too dark.
A:
Adjusts the brightness and contrast.
(Refer to the Brightness, Contrast)
Q:
The screen color is inconsistent.
Troubleshooting
A:
Adjust color using Custom under OSD Color Adjustment menu.
Q:
The color image is distorted by dark shadows.
A:
Adjust color using Custom under OSD Color Adjustment menu.
Q:
The color white is poor.
A:
Adjust color using Custom under OSD Color Adjustment menu.
Q:
The power Indicator blinks green.
A:
The LCD Display is currently saving the changes made to the settings to the OSD memory.
Q:
The screen is blank and the power indicator light is steady green or blinks every 0.5 or 1 seconds.
A:
The LCD Display is using its power management system.
A:
Press a key on the keyboard.
Q:
The screen is blank and it is blinking.
A:
If you see the "TEST GOOD" message on the screen when you pressing the MENU button,
check the cable connection between the LCD Display and the computer to ensure that the connector is properly connected.
Problems related to Audio
Note
Problems related to audio signals and their solutions are listed below.
Q:
No sound.
A:
Ensure that the audio cable is firmly connected to both the audio-in port on your LCD Display
and the audio-out port on your sound card.
(Refer to the Connecting a Computer)
A:
Check the volume level.
Q:
The sound level is too low.
A:
Check the volume level.
A:
If the volume is still too low after turning the control to its maximum, check the volume control
on the computer sound card or software program.
Q:
The sound is too high or too low.
A:
Adjusts the Treble and Bass to the appropriate levels.
Problems related to the Remote Control
Note
Problems related to the remote control and their solutions are listed.
Q:
The remote control buttons do not respond.
A:
Check the polarities (+/-) of the batteries.
A:
Check if the batteries are empty.
Troubleshooting
A:
Check if the power is on.
A:
Check if the power cord is securely connected.
A:
Check if a special fluorescent or neon lamp is on in the vicinity.
Problems related to MagicInfo
Note
Making a Bootable USB Flash Disk.
Q:
Making a Bootable USB Flash Disk
A:
1) You can turn a common 512-MB or bigger USB storage media into a bootable disk using a
USB bootable disk creation tool. (For example, the HP USB Disk Storage Format Tool)
A:
2) Copies the OS ghost image and executables to your USB disk.
A:
3) Enter the BIOS menu of your set by pressing the F2 key in the BIOS logo screen. Then, enable
the USB Boot First option by selecting that option and pressing the Enter key in the Boot menu.
A:
4) Switch your set on while your USB disk is connected and boot up in DOS mode.
A:
5) Run C:\ghost.exe and choose Local → Partition → From Image from the menu. Choose the
ghost image to update your USB disk with and choose the target disk.
A:
6) When the ghost image update finishes, the set will be rebooted automatically.
Q:
How can I change the frequency?
A:
The frequency can be changed by reconfiguring the video card.
Q&A
Note
that video card support can vary, depending on the version of the driver used. (Refer to the
computer or the video card manual for details.)
Q:
How can I Adjusts the resolution?
A:
Windows XP:
Set the resolution in the Control Panel → Appearance and Themes → Display → Settings.
A:
Windows ME/2000:
Set the resolution in the Control Panel → Display → Settings.
* Contact the video card manufacturer for details.
Q:
How can I set the Power Saving function?
A:
Windows XP:
Set the resolution in the Control Panel → Appearance and Themes → Display → Screen Saver.
Set the function in the BIOS-SETUP of the computer. (Refer to the Windows / Computer Manual).
A:
Windows ME/2000:
Troubleshooting
Set the resolution at the Control Panel → Display → Screen Saver.
Set the function in the BIOS-SETUP of the computer. (Refer to the Windows / Computer Manual).
Q:
How can I clean the outer case/LCD Panel?
A:
Disconnect the power cord and then clean the LCD Display with a soft cloth, using either a
cleaning solution or plain water.
Do not leave any detergent or scratches on the case. Do not let any water enter the LCD Display.
Q:
How can I play the video?
A:
The video supports the MPEG1 and WMV codecs only. Install the corresponding codec to play
the video. Note that some of the codecs can be incompatible.
Note
Before calling for assistance, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the Information section or
contact your dealer.
Specifications
General
General
Model Name
SyncMaster 400UXn
LCD Panel
Size
40 " Diagonal (101 cm)
Display area
885.168 mm (H) X 497.664 mm (V)
Pixel Pitch
0.648 mm (H) X 0.648 mm (V)
Synchronization
Horizontal
30 ~ 81 kHz
Vertical
56 ~ 85 Hz
Display Color
16.7 M
Resolution
Optimum resolution
1360 x 768 @ 60 Hz depends on graphics card used
Maximum resolution
1360 x 768 @ 60 Hz
Input Signal, Terminated
RGB Analog, DVI Compliant Digital RGB
0.7 Vp-p ±5 %
Separate H/V sync, Composite, SOG(Option)
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
140MHz (Analog,Digital)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin-to-15pin D-sub cable, Detachable
DVI-D to DVI-D connector, Detachable (Sold separately)
Dimensions (W x H x D) / Weight
914 x 118 x 526 mm / 35.9 x 4.6 x 20.7 inch (Without Stand)
914 x 311 x 585 mm / 35.9 x 12.2 x 23.0 inch (With Stand) / 22.5 kg / 49.6 lbs
VESA Mounting Interface
600 x 400 mm
Specifications
Environmental considerations
Operating
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Humidity : 10 % ~ 80 %, non-condensing
Storage
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Humidity : 5 % ~ 95 %, non-condensing
Audio Characteristics
Audio Input 1
RCA Jack Red(R) White(L), 0.5 Vrms (-9 dB)
Audio Input 2
RCA Jack Red(R) White(L), 0.5 Vrms (-9 dB)
PC Audio Input
3.5 øStereo Jack, 0.5 Vrms (-9 dB)
Frequency
RF: 80 Hz ~ 15 kHz (at -3 dB)
Response
A/V: 80 Hz ~ 20 kHz (at -3 dB)
Plug and Play Capability
This LCD Display can be installed on any Plug & Play compatible system. The interaction
of the LCD Display and the computer systems will provide the best operating conditions
and LCD Display settings. In most cases, the LCD Display installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above are used for this product. But the pixels of RED,
GREEN, BLUE and WHITE color appear to be bright sometimes or some black pixels may
be seen. This is not from bad quality and you can use it without any problems.
For example, the number of TFT-LCD sub pixels contained in this product are 3,133,440.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can
be used in all areas including common residential areas. (Class B equipment emits less electromagnetic
waves than Class A equipment.)
MagicInfo - Client
Item
Contents
Specification
Remarks
LAN
1 Gbps
USB
Keyboard/Mouse, Mass Stor- USB removable storage can be
age Device Compatible
supported.
Photo
Supported File Format : BMP/
JPEG
Music
Supported File Format : MP3 Sound bandwidth : 50 Hz to 15
kHz
Movie
- MPEG1, WMV
- Max 1280 x 720 30 fps
2274x1704 or less
Specifications
Item
Specification
File
Remarks
MS Office(Word, Excel, - Some files may not be supporPower Point), HTML, PDF ted depending on the format or
the version.
- Install the proper viewing
(freeware) program to see MS
Office (Word, Excel, Power
Point) or PDF documents.
Internet Browser
MS Internet Explorer
Language
English
OS
Windows XP Embedded
Not Support Flash, Java Applet,
Security Site
MagicInfo Pro - Server Requirement
CPU
RAM
Ethernet OS
Application
Minimum
P1.8 Ghz 256 M
100 M / 1 Windows WMP 9 or latG
XP
er
Recommended
P3.0 Ghz 512 M
100 M / 1 Windows WMP 9 or latG
XP
er
PowerSaver
This LCD Display has a built-in power management system called PowerSaver. This system saves
energy by switching your LCD Display to low-power mode when it has not been used for a certain
amount of time. The LCD Display automatically returns to normal operation when you press a key on
the keyboard. For energy conservation, turn your LCD Display OFF when it is not needed, or when
leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant
video card installed in your computer. Use the software utility installed on your computer to set up this
feature.
PowerSaver (When used as a Network monitor)
State
Normal Operation Power saving mode
Power off
EPA/ENERGY 2000
Power Indicator
Green
Green, Blinking
Amber
Power Consumption
280 W
Less than1watts
1 watts
PowerSaver (When used as a normal monitor)
State
Normal Operation Power saving mode
Power off
EPA/ENERGY 2000
Power Indicator
Green
Green, Blinking
Amber
Power Consumption
220 W
Less than1watts
1 watts
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the
screen will be adjusted automatically. However, if the signal differs, the screen may go blank while
the power LED is on. Refer to the video card manual and adjusts the screen as follows.
Specifications
Display Mode
Horizontal
Frequency
(kHz)
Vertical Frequency (Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
IBM, 640 x 350
31.469
70.086
25.175
+/-
IBM, 640 x 480
31.469
59.940
25.175
-/-
IBM, 720 x 400
31.469
70.087
28.322
-/+
MAC, 640 x 480
35.000
66.667
30.240
-/-
MAC, 832 x 624
49.726
74.551
57.284
-/-
MAC, 1152 x 870
68.681
75.062
100.000
-/-
VESA, 640 x 480
37.861
72.809
31.500
-/-
VESA, 640 x 480
37.500
75.000
31.500
-/-
VESA, 800 x 600
35.156
56.250
36.000
+/+
VESA, 800 x 600
37.879
60.317
40.000
+/+
VESA, 800 x 600
48.077
72.188
50.000
+/+
VESA, 800 x 600
46.875
75.000
49.500
+/+
VESA, 1024 x 768
48.363
60.004
65.000
-/-
VESA, 1024 x 768
56.476
70.069
75.000
-/-
VESA, 1024 x 768
60.023
75.029
78.750
+/+
VESA, 1152 x 864
67.500
75.000
108.000
+/+
VESA, 1280 X 960
60.000
60.000
108.000
+/+
VESA, 1280 X 1024
63.981
60.020
108.000
+/+
VESA, 1280 X 1024
79.976
75.025
135.000
+/+
VESA, 1360 x 768
47.712
60.015
85.500
+/+
Horizontal Frequency
The time to scan one line connecting the right edge to the
left edge of the screen horizontally is called the Horizontal
Cycle and the inverse number of the Horizontal Cycle is
called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same
image many times per second to display an image to the
user. The frequency of this repetition is called the Vertical
Frequency or Refresh Rate. Unit: Hz
General
General
Model Name
SyncMaster 460UXn
LCD Panel
Size
46 " Diagonal (116 cm)
Display area
1018.353 mm (H) x 572.544 mm (V)
Pixel Pitch
0.7455 mm (H) x 0.7455 mm (V)
Specifications
Synchronization
Horizontal
30 ~ 81 kHz
Vertical
56 ~ 85 Hz
Display Color
16.7 M
Resolution
Optimum resolution
1360 x 768 @ 60 Hz depends on graphics card used
Maximum resolution
1360 x 768 @ 60 Hz
Input Signal, Terminated
RGB Analog, DVI Compliant Digital RGB
0.7 Vp-p ±5 %
Separate H/V sync, Composite, SOG(Option)
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
140MHz (Analog,Digital)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal Cable
15pin-to-15pin D-sub cable, Detachable
DVI-D to DVI-D connector, Detachable (Sold separately)
Dimensions (W x H x D) / Weight
1049 x 118 x 603 mm / 41.2 x 4.6 x 23.7 inch (Without Stand)
1049 x 311 x 662 mm / 41.2 x 12.2 x 26.0 inch (With Stand) / 29 kg / 63.9 lbs
VESA Mounting Interface
600 x 400 mm
Environmental considerations
Operating
Temperature : 50°F ~ 104°F (10°C ~ 40°C)
Humidity : 10 % ~ 80 %, non-condensing
Storage
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Humidity : 5 % ~ 95 %, non-condensing
Audio Characteristics
Audio Input 1
RCA Jack Red(R) White(L), 0.5 Vrms (-9 dB)
Audio Input 2
RCA Jack Red(R) White(L), 0.5 Vrms (-9 dB)
PC Audio Input
3.5 øStereo Jack, 0.5 Vrms (-9 dB)
Specifications
Audio Characteristics
Frequency
RF: 80 Hz ~ 15 kHz (at -3 dB)
Response
A/V: 80 Hz ~ 20 kHz (at -3 dB)
Plug and Play Capability
This LCD Display can be installed on any Plug & Play compatible system. The interaction
of the LCD Display and the computer systems will provide the best operating conditions
and LCD Display settings. In most cases, the LCD Display installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above are used for this product. But the pixels of RED,
GREEN, BLUE and WHITE color appear to be bright sometimes or some black pixels may
be seen. This is not from bad quality and you can use it without any problems.
For example, the number of TFT-LCD sub pixels contained in this product are 3,133,440.
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use and can
be used in all areas including common residential areas. (Class B equipment emits less electromagnetic
waves than Class A equipment.)
MagicInfo - Client
Item
Specification
Remarks
LAN
1 Gbps
USB
Keyboard/Mouse, Mass Stor- USB removable storage can be
age Device Compatible
supported.
Contents
Photo
Supported File Format : BMP/
JPEG
Music
Supported File Format : MP3 Sound bandwidth : 50 Hz to 15
kHz
Movie
2274x1704 or less
- MPEG1, WMV
- Max 1280 x 720 30 fps
File
MS Office(Word, Excel, - Some files may not be supporPower Point), HTML, PDF ted depending on the format or
the version.
- Install the proper viewing
(freeware) program to see MS
Office (Word, Excel, Power
Point) or PDF documents.
Internet Browser
MS Internet Explorer
Language
English
OS
Windows XP Embedded
Not Support Flash, Java Applet,
Security Site
Specifications
MagicInfo Pro - Server Requirement
CPU
RAM
Ethernet OS
Application
Minimum
P1.8 Ghz 256 M
100 M / 1 Windows WMP 9 or latG
XP
er
Recommended
P3.0 Ghz 512 M
100 M / 1 Windows WMP 9 or latG
XP
er
PowerSaver
This LCD Display has a built-in power management system called PowerSaver. This system saves
energy by switching your LCD Display to low-power mode when it has not been used for a certain
amount of time. The LCD Display automatically returns to normal operation when you press a key on
the keyboard. For energy conservation, turn your LCD Display OFF when it is not needed, or when
leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant
video card installed in your computer. Use the software utility installed on your computer to set up this
feature.
PowerSaver (When used as a Network monitor)
State
Normal Operation Power saving mode
Power off
EPA/ENERGY 2000
Power Indicator
Green
Green, Blinking
Amber
Power Consumption
330 W
Less than1watts
1 watts
PowerSaver (When used as a normal monitor)
State
Normal Operation Power saving mode
Power off
EPA/ENERGY 2000
Power Indicator
Green
Green, Blinking
Amber
Power Consumption
270 W
Less than1watts
1 watts
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the
screen will be adjusted automatically. However, if the signal differs, the screen may go blank while
the power LED is on. Refer to the video card manual and adjusts the screen as follows.
Display Mode
Horizontal
Frequency
(kHz)
Vertical Frequency (Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
IBM, 640 x 350
31.469
70.086
25.175
+/-
IBM, 640 x 480
31.469
59.940
25.175
-/-
IBM, 720 x 400
31.469
70.087
28.322
-/+
MAC, 640 x 480
35.000
66.667
30.240
-/-
MAC, 832 x 624
49.726
74.551
57.284
-/-
MAC, 1152 x 870
68.681
75.062
100.000
-/-
VESA, 640 x 480
37.861
72.809
31.500
-/-
Specifications
Display Mode
Horizontal
Frequency
(kHz)
Vertical Frequency (Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
VESA, 640 x 480
37.500
75.000
31.500
-/-
VESA, 800 x 600
35.156
56.250
36.000
+/+
VESA, 800 x 600
37.879
60.317
40.000
+/+
VESA, 800 x 600
48.077
72.188
50.000
+/+
VESA, 800 x 600
46.875
75.000
49.500
+/+
VESA, 1024 x 768
48.363
60.004
65.000
-/-
VESA, 1024 x 768
56.476
70.069
75.000
-/-
VESA, 1024 x 768
60.023
75.029
78.750
+/+
VESA, 1152 x 864
67.500
75.000
108.000
+/+
VESA, 1280 X 960
60.000
60.000
108.000
+/+
VESA, 1280 X 1024
63.981
60.020
108.000
+/+
VESA, 1280 X 1024
79.976
75.025
135.000
+/+
VESA, 1360 x 768
47.712
60.015
85.500
+/+
Horizontal Frequency
The time to scan one line connecting the right edge to the
left edge of the screen horizontally is called the Horizontal
Cycle and the inverse number of the Horizontal Cycle is
called the Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same
image many times per second to display an image to the
user. The frequency of this repetition is called the Vertical
Frequency or Refresh Rate. Unit: Hz
Information
For Better Display
Adjust the computer resolution and screen injection rate (refresh rate) on the computer
as described below to enjoy the best picture quality. You can have an uneven picture quality
on screen if the best picture quality is not provided for TFT-LCD.
•
Resolution: 1360 x 768
•
Vertical frequency (refresh rate): 60 Hz
TFT-LCD panels manufactured by using advanced semiconductor technology with a
precision of 1ppm (one millionth) and above is used for this product. But the pixels of RED,
GREEN, BLUE and WHITE color seem to be bright sometimes or some of black pixels
could be seen. This is not from bad quality and you can use it without any problems.
•
For example, the number of TFT-LCD sub pixels contained in this product are
3,133,440.
When cleaning the monitor and the panel outside, please apply the recommended small
amount of cleaner by using a soft cloth to polish. Do not force the LCD area but rub softly.
If excessive force is applied, you may stain it.
If you are not satisfied with the picture quality, you can get better quality of picture by
performing the "Auto Adjustment function" in display screen that is appeared as window
termination button is pressed. If there's still noise after the automatic adjustment, use the
Fine/Coarse adjustment function.
When viewing a fixed screen for an extended period of time, a residual image or blurriness may appear. Change the mode to energy save or set a screensaver to move the picture
when you need to be away from the monitor for an extended period of time.
PRODUCT INFORMATION (Image Retention Free)
What is Image Retention ?
Image retention may not occur when a LCD panel is operated under normal conditions.
Normal conditions are defined as continuously changing video patterns. When the LCD
panel is operated for a long time with a fixed pattern (over 12 hours), there may be slight
difference in voltage between electrodes that work the liquid crystal (LC) in a pixel. The
voltage difference between electrodes increases with time, forcing the liquid crystal to lean.
When this occurs, the previous image may be seen when the pattern is changed. To prevent
this, the accumulated voltage difference must be decreased.
Information
Power Off, Screen Saver, or Power Save Mode
•
Turn the power off for 4 hours after 20 hours in use
•
Turn the power off for 2 hours after 12 hours in use
•
Set the Monitor to power off with the PC Display Properties Power Scheme.
•
Use a Screen saver if possible - Screen saver in one color or a moving image is recommended.
Change the Color Information periodically
Note
Use Two different colors
Rotate the Color Information with 2 different colors every 30 minutes.
Information
•
Avoid using a combination of characters and background color with large difference in
luminance.
Avoid using Grey colors, which can cause Image retention easily.
Avoid: Colors with big difference in luminance (Black & White, Grey)
Change the characters color periodically
•
Use Bright colors with little difference in luminance.
- Cycle : Change the characters color and background color every 30 minutes
•
Every 30 minutes, change the characters with movement.
•
All area display Moving image together with Logo periodically.
- Cycle: Display moving image together with Logo for 60 seconds after 4 hours in use.
•
The best way to protect your monitor from Image retention is to turn Power off, or set
your PC, or System to operate a Screen Saver program when you are not using it. Also
Warranty service will be limited based on instruction guide.
Apply the Screen Scroll function on Product
•
Apply the Screen Scroll function
- Symptom: Horizontal Bar with Black Color move up and down.
- Select method
•
Instruction Guide : OSD Menu -> Set Up -> Safety Screen -> Screen Scroll
•
Time Interval : 1 ~ 10 hours ( Recommend : 1 )
•
Time Period : 1 ~ 5 second ( Recommend : 5 )
Information
Note
( Please check CD's User Guide at "OSD Function", some model's will not available )
Apply the Screen Pixel function on Product
•
Apply the Screen Pixel function
- Symptom: Dot with Black Color move up and down.
- Select method
•
•
Instruction Guide : OSD Menu -> Set Up -> Safety Screen -> Pixel
•
Time Interval : 1 ~ 10 hours ( Recommend : 1 )
•
Time Period : 10 ~ 50 second ( Recommend : 50 )
Apply the Screen Bar function
- Symptom: Horizontal / Vertical Bar with Black Color move up and down.
- Select method
•
Instruction Guide : OSD Menu -> Set Up -> Safety Screen -> Bar
•
Time Interval : 1 ~ 10 hours ( Recommend : 1 )
•
Time Period : 10 ~ 50 second ( Recommend : 50 )
Note
( Please check CD's User Guide at "OSD Function", some model's will not available. )
Apply the Screen Erasing function on Product
•
Apply the Screen Erasing function
- Symptom: 2 Vertical blocks move with erasing the display
Information
- Select method
•
Instruction Guide : OSD Menu -> Set Up -> Safety Screen -> Eraser
•
Time Interval : 1 ~ 10 hours ( Recommend : 1 )
•
Time Period : 10 ~ 50 second ( Recommend : 50 )
Note
( Please check CD's User Guide at "OSD Function", some model's will not available )
Appendix
Contact SAMSUNG WORLDWIDE
Note
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG
customer care center.
North America
U.S.A
1-800-SAMSUNG(726-7864)
http://www.samsung.com
CANADA
1-800-SAMSUNG(726-7864)
http://www.samsung.com/ca
MEXICO
01-800-SAMSUNG(726-7864) http://www.samsung.com
Latin America
ARGENTINE
0800-333-3733
http://www.samsung.com/ar
BRAZIL
0800-124-421
http://www.samsung.com
4004-0000
CHILE
800-SAMSUNG(726-7864)
http://www.samsung.com/cl
COLOMBIA
01-8000112112
http://www.samsung.com/co
COSTA RICA
0-800-507-7267
http://www.samsung.com/latin
ECUADOR
1-800-10-7267
http://www.samsung.com/latin
EL SALVADOR
800-6225
http://www.samsung.com/latin
GUATEMALA
1-800-299-0013
http://www.samsung.com/latin
HONDURAS
800-7919267
JAMAICA
1-800-234-7267
NICARAGUA
00-1800-5077267
PANAMA
800-7267
http://www.samsung.com/latin
PUERTO RICO
1-800-682-3180
http://www.samsung.com/latin
REP. DOMINICA
1-800-751-2676
http://www.samsung.com/latin
http://www.samsung.com/latin
TRINIDAD & TO- 1-800-SAMSUNG(726-7864)
BAGO
http://www.samsung.com/latin
VENEZUELA
http://www.samsung.com/latin
0-800-100-5303
Europe
AUSTRIA
0800-SAMSUNG (726-7864)
http://www.samsung.com/at
BELGIUM
0032 (0)2 201 24 18
http://www.samsung.com/be
CZECH REPUBLIC 844 000 844
http://www.samsung.com/cz
DENMARK
70 70 19 70
http://www.samsung.com/dk
EIRE
0818 717 100
http://www.samsung.com/ie
FINLAND
030-6227 515
http://www.samsung.com/fi
FRANCE
3260 SAMSUNG (€ 0,15/Min) http://www.samsung.com
08 25 08 65 65 (€ 0,15/Min)
Appendix
Europe
GERMANY
01805 - SAMSUNG (726-7864) http://www.samsung.com
(€ 0,14/Min)
HUNGARY
06-80-SAMSUNG (726-7864)
http://www.samsung.com
ITALIA
800-SAMSUNG (726-7864)
http://www.samsung.com
LUXEMBURG
0035 (0)2 261 03 710
http://www.samsung.com/be
NETHERLANDS
0900 SAMSUNG (726-7864 € http://www.samsung.com/nl
0,10/Min)
NORWAY
815-56 480
http://www.samsung.com/no
POLAND
0 801 801 881
http://www.samsung.com/pl
022-607-93-33
PORTUGAL
80820-SAMSUNG (726-7864)
http://www.samsung.com/pt
SLOVAKIA
0800-SAMSUNG (726-7864)
http://www.samsung.com/sk
SPAIN
902 10 11 30
http://www.samsung.com
SWEDEN
0771-400 200
http://www.samsung.com/se
SWITZERLAND
0800-SAMSUNG (726-7864)
http://www.samsung.com/ch
U.K
0845 SAMSUNG (7267864)
http://www.samsung.com
CIS
ESTONIA
800-7267
http://www.samsung.ee
LATVIA
800-7267
http://www.samsung.com/lv
LITHUANIA
8-800-77777
http://www.samsung.lt
KAZAKHSTAN
8-10-800-500-55-500
http://www.samsung.kz
KYRGYZSTAN
00-800-500-55-500
RUSSIA
8-800-555-55-55
TADJIKISTAN
8-10-800-500-55-500
UKRAINE
8-800-502-0000
http://www.samsung.com
UZBEKISTAN
8-10-800-500-55-500
http://www.samsung.uz
http://www.samsung.ru
Asia Pacific
AUSTRALIA
1300 362 603
http://www.samsung.com
CHINA
800-810-5858
http://www.samsung.com
010-6475 1880
HONG KONG
3698 - 4698
http://www.samsung.com/hk
INDIA
3030 8282
http://www.samsung.com
1800 110011
INDONESIA
0800-112-8888
http://www.samsung.com
JAPAN
0120-327-527
http://www.samsung.com/jp
MALAYSIA
1800-88-9999
http://www.samsung.com/my
NEW ZEALAND
0800 SAMSUNG(726-7864)
http://www.samsung.com/nz
PHILIPPINES
1800-10-SAMSUNG(726-7864) http://www.samsung.com/ph
SINGAPORE
1800-SAMSUNG(726-7864)
http://www.samsung.com
THAILAND
1800-29-3232, 02-689-3232
http://www.samsung.com
Appendix
Asia Pacific
TAIWAN
0800-329-999
http://www.samsung.com/tw
VIETNAM
1 800 588 889
http://www.samsung.com
Middle East & Africa
SOUTH AFRICA
0860-SAMSUNG(726-7864)
http://www.samsung.com
TURKEY
444 77 11
http://www.samsung.com
U.A.E
800-SAMSUNG(726-7864)
http://www.samsung.com
8000-4726
Terms
Dot Pitch
The image on a monitor is composed of red, green and blue dots.
The closer the dots, the higher the resolution. The distance between two dots of the same color is called the 'Dot Pitch'. Unit:
mm
Vertical Frequency
The screen must be redrawn several times per second in order to
create and display an image for the user. The frequency of this
repetition per second is called the Vertical Frequency or Refresh
Rate. Unit: Hz
Example: If the same light repeats itself 60 times per second, this
is regarded as 60 Hz.
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge
of the screen horizontally is called the Horizontal Cycle. The inverse number of the Horizontal Cycle is called Horizontal Frequency. Unit: kHz
Interlace
Methods
Showing the horizontal lines of the screen from the top to the bottom sequentially is called the Non-Interlace method while showing odd lines and then even lines in turn is called the Interlace
method. The Non-Interlace method is used for the majority of
monitors to ensure a clear image. The Interlace method is the same
as that used in TVs.
and
Non-Interlace
Plug & Play
This is a function that provides the best quality screen for the user
by allowing the computer and the monitor to exchange information automatically. This monitor follows the international standard
VESA DDC for the Plug & Play function.
Resolution
The number of horizontal and vertical dots used to compose the
screen image is called the 'resolution'. This number shows the accuracy of the display. A high resolution is good for performing
multiple tasks as more image information can be shown on the
screen.
Example: If the resolution is 1360 x 768, this means the screen is
composed of 1360 horizontal dots (horizontal resolution) and 768
vertical lines (vertical resolution).
Appendix
Correct Disposal
Correct Disposal of This Product (Waste Electrical & Electronic Equipment) Europe only
(Applicable in the European Union and other European
countries with separate collection systems)
This marking shown on the product or its literature, indicates that it should not be disposed with other household
wastes at the end of its working life. To prevent possible
harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of
wastes and recycle it responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where
they purchased this product, or their local government office, for details of where and how they can take this item
for environmentally safe recycling.
Business users should contact their supplier and check the
terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for
disposal.
Authority
Information in this document is subject to change without notice.
© 2008 Samsung Electronics Co., Ltd. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co.,
Ltd. is strictly forbidden.
Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
Samsung is the registered trademark of Samsung Electronics Co., Ltd.; Microsoft, Windows and Windows NT are registered trademarks of Microsoft Corporation; VESA, DPM and DDC are registered
trademarks of Video Electronics Standard Association; the ENERGY STAR® name and logo are registered trademarks of the U.S. Environmental Protection Agency (EPA). All other product names
mentioned herein may be the trademarks or registered trademarks of their respective owners.
Download PDF