Samsung | RM48D | Samsung SMART Signage TV RM48D Benutzerhandbuch

SMART Signage TV
User Manual
RM40D RM48D
The colour and the appearance may differ depending on the product, and
the specifications are subject to change without prior notice to improve the
performance.
Recommended hours of use per day of this product is under 16 hours.
If the product is used for longer than 16 hours a day, the warranty may be void.
BN46-00492C-00
Table of contents
Before Using the Product
Copyright6
Safety Precautions
7
Symbols7
Cleaning7
Storage8
Electricity and Safety
8
Installation9
Operation11
Preparations
Checking the Components
15
Parts17
Control Panel
17
Reverse Side
19
Anti-theft Lock
20
Remote Control
21
Before Installing the Product
(Installation Guide)
23
Tilting Angle and Rotation
23
Ventilation23
Connecting and Using a Source
Device
If the input source is TV, HDMI1, HDMI2 or AV34
Before Connecting
Pre-connection Checkpoints
27
27
Connecting to a PC
Connection using the D-SUB cable
(Analogue type)
Connection Using an HDMI Cable
Connection Using an HDMI-DVI Cable
27
Connecting to a Video Device
Connection Using the AV Cable
Connection Using an HDMI-DVI Cable
Connection Using an HDMI Cable
29
29
30
30
Connecting to an Audio System
31
Connecting the Antenna
31
Connecting to a TV Viewing Card slot
To connect the CI CARD, follow these steps:
32
32
Initial Setup
33
27
28
28
Changing the Input source
33
Source List33
Dimensions24
Installing the Wall Mount
Installing the Wall Mount Kit
Wall Mount Kit Specifications
25
25
26
Screen Adjustment
Picture Mode34
If the input source is PC or HDMI1 (when a PC
is connected), HDMI2 (when a PC is connected) 34
Backlight / Contrast / Brightness /
Sharpness / Colour / Tint (G/R)35
Picture Size36
Picture Size36
Position38
Zoom/Position38
4:3 Screen Size39
Resolution Select39
Auto Adjustment40
PC Screen Adjustment41
PIP42
PIP Settings
42
Advanced Settings43
Dynamic Contrast44
Black Tone44
Flesh Tone44
RGB Only Mode44
Colour Space44
White Balance45
Gamma45
Motion Lighting45
Picture Options46
Colour Tone47
Colour Temp.47
Digital Clean View47
MPEG Noise Filter47
HDMI Black Level48
Film Mode48
2
Table of contents
Dynamic Backlight48
Schedule Manager61
Picture Off49
Edit Channel62
Reset Picture49
Edit Favorites64
Sound Adjustment
Channel Settings67
Country (Area)67
Manual Tuning67
Fine Tune68
Transfer Channel List68
Delete CAM Operator Profile68
Sound Mode50
Sound Effect51
Speaker Settings52
Additional Settings53
DTV Audio Level53
Dolby Digital Comp53
Reset Sound54
Broadcasting
Auto Tuning55
Auto Tuning55
Cable Search Option56
Aerial57
Channel List58
Sorting58
Mode58
Guide60
Subtitle69
Subtitle69
Primary Subtitle69
Secondary Subtitle69
Audio Options70
Audio Language70
Audio Format70
Audio Description70
Programme Rating Lock71
Digital Text72
Digital Text72
Teletext Language73
Teletext Language73
Primary Teletext73
Secondary Teletext73
Channel Lock75
Network
Network Status76
Network Settings76
Network Setting (Wireless)
77
WPS(PBC)79
Soft AP (Wi-Fi Hotspot)80
Wi-Fi Direct81
AllShare Settings82
Device Name82
Applications
Source List83
MagicInfo84
Playing content from the internal
memory or USB
84
Playing PC or mobile content
84
Schedule85
Common Interface74
CI Menu74
CAM video transcoding74
Application Info74
3
Table of contents
MagicInfo Express
Using MagicInfo Express
Managing templates
Managing schedules
System
87
87
87
Playing photos, videos and music
(Media Play)
Read the following before
using media play with a USB device
Using a USB device
Menu items in the media content list page
88
90
91
Available buttons and features
during photo playback
92
Available buttons and features
during video playback
Available buttons and features
during music playback
93
94
Supported Subtitle and
Media play file formats
95
Subtitle95
Compatible image file format
95
Supported music file formats
96
Supported Video Formats
96
Setup99
Initial settings (Setup)99
Menu Language101
Time102
Clock102
On Timer103
Off Timer105
Holiday Management105
MagicInfo On/Off Timer106
Eco Solution107
Energy Saving107
Eco Sensor107
No Signal Power Off108
Auto Power Off108
Auto Protection Time109
Screen Burn Protection110
Pixel Shift110
Timer111
Immediate display113
Side Grey113
Auto Power116
Safety Lock116
Button Lock117
USB Auto Play Lock117
Standby Control117
Lamp Schedule118
OSD Display118
Change PIN119
Clone Product120
Reset System120
Reset All121
DivX® Video On Demand121
Support
Software Update122
Update now122
Use Mode122
Contact Samsung123
Ticker114
Ticker114
Source AutoSwitch Settings115
Source AutoSwitch115
General116
Game Mode116
4
Table of contents
Troubleshooting Guide
Appendix
Requirements Before Contacting Samsung
Customer Service Centre
124
Testing the Product
124
Checking the Resolution and Frequency
124
Check the followings.
125
Contact SAMSUNG WORLD WIDE
Q & A
131
138
Responsibility for the Pay Service
(Cost to Customers)
147
Not a product defect
147
A Product damage caused by customer's fault 147
Others147
WEEE148
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
148
Correct disposal of batteries in this product
148
Specifications
General133
Power Consumption
135
Preset Timing Modes
136
Optimum Picture Quality and
Afterimage Burn-in Prevention
Optimum Picture Quality
Prevention of Afterimage Burn-in
149
149
149
Licence151
Terminology152
5
Chapter 01
Before Using the Product
Copyright
The contents of this manual are subject to change without notice to improve quality.
© 2014 Samsung Electronics
Samsung Electronics owns the copyright for this manual.
Use or reproduction of this manual in parts or entirety without the authorization of Samsung Electronics is prohibited.
Microsoft, Windows are registered trademarks of Microsoft Corporation.
VESA, DPM and DDC are registered trademarks of the Video Electronics Standards Association.
Ownership of all other trademarks is attributed to their due owner.
•• An administration fee may be charged if either
-- (a) an engineer is called out at your request and there is no defect in the product
(i.e. where you have failed to read this user manual).
-- (b) you bring the unit to a repair centre and there is no defect in the product
(i.e. where you have failed to read this user manual).
•• The amount of such administration charge will be advised to you before any work or home visit is carried out.
6
Safety Precautions
Cleaning
――Exercise care when cleaning as the panel and exterior of advanced LCDs are easily scratched.
Caution
――Take the following steps when cleaning.
――The following images are for reference only. Real-life situations may differ from what is shown in the
images.
RISK OF ELECTRIC SHOCK DO NOT OPEN
Caution : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. (OR BACK)
THERE ARE NO USER SERVICEABLE PARTS INSIDE.
REFER ALL SERVICING TO QUALIFIED PERSONNEL.
1
Power off the product and computer.
2
Disconnect the power cord from the product.
――Hold the power cable by the plug and do not touch the cable with wet
hands. Otherwise, an electric shock may result.
This symbol indicates that high voltage is present inside.
3
It is dangerous to make any kind of contact with any internal part of this product.
Wipe the product with a clean, soft and dry cloth.
•• Do not use detergents that contain alcohol, solvent or
surface-active agents.
This symbol alerts you that important literature concerning operation and maintenance has been
included with this product.
!
•• Do not spray water or detergent directly on the product.
Symbols
Warning
A serious or fatal injury may result if instructions are not followed.
4
Wet a soft and dry cloth in water and wring thoroughly to clean the
exterior of the product.
Caution
Personal injury or damage to properties may result if instructions are not followed.
Activities marked by this symbol are prohibited.
5
Connect the power cord to the product when cleaning is finished.
6
Power on the product and computer.
Instructions marked by this symbol must be followed.
7
Storage
Connect the power plug to a grounded power socket (type 1 insulated
devices only).
Due to the characteristics of high-glossy products, using a UV humidifier nearby may create whitecoloured stains on the product.
――Contact Customer Service Centre if the inside of the product needs cleaning (service fee will be
•• An electric shock or injury may result.
!
Do not bend or pull the power cord with force. Be careful not to leave the
power cord under a heavy object.
charged).
Electricity and Safety
•• Damage to the cord may result in a fire or electric shock.
――The following images are for reference only. Real-life situations may differ from what is shown in the
images.
Do not place the power cord or product near heat sources.
•• A fire or electric shock may result.
Warning
Do not use a damaged power cord or plug, or a loose power socket.
•• An electric shock or fire may result.
Clean any dust around the pins of the power plug or the power socket with
a dry cloth.
•• A fire may result.
Do not use multiple products with a single power socket.
•• Overheated power sockets may cause a fire.
!
Do not touch the power plug with wet hands. Otherwise, an electric shock
may result.
Insert the power plug all the way in so it is not loose.
•• An unsecure connection may cause a fire.
!
8
Installation
Caution
Do not disconnect the power cord while the product is being used.
•• The product may become damaged by an electric shock.
Warning
DO NOT PLACE CANDLES, INSECT REPELLANTS OR CIGARETTES ON TOP OF
THE PRODUCT. DO NOT INSTALL THE PRODUCT NEAR HEAT SOURCES.
•• A fire may result.
Only use the power cord provided with your product by Samsung. Do not
use the power cord with other products.
•• A fire or electric shock may result.
Have a technician install the wall-mount hanger.
!
•• Installation by an unqualified person can result in an injury.
•• Only use approved cabinets.
Keep the power socket where the power cord is connected unobstructed.
•• The power cord must be disconnected to cut off power to the product
when an issue occurs.
!
!
Do not install the product in poorly ventilated spaces such as a bookcase or
closet.
•• Note that the product is not completely powered down by using only
the power button on the remote.
•• An increased internal temperature may cause a fire.
Hold the plug when disconnecting the power cord from the power socket.
•• An electric shock or fire may result.
Install the product at least 10 cm away from the wall to allow ventilation.
•• An increased internal temperature may cause a fire.
!
!
Keep the plastic packaging out of the reach of children.
•• Children may suffocate.
!
9
Bend and keep part of the outdoor TV antenna cable hanging downwards
(the part inside the room) to prevent rainwater from entering the product.
Edible oil, such as soybean oil, can damage or deform the product. Do not
install the product in a kitchen or near a kitchen counter.
•• If rainwater enters the product, a fire or electric shock can occur.
!
When using an outdoor antenna, be sure to install the antenna away from
nearby power lines to prevent the antenna from collapsing onto them in
strong winds.
•• A collapsed antenna can cause an electric shock or injury.
!
Do not install the product on an unstable or vibrating surface (insecure shelf,
sloped surface, etc.)
•• The product may fall and become damaged and/or cause an injury.
•• Using the product in an area with excess vibration may damage the
product or cause a fire.
Do not install the product in a vehicle or a place exposed to dust, moisture
(water drips, etc.), oil, or smoke.
•• A fire or electric shock may result.
!
Do not expose the product to direct sunlight, heat, or a hot object such as a
stove.
•• The product lifespan may be reduced or a fire may result.
Do not install the product within the reach of young children.
•• The product may fall and injure children.
•• As the front is heavy, install the product on a flat and stable surface.
10
Operation
Caution
Do not drop the product while moving.
•• Product failure or personal injury may result.
Warning
There is a high voltage inside the product. Never disassemble, repair or
modify the product yourself.
!
•• A fire or electric shock may result.
Do not set down the product on its front.
•• Contact Samsung Customer Service Centre for repairs.
•• The screen may become damaged.
Before moving the product, turn off the power switch and disconnect the
power cord, antenna cable and all other connected cables.
When installing the product on a cabinet or shelf, make sure that the
bottom edge of the front of the product is not protruding.
•• Damage to the cord may result in a fire or electric shock.
!
•• The product may fall and become damaged and/or cause an injury.
If the product generates abnormal sounds, a burning smell or smoke,
disconnect the power cord immediately and contact Samsung Customer
Service Centre.
•• Install the product only on cabinets or shelves of the right size.
Set down the product gently.
•• Product failure or personal injury may result.
•• An electric shock or fire may result.
!
Do not let children hang from the product or climb on top of it.
!
•• Children may become injured or seriously harmed.
SAMSUNG
!
Installing the product in an unusual place (a place exposed to a lot of fine
dust, chemical substances, extreme temperatures or a significant presence
of moisture, or a place where the product will operate continuously for an
extended period of time) may seriously affect its performance.
•• Be sure to consult Samsung Customer Service Centre if you want to
install the product at such a place.
If the product is dropped or the outer case is damaged, turn off the power
switch and disconnect the power cord. Then contact Samsung Customer
Service Centre.
•• Continued use can result in a fire or electric shock.
11
Do not leave heavy objects or items that children like (toys, sweets, etc.) on
top of the product.
Do not use or keep combustible spray or an inflammable substance near
the product.
•• The product or heavy objects may fall as children try to reach for the
toys or sweets resulting in a serious injury.
•• An explosion or fire may result.
!
During a lightning or thunderstorm, remove the power cable and do not
touch the antenna cable.
Ensure the vents are not blocked by tablecloths or curtains.
•• An increased internal temperature may cause a fire.
•• A fire or electric shock may result.
!
Do not drop objects on the product or apply impact.
•• A fire or electric shock may result.
!
Do not move the product by pulling the power cord or any cable.
•• Product failure, an electric shock or fire may result from a damaged
cable.
If a gas leakage is found, do not touch the product or power plug. Also,
ventilate the area immediately.
•• Sparks can cause an explosion or fire.
!
100
Do not insert metallic objects (chopsticks, coins, hairpins, etc) or objects
that burn easily (paper, matches, etc) into the product (via the vent or input/
output ports, etc).
•• Be sure to power off the product and disconnect the power cord
when water or other foreign substances have entered the product.
Then contact Samsung Customer Service Centre.
•• Product failure, an electric shock or fire may result.
Do not place objects containing liquid (vases, pots, bottles, etc) or metallic
objects on top of the product.
•• Be sure to power off the product and disconnect the power cord
when water or other foreign substances have entered the product.
Then contact Samsung Customer Service Centre.
•• Product failure, an electric shock or fire may result.
GAS
Do not lift or move the product by pulling the power cord or any cable.
•• Product failure, an electric shock or fire may result from a damaged
cable.
12
Caution
Rest your eyes for more than 5 minutes for every 1 hour of product use.
•• Eye fatigue will be relieved.
Leaving the screen fixed on a stationary image for an extended period of
time may cause afterimage burn-in or defective pixels.
•• Activate power-saving mode or a moving-picture screen saver if you
will not be using the product for an extended period of time.
!
Do not touch the screen when the product has been turned on for an
extended period of time as it will become hot.
!
-_-
Disconnect the power cord from the power socket if you do not plan on
using the product for an extended period of time (vacation, etc).
•• Dust accumulation combined with heat can cause a fire, electric shock
or electric leakage.
Store small accessories out of the reach of children.
!
Use the product at the recommended resolution and frequency.
•• Your eyesight may deteriorate.
!
Exercise caution when adjusting the product angle or stand height.
!
•• Your hand or finger may get stuck and injured.
Do not hold the product upside-down or move it by holding the stand.
•• The product may fall and become damaged or cause an injury.
!
•• Tilting the product at an excessive angle may cause the product to fall
and an injury may result.
Do not place heavy objects on the product.
•• Product failure or personal injury may result.
Looking at the screen too close for an extended period of time can
deteriorate your eyesight.
When using headphones or earphones, do not turn the volume too high.
!
•• Having the sound too loud may damage your hearing.
Do not use humidifiers or stoves around the product.
•• A fire or electric shock may result.
13
Be careful that children do not place the battery in their mouths when
removed from the remote control. Place the battery in a location that
children or infants cannot reach.
•• If children have had the battery in their mouths, consult your doctor
immediately.
When replacing the battery, insert it with the right polarity (+, -).
•• Otherwise, the battery may become damaged or it may cause fire,
personal injury or damage due to leakage of the internal liquid.
Use only the specified standardized batteries, and do not use a new battery
and a used battery at the same time.
•• Otherwise, the batteries may be damaged or cause fire, personal injury
or damage due to a leakage of the internal liquid.
!
The batteries (and rechargeable batteries) are not ordinary refuse and must
be returned for recycling purposes. The customer is responsible for returning
the used or rechargeable batteries for recycling.
!
•• The customer can return used or rechargeable batteries to a nearby
public recycling centre or to a store selling the same type of the
battery or rechargeable battery.
14
Chapter 02
Preparations
Checking the Components
-- Contact the vendor where you
purchased the product if any
components are missing.
-- The appearance of the components and
items sold separately may differ from the
image shown.
Components
――Components may vary depending on the country and model.
-- The Mini Wall-mount Kit may not be
supported, depending on the model.
Warranty card
Quick setup guide
Batteries
(Not available in some locations)
Stand base
(Not available in some
locations)
Regulatory guide
Remote Control
Power cord
User manual / MagicInfo Express
(USB or DVD)
Mini Wall-mount Kit
(optional)
Stand neck
15
Items sold separately
-- The following items can be purchased
at your nearest retailer.
HDMI cable
HDMI-DVI cable
Stereo cable
D-SUB cable
Video cable
Audio cable
RCA stereo cable
16
――The colour and shape of parts may differ from what is shown.
Parts
Specifications are subject to change without notice to improve quality.
Panel Key
Control Panel
Buttons
Description
Power on the product.
If you press the
button when the product is turned on, the control menu will be
displayed.
――To exit the OSD menu, press and hold the panel key for at least one second.
POWER
Move to the upper or lower menu. You can also adjust the value of an option.
Change the channel in TV mode.
Speaker
Move to the left or right menu.
――You can adjust the volume by moving the panel key left or right when the control
menu is not displayed.
Panel Key
Remote sensor
Press a button on the remote control pointing at the sensor on the front of the
product to perform the corresponding function.
――Using other display devices in the same space as the remote control of this
product can cause the other display devices to be inadvertently controlled.
Remote sensor
Use the remote control within 7 m to 10 m from the sensor on the product at an angle of 30 from the left and right.
――Store used batteries out of reach of children and recycle.
――Do not use a new and used battery together. Replace both batteries at the same time.
――Remove batteries when the remote control is not to be used for an extended period of time.
17
――If you press the
button on the panel key when the product is turned on, the
control menu will be displayed.
Buttons
Description
Select the connected input source.
Control menu
Source
Move the panel key right to select Source
in the control menu.
When the list of input sources is displayed, move the panel key up or down to select
the desired input source. Next, press the panel key.
Display the OSD menu.
Menu
MagicInfo
in the control menu. The OSD control
Move the panel key left to select Menu
screen will appear. Move the panel key right to select the desired menu.
You can select a sub-menu item by moving the panel key up, down, left, or right.
To change settings, select the desired menu and press the panel key.
Enter MagicInfo mode.
Move the panel key up to select MagicInfo
in the control menu.
Power off the product.
Return
Power off
Move the panel key down to select Power off
Next, press the panel key.
Return
Exit the control menu.
in the control menu.
18
Reverse Side
Port
――The colour and shape of parts may differ from what is shown.
COMMON INTERFACE
Connect to a CI card.
HDMI IN 2 (DVI)
Connects to a source device using a HDMI cable or HDMI-DVI cable.
HDMI IN 1 (STB)
Connects to a source device using a HDMI cable or HDMI-DVI cable.
USB
Connect to a USB memory device.
Specifications are subject to change without notice to improve quality.
COMMON
INTERFACE
Description
(5V 0.5A) / CLONING
COMMON
INTERFACE
PC
AUDIO
IN
ANT IN AIR/CABLE
Connect to an antenna cable.
AUDIO OUT
Connects to the audio of a source device.
RS232C IN
Used for service purposes.
AV IN VIDEO / L-AUDIO-R
Connect to an external device using a video or Audio cable.
PC AUDIO IN
Receives sound from a PC via an audio cable.
PC IN
Connects to a source device using a D-SUB cable.
PC IN
VIDEO
AUDIO
HDMI IN 2
(DVI)
HDMI IN 1
(STB)
USB
(5V 0.5A)
/ CLONING
PC
AUDIO
IN
PC IN
L AUDIO R
RS232C IN
AV IN
VIDEO
ANT IN
AIR/CABLE
AUDIO
OUT
19
Anti-theft Lock
――An anti-theft lock allows you to use the product securely even in public places.
――The locking device shape and locking method depend on the manufacturer. Refer to the user guide provided with your anti-theft locking device for details.
――The following images are for reference only. Real-life situations may differ from what is shown in the images.
To lock an anti-theft locking device:
1
Fix the cable of your anti-theft locking device to a heavy object such as a desk.
2
Put one end of the cable through the loop on the other end.
3
Insert the locking device into the anti-theft lock slot at the back of the product.
4
Lock the locking device.
-- An anti-theft locking device can be purchased separately.
-- Refer to the user guide provided with your anti-theft locking device for details.
-- Anti-theft locking devices can be purchased at electronics retailers or online.
20
Remote Control
――Using other display devices in the same space as the remote control of this product can cause the other display devices to be inadvertently controlled.
――A button without a description in the image below is not supported on the product.
Display and select available video sources.
Turns the product On/Off.
Have direct access to channels.
Remote control button functions may
differ for different products.
Alternately selects Teletext, Double or Mix.
GUIDE
TTX/MIX
Cut off the sound temporarily.
Adjust the volume.
Display channel list on the screen.
Electronic Programme Guide (EPG) display.
Change channels.
CH LIST
Swich to the MagicInfo Screen.
Display the main on-screen menu.
HOME
CONTENT
Swich to the MagicInfo Screen.
21
CLOCK
Quickly select frequently used functions.
Press to display information on the TV screen.
CLOCK: When you press INFO key in standby
mode, TV screen displays the time.
Select on-screen menu items and change menu
values.
Return to the previous menu.
Configure the subtitle and audio
description options.
Not Available.
Exit the menu.
A
ALARM
B
C
D
Use TTX secondary function.
SUBT.
Play photos, videos or music.
Remote control button functions may
differ for different products.
To place batteries in the remote control
――Insert 2 AAA batteries, making sure to align the positive and negative polarities
correctly.
22
Before Installing the Product
(Installation Guide)
To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation instructions.
•• Ensure that an authorized installation company installs the wall mount.
•• Otherwise, it may fall and cause personal injury.
•• Make sure to install the specified wall mount.
Tilting Angle and Rotation
15 ˚
――Contact Samsung Customer Service Centre for further details.
•• The product can be tilted at a maximum angle of 15˚ from a perpendicular wall surface.
•• To use the product vertically (portrait), turn it clockwise so that the LED is pointing down.
Ventilation
Installation on a Perpendicular Wall
A Minimum 40 mm
B Ambient temperature: Under 35 C
A
•• When installing the product on a perpendicular wall, allow at least 40 mm of space between the product and wall surface
for ventilation and ensure that the ambient A temperature is kept below 35 C.
B
Figure 1.1 Side view
23
Figure 1.3 Side view
Installation on an Indented Wall
――Contact Samsung Customer Service Centre for further details.
B
D
D
Plane view
A Minimum 40 mm
B Minimum 70 mm
A
C Minimum 50 mm
D Minimum 50 mm
E Ambient temperature: Under 35 C
――When installing the product on an indented wall, allow at least the space specified above between the product and wall for
ventilation and ensure that the ambient temperature is kept below 35 C.
C
E
Figure 1.2 Side view
Dimensions
Unit: mm (inches)
Model name
5
1
2
4
1
1 2
23
34
45
RM40D
906.6 (35.69)
887.6 (34.94)
500.2 (19.69)
532.9 (20.98)
65.1 (2.56)
RM48D
1075.1 (42.33)
1056.1 (41.58)
594.9 (23.42)
627.6 (24.71)
65.5 (2.58)
――All drawings are not necessarily to scale. Some dimensions are subject to change without prior notice.
Refer to the dimensions prior to performing installation of your product. Not responsible for typographical or printed errors.
3
24
Installing the Wall Mount
Installing the Wall Mount Kit
The wall mount kit allows you to mount the product on the wall.
For detailed information on installing the wall mount, see the instructions provided with the wall mount.
We recommend you contact a technician for assistance when installing the wall mount bracket.
Samsung Electronics is not responsible for any damage to the product or injury to yourself or others if you elect to install the wall mount on your own.
25
Wall Mount Kit Specifications
――Install your wall mount on a solid wall perpendicular to the floor. Before
attaching the wall mount to surfaces other than plaster board, please contact
your nearest dealer for additional information.
If you install the product on a slanted wall, it may fall and result in severe
personal injury.
•• Samsung wall mount kits contain a detailed installation manual and all parts necessary for assembly are provided.
•• Do not use screws that are longer than the standard length or do not comply with the VESA standard screw
specifications. Screws that are too long may cause damage to the inside of the product.
•• For wall mounts that do not comply with the VESA standard screw specifications, the length of the screws may differ
depending on the wall mount specifications.
•• Do not fasten the screws too firmly. This may damage the product or cause the product to fall, leading to personal injury.
Samsung is not liable for these kinds of accidents.
•• Samsung is not liable for product damage or personal injury when non-specified wall mount is used or the consumer
fails to follow the product installation instructions.
•• Do not mount the product at more than a 15 degree tilt.
•• Always have two people mount the product on a wall.
•• Standard dimensions for wall mount kits are shown in the table below.
Unit: mm (inches)
Model name
Screw hole specs
(A * B) in millimeters
RM40D
200 × 200 (7.87 × 7.87)
RM48D
400 × 400 (15.75 × 15.75)
Standard Screw
M8 / L14~16
Quantity
4
――Do not install your Wall Mount Kit while your product is turned on. It may result in personal injury due to electric shock.
26
Chapter 03
Connecting and Using a Source Device
Before Connecting
Pre-connection Checkpoints
――Before connecting a source device, read the user manual provided with it.
The number and locations of ports on source devices may differ from device to
device.
――Do not connect the power cable until all connections are completed.
Connecting the power cable during connection may damage the product.
Connecting to a PC
•• Do not connect the power cable before connecting all other cables.
Ensure you connect a source device first before connecting the power cable.
•• A PC can be connected to the product in a variety of ways.
Select a connection method suitable for your PC.
――Connecting parts may differ in different products.
Connection using the D-SUB cable (Analogue type)
――Connect the sound ports correctly: left = white and right = red.
――Check the types of ports at the back of the product you want to connect.
PC IN
PC AUDIO IN
27
Connection Using an HDMI Cable
Connection Using an HDMI-DVI Cable
――When you connect a PC to the product using an HDMI-DVI cable, set Edit Name to DVI PC to access
video and audio content stored on the PC.
HDMI IN 1 (STB), HDMI IN 2 (DVI)
HDMI IN 1 (STB), HDMI IN 2 (DVI)
PC AUDIO IN
28
Connecting to a Video Device
•• Do not connect the power cable before connecting all other cables.
Ensure you connect a source device first before connecting the power cable.
•• You can connect a video device to the product using a cable.
――Connecting parts may differ in different products.
――Press the SOURCE button on the remote control to change the source.
Connection Using the AV Cable
AV IN / VIDEO
AV IN / L-AUDIO-R
29
Connection Using an HDMI-DVI Cable
――Audio will not be enabled if the product is connected to a video device using an HDMI-DVI cable. To
resolve this, additionally connect an audio cable to the audio ports on the product and video device.
When you connect a video device to the product using an HDMI-DVI cable, set Edit Name to DVI
Devices to access video and audio content stored on the video device.
――Supported resolutions include 1080p (50/60Hz), 720p (50/60Hz), 480p, and 576p.
Connection Using an HDMI Cable
Using an HDMI cable (up to 1080p)
•• For better picture and audio quality, connect to a digital device using an HDMI cable.
•• An HDMI cable supports digital video and audio signals, and does not require an audio cable.
•• The picture may not display normally (if at all) or the audio may not work if an external device that
uses an older version of HDMI mode is connected to the product. If such a problem occurs, ask the
manufacturer of the external device about the HDMI version and, if out of date, request an upgrade.
•• Be sure to use an HDMI cable with a thickness of 14 mm or less.
•• Be sure to purchase a certified HDMI cable. Otherwise, the picture may not display or a connection
error may occur.
HDMI IN 1 (STB), HDMI IN 2 (DVI)
•• A basic high-speed HDMI cable or one with ethernet is recommended.
This product does not support the ethernet function via HDMI.
PC AUDIO IN
HDMI IN 1 (STB), HDMI IN 2 (DVI)
30
Connecting to an Audio System
Connecting the Antenna
――Connecting parts may differ in different products.
――Connecting parts may differ in different products.
――When the product is powered on for the first time, basic settings are configured automatically.
Take extra care to ensure the wires inside the antenna cable are not bent.
AUDIO OUT
ANT IN
AIR / CABLE
31
Connecting to a TV Viewing Card slot
To watch paid channels, the “CI or CI+ CARD” must be inserted.
――Turn the TV off to connect or disconnect a CI card.
•• If you don’t insert the “CI or CI+ CARD”, some channels will display the message “Scrambled Signal”.
To connect the CI CARD, follow these steps:
――CI card slots are available, depending on the model.
Using the “CI or CI+ CARD”
•• The pairing information containing a telephone number, the “CI or CI+ CARD” ID the Host ID and
other information will be displayed in about 2~3 minutes. If an error message is displayed, please
contact your service provider.
•• When the configuration of channel information has finished, the message “Updating Completed” is
displayed, indicating the channel list is updated.
――You must obtain a “CI or CI+ CARD” from a local cable service provider.
――When removing the “CI or CI+ CARD”, carefully pull it out with your hands since dropping the “CI
or CI+ CARD” may cause damage to it.
――Insert the “CI or CI+ CARD” in the direction marked on the card.
――The location of the COMMON INTERFACE slot may be different depending on the model.
――“CI or CI+ CARD” is not supported in some countries and regions; check with your authorized
dealer.
――If you have any problems, please contact a service provider.
――Insert the “CI or CI+ CARD” that supports the current aerial settings. The screen will be distorted
or will not be seen.
32
Initial Setup
After powering on the product for the first time, configure basic settings such as the language, channel and time.
Language → Regional Settings → Channel Source → Auto Tuning (Auto Tuning does not appear if Set-top box or No TV(Signage Only) is selected.) → Network Settings → Clock → Auto Power Off →
Setup Complete!
――Refer to page 99 for details about the Setup.
Changing the Input source
Source allows you to select a variety of sources and change source device names.
Source List
――The screen may not display correctly if an incorrect source is selected for the source device you want to convert to.
MENU m → Applications → Source List → ENTER E
――To view detailed information about connected source devices, press the TOOLS button from the Source page.
――If the product is in portrait orientation, it is not possible to change Source List.
――Refer to page 83 for details about the Source List.
Source
TV
You can display the screen of a source device connected to the product. Select a source from source list to display the screen
of the selected source.
――The input source can also be changed by using the SOURCE button on the remote control.
HDMI1
HDMI2
AV
PC
USB
-- The displayed image may differ depending on the model.
33
Chapter 04
Screen Adjustment
Configure the Picture settings (Backlight, Colour Tone, etc.).
-- The layout of the Picture menu options may vary depending on the product.
Picture Mode
If the input source is PC or HDMI1 (when a PC is connected), HDMI2
(when a PC is connected)
MENU m → Picture → Picture Mode → ENTER E
•• Information: This mode reduces eye fatigue and is suitable for displaying information to the public.
Select a picture mode (Picture Mode) suitable for the environment where the
product will be used.
Different Picture Mode options are displayed depending on the current input
source.
If the input source is TV, HDMI1, HDMI2 or AV
Picture
Picture Mode
Information
· Backlight
55
· Contrast
100
· Brightness
45
· Sharpness
50
· Colour
50
· Tint (G/R)
•• Advertisement: This mode is suitable for displaying video content and indoor/outdoor advertisements.
――These options can be selected only when Edit Name is set to PC.
(SOURCE → Source → TOOLS → Edit Name → ENTER E)
G50
•• Dynamic: This mode is suitable when the ambient light is bright.
•• Standard: This mode is generally suitable for any environment.
•• Movie: This mode reduces eye fatigue.
R50
-- The displayed image may differ depending on the model.
34
Backlight / Contrast / Brightness /
Sharpness / Colour / Tint (G/R)
MENU m → Picture → ENTER E
Your product has several options for adjusting picture quality.
Input source
Picture Mode
PC, HDMI1 (when a PC is connected),
HDMI2 (when a PC is connected)
Information, Advertisement
Backlight / Contrast / Brightness /
Sharpness
AV, HDMI1, HDMI2
Dynamic, Standard, Movie
Backlight / Contrast / Brightness /
Sharpness / Colour / Tint (G/R)
TV
Dynamic, Standard, Movie
Backlight / Contrast / Brightness /
Sharpness / Colour
Picture
Picture Mode
Standard
· Backlight
55
· Contrast
100
· Brightness
45
· Sharpness
50
· Colour
50
· Tint (G/R)
G50
Adjustable options
――When you make changes to Backlight, Contrast, Brightness, Sharpness, Colour or Tint (G/R), the OSD will be adjusted
accordingly.
――You can adjust and store settings for each external device you have connected to an input on the product.
――Lowering picture brightness reduces power consumption.
R50
-- The displayed image may differ depending on the model.
35
Picture Size
choose size and aspect ratio picture displayed on screen.
Picture Size
MENU m → Picture → Picture Size → ENTER E
――Different Screen Adjustment options are displayed depending on the current input source.
•• Auto Wide: Automatically adjusts the picture size to the 16:9 aspect ratios.
Picture Size
Picture Size
· Position
· 4:3 Screen Size
Resolution Select
•• 16:9: Sets the picture to 16:9 wide mode.
16:9
•• Wide Zoom: Magnifies the picture size more than 4:3. A magnified picture can be moved up and down.
•• Zoom: Magnifies the 16:9 wide pictures vertically to fit the screen size. A magnified picture can be moved up and down.
•• 4:3: Sets the picture to basic 4:3 mode.
――Do not set your product to 4:3 format for a long time.
The borders displayed on the left and right, or top and bottom of the screen may cause image retention (screen burn)
which is not covered by the warranty.
•• Screen Fit: Displays the full image without any cut-off when HDMI1, HDMI2 (720p / 1080i / 1080p) signals are inputted.
-- The displayed image may differ depending on the model.
•• Smart View 1: Reduces the 16:9 picture by 50%.
――Smart View 1 is enabled only in HDMI1, HDMI2 mode.
•• Smart View 2: Reduces the 16:9 picture by 25%.
――Smart View 2 is enabled only in HDMI1, HDMI2 mode.
•• Custom: Changes the resolution to suit the user's preferences.
――Not available on analogue TVs.
•• Original ratio: If the input source is PC or HDMI1 (PC connection), HDMI2 (PC connection) the video will display in the
original aspect ratio.
36
Picture Sizes available by Input Source.
Input Source
Picture Size
ATV
Auto Wide, 16:9, Wide Zoom, Zoom, 4:3
DTV (1080i)
Auto Wide, 16:9, Wide Zoom, Zoom, 4:3, Screen Fit,
Smart View 2
AV (480i, 480p)
Auto Wide, 16:9, Wide Zoom, Zoom, 4:3, Custom
HDMI1, HDMI2 (720p, 1080i, 1080p)
16:9, Wide Zoom, Zoom, 4:3, Screen Fit, Smart View 1,
Smart View 2, Custom
HDMI1, HDMI2 (480i, 480p)
16:9, Wide Zoom, Zoom, 4:3, Smart View 1, Smart View 2,
Custom
PC, HDMI1 (when a PC is connected), HDMI2 (when a PC is
connected)
16:9, 4:3, Original ratio
37
Position
Adjusts the picture position. Position is only available if Picture Size is set to Wide Zoom, Zoom or Screen Fit.
――To use the Position function after selecting Wide Zoom, Zoom or Screen Fit, follow these steps.
Picture Size
Picture Size
Wide Zoom
· Position
1
Press the
button to select Position. Press the E button.
2
Press the
or
3
Press the E button.
button to move the picture up or down.
――If you want to reset the picture to its original position, select Reset in the Position screen.
· 4:3 Screen Size
――The picture will be set to its default position.
Resolution Select
-- The displayed image may differ depending on the model.
Zoom/Position
Adjusts the picture zoom and position. This option is available when the input source is set to HDMI1, HDMI2 (1080i/1080p) or
AV (1080i/1080p). Picture Size must be set to Custom for the option to be available.
Picture Size
Picture Size
Custom
· Zoom/Position
· 4:3 Screen Size
Resolution Select
1
Press the
2
Select the Zoom or Position. Press the E button.
3
Press the
4
Press the E button.
button to select Zoom/Position. Press the E button.
/
/
/
button to move the picture.
――If you want to reset the picture to its original position, select Reset in the Zoom/Position screen.
――The picture will be set to its default position.
-- The displayed image may differ depending on the model.
38
4:3 Screen Size
Available only when picture size is set to Auto Wide. You can determine the desired picture size at the 4:3 WSS (Wide Screen
Service) size or the original size. Each European country requires different picture size.
Picture Size
Picture Size
Custom
· Zoom/Position
· 4:3 Screen Size
16:9
Resolution Select
-- The displayed image may differ depending on the model.
Resolution Select
If the picture is not normal even when the resolution of the graphics card is one of the following, you can optimize the picture
quality by selecting the same resolution for the product as the PC using this menu.
Available resolutions: Off / 1024x768 / 1280x768 / 1360x768 / 1366x768
Picture Size
Picture Size
Custom
· Zoom/Position
· 4:3 Screen Size
16:9
Resolution Select
Off
-- Available in PC mode only.
-- The displayed image may differ depending on the model.
39
Auto Adjustment
Adjust frequency values/positions and fine tune the settings automatically
MENU m → Picture → Auto Adjustment → ENTER E
Picture
Auto Adjustment
-- Available in PC mode only.
-- The displayed image may differ depending on the model.
40
PC Screen Adjustment
•• Coarse / Fine
Removes or reduces picture noise.
MENU m → Picture → PC Screen Adjustment → ENTER E
•• Position
To adjust the PC’s screen position if it is not centred or does not fit the product screen.
PC Screen Adjustment
Coarse
Fine
If the noise is not removed by Fine-tuning alone, use the Coarse function to adjust the frequency as best as possible
(Coarse) and Fine-tune again. After the noise has been reduced, re-adjust the picture so that it is aligned with the centre
of screen.
50
0
Press the
or
button to adjust the Vertical Position. Press the
or
button to adjust the Horizontal Position.
•• Image Reset
Resets the image to the default settings.
Position
Image Reset
-- The displayed image may differ depending on the model.
41
PIP
MENU m → Picture → PIP → ENTER E
Picture
PIP
PIP Settings
The picture from the external video source will be in the main screen and the picture from the product will be in the PIP subpicture screen.
Main picture
Sub picture
AV, TV
PC, HDMI1, HDMI2
HDMI1, HDMI2
PC, TV, AV
PC
TV, AV, HDMI1, HDMI2
•• PIP (Off / On): Activate or deactivate the PIP function.
-- The displayed image may differ depending on the model.
-- For PIP sound, refer to the Sound Select instructions.
-- If you turn the product off while watching in the PIP mode, PIP mode will remain after power
Off/On.
•• Source: You can select a source of the sub picture.
•• Antenna (Air / Cable): Select either Air or Cable as the input source for the sub-screen.
――This option is enabled if the secondary display is set to TV.
•• Channel: Select the channel for the sub-screen.
――This option is enabled if the secondary display is set to TV.
•• Size (
,
•• Position (
,
――In Double (
,
,
,
,
,
,
,
,
): Select a size for the subpicture.
): Select a position for the sub-picture.
) mode, you cannot select Position.
•• Sound Select (Main / Sub): You can choose to listen to the sound from the Main picture or the Sub picture.
42
Advanced Settings
Input Source
MENU m → Picture → Advanced Settings → ENTER E
Advanced Settings
Dynamic Contrast
Medium
Black Tone
Off
Flesh Tone
0
RGB Only Mode
Colour Space
Picture Mode
Advanced Settings
PC, HDMI1 (when a PC is
connected), HDMI2 (when a
PC is connected)
Information,
Advertisement
White Balance / Gamma
TV, HDMI1, HDMI2, AV
Dynamic
Not available.
Standard
Dynamic Contrast / Black Tone / Flesh Tone / RGB
Only Mode / Colour Space / White Balance / Gamma /
Motion Lighting
Movie
Dynamic Contrast / Black Tone / Flesh Tone / RGB Only
Mode / Colour Space / White Balance / Gamma
Off
Native
White Balance
Gamma
0
-- The displayed image may differ depending on the model.
43
Dynamic Contrast
Advanced Settings
Dynamic Contrast
Medium
Black Tone
Off
Flesh Tone
0
RGB Only Mode
Colour Space
Off
Native
White Balance
Gamma
0
Adjust the screen contrast.
•• Off / Low / Medium / High
Black Tone
Select the black level to adjust the screen depth.
•• Off / Dark / Darker / Darkest
Flesh Tone
Emphasize pink Flesh Tone.
RGB Only Mode
Displays the Red, Green and Blue colour for making fine adjustments to the hue and saturation.
-- The displayed image may differ depending on the model.
•• Off / Red / Green / Blue
Colour Space
Adjusts the range and variety of colours (the colour space) available to create images.
•• Auto / Native
44
White Balance
Advanced Settings
Adjust the colour temperature for a more natural picture.
White Balance
Gamma
Motion Lighting
2 Point
0
Off
•• R-Offset / G-Offset / B-Offset: Adjust each colour’s (red, green, blue) darkness.
•• R-Gain / G-Gain / B-Gain: Adjust each colour’s (red, green, blue) brightness.
•• Reset: Resets the White Balance to its default settings.
-- The displayed image may differ depending on the model.
Gamma
Adjust the primary colour intensity.
Motion Lighting
Reduces power consumption by reducing screen brightness when the picture on the screen is in motion.
•• Off / On
45
Picture Options
Select an option using the and arrow keys,
the press E.
Use the arrow keys to change the setting, and then press E.
MENU m → Picture → Picture Options → ENTER E
Picture Options
Colour Tone
Colour Temp.
and
Off
Input source
Picture Mode
PC, HDMI1 (when a PC is
connected), HDMI2 (when a
PC is connected)
Information, Advertisement
Colour Tone / Dynamic Backlight
HDMI1, HDMI2
Dynamic, Standard, Movie
Colour Tone / Digital Clean View / MPEG Noise Filter /
HDMI Black Level / Dynamic Backlight
TV, HDMI1 (1080i), HDMI2
(1080i), AV
Dynamic, Standard, Movie
Colour Tone / Digital Clean View / MPEG Noise Filter /
Film Mode / Dynamic Backlight
10000K
Digital Clean View
Off
MPEG Noise Filter
Off
HDMI Black Level
Normal
Film Mode
Off
Dynamic Backlight
Off
Picture Options
-- The displayed image may differ depending on the model.
46
Colour Tone
Picture Options
Colour Tone
Colour Temp.
Off
10000K
Digital Clean View
Off
MPEG Noise Filter
Off
If the input source is PC, HDMI1 (PC connection), HDMI2 (PC connection).
•• Off / Cool / Standard / Warm
If the input source is AV, HDMI1, HDMI2 or TV.
•• Off / Cool / Standard / Warm1 / Warm2
――Warm1 or Warm2 will be deactivated when the Picture Mode is Dynamic.
――Settings can be adjusted and stored for each external device connected to an input on the product.
Colour Temp.
-- The displayed image may differ depending on the model.
Adjust the colour temperature (Red / Green / Blue). (Range: 3000K–15000K)
――This option is available when Colour Tone is set to Off.
Digital Clean View
If the broadcast signal received by your product is weak, you can activate the Digital Clean View feature to reduce any static
and ghosting that may appear on the screen.
•• Off / Low / Medium / High / Auto / Auto Visualisation
――Auto Visualisation: When changing analogue channels, displays signal strength.
――When the signal is weak, try all the options until the the product displays the best picture.
MPEG Noise Filter
Reduces MPEG noise to provide improved picture quality.
•• Off / Low / Medium / High / Auto
47
HDMI Black Level
Picture Options
Selects the black level on the screen to adjust the screen depth.
HDMI Black Level
Normal
Film Mode
Off
Dynamic Backlight
Off
•• Normal / Low
――Available only in HDMI1 (PC connection), HDMI2 (PC connection) mode (Enabled only when the colour format is RGB.).
Film Mode
This mode is suitable to view movies.
Sets the product to automatically sense and process film signals from all sources and adjust the picture for optimum quality.
-- The displayed image may differ depending on the model.
•• Off / Auto1 / Auto2
――Available in TV, AV.
Dynamic Backlight
Automatically adjust the backlight to provide the best possible screen contrast under the current conditions.
•• Off / On.
48
Picture Off
Selecting Picture Off switches off the screen. The volume is not disabled.
To switch the screen on, press any button other than the volume button.
MENU m → Picture → Picture Off → ENTER E
Picture
Picture Off
-- The displayed image may differ depending on the model.
Reset Picture
Resets your current picture mode to its default settings.
MENU m → Picture → Reset Picture → ENTER E
Picture
Reset Picture
-- The displayed image may differ depending on the model.
49
Chapter 05
Sound Adjustment
Configure the sound (Sound) settings for the product.
Sound Mode
You can select a sound mode to suit your personal preferences.
•• Standard: Selects the normal sound mode.
MENU m → Sound → Sound Mode → ENTER E
•• Movie: Provides the best sound for movies.
•• Clear Voice: Emphasizes voices over other sounds.
Sound
Sound Mode
•• Music: Emphasizes music over voices.
Standard
•• Amplify: Increase the intensity of high-frequency sound to allow a better listening experience for the hearing impaired.
――If Speaker Select is set to External, Sound Mode is disabled.
Sound Effect
Speaker Settings
Additional Settings
Reset Sound
-- The displayed image may differ depending on the model.
50
Sound Effect
MENU m → Sound → Sound Effect → ENTER E
Sound
Sound Effect
Configure your preferred sound effect for output sound.
――If Speaker Select is set to External, Sound Effect is disabled.
――Available only when Sound Mode is set to Standard.
•• DTS TruSurround HD (Off / On)
This function provides a virtual 5.1 channel surround sound experience through a pair of speakers using HRTF(Head
Related Transfer Function) technology.
•• DTS TruDialog (Off / On)
This function allows you to increase the intensity of a voice over background music or sound effects so that dialog can be
heard more clearly.
•• Equaliser
Use Equaliser to customize sound setting for each speaker.
-- The displayed image may differ depending on the model.
-- Balance L/R: Adjusts the balance between the right and left speaker.
-- 100Hz / 300Hz / 1kHz / 3kHz / 10kHz (Bandwidth Adjustment): Adjusts the level of specific bandwidth frequencies.
-- Reset: Resets the equalizer to its default settings.
51
Speaker Settings
MENU m → Sound → Speaker Settings → ENTER E
Sound
•• Speaker Select (External / Internal)
If you are listening to the sound track of a broadcast or movie through an external receiver, you may hear a sound echo
caused by the difference in decoding speed between the products speakers and the speakers attached to your audio
receiver. If this occurs, set the product to External.
――When you set Speaker Select to External, the products speakers are turned off.
You will hear sound through the external speakers only. When the Speaker Select is set to Internal, both the product
speakers and the external speakers are on. You will hear sound through both.
――If there is no video signal, both the products speakers and the external speakers will be mute.
Speaker Settings
•• Auto Volume (Off / Normal / Night)
The volume can vary depending on the channel.
Automatically equalize the volume level when switching to another channel.
-- The displayed image may differ depending on the model.
-- Normal equalizes the volume level on each channel, so that when you change channels, the volume level is the
same.
-- Night equalizes and decrease the volume level on each channel, so each channel is quieter. Night is useful at night,
when you may want to keep the volume low.
――To use the volume control of a connected source device, set Auto Volume to Off. A change to the volume control of
the connected source device may not be applied if Auto Volume is set to Normal or Night.
52
Additional Settings
DTV Audio Level
(Digital channels only)
MENU m → Sound → Additional Settings → ENTER E
Sound
Additional Settings
The TV cannot freely control the volume of the digital audio that it sends to the AV receiver. Use this to set the digital audio
volume at a comfortable level.
――According to the type of broadcast signal, MPEG / HE-AAC can be adjusted between -10dB and 0dB.
――To increase or decrease the volume, adjust between the range 0 and -10 respectively.
Dolby Digital Comp
Some digital TV programmes provide 5.1-channel Dolby audio. This TV converts Dolby audio to stereo audio so that it can play
the sound through the TV’s speakers. There are two methods to choose from. RF is for better sound at lower volumes, and Line
is for higher volumes.
-- The displayed image may differ depending on the model.
53
Reset Sound
Reset all sound settings to the factory defaults.
MENU m → Sound → Reset Sound → ENTER E
Sound
Reset Sound
-- The displayed image may differ depending on the model.
54
Chapter 06
Broadcasting
Configure the Broadcasting settings for the product.
Auto Tuning
The Auto Tuning function memorizes all channels that are available over the aerial or through your cable system and adds
them to the Channel List.
MENU m → Broadcasting → Auto Tuning → ENTER E
Auto Tuning
To start Auto Tuning, follow these steps:
Broadcasting
1
screen appears.
Auto Tuning
Aerial
Push MENU m → Broadcasting → Auto Tuning → Auto Tuning → ENTER E on your remote. The Auto Tuning
Air
2
Channel List
On the Auto Tuning screen, select the source of your product signal.
――Air: If your product is connected to an antenna choose Air, and then press ENTER E. The product will automatically
Guide
start memorizing channels.
――Cable: If your product is connected to a cable outlet, choose Cable, and then press ENTER E. Go to Step 3.
Schedule Manager
――Select Digital & Analogue, Digital or Analogue to scan for channels.
Edit Channel
Edit Favorites
3
Sets Search Mode using
/
buttons. When done, select Scan, and then press ENTER E. The product will start
memorizing channels.
――Channel memorization can take up to 45 minutes, depending on your cable system.
――Memorized channels are added to the Added Ch. list. These are the channels you will see when you use the channel
buttons on your remote.
-- The displayed image may differ depending on the model.
-- Available in TV mode only.
55
Cancelling Auto Tuning
Cable Search Option
MENU m → Broadcasting → Auto Tuning → Cable Search Option →
ENTER E
1
Press the Stop button.
2
A Stop Auto Tuning? message appears.
3
Press the Yes button.
(when the aerial was set to Cable)
Sets additional search options such as the frequency and symbol rate for a cable network search.
――Availability depends on the specific model and area.
Auto Tuning
Cable Search Option
-- The displayed image may differ depending on the model.
-- Available in TV mode only.
56
Aerial
Before your television can begin memorizing the available channels, you must specify the type of signal source that is
connected to the LED display.
•• Air / Cable
MENU m → Broadcasting → Aerial → ENTER E
Broadcasting
Aerial
Cable
-- The displayed image may differ depending on the model.
-- Available in TV mode only.
57
Channel List
MENU m → Broadcasting → Channel List → ENTER E
Register or delete channels. Add favourites channels or rename analogue channels.
Select a desired channel from Channel List to view the channel instantly.
――To navigate Channel List faster, press the channel buttons. The channel list changes page by page.
Icons found in the channel list page
Broadcasting
••
••
Channel List
••
A : Analogue channel
*: A channel that is selected
\ : Locked channels
Pressing the left cursor ( ) button on the remote control displays the Sorting page.
Pressing the right cursor ( ) button on the remote control displays the Mode page.
-- The displayed image may differ depending on the model.
-- Available in TV mode only.
Sorting
Sort the list by Channel Number or by Name (Digital channels only).
Mode
Antenna
Select either Air or Cable as digital channel mode.
Edit Favorites
Edit favourites channel lists from Edit Favorites.
Favourites 1 ~ Favourites 5
Shows all favourites channels, in up to five groups. Each group has a separate screen.
――The TV displays favourites groups only if you have added favouritess using Favourites 1 - to - Favourites 5.
58
All
Shows all channels.
Analog
Shows analogue channels.
Digital
Shows digital channels.
59
Guide
The Guide provides an overview of each digital channel's programme lineup. You can check the programme schedules and set
up a Schedule Manager.
――The information in the Guide is for digital channels only. Analogue channels are not supported.
MENU m → Broadcasting → Guide → ENTER E
You can press the colour keys on the remote to access optional functions.
Broadcasting
Guide
Quick Navigation
Search channel information quickly.
Schedule Manager
Access the Schedule Manager function.
You can view information on the Schedule Manager.
-- The displayed image may differ depending on the model.
-- Available in TV mode only.
60
Schedule Manager
MENU m → Broadcasting → Schedule Manager → ENTER E
Broadcasting
Watch a desired channel at a scheduled time.
•• Aerial: DTV Cable / Cable
•• Channel: Select the desired channel.
•• Repeat: Once / Manual / Sat~Sun / Mon~Fri / Everyday
――Select Manual if you want to configure settings by day of the week.
•• Date: Select the desired date.
•• Start Time: Set the time to watch the desired channel.
Schedule Manager
-- The displayed image may differ depending on the model.
-- Available in TV mode only.
61
Edit Channel
Manage channels saved on your TV. Delete channels, re-register deleted channels or rename analogue channels.
――Conveniently configure settings using the remote control buttons displayed at the bottom of the screen.
MENU m → Broadcasting → Edit Channel → ENTER E
Icons found in the edit channel page
Broadcasting
••
••
••
Edit Channel
A : Analogue channel
*: A channel that is selected
\ : Locked channels
Deleting/registering channels
Deleting channels
-- The displayed image may differ depending on the model.
Delete channels, if required. Note that deleting channels from the Recently Viewed or Most Viewed category does not
remove the channels permanently. The channels are only removed from the categories.
-- Available in TV mode only.
1
Select channels to delete from the screen. To cancel, select again.
2
After selecting channels, select Delete from the screen to delete the channels.
Re-registering deleted channels
Register deleted channels again, if required. Deleted channels are grayed out and can only be found in the list of all channels.
The register function is enabled for deleted channels only.
1
Press TOOLS on the screen to display the Tools page. Select Category from the sub-menu items and then select All.
2
From the list of all channels, select deleted channels you want to register again.
3
After selecting channels, select Add from the screen to re-register the channels.
62
Editing registered channels
Locking/unlocking channels using a password
Pressing TOOLS from the Edit Channel page displays the following menu items. Provided functions may
vary depending on the broadcast signal.
Lock specific channels to prevent children from accessing inappropriate content.
――To set a password, make sure Programme Rating Lock is set to On.
Option Name
Operations
Aerial
Select either Air or Cable as digital channel mode.
Category
Channels saved on your TV are classified under the All, Added Ch., Recently
Viewed and Most Viewed categories. Select a desired category.
Edit Favorites
Set frequently viewed channels as favourites channels.
Rename Channel
Change the names of analogue channels to suit your preferences. A channel
name can be up to five characters long.
Channel Info
Check the information of the channel.
Information
View information about the current broadcast programme on the aerial.
Locking channels
1
Select a channel from the Edit Channel page, and then select Programme Rating Lock from the
screen. The password input window is displayed.
2
Enter the password. The selected channel is locked.
Unlocking channels
1
Select a locked channel from the Edit Channel page, and then select Programme Rating Lock Off
from the screen. The password input window is displayed.
2
Enter the password. The selected channel is unlocked.
63
Edit Favorites
MENU m → Broadcasting → Edit Favorites → ENTER E
Broadcasting
Edit Favorites
-- The displayed image may differ depending on the model.
-- Available in TV mode only.
Creating a favourites channel list
Set frequently viewed channels as favourites channels. Favourites channels are indicated by a symbol in the Edit Channel or
Channel List page. A maximum of five favourites channel lists are allowed. Create different favourites channel lists for each
family member.
――Conveniently configure settings using the remote control buttons displayed at the bottom of the screen.
Adding the current channel to a favourites channel list
Add the channel you are currently watching to a favourites channel list.
1
When watching TV, press TOOLS to display the Tools page. Select Edit Favorites from the sub-menu items.
2
From the displayed prompt box, select a favourites channel list to save the current channel to. Select OK.
3
The current channel is added in the selected favourites channel list. Select OK.
Adding multiple channels to a favourites channel list
Add multiple channels to a favourites channel list, if required.
1
Select Category from the screen to change the channel list in the centre of the screen to the channel list that contains
the channels to add. Each time Category is selected, the category switches in the order Recently Viewed, Most Viewed,
and Added Ch..
――Recently Viewed and Most Viewed are only enabled if they contain saved channels.
2
Select desired channels from the channel list in the centre of the screen.
3
Select Change Fav. from the screen to change the favourites channel list on the right to another desired favourites
channel list.
4
Select Add from the screen. The selected channels will create a favourites channel list.
64
Viewing channels saved under a favourites channel list
Deleting channels from a favourites channel list
――Favourites channel lists are only displayed if they have been created previously.
Delete channels from a favourites channel list, if required.
When changing the channel using the channel buttons, channels saved in favourites channel lists can
only be accessed.
1
1
Select Channel List from the Broadcasting menu. The channel list is displayed.
2
Pressing the right cursor ( ) button on the remote control displays the Mode page.
3
Select a favourites channel list among Favourites 1 – Favourites 5.
4
Select channels from the selected favourites channel list.
――Selecting Channel List while watching a favourites channel will display the updated favourites
channel list.
Select Change Fav. from the screen to change the favourites channel list on the right to another
desired favourites channel list.
2
Select channels to delete from the selected favourites channel list.
3
Select Delete from the screen. The selected channels are deleted from the favourites channel list.
Changing the order of channels in a favourites channel list
Change the order of channels saved in a favourites channel list, if required.
1
Select Change Fav. from the screen to change the favourites channel list on the right to another
desired favourites channel list.
Editing favourites channel lists
Pressing TOOLS from one of the Favourites 1 - to - Favourites 5 pages displays the following menu
items.
Option Name
Copy to Favorites
Operations
2
Select channels to rearrange from the selected favourites channel list.
3
Select Change order from the screen, and then change the order of the selected channels. To apply
the new order of the channels, press the E button.
Copy channels from a favourites channel list to another favourites channel
list.
――This option is only available when channels under a favourites channel list
are selected.
Rename Favorites
Change the name of a favourites channel list.
――This option is only available when channels under a favourites channel list
are selected.
Aerial
Select either the Air or Cable signal.
Edit Channel
Manage saved channels.
Information
View information about the current broadcast programme on the aerial.
65
Renaming a favourites channel list
Change the name of a favourites channel list, if required.
1
Select Change Fav. from the screen to change the favourites channel list on the right to another desired favourites channel list.
2
Press TOOLS on the screen. Sub-menu items are displayed.
3
Select Rename Favorites from the sub-menu items. A prompt box appears.
4
Change the favourites channel list using the prompt box. The name for a favourites channel list can be up to 20 characters long.
Copying channels between favourites channel lists
Copy channels from a favourites channel list to another favourites channel list, if required.
1
Select Change Fav. from the screen to change the favourites channel list on the right to another desired favourites channel list.
2
Select channels to copy from the favourites channel list on the right.
3
Press TOOLS on the screen. Sub-menu items are displayed.
4
Select Copy to Favorites from the sub-menu items. A prompt box appears.
5
Select favourites channel lists to copy the channels to using the prompt box. The channels are saved to the selected favourites channel lists.
――To use Copy to Favorites, make sure channels are saved in a favourites channel list.
66
Channel Settings
Country (Area)
Select your country so that the TV can correctly auto-tune the broadcasting channels. This depends on the country or region.
MENU m → Broadcasting → Channel Settings → ENTER E
When the PIN input screen appears,enter your 4 digit PIN number.
•• Digital Channel: Change the country for digital channels.
Channel Settings
•• Analogue Channel: Change the country for analogue channels.
Country (Area)
Manual Tuning
Manual Tuning
Scans for a channel manually and stores in the TV.
Fine Tune
Transfer Channel List
Delete CAM Operator Profile
If a channel is locked using the Channel Lock function, the PIN input window appears.
This function depends on the country and region.
When Aerial Source is set to Air or Cable
•• Digital Channel Tuning: Scans for a digital channel.
1
Select the New.
――When selecting Aerial → Air: Channel, Frequency, Bandwidth
-- The displayed image may differ depending on the model.
-- Available in TV mode only.
――When selecting Aerial → Cable: Frequency, Modulation, Symbol Rate
2
Select the Search. When scanning has finished, a channel is updated in the channel list.
•• Analogue Channel Tuning: Scans for an analogue channel.
1
Select the New.
2
Set the Programme, Colour System, Sound System, Channel and Search.
――Channel
C (aerial channel mode) / S (cable channel mode): These two modes allow you to select a channel by entering the
assigned number for each aerial broadcasting station or cable channel.
3
Select the Store. When scanning has finished, a channel is updated in the channel list.
67
Fine Tune
(analogue channels only)
If the reception is clear, you do not have to fine tune the channel, as this is done automatically during the search and store
operation. If the signal is weak or distorted, fine tune the channel manually. Scroll to the left or right until the image is clear.
――This function is only available in Cable mode.
――Settings are applied to the channel you’re currently watching.
――Fine tuned channels that have been saved are marked with an asterisk “*” on the right-hand side of the channel number in
the channel banner.
――To reset the fine-tuning, select Reset.
Transfer Channel List
Imports or exports the channel map. When the PIN input screen appears, enter the PIN.
You should connect a USB storage device to use this function.
•• Import from USB: Import channel list from USB.
•• Export to USB: Export channel list to USB. This function is available when USB is connected.
Delete CAM Operator Profile
Select the CAM operator to delete.
――Availability depends on the specific model and area.
68
Subtitle
MENU m → Broadcasting → Subtitle → ENTER E
Subtitle
Subtitle
· Subtitle Mode
· Subtitle Language
Primary Subtitle
Secondary Subtitle
Configures the subtitle options.
Subtitle
Show subtitles.
•• Subtitle Mode: Set the subtitle mode.
•• Subtitle Language: Set the subtitle language.
Primary Subtitle
Set the primary subtitle language.
Secondary Subtitle
Set the secondary subtitle language.
-- The displayed image may differ depending on the model.
-- Available in TV mode only.
69
Audio Options
Audio Language
(for digital broadcasts)
MENU m → Broadcasting → Audio Options → ENTER E
Change the default value for audio languages.
•• Primary Audio: Set the primary audio language.
•• Secondary Audio: Set the secondary audio language.
――The available language may differ depending on the broadcast.
Audio Options
Audio Language
Audio Format
English
Stereo
Audio Description
-- The displayed image may differ depending on the model.
-- Available in TV mode only.
Off
Audio Format
(for digital broadcasts)
Change a desired audio format. The supported audio format may vary depending on the broadcast programme.
Audio Description
(Not available in all locations) (for digital broadcasts)
This function handles the Audio Stream for the AD (Audio Description) which is sent along with the Main audio from the
broadcaster.
•• Audio Description: Turn the audio description function on or off.
•• Volume: Adjust the audio description volume.
70
Programme Rating Lock
The Programme Rating Lock blocks programmes with ratings higher than those desired. This is useful for controlling what
children watch on TV. This will not function for programmes originating from external sources, such as DVD players or USB files.
MENU m → Broadcasting → Programme Rating Lock → ENTER E
This PIN is required to watch a blocked programme.
――This option is available when the input source is TV.
――The default PIN number for a new product set is “0-0-0-0”.
Broadcasting
――Availability depends on the specific model and area.
Programme Rating Lock
-- The displayed image may differ depending on the model.
-- Available in TV mode only.
71
Digital Text
Digital Text
MENU m → Broadcasting → Digital Text → ENTER E
Enable or disable the MHEG function.
――The MHEG function is enabled only in countries where it is supported.
•• Disable / Enable
Broadcasting
Digital Text
Enable
-- The displayed image may differ depending on the model.
-- Available in TV mode only.
72
Teletext Language
Teletext Language
MENU m → Broadcasting → Teletext Language → ENTER E
Use this to set the teletext language.
――Availability depends on the specific model and area.
Broadcasting
Primary Teletext
Set the primary teletext language.
Teletext Language
Secondary Teletext
Set the secondary teletext language.
-- The displayed image may differ depending on the model.
-- Available in TV mode only.
73
Common Interface
CI Menu
Enables the user to select from the CAM-provided menu. Select the CI Menu based on the menu PC Card.
MENU m → Broadcasting → Common Interface → ENTER E
Broadcasting
Common Interface
CAM video transcoding
You can configure the setting to transcode the video codec from the CAM automatically. Turn it Off if you do not want to use it.
Application Info
View information about the CAM inserted into the CI slot and about the “CI or CI+ CARD” inserted into the CAM. You can install
the CAM any time, with or without the TV turned on.
-- The displayed image may differ depending on the model.
-- Available in TV mode only.
1
Purchase a CI CAM module at your nearest dealer or by phone.
2
Firmly insert the “CI or CI+ CARD” into the CAM in the direction of the arrow.
3
Insert the CAM with the “CI or CI+ CARD” into the common interface slot, in the direction of the arrow so that it aligns
parallel with the slot.
4
Check if you can see a picture on a scrambled signal channel.
74
Channel Lock
Prevent your children from accessing harmful content by locking channels.
MENU m → Broadcasting → Channel Lock → ENTER E
•• On / Off
――This option is available when the input source is TV.
――The default PIN number for a new product set is “0-0-0-0”.
――Availability depends on the specific model and area.
Broadcasting
Channel Lock
On
-- The displayed image may differ depending on the model.
-- Available in TV mode only.
75
Chapter 07
Network
Network Status
Network Settings
MENU m → Network → Network Status → ENTER E
MENU m → Network → Network Settings → ENTER E
You can check the current network status.
Connect to a wireless network and use the product as a TV+signage using MagicInfo Express on your
PC.
Network Status
Your wireless network is set up and ready to use.
MAC Address
IP Address
Subnet Mask
Gateway
Network Settings
** : ** : ** : ** : ** : **
***.
***.
***.
***.
***.
***.
***.
***.
***.
***.
***.
***.
Your wireless network is set up and ready to use.
AP0000
Ready to play your business content.
-Run the Content Creator on your PC, then create and schedule your content. You can send
it to the Signage TV using the wireless network.
-Refer to the Content Creator manual for more information.
Disconnect
IP Settings
Retry
Close
Ready to play your business content.
-Run the Content Creator on your PC, then create and schedule your content. You can
send it to the Signage TV using the wireless network.
-Refer to the Content Creator manual for more information.
-- The displayed image may differ depending on the model.
-- The displayed image may differ depending on the model.
76
Network Setting (Wireless)
Connecting to a Wireless Network
Automatic Network Setup (Wireless)
Most wireless networks have an optional security system that requires devices that access the network
to transmit an encrypted security code called an Access or Connection Information. The Connection
Information is based on a Pass Phrase, typically a word or a series of letters and numbers of a specified
length you were asked to enter when you set up security for your wireless network. If you use this method
of setting up the network connection, and have a Connection Information for your wireless network,
you will have to enter the Pass Phrase during the the automatic or manual setup process.
How to set up automatically
1
Go to MENU m → Network → Network Settings.
2
The Network function searches for available wireless networks. When done, it displays a list of the
available networks.
Samsung recommends using IEEE 802.11n. When you play video over a network connection, the video
may not play smoothly.
――Select a channel for the wireless IP sharer that is not currently being used. If the channel set for the
3
――If the desired wireless router does not appear, select Refresh to search again.
wireless IP sharer is currently being used by another device nearby, this will result in interference and
communication failure.
――If the router cannot be found after retrying, select the Stop button.
The Add Network button appears.
Select Add Network to add a wireless router to connect to.
――Your product supports only the following wireless network security protocols.
If you select the Pure High-throughput (Greenfield) 802.11n mode and the Encryption type is set to
WEP, TKIP or TKIP AES (WPS2Mixed) on your AP or wireless router, Samsung products will not support a
connection in compliance with new Wi-Fi certification specifications.
4
If the Enter password. screen appears, go to step 5. If you select a wireless router that does not
have security, go to step 7.
――If your wireless router supports WPS (Wi-Fi Protected Setup), you can connect to the network via PBC
(Push Button Configuration) or PIN (Personal Identification Number). WPS will automatically configure
the SSID and WPA key in either mode.
In the list of networks, press the ▲ or ▼ button to select a network, and then press the E button.
5
If the router has security, enter the Enter password. (Security key or PIN).
――Connection Methods: You can setup the wireless network connection in three ways.
Auto Setup (Using the Auto Network Search function), Manual Setup, WPS(PBC)
77
6
When done, use the down arrow button to move the cursor to Done, and then press E. The
How to set up manually
network connection screen appears and the verification process starts.
On the SMART Signage TV, go to MENU m → Network → Device Name and change the SMART
Signage TV's device name.
――If you use multiple SMART Signage TVs, make sure to change their device names.
――This product cannot connect to the Internet via Soft AP (Wi-Fi Hotspot) or Wi-Fi Direct.
7
When the connection has been verified, the “Your wireless network is set up and ready to use.”
message appears.
1
Go to MENU m → Network → Network Settings.
2
The Network function searches for available wireless networks. When done, it displays a list of the
Manual Network Setup (Wireless)
Offices may use static IP addresses.
If this is the case, ask the network administrator for the IP address, subnet mask and gateway. Enter these
values manually.
available networks.
3
――If the desired wireless router does not appear, select Refresh to search again.
――If the router cannot be found after retrying, select the Stop button.
Getting the Network Connection Values
The Add Network button appears.
Select Add Network to add a wireless router to connect to.
To view the Network connection values on most Windows computers, follow these steps.
1
Right click the Network icon on the bottom right of the screen.
2
In the pop-up menu that appears, click Status.
3
On the dialog that appears, click the Support tab.
4
On the Support Tab, click the Details button. The Network connection values are displayed.
In the list of networks, press the u or d button to select a network, and then press the E button.
4
If the Enter password. screen appears, go to step 5. If you select a wireless router that does not
have security, go to step 7.
5
If the router has security, enter the Enter password. (Security key or PIN).
6
When done, use the down arrow button to move the cursor to Done, and then press E. The
network connection screen appears and the verification process starts.
7
Select Stop while network connections are being attempted. This will stop the connection.
8
Select IP Settings on network connection screen. The IP Settings screen appears.
9
Select the field at the top, press E, and then set IP Settings to Enter manually. Repeat the entry
process for each field in the IP Address.
78
10When done, select OK at the bottom of the page, and then press E. The network test screen
appears and the verification process starts.
11When the connection has been verified, the “Your wireless network is set up and ready to use.”
message appears.
WPS(PBC)
How to set up using WPS(PBC)
If your router has a WPS(PBC) button, follow these steps.
1
Go to MENU m → Network → Network Settings.
2
Select WPS(PBC), press E, and then press E again.
3
Press the WPS(PBC) button on your router within 2 minutes. Your product automatically acquires all
the network setting values it needs and connects to your network.
4
The network connection screen appears, and network setup is done.
79
Soft AP (Wi-Fi Hotspot)
MENU m → Network → Soft AP (Wi-Fi Hotspot) → ENTER E
Using this function, you can connect the product on your mobile devices if your mobile devices do not support Wi-Fi Direct.
Set the options for connection of Wi-Fi device.
•• Soft AP (Wi-Fi Hotspot)
Turns on or off the Soft AP (Wi-Fi Hotspot). When Soft AP (Wi-Fi Hotspot) is set to On, your mobile devices can find the product name in Wi-Fi connection list.
•• Connection Information
Shows the security key.
•• Reset password
Powering on the display creates a new security key and disconnect any existing Soft AP (Wi-Fi Hotspot) connection.
-- Off / On
•• Advanced Settings
Change detailed Wi-Fi settings.
-- Channel (CH.1 ~ CH.11)
Change Wi-Fi channel settings.
-- Signal Level (Level 1 ~ Level 5)
Change Wi-Fi signal level settings.
80
Wi-Fi Direct
To use this function, your mobile device
should be supported by the Wi-Fi Direct.
MENU m → Network → Wi-Fi Direct → ENTER E
Set to connect the product to wireless mobile devices. Using this function, you can connect wireless mobile devices with your product directly without a router.
To connect your mobile device with your product using Wi-Fi Direct, follow these steps:
1
Go to Wi-Fi Direct screen. The product starts to search devices.
2
Turn on the Wi-Fi Direct function on your device. Select the desired Wi-Fi device.
•• PBC (Push Button Configuration): Press the WPS(PBC) button on your Wi-Fi device within 2 minutes. Your product automatically acquires all the network setting
values it needs and connects to your network.
•• PIN: Input the displayed PIN on your device.
――If you want to disconnect the device, select the connected Wi-Fi device, and then select Disconnected.
81
AllShare Settings
MENU m → Network → AllShare Settings → ENTER E
Shows a list of mobile phones or connected devices which have been set up to use the AllShare Play function with this product.
•• Content Sharing
Using the AllShare Play Function
An alarm window appears informing you that media contents (videos, photos, music) sent from a mobile phone will be displayed on your product. The contents are played
automatically 3 seconds after the alarm window appears. If you press the RETURN or EXIT button when the alarm window appears, the media contents are not played.
――The first time a device accesses your product through the media function, a warning popup window appears. Press the E button to select Allow. This permits the
phone to access the product freely and use the AllShare Play function to play content.
――To turn off media contents transmissions from a mobile phone, set Deny in the AllShare Settings.
――Contents may not play on your product depending on their resolution and format.
――The E and ◄ / ► buttons may not work depending on the type of media content.
――Using the mobile device, you can control the AllShare Play. For details, refer to each mobile’s user’s guide.
Device Name
MENU m → Network → Device Name → ENTER E
Select or enter a device name.
This name can be shown on network remote controls over the network.
82
Chapter 08
Applications
Source List
Source allows you to select a variety of sources and change source device names.
MENU m → Applications → Source List → ENTER E
――The screen may not display correctly if an incorrect source is selected for the source device you want to convert to.
Source
TV
You can display the screen of a source device connected to the product. Select a source from source list to display the screen
of the selected source.
――The input source can also be changed by using the SOURCE button on the remote control.
――To view detailed information about connected source devices, press the TOOLS button from the Source page.
HDMI1
HDMI2
AV
PC
USB
Edit Name
SOURCE → Source → TOOLS → Edit Name → ENTER E
Sometimes the screen will not display properly unless the name of a source device is specified in Edit Name.
In addition, it is best to rename the source device in Edit Name to obtain optimal picture quality.
――The list can include the following source devices. Source devices on the list differ depending on the selected source.
PC / Cable STB / Satellite STB / PVR STB / Game / Blu-ray / DVD / VCR / AV Receiver / Camcorder / DVI PC / DVI
Devices / TV / IPTV / HD DVD / DMA
-- The displayed image may differ depending on the model.
――Available settings in the Picture menu depend on the current source and settings made in Edit Name.
Information
SOURCE → Source → TOOLS → Information → ENTER E
You can see detailed information about the selected external device.
83
MagicInfo
MENU m → Applications → MagicInfo → ENTER E
Applications
MagicInfo
MagicInfo is a business solution that allows the product to be used as a signage (advertising media). Using the solution, play
image and video files from the internal memory or a connected USB storage device. You can also play schedules created using
the MagicInfo Express on your computer.
Playing content from the internal memory or USB
Play content from the internal memory or a connected USB storage device.
Playing PC or mobile content
Send content via the MagicInfo Express or a mobile app to the product for playback. If the internal memory is insufficient,
connect a USB device and go to Options → Settings → Default Storage at the top right of the MagicInfo browser. Change
the option to USB.
-- The displayed image may differ depending on the model.
84
Device : All
Content : All
Sort by : File Name
Options
Schedule
Play configured schedules.
Schedule
Available features in the MagicInfo page
The MagicInfo list page provides the following features.
•• Device
-- Select either Internal or USB to search for a desired device list.
All / Internal / USB
-- Press HOME or MagicInfo Player I on the remote control to access the application more
quickly.
-- The displayed image may differ depending on the model.
•• Content
-- Select a content type as criterion to search for a desired content list.
All / My Templates / Video / Image
•• Sort by
Specify the content sort criterion.
-- File Name / Recently played
•• Options
Options menu items in the MagicInfo screen
Option Name
Operations
Play Selected
Select and play desired content.
Send
Copy content to another storage device.
Delete
Delete desired content.
Settings
Configure detailed properties of content.
――See the following page for details on the Settings feature.
85
Settings
Default Storage
Select the storage location that you want to download scheduled channels from the network to.
Settings
•• Internal / USB
Select the storage location that you want to download scheduled channels from
the network to.
Default Storage
Repeat Mode
Picture Size
Repeat Mode
Internal
One
Set repeat mode whether to repeat playing contents or not.
Close
Display Duration
Safely Remove USB Device
Reset Settings
•• One / All
Picture Size
Set Picture Size to either Original Size or Full Screen.
•• Original Size / Full Screen
――Available only for Video and Image content.
-- The displayed image may differ depending on the model.
Display Duration
Set the duration for each page in a slideshow.
――Available only for Template and Image content.
Safely Remove USB Device
Safely removes USB memory
Reset Settings
Restore all the values under Settings to the default when the product was purchased.
86
Chapter 09
MagicInfo Express
Use the USB or DVD that came with the product to install the software. The latest software updates may differ from the originals included at time of purchase.
Download the latest version of the MagicInfo Express software and manual at: http://www.samsung.com/displaysolutions/signagetv.
Installation requirements
Using MagicInfo Express
-- HDD: At least 500 MB of free space
-- Operating system: Windows XP or later
-- Resolution: 1024x768 or higher
MagicInfo Express is a programme that allows you to conveniently create SMART Signage TV content using a variety of templates. Using MagicInfo Express, create and
manage schedules to play content on SMART Signage TV at a specific time.
――To use MagicInfo Express, download and install MagicInfo Express from the MagicInfo Express USB/DVD or http://www.samsung.com/displaysolutions/signagetv.
――Connect the USB/DVD that came with the product to your PC. The install screen appears automatically. Select MagicInfo Express to install the programme. If the install
screen does not appear automatically, run the autorun.exe file stored on the USB/DVD using a file browser.
•• Create Content: Create and manage templates that will be played on Samsung display devices.
•• Schedule Content: Create and manage schedules to play content at specified times.
Managing templates
Using the templates provided in the programme, organize a variety of content items based on predefined layouts to conveniently create new templates. Import and edit
previously created templates.
Managing schedules
Configure and manage schedules to play content on Samsung display devices at specific times. Set the same schedule to play on specified days of the week or set different
schedules to play by day of the week.
87
Chapter 10
Playing photos, videos and music (Media Play)
Enjoy videos, photos, music files saved on a USB Mass Storage Class (MSC) device.
Play photos, videos or music saved on a storage device.
Play a variety of content using the following methods.
•• Using a USB device: Play media content such as videos, photos and music from a USB device.
•• Connecting a storage device: Play media content saved on a storage device such as a smartphone, camera, PC or cloud service.
Read the following before using media play with a USB device
Caution
•• Before connecting a USB device to the product, back up files to ensure your data is not damaged or lost.
Samsung Electronics is not liable for any damage or loss of data.
•• Do not remove a USB device while it is loading.
•• If a USB device is connected using a USB extension cable, the USB device may not be recognized or files saved on the device may not be able to be read.
•• If the product does not recognize a connected USB device, the files on the USB device may be corrupted or may not be able to be played.
If this occurs, connect the USB device to the PC to format the device, then make sure the device is connected properly.
•• USB HDD greater than 2TB is not supported.
88
Compatible devices with media play
•• Some USB digital cameras, smartphones and audio devices may not be compatible with the product.
•• Media play is only compatible with USB MSC devices.
•• MSC device refers to a Mass Storage Class Bulk-Only Transport device.
Examples of MSC devices include Thumb drives, Flash card readers and USB HDDs. (USB hubs are not supported.)
These MSC devices must be connected directly to a USB port on the product.
•• If more than one Picture Transfer Protocol (PTP) device is connected, only one will work at a time.
•• If multiple MSC devices are connected, some devices may not be recognized. USB devices that require high power (higher than 500mA or 5V) may not be supported.
•• If an overheating warning message appears when a USB device is connected or used, the USB device may not be recognized or function properly.
•• The screensaver activates if the product is left idle for a period of time specified in Auto Protection Time.
•• Power-saving mode on some external hard disk drives may automatically deactivate after connecting to the product.
File system and formats
•• Media play may not function properly with unlicenced multimedia files.
•• Media Transfer Protocol (MTP) is not supported.
•• Supported file systems include FAT16, FAT32 and NTFS (read only).
•• Media play supports the sequential JPEG format.
It does not support the progressive JPEG format.
•• Images with a higher resolution take longer to be displayed on the screen.
•• The maximum JPEG resolution supported is 15360x8640 pixels.
•• If a file is incompatible or corrupted, a message Not Supported File Format. appears.
•• When sorting files in folder view mode, a maximum of 1000 files can be displayed in each folder.
•• If a USB device contains 8000 files and folders or more, some files and folders may not open.
•• DRM MP3 files downloaded from websites that charge a fee cannot be played.
――Digital Rights Management (DRM) refers to a system for protecting the copyrights of data circulated via the Internet or other digital media by enabling secure
distribution and/or disabling illegal distribution of the data.
89
Using a USB device
It is recommended to use a USB HDD that
has a power adapter.
Connecting a USB device
1
Turn on your product.
2
Connect a USB device containing photo, music and/or movie files to the USB port on the back or side panel of the product.
3
The New device connected. page automatically appears as soon as a USB device connects to the product.
――If only one USB device is connected, files saved on the USB device are displayed automatically.
――To view content saved on a USB device, connect the USB device to a USB port on the product.
Removing a USB device
It is recommended to remove a USB
device using the Disconnect USB Device
function.
Removing a USB device from Source
1
Press SOURCE on the remote control. Alternatively, go to Source using the OSD menu.
SOURCE → Source
2
Select USB from Source, and then press the TOOLS button on the remote control. Optional menu items are displayed.
3
Select Disconnect USB Device and wait until the USB device is disconnected. The USB device is disconnected.
90
Menu items in the media content list page
Option Name
Operations
Slide Show
Start a slideshow.
――This menu item is not available if Sort by is set to Folder.
Encoding
Select an encoding language if the title of media content appears corrupted.
Play Selected
Select and play desired content from the media content list.
Photos
Videos
Music
c
c
c
c
c
91
Available buttons and features during photo playback
Pressing the E or TOOLS button displays the following buttons. The RETURN button makes the buttons disappear.
Pressing the INFO button while a file is
selected will display information about the
selected file.
•• Previous / Next
View the previous or next photo.
•• Start Slide Show / Stop Slide Show
Start or stop a slideshow. Using a slideshow, it is possible to play all photos in a folder.
•• Slideshow Settings
-- Speed: Change the slideshow speed.
-- Effects: Apply transition effects between photos.
•• Zoom
Zoom in on photos up to 4x.
•• Rotate
Rotate photos.
•• Background Music
Play background music while viewing photos.
-- Background Music / Mini Player
――Make sure a music file is saved on the same device.
――Pause the current music playing or switch to another music file using Mini Player.
•• Settings
Option Name
Operations
Picture Mode
Change the Picture Mode.
Sound Mode
Change the Sound Mode.
――This menu item is only available when Background Music is playing.
Information
View information about a file.
92
Available buttons and features
during video playback
Pressing the E or TOOLS button displays the following buttons. The RETURN
button makes the buttons disappear.
•• Pause / Play
Pause or play a video.
The following features are available in pause mode. Note that sound cannot
be heard in pause mode.
Option Name
Operations
Picture Mode
Change the Picture Mode.
Sound Mode
Change the Sound Mode.
Audio Language
Play a video using a desired language. This feature only activates when a streaming file that
supports multiple audio formats is playing.
Information
View information about a file.
•• Rewind / Fast Forward
Rewind or fast forward a video. Speed up playback up to 3x, if required. To
change the playback speed to the original speed, select ∂.
•• Previous / Next
To play the previous video, select  twice. Selecting  once will play the
current video from the beginning.
To play the next video, select ‚.
•• Search
Select and play another video in the same folder. (Search Titles)
•• Repeat Mode
Configure Repeat Mode. (Off, Repeat One, Repeat All)
•• Picture Size
Change the screen size (Picture Size). Supported screen sizes vary
depending on the image. (Original / Mode1 / Mode2 / Smart View 1 /
Smart View 2)
•• Settings
93
Available buttons and features during music playback
Pressing the E or TOOLS button displays the following buttons. The RETURN button makes the buttons disappear.
•• Pause / Play
Pause or play music.
•• Rewind / Fast Forward
Rewind or fast forward music. Speed up playback up to 3x, if required. To play the previous music file, select ∂ twice.
•• Previous / Next
To play the previous music file, select  twice. Selecting  once will play the current music from the beginning.
To play the next music file, select ‚.
•• Repeat
Configure Repeat mode. One Song plays the current music file repeatedly. All plays all files in a folder repeatedly.
•• Shuffle
Enable or disable shuffle playback mode.
•• Sound Mode
Change the Sound Mode.
94
Supported Subtitle and Media play file formats
Subtitle
External
•• MPEG-4 timed text (.ttxt)
•• SAMI (.smi)
•• SubRip (.srt)
•• SubViewer (.sub)
•• Micro DVD (.sub or .txt)
•• SubStation Alpha (.ssa)
•• Advanced SubStation Alpha (.ass)
•• Powerdivx (.psb)
Internal
•• Xsub
Container: AVI
•• SubStation Alpha
Container: MKV
•• Advanced SubStation Alpha
Container: MKV
•• SubRip
Container: MKV
•• MPEG-4 timed text
Container: MP4
Compatible image file format
Type
JPEG
4096 x 4096
MPO
BMP
95
Supported music file formats
File Extension
*.aac, *.flac, *.m4a, *.mid, *.midi,
*.mp3, *.mpa, *.ogg, *.wav, *.wma
Supported Video Formats
•• Video content will not play, or not play correctly, if there is an error in the content or the container.
•• Sound or video may not work if the contents have a standard bitrate/frame rate above the compatible Frame/sec listed in the table above.
•• If the Index Table is in error, the Seek (Jump) function is not supported.
•• You may experience file stuttering while playing a video through a network connection.
•• The menu may take longer to appear if the video’s bit rate exceeds 10Mbps.
•• Some USB/digital camera devices may not be compatible with the player.
Video Decoder
Audio Decoder
Supports up to H.264, Level 4.1
Supports up to WMA 10 Pro 5.1 channel.
H.264 FMO / ASO / RS, VC1 SP / MP / AP L4 and AVCHD are not supported.
WMA lossless audio is not supported.
For all Video codecs except MVC, VP8, VP6:
QCELP, AMR NB/WB are not supported.
•• Below 1280 x 720: 60 frame max
If Vorbis is only in Webm container, supports up to 2 channel.
•• Above 1280 x 720: 30 frame max
GMC 2 over is not supported.
Supports only BD MVC Spec.
96
Container
Video Codec
Resolution
Frame rate
(fps)
Bit rate
(Mbps)
Audio Codec
3gpp
DivX 3.11 /DivX4.X
1280 x 720
60
30
AAC
asf
avi
flv
mkv
mov
AC3
XVID
H.264 BP/MP/HP
MPEG-4 SP/ASP
mp4
ps
vro
DD+
DTS Core
HE-AAC
LPCM
WINDOW MEDIA VIDEO V9
ts
vob
ADPCM
MP3
WMA
MPEG2
MPEG1
H.263
DivX5.x
DivX6.X
97
Container
Video Codec
Resolution
Frame rate
(fps)
Bit rate
(Mbps)
Audio Codec
3gpp
DivX 3.11 /DivX4.X
1920 x 1080
30
30
AAC
asf
avi
flv
mkv
mov
mp4
AC3
XVID
ADPCM
DD+
H.264 BP/MP/HP
DTS Core
MPEG-4 SP/ASP
HE-AAC
LPCM
WINDOW MEDIA VIDEO V9
ps
ts
vob
MP3
MPEG2
WMA
MPEG1
vro
H.263
DivX5.x
DivX6.X
MOTION JPEG
640 x 480
30
8
98
Chapter 11
System
Setup
Initial settings (Setup)
After powering on the product for the first time, configure basic settings such as the language, channel and time.
MENU m → System → Setup → ENTER E
Press the
button. Setup is available only when Source is set to TV.
――The default PIN number for a new product set is “0-0-0-0”.
1
System
Press the
Setup
Menu Language
Selecting a language
English
2
Regional Settings
――The displayed image may differ depending on the model.
Eco Solution
3
Off
Channel Source
TV input source setup.
Set Channel Source to Set-top box to display the Source options.
Screen Burn Protection
Ticker
button, and then press the E button. Specify the OSD menu language.
Select your region to optimise the system.
Time
Auto Protection Time
or
-- Aerial / Set-top box / No TV(Signage Only)
Off
4
Auto Tuning
This feature automatically searches and configures broadcast signals connected to the product.
To configure settings later, press the Stop button.
-- The displayed image may differ depending on the model.
――Auto Tuning does not appear if Set-top box or No TV(Signage Only) is selected.
99
5
Network Settings
Select a wireless router from the list of retrieved routers and press the E button.
If a wireless router to connect to is not found, select the arrow on the right and press the Skip button.
6
Clock
Set the current date and time, and then select Next.
7
Auto Power Off
Set Auto Power Off option. If you select On, the display will be turned off after no user interaction is detected for 4
hours.
8
Setup Complete!
To watch TV using the product now, select OK.
100
Menu Language
Set the menu language.
――A change to the language setting will only be applied to the onscreen menu display. It will not be applied to other functions
on your PC.
MENU m → System → Menu Language → ENTER E
System
Menu Language
English
-- The displayed image may differ depending on the model.
101
Time
You can configure Clock. You can also set the product to automatically turn on or off at a specified time using the Timer
function.
MENU m → System → Time → ENTER E
Clock
Time
Clock Mode
Set the current time manually or automatically.
Clock
Sleep Timer
On Timer
Off Timer
Holiday Management
MagicInfo On/Off Timer
Off
Auto: Have the product set the current time automatically using the time from a digital channel.
――You must have the cable or an antenna connected to the product to set the time automatically.
Manual: Set the current time manually.
Clock Set
Set the clock to use the various various timer features of the product.
Set the Date and Time.
Select Clock Set. Select Date or Time, and then press E.
Use the number buttons to enter numbers or press the up and down arrow buttons. Use the left and right arrow buttons to
move from one entry field to the next. Press E when done.
――Available only when Clock Mode is set to Manual.
-- The displayed image may differ depending on the model.
――You can set the Date and Time directly by pressing the number buttons on the remote control.
Time Zone
Select your time zone.
――This function is only available when the Clock Mode is set to Auto.
102
Sleep Timer
Time
Automatically shuts off the product after a preset period of time.
Clock
Sleep Timer
Off
(Off / 30 min / 60 min / 90 min / 120 min / 150 min / 180 min)
――Use the up and down arrows to select a period of time, and then press E. To cancel Sleep Timer, select Off.
On Timer
On Timer
Off Timer
Set On Timer so that your product turns on automatically at a time and on a day of your choosing.
Holiday Management
MagicInfo On/Off Timer
-- The displayed image may differ depending on the model.
The power is turned on with the specified volume or input source.
On Timer: Set the on timer by making a selection from one of the seven options. Ensure you set the current time first.
(On Timer1 ~ On Timer7)
――You must set the clock before you can use On Timer.
•• Setup: Select Off, Once, Everyday, Mon~Fri, Mon~Sat, Sat~Sun or Manual. If you select Manual, you can choose the
days you want On Timer to turn on your product.
――The check mark indicates days you’ve selected.
•• Time: Set the hour and minute. Use the number buttons or the up and down arrow keys to enter numbers.
Use the left and right arrow buttons to change entry fields.
•• Volume: Set the desired volume level. Use the left and right arrow buttons to change the volume level.
•• Source: Select the input source of your choice.
•• Aerial (when the Source is set to TV): Select Air or Cable.
•• Channel (when the Source is set to TV): Select the desired channel.
•• Music / Photo (when the Source is set to USB): Select a folder in the USB device containing music or photo files you
want played when the product turns on automatically.
――This function is available only when a USB device is connected.
103
――If there is no music file on the USB device or you don’t select a folder containing a music file, the Timer function does not
operate correctly.
――If there is only one photo file in the USB, the Slide Show will not play.
――If a folder name is too long, the folder cannot be selected.
――Each USB you use is assigned its own folder. When using more than one of the same type of USB, make sure the folders
assigned to each USB have different names.
――We recommend that you use a USB memory stick and a multi card reader when using On Timer. The On Timer function
may not work with USB devices with a built-in battery, MP3 players, or PMPs made by some manufacturers because the
product can take too long to recognize these devices.
104
Off Timer
Time
Set the off timer (Off Timer) by making a selection from one of the seven options. (Off Timer1 ~ Off Timer7)
――You must set the clock before you can use Off Timer.
Clock
On Timer
•• Setup: Select Off, Once, Everyday, Mon~Fri, Mon~Sat, Sat~Sun or Manual. If you select Manual, you can choose the
days you want Off Timer to turn off your product.
――The check mark indicates days you’ve selected.
Off Timer
•• Time: Set the hour and minute. Use the number buttons or the up and down arrow keys to enter numbers. Use the left
and right arrow buttons to change entry fields.
Sleep Timer
Holiday Management
MagicInfo On/Off Timer
Off
Holiday Management
Timer will be disabled during a period specified as a holiday.
•• Add: Specify the period you want to add as a holiday.
Select the start and end dates of the holiday you want to add using the / buttons, and click the Save button.
-- The displayed image may differ depending on the model.
The period will be added to the list of holidays.
-- Start: Set the start date of the holiday.
-- End: Set the end date of the holiday.
-- Delete: Delete all items from the list of holidays.
Select Delete. The message "Delete all holidays?" will appear.
Select Yes. All holidays will be deleted.
•• Apply: Set the On Timer and Off Timer to not activate on public holidays.
-- Press E to select the On Timer and Off Timer settings you do not want to activate.
-- The selected On Timer and Off Timer will not activate.
105
MagicInfo On/Off Timer
Time
View the on/off timer settings configured in the MagicInfo Express tool.
Clock
Sleep Timer
On Timer
Off Timer
Holiday Management
Off
•• On Timer
-- Setup: View the days of the week specified in the MagicInfo Express tool for the on timer to turn on the product.
-- Time: View the time specified in the MagicInfo Express tool for the on timer to turn on the product.
-- Source: View the content input source specified in the MagicInfo Express tool.
•• Off Timer
-- Setup: View the days of the week specified in the MagicInfo Express tool for the off timer to turn
off the product.
-- Time: View the time specified in the MagicInfo Express tool for the off timer to turn off the product.
MagicInfo On/Off Timer
-- The displayed image may differ depending on the model.
106
Eco Solution
Energy Saving
Reduce the power consumption by adjusting the screen brightness.
MENU m → System → Eco Solution → ENTER E
Selecting Picture Off switches off the screen. The volume is not disabled.
To switch the screen on, press any button other than the volume button.
Eco Solution
•• Off / Low / Medium / High
Energy Saving
Off
Eco Sensor
Off
No Signal Power Off
15 min
Auto Power Off
-- The displayed image may differ depending on the model.
On
Eco Sensor
Eco Sensor
To enhance your power savings, the picture settings will automatically adapt to the light in the room.
•• Off / On
――Adjusting the Backlight setting under Picture while Eco Sensor is on will disable the Off.
Min. Backlight
When Eco Sensor is On, you can manually adjust the minimum screen brightness. Min. Backlight is the darkest backlight
mode. Make sure the Min. Backlight setting is lower than the Backlight setting.
――If Eco Sensor is On, the display brightness may change (become slightly darker or brighter) depending on the surrounding
light intensity.
107
No Signal Power Off
Eco Solution
Save power by turning the device off when no signal is received from any source.
Energy Saving
Off
Eco Sensor
Off
No Signal Power Off
15 min
Auto Power Off
-- The displayed image may differ depending on the model.
On
•• Off / 15 min / 30 min / 60 min
――Disabled when an attached PC is in power saving mode.
――This product is set to 15 min by default.
――The product will automatically power off at a specified time. The time can be changed as required.
Auto Power Off
The product will automatically turn off if you don’t press a button on the remote or touch a button on product front panel
within 4 hours to prevent overheating.
•• Off / On
――The off timer can be set within a range of 1 to 23 hours. The product will automatically power off after the specified number
of hours.
――This option is only available when Auto Power Off is set to On.
――For products for the market in some regions, the Auto Power Off is set to automatically activate 4 hours after the product
powers on. This is done in accordance with power supply regulations. If you do not want the timer to activate, go to
MENU m → System → Eco Solution and set Auto Power Off to Off.
108
Auto Protection Time
If the screen displays a still image for a certain period of time you define, the product activates the screen saver to prevent the
formation of burnt in ghost images on the screen.
――Displaying a still image for longer than four hours can cause image retention.
MENU m → System → Auto Protection Time → ENTER E
•• Off / 2 hours / 4 hours / 8 hours / 10 hours
System
Auto Protection Time
Off
-- The displayed image may differ depending on the model.
109
Screen Burn Protection
MENU m → System → Screen Burn Protection → ENTER E
To reduce the possibility of screen burn, this unit is equipped with Pixel Shift screen burn prevention technology.
Pixel Shift moves the picture slightly on the screen.
The Pixel Shift Time setting allows you to programme the time between movements of the picture in minutes.
Pixel Shift
Screen Burn Protection
Minimize image retention by finely moving pixels horizontally or vertically.
Pixel Shift
Off
Timer
Off
Immediate display
Off
Side Grey
Off
•• Pixel Shift (Off / On)
-- Horizontal: Sets how many pixels the screen moves horizontally.
-- Vertical: Sets how many pixels the screen moves vertically.
-- Time: Set the time interval for performing the horizontal or vertical movement, respectively.
――Horizontal, Vertical and Time are enabled only when Pixel Shift is set to On.
Available Pixel Shift Settings and Optimum Settings.
Available Settings
-- The displayed image may differ depending on the model.
Optimum Settings
Horizontal (pixels)
0~4
4
Vertical (pixels)
0~4
4
Time (minute)
1 min ~ 4 min
4 min
――The Pixel Shift value may differ depending on the product size (inches) and mode.
――Displaying a still image or a 4:3 output for an extended period of time may cause image retention. This is not a defect in the
product.
――This function is not available in the Screen Fit mode.
110
Timer
Screen Burn Protection
You can set the timer for Screen Burn Protection.
Pixel Shift
Off
The Timer feature stops automatically after a specified period of time.
Timer
Off
Timer
Immediate display
Off
•• Off
Side Grey
Off
•• Repeat: Display the image retention-preventive pattern set in Mode at specified time intervals(Period).
•• Interval: Display the image retention-preventive pattern set in Mode for a specified period of time (from Start Time to
End Time).
――The option is enabled only when Clock Set is configured.
――Mode, Period, Time, Start Time and End Time are enabled only when Timer is set to Repeat or Interval.
-- The displayed image may differ depending on the model.
Mode
Select a screen protective pattern to display.
•• Pixel: Pixels on the screen alternate black continuously.
•• Rolling bar: A vertical bar moves left to right.
•• Fading screen: The entire screen becomes brighter, then darker.
――The Rolling bar and Fading screen patterns appear only once regardless of the specified repeat period or time.
Period
Specify the time interval to activate the Screen Burn Protection function.
――The option is enabled when Repeat is selected for Timer.
Time
Specify the duration to keep the Screen Burn Protection function on.
――The option is enabled when Pixel is selected for Mode.
111
Start Time
Set the start time to activate the screen protection function.
――The option is enabled when Interval is selected for Timer.
End Time
Set the end time to deactivate the screen protection function.
――The option is enabled when Interval is selected for Timer.
112
Immediate display
Screen Burn Protection
Select the screen saver you want to display immediately.
Pixel Shift
Off
Timer
Off
Immediate display
Off
Side Grey
Off
•• Off / Pixel / Rolling bar / Fading screen
Side Grey
When the screen is set to 4:3 aspect ratio, adjust the brightness of white margins on sides to protect the screen.
•• Off / Light / Dark
-- The displayed image may differ depending on the model.
113
Ticker
Ticker
Input text while a video or image is displayed and display the text on the screen.
MENU m → System → Ticker → ENTER E
•• Off / On
――Message, Time, Position, Motion, and Font options are enabled only when Ticker is set to On.
Ticker
Ticker
Message
Off
· Message
Time
· Time
Set the Start Time and End Time to display a Message.
•• Start Time
· Position
· Motion
Enter a message to display on the screen.
•• End Time
Off
· Font Style
Position
Select an orientation to display a Message from Horizontal and Vertical.
•• Horizontal (Left / Centre / Right)
•• Vertical (Up / Middle / Down)
-- The displayed image may differ depending on the model.
-- The Ticker function is only available when Menu Language is set to English.
Motion
Specify the Direction and Speed to display a Message.
•• Motion (Off / On)
•• Direction (Left / Right / Up / Down)
•• Speed (Slow / Normal / Fast)
――Direction and Speed are enabled only when Motion is set to On.
Font Style
Configure the message font options.
114
Source AutoSwitch Settings
Turning on the display with Source AutoSwitch On, and the previous video source selection is not active, the display will
automatically search the different video input sources for active video.
MENU m → System → Source AutoSwitch Settings → ENTER E
Source AutoSwitch
When the Source AutoSwitch is On, the display video source will automatically be searched for active video.
Source AutoSwitch Settings
The Primary Source selection will be activated, if the current video source is not recognized.
Source AutoSwitch
Off
· Primary Source Recovery
Off
· Primary Source
All
· Secondary Source
HDMI1
Secondary Source selection will become active, if no primary video source is available.
If both the primary and secondary input sources are not recognized, the display will perform two searches for an active source,
each search checking the primary and then secondary source. If both searches fail, the display will return to the first video
source and display a message indicating that there is no signal.
When the Primary Source selection is set to All, the display will search all the video source inputs twice in sequence looking
for an active video source, returning back to the first video source in the sequence if no video is found.
Primary Source Recovery
-- The displayed image may differ depending on the model.
Select whether to restore the selected primary input source when a primary input source is connected.
――The Primary Source Recovery function is disabled if Primary Source is set to All.
Primary Source
Specify Primary Source for the automatic input source.
Secondary Source
Specify Secondary Source for the automatic input source.
115
General
Game Mode
When connecting to a game console such as PlayStation™ or Xbox™, you can enjoy a more realistic gaming experience by
selecting game mode.
MENU m → System → General → ENTER E
•• Off / On
――Precautions and limitations for Game Mode
General
To disconnect the game console and connect another external device, set Game Mode to Off in the setup menu.
――Game Mode is not available when the input source is set to TV. After connecting the game console, set Game Mode to
Game Mode
Off
Auto Power
Off
Safety Lock
Off
Button Lock
Off
Auto Power
USB Auto Play Lock
Off
Enabling this option will automatically power on the product if the power cable is connected.
Standby Control
Auto
Lamp Schedule
Off
On. Unfortunately, you may notice reduced picture quality.
――If Game Mode is On
Picture Mode is set to Standard and Sound Mode is set to Movie.
•• Off / On
Safety Lock
It sets safe lock function.
•• Off / On
-- The displayed image may differ depending on the model.
116
Button Lock
General
It sets safe lock function.
Button Lock
Off
USB Auto Play Lock
Off
Standby Control
Auto
Lamp Schedule
Off
OSD Display
•• Off / On
This menu can be used to lock the buttons on the product.
Only the remote control can control the product if Button Lock is set to On.
USB Auto Play Lock
Select whether to automatically play MagicInfo content saved on a connected USB device.
•• On
Do not play MagicInfo content saved on the USB device automatically.
――Connecting a USB device containing MagicInfo content displays "USB Auto Play Lock : On" for five seconds.
-- The displayed image may differ depending on the model.
•• Off
Play MagicInfo content saved on the USB device automatically.
Standby Control
You can set the screen standby mode to be applied when an input signal is received.
•• Auto
Power-saving mode will activate if no input signals are detected even though a source device is connected to the display.
The message No Signal will appear if no source device is connected.
•• On
Power-saving mode will activate if no input signals are detected.
•• Off
The message No Signal will appear if no input signals are detected.
――The Standby Control option is only enabled when Source is set to HDMI1, HDMI2.
――If No Signal is displayed although a source device is connected, check the cable connection.
117
Lamp Schedule
General
Adjusts the luminance to a user-specified value at a specified time.
Button Lock
Off
USB Auto Play Lock
Off
Standby Control
Auto
Lamp Schedule
Off
OSD Display
•• Off / On
OSD Display
Displays or hides a menu item on the screen.
•• Source OSD: Off / On
•• No Signal OSD: Off / On
-- The displayed image may differ depending on the model.
118
Change PIN
MENU m → System → Change PIN → ENTER E
The Change PIN screen will appear.
Choose any 4 digits for your PIN and enter it in Enter New PIN. Reenter the same 4 digits in Confirm New PIN.
When the Confirm screen disappears, press the Close button. The product has memorized your new PIN.
――Default password: 0 - 0 - 0 - 0
System
Change PIN
-- The displayed image may differ depending on the model.
119
Clone Product
MENU m → System → Clone Product → ENTER E
Clone Product
Clone to USB
Clone From USB
Export the product settings to a USB device or load the settings via a USB device.
This option is useful when assigning the same settings to several products.
•• Clone to USB: Copy the product settings to a USB device.
•• Clone From USB: Assign the settings saved in a USB device to the product.
-- After configuration is complete, the product is rebooted automatically.
――The option may not work properly if the USB device contains a file other than a settings file.
――Confirm that the USB device functions properly before running the option.
――The option is available for products with the same Model Code and Software Version.
Go to Support → Contact Samsung and find the product Model Code and Software Version.
-- The displayed image may differ depending on the model.
Reset System
This option returns the current settings under system to the default factory settings.
MENU m → System → Reset System → ENTER E
System
Reset System
-- The displayed image may differ depending on the model.
120
Reset All
This option returns all the current settings for a display to the default factory settings.
MENU m → System → Reset All → ENTER E
System
Reset All
-- The displayed image may differ depending on the model.
DivX® Video On Demand
MENU m → System → DivX® Video On Demand → ENTER E
Shows the registration code authorized for the product.
If you connect to the DivXⓇ web site and register using that code, you can download the VOD registration file.
For more information about DivXⓇ VOD, visit “http://vod.divx.com”.
System
DivX® Video On Demand
-- The displayed image may differ depending on the model.
121
Chapter 12
Support
Software Update
Current Version: This is the software
version already installed in the product.
MENU m → Support → Software Update → ENTER E
The Software Update menu lets you upgrade your product software to the latest version.
――Be careful not to turn off the power until the upgrade is complete. The product will turn off and on automatically after completing the software upgrade.
――When you upgrade software, all video and audio settings you have made will return to their default settings. We advise you to write down your settings so that you can
easily reset them after the upgrade.
Update now
Update the software to the latest version.
――Performing a software update via USB will display the corresponding update window after a maximum of two minutes.
Use Mode
MENU m → Support → Use Mode → ENTER E
Select the appropriate mode according to where the product is used.
If you choose Demo Mode, the demo content will be played automatically and the picture settings will be reset in 5 minutes after change.
•• Standard Use / Demo Mode
122
Contact Samsung
MENU m → Support → Contact Samsung → ENTER E
View this information when your product does not work properly or when you want to upgrade the software.
You can find information regarding our call centres and how to download products and software.
――Contact Samsung and find the product Model Code and Software Version.
123
Chapter 13
Troubleshooting Guide
Requirements Before Contacting Samsung Customer Service Centre
Before calling Samsung Customer Service
Centre, test your product as follows. If
the problem persists, contact Samsung
Customer Service Centre.
If the screen remains blank, check the PC
system, video controller and cable.
Testing the Product
Check if your product is operating normally by using the product test function.
If the screen remains blank while the power LED blinks even when the product is correctly connected to a PC, perform product testing.
1
Power off both the PC and product.
2
Disconnect all the cables from the product.
3
Power on the product.
4
If No Signal is displayed, the product is operating normally.
Checking the Resolution and Frequency
Not Optimum Mode will briefly be displayed if a mode that exceeds a supported resolution is selected (refer to Supported Resolutions).
124
Check the followings.
Installation issue (PC mode)
The screen keeps switching on and off.
Check the cable connection between the product and PC, and ensure the connection is secure.
Blank spaces are found on all four sides of the screen when
an HDMI or HDMI-DVI cable is connected to the product and
PC.
The blank spaces found on the screen have nothing to do with the product.
Blank spaces on the screen are caused by the PC or graphics card. To resolve the problem, adjust the
screen size in the HDMI or DVI settings for the graphics card.
If the graphics card settings menu does not have an option to adjust the screen size, update the
graphics card driver to the latest version.
(Please contact the graphics card or computer manufacturer for further details about how to adjust
the screen settings.)
Screen issue
The power LED is off. The screen will not switch on.
Make sure that the power cord is connected.
No Cable Connected is displayed on the screen (refer to
"Connecting to a PC").
Check that the product is connected correctly with a cable.
Not Optimum Mode is displayed.
This message is displayed when a signal from the graphics card exceeds the product's maximum
resolution and frequency.
Check that the device connected to the product is powered on.
Refer to the Standard Signal Mode Table and set the maximum resolution and frequency according to
the product specifications.
The images on the screen look distorted.
Check the cable connection to the product
125
Screen issue
The screen is not clear. The screen is blurry.
Adjust Coarse and Fine.
Remove any accessories (video extension cable, etc) and try again.
Set the resolution and frequency to the recommended level.
The screen appears unstable and shaky.
There are shadows or ghost images left on the screen.
Check that the resolution and frequency of the PC and graphics card are set within a range compatible
with the product. Then, change the screen settings if required by referring to the Additional
Information on the product menu and the Standard Signal Mode Table.
The screen is too bright. The screen is too dark.
Adjust Brightness and Contrast.
Screen colour is inconsistent.
Go to Picture and adjust the Colour Space settings.
White does not really look white.
Go to Picture and adjust the White Balance settings.
There is no image on the screen and the power LED blinks
every 0.5 to 1 second.
The product is in power-saving mode.
The product will turn off automatically.
Go to System and make sure Sleep Timer is set to Off.
Press any key on the keyboard or move the mouse to return to the previous screen.
If a PC is connected to the product, check the power status of the PC.
Make sure the power cable is connected properly to the product and power outlet.
If the signal from a connected device is not detected, the product automatically turns off after 10 to 15
minutes.
Picture quality of the product is different from the dealer
shop where it was purchased.
Use an HDMI cable to obtain high-definition (HD) picture quality.
126
Screen issue
The screen display does not look normal.
Encoded video content may cause the display to appear corrupted in scenes featuring fast moving
objects such as in a sports event or action video.
Low signal level or low picture quality may cause the display to appear corrupted. This does not mean
the product is defective.
A cell phone within a distance of one-meter radius may cause static on analogue and digital products.
The brightness and colour do not look normal.
Go to Picture and adjust the screen settings such as Picture Mode, Colour, Brightness and
Sharpness.
Go to System and adjust the Eco Solution settings.
Reset the screen settings to the default settings.
Broken lines are displayed on the edges of the screen.
If Picture Size is set to Screen Fit, change the setting to 16:9.
Lines (red, green or blue) are displayed on the screen.
These lines are displayed when there is a defect in DATA SOURCE DRIVER IC on the SMART Signage TV.
Contact a Samsung Service Centre to resolve the issue.
The display looks unstable and then freezes.
The screen may freeze when a resolution other than the recommended resolution is used or if the
signal is not stable. To resolve the issue, change the PC resolution to the recommended resolution.
The screen cannot be displayed in full screen.
A scaled SD (4:3) content file can cause black bars on both sides of an HD channel screen.
A video with an aspect ratio different from the product can cause black bars at the top and bottom of
the screen.
Change the screen size setting to full screen on the product or source device.
Sound issue
There is no sound.
Check the connection of the audio cable or adjust the volume.
Check the volume.
127
Sound issue
The volume is too low.
Adjust the volume.
If the volume is still low after turning it up to the maximum level, adjust the volume on your PC sound
card or software programme.
Video is available but there is no sound.
If an HDMI cable is connected, check the audio output settings on the PC.
Go to Sound and change Speaker Select to Internal.
If a source device is used
•• Make sure the audio cable is properly connected to the audio input port on the product.
•• Check the audio output settings for the source device.
(For example, if an HDMI cable is connected to the SMART Signage TV, the audio setting for the
cable box may need to be changed to HDMI.)
If the product has a headphone port, make sure nothing is connected to it.
Reconnect the power cable to the device and then reboot the device.
There is static coming from the speakers.
Check the cable connection. Make sure a video cable is not connected to an audio input port.
Check the signal strength after connecting a cable.
Low signal level can cause corrupted sound.
There is audible sound when the volume is muted.
When Speaker Select is set to External, the volume button and mute function are disabled.
Adjust the volume for the external speakers.
Audio settings for main speakers are separate from the internal speakers on the product.
Changing or muting the volume on the product does not affect an external amplifier(decoder).
Sound from the SMART Signage TV does not change after
Sound Mode is changed.
Audio settings for main speakers are separate from the internal speakers on the product.
Audio settings on a source device do not affect the internal speaker settings on the product.
128
Sound issue
There is an echo sound coming from the speakers.
When the built-in speakers are turned on, the built-in and external speakers make sound
simultaneously. This may cause an echo effect due to different decoding rates between these two
types of speakers. If this is the case, set Speaker Select to External.
Remote control issue
The remote control does not work.
Make sure that the batteries are correctly in place (+/-).
Check if the batteries are flat.
Check for power failure.
Make sure that the power cord is connected.
Check for any special lighting or neon signs switched on in the vicinity.
Source device issue
A beeping sound is heard when my PC is booting.
If a beeping sound is heard when your PC is booting, have your PC serviced.
Other issue
The product smells like plastic.
The plastic smell is normal and disappears over time.
The product appears tilted.
Remove and then attach the stand again to the product.
Audio or video cuts out intermittently.
Check the cable connection and connect it again if required.
Using a very hard or thick cable may corrupt audio and video files.
Make sure cables are flexible enough to ensure durability. When mounting the product onto a wall, it
is recommended to use right-angle cables.
Small particles are found on the edges of the product.
The particles are part of the product design. The product is not defective.
129
Other issue
The PIP menu is not available.
The menu is enabled or disabled depending on the Source mode.
When I try to change the PC resolution, a message The
defined resolution is not supported. appears.
The message The defined resolution is not supported. appears if the input source resolution
exceeds the maximum resolution of the display.
To resolve the issue, change the PC resolution to a resolution supported on the display.
There is no sound from the speakers in HDMI mode when a
DVI-HDMI cable is connected.
DVI cables do not transmit sound data.
HDMI Black Level is not functioning properly on an HDMI
device with YCbCr output.
This function is available only when a source device, such as a DVD player and STB, is connected to the
product via an HDMI (RGB signal) cable.
There is no sound in HDMI mode.
Displayed picture colours may not look normal. Video or sound may not be available. This can occur if
a source device that only supports an older version of the HDMI standard is connected to the product.
If these issues occur, connect an audio cable along with the HDMI cable.
Make sure to connect the audio cable to the correct input jack to enable audio.
Some PC graphics cards may not automatically recognize HDMI signals that do not include sound. In
this case, manually select a sound input.
PC
Sound input
Screen mode
Auto
PC settings
130
Q&A
Question
Refer to the user manual for your PC or
graphics card for further instructions on
adjustment.
How can I change the frequency?
Answer
Set the frequency on your graphics card.
•• Windows XP: Go to Control Panel → Appearance and Themes → Display → Settings →
Advanced → Monitor and adjust the frequency in Monitor Settings.
•• Windows ME/2000: Go to Control Panel → Display → Settings → Advanced → Monitor and
adjust the frequency in Monitor Settings.
•• Windows Vista: Go to Control Panel → Appearance and Personalization → Personalize →
Display Settings → Advanced Settings → Monitor and adjust the frequency in Monitor
Settings.
•• Windows 7: Go to Control Panel → Appearance and Personalization → Display → Adjust
resolution → Advanced Settings → Monitor and adjust the frequency in Monitor Settings.
•• Windows 8: Go to Settings → Control Panel → Appearance and Personalization → Display
→ Adjust resolution → Advanced Settings → Monitor and adjust the frequency in Monitor
Settings.
How can I change the resolution?
•• Windows XP: Go to Control Panel → Appearance and Themes → Display → Settings and
adjust the resolution.
•• Windows ME/2000: Go to Control Panel → Display → Settings and adjust the resolution.
•• Windows Vista: Go to Control Panel → Appearance and Personalization → Personalize →
Display Settings and adjust the resolution.
•• Windows 7: Go to Control Panel → Appearance and Personalization → Display → Adjust
Resolution and adjust the resolution.
•• Windows 8: Go to Settings → Control Panel → Appearance and Personalization → Display
→ Adjust Resolution and adjust the resolution.
131
Question
How do I set powersaving mode?
Answer
•• Windows XP: Set power-saving mode in Control Panel → Appearance and Themes → Display
→ Screen Saver Settings or BIOS SETUP on the PC.
•• Windows ME/2000: Set power-saving mode in Control Panel → Display → Screen Saver
Settings or BIOS SETUP on the PC.
•• Windows Vista: Set power-saving mode in Control Panel → Appearance and Personalization
→ Personalize → Screen Saver Settings or BIOS SETUP on the PC.
•• Windows 7: Set power-saving mode in Control Panel → Appearance and Personalization →
Personalize → Screen Saver Settings or BIOS SETUP on the PC.
•• Windows 8: Set power-saving mode in Settings → Control Panel → Appearance and
Personalization → Personalize → Screen Saver Settings or BIOS SETUP on the PC.
132
Chapter 14
Specifications
General
- Size
Model Name
Panel
RM40D
Size
40 CLASS (40.0 inches / 101 cm)
48 CLASS (47.6 inches / 121 cm)
Display area
885.6 mm (H) x 498.15 mm (V)
1054.08 mm (H) x 592.92 mm (V)
34.87 inches (H) x 19.61 inches (V)
41.50 inches (H) x 23.34 inches (V)
906.6 x 532.9 x 65.1 mm / 7.6 kg
1075.1 x 627.6 x 65.5 mm / 11.1 kg
35.69 x 20.98 x 2.56 inches / 16.76 Ibs
42.33 x 24.71 x 2.58 inches / 24.47 Ibs
906.6 x 578.2 x 196.4 mm / 8.6 kg
1075.1 x 673.8 x 203.9 mm / 12.3 kg
35.69 x 22.76 x 7.73 inches / 18.96 Ibs
42.33 x 26.53 x 8.03 inches / 27.12 Ibs
- Display area
H
Dimensions
(W x H x D /
Weight)
V
Without Stand
With Stand
- Dimensions (W x H x D)
RM48D
Audio Output
10 W + 10 W
Power Supply
AC 100 to 240 VAC (+/- 10%), 60 / 50Hz ± 3Hz
Refer to the label at the back of the product as the standard voltage can vary in different countries.
D
Environmental
considerations
H
W
Operating
Temperature : 32 F ~ 104 F (0 C ~ 40 C)
Humidity : 10 % ~ 80 %, non-condensing
Storage
Temperature : -4 F ~ 113 F (-20 C ~ 45 C)
Humidity : 5 % ~ 95 %, non-condensing
133
――Plug-and-Play
This SMART Signage TV can be installed and used with any Plug-and-Play compatible systems.
Two-way data exchange between the SMART Signage TV and PC system optimizes the SMART Signage TV settings.
SMART Signage TV installation takes place automatically. However, you can customize the installation settings if desired.
――Due to the nature of the manufacturing of this product, approximately 1 pixel per million (1ppm) may appear brighter or darker on the panel. This does not affect
product performance.
――This device is a Class A digital apparatus.
[Recommendation] - EU Only
•• Hereby, Samsung Electronics, declares that this Monitor is in compliance with the essential requirements and other
relevant provisions of Directive 1999/5/EC.
•• The official Declaration of Conformity may be found at http://www.samsung.com/displaysolutions, go to Support >
Search Product Support and enter the model name.
•• This equipment may only be used indoors.
•• This equipment may be operated in all EU countries.
134
Power Consumption
Normal Operation
Typical
Power Indicator
Power Consumption
Stand-by
Rating
Max
Off
On
RM40D
37 W
89 W
98 W
RM48D
45 W
104 W
114 W
0.5 W
――The displayed power consumption level can vary in different operating conditions or when settings are changed.
――SOG(Sync On Green) is not supported.
――To reduce the power consumption to 0, disconnect the power cord. Disconnect the power cable if you will not be using the product for an extended period of time (during
vacation, etc.)
135
Preset Timing Modes
――This product can be set to only one resolution for each screen size to obtain the optimum picture quality due to the nature of the panel. Using a resolution other than
the specified resolution may degrade the picture quality. To avoid this, it is recommended that you select the optimum resolution specified for your product.
――Check the frequency when you exchange a CDT product (connected to a PC) for an LCD product. If the LCD product does not support 85Hz, change the vertical
frequency to 60Hz using the CDT product before you exchange it with the LCD product.
Model Name
Synchronization
Resolution
-- Horizontal Frequency
The time required to scan a single line
from the left to the right side of the
screen is called a horizontal cycle. The
reciprocal number of a horizontal cycle
is called horizontal frequency. Horizontal
frequency is measured in kHz.
-- Vertical Frequency
The product displays a single image
multiple times per second (like a
fluorescent light) to display what the
viewer sees. The rate of a single image
being displayed repeatedly per second is
called vertical frequency or refresh rate.
Vertical frequency is measured in Hz.
RM40D
RM48D
Horizontal Frequency
30 ~ 81 kHz
Vertical Frequency
48 ~ 75 Hz
Optimum resolution
1920 x 1080 @ 60 Hz
Maximum resolution
1920 x 1080 @ 60 Hz
The screen will automatically be adjusted if a signal that belongs to the following standard signal modes is transmitted from your PC. If the signal transmitted from the PC
does not belong to the standard signal modes, the screen may be blank with the power LED on. In such a case, change the settings according to the following table by
referring to the graphics card user manual.
――PC mode is not support interlaced signal.
Resolution
Horizontal Frequency
(kHz)
Vertical Frequency
(Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
VESA, 640 x 480
31.469
59.940
25.175
-/-
IBM, 720 x 400
31.469
70.087
28.322
-/+
MAC, 640 x 480
35.000
66.667
30.240
-/-
MAC, 832 x 624
49.726
74.551
57.284
-/-
MAC, 1152 x 870
68.681
75.062
100.000
-/-
VESA, 640 x 480
37.861
72.809
31.500
-/-
136
Resolution
Horizontal Frequency
(kHz)
Vertical Frequency
(Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
VESA, 640 x 480
37.500
75.000
31.500
-/-
VESA, 800 x 600
37.879
60.317
40.000
+/+
VESA, 800 x 600
48.077
72.188
50.000
+/+
VESA, 800 x 600
46.875
75.000
49.500
+/+
VESA, 1024 x 768
48.363
60.004
65.000
-/-
VESA, 1024 x 768
56.476
70.069
75.000
-/-
VESA, 1024 x 768
60.023
75.029
78.750
+/+
VESA, 1152 x 864
67.500
75.000
108.000
+/+
VESA, 1280 x 720
45.000
60.000
74.250
+/+
VESA, 1280 x 800
49.702
59.810
83.500
-/+
VESA, 1280 x 1024
63.981
60.020
108.000
+/+
VESA, 1280 x 1024
79.976
75.025
135.000
+/+
VESA, 1366 x 768
47.712
59.790
85.500
+/+
VESA, 1440 x 900
55.935
59.887
106.500
-/+
VESA, 1600 x 900
60.000
60.000
108.000
+/+
VESA, 1680 x 1050
65.290
59.954
146.250
-/+
VESA, 1920 x 1080
67.500
60.000
148.500
+/+
137
Chapter 15
Appendix
Contact SAMSUNG WORLD WIDE
Web site: http://www.samsung.com/displaysolutions/signagetv
――If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care centre.
NORTH AMERICA
U.S.A
1-800-SAMSUNG (726-7864)
CANADA
1-800-SAMSUNG (726-7864)
LATIN AMERICA
ARGENTINE
0800-333-3733
BOLIVIA
800-10-7260
BRAZIL
CHILE
COLOMBIA
0800-124-421 (Demais cidades e regiões)
4004-0000 (Capitais e grandes centros)
800-SAMSUNG (726-7864)
Bogotá 600 12 72
Gratis desde cualquier parte del país 01 8000 112 112 ó desde su celular #SAM(726)
138
LATIN AMERICA
COSTA RICA
DOMINICA
ECUADOR
EL SALVADOR
GUATEMALA
HONDURAS
JAMAICA
0-800-507-7267
00-800-1-SAMSUNG (726-7864)
1-800-751-2676
1-800-10-72670
1-800-SAMSUNG (72-6786)
800-6225
1-800-299-0013
1-800-299-0033
800-27919267
800-2791-9111
1-800-234-7267
1-800-SAMSUNG (726-7864)
MEXICO
01-800-SAMSUNG (726-7864)
NICARAGUA
001-800-5077267
PANAMA
800-7267
800-0101
PARAGUAY
009-800-542-0001
PERU
0-800-777-08
PUERTO RICO
1-800-682-3180
TRINIDAD & TOBAGO
1-800-SAMSUNG (726-7864)
URUGUAY
000-405-437-33
139
LATIN AMERICA
VENEZUELA
0-800-SAMSUNG (726-7864)
EUROPE
AUSTRIA
0800 112233
BELGIUM
02 201 2418
BOSNIA
055 233 999
BULGARIA
0800 111 31
CROATIA
072 726 786
CYPRUS
8009 4000 only from landline, toll free
800 726 786
CZECH
Samsung Electronics Czech and Slovak, s.r.o. V Parku 2343/24, 148 00 - Praha 4
DENMARK
70 70 19 70
EIRE
0818 717100
ESTONIA
800 7267
FINLAND
030-6227 515
FRANCE
0825 022 062
GERMANY
0180 6 421521
GREECE
80011 – SAMSUNG (7267864)
140
EUROPE
HUNGARY
06 40 985 985
ITALIA
800 154 154 LATVIA
80007267
LITHUANIA
8800 77777
LUXEMBURG
2601 3710
MONTENEGRO
20405888
NETHERLANDS
0900-SAMSUNG (726-7864)
NORWAY
815 56480
POLAND
0 801 172 678 *(801 1Samsung)
PORTUGAL
808207267
ROMANIA
08008 726 78 64 SERBIA
381 11 321 6899
0700 726 7864
SLOVAKIA
0800 726 786
SLOVENIA
080 69 7267
SPAIN
902 879 081
SWEDEN
0771400300 SWITZERLAND
8007267864
141
EUROPE
U.K
0330 SAMCORP (7262677)
CIS
ARMENIA
0-800-05555
AZERBAIJAN
0-88-555-55-55
BELARUS
8-800-555-55-33
GEORGIA
0-800-555-555
KAZAKHSTAN
8-10-800-500-55-500 (GSM:7799)
KYRGYZSTAN
00-800-500-55-500
MOLDOVA
0-800-61440
MONGOLIA
+7-800-555-55-55
RUSSIA
8-800-555-55-33
TAJIKISTAN
8-10-800-500-55-500
UKRAINE
0-800-500777
UZBEKISTAN
8-10-800-500-55-500
142
CHINA
CHINA
400-610-5858
HONG KONG
+852-3698-4688
MACAU
0800 333
S.E.A
AUSTRALIA
1800 91 92 93
INDONESIA
0800-112-8888
JAPAN
0120-363-905
MALAYSIA
1800 88 3399
MYANMAR
+951 2399 888
NEW ZEALAND
0800726786 option 3
PHILIPPINES
632 214 77 18
SINGAPORE
+65 64150798
TAIWAN
0809-005-237
THAILAND
+662 6893277
VIETNAM
1800 588 890
143
S.W.A
BANGLADESH
0800-112-8888
INDIA
1800 3010 8282
SRI LANKA
0094117540540
0094115900000
MENA
ALGERIA
021 36 11 00
BAHRAIN
8000-4726
EGYPT
08000-726786 and 16580
IRAN
021-8255
JORDAN
06 5777441 (B2B)
KUWAIT
183-2255 (183-CALL)
MOROCCO
+ 212 522586969
OMAN
800-SAMSUNG (726-7864)
PAKISTAN
0800-Samsung (72678)
QATAR
800-2255 (800-CALL)
SAUDI ARABIA
920021230
SYRIA
18252273
144
MENA
TUNISIA
920021230
TURKEY
0850 2010 222
U.A.E
800-SAMB2B (726-222)
AFRICA
ANGOLA
917267864
BOTSWANA
8007260000
BURUNDI
200
CAMEROON
7095 0077
COTE D’ IVOIRE
8000 0077
DRC
499 999
GHANA
0800-10077 / 0302-200077
KENYA
0800 545 545
MOZAMBIQUE
847267864
827267864
NAMIBIA
8197267864
NIGERIA
0800-726-7864
RWANDA
99 99
145
AFRICA
SENEGAL
800-00-0077
SOUTH AFRICA
860 726 222
SUDAN
1969
TANZANIA
0800 755 755
UGANDA
0800 300 300
ZAMBIA
211350370
146
Responsibility for the Pay Service
(Cost to Customers)
――When the service is requested, in spite of in warranty, we may charge you for a visit from a service
technician in the following cases.
Not a product defect
Cleaning of the product, Adjustment, Explanation, Re-installation and etc.
•• If a service technician gives instructions on how to use product or simply adjusts options without
disassembling product.
•• If a defect is caused by external environmental factors (Internet, Antenna, Wired Signal, etc.)
•• If a product is reinstalled or devices are connected additionally after installing the purchased product
for the first time.
•• If a product is reinstalled to move to a different spot or to move to a different house.
•• If customer requests instructions on how to use because of another company's product.
•• If customer requests instructions on how to use the network or another company's programme.
•• If customer requests software installation and setup for the product.
A Product damage caused by customer's fault
Product damage caused by customer's mishandling or wrong repair
If a product damage is caused by;
•• External impact or drop.
•• Use of supplies or separatly sold product unspecified by Samsung.
•• Repair from a person besides an engineer of outsourcing service company or partner of Samsung
Electronics Co., Ltd.
•• Remodeling or repairing the product by customer.
•• Using it with incorrect voltage or non-authorised electrical connections.
•• Not following the "cautions" in User Manual.
Others
•• If product fails by natural disaster. (lightning, fire, earthquake, flood damage, etc)
•• If consumable components are all used up.
(Battery, Toner, Fluorescent lights, Head, Vibrator, Lamp, Filter, Ribbon, etc.)
――If customer requests a service in case the product has no defect, service fee may be charged.
So please read User Manual first.
•• If a service technician removes/cleans dusts or foreign materials inside of the product.
•• If customer requests an installation additionally after purchasing a product through home-shopping
or online.
147
WEEE
Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
(Applicable in countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB
cable) should not be disposed of with other household waste at the end of their working life.
To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from
other types of waste and recycle them responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government office, for details of
where and how they can take these items for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract. This product and its
electronic accessories should not be mixed with other commercial wastes for disposal.
Correct disposal of batteries in this product
(Applicable in countries with separate collection systems)
This marking on the battery, manual or packaging indicates that the batteries in this product should not be disposed of with other
household waste at the end of their working life. Where marked, the chemical symbols Hg, Cd or Pb indicate that the battery contains
mercury, cadmium or lead above the reference levels in EC Directive 2006/66.
If batteries are not properly disposed of, these substances can cause harm to human health or the environment.
To protect natural resources and to promote material reuse, please separate batteries from other types of waste and recycle them
through your local, free battery return system.
148
Optimum Picture Quality and Afterimage
Burn-in Prevention
Black Matrix
Common
Electrode (ITO)
Colour-Filter
Optimum Picture Quality
Due to the nature of the manufacturing of this product, approximately 1 pixel per million (1ppm) may be
brighter or darker on the panel.
This does not affect product performance.
-- The number of sub-pixels by panel type: 6,220,800
Source
Drain
•• Leaving the screen fixed on a stationary image for an extended period of time may cause afterimage
burn-in or defective pixels.
Prevention of Afterimage Burn-in
What is afterimage burn-in?
Gate
TFT
Pixel Electrode (ITO)
Storage
Capaccitor (Cs)
Data Bus-Line
Afterimage burn-in should not occur when the LCD panel is operating normally. Normal operation refers
to a continuously changing video pattern. If the LCD panel displays a fixed pattern for an extended period
of time (more than 12 hours), a slight voltage difference may occur between the electrodes in pixels that
control the liquid crystals.
Such a voltage difference between electrodes increases with time and makes the liquid crystals thinner.
When this occurs, a previous image can remain on the screen when the pattern changes. To prevent this,
the accumulated voltage difference should be reduced.
――Afterimage burn-in should not occur when an LCD panel is operating in proper conditions.
149
Preventing afterimage burn-in
――The best way to protect the product from afterimage burn-in is switching the power off or setting the
PC or system to run a screen saver when not in use. Also, Warranty service may be limited depending
on instruction guide.
•• Powering Off, Screen Saver and Power Saving Mode
-- Go to Display Properties > Power Supply on your PC and set the product to power off as
required.
-- Using a screen saver is recommended.
It is best to use a single-colour or moving-image screen saver.
•• Regular colour Change
-- Use 2 colours
Switch between 2 colours every 30 minutes as shown above.
Type 1
•• Regular Text colour Change
-- Use bright colours of similar brightness.
Interval: Change text colour and background colour every 30 minutes
FLIGHT : TIME
OZ348
: 20:30
FLIGHT : TIME
OZ348
: 20:30
FLIGHT : TIME
OZ348
: 20:30
FLIGHT : TIME
OZ348
: 20:30
-- Move and change text every 30 minutes as shown below.
Type 2
FLIGHT
TIME
FLIGHT
TIME
FLIGHT
: TIME
OZ348
20:30
OZ348
20:30
OZ348
: 20:30
UA102
21:10
UA102
21:10
•• Avoid combinations of a text colour and background colour of contrasting brightness.
(Brightness: refers to the lightness or darkness of a colour which varies depending on the amount of
light emitted.)
――Avoid using grey as it may contribute to afterimage burn-in.
――Avoid using colours of contrasting brightness (black and white; grey).
FLIGHT : TIME
FLIGHT : TIME
OZ348 : 20:30
OZ348 : 20:30
[ Step 1 ]
[ Step 2 ]
FLIGHT
: TIME
OZ348
: 20:30
[ Step 3 ]
-- Regularly display a moving image along with a logo.
Interval: Display a moving image along with a logo for 60 seconds after using for 4 hours.
150
Licence
Manufactured under licence from Dolby Laboratories.
Dolby and the double-D symbol are trademarks of Dolby Laboratories.
DivX Certified Ⓡ to play DivX Ⓡ video up to HD 1080p, including premium
content.
DivXⓇ, DivX CertifiedⓇ and associated logos are trademarks of Rovi
Corporation or its subsidiaries and are used under licence.
Ⓡ
2.0 Channel
Manufactured under licence under U.S. Patent Nos: 5,956,674; 5,974,380;
6,487,535 & other U.S. and worldwide patents issued & pending. DTS, the
Symbol, & DTS and the Symbol together are registered trademarks & DTS 2.0
Channel is a trademark of DTS, Inc. ⓒ DTS, Inc. All Rights Reserved.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the
HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in
the United States and other countries.
ABOUT DIVX VIDEO: DivXⓇ is a digital video format created by DivX, LLC, a subsidiary of Rovi
Corporation. This is an official DivX CertifiedⓇ device that has passed rigorous testing to verify that
it plays DivX video. Visit divx.com for more information and software tools to convert your files into
DivX videos.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX CertifiedⓇ device must be registered in order to play
purchased DivX Video-on-Demand (VOD) movies. To obtain your registration code, locate the
DivX VOD section in your device setup menu. Go to vod.divx.com for more information on how to
complete your registration.
Covered by one or more of the following U.S. patents: 7,295,673; 7,460,668; 7,515,710; 7,519,274
Open Source Licence Notice
In the case of using open source software, Open Source Licences are available on the product menu.
Open Source Licence Notice is written only English.
For information on the Open Source Licence Notice, contact the Samsung Customer Centre or send
email to oss.request@samsung.com.
151
Terminology
480i / 480p / 720p / 1080i /
1080p____ Each of the scanning
rates above refers to the number of
effective scanning lines that decides
the screen resolution. The scanning
rate may be indicated in i (interlaced)
or p (progressive), depending on the
scanning method.
- Scanning
Scanning refers to a process of sending
pixels that form an image progressively.
A larger number of pixels will deliver a
clearer and more vivid picture.
- Progressive
In progressive scan mode, all lines
of pixels are scanned one by one
(progressively) on the screen.
- Interlaced
In interlaced scan mode, every other
line of pixels is scanned from top to
bottom first and then the remaining
lines of pixels (that were not scanned)
are scanned.
Non-interlace Mode and Interlace
Mode____ Non-interlace mode
(progressive scan) displays a horizontal
line from the top to the bottom of a
screen progressively. Interlace mode
displays the odd number lines first
and the even number lines next. Noninterlace mode is mainly used in
monitors as it produces screen clarity
and interlace mode is mainly used in
TVs.
Dot Pitch____ The screen consist of
red, green and blue dots. A shorter
distance between the dots produces a
higher resolution. Dot pitch refers to the
distance between the shortest distance
between dots of the same colour. Dot
pitch is measured in millimeters.
Vertical Frequency____ The product
displays a single image many times
per second (like a fluorescent light that
flickers) to display an image for a viewer
to see. The rate of a single image being
displayed repeatedly per second is
called vertical frequency or refresh rate.
Vertical frequency is measured in Hz.
E.g. 60Hz refers to a single image being
displayed 60 times in one second.
Horizontal Frequency____ The time
required to scan a single line from the
left to the right side of the screen is
called a horizontal cycle. The reciprocal
number of a horizontal cycle is called
horizontal frequency. Horizontal
frequency is measured in kHz.
Source____ Input source refers to a
video source device connected to the
product such as a camcorder or video
or DVD player.
Plug & Play____ Plug & Play is a
function that allows the automatic
exchange of information between a
SMART Signage TV and PC to produce
an optimum display environment. The
product uses VESA DDC (international
standard) to execute Plug & Play.
Resolution____ Resolution is the
number of horizontal dots (pixels) and
vertical dots (pixels) that form a screen.
It represents the level of display detail.
A higher resolution enables more
data to be displayed on the screen
and is useful to perform multiple tasks
simultaneously.
E.g. A resolution of 1920 X 1080 consists
of 1,920 horizontal pixels (horizontal
resolution) and 1,080 vertical pixels
(vertical resolution).
DVD (Digital Versatile Disc)____ DVD
refers to a CD-sized mass storage disk
where you can save multimedia (audio,
video or game) applications using
MPEG-2 video compression technology.
HDMI (High Definition Multimedia
Interface)____ It is an interface that
can be connected to a digital audio
source as well as a high-definition video
source by using a single cable without
compression.
Multiple Display Control (MDC)____
MDC (Multiple Display Control) is an
application that allows multiple display
devices to be controlled simultaneously
using a PC. Communication between
a PC and monitor takes place using
RS232C (serial data transmission) and
RJ45 (LAN) cables.
152
Download PDF

advertising