Samsung | OH46F | Samsung OH55F Benutzerhandbuch

USER MANUAL
OH46F I OH55F
The colour and the appearance may differ depending on the product, and the specifications are subject to change without prior
notice to improve the performance.
The contents of this manual are subject to change without notice to improve quality.
© Samsung Electronics
Samsung Electronics owns the copyright for this manual.
Use or reproduction of this manual in parts or entirety without the authorization of Samsung Electronics is prohibited.
Trademarks other than that of Samsung Electronics are owned by their respective owners.
••
An administration fee may be charged if either
‒‒ (a) an engineer is called out at your request and there is no defect in the product
(i.e. where you have failed to read this user manual).
‒‒ (b) you bring the unit to a repair centre and there is no defect in the product
(i.e. where you have failed to read this user manual).
••
The amount of such administration charge will be advised to you before any work or home visit is carried out.
Table of contents
Before Using the Product
Safety Precautions
6
Cleaning6
Storage6
Electricity and Safety
7
Installation8
Operation9
Connecting and Using
a Source Device
Using MDC
MDC Programme Installation/Uninstallation42
Installation42
Uninstallation42
Before Connecting
Pre-connection Checkpoints
Before connecting cables
32
32
33
Connecting to a PC
Connection Using an HDMI-DVI Cable
Connection Using an HDMI Cable
34
34
34
Connecting to MDC
Using MDC via RS-232C (serial data
communications standards)
Using MDC via Ethernet
Connecting to a Video Device
Connection Using an HDMI-DVI Cable
Connection Using an HDMI Cable
35
35
35
Player feature
Connecting the HDBase-T
36
Parts12
Parts12
Reverse Side
13
Anti-theft Lock
14
Remote Control
15
Connecting to an Audio System
37
Connecting the LAN Cable
37
Before Installing the Product (Installation
Guide)17
Tilting Angle and Rotation
17
Ventilation17
Web Browser39
Settings39
Refresh Options41
Preparations
Checking the Components
11
Components11
Installing the Wall Mount
Installing the Wall Mount Kit
Wall Mount Kit Specifications
19
19
19
Remote Control (RS232C)
20
Cable Connection
20
Connection23
Control Codes
24
Changing the Input source
38
Source38
43
43
43
Player45
Viewing content
45
When content is running
46
Available menu
46
File Formats Compatible with Player47
Schedule52
Clone Product53
ID Settings54
Device ID54
Device ID Auto Set54
PC Connection Cable54
Video Wall55
Video Wall55
Horizontal x Vertical55
Screen Position55
Format56
2
Table of contents
Network Status57
Picture Mode58
On/Off Timer59
On Timer59
Off Timer60
Holiday Management60
Ticker61
URL Launcher62
URL Launcher Settings63
Approving a connected device from the server64
Setting the current time
65
Screen Adjustment
Picture Mode66
Black Tone70
Flesh Tone70
RGB Only Mode70
Colour Space70
HDMI UHD Color71
Motion Lighting71
Picture Options72
Colour Tone72
Digital Clean View72
HDMI Black Level73
Film Mode73
Dynamic Backlight73
Picture Size74
Picture Size74
Fit to Screen74
Zoom/Position74
Picture Off75
Reset Picture75
Backlight / Contrast / Brightness / Sharpness /
Colour / Tint (G/R)67
Colour Temperature68
OnScreen Display
White Balance68
2 Point68
10 Point68
Display Orientation76
Onscreen Menu Orientation76
Source Content Orientation76
Aspect Ratio76
Gamma69
Calibrated value69
Advanced Settings70
Dynamic Contrast70
Screen Protection77
Auto Protection Time77
Screen Burn Protection77
Message Display80
Source Info80
No Signal Message80
MDC Message80
Download Status Message80
Language81
Reset OnScreen Display81
Network
Network Status82
Open Network Settings82
Network type82
Network Settings (Wired)
83
Network Setting (Wireless)
85
WPS(PBC)87
Server Network Settings88
Connect to server88
MagicInfo Mode88
Server Access88
FTP Mode88
Proxy server88
Wi-Fi Direct89
Mobile Device Manager90
Access Notification90
Mobile Device List90
Device Name90
3
Table of contents
System
Auto Power Off98
Accessibility91
Menu Transparency91
High Contrast91
Enlarge91
Fan and Temperature99
Fan Control99
Fan Speed Setting99
Outdoor Mode99
Temperature Control99
Start Setup92
Time93
Clock Set93
NTP Settings93
DST93
Sleep Timer93
Power On Delay93
Input Device Manager100
Keyboard Language100
Keyboard type100
Input Language Shortcut100
Play via100
Change PIN101
Auto Source Switching94
Auto Source Switching94
Primary Source Recovery94
Primary Source94
Secondary Source94
Security102
Safety Lock On102
USB Auto Play Lock102
Mobile Connection Lock102
Remote Management102
Power Control95
Auto Power On95
Max. Power Saving95
Standby Control95
Network Standby96
Power Button96
General103
Smart Security103
Anynet+ (HDMI-CEC)104
HDMI Hot Plug106
Custom Logo106
Game Mode107
Empty Storage107
Eco Solution97
Brightness Limit97
Energy Saving Mode97
Eco Sensor97
Screen Lamp Schedule98
No Signal Power Off98
Support
Software Update108
Update now108
Auto update108
Contact Samsung108
Reset All108
Troubleshooting Guide
Requirements Before Contacting Samsung
Customer Service Centre
Testing the Product
Checking the Resolution and Frequency
Check the followings.
109
109
109
110
Q & A
114
Specifications
General116
Preset Timing Modes
117
Reset System107
4
Table of contents
Appendix
Responsibility for the Pay Service (Cost to
Customers)119
Not a product defect
119
A Product damage caused by customer's
fault119
Others119
Optimum Picture Quality and Afterimage Burnin Prevention
120
Optimum Picture Quality
120
Prevention of Afterimage Burn-in
120
Licence122
Terminology123
5
Chapter 01
Before Using the Product
Safety Precautions
Cleaning
――Exercise care when cleaning as the panel and exterior of advanced LCDs are easily scratched.
Warning
A serious or fatal injury may result if instructions are not followed.
Caution
Personal injury or damage to properties may result if instructions are
not followed.
Activities marked by this symbol are prohibited.
――Take the following steps when cleaning.
1
2
Power off the product and computer.
Disconnect the power cord from the product.
――Hold the power cable by the plug and do not touch the cable with wet hands. Otherwise, an electric shock
may result.
3
Wipe the product with a clean, soft and dry cloth.
‒‒ Do not use detergents that contain alcohol, solvent or surface-active agents.
‒‒ Do not spray water or detergent directly on the product.
Instructions marked by this symbol must be followed.
4
Wet a soft and dry cloth in water and wring thoroughly to clean the exterior of the product.
5
Connect the power cord to the product when cleaning is finished.
6
Power on the product and computer.
Storage
Due to the characteristics of high-glossy products, using a UV humidifier nearby may create whitecoloured stains on the product.
――Contact Customer Service Centre if the inside of the product needs cleaning (service fee will be charged).
6
Electricity and Safety
Caution
Warning
Do not disconnect the power cord while the product is being used.
Do not use a damaged power cord or plug, or a loose power socket.
Only use the power cord provided with your product by Samsung. Do not use the power cord with other
products.
•• An electric shock or fire may result.
Do not use multiple products with a single power socket.
•• Overheated power sockets may cause a fire.
Do not touch the power plug with wet hands. Otherwise, an electric shock may result.
Insert the power plug all the way in so it is not loose.
•• An unsecure connection may cause a fire.
Connect the power plug to a grounded power socket (type 1 insulated devices only).
•• The product may become damaged by an electric shock.
•• A fire or electric shock may result.
Keep the power socket where the power cord is connected unobstructed.
•• The power cord must be disconnected to cut off power to the product when an issue occurs.
•• Note that the product is not completely powered down by using only the power button on the
remote.
Hold the plug when disconnecting the power cord from the power socket.
•• An electric shock or fire may result.
•• An electric shock or injury may result.
Do not bend or pull the power cord with force. Be careful not to leave the power cord under a heavy
object.
•• Damage to the cord may result in a fire or electric shock.
Do not place the power cord or product near heat sources.
•• A fire or electric shock may result.
Clean any dust around the pins of the power plug or the power socket with a dry cloth.
•• A fire may result.
7
Installation
Caution
Warning
Do not drop the product while moving.
DO NOT PLACE CANDLES, INSECT REPELLANTS OR CIGARETTES ON TOP OF THE PRODUCT. DO NOT
INSTALL THE PRODUCT NEAR HEAT SOURCES.
Do not set down the product on its front.
•• A fire may result.
•• Product failure or personal injury may result.
•• The screen may become damaged.
Have a technician install the wall-mount hanger.
When installing the product on a cabinet or shelf, make sure that the bottom edge of the front of the
product is not protruding.
•• Installation by an unqualified person can result in an injury.
•• The product may fall and become damaged and/or cause an injury.
•• Only use approved cabinets.
•• Install the product only on cabinets or shelves of the right size.
Do not install the product in poorly ventilated spaces such as a bookcase or closet.
•• An increased internal temperature may cause a fire.
Install the product at least 10 cm away from the wall to allow ventilation.
•• An increased internal temperature may cause a fire.
Keep the plastic packaging out of the reach of children.
•• Children may suffocate.
Do not install the product on an unstable or vibrating surface (insecure shelf, sloped surface, etc.)
Set down the product gently.
•• Product failure or personal injury may result.
Installing the product in an unusual place (a place exposed to a lot of fine dust, chemical substances,
extreme temperatures or a significant presence of moisture, or a place where the product will operate
continuously for an extended period of time) may seriously affect its performance.
•• Be sure to consult Samsung Customer Service Centre if you want to install the product at such a
place.
•• The product may fall and become damaged and/or cause an injury.
•• Using the product in an area with excess vibration may damage the product or cause a fire.
Do not install the product within the reach of young children.
•• The product may fall and injure children.
•• As the front is heavy, install the product on a flat and stable surface.
Edible oil, such as soybean oil, can damage or deform the product. Do not install the product in a kitchen
or near a kitchen counter.
Precautions during installation and storage
•• After opening the cover, install the product within 1 hour under humidity of 60% or below. (P. 33)
•• Keep the predefined humidity while opening the cover or assembling the housing (e.g. connection of
external device, F/W update).
•• During operation and storage of the product, be sure to attach the cover.
8
Operation
Do not lift or move the product by pulling the power cord or any cable.
•• Product failure, an electric shock or fire may result from a damaged cable.
Warning
There is a high voltage inside the product. Never disassemble, repair or modify the product yourself.
•• A fire or electric shock may result.
•• Contact Samsung Customer Service Centre for repairs.
Before moving the product, turn off the power switch and disconnect the power cable and all other
connected cables.
•• Otherwise, the power cord may be damaged and a fire or electric shock may result.
If the product generates abnormal sounds, a burning smell or smoke, disconnect the power cord
immediately and contact Samsung Customer Service Centre.
•• An electric shock or fire may result.
Do not use or keep combustible spray or an inflammable substance near the product.
•• An explosion or fire may result.
Ensure the vents are not blocked by tablecloths or curtains.
•• An increased internal temperature may cause a fire.
Do not insert metallic objects (chopsticks, coins, hairpins, etc) or objects that burn easily (paper, matches,
etc) into the product (via the vent or input/output ports, etc).
•• Be sure to power off the product and disconnect the power cord when water or other foreign
substances have entered the product. Then contact Samsung Customer Service Centre.
•• Product failure, an electric shock or fire may result.
Do not place objects containing liquid (vases, pots, bottles, etc) or metallic objects on top of the product.
Do not let children hang from the product or climb on top of it.
•• Be sure to power off the product and disconnect the power cord when water or other foreign
substances have entered the product. Then contact Samsung Customer Service Centre.
•• Children may become injured or seriously harmed.
•• Product failure, an electric shock or fire may result.
If the product is dropped or the outer case is damaged, turn off the power switch and disconnect the
power cord. Then contact Samsung Customer Service Centre.
Do not block the vent on the product. The product may not function properly due to potential
overheating.
•• Continued use can result in a fire or electric shock.
Do not leave heavy objects or items that children like (toys, sweets, etc.) on top of the product.
Do not attempt to insert your fingers or objects into the vents.
•• Product failure or personal injury may result.
•• The product or heavy objects may fall as children try to reach for the toys or sweets resulting in a
serious injury.
During a lightning or thunderstorm, power off the product and remove the power cable.
•• A fire or electric shock may result.
Do not drop objects on the product or apply impact.
•• A fire or electric shock may result.
Do not move the product by pulling the power cord or any cable.
•• Product failure, an electric shock or fire may result from a damaged cable.
If a gas leakage is found, do not touch the product or power plug. Also, ventilate the area immediately.
•• Sparks can cause an explosion or fire.
9
Caution
Leaving the screen fixed on a stationary image for an extended period of time may cause afterimage
burn-in or defective pixels.
•• Activate power-saving mode or a moving-picture screen saver if you will not be using the product for
an extended period of time.
Disconnect the power cord from the power socket if you do not plan on using the product for an extended
period of time (vacation, etc).
•• Dust accumulation combined with heat can cause a fire, electric shock or electric leakage.
Use the product at the recommended resolution and frequency.
•• Your eyesight may deteriorate.
When replacing the battery, insert it with the right polarity (+, -).
•• Otherwise, the battery may become damaged or it may cause fire, personal injury or damage due to
leakage of the internal liquid.
Use only the specified standardised batteries, and do not use a new battery and a used battery at the
same time.
•• Otherwise, the batteries may be damaged or cause fire, personal injury or damage due to a leakage
of the internal liquid.
The batteries (and rechargeable batteries) are not ordinary refuse and must be returned for recycling
purposes. The customer is responsible for returning the used or rechargeable batteries for recycling.
•• The customer can return used or rechargeable batteries to a nearby public recycling centre or to a
store selling the same type of the battery or rechargeable battery.
Do not hold the product upside-down or move it by holding the stand.
•• The product may fall and become damaged or cause an injury.
Looking at the screen too close for an extended period of time can deteriorate your eyesight.
Rest your eyes for more than 5 minutes for every 1 hour of product use.
•• Eye fatigue will be relieved.
Do not touch the screen when the product has been turned on for an extended period of time as it will
become hot.
Store small accessories out of the reach of children.
Exercise caution when adjusting the product angle or stand height.
•• Your hand or finger may get stuck and injured.
•• Tilting the product at an excessive angle may cause the product to fall and an injury may result.
Do not place heavy objects on the product.
•• Product failure or personal injury may result.
When using headphones or earphones, do not turn the volume too high.
•• Having the sound too loud may damage your hearing.
Be careful that children do not place the battery in their mouths when removed from the remote control.
Place the battery in a location that children or infants cannot reach.
•• If children have had the battery in their mouths, consult your doctor immediately.
10
Chapter 02
Preparations
Checking the Components
Components
–– Contact the vendor where you
purchased the product if any
components are missing.
–– The pictures may look different from
Warranty card
QUICK SETUP GUIDE
(Not available in some locations)
the actual components.
–– A stand is not provided with the
Regulatory guide
Power cord
-
product. To install a stand, you can
-
+
purchase one separately.
+
Batteries
(Not available in some locations)
Remote Control
11
Parts
Parts
――The colour and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality.
Remote sensor
POWER
Parts
Remote sensor
Description
Press a button on the remote control pointing at the sensor on the front of the product to perform the corresponding function.
――Using other display devices in the same space as the remote control of this product can cause the other display devices to be inadvertently controlled.
Use the remote control within 7 m to 10 m from the sensor on the product at an angle of 30° from the left and right.
――Store used batteries out of reach of children and recycle.
――Do not use a new and used battery together. Replace both batteries at the same time.
――Remove batteries when the remote control is not to be used for an extended period of time.
12
Reverse Side
――The colour and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality.
RS232C AUDIO
IN
OUT
OUT
Port
RS232C IN
USB
RJ45
(LAN OUT)
HDBT
(LAN IN)
HDMI IN 1
HDMI IN 2
Description
Connects to MDC using an RS232C adapter.
RS232C OUT
AUDIO OUT
Outputs sound to an audio device via an audio cable.
USB
Connect to a USB memory device.
RJ45 (LAN OUT)
- Wired LAN connection port used to connect an external device such as a laptop to connect to the Internet.
-C
onnects to MDC using a LAN cable.
HDBT (LAN IN)
-S
ends the HDMI signal to a connected LAN cable using an HDBaseT transmitter.
- Connects to MDC using a LAN cable.
HDMI IN 1, HDMI IN 2
Connects to a source device using a HDMI cable or HDMI-DVI cable.
13
Anti-theft Lock
――An anti-theft lock allows you to use the product securely even in public places.
――The locking device shape and locking method depend on the manufacturer. Refer to the user guide provided with your anti-theft locking device for details.
――The following images are for reference only. Real-life situations may differ from what is shown in the images.
To lock an anti-theft locking device:
1
Fix the cable of your anti-theft locking device to a heavy object such as a desk.
2
Put one end of the cable through the loop on the other end.
3
Insert the locking device into the anti-theft lock slot at the back of the product.
4
Lock the locking device.
‒‒ An anti-theft locking device can be purchased separately.
‒‒ Refer to the user guide provided with your anti-theft locking device for details.
‒‒ Anti-theft locking devices can be purchased at electronics retailers or online.
14
Remote Control
――Using other display devices in the same space as the remote control of this product can cause the other display devices to be inadvertently controlled.
――A button without a description in the image below is not supported on the product.
POWER
OFF
Power on the product.
.QZ
ABC
DEF
GHI
JKL
MNO
PRS
TUV
WXY
1
4
7
DEL-/--
Adjust the volume.
Change the input source.
Display or hide the onscreen display menu, or
return to the previous menu.
2
5
8
SYMBOL
0
3
6
MENU
SOURCE
HOME
Number buttons
Enter the password in the OSD menu.
9
–– Remote control button functions may
differ for different products.
–– Remove batteries when the remote
control is not to be used for an
CH LIST
extended period of time.
Mute the sound.
MUTE
VOL
Power off the product.
CH
MagicInfo
Player I
Unmuting the sound: Press MUTE again or press
the volume control (+ VOL -) button.
Player Launch Button.
15
Quickly select frequently used functions by
pressing it while a USB content is playing.
TOOLS
INFO
Display information about the current input
source.
Move to the upper, lower, left or right menu, or
adjust an option's setting.
Confirm a menu selection.
Return to the previous menu.
RETURN
EXIT
PC
If multiple products are connected through the
Video Wall feature, press the SET button and
enter a Device ID using the numeric buttons.
Control the product using the remote control.
Cancel a value that has been set using the SET
button and control all connected products using
the remote control.
DVI
HDMI
DP
B
C
D
UNSET
LOCK
A
Exit the current menu.
Manually select a connected input source from
HDMI 1 and HDMI 2.
IR control
SET
It sets safe lock function.
–– Remote control button functions may
differ for different products.
To place batteries in the remote control
16
Before Installing the Product
(Installation Guide)
To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation instructions.
•• Ensure that an authorised installation company installs the wall mount.
•• Otherwise, it may fall and cause personal injury.
•• Make sure to install the specified wall mount.
15 ˚
Tilting Angle and Rotation
――Contact Samsung Customer Service Centre for further details.
•• The product can be tilted at a maximum angle of 15° from a perpendicular wall surface.
•• To use the product vertically (portrait), turn it clockwise so that the LED is pointing down.
Air intake
Ventilation
Installation on a Perpendicular Wall
A Minimum 40 mm
B Ambient temperature: Under 50°C
A
•• When installing the product on a perpendicular wall, allow at least 40 mm of space between the product and wall surface
for ventilation and ensure that the ambient A temperature is kept below 50°C.
――Do not block the vent on the product.
Air vent
B
Figure 1.1 Side view
17
Installation on an Indented Wall
Figure 1.3 Side view
――Contact Samsung Customer Service Centre for further details.
B
B
B
Plane view
A Minimum 40 mm
B Minimum 40 mm
A
C Ambient temperature: Under 50°C
――When installing the product on an indented wall, allow at least the space specified above between the product and wall for
ventilation and ensure that the ambient temperature is kept below 50°C.
B
C
Figure 1.2 Side view
18
Installing the Wall Mount
――The colour and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality.
Installing the Wall Mount Kit
The wall mount kit (sold separately) allows you to mount the product on the wall.
For detailed information on installing the wall mount, see the instructions provided with the wall mount.
We recommend you contact a technician for assistance when installing the wall mount bracket.
Samsung Electronics is not responsible for any damage to the product or injury to yourself or others if you select to install the wall mount on your own.
Wall Mount Kit Specifications
――Install your wall mount on a solid wall perpendicular to the floor. If you install the
product on a slanted wall, it may fall and result in severe personal injury. Before
attaching the wall mount to surfaces other than plaster board, please contact your
nearest dealer for additional information.
•• Samsung wall mount kits contain a detailed installation manual and all parts necessary for assembly are provided.
•• Do not use screws that are longer than the standard length or do not comply with the VESA standard screw specifications.
Screws that are too long may cause damage to the inside of the product.
•• For wall mounts that do not comply with the VESA standard screw specifications, the length of the screws may differ
depending on the wall mount specifications.
•• Do not fasten the screws too firmly. This may damage the product or cause the product to fall, leading to personal injury.
Samsung is not liable for these kinds of accidents.
•• Samsung is not liable for product damage or personal injury when wall mount is used or the consumer fails to follow the
product installation instructions.
•• Do not mount the product at more than a 15 degree tilt.
•• Always have two people mount the product on a wall.
•• Standard dimensions for wall mount kits are shown in the table below.
Unit: mm (inches)
Model name
Screw hole specs (A * B) in
millimetres
OH46F
995 x 500 (39.2 x 19.7)
OH55F
1186 x 560 (46.7 x 22.0)
Standard Screw
M8
Quantity
4
――Do not install your Wall Mount Kit while your product is turned on. It may result in personal injury due to electric shock.
19
Remote Control (RS232C)
•• Pin assignment
1 2 3 4 5
5 4 3 2 1
6 7 8 9
9 8 7 6
Cable Connection
RS232C Cable
Interface
RS232C (9 pins)
Pin
TxD (No.2), RxD (No.3), GND (No.5)
Bit rate
9600 bps
Data bits
8 bit
Parity
None
Stop bit
1 bit
Flow control
None
Maximum length
15 m (only shielded type)
<Male type>
Pin
<Female type>
Signal
1
Detect data carrier
2
Received data
3
Transmitted data
4
Prepare data terminal
5
Signal ground
6
Prepare data set
7
Send request
8
Clear to send
9
Ring indicator
20
LAN Cable
•• RS232C cable
Connector: 9-Pin D-Sub to Stereo Cable
6
•• Pin assignment
3
2
1
1
1 2 3 4 5 6 7 8
-P2-
5
9
-P1-
-P1Male type
-P1-
-P2-
-P2-
Rx
3
----------
2
Tx
STEREO
Tx
2
----------
1
Rx
PLUG
Gnd
5
----------
3
Gnd
(3.5ø)
Pin No
Standard Colour
Signal
1
White and orange
TX+
2
Orange
TX-
3
White and green
RX+
4
Blue
NC
5
White and blue
NC
6
Green
RX-
7
White and brown
NC
8
Brown
NC
21
Cross LAN cable (PC to PC)
•• Connector : RJ45
Direct LAN cable (PC to HUB)
HUB
RJ45
RJ45
P2
RJ45
P2
P1
TX+
1
TX-
P2
P1
P1
Signal
P1
P2
Signal
<-------->
1
TX+
2
<-------->
2
TX-
RX+
3
<-------->
3
RX+
RX-
6
<-------->
6
RX-
Signal
P1
P2
Signal
TX+
1
<-------->
3
RX+
TX-
2
<-------->
6
RX-
RX+
3
<-------->
1
TX+
RX-
6
<-------->
2
TX-
22
Connection
•• Connection 2
――Ensure you connect each of the adapters to the correct RS232C IN or OUT port on the product.
•• Connection 1
RJ45
RS232C
IN
RS232C
OUT
IN
RS232C
OUT
IN
RJ45
RS232C
OUT
IN
OUT
•• Connection 3
RJ45
RS232C
OUT
RS232C
IN
RS232C
OUT
IN
RS232C
OUT
IN
OUT
23
Control Codes
E.g. Power On & ID=0
Viewing control state (Get control command)
Header
Command
0xAA
Command type
ID
Data length
Checksum
0
Command
0xAA
Command type
ID
Command
0xAA
0x11
Header
Command
0xAA
0x11
ID
ID
Data length
Data 1
1
"Power"
Data length
Data 1
1
1
Checksum
12
•• To control all devices connected by a serial cable simultaneously irrespective of IDs, set the ID
as "0xFE" and transmit commands. Commands will be executed by each device but ACK will not
respond.
Controlling (Set control command)
Header
Header
Data length
Data
1
Value
Checksum
Command
No.
Command type
Command
Value range
1
Power control
0x11
0~1
2
Volume control
0x12
0~100
3
Input source control
0x14
-
4
Screen mode control
0x18
-
5
Screen size control
0x19
0~255
6
Video wall mode control
0x5C
0~1
7
Safety Lock
0x5D
0~1
8
Video Wall On
0x84
0~1
9
Video Wall User Control
0x89
-
•• All communications take place in hexadecimals. The checksum is calculated by adding up all values
except the header. If a checksum adds up to be more than 2 digits as shown below (11+FF+01+01=112),
the first digit is removed.
24
Power control
Volume control
•• Function
•• Function
A product can be powered on and off using a PC.
The volume of a product can be adjusted using a PC.
•• Viewing power state (Get Power ON / OFF Status)
Header
Command
0xAA
0x11
ID
•• Viewing volume state (Get Volume Status)
Data length
Checksum
0
•• Setting power ON/Off (Set Power ON / OFF)
Header
Command
0xAA
0x11
ID
Header
Command
0xAA
0x12
ID
Data length
0
•• Setting the volume (Set Volume)
Data length
Data
1
"Power"
Checksum
Header
Command
0xAA
0x12
ID
Data length
Data
1
"Volume"
"Power": Power code to be set on a product.
"Volume": Volume value code to be set on a product. (0-100)
1: Power ON
•• Ack
0: Power OFF
Header
Command
0xAA
0xFF
•• Ack
Header
Command
0xAA
0xFF
ID
Data length
Ack/Nak
r-CMD
Val1
3
'A'
0x11
"Power"
Checksum
Header
Command
0xAA
0xFF
0xAA
0xFF
ID
Data length
Ack/Nak
r-CMD
Val1
3
'N'
0x11
"ERR"
Data length
Ack/Nak
r-CMD
Val1
3
'A'
0x12
"Volume"
Checksum
•• Nak
•• Nak
Command
ID
Checksum
"Volume": Volume value code to be set on a product. (0-100)
"Power": Power code to be set on a product.
Header
Checksum
Checksum
ID
Data length
Ack/Nak
r-CMD
Val1
3
'N'
0x12
"ERR"
Checksum
"ERR" : A code showing what error has occurred.
"ERR" : A code showing what error has occurred.
25
Input source control
•• Ack
•• Function
The input source of a product can be changed using a PC.
Header
Command
0xAA
0xFF
ID
Data length
Ack/Nak
r-CMD
Val1
3
'A'
0x14
"Input
Source"
•• Viewing input source state (Get Input Source Status)
Header
Command
0xAA
0x14
ID
Data length
"Input Source": An input source code to be set on a product.
Checksum
•• Nak
0
•• Setting the input source (Set Input Source)
Header
Command
0xAA
0x14
ID
Checksum
Data length
Data
1
"Input Source"
Checksum
Header
Command
0xAA
0xFF
ID
Data length
Ack/Nak
r-CMD
Val1
3
'N'
0x14
"ERR"
Checksum
"ERR" : A code showing what error has occurred.
"Input Source": An input source code to be set on a product.
0x0C
Input source
0x20
MagicInfo
0x21
HDMI1
0x22
HDMI1_PC
0x23
HDMI2
0x24
HDMI2_PC
0x55
HDBT
――HDMI1_PC and HDMI2_PC cannot be used with the Set command. They only respond to "Get" commands.
――Available input sources may vary depending on the model.
――MagicInfo is only available with models that contain the MagicInfo function.
26
Screen mode control
•• Nak
•• Function
The screen mode of a product can be changed using a PC.
Header
Command
0xAA
0xFF
ID
Data length
Ack/Nak
r-CMD
Val1
3
'N'
0x18
"ERR"
Checksum
"ERR": A code showing what error has occurred
Screen mode cannot be controlled when the Video Wall function is enabled.
•• Viewing screen status (Get Screen Mode Status)
Header
Command
0xAA
0x18
ID
Data length
Screen size control
Checksum
0
•• Function
The screen size of a product can be changed using a PC.
•• Setting the picture size (Set Picture Size)
Header
Command
0xAA
0x18
ID
Data length
Data
Checksum
1
"Screen Mode"
"Screen Mode": A code that sets the product status
•• Viewing the screen size (Get Screen Size Status)
Header
Command
0xAA
0x19
0x01
16 : 9
•• Ack
0x04
Zoom
Header
Command
0x31
Wide Zoom
0x0B
4:3
0xAA
0xFF
•• Ack
Header
Command
0xAA
0xFF
ID
Data length
Ack/Nak
r-CMD
Val1
3
'A'
0x18
"Screen
Mode"
"Screen Mode": A code that sets the product status
Checksum
ID
Data length
Checksum
0
ID
Data
length
Ack/Nak
r-CMD
Val1
3
'A'
0x19
"Screen Size"
Checksum
"Screen Size": product screen size (range: 0 – 255, unit: inch)
•• Nak
Header
Command
0xAA
0xFF
ID
Data
length
Ack/Nak
r-CMD
Val1
3
'N'
0x19
"ERR"
Checksum
"ERR": A code showing what error has occurred
27
Video Wall Mode Control
Safety Lock On
•• Function
•• Function
Video Wall mode can be activated on a product using a PC.
PC can be used to turn the Safety Lock On function on or off on a product.
This control is only available on a product whose Video Wall is enabled.
This control is available regardless of whether or not the power is turned on.
•• Viewing video wall mode (Get Video Wall Mode)
Header
Command
0xAA
0x5C
ID
•• Viewing the safety lock state (Get Safety Lock Status)
Data length
Checksum
0
•• Setting the video wall (Set Video Wall Mode)
Header
Command
0xAA
0x5C
ID
Header
Command
0xAA
0x5D
ID
Data length
0
•• Enabling or disabling safety lock (Set Safety Lock Enable / Disable)
Data length
Data
Checksum
1
"Video Wall Mode"
Header
Command
0xAA
0x5D
ID
Data length
Data
1
"Safety Lock"
"Video Wall Mode": A code used to activate Video Wall mode on a product
"Safety Lock": Safety lock code to be set on a product
1: Full
1: ON
0: Natural
0: OFF
•• Ack
•• Ack
Header
Command
0xAA
0xFF
ID
Data
length
Ack/Nak
r-CMD
Val1
3
'A'
0x5C
"Video Wall
Mode"
Checksum
0xAA
0xFF
ID
Data
length
Ack/Nak
r-CMD
Val1
3
'A'
0x5C
"ERR"
Command
0xAA
0xFF
ID
Data
length
Ack/Nak
r-CMD
Val1
3
'A'
0x5D
"Safety Lock"
Checksum
•• Nak
•• Nak
Command
Header
Checksum
"Safety Lock": Safety lock code to be set on a product
"Video Wall Mode": A code used to activate Video Wall mode on a product
Header
Checksum
Header
Command
0xAA
0xFF
Checksum
ID
Data
length
Ack/Nak
r-CMD
Val1
3
'N'
0x5D
"ERR"
Checksum
"ERR": A code showing what error has occurred
"ERR": A code showing what error has occurred
28
Video Wall On
Video Wall User Control
•• Function
•• Function
Turn Video Wall on or off on the product from your computer.
Turn the Video Wall function on or off on the product from your computer.
•• Get Video Wall On/Off Status
Header
Command
0xAA
0x84
•• Get Video Wall Status
ID
Data length
Checksum
0
•• Set Video Wall On/Off
Header
Command
0xAA
0x89
ID
Data length
Checksum
0
•• Set Video Wall
Header
Command
0xAA
0x84
ID
Data length
Data
Checksum
1
V.Wall_On
Header
Command
0xAA
0x89
ID
Data length
Val1
Val2
2
Wall_Div
Wall_SNo
Checksum
Wall_Div: Video Wall Divider code assigned to the product
•• V.Wall_On: Video Wall code to be assigned to the product
1: Video Wall ON
0: Video Wall OFF
•• Ack
Header
Command
0xAA
0xFF
ID
Data length
Ack/Nak
r-CMD
Val1
3
'A'
0x84
V.Wall_On
Data length
Ack/Nak
r-CMD
Val1
3
'N'
0x84
ERR
Checksum
V.Wall_On : Same as above
•• Nak
Header
Command
0xAA
0xFF
ID
Checksum
"ERR": A code showing what error has occurred
29
10x10 Video Wall Model
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Off
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
1
0x11
0x12
0x13
0x14
0x15
0x16
0x17
0x18
0x19
0x1A
0x1B
0x1C
0x1D
0x1E
0x1F
2
0x21
0x22
0x23
0x24
0x25
0x26
0x27
0x28
0x29
0x2A
0x2B
0x2C
0x2D
0x2E
0x2F
3
0x31
0x32
0x33
0x34
0x35
0x36
0x37
0x38
0x39
0x3A
0x3B
0x3C
0x3D
0x3E
0x3F
4
0x41
0x42
0x43
0x44
0x45
0x46
0x47
0x48
0x49
0x4A
0x4B
0x4C
0x4D
0x4E
0x4F
5
0x51
0x52
0x53
0x54
0x55
0x56
0x57
0x58
0x59
0x5A
0x5B
0x5C
0x5D
0x5E
0x5F
6
0x61
0x62
0x63
0x64
0x65
0x66
0x67
0x68
0x69
0x6A
0x6B
0x6C
0x6D
0x6E
0x6F
7
0x71
0x72
0x73
0x74
0x75
0x76
0x77
0x78
0x79
0x7A
0x7B
0x7C
0x7D
0x7E
N/A
8
0x81
0x82
0x83
0x84
0x85
0x86
0x87
0x88
0x89
0x8A
0x8B
0x8C
N/A
N/A
N/A
9
0x91
0x92
0x93
0x94
0x95
0x96
0x97
0x98
0x99
0x9A
0x9B
N/A
N/A
N/A
N/A
10
0xA1
0xA2
0xA3
0xA4
0xA5
0xA6
0xA7
0xA8
0xA9
0xAA
N/A
N/A
N/A
N/A
N/A
11
0xB1
0xB2
0xB3
0xB4
0xB5
0xB6
0xB7
0xB8
0xB9
N/A
N/A
N/A
N/A
N/A
N/A
12
0xC1
0xC2
0xC3
0xC4
0xC5
0xC6
0xC7
0xC8
N/A
N/A
N/A
N/A
N/A
N/A
N/A
13
0xD1
0xD2
0xD3
0xD4
0xD5
0xD6
0xD7
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
14
0xE1
0xE2
0xE3
0xE4
0xE5
0xE6
0xE7
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
15
0xF1
0xF2
0xF3
0xF4
0xF5
0xF6
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
30
Wall_SNo: Product Number code assigned to the product
10x10 Video Wall Model : ( 1 ~ 100)
Set Number
Data
1
0x01
2
0x02
...
...
99
0x63
100
0x64
•• Ack
Header
Command
0xAA
0xFF
ID
Data length
Ack/Nak
r-CMD
Val1
Val2
4
'A'
0x89
Wall_Div
Wall_SNo
Checksum
•• Nak
Header
Command
0xAA
0xFF
ID
Data length
Ack/Nak
r-CMD
Val1
3
'N'
0x89
ERR
Checksum
"ERR": A code showing what error has occurred
31
Chapter 03
Connecting and Using a Source Device
Before Connecting
Pre-connection Checkpoints
――Before connecting a source device, read the user manual provided with it.
The number and locations of ports on source devices may differ from device to device.
――Do not connect the power cable until all connections are completed.
Connecting the power cable during connection may damage the product.
――Check the types of ports at the back of the product you want to connect.
32
Before connecting cables
――The colour and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality.
3
Unfasten the screws, then remove the cover.
2
Remove the appropriate silicon bar for the
thickness of the cable to connect.
Different hole sizes and corresponding cable
thickness for each:
* JACK
Silicone-Bar
4
5
Insert the appropriate cable into the hole from
which the Silicone-Bar was removed.
The cable should be connected as shown.
Close the cover, then fasten the screws.
――After all the cables are connected, make sure to
close the cover and fasten the screws to ensure it is
water tight.
――Recommended torque : 10 - 12 kgf.cm
――7 Ø hole x 2: Insert the 7 Ø cable
――5.5 Ø hole x 6 : Insert the 5.5 Ø cable
――3 Ø hole x 4 : Insert the 3 Ø cable
* POWER INLET
――7 Ø hole x 1: Insert the 7 Ø cable
33
Connecting to a PC
Connection Using an HDMI Cable
――The appearance may differ depending on the product.
•• Do not connect the power cable before connecting all other cables.
――Connecting parts may differ in different products.
Ensure you connect a source device first before connecting the power cable.
•• A PC can be connected to the product in a variety of ways.
Select a connection method suitable for your PC.
――Connecting parts may differ in different products.
Connection Using an HDMI-DVI Cable
HDMI IN 1, HDMI IN 2
After connecting a computer to the product with an HDMI-DVI cable, make sure to configure the settings
as shown below to enable the video and audio from the computer.
――The appearance may differ depending on the product.
――Connecting parts may differ in different products.
34
Connecting to a Video Device
Connection Using an HDMI Cable
――The appearance may differ depending on the product.
•• Do not connect the power cable before connecting all other cables.
――Connecting parts may differ in different products.
Ensure you connect a source device first before connecting the power cable.
•• You can connect a video device to the product using a cable.
――Connecting parts may differ in different products.
――Press the SOURCE button on the remote control to change the source.
Using an HDMI cable or HDMI to DVI Cable (up to 1080p)
•• For better picture and audio quality, connect to a digital device using an HDMI cable.
•• An HDMI cable supports digital video and audio signals, and does not require an audio cable.
Connection Using an HDMI-DVI Cable
Supported resolutions include 1080p (50/60Hz), 720p (50/60Hz), 480p, and 576p.
•• The picture may not display normally (if at all) or the audio may not work if an external device that
uses an older version of HDMI mode is connected to the product. If such a problem occurs, ask the
manufacturer of the external device about the HDMI version and, if out of date, request an upgrade.
――The appearance may differ depending on the product.
•• Be sure to use an HDMI cable with a thickness of 14 mm or less.
――Connecting parts may differ in different products.
•• Be sure to purchase a certified HDMI cable. Otherwise, the picture may not display or a connection
error may occur.
•• A basic high-speed HDMI cable or one with ethernet is recommended.
This product does not support the ethernet function via HDMI.
HDMI IN 1, HDMI IN 2
HDMI IN 1, HDMI IN 2
35
Connecting the HDBase-T
――The appearance may differ depending on the product.
――Connecting parts may differ in different products.
――HDBase-T (Tx) transmits data from an external device to HDBase-T (Rx). Make sure to connect them directly using a LAN cable.
――Data transmission is not available if HDBase-T (Rx) is connected to HDBase-T (Tx) through a hub.
――HDBase-T works with unshielded twisted pair (UTP) or shielded twisted pair (STP) cables; but, to ensure CE compliance, STP cables and STP Connectors are required. Shielded cable and connectors are recommended to safeguard
against unpredictable environmental electrical noise which may impact performance. It is recommended to use an STP cable to maximize performance. Using a UTP cable or patch may decrease performance.
HDMI OUT
HDBase-T (Tx)
HDBT (LAN IN)
LAN
HDMI IN
HDMI OUT
LAN Cable
HDMI OUT
36
Connecting to an Audio System
Connecting the LAN Cable
――The appearance may differ depending on the product.
――The appearance may differ depending on the product.
――Connecting parts may differ in different products.
――Connecting parts may differ in different products.
AUDIO OUT
HDBT (LAN IN)
•• Use Cat7(*STP Type) cable for the connection.
*Shielded Twist Pair
37
Changing the Input source
Source allows you to select a variety of sources and change source device names.
You can display the screen of a source device connected to the product. Select a source from source list
to display the screen of the selected source.
――The input source can also be changed by using the SOURCE button on the remote control.
――The screen may not display correctly if an incorrect source is selected for the source device you want to
Source
convert to.
SOURCE → Source
Edit
Source
SOURCE → Source → u → Edit → ENTER E
Edit the name and device type of a connected external device.
MagicInfo S
Web Browser
HDMI 1
HDMI 2
•• The list can include the following source devices. Source devices on the list differ depending on the
selected source.
HDMI 1 / HDMI 2 / HDBT / Cable Box / Game Console / PC / Blu-ray player
•• You cannot edit the following sources.
MagicInfo S / URL Launcher / Web Browser
――The displayed image may differ depending on the model.
38
Web Browser
SOURCE → Source → Web Browser → ENTER E
Settings
SOURCE → Source → Web Browser → u → Settings → ENTER E
General
Hide Tabs and Toolbar automatically
If the browser tabs, menu or toolbar are not used for a while, they will automatically disappear. To make
them appear again, move the pointer or focus to the top of the screen.
•• Use / Do not use
Web Browser
Pop-up Blocker
Make your browsing experience more pleasant by blocking pop-up windows.
•• Use / Do not use
――The displayed image may differ depending on the model.
――Connect a LAN cable to access Internet from the product, similar to accessing the Internet from a computer.
Reset Settings
All your customised web Browser settings will be reset to their default values. Your bookmarks and
history won't be affected.
Search Engine
If you enter a keyword in the URL/keyword input field, Web Browser will open the Search Results page.
Choose the search engine you want to use.
•• Google / Bing
39
Privacy & Security
Blocked Pages
Security Mode
Blocked pages
Provides warnings about unsafe pages or blocks access to enhance Web Browser security.
Blocks access to pages that you have listed in Blocked pages.
This may slow the Web Browser down.
•• Use / Do not use
•• Use / Do not use
Blocked pages
Private Browsing
Block or unblock specific pages.
When Private Browsing is active, your browsing history won't be recorded.
•• Add
•• Use / Do not use
Do Not Track
Ask websites not to track you.
•• Use / Do not use
JavaScript
Allow all sites to run JavaScript for a better browsing experience.
•• Use / Do not use
Clear History
Clear your entire browsing history.
•• Clear History
Delete browsing data
Approved pages
Approved pages
Enables web access only to pages that you have approved.
•• Use / Do not use
Password for Approved pages
Set a password for managing Approved pages.
•• Set Password
Approved Pages
Approve specific pages or remove them from Approved pages.
•• Add
Delete all browsing data such as cookies, cached images and data.
Your bookmarks and history won't be affected.
•• Delete browsing data
40
Encoding
Choose an encoding method for web pages. The current setting is Auto.
•• Auto / Manual (Current : Unicode)
Refresh Options
SOURCE → Source → Web Browser → u → Refresh Options → ENTER E
Refresh Interval
Set the time for the web browser to wait before returning to the home page.
•• Off / 5 min / 10 min / 15 min / 30 min
Zoom1
Set the zoom scale to apply when the web browser is refreshed.
•• 50% / 75% / 100% / 125% / 150%
Home Page
Set the website to display when the web browser is refreshed.
•• Samsung Display / Custom
Custom
Enter the URL to set as the home page.
•• Enter URL
――Available only when Home Page is set to Custom.
41
Chapter 04
Using MDC
Multiple display control "MDC" is an application that allows you to easily control multiple display devices simultaneously using a PC.
- For details on how to use the MDC programme, refer to Help after installing the programme. The MDC programme is available on the website.
MDC Programme Installation/Uninstallation
Installation
Uninstallation
1
Select Settings > Control Panel on the Start menu and double-click Add/Delete Program.
2
Select MDC Unified from the list and click Change/Remove.
――MDC installation can be affected by the graphics card, mother board and network conditions.
1
Click the MDC Unified installation programme.
2
Select a language for installation. Next, click "OK".
3
When the "Welcome to the InstallShield Wizard for MDC_Unified" screen appears, click "Next".
4
In the "License Agreement" window displayed, select "I accept the terms in the license agreement"
and click "Next".
5
In the displayed "Customer Information" window, fill out all the information fields and click "Next".
6
In the displayed "Destination Folder" window, select the directory path you want to install the
programme in and click "Next".
――If the directory path is not specified, the programme will be installed in the default directory path.
7
In the displayed "Ready to Install the Program" window, check the directory path to install the
programme in and click "Install".
8
Installation progress will be displayed.
9
Click "Finish" in the displayed "InstallShield Wizard Complete" window.
――Select "Launch MDC Unified" and click "Finish" to run the MDC programme immediately.
10 The MDC Unified shortcut icon will be created on the desktop after installation.
――The MDC execution icon may not be displayed depending on the PC system or product specifications.
――Press F5 if the execution icon is not displayed.
42
Connecting to MDC
Using MDC via Ethernet
Enter the IP for the primary display device and connect the device to the PC. Display devices can be
connected to each other using a LAN cable.
Using MDC via RS-232C (serial data communications
standards)
An RS-232C serial cable must be connected to the serial ports on the PC and monitor.
――The appearance may differ depending on the product.
Connection using a direct LAN cable
――The appearance may differ depending on the product.
――Multiple products can be connected using the RJ45 (LAN OUT) port on the product and the LAN ports on the
HUB.
RS232C IN
Monitor 1
RS232C OUT
RS232C IN RS232C OUT
Computer
RJ45 (LAN OUT)
RS232C IN
Monitor 2
HUB
Monitor 1
Computer
Monitor 2
43
Connection using a cross LAN cable
――The appearance may differ depending on the product.
――Multiple products can be connected using the RS232C IN / OUT port on the product.
RS232C IN
Monitor 1
RS232C OUT
RJ45 (LAN OUT)
RS232C OUT
RS232C IN
Monitor 2
Computer
44
Chapter 05
Player feature
Accessible using the HOME button on the remote control.
Player
HOME
No.
Description
1
Select between internal or external memory.
2
Play content, templates and schedules configured on the server.
→ Player → ENTER E
Play a range of content such as channels with schedules assigned, templates or files.
Player
Internal Memory
Used
199.33 MB
1
Filter By: All
5
6
•• You can view whether the server is connected (approval) in the Player screen.
To view whether the server is connected when a Network Channel is running,
press INFO on the remote.
Available
4.26 GB(95%)
Options
No channels
2
Network Channel
3
Network File
4
1
Select Network Channel from the Player screen. The No channels message
appears if no channel has been registered in Network Channel.
2
Network Channel will run.
3
Play content stored on the server.
4
Play a template stored in the internal memory.
5
Select a content type as criterion to search for a desired content list.
6
Set different options for Player.
My Templates
Viewing content
――The displayed image may differ depending on the model.
――To use the Player feature, set Play via to MagicInfo in System.
1
Select either internal or external memory. The files saved in the selected memory appear.
2
Select the desired file. The content appears on the screen. (For more information on compatible file
formats, see the “File formats compatible with Player” section.)
45
When content is running
Available menu
Press the TOOLS button on the remote control during content playback to configure settings.
Control buttons on the remote
Menu
Description
You can use buttons on your remote control to play, pause, or skip between content on the playlist.
Playlist
View a list of content items currently playing.
Button
Picture Mode
Customises the screen settings for the content currently playing.
Function
TOOLS
Brings up the menu bar.
Sound Mode
Customises the audio settings for the content currently playing.
INFO
Displays the information of the content.
Repeat
Set the repeat mode.
►
Goes to next file or page.
Background Music
Set the background music to be played when content is running.
◄
Goes to previous file or page.
Reset
Reset the background music.
E/∆/³
Plays or pauses slide show or video content.
Pause
Pause the background music.
´
Stops displaying content and goes to the Player screen.
Prev
Play the previous background music on the list.
π
Rewinds the video content.
Next
Play the next background music on the list.
µ
Fast forwards the video content.
――Reset, Pause, Prev, Next only appear when the background music is set.
46
File Formats Compatible with Player
•• Supported file systems include FAT32 and NTFS.
•• A file with a vertical and horizontal resolution larger than the maximum resolution cannot be played.
Check the vertical and horizontal resolution of the file.
•• Check the supported video and audio Codec types and Versions.
•• Check the supported file versions.
‒‒ PowerPoint version up to 97 – 2007 is supported
Sound output restrictions
•• More than one sound output cannot be used.
•• Playback priority: network BGM > local BGM > video file in the main frame selected by the user
――Network BGM: Settings can be configured in step 1 when creating a server schedule.
――Local BGM: BGM settings can be configured using the tools displayed after the TOOLS button is pressed
during Player playback.
――User-selected main frame: Main frame settings can be configured in step 2 when creating a server
schedule.
•• Only the last USB device that was connected is recognised.
Template files and LFD(.lfd) files
Network Schedule Multiframe
Playback restrictions
•• A maximum of two video files (Video) can be played simultaneously.
•• In portrait playback mode, only one video file can be played at a time.
•• For Office files (PPT and Word files) and PDF files, only one file type is supported at a time.
•• LFD(.lfd) files are not supported.
Restrictions
•• Ensure a distributed folder (content / schedules) exists in Internal / USB memory.
Playback restrictions
•• A maximum of two video (Video) files can be played.
•• For Office files (PPT and Word files) and PDF files, only one file type is supported at a time.
•• Multiple videos (Video) cannot be played on a single display of a video wall simultaneously.
Sound output restrictions
•• More than one sound output cannot be used.
•• Playback priority: network BGM > local BGM > video file in the main frame selected by the user
47
Contents
File Extension
Container
Video Codec
*.avi
AVI
*.mkv
MKV
*.asf
ASF
*.wmv
MP4
*.mp4
3GP
*.mov
MOV
MVC
*.3gp
FLV
Divx 3.11 / 4 / 5 / 6
*.vro
VRO
*.mpg
VOB
*.mpeg
PS
H.264 BP/MP/HP
4096x2160
Bit rate
(fps)
(Mbps)
4096X2160: 24
40
60
80
Motion JPEG
30
80
60
20
1920 x 1080
SVAF
MPEG1
ADPCM(IMA, MS)
AAC
HE-AAC
WMA
MPEG(MP3)
DTS (Core , LBR)
Window Media Video v9 (VC1)
TS
AC3
DD+
MPEG4 SP/ASP
*.tp
Audio Codec
LPCM
HEVC (H.265 - Main, Main10, Main4:2:2 10)
MPEG2
G.711(A-Law, μ-Law)
Microsoft MPEG-4 v1, v2, v3
*.mov
Frame rate
3840X2160: 30
*.ts
*.trp
Resolution
30
20
Window Media Video v7(WMV1),v8(WMV2)
*.flv
*.vob
*.svi
H 263 Sorenson
*.m2ts
VP6
*.mts
*.divx
*.webm
WebM
VP8
1920x1080
90
20
VP9
4096x2160
4096X2160: 24
20
Vorbis
3840X2160: 30
*.rmvb
RMVB
RV8/9/10 (RV30/40)
1920x1080
60
20
RealAudio 6
48
Video
•• 3D video is not supported.
•• Content with a resolution larger than the resolution specified in
the table above is not supported.
•• Video content with a Bit rate or Frame rate larger than the rate
specified in the table above can cause choppy video during
playback.
•• Video content will not play, or not play correctly, if there is an
error in the content or the container.
•• Some USB/digital camera devices may not be compatible with
the player.
Audio
•• Audio content with a Bit rate or Frame rate larger than the rate
specified in the table above can cause choppy audio during
playback.
•• Audio content will not play, or not play correctly, if there is an
error in the content or the container.
•• Some USB/digital camera devices may not be compatible with
the player.
•• Supports up to WMA 10 Pro 5.1 channel. WMA lossless audio is
not supported.
Image
•• Compatible image file format : JPEG, PNG, BMP
――32-bit, 24-bit and 8-bit BMP files are supported.
•• Supported maximum resolution : 4096 x 4096
•• Supported maximum file size: 20MB
•• Supported image effects : 9 effects
(Fade1, Fade2, Blind, Spiral, Checker, Linear, Stairs, Wipe,
Random)
•• QCELP, AMR NB/WB are not supported.
•• Supports up to H.264, Level 4.1
•• H.264 FMO / ASO / RS, VC1 SP / AP L4 and AVCHD are not
supported.
•• For all Video codecs except MVC, VP8, VP6:
‒‒ Below 1280 x 720: 60 frame max
‒‒ Above 1280 x 720: 30 frame max
•• GMC 2 or higher is not supported.
•• Supports only BD MVC Spec.
•• Only one video file can play at a time if video files on the monitor
use incompatible codecs or the resolution is 1080 x 1920.
•• When a single video file is playing, Seamless mode is not
supported under the following conditions:
‒‒ Incompatible codec (MVC, VP3, MJPEG) ↔ Incompatible codec
‒‒ Incompatible codec ↔ Compatible codec
‒‒ The resolution is different from that of the monitor
‒‒ The frequency is different from that of the monitor
49
Power Point
•• Compatible document file formats
‒‒ Extension : ppt, pptx
‒‒ Version : Office 97 ~ Office 2007
•• Functions not supported
PDF
WORD
•• Compatible document file formats
‒‒ Extension : pdf
•• Functions not supported
•• Compatible document file formats
‒‒ Extension : .doc, .docx
‒‒ Version : Office 97 ~ Office 2007
•• Functions not supported
‒‒ Animation effect
‒‒ Content less than 1 pixel not supported because of
performance degradation issue.
‒‒ 3D shapes (which will be displayed in 2D)
‒‒ Masked Image, Tiled Image content not supported.
‒‒ Some paragraph styles
‒‒ Header and footer (some subitems are not supported)
‒‒ Content with Rotated Text, not supported.
‒‒ Word Art
‒‒ Word Art
‒‒ 3D Shadow Effects not supported.
‒‒ Align
‒‒ Align
‒‒ Some characters not supported
A group alignment error may occur
‒‒ Office 2007
SmartArt is not fully supported. 97 out of 115 subitems are
supported.
(Special characters may be corrupted)
‒‒ Page background effect
A group alignment error may occur
‒‒ 3D shapes (which will be displayed in 2D)
‒‒ Office 2007
SmartArt is not fully supported. 97 out of 115 subitems are
supported.
‒‒ Object insertion
‒‒ Charts
‒‒ Half-width characters
‒‒ Half-width characters
‒‒ Letter spacing
‒‒ Letter spacing
‒‒ Charts
‒‒ Vertical text
‒‒ Vertical text
Some subitems are not supported
Some subitems are not supported
‒‒ Slide notes and handout
‒‒ Slide notes and handout
50
Template files
•• Creation/editing/playback are only available in Template.
LFD
•• Supported in Network Channel
•• Compatible document file formats
‒‒ Extension : .lfd
51
Schedule
HOME
You can check the content’s playback schedule on the server, imported from an external storage, or on a
mobile device.
No.
→ Schedule → ENTER E
Schedule
Connected
1
Network
Description
1
Select between server and external memory.
2
View weekly schedule of content playback.
Select to view detailed information of each event.
Sun
Mon
Tue
Wed
Thu
Fri
Sat
AM
3
View a thumbnail image and brief information of the content.
2
Information
All day
All day
All day
PM
All day
All day
Location:
Internal Memory
3
Date:
**-**-**** ~
**-**-****
Repeat:
Daily
Time:
All day
AM
――The displayed image may differ depending on the model.
52
Clone Product
Export settings on the product to an external storage device. You can also import settings from an
external storage device.
This option is useful when assigning the same settings to several products.
HOME
→ Clone Product → ENTER E
When a duplicate file is not found on the external storage device
1
Connect the external storage device, then run the Clone Product function.
2
The No cloning file found on the external storage device. Export this device's settings to the external
storage device? message appears.
3
Select Export to export the settings.
When a duplicate file is found on the external storage device
Clone Product
1
Connect the external storage device, then run the Clone Product function.
2
The Cloning file found. Please select an option. message appears.
Run the Import from External Storage or Export to External Storage function.
――The displayed image may differ depending on the model.
‒‒ Import from External Storage: Copy settings saved on an external storage device to the product.
‒‒ Export to External Storage: Copy settings on the product to an external storage device.
――After configuration is complete, the product is rebooted automatically.
53
ID Settings
HOME
→ ID Settings → ENTER E
Assign an ID to a set.
Device ID
Enter the ID number of the product connected to the input cable for input signal reception. (Range:
0~224)
――Press u/d to select a number, and press E.
――Enter the number you want using the number buttons on the remote control.
Device ID Auto Set
ID Settings
This feature automatically allots an ID number to a device connected via an RS232C cable.
When multiple devices are connected, enable the feature on either the first or last device.
――This function is only available on the first device within an RS-232C daisy chain.
――The displayed image may differ depending on the model.
PC Connection Cable
Select a method to connect to MDC to receive the MDC signal.
•• RS232C cable
Communicate with MDC via the RS232C-stereo cable.
•• RJ-45 (LAN)/Wi-Fi Network
Communicate with MDC via the RJ45 cable or a Wi-Fi network.
――For the models (LH55OHFPVBC, LH46OHFPVBC) that do not support wireless communication, only the RJ45(LAN) menu appears.
54
Video Wall
Customise the layout of multiple displays that are connected to form a video wall.
HOME
To display multiple images, refer to MDC Help or the MagicInfo user guide. Some models may not support
the MagicInfo function.
→ Video Wall → ENTER E
In addition, display part of a whole picture or repeat the same picture on each of the connected multiple
displays.
Video Wall
You can activate or deactivate Video Wall.
To organise a video wall, select On.
•• Off / On
Video Wall
Horizontal x Vertical
This feature automatically splits a videowall display based on a videowall matrix configuration.
――The displayed image may differ depending on the model.
Enter the videowall matrix.
The videowall display is split based on the configured matrix. The number of vertical or horizontal display
devices can be set within the range 1 and 15.
――A videowall display can be split into a maximum of 100 screens.
――The Horizontal x Vertical option is only enabled when Video Wall is set to On.
Screen Position
To rearrange split screens, adjust the number for each product in the matrix using the Screen Position
feature.
Selecting Screen Position will display the videowall matrix with the numbers assigned to the products
that form the videowall.
To rearrange products, use the direction buttons on the remote control to move a product to another
desired number. Press the E button.
――Screen Position allows you to split the screen into a maximum of 100 views (15x15).
――The Screen Position option is only enabled when Video Wall is set to On.
――To use the function, make sure Horizontal x Vertical is configured.
55
Format
Select how to display images on the videowall display.
•• Full: Display images in full screen with no margin.
•• Natural: Display images in the original aspect ratio without enlarging or reducing the size.
――The Format option is only enabled when Video Wall is set to On.
56
Network Status
HOME
Check the current network and Internet connection.
→ Network Status → ENTER E
Network Status
――The displayed image may differ depending on the model.
57
Picture Mode
Select a picture mode (Picture Mode) suitable for the environment where the product will be used.
HOME
•• Shops & Shopping Centres
→ Picture Mode → ENTER E
Videos/Images mode improves the picture quality of the video device. Text mode improves the picture
quality of the computer.
Suitable for shopping malls.
‒‒ Select either Videos/Images or Text depending on the picture mode.
•• Offices & Schools
Suitable for offices and schools.
‒‒ Select either Videos/Images or Text depending on the picture mode.
•• Terminals & Stations
Suitable for bus terminals and train stations.
Picture Mode
‒‒ Select either Videos/Images or Text depending on the picture mode.
•• Video Wall
Suitable for environments where videowall display are used.
――The displayed image may differ depending on the model.
‒‒ Select either Videos/Images or Text depending on the picture mode.
•• Calibration
In this mode, the brightness, colour, gamma and uniformity settings customised using the colour
calibration programme Color Expert are applied.
‒‒ To apply the Calibration mode properly, make sure you configure the picture quality settings,
such as brightness, colour, gamma and uniformity, using the colour calibration programme Color
Expert.
‒‒ To download the Color Expert programme, visit www.samsung.com/displaysolutions.
58
On/Off Timer
HOME
→ On/Off Timer → ENTER E
――You must set Clock Set before you can use this feature.
On Timer
Set On Timer so that your product turns on automatically at a time and on a day of your choosing.
The power is turned on with the specified volume or input source.
On Timer: Set the on timer by making a selection from one of the seven options. Ensure you set the
current time first.
(On Timer 1 ~ On Timer 7)
•• Setup: Select Off, Once, Everyday, Mon~Fri, Mon~Sat, Sat~Sun or Manual. If you select Manual, you
can choose the days you want On Timer to turn on your product.
On/Off Timer
――The displayed image may differ depending on the model.
‒‒ The check mark indicates days you’ve selected.
•• Time: Set the hour and minute. Use the number buttons or the up and down arrow keys to enter
numbers. Use the left and right arrow buttons to change entry fields.
•• Volume: Set the desired volume level. Use the up and down arrow buttons to change the volume
level.
•• Source: Select the input source of your choice.
•• Content (when the Source is set to Internal/USB): From the USB device or internal memory, select a
file (e.g. music, photo, or video) to play just after the product is turned on.
――This function is available only when a USB device is connected.
――If there is no music file on the USB device or you don’t select a folder containing a music file, the Timer
function does not operate correctly.
――If there is only one photo file in the USB, the Slide Show will not play.
――If a folder name is too long, the folder cannot be selected.
――Each USB you use is assigned its own folder. When using more than one of the same type of USB, make sure
the folders assigned to each USB have different names.
――We recommend that you use a USB memory stick and a multi card reader when using On Timer.
――The On Timer function may not work with USB devices with a built-in battery, MP3 players, or PMPs made by
some manufacturers because the product can take too long to recognise these devices.
59
Off Timer
Set the off timer (Off Timer) by making a selection from one of the seven options. (Off Timer 1 ~ Off Timer
7)
•• Setup: Select Off, Once, Everyday, Mon~Fri, Mon~Sat, Sat~Sun or Manual. If you select Manual, you
can choose the days you want Off Timer to turn off your product.
‒‒ The check mark indicates days you’ve selected.
•• Time: Set the hour and minute. Use the number buttons or the up and down arrow keys to enter
numbers. Use the left and right arrow buttons to change entry fields.
Holiday Management
Timer will be disabled during a period specified as a holiday.
•• Add Holiday: Specify the period you want to add as a holiday.
Select the start and end dates of the holiday you want to add using the u/d buttons, and click the
Done button.
The period will be added to the list of holidays.
‒‒ Start: Set the start date of the holiday.
‒‒ End: Set the end date of the holiday.
•• Delete: Delete selected items from the list of holidays.
•• Edit: Select a holiday item and then change the date.
•• Set Applied Timer: Set the On Timer and Off Timer to not activate on public holidays.
‒‒ Press E to select the On Timer and Off Timer settings you do not want to activate.
‒‒ The selected On Timer and Off Timer will not activate.
60
Ticker
HOME
Input text while a video or image is displayed and display the text on the screen.
•• Off / On
→ Ticker → ENTER E
•• Message: Enter a message to display on the screen.
•• Time: Set the Start Time and End Time to display a Message.
•• Font options: Specify the text font and colour for the message.
•• Position: Select an orientation to display a Message.
•• Scroll: Specify the scroll Direction and Speed for the message.
•• Preview: Preview configured caption settings.
Ticker
――The displayed image may differ depending on the model.
61
URL Launcher
HOME
For details on how to use the URL Launcher feature, contact the dealer the product was purchased from.
――To use the URL Launcher feature, set Play via to URL Launcher in System.
→ URL Launcher → ENTER E
URL Launcher
――The displayed image may differ depending on the model.
62
URL Launcher Settings
HOME
→ URL Launcher Settings → ENTER E
•• Install Web App: Enter URL to install the web application.
•• Install from USB Device: Install the web application from the USB storage device.
•• Uninstall: Remove the installed web application.
•• Timeout Setting: Set the timeout period for connecting to the URL.
•• Developer Mode: Enable developer mode.
URL Launcher
Settings
――The displayed image may differ depending on the model.
63
Approving a connected device from the server
――First configure the server Server Network Settings before device approval.
1
Access the server you have assigned to your device.
2
Enter your ID and password to log in.
4
Select Unapproved from the sub-menus.
5
Select the device from the list and click the Approve button.
6
3
Select Device from the top menu bar.
Enter the information required to approve the device.
――Device Name: Enter the device name.
――Device Group: Select
to specify the group.
――Location: Enter the current location of the device.
――Expired: Set expiry date for the device's approval. If you do not want to set the expiry date, select Never
expired.
――Pressing the INFO button on the remote when a network schedule is running will display the details of the
schedule. Check that the correct device has been selected by viewing the device ID in the details.
64
Setting the current time
A schedule may not run if the time set on the device is different from the server's current time.
7
Select the All menu to check that the device has been registered.
8
When the device is approved by the server, the schedule registered in the selected group will be
downloaded to the device. The schedule will run after it is downloaded.
――For further details on how to configure a schedule, refer to the <MagicInfo Lite Server user's manual>.
――If a device is deleted from the list of devices approved by the server, the device will reboot to reset its
settings.
1
Select Device from the side menu bar.
2
Select your device.
3
Select Edit → Setup.
4
Select Time Zone.
――When connecting to the server for the first time, the time on the product is set using the GMT time of the
region where the server is installed.
――The time on the product can be changed from the server as shown in step 3.
――Turning the product off and then on again will restore the time setting on the product to the last time that
was set from the server.
――For further details on how to manage the time (scheduling, holiday management, etc.), refer to the <MagicInfo
Lite Server user's manual>.
65
Chapter 06
Screen Adjustment
Configure the Picture settings (Backlight, Colour Tone, etc.).
The layout of the Picture menu options may vary depending on the product.
Picture Mode
Select a picture mode (Picture Mode) suitable for the environment where the product will be used.
Videos/Images mode improves the picture quality of the video device. Text mode improves the picture quality of the computer.
•• Shops & Shopping Centres
MENU m → Picture → Picture Mode → ENTER E
Suitable for shopping malls.
‒‒ Select either Videos/Images or Text depending on the picture mode.
Picture
Picture Mode
·
·
·
•• Offices & Schools
Shops & Shopping Centres
Backlight
100
Contrast
70
Brightness
45
Sharpness
65
Colour
50
Tint (G/R)
G50
R50
Suitable for offices and schools.
‒‒ Select either Videos/Images or Text depending on the picture mode.
•• Terminals & Stations
Suitable for bus terminals and train stations.
‒‒ Select either Videos/Images or Text depending on the picture mode.
•• Video Wall
Suitable for environments where videowall display are used.
‒‒ Select either Videos/Images or Text depending on the picture mode.
•• Calibration
In this mode, the brightness, colour, gamma and uniformity settings customised using the colour calibration programme
Color Expert are applied.
‒‒ To apply the Calibration mode properly, make sure you configure the picture quality settings, such as brightness, colour,
gamma and uniformity, using the colour calibration programme Color Expert.
‒‒ To download the Color Expert programme, visit www.samsung.com/displaysolutions.
――The displayed image may differ depending on the model.
66
Backlight / Contrast / Brightness /
Sharpness / Colour / Tint (G/R)
Your product has several options for adjusting picture quality.
――When you make changes to Backlight, Contrast, Brightness, Sharpness, Colour or Tint (G/R), the OSD will be adjusted accordingly.
――You can adjust and store settings for each external device you have connected to an input on the product.
――Lowering picture brightness reduces power consumption.
MENU m → Picture → ENTER E
Picture
Picture Mode
·
·
·
Shops & Shopping Centres
Backlight
100
Contrast
70
Brightness
45
Sharpness
65
Colour
50
Tint (G/R)
G50
R50
――The displayed image may differ depending on the model.
67
Colour Temperature
It sets colour temperature. The value and temperature increase simultaneously, so the ratio of blue colour rises. (Range:
2800K–16000K)
――Enabled when Colour Tone is set to Off.
MENU m → Picture → Colour Temperature → ENTER E
――Colour Temperature is disabled if Picture Mode is set to Calibration.
Picture
Colour Temperature
16000K
――The displayed image may differ depending on the model.
White Balance
2 Point
Adjust the colour temperature for a more natural picture.
MENU m → Picture → White Balance → ENTER E
Picture
White Balance
•• R-Offset / G-Offset / B-Offset: Adjust each colour’s (red, green, blue) darkness.
•• R-Gain / G-Gain / B-Gain: Adjust each colour’s (red, green, blue) brightness.
•• Reset: Suitable for environments where videowall display are used.
10 Point
Controls the white balance in 10 point interval by adjusting the red, green, and blue brightness.
•• Off / On
――The displayed image may differ depending on the model.
Interval: Select interval to adjust.
Red: Adjust the red level.
Green: Adjust the green level.
Blue: Adjust the blue level.
Reset: Suitable for environments where videowall display are used.
――Some external devices may not support this function.
――Enabled when Picture Mode is set to Offices & Schools (Videos/Images).
68
Gamma
Adjust the primary colour intensity.
――If Picture Mode is set to Calibration, Gamma is disabled.
MENU m → Picture → Gamma → ENTER E
Picture
Gamma
0
――The displayed image may differ depending on the model.
Calibrated value
Select whether to apply the brightness, colour, gamma and uniformity settings customised using the colour calibration
programme Color Expert to the Information and Advertisement modes.
MENU m → Picture → Calibrated value → ENTER E
――To download the Color Expert programme, visit www.samsung.com/displaysolutions.
•• Don't apply / Apply
――If Picture Mode is set to Calibration, Calibrated value is disabled.
Picture
Calibrated value
Don't apply
――The displayed image may differ depending on the model.
69
――If Picture Mode is set to Calibration, Advanced Settings is disabled.
Advanced Settings
Dynamic Contrast
MENU m → Picture → Advanced Settings → ENTER E
Adjust the screen contrast.
Advanced Settings
Dynamic Contrast
•• Off / Low / Medium / High
High
Black Tone
Darkest
Flesh Tone
0
RGB Only Mode
Colour Space
Off
Native
Select the black level to adjust the screen depth.
•• Off / Dark / Darker / Darkest
Flesh Tone
Emphasise pink Flesh Tone.
HDMI UHD Color
Motion Lighting
Black Tone
On
RGB Only Mode
Displays the Red, Green and Blue colour for making fine adjustments to the hue and saturation.
――The displayed image may differ depending on the model.
•• Off / Red / Green / Blue
Colour Space
Adjusts the range and variety of colours (the colour space) available to create images.
•• Auto / Native / Custom
――To adjust Colour, Red, Green, Blue and Reset, set Colour Space to Custom.
70
HDMI UHD Color
Advanced Settings
Enable to optimise picture quality for HDMI UHD connection.
High
•• HDMI1 (Off / On)
Black Tone
Darkest
•• HDMI2 (Off / On)
Flesh Tone
0
Dynamic Contrast
RGB Only Mode
Colour Space
Off
Native
HDMI UHD Color
Motion Lighting
Motion Lighting
Reduces power consumption by reducing screen brightness when the picture on the screen is in motion.
•• Off / On
――Enabled when Picture Mode is set to Shops & Shopping Centres (Text).
On
――The displayed image may differ depending on the model.
71
Picture Options
Colour Tone
If Picture Mode is set to Text
MENU m → Picture → Picture Options → ENTER E
•• Off / Cool / Standard / Warm
If Picture Mode is set to Videos/Images
Picture Options
Colour Tone
•• Off / Cool / Standard / Warm1 / Warm2
Off
Digital Clean View
Auto
HDMI Black Level
Auto
Film Mode
Off
Dynamic Backlight
Off
――If Picture Mode is set to Calibration, Colour Tone is disabled.
――Settings can be adjusted and stored for each external device connected to an input on the product.
Digital Clean View
Reduce picture noise to avoid distractions such as flickering.
•• Off / Auto
――The displayed image may differ depending on the model.
72
HDMI Black Level
Picture Options
Colour Tone
Selects the black level on the screen to adjust the screen depth.
Off
Digital Clean View
Auto
HDMI Black Level
Auto
Film Mode
Off
Dynamic Backlight
Off
――The displayed image may differ depending on the model.
•• Auto / Low / Normal
――Available only in HDMI 1 and HDMI 2 mode (AV Timing : 480p, 576p, 720p, 1080i, 1080p).
Film Mode
Make frame transitions from older video sources smoother. This function is only available when the input signal is TV, AV,
Component (480i, 1080i), or HDMI (1080i).
•• Off / Auto1 / Auto2
Dynamic Backlight
Automatically adjust the backlight to provide the best possible screen contrast under the current conditions.
•• Off / On
73
Picture Size
choose size and aspect ratio picture displayed on screen.
MENU m → Picture → Picture Size → ENTER E
Different screen adjustment options are displayed depending on the current input source.
Picture Size
Picture Size
Picture Size
――Available ports may differ depending on the model.
16:9 Standard
· Fit to Screen
· Zoom/Position
•• 16:9 Standard: Sets the picture to 16:9 Standard wide mode.
•• Custom: Changes the resolution to suit the user's preferences.
•• 4:3: Sets the picture to basic (4:3) mode.
――Do not set your product to 4:3 format for a long time.
The borders displayed on the left and right, or top and bottom of the screen may cause image retention (screen burn) which is not
covered by the warranty.
――The displayed image may differ depending on the model.
Fit to Screen
Adjusts the picture position. When selected, the full programme image will be displayed. No part of the image will be cut off.
•• Off / On / Auto
Zoom/Position
Adjusts the picture zoom and position. This option is available when the input source is set to HDMI 1, HDMI 2 (1080i/1080p).
Picture Size must be set to Custom for the option to be available.
――If you want to reset the picture to its original position, select Reset in the Zoom/Position screen. The picture will be set to its default
position.
74
Picture Off
Selecting Picture Off switches off the screen. The volume is not disabled.
To switch the screen on, press any button other than the volume button.
MENU m → Picture → Picture Off → ENTER E
Picture
Picture Off
――The displayed image may differ depending on the model.
Reset Picture
Resets your current picture mode to its default settings.
MENU m → Picture → Reset Picture → ENTER E
Picture
Reset Picture
――The displayed image may differ depending on the model.
75
Chapter 07
OnScreen Display
Display Orientation
Onscreen Menu Orientation
Configure the menu screen.
MENU m → OnScreen Display → Display Orientation → ENTER E
•• Landscape: Display the menu in landscape mode (default).
•• Portrait: Display the menu in portrait mode on the right side of the product screen.
Display Orientation
Onscreen Menu Orientation
Landscape
Source Content Orientation
Source Content Orientation
Landscape
Rotate the product screen orientation.
Aspect Ratio
Full Screen
――The displayed image may differ depending on the model.
•• Landscape: Display the screen in landscape mode (default).
•• Portrait: Display the screen in portrait mode.
Aspect Ratio
Set the rotated screen to be either full screen or original.
•• Full Screen: Display the rotated screen in full screen.
•• Original ratio: Display the rotated screen in the original aspect ratio.
――Available only when Source Content Orientation is set to Portrait.
76
Screen Protection
Auto Protection Time
MENU m → OnScreen Display → Screen Protection → ENTER E
If the screen displays a still image for a certain period of time you define, the product activates the screen saver to prevent the
formation of burnt in ghost images on the screen.
•• Off / 2 hours / 4 hours / 8 hours / 10 hours
Screen Protection
Auto Protection Time
Screen Burn Protection
Off
Screen Burn Protection
To reduce the possibility of screen burn, this unit is equipped with Screen Burn Protection screen burn prevention technology.
Screen Burn Protection moves the picture slightly on the screen.
The Screen Burn Protection Time setting allows you to programme the time between movements of the picture in minutes.
――The displayed image may differ depending on the model.
Pixel Shift
Minimize image retention by finely moving pixels horizontally or vertically.
•• Pixel Shift (Off / On)
――Horizontal, Vertical and Time are enabled only when Pixel Shift is set to On.
•• Horizontal: Sets how many pixels the screen moves horizontally.
•• Vertical: Sets how many pixels the screen moves vertically.
•• Time: Set the time interval for performing the horizontal or vertical movement, respectively.
Available Pixel Shift Settings and Optimum Settings.
Available Settings
Optimum Settings
Horizontal (pixels)
0~4
4
Vertical (pixels)
0~4
4
Time (minute)
1 min ~ 4 min
4 min
――The Pixel Shift value may differ depending on the product size (inches) and mode.
――Displaying a still image or a 4:3 output for an extended period of time may cause image retention. This is not a defect in the product.
77
Timer
Screen Burn Protection
You can set the timer for Screen Burn Protection.
Pixel Shift
The Screen Burn Protection feature stops automatically after a specified period of time.
Timer
Timer
Immediate display
Off
Off
Repeat: Display the image retention-preventive pattern set in Mode at specified time intervals(Period).
Interval: Display the image retention-preventive pattern set in Mode for a specified period of time (from Start Time to End
Time).
――The displayed image may differ depending on the model.
――Mode, Period, Time, Start Time and End Time are enabled only when Timer is set to Repeat or Interval.
•• Mode: Select a screen protective pattern to display.
‒‒ Pixel: Pixels on the screen alternate black continuously.
‒‒ Rolling bar: A vertical bar moves left to right.
‒‒ Fading screen: The entire screen becomes brighter, then darker.
――The Rolling bar and Fading screen patterns appear only once regardless of the specified repeat period or time.
•• Period: Specify the time interval to activate the Screen Burn Protection function.
――The option is enabled when Repeat is selected for Timer.
•• Time: Specify the duration to keep the Screen Burn Protection function on.
――Enabled when Timer is set to Repeat and Mode is set to Pixel.
•• Start Time: Set the start time to activate the screen protection function.
――The option is enabled when Interval is selected for Timer.
•• End Time: Set the end time to deactivate the screen protection function.
――The option is enabled when Interval is selected for Timer.
78
Immediate display
Screen Burn Protection
Select the screen saver you want to display immediately.
•• Off / Pixel / Rolling bar / Fading screen
Pixel Shift
Timer
Immediate display
Off
――The displayed image may differ depending on the model.
79
Message Display
Source Info
Select whether to display the source OSD when the input source changes.
MENU m → OnScreen Display → Message Display → ENTER E
Message Display
•• Off / On
No Signal Message
Source Info
On
No Signal Message
On
MDC Message
On
Download Status Message
Off
Select whether to display the no-signal OSD when no signal is detected.
•• Off / On
MDC Message
Select whether to display the MDC OSD when the product is controlled by the MDC.
•• Off / On
――The displayed image may differ depending on the model.
Download Status Message
Select to display the status when downloading content from a server or other device.
•• Off / On
80
Language
Set the menu language.
――A change to the language setting will only be applied to the onscreen menu display. It will not be applied to other functions on your
PC.
MENU m → OnScreen Display → Language → ENTER E
OnScreen Display
Language
English
――The displayed image may differ depending on the model.
Reset OnScreen Display
This option returns the current settings under OnScreen Display to the default factory settings.
MENU m → OnScreen Display → Reset OnScreen Display → ENTER E
OnScreen Display
Reset OnScreen Display
――The displayed image may differ depending on the model.
81
Chapter 08
Network
Network Status
Open Network Settings
MENU m → Network → Network Status → ENTER E
MENU m → Network → Open Network Settings → ENTER E
You can check the current network and Internet status.
Configure network settings to use various smart hub features such as Internet search, content sharing
through a home network and feature updates.
Network type
•• Wireless / Wired
――For the models (LH55OHFPVBC, LH46OHFPVBC) that do not support wireless communication, the Wired
Network Settings menu appears.
82
Network Settings (Wired)
•• Depending on how your network is configured, you may be able to attach your product to your LAN
by connecting the LAN port on the back of your product directly to a network wall outlet using a LAN
cable.
See the diagram below. Note that the wall outlet is attached to a modem or router elsewhere in your
house.
Connecting to a Wired Network
There are three ways to attach your product to your LAN using cable.
•• You can attach your product to your LAN by connecting the LAN port on the back of your product to
an external modem using a LAN cable.
LAN
The LAN Port on the Wall
RJ45
See the diagram below.
LAN
External Modem
(ADSL / VDSL)
The Modem Port on the Wall
Modem Cable
RJ45
If you have a Dynamic Network, you should use an ADSL modem or router that supports the Dynamic
Host Configuration Protocol (DHCP). Modems and routers that support DHCP automatically provide the
IP address, subnet mask, gateway, and DNS values your product needs to access the Internet so you do
not have to enter them manually. Most home networks are Dynamic Networks.
LAN Cable
•• You can attach your product to your LAN by connecting the LAN port on the back of your product to
an IP Sharer which is connected to an external modem. Use LAN cable for the connection. See the
diagram below.
The Modem Port on the Wall
External Modem
(ADSL / VDSL)
Modem Cable
LAN Cable
LAN Cable
LAN
IP Sharer
(having DHCP server)
RJ45
Some networks require a Static IP address. If your network requires a Static IP address, you must enter
the IP address, subnet mask, gateway, and DNS values manually on your product Cable Setup Screen
when you set up the network connection. To get the IP address, subnet mask, gateway, and DNS values,
contact your Internet Service Provider (ISP).
If you have a Windows computer, you can also get these values through your computer.
――You can use ADSL modems that support DHCP if your network requires a Static IP address.
――ADSL modems that support DHCP also let you use Static IP addresses.
LAN Cable
83
2
In the pop-up menu that appears, click Status.
3
On the dialog that appears, click the Support tab.
Automatic Open Network Settings (Wired)
4
On the Support Tab, click the Details button. The Network connection values are displayed.
Connect to the network using a LAN cable.
How to set up manually
Set the network connection to use Internet services such as perform software upgrades.
Make sure a LAN cable is connected first.
How to set up automatically
1
Set Network type to Wired from the Open Network Settings page.
2
Press the Connect button to start Open Network Settings.
‒‒ The Connect button is only enabled when the LAN cable is properly connected.
3
The network test screen appears and verifies the network connection.
When the connection has been verified, the “Wired network and Internet connection completed.”
message appears.
――If the connection process fails, check the LAN port connection.
――If the automatic process cannot find the network connection values or if you want to set the connection
1
Set Network type to Wired from the Open Network Settings page.
2
Press the Connect button to start Open Network Settings.
‒‒ The Connect button is only enabled when the LAN cable is properly connected.
3
The network test screen appears and the verification process starts. Press Stop. The verification
process stops.
4
Select IP Settings on network connection screen. The IP Settings screen appears.
5
Select the field at the top, press E, and then set IP Settings to Enter manually. Repeat the entry
process for each field in the IP Address.
――Setting IP Settings to Enter manually automatically changes DNS Setting to Enter manually.
6
When done, select OK at the bottom of the page, and then press E. The network test screen
appears and the verification process starts.
7
When the connection has been verified, the “Wired network and Internet connection completed.”
message appears.
manually, go to the next section, network setup.
Manual Open Network Settings (Wired)
Offices may use static IP addresses.
If this is the case, ask the network administrator for the IP address, subnet mask, gateway and DNS server
address. Enter these values manually.
Getting the Network Connection Values
To view the Network connection values on most Windows computers, follow these steps.
1
Right click the Network icon on the bottom right of the screen.
84
Network Setting (Wireless)
Automatic Network Setup (Wireless)
――Models that do not support wireless communication: LH55OHFPVBC, LH46OHFPVBC
Most wireless networks have an optional security system that requires devices that access the network
to transmit an encrypted security code called an Access or Security Key. The Security Key is based on
a Pass Phrase, typically a word or a series of letters and numbers of a specified length you were asked
to enter when you set up security for your wireless network. If you use this method of setting up the
network connection, and have a Security Key for your wireless network, you will have to enter the Pass
Phrase during the the automatic or manual setup process.
Connecting to a Wireless Network
Wireless IP sharer
(router having DHCP server)
The LAN Port on the Wall
How to set up automatically
1
Set Network type to Wireless from the Open Network Settings page.
2
The Network function searches for available wireless networks. When done, it displays a list of the
available networks.
3
In the list of networks, press the ▲ or ▼ button to select a network, and then press the E button
twice.
LAN Cable
Samsung recommends using IEEE 802.11n. When you play video over a network connection, the video
may not play smoothly.
――Select a channel for the wireless IP sharer that is not currently being used. If the channel set for the wireless
IP sharer is currently being used by another device nearby, this will result in interference and communication
failure.
――Your product supports only the following wireless network security protocols.
If you select the Pure High-throughput (Greenfield) 802.11n mode and the Encryption type is set to WEP, TKIP
――If the desired wireless router does not appear, select Refresh to search again.
――If the router cannot be found after retrying, select the Stop button.
The Add Network button appears.
4
If the Enter password. screen appears, go to step 5. If you select a wireless router that does not have
security, go to step 7.
5
If the router has security, enter the Enter password. (Security key or PIN).
6
When done, use the right arrow button to move the cursor to Done, and then press E. The network
connection screen appears and the verification process starts.
or TKIP AES (WPS2Mixed) on your AP or wireless router, Samsung products will not support a connection in
compliance with new Wi-Fi certification specifications.
――If your wireless router supports WPS (Wi-Fi Protected Setup), you can connect to the network via PBC (Push
Button Configuration) or PIN (Personal Identification Number). WPS will automatically configure the SSID and
――A connection with the router is established, but the Internet cannot be accessed.
7
When the connection has been verified, the “Your wireless network and Internet connection are
setup and ready to use.” message appears.
WPA key in either mode.
――Connection Methods: You can setup the wireless network connection in three ways.
Auto Setup (Using the Auto Network Search function), Manual Setup, WPS(PBC)
85
Manual Network Setup (Wireless)
How to set up manually
Offices may use static IP addresses.
1
Set Network type to Wireless from the Open Network Settings page.
2
The Network function searches for available wireless networks. When done, it displays a list of the
available networks.
3
In the list of networks, press the u or d button to select a network, and then press the E button
twice.
If this is the case, ask the network administrator for the IP address, subnet mask, gateway and DNS server
address. Enter these values manually.
Getting the Network Connection Values
To view the Network connection values on most Windows computers, follow these steps.
――If the desired wireless router does not appear, select Refresh to search again.
1
Right click the Network icon on the bottom right of the screen.
――If the router cannot be found after retrying, select the Stop button.
2
In the pop-up menu that appears, click Status.
3
On the dialog that appears, click the Support tab.
4
On the Support Tab, click the Details button. The Network connection values are displayed.
4
If the Enter password. screen appears, go to step 5. If you select a wireless router that does not have
security, go to step 7.
5
If the router has security, enter the Enter password. (Security key or PIN).
6
When done, use the right arrow button to move the cursor to Done, and then press E. The network
connection screen appears and the verification process starts.
7
Select Stop while network connections are being attempted. This will stop the connection.
8
Select IP Settings on network connection screen. The IP Settings screen appears.
9
Select the field at the top, press E, and then set IP Settings to Enter manually. Repeat the entry
process for each field in the IP Address.
――Setting IP Settings to Enter manually automatically changes DNS Setting to Enter manually.
10 When done, select OK at the bottom of the page, and then press E. The network test screen
appears and the verification process starts.
11 When the connection has been verified, the “Your wireless network and Internet connection are
setup and ready to use.” message appears.
86
WPS(PBC)
How to set up using WPS(PBC)
If your router has a WPS(PBC) button, follow these steps.
1
Set Network type to Wireless from the Open Network Settings page.
2
Select WPS(PBC), press E, and then press E again.
3
Press the WPS(PBC) button on your router within 2 minutes. Your product automatically acquires all
the network setting values it needs and connects to your network.
4
The network connection screen appears, and network setup is done.
87
Server Network Settings
Proxy server
Set up your proxy server connection and related functions.
MENU m → Network → Server Network Settings → ENTER E
Connect to server
•• Address / Port / ID / Password
――Address / Port / ID and Password are enabled only when Proxy server is set to On.
To run Player connect to a network.
•• Server Address / SSL / Port
――If the SSL option is enabled, the server is configured to use https and data transfer is encrypted.
――Enter the server IP address and port number. Use 7001 as the port number. (If unable to connect to the server
using port number 7001, check with your server administrator to find the correct port number and then
change the port number.)
MagicInfo Mode
Select the appropriate MagicInfo Mode depending on the environment where you are using the product.
•• Lite / Premium
Server Access
Select a method to connect the server network.
•• Allow / Deny
FTP Mode
Specify the FTP operating mode.
•• Active / Passive
88
Wi-Fi Direct
To use this function, your mobile device
should be supported by the Wi-Fi Direct.
MENU m → Network → Wi-Fi Direct → ENTER E
Set to connect the product to wireless mobile devices. Using this function, you can connect wireless mobile devices with your product directly without a router.
――Models that do not support wireless communication: LH55OHFPVBC, LH46OHFPVBC
To connect your mobile device with your product using Wi-Fi Direct, follow these steps:
1
Go to Wi-Fi Direct screen. The product starts to search devices.
2
Turn on the Wi-Fi Direct function on your device. Select the desired Wi-Fi device.
•• PBC (Push Button Configuration): Press the WPS(PBC) button on your Wi-Fi device within 2 minutes. Your product automatically acquires all the network setting values
it needs and connects to your network.
•• PIN: Input the displayed PIN on your device.
――If you want to disconnect the device, select the connected Wi-Fi device, and then select Disconnected.
89
Mobile Device Manager
Allow other devices on your network, like smart phones and tablets, to share content with your product.
――Models that do not support wireless communication: LH55OHFPVBC, LH46OHFPVBC
Access Notification
Display a notification when a device is connected for the first time.
Turn off Access Notification to connect devices automatically.
――The Wi-Fi Direct feature is not supported currently.
•• Off / First Time Only / Always On
Mobile Device List
View and manage connected devices.
Device Name
MENU m → Network → Device Name → ENTER E
Select or enter a device name.
This name can be shown on network remote controls over the network.
•• [Signage]Display 1 ~ 6 / User Input
90
Chapter 09
System
Accessibility
Menu Transparency
Adjust transparency of menu box.
MENU m → System → Accessibility → ENTER E
System
Accessibility
Start Setup
•• High / Low
High Contrast
Set the background and font to high-contrast colours in Menu. Menu transparencies become opaque when the option is
selected.
•• Off / On
Time
Auto Source Switching
Enlarge
Power Control
Set whether to enlarge highlighted item in Menu.
Eco Solution
•• Off / On
Fan and Temperature
――The displayed image may differ depending on the model.
91
Start Setup
Go through the initial setup steps like you did the first time you used this product.
――Enter your 4 digit PIN number. The default PIN number is “0-0-0-0".
If you want to change the PIN number, use the Change PIN function.
MENU m → System → Start Setup → ENTER E
System
Accessibility
Start Setup
Time
Auto Source Switching
Power Control
Eco Solution
Fan and Temperature
――The displayed image may differ depending on the model.
92
Time
You can configure Clock Set or Sleep Timer. Configure various time-related settings.
MENU m → System → Time → ENTER E
Clock Set
――Press the INFO button if you want to view the current time.
Time
Select Clock Set. Select Date or Time, and then press E.
Use the number buttons to enter numbers or press the up and down arrow buttons. Use the left and right arrow buttons to
move from one entry field to the next. Press E when done.
Clock Set
――You can set the Date and Time directly by pressing the number buttons on the remote control.
NTP Settings
DST
On
Sleep Timer
Off
Power On Delay
――The displayed image may differ depending on the model.
0
NTP Settings
Set up the server URL and time zone to use the network time.
DST
Switches the DST (Daylight Saving Time) function on or off.
Off / On
•• Start Date: Set the start date of Daylight Saving Time.
•• End Date: Set the end date of Daylight Saving Time.
•• Time Offset: Select the correct time offset your timezone.
――Start Date, End Date and Time Offset are enabled only when DST is set to On.
Sleep Timer
Automatically shuts off the product after a preset period of time.
(Off / 30 min / 60 min / 90 min / 120 min / 150 min / 180 min)
――Use the up and down arrows to select a period of time, and then press E. To cancel Sleep Timer, select Off.
Power On Delay
When connecting multiple products, adjust the power-on time for each product to prevent power overload (within the range
0–50 seconds).
93
Auto Source Switching
Turning on the display with Auto Source Switching On, and the previous video source selection is not active, the display will
automatically search the different video input sources for active video.
MENU m → System → Auto Source Switching → ENTER E
Auto Source Switching
Auto Source Switching
When the Auto Source Switching is On, the display video source will automatically be searched for active video.
The Primary Source selection will be activated, if the current video source is not recognised.
Auto Source Switching
Off
Primary Source Recovery
Off
Primary Source
All
Secondary Source
HDMI 1
Secondary Source selection will become active, if no primary video source is available.
If both the primary and secondary input sources are not recognised, the display will perform two searches for an active source,
each search checking the primary and then secondary source. If both searches fail, the display will return to the first video
source and display a message indicating that there is no signal.
Primary Source Recovery
Select whether to restore the selected primary input source when a primary input source is connected.
――The Primary Source Recovery function is disabled if Primary Source is set to All.
――The displayed image may differ depending on the model.
Primary Source
Specify Primary Source for the automatic input source.
Secondary Source
Specify Secondary Source for the automatic input source.
――The Secondary Source function is disabled if Primary Source is set to All.
94
Power Control
Auto Power On
This feature automatically turns on the product as soon as it is plugged in. Pressing the power button is not needed.
MENU m → System → Power Control → ENTER E
•• Off / On
Power Control
Max. Power Saving
Auto Power On
Off
Max. Power Saving
On
•• Off / On
Standby Control
On
Standby Control
Network Standby
Off
Power Button
Power on only
Conserve power by turning off PC monitor when PC is not used for certain time.
You can set the screen standby mode to be applied when an input signal is received.
•• Auto
Power-saving mode will activate if no input signals are detected even though a source device is connected to the display.
The message No Signal will appear if no source device is connected.
――The displayed image may differ depending on the model.
•• Off
The message No Signal will appear if no input signals are detected.
――If No Signal is displayed although a source device is connected, check the cable connection.
――If No Signal Message is set to Off, the No Signal message does not appear.
If this is the case, set No Signal Message to On.
•• On
Power-saving mode will activate if no input signals are detected.
95
Network Standby
Power Control
This feature keeps the network power on when the product turns off.
Auto Power On
Off
Max. Power Saving
On
Standby Control
On
Network Standby
Off
Power Button
Power on only
•• Off / On
Power Button
The power button on the remote control
can be set to turn on the power or turn on or off the power.
•• Power On Only: Set the power button on the remote control
only to turn on the power.
•• Power On/Off: Set the power button on the remote control
to turn on or off the power.
――The displayed image may differ depending on the model.
96
Eco Solution
Brightness Limit
Limit the screen's maximum backlight level.
MENU m → System → Eco Solution → ENTER E
•• Off: Off allows you to use the maximum brightness available.
•• On: On prevents the use of maximum brightness and saves energy.
Eco Solution
Energy Saving Mode
Brightness Limit
Off
Energy Saving Mode
Off
Eco Sensor
Off
Screen Lamp Schedule
Off
Eco Sensor
No Signal Power Off
Off
To enhance your power savings, the picture settings will automatically adapt to the light in the room.
Auto Power Off
Off
Reduce the power consumption by adjusting the screen brightness.
•• Off / Low / Medium / High
•• Off / On
――Adjusting the Backlight setting under Picture while Eco Sensor is on will disable the Off.
――If the screen contrast is not sufficient, set the Eco Sensor to Off. If the Eco Sensor is Off, it may not comply with energy standards.
――The displayed image may differ depending on the model.
Min. Backlight
When Eco Sensor is On, you can manually adjust the minimum screen brightness. Min. Backlight is the darkest backlight mode.
Make sure the Min. Backlight setting is lower than the Backlight setting.
――If Eco Sensor is On, the display brightness may change (become slightly darker or brighter) depending on the surrounding light
intensity.
97
Screen Lamp Schedule
Eco Solution
Brightness Limit
Off
Energy Saving Mode
Off
Eco Sensor
Off
Screen Lamp Schedule
Off
No Signal Power Off
Off
Auto Power Off
Off
Screen Lamp Schedule
Enable or disable the lamp schedule.
•• Off / On
Schedule 1, Schedule 2
Time
The panel brightness will change to the brightness set in Lamp at a specified time.
Lamp
――The displayed image may differ depending on the model.
Adjust the panel brightness. A value closer to 100 makes the panel brighter.
•• 0 ~ 100
No Signal Power Off
Save power by turning the device off when no signal is received from any source.
•• Off / 15 min / 30 min / 60 min
――Disabled when an attached PC is in power saving mode.
――The product will automatically power off at a specified time. The time can be changed as required.
Auto Power Off
The product will automatically turn off if you don’t press a button on the remote or touch a button on product front panel within
select hours to prevent overheating.
•• Off / 4 hours / 6 hours / 8 hours
98
Fan and Temperature
MENU m → System → Fan and Temperature → ENTER E
Protects the product by detecting the fan speed and internal temperature.
Fan Control
Selects auto or manual for the fan speed settings.
System
•• Auto / Manual
Fan and Temperature
Fan Speed Setting
Sets the fan speed within a range of 0 and 100.
――Enabled when Fan Control is set to Manual.
――The displayed image may differ depending on the model.
Outdoor Mode
To use the product at a low temperature below 0˚C, make sure to set Outdoor Mode to "On."
This feature keeps the internal temperature of the product steady so that the product can start properly when it is powered on.
•• Off / On
――Do not disconnect the power cable when this feature is set to "On."
――The product consumes more power when it is turned off if this feature is set to "On" rather than to "Off."
Temperature Control
This function detects the internal temperature of the product. You can specify the temperature range that is acceptable.
The default temperature is set to 90 C.
The recommended operating temperature for this product is 75 to 90 C (based on an ambient temperature of 50 C).
――The screen will become darker if the current temperature exceeds the specified temperature limit. If the temperature continues to
rise, the product will power off to prevent overheating.
99
Input Device Manager
MENU m → System → Input Device Manager → ENTER E
Configure options for external input devices connected to the product.
Keyboard Language
Configure the key combination used to change the input language.
Input Device Manager
Keyboard Language
Keyboard type
Keyboard type
Specify the keyboard type.
Input Language Shortcut
Input Language Shortcut
Select shortcut keys for switching between input languages.
――The displayed image may differ depending on the model.
Play via
Select the appropriate Play via mode depending on the environment where you are using the product.
The home screen may be different depending on the setting.
•• MagicInfo / URL Launcher
MENU m → System → Play via → ENTER E
System
Play via
MagicInfo
――The displayed image may differ depending on the model.
100
Change PIN
MENU m → System → Change PIN → ENTER E
The Change PIN screen will appear.
Choose any 4 digits for your PIN and enter it in Enter New PIN. Reenter the same 4 digits in Confirm New PIN.
The product has memorised your new PIN.
――Default password: 0 - 0 - 0 - 0
System
Change PIN
――The displayed image may differ depending on the model.
101
Security
Safety Lock On
――Enter your 4 digit PIN number. The default PIN number is “0-0-0-0".
MENU m → System → Security → ENTER E
If you want to change the PIN number, use the Change PIN function.
All the menus and buttons of the product and remote control, except for the LOCK button on the remote control, will be locked
by the Safety Lock On function.
Security
To unlock the menus and buttons, press the LOCK button and then enter the password (default password: 0-0-0-0).
Safety Lock On
On
Power On Button
USB Auto Play Lock
On
Turn on this feature to enable the remote control's Power button to turn on the device while Safety Lock On is enabled.
Mobile Connection Lock
Off
Power On Button
Remote Management
•• Off / On
USB Auto Play Lock
Select whether to automatically play MagicInfo content saved on a connected USB device.
•• Off
――The displayed image may differ depending on the model.
Play MagicInfo content saved on the USB device automatically.
•• On
Do not play MagicInfo content saved on the USB device automatically.
――Connecting a USB device containing MagicInfo content displays "USB Auto Play Lock : On" for five seconds.
Mobile Connection Lock
Restrict other devices on your network, such as smart phones and tablets, to share content with your signage.
•• Off / On
Remote Management
You can Allow or Deny external commands to access your device via a network.
•• The changed setting remains even after the product is turned off and on using the Panel key or Power switch.
102
General
Smart Security
The security provided to protect your display device and connected storage devices against viruses includes.
MENU m → System → General → ENTER E
Scan
General
Inspect your display device and connected storage devices to check for viruses.
Smart Security
Anynet+ (HDMI-CEC)
On
HDMI Hot Plug
On
Custom Logo
Game Mode
Empty Storage
Isolated List
This is the list of items that have been Isolated for containing viruses.
Real-Time Monitoring
Off
Scans for viruses by monitoring the display device in real time.
Monitoring Results
Check the list of files, networks, and processes that have been blocked.
――The displayed image may differ depending on the model.
103
Anynet+ (HDMI-CEC)
General
Smart Security
Anynet+ (HDMI-CEC)
On
HDMI Hot Plug
On
•• Off / On
――You can only control Anynet+ devices using the product remote control, not the buttons on the product.
――The product remote control may not work under certain conditions. If this occurs, reselect the Anynet+ device.
Custom Logo
Game Mode
Anynet+ is a function that enables you to control all connected Samsung devices that support Anynet+ with your Samsung
product remote. The Anynet+ system can be used only with Samsung devices that have the Anynet+ feature. To be sure your
Samsung device has this feature, check if there is an Anynet+ logo on it.
――Anynet+ works when the AV device supporting Anynet+ is in the standby or on status.
Off
――Anynet+ supports up to 12 AV devices in total. Note that you can connect up to 3 devices of the same type.
Empty Storage
――The displayed image may differ depending on the model.
104
Troubleshooting for Anynet+
Problem
Anynet+ does not work.
Possible Solution
•• Check if the device is an Anynet+ device. The Anynet+ system supports Anynet+ devices only.
•• Check if the Anynet+ device power cord is properly connected.
•• Check the Anynet+ device’s Video/Audio/HDMI cable connections.
•• Check whether Anynet+ (HDMI-CEC) is set to On in the System menu.
•• Check whether the remote control is Anynet+ compatible.
•• Anynet+ doesn’t work in certain situations. (initial setup)
•• If you have removed and then reconnected the HDMI cable, please make sure to search devices again or turn your product off
and on again.
•• Check if the Anynet+ function of the Anynet device is set on.
I want to start Anynet+.
•• Check if the Anynet+ device is properly connected to the product and check if the Anynet+ (HDMI-CEC) is set to On in the
System menu.
I want to exit Anynet+.
•• Press the SOURCE button on the product remote control and select a non- Anynet+ device.
The message “Disconnecting
Anynet+ device ...” appears on
the screen.
•• You cannot use the remote control when you are configuring Anynet+ or switching to a view mode.
The Anynet+ device does not
play.
•• You cannot use the play function when initial setup is in progress.
The connected device is not
displayed.
•• Check whether or not the device supports Anynet+ functions.
•• Use the remote control after the product has completed Anynet+ configuration or has finished switching to Anynet+.
•• Check whether or not the HDMI cable is properly connected.
•• Check whether Anynet+ (HDMI-CEC) is set to On in the System menu.
•• Search Anynet+ devices again.
•• Anynet+ requires an HDMI connection. Make sure the device is connected to your product with an HDMI cable.
•• Some HDMI cables may not support Anynet+ functions.
•• If the connection is terminated because there has been a power failure or the HDMI cable has been disconnected, please repeat
the device scan.
105
HDMI Hot Plug
General
This feature is used to activate the time delay to turn on a DVI/HDMI source device.
Smart Security
•• Off / On
Anynet+ (HDMI-CEC)
On
HDMI Hot Plug
On
You can download, select, and set the display time of a custom logo that appears when the product turns on.
Custom Logo
Game Mode
Custom Logo
•• Custom Logo
Off
Empty Storage
――You can select a custom logo (image/video) or turn off the custom logo display.
――You must download the custom logo from an external USB device to set the custom logo.
•• Logo Display Time
――If the type of custom logo is Image, you can set the Logo Display Time.
•• Download Logo File
――The displayed image may differ depending on the model.
――You can download a custom logo into the product from an external USB device.
――The file name of the custom logo you want to download must be saved as “samsung” in all small letters.
――When there are multiple numbers of external USB connections, the product will attempt to download the custom logo from the
last device that has been connected to the product.
Custom logo file restrictions
•• For image type custom logo, only bitmap files (aRGB 32bpp format) are supported.
•• The resolution of the image type custom logo must be between a minimum of 128x64 and the maximum screen
resolution. (Horizontal/Vertical values of the resolution must be multiples of 4.)
•• For video type custom logo, only TS Stream types are supported.
•• The maximum supported video file is 150 MB. The recommended length of a video file is 20 seconds or less.
106
Game Mode
General
When connecting to a game console such as PlayStation™ or Xbox™, you can enjoy a more realistic gaming experience by
selecting game mode.
Smart Security
Anynet+ (HDMI-CEC)
On
HDMI Hot Plug
On
Custom Logo
Game Mode
Off
Empty Storage
•• Off / On
――Precautions and limitations for Game Mode
To disconnect the game console and connect another external device, set Game Mode to Off in the setup menu.
Empty Storage
Delete files to make space for new content. Recently played files will not be deleted.
――The displayed image may differ depending on the model.
Reset System
This option returns the current settings under system to the default factory settings.
MENU m → System → Reset System → ENTER E
System
Reset System
――The displayed image may differ depending on the model.
107
Chapter 10
Support
Software Update
Contact Samsung
MENU m → Support → Software Update → ENTER E
MENU m → Support → Contact Samsung → ENTER E
The Software Update menu lets you upgrade your product software to the latest version.
View this information when your product does not work properly or when you want to upgrade the
software.
――Be careful not to turn off the power until the upgrade is complete. The product will turn off and on
automatically after completing the software upgrade.
――When you upgrade software, all video and audio settings you have made will return to their default settings.
You can find information regarding our call centres and how to download products and software.
――Contact Samsung and find the product Model Code and Software Version.
We advise you to write down your settings so that you can easily reset them after the upgrade.
Update now
Reset All
Update the software to the latest version.
――Current version: This is the software version already installed in the product.
MENU m → Support → Reset All → ENTER E
This option returns all the current settings for a display to the default factory settings.
Auto update
This feature automatically updates the product when not in use.
•• Off / On
108
Chapter 11
Troubleshooting Guide
Requirements Before Contacting Samsung Customer Service Centre
–– Before calling Samsung Customer
Service Centre, test your product
as follows. If the problem persists,
contact Samsung Customer Service
Centre.
Testing the Product
Check if your product is operating normally by using the product test function.
If the screen remains blank while the power LED blinks even when the product is correctly connected to a PC, perform product testing.
–– If the screen remains blank, check the
PC system, video controller and cable.
1
Power off both the PC and product.
2
Disconnect all the cables from the product.
3
Power on the product.
4
If No Signal is displayed, the product is operating normally.
Checking the Resolution and Frequency
Not Optimum Mode will briefly be displayed if a mode that exceeds a supported resolution is selected (refer to Supported Resolutions).
109
Check the followings.
Installation issue (PC mode)
The screen keeps switching on and off.
Check the cable connection between the product and PC, and ensure the connection is secure.
Blank spaces are found on all four sides of the screen when an
HDMI or HDMI-DVI cable is connected to the product and PC.
The blank spaces found on the screen have nothing to do with the product.
Blank spaces on the screen are caused by the PC or graphics card. To resolve the problem, adjust the
screen size in the HDMI or DVI settings for the graphics card.
If the graphics card settings menu does not have an option to adjust the screen size, update the graphics
card driver to the latest version.
(Please contact the graphics card or computer manufacturer for further details about how to adjust the
screen settings.)
Screen issue
No Signal is displayed on the screen.
Check that the product is connected correctly with a cable.
Check that the device connected to the product is powered on.
Not Optimum Mode is displayed.
This message is displayed when a signal from the graphics card exceeds the product's maximum
resolution and frequency.
Refer to the Standard Signal Mode Table and set the maximum resolution and frequency according to the
product specifications.
The images on the screen look distorted.
Check the cable connection to the product.
The screen is not clear. The screen is blurry.
Set the resolution and frequency to the recommended level.
The screen appears unstable and shaky.
Check that the resolution and frequency of the PC and graphics card are set within a range compatible
with the product. Then, change the screen settings if required by referring to the Additional Information
on the product menu and the Standard Signal Mode Table.
There are shadows or ghost images left on the screen.
The screen is too bright. The screen is too dark.
Adjust Brightness and Contrast.
Screen colour is inconsistent.
Go to Picture and adjust the Colour Space settings.
White does not really look white.
Go to Picture and adjust the White Balance settings.
110
Screen issue
There is no image on the screen and the power LED blinks every The product is in power-saving mode.
0.5 to 1 second.
Press any key on the keyboard or move the mouse to return to the previous screen.
The product will turn off automatically.
Go to System and make sure Sleep Timer is set to Off.
If a PC is connected to the product, check the power status of the PC.
Make sure the power cable is connected properly to the product and power outlet.
If the signal from a connected device is not detected, the product automatically turns off after 10 to 15
minutes.
Picture quality of the product is different from the dealer shop
where it was purchased.
Use an HDMI cable to obtain high-definition (HD) picture quality.
The screen display does not look normal.
Encoded video content may cause the display to appear corrupted in scenes featuring fast moving objects
such as in a sports event or action video.
Low signal level or low picture quality may cause the display to appear corrupted. This does not mean the
product is defective.
A cell phone within a distance of one-meter radius may cause static on analogue and digital products.
The brightness and colour do not look normal.
Go to Picture and adjust the screen settings such as Picture Mode, Colour, Brightness and Sharpness.
Go to System and adjust the Energy Saving Mode settings.
Reset the screen settings to the default settings.
Lines (red, green or blue) are displayed on the screen.
These lines are displayed when there is a defect in DATA SOURCE DRIVER IC on the monitor. Contact a
Samsung Service Centre to resolve the issue.
The display looks unstable and then freezes.
The screen may freeze when a resolution other than the recommended resolution is used or if the signal
is not stable. To resolve the issue, change the PC resolution to the recommended resolution.
The screen cannot be displayed in full screen.
A scaled SD (4:3) content file can cause black bars on both sides of an HD channel screen.
A video with an aspect ratio different from the product can cause black bars at the top and bottom of the
screen.
Change the screen size setting to full screen on the product or source device.
111
Remote control issue
The remote control does not work.
Make sure that the batteries are correctly in place (+/-).
Check if the batteries are flat.
Check for power failure.
Make sure that the power cord is connected.
Check for any special lighting or neon signs switched on in the vicinity.
Source device issue
A beeping sound is heard when my PC is booting.
If a beeping sound is heard when your PC is booting, have your PC serviced.
Other issue
The product smells like plastic.
The plastic smell is normal and disappears over time.
Audio or video cuts out intermittently.
Check the cable connection and connect it again if required.
Using a very hard or thick cable may corrupt audio and video files.
Make sure cables are flexible enough to ensure durability. When mounting the product onto a wall, it is
recommended to use right-angle cables.
Small particles are found on the edges of the product.
The particles are part of the product design. The product is not defective.
When I try to change the PC resolution, a message The defined
resolution is not supported. appears.
The message The defined resolution is not supported. appears if the input source resolution exceeds the
maximum resolution of the display.
To resolve the issue, change the PC resolution to a resolution supported on the display.
HDMI Black Level is not functioning properly on an HDMI device This function is available only when a source device, such as a DVD player and STB, is connected to the
with YCbCr output.
product via an HDMI (RGB signal) cable.
112
Other issue
There is no sound in HDMI mode.
Displayed picture colours may not look normal. Video or sound may not be available. This can occur if a
source device that only supports an older version of the HDMI standard is connected to the product.
Some PC graphics cards may not automatically recognise HDMI signals that do not include sound. In this
case, manually select a sound input.
PC
The IR sensor is not functioning.
Sound input
Screen mode
Auto
PC settings
Make sure the sensor light turns on when a button is pressed on the remote control.
If the sensor light does not turn on, turn the power switch off and then on again on the back of the
product.
(The power LED lights up red when the screen is switched off.)
If the sensor light still does not turn on after the power switch is turned off and then on again, an internal
jack may be disconnected.
Contact your nearest service centre to have the product serviced.
If the sensor light that is on does not flash red when a button is pressed on the remote control, the IR
sensor may be defective.
Contact your nearest service centre to have the product serviced.
•• This function is available only when a source device, such as a DVD player and STB, is connected to
the product via an HDMI (RGB signal) cable.
113
Q&A
Question
How can I change the frequency?
Answer
Set the frequency on your graphics card.
•• Windows XP: Go to Control Panel → Appearance and Themes → Display → Settings → Advanced →
Monitor and adjust the frequency in Monitor Settings.
•• Windows ME/2000: Go to Control Panel → Display → Settings → Advanced → Monitor and adjust the
frequency in Monitor Settings.
–– Refer to the user manual for your PC or
•• Windows Vista: Go to Control Panel → Appearance and Personalization → Personalize → Display
Settings → Advanced Settings → Monitor and adjust the frequency in Monitor Settings.
graphics card for further instructions
on adjustment.
•• Windows 7: Go to Control Panel → Appearance and Personalization → Display → Adjust resolution →
Advanced Settings → Monitor and adjust the frequency in Monitor Settings.
•• Windows 8: Go to Settings → Control Panel → Appearance and Personalization → Display → Adjust
resolution → Advanced Settings → Monitor and adjust the frequency in Monitor Settings.
•• Windows 10: Go to Settings → System → Display → Advanced display settings → Display adapter
properties → Monitor, and adjust Screen refresh rate under Monitor settings.
How can I change the resolution?
•• Windows XP: Go to Control Panel → Appearance and Themes → Display → Settings and adjust the
resolution.
•• Windows ME/2000: Go to Control Panel → Display → Settings and adjust the resolution.
•• Windows Vista: Go to Control Panel → Appearance and Personalization → Personalize → Display
Settings and adjust the resolution.
•• Windows 7: Go to Control Panel → Appearance and Personalization → Display → Adjust Resolution
and adjust the resolution.
•• Windows 8: Go to Settings → Control Panel → Appearance and Personalization → Display → Adjust
Resolution and adjust the resolution.
•• Windows 10: Go to Settings → System → Display → Advanced display settings, and adjust the
resolution.
114
Question
How do I set powersaving mode?
Answer
•• Windows XP: Set power-saving mode in Control Panel → Appearance and Themes → Display → Screen
Saver Settings or BIOS SETUP on the PC.
•• Windows ME/2000: Set power-saving mode in Control Panel → Display → Screen Saver Settings or
BIOS SETUP on the PC.
•• Windows Vista: Set power-saving mode in Control Panel → Appearance and Personalization →
Personalize → Screen Saver Settings or BIOS SETUP on the PC.
•• Windows 7: Set power-saving mode in Control Panel → Appearance and Personalization →
Personalize → Screen Saver Settings or BIOS SETUP on the PC.
•• Windows 8: Set power-saving mode in Settings → Control Panel → Appearance and Personalization →
Personalize → Screen Saver Settings or BIOS SETUP on the PC.
•• Windows 10: Set power-saving mode in Settings → Personalization → Lock screen → Screen timeout
settings → Power & sleep or BIOS SETUP on the PC.
115
Chapter 12
Specifications
General
–– Size
Model Name
Panel
OH46F
OH55F
Size
46 CLASS (45.9 inches / 116 cm)
55 CLASS (54.6 inches / 138 cm)
Display area
1018.08 mm (H) x 572.67 mm (V) / 40.1 inches (H) x 22.5 inches (V)
1209.6 mm (H) x 680.4 mm (V) / 47.6 inches (H) x 26.8 inches (V)
Power Supply
AC100-240V~ 50/60Hz
Refer to the label at the back of the product as the standard voltage can vary in different countries.
–– Display area
H
Environmental
considerations
Operating
Temperature : -30 ℃ - 50 ℃ (-22 ℉ - 122 ℉)
* For installing the housing, keep the internal temperature at 40 °C or below.
Humidity : 10% - 80%, non-condensing
Storage
V
Temperature : -30 ℃ - 50 ℃ (-22 ℉ - 122 ℉)
Humidity : 5% - 95%, non-condensing
――Plug-and-Play
This monitor can be installed and used with any Plug-and-Play compatible systems. Two-way data exchange between the monitor and PC system optimises the monitor settings.
Monitor installation takes place automatically. However, you can customise the installation settings if desired.
――Due to the nature of the manufacturing of this product, approximately 1 pixel per million (1ppm) may appear brighter or darker on the panel. This does not affect product
performance.
――This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
――For detailed device specifications, visit the Samsung Electronics website.
116
Preset Timing Modes
――This product can be set to only one resolution for each screen size to obtain the optimum picture quality due to the nature of the panel. Using a resolution other than the specified
resolution may degrade the picture quality. To avoid this, it is recommended that you select the optimum resolution specified for your product.
――Check the frequency when you exchange a CDT product (connected to a PC) for an LCD product. If the LCD product does not support 85 Hz, change the vertical frequency to 60 Hz
using the CDT product before you exchange it with the LCD product.
–– Horizontal Frequency
The time required to scan a single line
from the left to the right side of the
Model Name
Synchronization
screen is called a horizontal cycle.
The reciprocal number of a horizontal
cycle is called horizontal frequency.
Horizontal frequency is measured in
Resolution
OH46F / OH55F
Horizontal Frequency
30 – 81 kHz
Vertical Frequency
48 – 75 Hz
Optimum Resolution
1920 x 1080 @ 60 Hz
Maximum Resolution
1920 x 1080 @ 60 Hz
kHz.
–– Vertical Frequency
The product displays a single image
multiple times per second (like a
fluorescent light) to display what
the viewer sees. The rate of a single
image being displayed repeatedly per
second is called vertical frequency
or refresh rate. Vertical frequency is
measured in Hz.
The screen will automatically be adjusted if a signal that belongs to the following standard signal modes is transmitted from your PC. If the signal transmitted from the
PC does not belong to the standard signal modes, the screen may be blank with the power LED on. In such a case, change the settings according to the following table by
referring to the graphics card user manual.
Resolution
Horizontal Frequency
Vertical Frequency
Pixel Clock
Sync Polarity
(kHz)
(Hz)
(MHz)
(H/V)
IBM, 720 x 400
31.469
70.087
28.322
-/+
MAC, 640 x 480
35.000
66.667
30.240
-/-
MAC, 832 x 624
49.726
74.551
57.284
-/-
MAC, 1152 x 870
68.681
75.062
100.000
-/-
VESA, 640 x 480
31.469
59.940
25.175
-/-
VESA, 640 x 480
37.861
72.809
31.500
-/-
VESA, 640 x 480
37.500
75.000
31.500
-/-
VESA, 800 x 600
37.879
60.317
40.000
+/+
117
Resolution
Horizontal Frequency
Vertical Frequency
Pixel Clock
Sync Polarity
(kHz)
(Hz)
(MHz)
(H/V)
VESA, 800 x 600
48.077
72.188
50.000
+/+
VESA, 800 x 600
46.875
75.000
49.500
+/+
VESA, 1024 x 768
48.363
60.004
65.000
-/-
VESA, 1024 x 768
56.476
70.069
75.000
-/-
VESA, 1024 x 768
60.023
75.029
78.750
+/+
VESA, 1152 x 864
67.500
75.000
108.000
+/+
VESA, 1280 x 720
45.000
60.000
74.250
+/+
VESA, 1280 x 800
49.702
59.810
83.500
-/+
VESA, 1280 x 1024
63.981
60.020
108.000
+/+
VESA, 1280 x 1024
79.976
75.025
135.000
+/+
VESA, 1366 x 768
47.712
59.790
85.500
+/+
VESA, 1440 x 900
55.935
59.887
106.500
-/+
VESA(RB), 1600 x 900
60.000
60.000
108.000
+/+
VESA, 1680 x 1050
65.290
59.954
146.250
-/+
VESA, 1920 x 1080
67.500
60.000
148.500
+/+
118
Chapter 13
Appendix
Responsibility for the Pay Service (Cost to
Customers)
A Product damage caused by customer's fault
――When the service is requested, in spite of in warranty, we may charge you for a visit from a service technician
•• External impact or drop.
in the following cases.
Not a product defect
Cleaning of the product, Adjustment, Explanation, Re-installation and etc.
•• If a service technician gives instructions on how to use product or simply adjusts options without
disassembling product.
Product damage caused by customer's mishandling or wrong repair
If a product damage is caused by;
•• Use of supplies or separatly sold product unspecified by Samsung.
•• Repair from a person besides an engineer of outsourcing service company or partner of Samsung
Electronics Co., Ltd.
•• Remodeling or repairing the product by customer.
•• Using it with incorrect voltage or non-authorised electrical connections.
•• Not following the "cautions" in User Manual.
•• If a defect is caused by external environmental factors (Internet, Antenna, Wired Signal, etc.)
•• If a product is reinstalled or devices are connected additionally after installing the purchased product
for the first time.
•• If a product is reinstalled to move to a different spot or to move to a different house.
•• If customer requests instructions on how to use because of another company's product.
•• If customer requests instructions on how to use the network or another company's programme.
•• If customer requests software installation and setup for the product.
Others
•• If product fails by natural disaster. (lightning, fire, earthquake, flood damage, etc)
•• If consumable components are all used up. (Battery, Toner, Fluorescent lights, Head, Vibrator, Lamp,
Filter, Ribbon, etc.)
――If customer requests a service in case the product has no defect, service fee may be charged. So please read
User Manual first.
•• If a service technician removes/cleans dusts or foreign materials inside of the product.
•• If customer requests an installation additionally after purchasing a product through home-shopping
or online.
119
Optimum Picture Quality and Afterimage
Burn-in Prevention
Black Matrix
Common
Electrode (ITO)
Colour-Filter
Optimum Picture Quality
•• Due to the nature of the manufacturing of this product, approximately 1 pixel per million (1ppm) may
be brighter or darker on the panel. This does not affect product performance.
Source
Drain
‒‒ The number of sub-pixels by panel type: 6,220,800
•• Leaving the screen fixed on a stationary image for an extended period of time may cause afterimage
burn-in or defective pixels.
‒‒ Activate power-saving mode or a dynamic screen saver if you will not be using the product for an
extended period of time.
Gate
Prevention of Afterimage Burn-in
TFT
Pixel Electrode (ITO)
Storage
Capaccitor (Cs)
Data Bus-Line
What is afterimage burn-in?
Afterimage burn-in should not occur when the LCD panel is operating normally. Normal operation refers
to a continuously changing video pattern. If the LCD panel displays a fixed pattern for an extended period
of time, a slight voltage difference may occur between the electrodes in pixels that control the liquid
crystals.
Such a voltage difference between electrodes increases with time and makes the liquid crystals thinner.
When this occurs, a previous image can remain on the screen when the pattern changes. To prevent this,
the accumulated voltage difference should be reduced.
――Afterimage burn-in should not occur when an LCD panel is operating in proper conditions.
120
Preventing afterimage burn-in
•• Regular Text colour Change
――The best way to protect the product from afterimage burn-in is switching the power off or setting the PC or
system to run a screen saver when not in use. Also, Warranty service may be limited depending on instruction
guide.
‒‒ Use bright colours of similar brightness.
Interval: Change text colour and background colour every 30 minutes
FLIGHT : TIME
•• Powering Off, Screen Saver and Power Saving Mode
‒‒ Power off the product for 2 hours after using it for 12 hours.
‒‒ Go to Display Properties > Power Supply on your PC and set the product to power off as required.
OZ348
: 20:30
FLIGHT : TIME
: 20:30
OZ348
‒‒ Using a screen saver is recommended.
FLIGHT : TIME
It is best to use a single-colour or moving-image screen saver.
•• Regular colour Change
OZ348
‒‒ Use 2 colours
: 20:30
FLIGHT : TIME
: 20:30
OZ348
Switch between 2 colours every 30 minutes as shown above.
Type 1
‒‒ Move and change text every 30 minutes as shown below.
Type 2
FLIGHT
TIME
FLIGHT
TIME
OZ348
20:30
OZ348
20:30
UA102
21:10
UA102
21:10
FLIGHT
: TIME
OZ348
: 20:30
[ Step 1 ]
[ Step 2 ]
•• Avoid combinations of a text colour and background colour of contrasting brightness.
(Brightness: refers to the lightness or darkness of a colour which varies depending on the amount of
light emitted.)
――Avoid using grey as it may contribute to afterimage burn-in.
――Avoid using colours of contrasting brightness (black and white; grey).
FLIGHT : TIME
FLIGHT : TIME
OZ348 : 20:30
OZ348 : 20:30
FLIGHT
: TIME
OZ348
: 20:30
[ Step 3 ]
‒‒ Regularly display a moving image along with a logo.
Interval: Display a moving image along with a logo for 60 seconds after using for 4 hours.
121
Licence
Manufactured under license from Dolby Laboratories.
Dolby, Dolby Audio, Pro Logic, and the double-D symbol are
trademarks of Dolby Laboratories.
For DTS patents, see http://patents.dts.com. Manufactured under license from
DTS, Inc. DTS, the Symbol, DTS in combination with the Symbol, DTS Premium
Sound|5.1, DTS Digital Surround, DTS Express, and DTS Neo2:5 are registered
trademarks or trademarks of DTS, Inc. in the United States and/ or other
countries. © DTS, Inc. All Rights Reserved.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI
Logo are trademarks or registered trademarks of HDMI Licensing LLC in the
United States and other countries.
DivX Certified® to play DivX® video up to HD 1080p, including premium
content.
DivX®, DivX Certified® and associated logos are trademarks of DivX, LLC and
are used under license.
This DivX Certified® device has passed rigorous testing to ensure it plays DivX® video.
To play purchased DivX movies, first register your device at vod.divx.com. Find your registration
code in the DivX VOD section of your device setup menu.
Covered by one or more of the following U.S. patents: 7,295,673; 7,460,668; 7,515,710; 8,656,183;
8,731,369; RE45,052.
This device supports DivX Plus Streaming® for enjoying HD movies and TV shows with advanced
features (multi-language subtitles, multiple audio tracks, chapters, smooth FF/RW, etc.)
streamed to your device.
Open Source Licence Notice
In the case of using open source software, Open Source Licences are available on the product menu.
Open Source Licence Notice is written only English.
For information on the Open Source Licence Notice, contact the Samsung Customer Centre or send
email to oss.request@samsung.com.
122
Terminology
480i / 480p / 720p / 1080i /
1080p____ Each of the scanning
rates above refers to the number of
effective scanning lines that decides
the screen resolution. The scanning
rate may be indicated in i (interlaced)
or p (progressive), depending on the
scanning method.
- Scanning
Scanning refers to a process of
sending pixels that form an image
progressively. A larger number of
pixels will deliver a clearer and more
vivid picture.
- Progressive
In progressive scan mode, all lines
of pixels are scanned one by one
(progressively) on the screen.
- Interlaced
In interlaced scan mode, every other
line of pixels is scanned from top to
bottom first and then the remaining
lines of pixels (that were not scanned)
are scanned.
Non-interlace Mode and Interlace
Mode____ Non-interlace mode
(progressive scan) displays a
horizontal line from the top to the
bottom of a screen progressively.
Interlace mode displays the odd
number lines first and the even
number lines next. Non-interlace
mode is mainly used in monitors as it
produces screen clarity and interlace
mode is mainly used in TVs.
Dot Pitch____ The screen consist of
red, green and blue dots. A shorter
distance between the dots produces
a higher resolution. Dot pitch refers
to the distance between the shortest
distance between dots of the same
colour. Dot pitch is measured in
millimetres.
Vertical Frequency____ The product
displays a single image many times
per second (like a fluorescent light
that flickers) to display an image for
a viewer to see. The rate of a single
image being displayed repeatedly per
second is called vertical frequency
or refresh rate. Vertical frequency is
measured in Hz.
E.g. 60Hz refers to a single image
being displayed 60 times in one
second.
Horizontal Frequency____ The
time required to scan a single line
from the left to the right side of the
screen is called a horizontal cycle.
The reciprocal number of a horizontal
cycle is called horizontal frequency.
Horizontal frequency is measured in
kHz.
Source____ Input source refers to a
video source device connected to the
product such as a camcorder or video
or DVD player.
Plug & Play____ Plug & Play is a
function that allows the automatic
exchange of information between
a monitor and PC to produce an
optimum display environment. The
product uses VESA DDC (international
standard) to execute Plug & Play.
Resolution____ Resolution is the
number of horizontal dots (pixels)
and vertical dots (pixels) that form
a screen. It represents the level of
display detail. A higher resolution
enables more data to be displayed on
the screen and is useful to perform
multiple tasks simultaneously.
E.g. A resolution of 1920 X 1080
consists of 1,920 horizontal pixels
(horizontal resolution) and 1,080
vertical pixels (vertical resolution).
DVD (Digital Versatile Disc)____ DVD
refers to a CD-sized mass storage
disk where you can save multimedia
(audio, video or game) applications
using MPEG-2 video compression
technology.
HDMI (High Definition Multimedia
Interface)____ It is an interface that
can be connected to a digital audio
source as well as a high-definition
video source by using a single cable
without compression.
Multiple Display Control (MDC)____
MDC (Multiple Display Control) is
an application that allows multiple
display devices to be controlled
simultaneously using a PC.
Communication between a PC and
monitor takes place using RS232C
(serial data transmission) and RJ45
(LAN) cables.
123
Download PDF