Samsung | QM65N | Samsung QM65N Benutzerhandbuch

User Manual
QBN (QB43N QB49N QB55N QB65N QB75N)
QMN (QM43N QM49N QM55N QM65N QM75N)
The colour and the appearance may differ depending on the product, and the content in the
manual is subject to change without prior notice to improve the performance.
Recommended hours of use per day for the QBN models is less than 16 hours.
If the product is used for longer than 16 hours a day, the warranty may be void.
An administration fee may be charged in the following situations:
(a) An engineer is called out at your request, but it is found that the product has no defect (i.e.,
where the user manual has not been read).
(b) You bring the unit to a repair centre, but it is found that the product has no defect (i.e.,
where the user manual has not been read).
You will be informed of the administration fee amount before a technician visits.
© Samsung Electronics
Samsung Electronics owns the copyright for this manual. Use or reproduction of this manual in parts or entirety without the authorization of Samsung Electronics is prohibited. Trademarks other than Samsung Electronics are
property of their respective owners.
Table of contents
Before Using the Product
Safety Precautions
6
Safety symbols
6
Electricity and Safety
7
Installation8
Operation10
Cleaning12
Storage and Maintenance
13
Preparations
Checking the Components
14
Parts15
Ports17
Remote Control
18
Before Installing the Product (Installation
Guide)20
Tilting Angle and Rotation
20
Ventilation20
Installing the Wall Mount
Preparing before installing Wall-Mount
Installing the Wall Mount
Wall Mount Kit Specifications (VESA)
21
21
21
22
Connecting and Using
a Source Device
Before Connecting
Pre-connection Checkpoints
Multiple Display Control
23
23
Connecting to a PC
23
Connection Using an HDMI Cable
23
Connection Using an DP Cable
24
Connection using a DVI cable (Digital type) 24
Connection Using an HDMI-DVI Cable
25
Connecting an External Monitor
26
Connecting to a Video Device
Connection Using an HDMI-DVI Cable
Connection Using an HDMI Cable
27
27
28
Connecting to an Audio System
28
Connecting the LAN Cable
28
Changing the Input source
29
Source29
Web Browser30
Remote Workspace31
Cable Connection
32
RS232C Cable
32
LAN Cable
33
Connection35
36
Control Codes
Using MDC
43
MDC Programme Installation/Uninstallation 43
Player feature
Player44
Viewing content
44
When content is running
45
45
Available menu
File Formats Compatible with Player46
Schedule51
Clone Product52
ID Settings53
Device ID53
Device ID Auto Set53
PC Connection Cable53
Video Wall54
Video Wall54
Horizontal x Vertical54
Screen Position55
Format55
2
Table of contents
Network Status56
On/Off Timer57
On Timer57
Off Timer58
Holiday Management58
Ticker59
URL Launcher60
URL Launcher Settings61
Screen Adjustment
Picture Options67
Colour Tone67
Digital Clean View67
HDMI Black Level67
Film Mode67
Dynamic Backlight67
Apply Picture Settings68
Picture Size Settings69
Picture Size69
Fit to screen69
Zoom and Position69
Reset Picture70
Backlight / Brightness / Contrast / Sharpness62
Reset OnScreen Display76
Sound Adjustment
Sound Mode77
Balance78
Equaliser78
HDMI Sound78
Sound on Video Call78
Sound Output79
Auto Volume79
Colour Temperature63
OnScreen Display
Advanced Settings64
Picture Enhancer64
HDR+ Mode64
Colour64
Tint (G/R)64
White Balance65
Gamma65
Contrast Enhancer65
Black Tone65
Flesh Tone66
RGB Only Mode66
Colour Space Settings66
HDMI UHD Color66
Motion Lighting66
Display Orientation71
Onscreen Menu Orientation71
Source Content Orientation71
Aspect Ratio71
Screen Protection72
Auto Protection Time72
Screen Burn Protection72
Message Display75
Source Info75
No Signal Message75
MDC Message75
Download Status Message75
Reset Sound79
Network
Network Status80
Open Network Settings80
Network Type80
Network Settings (Wired)
81
Network Settings (Wireless)
83
Use WPS85
IPv685
IPv6 Status85
Language76
3
Table of contents
Server Network Settings86
Connect to server86
MagicInfo Mode86
Server Access86
FTP Mode86
Proxy server86
Auto Power On91
PC module power91
Max. Power Saving91
Standby Control92
Network Standby92
Power Button92
Device Name86
Eco Solution93
Energy Saving Mode93
Screen Lamp Schedule93
No Signal Power Off94
Auto Power Off94
Software Update104
Update Now104
Temperature Control94
Contact Samsung104
External Device Manager95
Input Device Manager95
Device Connection Manager96
Terms & Conditions104
System
Accessibility87
High Contrast87
Enlarge87
Start Setup88
Touch Control88
Touch Control88
Admin Menu Lock88
Time89
Clock Set89
NTP Settings89
DST89
Power On Delay89
Auto Source Switching90
Auto Source Switching90
Primary Source Recovery90
Primary Source90
Secondary Source90
Power Control91
Custom Logo102
Game Mode103
Empty Storage103
Reset System103
Support
Reset All104
Play via97
Change PIN97
Troubleshooting Guide
Security98
Safety Lock On98
Button Lock98
USB Auto Play Lock98
Mobile Connection Lock99
Remote Management99
Network Port99
USB Port99
Requirements Before Contacting Samsung
Customer Service Centre
Testing the Product
Checking the Resolution and Frequency
Check the followings.
105
105
105
106
Q & A
112
General100
Smart Security100
Anynet+ (HDMI-CEC)100
HDMI Hot Plug102
4
Table of contents
Specifications
General113
Preset Timing Modes
115
Appendix
Responsibility for the Pay Service (Cost to
Customers)117
Not a product defect
117
A Product damage caused by customer's
fault117
Others117
Prevention of Afterimage Burn-in
What is afterimage burn-in?
Recommended prevention practices
118
118
118
Licence119
5
Chapter 01
Before Using the Product
Safety Precautions
The following safety instructions are to ensure your personal safety and prevent property
damage. Please read the following to ensure the proper use of the product.
RISK OF ELECTRIC SHOCK. DO NOT OPEN.
Safety symbols
Symbol
Name
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). THERE
ARE NO USER SERVICEABLE PARTS INSIDE. REFER ALL SERVICING TO QUALIFIED PERSONNEL.
Meaning
Warning
A serious or fatal injury may result if instructions are not followed.
Caution
Personal injury or damage to properties may result if instructions
are not followed.
Prohibition Do NOT attempt.
Instruction Follow directions.
CAUTION
This symbol indicates that high
voltage is present inside. It is
dangerous to make any kind of
contact with any internal part of this
product.
AC voltage: Rated voltage marked
with this symbol is AC voltage.
This symbol indicates that this
product has included important
literature concerning operation and
maintenance.
DC voltage: Rated voltage marked
with this symbol is DC voltage.
Class II product: This symbol
indicates that a safety connection
to electrical earth (ground) is not
required.
Caution. Consult instructions for use:
This symbol instructs the user to
consult the user manual for further
safety related information.
6
Electricity and Safety
Insert the power plug all the way in so it is not loose.
"" The following images are for reference only. Real-life situations may differ from what is
shown in the images.
Clean any dust around the pins of the power plug or the power socket with a dry cloth.
An unsecure connection may cause a fire.
A fire may result.
Warning
Connect the power plug to a grounded power socket. (Except for devices that do not
provide grounding)
Do not touch the power plug with wet hands.
Otherwise, an electric shock may result.
An electric shock or injury may result.
Do not use a damaged power plug or a loose power socket.
An electric shock or fire may result.
Do not bend or pull the power cable with force. Be careful not to
leave the power cable under a heavy object.
Product failure, an electric shock or fire may result from a damaged
cable.
Do not connect multiple products to a single power socket.
Overheated power sockets may cause a fire.
7
Installation
Caution
Hold the plug when disconnecting the power cable from the power
socket.
An electric shock or fire may result.
Warning
Before moving the product, turn off the power switch and disconnect
the power cable and all other connected cables.
Damage to the cable may cause a fire or electric shock.
When connecting the power plug to the port, be sure to connect it
completely.
If the power plug is not completely connected to the port, the plug
may be unexpectedly disconnected, or there is a risk of overheating
due to overcurrent, leading to safety accidents.
When installing the product, keep it at a distance from the wall so
that it is well ventilated.
An increased internal temperature may cause a fire.
Only use the power cable provided with your product by Samsung. Do not use the
power cable with other products.
An electric shock or fire may result.
Do not install the product in a poorly ventilated space such as
bookcase or closet.
Keep the power socket where the power cord is connected unobstructed.
An increased internal temperature may cause a fire.
When a problem occurs with the product, the power cord must be unplugged to
completely cut off power to the product. The power is not completely cut off by using
only the Power button on the body of the product.
Do not disconnect the power cable while the product is being used.
Keep the plastic packaging out of the reach of children.
The product may become damaged by an electric shock.
Children's misuse of the plastic packaging may cause suffocation.
Do not install the power cable (DC power supply) and the product
near head sources.
(Candles, mosquito repellents, cigarettes, sprays, heating devices,
places exposed to direct sunlight, and more)
8
When installing the product, fix it firmly so that it does not fall.
If the product is not fixed firmly and a child touches the product while
playing, the product may fall, causing damage to the product or injury
to the child.
Caution
When lifting and moving the product, do not touch the screen
display, and make sure that at least two people work together.
The product may fall, causing personal injury or product damage.
Do not install the product in a kitchen or near a kitchen counter.
Edible oil or oil vapor can damage or deform the product.
Do not lay down the product on its front.
The screen may become damaged.
Prolonged exposure to direct sunlight may discolour the surface of the screen display.
Have a technician install the wall-mount hanger.
Installation by an unqualified person can result in an injury. Only use approved
cabinets.
If the product is installed in an unusual location, the surrounding environment may
cause a serious quality problem. Therefore, be sure to contact Samsung Customer
Service Centre before installation.
(Places where many fine dusts are generated, places where chemicals are used,
places with too high or low temperatures, places with a lot of moisture or water,
transportation equipment such as vehicles, airports and stations used continuously
for a long time, and more)
9
Operation
Do not apply an impact to the product.
•• The screen display may be damaged.
•• An electric shock or fire may result.
Warning
If the product generates a strange noise, a burning smell, or smoke,
unplug the power plug immediately and contact your Samsung
Customer Service Centre.
An electric shock or fire may result.
Keep the remote control batteries and the small accessories out of
the reach of children. Ensure children do not swallow any of them.
If children have had the battery in their mouths, consult your doctor
immediately.
If the product is dropped or its appearance is damaged, turn off the
power switch and disconnect the power cord. Then contact Samsung
Customer Service Centre.
Continued use can result in an electric shock or a fire.
Do not insert metallic objects (chopsticks, coins, hairpins, etc) or
objects that burn easily (paper, matches, etc) into the product (via
the vent or input/output ports, etc).
•• If foreign substances enter the product, be sure to power off the
product and disconnect the power cord. Then contact Samsung
Customer Service Centre.
•• Product failure, an electric shock or fire may result.
Do not place objects containing liquid (vases, pots, bottles, etc) or
metallic objects on top of the product.
•• If foreign substances such as water enter the product, be sure
to disconnect the power cord. Then contact Samsung Customer
Service Centre.
•• Product failure, an electric shock or fire may result.
During a lightning or thunderstorm, power off the product and
disconnect the power cord.
An electric shock or fire may result.
Do not move the product by pulling the power cord or any cable.
Product failure, an electric shock or fire may result from a damaged
cable.
Do not leave heavy objects or items that children like (toys, sweets,
etc.) on top of the product.
The product or heavy objects may fall as children try to reach for the
toys or sweets resulting in a serious injury.
Ensure the vents are not blocked by tablecloths or curtains.
An increased internal temperature may cause a fire.
10
Do not hang on or climb on the product.
•• The product may fall, causing personal injury or even death.
•• Be especially careful that children do not hang on or climb on the
product.
While the power plug is plugged into a power socket, do not insert
a chopstick or other conductor into a remaining power socket. Also,
after disconnecting the power plug from the power socket, do not
touch the pins of the plug immediately.
Otherwise, an electric shock may result.
Caution
Insert each battery so that its polarity (+, –) is correct.
If the polarity is not correct, the battery may rupture or the
internal fluid may leak, causing contamination and damage to the
surroundings, fire, or personal injury.
Do not place heavy objects on the product.
Product failure or personal injury may result.
There is a high voltage inside the product. Never disassemble, repair
or modify the product yourself.
•• Contact Samsung Customer Service Centre for repairs.
•• An electric shock or fire may result.
If a gas leakage is found, do not touch the product or the power plug, and ventilate the
room immediately.
Sparks can cause an explosion or fire.
Do not use humidifiers or stoves around the product.
An electric shock or fire may result.
When you do not use the product for a long time due to vacation or other reason,
disconnect the power cord from the power socket.
Dust accumulation combined with heat can cause a fire, electric shock or electric
leakage.
Use the product at the recommended resolution and frequency.
Your eyesight may deteriorate.
The batteries (and rechargeable batteries) are not ordinary refuse and must be
returned for recycling purposes. The customer is responsible for returning the used or
rechargeable batteries for recycling.
The customer can return used or rechargeable batteries to a nearby public recycling
centre or to a store selling the same type of the battery or rechargeable battery.
Rest your eyes for more than 5 minutes for every 1 hour of product use.
Eye fatigue will be relieved.
Leaving the screen fixed on a stationary image for an extended period of time may
cause afterimage burn-in or defective pixels.
When you do not use the product for a long time, activate power-saving mode or set
the screen saver to moving-picture mode.
Do not use or keep combustible spray or an inflammable substance near the product.
An explosion or fire may result.
11
Use only the specified standardised batteries, and do not use a new battery and a used
battery at the same time.
Otherwise, the batteries may be damaged or cause fire, personal injury or damage due
to a leakage of the internal liquid.
Cleaning
Warning
Do not watch the product screen too closely and continuously for a long time.
Do not spray water or cleaner directly on the product.
Your eyesight may deteriorate.
•• The product’s surface may be damaged, or the markings may be
erased.
Do not lift or move the product when it is in operation.
•• An electric shock or fire may result.
Do not touch the screen when the product has been turned on for an extended period
of time as it will become hot.
When using headphones or earphones, do not turn the volume too high or use them
for a long time.
Damage to your hearing may result.
Caution
When cleaning, be sure to disconnect the power plug and wipe gently with a soft and
dry cloth such as superfine fibers or cotton flannels to prevent scratches.
The product's surface may be damaged, or the markings may be erased.
Be sure to use a soft and dry cloth such as superfine fibers or cotton flannels because
the surface of the product and the screen display are vulnerable to scratches.
The product's surface or the screen display can be easily scratched with foreign
substances.
Do not apply chemicals containing alcohol, solvent, or surfactant such as wax,
benzene, thinner, pesticide, aerial freshener, lubricant, or cleaner to the product.
The product's exterior may be discoloured or cracked, the surface of the panel may be
peeled off, or the markings may be erased.
12
Storage and Maintenance
Cleaning the exterior and display
Wipe the surface with a slightly wet, soft cloth, and then wipe with a dry cloth.
1
2
3
Precautions
Do not scratch the screen
with nails or sharp objects.
Scratches may leave marks or
damage the product.
Do not spray water directly
on any part of the product.
Product failure, an electric
shock or fire may result from
water that enters the product.
Due to the characteristics of
high-glossy products, using
a UV humidifier nearby may
create white-coloured stains
on the product.
•• Removing a sticker attached on the screen may leave residues. Clean the residues before
watching the screen.
•• Do not strongly press and rub the product. Damage to the product may result.
•• Do not wipe the screen with chemicals. Product failure may result.
•• Contact Customer Service Centre if the inside of the product needs cleaning (service fee
will be charged).
13
Chapter 02
Preparations
Checking the Components
"" Contact the vendor where you
purchased the product if any
components are missing.
"" The appearance of the components
may differ from the images shown.
Quick Setup Guide
Warranty card
(Not available in some locations)
Regulatory guide
Power cord
"" A stand is not provided with the
product. To install a stand, you can
purchase one separately.
"" The RS232C adapter can be used to
connect to another monitor using the
D-SUB (9-pin) type RS232C cable.
Batteries (AAA x 2)
(Not available in some locations)
HOLDER-CABLE
Remote Control
RS232C(IN) adapter
(Supported models: QB65N,
QB75N, QM65N, QM75N)
Holder-Ring x 4
14
Parts
"" The colour and shape of parts may differ from what is shown. Specifications are subject to change without
notice to improve quality.
Remote sensor
Parts
Remote sensor
Power button
Description
Press a button on the remote control pointing at the sensor on the front of the product
to perform the corresponding function.
"" Using other display devices in the same space as the remote control of this product
can cause the other display devices to be inadvertently controlled.
Turns the product on or off.
Use the remote control within 2.5 m to 4 m from the sensor on the product at an angle of 30° from the left and
right.
Power indicator
Power button
"" Store used batteries out of reach of children and recycle.
"" Do not use a new and used battery together. Replace both batteries at the same time.
"" Remove batteries when the remote control is not to be used for an extended period of time.
"" To enhance the IR receiver performance, connect an External IR Sensor (sold separately) to the IR IN port.
Speaker
15
"" The power button is located in the lower centre of the product.
"" If you press the P button on the power button when the product is
turned on, the control menu will be displayed.
Buttons
Power off the product.
Power off
Control menu
Description
•• With the control menu screen displayed, briefly press the power button to
move the cursor to Power off , and then press and hold the power button to
turn off the product.
Select the connected input source.
Source
•• With the control menu screen displayed, briefly press the power button to
move the cursor to Source , and then press and hold the power button to
display the input source screen.
•• With the input source screen displayed, press and hold the power button to
switch to the desired input source.
Power off
Source
"" The power button can only be used for Power off and Source.
"" To exit from the control menu screen, wait for 3 seconds or more without pressing the power button.
Press: Move
Press & Hold: Select
16
Ports
Port
Description
Connect to a USB memory device.
"" The colour and shape of parts may differ from what is shown.
Specifications are subject to change without notice to improve quality.
QBN
QMN
USB 1 ¨(1.0A)
"" The USB ports on the product accept a maximum constant current of 1.0A.
If the maximum value is exceeded, USB ports may not work.
Connects to MDC using a LAN cable. (10/100 Mbps)
RJ45
"" Use Cat7(*STP Type) cable for the connection.
*Shielded Twist Pair.
RS232C IN
Connects to MDC using an RS232C adapter.
DVI/MAGICINFO IN
DVI: Connects to a source device using a DVI cable or HDMI-DVI cable.
MAGICINFO IN: To use MagicInfo, make sure to connect the DP-DVI cable.
HDMI IN 1 (ARC)
HDMI IN 2
Connects to a source device using a HDMI cable or HDMI-DVI cable.
HDMI IN 2 (DAISY CHAIN IN)
•• Connects to a source device using a HDMI cable or HDMI-DVI cable.
•• Connects to another product using a HDMI cable.
DP IN (DAISY CHAIN IN)
Connects to a PC using a DP cable.
HDMI OUT (DAISY CHAIN OUT)
Connects to another product using a HDMI cable.
Connect to a USB memory device.
USB 2(0.5A)
"" The USB ports on the product accept a maximum constant current of
0.5A. If the maximum value is exceeded, USB ports may not work.
DVI/HDMI AUDIO IN
Receives sound from a source device via an audio cable.
AUDIO OUT
Outputs sound to an audio device via an audio cable.
IR IN
Connects to an external IR cable that receives signals from the remote control.
RS232C OUT
Connects to MDC using an RS232C adapter.
17
Remote Control
"" Using other display devices in the same space as the remote control of this product can cause the other display devices to be inadvertently controlled.
"" A button without a description in the image below is not supported on the product.
Power on the product.
POWER
OFF
.QZ
ABC
DEF
GHI
JKL
MNO
PRS
TUV
WXY
DEL-/--
SYMBOL
1
4
7
Adjust the volume.
Change the input source.
2
5
8
0
3
6
SOURCE
Number buttons
Enter the password in the OSD menu.
9
"" Remote control button functions
may differ for different products.
CH LIST
Mute the sound.
MUTE
VOL
Power off the product.
CH
•• Unmuting the sound: Press MUTE again
or press the volume control(+ VOL -)
button.
Use this hotkey to directly access MagicInfo.
Display or hide the onscreen display menu, or
return to the previous menu.
MENU
HOME
MagicInfo
Player I
"" This hotkey is available when a network
box is connected.
A shortcut button to Home screen (MagicInfo
or URL Launcher).
18
Quickly select frequently used functions by
pressing it while a USB content is playing.
TOOLS
INFO
Display information about the current input
source.
Move to the upper, lower, left or right menu,
or adjust an option's setting.
Confirm a menu selection.
Return to the previous menu.
It sets safe lock function.
If multiple products are connected through the
Video Wall feature, press the SET button and
enter a device ID using numeric buttons.
RETURN
EXIT
PC
DVI
HDMI
DP
A
B
C
D
IR control
SET
UNSET
LOCK
Exit the current menu.
Select from the connected external devices.
"" Some models may not support all port
types.
Control the product using the remote control.
Cancel a value that has been set using the SET
button and control all connected products using
the remote control.
"" Remote control button functions
may differ for different products.
"" Remove batteries when the remote
control is not to be used for an
extended period of time.
To place batteries in the remote control (AAA x 2)
19
Before Installing the Product (Installation
Guide)
Ventilation
"" Contact Samsung Customer Service Centre for further details.
Installation on a Perpendicular Wall
To prevent injury, this apparatus must be securely attached to the floor/wall in accordance
with the installation instructions.
A Minimum 40 mm
•• Ensure that an authorised installation company installs the wall mount.
B Ambient temperature: Under 35 °C
•• Otherwise, it may fall and cause personal injury.
"" When installing the product on a perpendicular wall, allow at least
40 mm of space between the product and wall surface for ventilation
and ensure that the ambient A temperature is kept below 35 °C.
•• Make sure to install the specified wall mount.
A
Tilting Angle and Rotation
"" Contact Samsung Customer Service Centre for further details.
•• The product can be tilted at a maximum angle of 15° from a perpendicular wall surface.
B
•• To use the product vertically (portrait), turn it clockwise so that the LED is pointing down.
15°
Installation on an Indented Wall
A Minimum 40 mm
B Minimum 70 mm
B
C Minimum 50 mm
D Minimum 50 mm
E Ambient temperature: Under 35 °C
A
"" When installing the product on an indented wall, allow at least the
space specified above between the product and wall for ventilation
and ensure that the ambient temperature is kept below 35 °C.
C
E
D
D
20
Installing the Wall Mount
Preparing before installing Wall-Mount
To install a wall-mount from another manufacturer, use the Holder-Ring.
Installing the Wall Mount
•• The wall mount kit (sold separately) allows you to mount the product on the wall.
•• The provided image is only for reference. For detailed information on installing the wall mount, see instructions
provided with the wall mount.
•• We recommend you contact a technician for assistance when installing the wall mount bracket.
•• Samsung Electronics is not responsible for any damage to the product or injury to yourself or others if you select
to install the wall mount on your own.
21
Wall Mount Kit Specifications (VESA)
•• Samsung wall mount kits contain a detailed installation manual and all parts necessary for assembly are
provided.
"" Install your wall mount on a solid wall perpendicular to the floor. To
install the product on the other wall area, contact the nearest agency.
If you install the product on a slanted wall, it may fall and result in
severe personal injury.
•• Do not use screws that are longer than the standard length or do not comply with the VESA standard screw
specifications. Screws that are too long may cause damage to the inside of the product.
•• For wall mounts that do not comply with the VESA standard screw specifications, the length of the screws may
differ depending on the wall mount specifications.
•• Do not fasten the screws too firmly. This may damage the product or cause the product to fall, leading to
personal injury. Samsung is not liable for these kinds of accidents.
•• Samsung is not liable for product damage or personal injury when a non-VESA or non-specified wall mount is
used or the consumer fails to follow the product installation instructions.
•• Do not mount the product at more than a 15 degree tilt.
•• Always have at least two people mount the product on a wall.
•• Standard dimensions for wall mount kits are shown in the table below.
Model Name
VESA screw hole specs (A * B) in
millimetres (inches)
QB43N / QB49N / QB55N /
QM43N / QM49N / QM55N
200 × 200 (7.9 × 7.9)
QB65N / QB75N / QM65N /
QM75N
400 × 400 (15.7 × 15.7)
Standard Screw
Quantity
M8
4
"" Do not install your Wall Mount Kit while your product is turned on. It may result in personal injury due to electric
shock.
22
Chapter 03
Connecting and Using a Source Device
Before Connecting
Pre-connection Checkpoints
"" Before connecting a source device, read the user manual provided with the product.
The number and locations of ports on source devices may differ from device to device.
"" Do not connect the power cable until all connections are completed.
Connecting the power cable during connection may damage the product.
"" Check the types of ports at the back of the product you want to connect.
Connecting to a PC
•• Do not connect the power cable before connecting all other cables.
Ensure you connect a source device first before connecting the power cable.
•• A PC can be connected to the product in a variety of ways.
Select a connection method suitable for your PC.
"" Connecting parts may differ in different products.
Connection Using an HDMI Cable
"" We recommend using authorised cables for HDMI or DP cable connections.
HDMI IN
23
Connection Using an DP Cable
Connection using a DVI cable (Digital type)
"" You can use the DVI port on the product as an HDMI port by using a DVI-HDMI adapter.
"" Audio is not available if the DVI port on the product is connected to the HDMI port on the PC
using a DVI-HDMI adapter.
DP IN
DVI/MAGICINFO IN
•• Precautions for using DP
"" Some graphics cards that are not compliant with the DP standard may prevent the
Windows Booting/Bios screen from being displayed when the product is in power-saving
mode. If this is the case, make sure to turn on the product first before turning on your
PC.
DVI/HDMI AUDIO IN
"" The interface DP IN on the product and the provided DP cable are designed based on the
VESA standards. Using a DP cable that is not VESA compliant may cause the product to
function improperly. Samsung Electronics shall not be held responsible for any issues
from using a cable that is not VESA compliant.
Make sure to use a DP cable that is VESA compliant.
"" To use the optimal resolution (3840 x 2160 @ 60Hz) when the input source is
DisplayPort, using a DP cable shorter than 5m is recommended.
DVI/MAGICINFO IN
HDMI
"" Disabling power-saving mode when the input source is DisplayPort may import new
resolution information and reset the task window size or location.
24
Connection Using an HDMI-DVI Cable
After connecting a computer to the product with an HDMI-DVI cable, make sure to configure the
settings as shown below to enable the video and audio from the computer.
•• Sound → set HDMI Sound to PC(DVI)
•• System → General → set HDMI Hot Plug to Off
HDMI IN
DVI/HDMI AUDIO IN
25
Connecting an External Monitor
•• Do not connect the power cable before connecting all other cables.
Ensure you connect a source device first before connecting the power cable.
"" Connecting parts may differ in different products.
"" Only the ports that are marked as DAISY CHAIN are supported.
"" Use a cable shorter than 10 feet (3m) to get the best UHD content viewing quality.
"" Maximum loopouts: Up to 4 are supported if HDCP 2.2 is supported, up to 7 if HDCP 1.4 is supported, and up to 9 if HDCP is not supported.
"" Setting Anynet+ (HDMI-CEC) to On while using a daisy chain connection may cause malfunction.
PC
Monitor 1
Monitor 2
Monitor 3
Monitor 4
DP IN
HDMI OUT
(DAISY CHAIN IN) (DAISY CHAIN OUT)
HDMI IN
HDMI OUT
(DAISY CHAIN IN) (DAISY CHAIN OUT)
HDMI IN
HDMI OUT
(DAISY CHAIN IN) (DAISY CHAIN OUT)
HDMI IN
HDMI OUT
(DAISY CHAIN IN) (DAISY CHAIN OUT)
HDMI IN
HDMI OUT
(DAISY CHAIN IN) (DAISY CHAIN OUT)
HDMI IN
HDMI OUT
(DAISY CHAIN IN) (DAISY CHAIN OUT)
HDMI IN
HDMI OUT
(DAISY CHAIN IN) (DAISY CHAIN OUT)
HDMI IN
HDMI OUT
(DAISY CHAIN IN) (DAISY CHAIN OUT)
26
Connecting to a Video Device
•• Do not connect the power cable before connecting all other cables.
Ensure you connect a source device first before connecting the power cable.
•• You can connect a video device to the product using a cable.
"" Connecting parts may differ in different products.
"" Press the SOURCE button on the remote control to change the source.
Connection Using an HDMI-DVI Cable
•• Audio will not be enabled if the product is connected to a video device using an HDMI-DVI
cable. To resolve this, additionally connect an audio cable to the audio ports on the product
and video device.
•• After connecting a video device to the product with an HDMI-DVI cable, make sure to
configure the settings as shown below to enable the video and audio from the video device.
You can use the DVI port on the product as an HDMI port by using a DVI-HDMI adapter. Audio
is not available if the DVI port on the product is connected to the HDMI port on the PC using
a DVI-HDMI adapter.
HDMI IN
DVI/HDMI AUDIO IN
–– Sound → set HDMI Sound to AV(HDMI)
–– System → General → set HDMI Hot Plug to On
DVI/MAGICINFO IN
HDMI
"" Supported resolutions include 1080p (50/60Hz), 720p (50/60Hz), 480p, and 576p.
27
Connection Using an HDMI Cable
Connecting to an Audio System
Using an HDMI cable or HDMI to DVI Cable (UHD 30Hz)
"" Connecting parts may differ in different products.
•• An HDMI cable supports digital video and audio signals, and does not require an audio cable.
•• The picture may not display normally (if at all) or the audio may not work if an external
device that uses an older version of HDMI mode is connected to the product. If such a
problem occurs, ask the manufacturer of the external device about the HDMI version and, if
out of date, request an upgrade.
AUDIO OUT
•• Be sure to use an HDMI cable with a thickness of 14 mm or less.
•• Be sure to purchase a certified HDMI cable. Otherwise, the picture may not display or a
connection error may occur.
•• A basic high-speed HDMI cable or one with ethernet is recommended.
This product does not support the ethernet function via HDMI.
HDMI IN
Connecting the LAN Cable
"" Connecting parts may differ in different products.
RJ45
•• Use Cat7(*STP Type) cable for the connection. (10/100 Mbps)
*Shielded Twist Pair
28
Changing the Input source
Source allows you to select a variety of sources and change source device names.
You can display the screen of a source device connected to the product. Select a source from
source list to display the screen of the selected source.
"" The input source can also be changed by using the SOURCE button on the remote control.
Source
"" The screen may not display correctly if an incorrect source is selected for the source device
you want to convert to.
SOURCE
Edit
Source
SOURCE → u → Edit → ENTER E
MagicInfo S
Web Browser
Screen Mirroring Remote Workspace
"" The displayed image may differ depending on the model.
HDMI 1
HDMI 2
DisplayPort
Edit the name and device type of a connected external device.
•• The list can include the following source devices. Source devices on the list differ depending
on the selected source.
HDMI 1 / HDMI 2 / DisplayPort / DVI / Cable Box / Game Console / PC / Blu-ray player
•• You cannot edit the following sources.
MagicInfo S / URL Launcher / Web Browser / Screen Mirroring / Remote Workspace
Information
INFO
You can see detailed information about the selected external device.
29
Web Browser
SOURCE →
Web Browser → ENTER E
"" Connect the network to access the Internet from the product like accessing the Internet
from a computer.
Settings
SOURCE →
Advanced Settings
General
Hide Tabs and Toolbar
automatically
If the browser tabs, menu or toolbar are not used for a while,
they will automatically disappear. To make them appear again,
move the pointer or focus to the top of the screen.
•• Use / Do not use
Web Browser → u → Settings → ENTER E
Refresh Interval
Set the time for the web browser to wait before returning to the home page.
•• Off / 5 min / 10 min / 15 min / 30 min
Zoom
Set the zoom scale to apply when the web browser is refreshed.
Hide Cursor in Touch Mode
Pop-up Blocker
Hide the cursor to prevent interference with touch operation.
•• Use / Do not use
Make your browsing experience more pleasant by blocking popup windows.
•• Use / Do not use
Reset Settings
All your customised Web Browser settings will be reset to their
default values. Your bookmarks and history won't be affected.
•• 50% / 75% / 100% / 125% / 150% / 200% / 300%
Home Page
Search Engine
Set the website to display when the web browser is refreshed.
If you enter a keyword in the URL/keyword input field, Web Browser will open the Search
Results page. Choose the search engine you want to use.
•• Samsung Display / Custom
Custom
•• Google / Bing
Enter the URL to set as the home page.
•• Enter URL
"" Available only when Home Page is set to Custom.
30
Remote Workspace
Privacy & Security
Do Not Track
Delete History
JavaScript
Delete browsing data
Ask websites not to track you.
•• Use / Do not use
Delete your entire browsing history.
Allow all sites to run JavaScript for a better browsing experience.
•• Use / Do not use
Delete all browsing data such as cookies, cached images and
data. Your bookmarks and history won't be affected.
SOURCE →
Remote Workspace → ENTER E
This function allows you to connect your product to a remote PC or a cloud server.
Enter the address of the PC or cloud server you want to connect to. Then, follow the on-screen
instructions.
"" Make sure that the product is connected to the network.
"" This function is supported when the operating system of the PC or cloud server is Windows
Vista or later.
"" Be sure to connect your keyboard and mouse before starting this function.
Encoding
Encoding
Choose an encoding method for web pages. The current setting
is Auto.
•• Auto / Manual (Current : Unicode)
About
Display the current version of Web Browser.
31
Chapter 04
Multiple Display Control
Control multiple display devices connected to a PC simultaneously.
Cable Connection
•• Pin assignment
1 2 3 4 5
5 4 3 2 1
6 7 8 9
9 8 7 6
RS232C Cable
Interface
RS232C (9 pins)
Pin
TxD (No.2), RxD (No.3), GND (No.5)
Bit rate
9600 bps
Data bits
8 bit
Parity
None
Stop bit
1 bit
Flow control
None
Maximum length
15 m (only shielded type)
<Male type>
<Female type>
Pin
Signal
Pin
Signal
1
Detect data carrier
6
Prepare data set
2
Received data
7
Send request
3
Transmitted data
8
Clear to send
4
Prepare data terminal
9
Ring indicator
5
Signal ground
32
LAN Cable
•• RS232C cable
Connector: 9-Pin D-Sub to Stereo Cable
•• Pin assignment
6
3
2
1
1
1 2 3 4 5 6 7 8
-P2-
9
-P1-
5
-P1-
Male type
-P1-
-P2-
-P2-
Rx
3
1
Tx
STEREO
Tx
2
2
Rx
PLUG
Gnd
5
3
Gnd
(3.5ø)
Pin No
Standard Colour
Signal
1
White and orange
TX+
2
Orange
TX-
3
White and green
RX+
4
Blue
NC
5
White and blue
NC
6
Green
RX-
7
White and brown
NC
8
Brown
NC
33
Cross LAN cable (PC to PC)
•• Connector : RJ45
Direct LAN cable (PC to HUB)
HUB
RJ45
RJ45
P2
RJ45
P1
P2
P1
P1
P2
Signal
P1
P2
Signal
TX+
1
3
RX+
TX-
2
6
RX-
Signal
P1
P2
Signal
RX+
3
1
TX+
TX+
1
1
TX+
RX-
6
2
TX-
TX-
2
2
TX-
RX+
3
3
RX+
RX-
6
6
RX-
34
Connection
•• Connection 2
"" Ensure you connect each of the adapters to the correct RS232C IN or OUT port on the
product.
PC
Monitor 1
Monitor 2
Monitor 3
RJ45
RJ45
•• Connection 1
PC
Monitor 1
RS232C IN
RS232C OUT
Monitor 2
RS232C IN
RS232C OUT
Monitor 3
RS232C IN
RS232C OUT
Monitor 4
RS232C IN
RJ45
RJ45
RS232C OUT
•• Connection 3
PC
RJ45
Monitor 1
RJ45
RS232C OUT
Monitor 2
RS232C IN
RS232C OUT
Monitor 3
RS232C IN
RS232C OUT
Monitor 4
RS232C IN
RS232C OUT
35
Control Codes
•• All communications take place in hexadecimals. The checksum is calculated by adding up
all values except the header. If a checksum adds up to be more than 2 digits as shown below
(11+FF+01+01=112), the first digit is removed.
Viewing control state (Get control command)
E.g. Power On & ID=0
Header
Command
0xAA
Command type
ID
Data length
Checksum
0
Controlling (Set control command)
Header
Command
0xAA
Command type
ID
Data length
Data
1
Value
Checksum
Header
Command
0xAA
0x11
Header
Command
0xAA
0x11
ID
ID
Data length
Data 1
1
"Power"
Data length
Data 1
1
1
Checksum
12
•• To control all devices connected by a serial cable simultaneously irrespective of IDs, set the
ID as "0xFE" and transmit commands. Commands will be executed by each device but ACK
will not respond.
Command
No.
Command type
Command
Value range
1
Power control
0x11
0~1
2
Volume control
0x12
0~100
3
Input source control
0x14
-
4
Screen size control
0x19
0~255
5
Video wall mode control
0x5C
0~1
6
Safety Lock
0x5D
0~1
7
Video Wall On
0x84
0~1
8
Video Wall User Control
0x89
-
36
Power control
Volume control
•• Function
A product can be powered on and off using a PC.
•• Function
The volume of a product can be adjusted using a PC.
•• Viewing power state (Get Power ON / OFF Status)
•• Viewing volume state (Get Volume Status)
Header
Command
0xAA
0x11
Data length
ID
Checksum
0
•• Setting power ON/Off (Set Power ON / OFF)
Header
Command
0xAA
0x11
ID
Header
Command
0xAA
0x12
Data length
ID
Checksum
0
•• Setting the volume (Set Volume)
Data length
Data
1
"Power"
Checksum
Header
Command
0xAA
0x12
ID
Data length
Data
1
"Volume"
"Power": Power code to be set on a product.
"Volume": Volume value code to be set on a product. (0-100)
1: Power ON
•• Ack
0: Power OFF
•• Ack
Header
Command
0xAA
0xFF
ID
Data length
Ack/Nak
r-CMD
Val1
3
'A'
0x11
"Power"
Checksum
•• Nak
Command
0xAA
0xFF
ID
Data length
Ack/Nak
r-CMD
Val1
3
'N'
0x11
"ERR"
Command
0xAA
0xFF
ID
Data length
Ack/Nak
r-CMD
Val1
3
'A'
0x12
"Volume"
Checksum
"Volume": Volume value code to be set on a product. (0-100)
•• Nak
"Power": Power code to be set on a product.
Header
Header
Checksum
Checksum
Header
Command
0xAA
0xFF
ID
Data length
Ack/Nak
r-CMD
Val1
3
'N'
0x12
"ERR"
Checksum
"ERR" : A code showing what error has occurred.
"ERR" : A code showing what error has occurred.
37
Input source control
•• Ack
Header
•• Function
The input source of a product can be changed using a PC.
0xAA
•• Viewing input source state (Get Input Source Status)
Header
Command
0xAA
0x14
Data length
ID
0
Command
0xAA
0x14
ID
0xFF
ID
Data length
Ack/Nak
r-CMD
Val1
3
'A'
0x14
"Input
Source"
Checksum
"Input Source": An input source code to be set on a product.
Checksum
•• Nak
•• Setting the input source (Set Input Source)
Header
Command
Data length
Data
1
"Input Source"
Checksum
Header
Command
0xAA
0xFF
ID
Data length
Ack/Nak
r-CMD
Val1
3
'N'
0x14
"ERR"
Checksum
"ERR" : A code showing what error has occurred.
"Input Source": An input source code to be set on a product.
0x18
DVI
0x0C
Input source
0x20
MagicInfo
0x1F
DVI_video
0x21
HDMI1
0x22
HDMI1_PC
0x23
HDMI2
0x24
HDMI2_PC
0x25
DisplayPort
"" DVI_video, HDMI1_PC and HDMI2_PC cannot be used with the Set command. They only
respond to "Get" commands.
"" MagicInfo is only available with models that contain the MagicInfo function.
38
Screen size control
Video Wall Mode Control
•• Function
The screen size of a product can be changed using a PC.
•• Function
Video Wall mode can be activated on a product using a PC.
This control is only available on a product whose Video Wall is enabled.
•• Viewing the screen size (Get Screen Size Status)
Header
Command
0xAA
0x19
•• Viewing video wall mode (Get Video Wall Mode)
Data length
ID
Checksum
0
•• Ack
Header
0xAA
Command
ID
0xFF
Data
length
Ack/Nak
3
'A'
r-CMD
0x19
Val1
Header
Command
0xAA
0x5C
Data length
ID
0
Checksum
•• Setting the video wall (Set Video Wall Mode)
Checksum
"Screen Size"
Header
Command
0xAA
0x5C
ID
Data length
Data
1
"Video Wall Mode"
"Screen Size": product screen size (range: 0 – 255, unit: inch)
"Video Wall Mode": A code used to activate Video Wall mode on a product
•• Nak
1: Full
Header
Command
0xAA
0xFF
ID
Data
length
Ack/Nak
r-CMD
Val1
3
'N'
0x19
"ERR"
"ERR": A code showing what error has occurred
Checksum
0: Natural
Checksum
•• Ack
Header
Command
ID
0xAA
0xFF
Data
length
Ack/Nak
3
'A'
r-CMD
Val1
0x5C
"Video Wall
Mode"
Checksum
"Video Wall Mode": A code used to activate Video Wall mode on a product
•• Nak
Header
Command
0xAA
0xFF
ID
Data
length
Ack/Nak
r-CMD
Val1
3
'A'
0x5C
"ERR"
Checksum
"ERR": A code showing what error has occurred
39
Safety Lock
Video Wall On
•• Function
PC can be used to turn the Safety Lock On function on or off on a product.
•• Function
Turn Video Wall on or off on the product from your computer.
This control is available regardless of whether or not the power is turned on.
•• Get Video Wall On/Off Status
•• Viewing the safety lock state (Get Safety Lock Status)
Header
Command
0xAA
0x5D
Data length
ID
Checksum
0
Command
0xAA
0x5D
ID
Command
0xAA
0x84
Data length
Data
1
"Safety Lock"
Checksum
Header
Command
0xAA
0x84
1: Video Wall ON
1: ON
0: Video Wall OFF
0: OFF
•• Ack
•• Ack
Command
0xAA
0xFF
ID
Data
length
Ack/Nak
r-CMD
Val1
3
'A'
0x5D
"Safety Lock"
Checksum
•• Nak
Command
0xAA
0xFF
ID
Data
length
Ack/Nak
r-CMD
Val1
3
'N'
0x5D
"ERR"
ID
Data length
Data
1
V.Wall_On
Checksum
Header
Command
0xAA
0xFF
ID
Data length
Ack/Nak
r-CMD
Val1
3
'A'
0x84
V.Wall_On
Data length
Ack/Nak
r-CMD
Val1
3
'N'
0x84
ERR
Checksum
V.Wall_On : Same as above
•• Nak
"Safety Lock": Safety lock code to be set on a product
Header
Checksum
0
•• V.Wall_On: Video Wall code to be assigned to the product
"Safety Lock": Safety lock code to be set on a product
Header
Data length
ID
•• Set Video Wall On/Off
•• Enabling or disabling safety lock (Set Safety Lock Enable / Disable)
Header
Header
Checksum
Header
Command
0xAA
0xFF
ID
Checksum
"ERR": A code showing what error has occurred
"ERR": A code showing what error has occurred
40
Video Wall User Control
Wall_SNo: Product Number code assigned to the product
10x10 Video Wall Model : ( 1 ~ 100)
•• Function
Turn the Video Wall function on or off on the product from your computer.
•• Get Video Wall Status
Header
Command
0xAA
0x89
ID
Data length
Checksum
0
•• Set Video Wall
Header
Command
0xAA
0x89
ID
Data length
Val1
Val2
2
Wall_Div
Wall_SNo
Checksum
Set Number
Data
1
0x01
2
0x02
...
...
99
0x63
100
0x64
•• Ack
Header
Command
0xAA
0xFF
ID
Data
length
Ack/Nak
r-CMD
Val1
Val2
4
'A'
0x89
Wall_Div
Wall_
SNo
Data length
Ack/Nak
r-CMD
Val1
3
'N'
0x89
ERR
Checksum
•• Nak
Header
Command
0xAA
0xFF
ID
Checksum
"ERR": A code showing what error has occurred
41
Wall_Div: Video Wall Divider code assigned to the product
10x10 Video Wall Model
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Off
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
1
0x11
0x12
0x13
0x14
0x15
0x16
0x17
0x18
0x19
0x1A
0x1B
0x1C
0x1D
0x1E
0x1F
2
0x21
0x22
0x23
0x24
0x25
0x26
0x27
0x28
0x29
0x2A
0x2B
0x2C
0x2D
0x2E
0x2F
3
0x31
0x32
0x33
0x34
0x35
0x36
0x37
0x38
0x39
0x3A
0x3B
0x3C
0x3D
0x3E
0x3F
4
0x41
0x42
0x43
0x44
0x45
0x46
0x47
0x48
0x49
0x4A
0x4B
0x4C
0x4D
0x4E
0x4F
5
0x51
0x52
0x53
0x54
0x55
0x56
0x57
0x58
0x59
0x5A
0x5B
0x5C
0x5D
0x5E
0x5F
6
0x61
0x62
0x63
0x64
0x65
0x66
0x67
0x68
0x69
0x6A
0x6B
0x6C
0x6D
0x6E
0x6F
7
0x71
0x72
0x73
0x74
0x75
0x76
0x77
0x78
0x79
0x7A
0x7B
0x7C
0x7D
0x7E
N/A
8
0x81
0x82
0x83
0x84
0x85
0x86
0x87
0x88
0x89
0x8A
0x8B
0x8C
N/A
N/A
N/A
9
0x91
0x92
0x93
0x94
0x95
0x96
0x97
0x98
0x99
0x9A
0x9B
N/A
N/A
N/A
N/A
10
0xA1
0xA2
0xA3
0xA4
0xA5
0xA6
0xA7
0xA8
0xA9
0xAA
N/A
N/A
N/A
N/A
N/A
11
0xB1
0xB2
0xB3
0xB4
0xB5
0xB6
0xB7
0xB8
0xB9
N/A
N/A
N/A
N/A
N/A
N/A
12
0xC1
0xC2
0xC3
0xC4
0xC5
0xC6
0xC7
0xC8
N/A
N/A
N/A
N/A
N/A
N/A
N/A
13
0xD1
0xD2
0xD3
0xD4
0xD5
0xD6
0xD7
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
14
0xE1
0xE2
0xE3
0xE4
0xE5
0xE6
0xE7
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
15
0xF1
0xF2
0xF3
0xF4
0xF5
0xF6
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
42
Using MDC
Multiple display control "MDC" is an application that allows you to easily control multiple
display devices simultaneously using a PC.
For details on how to use the MDC programme, refer to Help after installing the programme.
The MDC programme is available on the website.
"" If you press the On or Off button located at the top left of the screen, the product checks its
status for about one minute. To run other commands, try after the one minute.
"" For details on how to connect devices for multiple display control, refer to page 35.
MDC Programme Installation/Uninstallation
9 Click "Finish" in the displayed "InstallShield Wizard Complete" window.
"" Select "Launch MDC Unified" and click "Finish" to run the MDC programme immediately.
10The MDC Unified shortcut icon will be created on the desktop after installation.
"" The MDC execution icon may not be displayed depending on the PC system or product
specifications.
"" Press F5 if the execution icon is not displayed.
Uninstallation
1 Select Settings > Control Panel on the Start menu and double-click Add/Delete Program.
2 Select MDC Unified from the list and click Change/Remove.
Installation
"" MDC installation can be affected by the graphics card, mother board and network
conditions.
1 Click the MDC Unified installation programme.
2 Select a language for installation. Next, click "OK".
3 When the "Welcome to the InstallShield Wizard for MDC_Unified" screen appears, click
"Next".
4 In the "License Agreement" window displayed, select "I accept the terms in the license
agreement" and click "Next".
5 In the displayed "Customer Information" window, fill out all the information fields and click
"Next".
6 In the displayed "Destination Folder" window, select the directory path you want to install
the programme in and click "Next".
"" If the directory path is not specified, the programme will be installed in the default
directory path.
7 In the displayed "Ready to Install the Program" window, check the directory path to install
the programme in and click "Install".
8 Installation progress will be displayed.
43
Chapter 05
Player feature
Accessible using the HOME button on the remote control.
Player
No.
1
HOME
→ Player → ENTER E
Used
199.33 MB
Internal Memory
Filter By: All
1
5
Available
4.26 GB(95%)
Select between internal or external memory.
Play content, templates and schedules configured on the server.
Play a range of content such as channels with schedules assigned, templates or files.
Player
Description
2
Options
•• You can view whether the server is connected (approval) in the Player
screen. To view whether the server is connected when a Network Channel is
running, press INFO on the remote control.
1 Select Network Channel from the Player screen. The No channels message
appears if no channel has been registered in Network Channel.
6
2 Network Channel will run.
No channels
2
Network Channel
3
Network File
4
3
Play content stored on the server.
4
Play a template stored in the internal memory.
5
Select a content type as criterion to search for a desired content list.
6
Set different options for Player.
My Templates
Viewing content
"" The displayed image may differ depending on the model.
"" To use the Player feature, set Play via to MagicInfo in System.
(MENU m → System → Play via → MagicInfo)
1 Select either internal or external memory. The files saved in the selected memory appear.
2 Select the desired file. The content appears on the screen. (For more information on
compatible file formats, see the “File formats compatible with Player” section.)
44
When content is running
Available menu
Control buttons on the remote control
You can play, pause, or skip the content on the playlist by pressing buttons on the remote
control.
Button
TOOLS
INFO
Function
Brings up the menu bar.
Displays the information of the content.
►
Goes to next file or page.
◄
Goes to previous file or page.
E/∆/³
Plays or pauses slide show or video content.
´
Stops displaying content and goes to the Player screen.
π
Rewinds the video content.
µ
Fast forwards the video content.
Press the TOOLS button on the remote control during content playback to configure settings.
Menu
Playlist
Description
View a list of content items currently playing.
Channel List
Network Channel / Internal Channel / USB
Sound Mode
Customises the audio settings for the content currently playing.
Repeat
Background Music
Set the repeat mode.
Set the background music to be played when content is running.
Reset
Reset the background music.
Pause
Pause the background music.
Prev
Play the previous background music on the list.
Next
Play the next background music on the list.
"" Reset, Pause, Prev, Next only appear when the background music is set.
"" If there is only one photo file in the USB, the Slide Show will not play.
"" If the name of a folder is too long on the USB, you cannot select the folder.
45
File Formats Compatible with Player
•• Supported file systems include FAT32 and NTFS.
•• A file with a vertical and horizontal resolution larger than the maximum resolution cannot
be played. Check the vertical and horizontal resolution of the file.
•• Check the supported video and audio Codec types and Versions.
•• Check the supported file versions.
"" PowerPoint version up to 97 – 2013 is supported
Network Schedule Multiframe
Playback restrictions
Sound output restrictions
•• More than one sound output cannot be used.
•• Playback priority: network BGM > local BGM > video file in the main frame selected by the
user
"" Network BGM: Settings can be configured when creating a server schedule.
"" Local BGM: BGM settings can be configured using the tools displayed after the TOOLS
button is pressed during Player playback.
"" User-selected main frame: Main frame settings can be configured when creating a
server schedule.
Template files and LFD(.lfd) files
•• A maximum of two video files (Video) can be played simultaneously.
Restrictions
•• In portrait playback mode, only one video file can be played at a time.
•• Make sure that a distributed folder (content/schedules) exists in Internal Memory or USB
memory.
•• For Office files (PPT and Word files) and PDF files, only one file type is supported at a time.
•• LFD(.lfd) files are not supported.
Playback restrictions
•• A maximum of two video (Video) files can be played.
•• For Office files (PPT and Word files) and PDF files, only one file type is supported at a time.
•• Multiple videos (Video) cannot be played on a single display of a video wall simultaneously.
Sound output restrictions
•• More than one sound output cannot be used.
•• Playback priority: network BGM > local BGM > video file in the main frame selected by the
user
46
Content
File Extension
Container
*.avi
H.264 BP/MP/HP
*.mkv
*.asf
*.wmv
*.mp4
*.mov
*.3gp
*.vro
*.mpg
*.mpeg
*.ts
*.tp
*.trp
*.mov
*.flv
*.vob
Video Codec
Resolution
4096x2160: 30
4096x2160
HEVC (H.265 - Main, Main10)
AVI
MKV
Motion JPEG
Frame rate
(fps)
3840x2160
3840x2160: 60
Bit rate
(Mbps)
Audio Codec
60
60
80
30
80
AC3
MVC
LPCM
MP4
MPEG4 SP/ASP
ADPCM(IMA, MS)
3GP
Window Media Video v9 (VC1)
MOV
MPEG2
ASF
FLV
VRO
Microsoft MPEG-4 v1, v2, v3
PS
Window Media Video v7(WMV1), v8(WMV2)
SVAF
*.svi
HE-AAC
WMA
DD+
MPEG1
VOB
TS
AAC
60
1920x1080
20
Dolby TrueHD
MPEG(MP3)
G.711(A-Law, μ-Law)
H 263 Sorenson
OPUS
30
VP6
*.m2ts
*.mts
*.webm
WebM
*.rmvb
RMVB
VP8
1920x1080
60
20
VP9
3840x2160
3840x2160: 60
80
RV8/9/10 (RV30/40)
1920x1080
60
20
Vorbis
RealAudio 6
47
Video
•• 3D video is not supported.
•• Content with a resolution larger than the resolution
specified in the table above is not supported.
•• Video content with a Bit rate or Frame rate larger than the
rate specified in the table above can cause choppy video
during playback.
•• Video content will not play, or not play correctly, if there is
an error in the content or the container.
•• Some USB/digital camera devices may not be compatible
with the player.
•• Supports up to H.264, Level 4.1
Audio
Image
•• Audio content with a Bit rate or Frame rate larger than the
rate specified in the table above can cause choppy audio
during playback.
•• Compatible image file format : JPEG, PNG, BMP
"" 32-bit, 24-bit and 8-bit BMP files are supported.
•• Audio content will not play, or not play correctly, if there is
an error in the content or the container.
•• Supported maximum file size: 20MB
•• Some USB/digital camera devices may not be compatible
with the player.
•• Supports up to WMA 10 Pro 5.1 channel. WMA lossless audio
is not supported.
•• Supported maximum resolution : 4096 x 4096
•• Supported image effects : 9 effects
(Fade1, Fade2, Blind, Spiral, Checker, Linear, Stairs, Wipe,
Random)
•• QCELP, AMR NB/WB are not supported.
•• H.264 FMO / ASO / RS, VC1 SP / AP L4 and AVCHD are not
supported.
•• For all Video codecs except MVC, VP8, VP6:
–– Below 1280 x 720: 60 frame max
–– Above 1280 x 720: 30 frame max
•• GMC 2 or higher is not supported.
•• Supports only BD MVC Spec.
•• When a single video file is playing, Seamless mode is not
supported under the following conditions:
–– Incompatible codec (MVC, VP3, MJPEG) ↔ Incompatible
codec
–– Incompatible codec ↔ Compatible codec
–– The resolution is different from that of the monitor
–– The frequency is different from that of the monitor
48
Power Point
•• Compatible document file formats
–– Extension : ppt, pptx
–– Version : Office 97 ~ Office 2013
•• Functions not supported
–– Animation effect
–– 3D shapes (which will be displayed in 2D)
–– Header and footer (some subitems are not supported)
–– Word Art
–– Align
A group alignment error may occur
–– Office 2007
SmartArt is not fully supported. 97 out of 115 subitems
are supported.
––
––
––
––
––
Object insertion
Half-width characters
Letter spacing
Charts
Vertical text
Some subitems are not supported
PDF
•• Compatible document file formats
–– Extension : pdf
•• Functions not supported
–– Content less than 1 pixel not supported because of
performance degradation issue.
–– Masked Image, Tiled Image content not supported.
–– Content with Rotated Text, not supported.
–– 3D Shadow Effects not supported.
–– Some characters not supported
(Special characters may be corrupted)
WORD
•• Compatible document file formats
–– Extension : .doc, .docx
–– Version : Office 97 ~ Office 2013
•• Functions not supported
–– Page background effect
–– Some paragraph styles
–– Word Art
–– Align
A group alignment error may occur
–– 3D shapes (which will be displayed in 2D)
–– Office 2007
SmartArt is not fully supported. 97 out of 115 subitems
are supported.
––
––
––
––
Charts
Half-width characters
Letter spacing
Vertical text
Some subitems are not supported
–– Slide notes and handout
–– Slide notes and handout
49
Template files
•• Playback is only available in My Templates.
LFD
•• Supported in Network Channel
•• Compatible document file formats
–– Extension: .lfd
50
Schedule
HOME
You can check the schedule imported from a selected storage device.
No.
→ Schedule → ENTER E
Schedule
Internal Memory
Sunday, January 14 08:45 AM
Schedule your content on a local channel.
Send
Description
1
Select the saved location of the schedule.
2
View schedule of content playback.
Delete
Select to create a
new schedule on this
channel
CH 2
The default content will be played when there is no programme scheduled. You can change the default content
from the Options menu.
CH 3
"" The displayed image may differ depending on the model.
51
Clone Product
Export settings on the product to an external storage device. You can also import settings from an external storage
device.
This option is useful when assigning the same settings to several products.
HOME
→ Clone Product → ENTER E
MENU
When a duplicate file is not found on the external storage device
1 Connect the external storage device, then run the Clone Product function.
2 The No cloning file found on the external storage device. Export this device's settings to the external storage
device? message appears.
3 Select Export to export the settings.
When a duplicate file is found on the external storage device
1 Connect the external storage device, then run the Clone Product function.
Clone Product
2 The Cloning file found. Please select an option. message appears.
Run the Import from External Storage or Export to External Storage function.
"" The displayed image may differ depending on the model.
–– Import from External Storage: Copy settings saved on an external storage device to the product.
–– Export to External Storage: Copy settings on the product to an external storage device.
"" After configuration is complete, the product is rebooted automatically.
52
ID Settings
HOME
→ ID Settings → ENTER E
Assign an ID to a set.
Device ID
Set a unique ID number for each product. (Range: 0~224)
"" Press u/d to select a number, and press E.
"" Enter the number you want using the number buttons on the remote control.
Device ID Auto Set
This feature automatically allots an ID number to a device connected via an RS232C cable.
"" This function is only available on the first device within an RS-232C daisy chain.
ID Settings
PC Connection Cable
Select which type of cable you are using to connect the display to the PC.
"" The displayed image may differ depending on the model.
•• RS232C cable
Communicate with MDC via the RS232C-stereo cable.
•• RJ-45 (LAN)/Wi-Fi Network
Communicate with MDC via the RJ45 cable.
53
Video Wall
HOME
→ Video Wall → ENTER E
Customise the layout of multiple displays that are connected to form a video wall.
In addition, display part of a whole picture or repeat the same picture on each of the connected multiple displays.
To display multiple images, refer to MDC Help or the MagicInfo user guide. Some models may not support the
MagicInfo function.
Video Wall
You can activate or deactivate Video Wall.
To organise a video wall, select On.
•• Off / On
Horizontal x Vertical
Video Wall
"" The displayed image may differ depending on the model.
This feature automatically splits a videowall display based on a videowall matrix configuration.
Enter the videowall matrix.
The videowall display is split based on the configured matrix. The number of vertical or horizontal display devices
can be set within the range 1 and 15.
"" A videowall display can be split into a maximum of 225 screens.
"" The Horizontal x Vertical option is only enabled when Video Wall is set to On.
54
Screen Position
To rearrange split screens, adjust the number for each product in the matrix using the Screen Position feature.
Selecting Screen Position will display the videowall matrix with the numbers assigned to the products that form
the videowall.
To rearrange products, use the direction buttons on the remote control to move a product to another desired
number. Press the E button.
"" Screen Position allows you to split the screen into a maximum of 225 views (15 x 15).
"" The Screen Position option is only enabled when Video Wall is set to On.
"" To use the function, make sure Horizontal x Vertical is configured.
Format
Select how to display images on the videowall display.
•• Full: Display images in full screen with no margin.
•• Natural: Display images in the original aspect ratio without enlarging or reducing the size.
"" The Format option is only enabled when Video Wall is set to On.
55
Network Status
HOME
Check the current network and Internet connection.
→ Network Status → ENTER E
Network Status
"" The displayed image may differ depending on the model.
56
On/Off Timer
HOME
→ On/Off Timer → ENTER E
"" You must set Clock Set before you can use this feature.
On Timer
Set On Timer so that your product turns on automatically at a time and on a day of your choice.
The power is turned on with the specified volume or input source.
On Timer: Set the on timer by making a selection from one of the seven options. Ensure you set the current time
first.
(On Timer 1 ~ On Timer 7)
"" While the internal/USB memory option can be used with On Timer, it is recommended to use an internal
memory.
"" Proper operation of On Timer feature cannot be guaranteed if used with a battery powered USB device, which
can take longer to be recognised.
On/Off Timer
"" The displayed image may differ depending on the model.
•• Setup: Select Off, Once, Everyday, Mon~Fri, Mon~Sat, Sat~Sun or Manual. If you select Manual, you can choose
the days you want On Timer to turn on your product.
–– The check mark indicates days you’ve selected.
•• Time: Set the hour and minute. Use the number buttons or the up and down arrow keys to enter numbers. Use
the left and right arrow buttons to change entry fields.
•• Volume: Set the desired volume level. Use the up and down arrow buttons to change the volume level.
•• Source: Select the input source of your choice.
•• Content (when the Source is set to Internal/USB): From the USB device or internal memory, select a file (e.g.
music, photo, or video) to play just after the product is turned on.
57
Off Timer
Set the off timer (Off Timer) by making a selection from one of the seven options. (Off Timer 1 ~ Off Timer 7)
•• Setup: Select Off, Once, Everyday, Mon~Fri, Mon~Sat, Sat~Sun or Manual. If you select Manual, you can choose
the days you want Off Timer to turn off your product.
–– The check mark indicates days you’ve selected.
•• Time: Set the hour and minute. Use the number buttons or the up and down arrow keys to enter numbers. Use
the left and right arrow buttons to change entry fields.
Holiday Management
Timer will be disabled during a period specified as a holiday.
•• Add Holiday: Specify the period you want to add as a holiday.
Select the start and end dates of the holiday you want to add using the u/d buttons, and click the Done
button.
The period will be added to the list of holidays.
–– Start Date: Set the start date of the holiday.
–– End Date: Set the end date of the holiday.
•• Delete: Delete selected items from the list of holidays.
•• Edit: Select a holiday item and then change the date.
•• Set Applied Timer: Set the On Timer and Off Timer to not activate on public holidays.
–– Press E to select the On Timer and Off Timer settings you do not want to activate.
–– The selected On Timer and Off Timer will not activate.
58
Ticker
HOME
Input text while a video or image is displayed and display the text on the screen.
•• Off / On
→ Ticker → ENTER E
•• Message: Enter a message to display on the screen.
•• Time: Set the Start Time and End Time to display a Message.
•• Font options: Specify the text font and colour for the message.
•• Position: Select an orientation to display a Message.
•• Scroll: Specify the scroll Direction and Speed for the message.
•• Preview: Preview configured caption settings.
Ticker
"" The displayed image may differ depending on the model.
59
URL Launcher
HOME
For details on how to use the URL Launcher feature, contact the dealer the product was purchased from.
"" To use the URL Launcher feature, set Play via to URL Launcher in System.
(MENU m → System → Play via → URL Launcher)
→ URL Launcher → ENTER E
URL Launcher
URL Launcher
"" The displayed image may differ depending on the model.
60
URL Launcher Settings
•• Install Web App: Enter URL to install the web application.
•• Install from USB Device: Install the web application from the USB storage device.
•• Uninstall: Remove the installed web application.
HOME
→ URL Launcher Settings → ENTER E
•• Timeout Setting: Set the timeout period for connecting to the URL.
•• Developer Mode: Enable developer mode.
URL Launcher Settings
"" The displayed image may differ depending on the model.
61
Chapter 06
Screen Adjustment
Configure the Picture settings (Backlight, Colour Tone, etc.).
The layout of the Picture menu options may vary depending on the product.
Backlight / Brightness / Contrast
/ Sharpness
Your product has several options for adjusting picture quality.
"" When you make changes to Backlight, Brightness, Contrast or Sharpness, the OSD will be adjusted accordingly.
"" You can adjust and store settings for each external device you have connected to an input on the product.
"" Lowering picture brightness reduces power consumption.
MENU m → Picture → ENTER E
Picture
Backlight
100
Brightness
45
Contrast
70
Sharpness
50
Colour Temperature
10000 K
Advanced Settings
Picture Options
"" The displayed image may differ depending on the model.
62
Colour Temperature
MENU m → Picture → Colour Temperature → ENTER E
It sets colour temperature. The value and temperature increase simultaneously, so the ratio of blue colour rises.
(Range: 2800K–16000K)
"" Enabled when Colour Tone is set to Off.
Picture
Colour Temperature
10000 K
"" The displayed image may differ depending on the model.
63
Advanced Settings
Configure advanced picture settings to create your preferred picture.
MENU m → Picture → Advanced Settings → ENTER E
Picture Enhancer
Displays enhanced colour and sharpness.
•• Off / On
Advanced Settings
Picture Enhancer
On
HDR+ Mode
HDR+ Mode
Off
Automatically provide an optimal HDR effect based on the video source.
Colour
50
Tint (G/R)
0
・
BT.1886
Colour
Adjust the colour saturation levels. Colour saturation intensifies as the value nears 100. (Range: 0~100)
White Balance
Gamma
•• Off / On
BT.1886
0
Tint (G/R)
Adjust the ratio of green to red tint levels. Increasing values intensifies the saturation of red and green colours.
(Range: 0~50)
"" The displayed image may differ depending on the model.
64
White Balance
Gamma
Adjust the colour temperature of the picture so that white objects appear brighter.
Adjust the primary colour intensity.
2 Point
Adjust red, green, and blue luminosity levels in two sections for precise white balance
optimisation.
•• R-Offset / G-Offset / B-Offset: Adjust the proportion of each of red, green and blue colours
in dark areas.
•• R-Gain / G-Gain / B-Gain: Adjust the proportion of each of red, green and blue colours in
bright areas.
•• Reset: Suitable for environments where videowall display are used.
20 Point Settings
•• HLG / ST.2084 / BT.1886 / S Curve
"" The HLG, ST.2084, and BT.1886 sub functions of Gamma vary depending on the input picture
and the HDR+ Mode value. When HDR+ Mode is set to On, all of HLG, ST.2084, and BT.1886
are available.
"" To adjust S Curve, set HDR+ Mode to Off.
HLG / ST.2084 / BT.1886 / S Curve
Adjust the HLG, ST.2084, BT.1886, S Curve levels of the picture.
Contrast Enhancer
Controls the white balance in 20 point interval by adjusting the red, green, and blue brightness.
Automatically balance the contrast to prevent excessive differences between bright and dark
areas.
20 Point
•• Off / Low / Medium / High
Adjust red, green, and blue luminosity levels in twenty sections for precise white balance
optimisation.
Black Tone
•• Off (
Select the black level to adjust the screen depth.
) / On (
)
•• Interval: Select interval to adjust.
•• Red: Adjust the red level.
•• Off / Dark / Darker / Darkest
•• Green: Adjust the green level.
•• Blue: Adjust the blue level.
"" Some external devices may not support this function.
65
Flesh Tone
HDMI UHD Color
Emphasise pink Flesh Tone.
Enable to optimise picture quality for HDMI UHD connection.
RGB Only Mode
Fine-tune the saturation and tint of the red, green, and blue colour channels.
•• HDMI1 (Off (
) / On (
))
•• HDMI2 (Off ( ) / On ( ))
"" It supports only the models with UHD resolution.
•• Off / Red / Green / Blue
Motion Lighting
Colour Space Settings
Reduces power consumption by reducing screen brightness when the picture on the screen is
in motion.
Configure colour space settings to refine the spectrum of colours on your screen.
•• Off / On
Colour Space
Choose a colour space.
•• Auto / Native / Custom
"" To adjust Colour, Red, Green, Blue and Reset, set Colour Space to Custom.
66
Picture Options
Colour Tone
Select the colour tone that best suits your viewing preferences.
MENU m → Picture → Picture Options → ENTER E
Picture Options
Colour Tone
Off
Digital Clean View
Off
HDMI Black Level
Auto
Film Mode
Off
Dynamic Backlight
On
•• Off / Cool / Standard / Warm1 / Warm2
"" Settings can be adjusted and stored for each external device connected to an input on the product.
Digital Clean View
Reduce picture noise to avoid distractions such as flickering.
•• Auto / Off
HDMI Black Level
Adjust the black level to optimise the HDMI picture brightness and contrast.
•• Normal / Low / Auto
Film Mode
"" The displayed image may differ depending on the model.
Make frame transitions from older video sources smoother. This function is only available when the input signal is
TV, AV, Component (480i, 1080i), or HDMI (1080i).
•• Off / Auto1 / Auto2
Dynamic Backlight
Automatically adjust the backlight to provide the best possible screen contrast under the current conditions.
•• Off / On
67
Apply Picture Settings
Apply the picture settings to all external devices connected to the device or to the current source only.
•• All Sources / Current Source
MENU m → Picture → Apply Picture Settings → ENTER E
Picture
Apply Picture Settings
All Sources
"" The displayed image may differ depending on the model.
68
Picture Size Settings
Choose size and aspect ratio picture displayed on screen.
MENU m → Picture → Picture Size Settings → ENTER E
・ Fit to screen
Different screen adjustment options are displayed depending on the current input source.
"" Available ports may differ depending on the model.
Picture Size Settings
Picture Size
Picture Size
•• 16:9 Standard: Sets the picture to 16:9 Standard wide mode.
16:9 Standard
Off
・ Zoom and Position
•• Custom: Changes the resolution to suit the user's preferences.
•• 4:3: Sets the picture to basic (4:3) mode.
"" Do not set your product to 4:3 format for a long time.
The borders displayed on the left and right, or top and bottom of the screen may cause image retention
(screen burn) which is not covered by the warranty.
Fit to screen
"" The displayed image may differ depending on the model.
Adjusts the picture position. When selected, the full programme image will be displayed. No part of the image will
be cut off.
•• Off / On / Auto
Zoom and Position
Adjusts the picture zoom and position. This option is available when the input source is set to DVI, HDMI 1, HDMI 2
(1080i/1080p), DisplayPort. Picture Size must be set to Custom for the option to be available.
"" If you want to reset the picture to its original position, select Reset in the Zoom and Position screen. The picture
will be set to its default position.
69
Reset Picture
Restore all picture settings to the factory default.
MENU m → Picture → Reset Picture → ENTER E
Picture
Reset Picture
"" The displayed image may differ depending on the model.
70
Chapter 07
OnScreen Display
Display Orientation
Onscreen Menu Orientation
Configure the menu screen.
MENU m → OnScreen Display → Display Orientation → ENTER E
•• Landscape: Display the menu in landscape mode (default).
•• Portrait: Display the menu in portrait mode on the right side of the product screen.
Display Orientation
Onscreen Menu Orientation
Landscape
Source Content Orientation
Landscape
Aspect Ratio
Full Screen
Source Content Orientation
Rotate the product screen orientation.
•• Landscape: Display the screen in landscape mode (default).
•• Portrait: Display the screen in portrait mode.
Aspect Ratio
"" The displayed image may differ depending on the model.
Set the rotated screen to be either full screen or original.
•• Full Screen: Display the rotated screen in full screen.
•• Original ratio: Display the rotated screen in the original aspect ratio.
"" Available only when Onscreen Menu Orientation is set to Portrait.
"" Available only when Source Content Orientation is set to Portrait.
71
Screen Protection
Auto Protection Time
MENU m → OnScreen Display → Screen Protection → ENTER E
Screen Protection
Auto Protection Time
If the screen displays a still image for a certain period of time you define, the product activates the screen saver to
prevent the formation of burnt in ghost images on the screen.
•• Off / 2 hours / 4 hours / 6 hours / 8 hours / 10 hours
Screen Burn Protection
Off
Screen Burn Protection
To reduce the possibility of screen burn, this unit is equipped with Screen Burn Protection screen burn prevention
technology.
Screen Burn Protection moves the picture slightly on the screen.
The Screen Burn Protection Time setting allows you to programme the time between movements of the picture in
minutes.
"" The displayed image may differ depending on the model.
Pixel Shift
Minimize image retention by finely moving pixels horizontally or vertically.
•• Pixel Shift (Off ( ) / On ( ))
"" Horizontal, Vertical and Time are enabled only when Pixel Shift is set to On.
•• Horizontal: Sets how many pixels the screen moves horizontally.
•• Vertical: Sets how many pixels the screen moves vertically.
•• Time: Set the time interval for performing the horizontal or vertical movement, respectively.
Available Pixel Shift Settings and Optimum Settings.
Available Settings
Optimum Settings
Horizontal (pixels)
0~4
4
Vertical (pixels)
0~4
4
Time (minute)
1 minute ~ 4 minutes
4 minutes
"" The Pixel Shift value may differ depending on the product size (inches) and mode.
"" Displaying a still image or a 4:3 output for an extended period of time may cause image retention. This is not a
defect in the product.
72
Timer
Screen Burn Protection
You can set the timer for Screen Burn Protection.
Pixel Shift
The Screen Burn Protection feature stops automatically after a specified period of time.
Timer
Immediate display
Timer
Off
Off
Repeat: Display the image retention-preventive pattern set in Mode at specified time intervals(Period).
"" The displayed image may differ depending on the model.
Interval: Display the image retention-preventive pattern set in Mode for a specified period of time (from Start Time
to End Time).
"" Mode, Period, Time, Start Time and End Time are enabled only when Timer is set to Repeat or Interval.
•• Mode: Select a screen protective pattern to display.
–– Pixel: Pixels on the screen alternate black continuously.
–– Rolling bar: A vertical bar moves left to right.
–– Fading screen: The entire screen becomes brighter, then darker.
"" The Rolling bar and Fading screen patterns appear only once regardless of the specified repeat period or
time.
•• Period: Specify the time interval to activate the Screen Burn Protection function.
"" The option is enabled when Repeat is selected for Timer.
•• Time: Specify the duration to keep the Screen Burn Protection function on.
"" Enabled when Timer is set to Repeat and Mode is set to Pixel.
•• Start Time: Set the start time to activate the screen protection function.
"" The option is enabled when Interval is selected for Timer.
•• End Time: Set the end time to deactivate the screen protection function.
"" The option is enabled when Interval is selected for Timer.
73
Immediate display
Screen Burn Protection
Select the screen saver you want to display immediately.
Pixel Shift
•• Off / Pixel / Rolling bar / Fading screen
Timer
Immediate display
Off
"" The displayed image may differ depending on the model.
74
Message Display
Source Info
Select whether to display the source OSD when the input source changes.
MENU m → OnScreen Display → Message Display → ENTER E
•• Off / On
No Signal Message
Message Display
Source Info
On
No Signal Message
On
MDC Message
On
Download Status Message
Off
"" The displayed image may differ depending on the model.
Select whether to display the no-signal OSD when no signal is detected.
•• Off / On
MDC Message
Select whether to display the MDC OSD when the product is controlled by the MDC.
•• Off / On
Download Status Message
Select to display the status when downloading content from a server or other device.
•• Off / On
75
Language
Set the menu language.
"" A change to the language setting will only be applied to the onscreen menu display. It will not be applied to
other functions on your PC.
MENU m → OnScreen Display → Language → ENTER E
OnScreen Display
Language
English
"" The displayed image may differ depending on the model.
Reset OnScreen Display
This option returns the current settings under OnScreen Display to the default factory settings.
MENU m → OnScreen Display → Reset OnScreen Display → ENTER E
OnScreen Display
Reset OnScreen Display
"" The displayed image may differ depending on the model.
76
Chapter 08
Sound Adjustment
Configure the sound (Sound) settings for the product.
Sound Mode
You can select a sound mode to suit your personal preferences.
•• Standard: Selects the normal sound mode.
MENU m → Sound → Sound Mode → ENTER E
•• Music: Emphasises music over voices.
•• Movie: Provides the best sound for movies.
•• Clear Voice: Emphasises voices over other sounds.
Sound
Sound Mode
Standard
•• Amplify: Increase the intensity of high-frequency sound to allow a better listening experience for the hearing
impaired.
"" This function is disabled when Sound Output is set to External or Receiver (HDMI).
Balance
Equaliser
HDMI Sound
Sound on Video Call
Sound Output
AV(HDMI)
Current Source
Internal
Auto Volume
"" The displayed image may differ depending on the model.
77
Balance
HDMI Sound
MENU m → Sound → Balance → ENTER E
MENU m → Sound → HDMI Sound → ENTER E
Adjust speaker volume levels for sound balance optimisation.
Select whether to hear from AV(HDMI) or PC(DVI).
•• Balance L/R: Adjusts the balance between the left and right speaker.
•• AV(HDMI) / PC(DVI)
•• Reset: Resets the balance to its default settings.
"" This function is disabled when Sound Output is set to External or Receiver (HDMI).
Equaliser
Sound on Video Call
MENU m → Sound → Sound on Video Call → ENTER E
Select sound output to listen to during a video call.
MENU m → Sound → Equaliser → ENTER E
•• Current Source / Video Call
Adjust the equaliser to customise the volume and pitch, and enhance the richness of the sound
output.
•• 100 Hz / 200 Hz / 500 Hz / 1 kHz / 2 kHz / 5 kHz / 10 kHz (Bandwidth Adjustment): Adjusts
the level of specific bandwidth frequencies.
•• Reset: Resets the equaliser to its default settings.
"" Available only when Sound Mode is set to Standard.
"" This function is disabled when Sound Output is set to External or Receiver (HDMI).
78
Sound Output
Auto Volume
MENU m → Sound → Sound Output → ENTER E
MENU m → Sound → Auto Volume → ENTER E
Select speakers for sound output.
Automatically adjusts the volume level when you change video sources or content so the level
remains the same.
•• Internal / External / Receiver (HDMI)
"" When you set Sound Output to External or Receiver (HDMI), the internal speaker is turned
off.
You will hear sound through the external speakers only. When the Sound Output is set to
Internal, both the product speakers and the external speakers are on. You will hear sound
through both.
"" If there is no video signal, both the products speakers and the external speakers will be
mute.
•• Off ( ) / On ( )
"" To use the volume control of a connected source device, set Auto Volume to Off.
"" This function is disabled when Sound Output is set to External or Receiver (HDMI).
Reset Sound
MENU m → Sound → Reset Sound → ENTER E
The displayed image may differ depending on the model. Reset all sound settings to the factory
defaults.
79
Chapter 09
Network
Network Status
Open Network Settings
MENU m → Network → Network Status → ENTER E
MENU m → Network → Open Network Settings → ENTER E
You can check the current network and Internet status.
Configure network settings to use various smart hub features such as Internet search, content
sharing through a home network and feature updates.
Network Type
•• Wireless / Wired
80
Network Settings (Wired)
•• Depending on how your network is configured, you may be able to attach your product to
your LAN by connecting the LAN port on the back of your product directly to a network wall
outlet using a LAN cable.
See the diagram below. Note that the wall outlet is attached to a modem or router
elsewhere in your house.
Connecting to a Wired Network
There are three ways to attach your product to your LAN using cable.
•• You can attach your product to your LAN by connecting the LAN port on the back of your
product to an external modem using a LAN cable.
See the diagram below.
Modem Cable
RJ45
LAN Cable
•• You can attach your product to your LAN by connecting the LAN port on the back of your
product to an IP Sharer which is connected to an external modem. Use LAN cable for the
connection. See the diagram below.
The Modem Port on the Wall
External Modem
(ADSL / VDSL)
RJ45
LAN
External Modem
(ADSL / VDSL)
The Modem Port on the Wall
LAN
The LAN Port on the Wall
LAN
IP Sharer
(having DHCP server)
RJ45
LAN Cable
If you have a Dynamic Network, you should use an ADSL modem or router that supports
the Dynamic Host Configuration Protocol (DHCP). Modems and routers that support DHCP
automatically provide the IP address, subnet mask, gateway, and DNS values your product
needs to access the Internet so you do not have to enter them manually. Most home networks
are Dynamic Networks.
Some networks require a Static IP address. If your network requires a Static IP address, you
must enter the IP address, subnet mask, gateway, and DNS values manually on your product
Cable Setup Screen when you set up the network connection. To get the IP address, subnet
mask, gateway, and DNS values, contact your Internet Service Provider (ISP).
If you have a Windows computer, you can also get these values through your computer.
"" You can use ADSL modems that support DHCP if your network requires a Static IP address.
"" ADSL modems that support DHCP also let you use Static IP addresses.
Modem Cable
LAN Cable
LAN Cable
81
Set the network connection to use Internet services such as perform software upgrades.
Automatic Open Network Settings (Wired)
Connect to the network using a LAN cable.
Make sure a LAN cable is connected first.
How to set up automatically
1 Set Network Type to Wired from the Open Network Settings page.
2 The network test screen appears and verifies the network connection.
When the connection has been verified, the “Success! Your device is connected to the
Internet. If you have any problems using online services, please contact your Internet
service provider.” message appears.
"" If the connection process fails, check the LAN port connection.
"" If the automatic process cannot find the network connection values or if you want to set the
connection manually, go to the next section, network setup.
How to set up manually
1 Set Network Type to Wired from the Open Network Settings page.
2 The network test screen appears and the verification process starts. Press Cancel. The
verification process stops.
3 Select IP Settings on network connection screen. The IP Settings screen appears.
4 Select the field at the top, press E, and then set IP setting to Enter manually. Repeat the
entry process for each field in the IP Address.
"" Setting IP setting to Enter manually automatically changes DNS setting to Enter
manually.
5 When done, select OK at the bottom of the page, and then press E. The network test
screen appears and the verification process starts.
6 When the connection has been verified, the “Success! Your device is connected to the
Internet. If you have any problems using online services, please contact your Internet
service provider.” message appears.
Manual Open Network Settings (Wired)
Offices may use static IP addresses.
If this is the case, ask the network administrator for the IP address, subnet mask, gateway and
DNS server address. Enter these values manually.
Getting the Network Connection Values
To view the Network connection values on most Windows computers, follow these steps.
1 Right click the Network icon on the bottom right of the screen.
2 In the pop-up menu that appears, click Status.
3 On the dialog that appears, click the Support tab.
4 On the Support Tab, click the Details button. The Network connection values are displayed.
82
Network Settings (Wireless)
Connecting to a Wireless Network
Wireless IP sharer
(router having DHCP server)
The LAN Port on the Wall
Automatic Network Setup (Wireless)
Most wireless networks have an optional security system that requires devices that access the
network to transmit an encrypted security code called an Access or Security Key. The Security
Key is based on a Pass Phrase, typically a word or a series of letters and numbers of a specified
length you were asked to enter when you set up security for your wireless network. If you use
this method of setting up the network connection, and have a Security Key for your wireless
network, you will have to enter the Pass Phrase during the the automatic or manual setup
process.
How to set up automatically
1 Set Network Type to Wireless from the Open Network Settings page.
2 The Network function searches for available wireless networks. When done, it displays a list
LAN Cable
Samsung recommends using IEEE 802.11n. When you play video over a network connection, the
video may not play smoothly.
"" Select a channel for the wireless IP sharer that is not currently being used. If the channel set
for the wireless IP sharer is currently being used by another device nearby, this will result in
interference and communication failure.
"" Your product supports only the following wireless network security protocols.
If you select the Pure High-throughput (Greenfield) 802.11n mode and the Encryption type is
set to WEP, TKIP or TKIP AES (WPS2Mixed) on your AP or wireless router, Samsung products
will not support a connection in compliance with new Wi-Fi certification specifications.
"" If your wireless router supports WPS (Wi-Fi Protected Setup), you can connect to the
network via PBC (Push Button Configuration) or PIN (Personal Identification Number). WPS
will automatically configure the SSID and WPA key in either mode.
"" Connection Methods: You can setup the wireless network connection in three ways.
Auto Setup (Using the Auto Network Search function), Manual Setup, Use WPS
of the available networks.
In the list of networks, press the ▲ or ▼ button to select a network, and then press the E
button twice.
"" If the desired wireless router does not appear, select Refresh to search again.
"" If the router cannot be found after retrying, select the Cancel button.
The Add Network button appears.
3 If the Enter the password for (AP Name). screen appears, go to step 5. If you select a
wireless router that does not have security, go to step 7.
4 If the router has security, enter the Enter the password for (AP Name). (Security key or PIN).
5 When done, use the right arrow button to move the cursor to Done, and then press E. The
network connection screen appears and the verification process starts.
"" A connection with the router is established, but the Internet cannot be accessed.
6 When the connection has been verified, the “Success! Your device is connected to the
Internet. If you have any problems using online services, please contact your Internet
service provider.” message appears.
83
Manual Network Setup (Wireless)
How to set up manually
Offices may use static IP addresses.
1 Set Network Type to Wireless from the Open Network Settings page.
If this is the case, ask the network administrator for the IP address, subnet mask, gateway and
DNS server address. Enter these values manually.
Getting the Network Connection Values
To view the Network connection values on most Windows computers, follow these steps.
1 Right click the Network icon on the bottom right of the screen.
2 In the pop-up menu that appears, click Status.
3 On the dialog that appears, click the Support tab.
4 On the Support Tab, click the Details button. The Network connection values are displayed.
2 The Network function searches for available wireless networks. When done, it displays a list
of the available networks.
3 In the list of networks, press the u or d button to select a network, and then press the E
button twice.
"" If the desired wireless router does not appear, select Refresh to search again.
"" If the router cannot be found after retrying, select the Cancel button.
The Add Network button appears.
4 If the Enter the password for (AP Name). screen appears, go to step 5. If you select a
wireless router that does not have security, go to step 7.
5 If the router has security, enter the Enter the password for (AP Name). (Security key or PIN).
6 When done, use the right arrow button to move the cursor to Done, and then press E. The
network connection screen appears and the verification process starts.
7 Select Cancel while network connections are being attempted. This will stop the
connection.
8 Select IP Settings on network connection screen. The IP Settings screen appears.
9 Select the field at the top, press E, and then set IP setting to Enter manually. Repeat the
entry process for each field in the IP Address.
"" Setting IP setting to Enter manually automatically changes DNS setting to Enter
manually.
10When done, select OK at the bottom of the page, and then press E. The network test
screen appears and the verification process starts.
11 When the connection has been verified, the “Success! Your device is connected to the
Internet. If you have any problems using online services, please contact your Internet
service provider.” message appears.
84
Use WPS
IPv6
How to set up using Use WPS
MENU m → Network → IPv6 → ENTER E
If your router has a Use WPS button, follow these steps.
1 Set Network Type to Wireless from the Open Network Settings page.
Enable or disable IPv6.
•• Off (
) / On (
)
2 Select Use WPS, press E, and then press E again.
3 Press the WPS or PBC button on your wireless router withine the next two minutes. Your
product automatically acquires all the network setting values it needs and connects to your
network.
–– If you want to use the WPS PIN, select WPS PIN.
Go to your wireless router's Settings, enter your PIN, and then select OK.
4 The network connection screen appears, and network setup is done.
IPv6 Status
MENU m → Network → IPv6 Status → ENTER E
Check the status of your IPv6 Internet connection.
85
Server Network Settings
FTP Mode
Specify the FTP operating mode.
MENU m → Network → Server Network Settings → ENTER E
•• Active / Passive
Connect to server
Proxy server
To run Player connect to a network.
Set up your proxy server connection and related functions.
•• Server Address / TLS / Port
"" If the TLS option is enabled, the server is configured to use https and data transfer is
encrypted.
Off / On
"" Enter the server IP address and port number. Use 7001 as the port number. (If unable to
connect to the server using port number 7001, check with your server administrator to find
the correct port number and then change the port number.)
•• Address / Port / ID / Password
"" Address / Port / ID and Password are enabled only when Proxy server is set to On.
"" For the MagicInfo Server user guide, visit the following website: http://displaysolutions.
samsung.com > Support > Resources > MagicInfo Web Manual.
Device Name
MagicInfo Mode
MENU m → Network → Device Name → ENTER E
Select the appropriate MagicInfo Mode depending on the environment where you are using the
product.
This name can be shown on network remote controls over the network.
•• Lite / Premium
Select or enter a device name.
•• [Signage] Display1 ~ 6 / User Input
Server Access
Select a method to connect the server network.
•• Allow / Deny
86
Chapter 10
System
Accessibility
MENU m → System → Accessibility → ENTER E
System
High Contrast
Set the background and font to high-contrast colours in Menu. Menu transparencies become opaque when the
option is selected.
•• Off (
) / On (
)
Enlarge
Accessibility
Enlarge the size of the Menu area.
Start Setup
•• Off (
) / On (
)
Touch Control
Time
Auto Source Switching
Power Control
Eco Solution
"" The displayed image may differ depending on the model.
87
Start Setup
Go through the initial setup steps like you did the first time you used this product.
"" Enter your 4 digit PIN number. The default PIN number is "0-0-0-0".
If you want to change the PIN number, use the Change PIN function.
MENU m → System → Start Setup → ENTER E
System
Start Setup
"" The displayed image may differ depending on the model.
Touch Control
Set the functions related to touch control.
MENU m → System → Touch Control → ENTER E
Touch Control
Prevent touch gestures from controlling your device.
•• Off / On
Touch Control
Touch Control
Off
Admin Menu Lock
Admin Menu Lock
Off
Set the Admin Menu Lock to display the administrator settings menu when you tap and hold the finger on the
screen.
"" The displayed image may differ depending on the model.
•• Off / On
"" Available only when Touch Control is set to On.
88
Time
You can configure Clock Set or DST. Configure various time-related settings.
Clock Set
MENU m → System → Time → ENTER E
Select Clock Set. Select Date or Time, and then press E.
Use the number buttons to enter numbers or press the up and down arrow buttons. Use the left and right arrow
buttons to move from one entry field to the next. Press E when done.
Time
Clock Set
"" You can set the Date and Time directly by pressing the number buttons on the remote control.
NTP Settings
NTP Settings
DST
Power On Delay
Off
0
Set up the server URL and time zone to use the network time.
DST
Switches the DST (Daylight Saving Time) function on or off.
"" The displayed image may differ depending on the model.
Off / On
•• Start Date: Set the start date of Daylight Saving Time.
•• End Date: Set the end date of Daylight Saving Time.
•• Time Offset: Select the correct time offset your timezone.
"" Start Date, End Date and Time Offset are enabled only when DST is set to On.
Power On Delay
When connecting multiple products, adjust the power-on time for each product to prevent power overload (within
the range 0–50 seconds).
89
Auto Source Switching
Turning on the display with Auto Source Switching On, and the previous video source selection is not active, the
display will automatically search the different video input sources for active video.
MENU m → System → Auto Source Switching → ENTER E
Auto Source Switching
When the Auto Source Switching is On, the display video source will automatically be searched for active video.
Auto Source Switching
The Primary Source selection will be activated, if the current video source is not recognised.
Auto Source Switching
Off
Primary Source Recovery
Off
Primary Source
All
Secondary Source
DisplayPort
Secondary Source selection will become active, if no primary video source is available.
If both the primary and secondary input sources are not recognised, the display will perform two searches for an
active source, each search checking the primary and then secondary source. If both searches fail, the display will
return to the first video source and display a message indicating that there is no signal.
Primary Source Recovery
Select whether to restore the selected primary input source when a primary input source is connected.
"" The Primary Source Recovery function is disabled if Primary Source is set to All.
"" The displayed image may differ depending on the model.
Primary Source
Specify Primary Source for the automatic input source.
Secondary Source
Specify Secondary Source for the automatic input source.
"" The Secondary Source function is disabled if Primary Source is set to All.
90
Power Control
Auto Power On
This feature automatically turns on the product as soon as it is plugged in. Pressing the power button is not needed.
MENU m → System → Power Control → ENTER E
PC module power
Power Control
Auto Power On
Off
The PC module can be turned on/off separately from the product.
Synced power-on
PC module power
Max. Power Saving
On
Standby Control
On
Network Standby
Off
Power Button
•• Off / On
Power on only
"" The displayed image may differ depending on the model.
Set to Off to turn on the PC module without turning on the product.
•• Off / On
Synced power-off
Set to Off to turn off the PC module without turning off the product.
•• Off / On
Max. Power Saving
Conserve power by turning off PC monitor when PC is not used for certain time.
•• Off / On
91
Standby Control
Power Control
Auto Power On
Off
PC module power
Max. Power Saving
On
Standby Control
On
Network Standby
Off
Power Button
Power on only
You can set the screen standby mode to be applied when an input signal is received.
•• Auto
Power-saving mode will activate if no input signals are detected even though a source device is connected to
the display.
The message No Signal will appear if no source device is connected.
•• Off
The message No Signal will appear if no input signals are detected.
"" If the message, "No Signal" appears even though a source device is connected, check the cable connection.
"" If No Signal Message is set to Off, the No Signal message does not appear.
In this case, set No Signal Message to On.
•• On
Power-saving mode will activate if no input signals are detected.
"" The displayed image may differ depending on the model.
Network Standby
This feature keeps the network power on when the product turns off.
•• Off / On
Power Button
The power button on the remote control
can be set to turn on the power or turn on or off the power.
•• Power on only: Set the power button on the remote control
•• Power on and off: Set the power button on the remote control
only to turn on the power.
to turn on or off the power.
92
Eco Solution
Energy Saving Mode
Reduce the power consumption by adjusting the screen brightness.
MENU m → System → Eco Solution → ENTER E
Screen Lamp Schedule
Eco Solution
Energy Saving Mode
Off
Screen Lamp Schedule
Off
No Signal Power Off
Auto Power Off
•• Off / Low / Medium / High
15 minutes
Off (Recommended)
Screen Lamp Schedule
Enable or disable the lamp schedule.
•• Off / On
Schedule 1, Schedule 2
Time
"" The displayed image may differ depending on the model.
The panel brightness will change to the brightness set in Lamp at a specified time.
Lamp
Adjust the panel brightness. A value closer to 100 makes the panel brighter.
•• 0 ~ 100
93
No Signal Power Off
Eco Solution
Energy Saving Mode
Off
Screen Lamp Schedule
Off
No Signal Power Off
Auto Power Off
15 minutes
Off (Recommended)
Save power by turning the device off when no signal is received from any source.
•• Off / 15 minutes / 30 minutes / 60 minutes
"" This function does not operate if the display is in the standby mode.
"" The product will automatically power off at a specified time. The time can be changed as required.
Auto Power Off
Choose how long the display will wait before turning off after no user interaction is detected.
•• Off (Recommended) / 4 hours / 6 hours / 8 hours
"" The displayed image may differ depending on the model.
Temperature Control
This function detects the internal temperature of the product. You can specify the temperature range that is
acceptable.
The default temperature is set to 77 °C.
MENU m → System → Temperature Control → ENTER E
"" The screen will become darker if the current temperature exceeds the specified temperature limit. If the
temperature continues to rise, the product will power off to prevent overheating.
System
Temperature Control
The recommended operating temperature for this product is 75 to 80 °C (based on an ambient temperature of 40
°C).
77
"" The displayed image may differ depending on the model.
94
External Device Manager
MENU m → System → External Device Manager → ENTER E
External Device Manager
Manage external devices connected to your signage.
Input Device Manager
Set up keyboards to use with your product. You can add keyboards and configure their setting.
Bluetooth Device List
Input Device Manager
Connect a Bluetooth keyboard, mouse or gamepad to your product.
Device Connection Manager
"" Available for Bluetooth enabled models only.
Keyboard Settings
"" The displayed image may differ depending on the model.
Configure the connected keyboard settings.
Keyboard Language
Set the language of your keyboard.
Keyboard type
Set the type of your keyboard.
95
External Device Manager
Input Device Manager
Device Connection Manager
Device Connection Manager
Allow devices, like smartphones and tablets, on your network to share content with your product.
Access Notification
Display a notification when a device such as a smartphone or tablet, is connected. If you use a Wi-Fi network that
requires a password, turn off this option to automatically connect with devices without viewing notifications.
"" The displayed image may differ depending on the model.
•• Off / First Time Only / Always On
Device List
View and manage connected devices.
96
Play via
Select the appropriate Play via mode depending on the environment where you are using the product.
The home screen may be different depending on the setting.
MENU m → System → Play via → ENTER E
•• MagicInfo / URL Launcher
System
Play via
MagicInfo
"" The displayed image may differ depending on the model.
Change PIN
MENU m → System → Change PIN → ENTER E
Change your 4-digit Personal Identification Number (PIN).
Choose any 4 digits for your PIN and enter it in Enter a new PIN.. Reenter the same 4 digits in Enter the PIN again..
The product has memorised your new PIN.
"" Default password: 0 - 0 - 0 - 0
System
Change PIN
"" The displayed image may differ depending on the model.
97
Security
Safety Lock On
"" Enter your 4 digit PIN number. The default PIN number is "0-0-0-0".
If you want to change the PIN number, use the Change PIN function.
MENU m → System → Security → ENTER E
Turn Safety Lock On on or off. Safety Lock On restricts the actions that can be carried out by the remote control. The
correct PIN must be entered to turn Safety Lock On off.
Security
Power On Button
Safety Lock On
On
Turn on this feature to enable the remote control's Power button to turn on the device while Safety Lock On is
enabled.
Button Lock
Off
•• Off / On
USB Auto Play Lock
Off
Button Lock
Mobile Connection Lock
Off
・ Power On Button
Remote Management
Network Port
Allow
On
This menu can be used to lock the buttons on the product.
Only the remote control can control the product if Button Lock is set to On.
•• Off / On
USB Auto Play Lock
"" The displayed image may differ depending on the model.
Select whether to automatically play MagicInfo content saved on a connected USB device.
•• Off
Play MagicInfo content saved on the USB device automatically.
•• On
Do not play MagicInfo content saved on the USB device automatically.
"" Connecting a USB device containing MagicInfo content displays "USB Auto Play Lock : On" for five seconds.
98
Mobile Connection Lock
Security
Mobile Connection Lock
Remote Management
Off
Allow
Restrict other devices on your network, such as smart phones and tablets, to prevent them from sharing content on
the product.
•• Off / On
Network Port
On
Remote Management
USB Port
On
You can Allow or Deny external commands to access your device via a network.
"" The displayed image may differ depending on the model.
•• Deny / Allow
"" The changed setting remains even after the product is turned off and on using the Power button or Power
switch.
Network Port
Block external network access. You can register networks on the server to allow access.
•• Off / On
USB Port
Block connection to external USB ports.
•• Off / On
99
General
Smart Security
The security provided to protect your display device and connected storage devices against viruses includes.
MENU m → System → General → ENTER E
Scan
General
Inspect your display device and connected storage devices to check for viruses.
Smart Security
Isolated List
Anynet+ (HDMI-CEC)
This is the list of items that have been Isolated for containing viruses.
HDMI Hot Plug
On
Custom Logo
Off
Game Mode
Empty Storage
"" The displayed image may differ depending on the model.
Anynet+ (HDMI-CEC)
Anynet+ is a function that enables you to control all connected Samsung devices that support Anynet+ with your
Samsung product remote control. The Anynet+ system can be used only with Samsung devices that have the
Anynet+ feature. To be sure your Samsung device has this feature, check if there is an Anynet+ logo on it.
•• Off ( ) / On ( )
"" You can only control Anynet+ devices using the product remote control, not the buttons on the product.
"" The product remote control may not work under certain conditions. If this occurs, reselect the Anynet+ device.
"" Anynet+ works when the AV device supporting Anynet+ is in the standby or on status.
"" Anynet+ supports up to 12 AV devices in total. Note that you can connect up to 3 devices of the same type.
100
Troubleshooting for Anynet+
Problem
Possible Solution
•• Check if the device is an Anynet+ device. The Anynet+ system supports Anynet+ devices only.
•• Check if the Anynet+ device power cord is properly connected.
•• Check the Anynet+ device’s Video/Audio/HDMI cable connections.
•• Check whether Anynet+ (HDMI-CEC) is set to On in the System menu.
Anynet+ does not work.
•• Check whether the remote control is Anynet+ compatible.
•• Anynet+ doesn’t work in certain situations. (initial setup)
•• If you have removed and then reconnected the HDMI cable, please make sure to search devices again or turn your
product off and on again.
•• Check if the Anynet+ function of the Anynet device is set on.
I want to start Anynet+.
•• Check if the Anynet+ device is properly connected to the product and check if the Anynet+ (HDMI-CEC) is set to On
in the System menu.
I want to exit Anynet+.
•• Press the SOURCE button on the product remote control and select a non- Anynet+ device.
The message “Disconnecting
Anynet+ device ...” appears on
the screen.
•• You cannot use the remote control when you are configuring Anynet+ or switching to a view mode.
The Anynet+ device does not
play.
•• Use the remote control after the product has completed Anynet+ configuration or has finished switching to Anynet+.
•• You cannot use the play function when initial setup is in progress.
•• Check whether or not the device supports Anynet+ functions.
•• Check whether or not the HDMI cable is properly connected.
•• Check whether Anynet+ (HDMI-CEC) is set to On in the System menu.
The connected device is not
displayed.
•• Search Anynet+ devices again.
•• Anynet+ requires an HDMI connection. Make sure the device is connected to your product with an HDMI cable.
•• Some HDMI cables may not support Anynet+ functions.
•• If the connection is terminated because there has been a power failure or the HDMI cable has been disconnected,
please repeat the device scan.
101
HDMI Hot Plug
General
This feature is used to activate the time delay to turn on a DVI/HDMI source device.
Smart Security
•• Off / On
Anynet+ (HDMI-CEC)
HDMI Hot Plug
On
Custom Logo
Off
Game Mode
Empty Storage
"" The displayed image may differ depending on the model.
Custom Logo
You can download, select, and set the display time of a custom logo that appears when the product turns on.
•• Custom Logo
"" You can select a custom logo (image/video) or turn off the custom logo display.
"" You must download the custom logo from an external USB device to set the custom logo.
•• Logo Display Time
"" If the type of custom logo is Image, you can set the Logo Display Time.
•• Download Logo File
"" You can download a custom logo into the product from an external USB device.
"" The file name of the custom logo you want to download must be saved as “samsung” in all small letters.
"" When there are multiple numbers of external USB connections, the product will attempt to download the
custom logo from the last device that has been connected to the product.
Custom logo file restrictions
•• For image type custom logo, only bitmap files (aRGB 32bpp format) are supported.
•• The resolution of the image type custom logo must be between a minimum of 64 x 64 and the maximum
screen resolution. (Horizontal/Vertical values of the resolution must be multiples of 4.)
•• For video type custom logo, only TS Stream types are supported.
•• The maximum supported video file is 150 MB. The recommended length of a video file is 20 seconds or less.
102
Game Mode
General
When connecting to a game console such as PlayStation™ or Xbox™, you can enjoy a more realistic gaming
experience by selecting game mode.
Smart Security
Anynet+ (HDMI-CEC)
HDMI Hot Plug
On
Custom Logo
Off
Game Mode
•• Off ( ) / On ( )
"" If you connect other external devices while Game Mode is on, the screen may not be in good condition.
Empty Storage
Delete files to make space for new content. Recently played files will not be deleted.
Empty Storage
"" The displayed image may differ depending on the model.
Reset System
This option returns the current settings under system to the default factory settings.
MENU m → System → Reset System → ENTER E
System
Reset System
"" The displayed image may differ depending on the model.
103
Chapter 11
Support
Software Update
Contact Samsung
MENU m → Support → Software Update → ENTER E
MENU m → Support → Contact Samsung → ENTER E
The Software Update menu lets you upgrade your product software to the latest version.
View this information when your product does not work properly or when you want to upgrade
the software.
"" Be careful not to turn off the power until the upgrade is complete. The product will turn off
and on automatically after completing the software upgrade.
"" When you upgrade software, all video and audio settings you have made will return to their
default settings. We advise you to write down your settings so that you can easily reset
them after the upgrade.
Update Now
Update the software to the latest version.
"" Current version: This is the software version already installed in the product.
You can find information regarding our call centres and how to download products and
software.
"" Go to Contact Samsung and find the product Model Code and Software Version.
Terms & Conditions
MENU m → Support → Terms & Conditions → ENTER E
View and set the privacy policy for MagicInfo and other services.
"" Make sure that the product is connected to the network.
Reset All
MENU m → Support → Reset All → ENTER E
This option returns all the current settings for a display to the default factory settings.
104
Chapter 12
Troubleshooting Guide
Requirements Before Contacting Samsung Customer Service Centre
"" Before calling Samsung Customer
Service Centre, test your product
as follows. If the problem persists,
contact Samsung Customer Service
Centre.
Testing the Product
Check if your product is operating normally by using the product test function.
If the screen remains blank while the power indicator blinks even when the product is correctly connected to a PC, perform product testing.
1 Power off both the PC and product.
2 Disconnect all the cables from the product.
3 Power on the product.
4 If No Signal is displayed, the product is operating normally.
If the screen remains blank, check the PC system, video controller and cable.
Checking the Resolution and Frequency
For modes that exceed the supported resolutions, the message "Not Optimum Mode" appears briefly.
Set the PC resolution by referring to Preset Timing Modes.
105
Check the followings.
Installation issue (PC mode)
The screen keeps switching on and off.
Check that the cable between the product and the PC is connected correctly.
The blank spaces found on the screen have nothing to do with the product.
Blank spaces on the screen are caused by the PC or graphics card. To resolve the problem,
Blank spaces are found on all four sides of the screen when adjust the screen size in the HDMI or DVI settings for the graphics card.
an HDMI or HDMI-DVI cable is connected to the product and
If the graphics card settings menu does not have an option to adjust the screen size, update the
PC.
graphics card driver to the latest version.
(Please contact the graphics card or computer manufacturer for further details about how to
adjust the screen settings.)
Screen issue
The power indicator is off. The screen will not switch on.
Make sure that the power cord is connected.
Check that the product is connected correctly with a cable.
No Signal is displayed on the screen.
Check that the device connected to the product is powered on.
Depending on the type of external device, the screen may not display properly. In this case,
connect it with the HDMI Hot Plug function turned On.
Not Optimum Mode is displayed.
This message is displayed when a signal from the graphics card exceeds the product's
maximum resolution and frequency.
Refer to the Standard Signal Mode Table and set the maximum resolution and frequency
according to the product specifications.
The images on the screen look distorted.
Check the cable connection to the product.
The screen is not clear. The screen is blurry.
Set the resolution and frequency to the recommended level.
106
Screen issue
The screen appears unstable and shaky.
There are shadows or ghost images left on the screen.
Check that the resolution and frequency of the PC and graphics card are set within a range
compatible with the product. Then, change the screen settings if required by referring to 'Preset
Timing Modes'.
The screen is too bright. The screen is too dark.
Adjust Brightness and Contrast.
Screen colour is inconsistent.
Go to Picture and adjust the Colour Space Settings settings.
White does not really look white.
Go to Picture and adjust the White Balance settings.
There is no image on the screen and the power indicator
blinks every 0.5 to 1 second.
The product is in power-saving mode.
Press any key on the keyboard or move the mouse to return to the previous screen.
If a PC is connected to the product, check the power status of the PC.
The product will turn off automatically.
Make sure the power cable is connected properly to the product and power outlet.
If the signal from a connected device is not detected, the product automatically turns off after
10 to 15 minutes.
Encoded video content may cause the display to appear corrupted in scenes featuring fast
moving objects such as in a sports event or action video.
The screen display does not look normal.
Low signal level or low picture quality may cause the display to appear corrupted. This does not
mean the product is defective.
A cell phone within a distance of one-meter radius may cause static on analogue and digital
products.
Go to Picture and adjust the screen settings such as Colour, Brightness and Sharpness.
The brightness and colour do not look normal.
Go to System and adjust the Eco Solution settings.
Reset the screen settings to the default settings. (P.70)
107
Screen issue
Check the cable connections.
I see red, green, and blue.
The display looks unstable and then freezes.
This issue may happen when the panel of the product is defective. Contact a Samsung Service
Centre to resolve the issue.
The screen may freeze when a resolution other than the recommended resolution is used or
if the signal is not stable. To resolve the issue, change the PC resolution to the recommended
resolution.
A scaled SD (4:3) content file can cause black bars on both sides of an HD channel screen.
The screen cannot be displayed in full screen.
A video with an aspect ratio different from the product can cause a black bar to appear at the
top and bottom of the screen.
Change the screen size setting to full screen on the product or source device.
Sound issue
There is no sound.
Check the connection of the audio cable or adjust the volume.
Check the volume.
Adjust the volume.
The volume is too low.
If the volume is still low after turning it up to the maximum level, adjust the volume on your PC
sound card or software programme.
108
Sound issue
If an HDMI cable or a DP cable is connected, check the audio output settings on the PC.
Go to Sound and change Sound Output to Internal.
If a source device is used
•• Make sure the audio cable is properly connected to the audio input port on the product.
Video is available but there is no sound.
•• Check the audio output settings for the source device.
(For example, if your monitor is connected to HDMI, you may need to change the audio
option of your video output device to HDMI.)
If a DVI-HDMI cable is used, a separate audio cable is required.
If the product has a headphone port, make sure nothing is connected to it.
Reconnect the power cable to the device and then reboot the device.
Check the cable connection. Make sure a video cable is not connected to an audio input port.
There is static coming from the speakers.
Check the signal strength after connecting a cable.
Low signal level can cause corrupted sound.
Remote control issue
Make sure that the batteries are correctly in place (+/-).
Check if the batteries are flat.
The remote control does not work.
Check for power failure.
Make sure that the power cord is connected.
Check for any special lighting or neon signs switched on in the vicinity.
109
Source device issue
A beeping sound is heard when my PC is booting.
If a beeping sound is heard when your PC is booting, have your PC serviced.
Other issue
The product smells like plastic.
The plastic smell is normal and disappears over time.
The monitor appears tilted.
Remove and then attach the stand again to the product.
Audio or video cuts out intermittently.
Small particles are found on the edges of the product.
When I try to change the PC resolution, a message "The
defined resolution is not supported." appears.
Check the cable connection and connect it again if required.
Use a standard cable.
The particles are part of the product design. The product is not defective.
The message "The defined resolution is not supported." appears if the input source resolution
exceeds the maximum resolution of the display.
To resolve the issue, change the PC resolution to a resolution supported on the display.
There is no sound from the speakers in HDMI mode when a
DVI-HDMI cable is connected.
DVI cables do not transmit sound data.
HDMI Black Level is not functioning properly on an HDMI
device with YCbCr output.
This function is available only when a source device, such as a DVD player and STB, is connected
to the product via an HDMI (RGB signal) cable.
Make sure to connect the audio cable to the correct input jack to enable audio.
Displayed picture colours may not look normal. Video or sound may not be available. This can
occur if a source device that only supports an older version of the HDMI standard is connected
to the product.
There is no sound in HDMI mode.
If these issues occur, connect an audio cable along with the HDMI cable.
Some PC graphics cards may not automatically recognise HDMI signals that do not include
sound. In this case, manually select a sound input.
110
Other issue
To use several external devices compatible with the HDMI-CEC feature that are connected to
the HDMI IN ports on the product, turn off the HDMI-CEC features on all the external devices.
External devices include Blu-ray and DVD players.
HDMI-CEC does not work.
Operating an external device when its HDMI-CEC feature is enabled may automatically stop
other external devices.
To change HDMI-CEC settings, refer to the device user guide or contact the device manufacturer
for assistance.
In power-saving mode, when the input source is
DisplayPort, PC display settings cannot be saved.
Go to System → Power Control and set Max. Power Saving to Off. Alternatively, configure the PC
display output settings again. Ensure the set is turned on.
When booting the PC with the input source set to
DisplayPort, the BIOS and booting screens do not appear.
Boot the PC when the set is turned on or when the input source is not DisplayPort.
111
Q&A
"" Refer to the user manual for your
PC or graphics card for further
instructions on adjustment.
Question
Answer
Set the frequency on your graphics card.
•• Windows 7: Go to Control Panel → Appearance and Personalization → Display → Adjust
resolution → Advanced Settings → Monitor and adjust the frequency in Monitor Settings.
How can I change the frequency?
•• Windows 8: Go to Settings → Control Panel → Appearance and Personalization → Display
→ Adjust resolution → Advanced Settings → Monitor and adjust the frequency in Monitor
Settings.
•• Windows 10: Go to Settings → System → Display → Advanced display settings → Display
adapter properties → Monitor, and adjust Screen refresh rate under Monitor settings.
•• Windows 7: Go to Control Panel → Appearance and Personalization → Display → Adjust
Resolution and adjust the resolution.
How can I change the resolution?
•• Windows 8: Go to Settings → Control Panel → Appearance and Personalization → Display →
Adjust Resolution and adjust the resolution.
•• Windows 10: Go to Settings → System → Display → Advanced display settings, and adjust
the resolution.
•• Windows 7: Set power-saving mode in Control Panel → Appearance and Personalization →
Personalize → Screen Saver Settings or BIOS SETUP on the PC.
How do I set powersaving mode?
•• Windows 8: Set power-saving mode in Settings → Control Panel → Appearance and
Personalization → Personalize → Screen Saver Settings or BIOS SETUP on the PC.
•• Windows 10: Set power-saving mode in Settings → Personalization → Lock screen → Screen
timeout settings → Power & sleep or BIOS SETUP on the PC.
112
Chapter 13
Specifications
General
Model Name
Panel
QB43N / QM43N
QB49N / QM49N
QB55N / QM55N
Size
43 CLASS (42.5 inches / 107.9 cm)
49 CLASS (48.5 inches / 123.2 cm)
55 CLASS (54.6 inches / 138.7 cm)
Display area
941.184 mm (H) x 529.416 mm (V)
37.1 inches (H) x 20.8 inches (V)
1073.78 mm (H) x 604.0 mm (V)
42.3 inches (H) x 23.8 inches (V)
1209.6 mm (H) x 680.4 mm (V)
47.6 inches (H) x 26.8 inches (V)
Model Name
Panel
QB65N / QM65N
QB75N / QM75N
Size
65 CLASS (64.5 inches / 163.9 cm)
75 CLASS (74.5 inches / 189.3 cm)
Display area
1428.48 mm (H) x 803.52 mm (V)
56.2 inches (H) x 31.6 inches (V)
1650.24 mm (H) x 928.26 mm (V)
65.0 inches (H) x 36.5 inches (V)
AC100-240V~ 50/60Hz
Refer to the label at the back of the product as the standard voltage can vary in different countries.
Power Supply
Operating
Temperature: 0 °C – 40 °C (32 °F – 104 °F)
* For installing the housing, keep the internal temperature at 40 °C or below.
Humidity: 10% – 80%, non-condensing
Storage
Temperature: -20 °C – 45 °C (-4 °F – 113 °F)
Humidity: 5% – 95%, non-condensing
* Applicable before the product package is unpacked.
Environmental
considerations
113
"" Plug-and-Play
This monitor can be installed and used with any Plug-and-Play compatible systems. Two-way data exchange between the monitor and PC system
optimises the monitor settings. Monitor installation takes place automatically. However, you can customise the installation settings if desired.
"" Due to the nature of the manufacturing of this product, approximately 1 pixel per million (1ppm) may appear brighter or darker on the panel. This does
not affect product performance.
"" This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate
measures.
"" For detailed device specifications, visit the Samsung Electronics website.
114
Preset Timing Modes
"" This product can be set to only one resolution for each screen size to obtain the optimum picture quality due to the nature of the panel. Using a
resolution other than the specified resolution may degrade the picture quality. To avoid this, it is recommended that you select the optimum resolution
specified for your product.
"" Horizontal Frequency
The time required to scan a single
line from the left to the right side
of the screen is called a horizontal
cycle. The reciprocal number of a
horizontal cycle is called horizontal
frequency. Horizontal frequency is
measured in kHz.
"" Vertical Frequency
The product displays a single image
multiple times per second (like a
fluorescent light) to display what
the viewer sees. The rate of a single
image being displayed repeatedly per
second is called vertical frequency
or refresh rate. Vertical frequency is
measured in Hz.
Model Name
Horizontal Frequency
QB43N / QB49N / QB55N / QB65N / QB75N
QM43N / QM49N / QM55N / QM65N / QM75N
30 - 81 kHz (DVI), 30 - 90 kHz (HDMI)
30 - 81 kHz (DVI), 30 - 90 kHz (HDMI), 30 - 134 kHz
(DisplayPort)
48 - 75 Hz (DVI), 24 - 75 Hz (HDMI)
48 - 75 Hz (DVI), 24 - 75 Hz (HDMI), 56 - 75 Hz
(DisplayPort)
Synchronization
Vertical Frequency
Optimum resolution
Resolution
Maximum resolution
1920 × 1080 @ 60 Hz (DVI)
3840 × 2160 @ 60 Hz (HDMI)
1920 × 1080 @ 60 Hz (DVI)
3840 × 2160 @ 60 Hz (HDMI)
3840 × 2160 @ 60 Hz (DisplayPort)
The screen will automatically be adjusted if a signal that belongs to the following standard signal modes is transmitted from your PC. If the signal
transmitted from the PC does not belong to the standard signal modes, the screen may be blank with the power indicator on. In such a case, change the
settings according to the following table by referring to the graphics card user manual.
115
Resolution
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
Resolution
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
IBM, 640 x 480
31.469
59.940
25.175
-/-
VESA, 1440 x 900
55.935
59.887
106.500
-/+
IBM, 720 x 400
31.469
70.087
28.322
-/+
VESA, 1600 x 900
60.000
60.000
108.000
+/+
MAC, 640 x 480
35.000
66.667
30.240
-/-
VESA, 1680 x 1050
65.290
59.954
146.250
-/+
MAC, 832 x 624
49.726
74.551
57.284
-/-
VESA, 1920 x 1080
67.500
60.000
148.500
+/+
MAC, 1152 x 870
68.681
75.062
100.000
-/-
VESA, 2560 x 1440
88.787
59.951
241.500
+/-
VESA, 640 x 480
31.469
59.940
25.175
-/-
67.500
60.000
148.500
+/+
VESA, 640 x 480
37.861
72.809
31.500
-/-
CEA, 3840 x 2160
(HDMI)
VESA, 640 x 480
37.500
75.000
31.500
-/-
VESA, 3840 x 2160
(DP)
133.313
59.997
533.250
+/-
VESA, 800 x 600
35.156
56.250
36.000
+/+
VESA, 800 x 600
37.879
60.317
40.000
+/+
VESA, 800 x 600
48.077
72.188
50.000
+/+
VESA, 800 x 600
46.875
75.000
49.500
+/+
VESA, 1024 x 768
48.363
60.004
65.000
-/-
VESA, 1024 x 768
56.476
70.069
75.000
-/-
VESA, 1024 x 768
60.023
75.029
78.750
+/+
VESA, 1152 x 864
67.500
75.000
108.000
+/+
VESA, 1280 x 720
45.000
60.000
74.250
+/+
VESA, 1280 x 800
49.702
59.810
83.500
-/+
VESA, 1280 x 1024
63.981
60.020
108.000
+/+
VESA, 1280 x 1024
79.976
75.025
135.000
+/+
VESA, 1366 x 768
47.712
59.790
85.500
+/+
116
Chapter 14
Appendix
Responsibility for the Pay Service (Cost to
Customers)
"" When the service is requested, in spite of in warranty, we may charge you for a visit from a
service technician in the following cases.
Not a product defect
Cleaning of the product, Adjustment, Explanation, Re-installation and etc.
•• If a service technician is requested to give instructions on how to use product or simply
adjusts options without disassembling product.
•• If a defect is caused by external environmental factors (Internet, Antenna, Wired Signal,
etc.)
•• If a product is reinstalled or devices are connected additionally after installing the
purchased product for the first time.
•• If a product is reinstalled to move to a different spot or to move to a different house.
•• If the customer requests instructions on how to use another company's product.
•• If customer requests instructions on how to use the network or another company's
programme.
A Product damage caused by customer's fault
Product damage caused by customer's mishandling or wrong repair
If a product damage is caused by;
•• External impact or drop.
•• Use of supplies or separatly sold product unspecified by Samsung.
•• Repair from a person besides an engineer of outsourcing service company or partner of
Samsung Electronics Co., Ltd.
•• Remodeling or repairing the product by customer.
•• Using it with incorrect voltage or non-authorised electrical connections.
•• Not following the "cautions" in User Manual.
Others
•• If product fails by natural disaster. (lightning, fire, earthquake, flood damage, etc)
•• If consumable components are all used up. (Battery, Toner, Fluorescent lights, Head,
Vibrator, Lamp, Filter, Ribbon, etc.)
"" If customer requests a service in case the product has no defect, service fee may be
charged. So please read User Manual first.
•• If customer requests software installation and setup for the product.
•• If a service technician removes/cleans dusts or foreign materials inside of the product.
•• If customer requests an installation additionally after purchasing a product through homeshopping or online.
117
Prevention of Afterimage Burn-in
What is afterimage burn-in?
Afterimage burn-in should not occur when the panel is operating normally. Normal operation
refers to a continuously changing video pattern. If the panel displays a fixed pattern for an
extended period of time a slight voltage difference may occur between the electrodes in pixels
that control the liquid crystals.
Such a voltage difference between electrodes increases with time and makes the liquid crystals
thinner. When this occurs, a previous image can remain on the screen when the pattern changes.
This information is a guide to prevent afterimage burn-in. Viewing a fixed screen
for an extended period of time may cause afterimage burn-in. This problem is not
included in warranty.
Recommended prevention practices
Viewing a fixed screen for an extended period of time may cause afterimage burn-ins or
smudges. If the product is not to be used for a long time, turn it off, or activate the Power Saving
mode or Screen Saver with a moving image.
•• Change the colours regularly.
Type 1
Type 2
FLIGHT
TIME
FLIGHT
TIME
SAMSUNG
20:30
SAMSUNG
20:30
SAMSUNG
21:10
SAMSUNG
21:10
•• Avoid combinations of a text colour and background colour of contrasting brightness.
"" Avoid using colours of contrasting brightness (black and white; grey and black).
FLIGHT : TIME
SAMSUNG : 20:30
FLIGHT : TIME
SAMSUNG : 20:30
118
Licence
Manufactured under license from Dolby Laboratories.
Dolby, Dolby Audio, Pro Logic, and the double-D symbol are
trademarks of Dolby Laboratories.
The terms HDMI and HDMI High-Definition Multimedia Interface, and
the HDMI Logo are trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other countries.
Open Source Licence Notice
In the case of using open source software, Open Source Licences are available on the
product menu. Open Source Licence Notice is written only English.
For information on the Open Source Licence Notice, contact the Samsung Customer Centre
or send email to oss.request@samsung.com.
THIS PRODUCT IS SOLD WITH A LIMITED LICENCE AND IS AUTHORISED TO BE USED
ONLY IN CONNECTION WITH HEVC CONTENT THAT MEETS EACH OF THE THREE
FOLLOWING QUALIFICATIONS: (1) HEVC CONTENT ONLY FOR PERSONAL USE; (2) HEVC
CONTENT THAT IS NOT OFFERED FOR SALE; AND (3) HEVC CONTENT THAT IS CREATED
BY THE OWNER OF THE PRODUCT.
THIS PRODUCT MAY NOT BE USED IN CONNECTION WITH HEVC ENCODED CONTENT
CREATED BY A THIRD PARTY, WHICH THE USER HAS ORDERED OR PURCHASED FROM
A THIRD PARTY, UNLESS THE USER IS SEPARATELY GRANTED RIGHTS TO USE THE
PRODUCT WITH SUCH CONTENT BY A LICENSED SELLER OF THE CONTENT.
YOUR USE OF THIS PRODUCT IN CONNECTION WITH HEVC ENCODED CONTENT IS
DEEMED ACCEPTANCE OF THE LIMITED AUTHORITY TO USE AS NOTED ABOVE.
119
Download PDF

advertising