Samsung | P50FP | Samsung Large Format Display P50FP Benutzerhandbuch

SyncMaster P50HP ,P50FP ,P63FP
PDP Monitor
User Manual
Safety Instructions
Notational
Note
These safety instructions must be followed to ensure your safety and prevent property damage.
Make sure to read the instructions carefully and use the product in the correct manner.
Warning / Caution
Failure to follow directions noted by this symbol could result in bodily
harm or damage to the equipment.
Notational Conventions
Prohibited
Important to read and understand at all times
Do not disassemble
Disconnect the plug from the
outlet
Do not touch
Ground to prevent an electric
shock
Power
When not used for extended period of time, set your computer to DPM.
If using screen saver, set it to active screen mode.
The images here are for reference only, and are not applicable in all cases
(or countries).
Shortcut to Anti-Afterimage Instructions
Do not use a damaged power cord or plug or a damaged or
loose power outlet.
•
Otherwise, this may result in electric shock or fire.
Do not touch the power plug with wet hands when removing or
plugging the plug into the outlet.
•
Otherwise, this may result in electric shock.
Make sure to connect the power cord to a grounded power outlet.
•
Otherwise, it may result in electric shock or personal injury.
Safety Instructions
Ensure that the power plug is plugged into the power outlet
firmly and correctly.
•
Otherwise, this may result in fire.
Do not forcefully bend or pull the power plug and do not place
any heavy material on it.
•
Otherwise, this may result in fire.
Do not connect multiple appliances to the same power outlet.
•
Otherwise, this may cause fire due to overheating.
Do not disconnect the power cord while using the product.
•
Otherwise, this may result in damage to the product due to
electric shock.
To disconnect the apparatus from the mains, the plug must be
pulled out from the mains socket, therefore the mains plug shall
be readily operable.
•
This may cause electric shock or fire.
Use only the power cord provided by our company. Do not use
the provided power cord of another product.
•
Otherwise, this may result in fire or electric shock.
Installation
Be sure to contact an authorized Service Center when installing your
monitor in a location with heavy dust, high or low temperatures, high humidity, and exposed to chemical substances and where it operates for 24
hours such as at airports, train stations etc.
Failure to do so may cause serious damage to your monitor.
Ensure that at least two persons lift and move the product.
•
Otherwise, it may be dropped and cause personal injury, and/
or damage the product.
When installing the product in a cabinet or rack, make sure that
the front end of the bottom of the product does not project out.
•
Otherwise, it may fall or cause personal injury.
•
Use a cabinet or rack of a size appropriate to the product.
DO NOT PLACE CANDLES, MOSQUITO REPELLANT, CIGARETTES AND ANY HEATING APPLIANCES NEAR THE
PRODUCT.
•
Otherwise, this may result in fire.
Safety Instructions
Keep heating appliances as far away from the power cord or the
product as possible.
•
Otherwise, this may result in electric shock or fire.
Do not install it in a badly ventilated location such as a bookcase
or closet.
•
Otherwise, this may result in fire due to an increase in the internal temperature.
When putting the product down, make sure to put it down softly.
•
Otherwise, this may result in damage to the screen display.
Do not place the front of the product on the floor.
•
Otherwise, this may result in damage to the screen display.
Ensure that an authorized installation company installs the wall
mount.
•
Otherwise, it may fall and cause personal injury.
•
Make sure to install the specified wall mount.
Install your product in a well ventilated location. Ensure that
there is a clearance of more than 10 cm from the wall.
•
Otherwise, it may result in fire due to an increase in the internal
temperature.
Ensure that the packaging vinyl is kept away from children.
•
Otherwise, it may result in serious harm (suffocation) if children
play with it.
If the height of your monitor is adjustable, do not place any object or part of your body on the stand when lowering it.
•
This may cause damage to the product or the person carrying
it.
Clean
When cleaning the monitor case or the surface of the PDP screen, wipe
with a slightly moistened, soft fabric.
Do not spray cleaner directly onto the surface of the product.
•
Otherwise, this may result in the discoloration and distortion of
the structure and the screen surface may peel off.
Clean the product using a soft cloth with a monitor cleaner only.
If you must use a cleaner other than the monitor cleaner, dilute it
with water at a ratio of 1:10.
Safety Instructions
When cleaning the power plug pins or dusting the power outlet,
clean it with a dry cloth.
•
Otherwise, it may result in fire.
When cleaning the product, make sure to disconnect the power
cord.
•
Otherwise, it may result in electric shock or fire.
When cleaning the product, disconnect the power cord and
clean it softly with a dry cloth.
•
(Do not use chemicals such as wax, benzene, alcohol, thinner,
mosquito repellant, lubricant, or cleaner.) These may change
the appearance of the product surface and peel off the indication labels on the product.
Since the product housing is easily scratched, make sure to use
the specified cloth only.
•
Use the specified cloth adding only a little water. As the product
may be scratched if there is any foreign material on the cloth,
make sure to shake it thoroughly before using it.
When cleaning the product, do not spray water directly onto the
main body of the product.
•
Ensure that water does not enter the product and that it is not
wet.
•
Otherwise, this may result in electric shock, fire or a malfunction.
Others
The product is a high voltage product. Ensure that users do not
disassemble, repair or modify the product themselves.
•
Otherwise, this may result in electric shock or fire. If the product
needs to be repaired, contact a Service Center.
If there is a strange smell or a strange sound or smoke is coming
from the product, disconnect the power plug immediately and contact a Service Center.
•
Otherwise, this may result in electric shock or fire.
Do not place this product in a location exposed to moisture, dust,
smoke, water, or in a car.
•
Otherwise, this may result in electric shock or fire.
When you drop the product or the case is broken, turn the power
off and disconnect the power cord. Contact a Service Center.
•
Otherwise, this may result in electric shock or fire.
Safety Instructions
If thunder or lightening is occurring, do not touch the power cord
or antenna cable.
•
Otherwise, this may result in electric shock or fire.
Do not try to move the monitor by pulling only the wire or the
signal cable.
•
Otherwise, it may fall and result in electric shock, damage to
the product or fire due to damage to the cable.
Do not lift or move the product back and forwards or right and
left while only holding the power cord or signal cables.
•
Otherwise, it may fall and result in electric shock, damage to
the product or fire due to damage to the cable.
Make sure that the ventilating opening is not blocked by a table
or curtain.
•
Otherwise, it may result in fire due to an increase in the internal
temperature.
Do not place any containers containing water, vases, flowerpots, medicines as well as any metal on the product.
•
If water or a foreign material enters the product, disconnect the
power cord and contact a Service Center.
•
This may result in a product malfunction, electric shock, or fire.
Do not use or keep combustible spray or flammable material
near the product.
•
Otherwise, this may result in an explosion or fire.
Do not insert any metal, such as chopsticks, coins, pins and
steel, or flammable objects, such as matches or paper, inside the
product (through the ventilating openings, input and output terminals, etc).
•
If water or foreign material enters the product, disconnect the
power cord and contact a Service Center.
•
Otherwise, this may result in electric shock or fire.
When using a fixed screen for a long time, an afterimage or stain
may occur.
•
If you are not using your product for a long period of time, put
it into sleep mode or use a moving screen saver.
Set a resolution and frequency appropriate to the product.
•
Otherwise, your eyesight may be damaged.
When using headphones or earphones, do not turn the volume
too high.
•
Having the sound too loud may damage your hearing.
Safety Instructions
If you continually move closer to the product screen, your eyesight may be failing.
Take a rest for at least five (5) minutes after using the monitor
for one (1) hour.
This reduces the weariness of your eyes.
Do not install it in an unstable location such as an unstable rack
or uneven surface or a location exposed to vibrations.
•
Otherwise, it may fall and cause personal injury and/or damage
the product.
•
If you use the product in a location exposed to vibrations, it may
damage the product and result in fire.
When moving the product, turn the power off and disconnect
the power plug, antenna cable, and all the cables connected to the
product.
•
Otherwise, it may result in electric shock or fire.
Ensure that children do not hang onto the product or climb up
onto the product.
•
The product may fall and cause personal injury or death.
If you do not use the product for a long period of time, disconnect
the power cord from the power outlet.
•
Otherwise, this may result in overheating or fire due to dust,
and may result in fire due to electric shock or leakage.
Do not place any heavy items or toys or confectionery, such as
cookies etc. that may attract the attention of children and to the
product.
•
Your children may hang onto the product causing it to fall and
this may result in personal injury or death.
Be careful that children do not place the battery in their mouths
when removed from the remote control. Place the battery in a location that children or infants cannot reach.
•
If children have had the battery in their mouths, consult your
doctor immediately.
When replacing the battery, insert it with right polarity (+, -).
•
Otherwise, the battery may become damaged or it may cause
fire, personal injury or damage due to leakage of the internal
liquid.
Use only the specified standardized batteries, and do not use a
new battery and a used battery at the same time.
•
Otherwise, the batteries may be damaged or cause fire, personal injury or damage due to a leakage of the internal liquid.
Safety Instructions
The batteries (and rechargeable batteries) are not ordinary refuse and must be returned for recycling purposes. The customer
is responsible for returning the used or rechargeable batteries for
recycling.
•
The customer can return used or rechargeable batteries to a
nearby public recycling center or to a store selling the same
type of the battery or rechargeable battery.
Do not place the product in a location exposed to direct sunlight
or near any heat such as a fire or heater.
•
This may reduce the lifetime of the product, and may result in
fire.
Do not drop any objects onto the product or cause any impact
to the product.
•
Otherwise, this may result in electric shock or fire.
Do not use a humidifier or kitchen table near the product.
•
Otherwise, this may result in electric shock or fire.
When there is a gas leak, do not touch the product or the power
plug but ventilate immediately.
•
If a spark occurs, it may cause an explosion or fire.
If the product has been turned on for a long time, the display
panel becomes hot. Do not touch it.
•
Keep the small accessories in a location out of the reach of
children.
Be careful when adjusting the angle of the product or the height
of the stand.
•
This may result in personal injury as your hand or fingers may
become caught.
•
Also, if you tilt the product too far, it may fall and cause personal
injury.
Do not install the product in a location low enough for children
to reach.
•
Otherwise, it may fall and result in personal injury.
•
Since the front part of the product is heavy, install the product
on a level and stable surface.
Do not put any heavy objects on the product.
•
This may result in personal injury and/or damage to the product.
Introduction
Package Contents
Note
Please make sure the following items are included with your PDP Display.
If any items are missing, contact your dealer.
Contact a local dealer to buy optional items.
Checking the Contents of the Package
Remove the lock from the package box, as shown in the figure above.
Lift up the package box by Check the contents of the Remove the Styrofoam
holding the grooves on
package.
and vinyl cover.
both sides of the package
box.
Note
•
After unpacking the package, make sure to check the contents of the package.
•
Make sure to keep the package box for transporting the product in the future.
Unpacking
Introduction
PDP Display
Manuals
Quick Setup Guide
Warranty Card
User's Guide
(Not available in all locations)
Cables
Power Cord
Others
Remote Control
Batteries (AAA X 2)
(Not available in all locations)
Ferrite Core for Power
Cord
Sold separately
D-Sub Cable
DVI Cable
Wall Mount KIT
Semi Stand KIT
BNC Cable
BNC to RCA Adaptor Jack
(Applicable to the P50HP,
P50FP model only)
To prevent injury, this apparatus must be securely attached to the wall in accordance with the installation
instructions.
Ferrite Core (Power Cord)
Introduction
•
The ferrite cores are used to shield the cables from interference.
•
When connecting a cable, open the ferrite core and clip it
around the cable near the plug.
Your PDP Display
Front
SOURCE button [SOURCE]
Switches from PC mode to Video mode. Changing the source is only allowed for external devices that are connected to the PDP Display at the
time.
[PC] → [DVI] → [AV] → [HDMI] → [Component] → [BNC]
Enter button [ ]
Activates a highlighted menu item.
MENU button [MENU]
Opens the on-screen menu and exits from the menu. Also use to exit the
OSD menu or return to the previous menu.
- VOL+
Moves from one menu item to another horizontally or adjusts selected
menu values. When OSD is not on the screen, push the button to adjust
volume.
SEL
Moves from one menu item to another vertically or adjusts selected menu
values.
/ When OSD is not on the screen, push the button to adjust channel.
Introduction
Power button [
]
Use this button for turning the PDP Display on and off.
Power indicator
Shows PowerSaver mode by blinking green
Note
See PowerSaver described in the manual for further information regarding
power saving functions. For energy conservation, turn your PDP Display
OFF when it is not needed or when leaving it unattended for long periods.
Remote Control Sensor
Aim the remote control towards this spot on the PDP Display.
Rear
Note
For detailed information concerning cable connections, refer to Connecting Cables under
Setup. The PDP Display 's configuration at the back may vary slightly depending on the PDP
Display model.
POWER IN
The power cord plugs into the PDP Display
and the wall plug.
Introduction
RS232C OUT/IN (RS232C Serial PORT)
MDC(Multiple Display Control) Program Port
RGB IN (PC Video Connection Terminal)
Using a D-Sub Cable (15 pin D-Sub) - PC
mode (Analog PC)
DVI IN (PC Video Connection Terminal)
Using a DVI Cable (DVI-D to DVI-D) - DVI
mode (Digital PC)
DVI / PC / HDMI IN [DVI/PC/HDMI AUDIO IN] (PC/DVI/HDMI Audio Connection
Terminal (Input))
- R]
AV / COMPONENT AUDIO IN [L- AUDIO
Connect the port of the DVD, VCR (DVD /
DTV Set-Top Box) to the [ L- AUDIO - R ] port
of the PDP Display.
AV IN [VIDEO]
Connect the [ VIDEO ] terminal of your monitor to the video output terminal of the external device using a VIDEO cable.
AUDIO OUT
Headphone output terminal.
DVI OUT
Connect a monitor to another monitor
through a DVI cable.
Can connect up to 10 PDP display units.
HDMI IN
Connect the HDMI terminal at the back of
your PDP Display to the HDMI terminal of
your digital output device using a HDMI cable.
Introduction
BNC OUT [R/PR, G/Y, B/PB, H, V]
(BNC Terminal (Output))
BNC (Analog PC) Connection: connecting
the R, G, B, H, V ports.
BNC/COMPONENT IN[R/PR, G/Y, B/
PB, H, V]
(BNC/Component Connection Terminal (Input))
Kensington Lock
The Kensington Lock is a device used to
physically fix the system when using it in a
public place. The locking device has to be
purchased separately. The appearance and
locking method may differ from the illustration depending on the manufacturer. Refer to
the manual provided with the Kensington
Lock for proper use. The locking device has
to be purchased separately.
Note
The location of the Kensington Lock may be
different depending on its model.
Using the Anti-Theft Kensington Lock
1.
Insert the locking device into the Kenand turn
sington slot on the Monitor
it in the locking direction
.
2.
Connect the Kensington Lock cable.
3.
Fix the Kensington Lock to a desk or a
heavy stationary object.
Note
See Connecting Cables for further information regarding cable connections.
Remote Control
Note
The performance of the remote control may be affected by a TV or other electronic device
operating near the PDP Display , causing a malfunction due to interference with the frequency.
Introduction
POWER
OFF
Number Buttons
DEL
button
+ VOL MUTE
TV/DTV
MENU
INFO
Color Buttons
TTX/MIX
STILL
AUTO
S.MODE
MDC
LOCK
SOURCE
ENTER/PRE-CH
CH/P
D.MENU
GUIDE
RETURN
Up-Down Left-Right buttons
EXIT
SRS
MagicInfo
P.MODE
DUAL/MTS
PIP
SWAP
1.
POWER
Turns the product On.
2.
Off
Turns the product Off.
3. Number Buttons
4. DEL
button
Press to change the channel.
The "-" button operates only for DTV. It is used to select
MMS (multi-channel) for a DTV.
Introduction
5. + VOL -
Adjusts the audio volume.
6.
Pauses (mutes) the audio output temporarily. This is displayed on the lower left corner of the screen. The audio
resumes if MUTE or - VOL + is pressed in the Mute mode.
MUTE
7. TV/DTV
8.
Selects the TV and DTV mode directly.
MENU
Activates a highlighted menu item.
9.
10.
Opens the on-screen menu and exits from the menu or
closes the adjustment menu.
INFO
11. Color Buttons
TTX/MIX
12.
Current picture information is displayed on the upper left
corner of the screen.
Press to add or delete channels and to store channels to the
favorite channel list in the “Channel List” menu.
TV channels provide written information services via teletext.
- Teletext Buttons
For more information > TTX / MIX
13. STILL
Press the button once to freeze the screen. Press it again
to unfreeze.
14. AUTO
Adjusts the screen display automatically in PC mode. By
changing the resolution in the control panel, auto function is
performed.
15. S.MODE
When pressing this button, the current mode is displayed at
the bottom centre of the screen. The PDP Display has a
built-in high fidelity stereo amplifier. Then press the button
again to circle through available preconfigured modes.
( Standard → Music → Movie → Speech → Custom )
16. MDC
MDC Quick Launch Button.
17. LOCK
Activates or deactivates all function keys on both the remote
control and the PDP Display except for the Power and LOCK
buttons.
18.
SOURCE
Press the button to change the input signal SOURCE.
Changing the SOURCE is only allowed for external devices
that are connected to the monitor at the time.
19.
20.
ENTER/PRE-CH
CH/P
This button is used to return to the immediately previous
channel.
In TV mode, selects TV channels.
21. D.MENU
DTV menu display
22. GUIDE
Electronic Program Guide (EPG) display.
Introduction
23.
RETURN
Returns to the previous menu.
24. Up-Down Left-Right buttons
Moves from one menu item to another horizontally, vertically
or adjusts selected menu values.
25.
Exits from the menu screen.
EXIT
26.
SRS
Selects SRS TruSurround XT mode.
27. MagicInfo
MagicInfo Quick Launch Button.
28. P.MODE
When you press this button, current picture mode is displayed on the lower center of the screen.
AV / HDMI / TV : P.MODE
The PDP Display has four automatic picture settings that
are preset at the factory. Then push button again to circle
through available preconfigured modes. ( Dynamic →
Standard → Movie → Custom )
PC / DVI / MagicInfo: M/B (MagicBright)
MagicBright is a feature providing the optimum viewing environment depending on the contents of the image you are
watching. Then push button again to circle through available
preconfigured modes. (Entertain → Internet → Text → Custom )
29.
DUAL/MTS
DUALSTEREO/MONO, DUAL l / DUAL ll and MONO/NICAM
MONO/NICAM STEREO can be operated depending on the
broadcasting type by using the DUAL button on the remote
control while watching TV.
MTSYou can select MTS (Multichannel Television Stereo) mode.
FM Stereo
30. PIP
Audio Type
MTS/S_Mode
Default
Mono
Mono
Stereo
Mono ↔ Stereo
Manual
Change
SAP
Mono ↔ SAP
Mono
Every time you press the button, a PIP screen appears.
- This fuction does not work for this PDP Display.
31. SWAP
Swaps the contents of the PIP and main image. The image
in the PIP window will appear on the main screen, and the
main screen image will appear in the PIP window.
- This fuction does not work for this PDP Display.
Introduction
Mechanical Layout (P50HP, P50FP)
Mechanical Layout
PDP Display Head
Introduction
Installation VESA Bracket
•
When installing VESA, make sure to comply with the international VESA standards.
•
Purchasing VESA Bracket and Installation Information : Please contact your nearest
SAMSUNG Distributor to place an order. After your order is placed, installation professionals will visit you and install the bracket.
•
At least 2 persons are needed in order to move the PDP Display.
•
SAMSUNG is not responsible for any product damage or any injury caused by installation
at customer's discretion.
Dimensions
Notice
For securing the bracket on a wall, use only machine screws of 6 mm diameter and 8 to 12
mm length.
Introduction
Wall Bracket Installation
•
Contact a technician for installing the wall bracket.
•
SAMSUNG Electronics is not responsible for any damages to the product or harm to
customers when the installation is done by the customer.
•
This product is for installing on cement walls. The product may not stay in place when
installed on plaster or wood.
Components
Only use the components and accessories shipped with the product.
Wall Bracket(1)
Hinge(Left 1, Right Plastic Screw
1)
Hanger (A)(11)
(4)
Screw
(B)(4)
Wall Bracket Assembly
Note
There are two hinges(left and right). Use the correct one.
1.
Insert and tighten the Captive Screw in the direction of the arrow.
When done, mount the wall bracket on the wall.
There are two hinges(left and right). Use the correct one.
A-
Captive Screw
B-
Wall Bracket
C-
Hinge (Left)
D-
Hinge (Right)
Anchor
(11)
Introduction
2.
Before drilling into the wall, check if the length between the two locking holes at the back
of the product is correct.
If the length is too short or long, loosen all or some of the 4screws on the wall bracket to
adjust the length.
A3.
Length between the two locking holes
Check the installation diagram and mark the drill points on the wall. Use the 5.0 mm bit
to drill holes deeper than 35 mm. Fix each anchor in the corresponding hole. Match each
of the brackets and hinge holes to the corresponding anchor holes and insert and tighten
the 11 screws A.
To mount the product on the wall bracket
The shape of the product may vary depending on the model. (The assemblies of the plastic
hanger and the screw are the same)
1.
Remove the 4 screws on the back of the product.
Introduction
2.
Insert the screw B into the plastic hanger.
Notice
•
Mount the product on the wall bracket and make sure it is properly fixed to the left
and right plastic hangers.
•
Be careful when installing the product on the bracket as fingers can be caught in the
holes.
•
Make sure the wall bracket is securely fixed to the wall, or the product may not stay
in place after installation.
3.
Tighten the 4 screws in step 2 (plastic hanger + screw B)to the rear holes of the product.
4.
Remove safety pin (3) and insert the 4 product holders into the corresponding bracket
holes (1). Then place the product(2) so that it is firmly fixed to the bracket. Make sure to
re-insert and tighten the safety pin (3) to securely hold the product to the bracket.
Introduction
A-
PDP Display
B-
Wall Bracket
C-
Wall
Wall Bracket Angle Adjustment
Adjust the bracket angle to -2° before installing it on the wall.
1.
Fix the product to the wall bracket.
2.
Hold the product at the top in the center and pull it forward (direction of the arrow) to
adjust the angle.
Note
You can adjust the bracket angle between -2° and 15°.
Make sure to use the top center, and not the left or the right side of the product to adjust the
angle.
Introduction
Mechanical Layout (P63FP)
Mechanical Layout
PDP Display Head
Wall Bracket Installation
•
Contact a technician for installing the wall bracket.
•
SAMSUNG Electronics is not responsible for any damages to the product or harm to
customers when the installation is done by the customer.
•
This product is for installing on cement walls. The product may not stay in place when
installed on plaster or wood.
Components
Only use the components and accessories shipped with the product.
Wall Bracket(1)
Hinge(Left 1, Right Plastic Screw
1)
Hanger (A)(11)
(4)
Screw
(B)(4)
Anchor
(11)
Introduction
Wall Bracket Assembly
Note
There are two hinges(left and right). Use the correct one.
1.
Insert and tighten the Captive Screw in the direction of the arrow.
When done, mount the wall bracket on the wall.
There are two hinges(left and right). Use the correct one.
2.
A-
Captive Screw
B-
Wall Bracket
C-
Hinge (Left)
D-
Hinge (Right)
Before drilling into the wall, check if the length between the two locking holes at the back
of the product is correct.
If the length is too short or long, loosen all or some of the 4screws on the wall bracket to
adjust the length.
A-
Length between the two locking holes
Introduction
3.
Check the installation diagram and mark the drill points on the wall. Use the 5.0 mm bit
to drill holes deeper than 35 mm. Fix each anchor in the corresponding hole. Match each
of the brackets and hinge holes to the corresponding anchor holes and insert and tighten
the 11 screws A.
To mount the product on the wall bracket
The shape of the product may vary depending on the model. (The assemblies of the plastic
hanger and the screw are the same)
1.
Remove the 4 screws on the back of the product.
2.
Insert the screw B into the plastic hanger.
Notice
•
Mount the product on the wall bracket and make sure it is properly fixed to the left
and right plastic hangers.
•
Be careful when installing the product on the bracket as fingers can be caught in the
holes.
•
Make sure the wall bracket is securely fixed to the wall, or the product may not stay
in place after installation.
Introduction
3.
Tighten the 4 screws in step 2 (plastic hanger + screw B)to the rear holes of the product.
4.
Remove safety pin (3) and insert the 4 product holders into the corresponding bracket
holes (1). Then place the product(2) so that it is firmly fixed to the bracket. Make sure to
re-insert and tighten the safety pin (3) to securely hold the product to the bracket.
A-
PDP Display
B-
Wall Bracket
C-
Wall
Wall Bracket Angle Adjustment
Adjust the bracket angle to -2° before installing it on the wall.
1.
Fix the product to the wall bracket.
2.
Hold the product at the top in the center and pull it forward (direction of the arrow) to
adjust the angle.
Note
You can adjust the bracket angle between -2° and 15°.
Introduction
Make sure to use the top center, and not the left or the right side of the product to adjust the
angle.
Connections
Connecting a Computer
Using a Power cord with Earth
In the event of failure, the earth lead may cause electric shock. Make
sure to wire the earth lead in correctly, before connecting the AC power.
When un-wiring the earth lead, make sure to disconnect the AC power
in advance.
•
Note
AV input devices such as DVD players, VCRs or camcorders as well as your computer can
be connected to the PDP Display. For detailed information on connecting AV input devices,
refer to the contents under Adjusting Your PDP Display.
Connect the power cord for your PDP Display to the power port on the
back of the PDP Display. Turn on the power switch.
There are 2 ways to connect the D-sub to your PDP Display. Choose one
of the following:
Using the D-sub (Analog) connector on the video card.
•
Connect the D-sub to the 15-pin, RGB port on the back of your PDP
Display and the 15 pin D-sub Port on the computer.
Using the DVI (Digital) connector on the video card.
•
Connect the DVI Cable to the DVI(HDCP) port on the back of your PDP
Display and the DVI port on the computer.
Using the BNC (Analog) connector on the video card.
Connections
•
Connect the BNC Cable to the BNC/COMPONENT IN - R, G, B, H, V
ports on the back of your PDP Display and the 15 pin D-sub Port on
the computer.
Connect the audio cable for your PDP Display to the audio port on the back
of your computer.
Note
•
Turn on both your computer and the PDP Display.
•
The DVI cable is optional.
•
Contact a local SAMSUNG Electronics Service Center to buy optional items.
Connecting to Other devices
Using a Power cord with Earth
•
In the event of failure, the earth lead may cause electric shock. Make
sure to wire the earth lead in correctly, before connecting the AC power.
When un-wiring the earth lead, make sure to disconnect the AC power
in advance.
Note
AV input devices such as DVD players, VCRs or camcorders as well as your computer can
be connected to the PDP Display. For detailed information on connecting AV input devices,
refer to the contents under Adjusting Your PDP Display.
Connecting AV Devices
1.
Connect the port of the DVD, VCR (DVD / DTV Set-Top Box) to the [R-AUDIO-L] port of
the PDP Display.
2.
Then, start the DVD, VCR or Camcorders with a DVD disc or tape inserted.
3.
Select AV using the SOURCE .
Note
The PDP Display has AV connection terminals to connect AV input devices like DVDs, VCRs
or Camcorders. You may enjoy AV signals as long as the PDP Display is turned on.
Connections
Connecting to a Camcorder
1.
Locate the AV output jacks on the camcorder. They are usually found on the side or back
of the camcorder. Connect a set of audio cables between the AUDIO OUTPUT jacks on
the camcorder and the AV/COMPONENT AUDIO IN [L-AUDIO-R] on the PDP Display.
2.
Connect a video cable between the VIDEO OUTPUT jack on the camcorder and the AV
IN [VIDEO] on the PDP Display.
3.
Select AV for the Camcorder connection using the Source button on the front of the PDP
Display or on the remote control.
4.
Then, start the Camcorders with a tape inserted.
Note
The audio-video cables shown here are usually included with a Camcorder. (If not, check
your local electronics store.) If your camcorder is stereo, you need to connect a set of two
cables.
Connecting a DVD Player
1.
Connect a set of audio cables between the AV/COMPONENT AUDIO IN [L-AUDIO-R]
on the PDP Display and the AUDIO OUT jacks on the DVD player.
2.
Connect a Component cable between the BNC / COMPONENT IN - PR, Y, PB port on
the PDP Display and the PR, Y, PB jacks on the DVD player.
Connections
Note
•
Select Component for the connection to a DVD player using the SOURCE button on the
front of the PDP Display or on the remote control.
•
Then, start the DVD Player with a DVD disc inserted.
Note
•
A component cable is optional.
For an explanation of Component video, consult your DVD manual.
Connecting a DTV Set Top Box
Note
•
The connections for a typical Set Top Box are shown below.
1.
Connect a Component cable between the BNC / COMPONENT IN - PR, Y, PB port on
the PDP Display and the PR, Y, PB jacks on the Set Top Box.
2.
Connect a set of audio cables between the AV/COMPONENT AUDIO IN [L-AUDIO-R]
on the PDP Display and the AUDIO OUT jacks on the Set Top Box.
Note
•
Select Component for the connection to a DTV Set Top Box using the SOURCE button
on the front of the PDP Display or on the remote control.
Note
•
For an explanation of Component video, see your Set Top Box owner's manual.
Connections
Connecting Using a HDMI Cable
Note
•
Input devices such as digital DVD are connected to the HDMI IN terminal of the PDP
Display using the HDMI cable.
•
You cannot connect a PC to the HDMI IN terminal.
Connecting Using a DVI Cable
Note
•
Connect the DVI output terminal of a digital output device to the DVI IN terminal of the
PDP Display using a DVI cable.
•
Set the name of DVI input to AV device in Source -> Edit Name Menu.
Connections
Connecting to an Audio System
Note
•
Connect a set of audio cables between the AUX L, R jacks on the AUDIO SYSTEM and
AUDIO OUT [L-AUDIO-R] on PDP Display.
Introduction
A Multiple Display Control (MDC) is an application allowing various displays to be easily and simultaneously
operated on a PC. RS-232C, a standard of serial communication, is used for the communication between a PC and
a display. Therefore, a serial cable should be connected between the serial port on a PC and the serial port on a
display.
Main Screen
Click Start > Program > Samsung > MDC System to start the program.
Select a set to see the volume of the selected set within the slider.
Main Icons
Select Button
Remocon
Info Grid
Safety Lock
Display Selection
Port Selection
Control Tools
1. Use the main icons to switch into each screen.
2. Allows you to enable or disable the remote control signal receiving function of the display unit.
3. Set the Safety Lock function.
When setting the Lock function, you can only operate power and lock buttons on the remote control and set.
4. The setting for the PC Serial Port can change. The original value is COM1.
5. Click Select all or Clear to select or clear all displays.
6. Use Grid to view brief information on selected display.
7. Select a display from Display Selection.
8. Use Control Tools to control displays.
<Note> The remote control Enable/Disable function operates whether or not the power is On/Off, and this
applies to all displays connected to the MDC. However, regardless of the status at the time the MDC is
shut down, the remote control signal receiving function of all displays is initialized to Enable when the
MDC is closed.
Port Selection
1. The Multiple Display Control is originally set to COM1.
2. If any port other than COM1 is used, COM1 through COM4 can be selected in the Port Selection Menu.
3. If the exact port name that is connected to the LCD Display using a serial cable is not selected, communication will
be unavailable.
4. The selected port is stored in the program and used for the next program as well.
Power Control
1. Click Power Control of the main icons and the Power Control screen appears.
Info Grid shows some basic information necessary to Power Control.
1)
(Power Status)
2) Input
3) Image Size
4) On Timer
5) Off Timer
2. Use the Select All button or Check Box to choose a display to control.
Power Control allows controlling some of the functions of the selected display.
1) Power On/Off
- Turns the power of the selected display On/Off.
2) Volume
- Controls the volume level of the selected display.
It receives the volume value of the selected display from the sets and displays it in the slider.
(When you cancel the selection or choose Select All, the value returns to the default value 10)
3)
(Mute On/Off)
- Turns on/off the Mute function of the selected display.
When selecting one set at a time, turn on the Mute function for the selected set.
The Mute function is disabled automatically when you adjust the volume level.
(The values return to the default settings when you undo the selections or choose "Select All".)
The Power Control feature is available for all displays.
The Volume Control and Mute features are available only for the displays whose power status is ON.
Input Source
1. Click Input Source of the main icons and the Input Source control screen appears.
Click Select All or use Check Box to select a display to control.
• TV Mode
• PC Mode
Info Grid shows some basic information necessary to Input Source Control.
1)
PC
- Changes the Input Source of the selected display to PC.
2)
BNC
- Changes the Input Source of the selected display to BNC.
3)
DVI
- Changes the Input Source of the selected display to DVI.
4)
TV
- Changes the Input Source of the selected display to TV.
5)
DTV
- Changes the Input Source of the selected display to DTV.
6)
AV
- Changes the Input Source of the selected display to AV.
7)
S-Video
- Changes the Input Source of the selected display to S-Video.
8)
Component
- Changes the Input Source of the selected display to Component.
9)
MagicInfo
- The Input source of MagicInfo works only on MagicInfo model.
10)
HDMI
- Changes the Input Source of the selected display to HDMI.
11)
Channel
- Channel arrow appears when the Input Source is TV.
TV Source can be selected only in products with TV and controlling channels is allowed only when
Input Source is TV.
The Input Source Control feature is available only for the displays whose power status is ON.
Image Size
PC, BNC, DVI
1. Click Image Size of the main icons and the Image Size control screen appears.
Info Grid shows some basic information necessary to Image Size Control.
1)
( Power Status)
- Shows the power status of the current display.
2) Image Size
- Shows the current Image Size of the display in use.
3) Input
- Shows the current Input Source of the display in use.
4) Info Grid displays only the displays whose Input Source is PC, BNC, DVI.
5) PC Source - When you click Image Size, the PC Source tab first appear.
- The Image Size Control button controls Image Size available for PC, BNC, DVI.
6) Video Source
- Click the Video Source tab to control Image Size for respective Input Source.
The Input source of MagicInfo works only on MagicInfo model.
The Input source of TV works only on TV model.
Image Size Control is available only for the displays for which power status is ON.
Image Size
TV, AV, S-Video, Component, DVI(HDCP), HDMI, DTV
1. Click Image Size of the main icons and the Image Size control screen appears.
Info Grid shows some basic information necessary to Image Size Control.
1) Click the Video Source tab to adjust Image Size for TV, AV, S-Video, Component, DVI(HDCP), HDMI, DTV.
Click Select All or use Check Box to select a display to control.
2) Info Grid displays only the display having TV, AV, S-Video, Component or DVI(HDCP) as input source.
3) Switch Image Size of the selected display randomly.
Note: Auto Wide, Zoom1 and Zoom2 are not available for selection when the input signal type for
Component and DVI (HDCP) is 720p or 1080i.
(The Auto Wide mode is available only for TV, AV, and S-Video.)
4) The screen modes can only be adjusted when a TV (PAL only) is connected and the Image Size item is set to Auto
Wide.
The Input source of MagicInfo works only on MagicInfo model.
The Input source of TV works only on TV model.
The Image Size Control feature is available only for the displays whose power status is ON.
Time
1. Click Time of the main icons and the Time Control screen appears.
Info Grid shows some basic information necessary to Time Control.
1) Current Time
- Set the current time for the selected display (PC Time).
- To change the current time, first change the PC Time.
2) On Time Setup
- Set the Hour, Minute, AM/PM of On Time Setup, Status, Source, Volume of the selected display.
3) Off Time Setup
- Set the Hour, Minute, and AM/PM, Status for Off Time Setup of the selected display.
4) Shows the On Time settings.
5) Shows the Off Time settings.
The Input source of MagicInfo works only on MagicInfo model.
The Input source of TV works only on TV model.
Time Control is available only for the displays for which the power status is ON.
At On Time Setup, TV Source functions only for TV Model.
At On Time Setup, MagicInfo Source functions only for MagicInfo Model.
PIP
PIP Size
1. Click PIP of the main icons and the PIP control screen appears.
Click Select All or use Check Box to select a display to control.
Info Grid shows some basic information necessary to PIP Size Control.
1) PIP Size
- Shows the current PIP Size of the display in use.
2) OFF
- Turns off the PIP of the selected display.
3) Large
- Turns on the PIP of the selected display and changes the size to Large.
4) Small
- Turns on the PIP of the selected display and changes the size to Small.
5) Double 1
- Turns on the PIP of the selected display and changes the size to Double 1.
6) Double 2
- Turns on the PIP of the selected display and changes the size to Double 2.
7) Double 3 (Picture By Picture)
- Turns on the PBP of the selected display and changes the size to Double 3.
The Input source of MagicInfo works only on MagicInfo model.
The Input source of TV works only on TV model.
PIP Size can be controlled with turning on the LCD Display power.
PIP
PIP Source
1. Click PIP of the main icons and the PIP control screen appears.
Info Grid shows some basic information necessary to PIP Source Control.
1) PIP Source
- PIP Source can be controlled with turning on the LCD Display power.
2) PC
- Changes the source of the PIP of the selected display to PC.
3) BNC
- Changes the source of the PIP of the selected display to BNC.
4) DVI
- Changes the source of the PIP of the selected display to DVI.
5) AV
- Changes the source of the PIP of the selected display to AV.
6) S-Video
- Changes the source of the PIP of the selected display to S-Video.
7) Component
- Changes the source of the PIP of the selected display to Component.
8) HDMI
- Changes the source of the PIP of the selected display to HDMI.
Note: Some of the PIP Sources may not be available for selection, depending on the input source type
of the Main Screen.
The Input source of MagicInfo works only on MagicInfo model.
The PIP Control feature is available only for the displays whose power status is ON and the PIP
function is set to ON.
Settings
Picture
1. Click Settings of the main icons and the Settings Control screen appears.
Info Grid shows some basic information necessary to Settings Control.
When each function is selected, the set value of the selected function is displayed in the slide.When selected, each
function fetches the value for the set and displays it on the slide bar. When "Select All" is chosen, the default value
is displayed. Changing a value in this screen will automatically change the mode to "CUSTOM."
1) Picture
- Available only for TV, AV, S-Video, Component, HDMI, DTV.
2) Contrast
- Adjusts Contrast of the selected display.
3) Brightness
- Adjusts Brightness of the selected display.
4) Sharpness
- Adjusts Sharpness of the selected display.
5) Color
- Adjusts Color of the selected display.
6) Tint
- Adjusts Tint of the selected display.
- Available only for NT.
7) Color Tone
- Adjusts the Color Tone for the selected display.
8) Color Temp
- Adjusts the Color Temp for the selected display.
9) Brightness Sensor
- Adjusts the Brightness Sensor for the selected display.
10) Dynamic Contrast
- Adjusts the Dynamic Contrast for the selected display.
The Input source of MagicInfo works only on MagicInfo model.
Color Temp is only enabled if the Color Tone is set to Off.
The Input source of TV works only on TV model.
This feature is available only for the displays whose power status is ON and if no selection is made, the
factory default is displayed.
Settings
Picture PC
1. Click Settings of the main icons and the Settings Control screen appears.
Info Grid shows some basic information necessary to Settings Control. When each function is selected, the set value
of the selected function is displayed in the slide. When selected, each function fetches the value for the set and
displays it on the slide bar. When "Select All" is chosen, the default value is displayed. Changing a value in this
screen will automatically change the mode to "CUSTOM."
1) Picture PC
- Available only for PC, BNC, DVI.
2) Contrast
- Adjusts Contrast of the selected display.
3) Brightness
- Adjusts Brightness for the selected display.
4) Red
- Adjusts red Color of the selected display.
- Available only for NT.
5) Green
- Adjusts green Color of the selected display.
- Available only for NT.
6) Blue
- Adjusts blue Color of the selected display.
- Available only for NT.
7) Color Tone
- Adjusts the Color Tone for the selected display.
8) Color Temp
- Adjusts the Color Temp for the selected display.
9) Brightness Sensor
- Adjusts the Brightness Sensor for the selected display.
10) Dynamic Contrast
- Adjusts the Dynamic Contrast for the selected display.
The Input source of MagicInfo works only on MagicInfo model.
The Input source of TV works only on TV model.
Color Temp is only enabled if the Color Tone is set to Off.
This feature is available only for the displays whose power status is ON and if no selection is made, the
factory default is displayed.
Settings
Audio
1. Click Settings of the main icons and the Settings Control screen appears.
Info Grid shows some basic information necessary to Settings Control. When each function is selected, the set value
of the selected function is displayed in the slide. When selected, each function fetches the value for the set and
displays it on the slide bar. When "Select All" is chosen, the default value is displayed. Changing a value in this
screen will automatically change the mode to "CUSTOM."
1) Audio
- Controls audio settings for all input sources.
2) Bass
- Adjusts Bass of the selected display.
3) Treble
- Adjusts Treble of the selected display.
4) Balance
- Adjusts Balance of the selected display.
5) SRS TS XT
- SRS TS XT Sound ON/OFF of the selected display.
6) Sound Select
- Select either Main or Sub when PIP is On.
The Input source of MagicInfo works only on MagicInfo model.
The Input source of TV works only on TV model.
This feature is available only for the displays whose power status is ON and if no selection is made, the
factory default is displayed.
Settings
Image Lock
1. Click Settings of the main icons and the Settings Control screen appears.
Info Grid shows some basic information necessary to Settings Control.
1) Image Lock
- Available only for PC, BNC.
2) Coarse
- Adjusts Coarse of the selected display.
3) Fine
- Adjusts Fine of the selected display.
4) Position
- Adjusts Position of the selected display.
5) Auto Adjustment
- Self-Adjust to the incoming PC signal.
The Input source of MagicInfo works only on MagicInfo model.
The Input source of TV works only on TV model.
Settings Control is available only for the displays for which the power status is ON.
Maintenance
Lamp Control
1. Click on the "Maintenance" icon in the Main Icon column to display the Maintenance screen.
An "Info Grid" showing several basic data items appears.
1) Maintenance
- Allows the Maintenance Control function for all input sources.
2) Auto Lamp Control
- Automatically adjusts the backlight of the selected display at a specified time.
The Manual Lamp Control automatically turns off if you adjust using the Auto Lamp Control.
3) Manual Lamp Control
- Allows you to adjust the backlight of the selected display regardless of the time.
The Auto Lamp Control automatically turns off if you adjust using the Manual Lamp Control.
The Maintenance Control feature is available only for the displays whose power status is ON.
The Input source of MagicInfo works only on MagicInfo model.
The Input source of TV works only on TV model.
Maintenance
Scroll
1. Click on the "Maintenance" icon in the Main Icon column to display the Maintenance screen.
1) Scroll
- This function is used to remove the afterimages that occur when a still screen is displayed on the selected
display
for a long time.
2) Pixel Shift
- This allows the screen to be moved finely at the specified time interval.
3) Safety Screen
- The Safety Screen function is used to prevent afterimages from occurring when a still screen is displayed on the
monitor for a long time. The Interval item is used to set the repetition cycle in hour units and the Time item is
used to set the time when the Safety Screen function must be performed.
The Type item can be set to Scroll, Pixel, Bar, Eraser, All White, or Pattern.
4) Safety Screen2
- This function is used to prevent afterimages from occurring. There are five (5) types that you can select and
control with this function.
For the Scroll type, the Time item can be set to 1, 2, 3, 4 or 5. For the Bar and Eraser types, it can be set
to 10, 20, 30, 40 or 50. For the All White and Pattern type, it can be set to 1, 5, 10, 20 or 30.
The Input source of MagicInfo works only on MagicInfo model.
The Input source of TV works only on TV model.
The Maintenance Control feature is available only for the displays whose power status is ON.
Maintenance
Video Wall
1. Click on the "Maintenance" icon in the Main Icon column to display the Maintenance screen.
1) Video Wall
- A Video Wall is a set of video screens that are connected together, so that each screen shows a part of the whole
picture or so that the same picture is repeated on each screen.
2) Video Wall (Screen divider)
- The screen can be divided into.
You can select a number of screens with a different layout when dividing.
z Select a mode from Screen divider.
z Select a display from Display Selection.
z The place will be set up by pressing a number in the selected mode.
z The MDC program supplied by Samsung supports up to 5x5 LCD Displayes.
3) On / Off
- Turns on/off the Video Wall function of the selected display.
4) Format
- The format can be selected to see a divided screen.
z
Full
z
Natural
You may not operate this function in MagicInfo.
The Input source of TV works only on TV model.
The Maintenance Control function is available only for the displays where the power status is ON.
Troubleshooting
1. The display you wish to control does not appear on the Power Control Info Grid
- Check the connection of RS232C. (Check if it is properly connected to the Com1 port)
- Check the displays to see if any of the other displays connected have the same ID. If more than one displays have
the same ID, those displays are not properly detected by the program due to data conflict.
- Check if the Display Set ID is a number between 0 and 25. (Adjust using the Display menu)
Note :
A Display Set ID must be a value between 0 and 25 .
2. The display you wish to control does not appear on the other Control Info Grids
- Check to see if the display power is ON. (You can check this in Power Control Info Grid)
- Check if you can change the input source of the display.
3. The dialogue box appears repeatedly.
- Check to see if the display you wish to control is selected.
4. Both On Timer and Off Timer have been set but different time is showing.
- Apply current time to synchronize the display clocks.
5. The remote may not function properly when you turn off the remote Function, disconnect the RS-232C cable, or exit
the program in an Irregular manner. Rerun the program and turn the remote function again to Restore normal
functions.
<Note> This program may malfunction due to problems in communication circuits or interference from electronic
appliances nearby.
Settings Value Display In Multiple Display Mode
When there are more than one displays connected, the settings values are displayed as follows.
1. No selection: Displays the Factory Default Value.
2. Selected one display: Fetches and displays the settings value for the selected display.
3. Selected one display (ID1) and add another display (ID3): The program, which was displaying the settings value of
ID 1, fetches and displays the value of ID3.
4. Selected all sets using Select All: Returns to the Factory Default Value.
Adjusting the PDP Display
Input
Available Modes
•
PC / DVI / BNC
•
AV
•
HDMI
•
Component
Source List
MENU → ENTER → [Input] → ENTER → [Source List] →
,
→ ENTER
Use to select PC, DVI or other external input sources connected to the PDP Display. Use to
select the screen of your choice.
1.
PC
2.
DVI
3.
AV
4.
HDMI
5.
Component
6.
BNC
Note
•
The direct button on the remote control is the 'SOURCE' button.
Edit Name
MENU → ENTER → [Input] →
→ ENTER → [Edit Name] →
,
→ ENTER
Adjusting the PDP Display
Name the input device connected to the input jacks to make your input source selection
easier.
VCR / DVD / Cable STB / HD STB / Satellite STB / AV Receiver / DVD Receiver / Game /
Camcorder / DVD Combo / DHR / PC
Note
•
When connecting a PC to the HDMI or DVI terminal, set Edit Name to PC.
•
In other cases, set Edit Name to AV.
•
However, since 640x480, 720P (1280x720), and 1080p (1920x1080) are common signals
for AV and PC, make sure to set the Edit Name in accordance with the input signal.
•
The Picture menu changes depending on the input signal and Edit Name.
Picture [PC / DVI/ BNC]
Available Modes
•
PC / DVI / BNC
•
AV
•
Component
MagicBright
MENU →
→ ENTER → [Picture] → ENTER → [MagicBright] →
,
→ ENTER
MagicBright is a new feature providing the optimum viewing environment depending on the
contents of the image you are watching. Currently four different modes are available: Entertain, Internet, Text and Custom. Each mode has its own pre-configured brightness value. You
can easily select one of the four settings by simply pressing the MagicBright control button.
1.
Entertain
High brightness
Adjusting the PDP Display
For watching motion pictures such as a DVD or VCR.
2.
Internet
Medium brightness
For working with a mixture of images such as texts and graphics.
3.
Text
Normal brightness
For documents or works involving heavy text.
4.
Custom
Although the values are carefully chosen by our engineers, the pre-configured values
may not be comfortable to your eyes depending on your taste.
If this is the case, adjust the brightness and contrast by using the OSD menu.
Custom
By using the on-screen menus, the contrast and brightness can be changed to your personal
preference.
MENU →
→ ENTER → [Picture] →
→ ENTER → [Custom]
Note
By adjusting the picture using the Custom function, MagicBright will change to Custom mode.
Contrast
MENU → → ENTER → [Picture] →
, → ENTER
→ ENTER → [Custom] → ENTER→ [Contrast] →
Adjusts the Contrast.
Brightness
MENU → → ENTER → [Picture] →
ness] → , → ENTER
→ ENTER → [Custom] →
→ ENTER→ [Bright-
Adjusts the Brightness.
Sharpness
MENU → → ENTER → [Picture] →
[Sharpness] → , → ENTER
Adjusts the Sharpness.
→ ENTER → [Custom] →
→
→ ENTER →
Adjusting the PDP Display
Color Tone
MENU →
→ ENTER → [Picture] →
→
→ENTER → [Color Tone] →
,
→ ENTER
The color tones can be changed.
1.
Off
2.
Cool
3.
Normal
4.
Warm
5.
Custom
Note
If you set the Color Tone to Cool, Normal, Warm, or Custom, the Color Temp function is
disabled.
If you set the Color Tone to Off, the Color Control function is disabled
Color Control
Adjusts individual Red, Green, Blue color balance.
MENU →
→ ENTER → [Picture] →
→
→ → ENTER → [Color Control]
Note
If you adjust the picture by using the Color Control function, Color Tone will turn to the Custom mode.
Red
MENU → → ENTER → [Picture] →
[Red] → , → ENTER
→
→ → ENTER → [Color Control] → ENTER →
Green
MENU → → ENTER → [Picture] → → → → ENTER → [Color Control] → → ENTER
→ [Green] → , → ENTER
Adjusting the PDP Display
Blue
MENU → → ENTER → [Picture] →
ENTER → [Blue] → , → ENTER
→
→ → ENTER → [Color Control] →
→
→
Color Temp.
MENU → → ENTER → [Picture] → → → → ENTER → [Color Temp.] → , → ENTER
Color Temp. is a measure of the 'warmth' of the image colors.
Note
This function is only enabled if the Color Tone is set to Off.
Image Lock
Image Lock is used to fine-tune and get the best image by removing noise that creates unstable images with jitters and shakiness. If satisfactory results are not obtained using the Fine
adjustment, use the Coarse adjustment and then use Fine again.
(Available in PC mode only)
MENU →
→ ENTER → [Picture] →
→
→ → → ENTER → [Image Lock]
MENU → → ENTER → [Picture] →
→ [Coarse] → , → ENTER
→
→ → → ENTER → [Image Lock] → ENTER
Coarse
Removes noise such as vertical stripes. Coarse adjustment may move the screen image
area. You may relocate it to the center using the horizontal control menu.
Fine
MENU → → ENTER → [Picture] →
ENTER → [Fine] → , → ENTER
→
→ → → ENTER → [Image Lock] →
→
Removes noise such as horizontal stripes. If the noise persists even after Fine tuning, repeat
it after adjusting the frequency (clock speed).
H-Position
MENU → → ENTER → [Picture] → → → → → ENTER → [Image Lock] →
→ ENTER → [H-Position] → , → ENTER
Adjusts the screen location horizontally.
→
Adjusting the PDP Display
V-Position
MENU → → ENTER → [Picture] → → → → → ENTER → [Image Lock] →
→ ENTER → [V-Position] → , → ENTER
→
→
Adjusts the screen location vertically.
Auto Adjustment
MENU →
→ ENTER → [Picture] →
→
→ → → ENTER → [Auto Adjustment ]
→
The values of Fine, Coarse, Position are adjusted automatically. By changing the resolution
in the control panel, the auto function is performed.
(Available in PC mode only)
Note
The direct button on the remote control is the 'AUTO' button.
Signal Balance
This is used to make up for the weak RGB signal transmitted by a long signal cable.
MENU →
ance]
→ ENTER → [Picture] →
→
→
→ → → → ENTER → [Signal Bal-
(Available in PC mode only)
Signal Balance
MENU → → ENTER → [Picture] → → → → → → → ENTER → [Signal Balance] → ENTER → [Signal Balance] → , → ENTER
Selects either On or Off with the signal control.
Signal Control
MENU → → ENTER → [Picture] →
→ → ENTER → [Signal Control]
1.
→
→
→ → → → ENTER → [Signal Balance]
R-Gain
MENU → → ENTER → [Picture] → → → → → → → ENTER → [Signal
Balance] → → ENTER → [Signal Control] → ENTER → [R-Gain] → , → ENTER
Adjusting the PDP Display
2.
G-Gain
MENU → → ENTER → [Picture] → → → → → → → ENTER → [Signal
Balance] → → ENTER → [Signal Control] → → ENTER → [G-Gain] → , → ENTER
3.
B-Gain
MENU → → ENTER → [Picture] → → → → → → → ENTER → [Signal
Balance] → → ENTER → [Signal Control] → → → ENTER → [B-Gain] → , →
ENTER
4.
R-Offset
MENU → → ENTER → [Picture] → → →
Balance] → → ENTER → [Signal Control] → →
→ ENTER
5.
→ → → → ENTER → [Signal
→ → ENTER → [R-Offset] → ,
G-Offset
MENU → → ENTER → [Picture] → → → → → → → ENTER → [Signal
Balance] → → ENTER → [Signal Control] → → → → → ENTER → [G-Offset] → , → ENTER
6.
B-Offset
MENU → → ENTER → [Picture] → → → → → → → ENTER → [Signal
Balance] → → ENTER → [Signal Control] → → → → → → ENTER → [BOffset] → , → ENTER
Size
MENU → → ENTER → [Picture] →
→ ENTER
→
→
→ → → → → ENTER → [Size] →
,
Adjusting the PDP Display
The Size can be switched.
1.
16:9
2.
4:3
Picture [ AV / HDMI / DVI / COMPONENT]
Available Modes
•
PC / DVI / BNC
•
AV
•
HDMI / DVI
•
Component
Mode
MENU →
→ ENTER → [Picture] → ENTER → [Mode] →
,
→ ENTER
The PDP Display has four automatic picture settings ("Dynamic", "Standard", "Movie" and
"Custom") that are preset at the factory.
Dynamic, Standard, Movie, or Custom can be activated.
1.
Dynamic
2.
Standard
3.
Movie
4.
Custom
Note
The direct button on the remote control is the 'P.MODE' button.
Custom
By using the on-screen menus, the contrast and brightness can be changed to your personal
preference.
MENU →
→ ENTER → [Picture] →
→ ENTER → [Custom]
Contrast
MENU → → ENTER → [Picture] →
, → ENTER
→ ENTER → [Custom] → ENTER→ [Contrast] →
Adjusting the PDP Display
Adjusts the Contrast.
Brightness
MENU → → ENTER → [Picture] →
ness] → , → ENTER
→ ENTER → [Custom] →
→ ENTER→ [Bright-
Adjusts the Brightness.
Sharpness
MENU → → ENTER → [Picture] →
[Sharpness] → , → ENTER
→ ENTER → [Custom] →
→ ENTER→
→
Adjusts the picture Sharpness.
Color
MENU → → ENTER → [Picture] →
[Color] → , → ENTER
→ ENTER → [Custom] →
→
→ ENTER→
→
Adjusts the picture Color.
Tint
MENU → → ENTER → [Picture] →
→ [Tint] → , → ENTER
→ ENTER → [Custom] →
→
→ →
→ ENTER
Adds a natural tone to the display.
Color Tone
MENU →
→ ENTER → [Picture] →
→
→ ENTER → [Color Tone] →
,
→ ENTER
The color tones can be changed. The individual Color components are also user adjustable.
Adjusting the PDP Display
1.
Off
2.
Cool2
3.
Cool1
4.
Normal
5.
Warm1
6.
Warm2
Note
If you set the Color Tone to Cool2, Cool1, Normal, Warm1, or Warm2, the Color Temp function
is disabled.
Color Temp.
MENU → → ENTER → [Picture] → → → → ENTER → [Color Temp.] → , → ENTER
Color temp. is a measure of the 'warmth' of the image colors.
Note
This function is only enabled if the Color Tone is set to Off.
Size
MENU →
→ ENTER → [Picture] →
→
→
→ → ENTER → [Size] →
,
→ ENTER
The Size can be switched.
1.
16:9 - Sets the picture to 16:9 wide mode.
2.
Zoom 1 - Magnifies the size of the picture on the screen.
3.
Zoom 2 - Magnifies the size of the picture more than “Zoom 1”.
4.
4:3 - Sets the picture to 4:3 normal mode.
5.
Just Scan - Displays the input scenes as they are without any cutoff when HDMI 720p,
1080i, 1080p signals are input.
Note
Certain external devices may feed the display an out of spec signal that may cause cutoff
even when using the Just Scan feature.
Adjusting the PDP Display
ZOOM1, ZOOM2 will be unavailabel in HDMI mode.
Note
The Position and Reset functions are available when Zoom1 or Zoom2 is run.
Digital NR (Digital Noise Reduction)
MENU → → ENTER → [Picture] →
→ ENTER
→
→
→ → → ENTER → [Digital NR] →
,
Turns the Digital Noise Reduction feature Off/On. The Digital Noise Reduction feature allows
you to enjoy clearer and crisper images.
1.
Off
2.
On
Film Mode
MENU → → ENTER → [Picture] →
, → ENTER
→
→
→
→
→
→ ENTER → [Film Mode ] →
The Film Mode feature offers you a theater-quality viewing experience.
(In HDMI mode, this function can be available when the input signal is interlaced scan; it
cannot be available with progressive scan signal.)
1.
Off
2.
On
Sound
Available Modes
•
PC / DVI / BNC
•
AV
•
HDMI
Adjusting the PDP Display
•
Component
Mode
MENU →
→ → ENTER → [Sound] → ENTER → [Mode] →
,
→ ENTER
The PDP Display has a built-in high fidelity stereo amplifier.
1.
Standard
Selects Standard for the standard factory settings.
2.
Music
Selects Music when watching music videos or concerts.
3.
Movie
Selects Movie when viewing movies.
4.
Speech
Selects Speech when watching a show that is mostly dialogue (i.e., news).
5.
Custom
Selects Custom if you want to adjust the settings according to your personal preferences.
Custom
The sound settings can be adjusted to suit your personal preferences.
MENU →
→ → ENTER → [Sound] → → ENTER → [Custom ]
Note
•
You can hear the sound even when sound value is set to 0.
•
If you adjust sound using Custom function, Mode will turn to Custom mode.
Bass
MENU → → → ENTER → [Sound] → → ENTER → [Custom ]→ENTER→ [Bass] → ,
→ ENTER
Emphasizes low frequency audio.
Adjusting the PDP Display
Treble
MENU → → → ENTER → [Sound] → → ENTER → [Custom ]→ →ENTER→ [Treble] →
, → ENTER
Emphasizes high frequency audio.
Balance
MENU → → → ENTER → [Sound] → → ENTER → [Custom ]→ → →ENTER→ [Balance] → , → ENTER
Allows you to Adjusts the sound balance between the left and right speakers.
Auto Volume
MENU →
→ → ENTER → [Sound] → → → ENTER → [Auto Volume] →
,
→ ENTER
Reduces the difference in volume control between broadcasters.
1.
Off
2.
On
SRS TS XT
MENU → → → ENTER → [Sound] → → → → ENTER → [SRS TS XT] → , → ENTER
SRS TS XT is a patented SRS technology that solves the problem of playing 5.1 multichannel
content over two speakers. TruSurround delivers a compelling, virtual surround sound experience through any two-speaker playback system, including internal television speakers. It
is fully compatible with all multichannel formats.
1.
Off
Adjusting the PDP Display
2.
On
Note
The direct button on the remote control is the 'SRS' button.
Setup
Available Modes
•
PC / DVI / BNC
•
AV
•
HDMI
•
Component
Language
MENU →
→ → → ENTER → [Setup] → ENTER → [Language ] →
,
→ ENTER
You can choose one of 13 languages.
Note
The language chosen affects only the language of the OSD. It has no effect on any software
running on the computer.
Time
Selects from one of 4 time settings, Clock Set, Sleep Timer, On Timer, and Off Timer.
MENU →
→ → → ENTER → [Setup] →
→ ENTER → [Time ]
Clock Set
MENU →
Set] → ,
→ → → ENTER → [Setup] →
→ , → ENTER
→ ENTER → [Time ] → ENTER→ [Clock
Adjusting the PDP Display
Current Time Setting.
Sleep Timer
MENU →
Timer] →
→ → → ENTER → [Setup] →
, → ENTER
→ ENTER → [Time ] →
→ ENTER→ [Sleep
Turns the PDP Display off automatically at certain times.
1.
Off
2.
30
3.
60
4.
90
5.
120
6.
150
7.
180
On Timer
MENU → → → → ENTER → [Setup] →
[On Timer] → , / , → ENTER
→ ENTER → [Time ] → →
→ ENTER→
Turns the PDP Display on automatically at a preset time. Controls the mode and the volume
level at the time the PDP Display turns on automatically.
Off Timer
MENU → → → → ENTER → [Setup] →
→ [Off Timer] → , / , → ENTER
→ ENTER → [Time ] → → →
→ ENTER
Adjusting the PDP Display
Turns the PDP Display off automatically at a preset time.
Menu Transparency
MENU → → → → ENTER → [Setup] → →
→ ENTER
→ ENTER → [Menu Transparency] →
,
Change the transparency of the background of the OSD.
1.
High
2.
Medium
3.
Low
4.
Opaque
Safety Lock PIN
MENU → → → → ENTER → [Setup] → → →
[0∼9] → [0∼9] → [0∼9] → [0∼9]
→ ENTER → [Safety Lock PIN ] →
The password can be changed.
•
Change Lock Pin :Changes the product pin number.
•
Lock On/Off : When it is set to Lock On, the remote control buttons are inactive and the
pin number input window will be displayed on the screen. Input the pin number to change
the setting to Lock Off. To return to Lock On, change the setting in the Lock On/ Off mode.
Adjusting the PDP Display
Note
The preset password for the PDP Display is "0000"
Initializing the Safety Lock pin number: INFO + EXIT + MUTE
Energy Saving
MENU → → → → ENTER → [Setup] → → → →
, → ENTER
→ ENTER → [Energy Saving] →
This feature adjusts the power consumption of the unit in order to save energy.
1.
Off
2.
On
HDMI Black Level
MENU →
Level ] →
→ → → ENTER → [Setup] → → → →
, → ENTER
→
→ ENTER → [HDMI Black
When a DVD or set-top box is connected to your TV via HDMI, it may cause a degradation
in the screen quality, such as an increase in the black level, a low contrast, or discoloration,
etc., depending on the external device connected. In this case, adjust the screen quality of
your TV by configuring the HDMI black level.
1.
Normal
2.
Low
Video Wall
A Video Wall is a set of video screens connected together, so that each screen shows a part
of the whole picture or where the same picture is repeated on each screen.
When the Video Wall is on, you can adjust the Video Wall screen setting.
MENU →
Wall ]
→ → → ENTER → [Setup] → → → →
→
→
→ ENTER → [Video
Adjusting the PDP Display
Note
When Video Wall is running, the Auto Adjustment, Image Lock, and Size functions are not
available. Video Wall does not operate in MagicInfo mode.
Video Wall
MENU → → → → ENTER → [Setup] → → → →
Wall ]→ ENTER → [Video Wall ] → , → ENTER
→
→
→ ENTER → [Video
Turns Off/On the Video Wall function of the selected display Off/On.
1.
Off
2.
On
Format
MENU → → → → ENTER → [Setup] → → → →
Wall ]→ → ENTER → [Format] → , → ENTER
→
→
→ ENTER → [Video
→
→ ENTER → [Video
The Format can be selected to see a divided screen.
1.
Full
Provides a full screen without any margins.
2.
Natural
Displays a natural image with the original aspect ratio intact.
Horizontal
MENU → → → → ENTER → [Setup] → → → → →
Wall ]→ → → ENTER → [Horizontal] → , → ENTER
Adjusting the PDP Display
Sets how many parts the screen should be divided horizontally.
Five adjustment levels: 1, 2, 3, 4, and 5.
Vertical
MENU → → → → ENTER → [Setup] → → → → →
Wall ]→ → → → ENTER → [Vertical] → , → ENTER
→
→ ENTER → [Video
→
→ ENTER → [Video
Sets how many parts the screen should be divided vertically.
Five adjustment levels: 1, 2, 3, 4, and 5.
Screen Divider
MENU → → → → ENTER → [Setup] → → → →
Wall ]→ → → → → ENTER → [Screen Divider]
→
The screen can be divided into several images. A number of screens can be selected with a
different layout when dividing.
•
Select a mode in Screen Divider.
•
Select a display in Display Selection.
•
The selection will be set up by pressing a number in the selected mode.
Safety Screen
The Safety Screen function is used to prevent afterimages that may appear when a still picture
is displayed on the screen over a long time.
Adjusting the PDP Display
•
The Safety Screen function scrolls the screen for the specified period of time.
•
This function is not available when the power is turned off.
MENU → → → → ENTER → [Setup] → → → → → → → → ENTER → [Safety
Screen]
Pixel Shift
Pixel Shift
MENU → → → → ENTER → [Setup] → → → → → → → → ENTER → [Safety
Screen] → ENTER → [Pixel Shift] → ENTER → [Pixel Shift] → , → ENTER
To prevent after-images on the screen you can use this function, so that every minute pixels
on the PDP are moved in horizontal or vertical direction.
1.
Off
2.
On
Note
The Pixel Shift is not available when Video Wall is On.
Horizontal Dot
MENU → → → → ENTER → [Setup] → → → → → → → → ENTER → [Safety
Screen] → ENTER → [Pixel Shift] → → ENTER → [Horizontal Dot] → , → ENTER
Sets how many pixels the screen moves horizontally.
Five adjustment levels: 0, 1, 2, 3, and 4.
Vertical Line
MENU → → → → ENTER → [Setup] → → → → → → → → ENTER → [Safety
Screen] → ENTER → [Pixel Shift] → → → ENTER → [Vertical Line] → , → ENTER
Adjusting the PDP Display
Sets how many pixels the screen moves vertically.
Five adjustment levels: 0, 1, 2, 3, and 4.
Time
MENU → → → → ENTER → [Setup] → → → → → → → → ENTER → [Safety
Screen] → ENTER → [Pixel Shift] → → → → ENTER → [Time] → , → ENTER
Set the time interval for performing the horizontal or vertical movement, respectively.
Timer
Timer
MENU → → → → ENTER → [Setup] → → → → → → → → ENTER → [Safety
Screen] → → ENTER → [Timer] → ENTER → [Timer] → , → ENTER
You can set the timer for Screen Burn Protection.
If you start the operation to erase any residual image, the operation will be performed for the
set period of time and then automatically finish.
1.
Off
2.
On
Mode
MENU → → → → ENTER → [Setup] → → → → → → → → ENTER → [Safety
Screen] → → ENTER → [Timer] → → ENTER → [Mode] → , → ENTER
Adjusting the PDP Display
You can change the Safety Screen Type.
1.
Scroll
2.
Bar
3.
Eraser
4.
All White
5.
Pattern
Period
MENU → → → → ENTER → [Setup] → → → → → → → → ENTER → [Safety
Screen] → → ENTER → [Timer] → → → ENTER → [Period] → , → ENTER
Use this function to set the execution period for each mode set in the timer.
Time
MENU → → → → ENTER → [Setup] → → → → → → → → ENTER → [Safety
Screen] → → ENTER → [Timer] → → → → ENTER → [Time] → , → ENTER
Within the set period of time specify a time for execution.
•
Mode-Scroll : 1~5 sec
•
Mode-Bar, Eraser : 10~50 sec
•
Mode-All White, Pattern : 1, 5, 10, 20 30 min
Adjusting the PDP Display
Scroll
MENU → → → → ENTER → [Setup] → → → → → → → → ENTER → [Safety
Screen] → → → ENTER → [Scroll]
This function prevents after-images on the screen by moving all the pixels on the PDP according to a pattern.
Use this function when there are remaining after-images or symbols on the screen, especially
when you displayed a still image on the screen for a long time.
Bar
MENU → → → → ENTER → [Setup] → → → → → → → → ENTER → [Safety
Screen] → → → →ENTER → [Bar]
This function prevents after-images on the screen by moving long black and white vertical
lines.
Eraser
MENU → → → → ENTER → [Setup] → → → → → → → → ENTER → [Safety
Screen] → → → → →ENTER → [Eraser]
This function prevents after-images on the screen by moving a rectangular pattern.
All White
MENU → → → → ENTER → [Setup] → → → → → → → → ENTER → [Safety
Screen] → → → → → →ENTER → [All White]
Adjusting the PDP Display
This function prevents after-images on the screen by changing the color of pixels to white.
Use this function when there are remaining after-images or symbols on the screen, especially
when you displayed a still image on the screen for a long time.
Pattern
MENU → → → → ENTER → [Setup] → → → → → → → → ENTER → [Safety
Screen] → → → → → → →ENTER → [Pattern]
This function prevents after-images on the screen by moving a diagonal pattern stored in the
panel repeatedly.
Resolution Select
MENU → → → → ENTER → [Setup] → → → →
[Resolution Select ] → , → ENTER
→
→
→
→
→ENTER →
When the picture is not displayed properly on the screen when setting the graphics card
resolution of the computer to 1024 x 768 @ 60Hz, 1280 x 768 @ 60Hz, 1360 x 768@ 60Hz
or 1366 x768 @ 60Hz, by using this function(Resolution Select), you can have the picture
displayed on the screen in the specified resolution.
Note
Available in PC mode only
1.
Off
2.
1024 X 768
Adjusting the PDP Display
3.
1280 X 768
4.
1360 x 768
5.
1366 X 768
Note
Selecting the menu is only allowed when the graphics resolution is set to 1024 x 768 @ 60Hz,
1280 x 768 @ 60Hz, 1360 x 768@ 60Hz or 1366 x768 @ 60Hz.
Power On Adjustment
MENU → → → → ENTER → [Setup] → → → →
→ [Power On Adjustment ] → , → ENTER
→
→
→
→
→ → ENTER
Adjusts the Power On time for the screen.
Caution: Set the Power On time to be longer to avoid overvoltage.
Side Gray
MENU → → → → ENTER → [Setup] → → → →
ENTER → [Side Gray] → , → ENTER
→
→
→
→
→ → →
Select the brightness of the grey for the screen background.
1.
Off
2.
Light
3.
Dark
Reset
Reverts the product settings to factory defaults. The Reset function is only available when
PC / DVI is being used.
Adjusting the PDP Display
MENU → → → → ENTER → [Setup] → → → →
→ ENTER → [Reset ]
→
→
→
→
→ → →
MENU → → → → ENTER → [Setup] → → → → → → →
→ ENTER → [Reset ]→ ENTER → [Image Reset ] → , → ENTER
→
→ → →
→
→ → →
Image Reset
Note
Available in PC mode only
Note
The Reset function is not available when Video Wall is On.
Color Reset
MENU → → → → ENTER → [Setup] → → → → → → →
→ ENTER → [Reset ]→ → ENTER → [Color Reset ] → , → ENTER
OSD Rotation
MENU → → → → ENTER →
→
→ → → → ENTER → [OSD Rotation ]
→
,
→ ENTER
OSD Rotate
1.
Landscape
2.
Portrait
Multi Control
Available Modes
•
PC / DVI / BNC
•
AV
•
HDMI
•
Component
→
→
→
→
→
→
→
→
→
Adjusting the PDP Display
Multi Control
Assigns an individual ID to the SET.
MENU →
•
→ → →
→ ENTER → [Multi Control ] → ENTER →
,
→ [0~9]
ID Setup
Assigns distinctive IDs to the SET.
•
ID Input
Use to select the transmitter functions of the individual SET. Only a SET where the ID
corresponds to the transmitter setting becomes activated.
Troubleshooting
Self-Test Feature Check
Note
Check the following items yourself before calling for assistance. Contact a Service Center for
problems that you cannot solve by yourself.
Self-Test Feature Check
1.
Turn off both your computer and the PDP Display.
2.
Unplug the video cable from the back of the computer.
3.
Turn on the PDP Display.
The figure shown below ("Check Signal Cable") appears on a black background when
the PDP Display is working normally even though no video signal is detected: While in
the Self-Test mode, the LED power indicator remains green and the figure moves around
on the screen.
4.
Turn off your PDP Display and reconnect the video cable; then turn on both your computer and the PDP Display
If your PDP Display screen remains blank after using the previous procedure, check your
video controller and computer system; your PDP Display is functioning properly.
Warning Messages
You can even view the screen at a resolution of 1360(1920) x 768(1080). However, you will
receive the following message for a minute; You can choose to change the screen resolution
or stay in the current mode during that time. And if the resolution is more than 85Hz, you will
see the black screen because the PDP Display does not support over 85Hz.
Note
Refer to Specifications > Preset Timing Modes for the resolutions or frequencies supported
by the PDP Display.
Maintenance and Cleaning
1) Maintaining the PDP Display Case.
Clean with a soft cloth after disconnecting the power cord.
Troubleshooting
•
Do not use benzene, thinner or other flammable substances, or a wet cloth.
•
We recommend that a SAMSUNG cleansing agent
is used to prevent damage to the screen.
2) Maintaining the Flat Panel Display Screen.
Clean with a soft cloth (cotton flannel) smoothly.
•
Never use acetone, benzene or thinner.
(They may cause flaws or deformation of the screen
surface.)
•
The user will be required to pay costs and related
expenses for repairing damages caused.
Symptoms and Recommended Actions
Note
A PDP Display recreates visual signals received from the computer. Therefore, if there is a
problem with the computer or the video card, this can cause the PDP Display to become
blank, have poor coloring, become noisy, and video mode not supported, etc. In this case,
first check the source of the problem, and then contact a Service Center or your dealer.
1.
Check if the power cord and the video cables are properly connected to the computer.
2.
Check if the computer beeps more than 3 times when booting.
(If it does, request an a service for the main board of the computer.)
3.
If you installed a new video card or if you assembled the PC, check if you installed the
Adaptor(video).
4.
Check if the scanning ratio of the video screen is set to between 50 Hz ~ 85 Hz.
(Do not exceed 60Hz when using the maximum resolution.)
5.
If you have problems in installing the Adaptor (video) driver, boot the computer in Safe
Mode, remove the Display Adaptor in the "Control Panel −> System −> Device Administrator" and then reboot the computer to reinstall the Adaptor (video) driver.
Check List
Note
•
The following table lists possible problems and their solutions. Before calling for assistance, check the information in this section to see if you can remedy any problems for
yourself. If you do need assistance, please call the phone number on the Information
section or contact your dealer.
Problems related to the Installation (PC Mode)
Note
Problems related to the PDP Display installation and their solutions are listed.
Q:
The PDP Display screen flickers.
Troubleshooting
A:
Check if the signal cable between the computer and the PDP Display is securely connected.
(Refer to Connecting a Computer)
Problems related to the Screen
Note
Problems related to the PDP Display screen and their solutions are listed.
Q:
The screen is blank and the power indicator is off.
A:
Ensure that the power cord is firmly connected and the PDP Display is on.
(Refer to the Connecting a Computer)
Q:
"Check Signal Cable" message.
A:
Ensure that the signal cable is firmly connected to the PC or video sources.
(Refer to the Connecting a Computer)
A:
Ensure that the PC or video sources are turned on.
Q:
"Not Optimum Mode" message.
A:
Check the maximum resolution and the frequency of the video Adaptor.
A:
Compare these values with the data in the Preset Timing Modes Chart.
Q:
The picture rolls vertically.
A:
Check if the signal cable is securely connected. Re-connect it, if necessary.
(Refer to Connecting a Computer)
Q:
The image is not clear; picture is blurred.
A:
Run Frequency Coarse and Fine tuning.
A:
Turn on again after removing all accessories (video extension cable, etc.)
A:
Set the resolution and frequency to the recommended ranges.
Q:
The picture image is unstable and shakes.
A:
Check if the resolution and frequency set for the computer video card falls in the range
supported by the PDP Display. If not, reset them referring to the current Information
under the PDP Display menu and Preset Timing Modes.
Q:
Ghost images are shown in the picture.
A:
Check if the resolution and frequency set for the computer video card falls in the range
supported by the PDP Display. If not, reset them referring to the current Information
under the PDP Display menu and Preset Timing Modes.
Q:
The image is too light or too dark.
A:
Adjusts the brightness and contrast.
(Refer to the Brightness, Contrast)
Troubleshooting
Q:
The screen color is inconsistent.
A:
Adjust color using Custom under OSD Color Adjustment menu.
Q:
The color image is distorted by dark shadows.
A:
Adjust color using Custom under OSD Color Adjustment menu.
Q:
The color white is poor.
A:
Adjust color using Custom under OSD Color Adjustment menu.
Q:
The Power Indicator blinks.
A:
The PDP Display is currently saving the changes made in the settings to the OSD
memory.
Q:
The screen is blank and the power indicator light blinks every 0.5 or 1 seconds. The
PDP Display is using its power management system. Press any key on the keyboard.
A:
The PDP Display is using its power management system. Press a key on the keyboard.
Q:
The screen is blank and it is blinking.
A:
If you see the "TEST GOOD" message on the screen when you pressing the MENU
button, check the cable connection between the PDP Display and the computer to ensure that the connector is properly connected.
Problems related to Audio
Note
Problems related to audio signals and their solutions are listed below.
Q:
No sound.
A:
Ensure that the audio cable is firmly connected to both the audio-in port on your PDP
Display and the audio-out port on your sound card.
(Refer to the Connecting a Computer)
A:
Check the volume level.
Q:
The sound level is too low.
A:
Check the volume level.
A:
If the volume is still too low after turning the control to its maximum, check the volume
control on the computer sound card or software program.
Q:
The sound is too high or too low.
A:
Adjusts the Treble and Bass to the appropriate levels.
Problems related to the Remote Control
Note
Problems related to the remote control and their solutions are listed.
Q:
The remote control buttons do not respond.
A:
Check the polarities (+/-) of the batteries.
Troubleshooting
A:
Check if the batteries are empty.
A:
Check if the power is on.
A:
Check if the power cord is securely connected.
A:
Check if a special fluorescent or neon lamp is on in the vicinity.
Q:
How can I change the frequency?
A:
The frequency can be changed by reconfiguring the video card.
Q&A
Note
That video card support can vary, depending on the version of the driver used. (Refer
to the computer or the video card manual for details.)
Q:
How can I Adjusts the resolution?
A:
Windows XP:
Set the resolution in the Control Panel → Appearance and Themes → Display → Settings.
A:
Windows ME/2000:
Set the resolution in the Control Panel → Display → Settings.
* Contact the video card manufacturer for details.
Q:
How can I set the Power Saving function?
A:
Windows XP:
Set the resolution in the Control Panel → Appearance and Themes → Display → Screen
Saver.
Set the function in the BIOS-SETUP of the computer. (Refer to the Windows / Computer
Manual).
A:
Windows ME/2000:
Set the resolution at the Control Panel → Display → Screen Saver.
Set the function in the BIOS-SETUP of the computer. (Refer to the Windows / Computer
Manual).
Q:
How can I clean the outer case/PDP Panel?
A:
Disconnect the power cord and then clean the PDP Display with a soft cloth, using either
a cleaning solution or plain water.
Do not leave any detergent or scratches on the case. Do not let any water enter the
PDP Display.
Q:
How can I play the video?
A:
The video supports the MPEG1 and WMV codecs only. Install the corresponding codec
to play the video. Note that some of the codecs can be incompatible.
Troubleshooting
Note
Before calling for assistance, check the information in this section to see if you can remedy
any problems yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer.
Specifications
General
General
Model Name
SyncMaster P50HP / SyncMaster P50FP / SyncMaster
P63FP
PDP Panel
Size
Display area
Pixel Pitch
SyncMaster
P50HP
50 " Diagonal (126 cm)
SyncMaster
P50FP
50 " Diagonal (126 cm)
SyncMaster
P63FP
63 " Diagonal (160 cm)
SyncMaster
P50HP
1105.65 mm (H) x 622.1 mm (V)
SyncMaster
P50FP
1105.65 mm (H) x 622.1 mm (V)
SyncMaster
P63FP
1393.92 mm (H) x 784.1 mm (V)
SyncMaster
P50HP
0.810 mm (H) x 0.810 mm (V)
SyncMaster
P50FP
0.576 mm (H) x 0.576 mm (V)
SyncMaster
P63FP
0.726 mm (H) x 0.726 mm (V)
Synchronization
Horizontal
30 ~ 81 kHz
Vertical
56 ~ 75 Hz
Display Color
16.7 M
Resolution
Optimum resolu- P50HP
tion
1360 x 768 @ 60 Hz (Depends on graphics card
used)
P50FP
1920 x 1080 @ 60 Hz
P63FP
1920 x 1080 @ 60 Hz
Maximum resolu- P50HP
tion
P50FP
1920 x 1080 @ 60 Hz
P63FP
1920 x 1080 @ 60 Hz
1920 x 1080 @ 60 Hz
Input Signal, Terminated
RGB Analog, DVI Compliant Digital RGB
0.7 Vp-p ±5 %
Specifications
Input Signal, Terminated
Separate H/V sync, Composite, SOG(Option)
TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)
Maximum Pixel Clock
165MHz (Analog,Digital)
Power Supply
AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz
Signal connectors
D-sub, DVI-D, BNC, AV(Composite, CVBS), HDMI, RS232C In/Out
PC Audio In, Audio In(Stereo), Audio Out(Stereo)
Dimensions (W x H x D) / Weight
SyncMaster P50HP
1204.6 x 724.1 x 97.1 mm (47.4 x 28.5 x 3.8 inch) (Without
Stand) / 32.7 kg (72.1 lbs)
1204.6 x 773.2 x 362.4 mm (47.4 x 30.4 x 14.3 inch) (With
Stand)
SyncMaster P50FP
1204.6 x 724.1 x 97.1 mm (47.4 x 28.5 x 3.8 inch) (Without
Stand) / 33.7 kg (74.3 lbs)
1204.6 x 773.2 x 362.4 mm (47.4 x 30.4 x 14.3 inch) (With
Stand)
SyncMaster P63FP
1503.5 x 894.0 x 99.4 mm (59.2 x 35.2 x 3.9 inch) (Without
Stand) / 51.8 kg (114.2 lbs)
VESA Mounting Interface
SyncMaster P50HP
600 x 400 mm
SyncMaster P50FP
600 x 400 mm
SyncMaster P63FP
676 x 407 mm
Environmental considerations
Operating
Temperature : 32°F ~ 104°F (0°C ~ 40°C)
Humidity : 10 % ~ 80 %, non-condensing
Reliability - MTBF
More than 50,000 hours at 90% confidence level.
Storage
Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Humidity : 5 % ~ 95 %, non-condensing
Audio Characteristics
Audio Input
RCA Jack Red(R) White(L), 0.5 Vrms (-9 dB)
Audio Output
RCA Jack Red(R) White(L), 0.5 Vrms (-9 dB)
PC Audio Input
3.5 øStereo Jack, 0.5 Vrms (-9 dB)
Frequency
RF: 80 Hz ~ 15 kHz (at -3 dB)
Response
A/V: 80 Hz ~ 20 kHz (at -3 dB)
Specifications
Plug and Play Capability
This PDP Display can be installed on any Plug & Play compatible system. The
interaction of the PDP Display and the computer systems will provide the best operating conditions and PDP Display settings. In most cases, the PDP Display
installation will proceed automatically, unless the user wishes to select alternate
settings.
Dot Acceptable
PDP panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above are used for this product. But the pixels of
RED, GREEN, BLUE and WHITE color appear to be bright sometimes or some
black pixels may be seen. This is not from bad quality and you can use it without
any problems.
For example, the number of PDP sub pixels contained in this product are 3,133,440
(P50HP).
For example, the number of PDP sub pixels contained in this product are 6,220,800
(P50FP, P63FP).
Note
Design and specifications are subject to change without prior notice.
Class B Equipment (Information Communication equipment for residential use)
This product complies with the Electromagnetic Compatibility Directives for residential use
and can be used in all areas including common residential areas. (Class B equipment emits
less electromagnetic waves than Class A equipment.)
PowerSaver
This PDP Display has a built-in power management system called PowerSaver. This system
saves energy by switching your PDP Display to low-power mode when it has not been used
for a certain amount of time. The PDP Display automatically returns to normal operation when
you press a key on the keyboard. For energy conservation, turn your PDP Display OFF when
it is not needed, or when leaving it unattended for long periods. The PowerSaver system
operates with a VESA DPM compliant video card installed in your computer. Use the software
utility installed on your computer to set up this feature.
PowerSaver
State
Power Indicator
P50HP
Power ConsumpP50FP
tion
P63FP
Normal Opera- Power saving
tion
mode
On
350 W
420 W
560 W
Power off
EPA/ENERGY
2000
On, Blinking
Off
Less than 2
watts
Less than 1
watts
Specifications
This monitor is EPA ENERGY STAR® compliant and
ENERGY 2000 compliant when used with a computer
equipped with VESA DPM functionality.
As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets the ENERGY STAR®
guidelines for energy efficiency.
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes,
the screen will be adjusted automatically. However, if the signal differs, the screen may go
blank while the power LED is on. Refer to the video card manual and adjusts the screen as
follows.
SyncMaster P50HP
Display Mode
Horizontal
Frequency
(kHz)
IBM, 640 x 350
31.469
70.086
25.175
+/-
IBM, 640 x 480
31.469
59.940
25.175
-/-
IBM, 720 x 400
31.469
70.087
28.322
-/+
MAC, 640 x 480
35.000
66.667
30.240
-/-
MAC, 832 x 624
49.726
74.551
57.284
-/-
MAC, 1152 x 870
68.681
75.062
100.000
-/-
VESA, 640 x 480
37.861
72.809
31.500
-/-
VESA, 640 x 480
37.500
75.000
31.500
-/-
VESA, 800 x 600
35.156
56.250
36.000
+/+
VESA, 800 x 600
37.879
60.317
40.000
+/+
VESA, 800 x 600
48.077
72.188
50.000
+/+
VESA, 800 x 600
46.875
75.000
49.500
+/+
VESA, 1024 x 768
48.363
60.004
65.000
-/-
VESA, 1024 x 768
56.476
70.069
75.000
-/-
VESA, 1024 x 768
60.023
75.029
78.750
+/+
VESA, 1152 x 864
67.500
75.000
108.000
+/+
VESA, 1280 x 960
60.000
60.000
108.000
+/+
VESA, 1280 x 1024
63.981
60.020
108.000
+/+
VESA, 1280 x 1024
79.976
75.025
135.000
+/+
Vertical Fre- Pixel Clock
quency (Hz)
(MHz)
Sync Polarity
(H/V)
SyncMaster P50FP / SyncMaster P63FP
Display Mode
Horizontal
Frequency
(kHz)
Vertical Fre- Pixel Clock
quency (Hz)
(MHz)
Sync Polarity
(H/V)
IBM, 640 x 350
31.469
70.086
25.175
+/-
IBM, 640 x 480
31.469
59.940
25.175
-/-
IBM, 720 x 400
31.469
70.087
28.322
-/+
Specifications
Display Mode
Horizontal
Frequency
(kHz)
Vertical Fre- Pixel Clock
quency (Hz)
(MHz)
Sync Polarity
(H/V)
MAC, 640 x 480
35.000
66.667
30.240
-/-
MAC, 832 x 624
49.726
74.551
57.284
-/-
MAC, 1152 x 870
68.681
75.062
100.000
-/-
VESA, 640 x 480
37.861
72.809
31.500
-/-
VESA, 640 x 480
37.500
75.000
31.500
-/-
VESA, 800 x 600
35.156
56.250
36.000
+/+
VESA, 800 x 600
37.879
60.317
40.000
+/+
VESA, 800 x 600
48.077
72.188
50.000
+/+
VESA, 800 x 600
46.875
75.000
49.500
+/+
VESA, 848 x 480
31.020
60.000
33.750
+/+
VESA, 1024 x 768
48.363
60.004
65.000
-/-
VESA, 1024 x 768
56.476
70.069
75.000
-/-
VESA, 1024 x 768
60.023
75.029
78.750
+/+
VESA, 1152 x 864
67.500
75.000
108.000
+/+
VESA, 1280 x 768
47.776
59.870
79.500
-/+
VESA, 1280 x 960
60.000
60.000
108.000
+/+
VESA, 1280 x 1024
63.981
60.020
108.000
+/+
VESA, 1280 x 1024
79.976
75.025
135.000
+/+
VESA, 1360 x 768
47.712
60.015
85.500
+/+
VESA, 1600 x 1200
75.000
60.000
162.000
+/+
VESA, 1920 x 1080
66.587
59.934
138.500
+/-
Horizontal Frequency
The time to scan one line connecting the right edge
to the left edge of the screen horizontally is called the
Horizontal Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency.
Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the
same image many times per second to display an
image to the user. The frequency of this repetition is
called the Vertical Frequency or Refresh Rate. Unit:
Hz
Information
For Better Display
Adjust the computer resolution and screen injection rate (refresh rate) on the
computer as described below to enjoy the best picture quality. You can have an
uneven picture quality on screen if the best picture quality is not provided for PDP.
•
Resolution: 1360 x 768 (P50HP)
Resolution: 1920 x 1080 (P50FP , P63FP)
•
Vertical frequency (refresh rate): 60 Hz
PDP panels manufactured by using advanced semiconductor technology with
a precision of 1ppm (one millionth) and above is used for this product. But the pixels
of RED, GREEN, BLUE and WHITE color seem to be bright sometimes or some
of black pixels could be seen. This is not from bad quality and you can use it without
any problems.
•
For example, the number of PDP sub pixels contained in this product are
3,133,440 (P50HP) / 6,220,800 (P50FP, P63FP).
When cleaning the monitor and the panel outside, please apply the recommended small amount of cleaner by using a soft cloth to polish. Do not force the
PDP area but rub softly. If excessive force is applied, you may stain it.
If you are not satisfied with the picture quality, you can get better quality of
picture by performing the "Auto Adjustment function" in display screen that is appeared as window termination button is pressed. If there's still noise after the
automatic adjustment, use the Fine/Coarse adjustment function.
When viewing a fixed screen for an extended period of time, a residual image
or blurriness may appear. Change the mode to energy save or set a screensaver
to move the picture when you need to be away from the monitor for an extended
period of time.
PRODUCT INFORMATION (Image Retention Free)
What is Image Retention ?
Image retention may not occur when a PDP panel is operated under normal conditions.Normal conditions are defined as continuously changing video patterns.
When the PDP panel is operated for a long time with a fixed pattern .
Phosphor degradation may occur and the brightness is decreased. To prevent this,
the video pattern should be changed from time to time.
When viewing a still screen for a long time, the brightness of any part which was
bright in the previous fixed pattern becomes lower than that of its surroundings.
Information
Power Off, Screen Saver, or Power Save Mode
•
Turn the power off for 4 hours after 20 hours in use
•
Turn the power off for 2 hours after 12 hours in use
•
Set the Monitor to power off with the PC Display Properties Power Scheme.
•
Use a Screen saver if possible - Screen saver in one color or a moving image
is recommended.
Change the Color Information periodically
Note
Use Two different colors
Rotate the Color Information with 2 different colors every 30 minutes.
•
Avoid using a combination of characters and background color with large difference in luminance.
Avoid using Grey colors, which can cause Image retention easily.
Avoid: Colors with big difference in luminance (Black & White, Grey)
Change the characters color periodically
Information
•
Use Bright colors with little difference in luminance.
- Cycle : Change the characters color and background color every 30 minutes
•
Every 30 minutes, change the characters with movement.
•
All area display Moving image together with Logo periodically.
- Cycle: Display moving image together with Logo for 60 seconds after 4 hours
in use.
•
The best way to protect your monitor from Image retention is to turn Power off,
or set your PC, or System to operate a Screen Saver program when you are
not using it. Also Warranty service will be limited based on instruction guide.
Apply the Screen Scroll function on Product
•
Apply the Screen Scroll function
- Symptom: Horizontal Bar with Black Color move up and down.
- Select method
•
Instruction Guide : OSD Menu -> Set Up -> Safety Screen -> Screen Scroll
•
Time Interval : 1 ~ 10 hours ( Recommend : 1 )
•
Time Period : 1 ~ 5 second ( Recommend : 5 )
Note
( Please check CD's User Guide at "OSD Function", some model's will not available )
Apply the Screen Pixel function on Product
•
Apply the Screen Pixel function
- Symptom: Dot with Black Color move up and down.
Information
- Select method
•
•
Instruction Guide : OSD Menu -> Set Up -> Safety Screen -> Pixel
•
Time Interval : 1 ~ 10 hours ( Recommend : 1 )
•
Time Period : 10 ~ 50 second ( Recommend : 50 )
Apply the Screen Bar function
- Symptom: Horizontal / Vertical Bar with Black Color move up and down.
- Select method
•
Instruction Guide : OSD Menu -> Set Up -> Safety Screen -> Bar
•
Time Interval : 1 ~ 10 hours ( Recommend : 1 )
•
Time Period : 10 ~ 50 second ( Recommend : 50 )
Note
( Please check CD's User Guide at "OSD Function", some model's will not available. )
Apply the Screen Erasing function on Product
•
Apply the Screen Erasing function
- Symptom: 2 Vertical blocks move with erasing the display
- Select method
•
Instruction Guide : OSD Menu -> Set Up -> Safety Screen -> Eraser
Information
•
Time Interval : 1 ~ 10 hours ( Recommend : 1 )
•
Time Period : 10 ~ 50 second ( Recommend : 50 )
Note
( Please check CD's User Guide at "OSD Function", some model's will not available )
Appendix
Contact SAMSUNG WORLDWIDE
Note
If you have any questions or comments relating to Samsung products, please contact the
SAMSUNG customer care center.
North America
U.S.A
1-800-SAMSUNG(726-7864) http://www.samsung.com/us
CANADA
1-800-SAMSUNG(726-7864) http://www.samsung.com/ca
MEXICO
01-800-SAMSUNG
(726-7864)
http://www.samsung.com/mx
Latin America
ARGENTINA
0800-333-3733
http://www.samsung.com/ar
BRAZIL
0800-124-421
http://www.samsung.com/br
4004-0000
CHILE
800-SAMSUNG(726-7864)
http://www.samsung.com/cl
COLOMBIA
01-8000112112
http://www.samsung.com/co
COSTA RICA
0-800-507-7267
http://www.samsung.com/latin
ECUADOR
1-800-10-7267
http://www.samsung.com/latin
EL SALVADOR
800-6225
http://www.samsung.com/latin
GUATEMALA
1-800-299-0013
http://www.samsung.com/latin
HONDURAS
800-7919267
http://www.samsung.com/latin
JAMAICA
1-800-234-7267
http://www.samsung.com/latin
NICARAGUA
00-1800-5077267
http://www.samsung.com/latin
PANAMA
800-7267
http://www.samsung.com/latin
PUERTO RICO
1-800-682-3180
http://www.samsung.com/latin
REP. DOMINICA
1-800-751-2676
http://www.samsung.com/latin
TRINIDAD & TO- 1-800-SAMSUNG(726-7864) http://www.samsung.com/latBAGO
in
VENEZUELA
0-800-100-5303
http://www.samsung.com/latin
Europe
AUSTRIA
0810 - SAMSUNG (7267864, http://www.samsung.com/at
€ 0.07/min)
Appendix
Europe
BELGIUM
02 201 2418
http://www.samsung.com/be
(Dutch)
http://www.samsung.com/
be_fr (French)
CZECH REPUBLIC 800
(800-726786)
SAMSUNG http://www.samsung.com/cz
DENMARK
8 - SAMSUNG (7267864)
http://www.samsung.com/dk
EIRE
0818 717 100
http://www.samsung.com/ie
FINLAND
30 - 6227 515
http://www.samsung.com/fi
FRANCE
01 4863 0000
http://www.samsung.com/fr
GERMANY
01805
SAMSUNG http://www.samsung.de
(7267864, € 0.14/Min)
HUNGARY
06-80-SAMSUNG (726-7864) http://www.samsung.com/hu
ITALIA
800-SAMSUNG (726-7864)
http://www.samsung.com/it
LUXEMBURG
02 261 03 710
http://www.samsung.com/lu
NETHERLANDS
0900-SAMSUNG
http://www.samsung.com/nl
(0900-7267864) (€ 0,10/Min)
NORWAY
3 - SAMSUNG (7267864)
POLAND
0 801 1SAMSUNG (172678) http://www.samsung.com/pl
http://www.samsung.com/no
022 - 607 - 93 - 33
PORTUGAL
808
20
(7267864)
-
SAMSUNG http://www.samsung.com/pt
SLOVAKIA
0800-SAMSUNG (726-7864) http://www.samsung.com/sk
SPAIN
902 - 1 - SAMSUNG(902 172 http://www.samsung.com/es
678)
SWEDEN
075 - SAMSUNG (726 78 64) http://www.samsung.com/se
SWITZERLAND
0848 - SAMSUNG (7267864, http://www.samsung.com/ch
CHF 0.08/min)
U.K
0845 SAMSUNG (7267864)
http://www.samsung.com/uk
CIS
ESTONIA
800-7267
http://www.samsung.com/ee
LATVIA
8000-7267
http://www.samsung.com/lv
LITHUANIA
8-800-77777
http://www.samsung.com/lt
KAZAKHSTAN
8-10-800-500-55-500
http://www.samsung.com/
kz_ru
KYRGYZSTAN
00-800-500-55-500
RUSSIA
8-800-555-55-55
TADJIKISTAN
8-10-800-500-55-500
UKRAINE
8-800-502-0000
http://www.samsung.ua
UZBEKISTAN
8-10-800-500-55-500
http://www.samsung.com/
kz_ru
http://www.samsung.ru
Appendix
Asia Pacific
AUSTRALIA
1300 362 603
http://www.samsung.com/au
CHINA
800-810-5858
http://www.samsung.com/cn
400-810-5858
010-6475 1880
INDIA
HONG KONG:3698 - 4698
http://www.samsung.com/hk
3030 8282
http://www.samsung.com/in
1-800-3000-8282
1800 110011
INDONESIA
0800-112-8888
http://www.samsung.com/id
JAPAN
0120-327-527
http://www.samsung.com/jp
MALAYSIA
1800-88-9999
http://www.samsung.com/my
NEW ZEALAND
0800 SAMSUNG(0800 726 http://www.samsung.com/nz
786)
PHILIPPINES
1-800-10-SAMSUNG
(726-7864)
http://www.samsung.com/ph
1-800-3-SAMSUNG
(726-7864)
02-5805777
SINGAPORE
1800-SAMSUNG(726-7864) http://www.samsung.com/sg
THAILAND
1800-29-3232, 02-689-3232
http://www.samsung.com/th
TAIWAN
0800-329-999
http://www.samsung.com/tw
VIETNAM
1 800 588 889
http://www.samsung.com/vn
Middle East & Africa
SOUTH AFRICA
0860-SAMSUNG(726-7864) http://www.samsung.com/za
TURKEY
444 77 11
http://www.samsung.com/tr
U.A.E
800-SAMSUNG(726-7864)
http://www.samsung.com/ae
8000-4726
Terms
Dot Pitch
The image on a monitor is composed of red, green and blue
dots. The closer the dots, the higher the resolution. The distance between two dots of the same color is called the 'Dot
Pitch'. Unit: mm
Vertical Frequency
The screen must be redrawn several times per second in
order to create and display an image for the user. The frequency of this repetition per second is called the Vertical
Frequency or Refresh Rate. Unit: Hz
Example: If the same light repeats itself 60 times per second, this is regarded as 60 Hz.
Horizontal Frequency
The time to scan one line connecting the right edge to the
left edge of the screen horizontally is called the Horizontal
Appendix
Cycle. The inverse number of the Horizontal Cycle is called
Horizontal Frequency. Unit: kHz
Interlace and Non-Interlace
Methods
Showing the horizontal lines of the screen from the top to
the bottom sequentially is called the Non-Interlace method
while showing odd lines and then even lines in turn is called
the Interlace method. The Non-Interlace method is used for
the majority of monitors to ensure a clear image. The Interlace method is the same as that used in TVs.
Plug & Play
This is a function that provides the best quality screen for
the user by allowing the computer and the monitor to exchange information automatically. This monitor follows the
international standard VESA DDC for the Plug & Play function.
Resolution
The number of horizontal and vertical dots used to compose
the screen image is called the 'resolution'. This number
shows the accuracy of the display. A high resolution is good
for performing multiple tasks as more image information can
be shown on the screen.
Example: If the resolution is 1360(1920) x 768(1080), this
means the screen is composed of 1360(1920) horizontal
dots (horizontal resolution) and 768(1080) vertical lines
(vertical resolution).
SRS TS XT
Multiple
(MDC)
Display
This feature outputs sonorous and vivid 3D sound as for 5.1
channel speaker sound but through a 2-channel speaker. It
has a good effect when stereo signals are input.
Control
A Multiple Display Control (MDC) is an application allowing
various displays to be easily and simultaneously operated
on a PC. RS-232C, a standard of serial communication, is
used for communicating between a PC and a display.
Correct Disposal
Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking on the product, accessories or literature
indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not
be disposed of with other household waste at the end
of their working life. To prevent possible harm to the
environment or human health from uncontrolled
waste disposal, please separate these items from
other types of waste and recycle them responsibly to
promote the sustainable reuse of material resources.
Household users should contact either the retailer
where they purchased this product, or their local government office, for details of where and how they can
take these items for environmentally safe recycling.
Business users should contact their supplier and
check the terms and conditions of the purchase con-
Appendix
Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
tract. This product and its electronic accessories
should not be mixed with other commercial wastes
for disposal.
Correct disposal of batteries in this product - Europe only
(Applicable in the European Union and other European countries with separate battery return systems.)
This marking on the battery, manual or packaging indicates that the batteries in this product should not
be disposed of with other household waste at the end
of their working life. Where marked, the chemical
symbols Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the reference
levels in EC Directive 2006/66. If batteries are not
properly disposed of, these substances can cause
harm to human health or the environment.
To protect natural resources and to promote material
reuse, please separate batteries from other types of
waste and recycle them through your local, free battery return system.
Note
The rechargeable battery incorporated in this product is not user replaceable. For information
on its replacement, please contact your service provider.
Authority
Information in this document is subject to change without notice.
© 2009 Samsung Electronics Co., Ltd. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co., Ltd. is strictly forbidden.
Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental
or consequential damages in connection with the furnishing, performance, or use of this material.
Samsung is the registered trademark of Samsung Electronics Co., Ltd.; Microsoft, Windows
and Windows NT are registered trademarks of Microsoft Corporation; VESA, DPM and DDC
are registered trademarks of Video Electronics Standard Association; the ENERGY STAR®
name and logo are registered trademarks of the U.S. Environmental Protection Agency
(EPA).As an ENERGY STAR® Partner, Samsung Electronics Co., Ltd. has determined that
this product meets the ENERGY STAR® guidelines for energy efficiency. All other product
names mentioned herein may be the trademarks or registered trademarks of their respective
owners.
Appendix
Download PDF