Samsung | TX-WN | Samsung Thin Client Box TX-WN Benutzerhandbuch

User Manual
TX-WN
The color and the appearance may differ depending on
the product, and the specifications are subject to
change without prior notice to improve the performance.
BN46-00302A-01
Table Of Contents
BEFORE USING THE
PRODUCT
PREPARATIONS
USING "WINDOWS
EMBEDDED STANDARD 7"
(TX-WN)
5
Copyright
6
6
Icons used in this manual
Symbols for safety precautions
7
Securing the Installation Space
7
Precautions for storage
8
Safety Precautions
8
9
11
Electricity and Safety
Installation and Safety
Operation and Safety
15
Checking the Contents
15
16
Removing the Packaging
Checking the Components
18
Parts
18
20
Front view
Reverse Side
21
Installation
21
22
Attaching the cradle
Anti-theft Lock
23
What is "Windows Embedded Standard
7" Client?
24
Connection to Use "Windows Embedded
Standard 7"
24
25
25
25
26
26
27
Before Connecting
Connection Using the DVI Cable
Connecting a Microphone
Connecting to Headphones
LAN Connection
Connecting USB Devices
Connecting the Power
Table Of Contents
2
Table Of Contents
28
Using "Windows Embedded Standard 7"
28
28
29
36
37
Logon
"Windows Embedded Standard 7" Desktop
Programs
Configuring Utilities
Recover the System
39
MagicRMS Pro
39
39
40
40
40
40
40
About MagicRMS Pro
Components
MagicRMS Pro Server
MagicRMS Pro Database
MagicRMS Pro Console
PXE
MagicRMS Pro Agent
41
Connecting to a wireless LAN using
Windows
42
Successful wireless LAN connection
42
Failed wireless LAN connection
42
42
43
Failed to connect to a wireless LAN
Internet connection is not available
An AP is found but Internet access is not
available
TROUBLESHOOTING
GUIDE
44
Requirements Before Contacting
Samsung Customer Service Center
44
Check the following.
SPECIFICATIONS
45
General
46
Power consumption
47
Contact SAMSUNG WORLD WIDE
WIRELESS NETWORK
(OPTIONAL)
APPENDIX
Table Of Contents
3
Table Of Contents
53
Responsibility for the Pay Service (Cost
to Customers)
53
53
53
Not a product defect
A Product damage caused by customer's fault
Others
54
Correct Disposal
54
Correct Disposal of This Product (Waste
Electrical & Electronic Equipment)
Correct disposal of batteries in this product
54
INDEX
Table Of Contents
4
Before Using the Product
Copyright
The contents of this manual are subject to change without notice to improve quality.
© 2012 Samsung Electronics
Samsung Electronics owns the copyright for this manual.
Use or reproduction of this manual in parts or entirety without the authorization of Samsung Electronics is
prohibited.
The SAMSUNG logo is a registered trademark of Samsung Electronics.
Microsoft and Windows are registered trademarks of Microsoft Corporation.
VESA, DPM and DDC are registered trademarks of the Video Electronics Standards Association.
z
An administration fee may be charged if either
†
(a) an engineer is called out at your request and there is no defect in the product
(i.e. where you have failed to read this user manual).
†
(b) you bring the unit to a repair centre and there is no defect in the product
(i.e. where you have failed to read this user manual).
z
The amount of such administration charge will be advised to you before any work or home visit is
carried out.
Before Using the Product
5
Before Using the Product
Icons used in this manual
The following images are for reference only. Real-life situations may
differ from what is shown in the images.
Symbols for safety precautions
Warning
A serious or fatal injury may result if instructions are not followed.
Caution
Personal injury or damage to properties may result if instructions are
not followed.
Activities marked by this symbol are prohibited.
Instructions marked by this symbol must be followed.
Before Using the Product
6
Before Using the Product
Securing the Installation Space
Ensure some space around the product for ventilation. An internal temperature rise may cause fire and
damage the product. Be sure to allow the amount of space as shown below or greater when installing
the product.
z
The exterior may differ depending on the product.
z
This product can be installed in portrait or landscape orientation.
10 cm
10 cm
(3.0)
(2.0)
10 cm
10 cm
10 cm
Precautions for storage
For information on how to clean the inside of the product, contact the service center first.
(A service fee will be charged.)
Before Using the Product
7
Before Using the Product
Safety Precautions
The following images are for reference only. Real-life situations may differ from what is shown in
the images.
Electricity and Safety
Warning
Do not use a damaged power cable or plug, or a loose power socket.
z
An electric shock or fire may result.
Do not plug many products into the same power socket.
z
Otherwise, the socket may overheat and cause a fire.
Do not touch the power cable with wet hands.
z
Otherwise, an electric shock may result.
Insert the power cable all the way in so it is not loose.
z
An unstable connection may cause a fire.
!
Ensure you connect the power cable to a grounded power socket. (type 1
insulated devices only).
!
z
An electric shock or injury may result.
Do not bend or pull the power cable with force. Do not weigh the power cable
down with a heavy object.
z
A damaged power cord may cause an electric shock or fire.
Do not place the power cable or product near heat sources.
z
An electric shock or fire may result.
If the power cable pins or power outlet is covered with a foreign substance (dust,
etc.), wipe it off using a dry cloth.
!
z
Otherwise, a fire may result.
Before Using the Product
8
Before Using the Product
Caution
Do not unplug the power cable when the product is in use.
z
The product may become damaged by an electric shock.
Do not use the power cable for products other than authorized products supplied
by Samsung.
z
!
An electric shock or fire may result.
Keep the power socket where the power cable is connected unobstructed.
z
If any problem occurs in the product, unplug the power cable to completely
cut the power to the product.
!
z
You cannot cut the power off completely using only the power button on the
product.
Hold the plug when disconnecting the power cable from the power socket.
z
An electric shock or fire may result.
!
Installation and Safety
Warning
DO NOT PLACE CANDLES, INSECT REPELLANTS OR CIGARETTES ON TOP
OF THE PRODUCT. DO NOT INSTALL THE PRODUCT NEAR HEAT SOURCES.
z
Otherwise, a fire may result.
Avoid installing the product in a narrow space with bad ventilation, such as a
bookshelf or wall closet.
z
Otherwise, a fire may result due to an increased internal temperature.
Keep the plastic packaging bag for the product in a place that cannot be reached
by children.
!
z
Children may suffocate.
Before Using the Product
9
Before Using the Product
Do not install the product on an unstable or vibrating surface (insecure shelf,
sloped surface, etc.).
z
The product may fall and break or cause a personal injury.
z
Using the product in an area with excess vibration may damage the product
or cause a fire.
Do not install the product in a vehicle or a place exposed to dust, moisture (water
drips, etc.), oil, or smoke.
z
!
An electric shock or fire may result.
Do not expose the product to direct sunlight, heat, or a hot object such as a
stove.
z
Otherwise, the product lifespan may be reduced, or a fire may result.
Do not install the product within the reach of young children.
z
The product may fall and injure children.
Edible oil, such as soybean oil, can damage or deform the product. Do not install
the product in a kitchen or near a kitchen counter.
Caution
Take care not to drop the product when moving it.
z
Otherwise, product failure or personal injury may result.
!
Put down the product carefully.
z
The product may fall and break or cause a personal injury.
!
Before Using the Product
10
Before Using the Product
SAMSUNG
!
Installing the product in an unusual place (a place exposed to a lot of fine
particles, chemical substances or extreme temperatures, or an airport or train
station where the product should operate continuously for an extended period of
time) may seriously affect its performance.
z
Be sure to consult Samsung Customer Service Center (page 47) before
installation if you want to install the product at such a place.
Do not leave or install the product on the floor.
z
Abrupt force such as kicking or extra weight such as stepping on the
product may cause a product failure or personal injury.
Operation and Safety
Warning
High voltage runs through the product. Do not attempt to disassemble, repair, or
modify the product on your own.
z
An electric shock or fire may result.
z
Contact Samsung Customer Service Center (page 47) for repair.
Before moving the product, turn off the power and disconnect the power cable
and all other connected cables.
!
z
Otherwise, the power cord may be damaged and a fire or electric shock may
result.
If the product generates a strange noise, a burning smell, or smoke, remove the
power cable immediately and contact Samsung Customer Service Center
(page 47).
!
z
An electric shock or fire may result.
Ensure children do not sit on the product or kick the product.
z
The product may fall, and your child may become injured or seriously
harmed.
If the product falls or the exterior is damaged, power off the product, remove the
power cable, and contact Samsung Customer Service Center (page 47).
z
Otherwise, an electric shock or fire may result.
Do not sit on the product.
z
The product housing or connectors may get damaged or personal injury may
result.
Before Using the Product
11
Before Using the Product
During a lightning or thunderstorm, power off the product and remove the power
cable.
z
!
An electric shock or fire may result.
Do not drop objects on the product or apply impact.
z
An electric shock or fire may result.
!
Do not move the product holding only by the power cable or a signal cable.
z
Otherwise, the cable may be damaged and product failure, an electric shock
or fire may result.
If a gas leakage is found, do not touch the product or power cable. Also, ventilate
the area immediately.
!
GAS
z
Sparks can cause an explosion or fire.
Do not use or keep combustible spray or an inflammable substance near the
product.
z
!
100
An explosion or fire may result.
Do not insert metallic objects such as a chopstick, coin or hair pin into the vent or
ports of the product. Do not insert inflammable objects such as paper or a match
into the vent or ports of the product.
z
If water or any foreign substance enters the product, be sure to power off the
product, remove the power cable, and contact Samsung Customer Service
Center (page 47).
z
Product failure, an electric shock or fire may result.
Do not place objects containing liquid (vases, pots, bottles, etc) or metallic
objects on top of the product.
z
If water or any foreign substance enters the product, be sure to power off the
product, remove the power cable, and contact Samsung Customer Service
Center (page 47).
z
Product failure, an electric shock or fire may result.
Before Using the Product
12
Before Using the Product
Caution
Disconnect the power cable from the power socket if you do not plan on using
the product for an extended period of time (vacation, etc.).
!
z
Otherwise, a fire may result from accumulated dust, overheating, an electric
shock, or electric leakage.
Do not put DC power adapters together.
z
Otherwise, a fire may result.
Remove the plastic bag from the DC power adapter before you use it.
z
Otherwise, a fire may result.
Do not let water enter the DC power adapter or get the adapter wet.
z
An electric shock or fire may result.
z
Avoid using the product outdoors where it can be exposed to rain or snow.
z
Be careful not to get the DC power adapter wet when you wash the floor.
Do not put the DC power adapter near to any heating apparatus.
z
Otherwise, a fire may result.
Keep the DC power adapter in a well-ventilated area.
!
Do not use humidifiers or stoves around the product.
z
An electric shock or fire may result.
Store the small accessories used with the product out of reach of children.
!
Before Using the Product
13
Before Using the Product
Do not place heavy objects on the product.
z
Product failure or personal injure may result.
Do not increase the volume too high when using headphones (earphones).
z
Sound particularly at a higher volume could potentially affect long-term
hearing.
Before Using the Product
14
1
1.1
Preparations
Checking the Contents
1.1.1 Removing the Packaging
1
Open the packaging box. Be careful not to damage the product when you open the packaging with
a sharp instrument.
2
Remove the styrofoam from the product.
3
Check the components and remove the styrofoam and plastic bag.
4
z
The appearance of actual components may differ from the image shown.
z
This image is for reference only.
Store the box in a dry area so that it can be used when moving the product in the future.
1 Preparations
15
1
Preparations
1.1.2 Checking the Components
z
Contact the dealer from whom you purchased the product if any item is missing.
z
The appearance of the components and items sold separately may differ from the image shown.
Components
Quick setup guide
Warranty card
User Manual
(Not available in some
locations)
Product
Power cable
DC power adapter
Cradle
Components may vary depending on the country.
1 Preparations
16
1
Preparations
Items sold separately
The following items can be purchased at your nearest retailer.
LAN cable
USB cable
HDMI-DVI cable
DVI cable
RS232C cable
DVI-RGB cable
Mouse (USB)
Keyboard
MIC
Headphone
1 Preparations
17
1
1.2
Preparations
Parts
1.2.1 Front view
The color and shape of parts may differ from what is shown. Specifications are subject to change
without notice to improve quality.
A
(3.0)
(2.0)
(3.0)
(2.0)
Ports
Description
Power on or off the product.
Connect to a microphone.
Connect to an audio output device such as headphones.
Connect to a USB device.
z
Connect a device that supports USB 3.0 to the USB 3.0 port for
optimal performance.
z
Keyboard and mouse devices are required to connect to USB
2.0.
z
Wake up function is not supported on USB 3.0 ports.
(3.0)
1 Preparations
18
1
Preparations
Ports
Description
(2.0)
Connect to a USB device.
A
Speaker
1 Preparations
19
1
Preparations
1.2.2 Reverse Side
The color and shape of parts may differ from what is shown. Specifications are subject to change
without notice to improve quality.
(2.0)
SERIAL
LAN
DVI-I OUT
(2.0)
SERIAL
DVI-D OUT
DC 14V
LAN
DVI-I OUT
Ports
DVI-D OUT
DC 14V
Description
(2.0)
Connect to a USB device.
SERIAL
Connect to a device that supports an RS-232C connection
(interface).
LAN
Connect to a network using the LAN cable.
Connect to the monitor using the DVI cable.
DVI-I OUT
The port supports both digital and analog output. To use an
analog output, connect a device to the port using a DVI-RGB
cable (sold separately).
DVI-D OUT
Connect to the monitor using the DVI cable.
The port only supports digital output.
DC 14V
Connect to the DC power adapter.
1 Preparations
20
1
1.3
Preparations
Installation
1.3.1 Attaching the cradle
z
The color and shape of parts may differ from what is shown. Specifications are subject to change
without notice to improve quality.
z
This product can be installed in portrait or landscape orientation.
Vertical Type
Horizontal Type
(3.0)
(2.0)
(3.0)
(2.0)
1 Preparations
21
1
Preparations
1.3.2 Anti-theft Lock
An anti-theft lock allows you to use the product securely even in public places. The locking device shape
and locking method depend on the manufacturer. Refer to the user guide provided with your anti-theft
locking device for details. The lock device is sold separately.
DVI-D OUT
D
To lock an anti-theft locking device:
1
2
3
4
Fix the cable of your anti-theft locking device to a heavy object such as a desk.
Put one end of the cable through the loop on the other end.
Insert the locking device into the anti-theft lock slot at the back of the product.
Lock the locking device.
z
An anti-theft locking device can be purchased separately.
z
Refer to the user guide provided with your anti-theft locking device for details.
z
Anti-theft locking devices can be purchased at electronics retailers or online.
1 Preparations
22
2
2.1
Using "Windows Embedded Standard 7" (TXWN)
What is "Windows Embedded Standard 7" Client?
The Microsoft Windows Embedded Standard 7 (WES7) client uses the Microsoft Windows
Embedded Standard 2011 OS. When the WES client is connected to a server where Citrix
XenDesktop, VMWare View Client, or Microsoft Remote Desktop Connection service is available,
the keyboard, mouse, audio/video, and display data will be forwarded to the client through the network
between the client and server.
Connectable Servers
z
A Citrix XenDesktop Server
†
Microsoft Windows 2000/2003/2008 Server where the Terminal Service and Citrix
XenServer are installed
z
A VMWare View Client Server
†
Microsoft Windows 2000/2003/2008 Server where the Terminal Service and VMWare
Server are installed
z
A Microsoft RDP (Remote Desktop Protocol) Server
†
Microsoft Windows 2000/2003/2008 Server where the Terminal Services are installed
†
Microsoft Windows 7 Professional
This manual describes the functions provided by the WES Client. However, it does not explain general
functionalities of WES. For more general information on Windows 7, refer to Windows 7 Help provided
by Microsoft.
2 Using "Windows Embedded Standard 7" (TX-WN)
23
2
2.2
Using "Windows Embedded Standard 7" (TXWN)
Connection to Use "Windows Embedded Standard 7"
2.2.1 Before Connecting
Pre-connection Checkpoints
z
Before connecting a source device, read the user manual provided with it.
The number and locations of ports on source devices may differ from device to device.
z
Do not connect the power cable until all connections are completed.
Connecting the power cable during connection may damage the product.
z
Check the types of ports at the back of the product you want to connect.
z
The port names may vary depending on the monitor.
z
For details on how to change the input source for your monitor, refer to the monitor user manual.
z
The monitor images in this manual are for reference only. Monitor is sold separately.
2 Using "Windows Embedded Standard 7" (TX-WN)
24
2
Using "Windows Embedded Standard 7" (TXWN)
2.2.2 Connection Using the DVI Cable
DVI-I OUT
1
DVI IN
Connect the DVI cable to [DVI IN] at the back of the monitor and [DVI-I OUT] or [DVI-D OUT] on the
product.
z
The [DVI-I OUT] port supports both digital and analog output. To use an analog output, connect a
device to the port using a DVI-RGB cable (sold separately).
z
The [DVI-D OUT] port only supports digital output.
2.2.3 Connecting a Microphone
1
Connect the microphone to [
] on the front of the product.
2.2.4 Connecting to Headphones
1
Connect the headphones to [
] on the front of the product.
2 Using "Windows Embedded Standard 7" (TX-WN)
25
2
Using "Windows Embedded Standard 7" (TXWN)
2.2.5 LAN Connection
LAN
1
Connect the LAN cable to the [LAN] port at the back of the product.
2.2.6 Connecting USB Devices
(3.0)
(2.0)
1
Connect USB devices to 3.0 or 2.0 of the product.
z
Connect a device that supports USB 3.0 to the USB 3.0 port for optimal performance.
z
Wake up function is not supported on USB 3.0 ports.
z
Keyboard and mouse devices are required to connect to USB 2.0.
2 Using "Windows Embedded Standard 7" (TX-WN)
26
2
Using "Windows Embedded Standard 7" (TXWN)
2.2.7 Connecting the Power
(2.0)
SERIAL
LAN
DVI-I OUT
VI-I OUT
DVI-D OUT
DC 14V
DVI-D OUT
DC 14V
Connect the power cable to the DC power
adapter. Connect the DC power adapter to
[DC 14V] on the product.
Connect the power cable to the power outlet
and turn on the switch on the DC power
adapter.
z
The color and shape of parts may differ from what is shown. Specifications are subject to change
without notice to improve quality.
z
For details on how to connect the power cable to the monitor, refer to the monitor user manual.
2 Using "Windows Embedded Standard 7" (TX-WN)
27
2
2.3
Using "Windows Embedded Standard 7" (TXWN)
Using "Windows Embedded Standard 7"
2.3.1 Logon
When the client starts, you can logon to the server by entering your username and password. By default,
you are automatically logged in with an Administrator account and a blank password.
2.3.2 "Windows Embedded Standard 7" Desktop
Standard User
When logged on as a Standard User, there are many restrictions that protect the system from incorrect
user actions. You cannot access the system drives and there are restrictions on configuring properties for
them. To configure the client’s advanced and detailed settings, log on as an administrator.
It is recommended to create Standard User accounts for general users that use the product.
Administrator
The Administrator account has privileges to configure the system settings and install/uninstall software.
If it is required to restrict access privileges for security or administrator privileges are not needed, it is
recommended to create Standard User accounts for general users.
The audio volume icon, Enhanced Write Filter status icon, and system time are displayed on the
Administrator Taskbar. The Administrator privilege is required for adding and removing programs.
Log off, Restart, Shut down
z
To log off the current session, shut down or restart your client, use the Start menu. [Start
Shut
down]. The Shut Down Windows dialog box is displayed. To shut down the client immediately,
select [Start
Shut down]. To select Log off, Restart, etc., move the mouse over the
▶ icon
next to [Shut down]. Alternatively, you can perform Log off or Shut down using the Windows
Security Dialog box by pressing [Ctrl + Alt + Del]. If ‘Force Auto Log on’ is activated, you will be
immediately logged on after each log off.
z
The Client Log off, Restart and Shut down take effect on the operations of the EWF (Enhanced
Write Filter). To keep the changed system configuration, you must save a cache for the current
system session into flash memory. Failing to do so will cause the changed configuration to be lost
when the client is shut down or restarted. (In the case of logging off, the configuration is
remembered when loggin in again.) For more information on the Enhanced Write Filter, refer to the
Program Help.
2 Using "Windows Embedded Standard 7" (TX-WN)
28
2
Using "Windows Embedded Standard 7" (TXWN)
2.3.3 Programs
Remote Desktop Connection
You can control a running terminal server or another computer (Windows 95 or later) remotely through a
remote desktop connection.
z
Remote Desktop
Windows 7 Professional or Windows 2000/2003/2008 Server must be installed on the
†
computer to be controlled remotely. This computer is called a host.
A remote computer running on an operating system later than Windows 95 is required. This
†
remote computer is called a client. The client software for the remote desktop connection must be
installed on the client.
You must also be connected to the Internet. A broadband Internet connection is good for high
†
performance. However, because the remote desktop transmits a minimum set of data including
the display data and keyboard data to control the host remotely, a broadband Internet
connection is not required. You can run a remote desktop on a low bandwidth Internet
connection.
When running a remote desktop on Windows 7 Professional, you cannot use the operating
system of your computer.
z
Enabling Your Computer as the Host
You must enable the Remote Desktop feature to control it from another computer. You must be
logged on as an Administrator or a member of the Administrators group to enable Remote
Desktop on your computer. Follow these steps:
1
2
Open the System folder in the Control Panel.
Go to [Start
Control Panel
System and Security
System], and click Remote
settings.
3
If you want to block other PCs from accessing your PC using Remote Desktop or
RemoteApp, select “Don't allow connections to this computer”.
z
To allow a remote PC to access your PC using any version of Remote Desktop or RemoteApp,
select "Allow connections from computers running any version of Remote Desktop (less
secure)". This option is suitable if you do not know the Remote Desktop Connection version
being used on other PCs. Note that this option is less secure than the next option (option 3).
z
To allow a remote PC to access your PC using a Remote Desktop or RemoteApp version
requiring a network level authentication, select "Allow connections only from computers
2 Using "Windows Embedded Standard 7" (TX-WN)
29
2
Using "Windows Embedded Standard 7" (TXWN)
running Remote Desktop with Network Level Authentication (more secure)" to run Remote
Desktop using network-level authentication.
z
Start a Remote Desktop Session on the Client
Once you have enabled your host computer to allow remote connections and installed the client
software on a Windowsbased client computer, you are ready to start a Remote Desktop session.
You must first establish a virtual private network connection or remote access service connection
from your client computer to your host computer. To connect to another remote desktop, follow the
instructions below.
1
Go to [Start
All Programs
Accessories
Remote Desktop Connection] or double-
click the Remote Desktop Connection icon to open Remote Desktop Connection.
2
Enter the host computer name. You can configure detailed settings by clicking the Options
button.
2 Using "Windows Embedded Standard 7" (TX-WN)
30
2
Using "Windows Embedded Standard 7" (TXWN)
3
Options
- General : Enter in the login information for the host computer. To log in automatically, enter in
the user name and password.
- Display : The Remote Desktop Connection sends and receives compressed screen data. If
you set the resolution and color quality to the high option, the speed may become slow.
- Local Resources : Specify whether to use the hard disks and ports.
2 Using "Windows Embedded Standard 7" (TX-WN)
31
2
Using "Windows Embedded Standard 7" (TXWN)
- Programs : Select an application and specify the folder where you want to run the application
when a connection is established to the host PC.
- Experience : Specify the connection speed and the menu items you want to use on the
remote PC connected. The settings specified will be shared with the host PC.
2 Using "Windows Embedded Standard 7" (TX-WN)
32
2
Using "Windows Embedded Standard 7" (TXWN)
- Advanced : Protect your personal information when a connection is established.
4
5
Click Connect. The Log On to Windows dialog box appears.
In the “Log On to Windows” dialog box, type your username, password, and domain (if
required), and then click OK. The Remote Desktop window will open and you will see the
desktop settings, files, and programs that are on the host computer.
For more information on Remote Desktop Connections, visit the Microsoft web site.
2 Using "Windows Embedded Standard 7" (TX-WN)
33
2
Using "Windows Embedded Standard 7" (TXWN)
Internet Explorer
A WES Client includes Internet Explorer. This program is permitted for all users. Microsoft website.
For more information on Internet Explorer, visit the Microsoft website.
Enhanced Write Filter (EWF)
Enhanced Write Filter (EWF) protects a flash volume from write access and consequently, preserves
the durability of the flash device. EWF provides read and write access through a cache to the client
instead of allowing direct access to a flash volume.
If EWF is activated, data is not stored to the flash. The data stored in the cache is only effective while the
client is operating. The cached data will be lost when restarting or shutting down your client. Therefore, to
store the data written to the registry, favorites and cookie folders, etc., the content stored in the cache
should be transferred to the flash. An error message is displayed when it is not possible to write to the
cache due to a lack of memory. If this message is displayed, you have to deactivate EWF to flush the
EWF cache. The user can double-click the EWF icon on the tray at the bottom right of the screen to call
the EWF Manager. A user can also change the EWF configuration by entering EWF management
commands at the command prompt. This task requires the Administrator privilege.
z
Enable write filter and restart the system.
If the EWF is disabled, enable it. If this item is selected, the cache is flushed and the EWF is enabled.
After restarting your computer, the configurations and file system information for the client are written
to a cache. You can also perform this operation by entering “ewfmgr.exe c: -enable” at the
command prompt and restarting your computer.
z
Disable write filter and restart the systems.
This item is activated when the EWF is running. If this item is selected, the current states of the client
(saved in a cache) are saved to a flash volume and the EWF is disabled. After restarting your
computer, the configurations and file system information for the client are written to a flash volume.
2 Using "Windows Embedded Standard 7" (TX-WN)
34
2
Using "Windows Embedded Standard 7" (TXWN)
You can also perform this operation by entering “ewfmgr.exe c: -commitanddisable” at the
command prompt and restarting your computer.
z
Commit changes to disk.
This item is activated when the EWF is running. If this item is selected, the current states of the client
(saved in a cache) are saved to a flash volume. However, the state of EWF will not be changed. You
can also perform this operation by entering “ewfmgr.exe c: -commit” at the command prompt.
You can view the configurations for the protected volumes by entering “ewfmgr.exe c:” at the
command prompt.
File-Based Write Filter (FBWF)
The File-Based Write Filter (FBWF) protects the memory of the client from being overwritten by any
unauthorized user. By restricting excessive writing into the memory, the FBWF allows you to use the
client for a long time. If you request I/O, the FBWF has the client perform its operations using the cache
instead of the memory so that the memory can be protected.
The data saved in the cache is preserved while the client operates normally. It is removed when it is
restarted or exited. To save the changes, you should write the relevant file onto the disk using the commit
command. If you don’t know which file is changed, disable the FBWF, change it, and enable it again.
You can control the FBWF using the various options of the command at a command prompt.
z
FBWF Configuration
†
Current FBWF status : Displays the current status of the FBWF (Enabled or Disabled).
†
Boot command : Displays the FBWF command that will be performed at the next boot-up.
†
RAM Used by FBEF : Displays the size of the RAM the FBWF is using. If the current status is
set to "Disabled", the used memory is displayed as 0 KB.
†
z
Threshold : Displays the maximum size of the RAM that the FBWF can use.
FBWF Command
†
Enable FBWF and reboot the system : Enables the disabled FBWF and restarts the client. If
the client is not restarted, only the boot command is changed to BWF_ENABLE and the current
status is not changed.
†
Disable FBWF and reboot the system : Disables the enabled FBWF and restarts the client. If
the client is not restarted, only the boot command is changed to FBWF_DISABLE and the
current status is not changed.
†
Commit files : Even if the disks are protected by the FBWF, you can add or delete the files you
want to save on them. To write the changes onto the disk, click the [Write the changes to the
disk] button.
z
Session Status
†
Current session : Displays the volumes being protected by the FBWF and a list of the folders
and files on those volumes that are excepted from protection by the FBWF.
2 Using "Windows Embedded Standard 7" (TX-WN)
35
2
Using "Windows Embedded Standard 7" (TXWN)
†
Next session : Select the volumes that will be protected by the FBWF when the client is
booted up next time. Also, select the folders and files that you want to except from protection
by the FBWF.
Windows Media Player
The WES Client includes Windows Media Player 12. With Windows Media Player, you can play audio
and video files on a website.
2.3.4 Configuring Utilities
Local Drive
z
C Drive
The C drive is used for the system. The client OS will not operate if space available on the system
drive is not sufficient. Ensure sufficient space is available on the C drive. EWF can help maintain
available space by preventing the C drive being written to directly.
z
Saving Files
Your client uses a fixed size of flash memory. Therefore, it is better to save files to the server rather
than to your client.
Mapping a Network Drive
The Administrator can map a folder to a network drive. To keep the mapping information after restarting
the client, take note of these directions carefully.
z
Select the Reconnect at logon checkbox in the Map Network Drive dialog box.
z
If the EWF or FBWF is enabled, the changes are saved on the disk.
2 Using "Windows Embedded Standard 7" (TX-WN)
36
2
Using "Windows Embedded Standard 7" (TXWN)
2.3.5 Recover the System
Overview
The WES client provides a feature that restores the system to the last backup or default factory settings
in the occurrence of a critical system issue during operation. You can back up an OS image which is
working normally to USB memory or the PXE server. You can revert to a backed up image when your
client has one of these problems:
z
When a system file is deleted accidentally or is corrupted
z
When the client computer is unstable or there is a problem with a device driver
z
When problems occur, after installing a new program or device
z
When the client computer is infected with a virus
z
When Windows Embedded Standard fails to start When a system file is deleted accidentally or is
corrupted
How to Recover the System
z
Recovery Using USB Memory
By following these steps, you can save all necessary files to USB memory, and boot up with the
backed up system on the USB memory and recover the system.
1
2
Format the USB memory device to enable the system to boot.
Save the Windows Embedded Standard image and the Backup/Recovery Utility which will be
recovered later to your USB memory.
3
4
Boot up with the USB memory.
Recover the system using the Windows Embedded Standard image and the Backup/
Recovery Utility in the USB memory.
z
Recovery Using Network Booting
This method is provided through the PXE (Preboot eXecution Environment) server. The PXE
sever provides a client/server interface based on TCP/IP, DHCP, and TFTP. It allows an
administrator at a remote location to configure and boot the operating system onto a client over a
network.
†
Implement a PXE server.
†
Save the Windows Embedded Standard image and the Backup/Recovery Utility which will be
recovered later onto the PXE server.
†
Boot the client via the network.
†
Recover the system using the Windows Embedded Standard image and the Backup/
Recovery Utility saved on the PXE server via the network.
For more information, refer to the PXE Server User Manual.
2 Using "Windows Embedded Standard 7" (TX-WN)
37
2
Using "Windows Embedded Standard 7" (TXWN)
z
Using the Standalone restore solution
Restore the system using a restore image saved on the product.
1
After the power is connected, press the Home key immediately after the system starts during
boot to enter the boot menu.
2
3
4
5
Select the Recovery Mode menu and press the P key to enter "admin" which is the password.
Run the Recovery Mode menu by pressing the Enter key.
If the PROMPT "root@xxxxx:/#" appears, enter "recovery" to restore the system.
If PROMPT appears after a message informing that the system is successfully restored, run the
reboot command to restart the system.
DISK is configured as follows. Deleting or changing partitions may disable booting or the
Standalone restore solution.
BOOT_AGENT
WES7
BACKUP
Drive Letter is not defined
C:
Drive Letter is not defined
Data saved by the user and customized settings are deleted after a system restore.
2 Using "Windows Embedded Standard 7" (TX-WN)
38
2
2.4
Using "Windows Embedded Standard 7" (TXWN)
MagicRMS Pro
2.4.1 About MagicRMS Pro
The MagicRMS Pro program can be used to remotely control a Samsung network monitor. The design
of the user-oriented interface makes it easy and convenient to use.
Using MagicRMS Pro, you can schedule a task to be performed at a specified time on a network
monitor.
Also, you can manage multiple network monitors efficiently by grouping or filtering them according to
specific conditions.
To use the MagicRMS Pro Solution or MagicRMS Pro Agent and to view the user guide, visit
www.samsunglfd.com. Go to Support>Download Center, and search for MagicRMS to download.
Open source license notice
In the case of using open source software, Open Source licenses are available on the MagicRMS Pro
Agent.
Open Source License Notice is written only English.
2.4.2 Components
MagicRMS Pro consists of MagicRMS Pro Server, MagicRMS Pro Database, MagicRMS Pro
Console, and PXE. MagicRMS Pro manages network monitors by interacting with the MagicRMS Pro
Agent.
MagicRMS Pro Server, Database, and Console refer to Server, Database, and Console
respectively. MagicRMS Pro Agent refers to Agent.
2 Using "Windows Embedded Standard 7" (TX-WN)
39
2
Using "Windows Embedded Standard 7" (TXWN)
2.4.3
MagicRMS Pro Server
MagicRMS Pro Server is a core component of MagicRMS Pro. The Server connects to Database and
Console and sends a command to perform a task requested by the user to network monitors where the
Agent is installed.
A task requested from the Console is saved in the Database. The saved task is forwarded to the Agent
over the Server and performed on the network monitors.
2.4.4
MagicRMS Pro Database
MagicRMS Pro Database keeps information needed to manage network monitors.
2.4.5
MagicRMS Pro Console
Manage network monitors and organize task requests using the Console.
2.4.6
PXE
PXE is a standard protocol that allows the Server and Client to communicate to enable the Client to boot
over a network using DHCP and TFTP.
Booting the system over a network enables a Diskless booting where the system can be operated
regardless of the operating system. It also allows the system operating system to be restored or backed
up over the network.
2.4.7
MagicRMS Pro Agent
MagicRMS Pro Agent is installed on a network monitor to perform tasks requested from the server and
send the network monitor information to the server periodically.
For further details on how to use the MagicRMS Pro Agent, see help for MagicRMS Pro Agent.
2 Using "Windows Embedded Standard 7" (TX-WN)
40
3
3.1
Wireless Network (optional)
Connecting to a wireless LAN using Windows
If there is an AP nearby, conveniently connect to a wireless LAN using the wireless LAN access method
provided by Windows.
1
Click the Network connection
icon on the task bar. Select an AP to connect from the displayed
list of available APs. The Connect button appears.
AP list
2
Click Connect. If the network key is configured for the AP to connect, enter the network key and
click Connect.
To obtain the network key, contact the network manager.
3
Use the wireless network as desired.
3 Wireless Network (optional)
41
3
3.2
Wireless Network (optional)
Successful wireless LAN connection
The wireless LAN icon on the task bar as shown below indicates that it is correctly connected to the
Internet.
3.3
Failed wireless LAN connection
3.3.1 Failed to connect to a wireless LAN
The "
" mark in place of the wireless LAN icon on the task bar indicates that the wireless LAN is
disabled or there is no AP nearby. The mark can also means that the wireless LAN is disconnected.
3.3.2 Internet connection is not available
The
mark in place of the wireless LAN icon on the task bar indicates that Internet access is not
available. In this case, make sure the network address is correct. Contact the network manager.
If required, configure the network address again.
3 Wireless Network (optional)
42
3
Wireless Network (optional)
3.3.3 An AP is found but Internet access is not available
This issue may occur when a higher priority is given to a wireless LAN AP with low signal strength.
Click an AP with higher signal strength and try again.
Currently connected AP,
signal strength is low
AP that has
high signal strength
3 Wireless Network (optional)
43
4
4.1
Troubleshooting Guide
Requirements Before Contacting Samsung Customer
Service Center
4.1.1 Check the following.
Installation issue
The product cannot power on.
Check that the power cable is connected
properly.
(Refer to "2.2.7 Connecting the Power")
Sound issue
There is no sound.
Check the connection of the audio cable or adjust
the volume.
Check the volume.
The volume is too low.
Adjust the volume.
If the volume is still low after turning it up to the
maximum level, adjust the volume in the audio
settings program.
4 Troubleshooting Guide
44
5
5.1
Specifications
General
Model Name
TX-WN
Power Supply
This product uses 100 to 240V. Refer to the label at the back of
the product as the standard voltage can vary in different countries.
Video signal
DVI-I OUT, DVI-D OUT
Server connector
LAN, Wi-Fi
Speaker
1Wx2
Dimensions
(W x H x D) /
With cradle
Weight
Vertical Type : 91.8 X 217.8 X 166.3 mm / 3.6 X 8.6 X 6.5 inches /
907g / 2.0 lb
Horizontal Type : 210 X 54.8 X 122 mm / 8.3 X 2.2 X 4.8 inches /
907g / 2.0 lb
Without cradle
210 X 47.5 X 122 mm / 8.3 X 1.9 X 4.8 inches /
867g / 1.9 lb
Cradle
91.8 X 13 X 166.3 mm / 3.6 X 0.5 X 6.5 inches /
40g / 0.09 lb
USB
USB 2.0 x 4 (Down stream)
USB 3.0 x 2 (Down stream)
Environmental
considerations
Operating
Temperature : 50˚F ~ 104˚F (10˚C ~ 40˚C)
Humidity : 10 % – 80 %, non-condensing
Storage
Temperature : -4˚F ~ 113˚F (-20˚C ~ 45˚C)
Humidity : 5 % – 95 %, non-condensing
The above specifications are subject to change without notice to improve quality.
This device is a Class B digital apparatus.
[Recommendation] - EU Only
z
Hereby, Samsung Electronics, declares that this [Thin Client] is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC.
z
The official Declaration of Conformity may be found at http://www.samsunglfd.com, go to
Support > Search Product Support and enter the model name.
z
This equipment may only be used indoors.
z
This equipment may be operated in all EU countries.
5 Specifications
45
5
Specifications
(USA only)
Dispose unwanted electronics through an approved recycler.
To find the nearest recycling location, go to our website:
www.samsung.com/recyclingdirect or call, (877) 278 - 0799
CALIFORNIA USA ONLY (Applicable for networking models only.)
This Perchlorate warning applies only to primary CR(Manganese Dioxide) Lithium coin cells in the
product sold or distributed ONLY in California USA
"Perchloate Material - special handling may apply, See www.dtsc.ca.gov/hazardouswaste/
perchlorate."
5.2
Power consumption
Normal operation mode
PowerSaver
Typical
Power lamp
Power
Consumption
Power off
(Power
switch off)
Off
Off
Off
Rating
On
12 W
Stand by (S3)
Power off
(S5)
(Power
button off)
36 W
Less than 2.0 W Less than 2.0 W
0W
z
The power consumption level can vary in different operating conditions or when settings are
changed.
z
To reduce the power consumption to 0 watts, turn off the switch on the adapter or disconnect the
power cable. Be sure to disconnect the power cable when you will not be using the product for an
extended period of time. To reduce the power consumption to 0 watts when the power switch is
not available, disconnect the power cable.
5 Specifications
46
Appendix
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG
customer care center.
NORTH AMERICA
U.S.A
1-800-SAMSUNG (726-7864)
http://www.samsung.com
CANADA
1-800-SAMSUNG (726-7864)
http://www.samsung.com/ca
(English)
http://www.samsung.com/ca_fr
(French)
MEXICO
01-800-SAMSUNG (726-7864)
http://www.samsung.com
LATIN AMERICA
ARGENTINE
0800-333-3733
http://www.samsung.com
BOLIVIA
800-10-7260
http://www.samsung.com
BRAZIL
0800-124-421
4004-0000
http://www.samsung.com
CHILE
800-SAMSUNG (726-7864)
http://www.samsung.com
From mobile 02-482 82 00
COLOMBIA
01-8000112112
http://www.samsung.com
COSTA RICA
0-800-507-7267
http://www.samsung.com/latin
(Spanish)
http://www.samsung.com/latin_en
(English)
DOMINICA
1-800-751-2676
http://www.samsung.com/latin
(Spanish)
http://www.samsung.com/latin_en
(English)
ECUADOR
1-800-10-7267
http://www.samsung.com/latin
(Spanish)
http://www.samsung.com/latin_en
(English)
EL SALVADOR
800-6225
http://www.samsung.com/latin
(Spanish)
http://www.samsung.com/latin_en
(English)
Appendix
47
Appendix
LATIN AMERICA
GUATEMALA
1-800-299-0013
http://www.samsung.com/latin
(Spanish)
http://www.samsung.com/latin_en
(English)
HONDURAS
800-27919267
http://www.samsung.com/latin
(Spanish)
http://www.samsung.com/latin_en
(English)
JAMAICA
1-800-234-7267
http://www.samsung.com
NICARAGUA
00-1800-5077267
http://www.samsung.com/latin
(Spanish)
http://www.samsung.com/latin_en
(English)
PANAMA
800-7267
http://www.samsung.com/latin
(Spanish)
http://www.samsung.com/latin_en
(English)
PERU
0-800-777-08
http://www.samsung.com
PUERTO RICO
1-800-682-3180
http://www.samsung.com
TRINIDAD & TOBAGO
1-800-SAMSUNG (726-7864)
http://www.samsung.com
VENEZUELA
0-800-100-5303
http://www.samsung.com
EUROPE
AUSTRIA
0810 - SAMSUNG
(7267864, € 0.07/min)
http://www.samsung.com
BELGIUM
02-201-24-18
http://www.samsung.com/be
(Dutch)
http://www.samsung.com/be_fr
(French)
BOSNIA
05 133 1999
http://www.samsung.com
BULGARIA
07001 33 11 , normal tariff
http://www.samsung.com
CROATIA
062 SAMSUNG (062 726 7864)
http://www.samsung.com
CYPRUS
8009 4000 only from landline
http://www.samsung.com
(+30) 210 6897691 from mobile
and land line
Appendix
48
Appendix
EUROPE
CZECH
800 - SAMSUNG (800-726786)
http://www.samsung.com
Samsung Electronics Czech and Slovak, s.r.o.,
Oasis Florenc, Sokolovská 394/17, 180 00, Praha 8
DENMARK
70 70 19 70
http://www.samsung.com
EIRE
0818 717100
http://www.samsung.com
ESTONIA
800-7267
http://www.samsung.com
FINLAND
09 85635050
http://www.samsung.com
FRANCE
01 48 63 00 00
http://www.samsung.com
GERMANY
0180 5 SAMSUNG bzw.
http://www.samsung.com
0180 5 7267864* (*0,14 €/Min. aus
dem dt. Festnetz, aus dem
Mobilfunk max. 0,42 €/Min.)
GREECE
80111-SAMSUNG (80111 726
7864) only from land line
http://www.samsung.com
(+30) 210 6897691 from mobile
and land line
HUNGARY
06-80-SAMSUNG (726-7864)
http://www.samsung.com
ITALIA
800-SAMSUNG (726-7864)
http://www.samsung.com
LATVIA
8000-7267
http://www.samsung.com
LITHUANIA
8-800-77777
http://www.samsung.com
LUXEMBURG
261 03 710
http://www.samsung.com
MACEDONIA
023 207 777
http://www.samsung.com
MONTENEGRO
020 405 888
http://www.samsung.com
NETHERLANDS
0900 - SAMSUNG
(0900-7267864) (€ 0,10/Min)
http://www.samsung.com
NORWAY
815 56480
http://www.samsung.com
POLAND
0 801-1SAMSUNG (172-678)
+48 22 607-93-33
http://www.samsung.com
PORTUGAL
808 20 - SAMSUNG (808 20 7267)
http://www.samsung.com
RUMANIA
08008 SAMSUNG (08008 726
7864)
http://www.samsung.com
TOLL FREE No.
SERBIA
0700 Samsung (0700 726 7864)
http://www.samsung.com
SLOVAKIA
0800 - SAMSUNG (0800-726 786)
http://www.samsung.com
SPAIN
902 - 1 - SAMSUNG (902 172 678)
http://www.samsung.com
Appendix
49
Appendix
EUROPE
SWEDEN
0771 726 7864 (SAMSUNG)
http://www.samsung.com
SWITZERLAND
0848-SAMSUNG
(7267864, CHF 0.08/min)
http://www.samsung.com/ch
(German)
http://www.samsung.com/ch_fr
(French)
U.K
0330 SAMSUNG (7267864)
http://www.samsung.com
CIS
ARMENIA
0-800-05-555
http://www.samsung.com
AZERBAIJAN
088-55-55-555
http://www.samsung.com
BELARUS
810-800-500-55-500
http://www.samsung.com
GEORGIA
0-800-555-555
http://www.samsung.com
KAZAKHSTAN
8-10-800-500-55-500
(GSM: 7799)
http://www.samsung.com
KYRGYZSTAN
00-800-500-55-500
http://www.samsung.com
MOLDOVA
0-800-614-40
http://www.samsung.com
MONGOLIA
+7-800-555-55-55
http://www.samsung.com
RUSSIA
8-800-555-55-55
http://www.samsung.com
TADJIKISTAN
8-10-800-500-55-500
http://www.samsung.com
UKRAINE
0-800-502-000
http://www.samsung.com/ua
(Ukrainian)
http://www.samsung.com/ua_ru
(Russian)
UZBEKISTAN
8-10-800-500-55-500
http://www.samsung.com
ASIA PACIFIC
AUSTRALIA
1300 362 603
http://www.samsung.com
CHINA
400-810-5858
http://www.samsung.com
HONG KONG
(852) 3698 - 4698
http://www.samsung.com/hk
(Chinese)
http://www.samsung.com/hk_en
(English)
Appendix
50
Appendix
ASIA PACIFIC
INDIA
http://www.samsung.com
1800 1100 11
3030 8282
1800 3000 8282
1800 266 8282
INDONESIA
0800-112-8888
021-5699-7777
http://www.samsung.com
JAPAN
0120-327-527
http://www.samsung.com
MALAYSIA
1800-88-9999
http://www.samsung.com
NEW ZEALAND
0800 SAMSUNG (0800 726 786)
http://www.samsung.com
PHILIPPINES
1-800-10-SAMSUNG (726-7864)
for PLDT
http://www.samsung.com
1-800-3-SAMSUNG (726-7864)
for Digitel
1-800-8-SAMSUNG (726-7864)
for Globe
02-5805777
SINGAPORE
1800-SAMSUNG (726-7864)
http://www.samsung.com
TAIWAN
0800-329-999
http://www.samsung.com
0266-026-066
THAILAND
1800-29-3232
http://www.samsung.com
02-689-3232
VIETNAM
1 800 588 889
http://www.samsung.com
MIDDlE EAST
BAHRAIN
8000-4726
http://www.samsung.com/ae
(English)
http://www.samsung.com/ae_ar
(Arabic)
EGYPT
08000-726786
http://www.samsung.com
IRAN
021-8255
http://www.samsung.com
JORDAN
800-22273
http://www.samsung.com
065777444
KUWAIT
183-2255
http://www.samsung.com/ae
(English)
http://www.samsung.com/ae_ar
(Arabic)
Appendix
51
Appendix
MIDDlE EAST
MOROCCO
080 100 2255
http://www.samsung.com
OMAN
800-SAMSUNG (726-7864)
http://www.samsung.com/ae
(English)
http://www.samsung.com/ae_ar
(Arabic)
SAUDI ARABIA
9200-21230
http://www.samsung.com/ae
(English)
http://www.samsung.com/ae_ar
(Arabic)
TURKEY
444 77 11
http://www.samsung.com
U.A.E
800-SAMSUNG (726-7864)
http://www.samsung.com
AFRICA
ANGOLA
91-726-7864
http://www.samsung.com
BOTSWANA
0800-726-000
http://www.samsung.com
CAMEROON
7095- 0077
http://www.samsung.com
COTE D’ IVOIRE
8000 0077
http://www.samsung.com
GHANA
0800-10077
http://www.samsung.com
0302-200077
KENYA
0800 724 000
http://www.samsung.com
NAMIBIA
8197267864
http://www.samsung.com
NIGERIA
0800-726-7864
http://www.samsung.com
SENEGAL
800-00-0077
http://www.samsung.com
SOUTH AFRICA
0860-SAMSUNG (726-7864)
http://www.samsung.com
TANZANIA
0685 88 99 00
http://www.samsung.com
UGANDA
0800 300 300
http://www.samsung.com
ZAMBIA
211350370
http://www.samsung.com
Appendix
52
Appendix
Responsibility for the Pay Service (Cost to Customers)
When the service is requested, in spite of in warranty, we may charge you for a visit from a service
technician in the following cases.
Not a product defect
Cleaning of the product, Adjustment, Explanation, Re-installation and etc.
z
If a service technician gives instructions on how to use product or simply adjusts options without
disassembling product.
z
If a defect is caused by external environmental factors (Internet, Antenna, Wired Signal, etc.).
z
If a product is reinstalled or devices are connected additionally after installing the purchased product
for the first time.
z
If a product is reinstalled to move to a different spot or to move to a different house.
z
If customer requests instructions on how to use because of another company's product.
z
If customer requests instructions on how to use the network or another company's program.
z
If customer requests software installation and setup for the product.
z
If a service technician removes/cleans dusts or foreign materials inside of the product.
z
If customer requests an installation additionally after purchasing a product through home-shopping
or online.
A Product damage caused by customer's fault
Product damage caused by customer's mishandling or wrong repair.
If a product damage is caused by;
z
external impact or drop.
z
use of supplies or separatly sold product unspecified by Samsung.
z
repair from a person besides an engineer of outsourcing service company or partner of Samsung
Electronics Co., Ltd.
z
remodeling or repairing the product by customer.
z
using it with incorrect voltage or non-authorised electrical connections.
z
not following the "cautions" in User Manual.
Others
z
If product fails by natural disaster (lightning, fire, earthquake, flood damage, etc).
z
If consumable components are all used up (Battery, Toner, Fluorescent lights, Head, Vibrator, Lamp,
Filter, Ribbon, etc.).
If customer requests a service in case the product has no defect, service fee may be charged.
So please read User Manual first.
Appendix
53
Appendix
Correct Disposal
Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
(Applicable in countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its
electronic accessories (e.g. charger, headset, USB cable) should not be disposed of
with other household waste at the end of their working life. To prevent possible harm to
the environment or human health from uncontrolled waste disposal, please separate
these items from other types of waste and recycle them responsibly to promote the
sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product,
or their local government office, for details of where and how they can take these items
for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the
purchase contract. This product and its electronic accessories should not be mixed with
other commercial wastes for disposal.
Correct disposal of batteries in this product
(Applicable in countries with separate collection systems)
The marking on the battery, manual or packaging indicates that the battery in this
product should not be disposed of with other household waste. Where marked, the
chemical symbols Hg, Cd or Pb indicate that the battery contains mercury, cadmium or
lead above the reference levels in EC Directive 2006/66.
The battery incorporated in this product is not user replaceable. For information on its
replacement, please contact your service provider. Do not attempt to remove the
battery or dispose it in a fire. Do not disassemble, crush, or puncture the battery.
If you intend to discard the product, the waste collection site will take the appropriate
measures for the recycling and treatment of the product, including the battery.
Appendix
54
Index
C
Checking the Contents 15
Connection to Use Windows Embedded
Standard 7 24
Contact SAMSUNG WORLD WIDE 47
Copyright 5
Correct Disposal 54
G
General 45
I
Installation 21
P
Parts 18
Power consumption 46
R
Requirements Before Contacting Samsung
Customer Service Center 44
Responsibility for the Pay Service (Cost to
Customers) 53
S
Safety Precautions 8
U
Using "Windows Embedded Standard 7" 28
W
What is "Windows Embedded Standard 7"
Client? 23
Index
55
Download PDF

advertising