Samsung | PS-42E7S | Samsung PS-42E7S Benutzerhandbuch

BN68-00955P-03Eng_0213
2/13/06
10:39 AM
Page 1
PDP-TELEVISION
(PLASMA DISPLAY PANEL)
Owner’s Instructions
Before operating the unit,
please read this manual thoroughly,
and retain it for future reference.
ON-SCREEN MENUS
Picture In Picture (PIP)
Energy Saving
TELETEXT (Option)
SRS TruSurroundXT
Digital Natural Image engine
This device is a Class B digital apparatus.
Register your product at www.samsung.com/global/register
nt
d
BN68-00955P-03Eng_0213
2/13/06
10:39 AM
Page 2
User Instructions
◆ Screen Image retention
Do not display a still image (such as on a video game or when hooking up a PC to this PDP) on the plasma
monitor panel for more than 2 hours as it can cause screen image retention. This image retention is also known
as “screen burn”. To avoid such image retention, reduce the degree of brightness and contrast of the screen when
displaying a still image.
◆ Height
The PDP can normally operate only under 2000m in height. It might abnormally function at a place over 2000m in
height so do not install and operate there.
◆ Heat on the top of the PDP TV
The top side of the product may be hot after long periods of use as heat dissipates from the panel through the vent
hole in the upper part of the product. This is normal and does not indicate any defect or operation failure of the
product. However, children should be prevented from touching the upper part of the product.
◆ The product is making a ‘cracking’ noise.
A ‘cracking’ noise may occur when the product contracts or expands due to a change of surrounding environment
such as temperature or humidity. This is normal and not a defect of the unit.
◆ Cell Defects
The PDP uses a panel consisting of 1,230,000(SD-level) to 3,150,000(HD-level) pixels which require sophisticated
technology to produce. However, there may be few bright or dark pixels on the screen.
These pixels will have no impact on the performance of the product.
◆ Avoid operating the TV at temperatures below 5°C(41°F)
◆ A still image displayed too long may cause permanent damage to the PDP Panel.
Watching the PDP TV in 4:3 format for a long period of time may leave traces of borders
displayed on the left, right and centre of the screen caused by the difference of light
emission on the screen.
Playing a DVD or a game console may cause similar effect to the screen.
Damages caused by the above effect are not covered by the Warranty.
◆ Afterimage on the Screen.
Displaying still images from Video games and PC for longer than a certain period of time may produce partial
afterimages. To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when displaying still images.
◆ Warranty
- Warranty does not cover any damage caused by image retention.
- Burn-in is not covered by the warranty.
◆ Installation
Be sure to contact an authorized service centre, when installing your set in a location with heavy dust, high or low
temperatures, high humidity, chemical substance and where it operates continually such as the airport, the train
station etc. Failure to do so may cause a serious damage to your set.
Checking Parts
Sold Separately
Warranty Card/
Registration Card/
Owner’s Remote Control/
Safety Guide Manual
Instructions AAA Batteries (Not available in all
locations)
Power Cord
➢
S-VIDEO Cable HDMI Cable Antenna Cable Component Cables
(RCA)
Coaxial Connector Ferrite Core for
(Philippine Option) S-VIDEO Cable
(Side AV)
PC Cable
Ferrite Core for S-VIDEO Cable (Side AV)
The ferrite core is used to shield the cable
from interference.
When connecting a cable, open the ferrite
core and clip it around the cable near the plug.
English - 2
PC Audio Cable
HDMI/DVI Cable
n
nt
d
BN68-00955P-03Eng_0213
2/13/06
10:39 AM
Page 3
Contents
◆ GENERAL INFORMATION
■
■
■
■
■
■
■
User Instructions ...................................................................................................
Checking Parts......................................................................................................
Control Panel ........................................................................................................
Connection Panel..................................................................................................
Using the Stand-Base ...........................................................................................
Viewing the Remote Control (depending on the model) .......................................
Installing Batteries in the Remote Control ............................................................
2
2
4
4
6
6
7
◆ OPERATION
■
■
■
■
■
■
Switching Your Television On and Off ...................................................................
Viewing the Menus................................................................................................
Freezing the Current Picture.................................................................................
Plug & Play Feature ..............................................................................................
Viewing an External Signal Source.......................................................................
Editing Device Names...........................................................................................
7
8
8
9
10
10
◆ CHANNEL CONTROL
■
■
■
■
■
■
Storing Channels Automatically ............................................................................
Storing Channels Manually ...................................................................................
Adding / Locking Channels ...................................................................................
Sorting the Stored Channels.................................................................................
Assigning Names to Channels..............................................................................
Fine Tuning Channel Reception............................................................................
11
12
13
14
14
15
◆ PICTURE CONTROL
■
■
■
■
■
■
Changing the Picture Standard.............................................................................
Customizing the Picture Settings ..........................................................................
Selecting the Picture Size .....................................................................................
Digital NR ..............................................................................................................
DNIe Demo ...........................................................................................................
Viewing the Picture in Picture (PIP) ......................................................................
16
16
17
17
17
18
◆ SOUND CONTROL
■
Sound Features.....................................................................................................
19
◆ FUNCTION DESCRIPTION
■
■
■
■
■
■
■
Time Features .......................................................................................................
Language ..............................................................................................................
Blue Screen...........................................................................................................
Melody...................................................................................................................
Energy Saving.......................................................................................................
Using Game Mode ................................................................................................
Screen Burn Protection .........................................................................................
20
21
21
21
21
21
22
◆ PC DISPLAY
■
■
■
■
Setting up Your PC Software (Based on Windows XP) ........................................
Input Mode (PC)....................................................................................................
Setting the PC .......................................................................................................
Teletext Feature (depending on the model) ..........................................................
23
23
24
25
◆ APPENDIX
■
■
How to Install the Wall Mount Bracket ..................................................................
Troubleshooting.....................................................................................................
☛
Symbols
Press
Important
English - 3
➢
Note
27
29
BN68-00955P-03Eng_0213
2/13/06
10:39 AM
Page 4
Control Panel
➢
The product colour and shape may vary depending on the model.
Front (or Side) Panel
Speaker
ΠSOURCE
Displays a menu of all of the available input sources
(TV, AV1, AV2, S-Video, Component1, Component2,
PC, HDMI).
¨ CH
,
Press to change channels. In the on-screen menu,
use the CH
,
buttons as you use the … and †
buttons on the remote control.
´ MENU
Press to see the on-screen menu of your TV’s
features.
ˆ
(ENTER)
Press to confirm a selection.
Ø
(Power) button
Press to turn the TV on and off.
ˇ VOL +, Press to increase or decrease the volume.
In the on-screen menu, use the VOL +, - buttons as
you use the œ and √ buttons on the remote control.
Power Indicator
- Power Off: Red
- Power On: Off
Remote Control Sensor
Aim the remote control towards this spot on the TV.
Connection Panel
➢
The product colour and shape may vary depending on the model.
Side Panel
Œ
or
´
ΠS-Video or Video / Audio L/R
- Video (S-Video or Video) and
audio inputs for external devices,
such as a camcorder or VCR.
´ headphones jack
- You can connect a set of
headphones to your television if
you wish to watch a television
programme without disturbing the
other people in the room.
➢
continued...
English - 4
Prolonged use of headphones
at a high volume may damage
your hearing.
†
BN68-00955P-03Eng_0213
2/13/06
10:40 AM
Page 5
Connection Panel
➢
The product colour and shape may vary depending on the model.
Rear Panel
∏
Œ
”
or
Cable Television
Network
or
Ø
ˆ
´
¨
ˇ
☛ Whenever you connect an audio or video system to your set, ensure that all elements are switched off.
☛ When connecting an external device, match the colour of the connection terminal to the cable.
- When connecting this product via HDMI or DVI to a
Œ ANT IN VHF/UHF (75Ω)
Set Top Box, DVD Player or Games Console etc,
- 75Ω Coaxial connector for Aerial/Cable Network.
make sure that it has been set to a compatible video
´ Connecting external Audio Devices
output mode as shown in the table below. Failure to
- Connect RCA audio signals from the TV to an external
observe this may result in picture distortion, image
source, such as Audio equipment.
breakup or no picture.
ˇ PC IN / AUDIO
- Do not attempt to connect the HDMI/DVI connector to a
- Connect to the video and audio output jack on your PC.
PC or Laptop Graphics Card.
(This will result in a blank screen being displayed)
¨ Connecting External A/V Devices
- Connect RCA cable to an appropriate external A/V
DVI AUDIO IN L/R
device such as VCR, DVD or Camcorder.
- DVI audio outputs for external devices.
- Connect RCA audio cables to “R - AUDIO - L” on the
∏ POWER IN
rear of your set and the other ends to corresponding
- Connect the supplied power cord.
audio out connectors on the A/V device.
” SERVICE
ˆ COMPONENT IN 1, COMPONENT IN 2
- Connector for service only.
- Video (Y/PB/PR) and audio (AUDIO L/R) inputs for
Component.
Supported modes for HDMI/DVI and Component
➢
Ø HDMI/DVI IN
576p
720p 1080i
576i
480p
480i
- Connect to the HDMI jack of a device with HDMI output.
HDMI/DVI 50Hz
O
O
O
X
O
These inputs can also be used as a DVI connection
X
with separate analog audio inputs. An optional
HDMI/DVI 60Hz
O
O
X
X
O
X
HDMI/DVI cable will be necessary to make this
Component
O
O
O
O
O
O
connection. When using the optional HDMI/DVI adapter,
the DVI analog audio inputs on your TV allow you to
receive left and right audio from your DVI device.
(Not compatible with PC)
English - 5
BN68-00955P-03Eng_0213
2/13/06
10:40 AM
Page 6
Using the Stand-Base
➢
➢
Two or more people should carry the PDP. Never lay the PDP on
the floor because of possible damage to the screen.
Always keep the PDP upright.
Pull the folded stand in the direction of the arrow.
Stand
Viewing the Remote Control (depending on the model)
ΠPOWER button
(turns the TV on and off)
´ Number buttons for direct
channel access
ˇ One/Two-digit channel
selection
¨ Channel control button
(Refer to page 13)
ˆ Selects the TV mode directly
Ø
Volume increase
Volume decrease
¸ Exit the on-screen menu
˛ Control the cursor in the menu
◊ Use to see information on the
current broadcast
≠ Picture freeze
– Picture size selection
— Select the channel of sub
picture (PIP)
Teletext Functions
(Refer to page 25)
∏ Temporary sound switch-off
ˆ Exit from the teletext display
(depending on the model)
” Displays the main on-screen
menu
” Teletext index
’ Picture-In-Picture On/Off
˝ Sound effect selection
(Refer to page 19)
Ô Picture effect selection
(Refer to page 16)
 Adjust screen brightness to
surrounding environment
(Refer to page 21)
Ú Sound mode selection
Æ TruSurround XT mode button
ı Available source selection
˜ Previous channel
¯ Automatic Power-off
˘ Selects the PC mode directly
¿
➢
➢
’ Teletext hold
Ò Teletext store
ı Teletext mode selection
(LIST/FLOF)
˜ Teletext sub page
¿ P
P
: Teletext next page
: Teletext previous page
¸ Teletext cancel
◊ Teletext reveal
± Teletext display/mix both
teletext information and
the normal broadcast
÷ Teletext size selection
˝Ô≠–
Fastext topic selection
Next channel
Previous channel
The performance of the remote control may be affected by bright light.
This is a special remote control for the visually impaired, and has Braille points on the Power, Channel and
Volume buttons.
English - 6
BN68-00955P-03Eng_0213
2/13/06
10:40 AM
Page 7
Installing Batteries in the Remote Control
1
Lift the cover at the back of the remote control upward as shown in the figure.
2
Install two AAA size batteries.
➢ Make sure to match the “+” and “–” ends of the batteries with the diagram
inside the compartment.
3
➢
Close the cover as shown in the figure.
Remove the batteries and store them in a cool, dry place if you won’t be using
the remote control for a long time. The remote control can be used up to
about 23 feet from the TV. (Assuming typical TV usage, the batteries last for
about one year.)
➢
If the remote control doesn’t work! Check the following:
1. Is the TV power on?
2. Are the plus and minus ends of the batteries reversed?
3. Are the batteries drained?
4. Is there a power cut, or is the power cord unplugged?
5. Is there a special fluorescent light or a neon sign nearby?
Switching Your Television On and Off
The mains lead is attached to the rear of the television.
1
Plug the mains lead into an appropriate socket.
➢
2
The main voltage is indicated on the rear of the television and the frequency is 50 or 60Hz.
Press the
(Power) button (On/Off) on the front of the television or press the POWER ( ) button on the remote
control to switch the television on. The programme that you were watching last is re-selected automatically.
If you have not yet stored any channels, no clear picture appears. Refer to “Storing Channels Automatically”
on page 11 or “Storing Channels Manually” on page 12.
➢
If the television is initially powered on, several basic customer settings proceed automatically.
Refer to “Plug & Play Feature” on page 9.
3
To switch the television off, press the
(Power) button (On/Off) on the front of the television or press the
POWER ( ) button on the remote control.
4
To switch the TV on, press the
(Power) button (On/Off) on the front of the TV or press the POWER ( ) button
or number buttons on the remote control.
English - 7
BN68-00955P-03Eng_0213
2/13/06
10:40 AM
Page 8
Viewing the Menus
TV
Input
Source List
Edit Name
Move
1
Press the MENU (
) button.
The main menu is displayed on the screen.
Its left side has five icons: Input, Picture, Sound, Channel, and Setup.
2
Press the … or † button to select one of the icons.
) button to access the icon’s sub-menu.
Press the ENTER (
3
Press the … or † button to move to items in the menu.
) button to enter items in the menu.
Press the ENTER (
4
Press the …/†/œ/√ button to change the selected items.
Press the MENU (
) button to return to the previous menu.
5
Press the EXIT button to exit from the menu.
: TV
Enter
Exit
Freezing the Current Picture
You can freeze the picture when watching a television programme simply by
pressing the “STILL” button. To return to normal viewing, press it again.
➢
This function will automatically cancel five minutes later.
English - 8
.
BN68-00955P-03Eng_0213
2/13/06
10:40 AM
Page 9
Plug & Play Feature
When the television is initially powered on, several basic customer settings proceed automatically and subsequently.
The following settings are available.
1
2
3
Plug & Play
If the television is in standby mode, press the POWER ( ) button
on the remote control. The message to start Plug & Play is displayed.
Start Plug & Play.
The Language menu will automatically appear after several seconds.
OK
Enter
Select the appropriate language by pressing the … or † button.
) button. The message to check the connected status
Press the ENTER (
of the antenna is displayed.
4
Make sure that the antenna is connected to the TV.
) button. The Area menu is displayed.
Press the ENTER (
5
Select your country or area by pressing the … or † button.
) button. The menu to select channels is displayed.
Press the ENTER (
6
) button.
To start channel store, press the ENTER (
The search will end automatically. The TV will begin memorizing all of the
available channels.
) button to set the clock.
Press the ENTER (
Exit
Plug & Play
Language
English
Français
Move
Enter
Skip
Plug & Play
Check antenna input.
7
Skip
Plug & Play
Area
Press the œ or √ button to select the hour, minute, or am/pm.
Set these by pressing the … or † button.
➢
8
OK
Enter
You can enter the hours or minutes by using the numeric buttons on the
remote control.
Asia/W.Europe
CIS/E.Europe
China
Move
Enter
Skip
Plug & Play
) button to confirm your setting.
Press the ENTER (
The message “Enjoy your viewing” is displayed.
Auto Store
P 1
--
C
40 MHz
0%
Start
Enter
Skip
Plug & Play
-- : -- am
Clock Set
Enter
Skip
Plug & Play
Clock Set
Move
12 : 00 am
Adjust
Enter
Skip
Enjoy your viewing
OK
If you want to reset this feature …
1
2
3
Press the MENU (
) button to display the menu.
Press the … or † button to select Setup, then press the ENTER (
button.
Press the ENTER (
) button again to select Plug & Play.
The message to start Plug & Play is displayed.
TV
)
Setup
Plug & Play
Language
Time
Game Mode
Blue Screen
Melody
PC
More
Move
English - 9
: English
: Off
: Off
: Off
Enter
Return
BN68-00955P-03Eng_0213
2/13/06
10:40 AM
Page 10
Viewing an External Signal Source
TV
You can switch between viewing signal from connected equipment, such as a
VCR, DVD, Set-Top Box, and the TV source (broadcast or cable).
Input
Source List
Edit Name
: TV
Move
TV
Enter
Return
Source List
TV
AV1
AV2
S-Video
Component1
Component2
PC
HDMI
Move
:
:
:
:
:
:
:
1
Press the MENU (
) button to display the menu.
2
Press the ENTER (
) button to select Source List.
3
Press the ENTER (
) button again.
4
Press the … or † button to select the signal source, then press the
ENTER (
) button.
----------------------
Enter
Available signal source: TV, AV1, AV2, S-Video, Component1,
Component2, PC, HDMI
Return
➢
➢
You can select these options simply by pressing the SOURCE button
on the remote control.
You can enter TV or PC mode directly by using the TV or PC button on the
remote control unit.
Editing Device Names
TV
You can give a name to the external source.
Input
Source List
Edit Name
Move
TV
: TV
1
Enter
Press the MENU (
) button to display the menu.
2
Press the ENTER (
) button.
3
Press the … or † button to select Edit Name, then press the
ENTER (
) button.
4
Press the … or † button to select the external source to be edited, then
) button.
press the ENTER (
5
Select the required device by pressing … or †, then press the ENTER (
button.
Return
Edit Name
AV1
AV2
S-Video
Component1
Component2
PC
HDMI
Move
:
:
:
:
:
:
:
---- ------- VCR
---DVD
-------D-VHS
Cable STB
-------
Enter
Available device names: VCR, DVD, D-VHS, Cable STB, HD STB,
Satellite STB, AV Receiver, DVD Receiver, Game, Camcorder,
DVD Combo, DHR (DVD HDD Recorder), or PC.
Return
6
Press the EXIT button to exit.
English - 10
)
BN68-00955P-03Eng_0213
2/13/06
10:40 AM
Page 11
Storing Channels Automatically
You can scan for the frequency ranges available to you (availability depends on your area).
Automatically allocated programme numbers may not correspond to actual or desired programme numbers.
However you can sort numbers manually and clear any channels you do not wish to watch.
1
Press the MENU (
2
Press the … or † button to select Channel, then press the ENTER (
3
Press the ENTER (
4
Select your area by pressing the … or † button, then press the ENTER (
button.
)
5
Press the … or † button to select Auto Store, then press the ENTER (
button.
)
6
Press the ENTER (
) button again to start the search.
The search will end automatically.
➢
) button to display the menu.
TV
) button.
) button again. The available areas are listed.
To stop the search before it has finished, press the MENU (
ENTER (
) button.
e
)
English - 11
Channel
Area
: Asia/W.Europe
Auto Store
Manual Store
Channel Manager
Sort
Name
Fine Tune
Move
Enter
Return
Auto Store
P 1
C
--
40 MHz
0%
) or the
Start
Enter
Return
BN68-00955P-03Eng_0213
2/13/06
10:40 AM
Page 12
Storing Channels Manually
You can store television channels, including those received via cable networks.
When storing channels manually, you can choose:
◆ Whether or not to store each of the channels found.
◆ The programme number of each stored channel which you wish to identify.
TV
Channel
Area
: Asia/W.Europe
Auto Store
Manual Store
Channel Manager
Sort
Name
Fine Tune
Move
TV
Enter
1
Press the MENU (
2
Press the … or † button to select Channel, then press the ENTER (
button.
3
Press the … or † button to select Manual Store, then press the
ENTER (
) button.
4
Select the required option by pressing the … or † button, then press the
ENTER (
) button.
5
When you are satisfied with your setting, press the ENTER (
6
Press the EXIT button to exit.
Move
:P
1
: AUTO
: BG
: C
2
: 48 MHz
:?
Enter
)
Return
Manual Store
Programme
Colour System
Sound System
Channel
Search
Store
) button to display the menu.
) button.
Return
◆ Programme (Programme number to be assigned to a channel)
- Press the … or † button until you find the correct number.
◆ Colour System: AUTO/PAL/SECAM/NTSC4.43/NTSC3.58
- Press the … or † button to select the required colour standard.
◆ Sound System: BG/DK/I/M
- Press the … or † button to select the required sound standard.
◆ Channel (When you know the number of the channel to be stored)
- Press the … or † button to select C (Air channel) or S (Cable channel).
- Press the √ button, then press the … or † button to select the required number.
➢
➢
You can also select the channel number directly by pressing the numeric buttons (0~9).
If there is abnormal sound or no sound, re-select the sound standard required.
◆ Search (When you do not know the channel numbers)
- Press the … or † button to start the search.
- The tuner scans the frequency range until the first channel or the channel that you selected is received
on the screen.
◆ Store (When you store the channel and associated programme number)
- Set to OK by pressing the ENTER (
) button.
☛
Channel mode
◆ P (Programme mode): When completing tuning, the broadcasting stations in your area have been assigned
to position numbers from P00 to P99. You can select a channel by entering the position number in this mode.
◆ C (Air channel mode): You can select a channel by entering the assigned number to each air broadcasting
station in this mode.
◆ S (Cable channel mode): You can select a channel by entering the assigned number for each cable channel
in this mode.
English - 12
BN68-00955P-03Eng_0213
2/13/06
10:40 AM
Page 13
Adding / Locking Channels
Using the Channel Manager, you can conveniently lock or add channels.
1
Press the MENU (
TV
) button to display the menu.
2
Press the … or † button to select Channel, then press the ENTER (
3
Press the … or † button to select Channel Manager, then press the
ENTER (
) button.
) button.
Move
◆ Adding channels
Using the Channel Manager, you can add channels.
TV
Select the Channel Manager by pressing the ENTER (
Move to the (
) field by pressing the …/†/œ/√ buttons, select a channel to
) button to add the channel.
be added, and press the ENTER (
) symbol next to the
If you press the ENTER (
) button again, the (
channel disappears and the channel is not added.
◆ Locking channels
This feature allows you to prevent unauthorized users, such as children, from
watching unsuitable programmes by muting out video and audio.
6
Press the … or † button to select Child Lock, then press the ENTER (
button.
7
Select On by pressing the … or † buttons, then press the ENTER (
button.
8
Press the … or † buttons to select the Channel Manager, then press the
ENTER (
) button.
9
Move to the ( ) field by pressing the …/†/œ/√ buttons, select a channel to
) button.
be locked, and press the ENTER (
➢
)
If you press the ENTER (
) button again, the ( ) symbol next to the
channel disappears and the channel lock is canceled.
A blue screen is displayed when Child Lock is activated.
10 Press the EXIT button to exit.
➢
You can select these options simply by pressing the CH MGR button
on the remote control.
English - 13
Return
) button.
4
➢
Enter
Channel Manager
Channel Manager
Child Lock
: Off
5
➢
Channel
Area
: Asia/W.Europe
Auto Store
Manual Store
Channel Manager
Sort
Name
Fine Tune
)
Move
Enter
Channel Manager
P 1 C 16 BBC 1
1 / 10
Prog.
0 C -1 BBC 1
2 C3
3 S1
4 S3
5 S6
6 S7
7 S9
8 S 11
9 S 12
Add
Lock
Move
Enter
Page
Return
Return
BN68-00955P-03Eng_0213
2/13/06
10:40 AM
Page 14
Sorting the Stored Channels
TV
Channel
Area
: Asia/W.Europe
Auto Store
Manual Store
Channel Manager
Sort
Name
Fine Tune
Move
TV
Enter
Return
Sort
This operation allows you to change the programme numbers of stored channels.
This operation may be necessary after using auto store.
1
Press the MENU (
2
Press the … or † button to select Channel, then press the ENTER (
3
Press the … or † button to select Sort, then press the ENTER (
4
Select the channel that you wish to move by pressing the … or † button,
) button.
then press the ENTER (
5
Select the number of the programme to which the channel is to be moved
by pressing the … or † button.
) button. The channel is moved to its new position and
Press the ENTER (
all other channels are shifted accordingly.
6
Repeat steps 4 to 5 until you have moved all the channels to the required
programme numbers.
7
Press the EXIT button to exit.
Prog. Channel Name
0
1
2
3
4
C -C2
C 83
C 80
C7
Move
Enter
Return
) button to display the menu.
) button.
) button.
Assigning Names to Channels
TV
Channel
Area
: Asia/W.Europe
Auto Store
Manual Store
Channel Manager
Sort
Name
Fine Tune
Move
TV
Enter
Return
Name
Programme Channel
0
1
2
3
4
C -C2
C 83
C 80
C7
Move
Channel names will be assigned automatically when channel information is
broadcast. These names can be changed, allowing you to assign new names.
1
Press the MENU (
2
Press the … or † button to select Channel, then press the ENTER (
) button.
3
Press the … or † button to select Name, then press the ENTER (
) button.
4
Press the … or † button to select the channel to be assigned to a new name,
then press the ENTER (
) button.
5
Press the … or † button to select a letter (A~Z), a number (0~9), or a symbol.
Move on to the previous or next letter by pressing the œ or √ button, then
press the ENTER (
) button.
6
Repeat steps 4 to 5 for each channel to be assigned to a new name.
7
Press the EXIT button to exit.
Name
--------A
-------------
Adjust
Return
English - 14
) button to display the menu.
BN68-00955P-03Eng_0213
2/13/06
10:40 AM
Page 15
Fine Tuning Channel Reception
If the reception is clear, you do not have to fine tune the channel, as this is done
automatically during the search and store operation.
If the signal is weak or distorted, you may have to fine tune the channel manually.
1
Press the MENU (
2
Press the … or † button to select Channel, then press the ENTER (
button.
3
Press the … or † button to select Fine Tune, then press the ENTER (
button.
on.
n.
) button to display the menu.
)
TV
Channel
Area
: Asia/W.Europe
Auto Store
Manual Store
Channel Manager
Sort
Name
Fine Tune
Move
)
Enter
Return
Fine Tune
P 1 *
+3
4
To obtain a sharp and clear picture and good sound quality, press the œ or √
) button.
button until you reach the optimal setting. Press the ENTER (
➢
nd
5
To reset the fine tuning to 0, select Reset by pressing the … or †
button. Press the ENTER (
) button.
Press the EXIT button to exit.
➢
Fine Tune Store will change the colour of the Channel OSD (On Screen
Display) from White to Red and add the “*” mark.
n.
n.
l.
English - 15
Reset
Adjust
P 1 *
Mono
Save
Return
BN68-00955P-03Eng_0213
2/13/06
10:40 AM
Page 16
Changing the Picture Standard
You can select the type of picture which best corresponds to your viewing requirements.
TV
Picture
Mode
Size
Digital NR
DNIe Demo
PIP
: Dynamic
: 16:9
: On
: Off
Move
TV
Enter
Return
1
Press the MENU (
) button to display the menu.
2
Press the … or † button to select Picture, then press the ENTER (
button.
3
Press the ENTER (
4
Select the required mode by pressing the … or † button, then press the
ENTER (
) button.
)
) button twice.
Mode
Mode
Contrast
Brightness
Sharpness
Colour
Tint
G 50
Colour Tone
Reset
Move
Available modes: Dynamic, Standard, Movie, Custom
: Dynamic
Dynamic
Standard 100
50
Movie
75
Custom
55
R 50
: Cool 1
Enter
➢
5
The settings values may vary depending on the input source.
(ex. RF, Video, Component, PC, or HDMI)
Press the EXIT button to exit.
Return
➢
➢
You can select these options simply by pressing the P.MODE button
on the remote control.
◆ Choose Dynamic for viewing the TV during the day or when there is
bright light in the room.
◆ Choose Standard for the standard factory settings.
◆ Choose Movie when viewing the movie.
◆ Choose Custom if you want to adjust the settings according to personal
preference.
Customizing the Picture Settings
Your television has several setting options that allow you to control the picture quality.
TV
Picture
Mode
Size
Digital NR
DNIe Demo
PIP
: Dynamic
: 16:9
: On
: Off
Move
TV
Enter
Return
1
Press the MENU (
) button to display the menu.
2
Press the … or † button to select Picture, then press the ENTER (
button.
3
Press the ENTER (
4
Select the required mode by pressing the … or † button, then press the
ENTER (
) button.
) button twice.
Mode
Mode
Contrast
Brightness
Sharpness
Colour
Tint
G 50
Colour Tone
Reset
Move
Available modes: Dynamic, Standard, Movie, Custom
: Dynamic
100
50
Cool 2
75
Cool 1
55
Normal R 50
: Cool1
Warm 1
Warm 2
Enter
Return
5
Select the required option by pressing the … or † button, then press the
ENTER (
) button.
6
When you are satisfied with your setting, press the ENTER (
7
Press the EXIT button to exit.
◆ Contrast – Brightness – Sharpness – Colour – Tint (NTSC only)
◆ Contrast – Brightness – Colour : PC Mode
Press the œ or √ button until you reach the optimal setting.
◆ Colour Tone: Cool 2/Cool 1/Normal/Warm 1/Warm 2
◆ Reset: You can return to the factory defaults picture settings.
➢
)
The reset function is set for each picture mode and colour tone.
English - 16
) button.
BN68-00955P-03Eng_0213
2/13/06
10:40 AM
Page 17
Selecting the Picture Size
You can select the picture size which best corresponds to your viewing
requirements.
TV
1
Press the MENU (
2
Press the … or † button to select Picture, then press the ENTER (
button.
3
Press the … or † button to select Size, then press the ENTER (
4
Select the required option by pressing the … or † button, then press the
ENTER (
) button.
) button to display the menu.
Move
) button.
TV
Enter
Return
Size
16:9
Wide 4:3
Zoom
4:3
Move
Enter
Return
Press the EXIT button to exit.
➢
➢
➢
➢
al
: Dynamic
: 16:9
: On
: Off
)
Available options: 16:9, Wide 4:3, Zoom, 4:3
◆ 16:9: Sets the picture to 16:9 wide mode.
◆ Wide 4:3: Magnify the size of the picture more than 4:3.
Move the screen up/down using the … or † button after
selecting the
by pressing the √ or ENTER (
) button.
◆ Zoom: Magnify the size of the picture vertically on screen.
◆ 4:3: Sets the picture to 4:3 normal mode.
5
Picture
Mode
Size
Digital NR
DNIe Demo
PIP
You can change the picture size simply by pressing the P.SIZE button
on the remote control.
If you change the picture size when PIP is On, PIP will automatically
be turned Off.
Depending on the input source, the picture size options may vary.
The items available may differ depending on the selected mode.
Positioning and Sizing the screen using Zoom
◆ Resizing the screen using the Zoom enables the positioning and sizing of the screen to up/down direction
using the … or † button as well as the screen size.
◆ Move the screen up/down using the … or † button after selecting the
by pressing the œ or √ button.
◆ Resize the screen vertically using the … or † button after selecting the
by pressing the œ or √ button.
Digital NR / DNIe Demo
TV
1
Press the MENU (
) button to display the menu.
2
Press the … or † button to select Picture, then press the ENTER (
button.
3
Select the required option by pressing the … or † button, then press the
ENTER (
) button.
)
Picture
Mode
Size
Digital NR
DNIe Demo
PIP
Move
Available options: Digital NR, DNIe Demo
4
When you are satisfied with your setting, press the ENTER (
5
Press the EXIT button to exit.
: Dynamic
: 16:9
: On
: Off
Enter
Return
) button.
◆ Digital NR: On/Off
If the signal received by the television is weak, you can activate this feature to reduce any static and ghosting
that may appear on the screen.
◆ DNIe Demo: On/Off
This TV includes the DNIe function so as to provide a high visual quality.
If you set DNIe Demo to On, you can view an applied DNIe and a normal picture on the screen, for demonstration
purposes. Using this function, you can view the difference in the visual quality.
➢
➢
DNIeTM (Digital Natural Image engine)
This feature brings you more detailed image with 3D noise reduction, detail enhancement, contrast
enhancement and white enhancement. New image compensation Algorithm gives brighter, clearer, more
detailed image to you. DNIeTM technology will fit every signal into your eyes.
DNIe Demo is not available in PC mode.
English - 17
BN68-00955P-03Eng_0213
2/13/06
10:40 AM
Page 18
Viewing the Picture in Picture (PIP)
You can display a sub picture within the main picture. In this way you can watch TV program or monitor the video
input from any connected devices.
TV
Picture
Mode
Size
Digital NR
DNIe Demo
PIP
.
e
Move
TV
: Dynamic
: 16:9
: On
: Off
Enter
1
Press the MENU (
2
Press the … or † button to select Picture, then press the ENTER (
button.
3
Press the … or † button to select PIP, then press the ENTER (
4
Select the required option by pressing the … or † button, then press the
ENTER (
) button.
Return
Move
: On
: AV1
:
: P
1
Enter
)
) button.
Available options: PIP(On/Off), Source, Position, Programme
PIP
PIP
Source
Position
Programme
) button to display the menu.
Return
5
When you are satisfied with your setting, press the ENTER (
6
Press the EXIT button to exit.
) button.
◆ PIP: On/Off
You can activate or deactivate the PIP function.
➢
You can select these options simply by pressing the PIP button
on the remote control.
◆ Source: TV/AV1/AV2/S-Video
You can select a source of the sub-picture.
◆ Position: / / /
You can select a position of the sub-picture.
◆ Programme
You can select a channel of the sub-picture only when the Source is set to TV.
Easy functions of the remote control.
Buttons
Feature
PIP
Used to activate or deactivate the PIP function directly.
SOURCE
Used to assign a source of the sub picture (TV, AV1, AV2, or
S-Video).
POSITION
Used to move the sub picture counterclockwise.
P
Used to select a channel of the sub picture.
/
Table of PIP Settings
Main
TV
AV1
AV2
S-Video
Component1
Component2
HDMI
PC
Sub
TV
X
X
X
X
X
X
O
O
English - 18
X - This PIP combination is not available.
O - This PIP combination is available.
AV1
X
X
X
X
X
X
O
O
AV2
X
X
X
X
X
X
O
O
S-Video
X
X
X
X
X
X
O
X
PC
X
X
X
X
X
X
X
X
BN68-00955P-03Eng_0213
2/13/06
10:40 AM
Page 19
Sound Features
1
TV
) button to display the menu.
2
Press the … or † button to select Sound, then press the ENTER (
3
Select the required option by pressing the … or † button, then press the
ENTER (
) button.
4
When you are satisfied with your setting, press the ENTER (
5
Press the EXIT button to exit.
) button.
: Custom
: Off
: Off
: Off
Move
) button.
Enter
Return
< If Game Mode is On >
TV
Sound
Mode
Equalizer
SRS TSXT
Auto Volume
Internal Mute
Reset
◆ Mode: Standard/Music/Movie/Speech/Custom
You can select the type of special sound effect to be used when watching a
given broadcast.
➢
Sound
Mode
Equalizer
SRS TSXT
Auto Volume
Internal Mute
Reset
Available options: Mode, Equalizer, SRS TSXT, Auto Volume,
Internal Mute, Reset (If Game Mode is On)
.
V.
Press the MENU (
: Custom
: Off
: Off
: Off
Move
Enter
Return
You can select these options simply by pressing the S.MODE button
on the remote control.
◆ Equalizer: Balance/100Hz/300Hz/1kHz/3kHz/10kHz
The television has several settings which allow you to control the sound
quality.
➢
If you make any changes to these settings, the sound mode is
automatically switched to Custom.
TV
◆ SRS TSXT: On/Off
TruSurround XT is a patented SRS technology that solves the of playing 5.1
multichannel content over two speakers. TruSurround delivers a compelling,
virtual surround sound experience through any two-speaker playback
system, including internal television speakers. It is fully compatible with all
multichannel formats.
➢
➢
You can select these options simply by pressing the SRS(
button on the remote control.
Equalizer
R
L
Balance
Move
+
+
0
0
-
-
100Hz 300Hz 1kHz 3kHz 10kHz
Adjust
Return
)
TruSurround XT, SRS and
Symbol are trademarks
of SRS Labs, Inc. TruSurround XT technology is
incorporated under license from SRS Labs, Inc.
◆ Auto Volume: On/Off
Each broadcasting station has its own signal conditions, and so it is not easy to adjust the volume every time
the channel is changed. This feature lets you automatically adjust the volume of the desired channel by lowering
the sound output when the modulation signal is high or by raising the sound output when the modulation signal
is low.
◆ Internal Mute: On/Off
If you want to hear the sound through separate speakers, cancel the internal amplifier.
➢
The VOL +, VOL - and Mute buttons do not operate when the Internal Mute is set to On.
◆ Reset
If Game Mode is On, the Reset Sound function is activated. Selecting the Reset function after setting the equalizer
resets the equalizer setting to the factory defaults.
English - 19
BN68-00955P-03Eng_0213
2/13/06
10:40 AM
Page 20
Time Features
TV
Setup
Plug & Play
Language
Time
Game Mode
Blue Screen
Melody
PC
More
Move
TV
: English
: Off
: Off
: Off
Enter
1
Press the MENU (
2
Press the … or † button to select Setup, then press the ENTER (
) button.
3
Press the … or † button to select Time, then press the ENTER (
) button.
4
Select the required option by pressing the … or † button, then press the
ENTER (
) button.
Return
Available options: Clock Set, Sleep Timer, On Timer, Off Timer
Time
Clock Set
Sleep Timer
On Timer
Off Timer
Move
12 : 00 am
: Off
12 : 00 pm Off
12 : 00 pm Off
Enter
) button to display the menu.
Return
5
When you are satisfied with your setting, press the ENTER (
6
Press the EXIT button to exit.
) button.
◆ Clock Set
You can set the television clock so that the current time is displayed when
pressing the INFO button on the remote control. You must also set the time
if you wish to use the automatic on or off timers.
- Press the œ or √ button to select Hour, Minute, or am/pm.
Set these by pressing the … or † button.
➢
➢
You can set the hour and minute directly by pressing the numeric buttons
on the remote control.
In the event of a power interruption or the set being turned off at the
supply, the settings for the Clock will be lost.
◆ Sleep Timer
You can select a time period of between 30 and 180 minutes after which the
television automatically switches to standby mode.
- Select the preset time interval (Off, 30, 60, 90, 120, 150, or 180) for
staying on by pressing the … or † button.
➢
You can select these options simply by pressing the SLEEP button on
the remote control. If the sleep timer is not yet set, Off is displayed.
If it is already set, the remaining time before which the television
switches to standby mode is displayed.
◆ On Timer / Off Timer
You can set the On/Off timers so that the television will switch on or off automatically at the time you select.
☛ You must set the clock first.
- On Timer: Select Hour, Minute, am/pm, Programme, or Volume by pressing the œ or √ button.
Set these by pressing the … or † button.
To activate On Timer with the setting satisfied, set Activation to Yes by … or † button.
➢
You can set the hour and minute directly by pressing the numeric buttons on the
remote control.
- Off Timer: Select Hour, Minute, or am/pm by pressing the œ or √ button.
To activate Off Timer with the setting satisfied, set Activation to Yes by … or † button.
➢
☛
You can set the hour and minute directly by pressing the numeric buttons on the
remote control.
Auto Power Off
When you set the timer “On”, the television will eventually turn off, if no controls are operated for 3 hours after
the TV was turned on by timer. This function is only available in timer “On” mode and prevents overheating or
leakages, which may occur if a TV is on for too long (when you are on vacation, for example).
English - 20
on.
n.
ons
n.
n.
BN68-00955P-03Eng_0213
2/13/06
10:40 AM
Page 21
Language / Blue Screen / Melody / Energy Saving
1
2
3
Press the MENU (
TV
) button to display the menu.
Press the … or † button to select Setup, then press the ENTER (
) button.
Select the required option by pressing the … or † button, then press the
ENTER (
) button.
Available options: Language, Blue Screen, Melody, Energy Saving
4
When you are satisfied with your setting, press the ENTER (
5
Press the EXIT button to exit.
Setup
Plug & Play
Language
Time
Game Mode
Blue Screen
Melody
PC
More
Move
: English
: Off
: Off
: Off
Enter
Return
) button.
◆ Language
It is variable depending on the model. When you start using the television for the first time, you must select the language
which will be used for displaying menus and indications.
◆ Blue Screen: On/Off
If no signal is being received or the signal is very weak, a blue screen automatically replaces the noisy picture
background. If you wish to continue viewing the poor picture, you must set the Blue Screen to Off.
◆ Melody: On/Off
You can hear melody sound when the television is powered on or off.
◆ Energy Saving: Off/Low/Medium/High
This feature adjusts the screen brightness depending on the surrounding lighting
conditions.
Off: Switches off the Energy Saving mode.
Low: Operates in standard mode regardless of the surrounding illumination.
Medium: Enters Medium power saving mode regardless of the surrounding
illumination.
High: Enters maximum power saving mode regardless of the surrounding
illumination.
➢
You can select these options simply by pressing the E.SAVING button on the remote control.
Using Game Mode
When connecting to a game console such as PlayStationTM or XboxTM, you can enjoy a more realistic gaming
experience by selecting game menu.
1
Press the MENU (
2
Press the … or † button to select Setup, then press the ENTER (
3
Press the … or † button to select Game Mode, then press the ENTER (
button.
4
Select Off or On by pressing the … or † button, then press the ENTER (
button.
5
) button to display the menu.
TV
) button.
)
)
Setup
Plug & Play
Language
Time
Game Mode
Blue Screen
Melody
PC
More
Move
: English
: Off
: Off
: Off
Enter
Return
Press the EXIT button to exit.
➢
➢
➢
➢
To disconnect the game console and connect another external device, cancel game mode in the picture
menu.
If you display the TV menu in Game mode, the screen shakes slightly.
Game Mode is not available in TV mode.
If Game Mode is On :
◆ Picture Mode is automatically changed to Custom and users cannot change the mode.
◆ Sound Mode in the Sound menu is deactivated. Adjust the sound using the equalizer.
◆ The Reset Sound function is activated. Selecting the Reset function after setting the equalizer resets the
equalizer setting to the factory defaults.
English - 21
BN68-00955P-03Eng_0213
2/13/06
10:40 AM
Page 22
Screen Burn Protection
TV
To reduce the possibility of screen burn, this unit is equipped with screen burn
prevention technology. This technology enables you to set picture movement
up/down (Vertical Line) and side to side (Horizontal Dot). The Time setting allows
you to program the time between movement of the picture in minutes.
Setup
More
Energy Saving
: Off
Screen Burn Protection
Move
TV
Enter
Return
Screen Burn Protection
1
Press the MENU (
2
Press the … or † button to select Setup, then press the ENTER (
3
Press the … or † button to select Screen Burn Protection, then press
) button.
the ENTER (
4
Select the required option by pressing the … or † button, then press the
ENTER (
) button.
5
When you are satisfied with your setting, press the ENTER (
6
Press the EXIT button to exit.
Pixel Shift
All White
Signal Pattern
) button to display the menu.
) button.
Available options: Pixel Shift, All White, Signal Pattern
Move
TV
Enter
Return
) button.
Pixel Shift
Pixel Shift
Horizontal Dot
Vertical Line
Time
Move
: On
:4
:4
:4
Enter
Return
◆ Pixel Shift: Using this function, you can minutely move pixels on the PDP in horizontal or vertical direction to
minimize after image on the screen.
- Set Pixel Shift to On by pressing the … or † button, then press the ENTER (
- Select the required option by pressing the … or † button, then press the ENTER (
) button.
) button.
Available options: Horizontal Dot, Vertical Line, Time
➢
Optimum condition for pixel shift;
Horizontal Dot
Vertical Line
Time (minute)
4
4
4
◆ All White: This function helps remove after images on the screen by changing the colour of pixels to white.
Use this function when there are remaining after images or symbols on the screen especially when you
displayed a still image on the screen for a long time.
◆ Signal Pattern: This function helps remove after images on the screen by moving all the pixels on the PDP
according to a pattern. Use this function when there are remaining after images or symbols on the
screen especially when you displayed a still image on the screen for a long time.
➢
➢
➢
To remove after images on the screen, use either “All White” or “Signal Pattern” function.
Although both of the two functions remove after images on the screen, “Signal Pattern” is more effective.
The after image removal function has to be executed for a long time (approximately 1 hour) to effectively
remove after images on the screen.
If after image is not improved after the execution of the function, repeat the function again.
Press any button on the remote control to cancel this feature.
English - 22
s
on.
BN68-00955P-03Eng_0213
2/13/06
10:40 AM
Page 23
Setting up Your PC Software (Based on Windows XP)
The Windows display-settings for a typical computer are shown below. But the
actual screens on your PC will probably be different, depending upon your
particular version of Windows and your particular video card. But even if your
actual screens look different, the same, basic set-up information will apply in
almost all cases. (If not, contact your computer manufacturer or Samsung
Dealer.)
1
Right click the mouse on the Windows Desktop, then click on Properties.
The Display Properties will be displayed.
2
Click on Settings tab, then set the Display Mode with reference to the
Display Modes Table. You do not need to change the Colours settings.
3
Click on Advanced. A new settings dialog box will be displayed.
4
Click on the Monitor tab, then set the Screen refresh rate with reference to the Display Modes Table.
Set the Vertical Frequency and Horizontal Frequency individually if you can do so instead of setting the
Screen refresh rate.
5
Click on OK to close the window, then Click on OK button to the Display Properties window.
Automatic re-booting may commence at this moment.
s
Input Mode (PC)
Both screen position and size will vary depending on the type of PC monitor and its resolution.
The table below shows all of the display modes that are supported:
Video Signal
Resolution
(Dot X Line)
Vertical frequency
(Hz)
Horizontal frequency
(kHz)
Vertical
polarity
Horizontal
polarity
640 x 350
720 x 400
70.086
70.087
59.940
70.000
72.809
75.000
56.250
60.317
70.000
72.188
75.000
60.000
74.769
60.004
70.069
72.000
75.029
31.469
31.469
31.469
35.000
37.861
37.500
35.156
37.879
43.750
48.077
46.875
31.020
37.684
48.363
56.476
57.672
60.023
P
N
N
N/P
N
N
N/P
P
N/P
P
P
P
P
N
N
N/P
P
N
P
N
N/P
N
N
N/P
P
N/P
P
P
P
N
N
N
N/P
P
640 x 480
IBM PC / AT
Compatible
800 x 600
848 x 480
1024 x 768
(N: Negative / P: Positive)
◆
◆
◆
◆
The interlace mode is not supported.
The television might operate abnormally if a non-standard video format is selected.
480i/p, 576i/p, 720p, or 1080i is not available in PC mode.
The PC text quality is optimum in WVGA mode (848 x 480@60Hz).
English - 23
BN68-00955P-03Eng_0213
2/13/06
10:40 AM
Page 24
Setting the PC
➢
Preset to the PC mode by pressing the SOURCE (
TV
Setup
Plug & Play
Language
Time
Game Mode
Blue Screen
Melody
PC
More
: English
: Off
: Off
: Off
Move
TV
Enter
1
Press the MENU (
2
Press the … or † button to select Setup, then press the ENTER (
3
Press the … or † button to select PC, then press the ENTER (
4
Select the required option by pressing the … or † button, then press the
ENTER (
) button.
Return
TV
Enter
50
60
Move
TV
Enter
Enter
Auto Adjustment in progress
Please wait
Image Reset has completed.
5
When you are satisfied with your setting, press the ENTER (
6
Press the EXIT button to exit.
) button.
◆ Image Lock: Coarse/Fine
The purpose of picture quality adjustment is to remove or reduce picture noise.
If the noise is not removed by Fine-tuning alone, then adjust the frequency
as best as possible (coarse) and Fine-tune again.
After the noise has been reduced, re-adjust the picture so that it is aligned
on the center of screen.
Return
1
Press the … or † button to select Coarse or Fine, then press the
ENTER (
) button.
2
Press the œ or √ button to adjust the screen quality, vertical stripes may
) button.
appear or the picture may be blurry. Press the ENTER (
◆ Position:
Adjust the PC’s screen positioning if it does not fit the TV screen.
Position
Move
) button.
) button.
Return
Image Lock
Coarse
Fine
) button to display the menu.
Available options: Image Lock, Position, Auto Adjustment, Image Reset
PC
Image Lock
Position
Auto Adjustment
Image Reset
Move
) button.
1
Adjust the position by pressing the …/†/œ/√ button.
2
Press the ENTER (
) button.
Return
◆ Auto Adjustment:
Auto adjustment allows the PC screen of set to self-adjust to the incoming
PC video signal.
The values of fine, coarse and position are adjusted automatically.
◆ Image Reset:
You can replace all image settings with the factory default values.
Return
➢
You can select these options simply by pressing the PC button on the
remote control.
English - 24
on.
BN68-00955P-03Eng_0214
11:04 AM
Page 25
Teletext Feature (depending on the model)
Most television stations provide written information services via teletext.
The index page of the teletext service gives you information on how to
use the service. In addition, you can select various options to suit your
requirements by using the remote control buttons.
☛
Œ
For teletext information to be displayed correctly, channel reception
must be stable. Otherwise, information may be missing or some
pages may not be displayed.
(teletext on/mix)
Press to activate teletext mode after selecting the channel providing
the teletext service. Press it twice to overlap the teletext with the
current broadcasting screen.
et
se.
2/14/06
´
(sub-page)
Used to display the available sub-page.
ˇ
(size)
Press to display the double-size letters in the upper half of the
screen. For lower half of the screen, press it again.
To display normal screen, press it once again.
¨
(store)
Used to store the teletext pages.
ˆ
(hold)
Used to hold the display on a given page if the selected page is
linked with several secondary pages which follow on automatically.
To resume, press it again.
Ø
(page up)
Used to display the next teletext page.
∏
(mode)
Press to select the teletext mode (LIST/FLOF). If you press it in the
LIST mode, it switches into the List save mode. In the List save mode, you can save teletext page into list using
the
(store) button.
”
(page down)
Used to display the previous teletext page.
’
(index)
Used to display the index (contents) page at any time while you are viewing teletext.
˝
(reveal)
Used to display the hidden text (answers to quiz games, for example). To display normal screen, press it again.
Ô Coloured buttons (red/green/yellow/blue)
If the FASTEXT system is used by a broadcasting company, the different topics covered on a teletext page are
colour-coded and can be selected by pressing the coloured buttons. Press one of them corresponding to the
required. The page is displayed with other coloured information that can be selected in the same way.
To display the previous or next page, press the corresponding coloured button.

(cancel)
Used to display the broadcast when searching for a page.
Ò
(exit)
Exit from the teletext display (depending on the model)
➢
You can change teletext pages by pressing the numeric buttons on the
remote control.
continued...
English - 25
BN68-00955P-03Eng_0213
2/13/06
10:40 AM
Page 26
Teletext Feature (depending on the model)
The teletext pages are organized according to six categories:
Part
A
B
C
D
E
F
➢
➢
Contents
Selected page number.
Broadcasting channel identity.
Current page number or search indications.
Date and time.
Text.
Status information.
FASTEXT information.
Teletext information is often divided between several pages displayed in
sequence, which can be accessed by:
◆ Entering the page number
◆ Selecting a title in a list
◆ Selecting a coloured heading (FASTEXT system)
Press the TV button to exit from the teletext display.
English - 26
n
BN68-00955P-03Eng_0213
2/13/06
10:40 AM
Page 27
How to Install the Wall Mount Bracket
➢
This installation guide may be different from the PDP User’s manual.
Please refer to the proper installation guide for your product.
Installation Notes
◆ Contact a technician for installing the wall bracket.
◆ Samsung Electronics is not responsible for any damages to the product or harm to customers when the
installation is done by the customer.
◆ This product is for installing on cement walls. The product may not stay in place when installed on plaster or
wood.
◆ The package contents and parts supplied for the wall mount are subject to change without prior notice.
Mounting Kits
◆ Please use only the parts and components provided for wall mount installation.
Screws
ASSY-HINGE
Wall Mount Bracket
Plastic Hanger : 4 EA
1EA
LEFT :1EA RIGHT :1EA
Captive Screws
How to assemble the Wall Mount Bracket
1
SCREW : 4 EA
The wall mount bracket is delivered separately.
Please tighten the captive screw in the direction
of the arrow after assembling the bracket.
Install the Wall Mount Bracket after the screws
are securely inserted into the wall.
ASSY-HINGE
(LEFT)
Separate ASSY-HINGE
into Left and Right.
Wall Mount Bracket
ASSY-HINGE
(RIGHT)
Instructions on Securing the SET to the Wall Mount Bracket
➢ The exterior of the SET may be different than the picture. (Assembly and installation of the plastic hanger is
the same.)
1
Remove the screws from the back of the PDP.
2
☛
continued...
English - 27
Use the screw and assemble the plastic hanger.
(Please refer to the following picture.)
1 Please ask the installers to install the wall
mount bracket.
2 Please be sure to check if the plastic hanger is
completely secured on both the left and right
side after hanging the SET on the wall mount
bracket.
3 Please avoid catching your fingers while
installing and adjusting the angle.
4 Please tightly secure the wall mount bracket to
the wall to avoid injury from a falling SET.
BN68-00955P-03Eng_0213
2/13/06
10:40 AM
Page 28
How to Install the Wall Mount Bracket
3
Tighten the screws of the plastic hanger (shown
in picture 2) to the back side of the PDP.
4
Remove the Safety Pins. Fasten the 4 plastic
latches assembled at step (#) on the back side of
the PDP using the guide holes of the wall mount,
push (!) and hook (@) down to secure the PDP on
the wall mount as illustrated. Secure the PDP by
inserting the Safety Pins, not to fall from the wall
mount.
PDP panel
Wall attachment
panel bracket
Wall
How to Adjust Mounting Angle
➢ Please secure the mounting bracket on the wall surface after setting its angle at 0°
1
2
3
Secure the SET to the wall mount bracket.(Please refer to the
follow ing instructions.)
Set the angle by pulling the upper end of the SET attached to
bracket in the direction of the arrow. (Refer to the illustration
on the right.)
The angle can be adjusted from 0° to 15° by ±2°.
Hold onto the middle of the PDP to
adjust the angle (not the sides of
the PDP).
Connecting External Devices to the PDP
➢ To connect external devices such as a DVD or a Home Theater System to the PDP, please refer to following
instructions:
1
2
Be sure to remove the safety pins underneath the PDP.
➢ If the safety pins are not removed, the angle cannot be
adjusted. Any attempt to do so may cause damage to
the PDP.
Hold onto the bottom of the PDP and pull forward fully as
directed by the arrow as illustrated) to adjust the angle.
(0°~20° by 2°) Insert the Safety Pins to the front guide
holes on both sides as illustrated in figure @.
➢ Viewing the PDP after connecting the external devices
Remove the Safety Pins to adjust the angle to 0°, and
then secure the Safety Pins again.
For safety, be sure to secure the PDP using the safety
pins. If the safety pins are not used, the PDP may fall,
causing serious injury.
☛
English - 28
BN68-00955P-03Eng_0213
2/13/06
10:40 AM
Page 29
Troubleshooting
Before contacting the Samsung after-sales service, perform the following simple checks.
If you cannot solve the problem using the instructions below, note the model and serial number of the television and
contact your local dealer.
n
No sound or picture
◆ Check that the mains lead has been connected to a wall socket.
◆ Check that you have pressed the
(Power) button (On/Off) on the front panel or press the POWER ( )
button on the remote control.
◆ Check the picture contrast and brightness settings.
◆ Check the volume.
◆ Check if Internal Mute is set to ON.
Normal picture but no sound
◆ Check the volume.
◆ Check whether the volume MUTE button on the remote control has been pressed.
No picture or black and white picture
◆ Adjust the colour settings.
◆ Check that the broadcast system selected is correct.
Sound and picture interference
◆ Try to identify the electrical appliance that is affecting the television, then move it further away.
◆ Plug the television into a different mains socket.
Blurred or snowy picture, distorted sound
◆ Check the direction, location and connections of your aerial.
This interference often occurs due to the use of an indoor aerial.
Remote control malfunctions
◆ Replace the remote control batteries.
◆ Clean the upper edge of the remote control (transmission window).
◆ Check that the “+” and “–” ends of the batteries are inserted correctly.
◆ Check that the batteries are drained.
o
g
Screen is black and power indicator light blinks steadily
◆ On your computer check; Power, Signal Cable.
◆ The TV is using its power management system.
◆ Move the computer’s mouse or press any key on the keyboard.
◆
◆
◆
◆
On your equipment check (STB, DVD, etc) ; Power, Signal Cable.
The TV is using its power management system.
Press the Source button on the panel or remote control.
Turn the TV off and on.
e
s
y
English - 29
BN68-00955P-03Eng_0213
2/13/06
10:40 AM
Page 30
This page is intentionally
left blank.
BN68-00955P-03Eng_0213
2/13/06
10:40 AM
Page 31
This page is intentionally
left blank.
BN68-00955P-03Eng_0213
2/13/06
10:40 AM
Page 32
Contact SAMSUNG WORLD-WIDE
If you have any questions or comments relating to Samsung products,
please contact the SAMSUNG customer care centre.
Country
AUSTRALIA
CHINA
HONG KONG
INDIA
INDONESIA
JAPAN
MALAYSIA
PHILIPPINES
SINGAPORE
SOUTH AFRICA
TAIWAN
THAILAND
U.A.E
VIETNAM
Customer Care Centre 1300 362 603
800-810-5858, 010- 6475 1880
2862 6001
3030 8282, 1600 1100 11
0800-112-8888
0120-327-527
1800-88-9999
1800-10-SAMSUNG (7267864)
1800-SAMSUNG (7267864)
0860 7267864 (SAMSUNG)
0800-329-999
1800-29-3232, 02-689-3232
800SAMSUNG (7267864)
1 800 588 889
Web Site
www.samsung.com/au
www.samsung.com.cn
www.samsung.com/hk
www.samsung.com/in
www.samsung.com/id
www.samsung.com/jp
www.samsung.com/my
www.samsung.com/ph
www.samsung.com/sg
www.samsung.com/za
www.samsung.com/tw
www.samsung.com/th
www.samsung.com/mea
www.samsung.com/vn
BN68-00955P-03
Download PDF