Samsung | PPM63M7FS | Samsung Large Format Display 63M7F Benutzerhandbuch

Professional PDP
Display
(PLASMA DISPLAY PANEL)
PPM50M7F/PPM63M7F
Owner’s Instructions
Before operating the unit,
please read this manual thoroughly,
and retain it for future reference.
ON-SCREEN MENUS
Picture In Picture (PIP)
Energy Saving
SRS TruSurround XT
Digital Natural Image engine
Register your product at www.samsung.com/global/register
Record your Model and Serial number here for future reference.
▪ Model _______________ ▪ Serial No. _______________
BN68-01364B-00Eng.indd 1
2007-10-30 ¿ÀÀü 11:00:50
User Instructions
 Screen Image retention
Do not display a still image (such as on a video game or when hooking up a PC to this PDP Display)
on the plasma PDP Display panel for more than 2 hours as it can cause screen image retention.
This image retention is also known as “screen burn”. To avoid such image retention, reduce the
degree of brightness and contrast of the screen when displaying a still image.
 Height
The PDP Display can normally operate only under 2000m in height. It might abnormally function at a
place over 2000m in height, so do not install and operate there.
 Heat on the top of the PDP Display
The top side of the product may be hot after long periods of use as heat dissipates from the panel
through the vent hole in the upper part of the product.
This is normal and does not indicate any defect or operation failure of the product.
However, children should be prevented from touching the upper part of the product.
 The product is making a ‘cracking’ noise.
A ‘cracking’ noise may occur when the product contracts or expands due to a change of surrounding
environment such as temperature or humidity. This is normal and not a defect of the unit.
 Cell Defects
The PDP Display uses a panel consisting of 1,230,000(SD-level) to 3,150,000(HD-level) pixels which
require sophisticated technology to produce. However, there may be a few bright or dark pixels on
the screen. These pixels will have no impact on the performance of the product.
 Avoid operating the PDP Display at temperatures below 5°C(41°F)
 A still image displayed too long may cause permanent damage to the PDP Panel.
Watching the PDP Display in 4:3 format for a long period of time may leave
traces of borders displayed on the left, right and center of the screen caused by
the difference of light emission on the screen.
Playing a DVD or a game console may cause similar effect to the screen.
Damage caused by the above effect are not covered by the Warranty.
 After image on the Screen.
Displaying still images from Video games and PC for longer than a certain period of time may
produce partial afterimages.
To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when displaying still images for a long
time.
 Warranty
- Warranty does not cover any damage caused by image retention.
- Burn-in is not covered by the warranty.
 Installation
Be sure to contact an authorized service center, when installing your PDP Display in a location with
heavy dust, high or low temperatures, high humidity, chemical substance and where it operates for 24
hours such as the airport, the train station or etc.
Failure to do so may cause a serious damage to your PDP Display.
Installing the product in an airtight place may shorten the lifetime of the product.
© 2007 Samsung Electronics Co., Ltd. All rights reserved.
English - 2
BN68-01364B-00Eng.indd 2
2007-10-30 ¿ÀÀü 11:00:51
Contents
General Information





PC Display
User Instructions ............................................. 2
Checking Parts................................................ 4
Control Panel ................................................. 5
Connection Panel............................................ 6
Viewing the Remote Control .......................... 7
Operation
 Switching Your PDP Display On and Off ......... 8
 Installing the Display Vertically........................ 9
 Before Using the Video Wall and the
Multiple Display Control function..................... 9
 Connecting Speakers.................................... 11
 Viewing the Menus ........................................ 12
 Freezing the Current Picture ......................... 12
 Displaying the Setting Information ................ 12
 Viewing an External Signal Sources ............. 13
 Editing Device Names................................... 13
 Setting up Your PC Software
(Based on Windows XP) ............................... 31
 Display Modes .............................................. 32
 Setting the PC ............................................... 33
 Setting the Home Theatre PC ....................... 34
Appendix




Wall Mount Kit Specifications (VESA) ........... 34
Using the Stand-Base ................................... 35
Troubleshooting ............................................ 36
Specifications ................................................ 37
Picture Control





Changing the Picture Standard ..................... 14
Customizing the Picture Settings .................. 14
Configuring Detailed Settings on the Picture .. 15
Selecting the Picture Size ............................. 16
Digital NR / Active Color / DNIe / Movie Plus ... 17
Sound Control
 Sound Features ............................................ 18
Function Description
 Time Features ............................................... 20
 Language / Blue Screen / Melody /
Energy Saving / HDMI Black Level ............... 21
 Setting the Panel Button Lock....................... 22
 Setting the Remote Control Button Lock....... 22
 Setting Up Your Personal ID Number ........... 23
 Setting the MDC (Multiple Display Control) .. 24
 Setting the Multiple Screen ........................... 25
 Selecting the Fan .......................................... 26
 Using the Game Mode .................................. 27
 Viewing the Picture in Picture (PIP) .............. 28
 Screen Burn Protection ................................. 29
 Setting the Screen Burn Protection Timer..... 30
☛
➢
Important
Note
Symbols
Press
English - 3
BN68-01364B-00Eng.indd 3
2007-10-30 ¿ÀÀü 11:00:51
Checking Parts
Owner’s Instructions
Remote Control/
AAA Batteries
Power Cord
Stand-Base (2EA) /
Screws (4EA)
(PPM50M7F)
Ferrite Cores
PC Cable
Warranty Card/
Registration Card/
(Not available in all locations)
Sold Separately
S-Video Cable
Component Cables
Audio Cables
HDMI/DVI Cable
PC Audio Cable
HDMI Cable
Video Cable
Ferrite Core (Speaker Wire, Power Cord)
➢ The
ferrite cores are used to shield the cables from
interference.
When connecting a cable, open the ferrite core and clip it
around the cable near the plug.
Speaker Wire
Power Cord
English - 4
BN68-01364B-00Eng.indd 4
2007-10-30 ¿ÀÀü 11:00:54
Control Panel
Front Panel
➢ The product color and shape may vary depending on the model.
1 SOURCE( )
Displays a menu of all of the available input
sources (AV, S-Video, Component, PC1,
PC2, DVI, and HDMI).
In the on-screen menu, use this button as
you would use the ENTER button on the
remote control.
➢
2 MENU
Press to see the on-screen menu of your PDP
Display’s features.
3
4
− VOL +
Press to increase or decrease the volume.
In the on-screen menu, use the − VOL +
buttons as you use the + and − buttons on the
remote control.
SEL
Control the cursor in the menu.
5
(Power) button
Press to turn the PDP Display on and off.
6 Power Indicator
Blinks and turns off when the power is on and
lights up in stand-by mode.
7 Remote Control Sensor
Aim the remote control towards this spot on
the PDP Display.
You can use the
SEL
buttons
to switch on the PDP Display when it
is in standby mode depending on the
model.
The − VOL + and
SEL
buttons have the same function as
the ▲/▼/◄/► buttons on the remote
control.
If the remote control no longer works
or you have misplaced it, you can use
the controls on the panel of the PDP
Display.
➢
➢
➢
English - 5
BN68-01364B-00Eng.indd 5
2007-10-30 ¿ÀÀü 11:00:56
Connection Panel
Rear Panel
2 3 4
5
6
7
8
9
0
!
1
1
PPM50M7F
PPM63M7F
or
or
or
➢ The product color and shape may vary depending on the model.
☛
 Whenever you connect an audio or video system to your set, ensure that all elements are
switched off.
 When connecting an external device, match the color of the connection terminal to the cable.
1 POWER IN
Connect the supplied power cord.
2 EXT SPEAKER (8Ω)
Connect external speakers.
3 DVI/PC/HDMI AUDIO IN
Connect to the audio output jack on your
PC or DVI.
AUDIO is an audio input jack for PC1 and
PC2 modes.
4 DVI IN
Connect to the video output jack for device
with DVI output.
5 HDMI IN
Connect to the HDMI jack of a device with
HDMI output.
-This input can also be used as a DVI
connection with separate analog audio
inputs. An optional HDMI/DVI cable will be
necessary to make this connection.
-When using an optional HDMI/DVI adapter,
the DVI analog audio inputs on your PDP
Display allow you to receive left and right
audio from your DVI device.
6 PC IN1/PC OUT1
- PC IN1: Connect to the video output jack on
your PC.
- PC OUT1: Connect to the video input jack on
external devices.
➢
7 PC IN2 (BNC)
Connect for RGB HV video signal input from
the PC.
“PC Mode” from this page onward means
PC1/PC2 mode using RGB1(PC1) and
RGB2(PC2).
8 RS-232C
- IN: Used for the MDC function when
connecting PC or RS-232C output of
another PDP Display.
- OUT: Used for the MDC function when
connecting with RS-232C input of
another PDP Display.
For further details about connections,
refer to Page 10.
9 COMPONENT IN
Video (Y/PB/PR) and audio (L/R) inputs for
component.
0 AV (VIDEO/AUDIO L/R)
- IN: Video and audio inputs for external
devices, such as a camcorder or VCR.
- OUT: Outputs for external devices.
! S-VIDEO IN
Video input for external devices with an
S-Video output, such as a camcorder or VCR.
➢
➢
English - 6
BN68-01364B-00Eng.indd 6
2007-10-30 ¿ÀÀü 11:01:00
Viewing the Remote Control
➢
1
2
3
4
5
6
7
8
9
0
!
@
The performance of the remote control may be affected by bright light.
PDP display on
Direct channel selection
Not available
Volume increase
Temporary sound switch-off
Volume decrease
Returns to the previous
menu
Menu display
Move to the required menu
option/Adjust an option value
respectively
Picture effect selection
Auto adjustment in pc mode
PIP functions:
- PIP activation or
deactivation (PIP)
- Select a position of the
sub-picture (POSITION)
#
$
%
^
&
*
(
)
a
b
c
d
PDP display off
Picture still
Next channel
External input selection
Previous channel
Information display
Exit from any display
Confirm your choice (store
or enter)
Sound effect selection
Picture size
Multiple display control
Screen effect selection
(burning protection)
Continued...
English - 7
BN68-01364B-00Eng.indd 7
2007-10-30 ¿ÀÀü 11:01:02
Installing Batteries in the Remote Control
1
2
3
Remove the cover on the rear of the remote control by
pressing the symbol ( ) downwards and then pulling firmly to
remove it.
Install two AAA size batteries.
 Make sure to match the “+” and “–” ends of the
batteries with the diagram inside the compartment.
 Do not mix battery types, i.e. alkaline and manganese.
Replace the cover by aligning it with the base of the remote
control and pressing it back into place.
Remove the batteries and store them in a cool and dry
place if you won’t be using the remote control for a long
time. The remote control can be used up to about 23 feet
from the PDP Display. (Assuming typical PDP Display
usage, the batteries last for about one year.)
➢
➢
remote control doesn’t work! Check the following:
➢ If1.the
Is the PDP Display power on?
2. Are the plus and minus ends of the batteries reversed?
3. Are the batteries drained?
4. Is there a power cut, or is the power cord unplugged?
5. Is there a special fluorescent light or a neon sign nearby?
Switching Your PDP Display On and Off
The mains lead is attached to the rear of the PDP Display.
1
2
3
Plug the mains lead into an appropriate socket.
The main voltage is indicated on the rear of the PDP Display and the frequency is 50 or 60Hz.
Press the (Power) button (On/Off) on the front of the PDP Display or press the ON button on the
remote control to switch the PDP Display on.
To switch the PDP Display off, press the (Power) button (On/Off) on the front of the PDP Display or
press the OFF button on the remote control.
➢
English - 8
BN68-01364B-00Eng.indd 8
2007-10-30 ¿ÀÀü 11:01:02
Installing the Display Vertically
 Samsung shall not be liable for damages caused by installing the product at the different
direction from the figure below.
You can install the PDP Display vertically. In this case, the fan automatically works. If you wish to stop the
fan, position the PDP Display horizontally and then set Fan to Off in the Function menu.
Please use the wall attachment panel exclusively when installing vertically. And you have to put the
bottom of the PDP Display with menu buttons on the left when viewed from front.
Before Using the Video Wall and the Multiple Display Control
function
1
2
Please create ID for each PDP Display before
installing them close together. It may be difficult to
create IDs when operating the remote control for
PDPs that are installed close to each other.
For details about Video Wall configuration and
operation, refer to “Setting the Multiple Screen” on
page 25.
Example for 2x2 Video Wall function
Continued...
English - 9
BN68-01364B-00Eng.indd 9
2007-10-30 ¿ÀÀü 11:01:03
Example for 2x2 Video Wall connections
Rear of the PDP Display
Distributor
Y/PB/PR
2
1
L/R
DVD
Rear of the PDP Display
1 Connect the Component IN port of the
distributor and the Component OUT port
of the device that supports the Component
interface such as a DVD player using the
Component video and audio cables.
2 Connect the Component IN port on
the rear panel of each PDP and the
Component OUT port of the distributor
using the Component video and audio
cables. (A distributor has multiple
Component OUT ports.)
Example for Multiple Display Control connections
➢
You can connect a Composite (Video) without a
distributor as you would connect a PC.
 Select ID input on the menu. Use the numeric
buttons to enter the ID for PDP Display
adjustment. You can operate the remote
control only for the PDP Display that has been
selected.
 For details about Multiple Display Control, refer
to “Setting the MDC (Multiple Display Control)”
on page 24.
English - 10
BN68-01364B-00Eng.indd 10
2007-10-30 ¿ÀÀü 11:01:08
Connecting Speakers
➢ Speakers are optional. You have to purchase the speakers additionally.
1
Remove the screws on the rear of the PDP Display.
PPM50M7F
2
PPM63M7F
Hang the two “T” shaped hangers on the square holes on the rear of the PDP Display.
PPM50M7F
3
PPM63M7F
Tighten the PDP Display and the speaker bracket using the screws removed from the PDP Display.
PPM50M7F
PPM63M7F
moving your PDP Display, do NOT hold the speaker connected to your PDP Display. It may
➢ When
damage the bracket clamping the speaker and your PDP Display together and result in a drop of your
PDP Display and a risk of personal damage and injury.
English - 11
BN68-01364B-00Eng.indd 11
2007-10-30 ¿ÀÀü 11:01:19
Viewing the Menus
1
2
3
4
5
Press the MENU button.
The main menu is displayed on the screen.
Its left side has five icons: Picture, Sound, Function, Setup,
and Input.
Press the ▲ or ▼ button to select one of the icons.
Press the ENTER button to access the icon’s sub-menu.
Press the ▲ or ▼ button to move to items in the menu.
Press the ENTER button to enter items in the menu.
Press the ▲/▼/◄/► button to change the selected items.
Press the RETURN button to return to the previous menu.
Press the EXIT button to exit from the menu.
Picture
Mode
: Dynamic
Contrast
Brightness
Sharpness
Color
G 50
Tint
: Cool1
Color Tone
Detailed Settings

100
45
75
55
R 50


 More
Move
Enter
Exit
Freezing the Current Picture
You can freeze the picture when watching a moving picture
simply by pressing the “STILL” button. To return to normal
viewing, press it again.
PIP mode, Still function will be applied to the main and sub
➢ Inpicture
at the same time.
Displaying the Setting Information
can view the setting status you select by pressing the
➢ You
INFO button on the remote control.
AV
Picture
Sound
SRS TS XT
−− : −−
: Dynamic
: Custom
: Off
English - 12
BN68-01364B-00Eng.indd 12
2007-10-30 ¿ÀÀü 11:01:22
Viewing an External Signal Sources
You can switch between viewing signals from connected
equipment, such as a VCR, DVD, Set-Top Box, and the PDP
Display source.
1
2
3
4
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Input, then press the
ENTER button.
Press the ENTER button again to select Source List.
Press the ▲ or ▼ button to select the signal source, then
press the ENTER button.
Available signal sources: AV, S-Video, Component, PC1,
PC2, DVI, HDMI
Only the connected devices can be selected.
➢
Input
Source List
Edit Name
Move
: AV


Enter
Return
Source List
AV
S-Video
Component
PC1
PC2
DVI
HDMI
Move
: −−−−
: −−−−
: −−−−
: −−−−
: −−−−
: −−−−
: −−−−
Enter
Return
can select these options simply by pressing the SOURCE
➢ You
button on the remote control.
the INFO button on the remote control to see the current
➢ Press
input source.
Editing Device Names
You can give a name to the external source.
1
2
3
4
5
6
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Input, then press the
ENTER button.
Press the ▲ or ▼ button to select Edit Name, then press the
ENTER button.
Press the ▲ or ▼ button to select the external source to be
edited, then press the ENTER button.
Select the required device by pressing ▲ or ▼, then press the
ENTER button.
Available device names: VCR, DVD, D-VHS, Cable STB,
HD STB, Satellite STB, AV Receiver, DVD Receiver, Game,
Camcorder, DVD Combo, DHR (DVD HDD Recorder), PC
Press the EXIT button to exit.
Input
Source List
Edit Name
Move
: AV


Enter
Return
Edit Name
AV
S-Video
Component
PC1
PC2
DVI
HDMI
Move
: −−−− −−−−
: −−−− VCR
: −−−− DVD
: −−−−D-VHS
: −−−−
Cable STB
: −−−−HD STB
: −−−−
Satellite STB
▼
Enter
Return
English - 13
BN68-01364B-00Eng.indd 13
2007-10-30 ¿ÀÀü 11:01:24
Changing the Picture Standard
You can select the type of picture which best corresponds to
your viewing requirements.
1
2
3
4
Picture
Mode
: Dynamic
Contrast
Brightness
Sharpness
Color
G 50
Tint
: Cool1
Color Tone
Detailed Settings
Press the MENU button to display the menu.
Press the ENTER button to select Picture.
Press the ENTER button again to select Mode.
Select the required mode by pressing the ▲ or ▼ button,
then press the ENTER button.
Available modes: Dynamic, Standard, Movie
The settings values may vary depending on the input
source. (ex. Video, Component, PC, or HDMI)
Press the EXIT button to exit.
➢
100
45
75
55
R 50


 More
Move
➢
5

Enter
Return
Picture
Dynamic 
Mode
: Dynamic
Standard
Contrast
Movie
Brightness
Sharpness
Color
G 50
R
Tint
Color Tone
: Cool1
Detailed Settings
 Choose Dynamic for viewing the PDP Display during the
day or when there is bright light in the room.
 Choose Standard for general PDP Display watching
mode.
 Choose Movie when viewing the movie.
100
45
75
55
50
 More
Move
Enter
Return
You can select these options simply by pressing the P.MODE
➢ button
on the remote control.
Customizing the Picture Settings
Your PDP Display has several setting options that allow you to
control the picture quality.
1
2
3
4
5
6
7
Press the MENU button to display the menu.
Press the ENTER button to select Picture.
Press the ENTER button again to select Mode.
Select the required mode by pressing the ▲ or ▼ button,
then press the ENTER button.
Available modes: Dynamic, Standard, Movie
Select the required option by pressing the ▲ or ▼ button,
then press the ENTER button.
When you are satisfied with your setting, press the ENTER
button.
Press the EXIT button to exit.
 Contrast – Brightness – Sharpness – Color – Tint
In AV, S-Video modes of the PAL system, you cannot use
the Tint function.
Contrast – Brightness – Color Tone : PC Mode
Press the ◄ or ► button until you reach the optimal setting.
 Color Tone: Cool2/Cool1/Normal/Warm1/Warm2
When the picture mode is set to Dynamic or Standard,
Warm1 and Warm2 cannot be selected.
 Reset: Cancel/OK
Select OK. You can return to the factory defaults picture settings.
The reset function is set for each picture mode and color tone.
➢
➢
Picture
Mode
: Dynamic
Contrast
Brightness
Sharpness
Color
G 50
Tint
: Cool1
Color Tone
Detailed Settings

100
45
75
55
R 50


 More
Move
Enter
Contrast
Return
100
Move
Adjust
Return
Picture
Mode
: Dynamic
Contrast
Brightness
Sharpness
Color
G 50
Tint
Cool2 R
: Cool1Cool1
Color Tone
Detailed Settings
Normal
Warm1
Warm2
 More
Move
Enter
100
45
75
55
50
Return
➢
English - 14
BN68-01364B-00Eng.indd 14
2007-10-30 ¿ÀÀü 11:01:25
Configuring Detailed Settings on the Picture
You can set detail picture settings.
1
2
3
4
5
6
➢
➢
Picture
Press the MENU button to display the menu.
Press the ENTER button to select Picture.
Press the ▲ or ▼ button to select Detailed Settings, then
press the ENTER button.
Select the required option by pressing the ▲ or ▼ button,
then press the ENTER button.
Available options: Black Adjust, Dynamic Contrast,
Gamma, White Balance, My Color Control,
Edge Enhancement, Color Space, xvYCC.
When you are satisfied with your setting, press the ENTER
button.
Press the EXIT button to exit.
When the picture mode is set to Movie or Standard, Detailed
Settings can be selected.
If DNIe is Off or Demo, the Detailed Settings cannot be
selected when the Picture mode is in Standard mode.
Mode
: Movie
Contrast
Brightness
Sharpness
Color
G 50
Tint
: Warm2
Color Tone
Detailed Settings

80
45
10
53
R 50


 More
Move
Enter
Return
Detailed Settings
Black Adjust
Dynamic Contrast
Gamma
White Balance
My Color Control
Edge Enhancement
Color Space
xvYCC
Move
: Off
: Off
:0








: Off
: Auto
: Off
Enter
Return
 Black Adjust: Off/Low/Medium/High
You can directly select the black level on the screen to adjust the screen depth.
 Dynamic Contrast: Off/Low/Medium/High
You can adjust the screen contrast so that the optimal contrast is provided.
 Gamma: -3 ~ +3
You can adjust the middle brightness of pictures.
Press the ◄ or ► button until you reach the optimal setting.
 White Balance: R-Offset/G-Offset/B-Offset/R-Gain/G-Gain/B-Gain/Reset
You can adjust the color temperature for more natural picture colors.
R-Offset/G-Offset/B-Offset/R-Gain/G-Gain/B-Gain:
Changing the adjustment value will refresh the adjusted screen.
Select the required option by pressing the ▲ or ▼ button, then press the ENTER button.
Press the ◄ or ► button until you reach the optimal setting.
Reset: The previously adjusted white balance will be reset to the factory defaults.
 My Color Control: Pink/Green/Blue/White/Reset
This setting can be adjusted to suit your personal preferences.
Pink/Green/Blue/White: Changing the adjustment value will refresh the adjusted screen.
Select the required option by pressing the ▲ or ▼ button, then press the ENTER button.
Press the ◄ or ► button until you reach the optimal setting.
When running the My Color Control feature, the current picture is captured as a still image
before being displayed on the screen.
Reset: The previously adjusted colors will be reset to the factory defaults.
 Edge Enhancement: Off/On
You can emphasize object boundaries.
 Color Space: Auto/Wide
You can set the color reproduction space for the input signal to Auto or Wide.
 xvYCC: Off/On
Setting the xvYCC mode to On increases detail and color space when watching movies from an
external device (ie. DVD player) connected to the HDMI or Component IN jacks. You must set the
Picture Mode to Movie to enjoy this feature.
The xvYCC function works only in Component or HDMI mode.
If xvYCC function is active, PIP cannot be selected.
➢
➢
➢
English - 15
BN68-01364B-00Eng.indd 15
2007-10-30 ¿ÀÀü 11:01:26
Selecting the Picture Size
You can select the picture size which best corresponds to
your viewing requirements.
1
2
3
4
Press the MENU button to display the menu.
Press the ENTER button to select Picture.
Press the ▲ or ▼ button to select Size, then press the
ENTER button.
Select the required option by pressing the ▲ or ▼ button,
then press the ENTER button.
Available options: 16 : 9, Wide Zoom, Zoom, 4 : 3, Just Scan
 16 : 9: Sets the picture to 16:9 wide mode.
 Wide Zoom: Magnify the size of the picture more than
4:3. Move the screen up/down using the ▲ or ▼ button
after selecting the by pressing the ► or ENTER
button.
 Zoom: Magnify the size of the picture vertically on
screen.
 4 : 3: Sets the picture to 4:3 normal mode.
 Just Scan: Displays the input scenes as they are without
any cutoff when HDMI 720p, 1080i, 1080p signals are
input.
With the HDMI Just Scan picture size, depending on the AV
devices, the screen may be cut off or a specific appears on
the screen.
Press the EXIT button to exit.
Picture
 More
Size
Digital NR
Active Color
DNIe
Movie Plus
Reset
Move
:4:3
: Off
: On
: On
: On
: OK
Enter






Return
Size
16 : 9
Wide Zoom
Zoom
4:3
Just Scan
Move
Enter
Return
➢
5
can change the picture size simply by pressing the P.SIZE button on the remote control.
➢ You
on the input source, the picture size options may vary.
➢ Depending
items available may differ depending on the selected mode.
➢ The
➢ PC and DVI modes, only 16:9, 4:3 modes can be selected.
Positioning and Sizing the screen using Zoom
 Resizing the screen using the Zoom enables the positioning and sizing of the screen to up/down
direction using the ▲ or ▼ button as well as the screen size.
 Move the screen up/down using the ▲ or ▼ button after selecting the by pressing the ◄ or ►
button.
 Resize the screen vertically using the ▲ or ▼ button after selecting the by pressing the ◄ or ►
button.
English - 16
BN68-01364B-00Eng.indd 16
2007-10-30 ¿ÀÀü 11:01:27
Digital NR / Active Color / DNIe / Movie Plus
1
2
3
4
5
Press the MENU button to display the menu.
Press the ENTER button to select Picture.
Select the required option by pressing the ▲ or ▼ button, then
press the ENTER button.
Available options: Digital NR, Active Color, DNIe,
Movie Plus
When you are satisfied with your setting, press the ENTER
button.
Press the EXIT button to exit.
Picture
 More
Size
Digital NR
Active Color
DNIe
Movie Plus
Reset
Move
:4:3
: Off
: On
: On
: On
: OK
Enter






Return
 Digital NR: Off/Low/Medium/High/Auto
If the signal received by the PDP Display is weak, you can activate this feature to reduce any static
and ghosting that may appear on the screen.
 Active Color: Off/On
If you turn on this option, the colors of the sky and grass will be stronger and clearer for a more vivid
on-screen picture.
This function is not available in PC mode.
This function is available in Dynamic mode.
 DNIe: Off/Demo/On
This PDP Display includes the DNIe function so as to provide a high visual quality. If you set DNIe to
on, you can view the screen with the DNIe feature activated. If you set the DNIe to Demo, you can
view the applied DNIe and normal pictures on the screen, for demonstration purposes. Using this
function, you can view the difference in the visual quality.
DNIeTM (Digital Natural Image engine)
This feature brings you more detailed image with 3D noise reduction, detail enhancement,
contrast enhancement and white enhancement. New image compensation Algorithm gives
brighter, clearer, more detailed image to you. DNIeTM technology will fit every signal into your
eyes.
This function is not available in PC mode.
When the picture mode is set to Movie, DNIe cannot be selected.
 Movie Plus: Off/On
You can view more natural skin and clear text even in fast moving scenes.
This function is not supported in the Wide Zoom,Zoom and Just Scan mode.
In Movie Plus, HDMI (1080p), PC, and DVI modes are deactivated.
➢
➢
➢
➢
➢
➢
➢
English - 17
BN68-01364B-00Eng.indd 17
2007-10-30 ¿ÀÀü 11:01:28
Sound Features
1
2
3
4
5
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Sound, then press the
ENTER button.
Select the required option by pressing the ▲ or ▼ button, then
press the ENTER button.
Available options: Mode, Equalizer, SRS TS XT, Auto Volume,
Internal Mute, Sound Select, Reset
When you are satisfied with your setting, press the ENTER
button.
Press the EXIT button to exit.
Sound
Mode
Equalizer
SRS TS XT
Auto Volume
Internal Mute
Sound Select
Reset
Move
: Custom
: Off
: Off
: Off
: Main
Enter






Return
< If Game Mode is On >
Sound
 Mode: Standard/Music/Movie/Speech/Custom
Mode
: Custom

You can select the type of special sound effect to be used
Equalizer

when watching a given broadcast.
SRS TS XT
: Off

Auto
Volume
:
Off

 Choose Standard for the PDP Display standard
Internal Mute
: Off

factory settings.
Sound Select
: Main

 Choose Music when watching the music videos or
Reset
concerts.
 Choose Movie when watching movies.
Move
Enter
Return
 Choose Speech when watching a show that is mostly
dialog(i.e., news).
 Choose Custom to recall your personalized settings.
You can select these options simply by pressing the
S.MODE button on the remote control.
 Equalizer: Balance/100Hz/300Hz/1kHz/3kHz/10kHz
The PDP Display has several settings which allow you to control
Equalizer
the sound quality.
 R/L Sound Balance Adjustment:
To adjust the sound balance of the R/L speakers.
R
+
+
 Bandwidth Adjustment(100Hz, 300Hz, 1kHz, 3kHz,
0
0
10kHz): To adjust the level of different bandwidth
L
frequencies.
Balance 100Hz 300Hz 1kHz 3kHz 10kHz
If you make any changes to these settings, the sound
standard is automatically switched to Custom.
Move
Adjust
Return
 SRS TS XT: Off/On
TruSurround XT is a patented SRS technology that solves the
problem of playing 5.1 multichannel content over two speakers.
TruSurround delivers a compelling, virtual surround sound experience through
any two-speaker playback system, including internal PDP Display speakers.
It is fully compatible with all multichannel formats.
TruSurround XT, SRS and
Symbol are trademarks of SRS Labs, Inc.
TruSurround XT technology is incorporated under license from SRS Labs, Inc.
➢
➢
➢
➢
➢
Continued...
English - 18
BN68-01364B-00Eng.indd 18
2007-10-30 ¿ÀÀü 11:01:28
 Auto Volume: Off/On
Each broadcasting station has its own signal conditions, and so it is not easy to adjust the volume
every time the channel is changed. This feature lets you automatically adjust the volume of the
desired channel by lowering the sound output when the modulation signal is high or by raising the
sound output when the modulation signal is low.
 Internal Mute: Off/On
If you want to hear the sound through separate speakers, cancel the internal amplifier.
The VOL +, VOL -, S.MODE, and MUTE buttons do not operate when the Internal Mute is set to
On.
 Sound Select: Main/Sub
When the PIP feature is activated, you can listen to the sound of the sub (PIP) picture.
− Main: Used to listen to the sound of the main picture.
− Sub: Used to listen to the sound of the sub picture.
 Reset
If Game Mode is On (refer to page 27), the Reset Sound function is activated. Selecting the Reset
function after setting the equalizer resets the equalizer setting to the factory defaults.
➢
English - 19
BN68-01364B-00Eng.indd 19
2007-10-30 ¿ÀÀü 11:01:29
Time Features
1
2
3
4
5
6
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Setup, then press the
ENTER button.
Press the ▲ or ▼ button to select Time, then press the
ENTER button.
Select the required option by pressing the ▲ or ▼ button,
then press the ENTER button.
Available options: Clock Set, Sleep Timer, Timer1, Timer2,
Timer3
When you are satisfied with your setting, press the
ENTER button.
Press the EXIT button to exit.
Setup
Screen Burn Protection
Language
: English
Time
Game Mode
: Off
Blue Screen
: Off
Melody
: Off
PC
Home Theatre PC : Off








 More
Move
Enter
Return
Time
Clock Set
Sleep Timer
Timer1
Timer2
Timer3
: −− : −−
: Off
: Inactivated
: Inactivated
: Inactivated





 Clock Set
You can set the PDP Display clock so that the current time
is displayed when pressing the INFO button on the remote
control. You must also set the time if you wish to use the
automatic on or off timers.
Move
Enter
Return
− Press the ◄ or ► button to select Month, Day, Year, Hour,
or Minute.
Set these by pressing the ▲ or ▼ button.
You can set the Month, Day, Year, Hour, and Minute directly by pressing the numeric buttons
on the remote control.
In the event of a power interruption or the set being turned off at the supply, the settings for the
Clock will be lost.
 Sleep Timer
You can select a time period of between 30 and 180 minutes after which the PDP Display
automatically switches to standby mode.
− Select the preset time interval (Off, 30, 60, 90, 120, 150, 180) for staying on by pressing the
▲ or ▼ button.
 Timer1 / Timer2 / Timer3
You can set the On/Off timers so that the PDP Display will switch on or off automatically at the time
you select.
You must set the clock first.
− Press the ◄ or ► button to select the required item below.
Press the ▲ or ▼ button to adjust to the setting satisfied.
On Time : Select hour, minute, and No/Yes. (To activate timer with the setting satisfied, set to
Yes.)
Off Time : Select hour, minute, and No/Yes. (To activate timer with the setting satisfied, set to
Yes.)
Repeat : Select Once, Everyday, Mon - Fri, Mon - Sat, or Sat - Sun.
Volume : Select the required volume level.
Source : Select the required external device.
You can set the hour, and minute directly by pressing the number buttons on the remote control.
➢
➢
☛
➢
Power Off
☛ Auto
When you set the timer “On”, the PDP Display will eventually turn off, if no controls are operated for 3
hours after the PDP Display was turned on by timer. This function is only available in timer “On” mode
and prevents overheating, which may occur if a PDP Display is on for too long time.
English - 20
BN68-01364B-00Eng.indd 20
2007-10-30 ¿ÀÀü 11:01:29
Language / Blue Screen / Melody / Energy Saving /
HDMI Black Level
1
2
3
4
5
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Setup, then press the
ENTER button.
Select the required option by pressing the ▲ or ▼ button, then
press the ENTER button.
When you are satisfied with your setting, press the ENTER
button.
Press the EXIT button to exit.
Setup
Screen Burn Protection
Language
: English
Time
Game Mode
: Off
Blue Screen
: Off
Melody
: Off
PC
Home Theatre PC : Off








 More
Move
Enter
Return
 Language
It is variable depending on the model. When you start using the PDP Display for the first time, you
must select the language which will be used for displaying menus and indications.
 Blue Screen: Off/On
If no signal is being received or the signal is very weak, a blue screen automatically replaces the
noisy picture background. If you wish to continue viewing the poor picture, you must set the Blue
Screen to Off.
 Melody: Off/Low/Medium/High
The PDP Display power on/off melody sound can be adjusted.
 Energy Saving: Off/Low/Medium/High
This feature adjusts the screen brightness depending on the surrounding lighting conditions.
- Off: Switches off the Energy Saving mode.
- Low: Operates in standard mode regardless of the surrounding illumination.
- Medium: Enters medium power saving mode regardless of the surrounding illumination.
- High: Enters maximum power saving mode regardless of the surrounding illumination.
 HDMI Black Level: Normal/Low
Using this function, you can adjust the image quality when the screen burn (appearance of black level,
low contrast, low color, etc.) is encountered by the HDMI input for RGB limited range (16 to 235).
This function is active only when the external input connects to HDMI(RGB signals).
➢
English - 21
BN68-01364B-00Eng.indd 21
2007-10-30 ¿ÀÀü 11:01:30
Setting the Panel Button Lock
This feature allows you to lock the PDP Display panel buttons
so that it cannot be operated via the PDP Display panel. It
can, however, still be operated via the remote control. Only
remote control can release the panel lock setting, so keep the
remote control away from unauthorized users.
1
2
3
4
5
6
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Function, then press the
ENTER button.
Press the ENTER button again to select Safety Lock.
Press the ENTER button again to select Key Lock.
Select Off or On by pressing the ▲ or ▼ button, then press
the ENTER button.
Press the EXIT button to exit.
Function
Safety Lock
Multi Control
Video Wall
Fan
Move
: Off




Enter
Return
Safety Lock
Key Lock
IR Lock
Change PIN
Move
: Off



Enter
Return
Setting the Remote Control Button Lock
This feature allows you to lock the remote control so that it
cannot be operated via the remote control. It can, however,
still be operated via the PDP Display Panel buttons.
1
2
3
4
5
➢
➢
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Function, then press the
ENTER button.
Press the ENTER button again to select Safety Lock.
Press the ▲ or ▼ button to select IR Lock, then press the
ENTER button.
Press the EXIT button to exit.
When IR Lock is set to On, you will not be able to use the
remote control even if the remote control button is pressed.
To cancel the Remote Control Button Lock, press “0000” using
the numeric buttons on the remote control then, IR Lock : Off
is display.
If you press the remote control buttons too quickly, the inputs
may not be recognized. Press the buttons at an interval of
about 2 seconds.
Function
Safety Lock
Multi Control
Video Wall
Fan
Move
: Off




Enter
Return
Safety Lock
Key Lock
IR Lock
Change PIN
Move
: Off



Enter
Return
IR Lock : On
English - 22
BN68-01364B-00Eng.indd 22
2007-10-30 ¿ÀÀü 11:01:30
Setting Up Your Personal ID Number
This feature sets viewing restrictions and prevents
unauthorized access to your PDP Display through the PIN
(Personal Identification Number), which is a 4 digit number.
1
2
3
4
5
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Function, then press the
ENTER button.
Press the ENTER button again to select Safety Lock.
Press the ▲ or ▼ button to select Change PIN, then press
the ENTER button.
Press the number buttons to enter your current 4-digit pin
number.
The default pin number for a new PDP Display set is
“0000”.
Press the numeric buttons to enter your new 4-digit pin
number. Re-enter your new pin number to confirm.
Press the EXIT button to exit.
If you forget the pin number, press the remote control buttons
in the following sequence, which resets the pin to 0-0-0-0:
MUTE, 1, 8, 6.
➢
6
7
➢
Function
Safety Lock
Multi Control
Video Wall
Fan
Move
: Off




Enter
Return
Safety Lock
: Off



Enter
Return
Key Lock
IR Lock
Change PIN
Move
Change PIN
Enter PIN
Enter New PIN
0..9 : Enter PIN
Return
Change PIN
Enter PIN
*
Enter New PIN
0..9 : Enter PIN
Return
English - 23
BN68-01364B-00Eng.indd 23
2007-10-30 ¿ÀÀü 11:01:31
Setting the MDC (Multiple Display Control)
This function enables you to easily control the connected
PDP Displays on the PC by specifying IDs to connected PDP
Displays.
1
2
3
4
5
6
➢
➢
➢
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Function, then press the
ENTER button.
Press the ▲ or ▼ button to select Multi Control, then press
the ENTER button.
Select the required option by pressing the ▲ or ▼ button, then
press the ENTER button.
Available options: ID Setup(00~99), ID Input
When you are satisfied with your setting, press the ENTER
button.
Enter ID input number by using the numeric buttons.
Select the ID setup number by using the numeric buttons.
Press the EXIT button to exit.
To operate the multi control function, PDP1 and PDP2 should
be set in the ID Setup mode. When entering the ID Input
number of PDP1 while the PDP Display is set in the ID Input
mode, only PDP1 is switched to the Menu screen and you can
operate the remote control. At this time, PDP2 doesn’t operate
with the remote control and displays the standby mode of ID
Input.
For further details, refer to the MDC program guide.
You can download the MDC program from the
“www.samsung.com” download center.
Function
Safety Lock
Multi Control
Video Wall
Fan
Move
: Off




Enter
Return
Multi Control
ID Setup
ID Input
: 00
: --


Enter
Return
➢
➢
Move
Multi Control
ID Setup
ID Input
Move
: 00 00
: --
Enter
Return
Multi Control
ID Setup
ID Input
: 00
: -- --
0..9 : Enter ID Input Number
Return
You can select these options by simply pressing the MDC
➢ (Multiple
Display Control) button on the remote control.
English - 24
BN68-01364B-00Eng.indd 24
2007-10-30 ¿ÀÀü 11:01:32
Setting the Multiple Screen
You can get various display effects with many PDPs.
1
2
3
4
5
6
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Function, then press the
ENTER button.
Press the ▲ or ▼ button to select Video Wall, then press the
ENTER button.
Press the ENTER button again.
Press the ▲ or ▼ button to select On, then press the ENTER
button.
Select the required option by pressing the ▲ or ▼ button, then
press the ENTER button.
Available options: Format(Full/Natural), Screen Divider
 Format:
Full: This option displays divided images on multiple PDP
Displays without missing parts as if only the viewable part of
the separate PDP Displays were simply part of a large single
PDP Display.
Natural: This option displays divided images on multiple PDP
Displays as if the separate PDP Displays were simply part of a
large single PDP Display. Therefore there are missing parts on
the edge of the PDP Displays.
Function
Safety Lock
Multi Control
Video Wall
Fan
Move
: Off




Enter
Return
Video Wall
Video Wall
Format
Screen Divider
Move
: Off
: Full
Enter



Return
Video Wall
Video Wall
Format
Screen Divider
 Screen Divider: 2x2, 3x3, 4x4, 5x1, or 1x5
7 Press the EXIT button to exit.
The PIP function and Picture Size do not work during the Video
Wall operation.
: On
: Full Full
Natural
➢
Move
Enter
Return
Screen Divider
2x2
3x3
4x4
5x1
1x5
Move
1
2
3
4
Enter
Return
English - 25
BN68-01364B-00Eng.indd 25
2007-10-30 ¿ÀÀü 11:01:33
Selecting the Fan
Fans inside the PDP Display are used to lower the temperature
of the tops and the front of the PDP Display. To reduce the
noise of the fan, you may stop the fan by setting the Fan to
“Off”. The temperature of the top and the front of the PDP
Display may increase when you watch the PDP Display for
a long period of time while the fan is stopped, but the PDP
Display will operate normally.
1
2
3
4
5
➢
➢
➢
Function
Safety Lock
Multi Control
Video Wall
Fan
Press the MENU button to display the menu.
Move
Press the ▲ or ▼ button to select Function, then press the
ENTER button.
Press the ▲ or ▼ button to select Fan, then press the ENTER button.
Select Off or On by pressing the ▲ or ▼ button, then press the ENTER button.
Press the EXIT button to exit.
If your PDP Display is displayed vertically, the fan automatically works.
The message Check Fan is displayed if there is a fan problem.
Please use the fan when the temperature is over 35 degrees.
: Off




Enter
Return
English - 26
BN68-01364B-00Eng.indd 26
2007-10-30 ¿ÀÀü 11:01:33
Using the Game Mode
When connecting to a game console such as PlayStationTM or
XboxTM, you can enjoy a more realistic gaming experience by
selecting game menu.
1
2
3
4
5
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Setup, then press the
ENTER button.
Press the ▲ or ▼ button to select Game Mode, then press the
ENTER button.
Select Off or On by pressing the ▲ or ▼ button, then press
the ENTER button.
Press the EXIT button to exit.
on Game mode (Caution)
➢ Restrictions
 To disconnect the game console and connect another
➢
➢
Setup
Screen Burn Protection
Language
: English
Time
Game Mode
: Off
Blue Screen
: Off
Melody
: Off
PC
Home Theatre PC : Off








 More
Move
Enter
Return
AV
Game Mode
external device, set Game Mode to Off.
 If you display the PDP Display menu in Game Mode,
the screen shakes slightly.
 The mark ( ) appears on the screen which means that Game Mode is On with the
selected source.
If Game Mode is On :
 Picture Mode is automatically changed to Standard and users cannot change the mode.
 Sound Mode in the Sound menu is deactivated. Adjust the sound using the equalizer.
 The Reset Sound function is activated. Selecting the Reset function after setting the
equalizer resets the equalizer setting to the factory defaults.
If the picture is poor when external device is connected to PDP Display, check if Game Mode is
On. Set Game Mode to Off and connect external devices.
English - 27
BN68-01364B-00Eng.indd 27
2007-10-30 ¿ÀÀü 11:01:33
Viewing the Picture in Picture (PIP)
You can display a sub picture within the main picture of
external A/V devices. In this way you can PDP Display the
video input from any connected devices while monitoring
other video inputs.
1
2
3
4
5
6
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Setup, then press the
ENTER button.
Press the ▲ or ▼ button to select PIP, then press the
ENTER button.
Select the required option by pressing the ▲ or ▼ button,
then press the ENTER button.
Available options: PIP(Off/On), Position
When you are satisfied with your setting, press the ENTER
button.
Press the EXIT button to exit.
 PIP: Off/On
You can activate or deactivate the PIP function.
Main picture
Component
HDMI
PC
DVI
Setup
 More
Energy Saving : Off
HDMI Black Level : Low
PIP
Move
Enter



Return
PIP
PIP
Position
Move
: On
:
Enter


Return
Sub picture
AV
can select these options simply by pressing the PIP
➢ You
button on the remote control.
 Position:
/
/
/
You can select a position of the sub-picture.
English - 28
BN68-01364B-00Eng.indd 28
2007-10-30 ¿ÀÀü 11:01:34
Screen Burn Protection
To reduce the possibility of screen burn, this unit is equipped
with screen burn prevention technology. This technology
enables you to set picture movement up/down (Vertical Line)
and side to side (Horizontal Dot). The Time setting allows
you to program the time between movement of the picture in
minutes.
1
2
3
4
5
6
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Setup, then press the
ENTER button.
Press the ENTER button again to select Screen Burn
Protection.
Select the required option by pressing the ▲ or ▼ button,
then press the ENTER button.
Available options: Pixel Shift, All White, Signal Pattern,
Inverse, Timer, Side Gray
When you are satisfied with your setting, press the
ENTER button.
Press the EXIT button to exit.
 Pixel Shift: Using this function, you can minutely move pixels
on the PDP in horizontal or vertical direction to minimize after
image on the screen.
− Set Pixel Shift to On by pressing the ▲ or ▼ button, then
press the ENTER button.
− Select the required option by pressing the ▲ or ▼ button,
then press the ENTER button.
Available options: Horizontal Dot, Vertical Line, Time
Optimum condition for pixel shift;
➢
PC
Horizontal Dot
Vertical Line
Time (minute)
1
1
2 min
Setup
Screen Burn Protection
Language
: English
Time
Game Mode
: Off
Blue Screen
: Off
Melody
: Off
PC
Home Theatre PC : Off








 More
Move
Enter
Return
Screen Burn Protection
Pixel Shift
All White
Signal Pattern
Inverse
Timer
Side Gray
Move
: Dark
Enter






Return
Pixel Shift
: On
:2
:2
: 2 min
Pixel Shift
Horizontal Dot
Vertical Line
Time
Move
Enter




Return
AV/S-Video/
Component/HDMI
2
2
2 min
➢ The Pixel Shift value may differ depending on the monitor size (inches) and mode.
 All White: This function helps remove after images on the screen by changing the color of pixels to
white. Use this function when there are remaining after images or symbols on the screen especially
when you displayed a still image on the screen for a long time.
 Signal Pattern: This function helps remove after images on the screen by moving all the pixels on
the PDP according to a pattern. Use this function when there are remaining after images or symbols
on the screen especially when you displayed a still image on the screen for a long time.
 Inverse: This function removes after images on the screen when the PDP Display is remained on for
proloned periods by converting RGB input signal into GBR. Compared to All White and Signal Pattern
function, this function can reduce burn in when you watch PDP Display. Using the inverse function
when you watch PDP Display can cause the color reversal on the screen. (ex. The colors in red line
can be shown as the colors in green line on the screen.)
 Side Gray: When you watch PDP Display with the screen ratio of 4:3, the screen is prevented from
any damage by adjusting the white balance on both extreme left and right sides.
Dark: When you set the screen ratio to 4:3, it darkens the left and right sides.
Light: When you set the screen ratio to 4:3, it brightens the left and right sides.
Continued...
English - 29
BN68-01364B-00Eng.indd 29
2007-10-30 ¿ÀÀü 11:01:35
To remove after images on the screen, use either All White, Inverse or Signal Pattern function.
➢ Although
both of the three functions remove after images on the screen, Signal Pattern is more
effective.
after image removal function has to be executed for a long time (approximately 1 hour) to
➢ The
effectively remove after images on the screen. If after image is not improved after the execution of the
function, repeat the function again.
➢ Press any button on the remote control to cancel this feature.
Setting the Screen Burn Protection Timer
You can set the timer for Screen Burn Protection (hours,
minutes). If you start the operation to erase any residual
image, the operation will be performed for the set period of
time and then automatically finish.
1
2
3
4
5
6
7
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Setup, then press the
ENTER button.
Press the ENTER button again to select Screen Burn
Protection.
Press the ▲ or ▼ button to select Timer, then press the
ENTER button.
Press the ENTER button again.
Press the ▲ or ▼ button to select On, then press the ENTER
button.
Select the required option by pressing the ▲ or ▼ button,
then press the ENTER button.
Available options: Timer, Mode, Period, Time
 Mode: All White, Signal Pattern, Inverse
 Period: Hour(1~24)
 Time: Min.(1~30)
8
Press the EXIT button to exit.
Setup
Screen Burn Protection
Language
: English
Time
Game Mode
: Off
Blue Screen
: Off
Melody
: Off
PC
Home Theatre PC : Off








 More
Move
Enter
Return
Screen Burn Protection
Pixel Shift
All White
Signal Pattern
Inverse
Timer
Side Gray
Move
: Dark
Enter






Return
Timer
Timer
Mode
Period
Time
Move
: On
: All White
: 1 Hour
: 30 min.
Enter




Return
English - 30
BN68-01364B-00Eng.indd 30
2007-10-30 ¿ÀÀü 11:01:36
Setting up Your PC Software (Based on Windows XP)
The Windows display-settings for a typical computer are shown below. But the actual screens
on your PC will probably be different, depending upon your particular version of Windows and
your particular video card. But even if your actual screens look different, the same, basic set-up
information will apply in almost all cases. (If not, contact your computer manufacturer or Samsung
Dealer.)
1
2
3
4
5
Right click the mouse on the Windows Desktop, then click on
Properties.
The Display Properties will be displayed.
Click on Settings tab, then set the Display Mode with
reference to the Display Modes Table. You do not need to
change the colors settings.
Click on Advanced. A new settings dialog box will be
displayed.
Click on the Monitor tab, then set the Screen refresh rate
with reference to the Display Modes Table. Set the Vertical
Frequency and Horizontal Frequency individually if you can do
so instead of setting the Screen refresh rate.
Click on OK to close the window, then Click on OK button to
the Display Properties window. Automatic re-booting may commence at this moment.
English - 31
BN68-01364B-00Eng.indd 31
2007-10-30 ¿ÀÀü 11:01:36
Display Modes
Both screen position and size will vary depending on the type of PC monitor and its resolution.
The resolutions in the table are recommended. (All resolutions between the supported limits are
supported)
D-Sub/DVI Input
Resolution
640X350
720X400
640X480
640X480
640X480
640X480
800X600
800X600
800X600
800X600
1024X768
1024X768
1024x768
1024X768
1152X864
1280x960
1280x960
1280X1024
1280X1024
1280X1024
1280X1024
1600X1200
1920x1080P
Horizontal
Frequency (kHz)
31.5
31.5
31.5
37.9
37.5
43.3
37.9
48.1
46.9
53.7
48.4
56.5
60.0
68.7
67.5
60.0
75.1
64.0
74.6
78.0
91.1
75.0
67.5
Vertical
Frequency (Hz)
70
70
60
72
75
85
60
72
75
85
60
70
75
85
75
60
75
60
70
75
85
60
60
PC
DVI
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
X
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
X
O
X
O
X
X
O
X
O
HDMI Input
Resolution
IBM
480p
576p
720p
1080i
1080p




640X480
720x480
720x576
1280x720
1280x720
1920x1080i
1920x1080i
1920x1080P
1920x1080P
1920x1080P
1920x1080P
1920x1080P
Horizontal
Frequency (kHz)
31.5
31.5
31.3
37.5
45.0
28.1
33.7
27.0
28.1
33.8
56.3
67.5
Vertical
Frequency (Hz)
60
60
50
50
60
50
60
24
25
30
50
60
HDMI
O
O
O
O
O
O
O
O
O
O
O
O
The interlace mode is not supported.
The set might operate abnormally if a non-standard video format is selected.
Separate and Composite modes are supported. SOG is not supported.
HDMI is supported for DTV signals only.
English - 32
BN68-01364B-00Eng.indd 32
2007-10-30 ¿ÀÀü 11:01:36
Setting the PC
➢ Preset to the PC mode by pressing the SOURCE button.
1
2
3
4
5
6
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Setup, then press the
ENTER button.
Press the ▲ or ▼ button to select PC, then press the
ENTER button.
Select the required option by pressing the ▲ or ▼ button,
then press the ENTER button.
Available options: Image Lock, Position, Auto Adjustment,
Image Reset, Zoom
When you are satisfied with your setting, press the ENTER
button.
Press the EXIT button to exit.
Setup
Screen Burn Protection
Language
: English
Time
Game Mode
: Off
Blue Screen
: Off
Melody
: Off
PC
Home Theatre PC : Off








 More
Move
Enter
Return
PC
Image Lock
Position
Auto Adjustment
Image Reset
Zoom
 Image Lock: Coarse/Fine
The purpose of picture quality adjustment is to remove or
reduce picture noise.
If the noise is not removed by Fine-tuning alone, then adjust
Move
Enter
the frequency as best as possible (coarse) and Fine-tune
Image Lock
again.
Coarse
After the noise has been reduced, re-adjust the picture so that
Fine
it is aligned on the center of screen.
1 Press the ▲ or ▼ button to select Coarse or Fine, then
press the ENTER button.
2 Press the ◄ or ► button to adjust the screen quality,
vertical stripes may appear or the picture may be blurry.
Press the ENTER button.
Move
Enter
 Position
Adjust the PC’s screen positioning if it does not fit the PDP
Position
Display screen.
1 Adjust the position by pressing the ▲/▼/◄/► button.
2 Press the ENTER button.
 Auto Adjustment
Auto adjustment allows the PC screen of set to self-adjust to
the incoming PC video signal.
The values of fine, coarse and position are adjusted
automatically.
Move
Enter
 Image Reset
You can replace all image settings with the factory default
Auto Adjustment in Progress
values.
Please wait.
 Zoom: Zoom/Position/Reset
- Zoom: 0 - 1 - 2 - 3 - 4 - 5 - 6
Option 0 represents a normal screen.
Image Reset is completed.
The greater the number, the more magnified the
Return
screen.
You can select the position and reset functions by
selecting options 1 through 6. (If you select option 0,
the position and reset functions are not selected.)
If you have selected the Zoom function as between 1~6,
you will not be able to select the Auto Adjustment function.
- Position: You can adjust the position.
- Reset: The previously adjusted settings will be reset to the factory defaults.





Return
50
13
Return
Return
English - 33
BN68-01364B-00Eng.indd 33
2007-10-30 ¿ÀÀü 11:01:37
Setting the Home Theatre PC
➢ Preset to the PC mode by pressing the SOURCE button.
Setup
You can view higher quality pictures by configuring the
screen settings in PC Mode.
If you set the Home Theatre PC function to On, you can
configure the Detailed Settings (when Picture Mode is set to
Standard or Movie) as in PC Mode.








 More
1
2
3
4
5
Screen Burn Protection
Language
: English
Time
Game Mode
: Off
Blue Screen
: Off
Melody
: Off
PC
Home Theatre PC : Off
➢
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Setup, then press the
Move
ENTER button.
Press the ▲ or ▼ button to select Home Theatre PC, then
press the ENTER button.
Select Off or On by pressing the ▲ or ▼ button, then press the ENTER button.
Press the EXIT button to exit.
This function is available only in PC mode.
Enter
Return
Wall Mount Kit Specifications (VESA)
Install your wall mount on a solid wall perpendicular to the floor.
When attaching to other building materials, please contact your nearest dealer.
If installed on a ceiling or slanted wall, it may fall and result in severe personal injury.
Product Family
LCD-TV
PDP-TV/MONITOR
inch
VESA Spec. (A * B)
Standard Screw
23 ~ 26
200 * 100
M4
32 ~ 40
200 * 200
M6
46 ~ 52
600 * 400
57
700 * 400
(No VESA)
57 ~ 70
800 * 400
80 ~
1400 * 800
42 ~ 58
600 * 400
70
800 * 400
63
No VESA
80 ~
1400 * 800
Quantity
4
M8
4
M8
6
4
Continued...
English - 34
BN68-01364B-00Eng.indd 34
2007-10-30 ¿ÀÀü 11:01:38
provided the standard dimensions for wall mount kits as shown in the table.
➢ We
When purchasing our wall mount kit, a detailed installation manual and all parts necessary for
➢ assembly
are provided.
Do not use screws longer than the standard dimension, as they may cause damage to the inside of
➢ the
PDP Display set.
wall mounts that do not comply with the VESA standard screw specifications, the length of the
➢ For
screws may differ depending on their specifications.
Do not use screws that do not comply with the VESA standard screw specifications.
➢ Do
not use fasten the screws too strongly, this may damage the product or cause the product to fall,
leading to personal injury. Samsung is not liable for these kinds of accidents.
Samsung is not liable for product damage or personal injury when a non-VESA or non-specified wall
➢ mount
is used or the consumer fails to follow the product installation instructions.
Our 57” and 63” models do not comply with VESA Specifications. Therefore, you should use our
➢ dedicated
wall mount kit for this model.
➢ Do not exceed 15 degrees tilt when mounting this PDP Display.
Do not install your Wall Mount Kit while your PDP Display is turned on.
It may result in personal injury due to electric shock.
Using the Stand-Base
➢
 Two or more people should carry the PDP. Never lay the
PDP on the floor because of possible damage to the screen.
Always keep the PDP upright.
English - 35
BN68-01364B-00Eng.indd 35
2007-10-30 ¿ÀÀü 11:01:39
Troubleshooting
Before contacting the Samsung after-sales service, perform the following simple checks.
If you cannot solve the problem using the instructions below, note the model and serial number of
the PDP Display and contact your local dealer.
No sound or picture
 Check that the mains lead has been connected to a wall socket.
 Check that you have pressed the (Power) button (On/Off) on the front panel or press the ON button
on the remote control.
 Check the picture contrast and brightness settings.
 Check the volume.
 Check if Internal Mute is set to On.
Normal picture but no sound
 Check the volume.
 Check whether the volume MUTE button on the remote control has been pressed.
No picture or black and white picture
 Adjust the Color settings.
Sound and picture interference
 Try to identify the electrical appliance that is affecting the PDP Display, then move it further away.
 Plug the PDP Display into a different main socket.
Remote control malfunctions
 Replace the remote control batteries.
 Clean the upper edge of the remote control (transmission window).
 Check that the “+” and “–” ends of the batteries are inserted correctly.
 Check that the batteries are drained.
Screen is black and power indicator light blinks steadily
 On your computer check; Power, Signal Cable.
 The PDP Display is using its power management system.
 Move the computer’s mouse or press any key on the keyboard.
 On your equipment check (STB, DVD, etc) ; Power, Signal Cable.
 Press the Source button on the panel or remote control.
 Turn the PDP Display off and on.
The damaged picture appears in the corner of the screen.
 If Just Scan is selected in some external devices, the damaged picture may appear in the corner of
the screen. This symptom is caused by external devices, not PDP Display.
English - 36
BN68-01364B-00Eng.indd 36
2007-10-30 ¿ÀÀü 11:01:39
Specifications
Model Name
Screen Size (Diagonal)
PPM50M7F
PPM63M7F
50 inch
63 inch
PC Resolution
1920 x 1080 @ 60 Hz
Sound (Output)
10 W + 10 W
Dimension (WxHxD)
Body
With stand
Weight
Body
With stand
Environmental Considerations
Operating Temperature
Operating Humidity
Storage Temperature
Storage Humidity
➢
1204.6 x 724.1 x 97.1 mm
1204.6 x 772.5 x 362.0 mm
1502.7 x 893.1 x 99.0 mm
1502.7 x 942.3 x 341.1 mm
43.5 kg
44.5 kg
63.9 kg
68.9 kg
10 °C to 40 °C (50 °F to 104 °F)
10% to 80%, non-condensing
-20 °C to 45 °C (-4 °F to 113 °F)
5% to 95%, non-condensing
 This device is a Class B digital apparatus.
 Design and specifications are subject to change without prior notice.
 For the power supply and Power Consumption, refer to the label attached to the product.
English - 37
BN68-01364B-02Eng.indd 37
2007-12-11 ¿ÀÀü 11:15:24
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with
separate collection systems)
This marking shown on the product or its literature, indicates that it
should not be disposed with other household wastes at the end of its
working life.
To prevent possible harm to the environment or human health from
uncontrolled waste disposal, please separate this from other types of
wastes and recycle it responsibly to promote the sustainable reuse of
material resources.
Household users should contact either the retailer where they
purchased this product, or their local government office, for details
of where and how they can take this item for environmentally safe
recycling.
Business users should contact their supplier and check the terms and
conditions of the purchase contract. This product should not be mixed
with other commercial wastes for disposal.
BN68-01364B-00Eng.indd 38
2007-10-30 ¿ÀÀü 11:01:40
Contact SAMSUNG WORLD-WIDE
If you have any questions or comments relating to Samsung products, please contact the
SAMSUNG customer care centre.
Comment contacter Samsung dans le monde
Si vous avez des suggestions ou des questions concernant les produits Samsung, veuillez
contacter le Service Consommateurs Samsung.
Kontakt zu Samsung
Falls Sie Fragen oder Anregungen zu Samsung-Produkten haben, wenden Sie sich bitte an den
Samsung-Kundendienst.
Contatta SAMSUNG WORLD-WIDE
Se avete commenti o domande sui prodotti Samsung, contattate il Servizio Clienti Samsung.
Contacte SAMSUNG GLOBAL
Se tem algumas dúvidas ou comentários sobre os produtos Samsung, contacte por favor a nossa
linha de apoio a clientes Samsung.
Связывайтесь с SAMSUNG по всему миру
Если у вас есть предложения или вопросы по продуктам Samsung, связывайтесь с
информационным центром Samsung.
Kontaktirajte SAMSUNG WORLD WIDE (Samsung diljem sveta)
Ako imate pitanja ili komentara u vezi proizvoda kompanije Samsung, kontaktirajte službu za
korisnike kompanije SAMSUNG.
Contacte con SAMSUNG WORLD-WIDE
Si tiene alguna pregunta o comentario referente a nuestros productos, por favor contacte con
nuestro Servicio de Atención al Cliente.
Kontakta Samsung
Om du har några frågor eller synpunkter om Samsungs produkter, är du välkommen att kontakta
Samsung Support.
BN68-01364B-00Eng.indd 39
2007-10-30 ¿ÀÀü 11:01:40
Country
AUSTRIA
BELGIUM
Web Site
Customer Care Centre 
0800-SAMSUNG(726-7864)
www.samsung.com/at
0032 (0)2 201 24 18
www.samsung.com/be
844 000 844
www.samsung.com/cz
CZECH REPUBLIC
Distributor pro Českou republiku:
Samsung Zrt., česka organizační složka Vyskočilova 4, 14000 Praha 4
DENMARK
70 70 19 70
www.samsung.com/dk
FINLAND
030-6227 515
www.samsung.com/fi
3260 SAMSUNG(726-7864)
FRANCE
www.samsung.com/fr
08 25 08 65 65 (€ 0,15/Min)
GERMANY
01805 - 121213 (€ 0,14/Min)
www.samsung.de
06-80-SAMSUNG(726-7864)
www.samsung.com/hu
HUNGARY
800-SAMSUNG(726-7864)
www.samsung.com/it
ITALIA
LUXEMBURG
0035 (0)2 261 03 710
www.samsung.com/be
NETHERLANDS
0900 20 200 88 (€ 0,10/Min)
www.samsung.com/nl
NORWAY
815-56 480
www.samsung.com/no
0 801 801 881
POLAND
www.samsung.com/pl
022-607-93-33
80 8 200 128
www.samsung.com/pt
PORTUGAL
REPUBLIC OF IRELAND 0818 717 100
www.samsung.com/ie
0800-SAMSUNG(726-7864)
www.samsung.com/sk
SLOVAKIA
SPAIN
902 10 11 30
www.samsung.com/es
SWEDEN
0771-400 200
www.samsung.com/se
SWITZERLAND
0800-SAMSUNG(726-7864)
www.samsung.com/ch
U.K
0870-SAMSUNG(726-7864)
www.samsung.com/uk
ESTONIA
800-7267
www.samsung.ee
8-10-800-500-55-500
www.samsung.kz
KAZAHSTAN
00-800-500-55-500
KYRGYZSTAN
LATVIA
800-7267
www.samsung.com/lv
LITHUANIA
8-800-77777
www.samsung.lt
RUSSIA
8-800-555-55-55
www.samsung.ru
UKRAINE
8-800-502-0000
www.samsung.ua
8-800-120-0-400
www.samsung.uz
UZBEKISTAN
BN68-01364B-00Eng.indd 40
2007-10-30 ¿ÀÀü 11:01:40
BN68-01364B-02
BN68-01364B-02Eng.indd 42
2007-12-11 ¿ÀÀü 11:16:39
Download PDF