Samsung | SP-42W5HF | Samsung SP-42W5HF Benutzerhandbuch

COLOUR
TELEVISION
SP42W4/42W5
SP43T6/43T7/43T8/43W6
SP47Q7/47W1/47W3
SP48T6
SP52Q7
SP54T6/54T8
SP55W3
SP62T6/62T8
SP65W3
Owner’s Instructions
Before operating the unit,
please read this manual thoroughly,
and retain it for future reference.
ON-SCREEN MENUS
PICTURE IN PICTURE
TELETEXT
Important Warranty Information Regarding Television
Format Viewing
ENG
Standard screen format televisions (4:3, the aspect ratio of the screen width to height) are
primarily designed to view standard format full-motion video. The images displayed on them
should primarily be in the standard 4:3 ratio format and constantly moving. Displaying stationary
graphics and images on screen, such as the dark top and bottom letterbox bars (wide screen
pictures), should be limited to no more than 15% of the total television viewing per week.
Wide screen format televisions (16:9, the aspect ratio of the screen width to height) are
primarily designed to view wide screen format full-motion video. The images displayed on them
should primarily be in the wide screen 16:9 ratio format, or expanded to fill the screen if your
model offers this feature, and constantly moving. Displaying stationary graphics and images on
screen, such as the dark side-bars on non-expanded standard format television video and
programming, should be limited to no more than 15% of the total television viewing per week.
Additionally, viewing other stationary images and text such as stock market reports, video
game displays, station logos, web sites or computer graphics and patterns, should be limited as
described above for all televisions. Displaying any stationary images that exceed the above
guidelines can cause uneven aging of picture tubes (CRTs) that leave subtle, but permanent
burned-in ghost images in the television picture. To avoid this, vary the programming and
images, and primarily display full screen moving images, not stationary patterns or dark bars.
On television models that offer picture sizing features, use these controls to view the different
formats as a full screen picture.
B
e careful in the selection and duration of television formats used for viewing. Uneven CRT
aging as a result of format selection and use, as well as other burned-in images, is not covered by
your Samsung limited warranty.
2
Safety Instructions
ENG
◆ Do not expose the television to extreme temperature conditions or to extreme humidity conditions.
◆ Do not expose the television to direct sunlight and other sources of heat.
◆ Do not expose the television to any liquids.
◆ Never put objects of any kind into the television, and do not place a water-containing vessel on the
television.
◆ During a storm conditions (especially when there is lightning) unplug the television from the mains
socket and aerial.
◆ Do not step on or twist the power cord.
◆ Do not overload wall outlets or extension cords as this can result in a risk of fire or electric shock.
◆ Please use a soft and dry cloth (not containing volatile matter) when you clean the TV.
◆ If the television is broken, do not try to repair it yourself. Contact qualified service personnel.
◆ If the remote control is not used for a long period of time, remove the batteries and store it in a
cool, dry place.
◆ Do not drop the remote control.
☛
Displaying any stationary images that exceed the long time, it can cause uneven aging of
picture tubes that leave subtle, but permanent burned-in ghost images in the television
picture. To avoid this, vary the programming and images, and primarily display full
screen moving images, not stationary patterns or dark bars.
This device is not for use in industrial environments.
Caution
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO PREVENT ELECTRICAL SHOCK,
DO NOT REMOVE REAR COVER, NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
WARNING: TO PREVENT DAMAGE WHICH MAY RESULT
IN FIRE OR SHOCK HAZARD. DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
The lightning flash and arrow head
within the triangle is a warning sign
alerting you of “dangerous voltage”
inside the product.
The exclamation point within the
triangle is a warning sign alerting
you of important instructions
accompanying the product.
☛
The main voltage is indicated on the
rear of the TV set and the frequency is
50 or 60Hz.
3
ENG
Contents (continued)
◆ FOREWORD
■
■
■
Important Warranty Information Regarding Television Format Viewing ........
Safety Instructions .........................................................................................
Caution ..........................................................................................................
2
3
3
◆ CONNECTING AND PREPARING YOUR TELEVISION
■
■
■
■
■
■
■
■
■
■
■
■
■
Control Panels ............................................................................................... 6~7
Connection Panels ........................................................................................
8
Using a Display Deck ....................................................................................
9
Infrared Remote Control ................................................................................
10
Inserting the Batteries in the Remote Control................................................
11
Connecting to an Aerial or Cable Television Network ...................................
11
Switching Your Television On and Off...........................................................
12
Placing Your Television in Standby Mode .....................................................
12
Becoming Familiar with the Remote Control .................................................
13
Plug and Play Feature ................................................................................... 14~15
Viewing the Demonstration............................................................................
16
Choosing Your Language..............................................................................
16
Adjusting Convergence .................................................................................
17
◆ SETTING THE CHANNELS
■
■
■
■
■
■
Storing Channels Automatically.....................................................................
18
Sorting the Stored Channels .........................................................................
19
Storing Channels Manually............................................................................ 20~21
Assigning Names to Channels ......................................................................
22
Activating the Child Lock and Skipping Unwanted Channels ........................
23
Selecting a Channel by Informations.............................................................
24
◆ USING YOUR TELEVISION (continued)
■
■
■
■
■
■
■
■
■
■
■
Changing the Picture Standard .....................................................................
Adjusting the Picture Settings........................................................................
Freezing the Current Picture .........................................................................
Extra Picture Settings ....................................................................................
- Scan Mode
- Digital NR
- Blue screen
- LNA (Low Noise Amplifier)
Selecting the Picture Size (depending on the model)....................................
Changing the Sound Standard ......................................................................
Adjusting the Sound Settings ........................................................................
Adjusting the Volume Automatically ..............................................................
Setting the Melody Sound .............................................................................
Setting the Dolby Digital ................................................................................
Adjusting Your Dolby Preferences.................................................................
24
25
25
26
27
28
28
29
29
30
31
The page numbers are changed.
4
ENG
Contents
◆ USING YOUR TELEVISION
■
■
■
■
■
■
Setting the External Sound............................................................................
32
Selecting the Sound Mode (depending on the model) ..................................
33
Setting the Sleep Timer .................................................................................
34
Setting and Displaying the Current Time.......................................................
34
Switching the Television On and Off Automatically .......................................
35
Viewing the Picture In Picture (PIP) .............................................................. 36~37
◆ USING THE TELETEXT FEATURE
■
■
■
■
Teletext Feature ............................................................................................
Displaying the Teletext Information ...............................................................
Selecting Display Options..............................................................................
Selecting a Teletext Page..............................................................................
38
39
40
41
◆ ADDITIONAL INFORMATION ON CONNECTIONS
■
■
■
■
■
■
■
Connecting to the External Input/Outputs......................................................
Connecting to the Audio Output ....................................................................
Connecting to the RCA Input.........................................................................
Connecting to the S-Video Input....................................................................
Connecting Additional Speakers ...................................................................
Viewing Pictures From External Sources ......................................................
Redirecting an Input to the External Output ..................................................
42
43
43
44
44
45
46
◆ RECOMMENDATIONS FOR USE
■
■
■
■
Programming the Remote Control for Other Components ............................
- TV Remote Control Codes .........................................................................
- VCR Remote Control Codes ......................................................................
- Cable Box (CATV) Remote Control Codes ................................................
- DVD Remote Control Codes ......................................................................
SCART Connector Wiring (EXT1, EXT2 or EXT3) ........................................
Troubleshooting: Before Contacting Service Personnel................................
Wiring the Mains Power Supply Plug (UK Only)............................................
47
48
49
50
50
51
52
53
The page numbers are changed.
Symbols
Press
☛
Important
➢
Note
5
Control Panels (depending on the model)
➢
ENG
The actual configuration on your TV may be different, depending on
your model.
( a ) Input Source Selection
( e ) Channel Selection
( b ) Temporary Sound Switch Off
(f)
( c ) Menu Display
( g ) Standby & Timer Indicator
( d ) Volume Adjustment
( h ) Power On/Off
6
Remote Control Sensor
Control Panels (depending on the model)
➢
The actual configuration on your TV may be different, depending on
your model.
( a ) Input Source Selection
( e ) Channel Selection
( b ) Temporary Sound Switch Off
(f)
( c ) Menu Display
( g ) Standby & Timer Indicator
( d ) Volume Adjustment
( h ) Power On/Off
ENG
Remote Control Sensor
7
Connection Panels (depending on the model)
➢
ENG
The actual configuration on your TV may be different, depending on
your model.
Front of the TV
Side of the TV
Video Input
Auto Convergence
Video Input
Audio Input
Auto Convergence
Audio Input
S-Video Input
Rear of the TV
Center Speaker Connectors (Option)
Rear Speaker Connectors
75Ω Coaxial Connector for Aerial or Cable Network
SCART Audio/Video Input/Output
Audio Output
8
S-Video Input
Using a Display Deck (depending on the model)
ENG
You can display a VCR or DVD Player, etc. by using the display
deck.
SP47W3/55W3/65W3
SP47W3/55W3/65W3
1
Press the symbol “
2
Hold the center of the door and lift it up in the direction of arrow till
a ‘ttok’ sound sounds.
3
After placing a component you have in the display deck, hold the
center of the door and pull it down.
4
Shut the door by pressing the symbol “
” at the center of the display deck.
”.
SP54T8/62T8
SP54T8/62T8
1
Hold the center of the door and lift it up in the direction of arrow.
2
After placing a component you have in the display deck, hold the
center of the door and pull it down.
➣
You should display only the component that is within
126mm high. When displaying a component in the
display deck, please space it out 30mm from the front,
20mm from either end.
9
Infrared Remote Control
ENG
Power
TELEVISION STANDBY
TV
VCR
Cable
DVD
SET
MAKE THE REMOTE CONTROL
WORKS FOR TV, VCR, CABLE,
DVD PLAYER
REMOTE CONTROL SETUP
NUMERIC BUTTONS FOR
DIRECT ACCESS
(CHANNEL/TELETEXT PAGE)
ONE, TWO, OR THREE-DIGIT
CHANNEL SELECTION
(DEPENDING ON THE MODEL)/
TELETEXT STORE (OPTION)
TV
Surround
S.STD
P.STD
S.Mode
TUNER/CABLE NETWORK SELECTION
FASTEXT TOPIC SELECTION
SOUND MODE SELECTION
SURROUND ON/OFF DIRECTLY
PICTURE EFFECT SELECTION
SOUND EFFECT SELECTION
NEXT CHANNEL/
TELETEXT NEXT PAGE
VOLUME INCREASE
Mute
Still
VOL
TEMPORARY SOUND SWITCH OFF
P
PICTURE FREEZE
PREVIOUS CHANNEL/
TELETEXT PREVIOUS PAGE
VOLUME DECREASE
Menu
Video
EXTERNAL INPUT SELECTION/
TELETEXT MODE (LIST/FLOF)
SELECTION (OPTION)
MENU DISPLAY/
PROGRAMME SELECTION BY NAME
CONTROL THE CURSOR IN THE
ON-SCREEN MENU
CHANGE CONFIRMATION
ON-SCREEN MENUS DISPLAY/
TELETEXT REVEAL
Display
P.Size
AINFORMATION DISPLAY
TELETEXT DISPLAY/
MIX BOTH TELETEXT INFORMATION
AND THE NORMAL BROADCAST
VCR/DVD FUNCTIONS;
- STOP
- REWIND
- PLAY/PAUSE
- FAST FORWARD
TELETEXT SUB-PAGE
PICTURE SIZE/TELETEXT SIZE
AUTOMATIC SWITCH-OFF
Text/Mix
Info.
Sleep Perfect Focus
PIP
ON
Scan
Swap
Locate
AUTOMATIC ADJUST THE
CONVERGENCE
PIP FUNCTIONS;
- PIP ON/OFF
- CHANNEL SCAN
- INTERCHANGE THE MAIN AND
SUB PICTURE
- LOCATION SELECTION
TELETEXT PAGE HOLD
TELETEXT CANCEL
➢
10
The performance of the
remote control may be
affected by bright light.
Inserting the Batteries in the Remote Control
ENG
You must insert or replace the batteries in the remote control when
you:
◆ Purchase the television
◆ Find that the remote control is no longer operating
correctly
1
Remove the cover on the rear of the remote control by pressing
the symbol downwards and then pulling firmly to remove it.
2
Insert two R03, UM4, “AA” 1.5V or equivalent batteries taking care
to respect the polarities:
◆ + on the battery against + on the remote control
◆ - on the battery against - on the remote control
3
Replace the cover by aligning it with the base of the remote
control and pressing it back into place.
Connecting to an Aerial or Cable Television Network
To view television channels correctly, a signal must be received by
the set from one of the following sources:
◆ An outdoor aerial
◆ A cable television network
◆ A satellite network
1
In the first three cases, connect the aerial or network input cable to
the 75Ω coaxial socket on the rear of the television.
2
If you are using an indoor aerial, you may need to turn it when
tuning your television until you obtain a picture that is both sharp
and clear.
For further details, refer to:
◆ “Storing Channels Automatically” on page 18
◆ “Storing Channels Manually” on page 20
Rear of the TV
or
Cable Television
Network
11
Switching Your Television On and Off
ENG
The mains lead is attached to the rear of your television.
☛
If you have purchased this television in the United
Kingdom, refer to page 53 for further instructions on
plug wiring.
Power
TV
VCR
Cable
DVD
SET
1
Plug the mains lead into an appropriate socket.
2
Press the “ I ” button (On/Off) on the front of the television.
main voltage is indicated on the rear of the television
➣ The
and the frequency is 50 or 60Hz.
Result:
3
The Standby indicator on the front of the television
lights up.
Press the Power ( ) button on the remote control to switch the
television on.
Result:
The programme that you were watching last is reselected automatically.
you have not yet stored any channels, No clear picture
➣ Ifappears.
Refer to “Storing Channels Automatically” on page
16 or “Storing Channels Manually” on page 18.
4
To switch your television off, press the “ I ” button (On/Off) again.
Placing Your Television in Standby Mode
Your television can be placed in Standby mode, in order to reduce
the power consumption.
The Standby mode can be useful when you wish to interrupt
viewing temporarily (during a meal, for example).
Power
TV
VCR
Cable
DVD
SET
1
Press the Power ( ) button on the remote control.
Result:
2
To switch the television back on, simply press the Power ( )
button again.
☛
12
The screen is turned off and the Standby indicator on
the front of the television lights up in red.
Do not leave your television in Standby mode for long
periods of time (when you are away on holiday, for
example). Turn your television off by pressing the “ I “
button (On/Off) on the front of the television. It is best to
unplug the set from the mains and aerial.
Becoming Familiar with the Remote Control
ENG
The remote control is used mainly to:
◆ Change channels and adjust the volume
◆ Set up the television using the on-screen menu system
Power
The following table presents the most frequently used buttons and
their functions.
Button
Viewing Function
TV
VCR
Cable
DVD
SET
Menu Function
Used to display the next stored channel.
P
Used to display the previous stored channel.
to
-/--/---
Used to display the corresponding channels.
Used to select a channel numbered ten or over.
Press this button, and enter the two or three-digit channel
number (depending on the model).
TV
Surround
P.STD
S.STD
Mute
+
VOL
-
Used to increase the volume.
Mute
Used to switch the sound off temporarily.
To turn the sound back on, press this button again, or
VOL- or VOL+ button.
Menu
Used to display the
on-screen menu system.
▲
➛❿
▼
TV
Still
VOL
Used to decrease the volume.
S.Mode
P
Menu
Video
➣
-
Used to return to the previous
menu or normal viewing.
Used to...
◆ Display a submenu
containing selections for
the current menu option.
◆ Increase/reduce a menu
option value.
-
Used to confirm your choice.
Used to switch the
television on when it is
in Standby mode.
Used to exit from the menu
system and return to normal
viewing directly.
Display
P.Size
Text/Mix
Info.
Sleep Perfect Focus
PIP
ON
Scan
Swap
13
Locate
Plug and Play Feature
ENG
When the television is initially powered on, several basic customer
settings proceed automatically and subsequently. The following
settings are available.
1
English
If the television is in Standby mode, press the Power ( ) button
on the remote control.
Result:
ЬА
Hrvatski
Čeština
Netherland
Français
2
Select the appropriate language by pressing the ▼ or ▲ button.
Press the Menu button to enter the language.
Result:
➣
3
The message Antenna input check is displayed.
If any language is not selected on the Language menu, the
Language menu will disappear about 30 seconds later.
Make sure that the antenna is connected to the TV.
Press the ➛ or ❿button.
Result:
The ATM menu is displayed.
4
Select your country by pressing the ➛ or ❿ button.
5
To search the channels, press the
Result:
➢
6
7
button.
The channels are stored in an order which reflects
their positions in the frequency range. Finally, the
search will end automatically. When the channels
have been stored, the Time menu is displayed with
Clock is selected.
To stop the search before it has finished, press the Menu
button.
Press the ➛ or ❿button to move to the hour or minute.
Set the hour or minute by pressing the ▼ or ▲ button.
➣
Refer to “Setting and Displaying the Current Time” on page
34.
When you have finished, press the Menu button.
Result:
14
The message Plug & Play is displayed. It flickers for
a little while and then Language menu is automatically
displayed.
The message Enjoy viewing your new TV is
displayed, and then the channel which has been
stored will be activated.
Plug and Play Feature
ENG
If you want to reset this feature...
1
Press the Menu button.
Result:
2
The main menu is displayed.
Press the ▼ or ▲ button to select Function.
Result:
The options available in the Function group are
displayed.
3
Press the
4
Press the ▼ or ▲ button to select Plug & Play. Press the
button.
Result:
button.
This feature starts with the message Plug & Play is
displayed.
15
Viewing the Demonstration
ENG
Menu
Video
To become familiar with the various menus provided by your
television, you can view the inbuilt demonstration.
1
Press the Menu button.
Result:
2
Display
The main menu is displayed.
Press the ▼ or ▲ button to select Function.
P.Size
Result:
The options available in the Function group are
displayed.
3
Press the
4
Press the ▼ or ▲ button to select Demonstration. Press the
button.
Result:
➣
button.
Each of the menu options is displayed in turn.
When you wish to exit from the demonstration, press the TV
button on the remote control.
Choosing Your Language
When you start using your television for the first time, you must
select the language which will be used for displaying menus and
indications.
1
Press the Menu button.
Result:
2
Press the ▼ or ▲ button to select Function .
Result:
3
English
Hrvatski
Čeština
Press the
Result:
ЬА
4
Press the
Result:
Netherland
The main menu is displayed.
The options available in the Function group are
displayed.
button.
The Language is selected.
button again.
The languages available are listed.
Français
5
16
Press the ▼ or ▲ button to select the appropriate language.
Adjusting Convergence
ENG
If the color appears spread out or “smeared” on the screen, the
convergence probably needs alignment. Be sure to use the remote
control for the convergence adjustments. (The Convergence
Adjustment can not be made by using the control buttons on the
front panel.)
1
Press the MENU button.
Result:
2
The main menu is displayed.
Press the ▼ or ▲ button to select Function.
Result:
The options available in the Function group are
displayed.
3
Press the
4
Press the ▼ or ▲ button to select Convergence. Press the
button.
Result:
5
Press the
Result:
6
button.
The options available in the Convergence group are
displayed with Red is selected.
button again.
A crosshair pattern is appeared.
Adjust convergence by using your remote control.
◆ Use the ▼/▲/➛/❿ buttons to all directions for select the
position.
◆ Press the “0” button to select red or blue convergence.
◆ To move the line so that it is superimposed on the horizontal
or vertical center-line, use the volume up/down (VOL +/-) and
channel up/down (P
/
) buttons (i.e., make a signal
horizontal or vertical line that is as white as possible).
◆ Press the Menu button to exit.
You can adjust convergence automatically for the optimum in the
factory.
7
Select Perfect Focus in the Function group, then press the
button.
Result:
➣
➣
Perform Perfect Focus in the following sequence:
green ➞ red ➞ blue.
After the cursor flickers for one second, the perfect
focus feature ends.
You can also adjust simply by pressing the Perfect Focus
button.
When the size of the sub picture is selected to the “12 PIP”
or “3 PIP” mode, the Perfect Focus feature does not work.
Text/Mix
Info.
Sleep Perfect Focus
PIP
ON
Scan
Swap
17
Locate
Storing Channels Automatically
ENG
You can scan for the frequency ranges available to you (and
availability depends on your country). Automatically allocated
programme numbers may not correspond to actual or desired
programme numbers. However you can sort numbers manually and
clear any channels you do not wish to watch.
1
Press the Menu button.
The main menu is displayed.
Result:
2
Press the ▼ or ▲ button to select Channel.
The options available in the Channel group are
Result:
displayed.
3
Press the
button.
The Country is selected.
Result:
4
Press the
button again. Select your country by pressing the
▼ or ▲ button.
The countries are displayed in the following order:
Belgium - Germany - Spain - France - Italia - Netherlands
- Swizerland - Sweden - United Kingdom - East europe Others.
➢ If you have selected the Others option but do not wish to
scan the PAL frequency range, store the channels manually
(see page 20).
5
Press the Menu button.
The options available in the Channel group are
Result:
displayed again.
6
Press the ▼ or ▲ button to select ATM. Press the
7
Press the
button again to start the search.
The channels are stored in an order which reflects
Result:
their positions in the frequency range. Finally, the
search will end automatically.
➢
8
18
button.
To stop the search before it has finished, press the Menu
button.
When the channels have been stored, you can:
◆ Sort them in the order required (refer to page 19)
◆ Assign a name to the stored channels (refer to page 22)
◆ Clear a channel (refer to page 23)
◆ Fine tune channel reception if necessary (refer to page 21)
◆ Activate the Digital Noise Reduction feature (refer to page 26)
Sorting the Stored Channels
ENG
This operation allows you to change the programme numbers of
stored channels. This operation may be necessary after using auto
store. You can delete the channels you do not want to keep.
1
Press the Menu button.
Result:
2
Press the ▼ or ▲ button to select Channel.
Result:
3
4
The main menu is displayed.
Press the
The options available in the Channel group are
displayed.
button.
Press the ▼ or ▲ button to select Sort. Press the
Result:
button.
The Sort menu is displayed.
5
Select the channel that you wish to move by pressing the ▼ or ▲
button. Press the ❿ button.
6
Select the number of the programme to which the channel is to be
moved by pressing the ▼ or ▲ button. Press the ➛ button
The channel is moved to its new position and all other
Result:
channels are shifted accordingly.
7
Repeat Steps 5 to 6 until you have moved all the channels to the
required programme numbers.
19
Storing Channels Manually
ENG
You can store up to 100 television channels, including those
received via cable networks.
When storing channels manually, you can choose:
◆ Whether or not to store each of the channels found
◆ The programme number of each stored channel which
you wish to identify
1
Press the MENU button.
Result:
2
Press the ▼ or ▲ button to select Channel.
Result:
The options available in the Channel group are
displayed.
3
Press the
4
Press the ▼ or ▲ button to select Manual Store. Press the
button.
Result:
5
6
button.
The options available in the Manual Store group are
displayed with Color system is selected.
Indicate the broadcasting standard required by pressing the ➛ or
❿ button repeatedly.
Result:
The colour standards are displayed in the following
order:
AUTO - PAL - SECAM - NTSC4.43.
Press the ▼ or ▲ button to select Sound system. Select the
sound standard required by pressing the ➛ or ❿ button
repeatedly.
Result:
20
The main menu is displayed.
The sound standards are displayed in the following
order:
BG - DK - I - L.
Storing Channels Manually (continued)
ENG
7
If you know the number of the channel to be stored, see the
following steps.
◆ Press the ▼ or ▲ button to select Channel.
◆ Press the ❿ button.
◆ Press the ▼ or ▲ button to select C (Air channel) or S (Cable
channel).
◆ Press the ❿button.
◆ Press the ▼ or ▲ button to select indicate the required
number.
➣
8
If you do not know the channel numbers, select Search by
pressing the ▼ or ▲ button. Press the ➛ or ❿ button to start the
search.
Result:
9
If no sound or abnormal sound, re-select the sound
standard required.
The tuner scans the frequency range until the first
channel or the channel that you selected is received
on your screen.
If reception is weak, you can fine tune a channel manually. Press
the ▼ or ▲ button to select Fine tune. Press the ➛ or ❿ button
until the picture and sound are both clear and sharp.
➢
◆ You can ignore any changes made and return to the
previous setting by pressing the Green (S.STD) button.
◆ If you are unable to fine tune a channel, check that the
Color System and Sound System settings are correct.
10
To assign a programme number to a channel, select Prog.No by
pressing the ▼ or ▲ button. Press the ➛ or ❿ button to find the
correct number.
11
To store the channel and associated programme number, press
the
button.
12
Repeat Steps 7 to 11 for each channel to be stored.
☛
Channel mode
◆ P (Programme mode): When completing tuning, the
broadcasting stations in your area have been assigned to
position numbers from P00 to max P99. You can select a
channel by entering the position number in this mode.
◆ C (Real channel mode): You can select a channel by
entering the assigned number to each air broadcasting station
in this mode.
◆ S (Cable channel mode): You can select a channel by
entering the assigned number for each cable channel in this
mode.
21
Assigning Names to Channels
ENG
Channel names will be assigned automatically when channel
information is broadcast. These names can be changed, allowing
you to assign new names.
1
Press the Menu button.
Result:
2
Press the ▼ or ▲ button to select Channel.
Result:
3
4
Press the
button.
button.
The Name menu is displayed with the current channel
automatically is selected.
If necessary, select the channel to be assigned to a new name by
pressing the ▼ or ▲ button. Press the ➛ or ❿ button.
Result:
22
The options available in the Channel group are
displayed.
Press the ▼ or ▲ button to select Name. Press the
Result:
5
The main menu is displayed.
Arrow indications are displayed around the name box.
6
Press the ▼ or ▲ button to select a letter (A~Z), a number (0~9)
or a symbol (-, space). Move on the previous or next letter by
pressing the ➛ or ❿ button.
7
When you have finished entering the name, press the
to confirm the name.
8
Repeat Steps 5 to 7 for each channel to be assigned to a new
name.
button
Activating the Child Lock and Skipping Unwanted Channels
ENG
◆ Activating the child lock
This feature allows you to lock the television so that it cannot
be switched on via the front panel. It can, however, still be
switched on via the remote control. Thus, by keeping the
remote control away from unauthorised users, such as
children, you can prevent them from watching unsuitable
programme.
◆ Skipping unwanted channels
You can exclude the channels of your choice from the
channel scan operation. When you scan through the stored
channels, those that you have chosen to skip are thus not
displayed. All channels that you do not specifically choose to
skip are displayed during scanning.
1
Press the Menu button.
Result:
2
The main menu is displayed.
Press the ▼ or ▲ button to select Channel.
Result:
The options available in the Channel group are
displayed.
3
Press the
4
Press the ▼ or ▲ button to select Channel Edit. Press the
button.
Result:
button.
The Channel Edit menu is displayed with the current
channel automatically is selected.
5
Press the ▼ or ▲ button to select the number of the programme to
which the channel is to be locked. Press the ❿ button.
6
Press the ❿ button.
7
To lock or unlock the channel, select On or Off by pressing the ▼
or ▲ button. Press the
button to confirm.
8
Press the ❿ button.
9
To erase or add the channel, select Erased or Added by pressing
the ▼ or ▲ button. Press the
button to confirm.
10
Repeat Steps 5 to 9 for each channel to be edited.
23
Selecting a Channel by Informations
ENG
You can display the list of stored channels.
Display
P.Size
1
Press the Info. button.
Result:
Text/Mix
Info.
Sleep Perfect Focus
PIP
ON
Scan
Swap
Locate
2
A list is displayed with the first 13 channels. Two text
boxes to the right of the list indicate:
◆ Whether the Teletext feature is available.
◆ Which sound mode is being used.
To...
Then...
Scroll through the
stored channels
Press the ▼ or ▲ button.
Result: The corresponding channel is
displayed.
Select a specific
channel
Press the TV button.
Result: The corresponding channel is
displayed and the Information
box disappears.
➢
◆ External inputs can be displayed and scrolled through
in the same way.
◆ You can display the name of the channel or input by
pressing the Display button.
Changing the Picture Standard
You can select the type of picture which best corresponds to your
viewing requirements.
1
Press the Menu button.
Result:
2
Press the
Result:
TV
Surround
P.STD
S.STD
Mute
S.Mode
Still
VOL
P
24
3
The options available in the Picture group are
displayed.
button.
The Mode is selected.
Select the required picture effect by pressing the ➛ or ❿ button
repeatedly.
Result:
➣
The following picture effects are available:
Dynamic - Standard - Movie - Custom.
You can also set these options simply by pressing the
P.STD (Picture Standard) button.
Adjusting the Picture Settings
ENG
Your television has several settings which allow you to control
picture quality.
1
Press the Menu button.
The options available in the Picture group are
Result:
displayed.
2
Press the
3
Press the ▼ or ▲ button to select Adjust. Press the
Result:
button.
button.
The options available in the Adjust group are
displayed with Color tone is selected.
4
Press the ➛ or ❿ button to select the option (Cool2, Cool1,
Normal, Warm1, Warm2).
5
Press the ▼ or ▲ button to select the option (Contrast,
Brightness, Sharpness, Color or Tint-NTSC only) to be
adjusted. Press the ➛ or ❿ button.
Result:
➣
The horizontal bar is displayed. Move the horizontal
bar’s cursor left or right by pressing the ➛ or ❿
button.
If you make any changes to these settings, the picture
standard is automatically switched to Custom.
Freezing the Current Picture
You can freeze the picture when watching a television programme
simply by pressing the “Still” button.
➣
Mute
Still
VOL
P
To return to normal viewing, press this button again.
Menu
Video
25
Extra Picture Settings
ENG
◆ Scan Mode
You will normally find that scan mode is best set to Natural
to reduce any slight picture flicker. However, it is possible that
some occasional broadcasts (NTSC-M) may benefit by
changing the scan mode. Auto, Natural, Digital and
Progressive modes are available.
◆ Digital NR
If the signal received by your television is weak, you can
activate this feature to reduce any static and ghosting that
may appear on the screen.
◆ Blue Screen
If no signal is being received or the signal is very weak, a blue
screen automatically replaces the noisy picture background.
If you wish to continue viewing the poor picture, you must set
the Blue Screen mode to Off.
◆ LNA
This feature is very useful in the situation that the TV is used
in a weak signal and amplifies the TV signal in the weak
signal area, but not noise.
This feature is working only in a weak signal condition, and
that is memorized on current channel, additional.
1
Press the Menu button.
Result:
2
Press the
3
Select the required option (Scan Mode, Digital NR, Blue Screen
or LNA) by pressing the ▼ or ▲ button.
4
Press the ➛ or ❿ button to change the setting.
◆
◆
◆
◆
26
The options available in the Picture group are
displayed.
button.
Scan Mode : Auto, Natural, Digital, Progressive
Digital NR : Off or On (activating)
Blue Screen : Off or On (activating)
LNA : Off or On (activating)
Selecting the Picture Size (depending on the model)
ENG
You can select the picture size which best corresponds to your
viewing requirements by pressing the “P.Size” button simply.
Depending on the model, the following picture sizes are available:
Auto wide
Expanding and pulling up the picture from 4:3 to
16:9 ratio.
Wide
Adjusting the ratio of picture from 4:3 to 16:9.
Panorama
Adjusting the wide picture to natural size.
Zoom1
Enlarging the normal 4:3 picture by 120%.
Lifting is available.
Zoom2
Enlarging the normal 4:3 picture by 150%.
Lifting is available.
Normal
Normal 4:3 ratio picture.
Cinema
Automatically expanding the broadcasting signal
to approprate picture.
➣
Display
P.Size
Text/Mix
Info.
Sleep Perfect Focus
PIP
ON
Scan
Swap
Locate
The picture size can not be changed in the PIP mode.
◆ Normal (4:3) Model
Normal - Zoom1 - Zoom2 - Cinema
◆ Wide (16:9) Model
Auto wide - Wide - Panorama - Zoom1 - Zoom2 - Normal - Cinema
27
Changing the Sound Standard
ENG
You can select the type of special sound effect to be used when
watching a given broadcast.
TV
Surround
P.STD
S.STD
Mute
1
Press the Menu button.
The main menu is displayed.
Result:
2
Press the ▼ or ▲ button to select Sound.
The options available in the Sound group are
Result:
displayed.
3
Press the
button.
The Mode is selected.
Result:
4
Select the required sound effect by pressing the ➛ or ❿ button
repeatedly.
The following sound effects are available:
Result:
Custom - Standard - Music - Movie - Speech.
S.Mode
Still
VOL
➣
P
You can also set these options simply by pressing the
S.STD (Sound Standard) button.
Adjusting the Sound Settings
The sound settings can be adjusted to suit your personal preferences.
1
Press the MENU button.
The main menu is displayed.
Result:
2
Press the ▼ or ▲ button to select Sound.
The options available in the Sound group are
Result:
displayed.
3
Press the
4
Press the ▼ or ▲ button to select Equalizer. Press the
button.
The options available in the Equalizer group are
Result:
displayed.
5
Select the option to be adjusted by pressing the ➛ or ❿ button.
Press the ▼ or ▲ button to reach the required setting.
➣
28
button.
If you make any changes to these settings, the sound
standard is automatically switched to Custom.
Adjusting the Volume Automatically
ENG
Each broadcasting station has its own signal conditions, and so it
is not easy for you to adjust the volume every time the channel is
changed. This feature lets you automatically adjust the volume of
the desired channel by lowering the sound output when the
modulation signal is high or by raising the sound output when the
modulation signal is low.
1
Press the Menu button.
Result:
2
The main menu is displayed.
Press the ▼ or ▲ button to select Sound.
Result:
The options available in the Sound group are
displayed.
3
Press the
4
Press the ▼ or ▲ button to select Auto Volume.
5
To activate, select On by pressing the ➛ or ❿ button.
button.
Setting the Melody Sound
You can hear clear melody sound when the television is powered
on or off.
1
Press the Menu button.
Result:
2
The main menu is displayed.
Press the ▼ or ▲ button to select Sound.
Result:
The options available in the Sound group are
displayed.
3
Press the
4
Press the ▼ or ▲ button to select Melody.
5
To activate, select On by pressing the ➛ or ❿ button.
button.
29
Setting the Dolby Digital
ENG
Rear of the TV
This mode allows you enjoy Dolby Pro Logic Surround effect fully
with only surround speakers are connected to TV. This allows
various modes for the main, center and rear speakers to be
selected.
Surround Mode
Input Signal
Main
Stereo
Mono
✔
- Phantom
Stereo
Mono
✔
✔
- Wide
Stereo
Mono
✔
3D Sound
Stereo
Mono
✔
✔
Hall
Stereo
Mono
✔
✔
Off
Stereo
Mono
✔
✔
Pro Logic - Normal
Option
➢
Speakers
Center
Rear
✔
✔
✔
✔
✔
✔
✔
✔ ; Sound
1
Press the Menu button.
The main menu is displayed.
Result:
2
Press the ▼ or ▲ button to select Sound.
The options available in the Sound group are
Result:
displayed.
3
Press the
4
Press the ▼ or ▲ button to select Surround. Press the
button.
The Surround menu is displayed with the Mode is
Result:
selected.
5
Select the option by pressing the ➛ or ❿ button. The surround
modes are displayed in the following order.
Pro Logic - 3D Sound - Hall - Off
6
If you select the Pro Logic, the options available are displayed.
7
Press the ▼ or ▲ button to select Pro Logic. Press the ➛ or ❿
button.
8
Select the option by pressing the ➛ or ❿ button. The modes are
displayed in the following order.
Normal - Phantom - Wide
You can also select these options simply by pressing the
Surround button.
button.
➣
9
30
When you are satisfied with the settings, press the
store them.
button to
Adjusting Your Dolby Preferences
ENG
The following Dolby settings can be adjusted to suit your personal
preferences.
◆ Volume of the center and rear speakers
◆ Pro Logic delay time for the rear speakers (between
15 and 30 ms)
◆ Activation/deactivation of the test tone to simulate the
volume on each speaker
1
Press the Menu button.
Result:
2
The main menu is displayed.
Press the ▼ or ▲ button to select Sound.
Result:
The options available in the Sound group are
displayed.
3
Press the
4
Press the ▼ or ▲ button to select Surround. Press the
button.
Result:
button.
The Surround menu is displayed with the Mode is
selected.
5
Select Pro Logic by pressing the ➛ or ❿ button.
6
Select the option (Center, Rear, Time Delay, Test Tone) by
pressing the ▼ or ▲ button. Press the ➛ or ❿ button to reach the
required setting.
7
When you are satisfied with the settings, press the
store them.
➢
button to
Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic”, and the double-D symbol are
trademarks of Dolby Laboratories.
31
Setting the External Sound
ENG
This feature allows you can adjust to suit your personal preferences
when the equipment with output is connected to the television.
1
Press the Menu button.
Result:
2
The main menu is displayed.
Press the ▼ or ▲ button to select Sound.
Result:
The options available in the Sound group are
displayed.
3
Press the
4
Press the ▼ or ▲ button to select Audio Out.
5
Select the required option (Volume or Standard) by pressing the ➛
or ❿ button
button.
◆ If you want to adjust the volume level with the volume control
on the TV or external amplifier, set to Volume.
◆ If you set to Standard...
- You can adjust the volume level with the volume control on
the audio amplifier.
- The volume control buttons (Mute, VOL +/-) of the
television and remote control do not work.
6
32
Press the ▼ or ▲ button to select Int. Mute.
If you set to On, no sound output of internal speaker.
Selecting the Sound Mode (depending on the model)
ENG
The “S.Mode” button displays/controls the processing and output
of the audio signal. When power is switched on, the mode is
automatically preset to either “Dual-I ” or “Stereo”, depending on
the current transmission.
TV
Surround
Regular broadcast
(Standard audio)
MONO (Normal use)
Regular +
NICAM Mono
MONO ↔ MONO
NICAM
(Normal)
NICAM Stereo
STEREO ↔ MONO
NICAM
(Normal)
NICAM Dual-I/II
Dual-I → Dual-II → MONO
NICAM NICAM (Normal)
A2
Stereo
Regular broadcast
(Standard audio)
MONO (Normal use)
Bilingual or Dual-I/II
DUAL-I ↔ DUAL-II
Stereo
➣
Mute
S.Mode
Still
→
On-screen indication
→
NICAM
Stereo
Type of broadcast
P.STD
S.STD
STEREO ↔ MONO
(Forced mono)
◆ If the receiving conditions deteriorate, listening will be
easier if the mode is set to the MONO.
◆ If the stereo signal is weak and an automatic switching
occurs, then switch to the MONO.
◆ When receiving a mono sound in the AV mode, connect
to the “AUDIO-L” input connector on the panel (front or
side). If the mono sound comes out only from left
speaker, press the S.Mode button.
33
Setting the Sleep Timer
ENG
You can select a time period of between 30 and 180 minutes after
the television automatically switches to Standby mode.
Display
P.Size
Text/Mix
Info.
Sleep Perfect Focus
PIP
ON
Scan
Swap
1
Press the Sleep button.
Result:
The Sleep timer menu is displayed.
◆ If the sleep timer is not yet set, Off is displayed.
If the sleep timer is already set, the screen displays
the remaining time and then before the television
will be placed in standby mode.
2
Press the Sleep button repeatedly and cycle through the preset
time intervals (30, 60, 90, 120, 150, 180).
The television automatically switches to standby mode
Result:
when the timer reaches 0.
3
To cancel the sleep timer feature, press the Sleep button
repeatedly and select Off.
Locate
Setting and Displaying the Current Time
You can set the television’s clock so that the current time is displayed
by pressing the “Display” button. You must also set the time if you
wish to use the automatic on or off timers.
➣
Display
When pressing the “ I ” button (On/Off) on the front of
the television, the clock setting will be reset.
1
Press the Menu button.
The main menu is displayed.
Result:
2
Press the ▼ or ▲ button to select Function.
The options available in the Function group are
Result:
displayed.
3
Press the
4
Press the ▼ or ▲ button to select Time. Press the
button.
The options available in the Time group are displayed
Result:
with Clock is selected.
5
Press the ➛ or ❿button to move to the hour or minute.
Set the hour or minute by pressing the ▼ or ▲ button.
6
When you have finished, press the TV button to exit.
7
To...
button.
display the channel information
Once.
display the current time
Twice.
P.Size
remove the display
Text/Mix
Press the “Display” button...
Info.
Sleep Perfect Focus
34
Three times.
Switching the Television On and Off Automatically
ENG
You can set the On/Off timers so that the television will:
◆ Switch on automatically and tune to the channel of your
choice at the time you select
◆ Switch off automatically at the time you select
➣
1
The first step is to set the television’s clock (refer to
“Setting and Displaying the Current Time” on the
previous page).
Press the MENU button.
Result:
2
The main menu is displayed.
Press the ▼ or ▲ button to select Function.
Result:
The options available in the Function group are
displayed.
3
Press the
4
Press the ▼ or ▲ button to select Time. Press the
Result:
button.
The options available in the Time group are displayed.
5
Press the ▼ or ▲ button to select Timer.
6
Press the ➛ or ❿ button to set On
Result:
7
button.
The On Time and Off Time are displayed.
Press the ▼ or ▲ button to select On Time. Set the time at which
you wish the television to be switched on automatically.
◆ Press the ➛ or ❿ button to move to the hour or minute.
Set the hour or minute by pressing the ▼ or ▲ button.
8
Press the ▼ or ▲ button to select Off Time. In the same above,
set the time at which you wish the television to be switched off
automatically.
➣
◆ When leave the television in Standby mode...
- During Timer Off, the LED (Stand-by & Timer indicator)
lights up Red.
- During Timer On, the LED lights up Orange.
◆ When switching the television On during Timer On, the
LED lights up Green.
➣
Absent Power Off
When you set the timer “On”, your television will
eventually be turned off, if you do not operate any controls
during the 3 hours after the TV is turned on by timer.
This function is available in only the timer “On” mode and
will prevent a leakage accident or overheating, caused by
your TV left on for a long time due to the timer “On”
(when you are away on holiday, for example).
35
Viewing the Picture In Picture (PIP)
ENG
You can display a sub picture within the main picture of TV program
or external A/V devices such as VCR or DVD. In this way you can
watch TV program or monitor the video input from any connected
devices while watching TV or other video input.
1
Press the Menu button.
Result:
The main menu is displayed.
2
Press the ▼ or ▲ button to select PIP. Press the
3
Press the ➛ or ❿ button again to set On.
Result:
4
The sources are displayed in the following order:
TV - Ext1 Video - Ext2 Video - Ext3 Video Ext4 Video - S-Video.
Press the ▼ or ▲ button to select Prog.No. If you watching TV
program, select the channel that you want to view through the
sub picture by pressing the ➛ or ❿ button.
➣
6
The options available in the PIP group are displayed.
Press the ▼ or ▲ button to select TV/Video. Find a source of the
sub picture by pressing the ➛ or ❿ button.
Result:
5
button.
When the source of the sub picture (TV/Video) is set to TV,
you can select the channel of sub picture.
Press the ▼ or ▲ button to select Size. Select a size of the sub
picture by pressing the ➛ or ❿ button.
The sizes are displayed in the following order:
Result:
Large - Small - 12 PIP - 3 PIP - Double.
➣◆
12 PIP : You can view up to 12 memorized channels
on the sub picture spontaneously.
◆ On the 12 PIP or 3 PIP mode, it is impossible to
execute swap and locate.
36
Viewing the Picture In Picture (PIP)
ENG
☛
Easy functions of remote control
Buttons
Feature
PIP ON
Used to activate or deactivate the PIP function
directly.
Scan
Used to scan every memorized channel in order.
To stop scanning, press it again.
Swap
Used to interchange the main picture and the
sub picture.
the main picture is in the Video mode
➣ When
and the sub picture is in the TV mode, you
Display
P.Size
Text/Mix
Info.
Sleep Perfect Focus
PIP
ON
Scan
Swap
might not hear the sound of main picture
when pressing the Swap button after
changing the sub picture channel. At this
time, reselect the channel of main picture.
Locate
Used to move the sub picture counterclockwise.
37
Locate
Teletext Feature
ENG
Most television channels provide written information services via
teletext. Information provided includes:
◆ Television programme times
◆ News bulletins and weather forecasts
◆ Sports results
◆ Travel information
This information is divided into numbered pages (see diagram).
Part
Contents
A
Selected page number.
B
Broadcasting channel identity.
C
Current page number or search indications.
D
Date and time.
E
Text.
F
Status information.
FASTEXT information.
➣
Teletext information is often divided between several
pages displayed in sequence, which can be accessed by:
◆ Entering the page number
◆ Selecting a title in a list
◆ Selecting a coloured heading (FASTEXT system)
38
Displaying the Teletext Information
ENG
You can display Teletext information at any time on your television.
Teletext information to be displayed correctly,
☛ For
channel reception must be stable; otherwise:
◆ Information may be missing
TV
Surround
P.STD
S.STD
S.Mode
◆ Some pages may not be displayed
1
Select the channel providing the Teletext service using the P
or P
button.
2
Press the Text/Mix button to activate the teletext mode.
The contents page is displayed. It can be redisplayed
Result:
at any time by pressing the
(index) button.
3
Press the Text/Mix button again.
The screen will be split into two. This Double Teletext
Result:
feature lets you view the actual broadcast and teletext
information separately on the screen.
4
If you wish to display the actual broadcast at the same time as
the teletext page, press the Text/Mix button again.
5
Press the “
Mute
Still
VOL
P
Menu
Video
Text/Mix
Info.
Sleep Perfect Focus
PIP
ON
Scan
Swap
TV” button again to exit from the teletext display.
39
Locate
Selecting Display Options
ENG
Surround
P.STD
S.STD
S.Mode
When you have displayed a Teletext page, you can select various
options to suit your requirements.
To display...
Mute
Still
VOL
P
Menu
Video
Display
P.Size
Text/Mix
Info.
Sleep Perfect Focus
PIP
ON
Scan
Swap
Locate
◆ Hidden text
(answers to quiz games, for example)
(reveal)
◆ The normal screen
(reveal) again
◆ A secondary page
(sub-page)
◆ The broadcast when searching for a page
(cancel)
◆ The next page
(page up)
◆ The previous page
(page down)
◆ Double-size letters in the:
• Upper half of the screen
• Lower half of the screen
(size)
• Once
• Twice
◆ Normal screen
• Three times
➣
40
Press the...
To return to the normal display after using the reveal or
size feature, press the “
TV” button again.
Selecting a Teletext Page
ENG
You can enter the page number directly by pressing the numeric
buttons on the remote control.
1
Enter the three-digit page number given in the content by
pressing the corresponding numeric buttons.
Result:
2
The current page counter is incremented and the
page is then displayed. If the selected page is linked
with several secondary pages, the secondary pages
are displayed in sequence. To freeze the display on a
given page, press the
(hold). Press the it again to
resume.
If the FASTEXT system is used by the broadcasting company,
the different topics covered on a Teletext page are colour-coded
and can be selected by pressing the coloured buttons on the
remote control.
Press the coloured button corresponding to the topic that you wish
to select; the available topics are given on the status line.
Result:
The page is displayed with other colored information
that can be selected in the same way.
3
To display the previous or next page, press the corresponding
coloured button.
4
To display the subpage, see the following steps.
TV
Surround
P.STD
S.STD
Mute
Still
VOL
P
Menu
Video
◆ Press the
(sub-page) button.
Result:
The available subpages appear.
◆ Select the required sub-page. Sub-pages can be scrolled by
pressing the
or
button.
5
When you have finished, press the “
your normal broadcast.
S.Mode
TV” button to return to
41
Connecting to the External Input/Outputs
ENG
➢
EXT1 is used for the equipment with an RGB output,
such as video game devices or video disc players.
VCR
②
①
Rear of the TV
DVD
③
or
Decoder /
Video game device
or
Video disc player
① This end can be fitted with:
◆ A SCART connector
◆ An S-Video connector and two audio RCA connectors (L+R); EXT 2
◆ Three RCA connectors (VIDEO + AUDIO-L and R)
② If you have a second VCR and wish to copy cassette tape, connect the
Satellite receiver
➃
source VCR to EXT1 and the target VCR to EXT2 so that you can redirect
the signal from EXT1 to EXT2.
③ If you have a decoder, connect the decoder to the VCR and the VCR to the
television.
➃ When you wish to record a programme, connect the receiver to EXT1 and
the VCR to EXT2 so that you can redirect the signal from EXT1 to EXT2.
☛
Whenever you connect an audio or video system to your
television, ensure that all elements are switched off.
Refer to the documentation supplied with your equipment
for detailed connection instructions and associated safety
precautions.
42
Connecting to the Audio Output
ENG
➢
The AUDIO OUT RCA connectors are used for equipment, such as an
audio system (to take full advantage of the Surround sound effect).
Rear of the TV
Audio system
Connecting to the RCA Input (depending on the model)
➢
The RCA (VIDEO + AUDIO-L and R) connectors are used for the equipment, such as camcorders,
video disc players, and some video game devices.
Side of the TV
Camcorder
Video game device
Front of the TV
Video disc player
43
Connecting to the S-Video Input (depending on the model)
ENG
➢
The S-VIDEO and RCA (AUDIO-L+R) connectors are used for equipment with an S-Video output,
such as a camcorder or VCR.
Side of the TV
①
Camcorder
and
Front of the TV
①
and
① To play pictures and sound, both the S-VIDEO and RCA connectors must be used.
Connecting Additional Speakers
To take advantage of the surround sound system,
connect additional speakers.
The speaker terminals are located on the rear of
the television:
◆ Two for the left-hand surround speaker
(marked L)
◆ Two for the right-hand surround speaker
(marked R)
◆ Two for the center speaker (marked C) ;
Option
➢
To improve the quality of the sound, connect the:
◆ Red wire to the red terminal
◆ Black wire to the black terminal
44
Rear of the TV
VCR
Viewing Pictures From External Sources
ENG
Once you have connected up your various audio and video systems,
you can view different sources by selecting the appropriate input.
TV
Surround
1
Check that all the necessary connections have been made.
2
Switch your television on, then press the VIDEO button
repeatedly.
Result:
➣
➣
The input sources are displayed in the following
order:
TV - EXT1 - EXT2 - EXT3 - EXT4 - S-Video.
P.STD
S.STD
Mute
S.Mode
Still
VOL
P
Menu
Video
Depending on the source selected, the pictures may appear
automatically.
To watch television programmes again, press the TV
button and select the number of the channel required.
45
Redirecting an Input to the External Output
ENG
Your television enables you to choose which audio/video signals
are output to the external connector.
1
Press the Menu button.
Result:
2
Press the ▼ or ▲ button to select Function.
Result:
The options available in the Function group are
displayed.
3
Press the
4
Press the ▼ or ▲ button to select AV Setup. Press the
button.
Result:
button.
The options available in the AV Setup group are
displayed.
5
Select the required output (EXT1, EXT2 or EXT3) by pressing the ▼
or ▲ button.
6
Select the source to be directed to the output by pressing the ➛ or
❿ button.
➣
46
The main menu is displayed.
EXT1, EXT2 : Default
EXT3 : Variable
Programming the Remote Control for Other Components
ENG
This TV’s remote control can operate almost any VCR, Cable box,
or DVD, in addition to controlling the TV.
➣
The remote control might not be compatible with the TV
manufactured by another company.
Power
TV
1
Turn off your VCR, Cable box, or DVD.
2
Press the appropriate button among the component selection
buttons to activate another component (TV, VCR, Cable, DVD).
VCR
Cable
Example: If you want to program the remote control to operate
your VCR, press the VCR button on the remote
control.
3
Press the SET button.
4
Use the numeric buttons to enter the code by manufacturer. Each
code must be three digits long.
Example: To enter the code “6”, press 0, 0, and 6.
To enter the code “76”, press 0, 7, and 6.
➣
5
Press the Power ( ) button on the remote control.
The component you select should turn on. If it turns on, your
remote control is now set correctly.
➣
6
See the remote control code tables to find the appropriate
code for your particular component. If more than one code
is listed, try each one separately until you find the one that
works.
If it does not turn on, repeat steps above, but try one of the
other codes listed for the brand of particular yours. If no
other codes are listed, try each code, “000” through “089”
for VCR/DVD and “000” through “077” for Cable box.
Once your remote control is set up, press the SET button any time
you want to use the remote to operate your Cable box, VCR or
DVD.
➣
◆ When your remote control is in the VCR, Cable, or DVD
mode, the volume buttons still control your TV’s volume.
◆ When your remote control is in the TV or Cable mode,
the VCR or DVD control buttons (PLAY, PAUSE, etc.)
still operate your VCR or DVD.
47
DVD
SET
Programming the Remote Control for Other Components
ENG
TV Remote Control Codes
A-Mark
88, 37, 90
MTC
26, 15, 6, 49, 93, 20, 8, 75
Admiral
55
NEC
25, 75, 20, 8, 6, 5, 1, 1
20, 6
Nikei
50
Onking
50
Akai
37, 47, 64, 41, 50
Anam
Onwa
50
67
Optonica
69
68
Panasonic
6, 37, 20, 56
Aoc
Bell & Howell
Broksonic
6, 12, 20, 46, 50
Candle
Penney
64, 72, 58, 82
61, 6, 49, 66, 18, 90, 50, 77, 25
45
Philco
1, 8, 88, 61, 6, 90, 50, 12, 98, 92, 100, 82, 20
Citizen
20, 46, 6, 50, 12, 90, 45, 9, 10
Philips
88, 1, 61, 6, 90, 12, 98, 92, 82, 20, 5, 57
Classic
50
Pioneer
65, 26
6
Portland
88, 6, 90
Centrion
Concerto
Contec
Coronado
50, 78, 83, 81
Proton
1, 31, 6, 90, 77, 78
88, 90
Quasar
72, 58
7, 49, 50
Craig
Radio Shack
Croslex
30
RCA
Crown
50
Realistic
Curtis-Mathes
1, 6, 20, 90, 17, 31
50
CXC
88, 1, 93, 31, 32, 33, 38, 52, 2, 3, 92, 34,
Daewoo
Sampo
Samsung
Sanyo
50, 92, 25, 90
61, 6, 71, 66, 87, 20, 90, 1, 62
8, 49, 50, 25
1, 20, 90, 6, 19, 26, 49
88, 0, 61, 28, 44, 29, 81, 48, 49, 90, 92, 51
89, 80, 62, 78, 13, 14
46, 50, 35, 36, 4, 5, 6, 8
Scott
1, 50, 19, 90, 6
Daytron
1, 6, 20
Sears
88, 61, 6, 8, 90, 91, 89, 80, 15, 19
Dynasty
50
Sharp
88, 90, 85, 24, 25, 69
88, 1, 90, 50, 83, 19, 30, 81, 20, 6, 25, 55,
Emerson
23, 36
Fisher
8, 80, 61, 15, 125
Funai
50, 19, 69, 6
General Electric
1, 61, 72, 50, 58, 17, 18, 6, 49, 19, 90
88, 27, 1, 37, 10, 11, 42, 90, 39, 40, 92, 99
Goldstar
Signature
Sony
Soundesign
Spectricon
SSS
Sylvania
Symphonic
Hitachi
88, 6, 90, 71, 77, 70, 21, 22, 23, 25
Infinity
82
Tatung
JBL
82
Techwood
JC Penney
91, 92, 17, 20
60, 16, 128, 129
JVC
Kloss
92
KMC
88, 90, 13
KTV
88, 90, 50, 61, 20
48
Teknika
Telefunken
Telerent
TMK
84, 6, 114
77, 74
1, 50, 12, 6, 19
37
6, 50
1, 61, 6, 12, 98, 92, 20, 100, 82
2, 6, 90, 12, 20
72, 69
6, 59
88, 46, 6, 90, 50, 12, 19, 94, 84
96, 97
84
1, 6, 90
Programming the Remote Control for Other Components
ENG
VCR Remote Control Codes
Admiral
15, 88
Aiwa
24
Akai
26, 31, 32
Audio Dynamics
22, 25
MTC
Multitech
NEC
11
Panasonic
Broksonic
19
Pentax
Candle
16, 18 ,22, 54, 55, 61
Canon
17, 62
Philco
Citizen
16, 18, 22, 54, 55, 61
Philips
Craig
Curtis-Mathes
Daewoo
DB
11, 23, 25, 39, 55, 70, 73
15
17, 62, 84, 86
14, 44
55
Pentex Research+
17, 38, 62, 65
17
23
Pioneer
14, 25, 42, 59
16, 21
Portland
53, 54, 61
9, 16, 17, 23, 24, 55, 62, 73, 76
Proscan
9
3, 4, 5, 6, 7, 8, 22, 54, 85
Quartz
11
23, 25
Quasar
17, 53
Dimensia
9
Dynatech
24
RCA
Electrohome
36
Samsung
Emerson
16, 24, 40, 41
Optimus
Bell & Howell
Colortyme
16, 24
Radio Shack/Realistic
11, 15, 17, 18, 21, 24, 28, 36, 52, 62
9, 14, 16, 17, 37, 44, 46, 63, 78
0, 16, 22, 31, 41, 51
17, 18, 19, 22, 24, 29, 32, 36, 43, 50, 51,
Sansui
25
56, 58, 66, 71, 74, 76, 77, 79
Sanyo
11, 21
Fisher
11, 21, 27, 28, 52, 57, 67
Scott
22, 50, 58, 77
Funai
24
Sears
11, 14, 18, 21, 27, 28, 44, 52, 57
9, 16, 17, 41, 62
Sharp
15, 36, 48, 54
Shintom
26, 35, 40, 64
General Electric
Go Video
Goldstar
Harman Kardon
Hitachi
Instant Replay
JC Penney
JCL
Kenwood
KLH
LG
16
18, 23, 55, 69
23
14, 24, 44, 45
17
11, 14, 16, 17, 23, 25, 39, 44, 60, 62
11, 17, 23, 25, 39, 55
11, 23, 25, 39, 55
82
1, 2, 7
Sylvania
11, 24
39
Tatung
24, 39, 78
Teac
17
Technics
Teknika
TMK
40
Toshiba
24
Toshiko
Marantz
24
Tandy
24
17, 38, 62, 65
17, 24, 38, 62, 65
Symphonic
Logik
Magnavox
26, 35, 47
Sony
Lloyd
LXI
24
Signature
17, 18, 24, 30
76
14, 22, 28, 57, 58
18
16,18
Totevision
11, 17, 23, 25, 38, 39, 55, 70
49
Programming the Remote Control for Other Components
ENG
Cable Box (CATV) Remote Control Codes
Anvision
15, 16
Pioneer
26, 28, 52
Cable Star
15, 16
Randtek
15, 16
DaeHan
5
RCA
8, 35, 74
DaeRyung
3
Regal
11, 20, 21
4
Regency
Dongkuk
Eagle
10, 41
15, 16
SAEWOO
7
Eastern International
20
Samsung
0, 11, 30, 52, 71, 72
General Instrument
54
Signature
54
Spruce
35
Starcom
54
GI
12, 13, 23, 31, 32, 33, 38, 44, 75, 76, 77
Hamlim
11, 12, 20, 21, 42, 56
Hitachi
45, 51, 54
Jerrold
12, 13, 23, 31, 32, 33, 38, 44, 54, 70, 73
LG
6
Macom
45, 51
Magnavox
Nawoo
15, 16, 27, 29, 34, 36, 37, 40, 41, 48, 49
1
Stargate2000
Sylvania
TaePyungYang
Texscan
Tocom
Unika
66
19, 67
2
19, 67
25, 29, 57, 58, 63
39, 40, 49
NSC
17
Universal
59, 60
Oak
24, 46
Viewstar
15, 16, 27, 29, 34, 36, 37, 40, 41, 48, 49
Osk Sigma
Panasonic
Philips
24
11, 35, 47, 69
Warner Amex
Zenith
52
22, 50, 65, 69
15, 16, 27, 29, 34, 36, 37, 40, 41, 48, 49
DVD Remote Control Codes
Philips
7
ProScan
8
Sony
4
RCA
8
Samsung
0
Toshiba
2
Panasonic
6
Sharp
5
LG
1
CurtisMathes
9
JVC
3
50
SCART Connector Wiring (EXT1, EXT2 or EXT3)
ENG
If you wish to connect other equipment via the SCART connectors on your television, contact your
dealer or a qualified technician to wire the A/V cable as illustrated below.
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
➢
Signal
Audio output R
Audio input R
Audio output L
Audio chassis return
Video chassis return (RGB blue)
Audio input L
RGB blue input
Switching voltage
Video chassis return (RGB green)
AV-Link (Ext 1)
RGB green input
Video chassis return (RGB red)
RGB red input
Blanking signal (RGB switching)
Video chassis return
Blanking signal ground
Video output
Video input
Screening/chassis return
Pins 5, 7, 9, 11, 13, 15 and 16 are used for RGB processing and are only wired
on the EXT1 or EXT3 connector.
51
Troubleshooting: Before Contacting Service Personnel
ENG
Before contacting Samsung after-sales service, perform the following simple checks.
If you cannot solve the problem using the instructions below, note the model and serial number of the
television and contact your local dealer.
No sound or picture
◆ Check that the mains lead has been connected to a wall socket.
◆ Check that you have pressed the “ I ” button (On/Off) and the
Power ( ) button.
◆ Check the picture contrast and brightness settings.
◆ Check the volume.
Normal picture but no sound
◆ Check the volume.
◆ Check whether the volume Mute button on the remote control has
been pressed.
No picture or black and white picture
◆ Adjust the colour settings.
◆ Check that the broadcast system selected is correct.
Sound and picture interference
◆ Try to identify the electrical appliance that is affecting the television,
then move it further away.
◆ Plug your television into a different mains socket.
Blurred or snowy picture,
distorted sound
◆ Check the direction, location and connections of your aerial.
This interference is often occurs to the use of an indoor aerial.
Remote control malfunctions
◆ Replace the remote control batteries.
◆ Clean the upper edge of the remote control (transmission window).
◆ Check the battery terminals.
52
Wiring the Mains Power Supply Plug (UK Only)
ENG
IMPORTANT NOTICE
The mains lead on this equipment is supplied with a moulded plug incorporating a fuse. The value of the fuse is
indicated on the pin face of the plug and, if it requires replacing, a fuse approved to BSI1362 of the same rating
must be used.
Never use the plug with the fuse cover omitted if the cover is detachable. If a replacement fuse cover is required,
it must be of the same colour as the pin face of the plug. Replacement covers are available from your dealer.
If the fitted plug is not suitable for the power points in your house or the cable is not long enough to reach a power
point, you should obtain a suitable safety approved extension lead or consult your dealer for assistance.
However, if there is no alternative to cut off the plug, remove the fuse and then safely dispose of the plug.
Do NOT connect the plug to a mains socket as there is a risk of shock hazard from the bared flexible cord.
IMPORTANT
The wires in the mains lead are coloured in accordance with the following code:
BLUE - NEUTRAL
BROWN - LIVE
As these colours may not correspond to the coloured markings identifying the terminals in your plug, proceed as
follows:
The wire coloured BLUE must be connected to the terminal marked with the letter N or coloured BLUE or BLACK.
The wire coloured BROWN must be connected to the terminal marked with the letter L or coloured BROWN or RED.
WARNING: DO NOT CONNECT EITHER WIRE TO THE EARTH TERMINAL, WHICH IS MARKED WITH THE
LETTER E OR BY THE EARTH SYMBOL , OR COLOURED GREEN OR GREEN AND YELLOW.
53
Memo
ENG
54
Memo
ENG
55
- AFTER SALES SERVICE
- Do not hesitate to contact your retailer or service agent
if a change in the performance of your product indicates
that a faulty condition may be present.
ELECTRONICS
BP68-00070A-01 (ENG)
Download PDF

advertising