Samsung | PS-42V4S | Samsung PS-42V4S Benutzerhandbuch

BN68-00630T-01Eng_1115
11/16/04
4:35 PM
Page 1
PDP-TELEVISION
(PLASMA DISPLAY PANEL)
Owner’s Instructions
Before operating the unit,
please read this manual thoroughly,
and retain it for future reference.
ON-SCREEN MENUS
PICTURE IN PICTURE (PIP)
TELETEXT
BN68-00630T-01Eng_1115
11/16/04
4:35 PM
Page 2
Important !
ENG
◆ Screen Image retention
Do not display a still image (such as on a video game) on the plasma
monitor panel for more than 2 hours as it can cause screen image
retention. This image retention is also known as “screen burn”. To
avoid such image retention, reduce the degree of brightness and
contrast of this screen when displaying a still image.
◆ Cell Defect
The plasma display panel consists of fine cells. Although the panels
are produced with more than 99.9 percent active cells, there may be
some cells that do not produce light or remain lit.
◆ Height
The PDP can normally operate only under 2000m in height. It might
abnormally function at a place over 2000m in height and do not
install and operate there.
◆ Warranty
- Warranty does not cover any damage caused by image retention.
- Burn-in is not covered by the warranty.
2
BN68-00630T-01Eng_1115
11/16/04
4:35 PM
Page 3
Checking Parts
ENG
Sold Separately
S-VIDEO Cable
Owner’s Instructions
DVI Cable
Remote Control/
AAA Batteries
Component Cables
(RCA)
Power Cord
Antenna Cable
Ferrite Cores for
Speaker Wire
Speaker Wires
Scart Cable
3
BN68-00630T-01Eng_1115
11/16/04
4:35 PM
Page 4
ENG
Contents
◆ FOREWORD
■
■
Important ! .....................................................................................................
Checking Parts ..............................................................................................
2
3
◆ CONNECTING AND PREPARING YOUR DISPLAY
■
■
■
■
■
■
■
■
■
■
■
■
■
Your New Plasma Display Panel...................................................................
Infrared Remote Control ................................................................................
Inserting the Batteries in the Remote Control................................................
Assembling the Stand-Base ..........................................................................
Installing the Display on the Wall Attachment Panel .....................................
Connecting Speakers ....................................................................................
Connecting to an Aerial or Cable Television Network ...................................
Connecting a Satellite Receiver or Decoder..................................................
Switching On and Off.....................................................................................
Placing in Standby Mode...............................................................................
Becoming Familiar with the Remote Control .................................................
Plug & Play Feature.......................................................................................
Choosing Your Language..............................................................................
6
8
9
9
10
12
14
14
15
15
16
17
18
◆ SETTING THE CHANNELS
■
■
■
■
■
■
■
■
Storing Channels Automatically.....................................................................
Storing Channels Manually............................................................................
Skipping Unwanted Channels .......................................................................
Sorting the Stored Channels .........................................................................
Assigning Names to Channels ......................................................................
Activating the Child Lock ...............................................................................
Displaying Information ...................................................................................
Using the LNA (Low Noise Amplifier) Feature...............................................
19
20
22
23
24
25
26
36
◆ USING YOUR DISPLAY (continued)
■
■
■
■
■
■
■
■
■
■
■
■
■
■
4
Changing the Picture Standard .....................................................................
Adjusting the Picture Settings........................................................................
Adjusting the Picture Settings (DVI Mode) ....................................................
Using the Fine Tune ......................................................................................
Viewing the Channel Scan Picture ................................................................
Freezing the Current Picture .........................................................................
Selecting the Picture Size..............................................................................
Selecting the Film Mode ................................................................................
DNIeTM (Digital Natural Image engine
) ...............................................
Setting the Blue Screen.................................................................................
Setting the Melody Sound .............................................................................
Viewing the Picture In Picture (PIP) ..............................................................
Using the Digital NR (Digital Noise Reduction) Feature ................................
Changing the Sound Standard ......................................................................
26
27
28
29
30
30
31
32
32
33
33
34
36
37
BN68-00630T-01Eng_1115
11/16/04
4:35 PM
Page 5
ENG
Contents (continued)
◆ USING YOUR DISPLAY
■
■
■
■
■
■
■
■
■
■
Adjusting the Sound Settings ........................................................................
Adjusting the Volume Automatically ..............................................................
Setting the TruSurround XT...........................................................................
Selecting the Internal Mute............................................................................
Selecting the Sound Mode (depending on the model) ..................................
Setting the Sleep Timer .................................................................................
Setting and Displaying the Current Time.......................................................
Switching the Television On and Off Automatically .......................................
Viewing an External Signal Source ...............................................................
Redirecting an Input to the External Output ..................................................
38
38
39
39
40
41
42
43
44
45
◆ USING THE TELETEXT FEATURE
■
■
■
■
Teletext Feature ............................................................................................
Displaying the Teletext Information ...............................................................
Selecting Display Options..............................................................................
Selecting a Teletext Page..............................................................................
46
47
48
49
◆ ADDITIONAL INFORMATION AND CONNECTIONS
■
■
■
■
■
■
Connecting to the External Devices ..............................................................
Connecting to the S-Video Input....................................................................
Connecting to the DVI Input ..........................................................................
Connecting to the Component Input..............................................................
Connecting and Using the Home Theater System ........................................
Pin Configurations .........................................................................................
50
51
52
53
54
55
◆ RECOMMENDATIONS FOR USE
■
Troubleshooting: Before Contacting Service Personnel................................
Symbols
Press
☛
Important
➢
Note
5
56
BN68-00630T-01Eng_1115
11/16/04
4:35 PM
Page 6
Your New Plasma Display Panel
➢
ENG
The actual configuration on your PDP may be different,
depending on your model.
Front Panel
a
b
c
b
a
Power Indicator
- Power Off; Red
- Power On; Off
- Timer On; Green
SOURCE
External input selection.
When the Main menu is displayed on screen, the
Main menu is not operated with source key.
c
MENU
Menu display and exit.
Remote Control Signal Receiver
-
Aim the remote control towards this spot on the
PDP.
+
Volume adjustment.
C/P.
Channel selection. Auto power On.
I/
Press to turn the PDP on and off.
6
BN68-00630T-02Eng_0104
1/5/05
8:37 AM
Page 7
Your New Plasma Display Panel (continued)
➢
The actual configuration on your PDP may be different,
depending on your model.
ENG
Rear Panel
➢
For further details about connection, refer to pages 50~54.
a) DVI INPUT
Connect to digital video output jack for device
with DVI output. (Not compatible with PC)
b) MONITOR OUT (VIDEO / L-AUDIO-R)
Outputs for external devices
c) Ext.1, Ext.2
Inputs or outputs for external devices, such as
VCR, DVD, video game device or video disc
players.
g) COMPONENT
Video (Y/Pb/Pr) and audio (L-AUDIO-R) inputs for
Component.
h) ANT IN VHF/UHF (75Ω)
75Ω Coaxial connector for Aerial/Cable Network.
i) EXT SPEAKER(8Ω)
Connectors for external speakers.
j) POWER IN
Connect the supplied power cord.
d) ONLY FOR SERVICE
Connector for service only.
e) S-VIDEO
Video and audio inputs for external devices with
an S-Video output, such as a camcorder or VCR.
f) AV (VIDEO / L-AUDIO-R )
Video and audio inputs for external devices, such
as a camcorder or VCR.
7
BN68-00630T-01Eng_1115
11/16/04
4:35 PM
Page 8
Infrared Remote Control
ENG
TURNS THE PDP ON AND OFF
DIRECT CHANNEL SELECTION
TUNES TO THE PREVIOUS CHANNEL
EXTERNAL INPUT SELECTION/
TELETEXT PAGE HOLD
VOLUME INCREASE
TEMPORARY SOUND SWITCH-OFF
VOLUME DECREASE
AUTOMATIC SWITCH-OFF/
TELETEXT STORE
(DEPENDING ON THE MODEL)
MENU DISPLAY/
TELETEXT INDEX
NEXT CHANNEL/
TELETEXT NEXT PAGE
PRESS TO SELECT ALL OF THE
AVAILABLE VIDEO SOURCES/
TELETEXT MODE (LIST/FLOF)
SELECTION (DEPENDING ON THE MODEL)
PREVIOUS CHANNEL/
TELETEXT PREVIOUS PAGE
INFORMATION DISPLAY/
TELETEXT REVEAL
TV MODE SELECTION
EXIT TELETEXT
(DEPENDING ON THE MODEL)
MOVE TO THE REQUIRED
MENU OPTION/
ADJUST AN OPTION VALUE
RESPECTIVELY
CONFIRM YOUR CHOICE
(STORE OR ENTER)
SOUND MODE SELECTION/
TELETEXT SUB-PAGE
PICTURE SIZE/
TELETEXT SIZE SELECTION
TELETEXT DISPLAY/
MIX BOTH TELETEXT INFORMATION
AND THE NORMAL BROADCAST
PICTURE STILL/
TELETEXT CANCEL
SOUND EFFECT SELECTION
PICTURE EFFECT SELECTION
➢
8
The performance of the remote control may be affected by bright light.
BN68-00630T-01Eng_1115
11/16/04
4:35 PM
Page 9
Inserting the Batteries in the Remote Control
ENG
You must insert or replace the batteries in the remote control when
you:
◆ Purchase the PDP
◆ Find that the remote control is no longer operating
correctly
1
Remove the cover on the rear of the remote control by pressing
the symbol ( ) downwards and then pulling firmly to remove it.
2
Insert two R03, UM4, “AAA” 1.5V or equivalent batteries taking
care to respect the polarities:
◆ - on the battery against - on the remote control
◆ + on the battery against + on the remote control
3
Replace the cover by aligning it with the base of the remote
control and pressing it back into place.
)
Assembling the Stand-Base (Option)
The stand base will be sold separately depending on model.
1
Assemble two support pins with the stand base and firmly secure
both sides of the support pins using 8 screws provided.
2
Assemble the PDP with the stand and firmly secure the PDP using
4 screws provided.
➢
◆ Two or more people should carry the PDP. Never lay the
PDP on the floor because of possible damage to the screen.
Always store the PDP upright.
9
BN68-00630T-01Eng_1115
11/16/04
4:35 PM
Page 10
Installing the Display on the Wall Attachment Panel
ENG
Installation Notes
◆ Do not install the PDP on any place other than vertical walls.
◆ To protect the performance of the PDP and prevent troubles, avoid the followings:
- Do not install next to smoke and fire detectors.
- Do not install in an area subjected to vibration or high voltage.
- Do not install near or around any heating apparatus.
◆ Use only recommended parts and components.
Mounting Kits (Sold Separately)
Wall Mount Bracket
Plastic Hanger
Screws
4 EA
4 EA
How to Adjust Mounting Angle
(depending on your model)
The wall mount bracket is delivered
separately. Please tighten the captive
screw in the direction of the arrow after
assembling the bracket.
10
1
Secure the PDP to the wall mount bracket.
(Please refer to the following instructions.)
2
Set the angle by pulling the upper end of the
PDP attached to bracket in the direction of the
arrow.
3
The angle can be adjusted from 0° to 15° by
±2°.
BN68-00630T-01Eng_1115
11/16/04
4:35 PM
Page 11
Installing the Display on the Wall Attachment Panel (continued)
➢
The exterior of the PDP may be different than the picture.
(Assembly and installation of the plastic hanger is the same.)
1
Remove the screws from the back of the PDP.
2
ENG
Use the screws and assemble the plastic
hanger.
☛
◆ Please ask the installers to install the
wall mount bracket.
◆ Please be sure to check if the plastic
hanger is completely secured on both
the left and right side after hanging
the PDP on the wall mount bracket.
◆ Please avoid catching your fingers
while installing and adjusting the
angle.
◆ Please tightly secure the wall mount
bracket to the wall to avoid injury
from a falling PDP.
3
Tighten the screws of the plastic hanger to the
back side of the PDP.
4
Put the 4 pegs on the PDP in the grooves of the wall mount bracket and pull down on the PDP (!) to
secure it to the wall mount bracket (@). Tighten the screws as shown (#) so that the PDP cannot be
separated from wall mount bracket.
PDP panel
Wall
Wall attachment panel bracket
Connecting External Devices to the PDP
◆ To connect external devices such as a DVD or a Home Theater System to the PDP, please refer
to following instructions:
1
Be sure to remove the safety pins underneath the PDP.
◆ If the safety pins are not removed, the angle cannot be adjusted.
Any attempt to do so may cause damage to the PDP.
2
Pull out the bottom of the PDP (which has been attached to the Wall
Mount Bracket) in the direction indicated by the arrows (refer to
the illustration) until it clicks.
◆ Using the PDP After Connecting External Devices.
Be sure to secure the PDP by inserting the 2 safety pins after
o
readjusting the angle of the PDP to 0 .
◆ For safety, be sure to secure the PDP using the safety pins.
If the safety pins are not used, the PDP may fall, causing serious
injury.
11
BN68-00630T-01Eng_1115
11/16/04
4:35 PM
Page 12
Connecting Speakers
ENG
1
Remove the screws on the rear of the PDP.
2
Hang the two “T” shaped hangers
on the square holes on the rear of
the PDP.
3
Tighten the PDP and the speaker bracket using the screws removed from the PDP.
➢
When moving your PDP, do NOT hold the speaker connected to your PDP. It may damage the
bracket clamping the speaker and your PDP together and result in a drop of your PDP and a risk of
personal damage and injury.
12
BN68-00630T-01Eng_1115
11/16/04
4:35 PM
Page 13
Connecting Speakers (continued)
ENG
Connect the speaker audio cable to the external speaker output jack on the rear of the PDP matching
the “+” and “-” ends of the cable with the diagram on the PDP.
➢
➢
◆ The speakers MUST have to a power handling capability of 10 watts minimum (impedance 8Ω).
◆ When you connect the speaker wire to the external speaker out connector, first bind the speaker wire
round the ferrite core to secure it.
Before connecting the speaker wire to the PDP, turn off your PDP.
Ferrite Cores
The ferrite cores are used to attenuate undesired signals.
When connecting cables, attach one of these ferrite cores to
the cable near the connector.
13
BN68-00630T-01Eng_1115
11/16/04
4:35 PM
Page 14
Connecting to an Aerial or Cable Television Network
ENG
To view television channels correctly, a signal must be received by
the set from one of the following sources:
◆ An outdoor aerial
◆ A cable television network
◆ A satellite network
Rear of the PDP
or
Cable Television
Network
1
In the first three cases, connect the aerial or network input cable to
the 75Ω coaxial socket on the rear of the PDP.
2
If you are using an indoor aerial, you may need to turn it when
tuning your PDP until you obtain a picture that is both sharp and
clear.
For further details, refer to:
◆ “Storing Channels Automatically” on page 19
◆ “Storing Channels Manually” on page 20
➢
When installing or re-installing your PDP, be sure to use the
supplied coaxial antenna cable. If you connect using a different
coaxial cable, there is risk of noise or interference to the screen
image. (You must not use another general purpose cable.)
Connecting a Satellite Receiver or Decoder
Rear of the PDP
In order to watch television programmes broadcast via a satellite
network, you must connect a satellite receiver to the rear of the
PDP. Also, in order to descramble a coded transmission signal, you
must connect a decoder to the rear of the PDP.
Using a Coaxial cable
Connect a coaxial cable to the:
◆ Receiver (or Decoder) output socket.
◆ Television aerial input socket.
➢
If you wish to connect both a satellite receiver (or decoder)
and a VCR, you should connect the:
◆ Receiver (or Decoder) to the VCR
◆ VCR to the PDP
Otherwise, connect the receiver (or decoder) directly to the
PDP.
Satellite receiver/
Decoder
14
BN68-00630T-01Eng_1115
11/16/04
4:35 PM
Page 15
Switching On and Off
ENG
The mains lead is attached to the rear of your PDP.
1
Plug the mains lead into an appropriate socket.
Result:
➢
2
Front of the PDP
The Standby indicator on the front of the PDP lights up.
The main voltage is indicated on the rear of the PDP and
the frequency is 50 or 60Hz.
Press the “ I / ” button on the front of the PDP (or POWER (
button on the remote control) to switch the PDP on.
Result:
)
The programme that you were watching last is reselected automatically.
you have not yet stored any channels, No clear picture
➣ Ifappears.
Refer to “Storing Channels Automatically” on page
19 or “Storing Channels Manually” on page 20.
3
To switch your PDP off, press the “ I /
” button again.
Placing in Standby Mode
Your PDP can be placed in Standby mode, in order to reduce the
Power consumption.
The Standby mode can be useful when you wish to interrupt
viewing temporarily (during a meal, for example).
1
Press the POWER (
Result:
2
) button on the remote control.
The screen is turned off and the Standby indicator on
the front of the PDP lights.
To switch the PDP back on, simply press the POWER (
again or a numeric button.
➣ You can also switch on by pressing the P
or
) button
button.
15
BN68-00630T-01Eng_1115
11/16/04
4:35 PM
Page 16
Becoming Familiar with the Remote Control
ENG
The remote control is used mainly to:
◆ Change channels and adjust the volume
◆ Display the on-screen menu system
The following table presents the most frequently used buttons and
their functions.
Button
to
SLEEP
Menu Function
Used to display the next
stored channel.
-
Used to display the
previous stored channel.
-
Used to display the corresponding channels.
For double digit channels, the second digit must be
pushed immediately after the first. Failure to do this will
result in a single digit channel being displayed.
➢
Used to select a preset time interval (off - 30 - 60 - 90 - 120 150-180).
Used to increase the
volume.
-
Used to decrease the
volume.
-
MUTE
Used to switch the sound off temporarily.
To turn the sound back on, press this button again, or
press the
or
button.
MENU
Used to display the
on-screen menu system.
Used to return to the previous
menu or normal viewing.
-
Used to:
◆ Display a submenu
containing selections for
the current menu option
◆ Increase/decrease a
menu option value
-
Used to confirm your choice.
-
Used to exit from the menu
system and return to normal
viewing directly.
EXIT
16
Viewing Function
➣
BN68-00630T-01Eng_1115
11/16/04
4:35 PM
Page 17
Plug & Play Feature
ENG
When the television is initially powered ON, several basic customer
settings proceed automatically and subsequently. The following
settings are available.
Plug & Play
Press ENTER to Start Plug & Play
Start
1
If the television is in Standby mode, press the POWER (
on the remote control.
Enter
) button
Exit
Language
Result:
The message Plug & Play is displayed. It flickers for
a little while, and then the Language menu is
automatically displayed.
2
Select the appropriate language by pressing the † or … button.
3
Press the ENTER (
Result:
4
) button to confirm your choice.
The message Antenna input check is displayed.
The Country menu is displayed.
5
Select your country by pressing the † or … button.
6
Press the ENTER (
Result:
Result:
➢
8
9
Antenna Input Check
Country
) button to confirm your choice.
Country
Austria
Belgium
Croatia
Denmark
Finland
France
Germany
▼ More
The Auto Store menu is displayed.
To start the search, press the ENTER (
) button.
The search will end automatically. Channels are sorted
and stored in an order which reflects their position in
the frequency range (with lowest first and highest last).
When it has finished, the Clock Set menu is displayed.
To stop the search before it has finished or return to normal
viewing, press the MENU (
) button.
) button to set the Clock.
Press the ENTER (
Press the œ or √ button to move to the hour or minute.
Set the hour or minute by pressing the † or … button.
When it has finished, the message Enjoy Your Watching is
displayed, and then the channel which has been stored will be
activated.
Enter
Plug & Play
Make sure that the antenna is connected to the TV, and then
press the ENTER (
) button.
Result:
7
Move
Move
Enter
Auto Store
Press ENTER to start channel memory
40 MHz
0%
Start
Enter
Stop
Auto Store
Channel store in process.
Storing.
57 MHz
1%
Stop
Enter
Stop
Clock
Hour
Min
01
00
Adjust
Move
Stop
Enjoy Your Watching
17
BN68-00630T-01Eng_1115
11/16/04
4:35 PM
Page 18
Plug & Play Feature (continued)
ENG
If you want to reset this feature...
TV
Setup
√
Time
Language
: English
√
AV Setup
Digital NR
: On
Enter
TV
Press the MENU button.
The main menu is displayed.
Result:
√
2
Press the † or … button to select Setup.
The options available in the Setup group are displayed.
Result:
3
Press the ENTER (
4
Press the † or … button to select Miscellaneous. Press the
ENTER (
) button.
The options available in the Miscellaneous group are
Result:
displayed.
5
Press the † or … button to select Plug & Play. Press the
ENTER (
) button.
√
Miscellaneous
Move
1
√
Return
Miscellaneous
Melody
: Off
Blue Screen
√
√
Plug & Play
: Off
√
Result:
6
Move
Enter
) button.
The message Plug & Play is displayed.
For further details on how to set, refer to the opposite page.
Return
Choosing Your Language
TV
Setup
√
Time
Language
: English
√
√
AV Setup
Digital NR
: On
Enter
TV
1
Press the MENU button.
The main menu is displayed.
Result:
2
Press the † or … button to select Setup.
The options available in the Setup group are displayed.
Result:
3
Press the ENTER (
4
Press the † or … button to select Language. Press the ENTER
(
) button.
The languages available are listed.
Result:
5
Select the appropriate language by pressing the † or … button.
6
Press the ENTER (
7
When you are satisfied with your choice, press the EXIT (
button to return to normal viewing.
√
√
Miscellaneous
Move
When you start using your television for the first time, you must
select the language which will be used for displaying menus and
indications.
Return
Setup
Time
Language
: English
AV Setup
Digital NR
: On
√
√
Miscellaneous
√
Move
Enter
18
Return
) button
) button to confirm your choice.
)
BN68-00630T-01Eng_1115
11/16/04
4:35 PM
Page 19
Storing Channels Automatically
ENG
You can scan for the frequency ranges available to you, (availability
depends on your country). Automatically allocated programme
numbers may not correspond to actual or desired programme
numbers. However you can sort numbers manually and clear any
channels you do not wish to watch.
1
TV
Press the MENU button.
Result:
Channel
Country
√
Manual Store
√
Edit
√
Fine Tune
√
Ch. Scan
√
The main menu is displayed.
Move
2
The options available in the Channel group are
displayed.
3
Press the ENTER (
4
Press the † or … button to select Country. Press the ENTER
(
) button.
Result:
6
7
Enter
TV
Channel
Country
: Austria
Austria
Auto Store
) button.
Belgium
Manual Store
Press the ENTER (
) button to confirm your choice
Press the † or … button to select Auto Store. Press the ENTER
(
) button.
Denmark
Fine Tune
Finland
Ch. Scan
France
†
Move
Enter
TV
Channel
Country
: Austria
9
√
Auto Store
√
Manual Store
√
Edit
√
Fine Tune
√
Ch. Scan
√
Move
➢
Return
The Auto Store menu is displayed.
Press the ENTER (
Result:
Croatia
Edit
The countries available are listed.
Select your country (or area) by pressing the † or … button.
➢ If you have selected the Others option but do not wish to
scan the PAL frequency range, store the channels manually
(see page 21).
Result:
8
Return
Press the † or … button to select Channel.
Result:
5
√
: Austria
Auto Store
Enter
) button to start the search.
The search will end automatically. Channels are sorted
and stored in an order which reflects their position in
the frequency range, (with lowest first and highest last).
The programme originally selected is then displayed.
To stop the search before it has finished, press the
MENU (
) button.
Auto Store
Channel store in process.
Storing.
57 MHz
1%
Stop
Enter
When the channels have been stored, you can:
◆ Sort them in the order required (see page 23)
◆ Clear a channel (see page 22)
◆ Fine-tune channel reception if necessary (see page 29)
◆ Assign a name to the stored channels (see page 24)
◆ Activate/deactivate the Digital Noise Reduction feature
(see page 36)
19
Return
Return
BN68-00630T-01Eng_1115
11/16/04
4:35 PM
Page 20
Storing Channels Manually
ENG
TV
You can store up to 100 television channels, including those
received via cable networks.
Channel
Country
√
: Austria
Auto Store
√
Manual Store
√
Edit
√
Fine Tune
√
Ch. Scan
√
Move
Enter
When storing channels manually, you can choose:
◆ Whether or not to store each of the channels found
◆ The programme number of each stored channel which
you wish to identify
Return
1
Result:
Manual Store
Prog.
Colour
System
Sound
System
9
Auto
BG
Channel
Search
Store
C --
245MHz
?
Adjust
Return
√ Move
Press the MENU button.
2
The main menu is displayed.
Press the † or … button to select Channel.
Result:
The options available in the Channel group are
displayed.
3
Press the ENTER (
4
Press the † or … button to select Manual Store.
Press the ENTER (
) button.
) button.
Manual Store
Prog.
Colour
System
9
Auto
BG
Channel
Search
Store
C --
245MHz
?
Adjust
Return
œ √ Move
Result:
Sound
System
5
The Manual Store menu is displayed.
If necessary, select the broadcasting standard required. Press the
œ or √ button to select Colour System and press the † or …
button. The colour standards are displayed in the following order.
(depending on the model).
Auto - PAL - SECAM or
Auto - NT3.58 - NT4.43 - PAL60
Manual Store
Prog.
Colour
System
Sound
System
9
Auto
BG
Channel
Search
Store
C 00
245MHz
?
Adjust
Return
œ √ Move
20
6
Press the œ or √ button to select Sound System and press the †
or … button. The sound standards are displayed in the following
order. (depending on the model).
BG - DK - I - L
BN68-00630T-01Eng_1115
11/16/04
4:35 PM
Page 21
Storing Channels Manually (continued)
ENG
7
If you know the number of the channel to be stored, see the
following steps.
◆ Press the œ or √ button to select Channel.
◆ Press the † or … button to select C (Air channel) or S (Cable
channel).
◆ Press the √ button.
◆ Press the numeric buttons (0~9) to select indicate the required
number.
no sound or abnormal sound, re-select the sound standard
➣ Ifrequired.
8
If you do not know the channel numbers, select the Search by
pressing the œ or √ button. Press the † or … button to start the
search.
Result:
The tuner scans the frequency range until the first
channel or the channel that you selected is received on
your screen.
Manual Store
Prog.
Colour
System
Sound
System
9
Auto
BG
Channel
Search
Store
C --
245MHz
?
Adjust
Return
œ √ Move
Manual Store
Prog.
Colour
System
Sound
System
9
Auto
BG
Channel
Search
Store
C 04
245MHz
?
Adjust
Return
œ √ Move
Manual Store
9
10
11
To assign a programme number to a channel, select the Prog. by
pressing the œ or √ button. Press the † or … button until you find
the correct number.
To store the channel and associated programme number, select
the Store by pressing the œ or √ button. Press the ENTER (
)
button.
Prog.
Colour
System
Sound
System
9
Auto
BG
Channel
Search
Store
C 04
245MHz
?
Adjust
Return
œ √ Move
Repeat Steps 7 to 10 for each channel to be stored.
Manual Store
Prog.
☛
Channel mode
◆ C (Real channel mode): You can select a channel by
entering the assigned number to each air broadcasting station
in this mode.
Colour
System
Sound
System
9
Auto
BG
Channel
Search
Store
C 15
245MHz
OK
œ √ Move
Enter
◆ S (Cable channel mode): You can select a channel by
entering the assigned number for each cable channel in this
mode.
21
Return
BN68-00630T-01Eng_1115
11/16/04
4:35 PM
Page 22
Skipping Unwanted Channels
ENG
◆ Skipping unwanted channels
TV
You can exclude the channels of your choice from the channel
scan operation. When you scan through the stored channels,
those that you have chosen to skip are thus not displayed. All
channels that you do not specifically choose to skip are
displayed during scanning.
Channel
Country
√
: Austria
Auto Store
√
Manual Store
√
Edit
√
Fine Tune
√
Ch. Scan
√
1
Move
Enter
TV
Return
Result:
2
Edit
Add/Delete
√
Sort
√
LNA
√
: Off
Press the † or … button to select Channel.
Result:
The options available in the Channel group are
displayed.
3
Press the ENTER (
4
Press the † or … button to select Edit. Press the ENTER (
button.
) button.
√
Child Lock
Move
Enter
TV
Return
Result:
5
Add/Delete
✽
✽
✽
✽
✽
---------------------
Move
Added
Deleted
Deleted
Deleted
Deleted
Enter
TV
Return
Add/Delete
Prog.
---------------------
Adjust
✽
✽
✽
✽
✽
Enter
22
Added
Deleted
Deleted
Deleted
Deleted
Return
)
The Edit menu is displayed.
Press the † or … button to select Add/Delete. Press the ENTER
(
) button.
Result:
Prog.
1
2
3
4
5
The main menu is displayed.
√
Name
1
2
3
4
5
Press the MENU button.
The Add/Delete menu is displayed with the current
channel automatically is selected.
6
Press the † or … button to select the channel to be deleted.
7
Press the ENTER (
8
To add or delete the channel, select Added or Deleted by
pressing the † or … button. Press the ENTER (
) button to
confirm.
) button.
BN68-00630T-01Eng_1115
11/16/04
4:35 PM
Page 23
Sorting the Stored Channels
ENG
This operation allows you to change the programme numbers of
stored channels. This operation may be necessary after using ATM.
You can delete those channels you do not want to keep.
1
4
7
√
Fine Tune
√
Ch. Scan
√
Enter
TV
)
Return
Edit
Add/Delete
√
Sort
√
√
Name
LNA
√
: Off
√
Child Lock
The Edit menu is displayed.
Press the † or … button to select Sort. Press the ENTER (
button.
)
Move
Enter
Return
The Sort menu is displayed.
Select the channel that you wish to move by pressing the † or …
button. Press the ENTER (
) button.
Prog.
2
3
4
5
6
The channel is moved to its new position and all other
channels are shifted accordingly.
Repeat Steps 6 to 7 until you have moved all the channels to the
required programme numbers.
Sort
TV
Select the number of the programme to which the channel is to be
moved by pressing the † or … button. Press the ENTER (
)
button.
Result:
8
√
Edit
Move
) button.
Press the † or … button to select Edit. Press the ENTER (
button.
Result:
6
√
Manual Store
The options available in the Channel group are
displayed.
Press the ENTER (
Result:
5
The main menu is displayed.
√
: Austria
Auto Store
Press the † or … button to select Channel.
Result:
3
Channel
Country
Press the MENU button.
Result:
2
TV
---------------------
✽
✽
✽
✽
✽
Move
Enter
TV
Return
Sort
Prog.
2
3
4
5
6
---------------------
Move
✽
✽
✽
✽
✽
----- ✽
Enter
23
Return
BN68-00630T-01Eng_1115
11/16/04
4:35 PM
Page 24
Assigning Names to Channels
ENG
TV
Channel
Country
√
: Austria
Auto Store
√
Manual Store
√
Edit
√
Fine Tune
√
Ch. Scan
√
Channel names will be assigned automatically when channel
information is broadcast. These names can be changed, allowing
you to assign new names.
1
Result:
2
Move
Enter
TV
Return
Edit
Add/Delete
√
Sort
√
Name
√
LNA
Press the ENTER (
4
Press the † or … button to select Edit. Press the ENTER (
button.
Result:
5
Enter
Return
Name
Prog.
2
3
4
5
6
Name
✽
✽
✽
✽
✽
---------------------
Move
Enter
TV
2
3
4
5
6
✽
✽
✽
✽
✽
Adjust
Enter
24
Return
The Edit menu is displayed.
)
The Name menu is displayed with the current channel
automatically is selected.
Arrow indications are displayed around the name box.
7
Press the † or … button to select a letter (A~Z), a number (0~9)
or a symbol (-, space). Move on the previous or next letter by
pressing the œ or √ button.
8
When you have finished entering the name, press the ENTER
(
) button to confirm the name.
Return
Name
---------------------
)
If necessary, select the channel to be assigned a new name by
pressing the † or … button. Press the ENTER (
) button.
Result:
Name
Prog.
6
) button.
Press the † or … button to select Name. Press the ENTER (
button.
Result:
TV
The options available in the Channel group are
displayed.
3
√
Move
The main menu is displayed.
Press the † or … button to select Channel.
Result:
√
: Off
Child Lock
Press the MENU button.
BN68-00630T-01Eng_1115
11/16/04
4:35 PM
Page 25
Activating the Child Lock
ENG
◆ Activating the child lock
This feature allows you to lock selected channels so that they
cannot be viewed. This can be used to prevent unauthorised
viewing of unsuitable programmes.
1
4
√
Manual Store
√
Edit
√
Fine Tune
√
Ch. Scan
√
Move
The options available in the Channel group are
displayed.
Press the ENTER (
Return
Edit
Add/Delete
√
Sort
√
√
Name
)
LNA
√
: Off
√
Child Lock
The Edit menu is displayed.
Press the † or … button to select Child Lock. Press the ENTER
(
) button.
Result:
Enter
TV
) button.
Press the † or … button to select Edit. Press the ENTER (
button.
Result:
5
The main menu is displayed.
√
: Austria
Auto Store
Press the † or … button to select Channel.
Result:
3
Channel
Country
Press the MENU button.
Result:
2
TV
The Child Lock menu is displayed with the current
channel automatically is selected.
Blue Screen is displayed when the Child Lock is
activated.
6
Press the † or … button to select the channel to be locked.
7
Press the ENTER ( ) button. To lock the channel, select
Locked by pressing the † or … button (to unlock the channel,
select Unlocked). Press the ENTER ( ) button to confirm.
Move
Enter
Return
Child Lock
TV
Prog.
2
3
4
5
6
✽
✽
✽
✽
✽
---------------------
Move
Unlocked
Unlocked
Unlocked
Unlocked
Unlocked
Enter
Return
Child Lock
TV
Prog.
2
3
4
5
6
---------------------
Adjust
✽
✽
✽
✽
✽
Enter
25
Unlocked
Unlocked
Locked
Unlocked
Unlocked
Return
BN68-00630T-01Eng_1115
11/16/04
4:35 PM
Page 26
Displaying Information
ENG
You can view the channel information and setting status you select
by pressing the “INFO (
)” button on the remote control.
Mono
P1 ✽
Picture
Sound
00 : 00
: Dynamic
: Music
Changing the Picture Standard
TV
You can select the type of picture which best corresponds to your
viewing requirements.
Picture
Mode
Custom
Colour Tone
Film Mode
Size
DNIe
PIP
Move
:
:
:
:
Normal
Off
16 : 9
On
Enter
TV
√
√
√
√
√
√
√
: Dynamic
1
Press the MENU button.
The main menu is displayed.
Result:
2
Press the † or … button to select Picture.
The options available in the Picture group are
Result:
displayed.
3
Press the ENTER (
) button.
The Mode is selected.
Result:
4
Press the ENTER (
) button again.
The options available are listed.
Result:
5
Select the option by pressing the † or … button.
The following modes are available depending on the
Result:
input source.
◆ Dynamic - Standard - Movie - Custom
◆ High - Middle - Low - Custom
(DVI Mode).
6
Press the ENTER (
Return
Picture
Mode
Custom
Colour Tone
Film Mode
Size
DNIe
PIP
Move
: Dynamic
Dynamic
:
:
:
:
Standard
Normal
Off Movie
16 :Custom
9
On
Enter
Return
➣
26
) button to confirm.
You can also set these options simply by pressing the
P.MODE (
: Picture Mode) button.
BN68-00630T-01Eng_1115
11/16/04
4:35 PM
Page 27
Adjusting the Picture Settings
ENG
Your television has several settings which allow you to control
picture quality.
1
The main menu is displayed.
Press the † or … button to select Picture.
Result:
The options available in the Picture group are
displayed.
Move
3
Press the ENTER (
4
Select the required option (Custom, Colour Tone) pressing the
† or … button.
5
Press the † or … button to select Custom.
Press the ENTER (
) button.
Result:
6
Picture
Mode
Custom
Colour Tone
Film Mode
Size
DNIe
PIP
Press the MENU button.
Result:
2
TV
) button.
:
:
:
:
Normal
Off
16 : 9
On
Enter
TV
√
√
√
√
√
√
√
: Dynamic
Return
Custom
Contrast
Brightness
Sharpness
Colour
Tint
G50
70
50
70
50
R50
The Custom menu is displayed.
Move
Press the ENTER (
) button to change the setting.
The options are displayed in the following order.
◆ Custom : Contrast, Brightness, Sharpness, Colour,
Tint(NTSC ONLY)
➣
horizontal bar is displayed. Move the horizontal bar’s
➣ The
cursor left or right by pressing the œ or √ button.
When the Picture Mode is set to Custom, the settings values
➣ may
vary depending on the input source.
Enter
Contrast
Return
70
Custom Options available in DVI Mode: Contrast,
Brightness, Sharpness.
(ex. RF, Video, Component or DVI)
you make any changes to these settings, the picture
➣ Ifstandard
is automatically switched to the Custom
When you are satisfied with the settings, press the EXIT (
button to return to normal viewing.
➣
Picture
Mode
Custom
Colour Tone
Film Mode
Size
DNIe
PIP
: Dynamic
:
:
:
:
Normal
Cool2
Off
16 : Cool1
9
On Normal
Warm1
Warm2
Move
◆ Colour Tone : Cool2, Cool1, Normal, Warm1, Warm2
7
TV
Enter
)
If you make any changes to these settings, the picture
standard is automatically switched to the Custom.
27
Return
BN68-00630T-01Eng_1115
11/16/04
4:35 PM
Page 28
Adjusting the Picture Settings (DVI Mode)
➢
ENG
1
TV
Preset to the DVI mode by using the TV/VIDEO button.(or SOURCE
button on the front of the PDP)
Press the MENU button.
Picture
Mode
Custom
Colour Tone
Film Mode
Size
DNIe
PIP
Move
: Middle
:
:
:
:
Custom
Off
16 : 9
On
Enter
TV
√
√
√
√
√
√
√
Result:
2
Press the † or … button to select Picture.
Result:
3
Press the ENTER (
4
Press the † or … button to select Custom. Press the ENTER
(
) button.
Result:
70
50
70
50
R50
5
Enter
The Custom menu is displayed.
)
The horizontal bar is displayed. Move the horizontal
bar’s cursor left or right by pressing the œ or √ button.
Return
6
28
) button.
Press the † or … button to select the option (Contrast,
Brightness, Sharpness) to be adjusted. Press the ENTER (
button.
Result:
Move
The options available in the Picture group are
displayed.
Return
Custom
Contrast
Brightness
Sharpness
Colour
Tint
G50
The main menu is displayed.
Press the MENU button to confirm your choice.
BN68-00630T-01Eng_1115
11/16/04
4:35 PM
Page 29
Using the Fine Tune
ENG
If reception is weak, you can fine tune a channel manually.
TV
1
Result:
2
The main menu is displayed.
Press the † or … button to select Channel.
Result:
The options available in the Channel group are
displayed.
3
Press the ENTER (
4
Press the † or … button to select Fine tune. Press the ENTER
(
) button.
Channel
Country
Press the MENU button.
√
: Austria
Auto Store
√
Manual Store
√
Edit
√
Fine Tune
√
Ch. Scan
√
Move
Enter
Return
) button.
Fine Tune
P1
0
Result:
5
The horizontal bar is displayed. Move the horizontal
bar’s cursor left or right by pressing the œ or √ button
to reach the required setting.
Reset
Move
Press the œ or √ button until the picture and sound are both clear
and sharp.
Return
œ √ Adjust
Store
Fine Tune
P1
➣
➣
➣
3
If you are unable to fine tune a channel, check that the
Colour System and Sound System settings are correct.
Reset
Move
Return
œ √ Adjust
Store
Fine tune Store will change the colour of the Channel
OSD(On Screen Display) from White to Red.
Fine Tune
To reset the fine tuning to “0”, press the † button to
select “Reset”, then press the ENTER button.
P 1 is fine tuned
3
Reset
Move
P1
Return
œ √ Adjust
C11
29
Store
BN68-00630T-01Eng_1115
11/16/04
4:36 PM
Page 30
Viewing the Channel Scan Picture
ENG
TV
1
Channel
Country
√
Manual Store
√
Edit
√
Fine Tune
√
Ch. Scan
√
Move
Enter
Result:
√
: Austria
Auto Store
Return
Press the MENU button.
2
The main menu is displayed.
Press the † or … button to select Channel.
Result:
The options available in the Channel group are
displayed.
3
Press the ENTER (
4
Press the † or … button to select Ch. Scan. Press the ENTER
(
) button.
) button.
Ch. Scan
Result:
You can view every memorized channel in order.
P1✽
Return
Freezing the Current Picture
You can freeze the picture when watching a television programme
simply by pressing the “STILL” button. To return to normal viewing,
press it again.
➣
➣
30
In the PIP mode, the main and sub pictures are stilled at
the same time.
This function will automatically cancel after 5 minutes.
BN68-00630T-01Eng_1115
11/16/04
4:36 PM
Page 31
Selecting the Picture Size
ENG
You can select the picture size which best corresponds to your
viewing requirements.
1
3
4
5
6
The main menu is displayed.
Press the † or … button to select Picture.
Result:
Picture
Mode
Custom
Colour Tone
Film Mode
Size
DNIe
PIP
Press the MENU button.
Result:
2
TV
The options available in the Picture group are
displayed.
Press the ENTER (
) button.
Move
Normal
Off
16 : 9
On
√
√
√
√
√
√
√
Return
Size
Press the † or … button until the Size is selected. Press the
ENTER (
) button
Press the † or … button to change the setting.
Zoom
◆ Auto Wide : Expanding and pulling up the picture from 4:3 to
16:9 ratio.
◆ 16:9
: Sets the picture to 16:9 wide mode.
◆ Panorama : Use this mode for the wide aspect ratio of a
panoramic picture.
◆ Zoom
: Magnify the size of the picture vertically on
screen.
◆ 14:9
: Magnify the size of the picture more than 4:3.
◆ 4:3
: Sets the picture to 4:3 normal mode.
4:3
) button to confirm.
:
:
:
:
Enter
TV
Auto Wide
Press the ENTER (
: Dynamic
16:9
Panorama
14:9
Move
Enter
Return
DVI Mode
TV
Size
Auto Wide
16:9
Panorama
Zoom
14:9
➣
4:3
◆ You can select these options by simply pressing the
P.SIZE button on the remote control.
Move
Enter
◆ The picture size can not be changed in the PIP mode.
◆ Depending on the input source, the P.SIZE options
may vary.
Positioning and Sizing the screen using Zoom
➣
◆ Resizing the screen using the Zoom enables the
positioning and sizing of the screen to up/down
direction using the † or … button as well as the
screen size.
◆ Move the screen up/down using the † or … button
after selecting the
by pressing the † or … button.
◆ Resize the screen vertically using the † or … button
after selecting the
by pressing the † or … button.
◆ Screen enlargement operates only in TV/Video/SVideo/Component input modes.
◆ DVI mode prevents the screen enlargement function.
31
Return
BN68-00630T-01Eng_1115
11/16/04
4:36 PM
Page 32
Selecting the Film Mode
ENG
TV
You can automatically sense and process film signals from some
sources and adjust the picture for optimum quality.
Picture
Mode
Custom
Colour Tone
Film Mode
Size
DNIe
PIP
Move
: Dynamic
:
:
:
:
Normal
Off
16 : 9
On
Enter
TV
√
√
√
√
√
√
√
Move
Press the MENU button.
The main menu is displayed.
Result:
2
Press the † or … button to select Picture.
The options available in the Picture group are displayed.
Result:
3
Press the ENTER (
4
Press the † or … button to select Film Mode. Press the ENTER
(
) button.
5
Press the † or … button to change the setting. (Off or On).
Return
Picture
Mode
Custom
Colour Tone
Film Mode
Size
DNIe
PIP
1
: Dynamic
:
:
:
:
Normal
Off Off
16 : 9On
On
Enter
) button.
◆ On : Automatically senses and processes film signals from
some sources and adjusts the picture for optimum quality.
◆ Off : Switches off the Film Mode.
➢
Return
◆ Not available in the DVI or Component (480p, 576p, 720p,
1080i) mode.
◆ Mode discrepancies, such as turning off Film Mode while
viewing a film source or turning on Film Mode while viewing
non-film sources, may affect the picture quality.
DNIeTM (Digital Natural Image engine)
TV
Picture
Mode
Custom
Colour Tone
Film Mode
Size
DNIe
PIP
Move
: Dynamic
:
:
:
:
Normal
Off
16 : 9
On
Enter
TV
√
√
√
√
√
√
√
Move
Press the MENU button.
Result:
2
The main menu is displayed.
Press the † or … button until the Picture is selected.
Result:
The options available in the Picture group are
displayed.
3
Press the ENTER (
4
Press the † or … button until the DNIe is selected. Press the
ENTER (
) button.
5
Press the † or … button to change the setting.
◆ On: Switches on the DNIe mode.
◆ Off: Switches off the DNIe mode.
◆ Demo (Option): The screen before applying DNIe appears on
the right and the screen after applying DNIe
appears on the left.
) button.
: Dynamic
:
:
:
:
Normal
Off
16 : 9On
On Off
Demo
Enter
32
1
Return
Picture
Mode
Custom
Colour Tone
Film Mode
Size
DNIe
PIP
This feature bring you more detailed image with 3D noise reduction, detail
enhancement, contrast enhancement and white enhancement. New image
compensation Algorithm gives brighter, clearer, much detailed image to you.
Return
BN68-00630T-01Eng_1115
11/16/04
4:36 PM
Page 33
Setting the Blue Screen
TV
Setup
√
Time
If no signal is being received or the signal is very weak, a blue screen automatically replaces the noisy picture background. If you wish to continue viewing the
poor picture, you must set the “Blue Screen“ mode to “Off“.
Language
: English
Digital NR
: On
Press the MENU button.
Result:
2
Press the ENTER (
4
Press the † or … button to select Miscellaneous. Press the
ENTER ( ) button.
6
: Off
Move
Enter
TV
√
√
Blue Screen
√
Return
Miscellaneous
Melody
: Off
Plug & Play
Press the † or … button to change the setting. (On or Off).
➣
: Off
Plug & Play
The options available in the Miscellaneous group are
displayed.
Return
Miscellaneous
Melody
) button.
Press the † or … button to select Blue Screen. Press the
ENTER (
) button.
Enter
TV
The options available in the Setup group are displayed.
3
Result:
Move
The main menu is displayed.
Press the † or … button to select Setup.
Result:
5
√
√
Miscellaneous
1
√
√
AV Setup
Blue Screen
: Off Off
On
◆ Blue Screen is displayed while no signal from the external
device in the External Mode, regardless of the Blue Screen
Setting.
Move
Enter
Return
Setting the Melody Sound
TV
Miscellaneous
Melody
A melody sounds when the television is powered on or off.
: Off
Blue Screen
1
Press the MENU button.
The main menu is displayed.
Result:
2
Press the † or … button to select Setup.
The options available in the Setup group are displayed.
Result:
3
4
Press the ENTER (
) button.
Press the † or … button to select Miscellaneous. Press the
ENTER (
) button.
Result:
: Off
Move
Enter
TV
√
√
Plug & Play
√
Return
Miscellaneous
Melody
Plug & Play
: Off Off
On
Blue Screen
: Off
The options available in the Miscellaneous group are
displayed.
5
Press the † or … button to select Melody.
Press the ENTER (
) button.
6
Press the † or … button to change the setting. (On or Off).
Move
Enter
33
Return
ENG
BN68-00630T-01Eng_1115
11/16/04
4:36 PM
Page 34
Viewing the Picture In Picture (PIP)
ENG
TV
You can display a sub picture within the main picture of TV
program or external A/V devices.
Picture
Mode
Custom
Colour Tone
Film Mode
Size
DNIe
PIP
Move
√
√
√
√
√
√
√
: Dynamic
:
:
:
:
Normal
Off
16 : 9
On
Enter
Press the MENU button.
The main menu is displayed.
Result:
2
Press the † or … button to select Picture.
The options available in the Picture group are
Result:
displayed.
3
Press the ENTER (
4
Press the † or … button to select PIP. Press the ENTER (
button.
Return
PIP
TV
1
PIP
Source
: On Off
: TV On
Swap
Size
Position
Prog.
:
:
: P8
Result:
Move
Enter
Return
PIP
Source
Swap
Size
Position
Prog.
6
Press the † or … button to select Source and press the ENTER
(
) button. Select a source of the sub picture by pressing the
ENTER (
) button.
TV - Ext.1 - Ext.2 - AV - S-Video Component - DVI
7
†
8
PIP
Source
Swap
Size
Position
Prog.
: On
: TV
:
:
: P8
Move
Enter
Press the † or … button to select Swap. Press the ENTER (
button.
√
√
√
√
√
)
The main picture and sub picture are interchanged.
Result:
Return
PIP
TV
The sources are displayed in the following order:
Result:
Ext.2
:
AV
:
S-Video
: P08
Component
Enter
The options available in the PIP group are displayed.
Press the ENTER (
) button, set the PIP to on by pressing the
† or … button. Press the ENTER (
) button.
: On TV
: TV Ext.1
Move
)
5
PIP
TV
) button.
Press the † or … button to select Size. Select a size of the sub
picture by pressing the ENTER (
) button.
Result:
The sizes are displayed in the following order:
(Large) - (Small) - (Double1) - (Double2)
➣
√
Select a size of the sub picture by pressing the
† or … button. Press the ENTER (
) button.
Return
Table of PIP Settings
X - This PIP combination is not available.
O - This PIP combination is available.
PIP
TV
PIP
Source
Swap
Size
Position
Prog.
: On
: TV
:
:
: P08
Move
Enter
34
Return
TV
Video
S-VHS
Comp576i
Comp480p~
DVI
TV
X
X
X
X
O
O
Video
X
X
X
X
O
O
S-VHS
X
X
X
X
O
O
Comp576i
X
X
X
X
X
X
Comp480p~
O
O
O
X
X
X
DVI
O
O
O
X
X
X
BN68-00630T-01Eng_1115
11/16/04
4:36 PM
Page 35
Viewing the Picture In Picture (PIP) (continued)
ENG
PIP
TV
PIP
Source
Swap
Size
Position
Prog.
Press the † or … button to select Position. Press the ENTER
(
) button.
9
Result:
The positions available are displayed.
-
a position of the sub picture by pressing the † or …
➣ Select
button. Press the ENTER (
) button.
10
Press the † or … button to select Prog.. Select the channel that
you want to view through sub picture by pressing the ENTER (
)
button.
➣
If the sub picture is no signal and the main picture is
output from a Component or DVI signal, the sub picture
will be blue. If the main picture is output from a Video
signal, the sub picture will be black.
: On
: TV
:
:
: P08
Move
Enter
Return
PIP
TV
PIP
: On
Source
Swap
Size
Position
Prog.
: TV
:
:
: P08 P 1
Move
Enter
35
Return
BN68-00630T-01Eng_1115
11/16/04
4:36 PM
Page 36
Using the Digital NR (Digital Noise Reduction) Feature
ENG
TV
Setup
√
Time
Language
: English
√
If the signal received by your television is weak, you can activate
this feature to help reduce any static and ghosting that may appear
on the screen.
√
AV Setup
Digital NR
√
: On
√
Miscellaneous
Move
Enter
TV
Return
1
Press the MENU button.
The main menu is displayed.
Result:
2
Press the ▼ or ▲ button until the Setup is selected.
The options available in the Setup group are displayed.
Result:
3
Press the ENTER (
4
Press the ▼ or ▲ button until the Digital NR is selected.
Press the ENTER (
) button.
5
Select Off or On by pressing the ▼ or ▲ button. Press the
ENTER (
) button to confirm.
Setup
Time
Language
) button.
: English
AV Setup
Digital NR
: On Off
Miscellaneous
Move
On
Enter
Return
Using the LNA (Low Noise Amplifier) Feature
TV
Channel
Country
: Austria
√
Auto Store
√
Manual Store
√
Edit
√
Fine Tune
√
Ch. Scan
√
Move
Enter
Return
This function is very useful in the situation that the TV is used in
weak signal. LNA amplifies the TV signal in the weak signal area,
but not noise.
1
Press the MENU button.
Result:
2
Press the † or … button to select Channel.
Result:
TV
Edit
Add/Delete
√
Sort
√
Name
√
LNA
√
: Off
Press the ENTER (
4
Press the † or … button to select Edit.
) button.
Press the ENTER (
Result:
Move
Enter
TV
Return
5
Edit
6
Name
LNA
: Off Off
Child Lock
On
Move
Enter
➢
Return
) button.
The Edit menu is displayed.
Press the † or … button to select LNA.
) button.
Press the ENTER (
Result:
Add/Delete
Sort
The options available in the Channel group are
displayed.
3
√
Child Lock
The main menu is displayed.
The options available are listed.
Select On or Off by pressing the † or … button.
) button to confirm.
Press the ENTER (
◆ If the picture is noisy with the LNA set to On, select Off.
◆ LNA setting is to be made for each channel.
◆ Depending on areas, factory mode of LNA will be set up
as On or Off.
36
BN68-00630T-01Eng_1115
11/16/04
4:36 PM
Page 37
Changing the Sound Standard
ENG
You can select the type of special sound effect to be used when
watching a given broadcast.
TV
Sound
Mode
1
2
√
Equalizer
Press the MENU button.
Result:
The main menu is displayed.
Auto Volume
: Off
√
SRS TSXT
: Off
√
Internal Mute
: Off
√
Press the † or … button to select Sound.
Result:
The options available in the Sound group are displayed.
Move
3
Press the ENTER (
Result:
4
5
√
: Standard
Return
) button.
The Mode is selected.
Press the ENTER (
Enter
) button agin.
Select the option by pressing the † or … button. The sound
effects are displayed in the following order.
TV
Sound
Mode
: Standard
Standard
Equalizer
Music
Auto Volume
: Off
SRS TSXT
: Off
Internal Mute
: Off
Custom
Movie
Speech
Standard - Music - Movie - Speech - Custom.
6
Press the ENTER (
➣
) button to confirm.
Move
Enter
You can also set these options simply by pressing the
S.MODE (
: Sound Mode) button.
37
Return
BN68-00630T-01Eng_1115
11/16/04
4:36 PM
Page 38
Adjusting the Sound Settings
ENG
The sound settings can be adjusted to suit your personal preferences.
TV
Sound
Mode
√
: Standard
1
Press the MENU button.
The main menu is displayed.
Result:
2
Press the † or … button to select Sound.
The options available in the Sound group are displayed.
Result:
3
Press the ENTER (
4
Press the † or … button to select Equalizer. Press the ENTER
(
) button.
The Equalizer menu is displayed with the current
Result:
option.
5
Select the option (volume, balance, equalizer) to be adjusted by
pressing the œ or √ button. Press the † or … button to reach the
required setting.
6
When you are satisfied with the settings, press the MENU (
button to store them.
√
Equalizer
Auto Volume
: Off
√
SRS TSXT
: Off
√
Internal Mute
: Off
√
Move
Enter
Equalizer
TV
) button.
Return
0
R
L
100 300 1K 3K 10K
√ Move
Adjust
Return
➣
)
If you make any changes to the equalizer settings, the
sound standard is automatically switched to the Custom.
Adjusting the Volume Automatically
Sound
Mode
: Standard
√
√
Equalizer
Auto Volume
: Off
√
SRS TSXT
: Off
√
Internal Mute
: Off
√
Move
Enter
TV
Each broadcasting station has its own signal conditions, and so it
is not easy for you to adjust the volume every time the channel is
changed. This feature lets you automatically adjust the volume of
the desired channel by lowering the sound output when the
modulation signal is high or by raising the sound output when the
modulation signal is low.
1
Press the MENU button.
The main menu is displayed.
Result:
2
Press the † or … button to select Sound.
The options available in the Sound group are displayed.
Result:
3
Press the ENTER (
4
Press the † or … button to select Auto Volume. Press the
ENTER (
) button.
5
Select the option (Off or On) by pressing the † or … button.
Return
Sound
Mode
: Standard
Equalizer
Auto Volume
SRS TSXT
: Off Off
: Off On
Internal Mute
: Off
Move
Enter
38
Return
) button.
BN68-00630T-01Eng_1115
11/16/04
4:36 PM
Page 39
Setting the TruSurround XT
ENG
TruSurround XT is a patented SRS technology that solves the
problem of playing 5.1 multichannel content over two speakers.
Trusurround delivers a compelling, virtual surround sound
experience through any two-speaker playback system, including
internal television speakers. It is fully compatible with all
multichannel formats.
1
TV
Sound
Mode
: Standard
Auto Volume
: Off
√
SRS TSXT
: Off
√
Internal Mute
: Off
√
Press the MENU button.
Result:
The main menu is displayed.
Move
2
Enter
Return
Press the † or … button until the Sound is selected.
Result:
The options available in the Sound group are displayed.
TV
Sound
Mode
3
Press the ENTER (
4
Press the † or … button until the SRS TSXT is selected. Press the
ENTER (
) button.
5
√
√
Equalizer
) button.
Equalizer
Auto Volume
: Off
SRS TSXT
: Off
Internal Mute
Off
: Off
3D Mono
Stereo
Press the † or … button to change the setting. (Off, 3D Mono or
Stereo).
➢
: Standard
Move
Enter
Return
TruSurround XT, SRS and (
) Symbol
are trademarks of SRS Labs, Inc.
TruSurround XT technology is
incorporated under license from SRS
Labs, Inc.
Selecting the Internal Mute
If you want to hear the sound through separate speakers, cancel the
internal amplifier.
TV
Sound
Mode
: Standard
1
Press the MENU button.
Result:
2
4
5
Auto Volume
: Off
√
SRS TSXT
: Off
√
Internal Mute
: Off
√
Press the † or … button to select Sound.
Result:
3
The main menu is displayed.
√
√
Equalizer
The options available in the Sound group are displayed.
Press the ENTER (
) button.
Press the † or … button to select Internal Mute. Press the
ENTER (
) button.
Press the † or … button to change the setting. (On or Off).
Move
Enter
TV
Return
Sound
Mode
: Standard
Equalizer
Auto Volume
: Off
SRS TSXT
: Off
Internal Mute
: Off Off
On
Move
Enter
39
Return
BN68-00630T-01Eng_1115
11/16/04
4:36 PM
Page 40
Selecting the Sound Mode (depending on the model)
ENG
The “DUAL I-II” button displays/controls the processing and output
of the audio signal. When power is switched on, the mode is
automatically preset to either “Dual-I ” or “Stereo”, depending on
the current transmission.
NICAM
Stereo
Type of broadcast
On-screen indication
Regular broadcast
(Standard audio)
Mono (Normal use)
Regular +
NICAM Mono
NICAM Mono ↔ Mono
NICAM Stereo
A2
Stereo
NICAM Dual-I/II
NICAM Dual-I →
NICAM Dual-II →
Mono
Regular broadcast
(Standard audio)
Mono
Bilingual or Dual-I/II
Dual-I ↔ Dual-II
Stereo
➣
NICAM Stereo ↔ Mono
(Forced mono)
Stereo ↔ Mono
(Forced mono)
◆ If the receiving conditions deteriorate, listening will be
easier if the mode is set to the Mono.
◆ If the stereo signal is weak and an automatic switching
occurs, then switch to the Mono.
◆ When receiving a mono sound in the AV mode, connect
to the “AUDIO-L” input connector on the side of the
television. If the mono sound comes out only from left
speaker, press the Dual I-II button.
40
BN68-00630T-01Eng_1115
11/16/04
4:36 PM
Page 41
Setting the Sleep Timer
ENG
You can select a time period of between 30 and 180 minutes after
which the television automatically switches to Standby mode.
1
Setup
√
Time
Press the MENU button.
Result:
2
TV
Language
The main menu is displayed.
Digital NR
3
Press the ENTER (
4
Press the † or … button to select Time. Press the ENTER (
button.
Move
5
√
Enter
Return
) button.
TV
Result:
√
: On
Miscellaneous
The options available in the Setup group are
displayed.
√
√
AV Setup
Press the † or … button to select Setup.
Result:
: English
)
The options available in the Time group are displayed.
Time
Clock
07 : 05
√
Sleep Timer
Off
√
On Timer
Off
√
Off Timer
Off
√
Press the † or … button to select Sleep Timer. Press the
ENTER (
) button.
Result:
The Sleep Timer menu is displayed with the Min is
selected.
6
Select the preset time intervals (Off, 30, 60, 90, 120, 150, 180) by
pressing the † or … button.
Press the œ or √ button to move to the Activation.
7
When you are satisfied with the settings, select Activation to
Yes or No by pressing the † or … button.
8
Press the ENTER (
Move
Enter
TV
Sleep Timer
Min
Activation
--
No
) button to confirm your selection.
√ Move
Adjust
➣
Return
◆ You can also set these options simply by pressing the
SLEEP button.
◆ If the sleep timer is not yet set, Off is displayed.
If the sleep timer is already set, the remaining time
before which the television switches to Standby mode
is displayed.
TV
Return
Sleep Timer
Min
Activation
30
Yes
œ √ Move
Adjust
Off
41
Return
BN68-00630T-01Eng_1115
11/16/04
4:36 PM
Page 42
Setting and Displaying the Current Time
ENG
TV
Setup
√
Time
Language
: English
You can set the television’s clock so that the current time is displayed
by pressing the “INFO (
)” button. You must also set the time if
you wish to use the automatic on or off timers.
➣
√
√
AV Setup
Digital NR
√
: On
√
Miscellaneous
Move
Enter
TV
1
Press the MENU button.
The main menu is displayed.
Result:
2
Press the ▼ or ▲ button to select Setup.
The options available in the Setup group are
Result:
displayed.
3
Press the ENTER (
4
Press the ▼ or ▲ button to select Time. Press the ENTER (
)
button.
The options available in the Time group are displayed
Result:
with Clock is selected.
5
Press the ENTER (
6
Press the ¦ or ‹button to move to the hour or minute.
Set the hour or minute by pressing the ▼ or ▲ button.
7
When you have finished, press the EXIT (
8
Press the INFO (
Return
Time
Clock
07 : 05
√
Sleep Timer
Off
√
On Timer
Off
√
Off Timer
Off
√
Move
Enter
TV
Return
Clock
Hour
Min
07
05
√ Move
Adjust
42
When pressing the “I / ” button (On/Off) on the front of
the television, the clock setting will be reset.
Return
) button.
) button.
) button to exit.
) button to display the current time.
BN68-00630T-01Eng_1115
11/16/04
4:36 PM
Page 43
Switching the Television On and Off Automatically
ENG
You can set the television’s clock and set the On or Off timers so that
the television will:
◆ Switch on automatically and tune to the channel of your
choice at the time you select
TV
√
Language
◆ Switch off automatically at the time you select
➣
Setup
Time
√
AV Setup
Digital NR
The first step is to set the television’s clock (refer to
“Setting and Displaying the Current Time” on the
previous page).
Press the MENU button.
The main menu is displayed.
Result:
√
Miscellaneous
3
Press the ENTER (
4
Press the † or … button to select Time. Press the ENTER (
)
button.
Result:
The options available in the Time group are displayed.
5
Press the ▼ or ▲ button to select On Timer. Press the ENTER
(
) button.
Result:
The options available in the On Timer group are
displayed.
7
When you are satisfied with the settings, select Activation to
Yes or No by pressing the † or … button.
8
Return
Time
Clock
07 : 05
√
Sleep Timer
Off
√
On Timer
Off
√
Off Timer
Off
√
) button.
Move
Press the MENU button.
The options available in the Time group are displayed
Result:
again.
Enter
TV
Select the Hour, Min, Prog., Volume by pressing the œ or √
button.
Set these by pressing the † or … button.
6
Enter
TV
Press the ▼ or ▲ button to select Setup.
The options available in the Setup group are
Result:
displayed.
2
√
: On
Move
1
√
: English
Return
On Timer
Hour
Min
Prog.
12
00
1
Volume
Activation
10
No
√ Move
Adjust
TV
Return
Off Timer
Hour
Min
12
00
Activation
9
Press the † or … button to select Off Timer. Press the ENTER
(
) button.
The Off Timer menu is displayed.
Result:
10
Select the Hour, Min or Activation by pressing the œ or √
button.
Set these by pressing the † or … button.
No
√ Move
Adjust
➣
Absent Power Off
When you set the timer “On”, your television will
eventually be turned off, if you do not operate any controls
during the 3 hours after the TV is turned on by timer.
This function is available in only the timer “On” mode and
will prevent a leakage accident or overheating, caused by
your TV left on for a long time due to the timer “On”
(when you are away on holiday, for example).
43
Return
BN68-00630T-01Eng_1115
11/16/04
4:36 PM
Page 44
Viewing an External Signal Source
ENG
TV
Input
Source List
√
: TV
Use the remote control to switch between viewing signal from
connected equipment, such as VCR, DVD, Set-Top-boxs and the TV
source (broadcast or cable)
√
Edit Name
1
Press the MENU button.
Result:
Press the ▼ or ▲ button to select Input .
2
Move
Enter
TV
Return
Source List
TV
Ext.1
Ext.2
AV
S-Video
Component
DVI
Move
-------------------
Enter
TV
Result:
Press the ENTER (
4
Press the ▼ or ▲ button to select Source List.
Press the ENTER (
) button.
➢
√
: TV
) button.
The options available in the Source List group are
displayed.
Press the ▼ or ▲ button to select signal source, then press the
ENTER (
) button.
5
Input
Source List
The options available in the Input group are
displayed.
3
Result:
Return
The main menu is displayed.
When you connect equipment to the TV, you can choose
between the following sets of jacks : Ext.1, Ext.2, AV,
S-Video, Component or DVI on the TV’s rear panel.
√
Edit Name
Move
Enter
TV
:
:
:
:
:
:
----
7
Press the ▼ or ▲ button to select Edit Name . Press the ENTER
(
) button.
Result:
The options available in the Edit Name group are
displayed.
8
Press the ▼ or ▲ button to select external device :
Ext.1 - Ext.2 - AV - S-Video - Component - DVI
DVD
9
Press the ENTER (
) button.
The Edit Name available are listed.
Result:
10
Select the name by pressing the † or … button.
Press the ENTER (
) button.
11
Set other signal sources (VCR, DVD, Cable STB, HD STB,
Satellite STB, AV Receiver, DVD Receiver, Game,
Camcorder, DVD Combo or DHR) using the same method as listed
above.
Cable STB
HD STB
†
Enter
Return
➣
➣
44
) button
VCR
Satellite STB
Move
Press the MENU button again, press the ENTER (
to select Input.
Return
Edit Name
Ext.1
Ext.2
AV
S-Video
Component
DVI
6
You can also set these options simply by pressing the
TV/VIDEO (
) button. If you change the external source
while viewing, pictures might take a short period of time to
be switched.
DHR : DVD HDD Recorder
BN68-00630T-01Eng_1115
11/16/04
4:36 PM
Page 45
Redirecting an Input to the External Output
ENG
Your television enables you to choose which audio/video signals
are output to the external connector.
TV
Setup
√
Time
1
Language
Press the MENU button.
Result:
√
: English
√
AV Setup
The main menu is displayed.
Digital NR
√
: On
√
Miscellaneous
2
Press the † or … button to select Setup.
Result:
The options available in the Setup group are
displayed.
3
Press the ENTER (
4
Press the † or … button to select AV Setup. Press the ENTER
(
) button.
Move
Enter
) button.
TV
Result:
5
6
Return
AV Setup
Ext.1
: TV
√
Ext.2
: TV
√
The AV Setup menu is displayed.
Press the † or … button to select required input (Ext.2), then
press the ENTER (
) button. Select the source to be directed
to the output by pressing the † or … button.
Press the ENTER (
Move
Enter
Return
) button to confirm the change.
TV
AV Setup
Ext.1
: TV
TV
Ext.2
: TV
Ext.1
Ext.2
AV
S-Video
Monitor Out
Move
Enter
45
Return
BN68-00630T-01Eng_1115
11/16/04
4:36 PM
Page 46
Teletext Feature
ENG
Most television channels provide written information services via
teletext. Information provided includes:
◆ Television programme times
◆ News bulletins and weather forecasts
◆ Sports results
◆ Travel information
This information is divided into numbered pages (see diagram).
Part
Contents
A
Selected page number.
B
Broadcasting channel identity.
C
Current page number or search indications.
D
Date and time.
E
Text.
F
Status information.
FASTEXT information.
➣
Teletext information is often divided between several
pages displayed in sequence, which can be accessed by:
◆ Entering the page number
◆ Selecting a title in a list
◆ Selecting a coloured heading (FASTEXT system)
46
BN68-00630T-01Eng_1115
11/16/04
4:36 PM
Page 47
Displaying the Teletext Information
ENG
You can display Teletext information at any time on your television
Teletext information to be displayed correctly,
☛ For
channel reception must be stable; otherwise:
◆ Information may be missing
◆ Some pages may not be displayed
1
2
Select the channel providing the Teletext service by pressing the
P
or
button.
Press the TTX/MIX (
Result:
) button to activate the teletext mode.
The contents page is displayed. It can be redisplayed
at any time by pressing the
(index) button.
3
Press the TTX/MIX (
) button again.
The screen will be split into two. This Double Teletext
Result:
feature lets you view the actual broadcast and teletext
information separately on the screen.
4
If you wish to display the actual broadcast and teletext information
on a single screen, press the TTX/MIX (
) button again.
5
To exit from the teletext display, press the EXIT (
) button.
47
BN68-00630T-01Eng_1115
11/16/04
4:36 PM
Page 48
Selecting Display Options
ENG
When you have displayed a Teletext page, you can select various
options to suit your requirements.
To display...
48
Press the...
◆ Hidden text
(answers to quiz games, for example)
(reveal)
◆ The normal screen
(reveal) again
◆ A secondary page by entering its number
(sub-page)
◆ The broadcast when searching for a page
(cancel)
◆ The next page
(page up)
◆ The previous page
(page down)
◆ Double-size letters in the:
• Upper half of the screen
• Lower half of the screen
(size)
• Once
• Twice
◆ The normal screen
• Three times
BN68-00630T-01Eng_1115
11/16/04
4:36 PM
Page 49
Selecting a Teletext Page
ENG
You can enter the page number directly by pressing the numeric
buttons on the remote control.
1
Enter the three-digit page number given in the content by
pressing the corresponding numeric buttons.
Result:
The current page counter is incremented and the
page is then displayed. If the selected page is linked
with several secondary pages, the secondary pages
are displayed in sequence. To freeze the display on a
given page, press the
(hold). Press it again to
resume.
2
If the FASTEXT system is used by the broadcasting company,
the different topics covered on a Teletext page are colour-coded
and can be selected by pressing the coloured buttons on the
remote control.
Press the coloured button corresponding to the topic that you wish
to select; the available topics are given on the status line.
Result:
The page is displayed with other coloured information
that can be selected in the same way.
3
To display the previous or next page, press the corresponding
P
or
button.
4
To display the subpage, see the following steps.
◆ Press the
(sub-page) button.
Result:
The available subpages appear.
◆ Select the required sub-page. Sub-pages can be scrolled by
pressing the
or
button.
5
When you have finished, press the EXIT (
your normal broadcast.
) button to return to
49
BN68-00630T-01Eng_1115
11/16/04
4:36 PM
Page 50
Connecting to the External Devices
ENG
“MONITOR OUT” are used for the equipment with an RGB output, such as
video game devices or video disc players.
Rear of the TV
①
(Input/Output)
VCR
②
DVD
or
Decoder /
Video game device
Video disc player
Satellite receiver
③
① This end can be fitted with:
◆ A SCART connector
◆ Three RCA connectors (VIDEO + AUDIO-L/R)
Input/Output Specification
Input
Connector
Output
Video
Audio (L/R)
S-Video
RGB
Video + Audio (L/R)
Ext.1
✔
✔
✔
✔
Only TV output is available.
Ext.2
✔
✔
✔
Output you can choose.
Rear of the TV
(Input/Output)
Camcorder
Video disc player
Video game device
50
BN68-00630T-01Eng_1115
11/16/04
4:36 PM
Page 51
Connecting to the S-Video Input
ENG
The S-VIDEO and RCA (AUDIO-L/R) connectors are used for equipment with an S-Video output,
such as a camcorder or VCR.
Rear of the TV
①
Camcorder
and
VCR
① To play picture and sound, both the S-VIDEO and RCA connectors must be used.
☛
Whenever you connect an audio or video system to your television,
ensure that all elements are switched off. Refer to the documentation
supplied with your equipment for detailed connection instructions
and associated safety precautions.
51
BN68-00630T-02Eng_0104
1/5/05
8:38 AM
Page 52
Connecting to the DVI Input
ENG
The “DVI” (video) and “L-AUDIO-R” connectors are used for equipment with a DVI output.
(Not Compatible with PC)
Rear of the TV
Satellite receiver
and
DVD
52
BN68-00630T-01Eng_1115
11/16/04
4:36 PM
Page 53
Connecting to the Component Input
ENG
Rear of the TV
DTV receiver
DVD
or
① The “COMPONENT” connectors are
used for DTV receiver or DVD.
(480i,p/576i,p/720p/1080i)
53
BN68-00630T-01Eng_1115
11/16/04
4:36 PM
Page 54
Connecting and Using the Home Theater System
ENG
Use the Monitor Out ports of the PDP for Home Theater System Connections.
Rear of the TV
Connecting the Home Theater System
① Connect the monitoring audio out L, and
R jacks of the MONITOR OUT on the
rear-side connection panel of the PDP
TV to the AUDIO IN jacks of the DVD
Home Theater System (or AV Receiver)
using the audio cable.
② Press the TV/VIDEO button to select the
desired external device connected to the
PDP TV.
③ If you want to hear the sound through
separate speakers, cancel the internal
amplifier.
②
①
DVD Home Theater
☛
AV Receiver Amplifier
◆ Refer to corresponding user’s manual from the manufacturer for wiring the
speakers to the DVD Home Theater System (or AV Receiver).
◆ Disable the PDP TV internal speaker to enjoy the rich sound through the
speakers of your Home Theater System.
◆ In this case, enjoy the sound from the Home Theater System while the PDP TV
does not produce the audio.
To Display the DVD Home Theater
! Turn the PDP on and press the TV/VIDEO button to select the Ext.1 (or Ext.2).
@ Be sure to connect the video cable properly if desired external input (Ext.1 or Ext.2) cannot be
selected.
# Play the DVD after activating the DVD Home Theater System.
$ Use the volume control of the Home Theater System while watching the PDP using the DVD
Home Theater, where the PDP TV does not produce the audio.
54
BN68-00630T-01Eng_1115
11/16/04
4:36 PM
Page 55
Pin Configurations
ENG
SCART Connector (Ext.1,Ext.2)
➢
Pins 5, 7, 9, 11, 13, 15 and 16 are used for RGB processing and are
only wired on the Ext.1 connector.
Pin
1
2
3
4
5
6
7
8
9
10
11
Signal
Audio output R
Audio input R
Audio output L
Audio chassis return
Video chassis return (RGB blue)
Audio input L
RGB blue input (EXT1)
Switching voltage
Video chassis return (RGB green)
AV-Link (EXT1)
RGB green input (EXT1)
Pin
12
13
14
15
16
17
18
19
20
21
Signal
Video chassis return (RGB red)
RGB red (EXT1) or chroma input
Blanking signal (RGB switching)
Video chassis return
Blanking signal ground
Video output
Video or Luminance input
Screening/chassis return
DVI Input Connector
(24Pin)
Pin
Signal
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
T.M.D.S. Data2T.M.D.S. Data2+
T.M.D.S. Data2/4 Shield
T.M.D.S. Data4T.M.D.S. Data4+
Clock (DDC)
Data (DDC)
Not Connected
T.M.D.S. Data1T.M.D.S. Data1+
T.M.D.S. Data1/3 Shield
T.M.D.S. Data3T.M.D.S. Data3+
+5V Power
5V Grounding
Hot Plug Detect
T.M.D.S. Data0T.M.D.S. Data0+
T.M.D.S. Data0/5 Shield
T.M.D.S. Data5T.M.D.S. Data5+
T.M.D.S. Clock Shield
T.M.D.S. Clock+
T.M.D.S. Clock-
55
BN68-00630T-01Eng_1115
11/16/04
4:36 PM
Page 56
Troubleshooting: Before Contacting Service Personnel
ENG
Before contacting Samsung after-sales service, perform the following simple checks.
If you cannot solve the problem using the instructions below, note the model and serial number of the
television and contact your local dealer.
No sound or picture
◆ Check that the mains lead has been connected to a wall socket.
◆ Check that you have pressed the “ I ” button (On/Off) and the
POWER ( ) button.
◆ Check the picture contrast and brightness settings.
◆ Check the volume.
Normal picture but no sound
◆ Check the volume.
◆ Check whether the volume MUTE (
has been pressed.
) button on the remote control
No picture or black and white picture
◆ Adjust the colour settings.
◆ Check that the broadcast system selected is correct.
Sound and picture interference
◆ Try to identify the electrical appliance that is affecting the television,
then move it further away.
◆ Plug your television into a different mains socket.
Blurred or snowy picture,
distorted sound
◆ Check the direction, location and connections of your aerial.
This interference often occurs due to the use of an indoor aerial.
Remote control malfunctions
◆ Replace the remote control batteries.
◆ Clean the upper edge of the remote control (transmission window).
◆ Check the battery terminals.
56
BN68-00630T-01Eng_1115
11/16/04
4:36 PM
Page 57
Memo
ENG
57
BN68-00630T-02Eng_0104
1/5/05
8:38 AM
Page 58
- AFTER SALES SERVICE
- Do not hesitate to contact your retailer or service agent
if a change in the performance of your product indicates
that a faulty condition may be present.
ELECTRONICS
BN68-00630T-02
Download PDF

advertising