Samsung | PS-63P76FD | Samsung PS63P76FD Benutzerhandbuch

PDP-TELEVISION
(PLASMA DISPLAY PANEL)
Owner’s Instructions
Before operating the unit,
please read this manual thoroughly,
and retain it for future reference.
ON-SCREEN MENUS
Picture In Picture (PIP)
Energy Saving
TELETEXT (Option)
SRS TruSurround XT
Digital Natural Image engine
Register your product at www.samsung.com/global/register
Record your Model and Serial number here for future reference.
BN68-01352B-01
BN68-01352B_¼­±¸_Cover.indd 1
▪ Model _______________ ▪ Serial No. _______________
2007-10-06 ¿ÀÈÄ 6:20:37
User Instructions
 Screen Image retention
Do not display a still image (such as on a video game or when hooking up a PC to this PDP) on the
plasma monitor panel for more than 2 hours as it can cause screen image retention. This image
retention is also known as “screen burn”. To avoid such image retention, reduce the degree of
brightness and contrast of the screen when displaying a still image.
 Height
The PDP can normally operate only under 2000m in height. It might abnormally function at a place
over 2000m in height so do not install and operate there.
 Heat on the top of the PDP TV
The top side of the product may be hot after long period of use as heat dissipates from the panel
through the vent hole in the upper part of the product. This is normal and does not indicate any defect
or operation failure of the product. However, children should be prevented from touching the upper
part of the product.
 The product is making a ‘cracking’ noise.
A ‘cracking’ noise may occur when the product contracts or expands due to a change of surrounding
environment such as temperature or humidity. This is normal and not a defect of the unit.
 Cell Defects
The PDP uses a panel consisting of 1,230,000(SD-level) to 3,150,000(HD-level) pixels which require
sophisticated technology to produce. However, there may be few bright or dark pixels on the screen.
These pixels will have no impact on the performance of the product.
 Avoid operating the TV at temperatures below 5°C(41°F)
 A still image displayed too long may cause permanent damage to the PDP Panel.
Watching the PDP TV in 4:3 format for a long period of time may leave traces
of borders displayed on the left, right and centre of the screen caused by the
difference of light emission on the screen. Playing a DVD or a game console
may cause similar effect to the screen. Damages caused by the above effect are
not covered by the Warranty.
 Afterimage on the Screen.
Displaying still images from Video games and PC for longer than a certain period of time may
produce partial afterimages. To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when
displaying still images.
 Warranty
- Warranty does not cover any damage caused by image retention.
- Burn-in is not covered by the warranty.
 Installation
Be sure to contact an authorized service centre, when installing your set in a location with heavy
dust, high or low temperatures, high humidity, chemical substance and where it operates continually
such as the airport, the train station etc. Failure to do so may cause a serious damage to your set.
Any functions related to Digital TV (DVB) will only work in countries or areas where DVB-T (MPEG2)
digital terrestrial signals are broadcasted. Please confirm with your local dealer if you can receive
DVB-T signals. Although this TV set follows the DVB-T specification, maintaining compatibility with
the future coming DVB-T digital terrestrial broadcasts is not guaranteed. Several functions may not be
available in some countries.
© 2007 Samsung Electronics Co., Ltd. All rights reserved.
English - 2
BN68-01352A-01Eng.indd 2
2007-10-06 ¿ÀÈÄ 5:49:44
Contents
Function Description
General Information






User Instructions ............................................. 2
Checking Parts................................................ 4
Using the Stand-Base ..................................... 4
Control Panel ................................................. 5
Connection Panel............................................ 6
Viewing the Remote Control .......................... 8
Operation





Switching Your Television On and Off ............. 9
Viewing the Menus ........................................ 10
Plug & Play Feature ...................................... 10
Viewing External Signal Sources .................. 12
Editing Device Names................................... 13
Channel Control







Storing Channels Automatically .................... 13
Storing Channels Manually ........................... 14
Adding / Locking Channels ........................... 15
Sorting the Stored Channels ......................... 16
Assigning Names to Channels ...................... 16
Fine Tuning Channel Reception.................... 17
LNA (Low Noise Amplifier) ............................ 17
PC Display
 Setting up Your PC Software (Based on
Windows XP) ................................................ 30
 Display Modes .............................................. 31
 Setting the PC ............................................... 32
 Setting the Home Theatre PC ....................... 33
Using the DTV Feature
 Previewing the DTV Menu System ............... 34
 Displaying Programme Information............... 35
 Operating the DTV Menu .............................. 36
About Anynet+
Picture Control







 Time Features ............................................... 24
 Language / Blue Screen / Melody /
Light Effect / Energy Saving /
HDMI Black Level ......................................... 25
 Using the Game Mode .................................. 26
 Wall- mount adjustment (Sold separately)
(PS-50P96FD) .............................................. 27
 Viewing the Picture in Picture (PIP) .............. 28
 Screen Burn Protection ................................. 29
Changing the Picture Standard ..................... 18
Customizing the Picture Settings .................. 18
Configuring Detailed Settings on the Picture .. 19
Selecting the Picture Size ............................. 20
Selecting the Screen Mode ........................... 20
Digital NR / Active Colour / DNIe / Movie Plus .. 21
Freezing the Current Picture ......................... 21
What is Anynet+? ........................................ 46
Connecting Anynet+ Devices ........................ 46
Setting Up Anynet+ ....................................... 47
Scanning and Switching between Anynet+
Devices ......................................................... 47
 Recording...................................................... 48
 Listening through a Receiver ........................ 49
 Check Points before Requesting Service ..... 49




Sound Control
Appendix
 Sound Features ............................................ 22
 Selecting the Sound Mode (depending on
the model) ..................................................... 23




Teletext Feature (depending on the model) .. 50
Wall Mount Kit Specifications (VESA) ........... 52
Setting Up Your Remote Control ................... 53
How to assemble the Stand-Base
(depending on the model) ............................. 58
 Troubleshooting ............................................ 58
 Specifications ................................................ 59
☛
➢
Important
Note
Symbols
Press
English - 3
BN68-01352A-01Eng.indd 3
2007-10-06 ¿ÀÈÄ 5:49:44
Checking Parts
Owner’s Instructions
Remote Control/
AAA Batteries
Cover-Bottom / Screws (2ea)
(PS-50P96FD/PS-58P96FD,
Refer to page 58)
Power Cord
Cloth-Clean
Warranty Card/
Registration Card/
Safety Guide Manual
Ferrite Core
Sold Separately
S-Video Cable
Antenna Cable
Component Cables
Audio Cables
Video Cable
PC Cable
Scart Cable
PC Audio Cable
HDMI Cable
HDMI/DVI Cable
Ferrite Core
➢ The
ferrite cores are used to shield the cables
Side Panel Jack
from interference.
When connecting a cable, open the ferrite
core and clip it around the cable near the
plug.
the ferrite core around the part of the DVI
➢ Turn
cable close to the PC when the HDMI2 port
or
Power Cord
HDMI/DVI
Cable
Headphones Audio Cables/
Cable
Video Cable
Audio Cables/
S-Video Cable
and the PC are connected with the HDMI/DVI
cable. (PS-58P96FD)
Using the Stand-Base
➢
 Two or more people should carry
the PDP. Never lay the PDP on the
floor because of possible damage
to the screen. Always keep the
PDP upright.
 The PDP can rotate 20 degrees in
right and left directions.
-20° ~ 20°
English - 4
BN68-01352A-01Eng.indd 4
2007-10-06 ¿ÀÈÄ 5:49:49
Control Panel
Front (or Side) Panel
PS-50P96FD/PS-58P96FD
PS-63P76FD
➢ The product colour and shape may vary depending on the model.
1 SOURCE
Displays a menu of all of the available input
sources (TV, Ext.1, Ext.2, AV, S-Video,
Component, PC, HDMI1, HDMI2, HDMI3, and
DTV).
In the on-screen menu, use this button as
you would use the ENTER/OK button on
the remote control.
(PS-50P96FD/PS-58P96FD)
➢
4
C/P.
Press to change channels. In the on-screen
menu, use the
C/P.
buttons as
you use the ▲ and ▼ buttons on the remote
control.
5
(ENTER/OK)
Press to confirm a selection.
6
(Power) button
Press to turn the TV on and off.
2 MENU
Press to see the on-screen menu of your TV’s
features.
3 +−
Press to increase or decrease the volume.
In the on-screen menu, use the +−
buttons as you use the ◄ and ► buttons on
the remote control.
Power Indicator
Blinks and turns off when the power is on and
lights up in stand-by mode.
Remote Control Sensor
Aim the remote control towards this spot on
the TV.
7 Speaker
English - 5
BN68-01352A-01Eng.indd 5
2007-10-06 ¿ÀÈÄ 5:49:58
Connection Panel
Side Panel
8
(PS-58P96FD)
1
2
or
3
➢ The product colour and shape may vary depending on the model.
1 HDMI IN 3
Connect to the HDMI jack of a device with
HDMI output.
2 S-VIDEO or VIDEO / AUDIO L/R
Video (S-Video or Video) and audio inputs for
external devices, such as a camcorder or VCR.
3 Headphones jack
You can connect a set of headphones if you
wish to watch a television programme without
disturbing the other people in the room.
Prolonged use of headphones at a high
volume may damage your hearing.
➢
Rear Panel
1
or
0
Cable Television
Network
8
6
or
2
➢
☛
3
4
5
7
9
The product colour and shape may vary depending on the model.
 Whenever you connect an audio or video system to your set, ensure that all elements are
switched off.
 When connecting an external device, match the colour of the connection terminal to the cable.
Continued...
English - 6
BN68-01352A-01Eng.indd 6
2007-10-06 ¿ÀÈÄ 5:50:04
1 POWER IN
Connect the supplied power cord.
2 Connecting external Audio Devices
Connect RCA audio signals from the TV to an
external source, such as Audio equipment.
3 EXT 1, EXT 2
Inputs or outputs for external devices, such as
VCR, DVD, video game device or video disc
players.
Input/Output Specification
Connector
EXT 1
EXT 2
Input
Output
Video Audio(L/R) RGB Video + Audio(L/R)
Only TV or DTV
✔
✔
✔
output is available.
Output you can
✔
✔
choose.
4 COMPONENT IN
Audio (AUDIO L/R) and video (Y/PB/PR) inputs
for Component.
5 DIGITAL AUDIO OUT (OPTICAL)
Connect to a Digital Audio Component.
6 SERVICE
− Connector for service.
− Connect the serial jack between the
electro-motion wall mount bracket and your
TV when you want to adjust the TV viewing
angle using your remote control.
7 PC IN / AUDIO
Connect to the video and audio output jack on
your PC.
8 COMMON INTERFACE Slot
Insert CI (Common Interface) card into the slot.
(refer to page 45)
− When not inserting “CI CARD” in some
channels, “Scramble Signal” is displayed on
the screen.
− The pairing information containing a
telephone number, CI CARD ID, Host ID,
and other information will be displayed in
about 2~3 minutes. If an error message
is displayed, please contact your service
provider.
− When the channel information configuration
has finished, the message “Updating
Completed” is displayed, indicating that the
channel list is now updated.
Insert the CI-Card in the direction marked
on it.
9 HDMI IN 1, HDMI IN 2
− Connect to the HDMI jack of a device with
HDMI output. These inputs can also be used
as a DVI connection with separate analog
audio inputs. An optional HDMI/DVI cable
will be necessary to make this connection.
When using the optional HDMI/DVI adapter,
the DVI analog audio inputs on your TV
allow you to receive left and right audio from
your DVI device. (Not compatible with PC)
− When connecting this product via HDMI or
DVI to a Set Top Box, DVD Player or Games
Console etc, make sure that it has been
set to a compatible video output mode as
shown in the table below. Failure to observe
this may result in picture distortion, image
breakup or no picture.
− Do not attempt to connect the HDMI/DVI
connector to a PC or Laptop Graphics Card.
(This will result in a blank screen being
displayed)
− The TV may not output sound and pictures
may be displayed with abnormal color
when DVD players/Cable Boxes/Satellite
receivers supporting HDMI versions older
than 1.3 are connected. When connecting
an older HDMI cable and there is no sound,
connect the HDMI cable to the HDMI IN
2 jack and the audio cables to the DVI IN
(HDMI2) [R-AUDIO-L] jacks on the back of
the TV. If this happens, contact the company
that provides the external device to confirm
the HDMI version, then request an upgrade.
DVI IN (HDMI 2) AUDIO L/R
DVI audio outputs for external devices.
0 ANT IN
75Ω Coaxial connector for Aerial/Cable
Network.
Supported modes for HDMI and Component
HDMI/DVI 50Hz
HDMI/DVI 60Hz
Component
480i 480p 576i 576p 720p 1080i 1080p
X
X
X
O
O
O
O
X
O
X
X
O
O
O
O
O
O
O
O
O
X
➢
English - 7
BN68-01352A-01Eng.indd 7
2007-10-06 ¿ÀÈÄ 5:50:10
Viewing the Remote Control
➢
 This is a special remote control for the visually impaired persons, and has Braille points on the
Power, Channel, Volume, STOP, and PLAY/PAUSE buttons.
 The performance of the remote control may be affected by bright light.
1 POWER button
(turns the TV on and off)
2 Number buttons for direct
channel access
3 One/Two-digit channel
selection
4 Channel control button
(Refer to page 15)
5 Selects the TV and DTV
mode directly
6
Volume increase
Volume decrease
7 Temporary sound switch-off
8 Displays the main on-screen
menu
9 Returns to the previous
menu
@ Picture size selection
# Electronic Program Guide
(EPG) display
$ Sound mode selection
% Remote control setup
^ Selects a target device to be
controlled by the Samsung
remote control (TV, DVD,
STB, CABLE, VCR)
& Press to backlight the VOL,
CH, and the active source
button (TV, DVD, CABLE,
STB, VCR) on the remote.
* Available source selection
( Previous channel
) DTV menu display
a Records for Live
Broadcasting
b VCR/DVD Function (Rewind,
Stop, Play/Pause, Fast/
Forward)
c
Next channel
Previous channel
d Exit the on-screen menu
e Control the cursor in the
menu
f Use to see information on
the current broadcast
g Runs the Anynet+ view
functions and sets up
Anynet+ devices.
h Picture-In-Picture On/Off
i Picture effect selection
(Refer to page 18)
j Digital subtitle display
k Picture freeze
l If your remote control is not
functioning properly, take out
the batteries and press the
reset button for about 2~3
seconds.
Reinsert the batteries and
try using the remote control
again.
Teletext Functions
(Refer to page 50)
5 Exit from the teletext display
(depending on the model)
8 Teletext index
0 Fastext topic selection
! Teletext display/mix both
teletext information and the
normal broadcast
@ Teletext size
* Teletext mode selection
(LIST/FLOF)
( Teletext sub page
c P :Teletext next page
P :Teletext previous page
d Teletext cancel
f Teletext reveal
h Teletext hold
i Teletext store
Continued...
English - 8
BN68-01352A-01Eng.indd 8
2007-10-06 ¿ÀÈÄ 5:50:12
Installing Batteries in the Remote Control
1
2
3
Lift the cover at the back of the remote control upward as
shown in the figure.
Install two AAA size batteries.
 Make sure to match the “+” and “–” ends of the
batteries with the diagram inside the compartment.
 Do not mix battery types, i.e. alkaline and manganese.
Close the cover as shown in the figure.
Remove the batteries and store them in a cool and dry
place if you won’t be using the remote control for a long
time. The remote control can be used up to about 23 feet
from the TV. (Assuming typical TV usage, the batteries last
for about one year.)
➢
➢
remote control doesn’t work! Check the following:
➢ If1.the
Is the TV power on?
2. Are the plus and minus ends of the batteries reversed?
3. Are the batteries drained?
4. Is there a power cut, or is the power cord unplugged?
5. Is there a special fluorescent light or a neon sign nearby?
Switching Your Television On and Off
The main lead is attached to the rear of the television.
1 Plug the main lead into an appropriate socket.
The main voltage is indicated on the rear of the television and the frequency is 50 or 60Hz.
2 Press the (Power) button (On/Off) on the front of the television or press the POWER button on the
remote control to switch the television on. The programme that you were watching last is reselected
automatically. If you have not yet stored any channels, no clear picture appears. Refer to “Storing
Channels Automatically” on page 13 or “Storing Channels Manually” on page 14.
If the television is initially powered on, several basic customer settings proceed automatically.
Refer to “Plug & Play Feature” on page 10.
3 To switch the television off, press the (Power) button (On/Off) on the front of the television or press
the POWER button on the remote control.
4 To switch the TV on, press the (Power) button (On/Off) on the front of the TV or press the POWER
button or number buttons on the remote control.
➢
➢
English - 9
BN68-01352A-01Eng.indd 9
2007-10-06 ¿ÀÈÄ 5:50:17
Viewing the Menus
1
2
3
4
5
Press the MENU button.
The main menu is displayed on the screen.
Its left side has five icons: Picture, Sound, Channel, Setup,
and Input.
Press the ▲ or ▼ button to select one of the icons.
Press the ENTER/OK button to access the icon’s sub-menu.
Press the ▲ or ▼ button to move to items in the menu.
Press the ENTER/OK button to enter items in the menu.
Press the ▲/▼/◄/► button to change the selected items.
Press the RETURN button to return to the previous menu.
Press the EXIT button to exit from the menu.
TV
Picture
Mode
: Dynamic
Contrast
Brightness
Sharpness
Colour
Tint
G 50
Colour Tone
: Cool1
Detailed Settings

100
45
75
55
R 50


 More
Move
Enter
Exit
Plug & Play Feature
When the television is initially powered on, several basic
customer settings proceed automatically and subsequently.
The following settings are available.
If you accidentally select the wrong country for your TV, the
characters on the screen may be wrongly displayed.
Any functions related to Digital TV (DVB) will only work in
countries or areas where DVB-T (MPEG2) digital terrestrial
signals are broadcasted. Please confirm with your local dealer if
you can receive DVB-T signals. Although this TV set follows the
DVB-T specification, maintaining compatibility with the future
coming DVB-T digital terrestrial broadcasts is not guaranteed.
Several functions may not be available in some countries.
1 If the television is in standby mode, press the POWER button
on the remote control. The message Start Plug & Play is
displayed. Press the ENTER/OK button.
2 The Language menu will automatically appear after several
seconds.
3 Select the appropriate language by pressing the ▲ or ▼ button.
Press the ENTER/OK button. The message Select Home
Mode when installing this TV at home. is displayed.
4 Press the ◄ or ► button to select Shop or Home, then press
the ENTER/OK button. The message to check the connected
status of the antenna is displayed.
The default selection is Home.
We recommend setting the TV to Home mode for the best
picture in your home environment.
Shop mode is only intended for use in retail environments.
If the unit is accidentally set to Shop mode, and you want to
return to Dynamic (Home) mode, press the Volume button
and then hold down the MENU button for five seconds on
the TV panel.
5 Make sure that the antenna is connected to the TV.
Press the ENTER/OK button. The Country menu is displayed.
Plug & Play
☛
☛
Start Plug & Play.
OK
Enter
Exit
Plug & Play
English
Deutsch
Français
Italiano
▼
Language
Move
Enter
Skip
Plug & Play
Select Home Mode
When installing this TV at home.
Home
Shop
Move
Enter
Skip
Plug & Play
➢
➢
➢
➢
Check antenna input.
OK
Enter
Skip
Plug & Play
Country
Move
▲
United Kingdom
Austria
Eastern Europe
▼
Enter
Skip
Continued...
English - 10
BN68-01352A-01Eng.indd 10
2007-10-06 ¿ÀÈÄ 5:50:19
6
Select your country or area by pressing the ▲ or ▼ button.
Plug & Play
Press the ENTER/OK button.
Some DTV functions may not be available.
The message Some DTV functions may not be available.
Digitally Scan?
Digitally Scan? is displayed.
No
Yes
This function is supported for all countries except for the
following 6 countries: the United Kingdom, Austria, France,
Move
Enter
Skip
Germany, Italy, Spain.
If your country supports the DTV functions, the message is
Plug & Play
not displayed. Then you can follow the instructions from step
Auto Store
P 1
C
-40 MHz
12. When the local service provider does not support DTV
0 %
broadcasting but you choose a DTV supporting country, it
enters the DTV Plug & Play but DTV functions may not work
Start
properly.When No is selected, follow the instructions from step
Enter
Skip
7 to 10. When Yes is selected, follow the instructions from
step 11.
Plug & Play
Select No pressing the ◄ or ► button, then press the ENTER/
Clock Set
OK button. Auto Store menu is displayed.
Month Day
Year Hour Minute
Press the ENTER/OK button to start search the channels. The
01
01
2007
00 : 00
channel search will start and end automatically. After all the
available channels are stored, Clock Set menu is automatically
Adjust
Move
Enter
displayed. Press the ENTER/OK button.
To stop the search before it has finished, press the
Plug & Play
ENTER/OK button with Stop selected.
Press the ◄ or ► button to select Month, Day, Year, Hour, or
Minute. Set these by pressing the ▲ or ▼ button.
0%
You can set the Month, Day, Year, Hour, or Minute
Services found: 0
Channel: directly by pressing the numeric buttons on the remote
Start
control.
Press the ENTER/OK button to confirm your setting. The
Skip
message Enjoy your viewing is displayed. When you have
finished, press the ENTER/OK button.
Plug & Play
Even if the ENTER/OK button is not pressed, the message
will automatically disappear after several seconds.
Scanning for digital services...
Select Yes pressing the ◄ or ► button, then press the
29%
ENTER/OK button. Auto Store menu is displayed.
Services found: 6
Channel: 35
Press the ENTER/OK button to start search the analog
Stop
channels. The analog channel search will start and end
automatically. After all the available analog channels are stored,
Skip
the screen for searching digital channels is automatically
displayed.
Plug & Play
To stop the search before it has finished, press the
ENTER/OK button with Stop selected.
The Iberian Peninsula and Balears Islands
Press the ENTER/OK button to start search the digital
Canarian Islands
channels. The digital channel search will start and end
automatically. After all the available digital channels are stored,
the screen to select a time zone is displayed depending on the
country.
Move
Select
Skip
To stop the search before it has finished, press the
ENTER/OK button with Stop selected.
If the DTV channel is updated, the Source in the source list
of the Input menu is automatically changed to DTV.
For detailed descriptions about DTV channel update, refer
to page 36 of this manual.
Press the ▲ or ▼ button to select required time zone, then press the ENTER/OK button. The screen
for setting the time is displayed. Press the ENTER/OK button.
➢
7
8


➢
9
➢
10
➢
11
12
➢
13
➢
➢
➢
14
Continued...
English - 11
BN68-01352A-01Eng.indd 11
2007-10-06 ¿ÀÈÄ 5:50:23
15 Press the ◄ or ► button to select Month, Day, Year, Hour, or
Minute. Set these by pressing the ▲ or ▼ button.
You can set the Month, Day, Year, Hour, or Minute
directly by pressing the numeric buttons on the remote
control.
16 Press the ENTER/OK button to confirm your setting. The
message Enjoy your viewing is displayed. When you have
finished, press the ENTER/OK button.
Even if the ENTER/OK button is not pressed, the message
will automatically disappear after several seconds.
➢
Plug & Play
Set the current time.
Month
Day
Year
01
15
2007
Hour
Minute
12
00


Adjust
➢
Move
Select
Skip
Enjoy your viewing
OK
If you want to reset this feature …
1 Press the MENU button to display the menu.
2 Press the ▲ or ▼ button to select Setup, then press the
ENTER/OK button.
3 Press the ENTER/OK button again to select Plug & Play.
The message Start Plug & Play is displayed.
TV
Setup
Plug & Play
Language
Time
Game Mode
Blue Screen
Melody
PC
Home Theatre PC
Light Effect
 More
Move




: Off

: Off

: Off


: Off
: Standby Mode On 
: English
Enter
Return
Viewing External Signal Sources
You can switch between viewing signals from connected
equipment, such as a VCR, DVD, Set-Top Box, and the TV
source (broadcast or cable).
1 Press the MENU button to display the menu.
2 Press the ▲ or ▼ button to select Input, then press the
ENTER/OK button.
3 Press the ENTER/OK button again to select Source List.
4 Press the ▲ or ▼ button to select the signal source, then press
the ENTER/OK button.
Available signal sources: TV, Ext.1, Ext.2, AV, S-Video,
Component, PC, HDMI1, HDMI2, HDMI3, DTV
TV
Input
Source List
: TV
Edit Name
Anynet+(HDMI-CEC)
Move
TV
Return
Source List
TV
Ext.1
Ext.2
AV
S-Video
Component
PC
HDMI1
HDMI2
HDMI3
DTV
Move
➢
Enter


: −−−−
: −−−−
: −−−−
: −−−−
: −−−−
: −−−−
: −−−−
: −−−−
: −−−−
: −−−−
Enter
Return
You can select these options simply by pressing the SOURCE
button on the remote control.
watch television programme again, press the TV/DTV button
➢ To
and select the channel number required.
English - 12
BN68-01352A-01Eng.indd 12
2007-10-06 ¿ÀÈÄ 5:50:25
Editing Device Names
You can give a name to the external source.
1 Press the MENU button to display the menu.
2 Press the ▲ or ▼ button to select Input, then press the
ENTER/OK button.
3 Press the ▲ or ▼ button to select Edit Name, then press the
ENTER/OK button.
4 Press the ▲ or ▼ button to select the external source to be
edited, then press the ENTER/OK button.
5 Select the required device by pressing ▲ or ▼, then press the
ENTER/OK button.
Available device names: VCR, DVD, D-VHS, Cable STB, HD
STB, Satellite STB, AV Receiver, DVD Receiver, Game,
Camcorder, DVD Combo, DHR (DVD HDD Recorder), PC.
6 Press the EXIT button to exit.
When a PC with a resolution of 1920 x 1080@60Hz is
connected to the HDMI IN 2 port, you should set the HDMI2
mode to PC in the Edit Name of the Input mode.
If the HDMI2 mode is not PC, it works depending on the TV
setting.
Source List
: TV
Edit Name
Anynet+(HDMI-CEC)
Move
(availability depends on your country).
Automatically allocated programme numbers may not
correspond to actual or desired programme numbers. However
you can sort numbers manually and clear any channels you do
not wish to watch.
1 Press the MENU button to display the menu.
2 Press the ▲ or ▼ button to select Channel, then press the
ENTER/OK button.
3 Press the ENTER/OK button again. The available countries are
listed.
4 Select your country by pressing the ▲ or ▼ button, then press
the ENTER/OK button.
Even though you have changed the country setting in this
menu, the country setting for DTV is not changed. Use the
Plug & Play function to change the country setting for DTV.
(Refer to pages 10 to 12)
5 Press the ▲ or ▼ button to select Auto Store, then press the
ENTER/OK button.
6 Press the ENTER/OK button again to start the search.
The search will end automatically.
To stop the search before it has finished, press the MENU
or the ENTER/OK button.
➢
➢
Enter
TV


Return
Edit Name
: −−−−−−−−
: −−−− VCR
: −−−− DVD
: −−−−D-VHS
: −−−−
Cable STB
: −−−−
HD STB
: −−−−
Satellite STB
: −−−− ▼
: −−−−
Ext.1
Ext.2
AV
S-Video
Component
PC
HDMI1
HDMI2
HDMI3
➢
Storing Channels Automatically
➢ Not available in DTV or external input mode.
You can scan for the frequency ranges available to you
Input
TV
Move
Enter
TV
Return
Channel
▲
Country
: United Kingdom
Switzerland
Auto Store
United Kingdom
Manual Store
Austria
Channel Manager
Eastern Europe
Sort
Others
Name
▼
Fine Tune
LNA
: Off
Move
Enter
TV
Return
Channel
Country
: United Kingdom 

Auto Store

Manual Store

Channel Manager

Sort

Name

Fine Tune

LNA
: Off
Move
Enter
Return
Auto Store
P 1
C
--
40 MHz
0 %
Start
Enter
Return
English - 13
BN68-01352A-01Eng.indd 13
2007-10-06 ¿ÀÈÄ 5:50:29
Storing Channels Manually
➢ Not available in DTV or external input mode.
You can store television channels, including those received via
cable networks.
When storing channels manually, you can choose:
 Whether or not to store each of the channels found.
 The programme number of each stored channel which you wish
to identify.
1 Press the MENU button to display the menu.
2 Press the ▲ or ▼ button to select Channel, then press the
ENTER/OK button.
3 Press the ▲ or ▼ button to select Manual Store, then press
the ENTER/OK button.
4 Select the required option by pressing the ▲ or ▼ button, then
press the ENTER/OK button.
5 When you are satisfied with your setting, press the ENTER/OK
button.
6 Press the EXIT button to exit.
TV
Channel
Country
: United Kingdom

Auto Store

Manual Store

Channel Manager

Sort

Name

Fine Tune

LNA
: Off
Move
TV
Enter
Return
Manual Store
Programme
Colour System
Sound System
Channel
Search
Store
:P 1
: Auto
: BG
4
:C
: 63 MHz
:?


Move
Enter
Return
 Programme (Programme number to be assigned to a channel)
− Press the ▲ or ▼ button until you find the correct number.
You can also select the channel number directly by pressing the numeric buttons (0~9).
 Colour System: Auto/PAL/SECAM/NTSC4.43
− Press the ▲ or ▼ button to select the required colour standard.
 Sound System: BG/DK/I/L
− Press the ▲ or ▼ button to select the required sound standard.
 Channel (When you know the number of the channel to be stored)
− Press the ▲ or ▼ button to select C (Air channel) or S (Cable channel).
− Press the ► button, then press the ▲ or ▼ button to select the required number.
You can also select the channel number directly by pressing the numeric buttons (0~9).
If there is abnormal sound or no sound, reselect the sound standard required.
 Search (When you do not know the channel numbers)
− Press the ▲ or ▼ button to start the search.
− The tuner scans the frequency range until the first channel or the channel that you selected is
received on the screen.
 Store (When you store the channel and associated programme number)
− Set to OK by pressing the ENTER/OK button.
➢
➢
➢
Channel mode
☛
P (Programme mode): When completing tuning, the broadcasting stations in your area have
been assigned to position numbers from P00 to P99. You can select a channel by entering the
position number in this mode.
 C (Air channel mode): You can select a channel by entering the assigned number to each air
broadcasting station in this mode.
 S (Cable channel mode): You can select a channel by entering the assigned number for each
cable channel in this mode.
English - 14
BN68-01352A-01Eng.indd 14
2007-10-06 ¿ÀÈÄ 5:50:30
Adding / Locking Channels
➢ Not available in DTV or external input mode.
Using the Channel Manager, you can conveniently lock or add
TV
channels.
1 Press the MENU button to display the menu.
2 Press the ▲ or ▼ button to select Channel, then press the
ENTER/OK button.
3 Press the ▲ or ▼ button to select Channel Manager, then
press the ENTER/OK button.
 Adding channels
Using the Channel List, you can add channels.
4
5
Channel
Country
: United Kingdom

Auto Store

Manual Store

Channel Manager

Sort

Name

Fine Tune

LNA
: Off
Move
TV
Select Channel List by pressing the ENTER/OK button.
Move to the ( ) field by pressing the ▲/▼/◄/► buttons,
select a channel to be added, and press the ENTER/OK button
to add the channel.
If you press the ENTER/OK button again, the ( ) symbol
next to the channel disappears and the channel is not
added.
Enter
Return
Channel Manager
Channel List
Child Lock


: Off
➢
 Locking channels
This feature allows you to prevent unauthorized users, such as
children, from watching unsuitable programmes by muting out video
and audio.
6
Press the ▲ or ▼ button to select Child Lock, then press the ENTER/
OK button.
7 Select On by pressing the ▲ or ▼ button, then press the ENTER/OK
button.
8 Press the ▲ or ▼ button to select Channel List, then press the
ENTER/OK button.
9 Move to the ( ) field by pressing the ▲/▼/◄/► buttons, select a
channel to be locked, and press the ENTER/OK button.
If you press the ENTER/OK button again, the ( ) symbol next to
the channel disappears and the channel lock is canceled.
A blue screen is displayed when Child Lock is activated.
10 Press the EXIT button to exit.
➢
➢
Move
Enter
Return
Channel List
P 1 C4
1 / 10
Prog.
0
1
2
3
4
5
6
7
8
9
▲
C -C4
C 24
C2
C5
C 80
C7
C 36
C 52
C 11
Add
Move
Page
▼
Lock
Enter
Return
You can select these options simply by pressing the CH LIST
➢ button
on the remote control.
English - 15
BN68-01352A-01Eng.indd 15
2007-10-06 ¿ÀÈÄ 5:50:33
Sorting the Stored Channels
Not available in DTV or external input mode.
➢
This operation allows you to change the programme numbers
of the stored channels.
This operation may be necessary after using the auto store.
1 Press the MENU button to display the menu.
2 Press the ▲ or ▼ button to select Channel, then press the
ENTER/OK button.
3 Press the ▲ or ▼ button to select Sort, then press the ENTER/
OK button.
4 Select the channel that you wish to move by pressing the ▲ or
▼ button, then press the ENTER/OK button.
5 Select the number of the programme to which the channel is to
be moved by pressing the ▲ or ▼ button.
Press the ENTER/OK button. The channel is moved to its new
position and all other channels are shifted accordingly.
6 Repeat steps 4 to 5 until you have moved all the channels to
the required programme numbers.
7 Press the EXIT button to exit.
Assigning Names to Channels
Not available in DTV or external input mode.
➢
Channel names will be assigned automatically when channel
information is broadcast. These names can be changed,
allowing you to assign new names.
1 Press the MENU button to display the menu.
2 Press the ▲ or ▼ button to select Channel, then press the
ENTER/OK button.
3 Press the ▲ or ▼ button to select Name, then press the
ENTER/OK button.
4 Press the ▲ or ▼ button to select the channel to be assigned to
a new name, then press the ENTER/OK button.
5 Press the ▲ or ▼ button to select a letter, a number, or a
symbol (Results in this sequence: A~Z, 0~9, +, -, *, /, blank).
Move on to the previous or next letter by pressing the ◄ or ►
button, then press the ENTER/OK button.
6 Repeat steps 4 to 5 for each channel to be assigned to a new
name.
7 Press the EXIT button to exit.
TV
Channel
Country
: United Kingdom

Auto Store

Manual Store

Channel Manager

Sort

Name

Fine Tune

LNA
: Off
Move
Enter
TV
Return
Sort
Prog.
0
1
2
3
4
Ch.

C−−
C76
C5
C6
C7

Move
TV
Name

Enter
Return
Channel
Country
: United Kingdom

Auto Store

Manual Store

Channel Manager

Sort

Name

Fine Tune

LNA
: Off
Move
Enter
TV
Return
Name
Prog.
0
1
2
3
4
Move
Ch.

C−−
C76
C5
C6
C7

Name
−−−−−
−−−−−
−−−−−
−−−−−
−−−−−
Enter
Return
English - 16
BN68-01352A-01Eng.indd 16
2007-10-06 ¿ÀÈÄ 5:50:36
Fine Tuning Channel Reception
➢ Not available in DTV or external input mode.
If the reception is clear, you do not have to fine tune the
channel, as this is done automatically during the search and
store operation.
If the signal is weak or distorted, you may have to fine tune the
channel manually.
1 Press the MENU button to display the menu.
2 Press the ▲ or ▼ button to select Channel, then press the
ENTER/OK button.
3 Press the ▲ or ▼ button to select Fine Tune, then press the
ENTER/OK button.
4 To obtain a sharp, and clear picture and good sound quality,
press the ◄ or ► button until you reach the optimal setting.
Press the ENTER/OK button.
To reset the fine tuning to 0, select Reset by pressing the
▲ or ▼ button. Press the ENTER/OK button.
5 Press the EXIT button to exit.
Fine Tune Store will change the colour of the Channel OSD
(On Screen Display) from White to Red and add the “*”
mark.
TV
Channel
Country
: United Kingdom

Auto Store

Manual Store

Channel Manager

Sort

Name

Fine Tune

LNA
: Off
Move
Enter
Return
Fine Tune
P 1
➢
+3
Reset
Adjust
Save
Return
➢
P 1*
Mono
Picture
Sound
SRS TS XT
−− : −−
: Dynamic
: Custom
: Off
LNA (Low Noise Amplifier)
This function is very useful in the situation that the TV is used
TV
Channel
in weak signal.
Country
: United Kingdom

Auto Store
LNA amplifies the TV signal in the weak signal area, a low-noise

Manual Store
preamplifier boosts the incoming signal.

Channel Manager

Sort
1 Press the MENU button to display the menu.

Name

Fine Tune
2 Press the ▲ or ▼ button to select Channel, then press the

LNA
: Off
ENTER/OK button.
3 Press the ▲ or ▼ button to select LNA, then press the ENTER/
Move
Enter
Return
OK button.
4 Select Off or On by pressing the ▲ or ▼ button, then press the
ENTER/OK button.
5 Press the EXIT button to exit.
Depending on areas, factory mode of LNA, will be set up as On or Off.
➢
English - 17
BN68-01352A-01Eng.indd 17
2007-10-06 ¿ÀÈÄ 5:50:37
Changing the Picture Standard
You can select the type of picture which best corresponds to
your viewing requirements.
1 Press the MENU button to display the menu.
2 Press the ENTER/OK button to select Picture.
3 Press the ENTER/OK button again to select Mode.
4 Select the required mode by pressing the ▲ or ▼ button, then
press the ENTER/OK button.
Available modes: Dynamic, Standard, Movie
The settings values may vary depending on the input
source. (ex. RF, Video, Component, PC, or HDMI)
5 Press the EXIT button to exit.
TV
Picture
Mode
: Dynamic
Contrast
Brightness
Sharpness
Colour
Tint
G 50
Colour Tone
: Cool1
Detailed Settings

100
45
75
55
R 50


 More
Move
➢
TV
Enter
Return
Picture
Dynamic
Mode
: Dynamic
Standard
Contrast
Movie
Brightness
Sharpness
Colour
Tint
G 50
R
Colour Tone
: Cool1

Detailed Settings
100
45
75
55
50
 More
Move
➢
➢
Enter
Return
You can select these options simply by pressing the P.MODE
button on the remote control.
 Choose Dynamic for viewing the TV during the day or
when there is bright light in the room.
 Choose Standard for general TV watching mode.
 Choose Movie when viewing the movie.
Customizing the Picture Settings
Your television has several setting options that allow you to
control the picture quality.
1 Press the MENU button to display the menu.
2 Press the ENTER/OK button to select Picture.
3 Press the ENTER/OK button again to select Mode.
4 Select the required mode by pressing the ▲ or ▼ button, then
press the ENTER/OK button.
Available modes: Dynamic, Standard, Movie
5 Select the required option by pressing the ▲ or ▼ button, then
press the ENTER/OK button.
6 When you are satisfied with your setting, press the ENTER/OK
button.
7 Press the EXIT button to exit.
TV
Picture
Mode
: Dynamic
Contrast
Brightness
Sharpness
Colour
Tint
G 50
Colour Tone
: Cool1
Detailed Settings

100
45
75
55
R 50


 More
Move
TV
Enter
Return
Picture
Mode
: Dynamic
Contrast
Brightness
Sharpness
Colour
Tint
G 50
Cool2 R
Colour Tone
: Cool1
Cool1
Detailed Settings
Normal �
Warm1
 More
Warm2
100
45
75
55
50
 Contrast – Brightness – Sharpness – Colour – Tint
In TV, AV, S-Video modes of the PAL system, you cannot
use the Tint Function.
Contrast – Brightness – Colour Tone : PC Mode
Move
Enter
Return
Press the ◄ or ► button until you reach the optimal setting.
 Colour Tone: Cool2/Cool1/Normal/Warm1/Warm2
When the picture mode is set to Dynamic or Standard, Warm1 and Warm2 cannot be selected.
 Reset: Cancel/OK
Select OK. You can return to the factory defaults picture settings.
The reset function is set for each picture mode and colour tone.
➢
➢
➢
English - 18
BN68-01352A-01Eng.indd 18
2007-10-06 ¿ÀÈÄ 5:50:38
Configuring Detailed Settings on the Picture
You can set detailed picture settings.
1 Press the MENU button to display the menu.
2 Press the ENTER/OK button to select Picture.
3 Press the ▲ or ▼ button to select Detailed Settings, then
press the ENTER/OK button.
4 Select the required option by pressing the ▲ or ▼ button, then
press the ENTER/OK button.
Available options: Black Adjust, Dynamic Contrast, Gamma,
White Balance, My Colour Control, Edge Enhancement,
Colour Space, xvYCC
5 When you are satisfied with your setting, press the ENTER/OK
button.
6 Press the EXIT button to exit.
When the picture mode is set to Movie or Standard, Detailed
➢ Settings
can be selected.
If DNIe is Off, the Detailed Settings cannot be selected when
➢ the
Picture mode is in Standard mode.
TV
Picture
Mode
: Movie
Contrast
Brightness
Sharpness
Colour
Tint
G 50
Colour Tone
: Warm2
Detailed Settings

80
45
10
53
R 50


 More
Move
TV
Enter
Return
Detailed Settings
Black Adjust
Dynamic Contrast
Gamma
White Balance
My Colour Control
Edge Enhancement
Colour Space
xvYCC
Move
: Off
: Off
: 0
: Off
: Auto
: Off
Enter








Return
 Black Adjust: Off/Low/Medium/High
You can directly select the black level on the screen to adjust the screen depth.
 Dynamic Contrast: Off/Low/Medium/High
You can adjust the screen contrast so that the optimal contrast is provided.
 Gamma: -3 ~ +3
You can adjust the middle brightness of pictures.
Press the ◄ or ► button until you reach the optimal setting.
 White Balance: R-Offset/G-Offset/B-Offset/R-Gain/G-Gain/B-Gain/Reset
You can adjust the colour temperature for more natural picture colors.
R-Offset/G-Offset/B-Offset/R-Gain/G-Gain/B-Gain: Changing the adjustment value will refresh the
adjusted screen.
Select the required option by pressing the ▲ or ▼ button, then press the ENTER/OK button. Press
the ◄ or ► button until you reach the optimal setting.
Reset: The previously adjusted white balance will be reset to the factory defaults.
 My Colour Control: Pink/Green/Blue/White/Reset
This setting can be adjusted to suit your personal preferences.
Pink/Green/Blue/White: Changing the adjustment value will refresh the adjusted screen.
Select the required option by pressing the ▲ or ▼ button, then press the ENTER/OK button. Press
the ◄ or ► button until you reach the optimal setting.
Reset: The previously adjusted colours will be reset to the factory defaults.
 Edge Enhancement: Off/On
You can emphasize object boundaries.
 Colour Space: Auto/Wide
You can set the colour reproduction space for the input signal to Auto or Wide.
 xvYCC: Off/On
Setting the xvYCC mode to On increases detail and colour space when watching movies from an
external device (ie. DVD player) connected to the HDMI or Component IN jacks. You must set the
Picture Mode to Movie to enjoy this feature.
The xvYCC function works only in Component or HDMI mode.
➢
English - 19
BN68-01352A-01Eng.indd 19
2007-10-06 ¿ÀÈÄ 5:50:40
Selecting the Picture Size
You can select the picture size which best corresponds to your
TV
Picture
viewing requirements.
 More
Size
: Auto Wide 
1 Press the MENU button to display the menu.
Screen Mode
: 16 : 9


Digital
NR
: Auto
2 Press the ENTER/OK button to select Picture.
Active Colour
: On


DNIe
: On
3 Press the ▲ or ▼ button to select Size, then press the ENTER/

Movie Plus
: On
OK button.

Reset
: OK
4 Select the required option by pressing the ▲ or ▼ button, then
press the ENTER/OK button.
Move
Enter
Return
Available options: Auto Wide, 16:9, Wide Zoom, Zoom, 4:3,
Just Scan
TV
Size
 Auto Wide: Expands and pulls up the picture from 4:3 to
Auto Wide
16:9
16:9 ratio.
Wide Zoom
 16:9: Sets the picture to 16:9 wide mode.
Zoom
4:3
 Wide Zoom: Magnifies the size of the picture more than
Just Scan
4:3. Move the screen up/down using the ▲ or ▼ button
after selecting the by pressing the ► or ENTER/OK
button.
 Zoom: Magnifies the size of the picture vertically on
Move
Enter
Return
screen.
 4:3: Sets the picture to 4:3 normal mode.
 Just Scan: Displays the input scenes as they are without
any cutoff when HDMI 720p, 1080i, 1080p signals are
input.
With the HDMI Just Scan picture size, depending on
the AV devices, the screen may be cut off or a specific
colour appears on the screen.
5 Press the EXIT button to exit.
You can change the picture size simply by pressing the P.SIZE button on the remote control.
Depending on the input source, the picture size options may vary.
The items available may differ depending on the selected mode.
➢
➢
➢
➢
Positioning and Sizing the screen using Zoom
 Resizing the screen using the Zoom enables the positioning and sizing of the screen to up/down
direction using the ▲ or ▼ button as well as the screen size.
 Move the screen up/down using the ▲ or ▼ button after selecting the by pressing the ◄ or ►
button.
 Resize the screen vertically using the ▲ or ▼ button after selecting the by pressing the ◄ or ►
button.
Selecting the Screen Mode
When setting the picture size to Auto Wide in a 16:9 wide TV,
TV
you can determine the picture size you want to see the 4:3
WSS (Wide Screen Service) image or nothing. Each individual
European country requires different picture size so this
function is intended for users to select it.
1 Press the MENU button to display the menu.
2 Press the ENTER/OK button to select Picture.
3 Press the ▲ or ▼ button to select Screen Mode, then press
the ENTER/OK button.
4 Select the required option by pressing the ▲ or ▼ button, then
press the ENTER/OK button.
Available options: 16:9, Wide Zoom, Zoom, 4:3
 16:9: Sets the picture to 16:9 wide mode.
 Wide Zoom: Magnifies the size of the picture more than 4:3.
 Zoom: Magnifies the size of the picture vertically on screen.
 4:3: Sets the picture to 4:3 normal mode.
5 When you are satisfied with your setting, press the ENTER/OK button.
6 Press the EXIT button to exit.
Picture
 More
Size
Screen Mode
Digital NR
Active Colour
DNIe
Movie Plus
Reset
Move
: Auto Wide
: 16 : 9
: Auto
: On
: On
: On
: OK
Enter







Return
English - 20
BN68-01352A-01Eng.indd 20
2007-10-06 ¿ÀÈÄ 5:50:41
Digital NR / Active Colour / DNIe / Movie Plus
1
2
3
4
5



TV
Picture
Press the MENU button to display the menu.
 More
Press the ENTER/OK button to select Picture.
: Auto Wide 
Size
Select the required option by pressing the ▲ or ▼ button, then

: 16 : 9
Screen Mode

: Auto
Digital NR
press the ENTER/OK button.

: On
Active Colour

: On
DNIe
Available options: Digital NR, Active Colour, DNIe, Movie

: On
Movie Plus
Plus

: OK
Reset
When you are satisfied with your setting, press the ENTER/OK
button.
Return
Enter
Move
Press the EXIT button to exit.
Digital NR: Off/Low/Medium/High/Auto
If the signal received by the television is weak, you can activate this feature to reduce any static and
ghosting that may appear on the screen.
Active Colour: Off/On
If you turn on this option, the colours of the sky and grass will be stronger and clearer for a more vivid
on-screen picture.
This function is not available in PC mode.
This function is not available in Movie and Standard mode.
DNIe: Off/Demo/On
This TV includes the DNIe function so as to provide a high visual quality. If you set DNIe to on, you
can view the screen with the DNIe feature activated. If you set the DNIe to Demo, you can view the
applied DNIe and normal pictures on the screen, for demonstration purposes. Using this function, you
can view the difference in the visual quality.
DNIeTM (Digital Natural Image engine)
This feature brings you more detailed image with 3D noise reduction, detail enhancement,
contrast enhancement and white enhancement. New image compensation Algorithm gives
brighter, clearer, more detailed image to you. DNIeTM technology will fit every signal into your
eyes.
This function is not available in PC mode.
Movie Plus: Off/On
You can view more natural skin and clear text even in fast moving scenes.
The Wide Zoom, Zoom and Just Scan mode are not supported.
➢
➢
➢

➢
➢
Freezing the Current Picture
You can freeze the picture when watching a television
programme simply by pressing the “STILL” button. To return to
normal viewing, press it again.
This function will automatically cancel five minutes later.
➢
English - 21
BN68-01352A-01Eng.indd 21
2007-10-06 ¿ÀÈÄ 5:50:43
Sound Features
1
2
3
4
5


TV
Sound
Press the MENU button to display the menu.

Mode
: Custom
Press the ▲ or ▼ button to select Sound, then press the
Equalizer

ENTER/OK button.

SRS TS XT
: Off
: Off

Auto Volume
Select the required option by pressing the ▲ or ▼ button, then

Internal Mute
: Off

Sound Select
: Main
press the ENTER/OK button.
Reset
Available options: Mode, Equalizer, SRS TS XT, Auto Volume,
Internal Mute, Sound Select, Reset
When you are satisfied with your setting, press the ENTER/OK
Move
Enter
Return
button.
Press the EXIT button to exit.
< If Game Mode is On >
Mode: Standard/Music/Movie/Speech/Custom
TV
Sound
You can select the type of special sound effect to be used when

Mode
: Custom
watching a given broadcast.
Equalizer


SRS TS XT
: Off
Equalizer: Balance/100Hz/300Hz/1kHz/3kHz/10kHz
: Off

Auto Volume

Internal Mute
: Off
The television has several settings which allow you to control

Sound Select
: Main
the sound quality.
Reset
If you make any changes to these settings, the sound mode
is automatically switched to Custom.
SRS TS XT: Off/On
Move
Enter
Return
TruSurround XT is a patented SRS technology that solves
the problem of playing 5.1 multichannel content over
TV
Equalizer
two speakers. TruSurround delivers a compelling, virtual
surround sound experience through any two-speaker
R
+
+
playback system, including internal television speakers. It is
0
0
fully compatible with all multichannel formats.
TruSurround XT, SRS and
L
Symbol are trademarks of SRS Labs,
Balance 100Hz 300Hz 1kHz 3kHz 10kHz
Inc. TruSurround XT technology is
incorporated under license from SRS
Move
Adjust
Return
Labs, Inc.
Auto Volume: Off/On
Each broadcasting station has its own signal conditions, and so it is not easy to adjust the volume
every time the channel is changed. This feature lets you automatically adjust the volume of the
desired channel by lowering the sound output when the modulation signal is high or by raising the
sound output when the modulation signal is low.
Internal Mute: Off/On
If you want to hear the sound through separate speakers, cancel the internal amplifier.
The +, - and MUTE buttons do not operate when the Internal Mute is set to On.
When Internal Mute is set to On, the Sound menus except for Sound Select (in PIP mode)
cannot be adjusted.
Sound Select: Main/Sub
When the PIP feature is activated, you can listen to the sound of the sub (PIP) picture.
− Main: Used to listen to the sound of the main picture.
− Sub: Used to listen to the sound of the sub picture.
Reset
If Game Mode is On, the Reset Sound function is activated. Selecting the Reset function after setting
the equalizer resets the equalizer setting to the factory defaults.
➢

➢


➢
➢


TRADEMARK & LABEL LICENSE NOTICE
Manufactured under license from Dolby Laboratories.
“Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
English - 22
BN68-01352A-01Eng.indd 22
2007-10-06 ¿ÀÈÄ 5:50:46
Selecting the Sound Mode (depending on the model)
The DUAL I-II button displays/controls the processing and
output of the audio signal. When power is switched on, the
mode is automatically preset to either “DUAL-I” or “Stereo”,
depending on the current transmission.
Type of broadcast
Regular broadcast
(Standard audio)
NICAM
Mono
(Normal)
NICAM Stereo
NICAM
stereo
Mono
(Normal)
NICAM DUAL-I/II
➢
Mono (Normal use)
Regular + NICAM Mono
NICAM
Stereo
A2
Stereo
On-screen indication
NICAM
dual-1
Regular broadcast
(Standard audio)
Bilingual or DUAL-I/II
Dual I
Stereo
Stereo
Mono
(Normal)
NICAM
dual-2
Mono (Normal use)
Dual II
Mono
(Forced mono)
 If the receiving conditions deteriorate, listening will be easier if the mode is set to Mono.
 If the stereo signal is weak and automatic switching occurs, switch to Mono.
English - 23
BN68-01352A-01Eng.indd 23
2007-10-06 ¿ÀÈÄ 5:50:47
Time Features
1
2
TV
Setup
Press the MENU button to display the menu.

Plug & Play
Press the ▲ or ▼ button to select Setup, then press the

Language
: English
ENTER/OK button.

Time

Game Mode
: Off
3 Press the ▲ or ▼ button to select Time, then press the

Blue Screen
: Off

Melody
: Off
ENTER/OK button.

PC
4 Select the required option by pressing the ▲ or ▼ button, then

Home Theatre PC : Off
Standby
Mode
On

Light
Effect
:
press the ENTER/OK button.
 More
Available options: Clock Set, Sleep Timer, Timer 1, Timer 2,
Move
Enter
Return
Timer 3
TV
Time
5 When you are satisfied with your setting, press the ENTER/OK
button.
Clock Set
: 00 : 00


Sleep Timer
: Off
6 Press the EXIT button to exit.
Timer 1
: Inactivated 
Timer 2
: Inactivated 
 Clock Set
Timer 3
: Inactivated 
You can set the television clock so that the current time is
displayed when pressing the INFO button on the remote control.
You must also set the time if you wish to use the automatic on
or off timers.
Move
Enter
Return
− Press the ◄ or ► button to select Month, Day, Year, Hour,
or Minute. Set these by pressing the ▲ or ▼ button.
TV
Timer 1
You can set the Month, Day, Year, Hour, or Minute
On Time
directly by pressing the numeric buttons on the remote
00 :
00
No
control.
Off Time
00 :
00
No
In the event of a power interruption or the set being turned
Repeat
Volume
off at the supply, the settings for the Clock will be lost.
Once
10
 Sleep Timer
Programme
You can select a time period of between 30 and 180 minutes
01
after which the television automatically switches to standby
Move
Adjust
Return
mode.
− Select the preset time interval (Off, 30, 60, 90, 120, 150, or
180) for staying on by pressing the ▲ or ▼ button.
 Timer 1 / Timer 2 / Timer 3
You can set the On/Off timers so that the television will switch
on or off automatically at the time you select.
You must set the clock first.
− Press the ◄ or ► button to select the required item below.
Press the ▲ or ▼ button to adjust to the setting satisfied.
On Time : Select hour, minute, and No/Yes. (To activate timer with the setting satisfied, set to
Yes.)
Off Time : Select hour, minute, and No/Yes. (To activate timer with the setting satisfied, set to
Yes.)
Repeat : Select Once, Everyday, Mon~Fri, Mon~Sat, or Sat~Sun.
Volume : Select the required volume level.
Programme : Select the required channel.
You can set the hour, minute, and channel directly by pressing the number buttons on the remote
control.
➢
➢
☛
➢
Power Off
☛ Auto
When you set the timer “On”, the TV will eventually turn off, if no controls are operated for 3 hours
after the TV was turned on by the timer. This function is only available in timer “On” mode and
prevents overheating, which may occur if a TV is on for too long time.
English - 24
BN68-01352A-01Eng.indd 24
2007-10-06 ¿ÀÈÄ 5:50:49
Language / Blue Screen / Melody / Light Effect /
Energy Saving / HDMI Black Level
1
2
3
4
5






TV
Setup
Press the MENU button to display the menu.

Plug & Play
Press the ▲ or ▼ button to select Setup, then press the

Language
: English
ENTER/OK button.

Time

Game Mode
: Off
Select the required option by pressing the ▲ or ▼ button, then

Blue Screen
: Off

Melody
: Off
press the ENTER/OK button.

PC
Available options: Language, Blue Screen, Melody,

Home Theatre PC : Off
Light Effect
: Standby Mode On 
Light Effect, Energy Saving, HDMI Black Level
 More
When you are satisfied with your setting, press the ENTER/OK
Move
Enter
Return
button.
TV
Setup
Press the EXIT button to exit.
 More
Language

Wall-Mount Adjustment
It is variable depending on the model. When you start using the
Energy Saving
: Off


HDMI Black Level : Normal
television for the first time, you must select the language which

PIP
will be used for displaying menus and indications.
Screen Burn Protection

Blue Screen: On/Off
If no signal is being received or the signal is very weak, a blue
screen automatically replaces the noisy picture background. If
Move
Enter
Return
you wish to continue viewing the poor picture, you must set the
Blue Screen to Off.
Melody: Off/Low/Medium/High
The TV power on/off melody sound can be adjusted.
Light Effect: Off/Standby Mode On/Watching Mode On/On
You can turn on/off the blue LED on the front of TV according to the situation. Use it for saving power
or when the LED dazzles your eyes.
− Off: Switches off the Energy Saving mode.
− Standby Mode On: The blue LED lights while in Standby mode and it turns off when your TV is
turned on.
− Watching Mode On: The blue LED lights when watching TV and it turns off when your TV is
turned off.
− On: The blue LED always lights.
Set the Light Effect to Off to reduce the power consumption.
Energy Saving: Off/Low/Medium/High
This feature adjusts the screen brightness depending on the surrounding lighting conditions.
− Off: Switches off the Energy Saving mode.
− Low: Operates in standard mode regardless of the surrounding illumination.
− Medium: Enters Medium power saving mode regardless of the surrounding illumination.
− High: Enters maximum power saving mode regardless of the surrounding illumination.
HDMI Black Level: Normal/Low
Using this function, you can adjust the image quality when the screen burn (appearance of black
level, low contrast, low colour, etc.) is encountered by the HDMI input for RGB limited range (16 to
235).
This function is active only when the externel input connects to HDMI(RGB signals).
➢
➢
English - 25
BN68-01352A-01Eng.indd 25
2007-10-06 ¿ÀÈÄ 5:50:51
Using the Game Mode
When connecting to a game console such as PlayStationTM or
TV
Setup
XboxTM, you can enjoy a more realistic gaming experience by
Plug & Play


Language
: English
selecting game menu.

Time

Game Mode
: Off
1 Press the MENU button to display the menu.

Blue Screen
: Off
2 Press the ▲ or ▼ button to select Setup, then press the

Melody
: Off

PC
ENTER/OK button.

Home Theatre PC : Off
3 Press the ▲ or ▼ button to select Game Mode, then press the
Light Effect
: Standby Mode On 
 More
ENTER/OK button.
4 Select Off or On by pressing the ▲ or ▼ button, then press the
Move
Enter
Return
ENTER/OK button.
5 Press the EXIT button to exit.
To disconnect the game console and connect another external device, cancel game mode in the
Setup menu.
If you display the TV menu in Game mode, the screen shakes slightly.
Game Mode is not available in TV mode.
If Game Mode is On :
 Picture Mode is automatically changed to Standard and users cannot change the mode.
 Sound Mode in the Sound menu is deactivated. Adjust the sound using the equalizer.
 The Reset Sound function is activated. Selecting the Reset function after setting the
equalizer resets the equalizer setting to the factory defaults.
➢
➢
➢
➢
English - 26
BN68-01352A-01Eng.indd 26
2007-10-06 ¿ÀÈÄ 5:50:51
Wall- mount adjustment (Sold separately) (PS-50P96FD)
Once the wall mount is installed, the position of your TV can be easily adjustable.
Rear Panel
Auto Wall-Mount
Serial Cable(1P to 1P)(Not supplied)
Entering the menu
1
2
3
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Setup, then press the
ENTER/OK button.
Press the ▲ or ▼ button to select Wall-Mount Adjustment,
then press the ENTER/OK button.
Adjust to the desired position using the ▲/▼/◄/► buttons.
Press the EXIT button to exit.
press an arrow button when no OSD is displayed on the
➢ IfTVyouscreen,
the Adjustment screen appears.
you turn the power off, your TV moves to the initial
➢ When
installation position.When you turn the power on, your TV
TV
Setup
 More
Wall-Mount Adjustment
Energy Saving
: Off
HDMI Black Level : Normal
PIP
Screen Burn Protection
Move
Enter





Return
Wall-Mount Adjustment
Position1
moves to the last remembered position you adjusted.
Using the remote Control Buttons
Button
(Red)
(Green) (Yellow)
Operations
Wall-mount
angle
adjustment
Tilt Up, Tilt Down, Move
right, Move left
Reset
Moves to the initial
installation position
Remembering
the position and
moving to the
remembered
position
Remembers 3 positions
with the Red, Green and
Yellow buttons.
Moves to the remembered
position using these 3
colour buttons.
Position
Adjust
1
INFO
2
Centre
3
Exit
installation, refer to the Installation Manual provided.
➢ For
product installation and the installation and moving of the wall mount, make sure to consult a
➢ For
specialized installation company.
installation manual is to be used when attaching the wall mount to a wall. When attaching to
➢ This
other building materials, please contact your nearest dealer.
English - 27
BN68-01352A-01Eng.indd 27
2007-10-06 ¿ÀÈÄ 5:50:53
Viewing the Picture in Picture (PIP)
You can display a sub picture within the main picture. In this
way you can watch TV programme or monitor the video input
from any connected devices.
1 Press the MENU button to display the menu.
2 Press the ▲ or ▼ button to select Setup, then press the
ENTER/OK button.
3 Press the ▲ or ▼ button to select PIP, then press the ENTER/
OK button.
4 Select the required option by pressing the ▲ or ▼ button, then
press the ENTER/OK button.
Available options: PIP(On/Off), Source, Size, Position,
Programme
5 When you are satisfied with your setting, press the ENTER/OK
button.
6 Press the EXIT button to exit.
 PIP: On/Off
You can activate or deactivate the PIP function.
You can select these options simply by pressing the PIP
button on the remote control.
➢
TV
Setup
 More
Wall-Mount Adjustment
Energy Saving
: Off
HDMI Black Level : Normal
PIP
Screen Burn Protection
Move
TV
Enter





Return
PIP
PIP
Source
Size
Position
Programme
Move
: On
: TV
:
:
:P 1
Enter





Return
Table of PIP Settings
Main Picture
Component
HDMI1, 2, 3
PC
Sub Picture
Analog TV broadcasts only
Ext1, Ext2
 Source: TV/Ext.1/Ext.2/AV
You can select a source of the sub-picture.
 Size:
/
/
You can select a size of the sub-picture.
If main picture is in PC and Component mode, Size is not available.
 Position:
/
/
/
You can select a position of the sub-picture.
 Programme
You can select a channel of the sub-picture only when the Source is set to TV.
➢
English - 28
BN68-01352A-01Eng.indd 28
2007-10-06 ¿ÀÈÄ 5:51:01
Screen Burn Protection
To reduce the possibility of screen burn, this unit is equipped
with screen burn prevention technology. This technology
enables you to set picture movement up/down (Vertical Line)
and side to side (Horizontal Dot). The Time setting allows
you to programme the time between movement of the picture
in minutes.
1 Press the MENU button to display the menu.
2 Press the ▲ or ▼ button to select Setup, then press the
ENTER/OK button.
3 Press the ▲ or ▼ button to select Screen Burn Protection,
then press the ENTER/OK button.
4 Select the required option by pressing the ▲ or ▼ button, then
press the ENTER/OK button.
Available options: Pixel Shift, All White, Signal Pattern, Side
Gray
5 When you are satisfied with your setting, press the ENTER/OK
button.
6 Press the EXIT button to exit.
 Pixel Shift: Using this function, you can minutely move pixels
on the PDP in horizontal or vertical direction to minimize after
image on the screen.
− Set Pixel Shift to On by pressing the ▲ or ▼ button, then
press the ENTER/OK button.
− Select the required option by pressing the ▲ or ▼ button,
then press the ENTER/OK button.
Available options: Horizontal Dot, Vertical Line, Time
Optimum condition for pixel shift;
➢
PC
Horizontal Dot
Vertical Line
Time (minute)
1
1
2 min
TV/Ext/AV/S-Video/
Component/HDMI/DTV
2
2
2 min
TV
Setup
 More
Wall-Mount Adjustment
Energy Saving
: Off
HDMI Black Level : Normal
PIP
Screen Burn Protection
Move
TV
Enter





Return
Screen Burn Protection
Pixel Shift
All White
Signal Pattern
Side Gray
Move
TV
: Dark
Enter




Return
Pixel Shift
Pixel Shift
Horizontal Dot
Vertical Line
Time
Move
: On
:2
:2
: 2 min
Enter




Return
➢ The Pixel Shift value may differ depending on the monitor size (inches) and mode.
 All White: This function helps remove after images on the screen by changing the colour of pixels to
white. Use this function when there are remaining after images or symbols on the screen especially
when you displayed a still image on the screen for a long time.
 Signal Pattern: This function helps remove after images on the screen by moving all the pixels on
the PDP according to a pattern. Use this function when there are remaining after images or symbols
on the screen especially when you displayed a still image on the screen for a long time.
 Side Gray: When you watch TV with the screen ratio of 4:3, the screen is prevented from any
damage by adjusting the white balance on both extreme left and right sides.
Dark: When you set the screen ratio to 4:3, it darkens the left and right sides.
Light: When you set the screen ratio to 4:3, it brightens the left and right sides.
To remove after images on the screen, use either All White or Signal Pattern function. Although
both of the two functions remove after images on the screen, Signal Pattern is more effective.
The after image removal function has to be executed for a long time (approximately 1 hour) to
effectively remove after images on the screen. If after image is not improved after the execution of the
function, repeat the function again.
Press any button on the remote control to cancel this feature.
➢
➢
➢
English - 29
BN68-01352A-01Eng.indd 29
2007-10-06 ¿ÀÈÄ 5:51:03
Setting up Your PC Software (Based on Windows XP)
The Windows display-settings for a typical computer
are shown below. But the actual screens on your PC will
probably be different, depending upon your particular
version of Windows and your particular video card. But even
if your actual screens look different, the same, basic set-up
information will apply in almost all cases. (If not, contact your
computer manufacturer or Samsung Dealer.)
1 Right click the mouse on the Windows Desktop, then click on
Properties.
The Display Properties will be displayed.
2 Click on Settings tab, then set the Display Mode with
reference to the Display Modes Table. You do not need to
change the Colours settings.
3 Click on Advanced. A new settings dialog box will be
displayed.
4 Click on the Monitor tab, then set the Screen refresh rate with reference to the Display Modes
Table. Set the Vertical Frequency and Horizontal Frequency individually if you can do so instead of
setting the Screen refresh rate.
5 Click on OK to close the window, then Click on OK button to the Display Properties window.
Automatic rebooting may commence at this moment.
English - 30
BN68-01352A-01Eng.indd 30
2007-10-06 ¿ÀÈÄ 5:51:03
Display Modes
Both screen position and size will vary depending on the type of PC monitor and its resolution.
The resolutions in the table are recommended. (All resolutions between the supported limits are
supported)
D-Sub Input
Mode
IBM
VESA
Resolution
640 x 350
640 x 480
720 x 400
640×480
640×480
640×480
800×600
800×600
800×600
800×600
1024×768
1024×768
1024×768
1024×768
1152 x 864
1280 x 960
1280×1024
1280×1024
1280×1024
1280×1024
1600×1200
1920×1080
Horizontal
Vertical
Frequency (kHz) Frequency (Hz)
31.469
70.086
31.469
59.940
31.469
70.087
35.000
70.000
37.861
72.809
37.500
75.000
43.750
70.000
37.879
60.317
48.077
72.188
46.875
75.000
57.672
72.000
48.364
60.000
56.476
70.069
60.023
75.029
67.500
75.000
60.000
60.000
63.981
60.020
74.620
70.000
76.824
72.000
79.976
75.025
75.000
60.000
66.587
59.934
Pixel Clock
Frequency (MHz)
25.175
25.175
28.322
28.560
31.500
31.500
45.500
40.000
50.000
49.500
78.434
65.000
75.000
78.750
108.000
108.000
108.000
128.943
132.752
135.000
162.000
138.500
Sync Polarity
(H/V)
+/-/-/+
-/+
-/-/-/+
+/+
+/+
+/+
-/-/-/+/+
+/+
+/+
+/+
-/-/+/+
+/+
+/-
Horizontal
Vertical
Frequency (kHz) Frequency (Hz)
31.469
70.086
31.469
59.940
31.469
70.087
37.879
60.317
48.364
60.000
63.981
60.020
66.587
59.934
Pixel Clock
Frequency (MHz)
25.175
25.175
28.322
40.000
65.000
108.000
138.500
Sync Polarity
(H/V)
+/-/-/+
+/+
-/+/+
+/-
HDMI/DVI Input
Mode
IBM
VESA
Resolution
640 x 350
640 x 480
720 x 400
800×600
1024×768
1280×1024
1920×1080
 The interlace mode is not supported.
 The set might operate abnormally if a non-standard video format is selected.
 Separate and Composite modes are supported. SOG is not supported.
English - 31
BN68-01352A-01Eng.indd 31
2007-10-06 ¿ÀÈÄ 5:51:04
Setting the PC
➢ Preset to the PC mode by pressing the SOURCE button.
1
2
3
4
5
6




Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Setup, then press the
ENTER/OK button.
Press the ▲ or ▼ button to select PC, then press the ENTER/
OK button.
Select the required option by pressing the ▲ or ▼ button, then
press the ENTER/OK button.
Available options: Image Lock, Position, Auto Adjustment,
Image Reset
When you are satisfied with your setting, press the ENTER/OK
button.
Press the EXIT button to exit.
Image Lock: Coarse/Fine
The purpose of picture quality adjustment is to remove or
reduce picture noise.
If the noise is not removed by Fine-tuning alone, then adjust the
frequency as best as possible (coarse) and Fine-tune again.
After the noise has been reduced, readjust the picture so that it
is aligned on the centre of screen.
1 Press the ▲ or ▼ button to select Coarse or Fine, then
press the ENTER/OK button.
2 Press the ◄ or ► button to adjust the screen quality,
vertical stripes may appear or the picture may be blurry.
Press the ENTER/OK button.
Position
Adjust the PC’s screen positioning if it does not fit the TV
screen.
1 Adjust the position by pressing the ▲/▼/◄/► button.
2 Press the ENTER/OK button.
Auto Adjustment
Auto adjustment allows the PC screen of set to self-adjust to the
incoming PC video signal.
The values of fine, coarse and position are adjusted
automatically.
Image Reset
You can replace all image settings with the factory default
values.
TV
Setup
Plug & Play
Language
Time
Game Mode
Blue Screen
Melody
PC
Home Theatre PC
Light Effect
 More
Move




: Off

: Off

: Off


: Off
: Standby Mode On 
: English
Enter
TV
Return
PC
Image Lock
Position
Auto Adjustment
Image Reset
Move
TV




Enter
Return
Image Lock
Coarse
Fine
50
31
Move
TV
Enter
Return
Position
Move
Enter
Return
Auto Adjustment in Progress
Please wait.
Image Reset is completed.
Return
English - 32
BN68-01352A-01Eng.indd 32
2007-10-06 ¿ÀÈÄ 5:51:04
Setting the Home Theatre PC
You can view higher quality pictures by configuring the screen
TV
Setup
settings in PC Mode.
Plug & Play


Language
: English
If you set the Home Theatre PC function to On, you can

Time
configure the Detailed Settings (when Picture Mode is set to

Game Mode
: Off

Blue Screen
: Off
Standard or Movie) as in PC Mode.

Melody
: Off

PC
1 Press the MENU button to display the menu.

Home Theatre PC : Off
2 Press the ▲ or ▼ button to select Setup, then press the
Light Effect
: Standby Mode On 
 More
ENTER/OK button.
Move
Enter
Return
3 Press the ▲ or ▼ button to select Home Theatre PC, then
press the ENTER/OK button.
4 Select Off or On by pressing the ▲ or ▼ button, then press the ENTER/OK button.
5 Press the EXIT button to exit.
This function is available only in PC mode.
➢
English - 33
BN68-01352A-01Eng.indd 33
2007-10-06 ¿ÀÈÄ 5:51:05
Previewing the DTV Menu System
➢
 The company does not guarantee the normal operation
of the DTV menu for countries other than the 6 supported
countries (England, Germany, France, Italy, Spain, Austria)
because only these country standards are supported. In
addition, when the country of the broadcast stream differs
from the country selected by the current user, the string
appearing in the channel banner, Info, Guide, Channel List,
etc. may not be displayed properly.
 Available in DTV mode. Preset to the DTV mode by using
the TV/DTV button on your remote control.
To help you navigate around the on-screen menu system
and adjust the various settings available, refer to the
following illustration.
Press the D.MENU button to display the menu.
Guide
Now & Next Guide
Full Guide
Scheduled List
Default Guide
Now/Next
Full Guide
Channel
Auto Store
Manual Store
Edit Favourite Channels
Channel List
All
Favourites
Default
Setup
Menu Transparency
High
Medium
Low
Opaque
Parental Lock
Parental Rating
Change PIN
Subtitle
Off
On
Subtitle Mode
Normal
Hard of hearing
Audio Format
PCM
Dolby Digital
Digital Text
Disable
Enable
Time Zone
System
Product Information
Signal Information
Software Upgrade
Common Interface
Reset
Guide
Now & Next Guide
Full Guide
Scheduled List
Default Guide
Move

: Full Guide
Enter

Exit
Channel
Auto Store

Manual Store

Edit Favourite Channels

Channel List

Move
Enter
Exit
Setup
Menu Transparency : Medium

Parental Lock

Subtitle
: On

Subtitle Mode
: Normal

Audio Format
: PCM


Move
Enter
Exit
Continued...
English - 34
BN68-01352A-01Eng.indd 34
2007-10-06 ¿ÀÈÄ 5:51:06
Language
Audio Language
Subtitle Language
Teletext Language
Preference
Language
Audio Language

Subtitle Language
Teletext Language
Preference
Primary Audio Language
Secondary Audio Language
Primary Subtitle Language
Secondary Subtitle Language
Primary Teletext Language
Secondary Teletext Language
Move

Enter
Exit
➢ The sub-items of the CI Menu may vary depending on the CAM model. (refer to page 45)
Displaying Programme Information
While viewing a channel, additional information about the
current programme may be displayed.
 While viewing a programme, press the INFO button.
The programme information is displayed.
The information is displayed:
− Parental Rating
− Video Type: SD, HD, Radio
− Audio Type: Mono, Stereo, Dual, Dolby Digital
− Existence of Teletext or DVB Subtitle
− Audio Language
To exit from banner information, press the INFO button.
➢
21:49 Sat 1 May
1 AFDO, 16:9
AFDO, 16:9
No Block
SD
Stereo
Subtitle
English
All Channels
14:20 - 14:33
Contains video with AFD O; coded frame
is 16:9
Exit
➢
English - 35
BN68-01352A-01Eng.indd 35
2007-10-06 ¿ÀÈÄ 5:51:08
Operating the DTV Menu
Viewing the DTV Menu
After installing your antenna system and TV with appropriate connectors.
 Plug in the AC main power and switch on the TV.
 Press the D.MENU button to bring up the DTV menu.
The main menu appears on the screen. Its left side has four icons: Guide, Channel, Setup, and
Language.
1.
Channel
This menu consists of 4 sub-menus:
Auto Store, Manual Store, Edit Favourite Channels, and
Channel List.
 Press the ▲ or ▼ button to select Channel, then press the
ENTER/OK button. The Channel menu is displayed.
Channel
Auto Store

Manual Store

Edit Favourite Channels

Channel List

Move
1.1 Auto Store
You can update the channel list when the broadcaster adds new
services or if you move the TV to a new location.
 Press the ENTER/OK button to select Auto Store. Press
the ENTER/OK button again to start the search. When
it has finished, the number of scanned services will be
displayed.
− The existing favourite channel list will not be deleted
when the channel list is updated.
− To stop the scan before it has finished, press the
ENTER/OK button with Stop selected.
If the signal status is poor, the message No service found!
Check the aerial connection. is displayed.
Enter
Exit
Channel
Auto Store

Manual Store

Edit Favourite Channels

Channel List

Move
Enter
Return
Auto Store
➢
0%
Services found: 0
Channel: -
Start
Return
Channel
1.2 Manual Store
You can specify the channel for a fast channel search.
Auto Store

 − Channel

Manual Store
Press the ▲, ▼ or numeric buttons (0~9) to select a
Edit Favourite Channels

channel.

Channel List
The available channels are 21~68. The corresponding
frequency for the selected channel is automatically set.
− Frequency
Move
Enter
Return
You can specify the frequency (KHz) using the
Manual Store
numeric buttons (0~9). If you do not know the exact
frequency, follow the above step to select the frequency
Channel Frequency
Bandwidth
automatically using channel.
5
177500 KHz 7 MHz
− Bandwidth
Press the ▲ or ▼ button to select a bandwidth. The
available bandwidths are 7 and 8 MHz.
 Press the red button to start the scan for digital services.
Search
When it has finished, channels are updated in the channel
Adjust
Return
list.
You can input by pressing the button on the remote control.
You can not change only frequency and when changing a channel the Frequency will be
automatically changed.


➢
➢
Continued...
English - 36
BN68-01352A-01Eng.indd 36
2007-10-06 ¿ÀÈÄ 5:51:11
Channel
1.3 Edit Favourite Channels
You can edit your favourite channels using the colour buttons.
Auto Store

In the case of DTV mode, OK or Select can be used as the

Manual Store
ENTER/OK button.
Edit Favourite Channels

 Press the red button in the Edit Favourite Channels menu

Channel List
to display all currently stored channels.
 Press the ▲ or ▼ button to select a channel you want.
Press the ENTER/OK button. A ““ icon is shown next to
Move
Enter
Return
the selected channel and the channel will be added to the
Edit Favourite Channels
favourites list.
 To undo, press the ENTER/OK button again.

 Select AlI: Select all channels currently displayed.
1
BBC TWO

2
Five
 Select None: Deselect all selected channels.
3
BBC THREE
 Preview: Displays (a) currently selected
4
abc1
5
QVC
channel(s).

If The Favourite Channels settings have been
Select All
Select None
Preview
completed.
Move
Select
Return
 Add
Edit Favourite Channels
You can use this function when one or more favourite
channels have been selected.
− Press the red button in the Edit Favourite Channels
1
BBC TWO

2
BBC THREE

menu. To add more channels, refer to the previous
3
abc1

section.
− To add all channels to the favourites channel list, press
the red button.
Add
Renumber
Preview
Delete
− To remove all channels, press the green button.
Move
Return
− Preview: Displays (a) currently selected channel(s).
− Press the CH LIST button to display the favourite
channel list.
 Renumber
− In the Edit Favourite Channels menu, press the ▲ or ▼
button to select the required channel.
− Press the green button.
The space for entering the number is a blank.
− Enter the new channel number. Press ENTER/OK button to store or RETURN button to
cancel.
Press the ◄ button to delete an entered digit.
If you enter a number already assigned to another channel, the number is assigned to the
selected channel and the previous number assigned to the selected channel is assigned
to the other channel.
That is, the two numbers are exchanged.
The favorite channels are automatically sorted in ascending order of channel numbers.
 Preview
− In the Edit Favourite Channels menu, press the ▲ or ▼ button to select the channel to be
previewed.
− Press the yellow button. Displays currently selected channel.
 Delete
− In the Edit Favourite Channels menu, press the ▲ or ▼ button to select the channel to be
deleted from the favourite channels list.
− Press the blue button. The selected channel and number will be deleted.
To add a deleted channel back in to the favourite channel list, see Add.
➢
➢
➢
➢
➢
➢
➢
➢
Continued...
English - 37
BN68-01352A-01Eng.indd 37
2007-10-06 ¿ÀÈÄ 5:51:12
Channel List
1.4 Channel List
All Channels-All
You can display a list of all channels or your favourite channels. BBC TWO
1. Test Card ‘M’...
40. BBC NEWS24
806 arte
 Press the ▲ or ▼ button to select Channel List, then
51. BBCi
2. BBC TWO
800 ARD-MHP-DATA
3. Vida003b
press the ENTER/OK button.
801 ARD-OnLine-K..
4. Vida004b
802 BBC ONE
5. Vida005b
It can be displayed simply by pressing the CH LIST
803 MDR FERNSE..
6. Vida006b
804 NDR FERNSEH..
7. BBC THREE
button.
30. CBBC Channel
805 Vida002b
 Press the yellow button to toggle between your favourite
Previous Page
Next Page
Favourites
TV
channels and all channels.
Watch
Move
Return
Your favourite channels are only displayed if they were
previously set in the Edit Favourite Channels menu (refer
to page 37).
 Press the red or green button to display the previous or
next channel list page.
 Press the ▲ or ▼ button to select a channel to be tuned,
then press the ENTER/OK button.
The channel number, name and an icon are displayed in the top left corner while changing
the channel. The channel number and name are displayed if the channel is one of the all
channels, and a  icon if the channel is one of the favourite channels.
 Press the blue button to toggle between your TV, Radio, Data/Other and All.
 Press the CH LIST button to exit from the channel List.
➢
➢
2.
Now & Next Guide
Guide
This menu consists of 4 sub-menus:
Now & Next Guide, Full Guide, Scheduled List, and Default
Guide.
2.1 Now & Next Guide / Full Guide
The EPG (Electronic Programme Guide) information is provided
by the broadcasters. Programme entries may appear blank or
out of date as a result of the information broadcast on a given
channel.
The display will dynamically update as soon as new information
becomes available.
− Now & Next Guide
For the six channels indicated in the left-hand column,
displays the Current programme and the Next programme
information.
− Full Guide
Displays the programme information as time ordered One
hour segments. Two hours of programme information is
displayed which may be scrolled forwards or backwards in
time.
 Press the ▲ or ▼ button to select Now & Next Guide or
Full Guide. Press the ENTER/OK button. The selected
guide menu is displayed.
− Press the red button to toggle between Now & Next
Guide or Full Guide.
− Press the green button to display Favourites or All
Channels list.
− Press the yellow button to scrolls backwards quickly (24
hours).
− Press the blue button to scrolls forwards quickly (24
hours).
You can also display the guide menu simply by
pressing the GUIDE button.
 To watch a programme in the EPG list, press the
▲/▼/◄/► button to select a programme of your choice,
then press the ENTER/OK button.
If the next programme is selected, it is scheduled with the clock icon displayed. If the
ENTER/OK button is pressed again, the scheduling is canceled with the clock icon gone.
For details about scheduling programmes, refer to the section.
Now
Watch
Full Guide
Next
Favourites
Exit
➢
➢
Continued...
English - 38
BN68-01352A-01Eng.indd 38
2007-10-06 ¿ÀÈÄ 5:51:14
 To view programme information, press the ▲/▼/◄/► button to select a programme of your
choice, then press the INFO button.
 Information such as the channel number, programme title and running time, status bar,
and brief summary of the highlighted programme will be displayed in the top right corner
of the screen. If there is a lengthy summary, “…” will be displayed, press the INFO button
for the full summary text.
 Six channels are displayed. To scroll between channels, move to a channel using the ▲
or ▼ button. To display page by page, use the P or
button.
2.2 Scheduled List
Scheduled List
If you make a scheduled viewing list of programmes you may
Thursday 22 Apr
15:30 ~ 18:00 Once
2 BBC TWO
Animal Park
like to see, the channel will be automatically switched to the
Thursday 22 Apr
20:00 ~ 21:00 Once
scheduled programme at the scheduled time even if you are
2 BBC TWO
The Hairy Biker’s
watching another programme.
 Press the red button to add a new programme. The
menu for adding a programme is displayed with Channel
Add Programme
Edit
Delete
selected.
Move
Return
 Press the ▲/▼ and ENTER/OK buttons to set the required
channel, time, date, and frequency. When you are satisfied
Scheduled List
with your settings, save the adjusted schedule by pressing
Channel
810 Super RTL
the red button.
10 : 15 to - - : - Time
 If you want to edit the scheduled programme, select a
programme by pressing the ▲ or ▼ button, then press the
Date
Thu 03 Mar 2005
green button. If necessary, select the programme to be
Frequency
deleted by pressing the ▲ or ▼ button, then press the blue
Save
Cancel
button.
Adjust
Move
Return
When watching analog TV, the reserved DTV channel
cannot be changed. The channel is only changed
automatically to the reserved channel when you are
watching DTV.
Scheduling programme only functions with the
television already turned on, and not from standby
mode. For details about switching the television on and
off automatically, refer to page 9.
➢


➢
➢
2.3 Default Guide
You can preset the default guide style.
 Press the ▲ or ▼ button to select the required option
(Now/Next or Full Guide), then press the ENTER/OK
button. The selected option for default guide is displayed on
the EPG menu and the channel list appears.
Guide
Now & Next Guide
Full Guide
Scheduled List

: Full Guide
Default Guide
Move
Enter

Return
Guide
Now & Next Guide
Full Guide
Scheduled List
Default Guide
Move
Now/Next
Guide
: Full
Full Guide
Enter
Return
Continued...
English - 39
BN68-01352A-01Eng.indd 39
2007-10-06 ¿ÀÈÄ 5:51:19
2.4 All Channels and Favourite Channels
In the EPG menu, you can display all channels or favourite
channels.
 Press the green button repeatedly to toggle between the all
and favourite channels list.
When the favourite channel list has not been set up:
− The message The favourite list is empty. Would you
like to choose your favourite now? is displayed.
− Select Yes. The Edit Favourite Channels menu is
displayed. If you select No, all channels will remain
unchanged.
− To edit the favourite channels, refer to page 37 for more
details.
 All Channels is the list of channels that have been
scanned by the channel list update. All channels
are displayed in the all channel mode.
 Favourites (favourite channels) is the list of
channels that has been set in the Edit Favourite
Channels menu (refer to page 37).
 When there is no channel information, the message
No Data will be displayed and you will not be
able to change the channel even if you press the
ENTER/OK button.
When the message No Data appears and you
cannot change the channel, press the channel
number directly using the numeric buttons.
Guide
Now & Next Guide
Full Guide
Scheduled List
Move
Language
This menu consists of 4 sub-menus:
Audio Language, Subtitle Language, Teletext Language,
and Preference.
Enter

Return
Now & Next Guide
Now
➢
3.

: Full Guide
Default Guide
Watch
Full Guide
Next
Favourites
Exit
Now & Next Guide
The favourites list is empty. Would you like to
choose your favourites now?
Yes
On
Full Guide
No
Favourites
Exit
Language
Audio Language

Subtitle Language
Teletext Language
Preference
Move

Enter
Return
3.1 Audio Language / Subtitle Language / Teletext Language
You can change the default value for subtitle, audio and teletext languages.
 Press the ▲ or ▼ button to select required menu (Audio Language, Subtitle Language, or
Teletext Language), then press the ENTER/OK button. The options of the selected menu are
displayed.
Continued...
English - 40
BN68-01352A-01Eng.indd 40
2007-10-06 ¿ÀÈÄ 5:51:23
Language
3.2 Preference
This menu consists of 6 sub-menus:
Audio Language

Primary Audio Language, Secondary Audio Language,
Subtitle Language
Primary Subtitle Language, Secondary Subtitle Language,
Teletext Language
Primary Teletext Language, and Secondary Teletext

Preference
Language.
Using this feature, users can select one of the languages
(English, German, Italian, Swedish, French, Welsh, Gaelic,
Move
Enter
Return
Irish, Danish, Finnish, Norwegian, Spanish, Czech, and
Preference
Greek). The language selected here is the default when the
user selects a channel.
Primary Audio Language : English 
 Press the ▲ or ▼ button to select required menu (Primary
Secondary Audio Language : English 
Audio Language, Secondary Audio Language, Primary
Primary Subtitle Language : English 
Subtitle Language, Secondary Subtitle Language,
Secondary Subtitle Language : English 
Primary Teletext Language, or Secondary Teletext
Primary Teletext Language : English 
Language), then press the ENTER/OK button.

The options of the selected menu are displayed.
Move
Enter
Return
 Press the ▲ or ▼ button to select required option (English,
Preference
German, Italian, Swedish, French, Welsh, Gaelic, Irish,

Danish, Finnish, Norwegian, Spanish, Czech, or Greek),
Primary Audio Language : English
English
then press the ENTER/OK button.
German
Secondary Audio Language : English
Italian
 If you change the language setting, the Audio
Primary Subtitle Language : English
Swedish
Language, Subtitle Language, and Teletext
French
Secondary Subtitle Language : English
Welsh
Language of the Language menu (refer to page 40)
Primary Teletext Language : English

are automatically changed to the selected language.

 The Audio Language, Subtitle Language, and
Move
Enter
Return
Teletext Language of the Language menu show a
list of languages supported by the current channel and the selection is highlighted. If you
change this language setting, the new selection is only valid for the current channel. The
changed setting does not change the setting of the Primary Audio Language, Primary
Subtitle Language, or Primary Teletext Language of the Preference menu.
➢
Continued...
English - 41
BN68-01352A-01Eng.indd 41
2007-10-06 ¿ÀÈÄ 5:51:26
4.
Setup
This menu consists of 8 sub-menus:
Menu Transparency, Parental Lock, Subtitle, Subtitle Mode,
Audio Format, Digital Text, Time Zone, and System.
4.1 Menu Transparency
You can set the translucency of the on-screen menu.
 Press the ▲ or ▼ button to select required option (High,
Medium, Low, or Opaque), then press the ENTER/OK
button.
Setup
Menu Transparency : Medium

Parental Lock

Subtitle
: On

Subtitle Mode
: Normal

Audio Format
: PCM


Move
Enter
Return
Setup
Menu Transparency : Medium
High
Medium
Parental Lock
Low
Subtitle
: On
Opaque
Subtitle Mode
: Normal
: PCM
Audio Format

Move
4.2 Parental Lock
This feature allows you to prevent unauthorized users, such
as children, from watching unsuitable programmes by a 4-digit
PIN (Personal Identification Number) code that is defined by
the user.
The on-screen menu will instruct you to assign a PIN code (you
can change it later, if necessary).
 Enter your current 4-digit PIN code by using the numeric
buttons (0~9). The Parental Lock menu is displayed with
the Parental Rating selected.
 The default PIN code for a new TV set is 0000.
 If you enter an invalid PIN code, the message
Invalid PIN code. Please try again. is displayed.
 Press the ENTER/OK button. Press the ▲ or ▼ button to
select the age rating you want to lock out, then press the
ENTER/OK button.
 If you want to change the PIN code, press the ▲ or ▼
button to select Change PIN, then press the ENTER/OK
button.
− Enter your new PIN code by using the numeric buttons
(0~9). The message Confirm New PIN is displayed.
− Re-enter your new PIN code to confirm by using the
numeric buttons (0~9). The message Your PIN code
has been changed successfully. is displayed.
If you forget the PIN code, press the remote control buttons
in the following sequence, which resets the PIN to 0-0-0-0:
POWER (Off)  MUTE  8  2  4  POWER (On).
➢
Enter
Return
Setup
Menu Transparency : Medium

Parental Lock

Subtitle
: On

Subtitle Mode
: Normal

Audio Format
: PCM


Move
Enter
Return
Parental Lock
Enter PIN
..
Enter PIN
Return
Change PIN
Enter New PIN
➢
..
Enter PIN
Return
Continued...
English - 42
BN68-01352A-01Eng.indd 42
2007-10-06 ¿ÀÈÄ 5:51:27
Setup
4.3 Subtitle / Subtitle Mode / Audio Format / Digital Text
You can use various settings to suit your personal preferences.
Menu Transparency : Medium

 Press the ▲ or ▼ button to select required menu (Subtitle,

Parental Lock
Subtitle Mode, Audio Format or Digital Text), then press

Subtitle
: On
the ENTER/OK button. The options of the selected menu

Subtitle Mode
: Normal
are displayed.

Audio Format
: PCM
 Press the ▲ or ▼ button to select required option, then

press the ENTER/OK button.
Move
Enter
Return
− Subtitle : On / Off
Setup
You can select these options simply by pressing the
SUBTITLE button on the remote control.
Menu Transparency : Medium
− Subtitle Mode : Normal (basic subtitle) / Hard of hearing
Parental Lock
(subtitle for a hearing-impaired person)
Subtitle
: On
Off
If the programme you are watching does not support
On
Subtitle Mode
: Normal
the Hard of hearing function, Normal automatically
Audio Format
: PCM
activates even though Hard of hearing mode is

selected.
Move
Enter
Return
− Audio Format
Setup
You can only hear Dolby Digital sound through the audio
Menu Transparency : Medium

receiver connected through an optical cable. You can only

Parental Lock
hear PCM sound through the main speaker.

Subtitle
: On
When sound is emitted from both the main speaker and the

Subtitle Mode
: Normal
audio receiver, a sound echo may occur due to the decoding

Audio Format
: PCM
speed difference between the main speaker and the audio

receiver. In this case, use the internal mute function.
Even if you have selected PCM or Dolby Digital in Audio
Move
Enter
Return
Format, when the input signals are any format of PCM
and Dolby Digital, the input format is applied regardless
of the setting. If the input signals are not any of those,
the setting is not applied.
− Digital Text : Enable / Disable (UK only)
If the programme is broadcast with digital text, this
feature is enabled.
MHEG (Multimedia and Hypermedia Information Coding Experts Group)?
An International standard for data encoding systems used in multimedia and hypermedia. This
is at a higher level than the MPEG system which includes data-linking hypermedia such as
still images, character service, animation, graphic and video files as well as multimedia data.
MHEG is user runtime interaction technology and is being applied to various fields including
VOD (Video-On-Demand), ITV (Interactive TV), EC (Electronic Commerce), tele-education,
tele-conferencing, digital libraries and network games.
4.4 Time Zone (Spain only)
Setup
You can select the time zone where you are located.

This menu is only enabled when you select a country
Digital Text
: Enable

supported by the time zone.
Time Zone
➢
➢
➢
➢
➢
➢
System
Move

Enter
Return
Continued...
English - 43
BN68-01352A-01Eng.indd 43
2007-10-06 ¿ÀÈÄ 5:51:29
4.5 System
This menu consists of 5 sub-menus:
Product Information, Signal Information, Software Upgrade,
Common Interface, and Reset.
− Product Information
You can view your product information. For service or repair,
please contact a Samsung approved dealer.
 Press the ENTER/OK button with Product Information
selected. The product information menu is displayed.
− Software Version / Firmware Version
− Signal Information
You can get information about the signal status.
 Press the ENTER/OK button with Signal Information
selected. The technical information for signal status is
displayed.
− Service / Service ID / Multiplex / Network / Bit error
level / Signal Strength
− Software Upgrade (Option)
To keep your product up-to-date with new digital television
features then software upgrades are periodically broadcast
as part of the normal television signal. It will automatically
detect these signals and display the software upgrade
banner. You are given the option to install the upgrade.
 Software Inforamtion
Press the ENTER/OK button, then the current software
version is shown. To display the software version
information, press the ENTER/OK button again.
 Manual Upgrade
Press the ENTER/OK button to search for new software
from the currently broadcasting channels.
 Standby Mode upgrade : On / Off
Press the ENTER/OK button. To continue software
upgrade with master power on, Select On by pressing
the ▲ or ▼ button.
45 minutes after entering standby mode, a manual
upgrade is automatically conducted. Since the power
of the unit is turned on internally, the screen may be
on slightly for the PDP product. This phenomenon may
continue for more than 1 hour until the software upgrade
is completed.
Setup

Digital Text
: Enable

Time Zone
System

Move
Enter
Return
System
Product Information

Signal Information

Software Upgrade

Common Interface

Reset

Move
Enter
Return
Product Information
Software Version: T_BDXPDEU00_0710
Firmware Version: T_STDEU7_102c
Return
Signal Information
Service: ?
Service ID: 0000
Multiplex: ? (TSID 0000,ONID 0000)
Network: ? (ID 0000)
Bit error level:
10
Signal Strength:
0
Return
Software Upgrade
Software Information

Manual Upgrade

Standby Mode upgrade : On

Move
Enter
Return
Continued...
English - 44
BN68-01352A-01Eng.indd 44
2007-10-06 ¿ÀÈÄ 5:51:32
− Common Interface
 Installing the CI Card
Application Info.
a. Purchase the CI CAM module by visiting your nearest
Type: CA
dealer or by phone.
Manufacturer: Canal Plus
b. Insert the CI CARD into the CAM in the direction of
Info: Top Up TV
the arrow until it fits.
c. Insert the CAM with the CI CARD installed into the
common interface slot.
Insert the CAM in the direction of the arrow, right
Return
up to the end so that it is parallel with the slot.
CI Menu
d. Check if you can see a picture on a scrambled signal
channel.
You can install the CAM anytime whether the TV
is ON or OFF.
 Application Info.
This contains information on CAM inserted in the CI slot
and displays it.
− Press the ENTER/OK button to display the
Move
Enter
Exit
information for your application.
 CI Menu
This helps the user select an item from the CAM-supported
menu.
− Press the ENTER/OK button. The options of the selected menu are displayed.
Press the ▲ or ▼ button to select the required option, then press the ENTER/OK button.
Select the CI Menu based on the PC Card menu.
− Reset
You can reset the values stored to the factory default values.
Reset
The Reset operation deletes all channel information
WARNING: All channel settings and user
and user preferences returning all values to their default
preferences will be lost and returned to the
factory defaults. It is recommended that a
factory state.
reset is performed only when serious
 Press the ENTER/OK button with Reset selected. The
problems are experienced.
Enter PIN is displayed.
 Enter your current 4-digit PIN code by using the numeric
buttons (0~9). The warning message is displayed. All
Return
values will be reset by pressing the coloured buttons
(red, green, yellow, and blue) in turn.
The default PIN of a new TV set is “0-0-0-0”.
When PIN is changed in Child Lock, the PIN for
resetting automatically changes.
 When reset is complete, it operates DTV Plug & Play
(DTV Auto Store, Time Zone-depending on the country,
Time Setting) and exits from the digital TV mode without changing to the analog TV mode.
(Refer to page 11)
➢
➢
➢
➢
➢
➢
English - 45
BN68-01352A-01Eng.indd 45
2007-10-06 ¿ÀÈÄ 5:51:33
What is Anynet+?
Anynet+ is an AV network system that enables an easy-to-use AV interface for users by controlling
all connected AV devices through the Anynet+ menu when Samsung Electronics AV devices are
connected.
Connecting Anynet+ Devices
The Anynet+ system supports AV devices supporting Anynet+ only.
Check if there is an Anynet+ mark on the AV device to be connected to the TV.
To directly connect to TV
TV
Anynet+ Device 1 Anynet+ Device 2 Anynet+ Device 3
HDMI 1.3 Cable
HDMI 1.3 Cable
Connect the [HDMI 1], [HDMI
2] or [HDMI 3] jack on the TV
and the HDMI OUT jack of the
corresponding Anynet+ device
using the HDMI cable.
HDMI 1.3 Cable
To connect to Home Theatre
1
TV
Anynet+ Device 1
Anynet+ Device 2
2
HDMI 1.3 Cable
Home Theatre
HDMI 1.3 Cable
HDMI 1.3 Cable
Anynet+ Device 3
Connect the [HDMI 1],
[HDMI 2] or [HDMI 3]
jack on the TV and the
HDMI OUT jack of the
corresponding Anynet+
device using the HDMI
cable.
Connect the HDMI IN jack
of the home theatre and
the HDMI OUT jack of the
corresponding Anynet+
device using the HDMI
cable.
HDMI 1.3 Cable
Optical Cable
only the optical cable between [Digital Audio Out (Optical)] on your TV and Digital Audio
➢ Connect
Input on the receiver.
➢ Connect only one receiver.
can listen to 5.1 channel sound through the home theatre’s speakers. Otherwise, you can only
➢ You
listen to 2 channel stereo sound in other cases. Make sure to connect the Digital Audio IN (Optical) of
➢
➢
➢
the home theatre and the TV correctly to listen to TV sound through the home theatre. However, you
cannot listen to sound from the BD recorder that is sent to the home theatre via the TV in 5.1 channel
sound because the TV outputs only 2 channel stereo sound. Please see the manual for the home
theatre.
You can connect an Anynet+ device using the HDMI cable. Some HDMI cables may not support
Anynet+ functions.
Anynet+ works when the AV device supporting Anynet+ is in the Standby or On status.
Anynet+ supports up to 8 AV devices in total.
English - 46
BN68-01352A-01Eng.indd 46
2007-10-06 ¿ÀÈÄ 5:51:35
Setting Up Anynet+
The following settings are to use Anynet+ functions.
Using the Anynet+ Function
1
2
TV
P1
View TV
Press the Anynet+ button.
Press the ▲ or ▼ button to select Setup, then press the
ENTER/OK button.
Press the ENTER/OK button to select Anynet+ (HDMI-CEC),
then press the ENTER/OK button.
Select Device

Record

Menu on Device

Device Operation

Receiver

Setup
Move
Return
3
➢
➢
➢
Press the ▲ or ▼ button to select On, then press the ENTER/
OK button.
The Anynet+ (HDMI-CEC) function is enabled.
If you select Off, Anynet+ (HDMI-CEC) is disabled.
When the Anynet+ (HDMI-CEC) function is disabled, all the
Anynet+ related operations are deactivated.
:Off

Enter
Setup
Anynet+ (HDMI-CEC)
: OffOff
Auto Turn Off
: OffOn
Searching Connections
Move
Enter
Return
Turning an Anynet+ Device Off Automatically when the TV is Turned Off
2 Press the ▲ or ▼ button to select Auto Turn Off, then press
Setup
the ENTER/OK button.
Anynet+ (HDMI-CEC)
: On
3 Press the ▲ or ▼ button to select On, then press the
ENTER/OK button.
Auto Turn Off
: Off
Off
The Auto Turn Off function is enabled.
Searching Connections
On
If you select Off, the Auto Turn Off function is canceled.
Press the EXIT button to exit.
Move
Enter
Return
The Select Device setting of the TV remote control is to be set
to TV to use the Anynet+ function.
If you set Auto Turn Off to On, connected external devices are also turned off when the TV is turned
off. However, if the device is recording, it may not be turned off.
➢
➢
➢
➢
Scanning and Switching between Anynet+ Devices
1
2
3
4
➢
➢
➢
➢
➢
Press the Anynet+ button.
TV
P1
Press the ▲ or ▼ button to select Select Device, then press
View TV
the ENTER/OK button.
DVDR1

Select Device
Press the ▲ or ▼ button to select to a particular device and
DVDR2
DVD1
Record

press the ENTER/OK button.
DVD2

Menu on Device
It is switched to the selected device.
If you cannot find a device you want, press the ▲ or ▼ button
Device Operation

to select Searching Connections, then press the ENTER/OK
Receiver
:Off

button.

Setup
The meassage Configuring Anynet+ connection... is
Move
Enter
displayed. When searching devices completes, the connected
Return
devices are listed in the Anynet+ menu.
Setup
Switching to the selected devices may take up to 2 minutes.
Anynet+ (HDMI-CEC)
: On

You cannot cancel the operation during the switching
operation.
Auto Turn Off
: On

The time required to scan for devices is determined by the
Searching Connections

number of connected devices.
When the device scan is complete, the number of found
devices is not displayed.
Enter
Return
Move
Although the TV automatically scans devices when it is turned
on using the POWER button, devices connected when the TV is on or under a specific circumstance
are not displayed in the device list. Therefore select Searching Connections menu to search
devices.
If you have selected external input mode by pressing the SOURCE button, you cannot use the
Anynet+ function. Make sure to switch to an Anynet+ device by using the Anynet+ button.
Continued...
English - 47
BN68-01352A-01Eng.indd 47
2007-10-06 ¿ÀÈÄ 5:51:40
Anynet+ Menu
The Anynet+ menu changes depending on the type and status of the Anynet+ devices connected
to the TV.
Anynet+ Menu
View TV
Select Device
Record
Menu on Device
Device Operation
Receiver
Setup
Description
Switches from Anynet+ to TV broadcast mode.
Your TV connects to the corresponding device.
Starts a recording. (This menu works only for a device supporting
recording.)
Shows the menu of the connected device.
Example. When a DVD Recorder is connected, the DVD Recorder’s
title menu appears.
Shows the play control menu of the connected device.
Example. When a DVD Recorder is connected, the play control
menu of the DVD Recorder appears.
Sound is output through the receiver.
You can set the environment for using Anynet+.
TV Remote Control Buttons Available in Anynet+ Mode
Device Type
Anynet+ Device
Operating Status
After switching to the
device, when the menu of
the corresponding device is
displayed on the screen.
After switching to the device,
while playing a file
Available Buttons
Numeric buttons
▲/▼/◄/►/ENTER/OK buttons
Colour buttons
EXIT button
◄◄(Backward search)
►►(Forward search)
(Stop)
► (Play/Pause)
Device with built-in Tuner
After switching to the device,
when you are watching a TV
programme
CH ▲/▼ button
Audio Device
When a Receiver is activated
VOL +/- button
MUTE button
Anynet+ function only works when the remote control is set to TV.
➢ The
REC button works only while in the recordable state.
➢ The
cannot control Anynet+ devices using the buttons on the side of the TV. You can control Anynet+
➢ You
devices only using the TV remote control.
The TV remote control may not work under certain conditions. In this case, reselect the Anynet+
➢ device.
Anynet+ functions don’t operate for the products from other manufacturers.
➢ The
mode, the colour buttons may not work properly.
➢ InTheAnynet+
➢ ◄◄, ►► operations may differ depending on the device.
Recording
You can make a recording of a TV programme using a recorder.
Press the REC button.
Recording begins. (Only when the Anynet+ enabled recording device is connected.)
The current TV programme is recorded in the Watching TV status. If you are watching video from
another device, the video from the device is recorded.
You can also record the source streams by selecting Record after pressing the Anynet+ button.
Before recording, check whether the antenna jack is properly connected to the recording device.
For the antenna connection to the recording device, refer to its user manual.
➢
➢
➢
English - 48
BN68-01352A-01Eng.indd 48
2007-10-06 ¿ÀÈÄ 5:51:40
Listening through a Receiver
You can listen to sound through a receiver instead of the TV speaker.
1 Press the Anynet+ button.
TV
P1
Press the ▲ or ▼ button to select Receiver, then press the
ENTER/OK button.
View TV
2 Press the ◄ or ► button to select to On, then press the
Select Device

ENTER/OK button.
Record

Now you can listen to sound through the receiver.

Menu on Device
3 Press the EXIT button to exit.

Device Operation
When the receiver is set to On, you can listen to the TV sound
Receiver
:On

through the 2-channel receiver.

Setup
If the receiver is exclusively for a home theater only (supporting Move
Enter
audio only), it may not appear in the device list.
Exit
Only when you have connected the optical jack of the TV and
the receiver properly, does Receiver work.
In case of a content with copyright problems, listening through the receiver may not properly operate.
When listening through the receiver, there are restrictions for using the PIP and audio-related menu.
➢
➢
➢
➢
➢
Check Points before Requesting Service
Symptom
Anynet+ does not work.
Solution
■ Check if the device is an Anynet+ device. The Anynet+ system
supports Anynet+ devices only.
■ Connect only one receiver.
■ Check if the Anynet+ device power cord is properly connected.
■ Check the Anynet+ device’s Video/Audio/HDMI 1.3 cable connections.
■ Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+
setup menu.
■ Check whether the TV remote control is in TV mode.
■ Check whether it is Anynet+ exclusive remote control.
■ Anynet+ doesn’t work at a certain condition. (Searching channels)
■ When connecting or removing the HDMI 1.3 cable, please make
sure to search devices again or restart your TV.
■ Check if the Anynet+ Function of Anynet+ device is set on.
I want to start Anynet+.
■ Check if the Anynet+ device is properly connected to the TV and
check if the Anynet+ (HDMI-CEC) is set to On in the Anynet+ Setup
menu.
■ Press the TV button on the TV remote control to switch to TV. Then
press the Anynet+ button to show the Anynet+ menu and select a
menu you want.
I want to exit Anynet+.
■ Select View TV in Anynet+ menu.
■ Press the SOURCE button on the TV remote control and select a
device other than Anynet+ devices.
■ Press any of CH, CH LIST, and PRE-CH to change to the
TV mode. (Note that the channel button operates only when a
tuner-embedded Anynet+ device is not connected.)
The message Connecting to ■ You cannot use the remote control when you are configuring
Anynet+ device… appears on
Anynet+ or switching to a view mode.
the screen.
■ Use the remote control when the Anynet+ setting or switching to
view mode is complete.
The Anynet+ device does not ■ You cannot use the play function when Plug & Play is in progress.
play.
The connected device is not ■ Check whether or not the device supports Anynet+ functions.
displayed.
■ Check whether or not the HDMI 1.3 cable is properly connected.
■ Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+
setup menu.
■ Search Anynet+ devices again.
■ You can connect an Anynet+ device using the HDMI 1.3 cable only.
Some HDMI cables may not support Anynet+ functions.
The TV programme cannot be ■ Check whether the antenna jack on the recording device is properly
recorded.
connected.
The TV sound is not output ■ Connect the optical cable between TV and the receiver.
through the receiver.
English - 49
BN68-01352A-01Eng.indd 49
2007-10-06 ¿ÀÈÄ 5:51:41
Teletext Feature (depending on the model)
Most television stations provide written information services
via teletext. The index page of the teletext service gives you
information on how to use the service. In addition, you can select
various options to suit your requirements by using the remote
control buttons.
For teletext information to be displayed correctly, channel reception
must be stable. Otherwise, information may be missing or some
pages may not be displayed.
☛
1 TV/DTV
Exit from the teletext display (depending on the model)
2
(index)
Used to display the index (contents) page at any time while you are
viewing teletext.
3
4
5
6
7
8
9
0
!
@
#
(teletext on/mix)
Press to activate teletext mode after selecting the channel providing
the teletext service. Press it twice to overlap the teletext with the
current broadcasting screen.
(size)
Press to display the double-size letters in the upper half of the
screen. For lower half of the screen, press it again.
To display normal screen, press it once again.
(mode)
Press to select the teletext mode (LIST/FLOF).
If you press it in the LIST mode, it switches into the List save mode.
In the List save mode, you can save teletext page into list using the
(store) button.
(sub-page)
Used to display the available sub-page.
(page up)
Used to display the next teletext page.
(page down)
Used to display the previous teletext page.
(cancel)
Used to display the broadcast when searching for a page.
(reveal)
Used to display the hidden text (answers to quiz games, for example). To display normal screen,
press it again.
Coloured buttons (red/green/yellow/blue)
If the FASTEXT system is used by a broadcasting company, the different topics covered on a teletext
page are colour-coded and can be selected by pressing the coloured buttons. Press one of them
corresponding to the required. The page is displayed with other coloured information that can be
selected in the same way.
To display the previous or next page, press the corresponding coloured button.
(hold)
Used to hold the display on a given page if the selected page is
linked with several secondary pages which follow on automatically.
To resume, press it again.
(store)
Used to store the teletext pages.
can change teletext pages by pressing the numeric buttons on
➢ You
the remote control.
Continued...
English - 50
BN68-01352A-01Eng.indd 50
2007-10-06 ¿ÀÈÄ 5:51:43
The teletext pages are organized according to six categories:
Part
A
B
C
D
E
F
Contents
Selected page number.
Broadcasting channel identity.
Current page number or search indications.
Date and time.
Text.
Status information.
FASTEXT information.
information is often divided between several pages
➢ Teletext
displayed in sequence, which can be accessed by:
 Entering the page number
 Selecting a title in a list
 Selecting a coloured heading (FASTEXT system)
➢ Press the TV/DTV button to exit from the teletext display.
English - 51
BN68-01352A-01Eng.indd 51
2007-10-06 ¿ÀÈÄ 5:51:53
Wall Mount Kit Specifications (VESA)
Install your wall mount on a solid wall perpendicular to the floor.
When attaching to other building materials, please contact your nearest dealer.
If installed on a ceiling or slanted wall, it may fall and result in severe personal injury.
Product Family
LCD-TV
PDP-TV
inch
VESA Spec. (A * B)
Standard Screw
23 ~ 26
200 * 100
M4
32 ~ 40
200 * 200
M6
46 ~ 52
600 * 400
57
700 * 400
(No VESA)
57 ~ 70
800 * 400
80 ~
1400 * 800
42 ~ 58
600 * 400
70
800 * 400
63
No VESA
80 ~
1400 * 800
Quantity
4
M8
4
M8
6
4
provided the standard dimensions for wall mount kits as shown in the table above.
➢ We
When purchasing our wall mount kit, a detailed installation manual and all parts necessary for
➢ assembly
are provided.
not use screws longer than the standard dimension, as they may cause damage to the inside of
➢ Do
the TV set.
wall mounts that do not comply with the VESA standard screw specifications, the length of the
➢ For
screws may differ depending on their specifications.
Do not use screws that do not comply with the VESA standard screw specifications.
➢ Do
not use fasten the screws too strongly, this may damage the product or cause the product to fall,
leading to personal injury. Samsung is not liable for these kinds of accidents.
Samsung is not liable for product damage or personal injury when a non-VESA or non-specified wall
➢ mount
is used or the consumer fails to follow the product installation instructions.
Our 57” and 63” models do not comply with VESA Specifications. Therefore, you should use our
➢ dedicated
wall mount kit for this model.
➢ Do not exceed 15 degrees tilt when mounting this TV.
Do not install your Wall Mount Kit while your TV is turned on.
It may result in personal injury due to electric shock.
English - 52
BN68-01352A-01Eng.indd 52
2007-10-06 ¿ÀÈÄ 5:51:55
Setting Up Your Remote Control
After it has been set up properly, your remote control can operate in five different modes: TV, VCR,
Cable, DVD, or Set-Top Box. Pressing the corresponding button on the remote control allows you
to switch between these modes, and control whichever piece of equipment you choose.
The remote control might not be compatible with all DVD Players, VCRs, Cable boxes, and Set-Top
Boxes.
Setting Up the Remote to Operate Your VCR
1 Turn off your VCR.
2 Press the VCR button on your TV’s remote control.
3 Press the SET button on your TV’s remote control.
4 Using the number buttons on your remote control, enter three digits
of the VCR code listed on page 55 of this manual for your brand of
VCR. Make sure you enter three digits of the code, even if the first
digit is a “0”. (If more than one code is listed, try the first one.)
5 Press the POWER button on the remote control. Your VCR should
turn on if your remote is set up correctly.
➢
If your VCR does not turn on after set-up, repeat steps 2, 3 and 4,
but try one of the other codes listed for your brand of VCR. If no
other codes are listed, try each VCR code, 000 through 080.
Note on Using Remote Control Modes: VCR
When your remote control is in VCR mode, the volume buttons still
control your TV’s volume.
Setting Up the Remote to Operate Your Cable Box
1 Turn off your cable box.
2 Press the CABLE button on your TV’s remote control.
3 Press the SET button on your TV’s remote control.
4 Using the number buttons on your remote control, enter three digits
of the cable box code listed on page 56 of this manual for your
brand of cable box.
Make sure you enter three digits of the code, even if the first digit is
a “0”. (If more than one code is listed, try the first one.)
5 Press the POWER button on the remote control.
Your cable box should turn on if your remote is set up correctly.
If your cable box does not turn on after set-up, repeat steps 2, 3
and 4, but try one of the other codes listed for your brand of cable
box. If no other codes are listed, try each code, 000 through 046.
Note on Using Remote Control Modes: Cable Box
When your remote control is in CABLE mode, the volume buttons still
control your TV’s volume.
Continued...
English - 53
BN68-01352A-01Eng.indd 53
2007-10-06 ¿ÀÈÄ 5:51:56
Setting Up the Remote to Operate Your DVD
1 Turn off your DVD.
2 Press the DVD button on your TV’s remote control.
3 Press the SET button on your TV’s remote control.
4 Using the number buttons on your remote control, enter three digits
of the DVD code listed on page 57 of this manual for your brand of
DVD. Make sure you enter three digits of the code, even if the first
digit is a “0”. (If more than one code is listed, try the first one.)
5 Press the POWER button on the remote control.
Your DVD should turn on if your remote is set up correctly.
If your DVD does not turn on after set-up, repeat steps 2, 3 and 4,
but try one of the other codes listed for your brand of DVD. If no
other codes are listed, try each code, 000 through 141.
Note on Using Remote Control Modes: DVD
When your remote control is in DVD mode, the volume buttons still
control your TV’s volume.
Setting Up the Remote to Operate Your Set Top Box
1 Turn off your STB.
2 Press the STB button on your TV’s remote control.
3 Press the SET button on your TV’s remote control.
4 Using the number buttons on your remote control, enter three digits
of the STB code listed on page 56 of this manual for your brand of
STB. Make sure you enter three digits of the code, even if the first
digit is a “0”. (If more than one code is listed, try the first one.)
5 Press the POWER button on the remote control.
Your STB should turn on if your remote is set up correctly.
If your STB does not turn on after set-up, repeat steps 2, 3 and 4,
but try one of the other codes listed for your brand of STB. If no
other codes are listed, try each code, 000 through 074.
Note on Using Remote Control Modes: STB
When your remote control is in STB mode, the volume buttons still
control your TV’s volume.
Continued...
English - 54
BN68-01352A-01Eng.indd 54
2007-10-06 ¿ÀÈÄ 5:52:02
Remote Control Codes
VCR
Brand
SAMSUNG
ADMIRAL
AIWA
AKAI
AUDIO DYNAMICS
BELL&HOWELL
BROKSONIC
CANDLE
CANON
CITIZEN
COLORTYME
CRAIG
CURTIS MATHES
DAEWOO
DB
DIMENSIA
DYNATECH
ELECTROHOME
EMERSON
FISHER
FUNAI
GENERAL ELECTRIC
GO VIDEO
LG(Goldstar)
HARMAN KARDON
HITACHI
INSTANT REPLAY
JC PENNEY
JCL
KENWOOD
KLH
LIOYD
LOGIK
LXI
JVC
MAGNAVOX
MARANTZ
MARTA
KONIA
ORION
MEI
MEMOREX
MGA
MIDLAND
MINOLTA
Code
000 001 002 003 004 005 077 078 079
020
025
004 027 032
007 026
018
022
002 003 006 008 015 055
021 056
002 003 006 008 015 055
007
002 024
002 007 008 017 021 025 056 064 066
003 010 011 012 013 014 015 016
007 026
017
025
034
001 003 006 021 022 025 030 032 034
040 047 050 052 060 063 065 066 067
069 073
018 024 028 029 048 051 061
025
002 005 017 021 056
002
006 007 008 009 010
007
019 025 041 042 074
021
002 007 018 019 021 026 037 041
054 056
007 008 018 021 026 037
007 008 018 026 037
070
025
038
025
081 082 083
021 056 059
007 008 018 021 026 037 062
006
036
073 074 075 076
021
006 021 024 025
034
005
019 041 075
Brand
MITSUBISHI
MONTGOMERY WARD
MTC
MULTITECH
NEC
OPTIMUS
PANASONIC
PENTAX
PENTEX RESEARCH+
PHILCO
PHILIPS
PIONEER
PORTLAND
PROSCAN
QUARTZ
QUASAR
RADIO SHACK/
REALISTIC
RCA
SANSUI
SANYO
SCOTT
SEARS
SHARP
SHIMTOM
SIGNATURE
SONY
SYLVANIA
SYMPHONIC
TANDY
TASHIKA
TATUNG
TEAC
TECHNICS
TEKNIKA
TMK
TOSHIBA
TOTEVISION
UNITECH
VECTOR RESEARCH
VICTOR
VIDEO CONCEPTS
VIDEOSONIC
WARDS
YAMAHA
ZENITH
Code
019 034 041 046
020
002 025
002 005 025 038
007 008 018 026 037 062 064
020
021 056 071 072
019 041 075
008
021 056 059
021 080
019 026 039 053
015 049 055
017
018
021 056
006 018 020 021 024 025 029 034
048 056
002 017 019 021 035 041 043 057
068 076
026
018 024
003 047 052 067
006 018 019 024 028 029 041 048 051
020 034 045 015
027 033 038 058
025
027 033 044
021 025 056 059
025
018 025
006
037
025 037 068
021
006 021 025 031
066
003 019 029 051 052
002 006
002
007 026
026
007 026
002
002 003 006 019 020 021 024 025 034
038 041
007 008 018 026 037
023 027 033
Continued...
English - 55
BN68-01352A-01Eng.indd 55
2007-10-06 ¿ÀÈÄ 5:52:08
CABLE BOX
Brand
SAMSUNG
GI
HAMLIN
HITACHI
JERROLD
MACOM
MAGNAVOX
OAK
PANASONIC
PHILIPS
PIONEER
RCA
REGAL
Code
000 001 002 003 004 005 006 007
041
003 024 031
025 030
038 039
025 030
019 023 028
026
003 022 027 037 044
019 021 023 028
004 018 020 044
014 022 040
003
Brand
REGENCY
SA
SCIENTIFIC ATLAN
SPRUCER
STARGATE 2000
SYLVANIA
TEXSCAN
TOCOM
UNIVERSAL
VIEWSTAR
WARNER AMEX
ZENITH
Code
015 023
042 043
042 043
022
036
016
016
032
033 034
019 021 023 028
046
017 029 035 037 045
SAMSUNG SET-TOP BOX
Product
Ground wave STB
CABLE STB
Satellite STB
Code
000 001 002 008 013
000 004 008 013
000 003 008 013
SET-TOP BOX
Brand
ALPHASTAR
ANAM
CHANNEL MASTER
CROSSDIGITAL
CHAPARRAL
DIRECT TV
DAEWOO
DISH NETWORK SYSTEM
DISHPRO
DRAKE
DX ANTENNA
ECHOSTAR
EXPRESSVU
GOI
GE
GENERAL INSTRUMENT
HTS
HOME CABLE
HITACHI
HUGHES NETWORK
IQ
IQ PRISM
JANEIL
JERROID
JVC
Code
023
043
018 034
019
035
015 016 017 019 022 045 060
061 062 065 066 067 068
074
069 070
069
018 024 032
027
025 069 070 071
069
069
065
046 047 048 063 064
069
056
022
015 017
020
020
059
063
069 070
Brand
LG(Goldstar)
MAGNAVOX
MEMOREX
MOTOROLA
MACOM
MITSUBISHI
NEXT LEVEL
PHILIPS
PRIMESTAR
PANASONIC
PAYSAT
PROSCAN
RCA
RADIOSHACK
REALISTIC
STS
STAR TRAK
SKY
SKY LIFE
SHACK
STAR CHOICE
SONY
TOSHIBA
ULTIMATE TV
UNIDEN
ZENITH
Code
044 073
016 021 036 038 039 040 041 042
016
064
018
015
047 048 064
015 016 017 021 033 036 038 039
040 041 042 067
046 049 050 063
058 059 061 062
016
065 066
051 052 053 065 066
064
057
020 027
026
031
005 006 007
064
064
054 060
015 017 028 029 030 072
060 066
016 021 037 055 056 057
024 031 068
Continued...
English - 56
BN68-01352A-01Eng.indd 56
2007-10-06 ¿ÀÈÄ 5:52:09
SAMSUNG DVD
Product
DVD
DVDR
BD Record
VCR COMBO
VCR Record
DHR COMBO
Code
000 001 002
003 004
005 006
007 008 009 010 011
012
013
Product
Home Theater VCR COMBO
HDD Record COMBO
TWIN TRAY COMBO
STB DVD COMBO
DVD Receiver
AV Receiver
Code
014 015 016
017
018
019
020
021
DVD
Brand
ANAM
AUDIOVOX
AUDIOLOGIC
ANABA
APEX DIGITAL
AIWA
BROKSONIC
BLAUPUNKT
B&K
CURTIS MATHES
CYBER HOME
CLARION
CIRRUS
CINEVISION
DAEWOO
DENON
FARENHEIT
FISHER
GPX
GO VIDEO
GE
GREENHILL
HITACHI
HITEKER
HOYO
HARMAN / KARDON
IRT
INTEGRA
JBL
JVC
JATON
KENWOOD
KISS
KONKA
KLH
LG(Goldstar)
LOEWE
LASONIC
MOBILE AUTHORITY
MEMOREX
MALATA
MAGNAVOX
MINTEK
MONYKA
Code
030
075
085
072
070 071 074 086 083 084 088
111 112
114
062
074
122 123
027
065 077 078 079 082
080 125
081
095
066
146
067 068
090
060
061 089 133 135
069 074
074
064 113
071
073
091 110
089
092
091
022 033 115 116
073
051 108 109
073
059 100 106 107
074 075
025 031
057
058
054
055
056
076 093
074 094
073
Brand
NORCENT
NEXT BASE
NEC
NANTAUS
NESA
OPTOMEDIA ELECTRONICS
OPTIVIEW
ONKYO
PHILCO
PRINCETON
PROSCAN
PANASONIC
PHILIPS
ROTEL
RIO
RCA
RAITE
ROWA
SAMPO
SONY
SHERWOOD
SVA
SYLVANIA
SHARP
SANSUI
SANYO
SHINSONIC
SANYO
THOMSON
TOSHIBA
TECHNICS
TVIEW
TOKAI
TEAC
TECHWOOD
TREDEX
URBAN CONCEPTS
VENTURER
VOCOPRO
YAMAHA
YAMAKAWA
XWAVE
ZENITH
Code
048 049 050
052
053
144
074
105
072
076 092 119
044 045
046 047
023
024 034 124 134 136 137 138
036 076
117 118
120
023 035 074 075 131 132
073
038
104
026 029 126 127 128 129
130 141
039 041
042
043 093
140
062
062
094
090
145
028 062 076
139
072
073
096
097
098 099 101
076
075
102
032 063
040 073
103
076 121
English - 57
BN68-01352A-01Eng.indd 57
2007-10-06 ¿ÀÈÄ 5:52:09
How to assemble the Stand-Base (depending on the model)
Using the screws for securing the stand base and the monitor, firmly attach
the monitor to the stand base.
(The exterior of the set may be different from the picture.)
PS-50P96FD/
PS-63P76FD
Warning
PS-58P96FD
Firmly secure the stand to
the TV before moving it, as
the stand may fall and could
cause serious injury.
Two or more people
should carry the TV.
Never lay the TV on the
floor because of possible
damage to the screen.
Always store the TV
upright.
In case of installing your
TV on the wall, close the
cover (1) on the stand-base
connection part using two
screws for hiding.
➢
Troubleshooting
Before contacting the Samsung after-sales service, perform the following simple checks.
If you cannot solve the problem using the instructions below, note the model and serial number of
the television and contact your local dealer.
No sound or picture
 Check that the mains lead has been connected to a wall socket.
 Check that you have pressed the (Power) button (On/Off) on the front panel or press the POWER
button on the remote control.
 Check the picture contrast and brightness settings.
 Check the volume.
 Check if Internal Mute is set to ON.
Normal picture but no sound
 Check the volume.
 Check whether the volume MUTE button on the remote control has been pressed.
No picture or black and white picture
 Adjust the colour settings.
 Check that the broadcast system selected is correct.
Sound and picture interference
 Try to identify the electrical appliance that is affecting the television, then move it further away.
 Plug the television into a different main socket.
Blurred or snowy picture, distorted sound
 Check the direction, location and connections of your aerial.
This interference often occurs due to the use of an indoor aerial.
Remote control malfunctions
 Replace the remote control batteries.
 Clean the upper edge of the remote control (transmission window).
 Check that the “+” and “–” ends of the batteries are inserted correctly.
 Check that the batteries are drained.
Screen is black and power indicator light blinks steadily
 On your computer check; Power, Signal Cable.
 The TV is using its power management system.
 Move the computer’s mouse or press any key on the keyboard.
 On your equipment check (STB, DVD, etc) ; Power, Signal Cable.
 The TV is using its power management system.
 Press the Source button on the panel or remote control.
 Turn the TV off and on.
The damaged picture appears in the corner of the screen.
 If Just Scan is selected in some external devices, the damaged picture may appear in the corner of
the screen. This symptom is caused by external devices, not TV.
English - 58
BN68-01352A-01Eng.indd 58
2007-10-06 ¿ÀÈÄ 5:52:13
Specifications
The descriptions and characteristics in this booklet are given for information purposes only and
are subject to modification without notice.
Model Name
Screen Size (Diagonal)
PS-50P96FD
50 inch
PS-58P96FD
PS-63P76FD
58 inch
63 inch
PC Resolution
1920 x 1080 @ 60 Hz
Sound (Output)
15W x 2
Dimension (WxHxD)
Body
With stand
Weight
Body
With stand
Environmental Considerations
Operating Temperature
Operating Humidity
Storage Temperature
Storage Humidity
1289 x 739 x 95 mm 1465 X 838 X 100 mm 1528 x 1001 x 88 mm
1289 x 804 x 319 mm 1465 X 905 X 345 mm 1528 x 1087 x 423 mm
45 kg
53 kg
59 kg
64 kg
68 kg
89 kg
10 °C to 40 °C (50 °F to 104 °F)
10% to 80%, non-condensing
-20 °C to 45 °C (-4 °F to 113 °F)
5% to 95%, non-condensing
 This device is a Class B digital apparatus.
➢
Design and specifications are subject to change without prior notice.
 For the power supply and Power Consumption, refer to the label attached to the product.
English - 59
BN68-01352A-01Eng.indd 59
2007-10-06 ¿ÀÈÄ 5:52:45
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with
separate collection systems)
This marking shown on the product or its literature, indicates that it
should not be disposed with other household wastes at the end of its
working life.
To prevent possible harm to the environment or human health from
uncontrolled waste disposal, please separate this from other types of
wastes and recycle it responsibly to promote the sustainable reuse of
material resources.
Household users should contact either the retailer where they
purchased this product, or their local government office, for details
of where and how they can take this item for environmentally safe
recycling.
Business users should contact their supplier and check the terms and
conditions of the purchase contract. This product should not be mixed
with other commercial wastes for disposal.
BN68-01352A-01Eng.indd 61
2007-10-06 ¿ÀÈÄ 5:52:46
Contact SAMSUNG WORLD-WIDE
If you have any questions or comments relating to Samsung products, please contact the
SAMSUNG customer care centre.
Comment contacter Samsung dans le monde
Si vous avez des suggestions ou des questions concernant les produits Samsung, veuillez
contacter le Service Consommateurs Samsung.
Kontakt zu Samsung
Falls Sie Fragen oder Anregungen zu Samsung-Produkten haben, wenden Sie sich bitte an den
Samsung-Kundendienst.
Contatta SAMSUNG WORLD-WIDE
Se avete commenti o domande sui prodotti Samsung, contattate il Servizio Clienti Samsung.
Contact Samsung wereldwijd
Wanneer u suggesties of vragen heeft met betrekking tot Samsung producten, gelieve contact op te
nemen met de consumenten dienst van Samsung.
Contacte SAMSUNG GLOBAL
Se tem algumas dúvidas ou comentários sobre os produtos Samsung, contacte por favor a nossa
linha de apoio a clientes Samsung.
Obrnite se na SAMSUNG WORLD WIDE (GLOBALNI SAMSUNG)
V primeru vprašanj ali pripomb v zvezi z izdelki Samsung se obrnite na center za pomoč strankam
SAMSUNG.
Contacte con SAMSUNG WORLD-WIDE
Si tiene alguna pregunta o comentario referente a nuestros productos, por favor contacte con
nuestro Servicio de Atención al Cliente.
Contact SAMSUNG WORLD-WIDE_8Langa(¼­±¸).indd 2
2007-10-06 ¿ÀÈÄ 6:03:38
Country
AUSTRIA
BELGIUM
Web Site
Customer Care Centre 
0800-SAMSUNG(726-7864)
www.samsung.com/at
0032 (0)2 201 24 18
www.samsung.com/be
844 000 844
www.samsung.com/cz
CZECH REPUBLIC
Distributor pro Českou republiku:
Samsung Zrt., česka organizační složka Vyskočilova 4, 14000 Praha 4
DENMARK
70 70 19 70
www.samsung.com/dk
FINLAND
030-6227 515
www.samsung.com/fi
3260 SAMSUNG(726-7864)
FRANCE
www.samsung.com/fr
08 25 08 65 65 (€ 0,15/Min)
GERMANY
01805 - 121213 (€ 0,14/Min)
www.samsung.de
06-80-SAMSUNG(726-7864)
www.samsung.com/hu
HUNGARY
800-SAMSUNG(726-7864)
www.samsung.com/it
ITALIA
LUXEMBURG
0035 (0)2 261 03 710
www.samsung.com/be
NETHERLANDS
0900 20 200 88 (€ 0,10/Min)
www.samsung.com/nl
NORWAY
815-56 480
www.samsung.com/no
0 801 801 881
POLAND
www.samsung.com/pl
022-607-93-33
80 8 200 128
www.samsung.com/pt
PORTUGAL
REPUBLIC OF IRELAND 0818 717 100
www.samsung.com/ie
0800-SAMSUNG(726-7864)
www.samsung.com/sk
SLOVAKIA
SPAIN
902 10 11 30
www.samsung.com/es
SWEDEN
0771-400 200
www.samsung.com/se
SWITZERLAND
0800-SAMSUNG(726-7864)
www.samsung.com/ch
U.K
0870-SAMSUNG(726-7864)
www.samsung.com/uk
ESTONIA
800-7267
www.samsung.ee
8-10-800-500-55-500
www.samsung.kz
KAZAHSTAN
00-800-500-55-500
KYRGYZSTAN
LATVIA
800-7267
www.samsung.com/lv
LITHUANIA
8-800-77777
www.samsung.lt
RUSSIA
8-800-555-55-55
www.samsung.ru
UKRAINE
8-800-502-0000
www.samsung.ua
8-800-120-0-400
www.samsung.uz
UZBEKISTAN
Contact SAMSUNG WORLD-WIDE_8Langa(¼­±¸).indd 3
2007-10-06 ¿ÀÈÄ 6:03:38
Download PDF

advertising