KC9024 | Black&Decker KC9024 SCREWDRIVER instruction manual

KC9024FB
1
Copyright Black & Decker
2
5
3
4
2
1
A
6
2
B
3
3
7
C
1
D
8
E
4
ENGLISH
CORDLESS SCREWDRIVER KC9024FB
CONGRATULATIONS!
You have chosen a Black & Decker tool. Our aim is
to provide quality tools at an affordable price.
We hope that you will enjoy using this tool for
many years.
EC DECLARATION OF CONFORMITY
KC9024FB
Black & Decker declares that these tools
conform to:
98/37/EC, 89/336/EEC, 73/23/EEC,
EN 50260, EN 55014-1, EN 55014-2,
EN 61000-3-2, EN 61000-3-3, EN 60335
Level of sound pressure, measured according to
EN 50260:
INTENDED USE
Your Black & Decker screwdriver KC9024FB has
been designed for inserting and removing screws
and nuts using the appropriate accessories.
This tool is intended for consumer use only.
Your Black & Decker charger has been designed
for charging the battery in the tool with which it
was supplied.
SAFETY INSTRUCTIONS
Warning symbols
The following symbols are used in this manual:
Denotes risk of personal injury, loss of life
or damage to the tool in case of nonobservance of the instructions in this
manual.
KC9024FB
LpA (sound pressure)
dB(A)
70
LWA (acoustic power)
dB(A)
85
Hand/arm weighted vibration value according to
EN 50260:
Denotes risk of electric shock.
Read the manual prior to operation.
KC9024FB
< 2.5 m/s2
Fire hazard.
Know your tool
◆
Colin Wills
Director of Engineering
BDCI, 4/F, 2 Dai Wang Street
Tai Po Industrial Estate
Tai Po NT, Hong Kong
◆
◆
◆
Warning! When using battery-powered
tools, basic safety precautions,
including the following, should always
be followed to reduce the risk of fire,
leaking batteries, personal injury and
material damage.
Read all of this manual carefully before
operating the tool.
Before operating the tool, make sure
that you know how to switch the tool off
in an emergency.
Retain this manual for future reference.
5
ENGLISH
General
1. Keep work area clean
Cluttered areas and benches can cause
accidents.
2. Consider work area environment
Do not expose the tool to rain. Do not use the
tool in damp or wet conditions. Keep the work
area well lit. Do not use the tool where there is
a risk of causing fire or explosion, e.g. in the
presence of flammable liquids and gases.
3. Keep children away
Do not allow children, visitors or animals to
come near the work area or to touch the tool.
4. Dress properly
Do not wear loose clothing or jewellery,
as these can be caught in moving parts.
Preferably wear rubber gloves and non-slip
footwear when working outdoors. Wear
protective hair covering to keep long hair out
of the way.
5. Personal protection
Always use safety glasses. Use a face or dust
mask whenever the operations may produce
dust or flying particles. Wear ear protection
whenever the sound level seems
uncomfortable.
6. Do not overreach
Keep proper footing and balance at all times.
7. Stay alert
Watch what you are doing. Use common sense.
Do not operate the tool when you are tired.
8. Secure workpiece
Use clamps or a vice to hold the workpiece.
It is safer and it frees both hands to operate
the tool.
9. Connect dust extraction equipment
If devices are provided for the connection of
dust extraction and collection facilities, ensure
that these are connected and properly used.
10. Remove keys and adjusting wrenches
Always check that keys and adjusting wrenches
are removed from the tool before operating
the tool.
11. Use appropriate tool
The intended use is described in this
instruction manual. Do not force small tools or
attachments to do the job of a heavy-duty tool.
6
The tool will do the job better and safer at the
rate for which it was intended. Do not force the
tool.
Warning! The use of any accessory or
attachment or performance of any operation
with this tool other than those recommended
in this instruction manual may present a risk of
personal injury.
12. Check for damaged parts
Before use, carefully check the tool for damage.
Check for misalignment and seizure of moving
parts, breakage of parts, damage to guards
and switches and any other conditions that
may affect its operation. Ensure that the tool
will operate properly and perform its intended
function. Do not use the tool if any part is
damaged or defective. Do not use the tool if
the switch does not turn it on and off.
Have any damaged or defective parts repaired
or replaced by an authorised repair agent.
Never attempt any repairs yourself.
13. Avoid unintentional starting
Do not carry the tool with a finger on the
on/off switch.
14. Do not abuse cord
Never carry the charger by its cord or pull it to
disconnect from the socket. Keep the cord
away from heat, oil and sharp edges.
15. Store idle tools
When not in use, tools, batteries and chargers
should be stored in a dry, locked up or high
place, out of reach of children.
16. Maintain tools with care
Keep cutting tools sharp and clean for better
and safer performance. Follow the instructions
for maintenance and changing accessories.
Keep handles and switches dry, clean and free
from oil and grease.
17. Repairs
This tool complies with relevant safety
requirements. Repairs should only be carried
out by qualified persons using original spare
parts; otherwise this may result in considerable
danger to the user.
ENGLISH
Additional safety instructions for batteries and
chargers
Batteries
◆ Never attempt to open for any reason.
◆ Do not store in locations where the
temperature may exceed 40 °C.
◆ Charge only at ambient temperatures between
4 °C and 40 °C.
◆ Charge only using the charger provided with
the tool (see technical data).
◆ When disposing of batteries, follow the
instructions given in the section “Protecting
the environment”.
◆ Under extreme conditions, battery leakage
may occur. When you notice liquid on the
battery, proceed as follows:
- Carefully wipe the liquid off using a cloth.
Avoid skin contact.
- In case of skin or eye contact, follow the
instructions below.
The battery fluid, a 25-30% solution of
potassium hydroxide, can be harmful.
In case of skin contact, immediately rinse
with water. Neutralise with a mild acid such
as lemon juice or vinegar. In case of eye
contact, rinse abundantly with clean water
for at least 10 minutes. Consult a physician.
Fire hazard! Avoid short-circuiting the
contacts of a detached battery.
Do not incinerate the battery.
Chargers
◆ Use your Black & Decker charger only to
charge the battery in the tool with which it was
supplied. Other batteries could burst, causing
personal injury and damage.
◆ Never attempt to charge non-rechargeable
batteries.
◆ Have defective cords replaced immediately.
◆ Do not expose to water.
◆ Do not open the charger.
◆
Do not probe the charger.
The charger is intended for indoor use
only.
ELECTRICAL SAFETY
Your charger has been designed for a specific
mains voltage. Always check that the mains voltage
corresponds to the voltage on the rating plate.
Your charger is double insulated in
accordance with EN 60335; therefore no
earth wire is required.
Never attempt to replace the charger unit
with a regular mains plug.
PACKAGE CONTENTS
The pack contains:
1 Cordless screwdriver
1 Double-ended screwdriver bit
1 Charger
1 Instruction manual
◆
◆
1.
2.
3.
4.
5.
Carefully unpack all parts.
Please note that additional items may be found
in the carton, depending on the letter suffix
following the catalogue number of your tool.
OVERVIEW (fig. A)
On/off switch with forward/reverse function
Bit holder
Charger connector
Charger
Battery
ASSEMBLY
Fitting and removing a screwdriver bit (fig. B)
◆ To fit a screwdriver bit (6), push it into the bit
holder (2) until it locates.
◆ To remove a screwdriver bit, pull it straight
from the bit holder.
USE
Let the tool work at its own pace.
Do not overload.
7
ENGLISH
Charging the battery (fig. C)
The battery needs to be charged before first use
and whenever it fails to produce sufficient power
on jobs that were easily done before.
When charging the battery for the first time,
or after prolonged storage, it will only accept an
80% charge. After several charge and discharge
cycles, the battery will attain full capacity.
The battery may become warm while charging;
this is normal and does not indicate a problem.
Do not charge the battery at ambient
temperatures below 4 °C or above 40 °C.
Recommended charging temperature:
approx. 24 °C.
To charge the battery, insert the charger plug
(7) into the connector (3).
◆ Plug in the charger.Switch on at the mains.
◆ Leave the tool connected to the charger for at
least 12 hours.
The tool can be left connected to the charger
indefinitely. The charger may hum and become
warm while charging; this is normal and does not
indicate a problem.
◆ Before using the tool, unplug the charger and
disconnect the tool from the charger.
◆
◆
◆
When screwing in wood, it is recommended to
drill a pilot hole with a depth equal to the
length of the screw. A pilot hole guides the
screw and prevents splintering or distortion of
the wood. For the optimum size of the pilot
hole, refer to the table below.
When screwing in hardwood, also drill a
clearance hole with a depth equal to half the
length of the screw. For the optimum size of
the clearance hole, refer to the table below.
Screw size
Pilot hole ø
(softwood)
Pilot hole ø
(hardwood)
Clearance hole
No. 8
(4 mm)
No. 10
(6 mm)
2 mm
3.2 mm
3.5 mm
2.5 mm
4 mm
3.5 mm
5.0 mm
4.0 mm
5.7 mm
MAINTENANCE
Your Black & Decker tool has been designed to
operate over a long period of time with a
minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and
regular cleaning.
Your charger does not require any maintenance
apart from regular cleaning.
Do not use the tool while it is connected
to the charger.
Operating the tool (fig. D)
◆ To tighten a screw or nut, slide the on/off
switch (1) to the right and press it.
◆ To loosen a screw or nut, slide the on/off
switch (1) to the left and press it.
◆ To switch the tool off, release the on/off switch.
No. 6
(3.5 mm)
Unplug the charger before cleaning it.
◆
◆
Regularly clean the ventilation slots in your tool
using a soft brush or dry cloth.
Regularly clean the motor housing using a
damp cloth. Do not use any abrasive or
solvent-based cleaner.
PROTECTING THE ENVIRONMENT
Hints for optimum use
◆ Always use the correct type and size of
screwdriver bit.
◆ If screws are difficult to tighten, try applying a
small amount of washing liquid or soap as a
lubricant.
◆ Use the spindle lock to loosen very tight
screws or to firmly tighten screws.
◆ Always hold the tool and screwdriver bit in a
straight line with the screw.
8
Tools
Should you find one day that your tool
needs replacement, or if it is of no further
use to you, think of the protection of the
environment. Black & Decker repair agents
will accept old Black & Decker tools and
ensure that they are disposed of in an
environmentally safe way.
ENGLISH
Battery (fig. E)
Cd
If you want to dispose of the tool yourself,
the battery must be removed as described
below and disposed of in accordance with
local regulations.
Do not short-circuit the battery terminals.
Do not use tools to remove the battery;
only use your fingers.
◆
◆
◆
◆
◆
◆
If possible, operate the tool to run the battery
down completely.
Use a screwdriver to remove the clip (8).
Pull the front part off the tool.
Lift the batteries out of the tool.
Disconnect the wires from the battery terminals.
Place the battery in a suitable packaging to
ensure that the terminals cannot be shortcircuited. Take the battery to your service agent
or a local recycling station. Collected batteries
will be recycled or disposed of properly.
Technical data
Voltage
No-load speed
Max. torque
Bit holder
Weight
Charger
Input voltage
Approx. charging time
Weight
The product has not been subjected to misuse
or neglect.
◆ The product has not sustained any damage
through foreign objects, substances or accidents.
◆ Repairs have not been attempted by anyone
other than our service staff or authorised repair
agents.
This guarantee is offered as an extra benefit and
does not affect your statutory rights.
◆
KC9024FB
VDC 2.4
min-1 150
Nm 2.45
6.35 mm hex
kg 0.26
VAC 230
h 12
kg 0.14
GUARANTEE (UK, SOUTH AFRICA,
AUSTRALIA AND NEW ZEALAND ONLY)
Should your Black & Decker product become
defective due to faulty materials or workmanship,
within 24 months from the date of purchase, we
guarantee to either replace all defective parts or -at
our discretion- to replace the unit free of charge,
provided that:
◆ The product is returned to us or one of our
authorised repair agents with proof of purchase.
◆ The product has not been used for trade,
professional or hire purposes.
AFTER SALES SERVICE
(UK, SOUTH AFRICA, AUSTRALIA
AND NEW ZEALAND ONLY)
Black & Decker offers a nationwide network of
authorised repair agents. The use of other than
genuine Black & Decker parts and accessories may
reduce the performance of the tool and cause
personal injury and material damage. The terms
and conditions of the warranty could also be
rendered void.
OUR AFTER SALES SERVICE POLICY
(UK, AUSTRALIA AND NEW ZEALAND
ONLY)
Full details on our after-sales service are available
on the Internet at www.2helpU.com.
Alternatively, contact our Service and Information
Centre at the address towards the back of this
manual.
It is our aim that all Black & Decker customers
should be totally satisfied with their
Black & Decker product and our after sales service.
If any help or advice is needed, please contact
your local Black & Decker repair agent.
If your product needs repair, please take or send it
to an authorised repair agent, providing proof of
purchase if claiming a guarantee repair.
9
Australia
DEWALT Industrial Power Tool Company
7 Clarice Road
Box Hill, Victoria 3128
Tel. 03 9895 9200
Fax 03 9899 7465
New Zealand
Black & Decker
81 Hugo Johnson Drive
Penrose, Auckland, New Zealand
Tel. 09 579 7600
Fax 09 579 8200
South Africa
Black & Decker South Africa (Pty) Ltd
Physical address:
146 Lechwe Street
Corporate park
Randjiesfontein, Midrand
Postal address:
Postnet Suite 107, Private Bag X65
Halfway House 1685
Tel. (011) 653-1400
Fax (011) 653-1499
United Kingdom
Black & Decker
210 Bath Road
Slough, Berkshire SL1 3YD
Tel. 01753 511234
Fax 01753 551155
Helpline 01753 574277
10
497802-06
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
Yes
No
Was this tool your first purchase?
Yes
No
Was this tool a gift?
Postal code: .............................................................................................
Town: .......................................................................................................
Address: ...................................................................................................
Name: ......................................................................................................
○
Dealer address
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
Data protection act:
Tick the box if you prefer not to receive further information.
Dealer address: ........................................................................................
.................................................................................................................
.................................................................................................................
Yes
No
Was this tool bought as a replacement?
○
Date of purchase
○
✁
11
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
GUARANTEE CARD
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
✁
Please complete this section immediately after the purchase of your tool and send it to Black & Decker in your
country. If you live in Australia or New Zealand, please register by using the alternative guarantee card
supplied.
12
497802-06
○
○
○
○
○
Download PDF