KR550CRE | Black&Decker KR550CRE DRILL Type 4 instruction manual

5
yy
;;
ÀÀ
@@
€€
;;
€€
ÀÀ
@@
@@yy
€€
ÀÀ
;;
yy
yy
ÀÀ
;;
@@
€€
@@
€€
ÀÀ
;;
yy
;;
yy
@@ yy
€€
ÀÀ
;;
ÀÀ
@@
€€
@@
€€
ÀÀ
;;
yy
;;
yy
@@
€€
ÀÀ
9
6
7
4
3
8
1
2
@
€
À
;
y
yy
@@
€€
ÀÀ
;;
@
€
À
;
@ y
€
À
;
y
@@
€€
ÀÀ
;;
@@yy
€€
ÀÀ
;;
yy
yy
@@
€€
ÀÀ
;;
@
€
À
;
y
@
€
À
;
y
@@
€€
ÀÀ
;;
yy
@@
€€
ÀÀ
;;
yy
@@
€€
ÀÀ
;;
yy
@@
€€
ÀÀ
;;
yy
yy
@@
€€
ÀÀ
;;
y;@
@@
€€
ÀÀ
;;
yy
@@
€€
ÀÀ
;;
yy
y;@
@@
€€
ÀÀ
;;
yy
UK
Ireland
Australia
New Zealand
1
y
;
@
€
À
yyy;@
ÀÀ
€€
@@
;;
yyy;@
ÀÀ
€€
@@
;;
@@
€€
ÀÀ
;;
yy
9
11
4
B
3
11
10
A
C
15
11
17
16
D
2
14
E
12
;@€Ày
13
Intended use
Your Black & Decker drill has been designed for drilling in
wood, metal, plastics and masonry as well as for screwdriving
purposes. This tool is intended for consumer use only.
Safety instructions
Warning! When using mains-powered tools, basic safety
precautions, including the following, should always be
followed to reduce the risk of fire, electric shock,
personal injury and material damage.
◆ Read all of this manual carefully before operating the tool.
◆ Retain this manual for future reference.
◆ Remove the plug from the socket before carrying out any
adjustment, servicing or maintenance.
Keep work area clean
Cluttered areas and benches can cause accidents.
Consider work area environment
Do not expose the tool to rain. Do not use the tool in damp or
wet conditions. Keep the work area well lit. Do not use the
tool where there is a risk of causing fire or explosion, e.g. in
the presence of flammable liquids and gases.
Keep children away
Do not allow children, visitors or animals to come near the
work area or to touch the tool or mains cable.
Dress properly
Do not wear loose clothing or jewellery, as these can be
caught in moving parts. Preferably wear rubber gloves and
non-slip footwear when working outdoors. Wear protective
hair covering to keep long hair out of the way.
Personal protection
Always use safety glasses. Use a face or dust mask whenever
the operations may produce dust or flying particles.
Hearing protection should be worn.
Guard against electric shock
Prevent body contact with earthed or grounded surfaces
(e.g. pipes, radiators, cookers and refrigerators). Electric safety
can be further improved by using a high-sensitivity
(30mA/30 mS) residual current device (RCD).
Do not overreach
Keep proper footing and balance at all times.
Stay alert
Watch what you are doing. Use common sense. Do not operate
the tool when you are unconcentrated.
Secure workpiece
Use clamps or a vice to hold the workpiece. It is safer and it
frees both hands to operate the tool.
Connect dust extraction equipment
If devices are provided for the connection of dust extraction
and collection facilities, ensure that these are connected and
properly used.
◆
Remove keys and adjusting wrenches
Always check that keys and adjusting wrenches are removed
from the tool before operating the tool.
Extension cables
Before use, inspect the extension cable and replace if
damaged. When using the tool outdoors, only use extension
cables intended for outdoor use. Up to 30 m of Black & Decker
extension cable can be used without loss of power.
Use appropriate tool
The intended use is described in this instruction manual.
Do not force small tools or attachments to do the job of a
heavy-duty tool. The tool will do the job better and safer at the
rate for which it was intended. Do not force the tool.
Warning! The use of any accessory or attachment or performance
of any operation with this tool other than those recommended
in this instruction manual may present a risk of personal injury.
Check for damaged parts
Before use, carefully check the tool and mains cable for
damage. Check for misalignment and seizure of moving parts,
breakage of parts, damage to guards and switches and any
other conditions that may affect its operation. Ensure that the
tool will operate properly and perform its intended function.
Do not use the tool if any part is damaged or defective. Do not
use the tool if the switch does not turn it on and off. Have any
damaged or defective parts repaired or replaced by an
authorised repair agent. Never attempt any repairs yourself.
Unplug the tool
Unplug the tool when it is not in use, before changing any parts
of the tool, accessories or attachments and before servicing.
Avoid unintentional starting
Do not carry the tool with a finger on the on/off switch.
Be sure that the tool is switched off when plugging in.
Do not abuse cord
Never carry the tool by its cord or pull it to disconnect from the
socket. Keep the cord away from heat, oil and sharp edges.
Store idle tools
When not in use, tools should be stored in a dry, locked up or
high place, out of reach of children.
Maintain tools with care
Keep cutting tools sharp and clean for better and safer
performance. Follow the instructions for maintenance and
changing accessories. Keep handles and switches dry, clean
and free from oil and grease.
Repairs
This tool complies with relevant safety requirements. Repairs
should only be carried out by qualified persons using original
spare parts; otherwise this may result in considerable danger
to the user.
Electrical safety
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
3
Additional safety instructions for Australia and
New Zealand
◆ This appliance is not intended for use by young or infirm
persons without supervision. Children must be supervised
to ensure they do not play with the appliance.
◆ If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Features
This tool includes some or all of the following features.
1. Variable speed switch
2. Lock-on button
3. Side handle
4. Depth stop
5. Chuck
6. Drilling mode selector
7. Forward/reverse switch
8. Variable speed control knob
9. Spindle lock button
Assembly
Removing and refitting the chuck (fig. E)
◆ Open the chuck as far as possible.
◆ Remove the chuck retaining screw by turning it clockwise
using a screwdriver.
◆ Tighten an Allen key (17) into the chuck and strike it with
a hammer as shown.
◆ Remove the Allen key.
◆ Remove the chuck by turning it counterclockwise.
◆ To refit the chuck, screw it onto the spindle and secure it
with the chuck retaining screw.
Use
Warning! Before drilling into walls, floors or ceilings,
check for the location of wiring and pipes.
Selecting the direction of rotation
◆ For drilling and for tightening screws, slide the forward/
reverse switch (7) forward.
◆ For loosening screws or removing a jammed drill bit, slide
the forward/reverse switch (7) backward.
Warning! Never change the direction of rotation while the
motor is running.
Warning! Make sure that the tool is switched off and unplugged.
Fitting the side handle and depth stop (fig. A)
◆ Turn the grip (10) counterclockwise until you can slide the
side handle (3) onto the front of the tool as shown.
◆ Rotate the side handle into the desired position.
◆ Insert the depth stop (4) into the mounting hole as shown.
◆ Set the depth stop to the desired position. The maximum
drilling depth is equal to the distance between the tip of
the drill bit and the front end of the depth stop.
◆ Tighten the side handle by turning the grip clockwise.
Fitting a drill bit or screwdriver bit
Keyless chuck with spindle lock (fig. B)
◆ Keep the spindle lock button (9) depressed and open the
chuck.
◆ Insert the bit shaft (11) into the chuck and firmly tighten
the chuck.
Keyless chuck (fig. C)
◆ Open the chuck by turning the front part (12) with one
hand while holding the rear part (13) with the other.
◆ Insert the bit shaft (11) into the chuck and firmly tighten
the chuck.
Keyed chuck (fig. D)
◆ Open the chuck by turning the sleeve (14).
◆ Insert the bit shaft (11) into the chuck.
◆ Insert the chuck key (15) into each hole (16) in the side of
the chuck and turn until tight.
4
Selecting the drilling mode
◆ For drilling in masonry, set the drilling mode selector (6) to
the position.
◆ For drilling in other materials and for screwdriving, set the
drilling mode selector (6) to the position.
Switching on and off
◆ To switch the tool on, press the variable speed switch (1).
The tool speed depends on how far you press the switch.
If the tool has a variable speed control knob (8), set it to
the required speed range. As a general rule, use low
speeds for large diameter drill bits and high speeds for
smaller diameter drill bits.
◆ For continuous operation, press the lock-on button (2) and
release the variable speed switch. This option is available
only at full speed.
◆ To switch the tool off, release the variable speed switch.
To switch the tool off when in continuous operation, press
the variable speed switch once more and release it.
Accessories
The performance of your tool depends on the accessory used.
Black & Decker and Piranha accessories are engineered to high
quality standards and designed to enhance the performance of
your tool. By using these accessories you will get the very best
from your tool.
Maintenance
Guarantee
Your tool has been designed to operate over a long period of
time with a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular cleaning.
Black & Decker is confident of the quality of its products and
offers an outstanding guarantee. This guarantee statement is
in addition to and in no way prejudices your statutory rights.
The guarantee is valid within the territories of the Member
States of the European Union and the European Free Trade
Area.
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
◆ Safely dispose of the old plug.
◆ Connect the brown lead to the live terminal in the new plug.
◆ Connect the blue lead to the neutral terminal.
Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality
plugs. Recommended fuse: 5 A.
Protecting the environment
Black & Decker provides a facility for recycling
Black & Decker products once they have reached the
end of their working life. This service is provided
free of charge. To take advantage of this service
please return your product to any authorised repair
agent who will collect them on our behalf.
You can check the location of your nearest authorised repair
agent by contacting your local Black & Decker office at the
address indicated in this manual. Alternatively, a list of
authorised Black & Decker repair agents and full details of our
after-sales service and contacts are available on the Internet
at: www.2helpU.com.
Technical data
Power input
No-load speed
KR550
W 550
min-1 0-2,800
Max. drilling capacity
Steel/concrete
Wood
KR600
600
0-3,000
If a Black & Decker product becomes defective due to faulty
materials, workmanship or lack of conformity, within 24 months
from the date of purchase, Black & Decker guarantees to
replace defective parts, repair products subjected to fair wear
and tear or replace such products to ensure minimum
inconvenience to the customer unless:
◆ The product has been used for trade, professional or hire
purposes;
◆ The product has been subjected to misuse or neglect;
◆ The product has sustained damage through foreign
objects, substances or accidents;
◆ Repairs have been attempted by persons other than
authorised repair agents or Black & Decker service staff.
To claim on the guarantee, you will need to submit proof of
purchase to the seller or an authorised repair agent. You can
check the location of your nearest authorised repair agent by
contacting your local Black & Decker office at the address
indicated in this manual. Alternatively, a list of authorised
Black & Decker repair agents and full details of our after-sales
service and contacts are available on the Internet at:
www.2helpU.com.
KR650 KR700
650
700
0-3,000 0-3,000
mm
mm
13
25
EC declaration of conformity
Black & Decker declares that these products conform to:
98/37/EC, 89/336/EEC, 73/23/EEC, EN 50144, EN 55014,
EN 61000
LpA (sound pressure): 99 dB(A), LWA (acoustic power) 112 dB(A),
hand/arm weighted vibration 8.9 m/s2
Kevin Hewitt
Director of Consumer Engineering
Spennymoor, County Durham DL16 6JG,
United Kingdom
Australia
DEWALT Industrial Power Tool Company
7 Clarice Road
Tel. 03 9895 9200
Box Hill, Victoria 3128
Fax 03 9899 7465
New Zealand
Black & Decker
Tel. 09 579 7600
81 Hugo Johnson Drive
Fax 09 579 8200
Penrose, Auckland, New Zealand
United Kingdom
Black & Decker
210 Bath Road
Slough, Berkshire SL1 3YD
Tel. 01753 511234
Fax 01753 551155
Helpline 01753 574277
5
KR550CRE - KR572 - KR580CRE
KR600RE - KR600CRE - KR650CRF - KR650CRE
KR650RE - KR700RE - KR700CRE
TYP.
3-4
104
104
104
123
122
125
123
120V
240V
KR572
126
127
121
KR700
124
128
129
103
101
125
143
115
116
102
107 108
CRE
KR650-700
110
111
112 113
114
121
114
133
CRE
145
CRE
RE
146
133
138
120
134
139
132
103
140
135
KR700
OTHERS
129
105
129
119
TYPE 2
E12545 / 374224-00
6
141
105
129
105
119
KR572
128
128
119
TYPE 2
www.2helpu.com
03 - 01 - 2002
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
Yes
No
Was this tool your first purchase?
Yes
No
Was this tool a gift?
Postal code: ..........................................................................................................................
Town: ....................................................................................................................................
Address: ................................................................................................................................
Name: ...................................................................................................................................
○
Dealer address
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
Data protection act:
Tick the box if you prefer not to receive further information.
Dealer address: ....................................................................................................................
..............................................................................................................................................
..............................................................................................................................................
Yes
No
Was this tool bought as a replacement?
○
Date of purchase
○
✁
7
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
GUARANTEE CARD
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
✁
Please complete this section immediately after the purchase of your tool and send it to Black & Decker in your country.
If you live in Australia or New Zealand, please register by using the alternative guarantee card supplied.
8
579628-01
○
○
○
○
○
Download PDF