KR60 | Black&Decker KR60 HAMMER DRILL instruction manual

www.blackanddecker.com
4
5
6
3
2
1
7
8
9
UK
Ireland
Australia
New Zealand
1
8
7
12
13
10
A
B
6
14 15
18
D
16 15 17
C
2
11
Intended use
Your Black & Decker hammer drill has been designed for drilling
in wood, metal, plastics, and masonry as well as for screwdriving
purposes. This tool is intended for consumer use only.
General safety rules
Warning! Read all instructions. Failure to follow all instructions
listed below may result in electric shock, fire and/or serious
injury. The term “power tool” in all of the warnings listed
below refers to your mains operated (corded) power tool or
battery operated (cordless) power tool.
SAVE THESE INSTRUCTIONS.
1. Work area
a. Keep work area clean and well lit. Cluttered and dark
areas invite accidents.
b. Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases
or dust. Power tools create sparks which may ignite the
dust or fumes.
c. Keep children and bystanders away while
operating a power tool. Distractions can cause you to
lose control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs
with earthed (grounded) power tools. Unmodified
plugs and matching outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock
if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase the
risk of electric shock.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a
power tool while you are tired or under the influence
of drugs, alcohol or medication. A moment of
inattention while operating power tools may result in
serious personal injury.
b. Use safety equipment. Always wear eye protection.
Safety equipment such as dust mask, non-skid safety
shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
c. Avoid accidental starting. Ensure the switch is in
the off position before plugging in. Carrying power
tools with your finger on the switch or plugging in power
tools that have the switch on invites accidents.
d. Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power tool
in unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these
are connected and properly used. Use of these
devices can reduce dust related hazards.
4. Power tool use and care
a. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will do
the job better and safer at the rate for which it was designed.
b. Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source before
making any adjustments, changing accessories, or
storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users.
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to
bind and are easier to control.
g. Use the power tool, accessories and tool bits etc.,
in accordance with these instructions and in the
manner intended for the particular type of power
tool, taking into account the working conditions
and the work to be performed.
3
Use of the power tool for operations different from those
intended could result in a hazardous situation.
5. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Additional safety instructions for impact drills
◆ Wear ear protectors with impact drills. Exposure to
noise can cause hearing loss.
◆ Use auxiliary handles supplied with the tool. Loss of
control can cause personal injury.
Electrical safety
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
◆
◆
This appliance is not intended for use by young or infirm
persons without supervision. Children must be supervised
to ensure they do not play with the appliance.
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Features
This tool includes some or all of the following features.
1. Variable speed switch
2. Lock-on button
3. Forward/reverse slider
4. Levelok™ straight drilling indicator
5. Drilling mode selector
6. Keyless chuck (KR60(L)/KR70(L))
Quick Connect™ chuck (KR60QC/KR70QC)
7. Depth stop
8. Side handle
9. Bit storage
Assembly
Warning! Make sure that the tool is switched off and unplugged.
Fitting the side handle and depth stop (fig. A)
◆ Turn the grip (10) counterclockwise until you can slide the
side handle (8) onto the front of the tool as shown.
◆ Rotate the side handle into the desired position.
◆ Insert the depth stop (7) into the mounting hole as shown.
◆ Set the depth stop to the desired position. The maximum
drilling depth is equal to the distance between the tip of
the drill bit and the front end of the depth stop.
◆ Tighten the side handle by turning the grip clockwise.
4
Fitting a drill bit or screwdriver bit
KR60(L)/KR70(L) - Keyless chuck (fig. B)
◆ Open the chuck by turning the front part (12) with one
hand while holding the rear part (11) with the other.
◆ Insert the bit shaft (13) into the chuck and firmly tighten
the chuck.
KR60QC/KR70QC - Quick Connect™ chuck (fig. B & C)
The chuck on these models can be easily removed and refitted.
When your project entails both drilling and screwdriving,
fit a screwdriver bit in the spindle and a drill bit in the chuck:
you will then only need to remove the chuck for screwdriving
and refit it for drilling. The screwdriver bit can be left in the
spindle while drilling. You can also fit drill bits with a
hexagonal shaft in this way.
◆ To fit a drill bit, proceed as described above.
◆ To fit a screwdriver bit, proceed as follows:
◆ Remove the chuck (6).
◆ Install a screwdriver bit (16) by pushing it into the spindle
(15) as shown.
◆ To remove the screwdriver bit, pull the ring (17) back and
pull the screwdriver bit out of the spindle.
Removing and refitting the chuck
KR60(L)/KR70(L) - Keyless chuck (fig. D)
◆ Open the chuck as far as possible.
◆ Remove the chuck retaining screw, located in the front
part of the chuck, by turning it clockwise using a
screwdriver.
◆ Tighten an Allen key (18) into the chuck and strike it with
a hammer as shown.
◆ Remove the Allen key.
◆ Remove the chuck by turning it counterclockwise.
◆ To refit the chuck, screw it onto the spindle and secure it
with the chuck retaining screw.
KR60QC/KR70QC - Quick Connect™ chuck (fig. C)
◆ To remove the chuck (6), keep the release tabs (14)
depressed and pull the chuck off the spindle (15).
◆ To refit the chuck, push it onto the spindle until it is firmly
locked into place.
Warning! Always make sure that the chuck is securely fitted.
Use
Warning! Before drilling into walls, floors or ceilings,
check for the location of wiring and pipes.
Selecting the direction of rotation
For drilling and for tightening screws, use forward (clockwise)
rotation. For loosening screws or removing a jammed drill bit,
use reverse (counterclockwise) rotation.
◆ To select forward rotation, push the forward/reverse
slider (3) to the left.
◆ To select reverse rotation, push the forward/reverse slider
to the right.
Warning! Never change the direction of rotation while the
motor is running.
Selecting the drilling mode
◆ For drilling in masonry, set the drilling mode selector (5) to
the position.
◆ For drilling in other materials and for screwdriving, set the
drilling mode selector (5) to the position.
KR60L/KR70L - Levelok™ straight drilling indicator
This tool is fitted with an indicator to facilitate straight
drilling. This feature can be used both in horizontal and in
vertical position. The indicator is activated while the tool is
connected to the mains.
◆ Position the tool as required.
◆ Slowly move the rear of the tool until the red indicator (4)
lights up and remains on.
Switching on and off
◆ To switch the tool on, press the variable speed switch (1).
The tool speed depends on how far you press the switch.
As a general rule, use low speeds for large diameter drill
bits and high speeds for smaller diameter drill bits.
◆ For continuous operation, press the lock-on button (2) and
release the variable speed switch. This option is available
only at full speed.
◆ To switch the tool off, release the variable speed switch.
To switch the tool off when in continuous operation,
press the variable speed switch once more and release it.
Accessories
The performance of your tool depends on the accessory used.
Black & Decker and Piranha accessories are engineered to
high quality standards and designed to enhance the
performance of your tool. By using these accessories you will
get the very best from your tool.
Maintenance
◆
To clean the tool, use only mild soap and a damp cloth.
Never let any liquid get inside the tool and never immerse
any part of the tool into liquid.
Protecting the environment
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your Black & Decker product
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product
available for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again. Reuse of recycled materials helps prevent
environmental pollution and reduces the demand for
raw materials.
Local regulations may provide for separate collection of
electrical products from the household, at municipal waste
sites or by the retailer when you purchase a new product.
Black & Decker provides a facility for the collection and
recycling of Black & Decker products once they have reached
the end of their working life. To take advantage of this service
please return your product to any authorised repair agent who
will collect them on our behalf.
You can check the location of your nearest authorised repair
agent by contacting your local Black & Decker office at the
address indicated in this manual. Alternatively, a list of
authorised Black & Decker repair agents and full details of our
after-sales service and contacts are available on the Internet
at: www.2helpU.com
Technical data
Voltage
Power input
No-load speed
Weight
Max drilling capacity
Steel/concrete
Wood
VAC
W
min-1
kg
KR60
230
600
0-3,000
2.3
mm 13
mm 25
KR70
230
730
0-3,000
2.3
13
25
Your tool has been designed to operate over a long period of
time with a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular cleaning.
◆ Regularly clean the ventilation slots with a clean, dry
paint brush.
5
EC declaration of conformity
KR60/KR70
Black & Decker declares that these products conform to:
98/37/EC, 89/336/EEC, 73/23/EEC, EN 55014, EN 60745,
EN 61000
LpA (sound pressure) 97.3 dB(A),
LWA (acoustic power) 108.3 dB(A),
hand/arm weighted vibration 10.7 m/s2
KpA (sound pressure uncertainty) 3 dB(A),
KWA (acoustic power uncertainty) 3 dB(A)
Kevin Hewitt
Director of Consumer Engineering
Spennymoor, County Durham DL16 6JG,
United Kingdom
1-9-2005
Guarantee
Black & Decker is confident of the quality of its products and
offers an outstanding guarantee. This guarantee statement is
in addition to and in no way prejudices your statutory rights.
The guarantee is valid within the territories of the Member
States of the European Union and the European Free Trade
Area.
If a Black & Decker product becomes defective due to faulty
materials, workmanship or lack of conformity, within 24 months
from the date of purchase, Black & Decker guarantees to replace
defective parts, repair products subjected to fair wear and tear
or replace such products to ensure minimum inconvenience to
the customer unless:
◆ The product has been used for trade, professional or hire
purposes;
◆ The product has been subjected to misuse or neglect;
◆ The product has sustained damage through foreign
objects, substances or accidents;
◆ Repairs have been attempted by persons other than
authorised repair agents or Black & Decker service staff.
To claim on the guarantee, you will need to submit proof of
purchase to the seller or an authorised repair agent. You can
check the location of your nearest authorised repair agent by
contacting your local Black & Decker office at the address
indicated in this manual. Alternatively, a list of authorised
Black & Decker repair agents and full details of our after-sales
service and contacts are available on the Internet at:
www.2helpU.com.
Please register at our website www.blackanddecker.com
to be kept up to date on new products and special offers.
Further information on the Black & Decker brand and our range
of products is available at www.blackanddecker.com.
6
TYP
1
KR60 - KR60L - KR60QC
25
24
15
20
23
1
17
16
7
KR60
KR60QC
2
9
10
42
6
40
KR60L
35
2
8
22
13
32
14
31
29
19
26
26
30
11
21
33
18
KR60QC
4
22
37
5
12
KR60L
11
KR60 - KR60L
KR60 - KR60QC
21
KR60 - KR60L
34
28
43
41
1
800
E13603
WWW.2helpU.com
17 - 04 - 03
7
TYP
1
KR70 - KR70L - KR70QC
25
24
15
1
20
23
17
16
22
KR70
KR70QC
7
9
10
42
2
6
21
40
KR70 - KR70L
KR70L
35
2
8
22
13
31
29
19
26
30
32
14
21
33
18
26
KR70QC
4
37
5
12
KR70L
KR70 - KR70QC
34
11
28
43
41
27
KR70QC
1
11
800
27
KR70 - KR70L
E13604
615560-00
8
WWW.2helpU.com
17 - 04 - 03
09/05
9
10
11
Australia
Black & Decker (Australia) Pty. Ltd. Tel. 03-8720 5100
20 Fletcher Road, Mooroolbark,
Fax 03-9727 5940
Victoria, 3138
New Zealand
Black & Decker
81 Hugo Johnston Drive
Penrose, Auckland, New Zealand
United Kingdom
Black & Decker
210 Bath Road
Slough, Berkshire SL1 3YD
615560-00
12
Tel. 09 579 7600
Fax 09 579 8200
Tel. 01753 511234
Fax 01753 551155
Helpline 01753 574277
09/05
Download PDF