KW712 | Black&Decker KW712 PLANER instruction manual

www.blackanddecker.com
4
5
3
1
2
UK
Ireland
Australia
New Zealand
1
7
6
4
5
8
A
B
9 10
3
11
D
C
13
12
15
14
16
17
17
16
15
14
E
2
18 19
3
22
24
23
F
G
21
20
3
Intended use
Your Black & Decker planer has been designed for planing
wood, wood products and plastics. The tool is intended for
hand-held use. This tool is intended for consumer use only.
Safety instructions
◆
◆
◆
◆
Warning! When using mains-powered tools, basic safety
precautions, including the following, should always be
followed to reduce the risk of fire, electric shock,
personal injury and material damage.
Read all of this manual carefully before operating the tool.
Retain this manual for future reference.
Remove the plug from the socket before carrying out any
adjustment, servicing or maintenance.
Keep work area clean
Cluttered areas and benches can cause accidents.
Consider work area environment
Do not expose the tool to rain. Do not use the tool in damp or
wet conditions. Keep the work area well lit. Do not use the
tool where there is a risk of causing fire or explosion, e.g. in
the presence of flammable liquids and gases.
Keep children away
Do not allow children, visitors or animals to come near the
work area or to touch the tool or mains cable.
Dress properly
Do not wear loose clothing or jewellery, as these can be
caught in moving parts. Preferably wear rubber gloves and
non-slip footwear when working outdoors. Wear protective
hair covering to keep long hair out of the way.
Personal protection
Always use safety glasses. Use a face or dust mask whenever
the operations may produce dust or flying particles.
Hearing protection should be worn.
Guard against electric shock
Prevent body contact with earthed or grounded surfaces
(e.g. pipes, radiators, cookers and refrigerators). Electric safety
can be further improved by using a high-sensitivity
(30 mA / 30 mS) residual current device (RCD).
Do not overreach
Keep proper footing and balance at all times.
Stay alert
Watch what you are doing. Use common sense.
Do not operate the tool when you are tired.
Secure workpiece
Use clamps or a vice to hold the workpiece. It is safer and it
frees both hands to operate the tool.
Connect dust extraction equipment
If devices are provided for the connection of dust extraction
and collection facilities, ensure that these are connected and
properly used.
4
Remove adjusting keys and wrenches
Always check that adjusting keys and wrenches are removed
from the tool before operating the tool.
Extension cables
Before use, inspect the extension cable and replace if damaged.
When using the tool outdoors, only use extension cables
intended for outdoor use. Up to 30 m of Black & Decker
extension cable can be used without loss of power.
Use appropriate tool
The intended use is described in this instruction manual.
Do not force small tools or attachments to do the job of a
heavy-duty tool. The tool will do the job better and safer at the
rate for which it was intended. Do not force the tool.
Do not use the tool for purposes not intended, for example,
do not use a circular saw to cut tree limbs or logs.
Warning! The use of any accessory or attachment or
performance of any operation with this tool other than those
recommended in this instruction manual may present a risk of
personal injury.
Check for damaged parts
Before use, carefully check the tool and mains cable for
damage. Check for misalignment and seizure of moving parts,
breakage of parts, damage to guards and switches and any
other conditions that may affect its operation. Ensure that the
tool will operate properly and perform its intended function.
Do not use the tool if any part is damaged or defective. Do not
use the tool if the switch does not turn it on and off. Have any
damaged or defective parts repaired or replaced by an
authorised repair agent. Never attempt any repairs yourself.
Unplug the tool
Unplug the tool when it is not in use, before changing any
parts of the tool, accessories or attachments and before
servicing.
Avoid unintentional starting
Do not carry the tool with a finger on the on/off switch.
Be sure that the tool is switched off when plugging in.
Do not abuse cord
Never carry the tool by its cord or pull it to disconnect from the
socket. Keep the cord away from heat, oil and sharp edges.
Store idle tools
When not in use, tools should be stored in a dry, locked up or
high place, out of reach of children.
Maintain tools with care
Keep cutting tools sharp and clean for better and safer
performance. Follow the instructions for maintenance and
changing accessories. Keep handles and switches dry,
clean and free from oil and grease.
Repairs
This tool complies with relevant safety requirements.
Repairs should only be carried out by qualified persons using
original spare parts; otherwise this may result in considerable
danger to the user.
Electrical safety
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
Additional safety instructions for Australia and
New Zealand
◆ This appliance is not intended for use by young or infirm
persons without supervision. Children must be supervised
to ensure they do not play with the appliance.
◆ If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Additional safety instructions for planers
◆ Remove all nails and metal objects from the workpiece
before planing.
◆ Always hold the tool with both hands and by the handles
provided.
◆ Use sharp cutting blades only.
◆ Never put the tool down until the cutting blades have
come to a complete standstill.
◆ Immediately disconnect the cable from the mains if it is
damaged or cut.
Features
This tool includes some or all of the following features.
1. On/off switch
2. Lock-off button
3. Shavings discharge outlet
4. Planing depth adjustment knob
5. Planing depth graduation
Assembly
Warning! Make sure that the tool is switched off and
unplugged.
Replacing the cutting blades (fig. A)
The cutting blades provided with this tool are reversible.
Replacement cutting blades can be obtained from your local
retailer.
◆
◆
Adjusting the depth of cut (fig. B)
The depth of cut is indicated by the marking (8). The setting
range can be read from the graduation (5).
◆ Turn the planing depth adjustment knob (4) to the required
depth of cut.
◆ Turn the knob to the ‘P’ postion whenever the tool is not
in use.
Fitting and removing the parallel fence (fig. C)
The parallel fence is used to for optimum control on narrow
workpieces.
◆ Loosen the locking knob (9).
◆ Insert the parallel fence (11) through the opening (10).
◆ Slide the parallel fence into the desired position.
◆ Tighten the locking knob.
◆ To remove the parallel fence proceed in reverse order.
Connecting a vacuum cleaner to the tool (fig. D)
An adaptor is required to connect a vacuum cleaner or dust
extractor to the tool. The adaptor can be purchased from your
local Black & Decker retailer.
◆ Slide the adaptor (12) over the shavings discharge outlet (3).
◆ Connect the vacuum cleaner hose (13) to the adaptor.
Assembling and fitting the shavings collection bag (fig. E)
The shavings collection bag is particularly useful when
working in confined spaces.
Before first use, you will have to assemble the shavings
collection bag.
◆ Fit the wire frames (14) to the connecting plate (15) using
the screws (16) and washers (17).
◆ Pull the cloth bag (18) over the frame structure as shown.
Take care that the elasticated mouth (19) is well fitted
around the edge of the connecting plate (15).
◆ Slide the connecting plate over the shavings discharge
outlet (3).
Use
◆
Removing
◆ Loosen the bolts (6) using the spanner supplied.
◆ Slide the blade (7) out of the holder.
◆ Reverse the blade so that the unused side comes in
position. If both sides are worn, the blade must be
replaced.
Fitting
◆ Slide the blade into the holder until it is against the end
stop.
Tighten the bolts using the spanner supplied.
Always replace both cutters.
◆
◆
Adjust the depth of cut.
If necessary, fit and adjust the parallel fence.
Use sharp cutters only.
Switching on and off
Switching on
◆ Keep the lock-off button (2) depressed and press the on/
off switch (1).
◆ Release the lock-off button.
5
Switching off
◆ Release the on/off switch.
Planing
◆ Hold the tool with the nose piece of the shoe resting on
top of the workpiece surface.
◆ Switch the tool on.
◆ Move the tool steadily forward to perform the cutting stroke.
◆ Switch the tool off after the stroke has been completed.
Rebating (fig. F)
◆ Fit and adjust the parallel fence.
◆ Proceed as for planing.
Chamfering edges
The V-groove in the nose piece of the shoe enables you to
chamfer edges at 45° angles.
◆ Hold the tool at an angle with the groove around the edge
of the workpiece and perform the cutting stroke.
Maintenance
Your tool has been designed to operate over a long period of
time with a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular cleaning.
◆ Regularly clean the ventilation slots in your tool using a
soft brush or dry cloth.
◆ Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
Never let any liquid get inside the tool and never immerse
any part of the tool into liquid.
Replacing the drive belt (fig. G)
◆ Loosen the screws (20) and remove the cover (21).
◆ Remove the old drive belt.
◆ Place the new belt (22) over the pulleys. Place the belt
over the large pulley (23) first, then over the small pulley
(24), whilst manually rotating the belt steadily.
◆ Put the cover back in place and tighten the screws.
Protecting the environment
Emptying the shavings collection bag
The shavings collection bag should be emptied regularly while
using it.
◆ Unzip the bag and empty it before continuing.
Hints for optimum use
◆
◆
◆
Move the tool along the grain of the wood.
If the grain is cross or curly, or if the workpiece material is
a hard type of wood, adjust the depth of cut to take only a
very thin shaving at each pass and take several passes to
achieve the desired result.
To keep the tool in a straight line, press down the front of
the tool at the start, and press down the back of the tool
at the end of the cutting stroke.
Accessories
The performance of your tool depends on the accessory used.
Black & Decker and Piranha accessories are engineered to
high quality standards and designed to enhance the performance
of your tool. By using these accessories you will get the very
best from your tool.
The following types of cutting blades can be obtained from
your local retailer:
- Tungsten carbide tipped reversible cutting blades
(part no. X35007, supplied per pair)
- High-speed steel reversible cutting blades
(part no. X24192-XJ11, supplied per pair)
6
Black & Decker provides a facility for recycling
Black & Decker products once they have reached the
end of their working life. This service is provided
free of charge. To take advantage of this service
please return your product to any authorised repair
agent who will collect them on our behalf.
You can check the location of your nearest authorised repair
agent by contacting your local Black & Decker office at the
address indicated in this manual. Alternatively, a list of
authorised Black & Decker repair agents and full details of our
after-sales service and contacts are available on the Internet
at: www.2helpU.com.
Technical data
Voltage
Power input
No-load speed
Planing width
Planing depth (max.)
Rebating depth (max.)
Weight
VAC
W
min-1
mm
mm
mm
kg
KW712
230
650
17,000
82
2
8
3
EC declaration of conformity
Black & Decker declares that these products conform to:
98/37/EC, 89/336/EEC, 73/23/EEC, EN 50144, EN 55014-1,
EN 55014-2
LpA (sound pressure): 89.1 dB(A), LWA (acoustic power)
102.1 dB(A), hand/arm weighted vibration < 2.5 m/s2
Kevin Hewitt
Director of Consumer Engineering
Spennymoor, County Durham DL16 6JG,
United Kingdom
Guarantee
Black & Decker is confident of the quality of its products and
offers an outstanding guarantee. This guarantee statement is
in addition to and in no way prejudices your statutory rights.
The guarantee is valid within the territories of the Member
States of the European Union and the European Free Trade
Area.
If a Black & Decker product becomes defective due to faulty
materials, workmanship or lack of conformity, within 24 months
from the date of purchase, Black & Decker guarantees to
replace defective parts, repair products subjected to fair wear
and tear or replace such products to ensure minimum
inconvenience to the customer unless:
◆ The product has been used for trade, professional or hire
purposes;
◆ The product has been subjected to misuse or neglect;
◆ The product has sustained damage through foreign
objects, substances or accidents;
◆ Repairs have been attempted by persons other than
authorised repair agents or Black & Decker service staff.
To claim on the guarantee, you will need to submit proof of
purchase to the seller or an authorised repair agent. You can
check the location of your nearest authorised repair agent by
contacting your local Black & Decker office at the address
indicated in this manual. Alternatively, a list of authorised
Black & Decker repair agents and full details of our after-sales
service and contacts are available on the Internet at:
www.2helpU.com.
Please register at our website www.blackanddecker.com
to be kept up to date on new products and special offers.
Further information on the Black & Decker brand and our range
of products is available at www.blackanddecker.com.
Australia
Black & Decker (Australia) Pty. Ltd. Tel. 03-8720 5100
20 Fletcher Road, Mooroolbark,
Fax 03-9727 5940
Victoria, 3138
New Zealand
Black & Decker
Tel. 09 579 7600
81 Hugo Johnston Drive
Fax 09 579 8200
Penrose, Auckland, New Zealand
United Kingdom
Black & Decker
210 Bath Road
Slough, Berkshire SL1 3YD
Tel. 01753 511234
Fax 01753 551155
Helpline 01753 574277
7
12
11
13
1
18
2
19
3
4
5
7
6
15
14
8 22
16
17
21
20
23
9
10
37
39
24
25
28
29
26
30
27
32
38
33 34
35
36
48
49
50
51
53
46
42
31
52
47
41
43
40
45
44
54
60
56
55
57
63
59
64
65
61
58
585076-00
8
62
04/03
Download PDF