HP9019K | Black&Decker HP9019K CORDLESS SCREWDRIVER instruction manual

HP9012
HP9019
UK
Ireland
Australia
New Zealand
1
4
6
7
3
2
1
5
8
A
7
8
9
3
C
4
B
2
D
6
2
5
E
8
F
3
Intended use
Your Black & Decker drill/screwdriver has been designed for
screwdriving applications and for drilling in wood, metal and
plastics. This tool is intended for consumer use only.
Your Black & Decker charger has been designed for charging
the battery in the tool with which it was supplied.
Safety instructions
Warning! When using battery-powered tools, basic
safety precautions, including the following, should always
be followed to reduce the risk of fire, leaking batteries,
personal injury and material damage.
◆ Read all of this manual carefully before operating the tool.
◆ Retain this manual for future reference.
Keep work area clean
Cluttered areas and benches can cause accidents.
Consider work area environment
Do not expose the tool to rain. Do not use the tool in damp or
wet conditions. Keep the work area well lit. Do not use the
tool where there is a risk of causing fire or explosion, e.g. in
the presence of flammable liquids and gases.
Keep children away
Do not allow children, visitors or animals to come near the
work area or to touch the tool.
Dress properly
Do not wear loose clothing or jewellery, as these can be
caught in moving parts. Preferably wear rubber gloves and
non-slip footwear when working outdoors. Wear protective
hair covering to keep long hair out of the way.
Personal protection
Always use safety glasses. Use a face or dust mask whenever
the operations may produce dust or flying particles.
Hearing protection should be worn.
Do not overreach
Keep proper footing and balance at all times.
Stay alert
Watch what you are doing. Use common sense.
Do not operate the tool when you are tired.
Secure workpiece
Use clamps or a vice to hold the workpiece. It is safer and it
frees both hands to operate the tool.
Connect dust extraction equipment
If devices are provided for the connection of dust extraction
and collection facilities, ensure that these are connected and
properly used.
Remove adjusting keys and wrenches
Always check that adjusting keys and wrenches are removed
from the tool before operating the tool.
Use appropriate tool
The intended use is described in this instruction manual.
Do not force small tools or attachments to do the job of a
heavy-duty tool.
◆
4
The tool will do the job better and safer at the rate for which it
was intended. Do not force the tool.
Warning! The use of any accessory or attachment or performance
of any operation with this tool other than those recommended
in this instruction manual may present a risk of personal injury.
Check for damaged parts
Before use, carefully check the tool for damage. Check for
misalignment and seizure of moving parts, breakage of parts,
damage to guards and switches and any other conditions that
may affect its operation. Ensure that the tool will operate
properly and perform its intended function. Do not use the tool
if any part is damaged or defective. Do not use the tool if the
switch does not turn it on and off. Have any damaged or
defective parts repaired or replaced by an authorised repair
agent. Never attempt any repairs yourself.
Remove the battery
Where the design permits, remove the battery when the tool
is not in use, before changing any parts of the tool,
accessories or attachments and before servicing.
Avoid unintentional starting
Do not carry the tool with a finger on the on/off switch.
Be sure that the tool is switched off when inserting the
battery into the tool.
Do not abuse cord
Never carry the charger by its cord or pull it to disconnect from
the socket. Keep the cord away from heat, oil and sharp edges.
Store idle tools
When not in use, tools, batteries and chargers should be stored
in a dry, locked up or high place, out of reach of children.
Maintain tools with care
Keep cutting tools sharp and clean for better and safer
performance. Follow the instructions for maintenance and
changing accessories. Keep handles and switches dry,
clean and free from oil and grease.
Repairs
This tool complies with relevant safety requirements.
Repairs should only be carried out by qualified persons using
original spare parts; otherwise this may result in considerable
danger to the user.
Additional safety instructions for batteries and chargers
Batteries
◆ Never attempt to open for any reason.
◆ Do not expose the battery to water.
◆ Do not store in locations where the temperature may
exceed 40 °C.
◆ Charge only at ambient temperatures between 4 °C and
40 °C.
◆ Charge only using the charger provided with the tool.
◆ When disposing of batteries, follow the instructions given
in the section “Protecting the environment”.
◆
Under extreme conditions, battery leakage may occur.
When you notice liquid on the battery, proceed as follows:
- Carefully wipe the liquid off using a cloth. Avoid skin
contact.
- In case of skin or eye contact, follow the instructions
below.
Warning! The battery fluid, a 25-30% solution of potassium
hydroxide, can be harmful. In case of skin contact, immediately
rinse with water. Neutralise with a mild acid such as lemon
juice or vinegar. In case of eye contact, rinse abundantly with
clean water for at least 10 minutes. Consult a physician.
◆ Do not incinerate the battery.
◆ Do not attempt to charge damaged batteries.
Fitting and removing a drill bit or screwdriver bit
(fig. C & F)
This tool uses screwdriver bits and drill bits with a 1/4"
(6.35) mm hexagonal shank.
◆ Lock the tool by setting the forward/reverse slider (2) to
the centre position (fig. F).
◆ Pull back the bit holder sleeve (3) (fig. C).
◆ Insert the bit shaft (7) into the bit holder.
◆ Release the bit holder sleeve.
Use
Warning! Before drilling into walls, floors or ceilings,
check for the location of wiring and pipes.
Chargers
◆ Use your Black & Decker charger only to charge the battery
in the tool with which it was supplied. Other batteries
could burst, causing personal injury and damage.
◆ Never attempt to charge non-rechargeable batteries.
◆ Have defective cords replaced immediately.
◆ Do not expose the charger to water.
◆ Do not open the charger.
◆ Do not probe the charger.
Charging the battery (fig. E)
The battery needs to be charged before first use and whenever
it fails to produce sufficient power on jobs that were easily
done before.
When charging the battery for the first time, or after
prolonged storage, it will only accept an 80% charge.
After several charge and discharge cycles, the battery will
attain full capacity. The battery may become warm while
charging; this is normal and does not indicate a problem.
The charger is intended for indoor use only.
Warning! Do not charge the battery at ambient temperatures
below 4 °C or above 40 °C. Recommended charging
temperature: approx. 24 °C.
Electrical safety
Your charger is double insulated; therefore no earth
wire is required. Always check that the mains
voltage corresponds to the voltage on the rating
plate. Never attempt to replace the charger unit with
a regular mains plug.
Overview (fig. A)
1.
2.
3.
4.
5.
6.
7.
8.
Variable speed switch
Forward/reverse slider
Bit holder sleeve
Head adjustment button
Charger
Charger plug
Screwdriver bit
Battery
Assembly
Fitting and removing the battery (fig. B)
◆ To fit the battery (8), line it up with the receptacle on the
tool. Slide the battery into the receptacle and push until
the battery snaps into place.
◆ To remove the battery, push the release button (9) while
at the same time pulling the battery out of the receptacle.
To charge the battery (8), remove it from the tool.
Slide the charger receptacle (5) onto the battery as
shown.
◆ Plug in the charger (6).
The battery will become warm while charging. After approx. 3
hours of charging, the battery will be fully charged.
◆ Remove the charger receptacle from the battery.
◆
◆
Adjusting the head (fig. D)
For optimum versatility, the head can be set to different positions.
◆ Press the head adjustment button (4) down.
◆ Swivel the head into the desired position.
◆ Release the button.
Selecting the direction of rotation (fig. F)
For drilling and for tightening screws, use forward (clockwise)
rotation. For loosening screws or removing a jammed drill bit,
use reverse (counterclockwise) rotation.
◆ To select forward rotation, push the forward/reverse
slider (2) to the left.
◆ To select reverse rotation, push the forward/reverse slider
to the right.
5
◆
To lock the tool, set the forward/reverse slider into the
centre position.
Drilling/screwdriving (fig. A)
◆ Select forward or reverse rotation using the forward/
reverse slider (2).
◆ To switch the tool on, press the switch (1). The tool speed
depends on how far you press the switch.
◆ To switch the tool off, release the switch.
Setting the torque
This tool is fitted with a collar to set the torque for tightening
screws. Large screws and hard workpiece materials require a
higher torque setting than small screws and soft workpiece
materials. The collar has a wide range of settings to suit your
application.
◆ Turn the collar to the desired setting. If you do not yet
know the appropriate setting, proceed as follows:
- Set the collar to the lowest torque setting.
- Tighten the first screw.
- If the clutch ratchets before the desired result is achieved,
increase the collar setting and continue tightening the
screw. Repeat until you reach the correct setting. Use this
setting for the remaining screws.
Hints for optimum use
Drilling
◆ Always apply a light pressure in a straight line with the
drill bit.
◆ Just before the drill tip breaks through the other side of
the workpiece, decrease pressure on the tool.
◆ Use a block of wood to back up workpieces that may splinter.
◆ Use HSS drill bits when drilling in metal.
◆ Use a lubricant when drilling metals other than cast iron
and brass.
◆ Make an indentation using a centre punch at the centre of
the hole to be drilled in order to improve accuracy.
Screwdriving
◆ Always use the correct type and size of screwdriver bit.
◆ If screws are difficult to tighten, try applying a small
amount of washing liquid or soap as a lubricant.
◆ Always hold the tool and screwdriver bit in a straight line
with the screw.
◆ When screwing in wood, it is recommended to drill a pilot
hole with a depth equal to the length of the screw.
◆ A pilot hole guides the screw and prevents splintering or
distortion of the wood. For the optimum size of the pilot
hole, refer to the table below.
6
◆
When screwing in hardwood, also drill a clearance hole
with a depth equal to half the length of the screw. For the
optimum size of the clearance hole, refer to the table below.
Screw size
No. 6 (3.5 mm)
No. 8 (4 mm)
No. 10 (5 mm)
Pilot hole ø (softwood)
2 mm
3.2 mm
3.5 mm
Screw size
No. 6 (3.5 mm)
No. 8 (4 mm)
No. 10 (5 mm)
Pilot hole ø (hardwood)
2.5 mm
3.5 mm
4.0 mm
Screw size
No. 6 (3.5 mm)
No. 8 (4 mm)
No. 10 (5 mm)
Clearance hole
4 mm
5.0 mm
5.7 mm
Accessories
The performance of your tool depends on the accessory used.
Black & Decker and Piranha accessories are engineered to high
quality standards and designed to enhance the performance of
your tool. By using these accessories you will get the very best
from your tool. This tool uses screwdriver bits and drill bits
with a 1/4" (6.35 mm) hexagonal shank. Piranha Super-lok
accessories are designed for use with this tool.
Maintenance
Your Black & Decker tool has been designed to operate over a
long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Warning! Before performing any maintenance on the tool,
set the forward/reverse slider to the centre position.
Unplug the charger before cleaning it.
◆
◆
Regularly clean the ventilation slots in your tool using a
soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
Protecting the environment
Guarantee
Tools
Black & Decker provides a facility for recycling
Black & Decker products and rechargeable batteries
once they have reached the end of their working life.
This service is provided free of charge. To take
advantage of this service please return your product
to any authorised repair agent who will collect them
on our behalf.
Batteries
Black & Decker batteries can be recharged many
times. At the end of their useful life, discard
Cd
batteries with due care for our environment:
◆ Run the battery down completely, then remove it from the
tool.
◆ NiCd and NiMH batteries are recyclable. Take them to
your service agent or a local recycling station.
Collected batteries will be recycled or disposed of
properly.
Technical data
Voltage
VDC
No-load speed
min-1
Max. torque
Nm
Bit holder
Max. drilling capacity in steel/wood mm
Weight
kg
Charger
Input voltage
Approx. charging time
HP9012/HP9019
12
0 - 700
8.3
1/4" (6.35 mm hex)
9.5 / 12.7
1.5
Black & Decker is confident of the quality of its products and
offers an outstanding guarantee. This guarantee statement is
in addition to and in no way prejudices your statutory rights.
The guarantee is valid within the territories of the Member
States of the European Union and the European Free Trade
Area.
If a Black & Decker product becomes defective due to faulty
materials, workmanship or lack of conformity, within 24 months
from the date of purchase, Black & Decker guarantees to
replace defective parts, repair products subjected to fair wear
and tear or replace such products to ensure minimum
inconvenience to the customer unless:
◆ The product has been used for trade, professional or hire
purposes;
◆ The product has been subjected to misuse or neglect;
◆ The product has sustained damage through foreign
objects, substances or accidents;
◆ Repairs have been attempted by persons other than
authorised repair agents or Black & Decker service staff.
To claim on the guarantee, you will need to submit proof of
purchase to the seller or an authorised repair agent. You can
check the location of your nearest authorised repair agent by
contacting your local Black & Decker office at the address
indicated in this manual. Alternatively, a list of authorised
Black & Decker repair agents and full details of our after-sales
service and contacts are available on the Internet at:
www.2helpU.com.
VAC 230
h 3
EC declaration of conformity
Black & Decker declares that these products conform to:
98/37/EC, 89/336/EEC, 73/23/EEC, EN 50260, EN 55014,
EN 60335, EN 61000
LpA (sound pressure): $ dB(A), LWA (acoustic power) $ dB(A),
hand/arm weighted vibration < 2.5 m/s2
Colin Wills, Director of Engineering
BDCI, 4/F, 2 Dai Wang Street
Tai Po Industrial Estate
Tai Po NT, Hong Kong
Australia
DEWALT Industrial Power Tool Company
7 Clarice Road
Tel. 03 9895 9200
Box Hill, Victoria 3128
Fax 03 9899 7465
New Zealand
Black & Decker
Tel. 09 579 7600
81 Hugo Johnson Drive
Fax 09 579 8200
Penrose, Auckland, New Zealand
United Kingdom
Black & Decker
210 Bath Road
Slough, Berkshire SL1 3YD
Tel. 01753 511234
Fax 01753 551155
Helpline 01753 574277
7
5101888-04
8
06/03
Download PDF