MT3000K | Black&Decker MT3000K WALLPAPER STRIPPER instruction manual

www.blackanddecker.co.uk
9
8
2
1
4
7
6
UK
5
Ireland
3
12
11
10
Australia
New Zealand
1
15
16
21
14 13
A
20
17
18
19
3
B
23
19
6
C
2
22
D
24
11
10
180 o
8
13
F
E
27
14
26
25
11
10
G
H
30
28
29
26
I
5
J
3
Intended use
Your Black & Decker multi-purpose tool has been designed for
a wide range of DIY applications.
Using the screwdriver head, this tool is intended for
screwdriving applications.
Using the sander head, this tool is intended for sanding wood,
metal, plastics and painted surfaces.
Using the preparation head, this tool is intended for scraping
decorating materials, such as paint layers and adhesives,
from wood, metal and plastics.
This tool is intended for consumer use only.
General safety rules
Warning! Read all instructions. Failure to follow all
instructions listed below may result in electric shock, fire and/
or serious injury. The term “power tool” in all of the warnings
listed below refers to your mains operated (corded) power tool
or battery operated (cordless) power tool.
SAVE THESE INSTRUCTIONS.
1. Work area
a. Keep work area clean and well lit. Cluttered and dark
areas invite accidents.
b. Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases
or dust. Power tools create sparks which may ignite the
dust or fumes.
c. Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs
with earthed (grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock
if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase the
risk of electric shock.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of electric
shock.
4
3. Personal safety
a. Stay alert, watch what you are doing and use
common sense when operating a power tool. Do not
use a power tool while you are tired or under the
influence of drugs, alcohol or medication. A moment
of inattention while operating power tools may result in
serious personal injury.
b. Use safety equipment. Always wear eye protection.
Safety equipment such as dust mask, non-skid safety
shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
c. Avoid accidental starting. Ensure the switch is in
the off position before plugging in. Carrying power
tools with your finger on the switch or plugging in power
tools that have the switch on invites accidents.
d. Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power tool
in unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these
are connected and properly used. Use of these
devices can reduce dust related hazards.
4. Power tool use and care
a. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will do
the job better and safer at the rate for which it was designed.
b. Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
c. Disconnect the plug from the power source before
making any adjustments, changing accessories, or
storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users.
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f.
Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc.,
in accordance with these instructions and in the
manner intended for the particular type of power
tool, taking into account the working conditions
and the work to be performed. Use of the power tool
for operations different from those intended could result
in a hazardous situation.
5. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Electrical safety
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
Additional safety instructions for drill/screwdrivers
◆ Before drilling into walls, floors or ceilings, check for the
location of wiring and pipes.
◆ Avoid touching the tip of a drill bit just after drilling,
as it may be hot.
Additional safety instructions for sanders
◆ Always wear a dust mask whenever sanding.
◆ Thoroughly remove all dust after sanding.
◆ Take special care when sanding paint which is possibly
lead based or when sanding some woods and metal
which may produce toxic dust:
- Wear a dust mask specifically designed for protection
against lead paint dust and fumes and ensure that persons
within or entering the work area are also protected.
- Do not let children or pregnant women enter the work
area.
- Do not eat, drink or smoke in the work area.
- Dispose of dust particles and any other debris safely.
Additional safety instructions for Australia and
New Zealand
◆ This appliance is not intended for use by young or infirm
persons without supervision. Children must be supervised
to ensure they do not play with the appliance.
◆ If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Overview (fig. A)
Motor unit
1. On/off switch
2. Lock-on button
3. Head release button
4. Bit storage
Screwdriver head
5. Forward/reverse switch
6. Bit holder
Sander head
7. Sanding base
8. Sanding base tip
9. Dust extraction outlet
Preparation head
10. Mounting shaft
11. Clamp plate
12. Allen key storage
Fig. A
In addition, this tool is supplied with some or all of the
following accessories.
13. Scraper head
14. Blade cover
15. Rigid parallel blade
16. Flexible parallel blade
17. Screw driver bit
18. Drill bits
19. Sanding sheet
20. Abrasive pad
21. Dust extraction adaptor
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting and removing tool heads (fig. B)
The different tool heads can be easily exchanged.
◆ To remove a tool head, depress the head release button
(3) and take the head off the tool.
◆ To fit a tool head, line it up with the tool as shown and
push it onto the tool until it snaps into place.
Fitting and removing a screwdriver bit (fig. C)
◆ Pull the sleeve (22) backward.
◆ Insert the bit shaft into the bit holder (6) as far as it will go.
◆ Release the sleeve to secure the bit.
◆ To remove the bit, pull sleeve backward and pull the bit
out firmly.
This tool is supplied with a screwdriver bit in the bit storage (4).
This tool includes some or all of the following features.
5
◆
◆
To remove the screwdriver bit from the bit storage press
the bit down into the bit holder recess (4), then lift the bit
out.
To store the screwdriver bit, firmly push it into the storage.
Fitting sanding sheets (fig. D)
◆ Detach the two diamond-shaped tips (23) from the
sanding sheet (19).
◆ Hold the tool with the sanding base facing upwards.
◆ Place the sanding sheet (19) onto the sanding base,
making sure that the holes in the sheet line up with the
holes in the base.
The diamond-shaped tip (23) can be reversed and replaced
when worn.
◆ When the front part of the tip is worn, detach it from the
sheet, reverse it and press it onto the sanding base again.
◆ When the whole tip is worn, remove it from the sanding
base and fit a new tip.
◆
◆
◆
Align the tab on the clamp plate (11) with the slot in the
shaft (10) and the blade.
Fit the clamp plate to the shaft by tightening the screw (27).
To remove the blade, remove the screw (19) and the
clamp plate, and take the blade from the shaft.
Replacing the cutting blade (fig. I)
The cutting blade provided with this tool is reversible.
Replacement cutting blades can be obtained from your local
retailer.
◆ Loosen the screw (28) and remove it.
◆ Remove the cutter clamp plate (29).
◆ Reverse the blade (26) so that the unused side comes in
position. If both sides are worn, the blade must be replaced.
◆ Re-install the cutter clamp plate.
◆ Re-fit the screw and tighten it.
Use
Warning! Let the tool work at its own pace. Do not overload.
Warning! Never use the sanding head without a sanding
sheet or accessory in place.
Tip of the sanding base (fig. E)
When the sanding base tip (8) is worn, it can be reversed or
replaced. Spare parts are available from your Black & Decker
dealer.
◆ Reverse or replace the worn part.
Fitting and removing the scraper head (fig. F)
◆ Slide the scraper head (13) onto the shaft (10).
◆ Align the tab on the clamp plate (11) with the slot in the
shaft.
◆ Fit the clamp plate to the shaft by tightening the screw (24).
◆ To remove the head, remove the screw (19) and the clamp
plate, and pull the head from the shaft.
Removing and fitting the blade cover (fig. G)
◆ Hold the blade cover (14) at the ends.
◆ Lift the blade cover slightly to release it from the screw
(25) and pull the cover off. Take care not to contact the
edges of the blade (26).
◆ To fit the blade cover, hold the cover at the ends and
place it over the claw blade. Push the cover until it snaps
into place.
Warning! Always keep the blade cover in place when the
scraper head is not being used.
Fitting and removing a parallel blade (fig. H)
◆ Select the required parallel blade.
◆ Align the slot on the mounting end of the blade with the
slot in the shaft (10).
6
Warning! Do not cover the ventilation slots when using the
tool to avoid overheating.
Selecting the direction of rotation (fig. J)
For tightening screws, use forward (clockwise) rotation.
For loosening screws, use reverse (counterclockwise) rotation.
◆ To select forward rotation, press the lock-off button (30)
and push the forward/reverse switch (5) to the left.
◆ To select reverse rotation, press the lock-off button and
push the forward/reverse switch to the right.
Warning! Never change the direction of rotation while the
motor is running.
Switching on and off
◆ To switch the tool on, press the on/off switch (1).
◆ For continuous operation, press the lock-on button (2) and
release the on/off switch.
◆ To switch the tool off, release the on/off switch.
◆ To switch the tool off when in continuous operation,
press the on/off switch once more and release it.
Hints for optimum use
Screwdriving
◆ Always use the correct type and size of screwdriver bit.
◆ If screws are difficult to tighten, try applying a small
amount of washing liquid or soap as a lubricant.
◆ Always hold the tool and screwdriver bit in a straight line
with the screw.
Sanding
◆ Do not exert too much pressure on the tool.
◆ Regularly check the condition of the sanding sheet.
Replace when necessary.
◆ When sanding new layers of paint before applying
another layer, use extra fine grit.
◆ On very uneven surfaces, or when removing layers of
paint, start with a coarse grit. On other surfaces,
start with a medium grit. In both cases, gradually change
to a fine grit for a smooth finish.
◆ Use the abrasive pad for removing rust.
◆ Consult your retailer for more information on available
accessories for sanding, polishing, stripping and scrubbing.
Preparation
◆ Choose the correct type of blade for the application. Use
the claw blade for loose or flaking paint. Use the flexible
blade for soft materials. Use the rigid blade for hard materials.
◆ Push or pull the blade steadily over the surface material.
Note that the blade will not move until it is pressed
against the material.
◆ Do not exert too much pressure on the tool.
Maintenance
Your tool has been designed to operate over a long period of
time with a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular cleaning.
◆ Regularly clean the ventilation slots in your tool using
a soft brush or dry cloth.
◆ Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
◆ Safely dispose of the old plug.
◆ Connect the brown lead to the live terminal in the new plug.
◆ Connect the blue lead to the neutral terminal.
Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality
plugs. Recommended fuse: 5 A.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand for
raw materials.
Local regulations may provide for separate collection of
electrical products from the household, at municipal waste
sites or by the retailer when you purchase a new product.
Black & Decker provides a facility for the collection and
recycling of Black & Decker products once they have reached
the end of their working life. To take advantage of this service
please return your product to any authorised repair agent who
will collect them on our behalf.
You can check the location of your nearest authorised repair
agent by contacting your local Black & Decker office at the
address indicated in this manual. Alternatively, a list of
authorised Black & Decker repair agents and full details of our
after-sales service and contacts are available on the Internet
at: www.2helpU.com
Technical data
Voltage
Power input
Screwdriver:
No-load speed
Bit holder
Max. drilling capacity in steel/wood
Sander:
Oscillations (no load)
Preparation:
Strokes (no load)
Weight
with screwdriver head
with sander head
with preparation head
VAC
W
MT3000K
230
80
min-1
mm
mm
250
6.35 hex
4.0-6.0
min-1
8,500
min-1
8,500
kg
kg
kg
1.3
1.25
1.25
Protecting the environment
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your Black & Decker product
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product
available for separate collection.
7
EC declaration of conformity
MT3000K
Black & Decker declares that these products conform to:
98/37/EC, 89/336/EEC , 2002/95/EC, EN 60745 , EN 55014 ,
EN 61000
LpA (sound pressure) 80 dB(A), LWA (acoustic power) 91 dB(A),
hand/arm weighted vibration 6,1 m/s2
KpA (sound pressure uncertainty) 3 dB(A),
KWA (acoustic power uncertainty) 3 dB(A)
Kevin Hewitt
Director of Consumer Engineering
Spennymoor, County Durham DL16 6JG,
United Kingdom
1-12-2004
Guarantee
Black & Decker is confident of the quality of its products and
offers an outstanding guarantee. This guarantee statement is
in addition to and in no way prejudices your statutory rights.
The guarantee is valid within the territories of the Member
States of the European Union and the European Free Trade
Area.
If a Black & Decker product becomes defective due to faulty
materials, workmanship or lack of conformity, within 24 months
from the date of purchase, Black & Decker guarantees to
replace defective parts, repair products subjected to fair wear
and tear or replace such products to ensure minimum
inconvenience to the customer unless:
◆ The product has been used for trade, professional or hire
purposes;
◆ The product has been subjected to misuse or neglect;
◆ The product has sustained damage through foreign
objects, substances or accidents;
◆ Repairs have been attempted by persons other than
authorised repair agents or Black & Decker service staff.
To claim on the guarantee, you will need to submit proof of
purchase to the seller or an authorised repair agent. You can
check the location of your nearest authorised repair agent by
contacting your local Black & Decker office at the address
indicated in this manual. Alternatively, a list of authorised
Black & Decker repair agents and full details of our after-sales
service and contacts are available on the Internet at:
www.2helpU.com
8
Please visit our website www.blackanddecker.co.uk to
register your new Black & Decker product and to be kept up to
date on new products and special offers. Further information
on the Black & Decker brand and our range of products is
available at www.blackanddecker.co.uk
MT3000K
33
TYP
1
1
4
3
5
6
19
8
2
17
18
7
10
9
16
12
13
39
19
14
35
15
34
36
20
11
26
29
30
28
27
22
21
24
31
32
E14110
23
25
WWW.2helpU.com
19 - 01 - 05
9
10
11
Australia
Black & Decker (Australia) Pty. Ltd. Tel. 03-8720 5100
20 Fletcher Road, Mooroolbark,
Fax 03-9727 5940
Victoria, 3138
New Zealand
Black & Decker
81 Hugo Johnston Drive
Penrose, Auckland, New Zealand
United Kingdom
Black & Decker
210 Bath Road
Slough, Berkshire SL1 3YD
487779-00
12
Tel. 09 579 7600
Fax 09 579 8200
Tel. 01753 511234
Fax 01753 551155
Helpline 01753 574277
03/05
Download PDF