KW712 | Black&Decker KW712 PLANER Type 2 instruction manual

www.blackanddecker.co.uk
KW712
KW712KA
English
2
(Original instructions)
5
B
A
C
(KW712KA)
D
E
3
F
4
G
Intended use
3. Personal safety
Your BLACK+DECKER planer has been designed for planing wood, a. Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a power
wood products and plastics. The tool is intended for handtool while you are tired or under the influence of drugs,
held use. This tool is intended for consumer use only.
alcohol or medication. A moment of inattention while
operating power tools may result in serious personal injury.
Safety instructions
b. Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask,
General power tool safety warnings
non-skid safety shoes, hard hat, or hearing protection used
for appropriate conditions will reduce personal injuries.
Warning! Read all safety warnings and all
c. Prevent unintentional starting. Ensure the switch is in
instructions. Failure to follow the warnings and
the off-position before connecting to power source
instructions listed below may result in electric shock,
and/or battery pack, picking up or carrying the tool.
fire and/or serious injury.
Carrying power tools with your finger on the switch or
energising power tools that have the switch on invites
Save all warnings and instructions for future reference.
accidents.
The term "power tool" in all of the warnings listed below refers
d. Remove any adjusting key or wrench before turning
to your mains operated (corded) power tool or battery operated
the power tool on. A wrench or a key left attached to
(cordless) power tool.
a rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance at
1. Work area safety
all times. This enables better control of the power tool in
a. Keep work area clean and well lit. Cluttered or dark areas
unexpected situations.
invite accidents.
f. Dress properly. Do not wear loose clothing or jewellery.
b. Do not operate power tools in explosive atmospheres,
Keep your hair, clothing and gloves away from moving
such as in the presence of flammable liquids, gases
parts. Loose clothes, jewellery or long hair can be caught
or dust. Power tools create sparks which may ignite the
in moving parts.
dust or fumes.
g. If devices are provided for the connection of dust
c. Keep children and bystanders away while operating
extraction and collection facilities, ensure these are
a power tool. Distractions can cause you to lose control.
connected and properly used. Use of dust collection can
reduce dust-related hazards.
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify
4. Power tool use and care
the plug in any way. Do not use any adapter plugs
a. Do not force the power tool. Use the correct power tool
with earthed (grounded) power tools. Unmodified plugs
for your application. The correct power tool will do the
and matching outlets will reduce risk of electric shock.
job better and safer at the rate for which it was designed.
b. Avoid body contact with earthed or grounded surfaces
b. Do not use the power tool if the switch does not turn it
such as pipes, radiators, ranges and refrigerators.
on and off. Any power tool that cannot be controlled with
There is an increased risk of electric shock if your body is
the switch is dangerous and must be repaired.
earthed or grounded.
c. Disconnect the plug from the power source and/or the
c. Do not expose power tools to rain or wet conditions.
battery pack from the power tool before making any
Water entering a power tool will increase the risk of electric
adjustments, changing accessories, or storing power
shock.
tools. Such preventive safety measures reduce the risk of
d. Do not abuse the cord. Never use the cord for carrying,
starting the power tool accidentally.
pulling or unplugging the power tool. Keep cord away
d. Store idle power tools out of the reach of children and
from heat, oil, sharp edges or moving parts. Damaged
do not allow persons unfamiliar with the power tool or
or entangled cords increase the risk of electric shock.
these instructions to operate the power tool. Power tools
e. When operating a power tool outdoors, use an
are dangerous in the hands of untrained users.
extension cord suitable for outdoor use. Use of a cord
e. Maintain power tools. Check for misalignment or binding
suitable for outdoor use reduces the risk of electric shock.
of moving parts, breakage of parts and any other
f. If operating a power tool in a damp location is
condition that may affect the power tools operation.
unavoidable, use a residual current device (RCD)
If damaged, have the power tool repaired before use.
protected supply. Use of an RCD reduces the risk of
Many accidents are caused by poorly maintained power tools.
electric shock.
@
5
f. Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to bind
and are easier to control.
g. Use the power tool, accessories and tool bits etc., in
accordance with these instructions, taking into account
the working conditions and the work to be performed.
Use of the power tool for operations different from those
intended could result in a hazardous situation.
5. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
Additional power tool safety warnings
@
Warning! Additional safety warnings for planers
Hold the tool by the insulated gripping surfaces when
performing an operation where the cutting tool may
contact hidden wiring or its own cord. Cutting accessory
contacting a "live" wire may make exposed metal parts of
the power tool "live" and shock the operator.
u Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding the
work by hand or against your body leaves it unstable and
may lead to loss of control.
u Wait for the cutter to stop before setting the tool down.
An exposed cutter may engage the surface leading to
possible loss of control and serious injury.
u Keep the cutter sharp. Dull or damaged cutters may cause
the planer to swerve or stall under pressure. Always use
the appropriate type of cutter for the power tool.
u Do not touch the workpiece or the cutter immediately after
operating the tool. They can become very hot.
u Remove all nails and metal objects from the workpiece
before planning.
u Always hold the tool with both hands and by the handles
provided.
u Immediately disconnect the cable from the mains if it is
damaged or cut.
Warning! Contact with, or inhalation of dusts arising from
planing applications may endanger the health of the operator
and possible bystanders. Wear a dust mask specifically
designed for protection against dust and fumes and ensure
that persons within or entering the work area are also protected.
u
6
This tool is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not
play with the appliance.
u The intended use is described in this instruction manual.
The use of any accessory or attachment or performance of
any operation with this tool other than those recommended
in this instruction manual may present a risk of personal
injury and/or damage to property.
u
Safety of others
This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety.
u Children should be supervised to ensure that they do not
play with the appliance.
u
Vibration
The declared vibration emission values stated in the technical
data and the declaration of conformity have been measured in
accordance with a standard test method provided by EN 60745
and may be used for comparing one tool with another.
The declared vibration emission value may also be used in
a preliminary assessment of exposure.
Warning! The vibration emission value during actual use of
the power tool can differ from the declared value depending
on the ways in which the tool is used. The vibration level may
increase above the level stated.
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons regularly
using power tools in employment, an estimation of vibration
exposure should consider, the actual conditions of use and the
way the tool is used, including taking account of all parts of the
operating cycle such as the times when the tool is switched off
and when it is running idle in addition to the trigger time.
Labels on tool
:
The following pictograms are shown on the tool:
Warning! To reduce the risk of injury, the user must
read the instruction manual.
Electrical safety
#
u
u
u
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Features
This tool includes some or all of the following features.
1. On/off switch
2. Lock-off button
3. Shavings discharge outlet
4. Planing depth adjustment knob
5. Planing depth graduation
Assembly
Warning! Before assembly, make sure that the tool is switched off
and unplugged.
Replacing the cutting blades (fig. A)
The cutting blades provided with this tool are reversible.
Replacement cutting blades can be obtained from your local
retailer.
Removing
u Loosen the bolts (6) using the spanner supplied.
u Slide the blade (7) out of the holder.
u Reverse the blade so that the unused side comes in position.
If both sides are worn, the blade must be replaced.
Fitting
u Slide the blade into the holder until it is against the end stop.
u Tighten the bolts using the spanner supplied.
Warning! Always replace both cutters.
Adjusting the depth of cut (fig. B)
The depth of cut is indicated by the marking (8). The setting
range can be read from the graduation (5).
u Turn the planing depth adjustment knob (4) to the required
depth of cut.
u Turn the knob to the ‘P' postion whenever the tool is not in
use.
KW712KA Fitting and removing the parallel fence
(fig. C)
The parallel fence is used to for optimum control on narrow
workpieces.
u Loosen the locking knob (9).
u Insert the parallel fence (11) through the opening (10).
u Slide the parallel fence into the desired position.
Tighten the locking knob.
To remove the parallel fence proceed in reverse order.
Connecting a vacuum cleaner to the tool (fig. D)
An adaptor is required to connect a vacuum cleaner or dust
extractor to the tool. The adaptor can be purchased from your
u
u
Slide the adaptor (12) over the shavings discharge outlet (3).
Connect the vacuum cleaner hose (13) to the adaptor.
Assembling and fitting the shavings collection bag
(fig. E)
The shavings collection bag is particularly useful when working
in
confinedtospaces.
extractor
the tool. The bag can be purchased from your
local BLACK+DECKER retailer.
Before first use, you will have to assemble the shavings
collection bag.
u Fit the wire frames (14) to the connecting plate (15) using
the screws (16) and washers (17).
u Pull the cloth bag (18) over the frame structure as shown.
Take care that the elasticated mouth (19) is well fitted
around the edge of the connecting plate (15).
u Slide the connecting plate over the shavings discharge
outlet (3).
Residual risks.
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
u Injuries caused by touching any rotating/moving
parts.
u Injuries caused when changing any parts, blades or
accessories.
u Injuries caused by prolonged use of a tool. When
using any tool for prolonged periods ensure you take
regular breaks.
u Impairment of hearing.
u Health hazards caused by breathing dust developed
when using your tool (example:- working with wood,
especially oak, beech and MDF.)
Use
Warning! Let the tool work at its own pace. Do not overload.
u Adjust the depth of cut.
u If necessary, fit and adjust the parallel fence.
7
Switching on and off
Switching on
u Keep the lock-off button (2) depressed and press the on/off
switch (1).
u Release the lock-off button.
Switching off
u Release the on/off switch.
Planing
Hold the tool with the nose piece of the shoe resting on
top of the workpiece surface.
u Switch the tool on.
u Move the tool steadily forward to perform the cutting stroke.
u Switch the tool off after the stroke has been completed.
u
Rebating (fig. F)
u
u
Fit and adjust the parallel fence. (KW712KA ONLY)
Proceed as for planing.
Chamfering edges
The V-groove in the nose piece of the shoe enables you to
chamfer edges at 45° angles.
u Hold the tool at an angle with the groove around the edge
of the workpiece and perform the cutting stroke.
- High-speed steel reversible cutting blades
(part no. X24192-XJ11, supplied per pair)
Maintenance
Your tool has been designed to operate over a long period of
time with a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular cleaning.
Warning! Before performing any maintenance, switch off and
unplug the tool.
u Regularly clean the ventilation slots in your tool using a soft
brush or dry cloth.
u Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
Replacing the drive belt (fig. G)
Loosen the screws (20) and remove the cover (21).
Remove the old drive belt.
u Place the new belt (22) over the pulleys. Place the belt
over the large pulley (23) first, then over the small pulley
(24), whilst manually rotating the belt steadily.
u Put the cover back in place and tighten the screws.
u
u
Mains plug replacement (U.K. & Ireland only)
Emptying the shavings collection bag
The shavings collection bag should be emptied regularly while
using it.
u Unzip the bag and empty it before continuing.
If a new mains plug needs to be fitted:
u Safely dispose of the old plug.
u Connect the brown lead to the live terminal in the new plug.
u Connect the blue lead to the neutral terminal.
Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 5 A.
Hints for optimum use
Protecting the environment
Move the tool along the grain of the wood.
u If the grain is cross or curly, or if the workpiece material is
a hard type of wood, adjust the depth of cut to take only
a very thin shaving at each pass and take several passes
to achieve the desired result.
u To keep the tool in a straight line, press down the front of
the tool at the start, and press down the back of the tool at
the end of the cutting stroke.
u
Accessories
The performance of your tool depends on the accessory used.
BLACK+DECKER and Piranha accessories are engineered to
high quality standards and designed to enhance the performance
of your tool. By using these accessories you will get the very
best from your tool.
The following types of cutting blades can be obtained from
your local retailer:
- Tungsten carbide tipped reversible cutting blades
(part no. X35007, supplied per pair)
8
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your BLACK+DECKER product
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product available
for separate collection.
z
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand for
raw materials.
Local regulations may provide for separate collection of
electrical products from the household, at municipal waste
sites or by the retailer when you purchase a new product.
BLACK+DECKER provides a facility for the collection and
recycling of BLACK+DECKER products once they have reached
the end of their working life. To take advantage of this service
please return your product to any authorised repair agent who
will collect them on our behalf.
You can check the location of your nearest authorised repair
agent by contacting your local BLACK+DECKER office at the
address indicated in this manual. Alternatively, a list of
authorised BLACK+DECKER repair agents and full details of our
after-sales service and contacts are available on the Internet
at: www.2helpU.com
Technical data
Input voltage
VAC
Power input
W
No-load speed
min-1
Planing width
mm
Planing depth
mm
Rebating depth
mm
Weight
kg
KW712/KW712KA TYPE2
230
650
17,000
82
2
8
3
EC declaration of conformity
%
MACHINERY DIRECTIVE
KW712/KW712KA
Black & Decker declares that these products described under
"technical data" are in compliance with:
2006/42/EC, EN 60745-1, EN 60745-2-14
These products also comply with Directive
2004/108/EC and 2011/65/EU. For more information,
These products also comply with Directive 2014/30/EU and
2011/65/EU. For more information, please contact Black &
Decker at the following address or refer to the back of the
manual.
The undersigned is responsible for compilation of the technical
file and makes this declaration on behalf of Black & Decker.
Vibration total values (triax vector sum) according to EN 60745:
Vibration emission value (ah) 2.6 m/s2, uncertainty (K) 1.5 m/s2
Level of sound pressure according to EN 60745:
Sound pressure (LpA) 90 dB(A), uncertainty (K) 3 dB(A)
Sound power (LWA) 105 dB(A), uncertainty (K) 3 dB(A)
R. Laverick
Engineering Manager
Black & Decker Europe, 210 Bath Road, Slough,
Berkshire, SL1 3YD
United Kingdom
12/11/2014
9
Guarantee
Black & Decker is confident of the quality of its products and
offers an outstanding guarantee. This guarantee statement is
in addition to and in no way prejudices your statutory rights.
The guarantee is valid within the territories of the Member States
of the European Union and the European Free Trade Area.
If a Black & Decker product becomes defective due to faulty
materials, workmanship or lack of conformity, within 24 months
from the date of purchase, Black & Decker guarantees to
replace defective parts, repair products subjected to fair wear
and tear or replace such products to ensure minimum
inconvenience to the customer unless:
u The product has been used for trade, professional or hire
purposes;
u The product has been subjected to misuse or neglect;
u The product has sustained damage through foreign objects,
substances or accidents;
u Repairs have been attempted by persons other than
authorised repair agents or Black & Decker service staff.
To claim on the guarantee, you will need to submit proof of
purchase to the seller or an authorised repair agent. You can
check the location of your nearest authorised repair agent by
contacting your local Black & Decker office at the address
indicated in this manual. Alternatively, a list of authorised
Black & Decker repair agents and full details of our after-sales
service and contacts are available on the Internet at:
www.2helpU.com
Please visit our website www.blackanddecker.co.uk
to register your new BLACK+DECKER product and to be kept up
to date on new products and special offers.
Further information on the BLACK+DECKER brand and our range
of products is available at www.blackanddecker.co.uk
10
Australia
New Zealand
Black & Decker (Australia) Pty. Ltd.
20 Fletcher Road, Mooroolbark,
Victoria, 3138
Tel. Fax 03-8720 5100
03-9727 5940
Black & Decker
5 Te Apunga Place
Mt Wellington
Aukland 1060
Tel. Fax +64 9 259 1133
+64 9 259 1122
United Kingdom &
Black & Decker
Tel. 01753 511234
Republic Of Ireland
210 Bath Road
Fax 01753 512365
www.blackanddecker.co.uk Slough, Berkshire SL1 3YD
emeaservice@sbdinc.com
90618946 REV-0
11/2014
Download PDF