KD650 | Black&Decker KD650 ROTARY HAMMER Type 2 instruction manual

www.blackanddecker.co.uk
8
6
7
5
3
4
1
2
UK
Ireland
Australia
New Zealand
1
9
8
7
A
10
6
11
13
12
6
C
B
16
15
14
17
5
D
2
13
E
11
8
9
F
3
Intended use
Your Black & Decker rotary hammer drill has been designed
for drilling in wood, metal, plastics, and masonry as well as
for screwdriving and light chiselling applications.
This tool is intended for consumer use only.
General safety rules
Warning! Read all instructions. Failure to follow all instructions
listed below may result in electric shock, fire and/or serious
injury. The term “power tool” in all of the warnings listed
below refers to your mains operated (corded) power tool or
battery operated (cordless) power tool.
SAVE THESE INSTRUCTIONS.
1. Work area
a. Keep work area clean and well lit. Cluttered and dark
areas invite accidents.
b. Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases
or dust. Power tools create sparks which may ignite the
dust or fumes.
c. Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs
with earthed (grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock
if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase the
risk of electric shock.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use
common sense when operating a power tool. Do not
use a power tool while you are tired or under the
influence of drugs, alcohol or medication. A moment
of inattention while operating power tools may result in
serious personal injury.
4
b. Use safety equipment. Always wear eye protection.
Safety equipment such as dust mask, non-skid safety
shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
c. Avoid accidental starting. Ensure the switch is in
the off position before plugging in. Carrying power
tools with your finger on the switch or plugging in power
tools that have the switch on invites accidents.
d. Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power tool
in unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these
are connected and properly used. Use of these
devices can reduce dust related hazards.
4. Power tool use and care
a. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will do
the job better and safer at the rate for which it was
designed.
b. Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
c. Disconnect the plug from the power source before
making any adjustments, changing accessories, or
storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users.
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc.,
in accordance with these instructions and in the
manner intended for the particular type of power
tool, taking into account the working conditions
and the work to be performed. Use of the power tool
for operations different from those intended could result
in a hazardous situation.
5. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Additional safety instructions for hammer drills
◆ Wear ear protectors. Exposure to noise can cause
hearing loss.
◆ Use auxiliary handles supplied with the tool. Loss of
control can cause personal injury.
◆ Preferably wear a dust mask.
Electrical safety
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
◆
◆
This appliance is not intended for use by young or infirm
persons without supervision. Children must be supervised
to ensure they do not play with the appliance.
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
◆
◆
◆
◆
Slacken the knob (9).
Insert the depth stop (8) into the mounting hole as shown.
Set the depth stop to the desired position. The maximum
drilling depth is equal to the distance between the tip of
the drill bit and the front end of the depth stop.
Tighten the knob (9).
Fitting an accessory (fig. B)
◆ Clean and grease the shank (10) of the accessory.
◆ Pull back the sleeve (11) and insert the shank into the tool
holder (6).
◆ Push the accessory down and turn it slightly until it fits
into the slots.
◆ Pull on the accessory to check if it is properly locked.
The hammering function requires the accessory to be able
to move axially several centimetres when locked in the
tool holder.
◆ To remove the accessory, pull back the sleeve (11) and
pull out the accessory.
Fitting the keyed chuck (fig. C)
◆ Fit the shank (12) of the supplied chuck (13) into the tool
holder as described above.
Warning! Never use standard chucks in the hammer drilling
mode.
Fitting accessories in the keyed chuck (fig. D)
◆ Open the chuck by turning the sleeve (14).
◆ Insert the bit shaft (15) into the chuck.
◆ Insert the chuck key (16) into each hole (17) in the side of
the chuck and turn until tight.
Features
Use
This tool includes some or all of the following features.
1. Variable speed switch
2. Lock-on button
3. Forward/reverse switch
4. Variable speed control knob
5. Drilling mode selector
6. Tool holder
7. Side handle
8. Depth stop
Warning! Let the tool work at its own pace. Do not overload.
Assembly
Drilling
◆ For drilling in steel, wood and plastics, and for
screwdriving set the operating mode selector (5) to the
position.
◆ When screwdriving, start at a low speed. When removing
screws, the speed is automatically reduced.
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting the side handle and depth stop (fig. A)
◆ Turn the grip counterclockwise until you can slide the side
handle (7) onto the front of the tool as shown.
◆ Rotate the side handle into the desired position.
◆ Tighten the side handle by turning the grip clockwise.
Warning! Before drilling into walls, floors or ceilings, check
for the location of wiring and pipes.
Selecting the operating mode (fig. E)
The tool can be used in three operating modes. Rotate the
drilling mode selector (5) towards the required position,
as indicated by the symbols.
5
Hammer drilling
◆ For hammer drilling in masonry and concrete, set the
operating mode selector (5) to the
position
◆ When hammering, the tool should not bounce and run
smoothly. If necessary, increase the speed.
Hammering
◆ For hammering with spindle lock, and for light chiselling
and chipping, set the operating mode selector (5) to the
position.
◆ Make sure the forward/reverse switch is in the forward
position.
◆ When changing from hammer drilling to chiselling,
turn the chisel to the desired position. If resistance is felt
during mode change, slightly turn the chisel to engage the
spindle lock.
Selecting the direction of rotation
For drilling, for tightening screws and for chiselling, use
forward (clockwise) rotation. For loosening screws or removing
a jammed drill bit, use reverse (counterclockwise) rotation.
◆ To select forward rotation, push the forward/reverse
slider (3) to the left.
◆ To select reverse rotation, push the forward/reverse slider
to the right.
Warning! Never change the direction of rotation while the
motor is running.
Setting the drilling depth (fig. F)
◆ Slacken the knob (9).
◆ Set the depth stop (8) to the desired position. The maximum
drilling depth is equal to the distance between the tip of
the drill bit and the front end of the depth stop.
◆ Tighten the knob (9).
Switching on and off
◆ To switch the tool on, press the variable speed switch (1).
The tool speed depends on how far you press the switch.
Set the variable speed control knob (4) to the required
speed range. As a general rule, use low speeds for large
diameter drill bits and high speeds for smaller diameter
drill bits.
◆ For continuous operation, press the lock-on button (2) and
release the variable speed switch. This option is available
only in forward (clockwise) rotation.
◆ To switch the tool off, release the variable speed switch.
To switch the tool off when in continuous operation,
press the variable speed switch once more and release it.
6
Accessories
The performance of your tool depends on the accessory used.
Black & Decker and Piranha accessories are engineered to
high quality standards and designed to enhance the performance
of your tool. By using these accessories you will get the very
best from your tool.
Maintenance
Your tool has been designed to operate over a long period of
time with a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular cleaning.
◆ Regularly clean the ventilation slots with a clean,
dry paint brush.
◆ To clean the tool, use only mild soap and a damp cloth.
Never let any liquid get inside the tool and never immerse
any part of the tool into liquid.
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
◆ Safely dispose of the old plug.
◆ Connect the brown lead to the live terminal in the new
plug.
◆ Connect the blue lead to the neutral terminal.
Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality
plugs. Recommended fuse: 5 A.
Protecting the environment
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your Black & Decker product
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product
available for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand for
raw materials.
Local regulations may provide for separate collection of
electrical products from the household, at municipal waste
sites or by the retailer when you purchase a new product.
Black & Decker provides a facility for the collection and
recycling of Black & Decker products once they have reached
the end of their working life. To take advantage of this service
please return your product to any authorised repair agent who
will collect them on our behalf.
You can check the location of your nearest authorised repair
agent by contacting your local Black & Decker office at the
address indicated in this manual. Alternatively, a list of
authorised Black & Decker repair agents and full details of our
after-sales service and contacts are available on the Internet
at: www.2helpU.com
◆
◆
◆
◆
The product has been used for trade, professional or hire
purposes;
The product has been subjected to misuse or neglect;
The product has sustained damage through foreign
objects, substances or accidents;
Repairs have been attempted by persons other than
authorised repair agents or Black & Decker service staff.
Technical data
Voltage
Power input
No-load speed
Impact rate
Impact energy
Max. drilling capacity
Concrete
Steel
Wood
Weight
VAC
W
min-1
min-1
J
mm
mm
mm
kg
KD650
230
600
0 - 900
0 - 4,850
1.8
KD70
230
700
0 - 900
0 - 4,850
2.2
KD960
230
750
0 - 900
0 - 4,850
2.2
20
13
30
3.5
20
13
30
3.5
20
13
30
3.5
EC declaration of conformity
KD650/KD70/KD960
Black & Decker declares that these products conform to:
98/37/EC, 89/336/EEC, EN 55014, EN 60745, EN 61000
To claim on the guarantee, you will need to submit proof of
purchase to the seller or an authorised repair agent. You can
check the location of your nearest authorised repair agent by
contacting your local Black & Decker office at the address
indicated in this manual. Alternatively, a list of authorised
Black & Decker repair agents and full details of our after-sales
service and contacts are available on the Internet at:
www.2helpU.com
Please visit our website www.blackanddecker.co.uk to
register your new Black & Decker product and to be kept up to
date on new products and special offers. Further information
on the Black & Decker brand and our range of products is
available at www.blackanddecker.co.uk
LpA (sound pressure) 95 dB(A), LWA (acoustic power) 106 dB(A),
hand/arm weighted vibration 4.62 m/s2
KpA (sound pressure uncertainty): 3 dB(A),
KWA (acoustic power uncertainty) 3 dB(A)
Kevin Hewitt
Director of Consumer Engineering
Spennymoor, County Durham DL16 6JG,
United Kingdom
1-1-2005
Guarantee
Black & Decker is confident of the quality of its products and
offers an outstanding guarantee. This guarantee statement is
in addition to and in no way prejudices your statutory rights.
The guarantee is valid within the territories of the Member
States of the European Union and the European Free Trade
Area.
If a Black & Decker product becomes defective due to faulty
materials, workmanship or lack of conformity, within 24 months
from the date of purchase, Black & Decker guarantees to
replace defective parts, repair products subjected to fair wear
and tear or replace such products to ensure minimum
inconvenience to the customer unless:
7
KD70KC - KD650K - KD960K
15
16
9
35 34
30
32
33
51
49
79
8
60
61
60
71
69
77
84
E14776
63
68
70
75
85 76
81
64
60
44
62
62
83
59
60
43
800
57
55
52 53 54
50
42
45
56
23
82
47
46
24
25
29
31
48
58
18
28 27 26
36
21
14
7 12
10
39
78
38
37
40 41
1 86
22
8
2 3 4
20
11 13
5
6
19
17
TYP
2
74
73
77
72
www.2helpU.com
65
80
67
20-06-06
66
9
10
11
Australia
Black & Decker (Australia) Pty. Ltd. Tel. 03-8720 5100
20 Fletcher Road, Mooroolbark,
Fax 03-9727 5940
Victoria, 3138
New Zealand
Black & Decker
81 Hugo Johnston Drive
Penrose, Auckland, New Zealand
United Kingdom
Black & Decker
210 Bath Road
Slough, Berkshire SL1 3YD
584662-00
12
Tel. 09 579 7600
Fax 09 579 8200
Tel. 01753 511234
Fax 01753 551155
Helpline 01753 574277
06/06
Download PDF

advertising