BX380G | Black&Decker BX380G BLENDER instruction manual

Blender, Coffee Grinder & Cheese Grater
First Use Safety Recommendation
Please read through this booklet for safe and efficient use of the appliance.
We urge you to read the "Hint's" section and also follow all detailed
instructions even if you are familiar with using this appliance.
Keep this guide handy for future reference.
Page 02
Page 15
Page 23
While using electrical appliances, in order to reduce the risk of fire, electric shock,
and/or injury to persons, basic safety precautions should be followed, including the
• Read all instructions carefully, even if you are familiar with the appliance.
• To protect against the risk of electric shock, DO NOT IMMERSE the appliance,
cord set or plug in water or other liquids.
• To clean, wipe the exterior with a damp cloth.
• Close supervision is necessary when any appliance is used near children. Never
leave an appliance unattended when in use.
• If the supply cord is damaged, it must be replaced by the manufacturer or its
service agent or a similarly qualified person in order to avoid a hazard.
• Switch off and remove the plug from the power outlet when not in use before
assembling or disassembling parts, cleaning or carrying out any maintenance of
the appliance. Never pull the cord while unplugging out from power outlet.
• Do not operate the appliance if it's damage in any manner. Return the complete
appliance to your nearest authorized service facility for examination, electrical
repair, mechanical repair or adjustments to avoid any hazard.
• The use of attachments or accessories not recommended or sold by this
appliance manufacturer may result in fire, electric shock or personal injury.
• Do not let the cord hang over the edge of a table, counter, or touch hot surfaces.
• Avoid touching hot surfaces, use handles and knobs.
• Do not operate or place any part of this appliance on or near any hot surfaces
(such as gas or electric burner or in a heated oven).
• Do not abuse the cord. Never carry the appliance by the cord or yank it to
disconnect it from the outlet; instead, grasp the plug and pull to disconnect.
• When using an extension cord with your appliance, make sure the extension cord
is correctly wired, and rated for its use.
• This product is intended for household use only.
• Do not attempt to repair the appliance yourself; instead, take it to your Black &
Decker-owned or Authorized Service Centre for repair.
Parts Identification
1 Filler Cap
2 Lid
3 Jar
4 Blade Assembly
5 Seal
6 Jar Base
7 Motor Housing
8 Switch
9 Cord Set
10 Feet
11 Coffee Grinder
12 Cheese Grater
13 Grinder Cover
14 Grater Cover
Intended Use
Your Black & Decker Blender has been
designed for processing ingredients as
listed in this manual.
This appliance is intended for indoor
consumer use only.
Safety Instructions
Warning! When using mains-powered
appliances, basic safety precautions,
including the following, should always be
followed to reduce the risk of fire, electric
shock, personal injury and material
• Read all of this manual carefully before
using the appliance.
• The intended use is described in this
manual. The use of any accessory or
attachment or the performance of any
operation with this appliance other than
those recommended in this instruction
manual may present a risk of personal
• Disconnect the appliance from the power
supply when not in use, before fitting or
removing parts, maintenance and before
• Surfaces may be hot during use and
during the cool down period.
• Do not operate or place any part of this
appliance on or near any hot surface,
such as a gas or electric burner or in a
heated oven.
• When using an extension cord with your
appliance, make sure the extension cord
is correctly wired and rated for its use.
Safety of others
• Do not allow children or any person
unfamiliar with these instructions to use
the appliance.
• Do not allow children or animals to come
near the work area or to touch the
appliance or power supply cord. Close
supervision is necessary when the
appliance is used near children.
• Never leave an appliance unattended
when in use.
• Retain this manual for future reference.
• Do not allow the cord set to hang over
• Always route the cord carefully to avoid a
bench tops.
tripping hazard.
• This appliance is not intended for use by
• Never operate an appliance directly
persons (including children) with reduced
below the socket-outlet it is connected
physical, sensory or mental capabilities,
or lack of experience and knowledge,
unless they have been given supervision
Using your appliance
or instruction concerning use of the
• Make sure that the appliance is switched
appliance by a person responsible for
off before connecting to or disconnecting
their safety.
from the power supply.
• Children should be supervised to ensure
• Always take care when using the
that they do not play with the appliance.
After use
• Do not use the appliance outdoors.
• Switch off and remove the plug from the
• Never pull the power supply cord to
socket before leaving the appliance
disconnect the plug from the socket.
unattended and before changing,
Keep the power supply cord away from
cleaning or inspecting any parts of the
heat, oil and sharp edges.
Additional Safety Instructions for
• When not in use, the appliance should be
stored in a dry place. children should not
• Do not immerse the appliance, cord set
have access to stored appliances.
or plug in liquids
Inspection and repairs
• Always leave sufficient space around the
• Before use, check the appliance for
appliance for ventilation.
damaged or defective parts. Check for
• Keep loose clothing, hair, jewellery, etc.
breakage of parts, damage to switches
away from moving parts.
and any other conditions that may affect • Do not use the unit if you have wet hands
its operation.
or bare feet.
• Do not use the appliance if any part is
• Care is needed when handling cutting
damaged or defective.
blades, especially when removing the
blades, emptying, and during cleaning.
• Have any damaged or defective parts
• Switch off the appliance before changing
repaired or replaced by an authorized
accessories or approaching parts which
repair agent.
move in use.
• Before use, check the power supply cord
for signs of damaged, ageing and wear.
This appliance requires some assembly to
• Do not use the appliance if the power
complete the required task. Please refer to
supply cord or main plug is damaged or
the relevant section for particular assembly
details. All parts should be cleaned before
• If the supply cord is damaged, it must be use. see "Cleaning" for details.
replaced by the manufacturer or its
service agent or a similarly qualified
As a Blender
person in order to avoid a hazard.
Place the appliance on a clean, flat work
• Do not cut the power supply cord and do surface.
not attempt to repair it yourself.
Assemble the jar (3) by first placing the
sealing ring (5) on the blade assembly (4).
• Never attempt to remove or replace any
Position the blade assembly in the jar base
parts other than those specified in this
(6). Fit the jar base (6) into the jar (3),
rotating it in an anti-clockwise direction until
• Do not attempt to repair the appliance.
Take it to your nearest Black & Decker owned or authorized Services Centre for Warning! Do not over-tighten.
Place the assembled jar on the motor
housing (7) and rotate it in a clockwise
Double Insulation
direction until it locks in position.
This appliance is double insulated;
To unlock rotate it in anticlockwise direction
therefore no earth wire is required.
until it unlocks in position.
Always check that the power supply
Add the ingredients to the jar then fit the lid
corresponds to the voltage on the rating
(2) and filter cap (1). The filter cap must be
rotated clockwise to lock it in place.
Note: Do not exceed the maximum
and rotating the cover in an anti-clockwise
capacity of 1.5 litres.
direction. Add a maximum of 40g of coffee
beans to the cup. Place the cover on the
Connect the appliance to a suitable
cup & rotate it clockwise until it locks in
electrical supply. Rotate the switch (8) to
place. Position the assembly on the motor
the required speed. Pulse (P) can also be
used to give greater control. When blending
is complete, either release the pulse button,
or return the switch to the off (0) position.
housing (7), rotate it clockwise until it locks
into place. Turn the knob to the required
speed & allow the grinder to operate.
Once the blades have come to a complete
Note: The Coffee Grinder should not be run
stop, rotate the jar (3) in an anti-clockwise
for longer than 20 seconds. After each 20
direction and lift it from the motor housing
seconds use, the Coffee Grinder must be
(7). Remove the lid (2). Pour the ingredients
allowed to cool down for a least 3 minutes.
into a suitable container.
This can be repeated 3 times before further
Note: Ingredients can be added by inserting
them through the hole left when the filler
use, the unit must be left to cool to room
cap (1) is removed.
As a Cheese Grater
Warning! Never operate the Blender
Cheese should be cut into 15 mm cubes
without the lid (2) fitted.
before grinding. Remove the cover (14) from
Note: The blender will not operate unless
the cheese grating attachment (12) by
the lid is correctly fitted.
holding the cup & rotating the cover in an
anti-clockwise direction. Add the prepared
Note: Do not operate the blender for longer
than 2 minutes. After each 2 minute session
the blender must be allowed to cool down
cheese to the cup. Place the cover on the
cup & rotate it clockwise until it locks in
place. Position the assembly on the motor
for at least 10 minutes.
housing (7), rotating it clockwise until it
Note: The motor is equipped with an auto
locks into place. Turn the knob to the
resetting thermostat. This may operate and
required speed & allow the grater to
stop blending if the appliance is over
loaded. If this should happen, allow the
Note: The Cheese Grater should not be run
blender to cool down and remove some of
for longer than 20 seconds. After each 20
the contents of the jar. The thermostat will
seconds use, the Cheese Grater must be
take a few minutes to reset.
allowed to cool down for at least 3 minutes.
As a Coffee Grinder
This can be repeated 3 times before further
Remove the cover (13) from the coffee
use, the unit must be left to cool to room
grinding attachment (11) by holding the cup
Food Guide
25-35 sec
2 or 3, Pulse
1.5 Litre
Semi Liquids
15-20 sec
1, Pulse
1 Litre
Pepper/Coffee beans
10-20 sec
1, Pulse
40 gms
20-30 sec
1, Pulse
50 gms
Hard Cheese
10-20 sec
1, Pulse
40 gms*
Soft Cheese
20-30 sec
1, Pulse
50 gms*
*Cut into 15mm x 15mm
Do not operate the appliance continuously
for more than 2 minutes. After operating
continuously for 2 minutes, let it cool down
for at least 10 minutes before operating it
The motor housing should be cleaned with
a clean damp cloth only. The jar and
grinding attachments can be washed in
warm soapy water. Rinse with clean water
and dry thoroughly with a dry soft cloth.
Your Black & Decker tool has been
Note: Do not use abrasives or chemical
designed to operate over a long period of
cleaners on any part of this appliance.
time with a minimum of maintenance.
Continuous satisfactory operation depends
Note: take care when handling the blades,
they are sharp and cannot be dismantled.
upon proper tool care and regular cleaning.
Warning! Before performing any
maintenance or cleaning of the tool,
disconnect the appliance from the power
supply. Ventilation slots should be cleaned
occasionally with a clean, dry paint brush.
Protecting the environment
Separate collection. This product must not be disposed of with normal household
Should you find one day that your Black & Decker product needs replacement, or if it is of no
further use to you, do not dispose it off with other household waste. Make this product
available for separate collection.
Separate collection of used products and packaging allows materials to be recycled
and used again. Use of recycled materials helps prevent environmental pollution and
reduces the demand for raw materials.
Local regulations may provide for separate collection of electrical products from the
household, at municipal waste sites or by the retailer when you purchase a new product.
Black & Decker provides a facility for the collection and recycling of Black & Decker products
once they have reached the end of their working life. To take advantage of this service please
return your product to any authorised repair agent who will collect them on our behalf. You
can check the location of your nearest authorised repair agent by contacting your local Black
& Decker office at the address indicated in this manual. A list of authorised Black & Decker
repair agents and full details of our after-sales service and contact are available on the Internet
at: www.2helpU.com
Black & Decker provides a 2 Year Warranty for this product from the date of purchase against defects due
to defective materials or workmanship. Motor/element burn-outs due to voltage fluctuations are not
covered under warranty. If the product should become defective within the warranty period, Black &
Decker will repair or (at Black & Decker's discretion) replace it free of charge.
The warranty provisions do not cover failure due to accident, misuse, abuse, negligence or non
observation of local regulations on the part of the user. Equally, the warranty provisions do not apply
where the appliance has been serviced by a person not authorized by Black & Decker or serviced with
non-approved parts and this has contributed to the fault of the product. Superseded models without a
replacement equivalent will either be repaired or (at Black & Decker's discretion) replaced with another
product of similar retail value.
Fill in the Warranty Registration Card with the original Authorized Dealer's stamp (indicating date of
purchase) and attach your purchase receipt to it. Retain in case of claims in the future.
Take your defective product together with the Warranty Registration Card & purchase receipt to your local
service Centre. You can either do this in person or send it freight prepaid. If mailing or shipping your
appliance, ensure that it is packed carefully in a sturdy carton with enough packing material to prevent
damage. Include a note describing the problem to the service Centre and be sure to give your return
Afghanistan: Ishan National Co., Opp. Ministry of Justice, Kabul. Tel.: +93-2-2101727. Algeria: SARL Outillage Corporation, 04
Route De Dely Brahim Cheraga, Alger. Tel.: +213-21-364363/508, Fax: +213-21-369667. Bahrain: Fawaz Al Zayani, P.O.Box 26563,
Adliya, Manama. Tel.: +973-17-715252/712756, Fax: +973-17-713789. Bangladesh: Ultra Corporation, 8, Kushol Centre, Uttara,
Dhaka 1230. Tel.: +880-2-8919272/9756 Ext.28, Fax: +880-2-9887167. Egypt: Anasia Egypt for Trading S. A. E., P.O.Box 2443, 110
Mostafa Refaat Street, Sheraton Heliopolis 11361, Cairo. Tel.: +20-2-2684159, Fax: +20-2-2684169. Ethiopia: Tewfik Sherif & Co.
Ltd., P.O.Box 5583, Debre Zeit Road, Addis Ababa. Tel.: +251-1-651700/601, Fax: +251-1-650570. India: Gryphon Impex Pvt. Ltd.,
D-6/4, Okhla Industrial Area, Phase-I, New Delhi-110020. Tel.: +91-11-26372602-4, Fax: +91-11-26372601. Iran: Tehran - Service
Centre of Iran, No 510, South Karger Ave, Below Pasteur Sq. Tehran. Tel.: +98-21-6490608/0656/6407672. Kish Island: Cayhan
Electric Co., No. 69, Paradise Shopping Centre, Kish Island. Tel.: +98-76444-22894. Jordan: Bashiti Hardware, P.O.Box 1564, TLA
Ali, Amman. Tel.: +962-6-5350009/4770741, Fax: +962-6-5350012/4789783. Kenya: Zylog Enterprises, IPS Building, Kuanda Street,
P.O.Box 40877, Nairobi. Tel.: +254-2-338188/199, Fax: +254-2-330642. Kuwait: Al Omar Technical Co., P.O.Box 4062, 13041 Safat,
Kuwait. Tel.: +965-4848595/0039, Fax: +965-4845652. Lebanon: Est. F.A. Kettaneh SA, P.O.Box 110242, Dora Highway, Kettaneh
Building, Beirut. Tel.: +961-1-255860/6, Fax: +961-1-255891. Libya: El Ghoul Brothers, P.O.Box 348, Islamic Call Bldg., Office 201202, Benghazi. Tel.: +218-61-9097681/4183, Fax: +218-61-9094123. Madagascar: Group Tana Confort S. A. R. L., B. P. 1770,
Antananarivo. Tel.: +261-20-2264505, Fax: +261-20-2264244. Malta: John G. Cassar Ltd., 36 Victory Str, Qormi QRM 06, Malta.
Tel.: +356-21-493251, Fax: +356-21-483231. Mauritius: Happy World Marketing Ltd., Block 2, Industrial Estate, Coromandel,
P.O.Box 429, Port Louis. Tel.: +230-2076700, Fax: +230-2337330/7400. Nepal: Universal Trading Centre, P.O.Box 1947,
Tripureswor, Kathmandu. Tel.: +977-1-262192/260587/785, Fax: 261154. Nigeria: Amin Bros. Eng. Co. Ltd., 30A (Plot 1291), Akin
Adesola Street, Victoria Island, Lagos. Tel.: +234-1-3201778, Fax: +234-1-2613667. Oman: Oman Mktg. & Service Co., P.O.Box
2734, Ruwi, Muscat. Tel.: +968-560232, Fax: +968-560255. Pakistan: Karachi - Ammar Service & Spares, 60, Bank Arcade, Serai
Road, Karachi. Tel.: +92-21-2426905, Fax: 2427214/5243. Pakistan: Lahore - Electronics Inn, 212-G Raja Centre, Main Market,
Gulberg, Lahore. Tel.: +92-42-5756750. Philippines: Modern House International Enterprises, 213 Rizal Ave. Extension, between 2nd
and 3rd Ave. Kalookan City. Tel.: +632 366-4487, Fax: +632 366-4489. Qatar: Al Muftah Trading & Cont., P.O.Box 875, Doha. Tel.:
+974-4650880/4446868, Fax: +974-4441415. Saudi Arabia: Dammam - Ebrahim Fawaz Al Zayani, P.O.Box 76026, Al Raka,
Dammam. Tel.: +966-3-8140914, Fax: +966-3-8140824. Jeddah: Anasia Trading Co. Ltd. Caravan Shopping Centre, Hail Street. P.
O. Box 50959, Jeddah-21477, Tel. 02 650 0948/02 636 3825, Fax 02 638 0720. Madina: Garziz Trdg. for Bldg. Mat.&Decor.,
P.O.Box 3364, Madina. Tel.: +966-4-8261490/8227636, Fax: +966-4-8265741. Riyadh: Anasia Trading Co Ltd. New Akaria Building,
60th St., 3rd Floor, Building # 4, Office # 3402, Malaz. P. O. Box. 18689, Riyadh-11425, Tel.: 01 478 2549, Fax: 01 478 2761. Yanbu:
Bin Afif, P.O.Box 530 Yanbu, Al Bahr. Tel.: +966-4-3222626/8867, Fax: +966-4-3222210. Sri Lanka: Delmege Gen. Equip. Pvt. Ltd.,
No. 428/1AT. B., Jaya Mawatha (Darley Road), Colombo-10. Tel.: +94-11-2665914, Fax: +94-11-2665915. Sudan: United
Distribution Company, P.O.Box 325, Sayed Abdul Rehman Street, Khartoum. Tel.: +249-11-772612/777296, Fax: +249-11-770919.
Tanzania: General Motors Investment, P. O Box 16541, 14 Vingunguti Nyerere Road, Dar Es Salaam. Tel.: +255-22-2862661/5022,
Fax: +255-22-2862667/5412/3. Tunisia: STE Tunisienne De Quincaillerie Stq., Nvelle Z.I 2013, Ben Arous, Tunis, Tunisia, Tel: +216
71386102, Fax: +216 71380412. UAE: Abu Dhabi - Light House Electric., P.O.Box 120, Abu Dhabi. Tel.: +971-2-6726131, Fax:
+971-2-6720667. Dubai - Black & Decker (O) A.G., P.O.Box 5420, Dubai. Tel.: +971-4-7028234/233, Fax: +971-4-2822765. Ideal
Mach. & Equipt. R. W/shop P.O.Box 37116, Al Quoz, Dubai. Tel.: +971-4-3474160, Fax: +971-4-3474157. Sharjah - McCoy Middle
East LLC, P.O.Box 20228, Sharjah. Tel.: +971-6-5336321, Fax: +971-6-5336320. Uganda: The Building Centre, Kitgum House, 52
Station Road, P.O.Box 7436, Kampala. Tel.: +256-41-234567, Fax: +256-41-236413. Yemen: Aden - Middle East Trad. Co. Ltd.,
Mulla Dakka, Aden. Tel.: +967-2-240950, Fax: +967-2-240952. Sana'a: Middle East Trad. Co. Ltd., P.O.Box 12363, Hayel Street,
Sana'a. Tel.: +967-1-204201, Fax: +967-1-204204. Taiz: Middle East Trad. Co. Ltd., Campa area near Al-Kair mosque, Taiz. Tel.:
+967-4-231610/232033, Fax: +967-4-219869. Zimbabwe: J.D.Distributors, P.O.Box 226, 17 Bessemer Road, Graniteside, Harare.
Tel.: +263-4-753913-7, Fax: 753918. Cyprus: G. Kyprianou Trading Co Ltd., 51 Prodromou AVE. Strovolos, 1681, P.O. Box 23318
Nicosia Cyprus. Tel.: 00357 22 468170/1, Fax: 00357 22 468186, Email gktltd@spidernet.com.cy
POSTCODE …ó``jÈdG õ`eôdG
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF