D26411 | DeWalt D26411 HEATGUN instruction manual

D26411
D26414
Final Page size: A5 (148mm x 210mm)
English (original instructions)3
Copyright DeWALT
B
Fig. A
5
7
2
4
1
D26411
3
6
4
5
7
2
4
8
1
3
D26414
6
1
Fig. B
Fig. C
Fig. D
1
2
English
HEAT GUN
D26411, D26414
Congratulations!
Definitions: Safety Guidelines
You have chosen a DeWALT tool. Years of experience, thorough
product development and innovation make DeWALT one of the
most reliable partners for professional power tool users.
The definitions below describe the level of severity for each
signal word. Please read the manual and pay attention to
these symbols.
DANGER: Indicates an imminently hazardous
situation which, if not avoided, will result in death or
serious injury.
WARNING: Indicates a potentially hazardous situation
which, if not avoided, could result in death or
serious injury.
CAUTION: Indicates a potentially hazardous situation
which, if not avoided, may result in minor or
moderate injury.
NOTICE: Indicates a practice not related to
personal injury which, if not avoided, may result in
property damage.
Technical Data
Voltage
UK & Ireland
Type
Power input
Power input (115V)
Air temperature range (at nozzle)
VAC
VAC
Weight
kg
W
W
ºC
D26411
D26414
220-240
220-240
230/115
230/115
1
1
1800
2000
1600
1600
50–400 and 50 –400 and
50–600
50–600
0.65
0.71
EC-Declaration of Conformity
Machinery Directive
Denotes risk of electric shock.
Denotes risk of fire.
General Power Tool Safety Warnings
Heat Gun
D26411, D26414
DeWALT declares that these products described under
Technical Data are in compliance with:
2006/42/EC, EN60335-1:2012+A11:2014, EN60335-2-45:2002
+A1:2008 +A2:2012.
These products also comply with Directive 2014/30/EU and
2011/65/EU. For more information, please contact DeWALT at
the following address or refer to the back of the manual.
The undersigned is responsible for compilation of the technical
file and makes this declaration on behalf of DeWALT.
Markus Rompel
Director Engineering
DeWALT, Richard-Klinger-Straße 11,
D-65510, Idstein, Germany
20.03.2018
WARNING: To reduce the risk of injury, read the
instruction manual.
WARNING: Read all safety warnings, instructions,
illustrations and specifications provided with this
power tool. Failure to follow all instructions listed below
may result in electric shock, fire and/or serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
The term “power tool” in the warnings refers to your mainsoperated (corded) power tool or battery-operated (cordless)
power tool.
1) Work area safety
a ) Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b ) Do not operate power tools in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks which
may ignite the dust or fumes.
c ) Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose control.
2) Electrical safety
a ) Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk of
electric shock.
b ) Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if
your body is earthed or grounded.
3
English
c ) Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d ) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of
electric shock.
e ) When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
f ) If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
3) Personal safety
a ) Stay alert, watch what you are doing and use
common sense when operating a power tool. Do not
use a power tool while you are tired or under the
influence of drugs, alcohol or medication. A moment
of inattention while operating power tools may result in
serious personal injury.
b ) Use personal protective equipment. Always wear
eye protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection used
for appropriate conditions will reduce personal injuries.
c ) Prevent unintentional starting. Ensure the switch
is in the off position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your finger on the
switch or energising power tools that have the switch on
invites accidents.
d ) Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached
to a rotating part of the power tool may result in
personal injury.
e ) Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power tool
in unexpected situations.
f ) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g ) If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection
can reduce dust-related hazards.
4) Power tool use and care
a ) Do not force the power tool. Use the correct power
tool for your application. The correct power tool
will do the job better and safer at the rate for which it
was designed.
b ) Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
4
c ) Disconnect the plug from the power source and/or
the battery pack from the power tool before making
any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce the
risk of starting the power tool accidentally.
d ) Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users.
e ) Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f ) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g ) Use the power tool, accessories and tool bits etc.,
in accordance with these instructions taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
5) Service
a ) Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Safety Instructions for Heat Guns
A fire may result if the appliance is not used with care, therefore:
• Heat may be conducted to combustible materials that
are out of sight. DO NOT use in a damp atmosphere,
where flammable gases may be present or near
combustible materials.
• DO NOT apply to the same place for a long time.
• DO NOT use in presence of an explosive atmosphere.
• Place the appliance on its stand after use and allow it to cool
down before storage.
• DO NOT leave the tool unattended while it is switched on.
• DO NOT place your hand over the air vents or block the vents
in any way.
• The nozzle and accessories of this tool become extremely hot
during use. Let these parts cool down before touching.
• ALWAYS switch the tool off before putting it down.
• This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have
been given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
• Ensure adequate ventilation as toxic fumes may be produced.
• DO NOT use as a hair dryer.
• DO NOT obstruct either the air intake or nozzle outlet, as this
may cause excessive heat build up resulting in damage to
the tool.
• DO NOT direct the hot air blast at other people.
English
•
•
•
•
•
DO NOT touch the metal nozzle as it becomes very hot during
use and remains hot for up to 30 minutes after use.
DO NOT place the nozzle against anything while using or
immediately after use.
DO NOT poke anything down the nozzle as it could give you
an electric shock. Do not look down the nozzle while the unit is
working because of the high temperatures being produced.
DO NOT allow paint to adhere to the nozzle or scraper as it
could ignite after some time.
DO NOT remove the heat barrel cover during use.
Additional Safety Warnings for Heat Guns
To reduce the risk of explosion, DO NOT use in paint spray
booths or within 3.0 m of paint spraying operations.
• DO NOT use this tool to remove paint containing lead.
The peelings, residue and vapors of paint may contain lead
which is poisonous.
• Hidden areas such as behind walls, ceilings, floors, soffit
boards and other panels may contain flammable materials
that could be ignited by the heat gun when working in these
locations. The ignition of these materials may not be readily
apparent and could result in property damage and injury to
persons. When working in these locations, keep the heat gun
moving in a back-and-forth motion. Lingering or pausing in
one spot could ignite the panel or the material behind it.
NOTE: These heat guns are capable of producing
temperatures in excess of 550 °C.
• DO NOT use this tool to heat food.
• DO NOT lay the heat gun on flammable surfaces when
operating the gun or immediately after shutting it off.
• Keep moveable items secured and steady while scraping.
• Be sure to direct the hot air blast in a safe direction; away from
other people or flammable objects.
• KEEP FINGERS AWAY FROM METAL NOZZLE; it becomes
very hot during use and remains hot for 30 minutes after use.
Wear gloves to protect hands.
• ALWAYS keep nozzle away from cord.
• Splinters and small particles of stripped paint can be
ignited and blown through holes and cracks in the surface
being stripped.
• DO NOT burn the paint. Use the scraper provided and keep
the nozzle at least 25 mm away from the painted surface.
When working in a vertical direction, work downwards to
prevent paint from falling into the tool and burning.
• ALWAYS use good quality scrapers and stripping knives.
• DO NOT use the heat gun in combination with
chemical strippers.
• DO NOT use accessory nozzles as scrapers.
• DO NOT direct heatgun airflow directly on glass. The
glass may crack and could result in property damage or
personal injury.
• Maintain labels and nameplates. These carry
important information.
• Place the heat gun on a stable, level surface when not hand
held. Place the cord in a position that won't cause the heat
gun to tip over.
•
•
•
•
Be constantly aware that this tool can ignite flammable
materials, soften or melt others. Regardless of the task you
are performing, shield or keep the heat gun away from
these materials.
You may occasionally notice some slight smoking of the tool
after it is turned off. This is the result of heating the residual
oil that was deposited on the heating element during the
manufacturing process.
Use eye protection and other safety equipment.
Removing Paint
WARNING: Extreme care should be taken when
stripping paint.
Before beginning any paint removal process you should determine
whether the paint you are removing contains lead. LEAD-BASED
PAINT SHOULD ONLY BE REMOVED BY A PROFESSIONAL
AND SHOULD NOT BE REMOVED USING A HEAT GUN.
Persons removing paint should follow these guidelines:
1. Move the workpiece outdoors. If this is not possible, keep the
work area well ventilated. Open the windows and put an
exhaust fan in one of them. Be sure the fan is moving the air
from inside to outside.
2. Remove or cover any carpets, rugs, furniture, clothing, cooking
utensils and air ducts.
3. Place drop cloths in the work area to catch any paint chips or
peelings. Wear protective clothing such as extra work shirts,
overalls and hats.
4. Work in one room at a time. Furnishings should be removed
or placed in the center of the room and covered. Work areas
should be sealed off from the rest of the dwelling by sealing
doorways with drop cloths.
5. Children, pregnant or potentially pregnant women and nursing
mothers should not be present in the work area until the work is
done and all clean up is complete.
6. Wear a dust respirator mask or a dual filter (dust and fume)
respirator mask. Be sure the mask fits. Beards and facial hair
may keep masks from sealing properly. Change filters often.
DISPOSABLE PAPER MASKS ARE NOT ADEQUATE.
7. Use caution when operating the heat gun. Keep the heat gun
moving as excessive heat will generate fumes which can be
inhaled by the operator.
8. Keep food and drink out of the work area. Wash hands, arms
and face and rinse mouth before eating or drinking. Do not
smoke or chew gum or tobacco in the work area.
9. Clean up all removed paint and dust by wet mopping the floors.
Use a wet cloth to clean all walls, sills and any other surface
where paint or dust is clinging. DO NOT SWEEP, DRY DUST
OR VACUUM. Use a high phosphate detergent or trisodium
phosphate (TSP) to wash and mop areas.
10. At the end of each work session put the paint chips and debris
in a double plastic bag, close it with tape or twist ties and
dispose of properly.
11. Remove protective clothing and work shoes in the work area
to avoid carrying dust into the rest of the dwelling. Wash work
clothes separately. Wipe shoes off with a wet rag that is then
washed with the work clothes. Wash hair and body thoroughly
with soap and water.
5
English
IMPORTANT NOTICE
In order for this tool to be an effective paint stripper, it must
produce extremely high temperatures. As a consequence, the
stripper is capable of igniting paper, wood, paint and varnish
residue and similar materials.
As you become more familiar with the tool and develop the
proper technique, the danger of accidental ignition will be greatly
reduced. In establishing the proper technique, the best thing to
do is PRACTICE! Work on simple stripping projects, preferably
outdoors, until you get a “feel” for how to use your stripper safely
and effectively.
As you Practice, Observe the Following
Procedures for Safety
•
•
•
•
•
•
•
Always be sure the tool is turned off and disconnected from
power supply when unattended.
Clean the scraper blade often during use. Built up residue on
the blade is highly flammable.
Experiment to find the optimum distance from the
tool’s nozzle to the surface being stripped. This distance
25.4 mm–50.8 mm will vary depending on the material
being removed.
Keep the heat gun moving ahead of the scraper blade at
all times.
As you work, clean up loose pieces of paint as they accumulate
around the work area.
When working indoors, keep away from curtains, papers,
upholstery and similar flammable materials.
Above all, remember that this is a serious tool that is capable
of producing excellent results when used properly. Practice on
simple projects until you feel comfortable with your stripper.
Only then will you have mastered the proper technique.
WARNING: We recommend the use of a residual current
device with a residual current rating of 30mA or less.
Residual Risks
In spite of the application of the relevant safety regulations
and the implementation of safety devices, certain residual risks
cannot be avoided. These are:
• Impairment of hearing.
• Risk of personal injury due to flying particles.
• Risk of burns due to accessories becoming hot
during operation.
• Risk of personal injury due to prolonged use.
Electrical Safety
The electric motor has been designed for one voltage only.
Always check that the power supply corresponds to the voltage
on the rating plate.
Your DeWALT tool is double insulated in accordance
with EN60745; therefore no earth wire is required.
WARNING: 115 V units have to be operated via a fail-safe
isolating transformer with an earth screen between the
primary and secondary winding.
6
WARNING: If the plug or power cord is damaged, it must
be replaced by the manufacturer or its representative or by
a DeWALT authorised service centre.
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
• Safely dispose of the old plug.
• Connect the brown lead to the live terminal in the plug.
• Connect the blue lead to the neutral terminal.
WARNING: No connection is to be made to the
earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 13 A.
Using an Extension Cable
If an extension cable is required, use an approved 3–core
extension cable suitable for the power input of this tool (see
Technical Data).The minimum conductor size is 1.5 mm2; the
maximum length is 30 m.
When using a cable reel, always unwind the cable completely.
Package Contents
The package contains:
1 Heat gun
1 Set of accessories
1 Instruction manual
• Check for damage to the tool, parts or accessories which may
have occurred during transport.
• Take the time to thoroughly read and understand this manual
prior to operation.
Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual before use.
Wear ear protection.
Wear eye protection.
Date Code Position (Fig. A)
The date code 8 , which also includes the year of manufacture,
is printed into the housing.
Example:
2018 XX XX
Year of Manufacture
Description (Fig. A)
WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
1 On/off switch
2 Air vents
3 Kick-off stand
English
4 Air temperature adjustment knob (D26411)
LCD air temperature indicator and adjuster (D26414)
5 Nozzle
6 Tool hanging ring
7 Heat barrel cover
Applications
The table below suggests settings for different applications.
Setting
Applications
Low
•
•
•
•
•
•
Medium
• Welding plastics
• Bending plastic pipes and sheets
• Loosening rusted or tightly fastened nuts and bolts
High
• Removing paint and lacquer
• Soldering plumbing joints
• Removing linoleum or vinyl floor tiles
Intended Use
Your heat gun has been designed for stripping paint, soldering
pipes, shrinking PVC, welding and bending plastics as well as
general drying and thawing purposes.
DO NOT use under wet conditions or in the presence of
flammable liquids or gases.
The heat gun is a professional power tool. DO NOT let children
come into contact with the tool. Supervision is required when
inexperienced operators use this tool.
• Young children and the infirm. This appliance is not
intended for use by young children or infirm persons
without supervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
Drying paint and varnish
Removing stickers
Waxing and dewaxing
Drying wet timber prior to filling
Shrinking PVC wrapping and insulation tubes
Thawing frozen pipes
To Attach the Correct Accessory
This tool is supplied with a set of accessories for
different applications.
Icon
Description
Shrink sleeving (heat over
concentrated small area)
50 mm Fish tail
surface nozzle
Drying, removing paint,
removing vinyl or linoleum,
thawing (heat spread over
wide area)
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
Air Temperature (Fig. A)
D26411
The air temperature can be adjusted to suit a wide range of
applications. Turn the air temperature adjustment knob 4 clockwise or counterclockwise for higher or lower heat.
D26414
• Press and release the LCD air temperature indicator
and adjuster 4 to set the desired temperature in
10 °C increments.
• To continously increase or decrease the temperature press
and hold the LCD air temperature indicator and adjuster 4 .
• Release the indicator when desired temperature or
minimum/maximum temperature is reached.
• The display shows the actual rising/falling temperature until
the desired temperature is reached.
Set and Forget Temperature Control System
D26414
The desired temperature is stored in the memory of the tool.
Each time the heat gun is turned on, the heat gun heats to
the last temperature setting, with respect to air flow. If unsure
about the setting, always start with a low temperature setting
and gradually increase the temperature until the desired setting
is reached.
Purpose
Cone nozzle
1. Make sure the on/off switch 1 is in position O and the tool
is disconnected from the power source. Ensure the nozzle
has cooled down.
2. Place the desired accessory onto the nozzle.
OPERATION
Instructions for Use
WARNING: Always observe the safety instructions and
applicable regulations.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
WARNING: Make sure the nozzle always points away
from you and any bystanders.
WARNING: DO NOT drop anything into the nozzle.
Proper Hand Position (Fig. B, C)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
7
English
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
WARNING: Do not place your other hand over the air
vents (Fig. C).
Proper hand position requires one hand holding the tool as
shown in Figure B.
Prior to Operation
1. Attach the correct accessory recommended for
the application.
2. Turn the air temperature adjustment knob/LCD air
temperature indicator and adjuster 4 to desired
air temperature.
Switching On and Off (Fig. D)
1. Push the on/off switch 1 to the desired air flow settings:
I: 240 liter/min (50 °C–400 °C)
250 liter/min (50 °C–400 °C) (D26414)
A low air flow to heat up the workpiece slowly.
II: 450 liter/min (50 °C–600 °C)
500 liter/min (50 °C–600 °C) (D26414)
A high air flow to heat up the workpiece quickly.
2. To turn the tool off, push the on/off switch 1 to position O.
Disconnect the tool from the power source and let the tool
cool down before moving or storing it.
Removing Paint
WARNING: Refer to Important Notice under Additional
Safety Instructions for Heat Guns before using the
tool to remove paint.
WARNING: Do not strip metal window frames as the heat
may crack the glass.
• When striping other window frames, use a glass
protection nozzle.
• To prevent igniting the surface, do not keep the tool
directed at one spot too long.
• Avoid collecting paint on the scraper accessory, as it
may ignite. If necessary, carefully remove paint debris
from the scraper accessory using a knife.
1. Attach the appropriate accessory.
2. Turn the air temperature adjustment knob/LCD air
temperature indicator and adjuster 4 to high.
3. Turn the tool on by selecting the desired air flow.
4. Direct the hot air onto the paint to be removed.
Best results will be achieved if the heat gun is moved slowly,
but CONSTANTLY, from side to side to evenly distribute
heat. DO NOT LINGER OR PAUSE IN ONE SPOT.
5. When the paint softens, scrape the paint away using a
hand scraper.
REMEMBER: Splinters and small particles of stripped paint can
be ignited and blown through holes and cracks in the surface
being stripped.
8
Stationary Use (Fig. A)
This tool can also be used in stationary mode.
1. Fold down the kickstand 3 as shown in Figure A.
2. Set the tool onto a level, stable workbench. Ensure the tool
will not tip over.
3. Secure the power cord to prevent entanglement or pulling
the tool off the workbench.
4. Turn the tool on by selecting the desired air flow.
Constant Heat Control (Overload Protection)
When the tool is overloaded, this feature protects the heating
element from damage without stopping the tool and/or
without a cool down period.
1. When the temperature gets too hot, the heating element
switches itself off. The motor will continue to run and
produce cold air.
2. When the temperature has cooled sufficiently (taking
only a few seconds) the heating element will switch
on automatically.
Tool Ring (Fig. A)
WARNING: ALWAYS turn heat gun off, disconnect from
the power source and let the tool cool down for at least 30
minutes before moving or storing it.
For easy storage, the tool can hang from the tool ring 6 . The
heat gun should be stored indoors.
Cool Down Period
The nozzle and accessory becomes very hot during use. Turn
heat gun off, disconnect from the power source and let the tool
cool down for at least 30 minutes before moving or storing it.
NOTE: To reduce the cooling time, switch the tool on at the
lowest air temperature setting and let it run for a few minutes
before turning the heat gun off.
MAINTENANCE
Your DeWALT power tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
Lubrication
Your power tool requires no additional lubrication.
English
Cleaning
WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.
WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
Optional Accessories
WARNING: Since accessories, other than those offered
by DeWALT, have not been tested with this product, use
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only DeWALT recommended
accessories should be used with this product.
Consult your dealer for further information on the
appropriate accessories.
Protecting the Environment
Separate collection. Products and batteries marked
with this symbol must not be disposed of with normal
household waste.
Products and batteries contain materials that can
be recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and batteries
according to local provisions. Further information is available at
www.2helpU.com.
9
Belgique et
Luxembourg België en Luxemburg
DeWALT - Belgium BVBA
Egide Walschaertsstraat 16
2800 Mechelen
Tel: NL 32 15 47 37 63
Tel: FR 32 15 47 37 64
Fax:
32 15 47 37 99
www.dewalt.be
enduser.BE@SBDinc.com
Danmark
DeWALT (Stanley Black&Decker AS)
Roskildevej 22
2620 Albertslund
Tel:
Fax:
www.dewalt.dk
kundeservice.dk@sbdinc.com
Deutschland
DeWALT
Richard Klinger Str. 11
65510 Idstein
Tel:06126-21-0
Fax:06126-21-2770
www.dewalt.de
infodwge@sbdinc.com
Ελλάς
DeWALT (Ελλάς) Α.Ε.
EΔΡΑ-ΓΡΑΦΕΙΑ : Στράβωνος 7
& Λ. Βουλιαγμένης, Γλυφάδα 166 74, Αθήνα
SERVICE : Ημερος Τόπος 2 (Χάνι Αδάμ) – 193 00 Ασπρόπυργος
Τηλ:00302108981616
Φαξ:00302108983570
www.dewalt.gr
Greece.Service@sbdinc.com
España
DeWALT Ibérica, S.C.A.
Parc de Negocios “Mas Blau”
Edificio Muntadas, c/Bergadá, 1, Of. A6
08820 El Prat de Llobregat (Barcelona)
Tel:
Fax:
934 797 400
934 797 419
www.dewalt.es
respuesta.postventa@sbdinc.com
France
DeWALT
5, allée des Hêtres
BP 60105, 69579 Limonest Cedex
Tel:
Fax:
04 72 20 39 20
04 72 20 39 00
www.dewalt.fr
scufr@sbdinc.com
Schweiz
Suisse
Svizzera
DeWALT
In der Luberzen 42
8902 Urdorf
Tel:
Fax:
044 - 755 60 70
044 - 730 70 67
www.dewalt.ch
service@rofoag.ch
Ireland
DeWALT
Building 4500, Kinsale Road
Cork Airport Business Park
Cork, Ireland
Tel:00353-2781800
Fax:
01278 1811
www.dewalt.ie
Sales.ireland@sbdinc.com
Italia
DeWALT
via Energypark 6
20871 Vimercate (MB), IT
Tel: Fax: 800-014353
39 039-9590200
39 039-9590311
www.dewalt.it
Nederlands
DeWALT
Netherlands BVPostbus 83,
6120 AB BORN
Tel:
Fax:
31 164 283 063
31 164 283 200
www.dewalt.nl
Norge
DeWALT
Postboks 4613
0405 Oslo, Norge
Tel: Fax: 45 25 13 00
45 25 08 00
www.dewalt.no
kundeservice.no@sbdinc.com
Österreich
DeWALT
Werkzeug Vertriebsges m.b.H
Oberlaaerstrasse 248, A-1230 Wien
Tel: Fax: 01 - 66116 - 0
01 - 66116 - 614
www.dewalt.at
service.austria@sbdinc.com
Portugal
DeWALT
Ed. D Dinis, Quina da Fonte
Rua dos Malhoes 2 2A 2º Esq.
Oeiras e S. Juliao da Barra, paço de Arcos e Caxias
2770 071 Paço de Arcos
Tel: Fax: +351 214667500
+351214667580
www.dewalt.pt
resposta.posvenda@sbdinc.com
Suomi
DeWALT
PL47
00521 Helsinki, Suomi
Puh: Faksi:
010 400 4333
0800 411 340
www.dewalt.fi
asiakaspalvelu.fi@sbdinc.com
Sverige
DeWALT
BOX 94
43122 Mölndal
Sverige
Tel:
Fax: 031 68 61 60
031 68 60 08
www.dewalt.se
kundservice.se@sbdinc.com
Türkiye
Sanayi ve Ticareet Bakanlığı tebliğince kullanim ömrü 7 yıldır.
Stanley Black & Decker Turkey Alet Üretim San. Tic. Ltd.Şti.
Kozyataği Mh Değirmen Sk.
Nida Kule No: 18 Kat: 6, 34742
Kadıköy, İstanbul, Türkiye
Tel: Faks:
+90 216 665 2900
+90 216 665 2901
www.dewalt.com.tr
info-tr@sbdinc.com
United
Kingdom
DeWALT, 210 Bath Road;
Slough, Berks SL1 3YD
Tel: Fax: 01753-567055
01753-572112
www.dewalt.co.uk
emeaservice@sbdinc.com
Australia
DeWALT
810 Whitehorse Road Box Hill
VIC 3103 Australia
Tel: Aust 1800 338 002
Tel: NZ 0800 339 258
www.dewalt.com.au
www.dewalt.co.nz
Middle East Africa
DeWALT
P.O. Box - 17164,
Jebel Ali Free Zone (South), Dubai, UAE
Tel: Fax: www.dewalt.ae
Service.MEA@sbdinc.com
N607929
10
70 20 15 10
70 22 49 10
971 4 812 7400
971 4 2822765
5/18
Download PDF