MULTILINE | Stanley MULTILINE MULTILINE LASER instruction manual

GB
D
F
5 - Beam Self-Leveling Multi-Line Laser
MultiLine
I
E
PT
NL
DK
SE
FIN
NO
PL
GR
CZ
RU
HU
SK
SI
BG
RO
EE
77-122
Please read these instructions before operating the product
LV
Self-Leveling
LT
Contents
1.
2.
3.
4.
5.
6.
7.
DO NOT remove any warning label(s) on the housing. This instrument must only be used for
leveling and layout tasks as outlined in this manual.
ALWAYS make sure that any bystanders in the vicinity of use are made aware of the
dangers of looking directly into the laser tool.
Safety
Product Description
Specifications
Operating Instructions
Calibration
Maintenance and Care
Warranty
DO NOT use in combination with other optical instruments. Do not modify the instrument, or
make manipulations or use in other applications than those described in the manual.
DO NOT look into the beam with optical aids, such as magnifiers, binoculars or Telescopes.
DO NOT stare into the laser beam or direct it towards other persons. Make sure the
instrument is not set at eye level. Eye protection is normally afforded by natural aversion
responses such as the blink reflex.
DO NOT direct the laser beam at other persons.
Safety
ALWAYS turn the laser tool “OFF” when not in use. Leaving the laser tool “ON” increases
the risk of someone inadvertently staring into the laser beam.
User Safety
Carefully read the Safety Instructions and User Manual before using this product. The person
responsible for the instrument must ensure that all users understand and adhere to these
instructions.
Retain this manual for future reference.
IMPORTANT: The following labels are on your laser tool for your convenience and safety.
They indicate where the laser light is emitted by the level. ALWAYS BE AWARE of their
location when using the level.
DO NOT operate the laser tool in combustible areas such as in the presence of flammable
liquids, gases or dust.
DO NOT disassemble the laser tool. There are no user serviceable parts inside.
Disassembling the laser will void all warranties on the product. Do not modify the product in
any way. Modifying the laser tool may result in hazardous laser radiation exposure.
DO NOT use this instrument in areas where a risk of explosion is present.
NOTE: Since the laser beam is of the focused type, ensure you check the beam’s path over
a relatively long distance and take all necessary precautions to ensure the beam cannot
interfere with other persons.
L A S E R R A D I AT I O N - D O N O T
S TA R E I N T O B E A M O R V I E W
D I R E C T LY W I T H
OPTICAL INSTRUMENTS
CLASS 1M LASER PRODUCT
EN 60825-1
2
MAX OUTPUT ≤ 1 mW @ 630 - 670 nm
77-122
77-122
3
Battery Safety
Declaration of Conformity
WARNING: Batteries can explode or leak and can cause injury or fire. To reduce this risk:
ALWAYS follow all instructions and warnings on the battery label and package.
The Stanley Works declares that the CE Mark has been applied to
this product in accordance with the CE Marking Directive 93/68/
EEC.
DO NOT short any battery terminals
This product conforms with EN60825-1:2007.
DO NOT charge alkaline batteries.
For further details please refer to www.stanleyworks.com.
EN 60825-1
ROHS Compliant
DO NOT mix old and new batteries. Replace all of them at the same time with new batteries
of the same brand and type.
DO NOT mix battery chemistries.
Product Description
DO NOT dispose of batteries in fire.
ALWAYS keep batteries out of reach of children.
Package Contents
ALWAYS remove batteries if the device will not be used for several months.
1.
2.
3.
4.
5.
6.
7.
8.
NOTE: Ensure that the correct batteries as recommended are used.
NOTE: Ensure the batteries are inserted in the correct manner, with the correct polarity.
End of Life
DO NOT dispose of this product with household waste.
Laser Unit
IR Remote Controller
Laser Target
Laser Detector with Detector Clamp
Glasses
Carrying Case
Batteries (Laser Unit - 4 x AA, IR Remote Controller - 2 x AA, Laser Detector - 1 x 9V)
User Manual
ALWAYS dispose of batteries per local code.
PLEASE RECYCLE in line with local provisions for the collection and disposal of electrical
and electronic waste under the WEEE Directive.
4
77-122
77-122
5
Product Overview
Specifications
Laser Unit
1.
2.
3.
4.
5.
6.
7.
8.
4
1
5
6
2
7
3
8
9
Keyboard
Main Power / Transport Lock
Fine Tuning Wheel
Window for 90° Vertical Reference Beam Laser
Window for Front Vertical Beam Laser
Window for Horizontal Beam Laser
IR Sensor
Bubble Level
9. Window for Rear Vertical Beam Laser
10. Laser Warning Label
Battery Compartment Cover
11. Handle
12. Window for 90° Vertical Reference Beam Laser
12
10
11
Laser Unit
Leveling Accuracy:
≤ 2 mm / 10 m
(≤ 5/64 in / 30 ft)
Down Beam Accuracy:
≤ 1.5 mm / 5 m
(≤ 1/16 in / 15 ft)
Square Beam Accuracy:
≤ 1 mm / 5 m
Horizontal / Vertical Accurracy
14
IR Remote Controller
Working Distance:
with Laser Detector:
≤ 15 m (≤ 50 ft)
≤ 50 m (≤ 165 ft)
2
4
1.
2.
3.
4.
635 nm ± 5 nm
Operating Time:
6h
Power Voltage:
6V
Power Supply:
4 x AA Batteries (Alkaline)
Operating Temperature Range:
IR LED
Keyboard
Location for Lanyard
Battery Compartment Cover
Storage Temperature Range:
Weight (without Base and Batteries):
3
6
Class 1M
IP Rating:
1
77-122
(≤ 1/16 in / 10 ft)
Self-Leveling to ± 3°
Laser Wavelength:
13. Adjustable Legs 3x
14. 5/8 - 11 Threaded Mount
Window for Down Beam Laser
≤ 1.5 mm / 3 m
Working Range:
Laser Class:
13
(≤ 1/32 in / 15 ft)
77-122
IP54
-10° C to +40° C
-20° C to +60° C
980 g
(+14° F to +104° F)
(-4° F to +140° F)
(34,5 oz)
7
Size:
110 mm × 105 mm × 180 mm
(4 5/16 in × 4 1/8 in × 7 1/16 in)
Laser Unit
IR Remote Controller
Battery Installation / Removal
Power Voltage:
3V
Power Supply:
2 x AA Batteries (Alkaline)
Weight (without Batteries):
Size:
Operating Instructions
37 g
35 mm × 25 mm × 120 mm
(1,3 oz)
1.
Turn laser unit to back. Open battery
compartment cover by pressing and sliding
out.
2.
Install / Remove batteries. Orient batteries
correctly when placing into laser unit.
(1 3/8 in × 1 in × 4 3/4 in)
-+
-+
++
3.
8
77-122
77-122
-
Close and lock battery compartment cover
by sliding in until securely closed.
9
Function
1.
8.
Low battery - Left LED blinks red to indicate
when battery power is low. Replace
batteries.
1.
Turn any of the adjustable legs as needed to
level the laser unit within its workable range.
Use the bubble vial for reference.
2.
Use fine adjustment wheel to gradually
rotate the projection of the laser beam(s).
3.
5/8 - 11 thread mount available for optional
accessories.
Transport lock in locked position. Laser
power is OFF.
Laser Unit Base
Locked
2.
Unlocked
3.
Laser Mode
4.
Pulse Mode
Transport lock in unlocked position. Laser
power is ON. Down laser beam and
horizontal laser beam turn on. Left LED
indicator lights green when laser power is
on.
Bubble Vial
3x
Press laser mode key to toggle through
available laser modes - horizontal only,
both horizontal and vertical, horizontal and
vertical with left and right 90° vertical
reference beam, horizontal with all 4 vertical.
Press pulse mode key to toggle between
pulse mode ON and OFF. Indicator LED lights
green when on. Pulse mode allows use with
a laser detector.
Standard Mount for
Optional Tripod Mounting
5/8 in
5.
10
Laser beam(s) blink to indicate the laser unit
is out of the working range. Reposition laser
unit to be more level.
77-122
77-122
11
IR Remote Controller
Applications
Battery Installation / Removal
1.
Turn laser unit to back. Open battery
compartment cover by pressing and sliding
out.
2.
Install / Remove batteries. Orient batteries
correctly when placing into laser unit.
3.
1.
Plumb:
Using the vertical laser beam, establish a
vertical reference plane. Position the desired
object(s) until they are aligned with the
vertical reference plane to ensure object(s)
are plumb.
Establish 2 reference points that need to be
plumb. Align either the down laser beam or
the up laser cross to a set reference point.
The opposing laser beam(s) will be projecting
a point which is plumb. Position the desired
object until the laser beam is aligned with
the second reference point that needs to be
plumb with the set reference point.
2.
Level:
Using the horizontal laser beam, establish
a horizontal reference plane. Position the
desired object(s) until they are aligned with
the horizontal reference plane to ensure
object(s) are level.
3.
Square:
Using either the vertical and horizontal
laser beams with or without the 90° vertical
reference laser beam, establish a point
where the vertical and horizontal beams
cross. Position the desired object(s) until
they are aligned with both the vertical and
horizontal laser beams to ensure object(s)
are square.
4.
Pulse Mode:
Setting laser unit to pulse mode allows use
of optional laser detectors.
+ + -
Close and lock battery compartment cover
by sliding in until securely closed.
Function
12
1.
Aim remote controller towards laser unit
and press laser mode key to toggle through
available laser modes.
2.
Press pulse mode key to toggle between
pulse mode ON and OFF.
Laser Mode
Pulse Mode
77-122
77-122
13
Calibration
5.
NOTE: The laser unit has been calibrated at the time of manufacturing. Periodically check
the accuracy of the laser unit to ensure that the calibrated specifications are maintained.
Level Beam Accuracy
D1
1.
Place laser unit as shown with laser ON.
Mark point P1 at cross.
6.
P1
D1
2
D1
2.
Rotate laser unit 180° and mark point P2
at cross.
P2
P1
D1
2
3.
Move laser unit close to wall and mark
point P3 at cross.
P1
P2
P3
Measure the vertical distance from
the floor to each point. Calculate the
difference between distances DP1 and DP3
to get D3 and distances DP2 and DP4 to get
D4 .
Calculate the maximum allowed offset
distance and compare to the difference
of D3 and D4 as shown in the equation. If
the sum is not less than or equal to the
calculated maximum offset distance the
unit must be returned to your Stanley
Distributor.
(DP1 - DP3 ) = D3
P4
P1
P3
P2
DP3
DP1
DP4
DP2
(DP2 - DP4 ) = D4
Maximum Offset Distance:
Max
= 0,2 mm
m x (D1 m - (2 x D2 m))
= 0,0024 in
ft x (D1 ft - (2 x D2 ft))
Compare:
D3 - D4 ≤ ± Max
Example: D1 = 10 m, D2 = 0,5 m
DP1 = 30,75 mm, DP2 = 29 mm, DP3 = 30 mm, DP4 = 29,75 mm
D3 = (30,75 mm - 30 mm) = 0,75 mm
D4 = (29 mm - 29,75 mm) = - 0,75 mm
0,2 mm
m x (10 m - (2 x 0,5 m) = 1,8 mm (maximum allowed offset distance)
(0,75 mm) - (- 0,75 mm) = 1,5 mm
1,5 mm ≤ 1,8 mm (TRUE, unit is within calibration)
Horizontal Beam Accuracy
D2
1.
4.
Rotate laser unit 180° and mark point P4
at cross.
P4
P1
P2
P3
Place laser unit as shown with horizontal,
vertical, and both 90° vertical reference
laser beams ON. Mark point P1 where the
horizontal and left 90° vertical reference
laser beams cross.
P1
D1
D2
14
77-122
77-122
15
Vertical Beam Accuracy
2.
Rotate laser unit 90° and align front
vertical laser beam with point P1 . Mark
point P2 where the horizontal and front
vertical laser beams cross.
P1
P2
1.
D1
3.
4.
5.
Rotate laser unit 90° and align right 90°
vertical reference laser beam with point
P1 . Mark point P3 where the horizontal and
right 90° vertical reference laser beams
cross.
D1
P2
P3
2 x D1
P4
D1
P1
P2
P3
2.
Move laser unit to opposite side of door
jamb or reference point and align vertical
beam with P1 and P2 .
D1
D1 P3
2 x D1
D2
3.
Measure the horizontal distances between
P1 and the vertical beam from the 2nd
location.
Vertical
Beam
P1
D2
Maximum Offset Distance:
Max
P1
P2
= 1 mm
m x D1 m
= 0,012 in
ft x D1 ft
4.
Compare:
D2 ≤ Max
Example: D1 = 5 m, D2 = 1 mm
1 mm
m x 5 m = 5 mm (maximum allowed offset distance)
1 mm ≤ 5 mm (TRUE, unit is within calibration)
16
D1
P1
P2
P3
Measure the vertical distance D2 between
the highest and lowest point.
Calculate the maximum allowed offset
distance and compare to D2 . If D2 is
not less than or equal to the calculated
maximum offset distance the unit must be
returned to your Stanley Distributor.
P1
Measure the height of a door jamb or
reference point to get distance D1 . Place
laser unit as shown with laser ON. Aim
vertical beam towards door jamb or
reference point. Mark points P1 , P2 , and
P3 as shown.
Calculate the maximum allowed offset
distance and compare to D2 . If D2 is
not less than or equal to the calculated
maximum offset distance the unit must be
returned to your Stanley Distributor.
Maximum Offset Distance:
Max
= 1 mm
m x D1 m
= 0,012 in
ft x D1 ft
Compare:
D2 ≤ Max
Example: D1 = 2 m, D2 = 1 mm
1 mm
m x 2 m = 2 mm (maximum allowed offset distance)
1 mm ≤ 2 mm (TRUE, unit is within calibration)
77-122
77-122
17
Maintenance and Care
90° Vertical Beam Accuracy
You will need at least 1.5 m2 (16 ft2) of floor space and possibly an assistant for this check.
Laser unit is not waterproof. DO NOT allow to get wet. Damage to internal circuits may
result.
1.
Place the laser unit on a level floor, and
turn on all beams.
DO NOT leave laser unit in direct sunlight or expose it to high temperatures. The housing
and some internal parts are made of plastic and may become deformed at high temperatures.
DO NOT store the laser unit in a cold environment. Moisture may form on interior parts
when warming up. This moisture could fog up laser windows and cause corrosion of internal
circuit boards.
P1
2.
When working in dusty locations, some dirt may collect on the laser window. Remove any
moisture or dirt with a soft, dry cloth.
Measure exactly 0,91 m (3 ft) out from
the center of the laser unit along the front
vertical laser beam. Mark this point P1 .
0,91 m (3 ft)
DO NOT use aggressive cleaning agents or solvents.
Store the laser unit in its case when not in use. If storing for extended time, remove batteries
before storage to prevent possible damage to the instrument.
P1
3.
Measure exactly 1,22 m (4 ft) out the
center of the instrument along either of
the 90° vertical reference beams, and
mark this point P2 .
1,22 m (4 ft)
P2
P1
4.
5.
18
Measure from point A to point B; this
distance D1 should equal 1,52 m ± 1.2 mm
(5 ft ± 3/64 in). If not, the unit must be
returned to your Stanley Distributor.
Repeat steps 1 through 4 to check the
other beams.
D1
P2
77-122
77-122
19
Warranty
One Year Warranty
Stanley Tools warrants its electronic measuring tools against deficiencies in materials and/or
workmanship for one year from date of purchase.
Deficient products will be repaired or replaced, at Stanley Tools’ option, if sent together with
proof of purchase to:
Stanley UK Sales Limited
Gowerton Road
Brackmills, Northampton NN4 7BW
This Warranty does not cover deficiencies caused by accidental damage, wear and tear, use
other than in accordance with the manufacturer’s instructions or repair or alteration of this
product not authorised by Stanley Tools.
Repair or replacement under this Warranty does not affect the expiry date of the Warranty.
To the extent permitted by law, Stanley Tools shall not be liable under this Warranty for
indirect or consequential loss resulting from deficiencies in this product.
This Warranty may not be varied without the authorisation of Stanley Tools.
This Warranty does not affect the statutory rights of consumer purchasers of this product.
This Warranty shall be governed by and construed in accordance with the laws of England
and Stanley Tools and the purchaser each irrevocably agrees to submit to the exclusive
jurisdiction of the courts of England over any claim or matter arising under or in connection
with this Warranty.
IMPORTANT NOTE: The customer is responsible for the correct use and care of the
instrument. Moreover, the customer is completely responsible for periodically checking the
accuracy of the laser unit, and therefore for the calibration of the instrument.
Calibration and care are not covered by warranty.
Subject to change without notice
20
77-122
© 2010 The Stanley Works
Stanley Europe, Egide Walschaertsstraat 14-16,
2800 Mechelen, Belgium
Issue 1 01/10
WWW.STANLEYWORKS.COM
Download PDF

advertising