FME142 | Stanley FME142 DRILL instruction manual

www.stanley.com.au
FME142
ENGLISH
A
B
2
(Original instructions)
(Original instructions)
Intended use
Your Stanley FatMax impact drill has been designed for
drilling in wood, metal, plastics, and masonry as well as for
screwdriving purposes. This tool is intended for professional
and private, non professional users.
Safety instructions
General power tool safety warnings
@
Warning! Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions listed below may result in electric shock,
fire and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to your mains
operated (corded) power tool or battery operated (cordless)
power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b. Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases
or dust. Power tools create sparks which may ignite the
dust or fumes.
c. Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs
with earthed (grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock
if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of
electric shock.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
ENGLISH
f. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a
power tool while you are tired or under the influence
of drugs, alcohol or medication. A moment of inattention
while operating power tools may result in serious personal
injury.
b. Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal
injuries.
c. Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or
energising power tools that have the switch on invites
accidents.
d. Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection can
reduce dust-related hazards.
4. Power tool use and care
a. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will do
the job better and safer at the rate for which it was
designed.
b. Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or the
battery pack from the power tool before making any
adjustments, changing accessories, or storing power
tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
3
ENGLISH
(Original instructions)
d. Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
5.Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
b. Power to the tool should always be supplied via
residual current device with a rated residual current of
30mA or less.
Additional power tool safety warnings
@
Warning! Additional safety warnings for drills and
impact drills
Wear ear protectors when impact drilling. Exposure to
noise can cause hearing loss.
u Use auxiliary handle(s) if supplied with the tool. Loss
of control can cause personal injury.
u Hold power tool by insulated gripping surfaces when
performing an operation where the cutting accessory
may contact hidden wiring or its own cord. Cutting accessory contacting a "live" wire may make exposed metal
parts of the power tool "live" and could give the operator
an electric shock
u Never use a chisel accessory in rotary mode. The accessory will bind in the material and rotate the drill.
u Use clamps or another practical way to secure and support the workpiece to a stable platform. Holding the work
by hand or against your body leaves it unstable and may
lead to loss of control.
u Before drilling into walls, floors or ceilings, check for the
location of wiring and pipes.
u Avoid touching the tip of a drill bit just after drilling, as it
may be hot.
u
4
u
The intended use is described in this instruction manual.
The use of any accessory or attachment or performance
of any operation with this tool other than those recommended in this instruction manual may present a risk of
personal injury and/or damage to property.
Safety of others
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a person responsible for their
safety.
u Children should be supervised to ensure that they do not
play with the appliance.
u
Residual risks.
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
u Injuries caused by touching any rotating/moving parts.
u Injuries caused when changing any parts, blades or accessories.
u Injuries caused by prolonged use of a tool. When using
any tool for prolonged periods ensure you take regular
breaks.
u Impairment of hearing.
u Health hazards caused by breathing dust developed when
using your tool (example:- working with wood, especially
oak, beech and MDF.)
Vibration
The declared vibration emission values stated in the technical
data and the declaration of conformity have been measured
in accordance with a standard test method provided by
EN 60745 and may be used for comparing one tool with
another. The declared vibration emission value may also be
used in a preliminary assessment of exposure.
Warning! The vibration emission value during actual use of
the power tool can differ from the declared value depending
on the ways in which the tool is used. The vibration level may
increase above the level stated.
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons regularly
using power tools in employment, an estimation of vibration
exposure should consider, the actual conditions of use and the
way the tool is used, including taking account of all parts of the
ENGLISH
(Original instructions)
operating cycle such as the times when the tool is switched off
and when it is running idle in addition to the trigger time.
Labels on tool
:
The following pictograms are shown on the tool:
Warning! To reduce the risk of injury, the user must
read the instruction manual.
Electrical safety
#
u
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Stanley FaxMax Service
Centre in order to avoid a hazard.
Features
This tool includes some or all of the following features.
1. Variable speed switch
2. Lock-on button
3. Variable speed control knob
4. Forward/reverse switch
5. Two-gear selector
6. Drilling mode selector
7.Chuck
8. Depth stop
9. Side handle
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting the side handle and depth stop (fig. A)
Turn the grip counterclockwise until you can slide the side
handle (9) onto the front of the tool.
u Rotate the side handle into the desired position.
u Insert the depth stop (8) into the mounting hole as shown.
u Set the drilling depth as described below.
u Tighten the side handle by turning the grip clockwise.
u
Setting the drilling depth (fig. A)
Slacken the side handle (9) by turning the grip counterclockwise.
u Set the depth stop (8) to the desired position. The maximum drilling depth is equal to the distance between the tip
of the drill bit and the front end of the depth stop.
u Tighten the side handle by turning the grip clockwise.
u
Fitting an accessory (fig. B)
Open the chuck by turning the front part (11) with one
hand while holding the rear part (13) with the other.
u Insert the bit shaft (12) into the chuck and firmly tighten
the chuck.
u
Use
Warning! Let the tool work at its own pace. Do not overload.
Warning! Before drilling into walls, floors or ceilings, check for
the location of wiring and pipes.
Selecting the drilling mode
s
For hammer drilling in masonry and concrete, set the
operating mode selector (6) to the
position
u For drilling in steel, wood and plastics, set the operating
mode selector (6) to the position.
u
r
Two-gear selector (fig. A)
For drilling in steel and for screwdriving applications, turn
the two-gear selector (5) into position 1 by aligning the
arrow (10) with the number 1 (1st gear).
u For drilling in materials other than steel, turn the two-gear
selector (5) into position 2 by aligning the arrow (10) with
the number 2 (2nd gear).
u
Selecting the direction of rotation
For drilling and tightening screws, use forward (clockwise)
rotation. For loosening screws or removing a jammed drill bit,
use reverse (counterclockwise) rotation.
u To select forward rotation, push the forward/reverse slider
(4) to the left.
u To select reverse rotation, push the forward/reverse slider
to the right.
Warning! Never change the direction of rotation while the
motor is running.
Switching on and off
To switch the tool on, press the variable speed switch (1).
The tool speed depends on how far you press the switch.
If the tool has a variable speed control knob (3), set it
to the required speed range. As a general rule, use low
speeds for large diameter drill bits and high speeds for
smaller diameter drill bits.
u For continuous operation, press the lock-on button (2) and
release the variable speed switch. This option is available
only at full speed or at any speed preset with the variable
speed control knob (3). This option does not work in
reverse rotation.
u To switch the tool off, release the variable speed switch.
To switch the tool off when in continuous operation, press
the variable speed switch once more and release it.
u
5
ENGLISH
(Original instructions)
Accessories
The performance of your tool depends on the accessory used.
Stanley FaxMax accessories are engineered to high quality
standards and designed to enhance the performance of your
tool. By using these accessories you will get the very best
from your tool.
Maintenance
Your Stanley FaxMax corded/cordless appliance/tool has been
designed to operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation depends
upon proper tool care and regular cleaning.
Warning! Before performing any maintenance on corded/
cordless power tools:
u Switch off and unplug the appliance/tool.
u Or switch off and remove the battery from the appliance/
tool if the appliance/tool has a separate battery pack.
u Or run the battery down completely if it is integral and then
switch off.
u Unplug the charger before cleaning it. Your charger does
not require any maintenance apart from regular cleaning.
u Regularly clean the ventilation slots in your appliance/tool/
charger using a soft brush or dry cloth.
u Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
u Regularly open the chuck and tap it to remove any dust
from the interior (when fitted).
Protecting the environment
Z
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your Stanley FaxMax product
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product available for separate collection.
z
Separate collection of used products and packaging allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials.
Local regulations may provide for separate collection of electrical products from the household, at municipal waste sites or
by the retailer when you purchase a new product.
6
Technical data
FME142 (Type 1)
Input voltage
VAC
230
Power input
W
850
No-load speed
Impact rate
-1
min
-1
0-1100 / 0-3100
min
0-18,700 / 0-52,700
Concrete
mm
18
Steel
mm
13
Wood
mm
50
Weight
kg
2.5
Max. drilling capacity
Level of sound pressure according to EN 60745:
Sound pressure (LpA) 92 dB(A), uncertainty (K) 3 dB(A)
Sound power (LWA) 103 dB(A), uncertainty (K) 3 dB(A)
Vibration total values (triax vector sum) according to EN 60745:
Impact drilling into concrete (ah, ID) 11 m/s2, uncertainty (K) 1.5 m/s2
Drilling into metal (ah, D) 1.5 m/s2, uncertainty (K) 1.5 m/s2
(Original instructions)
ENGLISH
7
Australia & New Zealand
Stanley Black & Decker
82 Taryn Drive, Epping, VIC 3076 Australia
Tel.1800 338 002 (Aust) or Tel. 0800 339 258 (NZ)
90610906
05/14
Download PDF