D25313K | DeWalt D25313K ROTARY HAMMER Type 3 instruction manual

www.
.eu
D25313
D25223
D25323
D25324
English (original instructions)
4
Copyright DEWALT
2
Figure 1
b
d
e
n
f
g
c
a
m
h
i
j
D25323
b
f
n
c
a
g
m
h
d
e
j
D25223
i
c
d
n
k
f
f
g
a
m
h
e
i
j
l
D25313
k
D25324
1
Figure 2
d
d
D25313, D25323,
D25324
e
e
D25223
Figure 4
Figure 3
f
g
i
2
Figure 6
Figure 5
c
j
h
Figure 7
3
EN GLI S H
HEAVY-DUTY ROTARY HAMMERDRILL
D25313, D25223, D25323, D25324
Congratulations!
You have chosen a DEWALT tool. Years of experience, thorough product development and innovation make
DEWALT one of the most reliable partners for professional power tool users.
Technical Data
Voltage
(U.K. & Ireland only)
Type
Power input
No-load speed
Load speed
Impact energy
Hammerdrilling
Chiselling
Maximum drilling range in
steel/wood/concrete
Chisel positions
Core drilling capacity in soft brick
Tool holder
Collar diameter
Weight
LPA
KPA
LWA
KWA
(sound pressure)
(sound pressure uncertainty)
(sound power)
(sound power uncertainty)
W
min-1
min-1
D25313
230
230/115
3
800
0–1,150
0–830
D25223
230
230/115
2
800
0–1,150
0–830
D25323
230
230/115
2
800
0–1,150
0–830
D25324
230
230/115
2
800
0–1,150
0–830
J
J
0–3.1
0–3.4
3.1
3.4
0–3.1
0–3.4
0–3.1
0–3.4
mm
mm
kg
13/30/26
51
65
SDS Plus®
54
3.0
13/30/26
52
65
SDS Plus®
54
3.3
13/30/26
51
65
SDS Plus®
54
3.4
13/30/26
51
65
SDS Plus®
54
3.5
dB(A)
dB(A)
dB(A)
dB(A)
85.4
3.3
99.4
3.3
88
3.9
99
3.9
85.4
3.3
99.4
3.3
85.4
3.3
99.4
3.3
V
V
mm
Vibration total values (triax vector sum) determined according to EN 60745:
Drilling into metal
Vibration emissioni value ah,D =
Uncertainty K =
m/s²
m/s²
3.0
1.6
< 2.5
1.5
< 2.5
1.5
< 2.5
1.5
Drilling into concrete
Vibration emissioni value ah,HD =
Uncertainty K =
m/s²
m/s²
18.0
1.7
9.6
1.5
10.5
1.5
10.5
1.5
Chiselling
Vibration emissioni value ah,Cheq = m/s²
Uncertainty K =
m/s²
18.0
1.5
6.4
1.5
10.5
3.5
10.5
3.5
Screwdriving without impact
Vibration emission value ah =
Uncertainty K =
< 2.5
1.5
< 2.5
1.5
< 2.5
1.5
< 2.5
1.5
4
m/s²
m/s²
DEUTSCH
The vibration emission level given in this information
sheet has been measured in accordance with a
standardised test given in EN 60745 and may be
used to compare one tool with another. It may be
used for a preliminary assessment of exposure.
WARNING: The declared vibration
emission level represents the main
applications of the tool. However if the
tool is used for different applications,
with different accessories or poorly
maintained, the vibration emission may
differ. This may significantly increase the
exposure level over the total working
period.
An estimation of the level of exposure to
vibration should also take into account
the times when the tool is switched off
or when it is running but not actually
doing the job. This may significantly
reduce the exposure level over the total
working period.
Identify additional safety measures to
protect the operator from the effects of
vibration such as: maintain the tool and
the accessories, keep the hands warm,
organisation of work patterns.
Fuses:
Europe
U.K. & Ireland
230 V tools
230 V tools
10 Amperes, mains
13 Amperes, in plugs
Definitions: Safety Guidelines
The definitions below describe the level of severity
for each signal word. Please read the manual and
pay attention to these symbols.
DANGER: Indicates an imminently
hazardous situation which, if not avoided,
will result in death or serious injury.
WARNING: Indicates a potentially
hazardous situation which, if not
avoided, could result in death or
serious injury.
CAUTION: Indicates a potentially
hazardous situation which, if not
avoided, may result in minor or
moderate injury.
NOTICE: Indicates a practice not
related to personal injury which, if
not avoided, may result in property
damage.
Denotes risk of electric shock.
Denotes risk of fire.
EC-Declaration of Conformity
MACHINERY DIRECTIVE
D25313, D25223,D25323, D25324
DEWALT declares that these products described
under “technical data” are in compliance with:
2006/42/EC, EN 60745-1, EN 60745-2-6.
These products also comply with Directive
2004/108/EC and 2011/65/EU. For more
information, please contact DEWALT at the following
address or refer to the back of the manual.
The undersigned is responsible for compilation of the
technical file and makes this declaration on behalf of
DEWALT.
Horst Grossmann
Vice President Engineering and Product
Development
DEWALT, Richard-Klinger-Straße 11,
D-65510, Idstein, Germany
10.05.2010
WARNING: To reduce the risk of injury,
read the instruction manual.
General Power Tool Safety Warnings
WARNING! Read all safety warnings
and instructions. Failure to follow the
warnings and instructions may result in
electric shock, fire and/or serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
The term “power tool” in the warnings refers
to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
1) WORK AREA SAFETY
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power
tools create sparks which may ignite the dust
or fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can
cause you to lose control.
5
EN GLI S H
2) ELECTRICAL SAFETY
a) Power tool plugs must match the outlet.
Never modify the plug in any way. Do
not use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of
electric shock.
b) Avoid body contact with earthed or
grounded surfaces such as pipes,
radiators, ranges and refrigerators. There
is an increased risk of electric shock if your
body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the
cord for carrying, pulling or unplugging
the power tool. Keep cord away from
heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the
risk of electric shock.
e) When operating a power tool outdoors,
use an extension cord suitable for outdoor
use. Use of a cord suitable for outdoor use
reduces the risk of electric shock.
f) If operating a power tool in a damp
location is unavoidable, use a residual
current device (RCD) protected supply.
Use of an RCD reduces the risk of electric
shock.
3) PERSONAL SAFETY
a) Stay alert, watch what you are doing and
use common sense when operating a
power tool. Do not use a power tool while
you are tired or under the influence of
drugs, alcohol or medication. A moment of
inattention while operating power tools may
result in serious personal injury.
b) Use personal protective equipment.
Always wear eye protection. Protective
equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce
personal injuries.
c) Prevent unintentional starting. Ensure
the switch is in the off position before
connecting to power source and/or
battery pack, picking up or carrying the
tool. Carrying power tools with your finger
on the switch or energising power tools that
have the switch on invites accidents.
d) Remove any adjusting key or wrench
before turning the power tool on. A
wrench or a key left attached to a rotating
part of the power tool may result in personal
injury.
6
e)
f)
g)
Do not overreach. Keep proper
footing and balance at all times. This
enables better control of the power tool in
unexpected situations.
Dress properly. Do not wear loose
clothing or jewellery. Keep your hair,
clothing and gloves away from moving
parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
If devices are provided for the connection
of dust extraction and collection facilities,
ensure these are connected and properly
used. Use of dust collection can reduce
dust-related hazards.
4) POWER TOOL USE AND CARE
a) Do not force the power tool. Use the
correct power tool for your application.
The correct power tool will do the job
better and safer at the rate for which it
was designed.
b) Do not use the power tool if the switch
does not turn it on and off. Any power
tool that cannot be controlled with the switch
is dangerous and must be repaired.
c) Disconnect the plug from the power
source and/or the battery pack from
the power tool before making any
adjustments, changing accessories, or
storing power tools. Such preventive safety
measures reduce the risk of starting the
power tool accidentally.
d) Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands of
untrained users.
e) Maintain power tools. Check for
misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tool’s operation.
If damaged, have the power tool repaired
before use. Many accidents are caused by
poorly maintained power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are
easier to control.
g) Use the power tool, accessories and
tool bits etc., in accordance with these
instructions taking into account the
working conditions and the work to
be performed. Use of the power tool for
operations different from those intended
could result in a hazardous situation.
DEUTSCH
5) SERVICE
a) Have your power tool serviced by a
qualified repair person using only identical
replacement parts. This will ensure that the
safety of the power tool is maintained.
Additional Specific Safety Rules for
Rotary Hammers
• Wear ear protectors. Exposure to noise can
cause hearing loss.
• Use auxiliary handles supplied with the tool.
Loss of control can cause personal injury.
• Hold power tools by insulated gripping
surfaces when performing an operation
where the cutting tool may contact hidden
wiring or its own cord. Contact with a “live”
wire will make exposed metal parts of the tool
“live” and shock the operator.
• Use clamps or other practical way to secure
and support the workpiece to a stable
platform. Holding the work by hand or against
your body is unstable and may lead to loss of
control.
• Wear safety goggles or other eye protection.
Hammering operations cause chips to fly. Flying
particles can cause permanent eye damage.
Wear a dust mask or respirator for applications
that generate dust. Ear protection may be
required for most applications.
• Keep a firm grip on the tool at all times.
Do not attempt to operate this tool
without holding it with both hands. It is
recommended that the side handle be used at
all times. Operating this tool with one hand will
result in loss of control. Breaking through or
encountering hard materials such as re-bar may
be hazardous as well. Tighten the side handle
securely before use.
• Do not operate this tool for long periods of
time. Vibration caused by hammer action may
be harmful to your hands and arms. Use gloves
to provide extra cushion and limit exposure by
taking frequent rest periods.
• Do not recondition bits yourself. Chisel
reconditioning should be done by an authorized
specialist. Improperly reconditioned chisels
could cause injury.
• Wear gloves when operating tool or
changing bits. Accessible metal parts on the
tool and bits may get extremely hot during
operation. Small bits of broken material may
damage bare hands.
• Never lay the tool down until the bit has
come to a complete stop. Moving bits could
cause injury.
• Do not strike jammed bits with a hammer to
dislodge them. Fragments of metal or material
chips could dislodge and cause injury.
• Slightly worn chisels can be resharpened by
grinding.
• Keep the power cord away from the rotating
bit. Do not wrap the cord around any part of
your body. An electric cord wrapped around a
spinning bit may cause personal injury and loss
of control.
Residual Risks
The following risks are inherent to the use of rotary
hammers:
– injuries caused by touching the rotating parts or
hot parts of the tool.
In spite of the application of the relevant safety
regulations and the implementation of safety
devices, certain residual risks cannot be avoided.
These are:
– Impairment of hearing.
– Risk of squeezing fingers when changing the
accessory.
– Health hazards caused by breathing dust
developed when working in concrete and/or
masonry.
Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual before use.
Wear ear protection.
Wear eye protection.
DATE CODE POSITION (FIG. 1)
The Date Code (n), which also includes the year of
manufacture, is printed into the housing.
Example:
2012 XX XX
Year of Manufacture
Package Contents
The package contains:
1 Heavy-duty rotary hammerdrill
7
EN GLI S H
1 Side handle
1 Depth adjustment rod
1 Kitbox
1 Keyless chuck (D25324 only)
1 Instruction manual
1 Exploded drawing
• Check for damage to the tool, parts or
accessories which may have occurred during
transport.
• Take the time to thoroughly read and
understand this manual prior to operation.
Description (fig. 1)
WARNING: Never modify the power
tool or any part of it. Damage or
personal injury could result.
a. Variable speed switch
b. Active vibration control
(D25223, D25323 and D25324 only)
c. Forward / reverse slider
d. Mode selector
e. Safety lock
f. Tool holder / locking sleeve
g. Dust cover
h. Depth adjustment rod
i. Side handle
j. Depth stop clamp
k. Locking collar (D25324 only)
l. Chuck (D25324 only)
m. Main handle
INTENDED USE
These heavy-duty rotary hammers have been
designed for professional drilling and hammerdrilling,
screwdriving and light chipping.
DO NOT use under wet conditions or in presence of
flammable liquids or gases.
These hammerdrills are professional power tools.
DO NOT let children come into contact with the
tool. Supervision is required when inexperienced
operators use this tool.
• This product is not intended for use by persons
(including children) suffering from diminished
physical, sensory or mental abilities; lack of
experience, knowledge or skills unless they are
supervised by a person responsible for their
safety. Children should never be left alone with
this product.
8
ACTIVE VIBRATION CONTROL (FIG. 1)
(D25223, D25323 AND D25324 ONLY)
The active vibration control neutralises rebound
vibration from the hammer mechanism. Lowering
hand and arm vibration allows for more comfortable
use for longer periods of time and extends the life of
the unit.
For best vibration control, hold the tool with one
hand on the main handle (m) and the other hand on
the side handle (i). Apply just enough pressure so
the hammer is approximately mid-stroke.
The hammer only needs enough pressure to engage
the active vibraton control. Applying too much
pressure will not make the tool drill or chip faster and
active vibration control will not engage.
TORQUE LIMITING CLUTCH
All rotary hammer drills are equipped with a torque
limiting clutch that reduces the maximum torque
reaction transmitted to the operator in case of
jamming of a drill bit. This feature also prevents the
gearing and electric motor from stalling. The torque
limiting clutch has been factory-set and cannot be
adjusted.
Electrical Safety
The electric motor has been designed for one
voltage only. Always check that the power supply
corresponds to the voltage on the rating plate.
Your DEWALT charger is double insulated
in accordance with EN 60745; therefore
no earth wire is required.
WARNING: 115 V units have to
be operated via a fail-safe isolating
transformer with an earth screen
between the primary and secondary
winding.
If the supply cord is damaged, it must be replaced
by a specially prepared cord available through the
DEWALT service organization.
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
• Safely dispose of the old plug.
• Connect the brown lead to the live terminal in
the plug.
• Connect the blue lead to the neutral terminal.
WARNING: No connection is to be
made to the earth terminal.
Follow the fitting instructions supplied with good
quality plugs. Recommended fuse: 13 A.
DEUTSCH
Using an Extension Cable
If an extension cable is required, use an approved
3–core extension cable suitable for the power
input of this tool (see technical data).The minimum
conductor size is 1.5 mm2; the maximum length is
30 m.
When using a cable reel, always unwind the cable
completely.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of
injury, turn unit off and disconnect
machine from power source before
installing and removing accessories,
before adjusting or changing set-ups
or when making repairs. Be sure the
trigger switch is in the OFF position. An
accidental start-up can cause injury.
Selecting the Operating Mode
(fig. 2)
D25313, D25323, D25324
The tool can be used in the following operating
modes:
Rotary drilling: for screwdriving and for
drilling into steel, wood and plastics.
1. To select the operating mode, press the safety
lock (e) and rotate the mode selector switch
(d) until it points to the symbol of the required
mode.
2. Release the safety lock and check that the
mode selector switch is locked in place.
WARNING: Do not select the operating
mode when the tool is running.
Indexing the Chisel Position (fig. 2)
The chisel can be indexed and locked into 51/52
different positions.
1. Rotate the mode selector switch (d) until it
points to the bit rotation symbol.
2. Rotate the chisel in the desired position.
3. Set the mode selector switch (d) to the
hammering only position.
4. Twist the chisel until it locks in position.
Inserting and Removing SDS Plus®
Accessories (fig. 3)
This tool uses SDS Plus® accessories (refer to
the inset in figure 3 for a cross-section of an SDS
Plus® bit shank). We recommend using professional
accessories only.
1. Clean and grease the bit shank.
Hammerdrilling: for concrete and masonry
drilling operations.
2. Insert the bit shank into the tool holder/locking
sleeve (f).
Hammering only: for light chipping,
chiselling and demolition applications. In
this mode the tool can also be used as a
lever to free a jammed drill bit.
3. Push the bit down and turn it slightly until it fits
into the slots.
Bit rotation: non-working position used
only to rotate a flat chisel into the desired
position.
D25223
The tool can be used in the following operating
modes:
Rotary drilling: for screwdriving and for
drilling into steel, wood and plastics.
Hammerdrilling: for concrete and masonry
drilling operations.
Bit rotation: non-working position used
only to rotate a flat chisel into the desired
position.
Hammering only: for light chipping,
chiselling and demolition applications. In
this mode the tool can also be used as a
lever to free a jammed drill bit.
4. Pull on the bit to check if it is properly locked.
The hammering function requires the bit to be
able to move axially several centimetres when
locked in the tool holder.
5. To remove a bit, pull back the tool holder/
locking sleeve (f) and pull out the bit.
WARNING: Always wear gloves when
you change accessories. The exposed
metal parts on the tool and accessory
may become extremly hot during
operation.
Fitting the Side Handle (fig. 4)
The side handle (i) can be fitted to suit both RH- and
LH-users.
WARNING: Do not use the tool without
the side handle properly assembled.
1. Loosen the side handle.
9
EN GLI S H
2. For RH-users: slide the side handle clamp
over the collar behind the tool holder, handle at
the left.
For LH-users: slide the side handle clamp over
the collar behind the tool holder, handle at the
right.
3. Rotate the side handle to the desired position
and tighten the handle.
Setting the Drilling Depth (fig. 5)
1. Insert the required drill bit as described above.
2. Press the depth stop clamp (j) and keep it
depressed.
3. Fit the depth adjustment rod (h) through the
hole in the depth stop clamp.
4. Adjust the drilling depth as shown.
5. Release the depth stop clamp.
Forward/reverse Slider (fig. 6)
1. Push the forward/reverse slider (c) to the
LH-side for forward (RH) rotation. See arrows
on tool.
2. Push the forward/reverse slider (c) to the
RH-side for reverse (LH) rotation.
WARNING: Always wait until the motor
has come to a complete standstill
before changing the direction of rotation.
Fitting a Chuck Adapter and Chuck
(Sold Separately)
1. Screw a chuck onto the threaded end of the
chuck adapter.
2. Insert the connected chuck and adapter in the
tool as though it were a standard SDS Plus® bit.
3. To remove the chuck, proceed as for removing
a standard SDS Plus® bit.
WARNING: Never use standard chucks
in the hammerdrilling mode.
Consult your dealer for further information on the
appropriate accessories.
Replacing the Tool Holder with the
Chuck (fig. 1)
D25324
1. Turn the locking collar (k) into the unlocking
position and pull the tool holder/locking sleeve
(f) off.
2. Push the chuck (l) onto the spindle and turn the
locking collar into the locking position.
10
3. To replace the chuck with the tool holder, first
remove the chuck the same way as the tool
holder was removed. Then place the tool holder
the same way as the chuck was placed.
WARNING: Never use standard chucks
in the hammerdrilling mode.
Replacing the Dust Cover (fig. 3)
The dust cover (g) prevents dust ingress into the
mechanism. Replace a worn dust cover immediately.
1. Pull back the tool holder locking sleeve (f) and
pull the dust cover (g) off.
2. Fit the new dust cover.
3. Release the tool holder locking sleeve.
OPERATION
Instructions for Use
WARNING:
• Always observe the safety instructions
and applicable regulations.
• Be aware of the location of pipework
and wiring.
• Apply only a gentle pressure to
the tool (approx. 5 kg). Excessive
force does not speed up drilling but
decreases tool performance and may
shorten tool life.
• Do not drill or drive too deep to
prevent damage to the dust cover.
• Always hold the tool firmly with both
hands and ensure a secure stance
(fig. 7). Always operate the tool with
the side handle properly mounted.
Proper Hand Position (fig. 1, 7)
WARNING: To reduce the risk of
serious personal injury, ALWAYS use
proper hand position as shown.
WARNING: To reduce the risk of
serious personal injury, ALWAYS hold
securely in anticipation of a sudden
reaction.
Proper hand position requires one hand on the side
handle (i), with the other hand on the main handle
(m).
Overload Clutch
If the drill bit becomes jammed or caught, the drive
to the drill spindle is interrupted by the overload
clutch. Because of the forces that occur as a result,
DEUTSCH
always hold the machine securely with both hands
and take a firm stance.
Switching On and Off (fig. 1)
1. To run the tool, press the variable speed switch
(a). The pressure exerted on the variable speed
switch determines the tool speed.
2. To stop the tool, release the switch.
3. To lock the tool in the off position, move the
forward/reverse slider (c) to the central position.
Rotary Drilling (fig. 1)
1. Set the mode selector switch (d) to the rotary
drilling position.
2. Fit the chuck adapter/chuck assembly.
3. Proceed as described for hammerdrilling.
WARNING: Never use standard chucks
in the hammerdrilling mode.
Screwdriving (fig. 1)
Hammerdrilling (fig. 1)
1. Set the mode selector switch (d) to the rotary
drilling position.
DRILLING WITH A SOLID BIT
2. Select the direction of rotation.
1. Set the mode selector switch (d) to the
hammerdrilling position.
3. Insert the special SDS Plus® screwdriving
adaptor for use with hexagonal screwdriver bits.
2. Insert the appropriate drill bit.
4. Insert the appropriate screwdriver bit. When
driving slotted head screws always use bits with
a finder sleeve.
NOTE: For best results use high quality carbidetipped bits.
3. Adjust the side handle (i) as required.
4. If necessary, set the drilling depth.
5. Mark the spot where the hole is to be drilled.
6. Place the drill bit on the spot and switch on the
tool.
7. Always switch off the tool when work is finished
and before unplugging.
Drilling with a Core Bit (fig. 1)
1. Set the mode selector (d) to the hammerdrilling
position.
5. Gently press the variable speed switch (a) to
prevent damage to the screw head. In reverse
(LH) rotation the tool speed is automatically
reduced for easy screw removal.
6. When the screw is flush with the workpiece,
release the variable speed switch to prevent
the screw head from penetrating into the
workpiece.
Chipping and Chiselling (fig. 1)
1. Set the mode selector switch (d) to the
hammering only position.
2. Adjust the side handle (i) as required.
2. Insert the appropriate chisel and rotate it by
hand to lock it into one of 51/52 positions.
3. Insert the appropriate core bit.
3. Adjust the side handle (i) as required.
4. Assemble the centredrill into the core bit.
4. Switch on the tool and start working.
5. Place the centredrill on the spot and press the
variable speed switch (a). Drill until the core
penetrates into the concrete approx. 1 cm.
5. Always switch off the tool when work is finished
and before unplugging.
6. Stop drilling and remove the centredrill. Place
the core bit back into the hole and continue
drilling.
7. When drilling through a structure thicker than
the depth of the core bit, break away the round
cylinder of concrete or core inside the bit at
regular intervals. To avoid unwanted breaking
away of concrete around the hole, first drill a
hole the diameter of the center drill completely
through the structure. Then drill the cored hole
halfway from each side.
8. Always switch off the tool when work is finished
and before unplugging.
WARNING:
• Do not use this tool to mix or pump
easily combustible or explosive fluids
(benzine, alcohol, etc.).
• Do not mix or stir flammable liquids
labelled accordingly.
MAINTENANCE
Your DEWALT power tool has been designed to
operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
WARNING: To reduce the risk of
injury, turn unit off and disconnect
machine from power source before
11
EN GLI S H
installing and removing accessories,
before adjusting or changing set-ups
or when making repairs. Be sure the
trigger switch is in the OFF position. An
accidental start-up can cause injury.
• This machine is not user-serviceable. Take the
tool to an authorised DEWALT repair agent after
approximately 40 hours of use. If problems
occur before this time contact an authorised
DEWALT repair agent.
• The tool will automatically switch off when the
carbon brushes are worn.
Motor Brushes
DEWALT uses an advanced brush system which
automatically stops the drill when the brushes wear
out. This prevents serious damage to the motor.
New brush assemblies are available at authorised
DEWALT service centers. Always use identical
replacement parts.
Lubrication
Your power tool requires no additional lubrication.
be hazardous. To reduce the risk of
injury, only DEWALT recommended
accessories should be used with this
product.
Various types of SDS Plus® drill bits and chisels are
available as an option.
Consult your dealer for further information on the
appropriate accessories.
Protecting the Environment
Separate collection. This product must
not be disposed of with normal
household waste.
Should you find one day that your DEWALT product
needs replacement, or if it is of no further use to you,
do not dispose of it with household waste. Make this
product available for separate collection.
Separate collection of used products
and packaging allows materials to be
recycled and used again. Re-use of
recycled materials helps prevent
environmental pollution and reduces
the demand for raw materials.
Accessories and attachments used must be
regularly lubricated around the SDS Plus® fitment.
Local regulations may provide for separate collection
of electrical products from the household, at
municipal waste sites or by the retailer when you
purchase a new product.
Cleaning
DEWALT provides a facility for the collection and
recycling of DEWALT products once they have
reached the end of their working life. To take
advantage of this service please return your product
to any authorised repair agent who will collect them
on our behalf.
WARNING: Blow dirt and dust out of
the main housing with dry air as often as
dirt is seen collecting in and around the
air vents. Wear approved eye protection
and approved dust mask when
performing this procedure.
WARNING: Never use solvents or
other harsh chemicals for cleaning the
non-metallic parts of the tool. These
chemicals may weaken the materials
used in these parts. Use a cloth
dampened only with water and mild
soap. Never let any liquid get inside the
tool; never immerse any part of the tool
into a liquid.
Optional Accessories
WARNING: Since accessories, other
than those offered by DEWALT, have
not been tested with this product, use
of such accessories with this tool could
12
You can check the location of your nearest
authorised repair agent by contacting your local
DEWALT office at the address indicated in this
manual. Alternatively, a list of authorised DEWALT
repair agents and full details of our after-sales
service and contacts are available on the Internet at:
www.2helpU.com.
ENGLISH
GUARANTEE
DEWALT is confident of the quality of its
products and offers an outstanding guarantee
for professional users of the product. This
guarantee statement is in addition to and in
no way prejudices your contractual rights as a
professional user or your statutory rights as a
private non-professional user. The guarantee
is valid within the territories of the Member
States of the European Union and the
European Free Trade Area.
• 30 DAY NO RISK SATISFACTION GUARANTEE •
If you are not completely satisfied with the
performance of your DEWALT tool, simply
return it within 30 days, complete with all
original components, as purchased, to
the point of purchase, for a full refund or
exchange. The product must have been
subject to fair wear and tear and proof of
purchase must be produced.
• ONE YEAR FREE SERVICE CONTRACT •
If you need maintenance or service for your
DEWALT tool, in the 12 months following
purchase, you are entitled to one service free
of charge. It will be undertaken free of charge
at an authorised DEWALT repair agent. Proof
of purchase must be produced. Includes
labour. Excludes accessories and spare parts
unless failed under warranty.
• ONE YEAR FULL WARRANTY •
If your DEWALT product becomes defective
due to faulty materials or workmanship
within 12 months from the date of purchase,
DEWALT guarantees to replace all defective
parts free of charge or – at our discretion –
replace the unit free of charge provided that:
• The product has not been misused;
• The product has been subject to fair
wear and tear;
• Repairs have not been attempted by
unauthorised persons;
• Proof of purchase is produced;
• The product is returned complete with all
original components.
If you wish to make a claim, contact your
seller or check the location of your nearest
authorised DEWALT repair agent in the
DEWALT catalogue or contact your DEWALT
office at the address indicated in this manual.
A list of authorised DEWALT repair agents and
full details of our after-sales service is available
on the Internet at: www.2helpU.com.
13
Belgique et
Luxembourg
België en
Luxemburg
Black & Decker - DEWALT
Nieuwlandlaan 7, IZ Aarschot B156
B-3200 Aarschot
Danmark
DEWALT
Sluseholmen 2-4
2450 København SV
Tlf:
70201511
Fax: 70224910
www.dewalt.dk
Deutschland
DEWALT
Richard Klinger Str. 11
65510 Idstein
Tel:
06126-21-1
Fax: 06126-21-2770
www.dewalt.de
Ελλάς
Black & Decker (Ελλάς) Α.Ε.
Στράβωνος 7 & Βουλιαγμένης 159
Γλυφάδα 16674, Αθήνα
España
DEWALT
Parque de Negocios “Mas Blau”
Edificio Muntadas, c/Bergadá, 1, Of. A6
08820 El Prat de Llobregat (Barcelona)
Tel:
934 797 400
Fax: 934 797 419
www.dewalt.es
France
DEWALT
5, allée des hêtres
BP 30084, 69579 Limonest Cedex
Tel:
04 72 20 39 20
Fax: 04 72 20 39 00
www.dewalt.fr
Schweiz
Suisse
Svizzera
DEWALT
In der Luberzen 40
8902 Urdorf
Tel:
01 - 730 67 47
Fax: 01 - 730 70 67
www.dewalt.ch
Ireland
DEWALT
Calpe House Rock Hill
Black Rock, Co. Dublin
Tel:
00353-2781800
Fax: 00353-2781811
www.dewalt.ie
Italia
DEWALT
c/o Energypark Building 03 sud, Via Monza 7/A,
20871 Vimercate (MB), IT
Tel:
800-014353
Fax: 39 039 9590 317
www.dewalt.it
Nederlands
Black & Decker - DEWALT
Joulehof 12
4600 AB Bergen Op Zoom
Tel:
31 164 283 063
Fax: 31 164 283 200
www.dewalt.nl
Norge
DEWALT
Postboks 4613, Nydalen
0405 Oslo
Tel:
45 25 13 00
Fax: 45 25 08 00
www.dewalt.no
Österreich
DEWALT
Werkzeug Vertriebsges m.b.H
Oberlaaerstrasse 248
A-1230 Wien
Tel:
01 - 66116 - 0
Fax: 01 - 66116 - 14
www.dewalt.at
Portugal
DEWALT
Centro de Escritórios de Sintra Avenida Almirante
Gago Coutinho, 132/134, Edifício 142710-418 Sintra
2710-418 Lisboa
Tel:
214 66 75 00
Fax: 214 66 75 75
www.dewalt.pt
Suomi
DEWALT
Tekniikantie 12
02150 Espoo, Finland
Puh: 010 400 430
Faksi: 0800 411 340
www.dewalt.fi
Sverige
DEWALT
Box 94
431 22 Mölndal
Tel:
031 68 61 00
Fax: 031 68 60 08
www.dewalt.se
Türkiye
KALE Hırdavat ve Makina A.Ş.
Defterdar Mah. Savaklar Cad. No:15
Edirnekapı / Eyüp / İSTANBUL 34050 TÜRKİYE
Tel: 0212 533 52 55
Faks: 0212 533 10 05
www.dewalt.com.tr
United
Kingdom
DEWALT
210 Bath Road; Slough, Berks SL1 3YD
Middle East
Africa
DEWALT
P.O. Box - 17164,
Jebel Ali (South Zone), Dubai, UAE
N181424
Dutch Tel: 32 70 220 063
French Tel: 32 70 220 062
Τηλ:
30 210 8981-616
Service: 30 210 8981-616
Φαξ:
30 210 8983-570
Tel:
Fax:
01753-56 70 55
01753-57 21 12
Fax: 32 70 225 585
Fax: 32 70 222 441
www.dewalt.be
www.dewalt.gr
www.dewalt.co.uk
Tel:
971 4 8863030
Fax: 971 4 8863333
www.dewalt.ae
05/12
Download PDF