D25330K | DeWalt D25330K CHIPPING HAMMER Type 3 instruction manual

www.
.eu
D25330
Copyright DEWALT
2
Figure 1
b a
d
c
g
e
h
f
1
Figure 2
Figure 3
d
c
e
Figure 4
Figure 5
b
f
2
Figure 6
3
EN GLI S H
CHIPPING HAMMER
D25330
An estimation of the level of exposure to
vibration should also take into account
the times when the tool is switched off
or when it is running but not actually
doing the job. This may significantly
reduce the exposure level over the total
working period.
Congratulations!
You have chosen a DEWALT tool. Years of
experience, thorough product development and
innovation make DEWALT one of the most reliable
partners for professional power tool users.
Technical Data
Voltage
(U.K. & Ireland only)
Type
Power input
Impact rate
Impact energy
Chisel positions
Tool holder
Collar diameter
Weight
LPA (sound pressure)
KPA (sound pressure
uncertainty)
LWA (sound power)
KWA (sound power
uncertainty)
mm
kg
D25330
230
230/115
2
650
4,100
3.1
12
SDS Plus®
54
2.9
dB(A)
85.5
dB(A)
dB(A)
1.9
102
dB(A)
1.9
V
V
W
min-1
J
Vibration total values (triax vector sum) determined
according to EN 60745:
Vibration emission value ah
Chiselling
ah,Cheq =
Uncertainty K =
m/s²
m/s²
17
1.9
The vibration emission level given in this information
sheet has been measured in accordance with a
standardised test given in EN 60745 and may be
used to compare one tool with another. It may be
used for a preliminary assessment of exposure.
WARNING: The declared vibration
emission level represents the main
applications of the tool. However if the
tool is used for different applications,
with different accessories or poorly
maintained, the vibration emission may
differ. This may significantly increase the
exposure level over the total working
period.
4
Identify additional safety measures to
protect the operator from the effects of
vibration such as: maintain the tool and
the accessories, keep the hands warm,
organisation of work patterns.
Fuses:
Europe
U.K. & Ireland
U.K. & Ireland
230 V tools
230 V tools
115 V tools
10 Amperes, mains
13 Amperes, in plugs
16 Amperes, in plugs
Definitions: Safety Guidelines
The definitions below describe the level of severity
for each signal word. Please read the manual and
pay attention to these symbols.
DANGER: Indicates an imminently
hazardous situation which, if not avoided,
will result in death or serious injury.
WARNING: Indicates a potentially
hazardous situation which, if not
avoided, could result in death or
serious injury.
CAUTION: Indicates a potentially
hazardous situation which, if not
avoided, may result in minor or
moderate injury.
NOTICE: Indicates a practice not
related to personal injury which, if
not avoided, may result in property
damage.
Denotes risk of electric shock.
Denotes risk of fire.
ENGLISH
EC-Declaration of Conformity
MACHINERY DIRECTIVE
OUTDOOR NOISE DIRECTIVE
D25330
DEWALT declares that these products described
under “technical data” are in compliance with:
98/37/EC (until Dec. 28, 2009), 2006/42/EC (from
Dec. 29, 2009), EN 60745-1, EN 60745-2-6.
2000/14/EC, Electrical concrete breaker (hand-held),
m ≤ 15 kg, Annex VIII, TÜV Rheinland Product
Safety GmbH (0197), D-51105 Köln, Germany,
Notified Body ID No.: 0197
Level of acoustic power according to 2000/14/EC
(Article 12, Annex III, No. 10; m ≤ 15 kg):
LWA (measured sound power level)
dB
103
LWA (guaranteed sound power level)
dB
105
These products also comply with Directive
2004/108/EC. For more information, please contact
DEWALT at the following address or refer to the
back of the manual.
The undersigned is responsible for compilation of the
technical file and makes this declaration on behalf of
DEWALT.
Horst Grossmann
Vice President Engineering and Product
Development
DEWALT, Richard-Klinger-Straße 11,
D-65510, Idstein, Germany
03.08.2009
WARNING: To reduce the risk of injury,
read the instruction manual.
General Power Tool Safety Warnings
WARNING! Read all safety warnings
and instructions Failure to follow the
warnings and instructions may result in
electric shock, fire and/or serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
The term “power tool” in the warnings refers
to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
1) WORK AREA SAFETY
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power
tools create sparks which may ignite the dust
or fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can
cause you to lose control.
2) ELECTRICAL SAFETY
a) Power tool plugs must match the outlet.
Never modify the plug in any way. Do
not use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of
electric shock.
b) Avoid body contact with earthed or
grounded surfaces such as pipes,
radiators, ranges and refrigerators. There
is an increased risk of electric shock if your
body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the
cord for carrying, pulling or unplugging
the power tool. Keep cord away from
heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the
risk of electric shock.
e) When operating a power tool outdoors,
use an extension cord suitable for outdoor
use. Use of a cord suitable for outdoor use
reduces the risk of electric shock.
f) If operating a power tool in a damp
location is unavoidable, use a residual
current device (RCD) protected supply.
Use of an RCD reduces the risk of electric
shock.
3) PERSONAL SAFETY
a) Stay alert, watch what you are doing and
use common sense when operating a
power tool. Do not use a power tool while
you are tired or under the influence of
drugs, alcohol or medication. A moment of
inattention while operating power tools may
result in serious personal injury.
b) Use personal protective equipment.
Always wear eye protection. Protective
equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce
personal injuries.
5
EN GLI S H
c)
d)
e)
f)
g)
Prevent unintentional starting. Ensure
the switch is in the off position before
connecting to power source and/or
battery pack, picking up or carrying the
tool. Carrying power tools with your finger
on the switch or energising power tools that
have the switch on invites accidents.
Remove any adjusting key or wrench
before turning the power tool on. A
wrench or a key left attached to a rotating
part of the power tool may result in personal
injury.
Do not overreach. Keep proper
footing and balance at all times. This
enables better control of the power tool in
unexpected situations.
Dress properly. Do not wear loose
clothing or jewellery. Keep your hair,
clothing and gloves away from moving
parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
If devices are provided for the connection
of dust extraction and collection facilities,
ensure these are connected and properly
used. Use of dust collection can reduce
dust-related hazards.
4) POWER TOOL USE AND CARE
a) Do not force the power tool. Use the
correct power tool for your application.
The correct power tool will do the job
better and safer at the rate for which it
was designed.
b) Do not use the power tool if the switch
does not turn it on and off. Any power
tool that cannot be controlled with the switch
is dangerous and must be repaired.
c) Disconnect the plug from the power
source and/or the battery pack from
the power tool before making any
adjustments, changing accessories, or
storing power tools. Such preventive safety
measures reduce the risk of starting the
power tool accidentally.
d) Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands of
untrained users.
e) Maintain power tools. Check for
misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tool’s operation.
If damaged, have the power tool repaired
before use. Many accidents are caused by
poorly maintained power tools.
6
f)
g)
Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are
easier to control.
Use the power tool, accessories and
tool bits etc., in accordance with these
instructions taking into account the
working conditions and the work to
be performed. Use of the power tool for
operations different from those intended
could result in a hazardous situation.
5) SERVICE
a) Have your power tool serviced by a
qualified repair person using only identical
replacement parts. This will ensure that the
safety of the power tool is maintained.
Additional Specific Safety Rules for
Chipping Hammer
• Wear ear protectors. Exposure to noise can
cause hearing loss.
• Hold power tools by insulated gripping
surfaces when performing an operation
where the cutting tool may contact hidden
wiring or its own cord. Cutting accessory
contacting a “live” wire may make exposed
metal parts of the tool “live” and shock the
operator.
Be certain that the material being drilled does
not conceal electric or gas service and that
their locations have been verified with the utility
companies.
• Use auxiliary handles supplied with the
tool. Loss of control can cause personal injury.
Keep a firm grip on the tool at all times. Do not
attempt to operate this tool without holding it
with both hands. Operating this tool with one
hand will result in loss of control. Breaking
through or encountering hard materials such as
re-bar may be hazardous as well. Tighten the
side handle securely before use.
• Use clamps or other practical way to secure
and support the workpiece to a stable
platform. Holding the work by hand or against
your body is unstable and may lead to loss of
control.
• Wear ear protectors when hammering
for extended periods of time. Prolonged
exposure to high intensity noise can cause
hearing loss. Temporary hearing loss or serious
ear drum damage may result from high sound
levels generated by hammerdrilling.
ENGLISH
• Wear safety goggles or other eye protection.
Hammering and drilling operations cause chips
to fly. Flying particles can cause permanent eye
damage. Wear a dust mask or respirator for
applications that generate dust.
• Hammer bits and tools get hot during
operation. Wear gloves when touching them.
– Health hazards caused by breathing dust
developed when working in concrete and/or
masonry.
Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual
before use.
• Keep a firm grip on the tool at all times.
Do not attempt to operate this tool
without holding it with both hands. It is
recommended that the side handle be used at
all times. Operating this tool with one hand will
result in loss of control. Breaking through or
encountering hard materials such as re-bar may
be hazardous as well.
• Do not operate this tool for long periods of
time. Vibration caused by hammer action may
be harmful to your hands and arms. Use gloves
to provide extra cushion and limit exposure by
taking frequent rest periods.
• Do not recondition bits yourself. Chisel
reconditioning should be done by an authorized
specialist. Improperly reconditioned chisels
could cause injury.
• Never lay the tool down until the bit has
come to a complete stop. Moving bits could
cause injury.
Wear ear protection.
Wear eye protection.
DATE CODE POSITION (FIG. 1)
The Date Code (h), which also includes the year of
manufacture, is printed into the housing.
Example:
2009 XX XX
Year of Manufacture
Package Contents
The package contains:
1 Chipping hammer
• Do not strike jammed bits with a hammer to
dislodge them. Fragments of metal or material
chips could dislodge and cause injury.
1 Side handle
• Slightly worn chisels can be resharpened by
grinding.
1 Instruction manual
• Keep the power cord away from the rotating
bit. Do not wrap the cord around any part of
your body. An electric cord wrapped around a
spinning bit may cause personal injury and loss
of control.
Residual Risks
The following risks are inherent to the use of
chipping hammers:
– Injuries caused by touching the hot parts of the
tool.
In spite of the application of the relevant safety
regulations and the implementation of safety
devices, certain residual risks cannot be avoided.
These are:
1 Kitbox (K models)
1 Exploded drawing
• Check for damage to the tool, parts or
accessories which may have occurred during
transport.
• Take the time to thoroughly read and
understand this manual prior to operation.
Description (fig. 1)
WARNING: Never modify the power
tool or any part of it. Damage or
personal injury could result.
a. On/off switch
b. Lock-on slider
c. Chisel position index collar
d. Tool holder/locking sleeve
– Impairment of hearing.
e. Dust cover
– Risk of squeezing fingers when changing the
accessory.
g. Main handle
f. Side handle
7
EN GLI S H
INTENDED USE
Your chipping hammer has been designed for light
chipping, chiselling and demolition applications.
DO NOT use under wet conditions or in presence of
flammable liquids or gases.
These chipping hammers are professional power
tools.
DO NOT let children come into contact with the
tool. Supervision is required when inexperienced
operators use this tool.
Electrical Safety
The electric motor has been designed for one
voltage only. Always check that the power supply
corresponds to the voltage on the rating plate.
Your DEWALT tool is double insulated in
accordance with EN 60745; therefore no
earth wire is required.
WARNING: 115 V units have to
be operated via a fail-safe isolating
transformer with an earth screen
between the primary and secondary
winding.
If the supply cord is damaged, it must be replaced
by a specially prepared cord available through the
DEWALT service organization.
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
WARNING: To reduce the risk of
injury, turn unit off and disconnect
machine from power source before
installing and removing accessories,
before adjusting or changing set-ups
or when making repairs. Be sure the
trigger switch is in the OFF position. An
accidental start-up can cause injury.
Inserting and Removing SDS Plus®
Accessories (fig. 2)
This tool uses SDS Plus® accessories (refer to the
inset in figure 2 for a cross-section of an SDS Plus®
bit shank). We recommend to use professional
accessories only.
1. Clean and grease the bit shank.
2. Insert the bit shank into the tool holder/locking
sleeve (d).
3. Push the bit down and turn it slightly until it fits
into the slots.
4. Pull on the bit to check if it is properly locked.
The hammering function requires the bit to be
able to move axially several centimetres when
locked in the tool holder/locking sleeve.
5. To remove a bit pull back the tool holder/locking
sleeve (d) and pull out the bit.
Indexing the Chisel Position (fig. 3)
The chisel can be indexed and locked into 12
different positions.
• Safely dispose of the old plug.
1. Insert the chisel as described above.
• Connect the brown lead to the live terminal in
the plug.
2. Rotate the collar (c) in the direction of the
arrowuntil the chisel is in the desired position.
• Connect the blue lead to the neutral terminal.
WARNING: No connection is to be
made to the earth terminal.
Follow the fitting instructions supplied with good
quality plugs. Recommended fuse: 13 A.
Using an Extension Cable
If an extension cable is required, use an approved
extension cable suitable for the power input of this
tool (see technical data).
The minimum conductor size is 1.5 mm2. When
using a cable reel, always unwind the cable
completely.
8
ASSEMBLY AND ADJUSTMENTS
Fitting the Side Handle (fig. 4)
The side handle (f) can be fitted to suit both RH- and
LH-users. Always use the tool with the side handle
properly assembled.
1. Loosen the side handle.
– For RH-users, slide the side handle clamp
over the collar behind the tool holder, handle
at the left.
– For LH-users, slide the side handle clamp
over the collar behind the tool holder/locking
sleeve, handle at the right.
2. Rotate the side handle to the desired position
and tighten the handle.
ENGLISH
Replacing the Dust Cover (fig. 2)
Chipping and Chiselling (fig. 1)
The dust cover (e) prevents dust from entering into
the mechanism.
Insert the appropriate chisel and rotate it into one of
12 positions.
IMPORTANT: Replace a worn dust cover immediately.
Turn the tool on the tool and start working.
1. Pull back the tool holder/locking sleeve (d) and
pull the dust cover (e) off.
2. Fit the new dust cover.
3. Release the tool holder/locking sleeve.
OPERATION
Instructions for Use
WARNING:
• Always observe the safety instructions
and applicable regulations.
• Be aware of the location of pipework
and wiring.
• Apply a pressure of approx. 5 kg to
the tool. Excessive force does not
speed up chiselling but decreases tool
performance and may shorten tool life.
Proper Hand Position (fig. 1, 6)
WARNING: To reduce the risk of
serious personal injury, ALWAYS use
proper hand position as shown.
WARNING: To reduce the risk of
serious personal injury, ALWAYS hold
securely in anticipation of a sudden
reaction.
Proper hand position requires one hand on the
side handle (f), with the other hand on the main
handle (g).
Switching On and Off (fig. 1, 5)
To run the tool, press the on/off switch (a).
For continuous operation, press and hold down the
switch (a), slide the lock-on slider (b) into the lock
position and release the switch.
To stop the tool, release the switch.
To stop the tool in continuous operation, press the
switch briefly and release it. Always switch off the
tool when work is finished and before unplugging.
Always turn the tool off when work is finished and
before unplugging.
MAINTENANCE
Your DEWALT power tool has been designed to
operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
WARNING: To reduce the risk of
injury, turn unit off and disconnect
machine from power source before
installing and removing accessories,
before adjusting or changing set-ups
or when making repairs. Be sure the
trigger switch is in the OFF position. An
accidental start-up can cause injury.
Lubrication
Your power tool requires no additional lubrication.
Accessories and attachments used must be
regularly lubricated around the SDS Plus® fitment.
Cleaning
WARNING: Blow dirt and dust out of
the main housing with dry air as often as
dirt is seen collecting in and around the
air vents. Wear approved eye protection
and approved dust mask when
performing this procedure.
WARNING: Never use solvents or
other harsh chemicals for cleaning the
non-metallic parts of the tool. These
chemicals may weaken the materials
used in these parts. Use a cloth
dampened only with water and mild
soap. Never let any liquid get inside the
tool; never immerse any part of the tool
into a liquid.
9
EN GLI S H
Optional Accessories
WARNING: Since accessories, other
than those offered by DEWALT, have
not been tested with this product, use
of such accessories with this tool could
be hazardous. To reduce the risk of
injury, only DEWALT, recommended
accessories should be used with this
product.
Various types of SDS Plus® chisels are available as
an option.
Consult your dealer for further information on the
appropriate accessories.
Protecting the Environment
Separate collection. This product must
not be disposed of with normal
household waste.
Should you find one day that your DEWALT product
needs replacement, or if it is of no further use to you,
do not dispose of it with household waste. Make this
product available for separate collection.
Separate collection of used products
and packaging allows materials to be
recycled and used again. Re-use of
recycled materials helps prevent
environmental pollution and reduces
the demand for raw materials.
Local regulations may provide for separate collection
of electrical products from the household, at
municipal waste sites or by the retailer when you
purchase a new product.
DEWALT provides a facility for the collection and
recycling of DEWALT products once they have
reached the end of their working life. To take
advantage of this service please return your product
to any authorised repair agent who will collect them
on our behalf.
You can check the location of your nearest
authorised repair agent by contacting your local
DEWALT office at the address indicated in this
manual. Alternatively, a list of authorised DEWALT
repair agents and full details of our after-sales
service and contacts are available on the Internet at:
www.2helpU.com.
10
GUARANTEE
DEWALT is confident of the quality of its
products and offers an outstanding guarantee
for professional users of the product. This
guarantee statement is in addition to and in
no way prejudices your contractual rights as a
professional user or your statutory rights as a
private non-professional user. The guarantee is
valid within the territories of the Member States
of the European Union and the European Free
Trade Area.
• 30 DAY NO RISK
SATISFACTION GUARANTEE •
If you are not completely satisfied with the
performance of your DEWALT tool, simply return
it within 30 days, complete with all original
components, as purchased, to the point of
purchase, for a full refund or exchange. The
product must have been subject to fair wear and
tear and proof of purchase must be produced.
• ONE YEAR FREE SERVICE CONTRACT •
If you need maintenance or service for your
DEWALT tool, in the 12 months following
purchase, it will be undertaken free of charge
at an authorised DEWALT repair agent. Proof of
purchase must be produced. Includes labour.
Excludes accessories and spare parts unless
failed under warranty.
• ONE YEAR FULL WARRANTY •
If your DEWALT product becomes defective
due to faulty materials or workmanship within
12 months from the date of purchase, DEWALT
guarantees to replace all defective parts free of
charge or – at our discretion – replace the unit
free of charge provided that:
• The product has not been misused;
• The product has been subject to fair wear
and tear;
• Repairs have not been attempted by
unauthorised persons;
• Proof of purchase is produced;
• The product is returned complete with all
original components.
If you wish to make a claim, contact your seller
or check the location of your nearest authorised
DEWALT repair agent in the DEWALT catalogue
or contact your DEWALT office at the address
indicated in this manual. A list of authorised
DEWALT repair agents and full details of our
after-sales service is available on the Internet at:
www.2helpU.com.
11
12
13
Belgique et Luxembourg
België en Luxemburg
Black & Decker - DEWALT
Nieuwlandlaan 7, IZ Aarschot B156
B-3200 Aarschot
Tel:
+32 (0)015 - 15 47 9211
Fax:
+32 (0)015 - 15 47 9210
www.dewalt.be
Danmark
DEWALT
Sluseholmen 2-4
2450 København SV
Tlf:
70201511
Fax:
70224910
www.dewalt.dk
Deutschland
DEWALT
Richard-Klinger-Straße
65510 Idstein
Tel:
06126-21-1
Fax:
06126-21-2770
www.dewalt.de
Ελλάς
Black & Decker (Hellas) S.A.
Στράβωνος 7 & Βουλιαγμένης 159
Γλυφάδα 16674, Αθήνα
Τηλ:
(01) 8981-616
Φαξ:
(01) 8983-570
Service: (01) 8982-630
España
DEWALT
Parque de Negocios “Mas Blau”
Edificio Muntadas, c/Bergadá, 1, Of. A6
08820 El Prat de Llobregat (Barcelona)
Tel:
934 797 400
Fax:
934 797 439
www.dewalt.es
France
DEWALT
5, allée des hêtres
BP 30084, 69579 Limonest Cedex
Tel:
04 72 20 39 20
Fax:
04 72 20 39 00
www.dewalt.fr
Schweiz
Suisse
Svizzera
DEWALT
In der Luberzen 40
8902 Urdorf
Tel:
01 - 730 67 47
Fax:
01 - 730 70 67
www.dewalt.ch
Ireland
DEWALT
Calpe House Rock Hill
Black Rock, Co. Dublin
Tel:
00353-2781800
Fax:
00353-2781811
www.dewalt.ie
Italia
DEWALT
Viale Elvezia 2
20052 Monza (Mi)
Tel:
800-014353
Fax:
039-2387592
www.dewalt.it
Nederlands
Black & Decker - DEWALT
Joulehof 12
4600 AB Bergen Op Zoom
Tel:
0164 283000
Fax:
0164 283100
www.dewalt.nl
Norge
DEWALT
Postboks 4814, Nydalen
0422 Oslo
Tel:
22 90 99 00
Fax:
22 90 99 01
www.dewalt.no
Österreich
DEWALT
Werkzeugevertriebs GmbH
Erlaaerstraße 165, Postfach 320,1231 Wien
Tel:
01 - 66116 - 0
Fax:
01 - 66116 - 14
www.dewalt.at
Portugal
DEWALT
Rua Egas Moniz 173
João do Estoril, 2766-651 Estoril
Tel:
214 66 75 00
Fax:
214 66 75 75
www.dewalt.pt
Suomi
DEWALT Oy
Tekniikantie 12
02150 Espoo, Finland
Puh:
010 400 430
Faksi: 0800 411 340
www.dewalt.fi
DEWALT Oy
Teknikvägen 12
02150 Esbo, Finland
Tel:
010 400 430
Fax:
0800 411 340
www.dewalt.fi
Sverige
DEWALT
Box 94
431 22 Mölndal
Tel:
031 68 61 00
Fax:
031 68 60 08
www.dewalt.se
Türkiye
KALE Hırdavat ve Makina A.Ş.
Defterdar Mah. Savaklar Cad. No:15
Edirnekapı / Eyüp / İSTANBUL 34050 TÜRKİYE
Tel:
0212 533 52 55
Faks: 0212 533 10 05
www.dewalt.com.tr
United Kingdom
DEWALT
210 Bath Road
Slough, Berks SL1 3YD
Tel:
01753-56 70 55
Fax:
01753-57 21 12
www.dewalt.co.uk
N042189
09/09
Download PDF

advertising