INSTRUCTION MANUAL
DCR017-XE
CHARGER/RADIO
• Remove the battery pack. Switch off before leaving it unattended. Remove the
battery pack when not in use, before changing accessories or attachments and
before servicing.
• This appliance is intended to be used in moderate climates.
• This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
• Charger/radio shall not be exposed to dripping or splashing; no objects filled with
liquids, such as vases, shall be placed on it.
• No exposed flame sources, such as lighted candles, should be placed on the
charger/radio.
• Mains plug is used as the disconnect device; the disconnect device (plug) shall
remain readily operable.
• Young children and the infirm. This appliance is not intended for use by young
children or infirm persons without supervision.
– This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
– Children should be supervised to ensure that they do not play with the appliance.
• Replacement of the supply cord. If the supply cord or plug is damaged, it must
be replaced by the manufacturer or an authorised DEWALT Service Centre in
order to avoid a hazard.
Definitions: Safety Guidelines
The definitions below describe the level of severity for each signal
word. Please read the manual and pay attention to these symbols.
DANGER: Indicates an imminently hazardous situation which, if
not avoided, will result in death or serious injury.
WARNING: Indicates a potentially hazardous situation which, if
not avoided, could result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if
not avoided, may result in minor or moderate injury.
NOTICE: Indicates a practice not related to personal injury which,
if not avoided, may result in property damage.
IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL,
CALL US AT: 1800 338 002 (Aust) or 0800 339 258 (NZ).
Technical Data
Power source
Mains voltage
Battery voltage
Battery type
Weight
Approx. charging time
Charge current
VAC
VDC
kg
min
Amp
DCR017
AC/DC
230–240
10.8–18
Li-Ion
5.7
45 –120
2.0
Important Safety Instructions for Charger/Radios
SAVE THESE INSTRUCTIONS: This manual contains important safety and operating
instructions for the DCR017 charger/radio.
• Before using charger/radio, read all instructions and cautionary markings on
charger, battery pack, and product using battery pack.
DANGER: Electrocution hazard. 230 volts are present at charging terminals. Do not
probe with conductive objects. Electric shock or electrocution may result.
Safety Instructions for Charger/Radios
• Do not abuse cord. Never carry the charger/radio by its cord. Never pull the
cord to disconnect from the socket. Keep the cord away from heat, oil and sharp
edges.
1
• Do not operate charger/radio if it has received a sharp blow, been dropped, or
otherwise damaged in any way. Take it to an authorised service center.
• Do not disassemble charger/radio; take it to an authorised service center
when service or repair is required. Incorrect reassembly may result in a risk of
electric shock, electrocution or fire.
• Disconnect the charger/radio from the outlet before attempting any cleaning.
This will reduce the risk of electric shock. Removing the battery pack will not
reduce this risk.
• NEVER attempt to connect 2 chargers together.
• The DCR017 charger/radio is designed to operate on standard 230 V
household electrical power. Do not attempt to use it on any other voltage. This
does not apply to the vehicular charger.
WARNING: Shock hazard. Do not allow any liquid to get inside charger/radio.
Electric shock may result.
WARNING: Batteries (battery pack) shall not be exposed to excessive heat such as
sunshine, fire or the like.
CAUTION: Burn hazard. To reduce the risk of injury, charge only DEWALT
rechargeable batteries. Other types of batteries may burst causing personal injury and
damage.
CAUTION: Danger of explosion if internal battery is incorrectly replaced. Replace
only with the same or equivalent type.
NOTICE: Under certain conditions, with the charger/radio plugged in to the power
supply, the exposed charging contacts inside the charger/radio can be shorted by
foreign material. Foreign materials of a conductive nature such as, but not limited to,
steel wool, aluminum foil, or any buildup of metallic particles should be kept away
from charger/radio cavities. Always unplug the charger/radio from the power supply
when there is no battery pack in the cavity. Unplug charger/radio before attempting to
clean.
• DO NOT attempt to charge the battery pack with any charger/radio other than
the one in this manual. The charger/radio and battery pack are specifically
designed to work together.
• These charger/radios are not intended for any uses other than charging
DEWALT rechargeable batteries. Any other uses may result in risk of fire, electric
shock or electrocution.
• Do not expose charger/radio to rain or snow.
• Pull by plug rather than cord when disconnecting charger/radio. This will
reduce risk of damage to electric plug and cord.
• Make sure that cord is located so that it will not be stepped on, tripped over,
or otherwise subjected to damage or stress.
• Do not use an extension cord unless it is absolutely necessary. Use of improper
extension cord could result in risk of fire, electric shock, or electrocution.
• Do not place any object on top of charger/radio or place the charger/radio
on a soft surface that might block the ventilation slots and result in excessive
internal heat. Place the charger/radio in a position away from any heat source.
• Do not operate charger/radio with damaged cord or plug — have them
replaced immediately.
SAVE THESE INSTRUCTIONS
Grounding Instructions
The DCR017 (230 V) charger/radio must be grounded. In the event of malfunction
or breakdown, grounding provides a path of least resistance for electric current to
reduce the risk of electric shock. The charger/radio is equipped with a cord having
an equipment-grounding conductor and a grounding plug. The plug must be plugged
into an appropriate outlet that is properly installed and grounded in accordance with all
local codes and ordinances.
DANGER: Improper connection of the equipment-grounding conductor can result
in a risk of electric shock. The conductor with insulation having an outer surface
that is green with yellow stripes is the equipment-grounding conductor. If repair
or replacement of the cord or plug is necessary, do not connect the equipmentgrounding conductor to a live terminal. Repairs shall only be performed by a DEWALT
service agent. Do not modify the plug provided with the charger/radio – if it will not fit
the outlet, have a proper outlet installed by a DEWALT repair agent.
FOR GROUNDED, CORD-CONNECTED CHARGER/RADIO RATED 16A AND LOWER
AND INTENDED FOR USE ON A NOMINAL 230 V SUPPLY CIRCUIT
The charger/radio is for use on a nominal 230 V circuit, and has a grounding plug that
looks like the plug in the following illustration.
2
FIG. 1
READ ALL INSTRUCTIONS
DCR017
• Do not charge or use the battery pack in explosive atmospheres, such as in
the presence of flammable liquids, gases or dust. Inserting or removing the
battery pack from the charger may ignite the dust or fumes.
• Never force the battery pack into the charger. Do not modify the battery pack
in any way to fit into a non-compatible charger as battery pack may rupture
causing serious personal injury. Consult the chart at the end of this manual for
compatibility of batteries and chargers.
• Charge the battery packs only in designated DEWALT chargers.
• DO NOT splash or immerse in water or other liquids.
• Do not store or use the tool and battery pack in locations where the
temperature may reach or exceed 40 °C (105 °F) (such as outside sheds
or metal buildings in summer). For best life store battery packs in a cool, dry
location.
• Batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
WARNING: Fire hazard. Never attempt to open the battery pack for any reason. If
the battery pack case is cracked or damaged, do not insert into the charger. Do not
crush, drop or damage the battery pack. Do not use a battery pack or charger that
has received a sharp blow, been dropped, run over or damaged in any way (e.g.,
pierced with a nail, hit with a hammer, stepped on). Damaged battery packs should be
returned to the service center for recycling.
WARNING: Fire hazard. Do not store or carry the battery pack so that metal objects
can contact exposed battery terminals. For example, do not place the battery pack
in aprons, pockets, tool boxes, product kit boxes, drawers, etc., with loose nails,
screws, keys, etc. Transporting batteries can possibly cause fires if the battery
terminals inadvertently come in contact with conductive materials such as keys,
coins, hand tools and the like. When transporting individual battery packs, make sure
that the battery terminals are protected and well insulated from materials that could
contact them and cause a short circuit.
SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM ION (Li-Ion)
• Do not incinerate the battery pack even if it is severely damaged or is
completely worn out. The battery pack can explode in a fire. Toxic fumes and
materials are created when lithium ion battery packs are burned.
Extension Cords
CAUTION: Use only extension cords that are approved by the country’s Electrical
Authority. Before using extension cords, inspect them for loose or exposed wires,
damaged insulation and defective fittings. Replace the cord if necessary.
WARNING: We recommend the use of a residual current device with a residual
current rating of 30mA or less.
• The label on your appliance may include the following symbols. The symbols and
their definitions are as follows:
V ................. volts
A ...............amperes
Hz ............... hertz
W ..............watts
min ............. minutes
...........alternating current
........ direct current
...........alternating or direct current
.............. Class I Construction
.............earthing terminal
................... (grounded)
..............safety alert symbol
.............. Class II Construction
…/min .......per minute
................... (double insulated)
SAVE ALL WARNINGS AND INSTRUCTIONS FOR
FUTURE REFERENCE
Important Safety Instructions for All Battery Packs
When ordering replacement battery packs, be sure to include the catalog number and
voltage. Consult the chart at the end of this manual for compatibility of chargers and
battery packs.
The battery pack is not fully charged out of the carton. Before using the battery pack
and charger, read the safety instructions below and then follow charging procedures
outlined.
3
Indicator Light Operation
• If battery contents come into contact with the skin, immediately wash area
with mild soap and water. If battery liquid gets into the eye, rinse water over the
open eye for 15 minutes or until irritation ceases. If medical attention is needed,
the battery electrolyte is composed of a mixture of liquid organic carbonates and
lithium salts.
• Contents of opened battery cells may cause respiratory irritation. Provide fresh
air. If symptoms persist, seek medical attention.
WARNING: Burn hazard. Battery liquid may be flammable if exposed to spark or
flame.
PACK CHARGING
PACK CHARGED
HOT/COLD DELAY
x
Battery Charger Function
Your DCR017 DEWALT radio can be also use as DEWALT Battery charger. Be sure to
read all charger safety instruction before using this function.
Only XR 10.8V, 14.4V and 18V Li-Ion slide battery are compatible with this charger.
PROBLEM PACK OR CHARGER
PROBLEM POWERLINE
Charge Indicators
This charger is designed to detect certain problems that can arise. Problems are indicated
by the red light flashing at a fast rate. If this occurs, re-insert the battery pack into the
charger. If the problem persists, try a different battery pack to determine if the charger
is working properly. If the new pack charges correctly, then the original pack is defective
and should be returned to a service center or other collection site for recycling. If the new
battery pack elicits the same trouble indication as the original, have the charger and the
battery pack tested at an authorized service center.
HOT/COLD DELAY
This charger has a hot/cold delay feature: when the charger detects a battery that is
hot, it automatically starts a delay, suspending charging until the battery has cooled.
After the battery has cooled, the charger automatically switches to the pack charging
mode. This feature ensures maximum battery life. The red light flashes long, then
short while in the hot/cold delay mode.
LEAVING THE BATTERY PACK IN THE CHARGER
The charger and battery pack can be left connected with the charge indicator showing
Pack Charged.
WEAK BATTERY PACKS: Weak batteries will continue to function but should not be
expected to perform as much work.
FAULTY BATTERY PACKS: This charger will not charge a faulty battery pack. The
charger will indicate faulty battery pack by refusing to light or by displaying problem pack
or charger.
Charging Process (Fig. 2, 3)
1. Plug the charger/radio into an appropriate outlet before inserting the battery pack.
2. Insert the battery pack (J) into the charger, as
FIG. 2
shown in Figure 1, making sure the pack is
fully seated in charger. The red (charging)
J
light will blink continuously, indicating that the
charging process has started.
3. The completion of charge will be indicated by
the red light remaining ON continuously. The
pack is fully charged and may be used at this
time or left in the charger.
Refer to the Indicator Light Operation table for the
state of charge of the battery pack.
The charge indicator light (I) will indicate the state of charge of the battery pack, when
a battery is being charged.
4
power supply when there is no battery pack in the cavity. Unplug the charger/
radio before attempting to clean.
7. Do not freeze or immerse the charger in water or any other liquid.
WARNING: Shock hazard. Don’t allow any liquid to get inside the charger. Electric
shock may result.
WARNING: Burn hazard. Do not submerge the battery pack in any liquid or allow
any liquid to enter the battery pack. Never attempt to open the battery pack for any
reason. If the plastic housing of the battery pack breaks or cracks, return to a service
center for recycling.
NOTE: This could also mean a problem with a charger.
PROBLEM POWERLINE
Some chargers have a problem powerline indicator. When the charger is used with
some portable power sources such as generators or sources that convert DC to AC, the
charger may temporarily suspend operation, flashing the red light with two fast blinks
followed by a pause. This indicates the power source is out of limits.
Important Charging Notes
1. Longest life and best performance can be obtained if the battery pack is charged
when the air temperature is between 18 ° – 24 °C (65 °F and 75 °F). DO NOT
charge the battery pack in an air temperature below +4 °C (+40 °F), or above
+40 °C (+105 °F). This is important and will prevent serious damage to the
battery pack.
2. The charger and battery pack may become warm to the touch while charging.
This is a normal condition, and does not indicate a problem. To facilitate the
cooling of the battery pack after use, avoid placing the charger or battery pack in
a warm environment such as in a metal shed or an uninsulated trailer.
3. A cold battery pack will charge at about half the rate of a warm battery pack. The
battery pack will charge at that slower rate throughout the entire charging cycle
and will not return to maximum charge rate even if the battery pack warms.
4. If the battery pack does not charge properly:
a. Check operation of receptacle by plugging in a lamp or other appliance;
b. Check to see if receptacle is connected to a light switch which turns power off
when you turn out the lights;
c. Move the charger and battery pack to a location where the surrounding air
temperature is approximately 18 ° – 24 °C (65 °F and 75 °F);
d. If charging problems persist, take the tool, battery pack and charger to your
local service center.
5. The battery pack should be recharged when it fails to produce sufficient power
on jobs which were easily done previously. DO NOT CONTINUE to use under
these conditions. Follow the charging procedure. You may also charge a partially
used pack whenever you desire with no adverse effect on the battery pack.
6. Foreign materials of a conductive nature such as, but not limited to, grinding dust,
metal chips, steel wool, aluminum foil, or any buildup of metallic particles should
be kept away from charger cavities. Always unplug the charger/radio from the
Storage Recommendations
1. The best storage place is one that is cool and dry, away from direct sunlight and
excess heat or cold.
2. For long storage, it is recommended to store a fully charged battery pack in a
cool dry place out of the charger for optimal results.
NOTE: Battery packs should not be stored completely depleted of charge. The battery
pack will need to be recharged before use.
SAVE ALL WARNINGS AND INSTRUCTIONS FOR
FUTURE REFERENCE
COMPONENTS (FIG. 3)
WARNING: Never modify the power tool or any part of it. Damage or personal
injury could result.
A. Power button
F. Memory buttons
B. Volume dial
G. Enter/Display button
C. Arrow buttons
H. LCD display
D. Mode button
I. Charging light
E. Menu button
5
FIG. 3
B
POWER
3-4
1-2
H
3. Unscrew the screw (K) on the battery door (L).
4. Press down on the battery door latch and pull to open.
5. Install the coin cell battery (M) according to the diagram inside the coin cell
battery area.
6. Replace the battery door, insert screw and tighten.
7. Securely close the battery compartment.
NOTE: To reset the LCD display, clock and presets, remove the coin cell battery and
re-install it. Follow this procedure if the screen seems to lock in place.
F
I
5-6
FM
9-10
7-8
MEM
MODE
MENU
ENT/DIS
A
POWER
E
OPERATION
MODE
WARNING: Always observe the safety instructions and applicable regulations.
WARNING: Do not place the charger/radio in locations where it may be exposed to
dripping or splashing.
D
MENU
ENT/DIS
C
G
Installing and Removing the Battery Pack (Fig. 2, 5)
NOTE: To ensure maximum performance and life of Li-Ion FIG. 5
N
batteries, charge the battery for a minimum of 10 hours
before first use.
1. Release the latch (N) to open the battery
compartment cover.
2. Insert the battery pack (J) into the receptacle until it
is
fully seated.
3. Close and latch the battery compartment cover.
To remove the battery pack from the charger/radio, press the release button and firmly
pull the battery pack out of the receptacle.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal injury, turn the tool off and
disconnect the battery pack before making any adjustments or removing/installing
attachments or accessories. An accidental start-up can cause injury.
To Install the Coin Cell Battery (Fig. 4)
WARNING: When replacing battery, replace it with the same brand and type.
Observe correct polarity (+ and –) when replacing batteries. Do not store or carry
batteries so that metal objects can contact exposed battery terminals.
FIG. 3
Your radio is equipped with memory capacity
in order to store the time and your selected
memory channels. When the radio is OFF,
K
M
this memory capacity is powered by one
coin cell battery that is included with the
radio.
1. Turn the charger/radio off and unplug
from the power source.
2. Open the battery compartment by lifting
L
the battery compartment latch.
FUEL GAUGE BATTERY PACKS (FIG. 5)
Some DEWALT battery packs include a
fuel gauge which consists of three green
LED lights that indicate the level of charge
remaining in the battery pack.
To actuate the fuel gauge, press and hold
the fuel gauge button (Q). A combination
of the three green LED lights will illuminate
designating the level of charge left. When
6
FIG. 5
Q
To perform an Auto Scan:
1. Press the menu button (E), scroll through the options by pressing the right arrow
button (C) until you reach Auto Scan and select this option by pressing the Enter/
Display button (G).
2. Press the right arrow button to select the ‘Yes’ option.
3. Press the Enter/Display button (G) to perform the Auto Scan.
Once Auto Scan is complete the radio will play the first station it finds.
To use presets please reference To Program the Memory Buttons.
DAB MODE – STATION PRUNE
Some stations once received by your radio which are no longer available may display
with a ? after the station name.
To remove these stations from the station list use the Prune function:
1. Press Menu (E) and scroll right to the Prune option.
2. Press Enter/Display (G) to select.
3. Scroll right to the Yes option, then press the Enter/Display (G) button to prune
stations.
DAB MODE – DYNAMIC RANGE COMPRESSION (DRC)
This function reduces the difference between the loudest and quietest audio being
broadcast. Effectively, this makes quiet sounds comparatively louder, and loud sounds
comparatively quieter.
The following options are available:
• 0 - broadcast DRC will be ignored
• 1/2 - sets DRC at half the level transmitted
• 1 - uses the DRC level transmitted
• 2 - doubles the DRC level transmitted
NOTE: DRC only works if it is enabled by the broadcaster.
FM/AM MODE – TUNING
To Tune: Push the right arrow to move the tuner up the frequency band, push the left
arrow to move the tuner down the frequency band.
the level of charge in the battery is below the usable limit, the fuel gauge will not
illuminate and the battery will need to be recharged.
NOTE: The fuel gauge is only an indication of the charge left on the battery pack.
It does not indicate tool functionality and is subject to variation based on product
components, temperature and end-user application.
For more information regarding fuel gauge battery packs, please contact Stanley Black
& Decker, 82 Taryn Drive, Epping, VIC 3076 Australia or call 1800 338 002 or (NZ)
0800 339 258.
AC Operation (fig. 1)
Unwrap power cord and plug into 230 V AC wall outlet.
Operating the Radio (fig. 3)
POWER/VOLUME ADJUSTMENT
1. To turn the radio on, press the power button (A).
NOTE: When the radio is first used it will enter DAB mode and automatically scan
for stations. It will then set the time and start playing the first station it finds.
If there is no time signal available please refer to Programming The Clock to
manually set the time.
2. Turn the dial (B) clockwise to increase the volume. To decrease the volume, turn
anti-clockwise.
MODE SELECTION
To choose one of the mode functions (DAB, FM, or AUX) push the mode button (D)
until the desired function is found. For example, if the radio is on DAB, seen in upper
left portion of LCD display (H), push the mode button twice to change to AUX.
DAB MODE - TUNING
When the unit is first switched on in DAB/DAB+ mode the radio will auto scan to find
broadcast stations in the local area.
Use the left or right arrow buttons (C) to scroll through the stations.
NOTE: When moving locations or if reception was poor in the original scan (possible
if the antenna was not up), this may result in an empty or incomplete list of available
stations. Manually running an Auto Scan will find all available broadcast stations.
7
To Seek: Press and hold the right arrow button (C) once and release. The tuner frequency will increase to seek the first radio station with acceptable clarity and
stop at that station. The right arrow button may be pressed again to continue
seeking a radio station at higher frequencies. The left arrow button may be
pressed to seek radio stations at lower frequencies. The seek function is
available in AM and FM modes.
PROGRAMMING THE MEMORY BUTTONS
Ten DAB and ten FM radio stations may be independently set. After programming
the buttons, pressing 1, 2, 3, 4 or 5 will instantly change the frequency to the preset
station.
1. Set the radio to desired station (see Tuning).
2. Press and hold one of the desired memory buttons (F) until the preset number
begins flashing in the LCD display (H). Release the button and wait for the preset
display to stop flashing.
3. Each memory button can store two preset stations. To store a second preset
repeat step 1.
4. Press and hold one of the desired memory buttons (F) until the preset number
begins flashing in the LCD display (H). Press the preset button a second time so
that the next preset number displays. Release the button and wait for the preset
display to stop flashing.
PROGRAMMING THE CLOCK
The time and date can be updated manually or automatically synchronised with
national time signals broadcast over DAB (where available).
To synchronise the clock automatically:
(DAB mode ONLY)
NOTE: When the radio is first used it will enter DAB mode and automatically scan for
stations.
1. Press the Menu button (E).
2. Use the arrow buttons (C) to scroll to Clock Adjust and press the Enter/Display
button (G).
3. Scroll to Sync Time Now press the Enter/Display button to select. This
automatically synchronises clock with national time signals.
To adjust the clock manually:
(FM and DAB mode)
1. Press the Menu button (E).
2. Use the arrow buttons (C) to scroll to Clock Adjust on the LCD display and press
the Enter/Display button (G).
3. Scroll to Date & Time and press the Enter/Display button (G).
4. Set the date and time using left and right arrow buttons (C).
5. Once the desired time is set press the Enter/Display (G) button to commit.
Other Clock Adjust menu options:
• Time format: Select a 12h or 24h time display format
• Date format: Select the date display format, MM/DD/YYYY, YYYY/MM/DD or DD/
MM/YYYY.
TO ADJUST THE EQ
Sound can be adjusted by changing the equalization of the bass or treble of the radio.
1. Press the Menu button (E) and scroll using the left or right arrow buttons (C) to
select Sound EQ. Select by pressing the Enter/Display button (G).
2. Press the right arrow button to increase the bass or the left arrow button to
decrease it.
3. Once desired adjustment is achieved, press the Enter/Display button (G).
4. Repeat steps 2 and 3 for treble adjustment.
Important Radio Notes (Fig. 6)
1. The radio will run up to 8 hours on a fully charged 4.0 amp hour battery. Using
batteries of lower voltage or capacity will result in less run time.
2. Reception will vary depending on location and strength of radio signal.
3. Certain generators may cause background noise.
8
Repairs
4. AM reception will most likely be clearer when powered FIG. 6
by a battery pack.
5. To use the auxiliary port (O), plug the output jack from
a CD or iPod®*/MP3 player into the port (fig. 1). The
sound from the external source plays through the
O
speakers of the DCR017.
6. The USB power output port (P) is a connection port
for powering low power devices such as mobile
P
phones, CD and MP3 players.
* iPod is a registered trademark of Apple Inc.
This charger and battery pack are not serviceable. Servicing at an authorized service
centre is required to avoid damage to static sensitive internal components.
To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment
(including brush inspection and replacement) should be performed by certified
service centers or other qualified service organizations, always using identical
replacement parts.
Accessories
WARNING: Since accessories, other than those offered by DEWALT, have not been
tested with this product, use of such accessories with this tool could be hazardous.
To reduce the risk of injury, only DEWALT recommended accessories should be used
with this product.
Recommended accessories for use with your tool are available at extra cost from
your local service center. If you need any assistance in locating any accessory, please
contact Stanley Black & Decker, 82 Taryn Drive, Epping, VIC 3076 Australia or call
1800 338 002 or (NZ) 0800 339 258.
MAINTENANCE
WARNING: To reduce the risk of serious personal injury, turn the unit off and
disconnect the battery pack before making any adjustments or removing/installing
attachments or accessories. An accidental start-up can cause injury.
Cleaning
WARNING: Blow dirt and dust out of all air vents with clean, dry air at least once
a week. To minimize the risk of eye injury, always wear AS/NZS1337 approved eye
protection when performing this.
WARNING: Never use solvents or other harsh chemicals for cleaning the
non-metallic parts of the unit. These chemicals may weaken the plastic materials
used in these parts. Use a cloth dampened only with water and mild soap. Never let
any liquid get inside the tool; never immerse any part of the tool into a liquid.
CHARGER CLEANING INSTRUCTIONS
WARNING: Shock hazard. Disconnect the charger from the AC outlet before
cleaning. Dirt and grease may be removed from the exterior of the charger using a
cloth or soft non-metallic brush. Do not use water or any cleaning solutions.
9
Stanley Black & Decker
82 Taryn Drive, Epping, VIC 3076 Australia • 1800 338 002 (Aust) or 0800 339 258 (NZ)
www.dewalt.com.au • www.dewalt.co.nz
(APR13)
Part No. N294527
DCR017-XE
Copyright © 2013 DEWALT
The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme; the “D” shaped air intake grill; the array of pyramids on the handgrip;
the kit box configuration; and the array of lozenge-shaped humps on the surface of the tool.
Download PDF

advertising