DWE6005 | DeWalt DWE6005 LAMINATE TRIMMER instruction manual

DWE6005
Final Page size: A5 (148mm x 210mm)
English (original instructions)4
Copyright DeWALT
B
Fig. A
1
15
5
3
15
16
4
12
6
2
21
8
17
9
10
13
19
7
22
11
14
20
14
25
23
18
10
21
24
26
1
Fig. B
1
Fig. C
Fig. D
3
4
15
16
3
5
16
Fig. E
6
10
2
Fig. F
Fig. G
Fig. H
25
23
24
3
English
LAMINATE TRIMMER
DWE6005
Congratulations!
You have chosen a DeWALT tool. Years of experience, thorough product development and innovation make DeWALT one of the
most reliable partners for professional power tool users.
Technical Data
Voltage
Type
Power output
No load speed
Cutting depth
Cutters diameter (max)
Collet size (max)
Weight
DWE6005- QS
230
1
590
16000 – 34000
22
25.4
6
2.1
DWE6005- GB
230
1
590
16000 – 34000
22
25.4
6.35
2.1
DWE6005- LX
115
1
620
16000 – 35000
22
25.4
6.35
2.1
78
89
78
89
78
89
dB(A)
3
3
3
m/s2
m/s2
< 2.5
1.5
< 2.5
1.5
< 2.5
1.5
VAC
W
min-1
mm
mm
mm
kg
Noise values and vibration values (triax vector sum) according to EN60745:
LPA(emission sound pressure level)
dB(A)
LWA(sound power level)
dB(A)
K(uncertainty for the given sound level)
Vibration emission value ah =
Uncertainty K =
The vibration emission level given in this information sheet has
been measured in accordance with a standardised test given in
EN60745 and may be used to compare one tool with another. It
may be used for a preliminary assessment of exposure.
WARNING: The declared vibration emission level
represents the main applications of the tool. However if
the tool is used for different applications, with different
accessories or poorly maintained, the vibration emission
may differ. This may significantly increase the exposure
level over the total working period.
An estimation of the level of exposure to vibration should
also take into account the times when the tool is switched
off or when it is running but not actually doing the job.
This may significantly reduce the exposure level over the
total working period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool
and the accessories, keep the hands warm, organisation
of work patterns.
EC-Declaration of Conformity
Machinery Directive
Laminate Trimmer
DWE6005
DeWALT declares that these products described under
Technical Data are in compliance with:
2006/42/EC, EN60745-1:2009+A11:2010, EN60745-2-17:2010.
These products also comply with Directive 2014/30/EU and
2011/65/EU. For more information, please contact DeWALT at
the following address or refer to the back of the manual.
The undersigned is responsible for compilation of the technical
file and makes this declaration on behalf of DeWALT.
Markus Rompel
Director Engineering
DeWALT, Richard-Klinger-Straße 11,
D-65510, Idstein, Germany
06.03.2018
WARNING: To reduce the risk of injury, read the
instruction manual.
4
English
Definitions: Safety Guidelines
The definitions below describe the level of severity for each
signal word. Please read the manual and pay attention to
these symbols.
DANGER: Indicates an imminently hazardous
situation which, if not avoided, will result in death or
serious injury.
WARNING: Indicates a potentially hazardous situation
which, if not avoided, could result in death or
serious injury.
CAUTION: Indicates a potentially hazardous situation
which, if not avoided, may result in minor or
moderate injury.
NOTICE: Indicates a practice not related to
personal injury which, if not avoided, may result in
property damage.
Denotes risk of electric shock.
Denotes risk of fire.
General Power Tool Safety Warnings
WARNING: Read all safety warnings, instructions,
illustrations and specifications provided with this
power tool. Failure to follow all instructions listed below
may result in electric shock, fire and/or serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
The term “power tool” in the warnings refers to your mainsoperated (corded) power tool or battery-operated (cordless)
power tool.
1) Work area safety
a ) Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b ) Do not operate power tools in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks which
may ignite the dust or fumes.
c ) Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose control.
2) Electrical safety
a ) Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk of
electric shock.
b ) Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if
your body is earthed or grounded.
c ) Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d ) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of
electric shock.
e ) When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
f ) If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
3) Personal safety
a ) Stay alert, watch what you are doing and use
common sense when operating a power tool. Do not
use a power tool while you are tired or under the
influence of drugs, alcohol or medication. A moment
of inattention while operating power tools may result in
serious personal injury.
b ) Use personal protective equipment. Always wear
eye protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection used
for appropriate conditions will reduce personal injuries.
c ) Prevent unintentional starting. Ensure the switch
is in the off position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your finger on the
switch or energising power tools that have the switch on
invites accidents.
d ) Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached
to a rotating part of the power tool may result in
personal injury.
e ) Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power tool
in unexpected situations.
f ) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g ) If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection
can reduce dust-related hazards.
4) Power tool use and care
a ) Do not force the power tool. Use the correct power
tool for your application. The correct power tool
will do the job better and safer at the rate for which it
was designed.
b ) Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
c ) Disconnect the plug from the power source and/or
the battery pack from the power tool before making
any adjustments, changing accessories, or storing
5
English
d )
e )
f )
g )
power tools. Such preventive safety measures reduce the
risk of starting the power tool accidentally.
Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users.
Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
Use the power tool, accessories and tool bits etc.,
in accordance with these instructions taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
5) Service
a ) Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Additional Safety Rules for Trimmers
•
•
•
•
•
Hold power tool by insulated gripping surfaces, because
the cutter may contact its own cord. Cutting a "live" witre
may make exposed metal parts of the power tool "live" and
shock the operator.
Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holidng the
work by your hand or against the body leaves it unstable and
may lead to loss of control.
Never run the motor unit when it is not inserted in one of
the router bases. The motor is not designed to be handheld.
Always use straight-cutters, rabbet-cutters, profile cutters,
slotter cutters or grooved knives with a shank diameter of
6 – 6.35 (1/4") mm which corresponds to the size of the collet
in your tool.
Always use cutters suitable for a speed of 35000 min-1 and
marked accordingly.
WARNING: Never use cutters with a diameter exceeding
the maximum diameter indicated in the technical data.
For slotter cutters, the maximum shank diameter MUST be
6.35 mm and the maximum diameter MUST be 25.4 mm.
For grooved knives, the maximum shank diameter MUST be
6.35 mm, the maximum diameter MUST be 25.4 mm and the
maximum cutting width MUST be 4 mm.
WARNING: We recommend the use of a residual current
device with a residual current rating of 30mA or less.
•
•
6
Residual Risks
In spite of the application of the relevant safety regulations
and the implementation of safety devices, certain residual risks
cannot be avoided. These are:
• Impairment of hearing.
• Risk of personal injury due to flying particles.
• Risk of burns due to accessories becoming hot
during operation.
• Risk of personal injury due to prolonged use.
Electrical Safety
The electric motor has been designed for one voltage only.
Always check that the power supply corresponds to the voltage
on the rating plate.
Your DeWALT tool is double insulated in accordance
with EN60745; therefore no earth wire is required.
WARNING: 115 V units have to be operated via a fail-safe
isolating transformer with an earth screen between the
primary and secondary winding.
If the supply cord is damaged, it must be replaced by a
specially prepared cord available through the DeWALT
service organisation.
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
• Safely dispose of the old plug.
• Connect the brown lead to the live terminal in the plug.
• Connect the blue lead to the neutral terminal.
WARNING: No connection is to be made to the
earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 13 A.
Using an Extension Cable
If an extension cable is required, use an approved 3–core
extension cable suitable for the power input of this tool (see
Technical Data).The minimum conductor size is 1.5 mm2; the
maximum length is 30 m.
When using a cable reel, always unwind the cable completely.
Package Contents
The package contains:
1 Motor unit
1 Collet 6 mm (6.35 / 1/4")
1 Wrench # 17 mm
1 Straight edge guide
1 Roller bearing guider
1 Dust Extraction Adaptor
1 Instruction manual
• Check for damage to the tool, parts or accessories which may
have occurred during transport.
• Take the time to thoroughly read and understand this manual
prior to operation.
English
Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual before use.
Wear ear protection.
Wear eye protection.
Date Code Position (Fig. A)
The date code 26 , which also includes the year of manufacture,
is printed into the housing.
Example:
2018 XX XX
Year of Manufacture
Description (Fig. A)
WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
1 On/off switch
2 Motor unit
3 Depth adjustment ring
4 Micro adjustment scale
5 Groove pins
6 Spindle lock button
7 LED lights
8 Spindle
9 Collet
10 Collet nut
11 Cutter bit (not included)
12 Base
13 Sub-base
14 Sub-base screws
15 Quick release tabs
16 Locking lever
17 Locking lever adjustment screw
18 Guide slot
19 Straight edge guide
20 Roller bearing guide
21 Guide screw
22 Cutter bit shaft
23 Dust extraction adaptor
24 Finger screws
25 Dust exhaust port
Intended Use
Your DeWALT DWE6005 Laminate Trimmer is a small base highprecision power tool designed for professional trimming of
wood and plastic laminates.
DO NOT use under wet conditions or in the presence of
flammable liquids or gases.
This laminate trimmer is a professional power tool.
DO NOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
• Young children and the infirm. This appliance is not
intended for use by young children or infirm persons
without supervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
Inserting the Motor into the Base (Fig. A, C)
1. Open the locking lever 16 on the base.
2. If the depth adjustment ring 3 is not on the motor, thread
the ring 3 onto the motor until the ring is about halfway
between the top and bottom of the motor. Insert the
motor into the base by aligning the groove in the back of
the motor unit with the groove pins 5 on the base. Slide
the motor down until the depth adjustment ring snaps
into place.
3. Adjust the depth of cut by turning the depth adjustment
ring. Refer to Depth of Cut Adjusment.
4. Close the locking lever 16 when the desired depth is
achieved. For information on setting the cutting depth,
Refer to Depth of Cut Adjusment.
Locking Lever Adjustment (Fig. A)
Excessive force should not be used to clamp the locking lever
16 . Using excessive force may damage the base.
When the locking lever is clamped, the motor should not move
in the base.
Adjustment is needed if the locking lever will not clamp without
excessive force or if the motor moves in the base after clamping.
Adjusting the Locking Lever’s Clamping Force
1. Open the locking lever 16 .
2. Using a 2 mm hex wrench turn locking lever adjustment
screw 17 in small increments. Turning the screw clockwise
tightens the lever, while turning the screw counterclockwise
loosens the lever.
Motor Quick Release (Fig. D)
1. Open the locking lever 16 on the base.
2. Grasp the motor unit with one hand, depressing both quick
release tabs 15 .
3. With the other hand, grasp the base and pull motor from
the base.
7
English
Inserting and Removing a Cutter Bit
(Fig. A, E)
NOTE: Bits are not included but are available as an accessory.
1. Separate the motor unit 2 from the base.
2. Hold the motor unit 2 while pressing the spindle lock
button 6 .
3. Insert the cutter shaft 22 in the collet 9 .
4. Tighten the collet nut 10 using the 17 mm wrench.
5. To remove the cutter, hold the motor shaft while pressing
the spindle lock 6 .
6. Using the 17 mm wrench, loosen the collet nut 10 a few
turns and remove the cutter.
Replacing the Collet (Fig. A, E)
The laminate trimmer is supplied with an 6 mm collet fitted to
the tool. (GB / LX trimmers come with a 1/4" collet.)
1. Loosen the collet nut 10 completely.
2. Remove the collet 9 and replace it.
3. Tighten the collet nut 10 .
NOTE: Never tighten the collet nut 10 without first installing
a router bit in it. Tightening an empty collet nut, even by hand,
can damage the collet 9 .
Depth of Cut Adjustment (Fig. C, D)
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
1. Select and install the desired cutter. Refer to Inserting and
Removing a Cutter Bit.
2. Insert motor into base, ensuring base is attached to
the adjustment ring 3 . Place laminate trimmer on the
work piece.
3. Open the locking lever 16 and turn the depth adjustment
ring 3 until the cutter touches the work piece. Turning
the ring clockwise raises the cutter while turning it
counterclockwise lowers the cutting head.
4. Turn the micro adjustment scale 4 until the 0 on the scale
lines up with the pointer on the quick release tab 15 .
5. Turn the depth adjustment ring until the pointer lines
up with the desired depth of cut marked on the micro
adjustment scale. NOTE: Each mark on the adjustment scale
represents a depth change of 0.5 mm.
6. Close the locking lever 16 to lock the base.
Attaching the Dust Extraction Adaptor
(Fig. H)
The dust extraction adaptor 23 can be attached to the front of
the sub base underneath the locking lever as shown in Figure H.
Hand tighten both finger screws 24 and attach a vacumm hose
to the dust exhaust port 25 .
OPERATION
Instructions for Use
WARNING: Always observe the safety instructions and
applicable regulations.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
Proper Hand Position (Fig. G)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the motor base with
the other hand on the motor cap as shown.
Starting and Stopping the Motor (Fig. A, B)
To turn unit on, pull the on/off switch 1 up. To turn the unit off,
depress the switch back down into the motor housing. Refer to
Figure B.
Using an Edge Guide (Fig. A)
An edge guide is included with your laminate trimmer for use
with non-piloted bits on curved or straight applications.
1. Remove the screw 21 in the back of the fixed base.
2. Slide edge guide into edge guide slot 18 on back of fixed
base. Tighten hardware.
NOTE: To remove the edge guide, reverse the above procedure.
After removing edge guide, always replace the screw 21 into
the storage hole on the back of the base to prevent it from
being lost.
Direction of Feed (Fig. F)
The direction of feed is very important when trimming and
can make the difference between a successful job and a ruined
project. Figure F shows the proper direction of feed for some
typical cuts.
MAINTENANCE
Your DeWALT power tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
Lubrication
Your power tool requires no additional lubrication.
8
English
Cleaning
WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.
WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
Optional Accessories
WARNING: Since accessories, other than those offered
by DeWALT, have not been tested with this product, use
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only DeWALT recommended
accessories should be used with this product.
Consult your dealer for further information on the
appropriate accessories.
Protecting the Environment
Separate collection. Products and batteries marked
with this symbol must not be disposed of with normal
household waste.
Products and batteries contain materials that can
be recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and batteries
according to local provisions. Further information is available at
www.2helpU.com.
9
Belgique et
Luxembourg België en Luxemburg
DeWALT - Belgium BVBA
Egide Walschaertsstraat 16
2800 Mechelen
Tel: NL 32 15 47 37 63
Tel: FR 32 15 47 37 64
Fax:
32 15 47 37 99
www.dewalt.be
enduser.BE@SBDinc.com
Danmark
DeWALT (Stanley Black&Decker AS)
Roskildevej 22
2620 Albertslund
Tel:
Fax:
www.dewalt.dk
kundeservice.dk@sbdinc.com
Deutschland
DeWALT
Richard Klinger Str. 11
65510 Idstein
Tel:06126-21-0
Fax:06126-21-2770
www.dewalt.de
infodwge@sbdinc.com
Ελλάς
DeWALT (Ελλάς) Α.Ε.
EΔΡΑ-ΓΡΑΦΕΙΑ : Στράβωνος 7
& Λ. Βουλιαγμένης, Γλυφάδα 166 74, Αθήνα
SERVICE : Ημερος Τόπος 2 (Χάνι Αδάμ) – 193 00 Ασπρόπυργος
Τηλ:00302108981616
Φαξ:00302108983570
www.dewalt.gr
Greece.Service@sbdinc.com
España
DeWALT Ibérica, S.C.A.
Parc de Negocios “Mas Blau”
Edificio Muntadas, c/Bergadá, 1, Of. A6
08820 El Prat de Llobregat (Barcelona)
Tel:
Fax:
934 797 400
934 797 419
www.dewalt.es
respuesta.postventa@sbdinc.com
France
DeWALT
5, allée des Hêtres
BP 60105, 69579 Limonest Cedex
Tel:
Fax:
04 72 20 39 20
04 72 20 39 00
www.dewalt.fr
scufr@sbdinc.com
Schweiz
Suisse
Svizzera
DeWALT
In der Luberzen 42
8902 Urdorf
Tel:
Fax:
044 - 755 60 70
044 - 730 70 67
www.dewalt.ch
service@rofoag.ch
Ireland
DeWALT
Building 4500, Kinsale Road
Cork Airport Business Park
Cork, Ireland
Tel:00353-2781800
Fax:
01278 1811
www.dewalt.ie
Sales.ireland@sbdinc.com
Italia
DeWALT
via Energypark 6
20871 Vimercate (MB), IT
Tel: Fax: 800-014353
39 039-9590200
39 039-9590311
www.dewalt.it
Nederlands
DeWALT
Netherlands BVPostbus 83,
6120 AB BORN
Tel:
Fax:
31 164 283 063
31 164 283 200
www.dewalt.nl
Norge
DeWALT
Postboks 4613
0405 Oslo, Norge
Tel: Fax: 45 25 13 00
45 25 08 00
www.dewalt.no
kundeservice.no@sbdinc.com
Österreich
DeWALT
Werkzeug Vertriebsges m.b.H
Oberlaaerstrasse 248, A-1230 Wien
Tel: Fax: 01 - 66116 - 0
01 - 66116 - 614
www.dewalt.at
service.austria@sbdinc.com
Portugal
DeWALT
Ed. D Dinis, Quina da Fonte
Rua dos Malhoes 2 2A 2º Esq.
Oeiras e S. Juliao da Barra, paço de Arcos e Caxias
2770 071 Paço de Arcos
Tel: Fax: +351 214667500
+351214667580
www.dewalt.pt
resposta.posvenda@sbdinc.com
Suomi
DeWALT
PL47
00521 Helsinki, Suomi
Puh: Faksi:
010 400 4333
0800 411 340
www.dewalt.fi
asiakaspalvelu.fi@sbdinc.com
Sverige
DeWALT
BOX 94
43122 Mölndal
Sverige
Tel:
Fax: 031 68 61 60
031 68 60 08
www.dewalt.se
kundservice.se@sbdinc.com
Türkiye
Sanayi ve Ticareet Bakanlığı tebliğince kullanim ömrü 7 yıldır.
Stanley Black & Decker Turkey Alet Üretim San. Tic. Ltd.Şti.
Kozyataği Mh Değirmen Sk.
Nida Kule No: 18 Kat: 6, 34742
Kadıköy, İstanbul, Türkiye
Tel: Faks:
+90 216 665 2900
+90 216 665 2901
www.dewalt.com.tr
info-tr@sbdinc.com
United
Kingdom
DeWALT, 210 Bath Road;
Slough, Berks SL1 3YD
Tel: Fax: 01753-567055
01753-572112
www.dewalt.co.uk
emeaservice@sbdinc.com
Australia
DeWALT
810 Whitehorse Road Box Hill
VIC 3103 Australia
Tel: Aust 1800 338 002
Tel: NZ 0800 339 258
www.dewalt.com.au
www.dewalt.co.nz
Middle East Africa
DeWALT
P.O. Box - 17164,
Jebel Ali Free Zone (South), Dubai, UAE
Tel: Fax: www.dewalt.ae
Service.MEA@sbdinc.com
N597527
10
70 20 15 10
70 22 49 10
971 4 812 7400
971 4 2822765
3/18
Download PDF