DCH363 | DeWalt DCH363 ROTARY HAMMER instruction manual

DCH363
DCH364
Dansk (oversat fra original brugsvejledning)
4
Deutsch (übersetzt von den Originalanweisungen)
19
English (original instructions)
34
Español (traducido de las instrucciones originales)
47
Français (traduction de la notice d’instructions originale)
63
Italiano (tradotto dalle istruzioni originali)
77
Nederlands (vertaald vanuit de originele instructies)
92
Norsk (oversatt fra de originale instruksjonene)
107
Português (traduzido das instruções originais)
121
Suomi (käännetty alkuperäisestä käyttöohjeesta)
137
Svenska (översatt från de ursprungliga instruktionerna)
150
Türkçe (orijinal talimatlardan çevrilmiştir)
164
Ελληνικά (μετάφραση από τις πρωτότυπες οδηγίες)
179
Copyright DEWALT
2
2
1
8
7
3
4
10
20
5
11
9
2
1
6 8
3
4
10
7
5
11
9
12
11
21
13
14
A
1
18
17
19
A1
3
4
B
C
15
7
5
9
D
2
E
2
8
9
F
G
5
6
16
H
I
3
ENGLISH
CORDLESS ROTARY HAMMERDRILL
DCH363, DCH364
Congratulations!
You have chosen a DEWALT tool. Years of experience, thorough product development and innovation make
DEWALT one of the most reliable partners for professional power tool users.
Technical Data
Voltage
Type
No-load speed
Power output
Impact energy (EPTA 05/2009)
Maximum drilling range in
steel/wood/concrete
Tool holder
Impacts per minute
Weight (without battery pack)
LPA
KPA
LWA
KWA
(sound pressure)
(sound pressure uncertainty)
(sound power)
(sound power uncertainty)
DCH363
36
1
0–1100
600
2.3
DCH364
36
1
0–1100
600
2.3
kg
13/30/26
SDS Plus®
4500
2.6
13/30/26
SDS Plus®
4500
2.8
dB(A)
dB(A)
dB(A)
dB(A)
86
3
97
3
86
3
97
3
V
min-1
W
J
mm
Vibration total values (triax vector sum) determined according to EN 60745:
Vibration emission value ah
Drilling into metal
ah,D =
Uncertainty K =
m/s²
m/s²
<2.5
1.5
<2.5
1.5
Vibration emission value ah
Drilling into concrete
ah,HD =
Uncertainty K =
m/s²
m/s²
7.1
1.5
7.1
1.5
Vibration emission value ah
Chiselling
ah,Cheq =
Uncertainty K =
m/s²
m/s²
5.5
1.5
5.5
1.5
Vibration emission value ah
Screwdriving without impact
ah =
Uncertainty K =
m/s²
m/s²
<2.5
1.5
<2.5
1.5
The vibration emission level given in this information sheet has been measured in accordance with a
standardised test given in EN 60745 and may be used to compare one tool with another. It may be used for a
preliminary assessment of exposure.
4
ENGLISH
WARNING: The declared vibration
emission level represents the main
applications of the tool. However if the
tool is used for different applications,
with different accessories or poorly
maintained, the vibration emission may
differ. This may significantly increase the
exposure level over the total working
period.
An estimation of the level of exposure to
vibration should also take into account
the times when the tool is switched off or
when it is running but not actually doing
the job. This may significantly reduce
the exposure level over the total working
period.
Identify additional safety measures to
protect the operator from the effects of
vibration such as: maintain the tool and
the accessories, keep the hands warm,
organisation of work patterns.
Battery pack
DE9360/DC9360
DCB360 DCB361
Voltage
VDC
36
36
36
Capacity
Ah
2.0
4.0
2.0
Weight
kg
0.9
1.3
0.9
Charger
NOTICE: indicates a practice not
related to personal injury which, if
not avoided, may result in property
damage.
Denotes risk of electric shock.
Denotes risk of risk of fire.
EC-Declaration of Conformity
MACHINERY DIRECTIVE
CORDLESS ROTARY HAMMERDRILL
DCH363, DCH364
DEWALT declares that these products described
under Technical Data are in compliance with:
2006/42/EC, EN 60745-1, EN 60745-2-6.
These products also comply with Directive
2014/30/EU and 2011/65/EU. For more information,
please contact DEWALT at the following address or
refer to the back of the manual.
The undersigned is responsible for compilation of the
technical file and makes this declaration on behalf of
DEWALT.
DE9000/DC9000
Mains voltage
VAC
Approx. charging time
min
Weight
kg
230
90
(4.0 Ah)
45
(2.0 Ah)
0.9
Fuses:
Europe
230 V tools 10 Amperes, mains
U.K. & Ireland
230 V tools 3 Amperes, in plugs
Definitions: Safety Guidelines
The definitions below describe the level of severity for
each signal word. Please read the manual and pay
attention to these symbols.
DANGER: Indicates an imminently
hazardous situation which, if not avoided,
will result in death or serious injury.
WARNING: Indicates a potentially
hazardous situation which, if not avoided,
could result in death or serious injury.
CAUTION: Indicates a potentially
hazardous situation which, if not avoided,
may result in minor or moderate
injury.
Horst Grossmann
Vice President Engineering
DEWALT, Richard-Klinger-Straße 11,
D-65510, Idstein, Germany
30.01.2014
WARNING: To reduce the risk of injury,
read the instruction manual.
General Power Tool Safety Warnings
WARNING! Read all safety warnings
and all instructions. Failure to follow the
warnings and instructions may result in
electric shock, fire and/or serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or batteryoperated (cordless) power tool.
5
ENGLISH
1) WORK AREA SAFETY
a) Keep work area clean and well lit. Cluttered
or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power
tools create sparks which may ignite the dust
or fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can
cause you to lose control.
2) ELECTRICAL SAFETY
a) Power tool plugs must match the outlet.
Never modify the plug in any way. Do
not use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of electric
shock.
b) Avoid body contact with earthed or
grounded surfaces such as pipes,
radiators, ranges and refrigerators. There is
an increased risk of electric shock if your body
is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord
for carrying, pulling or unplugging the
power tool. Keep cord away from heat, oil,
sharp edges or moving parts. Damaged or
entangled cords increase the risk of electric
shock.
e) When operating a power tool outdoors, use
an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces
the risk of electric shock.
f) If operating a power tool in a damp
location is unavoidable, use a residual
current device (RCD) protected supply. Use
of an RCD reduces the risk of electric shock.
3) PERSONAL SAFETY
a) Stay alert, watch what you are doing and
use common sense when operating a
power tool. Do not use a power tool while
you are tired or under the influence of
drugs, alcohol or medication. A moment of
inattention while operating power tools may
result in serious personal injury.
b) Use personal protective equipment. Always
wear eye protection. Protective equipment
such as dust mask, non-skid safety shoes,
hard hat, or hearing protection used for
appropriate conditions will reduce personal
injuries.
c) Prevent unintentional starting. Ensure
the switch is in the off position before
6
d)
e)
f)
g)
connecting to power source and/or battery
pack, picking up or carrying the tool.
Carrying power tools with your finger on the
switch or energising power tools that have the
switch on invites accidents.
Remove any adjusting key or wrench
before turning the power tool on. A wrench
or a key left attached to a rotating part of the
power tool may result in personal injury.
Do not overreach. Keep proper footing
and balance at all times. This enables
better control of the power tool in unexpected
situations.
Dress properly. Do not wear loose clothing
or jewellery. Keep your hair, clothing and
gloves away from moving parts. Loose
clothes, jewellery or long hair can be caught in
moving parts.
If devices are provided for the connection
of dust extraction and collection facilities,
ensure these are connected and properly
used. Use of dust collection can reduce dustrelated hazards.
4) POWER TOOL USE AND CARE
a) Do not force the power tool. Use the
correct power tool for your application. The
correct power tool will do the job
better and safer at the rate for which it
was designed.
b) Do not use the power tool if the switch
does not turn it on and off. Any power
tool that cannot be controlled with the switch
is dangerous and must be repaired.
c) Disconnect the plug from the power source
and/or the battery pack from the power
tool before making any adjustments,
changing accessories, or storing power
tools. Such preventive safety measures
reduce the risk of starting the power tool
accidentally.
d) Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands of
untrained users.
e) Maintain power tools. Check for
misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tool’s operation.
If damaged, have the power tool repaired
before use. Many accidents are caused by
poorly maintained power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are
easier to control.
ENGLISH
g)
Use the power tool, accessories and
tool bits etc., in accordance with these
instructions taking into account the working
conditions and the work to be performed.
Use of the power tool for operations different
from those intended could result in a
hazardous situation.
5) BATTERY TOOL USE AND CARE
a) Recharge only with the charger specified
by the manufacturer. A charger that is
suitable for one type of battery pack may
create a risk of fire when used with another
battery pack.
b) Use power tools only with specifically
designated battery packs. Use of any
other battery packs may create a risk of
injury and fire.
c) When battery pack is not in use, keep it
away from other metal objects like paper
clips, coins, keys, nails, screws or other
small metal objects that can make a
connection from one terminal to another.
Shorting the battery terminals together may
cause burns or a fire.
d) Under abusive conditions, liquid may be
ejected from the battery; avoid contact.
If contact accidentally occurs, flush with
water. If liquid contacts eyes, additionally
seek medical help. Liquid ejected from the
battery may cause irritation or burns.
6) SERVICE
a) Have your power tool serviced by a
qualified repair person using only identical
replacement parts. This will ensure that the
safety of the power tool is maintained.
Additional Specific Safety Rules for
Rotary Hammers
• Wear ear protectors. Exposure to noise can
cause hearing loss.
• Use auxiliary handle(s) if supplied with the
tool. Loss of control can cause personal injury.
• Wear safety goggles or other eye protection.
Hammering operations cause chips to fly. Flying
particles can cause permanent eye damage.
Wear a dust mask or respirator for applications
that generate dust. Ear protection may be
required for most applications.
• Keep a firm grip on the tool at all times.
Do not attempt to operate this tool without
holding it with both hands. It is recommended
that the side handle be used at all times.
Operating this tool with one hand will result in
loss of control. Breaking through or encountering
hard materials such as re-bar may be hazardous
as well. Tighten the side handle securely before
use.
• Do not operate this tool for long periods of
time. Vibration caused by hammer action may
be harmful to your hands and arms. Use gloves
to provide extra cushion and limit exposure by
taking frequent rest periods.
• Do not recondition bits yourself. Chisel
reconditioning should be done by an authorized
specialist. Improperly reconditioned chisels could
cause injury.
• Wear gloves when operating tool or changing
bits. Accessible metal parts on the tool and bits
may get extremely hot during operation. Small
bits of broken material may damage bare hands.
• Never lay the tool down until the bit has come
to a complete stop. Moving bits could cause
injury.
• Do not strike jammed bits with a hammer to
dislodge them. Fragments of metal or material
chips could dislodge and cause injury.
• Slightly worn chisels can be resharpened by
grinding.
• Keep the power cord away from the rotating
bit. Do not wrap the cord around any part of
your body. An electric cord wrapped around a
spinning bit may cause personal injury and loss
of control.
• Hold the power tool by insulated gripping
surfaces when performing an operation where
the cutting accessory may contact hidden
wiring. Cutting accessory contacting a “live” wire
will make exposed metal parts of the tool “live”
and could give the operator an electric shock.
Residual Risks
• Use clamps or other practical way to secure
and support the workpiece to a stable
platform. Holding the work by hand or against
your body is unstable and may lead to loss of
control.
In spite of the application of the relevant safety
regulations and the implementation of safety devices,
certain residual risks cannot be avoided. These are:
The following risks are inherent to the use of rotary
hammers:
- Injuries caused by touching the rotating parts or
hot parts of the tool.
- Impairment of hearing.
- Risk of squeezing fingers when changing the
accessory.
7
ENGLISH
- Health hazards caused by breathing dust
developed when working in concrete and/or
masonry.
Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual before use.
Wear ear protection.
Wear eye protection.
DATE CODE POSITION (FIG. A)
The Date Code (20) which also includes the year of
manufacture, is printed into the housing surface that
forms the mounting joint between tool and battery.
Example:
2014 XX XX
Year of Manufacture
Important Safety Instructions for All
Battery Chargers
SAVE THESE INSTRUCTIONS: This manual
contains important safety and operating instructions
for the DE9000/DC9000 battery charger.
• Before using charger, read all instructions and
cautionary markings on charger, battery pack,
and product using battery pack.
DANGER: Electrocution hazard.
230 volts are present at charging
terminals. Do not probe with conductive
objects. Electric shock or electrocution
may result.
WARNING: Shock hazard. Do not allow
any liquid to get inside charger. Electric
shock may result.
CAUTION: Burn hazard. To reduce
the risk of injury, charge only DEWALT
rechargeable batteries. Other types of
batteries may burst causing personal
injury and damage.
CAUTION: Under certain conditions,
with the charger plugged in to the power
supply, the exposed charging contacts
inside the charger can be shorted by
foreign material. Foreign materials of
a conductive nature such as, but not
limited to, steel wool, aluminum foil, or
8
any buildup of metallic particles should
be kept away from charger cavities.
Always unplug the charger from the
power supply when there is no battery
pack in the cavity. Unplug charger before
attempting to clean.
• DO NOT attempt to charge the battery pack
with any chargers other than the ones in
this manual. The charger and battery pack are
specifically designed to work together.
• These chargers are not intended for any uses
other than charging DEWALT rechargeable
batteries. Any other uses may result in risk of
fire, electric shock or electrocution.
• Do not expose charger to rain or snow.
• Pull by plug rather than cord when
disconnecting charger. This will reduce risk
of damage to electric plug and cord.
• Make sure that cord is located so that it will
not be stepped on, tripped over, or otherwise
subjected to damage or stress.
• Do not use an extension cord unless it
is absolutely necessary. Use of improper
extension cord could result in risk of fire,
electric shock, or electrocution.
• Do not place any object on top of charger
or place the charger on a soft surface that
might block the ventilation slots and result in
excessive internal heat. Place the charger in a
position away from any heat source. The charger
is ventilated through slots in the top and the
bottom of the housing.
• Do not operate charger with damaged cord
or plug — have them replaced immediately.
• Do not operate charger if it has received
a sharp blow, been dropped, or otherwise
damaged in any way. Take it to an authorised
service center.
• Do not disassemble charger; take it to an
authorized service center when service or
repair is required. Incorrect reassembly may
result in a risk of electric shock, electrocution or
fire.
• Disconnect the charger from the outlet before
attempting any cleaning. This will reduce the
risk of electric shock. Removing the battery
pack will not reduce this risk.
• NEVER attempt to connect 2 chargers together.
• The charger is designed to operate on
standard 230 V household electrical power.
Do not attempt to use it on any other voltage.
This does not apply to the vehicular charger.
ENGLISH
SAVE THESE INSTRUCTIONS
Chargers
LI-ION BATTERY PACKS ONLY
The DE9000/DC9000 chargers accept 36 V Li-Ion
batteries only.
This charger requires no adjustment and is designed
to be as easy as possible to operate.
Charging Procedure (fig. A, B)
DANGER: Electrocution hazard.
230 volts present at charging terminals.
Do not probe with conductive objects.
Danger of electric shock or electrocution.
1. Plug the charger (13) into an appropriate outlet
before inserting battery pack.
2. Insert the battery pack into the charger. The
charger is equipped with a three-light fuel gauge
that will blink according to the state of charge of
the battery pack.
3. The completion of charge will be indicated by the
red light remaining ON continuously. The pack is
fully charged and may be used at this time or left
in the charger.
NOTE: To ensure maximum performance and life of
Li-Ion batteries, charge the battery pack fully before
first use.
Charging Process
Refer the table below for the state of charge of the
battery pack.
State of charge
1 light blinking
1 light blinking, 1 light on
1 light blinking, 2 lights on
3 lights on
then automatically switches to the pack charging
mode. This feature ensures maximum battery life.
< 33%
33–66%
66–99%
100%
Automatic Refresh
The automatic refresh mode will equalise or balance
the individual cells in the battery pack at its peak
capacity. Battery packs should be refreshed weekly
or whenever the pack no longer delivers the same
amount of work.
To refresh your battery pack, place the battery in the
charger as usual. Leave the battery pack for at least
10 hours in the charger.
Hot/Cold Pack Delay
When the charger detects a battery that is too hot
or too cold, it automatically starts a Hot/Cold Pack
Delay, suspending charging until the battery has
reached an appropriate temperature. The charger
Li-Ion batteries are designed with an Electronic
Protection System that will protect the battery against
overloading, overheating or deep discharge.
The tool will automatically turn off if the Electronic
Protection System engages. If this occurs, place the
Li-Ion battery on the charger until it is fully charged.
Important Safety Instructions for All
Battery Packs
When ordering replacement battery packs, be sure to
include catalogue number, voltage and amp hour.
The battery pack is not fully charged out of the
carton. Before using the battery pack and charger,
read the safety instructions below. Then follow
charging procedures outlined.
READ ALL INSTRUCTIONS
• Do not charge or use battery in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Inserting or
removing the battery from the charger may ignite
the dust or fumes.
• Charge the battery packs only in DEWALT
chargers.
• DO NOT splash or immerse in water or other
liquids.
• Do not store or use the tool and battery pack
in locations where the temperature may reach
or exceed 40 ˚C (such as outside sheds or
metal buildings in summer).
DANGER: Never attempt to open the
battery pack for any reason. If battery
pack case is cracked or damaged, do not
insert into charger. Do not crush, drop
or damage battery pack. Do not use a
battery pack or charger that has received
a sharp blow, been dropped, run over or
damaged in any way (i.e., pierced with
a nail, hit with a hammer, stepped on).
Electric shock or electrocution may result.
Damaged battery packs should be
returned to service center for recycling.
CAUTION: When not in use, place
tool on its side on a stable surface
where it will not cause a tripping or
falling hazard. Some tools with large
battery packs will stand upright on the
battery pack but may be easily knocked
over.
9
ENGLISH
SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM ION
(Li Ion)
• Do not incinerate the battery pack even if it
is severely damaged or is completely worn
out. The battery pack can explode in a fire. Toxic
fumes and materials are created when lithium ion
battery packs are burned.
• If battery contents come into contact with the
skin, immediately wash area with mild soap
and water. If battery liquid gets into the eye, rinse
water over the open eye for 15 minutes or until
irritation ceases. If medical attention is needed,
the battery electrolyte is composed of a mixture
of liquid organic carbonates and lithium salts.
• Contents of opened battery cells may cause
respiratory irritation. Provide fresh air. If
symptoms persists, seek medical attention.
WARNING: Burn hazard. Battery liquid
may be flammable if exposed to spark or
flame.
Transportation
DEWALT batteries comply with all applicable shipping
regulations as prescribed by industry and legal
standards which include UN Recommendations on
the Transport of Dangerous Goods; International
Air Transport Association (IATA) Dangerous Goods
Regulations, International Maritime Dangerous Goods
(IMDG) Regulations, and the European Agreement
Concerning The International Carriage of Dangerous
Goods by Road (ADR). Lithium-ion cells and
batteries have been tested to section 38.3 of the UN
Recommendations on the Transport of Dangerous
Goods Manual of Tests and Criteria.
In most instances, shipping a DEWALT battery pack
will be excepted from being classified as a fully
regulated Class 9 Hazardous material. In general, the
two instances that require shipping Class 9 are:
1. Air shipping more than two DEWALT lithium-ion
battery packs when the package contains only
battery packs (no tools), and
2. Any shipment containing a lithium-ion battery
with an energy rating greater than 100 watt hours
(Wh). All lithium-ion batteries have the watt hour
rating marked on the pack.
Regardless of whether a shipment is considered
excepted or fully regulated, it is the shipper's
responsibility to consult the latest regulations for
packaging, labeling/marking and documentation
requirements.
Transporting batteries can possibly cause fire if the
battery terminals inadvertently come in contact with
conductive materials. When transporting batteries,
make sure that the battery terminals are protected
10
and well insulated from materials that could contact
them and cause a short circuit.
The information provided in this section of the manual
is provided in good faith and believed to be accurate
at the time the document was created. However,
no warranty, expressed or implied, is given. It is
the buyer’s responsibility to ensure that its activities
comply with the applicable regulations.
Battery Pack
BATTERY TYPE
The DCH363 and DCH364 operate on 36 volt Li-Ion
battery packs.
Storage Recommendations
1. The best storage place is one that is cool and
dry away from direct sunlight and excess heat or
cold. For optimum battery performance and life,
store battery packs at room temperature when
not in use.
NOTE: Li-Ion battery packs should be fully
charged when stored.
2. Long storage will not harm the battery pack or
charger. Under proper conditions, they can be
stored for up to 5 years.
Labels on Charger and Battery Pack
In addition to the pictographs used in this manual, the
labels on the charger and the battery pack show the
following pictographs:
Read instruction manual before use.
See Technical Data for charging time
Do not expose to water
Do not probe with conductive objects
Do not charge damaged battery packs
Do not use damaged chargers
Charge only between 4 °C and 40 °C
ENGLISH
Have defective cords replaced immediately
6 Locking collar
7 Dust cover
8 Depth adjustment rod
Charger problem
9 Side handle
10 Main handle
Battery problem
11 Battery pack
12 Release button
Discard the battery pack with due care for
the environment
13 Charger
14 Charging indicators (red)
15 Tool holder locking sleeve
Do not incinerate the battery pack
16 Keyless chuck
INTENDED USE
Charge DEWALT battery packs only with
designated DEWALT chargers. Charging
battery packs other than the designated
DEWALT batteries with a DEWALT charger
may make them burst or lead to other
dangerous situations.
Package Contents
The package contains:
1 Cordless rotary hammerdrill
1 Side handle
1 Depth adjustment rod
1 Keyless chuck (DCH364)
2 Battery packs (D2, M2)
1 Battery pack (D1, M1)
1 Charger
1 Kitbox
1 Instruction manual
Your cordless rotary hammerdrills have been
designed for professional drilling, hammerdrilling and
screwdriving applications as well as for light chipping.
DO NOT use under wet conditions or in presence of
flammable liquids or gases.
These heavy-duty rotary hammerdrills are professional
power tools. DO NOT let children come into
contact with the tool. Supervision is required when
inexperienced operators use this tool.
• Young children and the infirm. This appliance
is not intended for use by young children or infirm
persons without supervision.
• This product is not intended for use by persons
(including children) suffering from diminished
physical, sensory or mental abilities; lack of
experience, knowledge or skills unless they are
supervised by a person responsible for their
safety. Children should never be left alone with
this product.
DUST EXTRACTION SYSTEM (FIG. A1)
NOTE: Battery packs and chargers are not included
with N-models.
17 Electrical pins for dust extraction system
• Check for damage to the tool, parts or
accessories which may have occurred during
transport.
19 Dust extraction system attached to rotary
hammerdrill
• Take the time to thoroughly read and understand
this manual prior to operation.
*The dust extraction system (D25302DH) can be
purchased separately from your nearest authorised
DEWALT dealer at additional cost.
Description (fig. A, A1, D, H)
WARNING: Never modify the power tool
or any part of it. Damage or personal
injury could result.
1 Variable speed switch
18 Dust extraction system (D25302DH)*
OVERLOAD CLUTCH
In case of jamming of a drill bit, the drive to the drill
spindle is interrupted. Because of the resulting forces,
always hold the tool with both hands and take a firm
stance.
2 Forward/reverse slider
BRAKE MECHANISM
3 Mode selector
When the variable speed switch is released,
the spindle will stop rotating instantly.
4 Safety lock
5 SDS Plus® tool holder
11
ENGLISH
ACTIVE VIBRATION CONTROL
The active vibration control neutralises rebound
vibration from the hammer mechanism. Lowering
hand and arm vibration, it allows more comfortable
use for longer periods of time and extends the life of
the unit. In operation, a spring loaded mechanism
counterbalances the vibration forces. This can be
sensed by the cushioning effect when pressure is
applied to the tool. Make sure the spring is engaged
but not too firmly. The mechanism should be allowed
to "float."
Electrical Safety
The electric motor has been designed for one voltage
only. Always check that the battery pack voltage
corresponds to the voltage on the rating plate.
Also make sure that the voltage of your charger
corresponds to that of your mains.
Your DEWALT charger is double insulated
in accordance with EN 60335; therefore no
earth wire is required.
If the supply cord is damaged, it must be replaced
by a specially prepared cord available through the
DEWALT service organization.
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
• Safely dispose of the old plug.
• Connect the brown lead to the live terminal in the
plug.
• Connect the blue lead to the neutral terminal.
WARNING: No connection is to be made
to the earth terminal.
Follow the fitting instructions supplied with good
quality plugs. Recommended fuse: 3 A.
Using an Extension Cable
An extension cord should not be used unless
absolutely necessary. Use an approved extension
cable suitable for the power input of your charger
(see technical data). The minimum conductor size is
1 mm2; the maximum length is 30 m.
When using a cable reel, always unwind the cable
completely.
ASSEMBLY AND ADJUSTMENT
WARNING: Prior to assembly and
adjustment, always remove the
battery pack. Always switch off the
12
tool before inserting or removing the
battery pack.
WARNING: Use only DEWALT battery
packs and chargers.
Fitting and Removing the Battery
Pack (fig. A)
• To fit the battery pack (11), line it up with the
receptacle on the tool. Slide the battery pack into
the receptacle and push until the battery snaps
into place.
• To remove the battery pack, push the release
button (12) while at the same time pulling the
battery pack out of the receptacle.
FUEL GAUGE BATTERY PACKS (FIG. A)
Some DEWALT battery packs include a fuel gauge
which consists of three green LED lights that indicate
the level of charge remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel
gauge button (21). A combination of the three green
LED lights will illuminate designating the level of
charge left. When the level of charge in the battery
is below the usable limit, the fuel gauge will not
illuminate and the battery will need to be recharged.
NOTE: The fuel gauge is only an indication of the
charge left on the battery pack. It does not indicate
tool functionality and is subject to variation based
on product components, temperature and end-user
application.
Selecting the Operating Mode (fig. C)
The tool can be used in the following operating
modes:
Rotary drilling: for screwdriving and for
drilling into steel, wood and plastics
Hammer drilling: for concrete and
masonry drilling
Hammering only: for light chipping
• To select the operating mode, press the safety
lock (4) and rotate the mode selector switch (3)
until it points to the symbol of the required mode.
• Release the safety lock and check that the mode
selector switch is locked in place.
WARNING: Do not select the operating
mode when the tool is running.
ENGLISH
Inserting and Removing SDS Plus®
Accessories (fig. D)
Replacing the SDS Plus® Tool Holder
with the Keyless Chuck (fig. H)
Your rotary hammerdrill uses SDS Plus® accessories
(refer to the inset in fig. D for a cross-section of an
SDS Plus® bit shank).
DCH364
• Clean and grease the SDS Plus® bit shank.
• Insert the SDS Plus® bit shank into the SDS Plus®
tool holder (5).
• Push the bit down and turn it slightly until it fits
into the slots.
• Pull on the bit to check if it is properly locked.
The hammering function requires the bit to be
able to move axially several centimetres when
locked in the SDS Plus® tool holder.
•
To remove a bit, pull back the SDS Plus® tool
holder locking sleeve (15) and pull out the bit.
• Turn the locking collar (6) into the unlocked
position and pull the SDS Plus® tool holder (5) off.
• Push the keyless chuck (16) onto the spindle and
turn the locking collar into the locked position.
• To replace the keyless chuck with the SDS Plus®
tool holder, first remove the keyless chuck the
same way as the SDS Plus® tool holder was
removed. Then place the SDS Plus® tool holder
the same way as the keyless chuck was placed.
CAUTION: Never use the keyless chuck
(16) in the hammerdrilling mode. Only the
SDS Plus® toolholder should be used for
hammerdrilling.
Fitting the Side Handle (fig. E)
Replacing the Dust Cover (fig. D)
The side handle (9) can be fitted to suit both
right-hand and left-hand users.
The dust cover (7) prevents dust ingress into the
mechanism. Replace a worn dust cover immediately.
WARNING: Do not use the tool without
the side handle properly assembled.
• Pull back the SDS Plus® tool holder locking
sleeve (15) and pull the dust cover (7) off.
• Loosen the side handle.
• Fit the new dust cover.
• For RH-users, slide the side handle clamp over
the collar behind the tool holder, handle at the
left.
• Release the SDS Plus® tool holder locking sleeve.
• For LH-users, slide the side handle clamp over
the collar behind the tool holder, handle at the
right.
OPERATION
Instructions for Use
• Insert the required drill bit.
WARNING: To reduce the risk of
serious personal injury, turn tool
off and disconnect battery pack
before making any adjustments or
removing/installing attachments or
accessories. An accidental start-up can
cause injury.
• Slacken the side handle (9).
WARNING:
• Rotate the side handle to the desired position
and tighten the handle.
Setting the Drilling Depth (fig. F)
• Fit the depth adjustment rod (8) through the hole
in the side handle clamp.
• Adjust the drilling depth as shown.
• Always observe the safety instructions and
applicable regulations.
• Tighten the side handle.
• Be aware of the location of pipework and wiring.
• Push the forward/reverse slider (2) to the LH-side
for forward (RH) rotation. See arrows on tool.
• Apply only a gentle pressure to the tool (approx.
5 kg). Excessive force does not speed up drilling
but decreases tool performance and may shorten
tool life.
• Push the forward/reverse slider (2) to the RH-side
for reverse (LH) rotation.
• Do not drill or drive too deep to prevent damage
to the dust cover.
Forward/Reverse Slider (fig. G)
CAUTION: Always wait until the motor
has come to a complete standstill before
changing the direction of rotation.
• Always hold the tool firmly with both hands and
ensure a secure stance.
• Always operate the tool with the side handle
properly mounted.
13
ENGLISH
• If the cutting tool is no longer sharp, replace with
a new cutting tool.
Prior to Operation:
• Make sure your battery pack is (fully) charged.
• Make sure the battery pack is properly seated.
Proper Hand Position (fig. A, I)
WARNING: To reduce the risk of serious
personal injury, ALWAYS use proper
hand position as shown.
WARNING: To reduce the risk of serious
personal injury, ALWAYS hold securely in
anticipation of a sudden reaction.
Proper hand position requires one hand on the
side handle (9), with the other hand on the main
handle (10).
Switching On and Off (fig. A)
• To run the tool, press the variable speed switch
(1). The pressure exerted on the variable speed
switch determines the tool speed.
• To stop the tool, release the switch.
• To lock the tool in off position, move the forward/
reverse slider (2) to the central position.
Hammerdrilling (fig. A)
• Set the mode selector switch (3) to the
"hammerdrilling" position.
• Insert the appropriate drill bit. For best results use
high quality carbide-tipped bits.
• Adjust the side handle (9) as required.
• If necessary, set the drilling depth.
• Mark the spot where the hole is to be drilled.
• Place the drill bit on the spot and switch on the
tool.
Rotary Drilling (fig. A, H)
• Set the mode selector switch (3) to the "rotary
drilling" position.
• Depending on your tool, follow either of the
following instructions:
- Fit a chuck adaptor/chuck assembly (DCH363).
Keyed and keyless chucks and chuck adaptors
can be purchased separately. Special SDS
Plus® adaptors with threaded sections are
available for use with standard 10 or 13 mm
chucks to enable straight shank bits to be
used.
- Replace the SDS Plus® tool holder with the
keyless chuck (16) (DCH364).
14
• Proceed as described for hammerdrilling.
CAUTION: Never use the keyless chuck
(16) in the hammerdrilling mode. Only the
SDS Plus® toolholder should be used for
hammerdrilling.
Screwdriving (fig. A, H)
• Set the mode selector switch (3) to the "rotary
drilling" position.
• Select the direction of rotation.
• Depending on your tool, follow either of the
following instructions:
- Insert a special SDS Plus® screwdriving adaptor
for use with hexagonal screwdriver bits which
can be purchased separately (DCH363).
- Replace the SDS Plus® tool holder (5) with the
keyless chuck (16) (DCH364).
• Insert the appropriate screwdriver bit. When
driving slotted head screws, always use bits with
a finder sleeve.
• Gently press the variable speed switch (1) to
prevent damage to the screw head. In reverse
(LH) rotation the tool speed is automatically
reduced for easy screw removal.
• When the screw is flush with the workpiece,
release the variable speed switch to prevent the
screw head from penetrating into the workpiece.
Chipping (fig. A)
DCH363, DCH364
• Set the mode selector switch (3) to the
"hammering only" position.
• Insert the appropriate chisel and check if it is
properly locked.
• Adjust the side handle (9) as required.
• Switch on the tool and start working.
It may be necessary to briefly run the motor after
having changed from chiselling to rotary modes in
order to align the gears.
WARNING:
• Do not use this tool to mix or pump easily
combustible or explosive fluids (benzine, alcohol,
etc.).
• Do not mix or stir inflammable liquids labelled
accordingly.
MAINTENANCE
Your DEWALT power tool has been designed to
operate over a long period of time with a minimum
ENGLISH
of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
WARNING: To reduce the risk of
serious personal injury, turn tool
off and disconnect battery pack
before making any adjustments or
removing/installing attachments or
accessories. An accidental start-up can
cause injury.
The charger and battery pack are not serviceable.
There are no serviceable parts inside.
Lubrication
Your power tool requires no additional lubrication.
Accessories and attachments used must be regularly
lubricated around the SDS Plus® fitment.
Cleaning
WARNING: Blow dirt and dust out of the
main housing with dry air as often as dirt
is seen collecting in and around the air
vents. Wear approved eye protection and
approved dust mask when performing
this procedure.
WARNING: Never use solvents or other
harsh chemicals for cleaning the nonmetallic parts of the tool. These chemicals
may weaken the materials used in these
parts. Use a cloth dampened only with
water and mild soap. Never let any liquid
get inside the tool; never immerse any
part of the tool into a liquid.
Various types of SDS Plus® drill bits and chisels are
available as an option.
Consult your dealer for further information on the
appropriate accessories.
Protecting the Environment
Separate collection. This product must
not be disposed of with normal household
waste.
Should you find one day that your DEWALT product
needs replacement, or if it is of no further use to you,
do not dispose of it with household waste. Make this
product available for separate collection.
Separate collection of used products and
packaging allows materials to be
recycled and used again. Re-use of
recycled materials helps prevent
environmental pollution and reduces
the demand for raw materials.
Local regulations may provide for separate collection
of electrical products from the household, at municipal
waste sites or by the retailer when you purchase a
new product.
DEWALT provides a facility for the collection and
recycling of DEWALT products once they have
reached the end of their working life. To take
advantage of this service please return your product
to any authorised repair agent who will collect them
on our behalf.
You can check the location of your nearest authorised
repair agent by contacting your local DEWALT office
at the address indicated in this manual. Alternatively, a
list of authorised DEWALT repair agents and full details
of our after-sales service and contacts are available
on the Internet at: www.2helpU.com.
CHARGER CLEANING INSTRUCTIONS
WARNING: Shock hazard. Disconnect
the charger from the AC outlet before
cleaning. Dirt and grease may be
removed from the exterior of the charger
using a cloth or soft non-metallic brush.
Do not use water or any cleaning
solutions.
Optional Accessories
WARNING: Since accessories, other
than those offered by DEWALT, have not
been tested with this product, use of
such accessories with this tool could be
hazardous. To reduce the risk of injury,
only DEWALT recommended accessories
should be used with this product.
Battery Pack
The long life battery pack must be recharged when it
fails to produce sufficient power on jobs which were
easily done before. At the end of its technical life,
discard it with due care for our environment:
• Run the battery pack down completely, then
remove it from the tool.
• Li-Ion cells are recyclable. Take them to your
dealer or a local recycling station. The collected
battery packs will be recycled or disposed of
properly.
15
ENGLISH
GUARANTEE
DEWALT is confident of the quality of its
products and offers an outstanding guarantee
for professional users of the product. This
guarantee statement is in addition to and in
no way prejudices your contractual rights as a
professional user or your statutory rights as a
private non-professional user. The guarantee
is valid within the territories of the Member
States of the European Union and the
European Free Trade Area.
• 30 DAY NO RISK SATISFACTION GUARANTEE •
If you are not completely satisfied with the
performance of your DEWALT tool, simply
return it within 30 days, complete with all
original components, as purchased, to
the point of purchase, for a full refund or
exchange. The product must have been
subject to fair wear and tear and proof of
purchase must be produced.
• ONE YEAR FREE SERVICE CONTRACT •
If you need maintenance or service for your
DEWALT tool, in the 12 months following
purchase, you are entitled to one service free
of charge. It will be undertaken free of charge
at an authorised DEWALT repair agent. Proof
of purchase must be produced. Includes
labour. Excludes accessories and spare parts
unless failed under warranty.
• ONE YEAR FULL WARRANTY •
If your DEWALT product becomes defective
due to faulty materials or workmanship
within 12 months from the date of purchase,
DEWALT guarantees to replace all defective
parts free of charge or – at our discretion –
replace the unit free of charge provided that:
• The product has not been misused;
• The product has been subject to fair
wear and tear;
• Repairs have not been attempted by
unauthorised persons;
• Proof of purchase is produced;
• The product is returned complete with all
original components.
If you wish to make a claim, contact your
seller or check the location of your nearest
authorised DEWALT repair agent in the
DEWALT catalogue or contact your DEWALT
office at the address indicated in this manual.
A list of authorised DEWALT repair agents and
full details of our after-sales service is available
on the Internet at: www.2helpU.com.
16
17
Belgique et
DEWALT - Belgium BVBA
Luxembourg België Egide Walschaertsstraat 16
en Luxemburg
2800 Mechelen
Tel: NL
Tel: FR
Fax:
Danmark
DEWALT
Roskildevej 22
2620 Albertslund
Tel: 70 20 15 11
Fax: 70 22 49 10
www.dewalt.dk
kundeservice.dk@sbdinc.com
Deutschland
DEWALT
Richard Klinger Str. 11
65510 Idstein
Tel: 06126-21-1
Fax: 06126-21-2770
www.dewalt.de
infobfge@sbdinc.com
Ελλάς
DEWALT (Ελλάς) Α.Ε.
Τηλ: 00302108981616
EΔΡΑ-ΓΡΑΦΕΙΑ : Στράβωνος 7
Φαξ: 00302108983570
& Λ. Βουλιαγμένης, Γλυφάδα 166 74, Αθήνα
SERVICE : Ημερος Τόπος 2 (Χάνι Αδάμ) –
193 00 Ασπρόπυργος
www.dewalt.gr
Greece.Service@sbdinc.com
España
DEWALT Ibérica, S.C.A.
Parc de Negocios “Mas Blau”
Edificio Muntadas, c/Bergadá, 1, Of. A6
08820 El Prat de Llobregat (Barcelona)
Tel: 934 797 400
Fax: 934 797 419
www.dewalt.es
respuesta.postventa@sbdinc.com
France
DEWALT
5, allée des Hêtres
BP 30084, 69579 Limonest Cedex
Tel: 04 72 20 39 20
Fax: 04 72 20 39 00
www.dewalt.fr
scufr@sbdinc.com
Schweiz
Suisse
Svizzera
DEWALT
In der Luberzen 42
8902 Urdorf
Tel: 044 - 755 60 70
Fax: 044 - 730 70 67
www.dewalt.ch
service@rofoag.ch
Ireland
DEWALT
Calpe House Rock Hill
Black Rock, Co. Dublin
Tel: 00353-2781800
Fax: 00353-2781811
www.dewalt.ie
Italia
DEWALT
via Energypark
20871 Vimercate (MB), IT
Tel:
800-014353
39 039 9590200
Fax: 39 039 9590313
www.dewalt.it
Nederlands
Tel: 31 164 283 063
DEWALT Netherlands BV
Holtum Noordweg 35
Fax: 31 164 283 200
6121 RE BORN, Postbus 83, 6120 AB BORN
www.dewalt.nl
Norge
DEWALT
Postboks 4613, Nydalen
0405 Oslo
Tel: 22 90 99 10
Fax: 45 25 08 00
www.dewalt.no
kundeservice.no@sbdinc.com
Österreich
DEWALT
Werkzeug Vertriebsges m.b.H
Oberlaaerstrasse 248, A-1230 Wien
Tel: 01 - 66116 - 0
Fax: 01 - 66116 - 614
www.dewalt.at
service.austria@sbdinc.com
Portugal
DEWALT Limited, SARL
Tel: 214 66 75 00
Centro de Escritórios de Sintra Avenida
Fax: 214 66 75 80
Almirante Gago Coutinho, 132/134, Edifício 14
2710-418 Sintra
www.dewalt.pt
resposta.posvenda@sbdinc.com
Suomi
DEWALT
Tekniikantie 12, 02150 Espoo
02150 Espoo, Finland
Puh: 010 400 43 33
Faksi: 0800 411 340
www.dewalt.fi
asiakaspalvelu.fi@sbdinc.com
Sverige
DEWALT
Box 94
431 22 Mölndal
Tel: 031 68 60 60
Fax: 031 68 60 08
www.dewalt.se
kundservice.se@sbdinc.com
Türkiye
KALE Hırdavat ve Makina A.Ş.
Defterdar Mah. Savaklar Cad. No:15
Edirnekapı / Eyüp / İSTANBUL 34050
TÜRKİYE
Tel: 0212 533 52 55
Faks: 0212 533 10 05
www.dewalt.com.tr
United
Kingdom
DEWALT, 210 Bath Road;
Slough, Berks SL1 3YD
Tel: 01753-567055
Fax: 01753-572112
www.dewalt.co.uk
emeaservice@sbdinc.com
Australia
DEWALT
82 Taryn Drive, Epping
VIC 3076 Australia
Tel: Aust 1800 338 002
Tel: NZ 0800 339 258
www.dewalt.com.au
www.dewalt.co.nz
Middle East Africa
DEWALT
P.O. Box - 17164,
Jebel Ali Free Zone (South), Dubai, UAE
Tel: 971 4 812 7400
Fax: 971 4 2822765
www.dewalt.ae
Service.MEA@sbdinc.com
N404990
32 15 47 37 63
32 15 47 37 64
32 15 47 37 99
www.dewalt.be
enduser.BE@SBDinc.com
06/14
Download PDF